Cornelius | SID851A/250S-BC | Operator`s manual | Cornelius SID851A/250S-BC Operator`s manual

SPIRAL ICEMAKERâ
DISPENSER
Operator’s Manual
MODELS: SID851A/250S
SID851A/250S-B
SID851W/250S
SID851W/250S-B
SID851A/250S-BC
SID851W/250S-BC
208--230/115V, 60HZ, 1PH
Part No. 90914
August, 1995
Revision D
THIS DOCUMENT CONTAINS IMPORTANT INFORMATION
This Manual must be read and understood before installing or operating this equipment
â REMCOR INC: 1995
PRINTED IN U.S.A
TABLE OF CONTENTS
Page
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
UNPACKING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BEVERAGE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
START -UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
7
7
7
10
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
REGULAR BASIS (OR AS REQUIRED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EVERY THREE MONTHS (OR AS REQUIRED) . . . . . . . . . . . . . . . . . . . . . . . . . . .
PERIODICALLY (OR AS REQUIRED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLEANING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ICE MAKER SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
14
14
14
14
DISPENSER SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FOR UNITS WITH BEVERAGE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
15
17
MAINTENANCE/ADJUSTMENT PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . .
THERMOSTAT ALTITUDE ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . .
BIN THERMOSTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLEARING EVAPORATOR FREEZE-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
30
30
30
ICE THICKNESS ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLEANING/REPLACE THE FILTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLEANING THE CONDENSER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HARVEST TIME ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MANUAL FILLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
31
31
32
32
34
LIST OF FIGURES
FIGURE 1. ELECTRICAL WIRING INSTALLATION INSTRUCTIONS . . . . . . . . .
FIGURE 2. INSTALLATION DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 3. MOUNTING TEMPLATE MODEL SID 851/250-B . . . . . . . . . . . . . . . .
FIGURE 4. MOUNTING TEMPLATE MODEL SID 851/250-BC . . . . . . . . . . . . . . .
FIGURE 5. BEVERAGE SYSTEM SCHEMATIC B MODELS . . . . . . . . . . . . . . . .
FIGURE 6. BEVERAGE SYSTEM SCHEMATIC -BC MODELS . . . . . . . . . . . . . .
3
4
5
6
8
9
FIGURE 7. WIRING SCHEMATIC SID 850/250 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 8. WIRING DIAGRAM SID 850/250 (208--230/115V, 1PH, 60HZ) . . . . .
FIGURE 9. REFRIGERATION SCHEMATIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 10. HARVEST TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
12
13
33
i
90914
TABLE OF CONTENTS (cont’d)
LIST OF TABLES
Page
TABLE 1. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
TABLE 2. LBS./24-HOUR ICE PRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TABLE 3. HARVEST CYCLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
90914
ii
GENERAL INFORMATION
DESCRIPTION
The Remcor S.I.D. (Spiral Ice Maker/Dispenser) is a unique, self-contained, counter top style unit that automatically makes hard, clear cube-quality ice and stores it in a sealed hopper for sanitary dispensing. The ice is
made by a new, patented process on a spiral-shaped, stainless steel evaporator and produces true cube quality
ice on the outside of the tubes. There are no augers; no compressing of flaked ice; no bearings; and no high
gear motor loads in the ice-making process. The unit has been designed to be simple, yet effective, to provide
many years of trouble-free operation.
Table 1. SPECIFICATIONS
Compressor:
Refrigerant:
Voltage:
AMPS:
Circuit Ampacity:
Fuse Size:
Ice Storage Capacity:
Ice Making Capacity:
Shipping Weight:
1 Horsepower
R-502/2.25 lbs. (Air Cooled); 2.75 lbs. (Water Cooled)
208-230/115, 1 phase, 60 Hertz
18
25
20A Time-Delay
225 lbs.
Up to 964 lbs./24 Hours
550 lbs.
Table 2. LBS./24-HOUR ICE PRODUCTION
Air Temp.
60°
70°
80°
90°
Water Temperature
40°
964
916
817
725
50°
901
858
756
680
60°
861
820
731
650
1
70°
806
777
700
630
80°
755
728
656
590
90°
712
687
619
556
90914
INSTALLATION INSTRUCTIONS
UNPACKING INSTRUCTIONS
1. With the unit upright, carefully remove the shipping crate. Inspect for shipping damage and report any such
damage to the shipper immediately.
2. Open the hinged service door and remove shipping tape from the ice drop cover, storage hopper cover and
agitator in the storage hopper.
3. Remove shipping tape from air inlet filter and sink grill.
INSTALLATION
NOTE:
An Everpure Model 9320-42 Systems IV, Model B1000 (or equal) ice maker quality water
treatment unit MUST BE INSTALLED in the water supply line to the ice maker. Failure to do so
may result in poor quality ice, low production output, and may cause premature failure of the
ice maker evaporator and void the extended evaporator warranty.
This ice maker is provided with a stainless steel evaporator designed to last the life of the product. But, some of
the chemicals in treated and untreated water, specifically chlorine and sulphur (sulphide), have the ability to attach stainless steel and cause premature failure. An initial investment in proper water treatment will pay for itself
in increased production, quality and long life of the product.
1. Location
Locate the ice maker/dispenser indoors in a well-ventilated area. Avoid exposure to direct sunlight and/or
heat caused by radiation.
Ambient room temperature must be in the range of 60° to 90° F. Do not install unit in an enclosed area
where heat build up could be a problem. For proper air flow for the refrigeration system, allow a 6?clearance at the back of the unit and a 12?clearance at the right side panel.
Consult Figure 1 for utility connection location.
Consult Figure 2 for dimensions for mounting unit to the counter with the hardware provide. Note that the
unit must be level for proper operation.
The unit must be sealed to the counter. The mounting template drawing (Figure 2) indicated the openings
which must be cut in the counter. Locate the desired position for the unit, then mark the outline dimensions
and cut-out locations using the template drawing. Cut openings in counter.
Apply a continuous bead of NSF International (NSF) listed silastic sealant (Dow 732 or equal) approximately 1/4?inside of the unit outline dimensions and around all openings. Then position the unit on the counter
within the outline dimensions. All excess sealant must be wiped away.
2. Plumbing
Connect the ice maker to a cold, potable water source suitable for drinking. Do not install unit on a water
softener line. It is recommended that a hand shut-off valve, strainer, and backflow preventer be used on the
incoming supply line. For Models: SID851/250S and SID851/250S-B, a 3/8?outside diameter compression
tube fitting is provided at the back of the unit for the water supply hook up (See Figure 1). For model
SID851/250S-BC, a 3/8?beverage tubing with a 3/8 x 1/4 barb splicer fitting is provided for connection
through the bottom opening in the unit to the water supply (See Figure 2).
90914
2
IMPORTANT: To ensure proper ice maker operation and also to reduce the frequency of water-related
service problems, a water filter should be installed. Remcor recommends the use of one of the
following basic systems:
1. Everpure, Inc.
660 No. Blackhawk Drive
Westmont, IL 60559
(708) 654-4000
Insurlce Twin System #9320-42
2. System IV
16632 Burke Lane
Huntington Beach, CA 92647
(714) 842-4221
Basic Water System #B1000
For specific recommendations on these filter systems for your local conditions, consult with a distributor in your
area or contact the filter manufacturer.
