Eiki | EIP-250 | Owner`s manual | Eiki EIP-250 Owner`s manual

Introduction
Quick Start
®
EIP-2600
EIP-250
Setup
Connections
EIP-2600
EIKI INDUSTRIAL CO., LTD.
Appendix
OWNER’S MANUAL
IMPORTANT
• For your assistance in reporting the loss or theft of your
Projector, please record the Model and Serial Number
located on the bottom of the projector and retain this
information.
• Before recycling the packaging, please ensure that you
have checked the contents of the carton thoroughly against
the list of “Supplied accessories” on page 10.
Model No.:
Serial No.:
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A
fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or
and of the same rating as above, which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied,
cut off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and
disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a
serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow
: Earth
Blue
: Neutral
Brown
: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured
markings identifying the terminals in your plug proceed as follows:
• The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is
marked by the letter E or by the safety earth symbol
or coloured green or green-and-yellow.
• The wire which is coloured blue must be connected to the terminal which is marked with the letter N
or coloured black.
• The wire which is coloured brown must be connected to the terminal which is marked with the letter L or
coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
The supplied CD-ROM contains operation instructions in English, German, French, Spanish, Italian
and Portuguese. Carefully read through the operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Spanisch,
Italienisch und Portugiesisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors
sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français,
espagnol, italien et portugais. Veuillez lire attentivement ces instructions avant de faire fonctionner le
projecteur.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, español,
italiano y portugués. Lea cuidadosamente las instrucciones de operación antes de utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, spagnolo, italiano
e portoghese. Leggere attentamente le istruzioni per l’uso prima di usare il proiettore.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Espanhol, Italiano e
Português. Leia cuidadosamente todas as instruções de operação antes de operar o projetor.
ii
Before using the projector, please read this owner’s manual carefully.
Introduction
ENGLISH
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification,
or recall that EIKI may be required to give under the 1972 Consumer Product Safety Act,
PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
WARNING:
High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the
beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose
this product to rain or moisture.
See bottom of projector.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute
a risk or electric shock to persons.
The exclamation point within a triangle
is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the product.
PRODUCT DISPOSAL
This product utilizes tin-lead solder, and lamp containing a small amount
of mercury. Disposal of these materials may be regulated due to
environmental considerations. For disposal or recycling information,
please contact your local authorities, the Electronics Industries Alliance:
www.eiae.org, the lamp recycling organization www.lamprecycle.org,
or 1-800-242-3454.
U.S.A. ONLY
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 52.
Authorized representative responsible for the European Union Community Market
EIKI Deutschland GmbH
Am Frauwald 12, 65510 Idstein
E.U. ONLY
1
WARNING:
FCC Regulations state that any unauthorized changes or modifications to
this equipment not expressly approved by the manufacturer could void
the user’s authority to operate this equipment.
U.S.A. ONLY
For EIP-2600
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the owner’s manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will be required to
correct the interference at his own expense.
U.S.A. ONLY
The enclosed computer cable must be used with the device. The cable is provided to
ensure that the device complies with FCC Class A verification.
U.S.A. ONLY
WARNING:
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
For EIP-250
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the owner’s manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
U.S.A. ONLY
Declaration of conformity
EIKI PROJECTOR, MODEL EIP-250
This device complies with Part 15 of the FCC rules. Operation is subject to the following
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Responsible Party:
EIKI INTERNATIONAL, INC.
30251 Esperanza Rancho Santa Margarita, CA 92688-2132
TEL: 800-242-3454
2
U.S.A. ONLY
How to Read this Owner’s Manual
■ The specifications are slightly different, depending on the model. However, you can connect and
operate all models in the same manner.
• In this owner’s manual, the illustration and the screen display are simplified for explanation, and
may differ slightly from the actual display. The examples used throughout this manual are based
on the EIP-2600 model.
Using the Menu Screen
ENTER button
Adjustment buttons (P/R/O/Q)
MENU/HELP button
ENTER button
Adjustment buttons
(P/R/O/Q)
RETURN button
• Press RETURN to return
to the previous screen
when the menu is
displayed.
Buttons used in
this operation
MENU/HELP button
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
Button used in
this step
• This operation can also be performed by using the buttons on the projector.
1
Press MENU/HELP.
2
Press Q or O and select “Picture”
to adjust.
• The “Picture” menu screen for the selected input mode is displayed.
Example: “Picture” screen menu for
COMPUTER (RGB) input
(EIP-2600)
Menu item
Picture
SCR - ADJ
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
BrilliantColor TM
C.M.S. Setting
C.M.S.
DNR
Lamp Setting
Reset
SEL./ADJ.
PRJ - ADJ
Help
Standard
0
0
0
0
0
1
On-screen
display
On
Off
Bright
ENTER
END
38
Info
........Indicates safeguards for using the projector.
Note .........Indicates additional information for setting up and operating the
projector.
For Future Reference
Maintenance
P. 49
Troubleshooting
PP. 63 and 64
Index
P. 67
3
Contents
Preparing
Introduction
Useful Features
How to Read this Owner’s Manual ....... 3
Contents ............................................... 4
IMPORTANT SAFEGUARDS ............... 6
How to Access the PDF Owner’s
Manuals .............................................. 9
Accessories ........................................ 10
Part Names and Functions ................. 11
Operating with the Remote Control .... 32
Projector ............................................... 11
Rear View ............................................. 12
Inserting the Batteries .......................... 14
Usable Range ...................................... 15
Quick Start
Menu Items ......................................... 35
Using the Menu Screen ...................... 38
Quick Start .......................................... 16
Menu Selections (Adjustments) ........... 38
Setup and Projection ............................ 16
Picture Adjustment (“Picture” Menu) ... 40
Setup
Setting up the Projector ...................... 18
Setting up the Projector ....................... 18
Standard Setup (Front Projection) ....... 18
Ceiling-mount Setup ............................ 18
Projection (PRJ) Mode ......................... 19
Screen Size and Projection Distance .. 20
Connections
Connecting the Projector to
Other Equipment .............................. 21
Controlling the Projector by
a Computer ....................................... 24
Connecting the Power Cord ............... 24
Using
Basic Operation
Turning the Projector On/Off .............. 25
Turning the Projector on ....................... 25
Turning the Power off (Putting the
Projector into Standby Mode) ........... 25
Image Projection ................................. 26
About the Setup Guide ........................ 26
Adjusting the Projected Image ............ 26
Correcting Trapezoidal Distortion ........ 28
Switching the Input Mode .................... 29
Adjusting the Volume ........................... 29
Displaying the Black Screen and
Turning off the Sound Temporarily .... 29
Resize Mode ......................................... 30
4
Displaying and Setting the
Break Timer ........................................ 32
Displaying the Pointer .......................... 32
Using the Spot Function ...................... 32
Switching the Eco+Quiet Mode ........... 32
Auto Sync (Auto Sync Adjustment) ..... 33
Freezing a Moving Image .................... 33
Selecting the Picture Mode .................. 33
Displaying an Enlarged Portion of
an Image ............................................ 33
Using the Remote Control as the
Wireless Computer Mouse ................ 34
Selecting the Picture Mode .................. 40
Adjusting the Image ............................. 41
Adjusting the Color Temperature ......... 41
Adjusting the Colors ............................. 41
Progressive ........................................... 42
Reducing Image Noise (DNR) ............. 42
Lamp Setting ........................................ 42
Adjusting the Projector Image
(“SCR - ADJ” Menu) ......................... 43
Setting the Resize Mode ...................... 43
Adjusting the Image Position ............... 43
Keystone Correction ............................ 43
Setting the On-screen Display ............. 43
Closed Caption .................................... 44
Selecting the Background Image ........ 44
Selecting the Setup Guide ................... 44
Reversing/Inverting Projected
Images ............................................... 44
Selecting the On-screen Display
Language ........................................... 44
Adjusting the Projector Function
(“PRJ - ADJ” Menu) .......................... 45
Auto Sync (Auto Sync Adjustment) ..... 45
Auto Power Off Function ...................... 45
Auto Restart Function .......................... 45
STANDBY Mode ................................... 45
Setting the Confirmation Sound
(System Sound) ................................. 45
Speaker Setting .................................... 45
Audio Input (EIP-2600 only) ................. 46
Selecting the Transmission Speed
(RS-232C) .......................................... 46
Fan Mode Setting ................................. 46
System Lock Function .......................... 46
Checking the Lamp Life Status ........... 47
Keylock Function .................................. 47
Troubleshooting with the
“Help” Menu ...................................... 48
Utilizing the “Help” Menu Functions .... 48
Reference
Appendix
Maintenance ....................................... 49
Maintenance Indicators ...................... 50
Regarding the Lamp ........................... 52
Lamp ..................................................... 52
Caution Concerning the Lamp ............ 52
Replacing the Lamp ............................. 52
Removing and Installing the
Lamp Unit .......................................... 53
Resetting the Lamp Timer .................... 54
Connecting Pin Assignments ............. 55
RS-232C Specifications and
Commands ....................................... 57
Computer Compatibility Chart ............ 62
Troubleshooting .................................. 63
Specifications ..................................... 65
Dimensions ......................................... 66
Index ................................................... 67
5
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this product
and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the
safeguards incorporated in this product, observe the following basic rules for its installation,
use and servicing.
1. Read Instructions
All the safety and operating instructions should be
read before the product is operated.
2. Retain Instructions
The safety and operating instructions should be
retained for future reference.
3. Heed Warnings
All warnings on the product and in the
operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be
followed.
5. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example,
near a bath tub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a swimming pool;
and the like.
8. Accessories
Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may
fall, causing serious injury to a child or adult, and
serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table recommended
by the manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer’s instructions, and should use a
mounting accessory recommended by the
manufacturer.
9. Transportation
A product and cart
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may
cause the product and cart
combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the
product and to protect it from overheating, and
these openings must not be blocked or covered.
The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar
surface. This product should not be placed in a
built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
6
11. Power Sources
This product should be operated only from the type
of power source indicated on the marking label. If
you are not sure of the type of power supply to
your home, consult your product dealer or local
power company. For products intended to operate
from battery power, or other sources, refer to the
operating instructions.
12. Grounding or Polarization
This product is provided with one of the following
types of plugs. If the plug should fail to fit into the
power outlet, please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with a
grounding terminal.
This plug will only fit into a grounding type power
outlet.
13. Power-Cord Protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit from the
product.
14. Lightning
For added protection for this product during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the
wall outlet and disconnect the cable system. This
will prevent damage to the product due to lightning
and power-line surges.
15. Overloading
Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result
in a risk of fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any
kind on the product.
17. Servicing
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to normal operation.
e. If the product has been dropped or damaged
in any way.
f. When the product exhibits a distinct change in
performance, this indicates a need for service.
19. Replacement Parts
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or
other hazards.
20. Safety Check
Upon completion of any service or repairs to this
product, ask the service technician to perform
safety checks to determine that the product is in
proper operating condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling
only as recommended by the manufacturer.
22. Heat
This product should be situated away from heat
sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that
produce heat.
• DLP® and the DLP logo are registered trademarks of Texas Instruments and BrilliantColorTM is a
trademark of Texas Instruments.
• Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States
and/or other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the United States.
• Adobe® Reader® is a trademark of Adobe Systems Incorporated.
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
• All other company or product names are trademarks or registered trademarks of their respective companies.
• Some IC chips in this product include confidential and/or trade secret property belonging to Texas
Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse
assemble or discompile the contents thereof.
Closed Caption uses Bitstream Vera fonts
Copyright (c) 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera is a trademark of
Bitstream, Inc.
Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts
accompanying this license (“Fonts”) and associated documentation files (the “Font Software”), to
reproduce and distribute the Font Software, including without limitation the rights to use, copy,
merge, publish, distribute, and/or sell copies of the Font Software, and to permit persons to whom
the Font Software is furnished to do so, subject to the following conditions:
The above copyright and trademark notices and this permission notice shall be included in all copies
of one or more of the Font Software typefaces.
The Font Software may be modified, altered, or added to, and in particular the designs of glyphs or
characters in the Fonts may be modified and additional glyphs or characters may be added to the
Fonts, only if the fonts are renamed to names not containing either the words “Bitstream” or the
word “Vera”.
This License becomes null and void to the extent applicable to Fonts or Font Software that has been
modified and is distributed under the “Bitstream Vera” names.
The Font Software may be sold as part of a larger software package but no copy of one or more of
the Font Software typefaces may be sold by itself.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK,
OR OTHER RIGHT. IN NO EVENT SHALL BITSTREAM OR THE GNOME FOUNDATION BE LIABLE FOR
ANY CLAIM, DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR
OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR
FROM OTHER DEALINGS IN THE FONT SOFTWARE.
Except as contained in this notice, the names of Gnome, the Gnome Foundation, and Bitstream
Inc., shall not be used in advertising or otherwise to promote the sale, use or other dealings in this
Font Software without prior written authorization from the Gnome Foundation or Bitstream Inc.,
respectively. For further information, contact: fonts at gnome dot org.
7
Observe the following safeguards when setting up your
projector.
Caution concerning the lamp unit
■ Potential hazard of glass particles if lamp ruptures. In case
of lamp rupture, contact your
nearest EIKI Author ized
Dealer or Service Center for
replacement.
See “Regarding the Lamp” on
page 52.
Caution concerning the setup of the
projector
■ For minimal servicing and to maintain high
image quality, EIKI recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the
projector is subjected to these environments,
the vents and lens must be cleaned more often. As long as the projector is regularly
cleaned, use in these environments will not
reduce the overall operation life of the unit.
Internal cleaning should only be performed
by an EIKI Authorized Dealer or Service Center.
Do not set up the projector in places
exposed to direct sunlight or bright light.
■ Position the screen so that it is not in direct
sunlight or room light. Light falling directly on
the screen washes out the colors, making
viewing difficult. Close the curtains and dim
the lights when setting up the screen in a
sunny or bright room.
Caution regarding placing of the projector
■ Place the projector on a level site within the
adjustment range (9 degrees) of the adjustment foot.
■ After the projector is purchased, a faint smell
from the vent may appear when the power is
first turned on. This is normal and is not a
malfunction. It will disappear after the projector is used for a while.
8
When using the projector in high-altitude
areas such as mountains (at altitudes of
approximately 1,500 meters (4,900 feet)
or more)
■ When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to “High”.
Neglecting this can affect the longevity of the
optical system.
Warning about placing the projector in
a high position
■ When placing the projector in a high position,
make certain it is carefully secure to avoid
personal injury caused by the projector falling down.
Do not subject the projector to hard
impact and/or vibration.
■ Protect the lens so as not to hit or damage
the surface of the lens.
Rest your eyes occasionally.
■ Continuously watching the screen for long
hours will cause eye strain. Take regular
breaks to rest your eyes.
Avoid locations with extremes of
temperature.
■ The operating temperature of the projector is
from 41°F to 95°F (+5°C to +35°C).
■ The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake
vents.
■ Allow at least 11 13/16 inches (30 cm) of space
between the exhaust vent and the nearest
wall or obstruction.
■ Ensure that the intake vent and the exhaust
vent are not obstructed.
