Advertisement
Advertisement
MICRO-STAR INT’L
Version 1.4
Nov. 2003
G52-W6967X3
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
Notice 1
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Notice 2
Shielded interface cables and A.C. power cord, if any, must be used in order to comply with the emission limits.
VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AU
RESEAU.
FCC ID: I4L-MS6967/MS6968
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
FCC Requirement
This equipment complies with Part 68 of the FCC Rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration
Number, Ringer Equivalence Number (REN) and USOC jack type for this equipment. You must, upon request, provide this information to your telephone company.
An FCC compliant telephone cord and modular jack is provided with this equipment.
This equipment is designed to be connected to the telephone network or premise wiring use a compatible modular jack which is Part 68 compliant. See installation instructions for details.
The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when your telephone number is called. In most, but not all areas, the sum of the REN of all devices connected to on line should not exceed five (5.0). To be certain of the number of devices you may connect to your line, as determined by the REN, you should contact your local telephone company to determine the maximum REN for your calling area. If your telephone equipment causes harm to the telephone network, the Telephone Company may discontinue your service temporarily. If possible, they will notify you in advance, but if advance notice is not practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with the FCC.
Your telephone company may make changes in its facilities, equipment, operations or procedures that could affect the proper functioning of your equipment. If they do, you will be notified in advance to you an opportunity to maintain uninterrupted telephone service.
If you experience trouble with this telephone equipment, please contact MICRO-
STAR INTERNATIONAL for information on obtaining service or repairs. The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning.
This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to stat tariffs.
Copyright Notice
The material in this document is the intellectual property of MI-
CRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice.
Trademarks
All trademarks used in this manual are the sole property of their respective owners.
Pentium is a registered trademark of Intel Corporation.
Windows is a registered trademark of Microsoft Corporation.
Revision History
Revision
V 1.2
V 1.3
V1.4
Revision History
Software update
Adding “Human Interface
Device”
Adding “Security Code”
Date
Feb. 2003
Nov. 2003
Nov. 2003
Important Safety Precautions
Always read and follow these basic safety precautions carefully when handling any piece of electronic component.
1. Keep this User’s Manual for future reference.
2. Keep this equipment away from humidity.
3. Lay this equipment on a reliable flat surface before setting it up.
4. The openings on the enclosure are for air convection hence protects the equipment from overheating.
5. All cautions and warnings on the equipment should be noted.
6. Never pour any liquid into the opening that could damage or cause electrical shock.
7. If any of the following situations arises, get the equipment checked by a service personnel: z
The USB cable is damaged z
Liquid has penetrated into the equipment z
The equipment has been exposed to moisture z
The equipment has not work well or you can not get it work according to User’s Manual z
The equipment has dropped and damage z
If the equipment has obvious sign of breakage
8. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT
UNCONDITIONED, STORAGE TEMPERATURE ABOVE 60 0 C OR
BELOW -20 0 C, IT MAY DAMAGE THE EQUIPMENT.
CONTENTS
1. Introduction ................................................................................ 1
1.1 Bluetooth Technology ........................................................... 1
1.2 MSI™ PC2PC Bluetooth ...................................................... 1
1.3 Hardware Specifications ......................................................... 2
2. Installation .................................................................................. 5
2.1 Package Checkup .................................................................... 5
2.2 Software Installation .............................................................. 6
2.3 Hardware Installation ............................................................. 9
3. Software Operations -- My Bluetooth Places ................. 1 3
3.1 Introduction ........................................................................... 1 3
3.2 Basic Operations ................................................................... 1 9
3.3 Configure Bluetooth ............................................................. 2 6
3.4 Security .................................................................................. 7 4
3.5 Troubleshooting .................................................................... 7 8
4. Technical Support .................................................................... 8 3
5. Glossary ..................................................................................... 8 5
User’s Guide
1. Introduction
1.1 Bluetooth Technology
The term “Bluetooth” refers to a worldwide standard for the wireless exchange of data between two devices. In order to exchange data, two Bluetooth devices must establish a connection.
Before a connection is established, one device must request a connection with another. The second device accepts (or rejects) the connection.
The originator of the request is known as the client. The device that accepts (or rejects) the request is known as the server.
Many Bluetooth devices can act as both client and server.
A client Bluetooth device runs a software program that requests a connection to another device as part of its normal operation.
For example, the program may request a connection to a remote computer, a printer, or a modem. Becoming a Bluetooth client normally requires an action by the device operator, such as an attempt to browse a remote computer, print a file, or dial out on a modem.
Every Bluetooth device that provides a service must be prepared to respond to a connection request. Bluetooth software is always running in the background on the server, ready to respond to connection requests.
1.2 MSI™ PC2PC Bluetooth
MSI™ PC2PC Bluetooth provides wireless technology that revolutionizes personal connectivity. It is the solution for the seamless integration of Bluetooth technology into personal computers,
1
PC2PC Bluetooth enabling short-range wireless connections between desktop/laptop computers, Bluetooth-enabled peripherals (printers, faxes,...), portable handheld devices, and connectivity to the Internet.
1.3 Hardware Specifications
Bluetooth Transceiving Key/Module
General
H/W Interface
Bluetooth Spec.
Compliance
Throughput
Operating Volt.
USB
Ver. 1.1
About 723Kbps (data channels)
5V from USB interface
Operating Range Up to 200M for open space (depending on the environment)
Regulatory Approval FCC, CE, BQB (Bluetooth Qualified), BSMI
Temperature Storage temp: -10 o C~+70 o C
Operating temp: -10 o C~+70 o C
Radio
Spread Spectrum Frequency Hopping Spread Spectrum (FHSS)
Compliant with FCC part 15
Frequency Range
RF Channels
2.4~2.4835GHz (2.4GHz ISM Band)
79-channel system for USA, Japan, and Europe
(except France, 23-channel system for France)
GFSK, BT=0.5
Modulation
Output Power Class
Output Power
Receiver Sensitivity
Max Input Level
Power Control
Base Band
Physical Links
Bluetooth Power Class 1
+18dBm (Max.)
Better than -90dBm with BER < 0.1%
-20dBm
Yes
Support ACL link
2
User’s Guide
Network Capabilities Support piconet point-to-point and point-tomultipoint connections
Link Manager
3-slot Packets Yes
5-slot Packets
Slot Offset
Timing Accuracy
Switch
Yes
Yes
Yes
Yes
Hold Mode
Sniff Mode
Test Mode
Park Mode
RSSI
Power Control
Authentication
Encryption
Software
System Support
Profile Support
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Windows ® 2000/ME/98/XP
Generic Access Profile/Service Discovery
Profile/Serial Port Profile/Dial-Up Networking
Profile/Fax Profile/LAN Access Profile/Generic
Object Exchange Profile/File Transfer Profile/
Object Push Profile/Synchronization Profile/
Personal Area Network Profile/Hard Cable
Replacement Profile
3
4
PC2PC Bluetooth
NOTES
User’s Guide
2. Installation
2.1 Package Checkup
Unpack the package and inspect all the items carefully. If any of the items is damaged or missing, please contact your local dealer as soon as possible. Also, keep the box and packing materials at hand, in case you need to ship the unit in the future. Your package content may vary depending on the items purchased. It can be package 1, package 2, or the combination of both as listed below:
Package 1
Transceiving
Key
USB
Cable
Software
CD
User’s
Guide
Package 2
Transceiving
Module
Dipole
Antenna
Cable
(Optional)
User’s
Guide
5
PC2PC Bluetooth
2.2 Software Installation
1. Bluetooth Software version 1.4.2 build 10 will check the license of the hardware. Hence, if you intend to update the software from earlier versions (such as v1.3.x), you must
,in the first place, obtain a license key (security code) from WIDCOMM’s website (http://66.45.42.85/msi).
MSI Reminds You...
Be sure to get the unique license key (security code) for your Bluetooth dongle. Otherwise, if the software detects invalid license on the hardware, it will stop working and a warning message will pop up as follows.
6
User’s Guide
Key in the requested information and submit. The license key will be sent to you via e-mail shortly.
2. Download the Bluetooth software from MSI’s website
(http://www.msi.com.tw/). Unzip the file and double-click
setup.exe. Follow the on-screen instructions to install the software step by step.
3. Key in your Bluetooth dongle’s unique license key (security code) previously requested from WIDCOMM’s website.
7
8
PC2PC Bluetooth
4. After completion of the installation, please restart your computer.
MSI Reminds You...
1. Every MSI dongle has its unique license key (security code) and one license key can be used on one MSI dongle only. The Bluetooth software will not work if an unmatched security code is keyed in or a Bluetooth dongle of other brands is installed.
2. To use another dongle, enter a folder named
“svcpack” and double-click BTFaeSec.exe. Key in the dongle’s unique security code when the WIDCOMM
Security License dialog box pops up.
2.3 Hardware Installation
1.
2.
User’s Guide
Remove the computer case.
2a.
Install the transceiving module onto your mainboard. Procedures may differ depending on the location of the bluetooth pinheader on the mainboard.
Please refer to the following:
2b.