Models SID851/250S & SID851/250S-B
Connect two (2) 3/4?IPS (or equal) drain lines to the 3/4?threaded drain connections at the lower rear of the
unit. These lines must pitch downward to an open drain and must contain no traps or improper drainage will
result.
Model SID851/250S-BC
A 1?OD tubing drain elbow is provided at the bottom of the unit for the sink drain. Connect this elbow to a 7/8?
ID plastic drain tube.
A 3/4?IPS threaded drain connection for the ice maker is also provided at the bottom of the unit. Connect this
to a 3/4?IPS drain line (or equal).
These lines must pitch downward to an open drain and must contain no traps or improper drainage will result.
NOTE: In areas where consistently warm water temperatures are encountered, the use of a Remcor PreCooler in the water line is recommended to maximize the ice production of this unit. Contact Remcor
for more information on this product.
2. Electrical
A 4 x 2 junction box is located at the rear of the unit for the supply hook-up. Connect the ice maker to its
own circuit per the national electric code and local code. See SPECIFICATIONS for ampacity and fuse
size.
IMPORTANT: The wire size must be adequate for the ampacity rating, and the supply voltage must be
within a range of ± 10% for proper ice maker operation.
NOTE: The units require a 3 wire system plus earth ground for proper operations.
115/208-230V
1 PHASE
60 HERTZ
BLACK (HOT)
RED (HOT)
WHITE (NEUTRAL)
SUPPLY CONDUIT
GREEN (GROUND)
FIGURE 1. ELECTRICAL WIRING INSTALLATION INSTRUCTIONS
3
90914
4
90914
60
45 7/8
24
20 1/2
8 15/16
14
*FOR MODELS:
SID 851/250
SID 851/250-B
16 1/4
45 1/8
13 1/4
2 1/4
29
1
2 1/2
2 1/2
1 1/2
18 3/4
25 3/8
15 1/8
14 1/2
36
33 1/16
9 3/4
8 1/16
32 1/8
CLEARANCE NECESSARY ONLY
IF UNITS ARE INSTALLED IN AN
ENCLOSED SPACE.
DOOR WITH LOCK FOR ACCESS
TO ICE STORAGE AREA.
FIGURE 2. INSTALLATION DIMENSIONS
6
12
*ICEMAKER WATER IN
3/8 O.D. TUBE COMP. FITTING
*3/4-FPT DRAIN (2)
ACCESS PANEL FOR SERVICE
ELECTRICAL INPUT
ACCESS PANEL FOR SERVICE
AND BEVERAGE HOOK-UP
ACCESS PANEL FOR SERVICE
CONDENSER WATER IN
3/8-NPT (WATER COOLED ONLY)
CONDENSER WATER OUT
3/8-NPT (WATER COOLED ONLY)
AIR DISCHARGE GRILL
3 1/2
12 13/16
12
22 1/16
16
12
FOR BC MODELS:
ACCESS PANEL FOR BEVERAGE
AND UTILITY HOOK-UP
9 1/2
32
15 7/8-IN.
14-IN.
2 3/4-IN.
3/8 DIA.
10 1/2-IN.
32 1/2-IN.
36-IN.
16-IN.
2 1/8-IN.
UNIT OUTLINE FRONT
27 11/16-IN.
32-IN.
NOTE:
Shaded area indicates opening in
bottom for beverage tubing.
FIGURE 3. MOUNTING TEMPLATE MODEL SID 851/250-B
5
90914
32-IN.
27 11/16-IN.
3 1/16-IN.
1/2 DIA.
10 1/2-IN.
14 1/8-IN.
36-IN.
19 5/8-IN.
16-IN.
5 7/8-IN.
11 1/4-IN.
FRONT
UNIT OUTLINE
NOTE:
90914
Shaded area indicates opening in
bottom for beverage tubing and utilities.
FIGURE 4. MOUNTING TEMPLATE MODEL SID 851/250-BC
6
BEVERAGE SYSTEM
“B”models contain beverage faucets only and must be supplied with cold product from any remote cold plate or
refrigerated soda factory. “BC”units have a built-in cold plate, in addition to the beverage faucets and are designed to be supplied directly from syrup tanks and carbonator with no additional cooling required.
Installation
1. Locate the required openings in the counter top for the beverage lines as shown in Figure 3 (for “B”models) or Figure 4 (for “BC”models).
2. For “B”models, carefully pull the beverage tubers through the bottom opening in the unit and through the
clearance opening in the counter.
3. For “BC”models, 1/4?and 3/8?beverage tubing “pigtails”are provided at the front of the unit on the cold
plate for syrup and water line hook-up respectively.
To access these inlet tubes, remove the lower front panel above the sink. Remove the sink by disconnecting the sink drain connection; lifting the two (2) sink side mounting pins and pulling the sink forward.
4. Connect the beverage system product lines as indicated in Figure 5 (“B”units) and Figure 6 (“BC”units).
This work should be done by a qualified service person. Note that the hoses are marked with numbers
(1through 8) for syrup connection and “CW”for carbonated water connection.
5. For “BC”models, reverse the procedure in step 3 to reconnect the sink. Make sure that all drain connections are properly positioned before installing the lower front panel.
START-UP
1. Open the hinged service door. Remove ice drop cover and storage hopper cover.
2. Turn on water to ice maker.
3. Depress the flush switch to verify that the water dump valve operates and that the water drain lines are
open and not plugged.
WARNING: To prevent possible injury, do not stick fingers or hand into ice maker nozzle or
hopper with power applied to unit.
4. Put the “Stop/Run”switch in the “run”position. Observe that the ice maker goes through proper ice making
and harvest cycles. If unit malfunctions, consult the Troubleshooting Guide.
NOTE: Due to meltage loss because of a warm storage hopper, it will take longer to fill the hopper the
first time than when the ice maker has been operating continuously.
5. Depress the vend switch lever. Check that both the gate solenoid and agitator motor are energized simultaneously to lift the gate slide and rotate the agitator in the storage hopper, respectively. If either component
malfunctions, consult the Troubleshooting Guide. Replace the ice drop and hopper covers.
6. For beverage units, start up the beverage system and adjust the faucets to the proper brix. Contact your
local syrup distributor for complete information on the beverage system. For units with a built in cold plate,
it will take approximately one (1) hour from the initial machine start-up for the cold plate to be at full capacity.
7. The bin thermostat is calibrated at an atmospheric pressure equivalent at 500 feet above sea level. For
locations at higher elevations, it may be necessary to re-adjust these controls. Consult the Maintenance/
Adjustment Procedures section.