■ If the cooling fan becomes obstructed, a protection circuit will automatically put the projector into standby mode to prevent overheat
damage. This does not indicate a malfunction. (See pages 50 and 51.) Remove the projector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where
the intake and exhaust vents are not blocked,
plug the power cord back in and turn on the
projector. This will return the projector to the
normal operating condition.
Caution regarding usage of the projector
Using the projector in other countries
■ If you are not to use the projector for a long
time or before moving the projector, make
certain you unplug the power cord from the
wall outlet, and disconnect any other cables
connected to it.
■ If the power cord is unplugged while the cooling fan is running, some parts of the projector may still be hot. Use caution when handling the projector.
■ Do not carry the projector by holding the lens.
■ When storing the projector, ensure you attach the lens cap to the projector. (See page
11.)
■ Do not expose the projector to direct sunlight
or place next to heat sources. Doing so may
affect the cabinet color or cause deformation
of the plastic cover.
■ The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, make
sure you use an appropriate power cord for
the country you are in.
Other connected equipment
■ When connecting a computer or other audiovisual equipment to the projector, make the
connections AFTER unplugging the power
cord of the projector from the AC outlet and
turning off the equipment to be connected.
■ Please read the owner’s manuals of the projector and the equipment to be connected for
instructions on how to make the connections.
Temperature monitor function
■ If the projector starts to overheat due to setup
problems or blockage of the air vents, “
” and
“
” will illuminate in the lower left corner
of the picture. If the temperature continues to
rise, the lamp will turn off, the temperature warning indicator on the projector will blink, and after
a 60-second cooling-off period the projector will
enter standby mode. Refer to “Maintenance Indicators” on page 50 for details.
Info
• The cooling fan regulates the internal temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the
fan speed. This does not indicate malfunction.
How to Access the PDF Owner’s Manuals
PDF owner’s manuals in several languages are included in the CD-ROM. To utilize
these manuals, you need to install Adobe® Reader® on your computer (Windows®
or Macintosh®).
Please download Adobe® Reader® from the Internet (http://www.adobe.com).
Accessing the PDF Manuals for Windows® (For Macintosh®, skip step 2).
1
2
3
4
5
Insert the CD-ROM in the CD-ROM drive.
Double click the “My Computer” icon.
Double click the “CD-ROM” drive.
Double click the “MANUALS” folder.
Double click the model (name of the folder)
that you want to view.
6 Double click the language (name of the
folder) that you want to view.
7 Double click the pdf file to access the projector manuals.
Note
• If the desired pdf file cannot be opened by double clicking the mouse, start Adobe® Reader® first,
then specify the desired file using the “File”, “Open” menu.
9
Accessories
Supplied accessories
Two R-6 batteries
(“AA” size, UM/SUM-3,
HP-7 or similar)
RGB cable
(10' (3.0 m))
<QCNWGA045WJPZ>
Lens cap (attached)
DIN-D-sub RS-232C adaptor
(5 57/64" (15 cm))
<QCNWGA091WJPZ>
Remote control
for EIP-2600
for EIP-250
Power cord*
(1)
3 RCA to mini D-sub 15 pin cable
(10' (3.0 m))
<QCNWGA043WJPZ>
(2)
For U.S. and Canada, etc.
(6' (1.8 m))
<QACCDA007WJPZ>
For Europe, except U.K.
(6' (1.8 m))
<QACCVA011WJPZ>
* Use the power cord that corresponds to
the wall outlet in your country.
• QUICK GUIDE
• Owner’s manual (this manual and CD-ROM)
Optional accessories
■ Lamp unit
■ Storage case
10
AH-62101
AH-62501
Part Names and Functions
Numbers in Z refer to the main pages in this owner’s manual where the topic is
explained.
Projector
Top View
Power
indicator
25, 50
STANDBY/ON
button
For turning the
power on and
putting the
projector into
standby mode.
25
ENTER button
For setting
items selected
or adjusted on
the menu.
38
25, 50
50
Temperature warning
indicator
32
ECO+QUIET button
For lowering the noise
of the cooling fan and
extending the lamp life.
29
VOL (Volume) buttons
(–O/Q+)
For adjusting the
speaker sound level.
29
INPUT buttons (P/R)
For switching input mode.
38, 48
KEYSTONE
28
button
For entering the
Keystone
Correction mode.
Front View
Lamp indicator
38
MENU/HELP button
For displaying
adjustment and
setting screens, and
help screen.
Adjustment buttons
(P/R/O/Q)
For selecting menu items.
Zoom ring
26
For enlarging/
reducing the picture.
Remote control
sensor
15
Exhaust vent
49
HEIGHT
ADJUST lever
27
49
Intake vent
45
Speaker
26
Focus ring
For adjusting
the focus.
Push both sides of the lens cap
to attach or remove.
11
Part Names and Functions (Continued)
Numbers in Z refer to the main pages in this owner’s manual where the topic is
explained.
Rear View
Terminals
*AUDIO 1 input terminal
23
COMPUTER/
21
COMPONENT input
22
terminal
Terminal for computer RGB
and component signals.
22
S-VIDEO input terminal
Terminal for connecting
video equipment with an
S-video terminal.
24
*DVI-I input
21
terminal
22
Terminal for
DVI digital,
computer RGB
and component
signals.
RS-232C terminal
Terminal for
controlling the
projector using a
computer.
34
USB terminal
Terminal connecting
with the USB
terminal on the
computer for using
the supplied remote
control as the
computer mouse.
*AUDIO OUT 23
terminal
Audio output terminal of
equipment connected to the
audio input terminal.
MONITOR OUT 23
terminal
(Output terminal for computer RGB,
component signals. Shared for COMPUTER/COMPONENT)
Terminal for connecting a monitor.
23
AUDIO 2 input
terminal
(AUDIO input
terminal for
EIP-250)
22
VIDEO input
terminal
Terminal for
connecting video
equipment.
* EIP-2600 only
24
Rear
adjustment
foot
27
AC socket
Connect the supplied
power cord.
Kensington Security
Standard connector
Using the Kensington Lock
• This projector has a Kensington Security Standard connector for use with a Kensington
MicroSaver Security System. Refer to the information that came with the system for
instructions on how to use it to secure the projector.
12
STANDBY button
25
For putting the projector
into the standby mode.
25 ON button
29
COMPUTER, *DVI,
S-VIDEO, VIDEO buttons
For switching to the
respective input modes.
33 FREEZE button
BREAK TIMER button 32
For displaying the
break time.
MAGNIFY buttons
33
For enlarging/reducing
part of the image.
PAGE UP/PAGE
34
DOWN buttons
Same as the [Page Down] and
[Page Up] keys on a computer
keyboard, when with the USB
connection (using a USB cable
or the optional remote
receiver).
POINTER button
For displaying the
pointer.
32
MOUSE/Adjustment
buttons (P/R/O/Q)
34
38
• For moving the
computer cursor when with the USB
connection (using a USB cable or the
optional remote receiver).
• For selecting and adjusting menu
items.
L-CLICK/EFFECT
button
34
32
For turning the power
on.
For freezing images.
29 AV MUTE button
For temporarily
displaying a black
screen and turning
off the sound.
29 VOL +/– (Volume)
buttons
For adjusting the
speaker sound level.
32 SPOT button
For displaying the
spotlight.
38 ENTER button
For setting items
selected or adjusted
on the menu.
34 R-CLICK/RETURN
button
38 • For the Right click
when with the USB
connection (using a
USB cable or the
optional remote
receiver).
• For returning to the
previous menu screen
during menu
operations.
• For the Left click
when with the USB connection
(using a USB cable or the optional
remote receiver).
• For changing the pointer or spot
area.
38 MENU/HELP button
displaying
48 For
adjustment and
KEYSTONE button
28
For entering the
Keystone Correction mode.
30 RESIZE button
setting screens, and
help screen.
For switching the
picture size
(NORMAL, BORDER,
etc.).
AUTO SYNC button
33
For automatically
adjusting images when
connected to a computer.
33 PICTURE MODE
ECO+QUIET button
32
For lowering the noise
of the cooling fan and
extending the lamp life.
* EIP-2600 only
button
For selecting the
appropriate picture.
13
Part Names and Functions (Continued)
Inserting the Batteries
1
Pull down the tab on the cover and remove the cover
towards the direction of the arrow.
2
Insert the batteries.
3
Insert the lower tab of the cover into the opening,
and lower the cover until it clicks in place.
• Insert the batteries making sure the polarities correctly match
the m and n marks inside the battery compartment.
Incorrect use of the batteries may cause them to leak or explode. Please
follow the precautions below.
Caution
•
•
•
•
•
•
•
•
14
Danger of explosion if battery is incorrectly replaced.
Replace only with alkaline or manganese batteries.
Insert the batteries making sure the polarities correctly match the m and n marks inside the battery
compartment.
Batteries of different types have different properties, therefore do not mix batteries of different types.
Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
Remove the batteries from the remote control once they have run out, as leaving them in can cause them
to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove
them using a cloth.
The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
Remove the batteries from the remote control if you will not be using the remote control for a long time.
Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
Remote control sensor
Usable Range
The remote control can be used to control the
projector within the ranges shown in the
illustration.
Note
• The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may
differ depending on the screen material.
30°
When using the remote control
• Ensure that you do not drop it or expose it to
moisture or high temperature.
• The remote control may malfunction under a
fluorescent lamp. In this case, move the projector away from the fluorescent lamp.
30°
23n (7 m)
Remote control
signal transmitters
Remote control
15
Quick Start
This section shows the basic operation (projector connecting with the computer). For details, see
the page described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
3
8
6
STANDBY/ON
button
INPUT buttons
4
ENTER button
8 STANDBY button
3 ON button
6 COMPUTER button
5
Adjustment buttons
(P/R/O/Q)
5
4
KEYSTONE
button
Zoom ring
4
Focus ring
5
4
HEIGHT
ADJUST lever
5 KEYSTONE button
4 ENTER button
1. Place the projector facing a wall or a screen
Adjustment buttons
(P/R/O/Q)
_P. 18
2. Connect the projector to the computer and plug the power cord
into the AC socket of the projector
When connecting equipment other than a computer, see
pages 22 and 23.
_PP. 21, 24
3. Remove the lens cap and turn the projector on
On the projector
On the remote control
_P. 25
16
4. Adjust the projected image with the Setup Guide
1 After the projector turns on, the Setup Guide appears.
(When “Setup Guide” is set to “On”. See page 44.)
2 Follow the steps in the Setup Guide and adjust the focus, height (angle) and picture size.
3 After adjusting the focus, height (angle) and picture size, press ENTER to finish the Setup
Guide.
_PP. 26, 27
5. Correct trapezoidal distortion
Correcting trapezoidal distortion using Keystone Correction.
On the projector
Shrinks
upper side.
Shrinks
lower side.
On the remote control
_P. 28
6. Select the INPUT mode
Select the “COMPUTER” using INPUT on the projector or COMPUTER on the remote control.
On the On the remote
control
projector
On-screen display (RGB)
INPUT list
INPUT
COMPUTER
COMPUTER
D
DVI-D Computer
D
DVI-D Video
*
RGB
1024 × 768
*EIP-2600 only
• When you press INPUT on the projector, the INPUT list appears.
Press '/" to switch the INPUT mode.
_P. 29
7. Turn the computer on
8. Turn the power off
Press STANDBY/ON on the projector or STANDBY on the remote control, and then press the
button again while the confirmation message is displayed to put the projector into standby mode.
On the On the remote
projector
control
On-screen display
_P. 25
17
Setting up the Projector
Setting up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet
flat and level. Doing so will eliminate the need for Keystone correction and provide the best image
quality. (See page 28.)
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen according
to the desired picture size. (See page 20.)
Example of standard setup
Side View
Screen
H
Lens center
L
Note
• Refer to page 20 for additional information concerning “Screen Size and Projection Distance”.
Ceiling-mount Setup
■ It is recommended that you use the optional
EIKI ceiling-mount adaptor and unit for this
installation. Before mounting the projector,
contact your nearest EIKI Authorized Dealer
or Service Center to obtain the recommended
ceiling-mount adaptor and unit (sold
separately).
18
Projection (PRJ) Mode
The projector can use any of the 4 projection modes shown in the diagram below. Select the mode
most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-ADJ” menu.
See page 44.)
■ Table mounted, front projection
[Menu item ➞ “Front”]
■ Ceiling mounted, front projection
[Menu item ➞ “Ceiling + Front”]
■ Table mounted, rear projection
(with a translucent screen)
[Menu item ➞ “Rear”]
■ Ceiling mounted, rear projection
(with a translucent screen)
[Menu item ➞ “Ceiling + Rear”]
Indication of the Projection Image Size and Projection Distance
Example: NORMAL Mode (4:3)
Picture Size
300"
240"
×180
200"
40"
"
"×12
80"×
64"× 60"
48"
32"×
24"
0"
4'
(1 11
.5 "–
m 5'
– 8"
9' 1.7
1
m
(3 0
)
.0 "–
m 11
– '4
3. "
5
12
m
)
(3 '3
.7 "–
m 14
– '2
4. "
3
24
m
)
(7 '7
.5 "–
m 28
– '4
8. "
6
m
)
36
(1 '1
1. 0
2 "
m
)
100"
80"
160
Projection
Distance
19
Setting up the Projector (Continued)
Screen Size and Projection Distance
NORMAL Mode (4:3)
Picture (Screen) size
Diag. [χ ]
Width
Projection distance [L]
Height
Minimum [L1]
Maximum [L2]
300 (762 cm) 610 cm (240) 457 cm (180) 11.2 m (36 10)
Distance from the lens center
to the bottom of the image [H]
19 cm (7 9/16)
—
250 (635 cm) 508 cm (200) 381 cm (150)
9.4 m (30 9) 10.8 m (35 5)
16 cm (6 19/64)
200 (508 cm) 406 cm (160) 305 cm (120)
7.5 m (24 7)
8.6 m (28 4)
13 cm (5 3/64)
150 (381 cm) 305 cm (120) 229 cm (90)
5.6 m (18 5)
6.5 m (21 3)
10 cm (3 25/32)
120 (305 cm) 244 cm (96)
183 cm (72)
4.5 m (14 9)
5.2 m (17 0)
8 cm (3 1/32)
100 (254 cm) 203 cm (80)
152 cm (60)
3.7 m (12 3)
4.3 m (14 2)
6 cm (2 33/64)
80 (203 cm) 163 cm (64)
122 cm (48)
3.0 m (9 10)
3.5 m (11 4)
5 cm (2 1/64)
70 (178 cm) 142 cm (56)
107 cm (42)
2.6 m (8 7)
3.0 m (9 11)
4 cm (1 49/64)
60 (152 cm) 122 cm (48)
91 cm (36)
2.2 m (7 4)
2.6 m (8 6)
4 cm (1 33/64)
40 (102 cm) 81 cm (32)
61 cm (24)
1.5 m (4 11)
1.7 m (5 8)
3 cm (1 1/64)
χ : Picture size (diag.) (in/cm)
L: Projection distance (m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
The formula for picture size and projection distance
[m/cm]
[Feet/inches]
L1 (m) = 0.03745χ
L1 (ft) = 0.03745χ / 0.3048
L2 (m) = 0.04323χ
L2 (ft) = 0.04323χ / 0.3048
χ
H (cm) = 0.064
H (in) = 0.064χ / 2.54
STRETCH Mode (16:9)
Picture (Screen) size
Diag. [χ ]
Width
Height
Projection distance [L]
Minimum [L1]
Maximum [L2]
Distance from the lens center to Adjustable range of
the bottom of the image [H]
image position [S]
250 (635 cm) 553 cm (218)
311 cm (123) 10.2 m (33 6) 11.8 m (38 8)
69 cm (27 19/64)
52 cm (20 27/64)
200 (508 cm) 443 cm (174)
249 cm (98)
8.2 m (26 9)
9.4 m (30 11)
55 cm (21 53/64)
42 cm (16 11/32)
150 (381 cm) 332 cm (131)
187 cm (74)
6.1 m (20 1)
7.1 m (23 2)
42 cm (16 3/8)
31 cm (12 1/4)
120 (305 cm) 266 cm (105)
149 cm (59)
4.9 m (16 1)
5.7 m (18 7)
33 cm (13 3/32)
25 cm (9 13/16)
100 (254 cm) 221 cm (87)
125 cm (49)
4.1 m (13 5)
4.7 m (15 5)
28 cm (10 59/64)
21 cm (8 11/64)
80 (203 cm) 177 cm (70)
100 cm (39)
3.3 m (10 9)
3.8 m (12 4)
22 cm (8 47/64)
17 cm (6 17/32)
60 (152 cm) 133 cm (52)
75 cm (29)
2.4 m (8 0)
2.8 m (9 3)
17 cm (6 35/64)
12 cm (4 29/32)
40 (102 cm)
50 cm (20)
1.6 m (5 4)
1.9 m (6 2)
11 cm (4 23/64)
8 cm (3 17/64)
89 cm (35)
χ : Picture size (diag.) (in/cm)
L: Projection distance (m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
S: Adjustable range of image position (cm/in) See page 43.
