Emerald Spa | DS-4 | Instruction manual | Emerald Spa DS-4 Instruction manual

DS3 SERIES
Object detection and measurement light grid
INSTRUCTION MANUAL
DATASENSOR S.p.A. Via Lavino 26 5
4005 0 Monte S. Pietro - Bolog na - Italy
Tel: +39 051 676 561 1
Fax: +39 051 6759 324
http://www.datasensor.com
e-mail: info@datas ensor.com
DATASENSOR S.p.A. cares for the environment: 100 % recycle d pap er.
DATASENSOR S.p.A. reserves the right to make modificati ons an d improv ements with out prior n otificatio n.
DECLARATION OF CONFORMITY
We
DATASENSOR S.p.A.
Via L avino, 265
40050 Monte San Pietro
Bologna - Italy
declare under our sole responsibility that the product(s)
DS3-XX-XXX,
OPTOELECTRONIC LIGHT GRID FOR OBJECT
DETECTION AND MEASUREMENT AND ALL IT S
MODELS
to which this declaration relates in conformity with the following
international standard(s) or other normative document(s)
CEI EN 61000-4-3, NOVEMBER 1997:
E LECTROMAGNETIC COMPATIBILITY (EMC). P ART 4: TESTING AND MEASUREMENT
TECHNIQUES. S ECTION 3: RADIATED, RADIO -FREQUENCY, ELECTROMAGNETIC FIELD
IMMUNITY TEST
CEI EN 61000-4-4, SEPTEMBER 1996:
E LECTROMAGNETIC COMPATIBILITY (EMC). P ART 4: TESTING AND MEASUREMENT
TECHNIQUES. SECTION 4: E LECTRICAL FAST TRANSIENT /BURST IMMUNITY TEST
CEI EN 61000-4-6, NOVEMBER 1997:
E LECTROMAGNETIC COMPATIBILITY (EMC). P ART 4: TESTING AND MEASUREMENT
TECHNIQUES. S ECTION 6: IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY
RADIO -FREQUENCY FIELDS
CEI EN 50319, OTTOBER 2000:
ANALOG OUTPUT ON PROXIMITY SWITCH
CEI IEC 60947-5-2, MARCH 1999:
LOW VOLTAGE PROXIMITY SWITCH
Following the provision of the Directive(s):
89/336 CEE AND SUCCESSIVE AMENDMENTS
Monte San Pietro, 02/08/2001
Gianni Stradi otti
UNI EN ISO 1 400 1
Quality Ass uranc e Manager
DS series
Instructions manual
INDEX
1. GENERAL INFORMATION .........................................................................................pag.
1.1. General description of the AREAscanä
ä light grid.......................................pag.
1.2. Selecting the devic e...........................................................................................pag.
1.3. Typic al applications ............................................................................................pag.
1
1
2
3
2. INSTALL ATION MODE ...............................................................................................pag.
2.1 Precautions to be obs erved for the choic e and i nstallation of the device .pag.
2.2. General information on the device positioning ..............................................pag.
2.2.1. Minimum installation distance.............................................................pag.
2.2.2. Minimum distance from reflec ting surfac es .....................................pag.
2.2.3. Installation of s everal adj acent light grids .........................................pag.
4
4
5
5
6
8
3. MECHANICAL MOUNTING........................................................................................pag. 9
4. ELECTRICAL CONNECTIONS..................................................................................pag. 10
4.1. Notes on the connec tions ....................................................................................pag. 11
5. FUNCTION SELECTION .............................................................................................pag. 13
5.1. Standard configuration ........................................................................................pag. 13
6. CALIBRATION PROCEDURE....................................................................................pag. 15
6.1. Correct calibration procedure gui de ..................................................................pag. 15
7. FUNCTIONING MODE.................................................................................................pag.
7.1. Scanning mode...................................................................................................pag.
7.2. Measurement mode ...........................................................................................pag.
7.2.1. Absolute measurement........................................................................pag.
7.2.2. Relative measurement.........................................................................pag.
7.3. Object detection mode (teac h-in).....................................................................pag.
7.3.1. Absolute detection................................................................................pag.
7.3.2. Relative detection.................................................................................pag.
7.3.3. Detection toleranc e ..............................................................................pag.
7.4. DARK/LIGHT mode of the output ....................................................................pag.
7.5. Sensiti vity mode..................................................................................................pag.