7
90914
90914
8
ITEMS OUTSIDE OF
BROKEN LINE ARE NOT
INCLUDED WITH UNIT
8
7
6
LINE LEGEND
CO2
CARB WATER
PLAIN WATER
SYRUP
OPTIONAL
1
2
3
4
4
3
FILTER
2
NON-CARB OR
CARB WATER
1
PRIMARY REGULATORS
FIGURE 5. BEVERAGE SYSTEM SCHEMATIC B MODELS
5
60-100 PSIG
5
6
OPTIONAL FOR
DIET OR
ROOT BEER
CARBONATOR
7
8
COLD PLATE
CO2 TANK
WATER
SUPPLY
15-50 PSIG
OPTIONAL
PRESSURE
REGULATOR
9
90914
LINE LEGEND
CO2
CARB WATER
PLAIN WATER
SYRUP
OPTIONAL
8
7
6
5
4
3
2
1
2
3
4
8
1,5,6,
7,8
7
NON-CARB OR
CARB WATER
6
5
60-100 PSIG
4
OPTIONAL FOR
DIET OR
ROOT BEER
CARBONATOR
FIGURE 6. BEVERAGE SYSTEM SCHEMATIC -BC MODELS
ITEMS OUTSIDE OF BROKEN LINE
ARE NOT INCLUDED WITH UNIT.
COLD PLATE
3
2
1
PRIMARY REGULATORS
FILTER
CO2 TANK
WATER
SUPPLY
15-50 PSIG
OPTIONAL
PRESSURE
REGULATOR
OPERATING INSTRUCTIONS
A temperature sensing control bulb located in the storage hopper starts and stops the ice making process in
response to ice level in the hopper. With this ice level control “calling”for ice (hopper ice level is low), ice begins
to form on the stainless steel tubing coils in the evaporator coils until it contacts the ice thickness probe (low
voltage conductivity sensor). At this point, the conductivity probe triggers the harvest timer motor. The harvest
timer contains five (5) cam operated switches which function as detailed in the table on the following pages.
Table 3. HARVEST CYCLE
Time
0--86 Seconds
Cam Switch
#1
Action
Timer motor energized
1--23 Seconds ± 1 Second
#4
Water dump valve open
1--37 Seconds ± 2 Seconds
#2
Hot gas solenoid valve open.
Air pump off.
Condenser fan motor off.
37--90 Seconds
#2
Air pump on.
Condenser fan motor on.
Hot gas solenoid valve closed.
36--39 Seconds
#3
Harvest motor on.
43--47 Seconds
#5
Hopper agitator motor operates.
When ice contacts the ice lever control bulb in the storage hopper, the control will shut down the refrigeration
system. If this signal occurs during the harvest cycle, the harvest cycle will be completed before shutdown occurs.
To dispense ice, push the lever located on the lower front panel. Ice will flow from the ice chute until the lever is
released.
For units with a built-in cold plate, ice will automatically fill the cold plate cabinet. Allow one (1) hour for the cold
plate to reach its maximum capacity. Start up the beverage system and adjust the faucets to the proper brix.
Pushing the lever on any faucet will provide beverage of the appropriate flow.
90914
10
208-230 / 115V, 1PH,
(4 WIRE SYSTEM)
L1
TP
N
COMPRESSOR
C
CC
L2
5
R
5
RUN CAP
CC
2
START
RELAY
START CAP
STOP /
RUN
LPS
HPS
BIN T’STAT
1
CC
2
COMPRESSOR
CONTRACTOR
HARVEST MOTOR
NC
RED
HT3
C
BLUE
NO
CAP
CONDENSER FAN
NC
HT2
C
RUN
NO
AIR PUMP
CLEAN
HG SOL VALVE
NC
HT4
C
WATER DUMP VALVE
NO
FLUSH
NO
WATER LEVEL
PROBE
C
L
N
WATER FILL VALVE
NC
FILL
ICE THICKNESS
PROBE
NO
HI
C
LO
COM
NC
NC
HT1
CONDUCTIVITY
CONTROL
HT
C
NO
NO
HT5
VEND SWITCH
NC
AR
C
F
HARVEST
TIMER
AGITATOR
RELAY
GATE SOLENOID
AGITATOR MOTOR
AR
MOTOR HEATER
R
BEVERAGE TRANSFORMER (OPTIONAL)
24 V TO BEVERAGE FAUCETS
FIGURE 7. WIRING SCHEMATIC SID 850/250
11
90914
BLUE
WHT
HQ SOL VALVE
YEL
YEL
BLUE
BRN
P
I
N
K
BLK
PUR
NEUTRAL
YEL
LPS
R
E
D
HARVEST
TIME
O
R
N
FUSE 1-1/4 AMP
TIME DELAY
BLUE
WHT
WHT
WHT
WATER FILL VALVE
BLK
ORN
RED
R
E
D
BRN
WHT
YEL
ICE THICKNESS PROBE
BLK
BLK
BLK
WHT
RED
BLUE
RED
RED
AGITATOR
MOTOR CAP
PINK
RED
WHT
BLUE
WATER LEVEL PROBE
HARVEST
MOTOR CAP.
W TERMINAL BOARD
H MORE LOCATION MAY VARY
T
WHT
HARVEST MOTOR
BLK
ORN
BLK
RED
CLEAN
ICE MAKER
RUN
PINK
BRN
Y
E
L
RUN
S
BRN
START
RELAY
C
R
COMPRESSOR MOTOR
L2
L1
FILL WATER
VALVE INDICATOR
RED
1
BLK
STOP
GRN
CONDUCTIVITY
CONTROL
BRN
PUSH TO
FLUSH
RED
3
BLK
WHT
CONDENSER FAN MOTOR
HI LO COM
BLK
PUR
BLK
Y R
E E
L D
O
R
N
BLK
BLK
MERCURY
RELAY
PINK
MANUAL
WATER
FILL
2
BLK
AIR PUMP
Y
E
L
BRN
BLK
208--230V/115V 1PH, 60HZ, 20AMP
FIELD SUPPLIED
GRN
PINK
COMPRESSOR CONTACTOR
ORN
BIN
T’STAT
BRN
W
H
T
RED
COMPRESSOR
START CAP.
BLK
O
R
N
L1
GRN
W
H
T
MOTOR
HEATER
B
L
K
RED
RED
RED
NO
REAR JUNCTION
BOX POWER IN
BLK
BLUE
ORANGE
L2
BLK
WHT
B
L
U
E
BLK
HPS
RED
BLK
WHT
B
R
N
Y
E
L
R
W
E B H
D L T
K
COMP.
RUN
CAP.
Y
E
L
YEL
RED
GATE
SOLENOID
GRN
B
L
K
WHT
BLK
WHT
VOID
SWITCH
TERMINAL
BOARD
Y
E
L
B
L
K
BRN
W
H
T
AGITATOR
MOTOR
115 VOLT
NEUTRAL
W
H
T
BLK
Y
E
L
WHT
Y
E
L
WHT
YEL
BEVERAGE
TRANSFORMER
(OPTIONAL)
WHT
BRN
90914
WATER DUMP VALVE
FIGURE 8. WIRING DIAGRAM SID 850/250 (208--230/115V, 1 PH, 60HZ)
12
FIGURE 9. REFRIGERATION SCHEMATIC
13
90914
MAINTENANCE
REGULAR BASIS (or as required)
Cleaning of the ice maker is recommended on a regular basis not only for sanitary reasons, but also to maintain
the performance of the unit. Build-up of lime and scale can hinder ice making production rates and interfere with
proper dispensing of the ice. See Cleaning Instructions for the recommended procedure.