The formula for picture size and projection distance
[Feet/inches]
[m/cm]
L1 (ft) = 0.0408χ / 0.3048
L1 (m) = 0.0408χ
L2 (ft) = 0.0471χ / 0.3048
L2 (m) = 0.0471χ
χ
H (in) = 0.27727χ / 2.54
H (cm) = 0.27727
S (in) = ±0.20754χ / 2.54
S (cm) = ±0.20754χ
Note
• Refer to page 18 concerning “Projection distance [L]” and “Distance from the lens center to the
bottom of the image [H]”.
• Allow a margin of error in the values in the diagrams above.
20
Connecting the Projector to Other Equipment
Before connecting, ensure that the power cord of the projector is unplugged from the AC
outlet and turn off the equipment to be connected. After making all connections, turn on the
projector and then the other pieces of equipment. When connecting a computer, ensure that
it is the last equipment to be turned on after all the connections are made.
IMPORTANT:
Ensure that the appropriate input mode has been selected on the projector before
you turn on the connected equipment.
• For more details of connection and cables, refer to the owner’s manual of the connecting equipment.
• You may need other cables or connectors not listed below.
Terminals on the Projector
Example: Terminals of EIP-2600
Equipment
Computer
Terminal on
connected equipment
Cable
RGB
output
terminal
RGB cable (supplied)
RGB
output
terminal
mini D-sub 15 pin to DVI cable
(commercially available)
Terminal on the
projector
COMPUTER/
COMPONENT
DVI-I
DVI digital
output
terminal
DVI Digital cable (commercially available)
is only for EIP-2600.
Note
• See page 62 “Computer Compatibility Chart” for a list of computer signals compatible with the projector. Use with computer signals other than those listed may cause some of the functions to not work.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Macintosh Dealer.
• Depending on the computer you are using, an image may not be projected unless the
computer’s external output port is switched on. Refer to the specific instructions in your computer
owner’s manual to enable your computer’s external output port.
21
Connecting the Projector to Other Equipment (Continued)
Equipment
Video equipment
Terminal on
Cable
connected equipment
HDMI to DVI cable
HDMI
(commercially available)
output
terminal
DVI digital
output
terminal
Terminal on the
projector
DVI-I
DVI Digital cable (commercially available)
3 RCA to mini D-sub 15 pin cable
(supplied)
COMPUTER/
COMPONENT
S-video
output
terminal
S-video cable (commercially available)
S-VIDEO
Video
output
terminal
Video cable (commercially available)
VIDEO
Cables for a camera or a video game/3 RCA
to mini D-sub 15 pin cable (supplied)
COMPUTER/
COMPONENT
Component
video
output
terminal
Camera/Video game
Component
video
output
terminal
RCA adaptor plug
(commercially available)
Cables for a camera or a video game
S-VIDEO
S-video
output
terminal
Cables for a camera or a video game
VIDEO
Video
output
terminal
is only for EIP-2600.
Note
• Only for EIP-2600:
- While the projector is connected to video equipment that has an HDMI output terminal, only the
video signal can be input to the projector. (Connect the AUDIO input terminal for audio input.)
- Depending on specifications of video equipment or HDMI to DVI digital cable, the signal transmission may not work property. (The HDMI specification does not support all connections to video
equipment that has HDMI digital output terminal using HDMI to DVI digital cable.)
- For details on compatibility for connection, see support information on DVI connection provided
by the video equipment manufacturer.
• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a
commercially available cable that fits in the projector terminal you want to connect.
• The projector does not support RGBC signals via the Euro-scart.
22
Equipment
Audio equipment
Terminal on
connected equipment
Cable
ø3.5 mm stereo or mono audio cable
ø3.5 mm
audio output (commercially available)
terminal
RCA audio
output
terminal
RCA audio cable (commercially available)
Terminal on the
projector
AUDIO 1
AUDIO 2 (EIP-2600)
AUDIO (EIP-250)
Cables for a camera or a video game
Audio
output
terminal
Monitor
Amplifier
RGB
input
terminal
RGB cable (supplied or commercially
available)
ø3.5 mm
audio input
terminal
ø3.5 mm stereo or mono audio cable
(commercially available)
RCA audio
input
terminal
MONITOR OUT
AUDIO OUT
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
is only for EIP-2600.
Note
• Only for EIP-2600:
- When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5
mm stereo audio cable.
- You can select “Audio 1” or “Audio 2” for “Audio Input” in the “PRJ-ADJ” menu. (See page 46.)
• RGB signals and Component signals can be output to the monitor.
23
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS232C adaptor and an RS-232C serial control cable (cross type, commercially available), the computer can be used to control the projector and check the status of the projector. See page 57 for
details.
When connecting to a computer using an RS-232C serial control cable and a DIND-sub RS-232C adaptor
To RS-232C terminal
DIN-D-sub RS-232C
adaptor (supplied)
Computer
To RS-232C terminal
RS-232C serial control cable (cross type, commercially available)
Note
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
owner’s manual of the computer for details.
• See page 56 for connection of an RS-232C serial control cable.
Info
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This
may damage your computer or projector.
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.
This may damage your computer.
Connecting the Power Cord
Plug the supplied power cord into the
AC socket on the rear of the projector.
Then plug into AC outlet.
AC socket
To AC outlet
24
Power cord
(supplied)
Turning the Projector On/Off
Info
Turning the Projector on
Note that the connections to external equipment and power outlet should be done before performing the operations written below. (See pages 21 to 24.)
Remove the lens cap and press
STANDBY/ON on the projector or ON
on the remote control.
• When “Auto Restart” is set to “On”:
If the power cord is unplugged from the outlet
or the breaker switch is turned off when the
projector is on, then the projector automatically turns on when the power cord is plugged
into the AC outlet or the breaker switch is
turned on. (See page 45.)
• English is the factory default language. If you
want to change the on-screen display to another language, change the language according to the procedure on page 44.
• The power indicator illuminates red.
• After the lamp indicator illuminates, the projec-
Lamp indicator
tor is ready to start operation.
Power indicator
Note
• About the Lamp Indicator
The lamp indicator illuminates to indicate the
status of the lamp.
Green: The lamp is on.
Blinking in green: The lamp is warming up.
Red: The lamp is shut down abnormally
or the lamp should be replaced.
• When switching on the projector, a slight flickering of the image may be experienced within
the first minute after the lamp has been illuminated. This is normal operation as the lamp’s
control circuitry is stabilising the lamp output
characteristics. It should not be regarded as
faulty operation.
• If the projector is put into standby mode and
immediately turned on again, the lamp may
take some time to start projection.
• When System Lock is set, the keycode input box
appears. To cancel the keycode setting, input
the keycode that you have already set. See page
46 for details.
STANDBY/ON button
STANDBY
button
ON button
On-screen display (confirmation message)
Turning the Power off (Putting
the Projector into Standby Mode)
Press STANDBY/ON on the projector or
STANDBY on the remote control, then
press that button again while the confirmation message is displayed, to put the
projector into standby mode.
• The projector cannot be turned on while cooling.
Info
• Direct Power Off function:
You can unplug the power cord from the AC outlet even if the cooling fan is still running.
25
Image Projection
Setup Guide screen
About the Setup Guide
After turning on the projector, the Setup
Guide screen appears to assist you with
projector setup.
Guidance items
1 FOCUS
2 HEIGHT ADJUST
3 ZOOM
Press ENTER to exit the Setup Guide
screen.
Note
• The Setup Guide screen automatically highlights the items in the following order:
1 FOCUS
4 ENTER
2 HEIGHT ADJUST
3 ZOOM
However, you can adjust the focus, height
(angle), or zoom regardless of the highlighted
item.
• If you do not want to display the Setup Guide
for the next time, set “Menu” - “SCR - ADJ” “Setup Guide” to “Off”. (See page 44.)
STANDBY/ON
button
ENTER button
Zoom ring
Adjusting the Projected Image
1 Adjusting the Focus
You can adjust the focus with the focus
ring on the projector.
Rotate the focus ring to adjust the focus while watching the projected image.
2 Adjusting the Picture Size
You can adjust the picture size using
the zoom ring on the projector.
Rotate the zoom ring to enlarge or
shrink the picture size.
26
Focus ring
3 Adjusting the Height
The height of the projector can be adjusted using the adjustment feet at the
front and rear of the projector.
When the screen is above the projector, the projection image can be made
higher by adjusting the projector.
1
Lift the projector to adjust its
height while lifting the HEIGHT
ADJUST lever.
2
Remove your hands from the
HEIGHT ADJUST lever of the projector after its height has been
finely adjusted.
HEIGHT
ADJUST lever
• The angle of projection is adjustable up
to 9 degrees from the surface on which
the projector is placed.
3
Use the rear adjustment foot to
make the projector level.
Make small
adjustments.
• The projector is adjustable ±2 degrees
from the standard position.
Note
• When adjusting the height of the projector,
trapezoidal distortion occurs. Follow the procedures in Keystone Correction to correct the
distortion. (See pages 28 and 43.)
Rear adjustment foot
Info
• Do not apply too much pressure on the projector when the front adjustment foot comes
out.
• When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
• Hold the projector firmly while lifting or carrying.
• Do not hold by the lens area.
27
Image Projection (Continued)
Correcting Trapezoidal
Distortion
Adjustment buttons
(P/R/O/Q)
When the image is projected either from
the top or from the bottom towards the
screen at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is
called Keystone Correction.
Note
• The Keystone Correction can be adjusted up
to an angle of approximately ±40 (EIP-2600)/
±20 (EIP-250) degrees and the screen can
also be set up to an angle of approximately
±40 (EIP-2600)/±20 (EIP-250) degrees (when
the resize mode is set to “NORMAL” (see page
30)).
1
KEYSTONE button
On-screen display
(Keystone Correction mode)
KEYSTONE
ADJUST
Press KEYSTONE to enter the
Keystone Correction mode.
• You can also display the on-screen display of the Keystone Correction mode
with KEYSTONE on the projector.
2
RETURN button
0
END
Shrinks upper side.
(Move the slide bar in the + direction.)
Press P/Q or O/R to adjust the
Keystone Correction.
• You can also adjust the Keystone Correction using the adjustment buttons on
the projector.
Shrinks lower side.
(Move the slide bar in the - direction.)
Note
• To return to the default setting, press RETURN
while the on-screen display of the Keystone
Correction mode is on the screen.
3
28
Press KEYSTONE.
• The on-screen display of the Keystone
Correction mode will disappear.
• You can also use KEYSTONE on the projector.
Info
• While adjusting the image using Keystone
Correction, straight lines and the edges of the
image may appear jagged.
COMPUTER,
DVI (EIP-2600 only),
S-VIDEO, VIDEO buttons
Switching the Input Mode
Select the appropriate input mode for
the connected equipment.
AV MUTE button
Press COMPUTER, DVI (EIP-2600
only), S-VIDEO or VIDEO on the remote
control to select the input mode.
VOL +/– (Volume)
buttons
• When you press INPUT on the projector or DVI
on the remote control (EIP-2600 only), the INPUT
list appears.
Press P/R to switch the INPUT mode.
Adjusting the Volume
Press VOL +/– on the remote control or
–O/Q+ on the projector to adjust the volume.
Note
• Pressing VOL–/–O will lower the volume.
• Pressing VOL+/Q+ will raise the volume.
• When the projector is connected to external
equipment, the volume level of the external equipment changes in accordance with the volume
level of the projector. Set the projector’s volume
to the lowest level when turning the projector on/
off or when changing the input signal.
• When you do not want to output the sound from
the projector’s speaker while the projector is connected to external equipment, set “Speaker” in
“PRJ-ADJ” menu to “Off”. (See page 45.)
On-screen display
Displaying the Black Screen
and Turning off the Sound
Temporarily
Press AV MUTE on the remote control
to temporarily display a black screen
and turn off the sound.
On-screen display
Note
• Pressing AV MUTE again will turn the projected image back on.
29
Image Projection (Continued)
Resize Mode
This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose a desired image.
Press RESIZE.
RESIZE
button
• See page 43 for setting on menu screen.
COMPUTER
Main resolution
SVGA (800 x 600)
FULL
NORMAL
DOT BY DOT
800 x 600
1024 x 768
STRETCH
BORDER
768 x 576
XGA (1024 x 768)
EIP-2600
1024 x 576
SXGA (1280 x 1024)
968 x 768
1280 x 800
1024 x 640
SVGA (800 x 600)
1024 x 768
720 x 576
1280 x 800
922 x 576
600 x 450
800 x 600
1024 x 768
XGA (1024 x 768)
EIP-250
1280 x 1024
SXGA (1280 x 1024)
750 x 600
1280 x 800
800 x 500
1280 x 800
Input signal
800 x 450
1280 x 1024
800 x 600
For 4:3 screen
720 x 450
For 16:9 screen
Computer
Image type
EIP-2600
EIP-250
NORMAL
FULL
DOT BY DOT
BORDER
STRETCH
Resolution Resolution
lower than lower than
XGA
SVGA
XGA
SVGA
Resolution
higher than
XGA
Resolution
higher
than
SVGA
*2
4:3 aspect ratio
*2
*1, *3
*1
SXGA (1280 × 1024)
5:4 aspect ratio
*1
1280 × 720
1360 × 768
1366 × 768
1
*
*23
*
30
*2
16:9 aspect ratio
1280 × 768
1280 × 800
*2
*1
*1
*1
16:10 aspect ratio
: Cutout area on which images cannot be projected
: Area where the signals are off screen
The Image Shift function can be used for these images.