16
16
18
18
19
20
21
22
22
23
23
8. DIAGNOSTIC FUNCTIONS ........................................................................................pag.
8.1. Visualisation of the devic e status .....................................................................pag.
8.2. Fault and diagnostic messages ........................................................................pag.
8.2.1. Diagnos tic mode...................................................................................pag.
8.2.2. Error mode.............................................................................................pag.
24
24
25
25
26
9. CHECKS AND PERIODIC AL M AINTENANCE.......................................................pag. 27
10. TECHNICAL DAT A ......................................................................................................pag. 28
11. LIST OF THE AVAIL ABLE MODELS .......................................................................pag. 29
12. OVERALL DIMEN SIONS ............................................................................................pag. 30
Instructions manual
DS series
1. GENERAL INFORMATION
1.1.
General description of the ARE Ascan
TM
light grid
TM
The AREAscan light grids are optoelectronic multibeam devices that
can be used to detect transparent and small objects and for
dimensional measurement. The variety of possibile functions makes
DS3 a particularly flexible device suitable to many different
applications.
TM
The AREAscan light grids of the DS3 series are manufactured in
accordance with the international standards in force and in particular:
CEI EN 60947-5-2:
low voltage proximity switch
CEI EN 50319:
analog output on proximity switch
The device, consisting of one emitter and one receiver units housed
inside strong aluminium profiles, generates infrared beams that detect
any object positioned within the light grids detection field.
The command and control functions are inside the two units; the
connections are made through a M12 connector located in the lower
side of the profile.
The synchronisation between the emitter and the receiver takes place
through direct connection (via cable) between the two units.
The control and management of the emitted and received beams are
guaranteed by a microprocessor that, using LEDs, supplies to the
operator information relative to the light grid status and any error
conditions.
1
DS series
Instructions manual
Some parts or paragraphs of this manual containing important
information for the operator are preceded by a note:
Notes and detailed descriptions about particular characteristics of the
AREAscanTM devices in order to better explain their functioning.
DATASENSOR technical assistance is available for any necessary
information related to the functioning and/or installation of the DS3
series light grids (see section 9 “Checks and periodical maintenance”).
1.2.
Selecting the device
The choice of the device may be based on the following:
- detection area needed. This is the height of the device’s sensitive
zone
- maximum operating distance. This is the distance between the
emitter unit (TX) and receiver unit (RX)
Four versions are available:
DS3-SD-015
DS3-SD-030
DS3-LD-015
DS3-LD-030
Operating distance
0.2 … 0.6 m
0.2 … 0.6 m
0.6 … 1.5 m
0.6 … 1.5 m
Detection field
24 beams; h=150 mm
48 beams; h=300 mm
24 beams; h=150 mm
48 beams; h=300 mm
The functions that characterise the DS3 AREAscanTM light grids are
available on all 4 versions that consequently have the same operating
modes.
The specific technical characteristics (e.g. resolution, sensitivity etc)
remain the same for all the versions, until differently indicated.
For food industry applications, please verify with DATASENSOR
Technical Service the compatibility of the materials of the light grid
shell with the eventual chemical agents that are used in the production
process.
2
Instructions manual
1.3.
DS series
Typical applications
The following images supply an overview on some of the main
applications.
3
Object detection and measurement on conveyor
belt
Control of the correct material positioning
(opaque and transparent) during functioning
(plastic, metal, paper etc)
Loop control and positioning (also transparent
material)
Detection of objects w ith different shapes in the
food industry
Detection of objects in different positions (parallel
beams)
Detection of small objects in different positions
(crossed beams)
DS series
2
Instructions manual
INSTALLATION MODE
2.1.
Precautions to be observed for the choice and installation of the device
•
The dimension of the smallest object to be detected should not to
be lower than the resolution level of the device.
•
The DS3 should be installed in a place compatible with the
technical characteristics (see section 10 “Technical Data”) of the
TM
AREAscan light grids.
Other considerations:
-
avoid installation near very intense and/or flashing light sources,
in particular near the receiver unit.
-
strong electromagnetic interferences can compromise the
correct functioning of the device. Please contact DATASENSOR
Technical Service when this problem occurs.
-
the operating distance of the device can be reduced in the
presence of smog, fog or airborne dust.