EVERY THREE MONTHS (or as required)
It is recommended that the air inlet filter be cleaned every three (3) months or sooner depending on the operating environment for proper refrigeration system performance. On an air-cooled unit, also check that the condenser is free of dirt/foreign material that could cause air flow blockage. Consult the Maintenance/Adjustment
Procedures section for cleaning these items.
PERIODICALLY (or as required)
Check the vending area sink for proper water drainage. Remove any foreign material from the sink to prevent
drain blockage.
CLEANING INSTRUCTIONS
IMPORTANT: The ice maker should be cleaned at a minimum of three (3) month intervals or more
frequently, depending on local water conditions. The storage hopper interior should be cleaned once a
month.
CAUTION: Do not use metal scrapers, sharp objects or abrasives on the surface of the
storage hopper, as damage may result. Do not use solvents or other cleaning agents, as
they may attack the plastic surface. Use only the recommended chemicals and solutions for
both the ice maker and hopper.
Ice Maker Section
1. Open the hinged service door.
2. Put the “Stop/Run”switch in the “stop”position at the end of the harvest cycle.
WARNING: The unit is still plugged into the electrical power during ice maker section
cleaning. Therefore, do not reach into hopper, and do not contact exposed electrical wiring
or components.
3. Remove the ice drop cover from the evaporator and the storage hopper cover.
4. Seal the evaporator outlet with the plastic plug provided with the unit and replace the ice drop cover.
5. Remove cleaning fill plug and add four (4) ounces of Virginia Ice Machine Cleaner to the evaporator and
replace cleaning fill plug.
CAUTION: Virginia Ice Machine Cleaner is a mild acid, therefore, normal care should be
taken when using. Keep out of eyes and cuts. Read warnings on package before using. Do
not operate unit in the cleaning mode without the ice drop cover in place. There may be
some overflow of cleaning solution through the evaporator vent tube during the cleaning cycle.
90914
14
6. Push manual water fill switch and fill evaporator with water (approximately 5 seconds).
7. Put the “Clean/Run”switch in the “clean”position. Allow unit to run in the cleaning mode for at least 30
minutes.
8. Put the “Clean/Run”switch in the “run”position.
9. Depress the “Flush”switch push button and drain evaporator for about 1-1/2 minutes. Release push button. Push manual water fill switch and allow evaporator to refill with water. Repeat Step 9 three (3) times to
thoroughly remove cleaning solution from evaporator.
10. Depress the “Flush”switch push button for 1-1/2 minutes to drain the evaporator.
11. Remove the evaporator plug.
12. Put the “Stop/Run”switch in the “run”position and allow unit to run through at least three (3) complete ice
making cycles or until ice is free of “sweet”taste.
WARNING: If unit fails to harvest ice, put the “Stop/Run” switch in the “stop” position.
Depress the “Flush” switch push button for 1-1/2 minutes to drain the evaporator. Flush
the evaporator with hot water to thoroughly melt all the ice in the evaporator. Repeat Step 9
to remove all traces of the cleaning solution from the evaporator.
13. Dispense all ice out of storage hopper and discard.
Dispenser Section
1. Turn off main electrical power supply to machine.
2. Remove agitator assembly from storage hopper and wash and rinse it thoroughly.
3. Wash down all inside surfaces of the ice storage area, including the top cover and ice drop cover with a
mild detergent solution and rinse thoroughly to remove all traces of detergent.
4. Replace agitator.
5. Remove ice chute cover as follows:
A.
Flex sides outward to disengage lower pins.
B.
Lift ice chute cover to disengage upper pins.
C.
Lower ice chute cover down out of unit. Note: It may be helpful to twist cover slightly.
6. Clean the inside of the ice chute and ice chute cover with a mild detergent solution. Rinse thoroughly to
remove all traces of detergent.
7. Reverse steps above to reassemble ice chute.
8. Sanitize the inside of the hopper agitator, ice chute, the hopper cover and ice drop cover with a solution of
1 ounce of household bleach to 2 gallons of water. (200 PPM)
9. Replace the hopper cover and ice drop cover. Turn on the electrical power supply. The ice maker is ready
for normal operation.
For Units With Beverage System
Cold Plate
1. Carefully remove the lower front panel. (Below beverage faucets).
15
90914
2. Slide the cold plate cover back. (Remove shipping tape and discard).
3. Remove any debris from the drain trough and spring. Check that drain hole is not clogged.
4. Wash down the inside of the cold plate with a mild detergent solution and rinse. A small, long handled
brush will be found helpful in reaching the corners.
5. Slide the cover forward, taking care that it is securely positioned on the cold plate.
6. Replace the lower front panel.
Beverage System
1. Remove the faucet spouts, wash in mild detergent, rinse and replace.
2. Disconnect electrical power to the carbonator. Shut off the water supply and close the CO2 regulator to the
carbonator.
3. Disconnect the syrup tanks from the system.
4. Energize the beverage faucets to purge the remaining soda water in the system.
5. Use a clean 5 gallon tank for each of the following:
Cleaning Tank:
Fill with hot (120° - 140° F) potable water.
Sanitizing Tank:
Fill with a chlorine sanitizing solution in the strength of 1 ounce of household bleach(sodium hypochlorite) to 2 gallons of cold (ambient) potable water (200 PPM).
6. Repeat the following procedure on each of the units’syrup product lines:
A.
Connect the cleaning tank to the syrup line to be sanitized and to the CO2 system.
B.
Energize the beverage faucet until the liquid dispensed is free of any syrup.
C.
Disconnect the cleaning tank and hook up the sanitizing tank to the syrup line and CO2 system.
D.
Energize the beverage faucet until the chlorine sanitizing solution is dispensed through the faucet.
Flush at least 2 cups of liquid to ensure that the sanitizing solution has filled the entire length of the
syrup lines. Allow the sanitizer to remain in the line for twenty (20) minutes.
E.
Disconnect the sanitizing tank. Hook up the product tank to the syrup line and to the CO2 system.
F.
Energize the faucet to flush the sanitizing solution from the syrup line and faucet. Continue to draw on
the faucet until only syrup is dispensed.
7. Repeat Step 2 in reverse order to turn on the carbonator. Dispense at least 1 cup of beverage from each
faucet. Check taste. Continue to flush if needed, to obtain a satisfactory tasting drink.
90914
16
TROUBLESHOOTING GUIDE
The following pages contain troubleshooting charts designed to aid an experienced service person in diagnosing
any operating problem which may be experienced. It is assumed that normal service techniques and skills are
familiar to the person doing the troubleshooting. In order to gain maximum benefit from these charts please
note:
1. Start at the beginning of the chart and supply the appropriate answer to each question.
2. Do not skip any section, unless instructed to do so. You might miss the solution to your problem.
3. Evaluate the possible problem causes in the sequence in which they are presented. In general, they begin
with the most likely (or easiest) to check and proceed to the less likely (or more complicated).
4. If after checking all indicated causes, the problem is not resolved, it is recommended that you
re-try a second time, carefully evaluating the symptoms and modifying your answers as necessary.
5. If you are unable to resolve a problem after several attempts, contact Remcor Customer Service
for assistance.