For mainboards with Bluetooth pinheaders located near the PCI slots, ex: MS-6398E, secure the connector on the lower part of the transceiving module directly onto the Bluetooth p i n h e a d e r . T h e n , f a s t e n t h e transceiving module to the mainboard with a bracket screw.
For mainboards with Bluetooth pinheaders located elsewhere (not near the PCI slots), ex: MS-6380E, use the linking cable to secure the identical connector on the transceiving module to the Bluetooth pinheader on the m a i n b o a r d . T h e n , f a s t e n t h e transceiving module to the mainboard with a bracket screw.
9
PC2PC Bluetooth
3.
10
4.
Install and screw up the computer case.
Locate the antenna connector on the transceiving module bracket at the back panel of the computer case. Secure the dipole antenna to this connector and fix the antenna to a location free from signal obstruction. Concrete walls, metal substances, paints with metal composites,... etc. will cause signal obstruction and disable the
Bluetooth function.
5.
User’s Guide
Uncap the transceiving key.
6.
Connect the transceiving key to the USB cable and link the USB cable to an available USB port of the target device with which you wish to establish a wireless Bluetooth connection. The target device can be a desktop PC, a laptop PC, or any other types of
PCs with Windows ® OS & USB ports.
MSI Reminds You...
Avoid installing the transceiving module and the transceiving key into the same PC.
11
PC2PC Bluetooth
MSI Reminds You...
Note 1: The transceiving key and the transceiving module bracket both integrate one Green (Blue)
LED & one Red LED. The Green (Blue) LED indicates the connection status (LED on => under connection / LED off => disconnection or failed connection.). The Red LED indicates the power state
Note 2: As the Bluetooth pinheader shares the USB interface with blue-colored USB2.0 connector on the mainboard, utilization of the transceiving module will disable the bottommost USB2.0 port.
Note 3: To make sure that the hardware & software have been successfully installed, go to Control Panel after restarting your system. Double-click System and click the Device Manager tab. If the hardware
& software installation is complete, the MSI USB
Bluetooth Device should appear.
12
User’s Guide
3. Software Operations -- My Bluetooth Places
3.1 Introduction
1. Bluetooth Tray
The Bluetooth tray resides in the Windows system tray, which is normally located in the lower-right corner of the screen. The Bluetooth tray provides fast access to most
Bluetooth operations.
From the Bluetooth tray you can:
Access My Bluetooth Places—double-click the
Bluetooth icon, or right-click the Bluetooth icon and then select Explore My Bluetooth Places.
Access the Bluetooth Setup Wizard. This wizard will help you:
Configure how this computer accesses a service on another Bluetooth device
Locate remote Bluetooth devices
Configure the way that this computer provides services to remote Bluetooth devices
Set the name and type of this Bluetooth device, e.g., “John’s PC” and “Desktop.”
Access the Bluetooth Configuration Panel— right-click the Bluetooth icon, and then select Advanced Configuration.
Access the Quick Connect option—right-click the Bluetooth icon, select Quick Connect, and then select the type of service to which you wish to connect.
Start/Stop Bluetooth on this computer.
13
PC2PC Bluetooth
2. Access My Bluetooth Places
My Bluetooth Places is part of Windows Explorer.
There are multiple ways to access My Bluetooth Places:
In the Windows system tray
Right-click the Bluetooth icon and select Explore
My Bluetooth Places o r
Double-click the Bluetooth icon
On the desktop, double-click the Bluetooth icon
Open Windows Explorer and select My Bluetooth Places in the Folders pane or from the Address shortcut menu.
3. Icons Used For Bluetooth Devices And Services
Bluetooth icons provide at-a-glance feedback about a device or service’s status by changing appearance.
The Bluetooth icon in the Windows system tray provides feedback about Bluetooth status.
Figure 1: Bluetooth Icon
Bluetooth Icon Indicates Bluetooth Status
Enabled Disabled Connected
Blue with White Blue with Red Blue with Green
14
User’s Guide
Figure 2: Device Icons for Windows 9x, Me and 2K
Device Icons for Windows 9x, Me and 2K
Name Normal Connected Paired
Audio Gateway
Desktop
Headset
Laptop
Modem
Network Access Point
Personal Digital Assistant
Printer
Telephone
Unknown
15
PC2PC Bluetooth
Figure 3: Service Icons for Windows 9x, Me and 2K
Name
Audio Gateway
Service Icons for Windows 9x, Me and 2K
Normal Connected Not Available*
Dial-up Networking
Fax
Headset
Network Access
PIM Item Transfer
PIM Synchronization
Public Folder
Serial Port
* Services may be unavailable because they are in use or because the necessary hardware is not installed.
16
User’s Guide
Figure 4: Device Icons for Windows XP
Name
Audio Gateway
Normal Connected Paired
Desktop
Headset
Laptop
Modem
Network Access Point
Personal Digital Assistant
Printer
Telephone
Unknown Device
17
PC2PC Bluetooth
Figure 5: Service Icons for Windows XP
Name
Audio Gateway
Service Icons for Windows XP
Normal Connected Not Available*
Dial-up Networking
Fax
Headset
Network Access
PIM Item Transfer
PIM Synchronization
Public Folder
Serial Port
* Services may be unavailable because they are in use or because the necessary hardware is not installed.
18
User’s Guide
3.2 Basic Operations
1. Start Or Stop Bluetooth
To start Bluetooth: in the Windows system tray, rightclick the Bluetooth icon and select Start the Bluetooth Device.
The Bluetooth icon is blue in color with a white insert when
Bluetooth is running.
To stop Bluetooth: in the Windows system tray, right-click the Bluetooth icon and select Stop the Bluetooth Device.
The Bluetooth icon is blue in color with a red insert when
Bluetooth is stopped.
2. Create A Connection From The Bluetooth Icon In The
System Tray
In the Windows system tray, right-click the Bluetooth icon, select Quick Connect and then the Bluetooth service that you wish to use.
If this computer has created a connection to the desired type of service in the past, the options on the shortcut menu are:
The name(s) of any device(s) with which prior conn e c t i o n s t o t h i s t y p e o f s e r v i c e h a v e b e e n established. Select a name from the list to re-establish connection.
Other Devices…Select this option to search for additional devices that potentially provide the desired service, select a device from the list, and then click Connect.
If this computer has never created a connection to this type of service, the only option on the shortcut menu is “Find
19
PC2PC Bluetooth
Devices….” Select this option to search for devices that potentially provide the desired service, select a device from the list, and then click Connect.
3. Create A Connection Using The Bluetooth Setup Wizard
From the Folders pane of Windows Explorer, right-click
My Bluetooth Places and select Bluetooth Setup Wizard o r
In Windows Explorer, with My Bluetooth Places selected, from the Bluetooth menu, select Bluetooth Setup Wizard o r
From the Windows system tray: right-click the Bluetooth icon and select Bluetooth Setup Wizard.
Follow the wizard’s on-screen instructions.
4. Create A Connection From Entire Bluetooth Neighborhood
20
From Windows Explorer:
I n t h e F o l d e r s p a n e , s e l e c t E n t i r e B l u e t o o t h
Neighborhood, right-click a device name and select “Connect …” the desired service.
o r
I n t h e F o l d e r s p a n e , e x p a n d E n t i r e B l u e t o o t h
User’s Guide
Neighborhood, select a device, and then, in the right pane, right-click a service provided by that device and select “Connect to…”
MSI Reminds You...
Only available services are displayed in the menus.
5. Find Bluetooth Devices
Search for Devices looks for Bluetooth devices in the vicinity and displays the devices that it finds in My Bluetooth
Places.
To start a search for devices, in the Folders pane of My
Bluetooth Places, select Entire Bluetooth Neighborhood, and then, from the Bluetooth menu, select Search for Devices.
MSI Reminds You...
The Bluetooth menu is only visible when My Bluetooth
Places is active.
Periodic Search for Devices
Bluetooth can be configured to automatically search for devices on a regular basis (Bluetooth Configuration Panel >
Discovery tab).
One of the advantages of Bluetooth is the mobility that the wireless connections allow. However, mobility means that devices may move in or out of connection range during the time between the automatic updates performed by Bluetooth.
To be certain that the displayed list of devices in the neighborhood is current, or if automatic periodic inquiry is not enabled, force an update of the device list using the technique described in Search for Devices, above.
21
PC2PC Bluetooth
Some devices within connection range may not show up in the list of devices found because:
Your device is configured to report only specific types or classes of devices (Bluetooth Configuration Panel
> Discovery tab, on your device).
The unlisted device is configured to be non-discoverable (Bluetooth Configuration Panel > Accessibility tab, on the unlisted device).
6. Find A Service
The process of determining the services that a device provides is called Service Discovery.
To initiate a Service Discovery, in the Folders pane of My
Bluetooth Places, right-click a device name and select Discover Available Services from the shortcut menu.
Bluetooth services are those things that this computer can do for remote Bluetooth devices. For example, if this computer allows a remote Bluetooth device to send a fax using a fax modem that is physically attached to this computer, then this computer is providing the Bluetooth fax service.
Some services are hardware dependant; this computer cannot provide the fax service unless it has a physical fax modem, for example.