-
a sudden change in environment temperature, with very low
minimum peaks, can generate a small condensation layer on the
lenses and jeopardise functioning.
4
Instructions manual
2.2.
DS series
General information on the device positioning
•
Place the device near the detection area.
•
Align the receiver (RX) and emitter (TX) units parallel to one
another.
•
Fix the receiver and emitter units on rigid supports not affected by
strong vibrations using the specific brackets (see section 3
“Mechanical mounting”).
•
Check that the distance between the receiver and emitter units is
within the device operating distance (see section 10 “Technical
data”).
2.2.1. Minimum installation distance
The minimum installation distance corresponds to the minimum
operating distance (= 20 cm for short distance versions; = 60 cm for
long distance versions).
It is recommended that the distance be slightly increased to avoid
problems deriving from the imperfect alignment of the two units.
5
DS series
Instructions manual
2.2.2. Minimum distance from reflecting surfaces
Reflecting surfaces placed near the light beams of the AREAscanTM
device (over, under or laterally) may cause passive reflections; these
reflections could compromise the recognition of an object inside the
controlled area (see Fig.1).
Fig. 1
However, if the receiver detects a secondary beam (reflected by the
side-reflecting surface) the object cannot be detected, even if the main
beam is interrupted by the entering object.
6
Instructions manual
DS series
It is thus important to position the light grid according to the minimum
distance from any reflecting surface.
The minimum distance depends on:
- Device operating distance
- Reflecting surface nature
- Position of the object inside the sensitive area
The minimum distance of the reflecting object has to be:
DS3-SD
d > 7 cm
DS3-LD d > 12 cm
If the distance between the receiver and emitter is between 60 and 90
cm
DS3-LD d > 25 cm
If the distance between the receiver and emitter is between 90 and 150
cm
NOTE:
7
These v alues are based on a mirrored surface sample
w ith an 80% reflecting index.
DS series
Instructions manual
2.2.3. Installation of several adjacent light grids
When several devices must be installed in adjacent areas, care must
be taken to prevent interference between the emitter of one device and
the receiver of another.
Fig.2 gives an example of possible interferences between different
devices and two pertinent solutions.
NO
YES
YES
Fig. 2
8
Instructions manual
DS series
3. MECHANICAL MOUNTING
The emitting and receiving bars must be installed with the relevant
sensitive surfaces turned towards each other;
the connectors must be positioned on the
same side and the distance must be included
within the operating range of the model used
(see section 10 “Technical data”).
Once they have been positioned, the two bars
should be aligned and completely parallel.
To mount the device, use the threaded pins
supplied (Fig.3); insert them into the slots on
Fig. 3
the two bars.
The operator can use the pins and/or the rigid mounting brackets –
supplied with the device – depending on the particular application
and/or the type of support on which the two bars must be placed (see
Fig.4).
Fig. 4
Rigid brackets can be used where no large mechanical corrections are
required, during the alignment operation.
The rotating supports for the correction of the bars’ inclination of ±1°
on the median transversal axis and of ±5° on the longitudinal axis, are
available on request.
For applications with particularly strong vibrations, it is advisable to use
anti-vibration shock absorbers capable of reducing the impact of the
vibrations. These should be installed with threaded pins, rigid brackets
and/or rotating supports.
9
DS series
Instructions manual
4. ELECTRICAL CONNECTIONS
The electrical connection between the emitter and receiver units is
made through male M12 connectors, located in the lower part of the
light grids.
ANALOG OUTPUT
(TX ç ) D+
6
GND
5
PNP OUTPUT
4
7
3
NOT USED
2
1
(TXç ) D-
+24VDC
8
REMOTE TEACH-IN/CALIBRATION
1
2
3
4
5
6
7
8
RECEIVER (RX):
=
=
=
=
=
=
=
=
white
brown
green
yellow
grey
pink
blue
red
(RX è ) D+
GND
EMITTER (TX):
2
1
3
4
1
2
3
4
=
=
=
=
=
=
=
=
=
=
=
=
SYNC D+Vdc
NOT USED
PNP output
Analog output
SYNC D+
0V
REMOTE TEACH-IN/
CALIBRATION
+VDC
D-( ç RX)
brown
white
blue
black
=
=
=
=
+Vdc
SYNC D+
0V
SYNC D-
10
Instructions manual
DS series
4.1. Notes on the connections
For the correct functioning of the AREAscanTM. light grid, the following
precautions regarding the electrical connections should be taken:
•
Sheilded cables are not foreseen in the standard connection.