Same as NORMAL mode.
For EIP-250 model, “Border” cannot be selected with certain resolution selections in which the horizontal part of aspect ratio becomes smaller than
4:3 (such as 1280 × 1024, among others).
VIDEO
VIDEO/DTV
Input signal
Video/DTV
For 4:3 screen
Image type
NORMAL
AREA ZOOM
For 16:9 screen
V-STRETCH
BORDER
STRETCH
1
*
*1
*1
*1
*1
*1
4:3 aspect ratio
480I, 480P,
576I, 576P,
NTSC, PAL,
SECAM
Squeeze
Letter box
720P, 1035I,
1080I, 1080P
16:9 aspect ratio
*1
*2
*2
16:9 aspect ratio
540P
*1
(4:3 aspect ratio in 16:9)
: Cutout area on which images cannot be projected
: Area on which the image is not included in the original signals
*1 The Image Shift function can be used for these images.
*2 Same as NORMAL mode.
About Copyrights
• When using the RESIZE function to select an image size with a different aspect ratio to
a TV program or video image, the image will look different from its original appearance.
Keep this in mind while choosing an image size.
• The use of the Resize or Keystone Correction function to compress or stretch the image
for commercial purposes/public displays in a café, hotel, etc. may be an infringement of
copyright protected by law for copyright holders. Please use caution.
31
Operating with the Remote Control
BREAK TIMER button
FREEZE button
MAGNIFY buttons
Displaying the Pointer
POINTER button
Press POINTER and press P/R/
O/Q on the remote control to move
the pointer.
SPOT button
• Press EFFECT to change the pointer icon
(5 types).
Adjustment buttons
(P/R/O/Q)
EFFECT button
PICTURE MODE button
ECO+QUIET button
1
Star
2
Finger1
Finger2
Heart
Underline
Press POINTER again.
• The pointer will disappear.
AUTO SYNC button
Using the Spot Function
Displaying and Setting the
Break Timer
1
1
Press SPOT and press P/R/O/Q
on the remote control to move the
spot area.
• Press EFFECT to change the spot area
size (3 types).
Press BREAK TIMER.
• The timer starts to count down from 5
minutes.
1/9
1/25
1/8
On-screen display
2
Press P /R /O /Q to adjust the
length of the break time.
• Increases with P or Q
2
Press SPOT again.
• The spot area will disappear.
5 minutes s 6 minutes s 60 minutes
• Shortens with O or R
4 minutes s 3 minutes s1 minute
• The break time can be set in units of one
minute (up to 60 minutes).
Canceling the break timer display function
Press BREAK TIMER.
Note
• Break Timer does not function while the projector is operating the “Auto Sync”, “FREEZE”
or “AV MUTE” functions.
Switching the Eco+Quiet
Mode
Press ECO+QUIET to switch the
Eco+Quiet mode between on and off.
• When the Eco+Quiet Mode is set to “ON”, the
sound of the cooling fan will turn down, the
power consumption will decrease, and the lamp
life will extend.
Note
• Refer to “Lamp Setting” on page 42 for details of the Eco+Quiet mode.
32
Auto Sync
(Auto Sync Adjustment)
Displaying an Enlarged
Portion of an Image
Auto Sync function works when detecting input signal after the projector turns
on.
Press AUTO SYNC to manually adjust
with Auto Sync function.
Graphs, tables and other portions of
projected images can be enlarged. This
is helpful when providing more detailed
explanations.
1
Note
Press
control.
MAGNIFY on the remote
• Enlarges the image.
• Pressing
or
MAGNIFY enlarges
or reduces the projected image.
• When the optimum image cannot be achieved
with Auto Sync adjustment, use the help menu
for manual adjustments. (See page 48.)
Note
Press
.
´1 ´2 ´3 ´4
Freezing a Moving Image
Press
1
Press FREEZE.
2
Press FREEZE again to return to
the moving image from the currently connected device.
.
• You can change the location of the enlarged image using P, R, O and Q.
• The projected image is frozen.
2
Press RETURN on the remote control to cancel the operation.
• The magnification then returns to ×1.
Note
Selecting the Picture Mode
You can select the appropriate picture
mode for the projected image, such as
movie or video game.
Press PICTURE MODE.
• When pressing PICTURE MODE, the picture
mode changes in the following order:
STANDARD
PRESENTATION
MOVIE
GAME
sRGB
*
• The selectable magnifications differ depending on the input signal.
• In the following cases, the image will
return to the normal size (×1).
- When switching the INPUT mode.
- When RETURN has been pressed.
- When the input signal is changed.
- When the input signal resolution and
refresh rate (ver tical frequency)
change.
- When the Resize mode is changed.
- When the Picture mode is changed.
- When the Progressive mode is changed.
Note
• See page 40 for details on the picture mode.
* “sRGB” is displayed only when RGB signal is
input.
33
Operating with the Remote Control (Continued)
Using the Remote Control as the Wireless Computer Mouse
When connecting the projector and the computer with a USB cable, you can use
the remote control as the computer mouse.
Connecting with a USB cable
Computer
To USB terminal
To USB terminal
USB cable
(commercially available)
The mouse pointer can be operated in the following way after it
is connected.
PAGE UP/
PAGE DOWN buttons
MOUSE/Adjustment
buttons ('/"/\/|)
■ When moving the cursor
Press MOUSE/Adjustment buttons (P/R/O/Q).
■ When left-clicking
Press L-CLICK.
■ When right-clicking
Press R-CLICK.
R-CLICK button
■ When your computer supports only a
one-click mouse (such as Macintosh)
Press L-CLICK or R-CLICK.
L-CLICK and R-CLICK have common function.
L-CLICK button
■ When using [Page Up] or [Page Down]
Same as the [Page Up] and [Page Down] keys on a computer keyboard.
Press PAGE UP or PAGE DOWN.
Note
• This function only works with the Microsoft® Windows® OS and Mac OS®. However, this function
does not work with the following operation systems that do not support USB.
• Versions earlier than Windows® 95
• Versions earlier than Windows® NT4.0
• Versions earlier than Mac OS® 8.5
• You cannot use this function when displaying the menu screen.
• Confirm that the computer recognizes the USB connection.
34
Menu Items
The following shows the items that can be set in the projector.
Main menu
“Picture” menu
Picture
Page 40
PAGE 1
Picture
SCR - ADJ
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Blue
PRJ - ADJ
Sub menu
Standard
Presentation
Movie
Game
sRGB*1
Picture Mode
Page 40
Help
Standard
0
0
0
0
0
0
0
Contrast
-30
+30
Bright
-30
+30
Color
-30
+30 *2
Tint
-30
+30 *2
Sharp
-30
+30 *2
Red
-30
+30
Blue
-30
+30
Page 41
SEL./ADJ.
ENTER
END
PAGE 2
Picture
CLR Temp
SCR - ADJ
PRJ - ADJ
Picture Mode
Help
Standard
BrilliantColor™
1
0
2 *3
Page 41
0
1
CLR Temp
BrilliantColor TM
C.M.S. Setting
C.M.S.
Progressive
DNR
Lamp Setting
Reset
-1
Page 41
C.M.S. Setting [On/Off]
On
Page 41
3D Progressive
Off
Bright
C.M.S.
Page 41
Progressive
2D Progressive
3D Progressive
Film Mode
*2
Page 42
SEL./ADJ.
ENTER
END
DNR
Off
Level 1
Level 2
Page 42
Bright
Eco + Quiet
Lamp Setting
Page 42
“C.M.S.”
Reset
C. M. S.
C. M. S. - Hue
C. M. S. - Saturation
C. M. S. - Value
Reset
C.M.S.-Hue
R
Y
G
C
B
M
Reset
SEL./ADJ.
Return
0
0
0
0
0
0
R
-30
+30
Page 41
Y
-30
+30
C.M.S.-Saturation
G
-30
+30
Page 41
C
-30
+30
B
-30
+30
M
-30
+30
C.M.S.-Value
Page 41
Reset
Reset
ENTER
END
*1 Items when inputting RGB signal through
COMPUTER or DVI (EIP-2600 only).
*2 Items when inputting component signal through
COMPUTER or DVI (EIP-2600 only), or when
selecting S-VIDEO or VIDEO.
*3 On model EIP-250, this item is “Bright Boost”.
35
Menu Items (Continued)
“Screen adjustment (SCR-ADJ)” menu
Picture
SCR - ADJ
Resize
Image Shift
Keystone
PRJ - ADJ
Help
Main menu
SCR - ADJ
Normal
Page 43
0
0
Normal
Full
Dot By Dot
Area Zoom
V-Stretch
Border
Stretch
Page 43
Image Shift
-96 +96 *3
-75 +75 *4
On
CC1
Logo
On
Front
English
OSD Display
Closed Caption
Background
Setup Guide
PRJ Mode
Language
Sub menu
Resize
Page 43
COMPUTER/
DTV
Keystone
-80
-40
Normal
Area Zoom
V-Stretch
Border
Stretch
+80 *3
+40 *4
Page 43
OSD Display [On/Off]
Page 43
SEL./ADJ.
ENTER
END
Off
CC1
CC2
Closed Caption
Page 44
*3 Adjustment range for EIP-2600.
*4 Adjustment range for EIP-250.
Logo
Blue
None
Background
Page 44
Setup Guide [On/Off]
Page 44
Front
Ceiling + Front
Rear
Ceiling + Rear
PRJ Mode
Page 44
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
Language
Page 44
polski
Magyar
Türkçe
“Projector adjustment (PRJ-ADJ)” menu
Picture
SCR - ADJ
Auto Sync
Auto Power Off
Auto Restart
STANDBY Mode
System Sound
Speaker
Audio Input
RS-232C
Fan Mode
System Lock
Lamp Timer(Life)
SEL./ADJ.
PRJ - ADJ
0 h
ENTER
Help
On
On
On
Standard
On
On
Audio 1
9600bps
Normal
Disable
0 min 100%
END
*5 This item is available for EIP-2600 only.
Main menu
PRJ - ADJ
Page 45
Sub menu
Auto Sync [On/Off]
Page 45
Auto Power Off [On/Off]
Page 45
Auto Restart [On/Off]
Page 45
STANDBY Mode
System Sound [On/Off]
Page 45
Speaker [On/Off]
Page 45
Audio Input
Page 46
RS-232C
Page 46
Fan Mode
Page 46
System Lock
[Enable/Disable]
Page 46
Lamp Timer(Life)
Page 47
36
Standard
Eco
Page 45
*5
Audio 1
Audio 2
9600bps
115200bps
Normal
High
VIDEO/
S-VIDEO
The items you can set with the “Help”
menu
“Help” menu
Picture
SCR - ADJ
PRJ - ADJ
Help
“Help” menu n Page 48
There is no picture or audio
Vertical stripes or flickering image appear
Data image is not centered
Color is faded or poor
Picture is dark
The image is distorted
Reset all adjustments to default settings
SEL
SEL.
ENTER
END
• Vertical stripes or flickering image appear
Auto Sync
Clock
Phase
• Data image is not centered
Auto Sync
H-Pos
V-Pos
• Color is faded or poor
COMPUTER/COMPONENT or DVI (EIP-2600
only) input
Signal type: Auto/RGB/Component
S-VIDEO or VIDEO input
Video System: Auto/PAL/SECAM/
NTSC3.58/NTSC4.43/
PAL-M/PAL-N/PAL-60
DVI (Digital) input (EIP-2600 only)
Dynamic range: Auto/Standard/Enhanced
* The selectable items vary depending on the input signal and the selected input mode.
37
Using the Menu Screen
ENTER button
Adjustment buttons (P/R/O/Q)
MENU/HELP button
ENTER button
Adjustment buttons
(P/R/O/Q)
RETURN button
• Press RETURN to return
to the previous screen
when the menu is
displayed.
MENU/HELP button
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.
1
Press MENU/HELP.
2
Press Q or O and select “Picture”
to adjust.
• The “Picture” menu screen for the selected input mode is displayed.
Example: “Picture” screen menu for
COMPUTER (RGB) input
(EIP-2600)
Menu item
Picture
SCR - ADJ
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
BrilliantColor TM
C.M.S. Setting
C.M.S.
DNR
Lamp Setting
Reset
SEL./ADJ.
38
PRJ - ADJ
Help
Standard
0
0
0
0
0
1
On
Off
Bright
ENTER
END
3
Press P or R and select “Bright”
to adjust.
• The selected item is highlighted.
Picture
SCR - ADJ
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
BrilliantColor TM
C.M.S. Setting
C.M.S.
DNR
Lamp Setting
Reset
SEL./ADJ.
PRJ - ADJ
Help
Standard
0
0
0
0
0
1
On
Off
Bright
Single ADJ
END
Items to be adjusted
Picture
To adjust the projected
image while watching it
SCR - ADJ
Resize
Image Shift
Keystone
PRJ - ADJ
Help
Border
0
0
Press ENTER.
• The selected item (e.g. “Bright”) is displayed by itself at the bottom of the
screen.
• When pressing P or R, the following item
(“Red” after “Bright”) will be displayed.
Press ENTER.
The item displayed by itself
Picture
Bright
SEL./ADJ.
0
Rtn. Menu
END
Note
• Press ENTER again to return to the previous screen.
4
Press O or Q to adjust the item
selected.
• The adjustment is stored.
5
Press MENU/HELP.
• The menu screen will disappear.
Picture
SCR - ADJ
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
BrilliantColor TM
C.M.S. Setting
C.M.S.
DNR
Lamp Setting
Reset
SEL./ADJ.
PRJ - ADJ
Help
Standard
0
15
0
0
0
1
On
Off
Bright
Single ADJ
END
Note
• Menu buttons do not function while the projector is operating the “Auto Sync”, “Break Timer”,
“FREEZE”, or “AV MUTE” functions.
39
Picture Adjustment (“Picture” Menu)
Menu operation n Page 38
Q PAGE1
Q PAGE2
Picture
1
2
SCR - ADJ
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Blue
SEL./ADJ.
PRJ - ADJ
Help
Picture
Standard
0
0
0
0
0
0
0
ENTER
SCR - ADJ
PRJ - ADJ
Picture Mode
3
2
4
5
6
7
END
Help
Standard
CLR Temp
BrilliantColor TM
C.M.S. Setting
C.M.S.
Progressive
DNR
Lamp Setting
Reset
SEL./ADJ.
0
1
On
3D Progressive
Off
Bright
ENTER
END
1 Selecting the Picture Mode
Selectable
items
Standard
The default settings of each item when selecting Picture Mode
Description
For standard image
CLR Temp
BrilliantColorTM (EIP-2600)
Bright Boost (EIP-250)
Lamp Setting
0
1
Bright
Presentation Brightens portions of image for
more enhanced presentations.
0
2
Bright
Movie
Gives natural tint to the
projected image.
–1
0
Eco + Quiet
Game
Gives sharpness to the
projected image.
0
1
Bright
*sRGB
For high fidelity reproduction of
images from a computer.
–
–
Bright
• “sRGB” is displayed only when RGB signal is input.
• You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are
retained in memory.