17
90914
START
DOES UNIT
OPERATE?
NO OPERATION OF ANY
COMPONENT.
NO
GO TO 1.
YES
IS
ICE MAKER
O.K.?
ICE MAKER ABNORMAL.
DISPENSER AND BEVERAGE
WORK NORMALLY.
NO
GO TO 2.
YES
IS
DISPENSER
O.K.?
DOES NOT DISPENSE.
ICE MAKER WORKS O.K.
NO
GO TO 3.
YES
IS
BEVERAGE
SYSTEM
O.K.?
PROBLEM WITH BEVERAGE
FAUCETS OR DRINK QUALITY.
NO
GO TO 4.
YES
DONE
90914
18
1. TOTALLY INOPERATIVE
YES
POWER
PRESENT AT
REAR JUNCTION
BOX?
YES
CHECK FOR LOOSE CONNECTION
OR BROKEN WIRE INSIDE UNIT.
NO
IS
SUPPLY FUSE
BLOWN (OR C/B
TRIPPED)?
NO
CHECK FOR LOOSE CONNECTION
OR BROKEN WIRE IN SUPPLY
WIRING OF UNIT.
IS LINE
VOLTAGE
WITHIN ± 10% OF
NAMEPLATE
VOLTAGE?
NO
YES
1.
2.
IS
FUSE OR C/B
SIZE PROPER?
YES
CHECK FOR SHORT CIRCUIT IN
WIRING INSIDE UNIT.
CHECK COMPONENTS FOR SHORT
CIRCUIT OR GROUNDED WIRING.
NO
IS
LINE VOLTAGE
HIGH OR
LOW?
REPLACE WITH CORRECT
SIZE DEVICE.
LOW
HIGH
IS
OTHER EQUIP.
ON SAME
CIRCUIT?
YES
INSTALL BUCKING TRANSFORMER
TO REDUCE LINE VOLTAGE.
NO
1.
2.
REMOVE ALL OTHER EQUIPMENT
FROM ICE MAKER CIRCUIT.
INSTALL NEW DEDICATED CIRCUIT
FOR ICE MAKER.
1.
2.
3.
19
CHECK FOR LOOSE OR CORRODED CONNECTION IN SUPPLY WIRING.
CHECK SUPPLY WIRING FOR UNDERSIZED WIRE, AND REPLACE.
INSTALL BOOSTING TRANSFORMER TO
RAISE LINE VOLTAGE.
90914
2. ICE MAKER PROBLEM
DOES
ICE MAKER
OPERATE?
NO
GO TO 2.A
YES
YES
IS ICE
PRODUCED?
NO
DOES
COMPRESSOR
RUN?
YES
IS
ICE ON
EVAPORATOR?
NO
NO
GO TO 2.B
GO TO 2.C
IS ICE
PRODUCTION
NORMAL?
YES
NO
GO TO 2.D
GO TO 2.E
YES
DONE
90914
YES
IS ICE
QUALITY
NORMAL?
20
NO
GO TO 2.F
2.A ICE MAKER PROBLEM
IS
HOPPER
FULL?
YES
RUN/STOP
SWITCH?
RUN
STOP
PUT SWITCH IN
RUN POSITION.
NO
NORMAL SHUTOFF ON
BIN THERMOSTAT.
YES
1.
2.
IS BIN
THERMOSTAT
OPEN?
NO
CHECK THERMOSTAT ADJUSTMENT.
REPLACE BIN THERMOSTAT.
IS
WATER
LEVEL NORMAL
IN EVAP.?
YES
IS LOWPRESSURE
SWITCH
OPEN?
YES
NO
NO
NO
IS HIGHPRESSURE
SWITCH
OPEN?
YES
CHECK FOR LOOSE CONNECTION
OR BROKEN WIRE.
1.
2.
3.
4.
5.
6.
AIR-COOLED UNITS
CHECK THAT WATER SUPPLY IS OPEN.
CHECK WATER SUPPLY FILTER.
CHECK FOR PLUGGED WATER SOLENOID
VALVE.
CHECK ADJUSTMENT OF TIMER CAM #4.
(WATER DUMP)
CHECK TIMER SWITCH #4.
CHECK IF WATER DUMP VALVE IS STUCK
OPEN.
1.
2.
3.
4.
5.
6.
CHECK FOR RESTRICTED AIR FLOW AT TOP
OR REAR OF UNIT.
CHECK FOR HOT AIR RECIRCULATING TO TOP
INLET. ELIMINATE BY BAFFLING.
CHECK FOR DIRTY INLET AIR FILTER.
CHECK FOR DIRTY AIR-COOLED CONDENSER.
CHECK CONDENSER FAN MOTOR.
CHECK FOR REFRIG. OVER-CHARGE.
WATER-COOLED UNITS
1.
2.
1.
2.
3.
4.
CHECK FOR REFRIGERANT UNDER-CHARGE
CHECK TXV VALVE.
21
CHECK WATER SUPPLY TO CONDENSER.
CHECK FOR FAULTY WATER REG. VALVE.
CHECK FOR REFRIG. OVER-CHARGE.
CHECK FOR FOULED CONDENSER.
90914
2.B COMPRESSOR INOPERATIVE
IS
LINE VOLTAGE
WITHIN ± 10%
OF NAMEPLATE
VOLTAGE?
YES
IS
THERMAL
PROTECTOR
OPEN?
NO
IS
CONTACTOR
PULLED
IN?
NO
YES
YES
CHECK VOLTAGE
PROBLEMS IN 1.
YES
NO
IS
COMPRESSOR
BODY
COLD?
1.
NO
2.
3.
4.
5.
CHECK FOR LOOSE OR BROKEN WIRING
CONNECTION IN COMPRESSOR POWER
CIRCUIT.
CHECK CONTACTOR.
CHECK STARTING RELAY.
CHECK CAPACITOR(S).
CHECK COMPRESSOR MOTOR.
REPLACE
THERMAL
PROTECTOR.
YES
IS
120V.
PRESENT AT
CONTACTOR
COIL
TERMINAL?
REPLACE CONTACTOR.
NO
1.
2.
90914
22
CHECK FOR LOOSE OR BROKEN
WIRING CONNECTION IN CONTROL
CIRCUIT.
GO TO 2.A.
2.C NO ICE ON EVAPORATOR
IS
HARVEST
TIMER
RUNNING?
NO
IS
EVAPORATOR
COLD?
YES
NO
YES
IS
HOT GAS SOLENOID
ENERGIZED?
YES
IS
WATER LEVEL
NORMAL?
NO
NO
YES
1.
CHECK WATER
PROBLEMS IN 2.A.
2.
CHECK
REFRIGERATION
SYSTEM.
YES
3.
IS
COND. CONTROL
ENERGIZED?
CHECK FOR REFRIGERANT
UNDER-CHARGE.
CHECK HOT GAS SOLENOID
FOR LEAKING SEAT.
GO TO 2.A.
NO
YES
CHECK TIMER
SWITCH #1.
1.
2.
1.
2.
IS
HARVEST TIMER
HOME?
CHECK FOR OPEN CONDUCT
PROBE WIRING.
CHECK CONDUCTIVITY
CONTROL.