However, if necessary, these cables can be used; in this case
ground connection is necessary of both the unit and cable, as
shown in Fig.5.
Fig. 5
The cables must not be placed in contact with or near any high voltage
cable (e.g. motor power supply, inverters, etc.). The correct functioning
of the device can be compromised.
11
DS series
Instructions manual
•
The AREAscanTM are NOT safety devices and so MUST NOT be
used to control the safety of the machines where installed.
•
The ground connection of the two units is not necessary. However,
if required, the connection is possible; tighten the special screw –
supplied with the device – instead of one of the 8 screws that lock
the heads of each bar (see Fig.6).
•
Follow the connection illustrated in Fig.5 when ground connection
of the entire system is used.
Fig. 6
12
Instructions manual
DS series
5. FUNCTION SELECTION
The functions implemented in the AREAscanTM devices can be
selected using the dip-switches inside the receiver unit as shown in
Fig.7.
The SET pushbutton, necessary for the calibration procedure (see
section 6 “Calibration Procedure”) and teach-in function (see section
7.3 “Teach-in detection of objects”), is present on the same unit.
SET pushbutton
DIP-SWITCH
Fig. 7
5.1. Standard configuration
The device is supplied with the following standard configuration:
- Parallel beams
- Calibration at powering on
- Aboslute measurement mode with V OUT min at channel 1
- Sensitivity at level 9
13
DS series
Instructions manual
Table 1 indicates the type of function and the relative position of the
dip-switches.
Tab. 1
NOTE: The dip-sw itches not used are show n in grey.
Black indicates the position of the dip-switch lever used.
14
Instructions manual
DS series
6. CALIBRATION PROCEDURE
The calibration procedure sets the signal level that arrives from the
receiver in the rest condition (no object detection).
In every other condition, the acquired signal will be compared to the
one acquired during the calibration.
The calibration depends on the alignment and distance of the two
units; the procedure must be repeated every time these parameters
change.
6.1. Correct calibration procedure guide
The calibration can be done according to the following procedure, once
the mechanical mounting, electrical connections and alignment are
completed:
•
Switch ON the DS3.
•
In the CALIBRATION AT POWERING mode (see function 4 in
Tab.1 at page 14), the system will automatically calibrate itself at
the powering on. Successive calibrations during functioning have to
be made according to the following mode.
•
In the MANUAL CALIBRATION mode (see function 3 in Tab.1 at
page 14), press and release the SET pushbutton.
The calibration phase can have a variable duration and ends when
the green LED lights up in a steady manner; the system functions
only at this moment.
•
No undesired object should be present in the detection area during
the calibration process. The calibration procedure can be made
even if an object will remain fixed inside the detection area (e.g.
support, paper etc). In this case, area affecting the fixed object will
be excluded from the total sensitive area (BLANKING mode).
The powering on of the red LED (ERROR FAILURE) indicates this
particular situation.
•
The position of both the receiver and emitter must remain the same
both during and after calibration (the use of specific anti-vibration
brackets are suggested in case of particularly critical applications
characterised by strong vibrations).
15
DS series
Instructions manual
7. FUNCTIONING MODE
The DS3 light grid is a detection and measurement device and thus the
beam interruption due to an object causes the switching of the digital
output (PNP type) and/or the change of the analog output signal. Small
objects (up to 0.5 mm), transparent films and measurement of
geometrical dimensions with a 6 mm resolution, can be obtained by
setting the device at the right sensitivity.
The different functioning modes available are listed below:
7.1. Scanning mode (see functions 1 and 2 of Tab.1 at page 14)
Two different scanning types can be accomplished with the
AREAscanTM of the DS3 series:
•
Scanning with PARALLEL beams: where each single
photoreceiver is illuminated only by the beam of the corresponding
photoemitter with a precise scanning sequence (this mode
activates only one photoreceiver/photoemitter couple each time,
during the scanning cycle).
This mode can be used both for the detection of objects as well as
the dimensional measurement (this measurement is supplied to the
operator by the analog output 0-10V). The minimum object that can
be detected has to be ≥ 6 mm (that represents the minimum
resolution (R), Fig.8, of the device in this mode).