Note
• You can also press PICTURE MODE on the remote control to select the picture mode. (See page 33.)
• *sRGB is an international standard of color reproduction regulated by the IEC (International
Electrotechnical Commission). As the fixed color area has been decided by the IEC, the images are
displayed in a natural tint based on an original image, when “sRGB” is selected.
For additional information about the sRGB function, visit “http://www.srgb.com/”.
You cannot set the items, “Red”, “Blue”, “CLR Temp”, “Bright Boost”, when “sRGB” is selected.
Info
• When “sRGB” is selected, the projected image may become dark, but this does not indicate a
malfunction.
40
Menu operation n Page 38
2 Adjusting the Image
Adjustment
items
Contrast
O button
Q button
For less
contrast.
For less
Bright
brightness.
For less color
Color*1
intensity.
1
For making skin
Tint*
tones purplish.
For less
Sharp*1
sharpness.
Red*2
For weaker red.
Blue*2
For weaker blue.
BrilliantColor™*2 *3 For making the
(EIP-2600)
effect weaker.
Bright Boost*2
(EIP-250)
For more
contrast.
For more
brightness.
For more color
intensity.
For making skin
tones greenish.
For more
sharpness.
For stronger red.
For stronger blue.
For making the
effect stronger.
*1 Not displayed in the RGB input mode.
*2 Not adjustable/selectable when selecting “sRGB”.
*3 BrilliantColor™ uses Texas Instruments’
BrilliantColor™ technology. As the BrilliantColor™
level is increased, the image becomes brighter
while the color reproduction is kept at a high level.
4 Adjusting the Colors
This function adjusts each of the six main colors
that comprise the color wheel, altering their
“Hue”, “Saturation”, or “Value”.
Selectable items
Description
C.M.S.-Hue
Sets the hue of the main colors.
C.M.S.-Saturation
Sets the saturation of the main
colors
C.M.S.-Value
Sets the brightness of the main
colors.
Reset
The adjustments of “Hue”,
“Saturation” and “Value” of all
colors are reset to the default
setting.
Adjusting “Hue”, “Saturation”, or “Value”.
1 Select “On” for “C.M.S. Setting” in the “Picture”
menu and then press ENTER.
2 Select “C.M.S.” in the “Picture” menu and then
press ENTER.
3 Press P or R to select either “Hue”, “Saturation”, or
“Value” and then press ENTER.
4 Select the color to be adjusted with P or R and
adjust it with O or Q.
Example of adjusting the “Hue”
Note
Main colors
• “Red”, “Blue”, “BrilliantColorTM” (EIP-2600),
“Bright Boost” (EIP-250) and “CLR Temp” cannot be set when “sRGB” is selected.
• To reset all adjustment items, select “Reset”
and press ENTER.
3 Adjusting the Color
Temperature
Selectable
items
–1
Description
For lower color temperature for
warmer, reddish incandescent-like
images.
P
0
R
1
For higher color temperature for
cooler, bluish, fluorescent-like images.
O button
Q button
R (Red)
Closer to magenta Closer to yellow
Y (Yellow)
Closer to red
Closer to green
G (Green)
Closer to yellow
Closer to cyan
C (Cyan)
Closer to green
Closer to blue
B (Blue)
Closer to cyan
Closer to magenta
M (Magenta) Closer to blue
Closer to red
• When “Saturation” is selected, the selected
color becomes
O: lighter. Q: thicker.
• When “Value” is selected, the selected color
becomes
O: darker. Q: brighter.
• To reset the adjustment values of each color
to the default settings, select “Reset” and press
ENTER.
Note
• Values on “CLR Temp” are only for general
standard purposes.
41
Picture Adjustment (“Picture” Menu)
(Continued)
Menu operation n Page 38
5 Progressive
Selectable
items
Description
Useful to display fast-moving images
2D
Progressive such as sports.
Useful to display relatively slow3D
Progressive moving images such as drama and
documentary more clearly.
Film Mode
Reproduces the image of film source*
clearly. Displays the optimized image of
film transformed with three-two pull down
(NTSC and PAL60Hz) or two-two pull
down (PAL50Hz and SECAM) enhancement to progressive mode images.
* The film source is a digital video recording with the
original encoded as is at 24 frames/second. The
projector can convert this film source to progressive video at 60 frames/second with NTSC and
PAL60Hz or at 50 frames/second with PAL50Hz
and SECAM to play back a high-definition image.
Note
• In NTSC or PAL60Hz, even if the 3D Progressive mode has been set, the three-two pull
down enhancement will be enabled automatically when the film source has been entered.
• When the image is blurred or noisy, switch to
the optimal mode.
6 Reducing Image Noise (DNR)
Video digital noise reduction (DNR) provides high
quality images with minimal dot crawl and cross
color noise.
Selectable
items
Description
Off
The DNR function is not activated.
Level 1
Sets the DNR level for viewing a
clearer picture.
Level 2
Note
Set “DNR” to “Off” in the following cases:
• When the image is blurry.
• When the contours and colors of moving images drag.
• When TV broadcasts with weak signals are
projected.
7 Lamp Setting
Selectable
items
Brightness and Power consumption
Eco + Quiet EIP-2600
EIP-250
Bright
Approx. 70%
Approx. 80%
100%
Info
• This function is available for 480I and 576I
signals using COMPUTER/COMPONENT or
DVI (EIP-2600 only) input.
• This function is available for all signals with
S-VIDEO and VIDEO input.
42
Note
• In the Eco + Quiet mode, the fan sound and
power consumption are lower than those in
the Bright mode. (Projection brightness decreases as shown in the chart.)
Adjusting the Projected Image
(“SCR - ADJ” Menu)
Menu operation n Page 38
Picture
1
2
3
Resize
Image Shift
Keystone
4
5
6
7
8
9
OSD Display
Closed Caption
Background
Setup Guide
PRJ Mode
Language
SCR - ADJ
SEL./ADJ.
1 Setting the Resize Mode
Note
• For details of the Resize mode, see pages
30 and 31.
• You can also press RESIZE on the remote control to set the resize mode. (See page 30.)
2 Adjusting the Image
Position
PRJ - ADJ
Help
Normal
0
0
On
CC1
Logo
On
Front
English
ENTER
END
3 Keystone Correction
When the image is projected either from the top
or from the bottom towards the screen at an angle,
the image becomes distorted trapezoidally. The
function for correcting trapezoidal distortion is
called Keystone Correction.
Select “Keystone” on the “SCR-ADJ”
menu and adjust with the slide bar.
See page 28 for details of Keystone Correction.
Q button
O button
You can move the projected image vertically.
Note
O button
Q button
Note
• This function only works in some RESIZE
modes. (See pages 30 and 31.)
• The Keystone Correction can be adjusted up
to an angle of approximately ±40 (EIP-2600)/
±20 (EIP-250) degrees (when “Resize” is set
to “Normal”).
• You can also press KEYSTONE on the remote
control or on the projector to adjust Keystone
Correction.
4 Setting the On-screen
Display
Selectable
items
Description
On
All on-screen displays are displayed.
Off
INPUT/VOLUME/AV MUTE/FREEZE/
AUTO SYNC/RESIZE/PICTURE MODE/
ECO+QUIET/MAGNIFY/ “An invalid
button has been pressed.” are not
displayed.
43
Adjusting the Projected Image
(“SCR - ADJ” Menu) (Continued)
Menu operation n Page 38
5 Closed Caption
7 Selecting the Setup Guide
Selectable items
On
Info
• This function is available for NTSC3.58 and 480I
signals.
• This function does not work when the resize
mode is set to “Border”.
• This function is available in the following cases
only:
Keystone Correction
Resize mode
Normal
-40 – +40
Area Zoom
V-Stretch
-12 – +12
Stretch
• “Closed Caption” is a system which allows
conversations, narration, and sound effects in
TV programs (Limited regions) and home
videos to be viewed as captions on the screen.
• Not all programs and videos will offer closed
captioning. Please look for the
symbol to
ensure that captions will be shown.
• Two channels are available: CC1 and CC2.
• The Closed Caption letters of this projector
are displayed in black and white.
Description
Selectable items
Off
—
Closed Caption mode for CH1 data
CC1
Closed Caption mode for CH2 data
CC2
Off
Description
Displaying the Setup Guide
when turning the projector on.
Not displaying the Setup Guide.
8 Reversing/Inverting
Projected Images
Selectable items
Description
Front
Normal image (Projected from
the front of the screen)
Ceiling + Front
Inverted image (Projected
from the front of the screen
with an inverted projector)
Rear
Reversed image (Projected
from the rear of the screen or
with a mirror)
Ceiling + Rear
Reversed and inverted image
(Projected with a mirror)
See page 19 for details of Projection (PRJ) Mode.
9 Selecting the On-screen
Display Language
The projector can switch the on-screen display
language among 17 languages.
Note
• Closed Caption may malfunction (white blocks,
strange characters, etc.) if signal conditions are
poor or if there are problems at the broadcast
source. This does not necessarily indicate a
problem with the projector.
• If any button is pressed to call up the on-screen
display while viewing a Closed Caption broadcast,
the closed captions will disappear.
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
polski
Magyar
6 Selecting the Background
Image
Selectable items
Logo
Blue
None
44
Description
EIKI logo screen
Blue screen
—
Türkçe
Adjusting the Projector Function (“PRJ - ADJ” Menu)
Menu operation n Page 38
Picture
1
2
3
4
5
6
7
8
9
0
SCR - ADJ
Auto Sync
Auto Power Off
Auto Restart
STANDBY Mode
System Sound
Speaker
Audio Input
RS-232C
Fan Mode
System Lock
Lamp Timer(Life)
SEL./ADJ.
PRJ - ADJ
0 h
Help
On
On
On
Standard
On
On
Audio 1
9600bps
Normal
Disable
0 min 100%
ENTER
Description
Auto Sync adjustment will occur when
the projector is turned on or when the
input signals are switched, when
connected to a computer.
On
Auto Sync adjustment is not automatically performed.
Off
Selectable
items
If the power cord is unplugged from the
outlet or the breaker switch is turned off
when the projector is on, then the
projector automatically turns on when
the power cord is plugged into the AC
outlet or the breaker switch is turned on.
Off
The projector does not turn on
automatically when the power cord is
plugged into the AC outlet or the
breaker switch is turned on.
4 STANDBY Mode
When set to “Eco”, power consumption is
reduced in standby mode.
Selectable
items
2 Auto Power Off Function
Selectable
items
Description
When no input signal is detected for
more than 15 minutes, the projector will
automatically enter standby mode.
On
The Auto Power Off function will be
disabled.
Off
Note
Description
Eco
The monitor output and RS-232C
functions are switched off in standby
mode.
Standard
The monitor output and RS-232C
functions are activated even if the
projector is in standby mode.
Note
• Auto Sync adjustment is also performed by
pressing AUTO SYNC on the remote control.
• The Auto Sync adjustment may take some time
to complete, depending on the image of the
computer connected to the projector.
• When the optimum image cannot be achieved
with Auto Sync adjustment, use manual
adjustments. (See page 48.)
Description
On
END
1 Auto Sync (Auto Sync
Adjustment)
Selectable
items
3 Auto Restart Function
5 Setting the Confirmation
Sound (System Sound)
Selectable
items
Description
On
A confirmation sound is made when
the projector turns on/off.
Off
No confirmation sound is made.
6 Speaker Setting
Selectable
items
Description
On
The audio signal is output from the
internal speaker.
Off
The audio signal is not output from the
internal speaker.
• When the Auto Power Off function is set to
“On”, 5 minutes before the projector enters
standby mode, the message “Enter STANDBY
mode in X min.” will appear on the screen to
indicate the remaining minutes.
45
Adjusting the Projector Function (“PRJ - ADJ” Menu)
(Continued)
Menu operation n Page 38
a
Setting/Changing
the keycode
7 Audio
Input
(EIP-2600 only)
6
Monitor
Output
This function allows you to select an appropriate combination of audio input terminals for each
input mode.
Selectable
items
Description
Audio 1
The AUDIO 1 input terminal is used as
an audio input terminal.
Audio 2
The AUDIO 2 input terminal is used as
an audio input terminal.
1
Select “System Lock”, then press
ENTER or Q.
2
Select “Next”, then press ENTER.
3
Press the 4 buttons on the remote
control or on the projector to enter
the preset keycode in “Old Code”.
8 Selecting the Transmission
Speed (RS-232C)
• When setting the keycode for the first time,
press R on the projector for four times.
PRJ - ADJ
Make sure that both the projector and computer
are set for the same baud rate.
Selectable
items
9600bps
Setting the System Lock
Transmission speed is slow.
P
R
Note
• If you input a wrong keycode, the cursor
returns to the first point of the “Old Code”.
• The preset keycode is 4 R buttons on
the projector. When you press the R button four times, the keycord input screen
disappears.
9 Fan Mode Setting
This function changes the fan rotation speed.
Description
Normal
Suitable for normal environments.
High
Select this when using the projector at
altitudes of approximately 1,500
meters (4,900 feet) or more.
When “Fan Mode” is set to “High”, the fan rotation
speeds up, and the fan noise becomes louder.
0 System Lock Function
This function prevents unauthorized use of the
projector. Once this function is activated, users
must enter the correct keycode each time the
projector is turned on. We suggest you record
the keycode in a safe place where only authorized users have access.
4
Press the 4 buttons on the remote
control or on the projector to enter
the new keycode in “New Code”.
Note
• You cannot use the following buttons for
keycode: STANDBY/ON, ON, STANDBY,
ENTER, L-CLICK, R-CLICK/RETURN
and MENU/HELP
• System lock function recognizes each
button on the remote control or on the
projector as an individual button, even if
they share the same button name. If you
used the buttons on the projector in setting your keycode, the keycode cannot be
canceled with the remote control.
Info
• If you lose or forget your keycode, contact
your nearest EIKI Authorized Dealer or Service
Center. Even if the product warranty is valid,
the keycode reset will incur a charge.
46
– – – –
– – – –
– – – –
Old Code
New Code
Reconfirm
Description
115200bps Transmission speed is rapid.
Selectable
items
• The screen for entering the keycode
appears.
PRJ - ADJ
Setting the System Lock
Old Code
New Code
Reconfirm
****
– – – –
– – – –
5
Enter the same keycode in “Reconfirm”.
Keylock Function
Locking the Operation
Buttons on the Projector
Note
To cancel the keycode that you have already
set
• Press R on the projector for four times in steps
4 and 5 above.
When the System Lock is set
• When System Lock is set, the keycode input
screen appears after the power is turned on.
When it appears, enter the right keycode to
start projection.
Input screen for keycode
a Locking the Operation Buttons
Hold down ENTER on the projector for about 5
seconds while the projector is being turned on.
On-screen display
• The keylock function does not affect the operation with the remote control buttons.
• You cannot use the keylock function while the
projector is warming up.
– – – –
System Lock
Use this function to lock the operation buttons
on the projector.
a Taking the Keylock off
Checking the Lamp Life
Status
Hold down ENTER on the projector for about 5
seconds.
On-screen display
You can confirm the cumulative lamp usage time
and the remaining lamp life (percentage).
Lamp usage condition
“Life”
Remaining lamp life
100%
5%
Operated exclusively
with Lamp Setting set to
“Eco +Quiet”
Approx.