Some Bluetooth services use virtual “hardware.” The
Bluetooth Serial Port service, for example, does not use a physical port on this computer. Instead, it creates virtual serial ports that Windows applications can see and use as if they were actual physical ports.
Each Bluetooth service that this computer is capable of providing can be started automatically when Bluetooth starts.
Each service can be setup to require security measures before
22
User’s Guide allowing a remote Bluetooth device to connect.
Bluetooth services require a Bluetooth application on the remote device; services and applications usually have coinciding names; i.e., there is a Bluetooth Fax Service and a
Bluetooth Fax Application.
The services supported by Bluetooth are:
Bluetooth Serial Port—a wireless connection between two devices. This connection can be used by applications as though a physical serial cable connected the devices.
Dial-up Networking—allows a device to use a modem that is physically attached to another Bluetooth device.
Fax—allows a device to send a fax using a remote
Bluetooth cell phone, modem, or computer.
File Transfer—allows a device to perform file system operations on another Bluetooth device; browse, open, copy, etc.
Headset—allows a Bluetooth headset to be used as the audio input/output mechanism for another Bluetooth device, such as a computer or cell phone.
PIM Item Transfer—allows two Bluetooth devices to exchange Personal Information Manager data such as business cards, calendar items, email messages, and notes.
PIM Synchronization—allows two Bluetooth devices to synchronize Personal Information Manager data.
Network Access—allows a device to access a Local
Area Network via a second Bluetooth device that is physically connected to the network or allows a remote device to become part of an ad hoc network provided by the Bluetooth server.
Audio Gateway—allows the microphone/speakers on
Bluetooth device (typically a computer) to be used as
23
PC2PC Bluetooth the audio input/output mechanism for a remote
Bluetooth device, such as a cell phone.
All Bluetooth servers do not necessarily provide all of these services. For example, network gateways may provide only the Network Access service.
7. Bluetooth Connection Status
The Bluetooth Connection Status dialog box displays information about the state of a connection and provides a means to disconnect an active connection.
Display the Connection Status dialog box: i n M y
Bluetooth Places, from the Folders pane, select a device, and then, in the right pane of My Bluetooth Places, right-click a service name and select Status from the shortcut menu.
The Information provided is:
Status: “Connected” or “Not Connected”
Device Name: the name of the device to which this computer is connected.
Duration: the length of time that this connection has been established, displayed in hours, minutes and seconds.
Depending on the service, the connection may time out (automatically disconnect) after a specific period of inactivity.
Activity: the number of bytes sent and received over the connection.
Signal Strength: a graphic indicator that ranges from
Too Weak through Good to Too Strong.
MSI Reminds You...
To change the power transmission level of this
24
User’s Guide computer: from the Bluetooth Configuration Panel,
Hardware tab, click the Advanced button, and then change the setting in the Maximum Power Transmission drop-down list. The Advanced button is not available in all countries.
The controls in the Bluetooth Connection Status dialog box are
Properties button: displays the Bluetooth Properties dialog box for this connection.
Disconnect button: closes this connection.
Close button: closes the Bluetooth Connection Status dialog box.
8. Send To Bluetooth
This feature is used to send information to another Bluetooth device. Data types include:
Files from Windows Explorer
Documents from Microsoft Office applications, including:
Word
Excel
Access
PowerPoint.
Microsoft Outlook items, including:
Contacts
Appointments
Tasks
Messages
Notes.
25
PC2PC Bluetooth
To use Send to Bluetooth
1. In the application: a) Windows Explorer—select one or more files to be transferred. Folders cannot be transferred.
b) Microsoft Office—only the document in the active window can be transferred.
c) Microsoft Outlook—select one or more items to be transferred.
2. From the application’s File menu, select Send To, and then select Bluetooth from the shortcut menu.
3. Select a device from the shortcut menu to send the data o r
Select Other..., choose a device from the list, and then click OK to send the data.
3.3 Configure Bluetooth
1. Access the Bluetooth Configuration Panel
The Bluetooth Configuration Panel provides access to settings for Bluetooth services, client applications, hardware, security, discovery, accessibility, default paths, event notification and other Bluetooth related items.
To Open the Bluetooth Configuration Panel
From the Windows Control Panel, select Bluetooth
Configuration o r
In the Windows System Tray, right-click the
Bluetooth icon, and select Advanced Configuration from the shortcut menu.
26
User’s Guide
2. Bluetooth Services versus Bluetooth Applications
Bluetooth Services are services that this computer provides to remote Bluetooth devices. The Bluetooth services on this computer are referred to collectively in the Bluetooth configuration panel as “Local Services.”
Bluetooth Applications are software applications on this computer that allow this computer to use the Bluetooth services that are provided by remote devices. The Bluetooth applications on this computer are referred to collectively in the Bluetooth configuration panel as “Client Applications.”
Bluetooth Services and Bluetooth Applications usually have coinciding names; e.g., there is a File Transfer service and a
File Transfer client application.
How this computer provides a service to remote devices is configured on the Local Services tab of the Bluetooth configuration panel.
How this computer uses a service that is provided by a remote device is configured on the Client Applications tab of the Bluetooth configuration panel.
3. Bluetooth Exchange Folder
This is the highest-level directory on this computer to which a remote Bluetooth device has access.
Devices that have been granted access to this computer’s
Bluetooth Exchange Folder also have access to all sub-folders contained within that folder and all files in those sub-
27
PC2PC Bluetooth folders.
MSI Reminds You...
The Bluetooth Exchange Folder is shared by the PIM
Item Transfer and the File Transfer services and can be configured from the Properties page of either of those services. When the Bluetooth Exchange Folder is reconfigured for either of these services, the other service will be updated to use the new location.
4. General Configuration Settings
General Configuration Settings
The settings on the General tab of the Bluetooth Configuration Panel determine information that is displayed to remote devices.
28
User’s Guide
Identity
Computer Name-enter a unique name to identify this computer to other Bluetooth devices in the vicinity; this field cannot be left blank.
Computer type-select either Desktop or Laptop from the shortcut menu to set the type of icon remote devices will use to represent this computer.
5. Bluetooth Applications
* Overview
Some built-in Bluetooth applications provide full functionality for a specific task, such as locating other Bluetooth devices or synchronizing two Personal Information Managers.
Other built-in Bluetooth applications provide a way for standard Windows applications to accomplish their tasks wirelessly. For example, a Bluetooth application may create a wireless serial connection between computers or provide wireless access to the Internet.
The difference between Bluetooth Applications and
Bluetooth Services
Bluetooth Applications are software programs on this computer that allow this computer to use the
Bluetooth services that are provided by other devices.
In the Bluetooth configuration panel, these programs are referred to collectively as “Client Applications.”
Bluetooth Services are software programs on this computer that provide a service to other devices. In the Bluetooth configuration panel, these applications are referred to collectively as “Local Services.”
29
PC2PC Bluetooth
30
MSI Reminds You...
Client Applications and Local Services usually have coinciding names; e.g., there may be a Fax service and a Fax application.
* General Configuration
All of the built-in Bluetooth applications allow you to rename the application and to require a secure connection when using the application.
To access the configuration properties page for a builtin Bluetooth application
In the Windows system tray, right-click the
Bluetooth icon and select Advanced Configuration from the shortcut menu o r
From the Windows control panel select Bluetooth
Configuration o r
F r o m W i n d o w s E x p l o r e r , r i g h t - c l i c k E n t i r e
Bluetooth Neighborhood and select Properties from the shortcut menu.
In the Bluetooth configuration panel, Client Applications tab, highlight the application to be configured, and then click Properties (or double-click the application).
* Human Interface Device
Overview
The Human Interface Device (HID) Application allows this computer to wirelessly use one or more remote Bluetooth
HIDs as input/output devices.
User’s Guide
For example, the HID Application allows this computer to use a Bluetooth keyboard and a Bluetooth mouse.
Create a Bluetooth HID connection
MSI Reminds You...
Some HIDs have multiple modes. Before establishing a connection, be sure the HID is in the desired mode.
For example, in the case of an HID that can function as both a mouse and a laser pointer, be sure the mode switch is set to “Mouse” before attempting to connect.
Open a connection to a Bluetooth Human Interface Device using one of these techniques:
From My Bluetooth Places
Using the Bluetooth Setup Wizard
Once an HID connection is established, that connection will persist. If the computer is shut down, when the computer is turned on again the connection will re-establish automatically.
MSI Reminds You...
HIDs usually have a button, which is sometimes difficult to find, that must be pressed before other Bluetooth devices can locate the HID. Even after the button is pressed, the HID can only be discovered for a limited time, and then the button must be pressed again. The time period can be as short as 30 seconds or as long as
180 seconds.
Read the documentation that accompanies the HID before you attempt to connect to the device.
31
PC2PC Bluetooth
Close an HID connection
Under normal circumstances, there is no reason to close an
HID connection; once established the connection is maintained automatically, even during the power off and power on processes.
If, for some reason, the connection must be closed: from My
Bluetooth Places, right-click the service name and select
Disconnect.
When an HID connection is closed manually by the operator, the connection’s “persistence” is broken. The connection must be re-established manually, after which the connection will again persist until broken manually.