Fig. 8
16
Instructions manual
•
DS series
Scanning w ith CROSSED beams: where several photoreceivers
are illuminated by the beam of a single photoemitter (this mode
activates a series of photoreceivers and one photoemitter
contemporarily, during the scanning cycle). The scanning with
crossed beams can be used for the detection of objects with small
dimensions and, in particular, for the detection of transparent
objects. The minimum object that can be detected is ≥ 0.5 mm
(that represents the minimum resolution of the device in this mode).
The real resolution of the device also depends on the object’s
position in the detection field, as shown below (Fig.9).
The analog output is not activated in this mode.
Fig. 9
17
DS series
7.2.
Instructions manual
Measurement mode
7.2.1. Absolute mode (see functions 5 and 6 of Tab.1 at page 14)
Provides the measurement of the dimension of the object beginning
from an absolute reference. The first photoelement is taken as a
reference (1) beginning from the connector side. The analog output
voltage is proportional to the number of beams (obscured and not)
included between the reference and last beam effectively obscured.
The level of the analog output voltage can be selected using the dipswitches (functions 5 and 6 of Tab.1 at page 14 – respectively V OUT
max. at channel 1 and V OUT min. at channel 1); the voltage can thus be
maximum or minimum in correspondence to the obscuring of the beam
taken as a reference.
Fig. 10 can be taken as an example: the obscuring of the beams is
considered as corresponding to the VOUT of 1V variation. At the
obscuring of the last beam, the VOUT reaches the 10V full scale. If the
VOUT min. option is set to the channel 1 (A), the VOUT in question will
be = 6V; on the contrary will be = 7V (B).
The PNP output is active when at least one photoelement is obscured.
The function of the absolute measurement is activ e only w ith the
parallel beam mode.
A
B
Analog output
VOUT min. to channel 1
VOUT max. to channel 1
Output level
6V
7V
PNP output
ON
Fig. 10
18
Instructions manual
DS series
7.2.2. Relative measurement (see function 7 of Tab.1 at page 14)
Provides the measurement of the dimension of the object that affects
the detection area independently from an absolute reference.
The voltage of the analog output is proportional to the number of
beams effectively obscured.
Fig. 11 can be used as an example, considering the previous
hypothesis (one obscured beam corresponds to V OUT = 1V).
The PNP output is active when at least one photoelement is obscured.
The function of the relativ e measurement is active only w ith the
parallel beam mode.
Analog output
PNP output
3V (4, 5, 6 c hannels)
ON
Fig. 11
19
DS series
7.3.
Instructions manual
Detection mode (teach-in)
The teach-in mode can be selected using the dip-switches (see
functions 9 and 10 of Tab.1 at page 14) and is active only with one of
these selections.
This mode allows the memorisation of the dimension of one or more
objects (not adjacent) by pressing the SET pushbutton. The PNP
output is then switched on when the objects pass in the sensitive area.
The teach-in mode is activated effecting the following phases:
•
Place the object inside the sensitive area in the desired position.
•
Press for at least 2 seconds the SET pushbutton.
•
Release the pushbutton after the powering on of the red LED.
The object detection is indicated by the successive powering on of the
green LED.
The presence of the memorised object will allow the switching ON of
the digital output (PNP) and powering on of the relative yellow LED.
The characteristics of the memorised object remain valid until another
successive teach-in detection is made.
In the teach-in mode, the system forces the parallel beam mode
independently from the dip-switch setting (dip-switch N°1) that, only in
this configuration, is used to select the detection mode.
The function of the detection mode (teach-in) is active only w ith
the parallel beam mode.
Fig. 12
20
Instructions manual
DS series
The following operating modes can be selected using the dip-switches:
7.3.1. Absolute detection (see function 9 of Tab.1 at page 14)
The digital output (PNP) switches only if a certain object (dimensions
previously memorised) passe s exactly in the desired position (Fig.13).
The analog output in this configuration is always active and the voltage
is proportional to the number of obscured optics (also non adjacent)
independently from the real switching of the digital output (PNP)
caused by the object detection.