4,000
hours
Approx.
200 hours
Operated exclusively
with Lamp Setting set to
“Bright”
Approx.
2,000
hours
Approx.
100 hours
Note
• When the projector is in standby mode, you can
release the keylock by holding down ENTER
and STANDBY/ON on the projector simultaneously for about 5 seconds.
Info
• Keylock cannot be set while the projector is:
displaying the “Setup Guide” or “Menu”
screens, in standby mode, warming up, changing input signals, operating “Auto Sync” function, in “FREEZE” mode or on the “System
Lock” screen during warming up.
• It is recommended that the lamp be changed
when the remaining lamp life becomes 5%.
• The lamp life may vary depending on the usage condition.
47
Troubleshooting with the “Help” Menu
This function advises you to solve the problems during usage.
Utilizing the “Help” Menu
Functions
ENTER button
Adjustment buttons
(P/R/O/Q)
Example: When image flickering appears
Operation to solve image flickering when projecting the computer RGB signal.
1
Press MENU/HELP.
2
Press O or Q to select “Help”, then
press ENTER.
3
Press P or R to select “Vertical
stripes or flickering image appears” on Help menu, then press
ENTER.
Picture
SCR - ADJ
PRJ - ADJ
Help
Vertical stripes or flickering image appear
There is no picture or audio
Vertical stripes or flickering image appear
Data image is not centered
Color is faded or poor
Picture is dark
The image is distorted
ENTER
END
Help
Vertical stripes or flickering image appear
Initiate “Auto Sync” Adjustments.
If there is no change after performing "Auto Sync"
adjustments, adjust the following items.
Adjust vertical noise
Adjust horizontal noise
Reset the 2 items above
Return
Signal Info
1024768
H
48.3 kHz / V 59.9 Hz
48
ENTER
Select “Initiate “Auto Sync” Adjustments”, then press ENTER.
5
If the image is not improved, select “Adjust horizontal noise”,
then press ENTER.
6
Press O or Q to adjust.
Help
0
Rtn. Menu
END
Note
Press ENTER.
SEL.
4
Phase
SEL./ADJ.
Reset all adjustments to default settings
SEL.
MENU/HELP
button
END
• You can adjust the items with check marks (✔).
• The items in the “Help” menu change, depending on the input signal or setting that you
have selected.
• If the problem is not solved, refer to
“Troubleshooting” (see pages 63 and 64).
• When selecting “sRGB” in “Picture Mode”, the
item “Color is faded or poor” is not displayed.
This means you cannot change input signal
types.
Maintenance
Cleaning the projector
■ Ensure that you have unplugged the power
cord before cleaning the projector.
■ The cabinet as well as the operation panel is
made of plastic. Avoid using benzene or
thinner, as these can damage the finish on the
cabinet.
■ Do not use volatile agents such as insecticides
on the projector.
Do not attach rubber or plastic items to the
projector for long periods.
The effects of some of the agents in the plastic
may cause damage to the quality or finish of the
projector.
■ Wipe off dirt gently with a soft flannel cloth.
■ When the dirt is hard to remove, soak a cloth in
a mild detergent diluted with water, wring the
cloth well and then wipe the projector.
Strong cleaning detergents may discolor, warp
or damage the coating on the projector. Make
sure to test on a small, inconspicuous area on
the projector before use.
Cleaning the lens
■ Use a commercially available blower or lens
cleaning paper (for glasses and camera lenses)
for cleaning the lens. Do not use any liquid type
cleaning agents, as they may wear off the
coating film on the surface of the lens.
■ As the surface of the lens can easily get
damaged, be careful not to scrape or hit the
lens.
Cleaning the exhaust and intake vents
■ Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
nt
rge
ete
dd
Mil
Mild detergent diluted
with water
Info
Wax
Thinner
• If you want to clean the air vents during projector operation, ensure you press STANDBY/ON
on the projector or STANDBY on the remote
control and put the projector into standby
mode. After the cooling fan has stopped, clean
the vents.
49
Maintenance Indicators
■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the
projector indicate problems inside the projector.
■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate
red, and the projector will enter standby mode. After the projector has entered standby mode,
follow the procedures given below.
Top View
Temperature warning
indicator
Lamp indicator
Power indicator
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,
“
” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp
will turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projector will enter standby mode. After “
” appears, ensure you perform the measures described on
page 51.
About the lamp indicator
■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be
displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will
automatically turn off and then the projector will automatically enter standby mode. At this time, the
lamp indicator will illuminate in red.
■ If you try to turn on the projector a fourth time without replacing the lamp, the projector will
not turn on.
Indicators on the Projector
Power indicator
Lamp indicator
Temperature warning
indicator
50
Green on
Red on
Green blinks
Red blinks
Green on
Green blinks
Red on
Off
Red on
Normal (Standby)
Normal (Power on)
Abnormal (See page 51.)
Normal (Cooling)
Normal
The lamp is warming up.
The lamp is shut down abnormally or requires to be
changed. (See page 51.)
Normal
The internal temperature is abnormally high. (See page 51.)
Maintenance indicator
Temperature
warning
indicator
Lamp
indicator
Power
indicator
Normal
Abnormal
Off
Red on
(Standby)
Red on
Problem
The internal
temperature is
abnormally
high.
Cause
• Blocked air intake
• Relocate the projector to
an area with proper
ventilation. (See page 8.)
• Cooling fan
breakdown
• Internal circuit
failure
• Clogged air intake
• Take the projector to your
nearest EIKI Authorized
Dealer or Service Center
for repair.
The lamp does
not illuminate.
• The lamp is shut
down abnormally.
• Disconnect the power cord
from the AC outlet, and
then connect it again.
Time to change
the lamp.
• Remaining lamp life
becomes 5% or
less.
• Carefully replace the lamp.
(See page 52.)
• Take the projector to your
nearest EIKI Authorized
Dealer or Service Center
for repair.
• Please exercise care when
replacing the lamp.
• Securely install the cover.
Green on
(Green
blinks
when the
lamp is
warming
up or
turning
off.)
Red on
(Standby)
The lamp does
not illuminate.
• Burnt-out lamp
• Lamp circuit failure
Red on/
Green on
Green
blinks
The power
indicator blinks
in green when
the projector is
on.
• The lamp unit cover
is open.
Red
blinks
(Cooling)
Possible Solution
• If the power indicator blinks
in green even when the
lamp unit cover are
securely installed, contact
your nearest EIKI
Authorized Dealer or
Service Center for advice.
Info
• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the
possible solutions above and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using
the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet,
replace the power cord in the AC outlet and then turn the power on again.
• The cooling fan keeps the internal temperature of the projector constant and this function is controlled automatically. The sound of the cooling fan may change during operation because the fan
speed may change and this is not a malfunction.
51
Regarding the Lamp
Lamp
■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes
5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life
(percentage) can be checked with the on-screen display. (See page 47.)
■ Purchase a replacement lamp of type AH-62101 from your place of purchase, nearest EIKI Authorized
Dealer or Service Center.
Hg LAMP CONTAINS MERCURY For State Lamp Disposal
Information
U.S.A. ONLY
www.lamprecycle.org or 1-800-242-3454
Caution Concerning the Lamp
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest EIKI Authorized Dealer or
Service Center to assure safe operation.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case
of exposure to the gas, consult a doctor as soon as possible.
Replacing the Lamp
Caution
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may
cause burns or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully
cool before removing the lamp unit.
■ Carefully change the lamp by following the instructions described in this section. * If you wish,
you may have the lamp replaced at your nearest EIKI Authorized Dealer or Service Center.
* If the new lamp does not light after replacement, take your projector to the nearest EIKI Authorized
Dealer or Service Center for repair.
52
Removing and Installing
the Lamp Unit
Warning!
• Do not remove the lamp unit from the projector right after use. The lamp and parts around
the lamp will be very hot and may cause burns
or injury.
Info
Lamp unit
AH-62101
Optional
accessory
STANDBY/ON button
• Do not touch the glass surface of the lamp
unit or the inside of the projector.
• To avoid injury to yourself and damage to the
lamp, make sure you carefully follow the steps
below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
1
AC socket
Press STANDBY/ON on the projector or STANDBY on the remote
control to put the projector into
standby mode.
User service screw
(for lamp unit cover)
• Wait until the cooling fan stops.
2
3
Disconnect the power cord.
• Unplug the power cord from the AC
socket.
• Leave the lamp until it has fully cooled
down (about 1 hour).
1
2
Remove the lamp unit cover.
• Turn the projector over. Loosen the user
service screw (1) that secures the lamp
unit cover. Remove the lamp unit cover
(2).
53
Regarding the Lamp (Continued)
4
Remove the lamp unit.
5
Insert the new lamp unit.
6
• Loosen the securing screws from the
lamp unit. Hold the lamp unit and pull it
in the direction of the arrow. At this time,
keep the lamp unit horizontal and do not
tilt it.
• Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
Securing screws
Replace the lamp unit cover.
• Align the tab on the lamp unit cover
(1) and place it while pressing the tab
(2) to close it. Then tighten the user service screw (3) to secure the lamp unit
cover.
Info
• If the lamp unit and lamp unit cover are
not correctly installed, the power will not
turn on, even if the power cord is connected to the projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this may
cause the lamp to become damaged or explode.
1
2
54
AC socket
Connect the power cord.
• Plug the power cord into the AC socket
of the projector.
Reset the lamp timer.
• While simultaneously holding down
MENU/HELP, ENTER and R on the projector, press STANDBY/ON on the projector.
• “LAMP 0000H” is displayed, indicating
that the lamp timer is reset.
STANDBY/ON
button
ENTER button
R button
MENU/HELP
button
Connecting Pin Assignments
COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals : mini Dsub 15 pin female connector
11
1
6
15
5
10
COMPUTER Input/Output
Pin No.
Signal
1. Video input (red)
2. Video input (green/sync on green)
3. Video input (blue)
4. Not connected
5. Not connected
6. Earth (red)
7. Earth (green/sync on green)
8. Earth (blue)
9. Not connected
10. GND
11. Not connected
12. Bi-directional data
13. Horizontal sync signal: TTL level
14. Vertical sync signal: TTL level
15. Data clock
COMPONENT Input/Output
Pin No.
Signal
1. PR (CR)
2. Y
3. PB (CB)
4. Not connected
5. Not connected
6. Earth (PR)
7. Earth (Y)
8. Earth (PB)
9. Not connected
10. Not connected
11. Not connected
12. Not connected
13. Not connected
14. Not connected
15. Not connected
DVI-I Terminal : 29 pin connector (EIP-2600 only)
23
24
18
17
C3
C5
C4
C2
C1
87
16
21
9
• DVI Analog RGB Input
Pin No.
Signal
Pin No.
Signal
1. Not connected
16. Hot plug detection
2. Not connected
17. Not connected
3. Not connected
18. Not connected
4. Not connected
19. Not connected
5. Not connected
20. Not connected
6. DDC clock
21. Not connected
7. DDC data
22. Not connected
8. Vertical sync
23. Not connected
9. Not connected
24. Not connected
10. Not connected
C1. Analog input Red
11. Not connected
C2. Analog input Green
(Sync On Green)
12. Not connected
C3. Analog input Blue
13. Not connected
C4. Horizontal sync
(Composite Sync)
14. +5V power
C5. Ground
15. Ground
• DVI Digital Input
Pin No.
Signal
1. T.M.D.S data 2–
2. T.M.D.S data 2+
3. T.M.D.S data 2 shield
4. Not connected
5. Not connected
6. DDC clock
7. DDC data
8. Not connected
9. T.M.D.S data 1–
10. T.M.D.S data 1+
11. T.M.D.S data 1 shield
12. Not connected
13. Not connected
14. +5V power
15. Ground
Pin No.
16.
17.
18.
19.
20.
21.
22.
23.
24.
C1.
C2.
C3.
C4.
C5.
Signal
Hot plug detection
T.M.D.S data 0–
T.M.D.S data 0+
T.M.D.S data 0 shield
Not connected
Not connected
T.M.D.S clock shield
T.M.D.S clock+
T.M.D.S clock–
Not connected
Not connected
Not connected
Not connected
Ground
• DVI Analog Component Input
Pin No.
Signal
Pin No.
Signal
1. Not connected
16. Not connected
2. Not connected
17. Not connected
3. Not connected
18. Not connected
4. Not connected
19. Not connected
5. Not connected
20. Not connected
6. Not connected
21. Not connected
7. Not connected
22. Not connected
8. Not connected
23. Not connected
9. Not connected
24. Not connected
10. Not connected
C1. Analog input Pr/Cr
11. Not connected
C2. Analog input Y
12. Not connected
C3. Analog input Pb/Cb
13. Not connected
C4. Not connected
14. Not connected
C5. Ground
15. Ground
55
Connecting Pin Assignments (Continued)
RS-232C Terminal : mini DIN 9 pin female connector
8
9
7
3
6
Pin No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Signal
Name
I/O
RD
SD
Receive Data
Send Data
SG
Signal Ground
RS
CS
Request to Send
Clear to Send
Input
Output
Reference
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to CS in internal circuit
Connected to RS in internal circuit
Not connected
4
5
2
1
RS-232C Terminal : D-sub 9 pin male connector of the DIN-D-sub RS-232C adaptor
1
6
5
Pin No. Signal
1.
2.
RD
3.
SD
4.
5.
SG
6.
7.
RS
8.
CS
9.
9
Name
I/O
Receive Data
Send Data
Input
Output
Signal Ground
Request to Send
Clear to Send
Reference
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to CS in internal circuit
Connected to RS in internal circuit
Not connected
RS-232C Cable recommended connection : D-sub 9 pin female connector
5
9
Pin No. Signal
CD
1.
RD
2.
SD
3.
ER
4.
SG
5.
DR
6.
RS
7.
CS
8.
CI
9.
1
6
Pin No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Signal
CD
RD
SD
ER
SG
DR
RS
CS
CI
Note
• Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the
controlling device (e.g. computer).
Projector
Pin No.
4
5
6
USB Terminal : Type B USB connector
4 3
Pin No.
1.
2.
3.
4.
1 2
56
Signal
VCC
USB–
USB+
SG
Name
USB power
USB data–
USB data+
Signal Ground
Computer
Pin No.
4
5
6
RS-232C Specifications and Commands
Computer control
A computer can be used to control the projector by connecting an RS-232C serial control
cable (cross type, commercially available) to the projector. (See page 24 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Parity bit: None
Baud rate*: 9,600 bps / 115,200 bps
Stop bit: 1 bit
Data length: 8 bits
Flow control: None
*Set the projector’s baud rate to the same rate as used by the computer.
Basic format
Commands from the computer are sent in the following order: command, parameter, and
return code. After the projector processes the command from the computer, it sends a response code to the computer.
Command format
C1
C2
C3 C4
P1
P2
P3
Command 4-digit
Response code format
Normal response
O
K
Return code (0DH)
P4
Return code (0DH)
Parameter 4-digit
Problem response (communication error or incorrect command)
E
R
R
Return code (0DH)
Info
• When controlling the projector using RS-232C commands from a computer, wait for at least 30
seconds after the power has been turned on, and then transmit the commands.