C o n f i g u r e
No configuration is necessary.
* Audio Gateway
Overview
The Audio Gateway Application allows a remote Bluetooth device to use this computer’s microphone and speakers as the remote device’s audio input and output devices.
Open a connection to the Audio Gateway service that is provided by another Bluetooth device using one of these techniques:
Windows system tray, Bluetooth icon
From My Bluetooth Places
Using the Bluetooth Setup Wizard
32
User’s Guide
Close an audio gateway connection:
If the connection was established via the Bluetooth icon in the Windows system tray; click the Bluetooth icon, select
Quick Connect, Audio Gateway and then select the device that is providing the service (active connections have a checkmark in front of them).
o r
No matter how the connection was created, in My Bluetooth
Places, right-click the service name and select Disconnect.
Configure
The Bluetooth Configuration Panel > Client Applications >
Audio Gateway > General tab provides options to configure:
The application name—to change it, highlight the existing name and enter the new name.
Enable or disable secure connection. To enable secure connection, place a checkmark in the box.
33
PC2PC Bluetooth
* Bluetooth Serial Port
Overview
The Bluetooth Serial Port application allows this computer to establish a wireless serial connection with a remote
Bluetooth device.
The applications on both this computer and the remote device must be configured to send and receive data to and from the respective communications port (COM port) assigned to the Bluetooth serial port. The wireless serial connection may then be used by the applications as though a physical serial cable connected the devices.
Create a Bluetooth Serial Port connection
Establish a connection using one of these techniques
Windows system tray, Bluetooth icon
From My Bluetooth Places
Using the Bluetooth Setup Wizard
Close a Bluetooth Serial Port connection
If the connection was established via the Bluetooth icon in the Windows system tray; click the Bluetooth icon, select Quick Connect, Bluetooth Serial Port and then select the device that is providing the service
(active connections have a checkmark in front of them).
o r
No matter how the connection was created, In My
Bluetooth Places, right-click the service name and select Disconnect.
C o n f i g u r e
The Bluetooth Configuration Panel > Client Applications >
34
User’s Guide
Bluetooth Serial Port > General tab provides options to configure:
The application name—to change it, highlight the existing name and enter the new name.
Enable or disable secure connection. To enable secure connection, place a checkmark in the box.
The communications port (COM port) to be used.
MSI Reminds You...
Unless you have a specific reason to do so, DO NOT
CHANGE the default COM Port setting.
* Dial-up Networking
Overview
The Bluetooth Dial-up Networking application allows this computer to use a modem that is physically connected to a remote device to access the Internet, log on to a remote network.
Open a connection to the Dial-up Networking service that is provided by another Bluetooth device using one of these techniques:
Windows system tray, Bluetooth icon
From My Bluetooth Places
Using the Bluetooth Setup Wizard
After the Bluetooth dial-up networking connection is established it can be used the same way as any other networking connection. For example, you can open a browser and explore the World Wide Web, if the remote computer has
Internet access.
35
PC2PC Bluetooth
36
Close a Dial-up Networking connection
If the connection was established via the Bluetooth icon in the Windows system tray; click the Bluetooth icon, select Quick Connect, Dial-up Networking and then select the device that is providing the service
(active connections have a checkmark in front of them).
o r
No matter how the connection was created, In My
Bluetooth Places, right-click the service name and select Disconnect.
C o n f i g u r e
The Bluetooth Configuration Panel > Client Applications >
Dial-up Networking > General tab provides options to configure:
The application name—to change it, highlight the existing name and enter the new name.
Enable or disable secure connection. To enable secure connection, place a checkmark in the box.
User’s Guide
The Bluetooth virtual device to be used.
MSI Reminds You...
Unless you have a specific reason to do so, DO NOT
CHANGE the default Bluetooth device or alter the device’s configuration.
* Fax
Overview
The Bluetooth Fax service allows this computer to send a fax using a Fax/Modem that is physically connected to a remote device.
To Send a Fax
1. Open a connection to the Fax service that is provided by another Bluetooth device, using one of these techniques:
Windows system tray, Bluetooth icon
From My Bluetooth Places
Using the Bluetooth Setup Wizard
2. Open or create the document to be faxed and select the
“Print,” “Send to Fax Recipient” or similar command that is available in most applications.
Close a Fax Connection
Fax connections close automatically when the Fax transmission is complete.
C o n f i g u r e
The Bluetooth Configuration Panel > Client Applications >
Fax > General tab provides options to configure:
The application name—to change it, highlight the existing name and enter the new name.
37
PC2PC Bluetooth
Enable or disable secure connection. To enable secure connection, place a checkmark in the box.
* Headset
Overview
The Headset application allows this computer to use a
Bluetooth headset (or any other device that offers the
Bluetooth headset service) as the audio input and output device for this computer.
Possible uses include:
If this computer has on-board telephone hardware, a
Bluetooth headset might be used as the audio input/ output device to make/receive telephone calls.
If this computer has voice recognition capabilities, a
Bluetooth headset might be used as the audio input device.
Any other scenario that requires audio input/output can potentially take advantage of a Bluetooth headset to replace a hardwired microphone and/or speakers.
MSI Reminds You...
Windows 98 limitation—
Windows 98 cannot convert audio files with the extension m3u (e.g., myfile.m3u) into the Pulse Code Modulation (PCM) audio format used by Bluetooth headsets.
38
User’s Guide
Create a Headset connection
Establish a connection using one of these techniques:
Windows system tray, Bluetooth icon
From My Bluetooth Places
Using the Bluetooth Setup Wizard
MSI Reminds You...
Most Bluetooth headsets “ring” when a connection is attempted; answer the ring to complete the connection and begin using the headset as the audio input/output device for this computer.
Close a Headset connection
If the connection was established via the Bluetooth icon in the Windows system tray; click the Bluetooth icon, select Quick Connect, Headset and then select the device that is providing the service (active connections have a checkmark in front of them).
39
PC2PC Bluetooth o r
No matter how the connection was created, in My
Bluetooth Places, right-click the service name and select Disconnect.
C o n f i g u r e
The Bluetooth Configuration Panel > Client Applications >
Headset > General tab provides options to configure:
The application name—to change it, highlight the existing name and enter the new name.
Enable or disable secure connection. To enable secure connection, place a checkmark in the box.
* File Transfer
Overview
The Bluetooth File Transfer application allows this computer to perform file operations on the Bluetooth Exchange
Folder (and the folders and files it contains) of a remote device.
Copy to/from a remote device
In the Folders pane of Windows Explorer, from the Entire
Bluetooth Neighborhood branch, select a device and expand that branch to view the Bluetooth Exchange Folder of the remote device.
MSI Reminds You...
If “Public Folder” is not available, the remote device is not configured to allow remote file operations.
Use drag-and-drop to copy any file or folder contained in the
Public Folder of the remote device to the desired folder on
40
User’s Guide this computer.
You can also drag-and-drop files or folders from this computer to the Public Folder (and its sub-folders) of the remote device.
Other file operations
Right-click a file or folder in the remote device’s Public
Folder for a context sensitive menu. All potential menu options may not be available at all times.
Potential menu options include:
Open—opens the selected file on this computer, using the default application for this type of file.
Print—sends the selected file to this computer’s default printer.
Send To
3 ½ floppy (A)—the 3 ½ inch floppy drive on this computer
Bluetooth Exchange Folder—the Bluetooth Exchange
41
PC2PC Bluetooth
Folder on this computer.
Rename—applies only to empty folders; file names and the names of folders that contain objects cannot be changed using this technique.
Cut, Copy, Paste, Delete, Refresh, View & New— standard Windows functions.
C o n f i g u r e
The Bluetooth Configuration Panel > Client Applications >
File Transfer > General tab provides options to configure:
The application name—to change it, highlight the existing name and enter the new name.
Enable or disable secure connection. To enable secure connection, place a checkmark in the box.
* Network Access
Overview
The Bluetooth Network Access application makes it possible for this computer:
To connect to a Local Area Network via a physical c o n n e c t i o n o n a r e m o t e B l u e t o o t h d e v i c e .
o r
To connect to an ad hoc network provided by a remote Bluetooth device.
The type of network connection that is available is determined by the configuration of the remote Bluetooth device.
Create a Network Access connection
Establish a connection using one of these techniques
Windows system tray, Bluetooth icon
From My Bluetooth Places
Using the Bluetooth Setup Wizard
42
User’s Guide
Close a Network Access connection
If the connection was established via the Bluetooth icon in the Windows system tray; click the Bluetooth icon, select Quick Connect, Network Access and then select the device that is providing the service (active connections have a checkmark in front of them).
o r
No matter how the connection was created, In My
Bluetooth Places, right-click the service name and select Disconnect.
C o n f i g u r e
The Bluetooth Configuration Panel > Client Applications >
Network Access > General tab provides options to configure:
The application name—to change it, highlight the existing name and enter the new name.
Enable or disable secure connection. To enable secure connection, place a checkmark in the box.
* PIM Synchronization
Overview
The PIM Synchronization Application is used to synchronize the Personal Information Manager (PIM) database of this computer with the PIM database of a remote Bluetooth device.