Analog output
PNP output
Analog output
PNP output
= 3V (4,5,6 channels)
ON
= 3V (1,2,3 channels)
OFF
Analog output
PNP output
= 5V (4,5,6,7,8 channels)
OFF
Fig. 13
21
DS series
Instructions manual
7.3.2. Relative detection (see function 10 of Tab.1 at page 14)
The digital output (PNP) switches each time a certain object passe s
inside the sensitive area, independently from its position in the area
(Fig.14).
The analog output in this configuration is always active and the voltage
is proportional to the number of obscured optics (also non adjacent)
independently from the real switching of the digital output (PNP)
caused by the object detection.
Analog output
PNP output
Analog output
PNP output
= 3V (4,5,6 channels)
ON
= 3V (1,2,3 channels)
ON
Analog output
PNP output
= 5V (4,5,6,7,8 channels)
OFF
Fig. 14
7.3.3.
Detection tolerance (see functions 11 and 12 of Tab.1 at page 14)
The tolerance of the detected object’s measurement can be changed
by means of the the dip-switches; in detail it is possible to select
between an exact detection and detection with a tolerance channel.
22
Instructions manual
DS series
7.4. DARK/LIGHT mode of the output (see function 13 and 14 of Tab.1 at page 14)
Defines the status of the digital output (PNP) and of the relative yellow
signalling LED.
DARK MODE
Object detection
YES
NO
Output status
OFF
ON
LED status
Turned off
Turned on
Object detection
YES
NO
LIGHT MODE
Output status
ON
OFF
LED status
Turned on
Turned off
7.5. Sensitivity mode (see f unctions 15÷18 of Tab.1 at page 14)
This function allows the sensitivity adjustment according to the
characteristics of the object to be detected.
The standard value is fixed on level 9; in presence of small objects
(comparable to the detection limit = 0.5 mm) or very transparent
objects, with the units at the maximum operating distance, we
recommend increasing the sensitivity to level 5.
In all other cases, such as when the detection or the calibration
procedure is very difficult, we recommend decreasing the sensitivity to
level 15.
The sensitivity increase is recommended only if strictly necessary, as
the increase can deteriorate the immunity characteristics and require
more frequent calibration operations.
Operating on the 5 and 9 sensitivity levels (high sensitivity) can be
accomplished only in the manual calibration mode.
23
DS series
Instructions manual
8. DIAGNOSTIC FUNCTIONS
8.1. Visualisation of the device status
The operator can verify the operating status of
the DS3 device through three LEDs present on
the receiver unit and one LED present on the
emitter unit.
The meaning of the LEDs present on the receiver unit (RX) depends
on the functioning mode of the light grid.
RECEIVER UNIT
Signal
Status
- Normal device functioning.
- Absence of the device after
calibration.
- Switching signalling fo the
PNP output.
EMITTER UNI T
Signal
Status
- Normal device functioning.
The diagnostic described makes reference to LIGHT mode output
(obj ect detection signalled by OUT LED ON).
24
Instructions manual
DS series
8.2. Fault and diagnostic messages
The operator can verify the device functioning status and the stop or
failure causes of the system, using the same LEDs used for the
visualisation of the functions.
8.2.1.
Diagnostic mode
RECEIVER UNIT
Signal
Cause
- No power supply.
Check
- Verify the power supply.
- Device ready for teach-in
detection;
release
the
TEACH-IN
button
to
memorise the object.
- Control
the presence of an
external object inside the
detection area and remove it.
EMITTER UNI T:
Signal
Cause
- No power supply.
25
Check
- Verify the power supply.
DS series
8.2.2.
Instructions manual
Error mode
RECEIVER UNIT
Signal
Cause
Check and Repair
- PNP output does not switch. - Align the device again and
inside the maximum operating
- Device failure.
distance.
- Device not aligned or
outside the
maximum - Repeat the calibration
procedure.
operating distance.
- Turn off and on the device; if the
anomaly persists replace the
unit.
- PNP output switches.
- Align the device again and
- Device not aligned or inside the maximum operating
outside the
maximum distance.
- Control the presence of an
operating distance.
external object inside the
- Wrong calibration.
caliobration area and remove it
and repeating the calibration.
TM
The AREAscan will operate
according to the modes of
section 6 “Calibration
Procedure”.
26
Instructions manual
DS series
9. CHECKS AND PERIODICAL MAINTENANCE
The following is a list of recommended check and maintenance
operations that should be periodically carried out by qualified
personnel.