• After sending an input selection or picture adjustment command and then receiving an “OK” response code, the projector may take some time to process the command. If a second command is
sent while the projector is still processing the first command, you may receive an “ERR” response
code. If this happens, try resending the second command.
• When more than one code is being sent, send each command only after the response code for the
previous command from the projector is verified.
• “POWR????” “TABN _ _ _ 1” “TLPS _ _ _ 1” “TPOW _ _ _ 1” “TLPN _ _ _ 1” “TLTT _ _ _ 1”
“TLTM _ _ _ 1” “TLTL _ _ _ 1” “TNAM _ _ _ 1” “MNRD _ _ _ 1” “PJN0 _ _ _ 1”
- When the projector receives the special commands shown above:
* The on-screen display will not disappear.
* The “Auto Power Off” timer will not be reset.
- The special commands are available for applications that require continuous polling.
Note
• If an underbar (_) appears in the parameter column, enter a space.
• If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets
under Control Contents.
*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.
*2 This command should be sent only after the “IRGB _ _ _ 2” command is sent and an “OK” response
code is received.
*3 The Lamp Timer Reset command is available only in standby mode.
57
RS-232C Specifications and Commands (Continued)
Commands
Example: When turning on the projector, make the following setting.
Computer
P
O
W
R
_
_
_
→
←
1
Projector
O
K
RETURN
CONTROL CONTENTS
Power
Name
Input Change
Volume
Keystone
AV Mute
Freeze
Auto Sync
Resize
W
W
W
B
R
R
R
N
_ _ _
_ _ _
? ? ?
_ _ _
1
0
?
1
Power ON
P
P
P
T
Status
T L P S _ _ _ 1 0:Off, 1:On, 2:Retry
3:Waiting, 4:Lamp Error
T P O W _ _ _ 1 1:On, 2:Cooling
_
_
_
1
1
T L P N
T L T T _ _ _ 1 0 – 9999(Integer)
T L T M _ _ _ 1 0, 15, 30, 45
T L T L _ _ _ 1 0% – 100%(Integer)
T N A M _ _ _ 1 EIP2600/EIP250
M N R D _ _ _ 1 EIP-2600/EIP-250
P J N 1 * * * * OK or ERR
Power Status
Quantity
Usage Time(Hour)
Usage Time(Minute)
Life(Percentage)
Model Name Check
Model Name Check
Projector Name Setting 1
(First 4 characters) *1
Projector Name Setting 2
(Middle 4 characters) *1
Projector Name Setting 3
(Last 4 characters) *1
Projector Name Check
Computer
DVI
DVI-D-Computer select *2
DVI-D-Video select *2
DVI-Analog select *2
S-Video
Video
Input RGB Check
Input Video Check
Input Mode Check
Input Check
Volume(0 – 60)
Volume up/down(-10 – +10)
-80 – +80 (XGA)/-40 – +40 (SVGA)
On
Off
On
Off
Start
Normal
Computer
Stretch
Dot By Dot
Full
Border
Area Zoom
V-Stretch
Normal
DVI
Stretch
Dot By Dot
Full
Border
Area Zoom
V-Stretch
is only for EIP-2600.
58
O
O
O
A
PARAMETER
On
Off
Status
Projector Condition
Lamp
COMMAND
OK or ERR
OK
1
0: Normal
1: Temp High
8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
P J N 2 *
*
* * OK or ERR
P J N 3 *
*
* * OK or ERR
P
I
I
I
I
I
I
I
I
I
I
I
J
R
R
B
B
B
V
V
R
V
M
C
N
G
G
D
D
D
E
E
G
E
O
H
0
B
B
S
S
S
D
D
B
D
D
K
_
_
_
_
_
_
_
_
?
?
?
?
_
_
_
_
_
_
_
_
?
?
?
?
_
_
_
_
_
_
_
_
?
?
?
?
V
V
K
I
I
F
F
A
R
R
R
R
R
R
R
R
R
R
R
R
R
R
O
O
E
M
M
R
R
D
A
A
A
A
A
A
A
B
B
B
B
B
B
B
L
U
Y
B
B
E
E
J
S
S
S
S
S
S
S
S
S
S
S
S
S
S
A
D
S
K
K
Z
Z
S
R
R
R
R
R
R
R
R
R
R
R
R
R
R
_
_
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
_
_
_
_
_
_
_
_
_
_
1
1
_
_
_
_
_
1
1
2
1
2
3
1
2
?
?
?
?
*
*
*
1
0
1
0
1
1
2
3
5
6
0
1
1
2
3
5
6
1 0
1 1
Projector Name
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
1: Computer, 2: DVI (EIP-2600 only) or ERR
1: S-Video, 2: Video or ERR
1: RGB, 2: Video
1: Computer
2: DVI (EIP-2600 only)
3: S-Video
4: Video
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
Standby mode
(or 30-second startup time)
OK
OK or ERR
0
0: Normal
1: Temp High
2: Fan Error
4: Cover Open
8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
64: Temp Abnormally High
0:Off, 4:Lamp Error
0:Standby
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
RETURN
CONTROL CONTENTS
S-Video
Resize
Video
ALL Reset
Computer INPUT
Picture Mode
Contrast
Bright
Red
Blue
Color
Tint
Sharp
CLR Temp
BrilliantColorTM
(EIP-2600)
Bright Boost
(EIP-250)
Progressive
DNR
Picture Reset
Signal Type
Audio Input
DVI INPUT
Picture Mode
Normal
Stretch
Border
Area Zoom
V-Stretch
Normal
Stretch
Border
Area Zoom
V-Stretch
Standard
Presentation
Movie
Game
sRGB
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-1 – +1
0 – +2
2D Progressive
3D Progressive
Film Mode
Off
Level 1
Level 2
Auto
RGB
Compontent
Audio 1
Audio 2
Standard
Presentation
Movie
Game
sRGB
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-1 – +1
0 – +2
Contrast
Bright
Red
Blue
Color
Tint
Sharp
CLR Temp
BrilliantColorTM
(EIP-2600)
Bright Boost
(EIP-250)
Progressive
2D Progressive
3D Progressive
Film Mode
DNR
Off
Level 1
Level 2
Picture Reset
Signal Type
Auto
RGB
Compontent
Audio Input
Audio 1
Audio 2
Dynamic Range Auto
Standard
Enhanced
COMMAND
PARAMETER
*
*
*
*
*
*
*
_
_
_ 1 OK or ERR
_ 2 OK or ERR
_ 3 OK or ERR
1 0 OK or ERR
1 1 OK or ERR
_ 1 OK or ERR
_ 2 OK or ERR
_ 3 OK or ERR
1 0 OK or ERR
1 1 OK or ERR
_ 1 OK or ERR
1 0 OK or ERR
1 1 OK or ERR
1 2 OK or ERR
1 3 OK or ERR
1 4 OK or ERR
* * OK or ERR
* * OK or ERR
* * OK or ERR
* * OK or ERR
* * OK or ERR
* * OK or ERR
* * OK or ERR
* * OK or ERR
_ * OK or ERR
Standby mode
(or 30-second startup time)
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
*
*
*
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
1
1
1
1
*
*
*
*
*
*
*
*
_
0
1
2
0
1
2
1
0
1
2
1
2
0
1
2
3
4
*
*
*
*
*
*
*
*
*
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0
1
2
0
1
2
1
0
1
2
1
2
0
1
2
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
R
R
R
R
R
R
R
R
R
R
A
R
R
R
R
R
R
R
R
R
R
R
R
R
R
A
A
A
A
A
B
B
B
B
B
L
A
A
A
A
A
A
A
A
A
A
A
A
A
A
S
S
S
S
S
S
S
S
S
S
R
P
P
P
P
P
P
B
R
B
C
T
S
C
W
V
V
V
V
V
V
V
V
V
V
E
S
S
S
S
S
I
R
D
E
O
I
H
T
E
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
R
R
R
R
R
R
R
I
I
I
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
I
I
I
N
N
N
R
S
S
S
A
A
P
P
P
P
P
P
B
R
B
C
T
S
C
W
P
P
P
R
R
R
E
I
I
I
I
I
S
S
S
S
S
I
R
D
E
O
I
H
T
E
R
R
R
R
R
R
R
I
I
I
R
R
H
H
H
B
B
B
B
B
B
B
B
B
B
B
B
M
M
M
I
I
I
N
N
N
R
S
S
S
A
A
B
B
B
P
P
P
R
R
R
E
I
I
I
I
I
D
D
D
Power ON
is only for EIP-2600.
59
RS-232C Specifications and Commands (Continued)
RETURN
CONTROL CONTENTS
S-Video INPUT
Picture Mode
Contrast
Bright
Red
Blue
Color
Tint
Sharp
CLR Temp
BrilliantColorTM
(EIP-2600)
Bright Boost
(EIP-250)
Progressive
DNR
Picture Reset
Audio Input
Video INPUT
C.M.S. Setting
C.M.S.
Picture Mode
PARAMETER
Standard
Presentation
Movie
Game
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-1 – +1
0 – +2
V
V
V
V
V
V
V
V
V
V
V
V
V
A
A
A
A
A
A
A
A
A
A
A
A
A
P
P
P
P
P
B
R
B
C
T
S
C
W
S
S
S
S
I
R
D
E
O
I
H
T
E
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
*
*
*
*
_
_
1
1
1
1
*
*
*
*
*
*
*
*
_
0
1
2
3
*
*
*
*
*
*
*
*
*
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
Standby mode
(or 30-second startup time)
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
2D Progressive
3D Progressive
Film Mode
Off
Level 1
Level 2
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
I
I
I
N
N
N
R
A
A
P
P
P
P
P
B
R
B
C
T
S
C
W
P
P
P
R
R
R
E
I
I
S
S
S
S
I
R
D
E
O
I
H
T
E
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
*
*
*
*
_
_
_
_
_
_
_
_
_
_
_
1
1
1
1
*
*
*
*
*
*
*
*
_
0
1
2
0
1
2
1
1
2
0
1
2
3
*
*
*
*
*
*
*
*
*
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
V
V
V
V
V
V
V
V
V
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
I
I
I
N
N
N
R
A
A
C
C
H
H
H
H
H
H
R
S
S
S
S
S
S
R
V
V
V
V
V
V
R
R
P
P
P
R
R
R
E
I
I
S
S
R
Y
G
C
B
M
E
R
Y
G
C
B
M
E
R
Y
G
C
B
M
E
E
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
*
*
*
_
*
*
*
*
*
*
_
*
*
*
*
*
*
_
_
_
_
_
_
_
_
_
_
_
1
0
*
*
*
*
*
*
_
*
*
*
*
*
*
_
*
*
*
*
*
*
_
_
0
1
2
0
1
2
1
1
2
1
0
*
*
*
*
*
*
2
*
*
*
*
*
*
3
*
*
*
*
*
*
4
1
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
Audio 1
Audio 2
Standard
Presentation
Movie
Game
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-1 – +1
0 – +2
Contrast
Bright
Red
Blue
Color
Tint
Sharp
CLR Temp
BrilliantColorTM
(EIP-2600)
Bright Boost
(EIP-250)
Progressive
2D Progressive
3D Progressive
Film Mode
DNR
Off
Level 1
Level 2
Picture Reset
Audio Input
Audio 1
Audio 2
On
Off
Hue
Red
Yellow
Green
Cyan
Blue
Magenta
Reset
Saturation
Red
Yellow
Green
Cyan
Blue
Magenta
Reset
Value
Red
Yellow
Green
Cyan
Blue
Magenta
Reset
C.M.S. All Reset
is only for EIP-2600.
60
COMMAND
Power ON
RETURN
CONTROL CONTENTS
Clock
Phase
H-position
V-position
Fine Sync Adjustment Reset
Image Shift
OSD Display
Closed Caption
Video System
Background
Lamp Setting
Auto Sync
Auto Power Off
Auto Restart
STANDBY Mode
PRJ Mode
Language
-150 – +150
-30 – +30
-150 – +150
-60 – +60
-96 – +96 (XGA)/-75 – +75 (SVGA)
On
Off
Off
CC1
CC2
Auto
PAL
SECAM
NTSC4.43
NTSC3.58
PAL-M
PAL-N
PAL-60
Logo
Blue
None
Bright
Eco + Quiet
On
Off
On
Off
On
Off
Standard
Eco
On
Reverse
Off
On
Invert
Off
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
polski
Türkçe
Setup Guide
System Sound
Internal Speaker
RGB Frequency
Check
Fan Mode
Lamp Timer Reset *3
Magyer
On
Off
On
Off
On
Off
Horizontal
Vertical
Normal
High
COMMAND
I
I
I
I
I
L
I
I
C
C
C
M
M
M
M
M
M
M
M
I
I
I
T
T
A
A
A
A
A
A
M
M
I
I
I
I
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
S
S
S
S
A
A
T
T
H
H
L
N
N
A
A
A
N
M
M
L
L
L
E
E
E
E
E
E
E
E
M
M
M
H
H
A
A
P
P
R
R
O
O
M
M
M
M
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
S
S
S
S
F
F
L
L
P
C
P
H
V
R
D
D
D
C
C
C
S
S
S
S
S
S
S
S
B
B
B
M
M
D
D
O
O
E
E
U
U
R
R
I
I
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
G
G
N
N
P
P
R
R
M
M
R
L
H
P
P
E
S
I
I
A
A
A
Y
Y
Y
Y
Y
Y
Y
Y
G
G
G
D
D
J
J
W
W
S
S
T
T
E
E
N
N
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
U
U
D
D
K
K
Q
Q
D
D
E
PARAMETER
*
_
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0
*
*
*
*
_
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0
*
*
*
*
_
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
1
1
1
1
1
1
1
_
_
_
_
_
_
_
_
_
_
0
*
*
*
*
1
*
1
0
0
1
2
1
2
3
4
5
6
7
8
1
3
4
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
1
0
1
0
1
0
1
2
0
1
1
Power ON
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
kHz(***.* or ERR)
Hz(***.* or ERR)
OK or ERR
OK or ERR
ERR
Standby mode
(or 30-second startup time)
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
OK or ERR
61
Computer Compatibility Chart
Computer
• Multiple signal support
Pixel Clock: 12-170 MHz
Horizontal Frequency: 15-110 kHz,
Sync signal: Compatible with TTL level
• Compatible with sync on green signal
Vertical Frequency: 45-85 Hz,
The following is a list of modes that conform to VESA. However, this projector supports other
signals that are not VESA standards.