The supported PIMs are:
Microsoft Outlook
Microsoft Outlook Express
Lotus Notes.
The supported data types are:
43
PC2PC Bluetooth
Business cards
Calendar items
Email (with or without attachments)
Notes.
Configure PIM Synchronization
The Bluetooth Configuration Panel > Client Applications >
PIM Synchronization > General tab provides options to configure:
The application name—to change it, highlight the existing name and enter the new name.
Enable or disable secure connection. To enable secure connection, place a checkmark in the box.
The PIM items to be synchronized and the PIM on this computer with which those items should be synced.
MSI Reminds You...
If synchronization is enabled for a specific item type, but is not enabled for that item type on the remote device, synchronization WILL NOT take place for that item.
The data item types which can be synchronized are:
Business cards
Calendar items
Email (with or without attachments-see below)
Notes
Possible synchronization options for each of these data item types include:
Do Not Synchronize-this item type will not be synchronized
44
User’s Guide
Synchronize Microsoft Outlook-this item type will be synced with its matching entry in Microsoft
Outlook, regardless of the PIM that contains this entry on the remote device. If a matching Outlook entry does not exist, it will be created
Synchronize Outlook-Express-this item type will be synced with its matching entry in Express, regardless of the PIM that contains this entry on the remote device. If a matching Express entry does not exist, it will be created
Synchronize Lotus Notes-this item type will be synced with its matching entry in Lotus Notes, regardless of the PIM that contains this entry on the remote device. If a matching Notes entry does not exist, it will be created.
MSI Reminds You...
All choices are not available for all items. For example,
“Note” items can only be synchronized in Microsoft
Outlook, therefore Lotus Notes and Outlook Express do not appear as options in the “Notes” item shortcut menu.
Personal Information Managers that are not installed on this computer do not appear as options in the shortcut menus.
Email attachments. The only option is include or do not include attachments with email that is sent or received on this computer using this service.
45
PC2PC Bluetooth
* PIM Item Transfer
Overview
The Bluetooth PIM Item Transfer application allows this computer to send and receive Personal Information Manager items to-and-from a remote Bluetooth device. Item transfer can be accomplished several ways:
To send, receive or exchange business cards:
1. From Windows Explorer, My Bluetooth Places, rightclick the PIM Item Transfer service on a remote device and select the appropriate option.
o r
In the Windows system tray, right-click the Bluetooth icon, select Quick Connect > Business Card Exchange, select a device from the list, select the appropriate option from the shortcut menu, and then click OK.
2. From Windows Explorer, My Bluetooth Places, highlight the PIM Item Transfer service on a remote device, and then, from the Bluetooth menu on the Windows menu bar, select the appropriate action.
In addition to the business card options listed above, you can also send Notes (*.vnt), Email (*.vmg) and
Calendar (*.vcs) items from this menu.
3. From within a supported Personal Information
Manager, select one or more items and then, from the
PIM’s File menu, select Send to Bluetooth.
Whether sent items are accepted by the remote device is determined by how the remote device’s PIM Item Transfer service is configured.
46
User’s Guide
Close a PIM Item Transfer Connection
This application closes the open connection automatically when its task is complete.
Configure PIM Item Transfer
The Bluetooth Configuration Panel > Client Applications >
PIM Item Transfer > General tab provides options to configure:
The application name—to change it, highlight the existing name and enter the new name.
Enable or disable secure connection. To enable secure connection, place a checkmark in the box.
How your business card is handled when it is requested by a remote device. The Send My Business Card options are:
Choose a business card as needed-each time a remote device requests your business card you must select a card
47
PC2PC Bluetooth from your PIM. If you ignore the request the remote device will receive a time-out notice.
Always send the same business card-when this option is selected a dialog appears that allows you to set a default business card, which will be sent automatically when requests are received.
Where to store received business cards. The Received Business Cards options are:
Microsoft Outlook
Outlook Express
Lotus Notes
MSI Reminds You...
The selected Received Business Cards option does not influence the settings on other PIM-related property pages.
For example, even if the PIM Item Transfer service business card option on this computer is configured to
“Do Not Accept,” the PIM Item Transfer application will still accept business cards that the application has specifically requested via its “Receive” or “Exchange” functions.
Email attachments. The only option is include or do not include attachments with email that is sent or received on this computer using this service.
* Printer
Overview
The Bluetooth Printer application allows this computer to use a Bluetooth printer.
48
User’s Guide
Once a Bluetooth printer has been properly installed it can be used from this computer in the same way as any other printer would be.
C o n f i g u r e
The Bluetooth Configuration Panel > Client Applications >
Printer > General tab provides options to configure:
The application name—to change it, highlight the existing name and enter the new name.
Enable or disable secure connection. To enable secure connection, place a checkmark in the box.
Install a Bluetooth Printer
Option One:
1. Perform a search for devices and then, from Entire
Bluetooth Neighborhood, right-click a Bluetooth printer, select Add Printer from the shortcut menu and follow the on-screen instructions.
2. When the wizard asks you to select a printer make and model, do so.
If your printer is not in the list of options, click Have
Disk…, insert the driver disk for the printer, and then navigate to the drive and directory that contains the driver initiation file (*.inf) for the printer.
3. To complete the installation, follow the on-screen instructions.
Option Two:
1. From the Windows Control Panel, select Printers >
Add Printer > Next > Local printer > Next
2. On the Select the Printer Port screen of the wizard: a) Select Create a new port b) In the Type shortcut menu, select Bluetooth
49
PC2PC Bluetooth
Printer Port, and then click Next
3. On the next screen, select the printer by name, and then click Connect.
4. Install the driver: when asked to select a printer make and model, do so.
If your printer is not in the list of options, click Have
Disk…, insert the driver disk for the printer, and then navigate to the drive and directory that contain the driver initiation file (*.inf) for the printer.
5. To complete the installation, follow the on-screen instructions.
To delete a printer, Click Start > Settings > Printers, rightclick the printer to be deleted, and then select Delete from the shortcut menu.
6. Bluetooth Services
Common Configuration Settings
These properties can be set individually for each Bluetooth service:
Service Name-the default name of each service can be changed.
Secure Connection-requires that remote devices provide proof of identity and that all data be encrypted.
Startup Automatically-starts the service automatically when Bluetooth is started.
Notifications-provides visual and/or audio notification that a remote device is attempting to connect
(or has connected) to a service on this computer.
50
User’s Guide
* Notifications
Overview
There are three types of notification:
Authentication request, also called a PIN code request—this notification appears automatically in a balloon over the Windows system tray if a Personal
Identification Code is required before a connection can proceed. An audio file can also be associated with the notification.
Authorization request, also called a connection request—this type of notification can be visual, audio, or both. It notifies you of attempts to access a
Bluetooth service on this computer; the connection will not proceed until you click the balloon that appears over the Windows system tray. If the notification balloon is ignored, the connection request will time out and fail.
Notification only—this type of notification does not effect access in any way; it is solely for information purposes to let you know that a connection has been established.
Example
Both Authentication and Authorization request notifications are controlled by whether Secure Connection is enabled for an individual service.
An example of how notifications might work when a remote device attempts to access a service on this computer, if all notifications are enabled:
1. Authentication: a balloon notification (audio optional) appears to prompt for a PIN code. If the PIN code does not match the code entered on the remote device,
51
PC2PC Bluetooth the connection will not be allowed. Once the remote device has been authenticated this notification will not appear again, unless the paired relationship is broken and the devices must repair.
2. Authorization: a balloon notification appears and/or a sound file provides audio notification that a remote device is attempting to access a Bluetooth service on this computer. Click the balloon to proceed. A dialog box appears that offers the option of letting the connection proceed this time only or to always allow this particular remote device to use the service it is attempting to access.
3. Once a connection has been authorized, an additional visual and/or audio notification may appear (if enabled). This notification is for information only to inform the operator that a connection has been established.
After two devices are paired (step 1, above), the authentication notification will no longer appear when a connection is attempted.
If “Always allow…” is enabled during the authorization process (step 2, above), the authorization notification will not appear on future connection attempts.
Connection notification (step 3, above) only happens if it has been enabled on the Notifications tab of the individual service being accessed.
Service Access Notification
“Notifications” lets you associate a sound (Windows *.wav
file) and/or a visual indication with access attempts by remote devices.
A different notification sound can be associated with each
52
User’s Guide local Bluetooth service.
Associate a sound with service access
From the Bluetooth Configuration Panel, Local Services tab:
1. Double-click a service name and then select the Notifications tab.
2. Check the desired options; visual and sound may both be selected for a single event.
3. Choose a sound; click the Browse button and navigate to the sound file (*.wav) to be used for notification.
To preview the sound file, click the play ( ) button.
4. Click OK to close the service’s property dialog box.
* Audio Gateway
The Bluetooth Audio Gateway service allows this computer to use a remote Bluetooth device’s microphone and speakers as this computer’s input and output devices.
For example, if this computer has voice recognition capabilities, a Bluetooth headset might be used as the audio input device.
Hardware Requirements
The Bluetooth radio on both this computer and the remote device must support audio.