1.
CHECK ADJUSTMENT OF
TIMER CAM #2. (HOT GAS)
CHECK TIMER SWITCH #2.
2.
3.
23
NO
CHECK ADJUSTMENT OF TIMER
CAM #1. (TIMER HOME)
CHECK TIMER SWITCH #1.
CHECK TIMER MOTOR.
90914
2.D FROZEN EVAPORATOR
1.
2.
SHUTOFF ICE MAKER AND THAW EVAPORATOR.
START ICE MAKER.
IS
AMBIENT ABOVE
60°F?
1.
NO
2.
ARRANGE TO MAINTAIN MINIMUM
60° F AMBIENT.
CONDUCT FACTORY REGARDING
SPECIAL APPLICATION.
YES
IS
VOLTAGE WITHIN
±10%?
NO
CHECK VOLTAGE ITEMS IN 1.
YES
DISCONNECT PROBE WIRE FROM
CONDUCTIVITY CONTROL.
DOES
TIMER
START?
NO
1.
2.
CHECK TIMER MOTOR.
CHECK CONDUCTIVITY CONTROL.
YES
1.
HOT
GAS OPERATION
O.K.?
NO
2.
3.
CHECK ADJUSTMENT OF TIMER
CAM #2. (HOT GAS)
CHECK TIMER SWITCH #2.
CHECK HOT GAS SOLENOID.
YES
1.
WATER
DUMP
O.K.?
NO
2.
3.
CHECK ADJUSTMENT OF TIMER
CAM #4. (WATER DUMP)
CHECK TIMER SWITCH #4.
CHECK DUMP SOLENOID.
YES
DOES
ICE HARVEST
NORMALLY?
NO
YES
90914
24
2.D (CONT’D)
YES
NO
1.
2.
3.
4.
CHECK ADJUSTMENT OF TIMER CAM
#3. (HARVEST MOTOR)
CHECK TIMER SWITCH #3.
CHECK HARVEST MOTOR CAPACITOR.
CHECK HARVEST MOTOR.
REPLACE PROBE WIRE ON
CONDUCTIVITY CONTROL
DURING HARVEST CYCLE.
DOES
TIMER RETURN
HOME?
1.
NO
2.
CHECK ADJUSTMENT OF TIMER
CAM #1. (TIMER HOME)
CHECK TIMER SWITCH #1.
YES
WAIT ONE FULL FREEZING
CYCLE (APPROX. 6-10 MIN.)
DOES
HARVEST
INITIATE?
1.
NO
2.
CHECK PROBE WIRING FOR
SHORTED CONNECTION.
CHECK CONDUCTIVITY CONTROL.
YES
DOES
ICE HARVEST
NORMALLY?
1.
NO
2.
REPEAT PREVIOUS CHECK OF OPERATION OF HARVEST
COMPONENTS IN 2.D.
ADJUST ICE THICKNESS PROBE ONLY AFTER ALL OTHER FACTORS HAVE BEEN CHECKED THOROUGHLY.
YES
DONE
25
90914
2.E LOW ICE PRODUCTION
IS
WATER LEVEL
NORMAL?
NO
CHECK WATER ITEMS IN 2.A.
YES
IS
WATER TEMP.
HIGH?
YES
NORMAL EFFECT. INSTALL
REMCOR PRE-COOLER TO
INCREASE CAPACITY.
YES
NORMAL EFFECT. ARRANGE
FOR LOWER AMBIENT AIR
TEMP. IF POSSIBLE.
NO
IS
AMBIENT TEMP.
HIGH?
NO
IS
ICE THIN?
YES
GO TO 2.C.
NO
CHECK REFRIGERATION
SYSTEM.
90914
26
2.F POOR ICE QUALITY
YES
IS
ICE CLOUDY?
NO
NO
IS
ICE SOFT?
DONE
YES
1.
2.
3.
4.
5.
6.
7.
CHECK AIR PUMP.
CHECK ADJUSTMENT OF TIMER CAM #4. (WATER
PUMP)
CHECK TIMER SWITCH #4.
CHECK WATER DUMP VALVE.
CHECK WATER FILTER.
INCREASE WATER DUMP BY ADJUSTING TIMER
CAM #4.
INSTALL ADDITIONAL WATER TREATMENT DEVICES FOR SPECIFIC PROBLEM WATER.
27
90914
3. DISPENSER PROBLEM
YES
DOES
AGITATOR
ROTATE?
YES
NO
DOES
GATE OPEN?
NO
1.
2.
3.
NO
CHECK MOTOR CAPACITOR.
CHECK TIMER SWITCH #5.
CHECK AGITATOR MOTOR.
1.
2.
1.
IS
HOPPER LEVEL
TOO HIGH?
NO
2.
3.
YES
1.
2.
4.
CHECK FOR BURNED OUT SOLENOID.
CHECK FOR STUCK OR BINDING GATE
MECHANISM.
CHECK FOR BLOWN SOLENOID FUSE IN ELECTRICAL BOX. IF FUSE IS BLOWN, CHECK FOR
STUCK GATE MECHANISM, BURNED OUT SOLENOID, OR LOW VOLTAGE.
CHECK VEND SWITCH.
CHECK FOR LOOSE OR BROKEN WIRE CONNECTION IN SOLENOID CIRCUIT.
CHECK VOLTAGE PROBLEMS IN 1.
CHECK BIN THERMOSTAT
ADJUSTMENT.
REPLACE BIN THERMOSTAT.
IS
ICE SLUSHY?
YES
1.
2.
3.
4.
5.
NO
DONE
90914
IS
VOLTAGE AT
SOLENOID
103-126V.?
28
CHECK HOPPER DRAINS.
CHECK LEVEL OF UNIT.
CHECK FOR WATER OVERFLOW FROM EVAPORATOR. SEE SECTION 2.
CHECK ADJUSTMENT OF TIMER CAM #5.
(AGITATION)
CHECK TIMER SWITCH #5.
YES
4. BEVERAGE SYSTEM PROBLEM
1.
IS
ONE OR MORE
FAUCETS
INOPERATIVE?
YES
2.
3.
4.
CHECK WIRING CONNECTIONS TO INOPERATIVE FAUCETS.
REPLACE INOPERATIVE FAUCETS.
CHECK WIRING CONNECTIONS FROM
24V. TRANSFORMER.
CHECK 24V. TRANSFORMER.
NO
IS
BEVERAGE
COLD?
1.
NO
2.
CHECK REMOTE COOLING
SYSTEM. (-B MODELS)
CHECK FOR ICE ON COLD
PLATE. (-BC MODELS)
YES
IS
BEVERAGE
PROPERLY
CARBONATED?
NO
3.
4.
CHECK CO2 PRESSURE.
CHECK CARBONATOR.
1.
2.
3.
4.
CHECK WATER SUPPLY PRESSURE.
CHECK SUPPLY FILTER.
CHECK CARBONATOR.
CHECK FAUCET BRIX.
YES
IS
BEVERAGE
TOO SWEET?
YES
NO
IS
BEVERAGE
TOO WATERY?
YES
1.
2.
3.
CHECK IF SYRUP TANK IS EMPTY.