Check that:
•
The dev ice has been calibrated, regularly repeating the calibration
procedure (section 6 “Calibration procedure”).
•
The operating distance and alignment of the units conforms to the
indications giv en in section 2 “Installation mode” and section 10 “Technical
data”.
•
The dev ice and external electrical connections are not damaged.
The frequency of checks depends on the particular application and on
the operating conditions of the light grid.
The AREAscanTM devices do not need any particular maintenance,
with the exception of the cleaning of the protection frontal surfaces of
the optics.
When cleaning, use a cotton cloth dampened with water.
Do not under any circumstances use:
- alcohol or solvents
- w ool or synthetic cloths
Disturbances that cause power failure can cause the temporary
opening of the outputs, do not compromise the functioning of the grid.
All appliances are under a 18 month guarantee from the manufacturing
date. Datasensor will not be liable for any damages to persons and
things caused by the non-observance of the correct installation modes
and device use.
The warranty will not cover damages caused by incorrect installation,
incorrect use and accidental causes such as bumps or falls.
In the event of breakdown send the appliance to DATASENSOR S.p.A.
Sales Technical Service
Tel.:
+39 051 6765611
Fax.: +39 051 6759324
email: service@datasensor.com
27
DS series
Instructions manual
10. TECHNICAL DATA
Power suppl y:
Consumpti on of emitter unit (TX):
Consumpti on of recei ver unit
(RX):
Outputs:
Output c urrent on PNP output:
Output voltage on PNP output:
Response ti me:
Light emission:
Resolution of crossed beams:
24 Vdc ± 15%
100 mA max
100 mA max without load
1 PNP output; load max 10 kΩ
1 analog output ; 0-10V (∆Vmax. 5%)
100mA; short circuit protecti on
-1 V of the power s uppl y at T=25°C
Refer to “Available models” table page30
Infrared (880 nm)
DS3-SD: 0.5mm (s ee pag.17)
DS3-LD: 0.8mm (see pag.17)
Resolution of parallel beams and
minimum object detected
Accurac y
on
relati ve
measurement (parallel beams):
Accurac y
on
abs olute
measurement (parallel beams):
Dimensional difference of equall y
detected objects in abs olute
teac h-in:
Dimensional difference of equall y
detected objec ts in relative teac hin:
6mm
Operati ng distance:
0.2 - 0.6 m Short distanc e version (SD)
0.6 - 1.5 m Long distance version (LD)
see page 14
- 10…+ 55 °C
- 25…+ 70 °C
15…95 % (non condensating)
Classe 1
IP 65 (EN 60529)
0,7 mm width, 10 … 55 Hz frequenc y,
10 s weep for X, Y, Z axis ; 1oc tave/min.,
(EN 60068-2-6)
16 ms (ca. 10 G) 1.000 shoc k for axis
(EN 60068-2-29)
Painted aluminium (RAL9005 s hiny blac k)
PMMA
M12-4 pole c onnector for TX
M12-8 pole c onnector forRX
DS3-015: 310 g. for unit
DS3-030: 530 g. for unit
Available functions:
Operati ng temperature:
Storage temper ature:
Humidity:
Electrical protection:
Mechanic al protection:
Vibrations:
Shoc k r esistanc e:
Housing material:
Optics material:
Connections :
Weight:
± 6mm
± 3mm
± 6mm
∆ = 12mm
28
Instructions manual
DS series
11. LIST OF AVAILABLE MODELS
29
Response
time of
crossed
beams
Response
time of
parallel
beams
Model
Length of
sensitiv e
area
DS3-LD-015
155
155
24
23
msec
3
msec
0.6…1.5
DS3-LD-030
305
305
48
46
msec
6
msec
0.6…1.5
DS3-SD-015
155
155
24
23
msec
3
msec
0.2…0.6
DS3-SD-030
305
305
48
46
msec
6
msec
0.2…0.6
Length of
N°.
controlled
beams
area
MODEL
a x b (mm)
h (mm)
DS3-LD-015
DS3-LD-030
DS3-SD-015
DS3-SD-030
35 x 40
226
35 x 40
376
35 x 40
226
35 x 40
376
Operating
distance
(m)
DS series
Instructions manual
12. OVERALL DIMENSIONS
All the dimensions given are in mm.
RECEIVER
EMITTER
30
Download PDF