The remote device handles both audio input and output for this computer; therefore, this computer does not require a sound card, microphone, or speakers.
Configure the Audio Gateway Service
From the Windows system tray, right-click the Bluetooth icon, select Advanced Configuration > Local Services, and
53
PC2PC Bluetooth then double-click the Audio Gateway service.
Set the common configuration properties of the service, and then click OK.
* Bluetooth Serial Port
The Bluetooth Serial Port service allows a remote Bluetooth device to establish a wireless serial connection with this computer. The wireless serial connection may be used by applications as though a physical serial cable connected the devices.
To establish a Bluetooth Serial Port connection
The connection must be initiated from the remote device by the Bluetooth Serial Port application.
Determine the communications port being used by this computer for the Bluetooth Serial Port
In the Windows system tray, right-click the Bluetooth icon, select Advanced Configuration, and then the Local Services tab. The COM port assigned to this service is the last item in the Bluetooth Serial Port service row. Configure the application on this computer that will use this service to send its data to this COM.
Add a Bluetooth Serial Port
The Bluetooth Serial Port service has one pre-configured
Bluetooth Serial Port, but additional Bluetooth Serial Ports can be added as needed.
To add a port
1. From the Bluetooth Configuration Panel, Local Services tab, click Add Serial Service.
2. In the properties dialog box, modify the properties:
54
User’s Guide
3. Enter a unique name (less than 99 alphanumeric characters).
4. Select secure connection, if desired.
5. Select Startup Automatically, if desired
6. From the COM Port shortcut menu select a communications port that is not assigned to any other service.
7. Click OK.
To remove a Bluetooth Serial Port
From the Bluetooth Configuration Panel, Local Services tab, select the port to be removed and then click Delete.
MSI Reminds You...
The Delete button is only available when a Bluetooth
Serial Port is selected.
* Dial-up Networking Service
The Bluetooth Dial-up Networking service makes it possible for a remote Bluetooth device to use a modem that is physically connected to this computer. The remote device can then access the Internet or log on to a remote network.
Configure the Dial-up Networking service:
From the Windows system tray, right-click the Bluetooth icon, select Advanced Configuration > Local Services, and then double-click the Dial-up Networking service.
Select the physical modem to be used from the
Modems: shortcut menu.
55
PC2PC Bluetooth
Set the common configuration properties of the service, and then click OK.
56
User’s Guide
* Fax Service
The Fax service allows a remote Bluetooth device to send a
Fax via a modem that is physically attached to this computer.
Configure the Fax service:
From the Windows system tray, right-click the Bluetooth icon, select Advanced Configuration > Local Services, and then double-click the Fax service.
Select the physical modem to be used from the
Modems: shortcut menu.
Set the common configuration properties of the service, and then click OK.
* File Transfer Service
Overview
The File Transfer service allows this computer to perform file operations on the Bluetooth Exchange Folder (and the folders and files it contains) of a remote device.
Basic setup procedure
Right-click the Bluetooth icon and select Explore My
Bluetooth Places.
Configure Windows Explorer so that the Folders pane is visible (View > Explorer Bar > Folders).
In the Folders pane, select Entire Bluetooth Neighborhood and then, on the menu bar, select Bluetooth > Search For
Devices.
In the Folders pane, expand Entire Bluetooth Neighborhood to show the devices in the vicinity.
Copy to/from a remote device
In the Folders pane of Windows Explorer, from the Entire
57
PC2PC Bluetooth
Bluetooth Neighborhood branch, select a device and expand that branch to view the Bluetooth Exchange Folder of the remote device.
MSI Reminds You...
“Public Folder” is not available, the remote device is not configured to allow remote file operations.
Use drag-and-drop to copy any file or folder contained in the
Public Folder of the remote device to the desired folder on this computer.
You can also drag-and-drop files or folders from this computer to the Public Folder (and its sub-folders) of the remote device.
Other file operations
Right-click a file or folder in the remote device’s Public
Folder for a context sensitive menu. All potential menu options may not be available at all times.
Potential menu options include:
Open—opens the selected file on this computer, using the default application for this type of file.
Print—sends the selected file to this computer’s default printer.
Send To
3 ½ floppy (A)—the 3 ½ inch floppy drive on this computer
Public Folder on My Device—the Public Folder on this computer.
Rename—applies only to empty folders; file names and the names of folders that contain objects cannot
58
User’s Guide be changed using this technique.
Cut, Copy, Paste, Delete, Refresh, View & New— standard Windows functions.
* Headset Service
The Bluetooth Headset Service allows this computer to provide audio input/output for remote Bluetooth devices.
For example, if the remote device is a Bluetooth telephone, this computer’s microphone and speakers can be used as speakerphone input and output for that device.
MSI Reminds You...
Windows 98 limitation—
Windows 98 cannot convert audio files with the extension m3u (e.g., myfile.m3u) into the Pulse Code Modulation (PCM) audio format used by Bluetooth headsets.
Hardware Requirements
This computer must have a sound card, microphone, and speakers installed.
The Bluetooth radio on both on this computer and the remote device must support audio.
Configure the Headset Service
From the Windows system tray, right-click the
Bluetooth icon, select Advanced Configuration > Local Services, and then double-click the Headset service.
Set the common configuration properties of the service, and then click OK.
59
PC2PC Bluetooth
60
* Network Access
The Bluetooth Network Access service makes it possible for a remote Bluetooth device to use the Local Area Network connection that is physically attached to this computer.
After this computer has been configured to provide the Network Access service to other Bluetooth devices, it will not be able to use the Bluetooth Network Access service provided by another Bluetooth device without being re-configured.
Put another way, this computer cannot be both a Bluetooth
Network Access server and a Bluetooth Network Access client at the same time.
Setup for Windows 98SE & Windows Me
MSI Reminds You...
Internet Protocol routing software is required on Windows 98SE and Windows Me servers.
Install and configure the routing software as instructed by the software’s manufacturer.
* Configure the server:
1. From the Windows Control Panel, double-click the
Network icon.
2. On the Configuration tab, select TCP/IP-> Bluetooth
LAN Access Server Driver (scroll down if necessary).
3. Click Properties and select the IP Address tab.
4. Select Specify an IP address
5. Enter an IP Address (suggested value—192.168.1.1)
6. Enter a Subnet Mask (suggested value—255.255.255.
0 )
7. Click OK twice to close the dialog boxes and then click
User’s Guide
YES to restart the computer.
Setup for Windows 2000 and Windows XP
If Internet Connection sharing was previously enabled (before
Bluetooth utility was installed) it must be disabled and then re-enabled before the Bluetooth network adapter can use it.
1. From the Windows system tray, right-click the
Bluetooth icon and select Advanced Configuration from the shortcut menu.
2. In the Bluetooth configuration panel, select the Local
S e r v i c e s t a b , N e t w o r k A c c e s s a n d t h e n c l i c k
Properties....
3. From the Network Access, General properties page, in the Type of service shortcut menu, select “Allow other devices to access the Internet/LAN via this computer,
” and then click Configure Connection Sharing.
61
PC2PC Bluetooth
4. Right-click Local Area Connection, select Properties and then select the Sharing tab.
62
User’s Guide
5. Select Enable Internet Connection Sharing for this connection, click OK, and then click YES in the confirmation dialog box.
* Client Configuration
1. From the Windows system tray, right-click the
Bluetooth icon and select Network Access from the shortcut menu.
2. Select the device you want to connect and the server will accept the connection.
3. The Bluetooth icon will change to green if the connection is created.
* Server Configuration
1. From the Windows Control Panel, double-click the
Network icon. On the Configuration tab, select TCP/
IP and enable the Sharing Network option.
2. The home Internet must connect to the Bluetooth devices. Click OK and the client will be able to connect.
* PIM Item Transfer
Overview
The PIM Item Transfer service allows Personal Information Manager items to be transferred between this computer and a remote Bluetooth device.
Four data types are supported:
Business Cards
Calendar Items
Email Messages
Notes
Each data type can be saved in any of the supported and installed PIMs.
63
PC2PC Bluetooth
MSI Reminds You...
PIMs which are not installed on this computer will not appear in the shortcut menus.
When the PIM that is associated with an individual data type is changed on the PIM Item Transfer page, that data type is also changed for the PIM Synchronization service.
C o n f i g u r e
In addition to the configuration options common to all
Bluetooth services, this service also has settings that determine:
How business card requests are handled. The options are:
Never send my business card—ignore the request
Choose a business card as needed—when prompted, select a business card to be sent to the requester.
Always send the same business card—when a request is received always send the same business card. When this option is selected, a dialog box appears from within which an installed Personal
Information Manager (if more than one is installed on this computer) and an existing business card can be selected.
Previously sent business cards—once a card is selected using the “Always send the same business card” option, above, that card will be added to the shortcut menu as an option.
MSI Reminds You...
Previously sent business card additions to the menu
64
User’s Guide are limited to ten, after which the oldest contact will be replaced.
Where to store inbound data items, on an individual basis. Options include (not all options apply to all items):
Do Not Accept
Any of the installed PIMs on this computer
Save to Folder
The Bluetooth Exchange Folder location—the directory on this computer where inbound items that are not to be saved in a PIM will be kept.
