BAND-IT T300 69 center punch tool Instruction manual

Instruction

Manual

Introduction:

T30069

CP Hand Tool

The T30069 Center Punch Tool installs BAND-IT 3/8" and 5/8", 201 Stainless

Steel and Galvanized Carbon Steel clamps.

Table of Contents:

1. Introduction & Safety Practices

2. Operating Instructions

3. Tool Assembly

4. Repair Parts List

5. 3/8" Adapter & Warranty

Safety Practices:

1. Read this manual and become familiar with the tool before use.

2. Protective eyewear should be worn during use.

3. Wear appropriate gloves for handling steel.

4. When applying clamps, care should be taken to insure fingers are not in contact with the clamp during installation.

5. Never attempt to clamp objects which have the potential to burst, shatter or otherwise cause bodily harm.

6. Do not use tool on live electrical sources.

BAND-IT-IDEX, Inc.

A Unit of IDEX Corporation

4799 Dahlia Street

Denver, CO 80216-0307 USA

P: 1-800-525-0758

F: 1-800-624-3925

WWW.CABLEJOINTS.CO.UK

THORNE & DERRICK UK

WWW.THORNEANDDERRICK.CO.UK

Page 1 of 5

Document # P15087 rev. G

© Copyright

BAND-IT-IDEX, Inc. 2010

All rights reserved

Operating

Instructions

1

FORWARD POSITION

OR “OPEN”

LOAD CLAMP

Push tension handle all the way forward. Insert

BAND-IT Center Punch clamp tail and push all the way into tool.

Tool Tip: To apply 3/8” wide clamps, use S03289 adapter kit. See attache d instructions for 3/8” adapter.

3

2

SLIDE

T30069

CP Hand Tool

TIGHTEN CLAMP

Tighten the clamp with short downward strokes. Tension handle should be in down position at completion of tightening clamp.

Note: Do not lift tension handle too high as it may open up buckle pusher, resulting in improper clamp application.

If clamp tension needs to be released before locking, move handle forward and move slide back against spring. This raises pulling dog and releases clamp tension.

4

LOCK CLAMP

Holding tension handle down, lock clamp by hitting punch at least twice with 2 lb. Mallet.

Note: Only use genuine BAND-IT Center Punch clamps. Disregarding this may result in substandard clamps or tool failure. BAND-IT CP clamps are made out of Type 201 Stainless Steel or Galvanized Carbon

Steel material with a stainless steel buckle for added strength.

REMOVE CLAMP TAIL

Hold work-piece and pivot the tool back and forth to break off clamp tail. Remove tail from tool by operating tension handle. When tail has moved through holding dog, raise tension handle and pull tail free.

BAND-IT-IDEX, Inc.

A Unit of IDEX Corporation

4799 Dahlia Street

Denver, CO 80216-0307 USA

P: 1-800-525-0758

F: 1-800-624-3925 www.BAND-IT-IDEX.com

Page 2 of 5

Document # P15087 rev. G

© Copyright

BAND-IT-IDEX, Inc. 2010

All rights reserved

Tool Assembly

T30069

CP Hand Tool

20

15 (2X)

18

11

21

17

16

19

12

1

10

9 (6X)

13

3

2

6

22 8

7 (2X)

4

OPTIONAL

5

14

INSTRUCTIONS:

DISSASSEMBLY AND ASSEMBLY OF PUNCH

To replace the punch (10), remove the head spring pin (3). Rotate the punch holder (11) until the retaining ball (12) is visible on the inside of the head (19). Remove the retaining ball and pull the punch out. Replace the punch and reassemble in reversed manner.

BAND-IT-IDEX, Inc.

A Unit of IDEX Corporation

4799 Dahlia Street

Denver, CO 80216-0307 USA

P: 1-800-525-0758

F: 1-800-624-3925 www.BAND-IT-IDEX.com

Page 3 of 5

Document # P15087 rev. G

© Copyright

BAND-IT-IDEX, Inc. 2010

All rights reserved

Repair Parts List

T30069

CP Hand Tool

REPAIR PARTS LIST FOR T300

NO.

1

2

3

4

PART

NUMBER

DESCRIPTION

A04987

COMPRESSION SPRING, 5/8” DIA.

C09787 SPRING PIN, 1/8” DIA.

J64287 HEAD SPRING PIN

S03289

ADAPTER INSERT TO INSTALL 3/8” WIDE CENTER PUNCH CLAMPS

(OPTIONAL)

S05777 BUCKLE PUSHER 5

6

7

S05887 HOLDING DOG

S06887 PIN, PULLING/HOLDING DOG

8

9

S06987 PIN, HEAD PIVOT

S08387 RETAINING RING, 5/16” DIA.

10 S19087 PUNCH

11 T25287 PUNCH HOLDER

12 T25587 RETAINING BALL, 5/32” DIA.

13 T25987 DECAL, DANGER

14 T26487 SPRING, HOLDING DOG

15 T26787 DOWEL PIN, 5/16” DIA.

16 T27040 SLIDE

17 T27187 PULLING DOG

18 T27288 LINK

19 T27488 HEAD

20 T27988 TENSION HANDLE ASSEMBLY

21 T28687 SLIDE BAR AND TENSION HANDLE ASSEMBLY

22 T28740 NOSE

-

-

-

-

T28088

T28888

T32190

T32290

HEAD ASSEMBLY

INCLUDES: HEAD SPRING PIN, DANGER DECAL, HEAD, PUNCH,

RETAINING BALL, AND PUNCH HOLDER

NOSE AND SLIDE ASSEMBLY

INCLUDES: NOSE, SLIDE, COMPRESSION SPRING, HEAD SPRING PIN,

AND SLIDE BAR AND TENSION HANDLE

PUNCH KIT

INCLUDES: PUNCH, PUNCH HOLDER AND RETAINING BALL

GRIPPER KIT

INCLUDES: PULLING DOG, COMPRESSION SPRING X 2, RETAINING RING X 3 AND

HOLDING DOG

BAND-IT-IDEX, Inc.

A Unit of IDEX Corporation

4799 Dahlia Street

Denver, CO 80216-0307 USA

P: 1-800-525-0758

F: 1-800-624-3925 www.BAND-IT-IDEX.com

Page 4 of 5

Document # P15087 rev. G

© Copyright

BAND-IT-IDEX, Inc. 2010

All rights reserved

3/8" Adapter &

Warranty

T30069

CP Hand Tool

1. To convert T300 center punch tool, rotate head back to expose buckle pusher and nose of tool.

2. Press down on the lobe at the rear of the buckle pusher to raise the front portion for insertion of adapter between the buckle pusher and the nose.

3. Seat the adapter against the buckle pusher with the post of the adapter hooked at the rear of the triangle shapes of the buckle pusher. Release the pressure on the buckle pusher lobe to secure the adapter into place. Rotate the head forward. The tool is now ready to use.

4. Repeat instructions 1 and 2 to remove adapter.

Warranty:

ADAPTER

PRESS DOWN & BACK

For Warranty information, visit the following URL

www.BAND-IT-IDEX.com/Warranty.html

BAND-IT-IDEX, Inc.

A Unit of IDEX Corporation

4799 Dahlia Street

Denver, CO 80216-0307 USA

P: 1-800-525-0758

F: 1-800-624-3925

WWW.CABLEJOINTS.CO.UK

THORNE & DERRICK UK www.BAND-IT-IDEX.com

TEL 0044 117 977 4647 FAX 0044 977 5582

WWW.THORNEANDDERRICK.CO.UK

Page 5 of 5

Document # P15087 rev. G

© Copyright

BAND-IT-IDEX, Inc. 2010

All rights reserved