Canon | LV-8320 | multimedia projector lv-8320 expand serial command

MULTIMEDIA PROJECTOR LV-8320
EXPAND SERIAL COMMAND
FUNCTIONAL SPECIFICATIONS
Revision 1
© 2011 CANON INC.
YT1-1441-000
LV-8320 Expand Serial Command Functional Specifications
Table of Contents
1.Overview .............................................................................. 1
2.Serial Interface Specification................................................ 2
2.1 Transfer Specification .................................................................................................. 2
2.2 Connection .................................................................................................................... 2
3.Notes for communication ..................................................... 3
4.Name Definition ................................................................... 4
5.Functional Execution Command Table ................................ 5
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
Image Command Table ................................................................................................ 5
PC Adjust Control Command Table ............................................................................. 5
Input Control Command Table .................................................................................... 5
Screen Command Table................................................................................................ 6
Lamp Command Table ................................................................................................. 6
Sound Command Table ................................................................................................ 6
Setting Command Table ............................................................................................... 7
Other Command Table ................................................................................................. 7
6.Status Read Command Table .............................................. 8
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
Image Status Read Command Table ........................................................................... 8
PC Adjust Status Read Command Table ..................................................................... 8
Video Status Read Command Table ............................................................................ 8
Input Status Read Command Table ............................................................................ 8
Screen Status Read Command Table .......................................................................... 9
Lamp Status Read Command Table ............................................................................ 9
Sound Status Read Command Table ........................................................................... 9
Setting Status Read Command Table ....................................................................... 10
Other Status Read Command .................................................................................... 10
7.Error Code Table ................................................................ 11
8.Functional Execution Command ........................................ 12
8.1
8.2
8.3
8.4
Format ........................................................................................................................ 12
Transfer Example ....................................................................................................... 12
Operation Requirements ............................................................................................ 12
Image Command ........................................................................................................ 13
8.4.1 CF_BRIGHT Command ............................................................................ 13
8.4.2 CF_CONT Command ................................................................................ 13
8.4.3 CF_COLOR Command .............................................................................. 13
8.4.4 CF_TINT Command .................................................................................. 13
8.4.5 CF_SHARP Command .............................................................................. 14
8.4.6 CF_GAMMA Command............................................................................. 14
8.4.7 CF_WBAL - Command .............................................................................. 15
8.4.8 CF_COLTEMP Command ......................................................................... 15
8.4.9 CF_PROGV Command .............................................................................. 15
8.4.10 CF_NZRED Command ............................................................................ 16
8.4.11 CF_IMAGE Command ............................................................................ 16
8.4.12 CF_COLBOARD Command .................................................................... 17
-ii-
LV-8320 Expand Serial Command Functional Specifications
8.4.13 CF_IMAGEADJ Command ..................................................................... 17
8.5 PC Adjust Control Command ..................................................................................... 18
8.5.1 CF_FSYNC Command .............................................................................. 18
8.5.2 CF_TDOTS Command .............................................................................. 18
8.5.3 CF_CLAMP Command .............................................................................. 18
8.5.4 CF_H – POS Command ............................................................................. 19
8.5.5 CF_V – POS Command ............................................................................. 19
8.5.6 CF_DDOTS Command .............................................................................. 19
8.5.7 CF_DLINE Command ............................................................................... 20
8.5.8 CF_PCSTORE Command.......................................................................... 20
8.5.9 CF_PCMODEFREE Command ................................................................ 20
8.6 Input Control Command ............................................................................................ 21
8.6.1 CF_INPUT Command ............................................................................... 21
8.6.2 CF_SOURCE Command ........................................................................... 21
8.6.3 CF_INPUT1 Command ............................................................................. 22
8.6.4 CF_INPUT2 Command ............................................................................. 22
8.6.5 CF_INPUT3 Command ............................................................................. 22
8.6.6 CF_INPUT4 Command ............................................................................. 22
8.6.7 CF_INPUT5 Command ............................................................................. 22
8.6.8 CF_INPUT_%1_%2 Command ................................................................. 23
8.6.9 CF_SYSTEM Command ............................................................................ 24
8.7 Screen Control Command .......................................................................................... 25
8.7.1 CF_SCREEN Command............................................................................ 25
8.7.2 CF_DZCENT Command............................................................................ 25
8.7.3 CF_VSCALE Command ............................................................................ 26
8.7.4 CF_VPOS Command ................................................................................. 26
8.7.5 CF_HSCALE Command ............................................................................ 27
8.7.6 CF_HPOS Command ................................................................................. 27
8.7.7 CF_KEYSTONE Command ...................................................................... 28
8.7.8 CF_KYSTNMODE Command ................................................................... 28
8.7.9 CF_CEIL Command .................................................................................. 28
8.7.10 CF_REAR Command ............................................................................... 28
8.7.11 CF_SCREENASPECT Command ........................................................... 29
8.8 Lamp Command ......................................................................................................... 30
8.8.1 CF_LAMPMODE Command ..................................................................... 30
8.8.2 CF_ LAMPLIFECONTRL Command ....................................................... 30
8.9 Sound Command ........................................................................................................ 31