MSI Reminds You...
This is also the folder where the File Transfer service stores inbound items. If this folder is reconfigured here, it will also be reconfigured in that service automatically.
Whether to send/receive attachments with email.
Check or clear this option, as appropriate.
Close a PIM Item Transfer connection
PIM Item Transfer connections close automatically when the data transfer is complete.
Default Business Card Selection
When the “Always send the same business card” option is selected, a dialog box appears to allow the selection of a default business card.
The first time the dialog box appears it provides a way to choose the Personal Information Manager that stores the default business card. Click the down-arrow in the PIM short-
65
PC2PC Bluetooth cut menu and select the PIM to be used.
On subsequent appearances of this dialog box, the PIM selection option is not available.
Change the selected PIM
On the PIM Item Transfer properties page, “Received items” section, there is a Business Cards shortcut menu. When a
PIM was selected during initial setup the selected item in this menu was set to the same PIM. To change the PIM used for the default business card, open this shortcut menu and select a new PIM.
MSI Reminds You...
A new default business card must be selected from the database of the newly selected PIM.
Choose a default business card
1. In the Select a Bluetooth Business Card dialog box that appears when “Always send the same business card” is selected, highlight the card.
MSI Reminds You...
Once a card is highlighted, if you “hover” the mouse pointer over that selection, a balloon appears with additional information about that contact.
2. Click OK to choose a highlighted business card and return to the PIM Item Transfer Properties page. The chosen contact now appears in, and is selected in, the
66
User’s Guide
“Business card requests” shortcut menu.
If the “Always send the same business card” option is selected again, and a different contact chosen, the properties page will display both contacts in the shortcut menu.
MSI Reminds You...
In addition to the default menu options, the shortcut menu can hold up to ten contact names.
* PIM Synchronization
The PIM Synchronization service can be used by a remote device to synchronize its Personal Information Manager
(PIM) database with the PIM database of this computer..
Four data types are supported:
Business cards
Calendar items
Email messages
Notes.
Whether an individual item is accepted and where it is stored, when accepted, is configured in the PIM Item Transfer service.
If that service is not configured to store a particular data type in Outlook, then that data type cannot be synchronized.
MSI Reminds You...
Data types that will be synchronized must be saved in the PIM database (this is configured in the PIM Item
Transfer service); otherwise, that data type will not be available for selection (it will be grayed out) in the
PIM Synchronization configuration settings.
67
PC2PC Bluetooth
Microsoft Outlook permits duplicate entries, so all duplicates may not be exchanged in the synchronization process.
MSI Reminds You...
Only Outlook’s default contacts folder is synchronized.
Items in sub-folders are not synchronized. Items that are moved from the default folder to a sub-folder will appear to have been deleted the next time synchronization takes place.
7. Hardware Settings
The Hardware tab of the Bluetooth Configuration Panel provides basic information about the Bluetooth hardware installed on this computer and access to the Advanced Settings dialog box, if required:
Devices:
Name: the name of the device, e.g., MSI Bluetooth
Device
Type: the type of device, e.g., USB.
Device Properties:
Device status: indicates that the device is operating properly or that there is a problem/conflict.
Manufacturer: the name of the company that manufactured the device selected in the Devices section of this dialog box.
Firmware Revision: the manufacturer’s firmware version number.
Device Address: the Bluetooth Device Address
(BDA or BD_Addr) assigned to this device when it was manufactured.
68
User’s Guide
H C I Ve r s i o n : t h e v e r s i o n n u m b e r o f t h e
Bluetooth Specification that the Host Controller
Interface complies with.
HCI Revision : the revision number of the
Bluetooth Specification that the Host Controller
Interface complies with.
L M P Ve r s i o n : t h e v e r s i o n n u m b e r o f t h e
Bluetooth Specification that the Link Manager
Protocol complies with.
LMP Sub Version: the subversion number of the
Bluetooth Specification that the Link Manager
Protocol complies with.
The Advanced button: displays the Advanced Settings dialog box, which allows you to select the country code and transmission power settings. This option is not available on all systems.
* Advanced Settings
When available, this dialog box is reached from the Hardware tab of the Bluetooth Configuration Panel.
MSI Reminds You...
Depending on the country in which the hardware is sold and/or in which it will be used, the Advanced button may not be present.
From this dialog box you can set the:
Country Code:
North America, Europe (except France), and Japan
69
PC2PC Bluetooth
France and China
Maximum Transmission Power:
High
Medium
Low.
Click Apply to implement the changes. A dialog box appears with notification that the Bluetooth device attached to this computer must be reset before the change(s) will take effect.
Click Yes to reset the Bluetooth device now—all open
Bluetooth connections will be closed.
Click No to save the changes—the changes will be applied the next time the Bluetooth device is reset or restarted.
8. Accessibility Settings
The Accessibility tab of the Bluetooth Configuration Panel lets you specify whether remote devices may access this computer, which remote devices have access, and whether an audio warning is played when a Personal Identification
Number (PIN code) is required.
Allow other devices to discover this computer
Select “Let other Bluetooth devices discover this computer” to permit remote Bluetooth devices to find and report this computer.
If “Allow No devices” (below) is selected, this option is not available.
Control the types of devices that are allowed to connect to this computer
From the “Devices allowed to connect to this computer” shortcut-menu, select:
No devices—no remote devices are permitted to ini-
70
User’s Guide tiate a connection with this computer. However, this computer can still initiate connections with remote
Bluetooth devices.
All devices—all remote devices are permitted to connect to this computer.
Connections are subject to additional security restrictions, such as authentication and authorization, that may be required by the individual services provided by this computer.
Only paired devices—only devices that have been paired with this computer are allowed to connect to it.
Only devices listed below—only the listed devices a r e a l l o w e d t o c o n n e c t t o t h i s c o m p u t e r ( s e e
Accessibility, adding and deleting devices).
Choose an audio notification file
When Secure Connection is enabled for any of the Bluetooth
Services on this computer a PIN code is required before that service can be accessed. To chose a notification sound that will play when a remote device attempts to access a service that requires a secure connection, click Select audio file...
and select the sound (*.wav) file to be played.
Limit access to this computer to specific remote devices
From the Bluetooth Configuration Panel, Accessibility tab, in the Allow shortcut menu, select “Only devices listed below”.
Add a device to the list
1. Click Add Device
2. In the Devices with access... dialog box select the desired device(s) and click OK.
71
PC2PC Bluetooth
MSI Reminds You...
Multiple devices may be selected using SHIFT + click and/or CTRL + click.
Delete a device from the list
In the list of devices allowed to access this computer, select the device to be removed from the list, and then click Delete.
9. Discovery Settings
The settings on the Discovery tab of the Bluetooth Configuration Panel determine whether this computer looks for other
Bluetooth devices automatically, how often it looks and what type of devices it looks for.
Periodic Search for Devices
When “Look for other Bluetooth devices” is selected,
Bluetooth automatically searches for devices every X minutes. X is an whole number between 1 and 60. To change the time between auto inquiries, highlight the existing time and enter the new time.
MSI Reminds You...
When My Bluetooth Places is first opened it performs an initial automatic search for devices even if “Look for other Bluetooth devices” is not enabled.
Determine the devices that will be reported
Bluetooth can screen out devices that you do not need access t o .
The options are:
Report all Bluetooth devices
72
User’s Guide
Report only selected Bluetooth devices (see Discovery,
Adding Specific Devices and Discovery, Deleting Specific Devices).
Select the desired option from the drop-down list.
Discover Specific Devices
The type of device(s) that this computer looks for and reports when it is searching for other Bluetooth devices can be limited.
Limit the remote devices reported
Bluetooth can report only specific devices, specific class(es) of device(s), or specific type(s) of device(s) within a class.
Specific devices: an individual computer or Bluetooth cellular telephone are examples of specific devices.
Specific class of device: “computer” is an example of a class of devices
Specific type of device within a class: “laptop” is an example of a specific type of device within the “computer” class of devices.
The devices to be discovered can be mixed-and-matched; you can discover one or more specific devices, classes of devices and types of devices within a class at the same time.
Remove a device from the list of devices to be discove r e d
In the Bluetooth Configuration Panel, from the Discovery tab, select the device to be removed and click the Delete button.
MSI Reminds You...
If “Report only selected Bluetooth devices” is not selected the Delete button will not be available.
73
PC2PC Bluetooth
Temporarily override the discovery of specific devices
In the Bluetooth Configuration Panel, from the Discovery tab, select “Report all Bluetooth devices.” The specifically selected devices will be discovered along with all other devices.
To re-enable specific device discovery re-select “Report only selected Bluetooth devices.”
MSI Reminds You...
When all devices are deleted an error message will appear if “Report all Bluetooth devices” is not selected.
3.4 Security
1. Authentication
Authentication is used to verify identity; it requires a passkey or link key from the remote device. When a remote device attempts access, a visual and/or audio warning notifies the local operator.
If the notification is ignored, access is denied after a preset timeout.
When devices are “paired,” those devices automatically exchange a Link Key and Authentication is carried out without operator intervention.