CHECK CO2 PRESSURE.
CHECK FAUCET BRIX.
NO
DONE
29
90914
MAINTENANCE/ADJUSTMENT PROCEDURES
THERMOSTAT ALTITUDE ADJUSTMENTS
IMPORTANT: Adjust the bin thermostat setting only if storage hopper over fill is a problem.
BIN THERMOSTAT
1. Open the hinged service door.
2. The adjustment screw is located below the “Flush”switch on the left side of the electrical box.
3. For altitudes up to 6,000 feet, turn the adjustment screw COUNTERCLOCKWISE as follows:
ELEVATION (FEET)
2,000
4,000
6,000
COUNTERCLOCKWISE TURN
1/13
1/6
1/4
4. For altitudes above 6,000 feet, consult the factory.
CLEARING EVAPORATOR FREEZE-UP
WARNING: To prevent possible injury, do not place fingers or hand into ice maker nozzle or
hopper with power applied to the unit.
1. Open the hinged service door.
2. Place the “Stop/Run”switch in the “Stop”position.
3. Close the water supply valve to the ice maker.
4. Remove the ice drop and hopper covers.
5. Depress the “Flush”switch push button and drain the evaporator.
6. Pour hot water into the evaporator ice exit opening. It will be necessary to use either a funnel or a container
with a spout. Fill the evaporator completely.
7. Drain the evaporator. Repeat steps 5 and 6 as required to ensure that all the ice in the evaporator is
melted.
8. Open the water supply valve. Depress the fill switch and refill evaporator.
9. Replace the ice drop and hopper covers.
10. Consult TROUBLESHOOTING GUIDE to determine cause of freeze-up before putting unit back in service.
90914
30
ICE THICKNESS ADJUSTMENT
WARNING: Do not adjust ice thickness probe unless all other problem causes have been
evaluated.
1. Open the hinged service door and remove the ice drop and hopper covers.
2. Collect and weigh the ice produced during the harvest cycle. The amount of ice harvested should weigh
approximately five (5) pounds. Use the following procedure to adjust the probe to obtain this weight. (A
clockwise adjustment will reduce the harvest weight while counterclockwise turns will increase the amount).
CAUTION: Do not turn the screw on the end of the probe. Rotate the plastic probe body
only using a 3/8 inch open end wrench. Make adjustments in 1/8 inch turn increments.
A.
Place the “Stop/Run”switch in the “Stop”position. (If unit is in the ice-making cycle, stop the unit at
the end of the harvest cycle).
B.
Access to the probe is obtained by removing the rear service panel. (For units without beverage faucets, the probe can be adjusted from the front by removing the lower front panel if rear access is
blocked).
C.
Adjust the probe.
D.
Place the “Stop/Run”switch in the “Run”position.
E.
Collect and weigh the ice harvested. Repeat step A through E as necessary to obtain the required
amount of ice.
3. In making an initial adjustment (for example, if the probe has been removed and replaced for any reason),
turn probe clockwise until it just touches the evaporator coil (a slight back pressure will be felt). Turn probe
counterclockwise 2-1/2 turns. Follow procedure in step 2 to obtain the required ice harvest weight.
CLEANING/REPLACE THE FILTER
1. Remove the filter from the cabinet panel by sliding it forward toward the front of the unit.
2. Wash the filter in a solution of warm water and a mild detergent. Do not use caustic detergents as they
may attack the aluminum filter elements.
3. Dry filter thoroughly.
4. For maximum effectiveness, reactivate the filter with an air filter coating (see Parts List, Miscellaneous
Components).
CLEANING THE CONDENSER
Air-Cooled Units.
1. Disconnect power to the unit.
2. Remove the upper right side panel.
3. Remove all dirt/foreign material built up from the condenser fins (fan side). Be careful not to damage the
fins. It is recommended that a power vacuum cleaner with a “crevice”tool attachment be used.
31
90914
HARVEST TIME ADJUSTMENT
WARNING: Disconnect electrical power to the unit before servicing the timer in the
electrical box.
1. Disconnect power to ice maker.
2. Open the hinged service door and remove the electrical control box cover.
3. Place the “Stop/Run”switch in the “Stop”position.
4. Using Figure 10 as a guide, set the timer cam tabs as follows, starting with cam wheel No.1 (all cam tab
positions are in relation to No.1 left cam tab).
NOTE: Timer cam wheels can be manually rotated only in the normal direction of rotation-downward as
viewed from the front of the unit.
A.
“Manually”adjust the cam tabs by using each “click”as the cam tab is rotated, as equivalent to .75
seconds.
B.
Set up cam wheel No.1 with the left and right cam tabs back-to-back as shown in Figure 7A.
C.
Adjust the cam tabs on wheels No. 2 through No. 5 in sequence as shown on the chart. Rotate the
cam wheels manually downward to set each wheel.
D.
After the cam tabs are manually set, reconnect power to the ice maker.
E.
Rotate the cam wheels slightly to activate the timer motor (No. 1 telltale down).
F.
Using a stop watch, time the cam switch telltales. Adjust the cam tabs as necessary for the required
cycle times.
MANUAL FILLING
In the event that the ice maker is not functioning, the hopper may be manually filled with ice.
1. Open the hinged service door.
2. Place the “Stop/Run”switch in the “Stop”position.
WARNING: Electrical power is on to the agitator motor and the gate solenoid.
Avoid contact with these components.
3. Remove the ice drop and storage hopper covers.
4. Fill hopper with ice and replace covers. Unit is now ready for dispensing.
CAUTION: Do not use crushed or flaked ice. Use of bagged ice, which has frozen into large
chunks, can void warranty. The agitator is not designed to be an ice crusher. Use of large
chunks of ice which “jam up” inside the hopper will cause failure of the agitator motor and
damage the hopper. If bagged ice is used, it must be carefully and completely broken into small,
cube size pieces before filling into the storage hopper. Do not allow foreign material to enter the
ice storage hopper.