PC/MAC
Resolution
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
60
70
85
60
70
85
60
70
60
70
85
50
60
70
72
75
85
50
56
60
70
72
75
85
50
60
70
75
85
60
60
60
75
60
60
60
70
75
60
75
60
60
60
67
75
75
75
MAC 13"
MAC 16"
MAC 19"
SXGA+
UXGA
VGA
SVGA
XGA
1400 × 1050
1600 × 1200
640 × 480
832 × 624
1024 × 768
27.0
31.5
37.5
27.0
31.5
37.9
27.0
31.5
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.4
35.2
37.9
46.6
48.1
46.9
53.7
40.3
48.4
56.5
60.0
68.7
45.0
47.8
49.7
62.8
47.7
47.8
55.0
66.2
67.5
64.0
80.0
64.0
65.3
75.0
34.9
49.7
60.2
MAC 21"
SXGA
1152 × 870
68.7
640 × 350
640 × 400
720 × 350
VGA
720 × 400
640 × 480
SVGA
800 × 600
XGA
1024 × 768
PC
WXGA
1280
1280
1280
1280
1360
1366
×
×
×
×
×
×
720
768
800
800
768
768
1152 × 864
SXGA
1280 × 1024
1280 × 1024
VESA
Standard
* DVI-D
Support
Display
EIP-2600
EIP-250
✔
✔
✔
Upscale
✔
Upscale
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
True
✔
True
✔
✔
✔
✔
✔
✔
✔
Intelligent
Compression
Intelligent
Compression
✔
✔
Upscale
True
Intelligent
Compression
Upscale
Intelligent
Compression
* EIP-2600 only
Note
• When this projector receives 640K350 VESA format VGA signals, “640 × 400” appears on the screen.
• Optimum image quality will be achieved by matching your computer’s output resolution to the resolution
that corresponds to “True” in the “Display” column shown above.
• When “Screen resolution" of the computer is different from the resolution displayed on the projected image, follow the procedures shown below.
–Refer to “Select the resolution” for “Data image is not centered” on the Help menu and select the same
resolution as the resolution in “Screen resolution” of the computer.
–Depending on the computer you are using, the output signal may not be faithful to the “Screen resolution”
adjustment. Check the settings of the computer’s signal output. If the settings cannot be changed, it is
recommended that the resolution be set to the one that corresponds to “True” in the “Display” column.
DTV
Horizontal
Vertical
* DVI-D Support
Frequency (kHz) Frequency (Hz) (Compatible with HDCP)
480I
15.7
60
480P
✔
31.5
60
540P
33.8
60
576I
15.6
50
✔
576P
31.3
50
✔
720P
37.5
50
* EIP-2600 only
Signal
62
Signal
720P
1035I
1080I
1080I
1080P
1080P
Horizontal
Vertical
* DVI-D Support
Frequency (kHz) Frequency (Hz) (Compatible with HDCP)
✔
45.0
60
✔
33.8
60
✔
28.1
50
✔
33.8
60
✔
56.3
50
✔
67.5
60
Troubleshooting
Problem
Check
Projector power cord is not plugged into the wall outlet.
Power to the external connected devices is off.
The selected input mode is wrong.
Cables are incorrectly connected to the projector.
Remote control battery has run out.
External output has not been set when connecting notebook computer.
The lamp unit cover is not installed correctly.
EIP-2600 only: If the connected DVI digital equipment is turned on
before the “DVI-D” input mode is selected on the projector, the image
may not be projected properly or may not be displayed at all. Ensure
that the appropriate input mode has been selected on the projector
before you turn on the connected equipment.
• Cables are incorrectly connected to the projector.
• “Bright” is set to minimum position.
• Depending on the computer you are using, an image may not be
projected unless the signal output setting of the computer is
switched to the external output. Refer to the computer owner’s
manual for how to switch its signal output settings.
Page
24
–
29
21–24
14
21
53, 54
21
• Image adjustments are incorrectly set.
• Make adjustments of “Color” and “Tint” in “Picture Mode” and lower
the “BrilliantColorTM” (EIP-2600)/“Bright Boost” (EIP-250) value.
(Video Input only)
• Video input system is incorrectly set.
41
• Adjust the focus.
• The projection distance exceeds the focus range.
• There is fog on the lens. If the projector is carried from a cold room into a
warm room, or if it is suddenly heated, condensation may form on the
surface of the lens and the image will become blurred. Set up the
projector at least one hour before it is to be used. If condensation should
form, remove the power cord from the wall outlet and wait for it to clear.
(Computer Input only)
• Perform “Fine Sync” Adjustments (“Clock” Adjustment)
• Perform “Fine Sync” Adjustments (“Phase” Adjustment)
• Noise may appear depending on the computer.
• Cables are incorrectly connected to the projector.
26
20
–
• Volume is set to minimum.
• When the projector is connected to an external device and the
volume is set to minimum, the sound is not output even if you turn up
the volume of the external device.
29
• “Speaker” is set to “Off”.
45
•
•
•
•
•
•
No picture and no sound •
or projector does not
•
start.
21–24
41
–
Sound is heard but no
picture appears
(or picture is dark).
48
Color is faded or poor.
Picture is blurred;
noise appears.
Picture appears but no
sound is heard.
Data image is not
centered.
48
48
–
21–24
• Select “Data image is not centered” in the “Help” menu and make the 48
necessary adjustments.
–
• Depending on the computer you are using, the output resolution
signal may be different from the one you have set. For details, refer to
the owner’s manual of the computer.
63
Troubleshooting (Continued)
Problem
An unusual sound is
occasionally heard from
the cabinet.
Maintenance indicator on
the projector illuminates
or blinks in red.
The projector cannot
be turned on or put into
the standby mode
using STANDBY/ON on
the projector.
Picture is green on
COMPUTER
(Component)/
*DVI (Component).
Picture is pink
(no green) on
COMPUTER (RGB)/
*DVI (RGB).
Picture is too bright and
whitish.
The cooling fan becomes
noisy.
The lamp does not light
up even after the
projector turns on.
The lamp suddenly turns
off during projection.
The image sometimes
flickers.
The lamp needs much
time to turn on.
Picture is dark.
The remote control
cannot be used.
Check
Page
• If the picture is normal, the sound is due to cabinet shrinkage caused –
by room temperature changes. This will not affect operation or
performance.
50
• See “Maintenance Indicators”.
• The keylock is set.
If the keylock is set to “ON”, all the buttons are locked.
47
• Change the input signal type setting.
• When you cannot select an input signal type, select “Color is faded
or poor” in the “Help” menu, after selecting an item other than
“sRGB” in “Picture Mode”, and then select an input signal type.
48
40, 48
• Image adjustments are incorrectly set.
41
• When temperature inside the projector increases, the cooling fan
runs faster.
• The lamp indicator is illuminating in red.
Replace the lamp.
8, 9
49, 50, 51
50, 53
• Cables are incorrectly connected to the projector or the connected
equipment works improperly.
• Select “Vertical stripes or flickering image appear” in the “Help”
menu and make the necessary adjustments.
• If this happens frequently, replace the lamp.
• The lamp will eventually need to be changed.
While the remaining lamp life draws to a close, replace the lamp.
• Operate the remote control while pointing it at the projector’s remote
control sensor.
• The remote control may be too far away from the projector.
• If direct sunlight or a strong fluorescent lamp is shining on the
projector’s remote control sensor, place the projector where it will not
be affected by strong light.
• The batteries may be depleted or inserted incorrectly. Make sure the
batteries are inserted correctly or insert new ones.
21–24
48
53
53
15
14
* EIP-2600 only
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation
or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.
64
Specifications
Model
Display devices
Resolution
Lens
F number
Zoom
Focus
Input terminals
DVI-I (Compatible with HDCP)
RGB/Component (mini D-sub 15 pin)
S-Video (mini DIN 4 pin)
Video (RCA)
Audio (ø3.5 mm stereo minijack)
Audio (RCA)
Output terminals RGB/Component (mini D-sub 15 pin)
Audio (ø3.5 mm stereo minijack)
Control, others
USB (Type B)
RS-232C (mini DIN 9 pin)
Speakers
Projection lamp
Rated voltage
Rated frequency
Input current
Power consumption (Standby)
Operation temperature
Cabinet
Dimensions (main body only) [W × H × D]
Weight (approx.)
EIP-2600
EIP-250
0.55" DLP® Chip
XGA (1024×768)
SVGA (800×600)
F 2.5 – 2.6
Manual, ×1.15 (f = 20.4 – 23.5 mm)
Manual
×1
–
×1
×1
×1
×1
–
×1 (L/R)
×1
×1 (variable audio output) –
×1
×1
2 W (Mono)
230 W
200W
AC 100 – 240 V
50/60 Hz
3.2 A
2.9 A
303 W (5.0 W) with AC 100 V 267 W (5.0 W) with AC 100 V
293 W (5.7 W) with AC 240 V 259 W (5.7 W) with AC 240 V
41°F to 95°F (+5°C to +35°C)
Plastic
10 41/64" × 3 33/64" × 10 7/16"
(270 × 89 × 265 mm)
6.4 lbs. (2.9 kg)
As a part of policy of continuous improvement, EIKI reserves the right to make design and
specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
This EIKI projector uses a DLP® chip. This very sophisticated panel contains 786,432
(EIP-2600)/480,000 (EIP-250) pixels (micromirrors). As with any high technology electronic
equipment such as large screen TVs, video systems and video cameras, there are certain
acceptable tolerances that the equipment must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots
on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
65
Dimensions
3 33/64 (89)
1 31/64
2 5/8 (66.35) (37.65)
13/32
(10)
10 7/16 (265)
1/4
(6)
Units: inches (mm)
2 61/64 (75)
10
41/64
2 3/8 (60)
(270)
M4
13/32
(10)
M4
13/32
(10)
2 61/64 (75)
66
1 3/16
(30)
M4
1 27/64
(36)
1 15/16
(49)
4 7/64 (104)
M4
Index
3 RCA to mini D-sub 15 pin cable .......................... 22
Accessories ............................................................. 10
AC socket ................................................................ 24
Adjustment buttons ................................................. 38
AREA ZOOM ........................................................... 31
Aspect ratio ............................................................. 30
Audio Input .............................................................. 46
AUDIO 1, 2 terminal ................................................ 23
AUDIO OUT terminal .............................................. 23
Auto Power Off ........................................................ 45
Auto Restart ............................................................ 45
Auto Sync (Auto Sync adjustment) ....... 33, 37, 45, 48
AUTO SYNC button ................................................. 33
AV MUTE button ...................................................... 29
Background .............................................................
Batteries ..................................................................
Blue ..........................................................................
BORDER ........................................................... 30,
BREAK TIMER button .............................................
Bright .......................................................................
Bright Boost .............................................................
BrilliantColorTM .........................................................
44
14
41
31
32
41
41
41
Closed Caption ........................................................
CLR Temp (Color Temperature) ..............................
C.M.S. ......................................................................
Color ........................................................................
COMPUTER button .................................................
COMPUTER/COMPONENT input terminal ...... 21,
Contrast ...................................................................
44
41
41
41
29
22
41
DIN-D-sub RS-232C adaptor ..................................
DNR .........................................................................
DOT BY DOT ...........................................................
DVI button ................................................................
DVI-I input terminal ........................................... 21,
24
42
30
29
22
ECO+QUIET button ................................................ 32
ENTER button ......................................................... 38
Exhaust vent ...................................................... 11, 49
Fan Mode .................................................................
Fine Sync .................................................................
Focus ring ................................................................
FREEZE button .......................................................
Front adjustment foot ..............................................
FULL ........................................................................
46
48
26
33
27
30
HEIGHT ADJUST lever ........................................... 27
Help ......................................................................... 48
H-Pos ................................................................. 37, 48
Image shift ............................................................... 43
INPUT modes .......................................................... 29
Intake vent ......................................................... 11, 49
Kensington Security Standard connector ...............
Keycode ...................................................................
Keylock ....................................................................
KEYSTONE button ..................................................
Keystone Correction .......................................... 28,
12
46
47
28
43
Lamp ........................................................................
Lamp indicator .........................................................
Lamp Setting ...........................................................
Lamp Timer (Life) ....................................................
52
50
42
47
Lamp unit .................................................................
Language (on-screen display language) ................
L-CLICK/EFFECT button .................................. 32,
Lens Cap .................................................................
53
44
34
11
MAGNIFY buttons ...................................................
MENU/HELP button .......................................... 38,
MONITOR OUT terminal .........................................
MOUSE/Adjustment buttons ............................. 34,
33
48
23
38
NORMAL ........................................................... 30, 31
ON button ................................................................ 25
Optional accessories ............................................... 10
OSD Display ............................................................ 43
PAGE DOWN button ................................................ 34
PAGE UP button ...................................................... 34
PDF ............................................................................ 9
Picture Adjustment .................................................. 40
Picture Mode ..................................................... 33, 40
PICTURE MODE button .......................................... 33
POINTER button ..................................................... 32
Power cord ............................................................... 24
Power indicator ........................................................ 50
PRJ - ADJ ................................................................ 45
PRJ Mode .......................................................... 19, 44
Progressive .............................................................. 42
R-CLICK/RETURN button ................................. 34,
Rear adjustment foot ...............................................
Red ..........................................................................
Remote control ........................................................
Remote control sensor ............................................
Replacing the lamp ........................................... 52,
Resize ................................................................ 30,
RESIZE button ........................................................
RGB cable ...............................................................
RS-232C terminal ....................................................
38
27
41
13
15
53
43
30
21
24
SCR - ADJ ...............................................................
Screen Size and Projection Distance .....................
Setup Guide ....................................................... 26,
Sharp .......................................................................
Speaker ...................................................................
SPOT button ............................................................
STANDBY button .....................................................
STANDBY Mode ......................................................
STANDBY/ON button ..............................................
STRETCH .......................................................... 30,
Supplied accessories ..............................................
S-VIDEO button .......................................................
S-VIDEO terminal ....................................................
System Lock ............................................................
System Sound .........................................................
43
20
44
41
45
32
25
45
25
31
10
29
22
46
45
Temperature warning indicator ............................... 50
Tint ........................................................................... 41
USB terminal ........................................................... 34
VIDEO button ..........................................................
VIDEO terminal .......................................................
VOL (Volume) buttons .............................................
V-Pos ................................................................. 37,
V-STRETCH ............................................................
29
22
29
48
31
Zoom ring ................................................................ 26
67
U.S.A.
Canada
EIKI International, Inc.
30251 Esperanza
Rancho Santa Margarita
CA 92688-2132
U.S.A.
Tel : 800-242-3454 (949)-457-0200
Fax : 800-457-3454 (949)-457-7878
E-Mail : usa@eiki.com
EIKI CANADA - Eiki International, Inc.
P.O. Box 156, 310 First St. - Unit 2,
Midland, ON, L4R 4K8, Canada
Tel : 800-563-3454 (705)-527-4084
Fax : 800-567-4069 (705)-527-4087
E-Mail : canada@eiki.com
Deutschland & Österreich
Eastern Europe
EIKI Deutschland GmbH
Am Frauwald 12
65510 Idstein
Deutschland
Tel : 06126-9371-0
Fax : 06126-9371-14
E-Mail : info@eiki.de
EIKI CZECH spol. s.r.o.
Umelecká 15
170 00 Praha 7
Czech Republic
Tel : +42 02 20570024
+42 02 20571413
Fax : +42 02 20571411
E-Mail : easterneurope@eiki.de
China
Japan & Worldwide
EIKI (Shanghai) Co.,LTD
1. Dapu Road, Golden Magnolia Plaza
#2109 Shanghai,
200023 China
Tel : 86-21-5396-0088
Fax : 86-21-5396-0318
E-Mail : info@eiki-china.com
EIKI Industrial Company Limited.
4-12 Banzai-Cho, Kita-Ku, Osaka,
530-0028 Japan
Tel : +81-6-6311-9479
Fax : +81-6-6311-8486
WorldWide Website http://www.eiki.com
Download PDF