2. Authorization
Authorization is Yes-or-No security that requires operator intervention to avoid having the connection time out and fail.
Authorization is limited to:
74
User’s Guide
Yes, you may connect (click the balloon to proceed)
No, you may not connect (ignore the balloon prompt and the connection will fail).
3. Bluetooth Device Identity
Every Bluetooth device has a unique Bluetooth Device Address (BDA) assigned to it during the manufacturing process.
This address cannot be changed by the end-user.
A device’s BDA is usually displayed in hexadecimal format;
00:D0:B7:03:2E:9F is a valid BDA.
Each Bluetooth device also has an operator-configurable, user-friendly name to help distinguish it from other devices.
The user-friendly name may be up to 99 alphanumeric characters in length and may contain spaces. My Personal Com-
puter is a valid user-friendly name.
4. Encryption
Encrypting data translates it into an unreadable format using a secret key or password. Decrypting the data requires the same key or password that was used to encrypt it.
5. Link Key
A unique, internally generated, access code based on a passkey, the Bluetooth Device Address and an internally generated random number.. Link Keys are generated automatically when devices Pair.
After a link key is generated, manual entry of the passkey is not required.
75
PC2PC Bluetooth
6. Pairing Devices
Pairing allows you to avoid entering access information each time a connection is attempted. Paired devices share a unique
Link Key, which they exchange each time they connect.
MSI Reminds You...
The mate of a pair always appears in My Bluetooth
Places, even if the mate is not turned on or is out of connection range.
Paired devices remain paired even when
One of the devices is not on
A service connection is interrupted or the service stopped
One or both devices are rebooted.
To Pair with another device
If Secure Connection is enabled, devices will pair automatically the first time they connect (a passkey must be successfully exchanged).
To pair with a device manually:
In the Folders pane of My Bluetooth Places, right-click a device, select Pair Device from the shortcut menu, and then follow the on-screen instructions.
Remove Pairing
In the Folders pane of My Bluetooth Places, right-click a paired device and select Unpair Device from the shortcut menu.
76
User’s Guide
7. Passkey
An alphanumeric string up to 16 characters in length. Passkeys are also called Personal Identification Numbers, or PIN codes.
A passkey may be required if the Secure Connection option is enabled for a Bluetooth service or application.
8. Secure Connection
A passkey or link key is required each time a connection is attempted.
All data exchanged over the Bluetooth connection is encrypted.
Depending on other configuration options, authorization may also be required.
9. Security Request Dialog Box
A Bluetooth passkey request and/or Bluetooth Authorization request balloon may appear over the Windows system tray when a connection is attempted if Secure Connection is enabled.
Click the balloon to proceed.
77
PC2PC Bluetooth
3.5 Troubleshooting
1. Cannot connect to a paired device
Paired devices are always displayed in My Bluetooth Places, even if the remote device is out of range or not powered up.
Verify that the remote member of the pair is within radio range, and powered up, and then attempt the connection again.
2. Cannot discover services on an unpaired remote device
The remote device may not be powered up or may be out of range.
Verify that the remote device is powered up.
Verify that the remote device is in Connectable mode
(Bluetooth Configuration Panel > Accessibility tab).
Perform a Search for Devices to verify that the device is within range.
3. Dial-up Networking service does not start
The Dial-up Networking service will not start unless a properly configured modem is attached to the server.
Verify that the modem is usable as a local device on the computer to which it is attached.
In the Bluetooth Configuration Panel, Local Services tab, double-click the Dial-up Networking service:
Click the down arrow in the Modem field and select the modem that will be used to dial out
Click the OK button
78
User’s Guide
Click the OK button to close the Bluetooth Configuration Panel.
4. Determine the Bluetooth Device Address (BDA) of my hardware device
In the Bluetooth Configuration Panel, on the Hardware tab, in the Devices section, select the device you want to determine the address of. In the Device Properties section of the dialog box, the fourth entry, Device Address, is the BDA of the selected Bluetooth device.
5. Determine the version of the Host Controller Interface (HCI)
In the Bluetooth Configuration Panel, on the Hardware tab, in the Device Properties section, the fifth entry provides
Bluetooth Specification compliance information for the Host
Controller Interface.
The sixth entry contains the Specification Revision information for the Host Controller Interface, if appropriate.
6. Determine the version of the Link Manager Protocol (LMP)
In the Bluetooth Configuration Panel, on the Hardware tab, in the Device Properties section, the seventh entry provides
Link Manager Protocol version number information.
The eighth entry contains the Link Manager Protocol subversion number information, if appropriate.
7. Find information about the Bluetooth hardware attached to
79
PC2PC Bluetooth
my computer
In the Bluetooth Configuration Panel, select the Hardware tab.
8. Internet Connection Sharing Does Not Work
This occurs because Internet Connection Sharing was enabled when Bluetooth was installed (this is a Microsoft Windows behavior and is considered proper operation).
To resolve the “problem”:
1. Disable Sharing for the Ethernet adapter: a) Windows Control Panel > Network and Dial-up Connections b) Right-click “Local Area Connection,” select
Properties, and then select the Sharing tab.
c) Clear (uncheck) the box for “Enable Internet Connection Sharing for this connection” and click OK.
2. Re-enable Sharing for the Ethernet adapter; repeat
Step 1.c.), and select (check) the sharing box.
If offered an option to select an adapter, select “Bluetooth network adapter.” (This option will not appear unless more than one adapter is available.)
If asked to reboot the computer, do so.
9. Test a Network Access connection
If the client is hardwired to the LAN, unplug the hardwired connection to ensure that the test checks the wireless connection rather than the hardwired connection.
If the server has access to the Internet, open a browser on the client and connect to the World Wide Web.
80
User’s Guide
You may also Ping the server from the DOS prompt.
10. Unknown Port message when using a Bluetooth Serial
Port
The “Unknown Port” error message usually means an attempt was made to connect a port that was in use.
Additional Bluetooth Serial Ports can be added if they are required.
11. Bluetooth Headset Doesn’t Always Function Under WIN
98
Windows 98 cannot convert audio files with the extension m3u (e.g., myfile.m3u) into the Pulse Code Modulation (PCM) audio format used by Bluetooth headsets; this is a limitation of Windows 98.
Other versions of Windows (2000, ME and XP) can translate m3u audio files into the PCM format.
Possible solutions are:
Upgrade to a newer version of Windows
Use an m3u-to-mp3 conversion utility to convert the file(s) into a format that is supported by Windows 98.
(Conversion utilities are available as freeware or shareware on the Internet.)
81
82
PC2PC Bluetooth
NOTES
User’s Guide
4. Technical Support
Refer to the following sources for additional information and for product and software updates.
The MSI website (http://www.msi.com.tw/) provides updated information on MSI Bluetooth hardware and software.
For technical support, please email to [email protected].
tw.
83
84
PC2PC Bluetooth
NOTES
User’s Guide
5. Glossary
BDA
Bluetooth Device Address. Every Bluetooth device has a unique
48-bit binary Bluetooth Device Address (BDA) burned into its
Read-Only Memory (ROM). This address cannot be changed by the end-user.
A device’s BDA is usually displayed in hexadecimal format;
00:D0:B7:03:2E:9F is a valid BDA.
Each Bluetooth device also has an operator-configurable, userfriendly name to help distinguish it from other Bluetooth devices. The user-friendly name may be up to 99 alphanumeric characters in length and may contain spaces. My Personal
Computer is a valid user-friendly name.
Device Inquiry
The process of searching for other Bluetooth devices.
DHCP
Dynamic Host Control Protocol-when enabled, connecting devices are assigned an Internet Protocol (IP) address by the server.
FTP
File Transfer Protocol
HCI
Host Controller Interface
85
PC2PC Bluetooth
IrDA
Infrared Data Association
IrMC
Infrared Mobile Communications
Link Key
An internally-generated unique security key that is exchanged by paired devices as proof of identity before a connection is established.
LMP
Link Manager Protocol—used by Bluetooth for internal communications.
Page Scan Mode
A Bluetooth mode in which a server is actively listening
(scanning) for a client to “page” it. The server then answers the page and attempts to set up a connection with the paging device (the client).
P a s s k e y
An alphanumeric string up to 16 characters in length. Passkeys are also called PIN codes, or Personal Identification Numbers.
Piconet
A network of devices connected in an ad hoc fashion using
Bluetooth technology. A piconet is formed when at least two
86
User’s Guide devices, such as a portable PC and a cellular phone, connect. A piconet can support up to eight devices. When a piconet is formed, one device acts as the master while the others act as slaves for the duration of the piconet connection.
PIM
Personal Information Manager—an application, such as
Microsoft Outlook, that is used to manage contacts, keep track of phone numbers, etc.
PIN
Personal Identification Number, also referred to as a “passkey” or “password.”
Scatternet
A group of independent and non-synchronized piconets that share at least one common Bluetooth device. Bluetooth devices must have point-to-multipoint capability to engage in scatternet communication. There may be a maximum of 10 fully loaded piconets in a scatternet.
Service Discovery
The process of determining the services that a Bluetooth server provides.
SysTray
The Windows system tray-usually located in the lower-right corner of the screen.
87
Advertisement