90914
32
10A
FIGURE 10. HARVEST TIMER
33
90914
PARTS LIST
PART NUMBERS
DESCRIPTION
Dispenser Components
Gate Slide
Depressor Lever
Depressor Retainer
Agitator
Vend Switch
Switch Boot
Agitator Motor with Gasket
Agitator Motor Shaft Seal
Agitator Motor Plate Insulation
Sink
Sink Grill
Ice Chute, Back Section
Ice Chute Cover
Gate Gasket
Gate Solenoid Assembly
Gate Rebuilding Kit
Agitator Motor Heater
Agitator Motor Gasket
DESCRIPTION
Electrical Controls
250
Air Cooled
250 “BC”
21491
22777
22644
23692
30895
31007
31197-1
50891
50967
51024
70496
53015
53016
50770
31470
70438
---------50481
21491
22777
22644
23692
30895
31007
31197-1
50891
50967
52208
70496
53015
53016
50770
31470
70438
30794
50481
Water Cooled
250
250 “BC”
21491
22777
22644
23692
30895
31007
31197-1
50891
50967
51024
70496
53015
53016
50770
31470
70438
---------50481
21491
22777
22644
23692
30895
31007
31197-1
50891
50967
52208
70496
53015
53016
50770
31470
70438
30794
50481
PART NUMBERS
Air Cooled
Water Cooled
250
250 “BC”
250
250 “BC”
Contactor
30379
30379
30379
30379
Toggle Switch
30385
30385
30385
30385
Flush Switch
30895
30895
30895
30895
Bin Thermostat
31001
31001
31001
31001
Fuse, 1-1/4 Amps (Gate Solenoid)
31406
31406
31406
31406
Timer, Harvest
31840
31840
31840
31840
Conductivity Control
31743
31743
31743
31743
Capacitor, Harvest Motor
31673
31673
31673
31673
Compressor Start Relay
31671
31671
31671
31671
Capacitor, Compressor Start
31741
31741
31741
31741
Capacitor, Compressor Run
31673
31673
31673
31673
Compressor Overload
31742
31742
31742
31742
High Pressure Control
60501
60501
60501
60501
Low Pressure Control
60369
60369
60369
60369
Transformer, Beverage
----------
31091
----------
31091
Relay, Agitator Motor
31375
31375
31375
31375
90914
34
PARTS LIST (CONT’D)
DESCRIPTION
Refrigeration Components
PART NUMBERS
Air Cooled
250
250 “BC”
Water Cooled
250
250 “BC”
Compressor
60678
60678
60678
60678
Compressor Mounting Kit
31607
31607
31607
31607
Air Pump
31568
31568
31568
31568
Hose Adaptor, 3/8 NPT X 3/8 Barb
51189
51189
51189
51189
Hose Adaptor 90°, 3/8 NPT X 3/8 Barb
51190
51190
51190
51190
Condenser Fan Motor
31738
31738
----------
----------
Condenser Fan Blade
31739
31739
----------
----------
Water Valve Inlet
40672
40672
40672
40672
Condenser Air-Cooled
60679
60679
----------
----------
Condenser Shroud
51388
51388
----------
----------
Tinnerman Clip, Shroud
70704
70704
----------
----------
Filter (Drier)
60623
60623
60623
60623
Hot Gas Solenoid Valve
60620
60620
60620
60620
Hot Gas Solenoid Coil (115 Volt)
32576
32576
32576
32576
TXV R-502
60947
60947
60947
60947
Condenser, Water Cooled
----------
----------
60309
60309
Water Regulating Valve
----------
----------
40122
40122
Water Drain Valve
40653
40653
40653
40653
Tubing, Water Drain, 1/2 inch I.D.
50351
50351
50351
50351
Tubing, Air Pump, 3/8 inch I.D.
50096
50096
50096
50096
PART NUMBERS
DESCRIPTION
Evaporator Components
250
Air Cooled
250 “BC”
Water Cooled
250
250 “BC”
Evaporator Assembly
61023
61023
61023
61023
Evaporator Housing, Foamed
51368
51368
51368
51368
Evaporator Coil Assembly
60680
60680
60680
60680
51369--1
51369--1
51369--1
51369--1
Gasket Kit
51356
51356
51356
51356
Ice Thickness Probe
51179
51179
51179
51179
31560--1
31560--1
31560--1
31560--1
51191
Harvest Bar Assembly With Gaskets
Harvest Motor With Gaskets
Hose Adaptor, 1/4 NPT X 3/8 Barb
51191
51191
51191
Hose Adaptor, 1/4 NPT X 1/2 Barb
51192
51192
51192
51192
10-32 X 5/8 Phillips Flat Head Screw
70746
70746
70746
70746
Miscellaneous Components
Air Cooled
250
250 “BC”
Water Cooled
250
250 “BC”
Filter
70551
70551
70551
70551
Filter Coating, 16 Ounces
51355
51355
51355
51355
Label “Press For Ice”
90906
90906
90906
90906
Wiring Diagram
90915
90915
90915
90915
Manual
90914
90914
90914
90914
Cleaning Label
90916
90916
90916
90916
35
90914
IMI CORNELIUS INC.
ONE CORNELIUS PLACE
ANOKA, MN. 55303--6234
TELEPHONE (800) 238--3600
FACSIMILE (612) 422--3232
TECH SVC 1-800-535-4240
WARRANTY
IMI Cornelius Inc. and Remcor Products Company warrants that all equipment and parts are free from defects
in material and workmanship under normal use and service. For a copy of the warranty applicable to your
Cornelius and or Remcor product, in your country, please write, fax or telephone the IMI Cornelius office nearest you. Please provide the equipment model number, serial number and the date of purchase.
IMI Cornelius Offices
AUSTRALIA D P.O. 210, D RIVERWOOD, D NSW 2210, AUSTRALIA D (61) 2 533 3122 D FAX (61) 2 534 2166
AUSTRIA D AM LANGEN FELDE 32 D A-1222 D VIENNA, AUSTRIA D (43) 1 233 520 D FAX (43) 1-2335-2930
BELGIUM D BOSKAPELLEI 122 D B-2930 BRAASCHAAT, BELGIUM D (32) 3 664 0552 D FAX (32) 3 665 2307
BRAZIL D RUA ITAOCARA 97 D TOMAS COELHO D RIO DE JANEIRO, BRAZIL D (55) 21 591 7150 D FAX (55) 21 593 1829
ENGLAND D TYTHING ROAD ALCESTER D WARWICKSHIRE, B49 6 EU, ENGLAND D (44) 789 763 101 D FAX (44) 789 763 644
FRANCE D 71 ROUTE DE ST. DENIS D F-95170 DEUIL LA BARRE D PARIS, FRANCE D (33) 1 34 28 6200 D FAX (33) 1 34 28 6201
GERMANY D CARL LEVERKUS STRASSE 15 D D-4018 LANGENFELD, GERMANY D (49) 2173 7930 D FAX (49) 2173 77 438
GREECE D 488 MESSOGION AVENUE D AGIA PARASKEVI D 153 42 D ATHENS, GREECE D (30) 1 600 1073 D FAX (30) 1 601 2491
HONG KONG D 1104 TAIKOTSUI CENTRE D 11-15 KOK CHEUNG ST D TAIKOKTSUE, HONG KONG D (852) 789 9882 D FAX (852) 391 6222
ITALY D VIA PELLIZZARI 11 D 1-20059 D VIMARCATE, ITALY D (39) 39 608 0817 D FAX (39) 39 608 0814
NEW ZEALAND D 20 LANSFORD CRES. D P.O. BOX 19-044 AVONDALE D AUCKLAND 7, NEW ZEALAND D (64) 9 8200 357 D FAX (64) 9 8200 361
SINGAPORE D 16 TUAS STREET D SINGAPORE 2263 D (65) 862 5542 D FAX (65) 862 5604
SPAIN D POLIGONO INDUSTRAIL D RIERA DEL FONOLLAR D E-08830 SANT BOI DE LLOBREGAT D BARCELONA, SPAIN D (34) 3 640 2839 D FAX (34) 3 654 3379
USA D ONE CORNELIUS PLACE D ANOKA, MINNESOTA D (612) 421-6120 D FAX (612) 422-3255
36
Manual number
CORPORATE HEADQUARTERS:
Remcor Incorporated
500 Regency Drive
Glendale Heights, IL 60139
708. 980.6900
Download PDF