8.9.1 CF_VOLUME Command .......................................................................... 31
8.9.2 CF_MUTE Command ................................................................................ 31
8.9.3 CF_MIC Command.................................................................................... 31
8.9.4 CF_MICGAIN Command .......................................................................... 31
8.9.5 CF_STANDBYMICOUT Command .......................................................... 32
8.10 Setting Command ..................................................................................................... 33
8.10.1 CF_LANG Command .............................................................................. 33
8.10.2 CF_MENUPOSITION Command ........................................................... 33
8.10.3 CF_INPUTSEARCH Command ............................................................. 34
8.10.4 CF_AUTOSETUPPCADJ Command...................................................... 34
8.10.5 CF_AUTOSETUPKEYSTONE Command ............................................. 34
8.10.6 CF_AUTOSETUP Command .................................................................. 34
8.10.7 CF_BACKGND Command ...................................................................... 35
8.10.8 CF_DISP Command ................................................................................ 35
8.10.9 CF_LOGO Command .............................................................................. 36
8.10.10 CF_ HDMI SETUP Command .............................................................. 36
8.10.11 CF_HDMI SOUND Command .............................................................. 36
8.10.12 CF_TERMINAL Command ................................................................... 37
8.10.13 CF_PIP Command ................................................................................. 37
8.10.14 CF_PIPSIZE Command ........................................................................ 37
8.10.15 CF_PIPPOSITION Command .............................................................. 38
8.10.16 CF_P-MANE Command ........................................................................ 38
-iii-
LV-8320 Expand Serial Command Functional Specifications
8.10.17 CF_P-MANETIME Command .............................................................. 38
8.10.18 CF_ON-STA Command ......................................................................... 39
8.10.19 CF_STANDBYMODE Command .......................................................... 39
8.10.20 CF_PTIMEMODE Command ............................................................... 39
8.10.21 CF_PTIMER Command ........................................................................ 39
8.10.22 CF_PTIME Command ........................................................................... 40
8.10.23 CF_CCAPTIONDISP Command........................................................... 40
8.10.24 CF_CCAPTIONCOLOR Command ...................................................... 40
8.10.25 CF_RCODE Command .......................................................................... 41
8.10.26 CF_KEYDIS Command ......................................................................... 41
8.10.27 CF_PJPINCODE Command ................................................................. 41
8.10.28 CF_FANMODE Command .................................................................... 42
8.10.29 CF_FANCONTROL Command ............................................................. 42
8.10.30 CF_DELAYCTRL Command ................................................................. 42
8.10.31 CF_FILTIMER Command ..................................................................... 42
8.10.32 CF_FILH Command .............................................................................. 43
8.10.33 CF_TTLPWRSAVE Command .............................................................. 43
8.10.34 CF_FDEFAULT Command ................................................................... 43
8.11 Other Command ....................................................................................................... 44
8.11.1 CF_KEYENU Command ......................................................................... 44
8.11.2 CF_MENU Command ............................................................................. 44
8.11.3 CF_POWER Command ........................................................................... 44
8.11.4 CF_FREEZE Command .......................................................................... 45
8.11.5 CF_VMUTE Command ........................................................................... 45
9.Status Read Command ...................................................... 46
9.1
9.2
9.3
9.4
Format ........................................................................................................................ 46
Transfer Example ....................................................................................................... 46
Operation Condition ................................................................................................... 46
Image Status Read Command ................................................................................... 46
9.4.1 CR_BRIGHT Command ............................................................................ 46
9.4.2 CR_CONT Command ................................................................................ 46
9.4.3 CR_COLOR Command .............................................................................. 47
9.4.4 CR_TINT Command .................................................................................. 47
9.4.5 CR_SHARP Command .............................................................................. 47
9.4.6 CR_GAMMA Command ............................................................................ 47
9.4.7 CR_WBAL – R Command ......................................................................... 47
9.4.8 CR_WBAL – G Command ......................................................................... 47
9.4.9 CR_WBAL – B Command ......................................................................... 48
9.4.10 CR_COLTEMP Command ....................................................................... 48
9.4.11 CR_NZRED Command ............................................................................ 48
9.4.12 CR_PROGV Command ............................................................................ 48
9.4.13 CR_IMAGE Command ............................................................................ 49
9.4.14 CR_IMGGMD Command ........................................................................ 49
9.4.15 CR_COLBOARD Command .................................................................... 49
9.5 PC Adjust Status Read Command ............................................................................. 50
9.5.1 CR_FSYNC Command .............................................................................. 50
9.5.2 CR_TDOTS Command .............................................................................. 50
9.5.3 CR_CLAMP Command.............................................................................. 50
9.5.4 CR_H – POS Command ............................................................................ 50
9.5.5 CR_V – POS Command ............................................................................. 50
9.5.6 CR_DDOTS Command .............................................................................. 51
9.5.7 CR_DLINE Command ............................................................................... 51
9.5.8 CR_PCSTORE Command ......................................................................... 51
9.6 Video Status Read Command .................................................................................... 52
9.6.1 CR_SERSYS Command ............................................................................ 52
9.7 Input Status Read Command .................................................................................... 53
9.7.1 CR_INPUT Command ............................................................................... 53
9.7.2 CR_SOURCE Command ........................................................................... 53
-iv-
LV-8320 Expand Serial Command Functional Specifications
9.8
9.9
9.10
9.11
9.7.3 CR_SRCINP1 Command ........................................................................... 53
9.7.4 CR_SRCINP2 Command ........................................................................... 53
9.7.5 CR_SRCINP3 Command ........................................................................... 53
9.7.6 CR_SRCINP4 Command ........................................................................... 54
9.7.7 CR_SRCINP5 Command ........................................................................... 54
9.7.8 CR_SYSTEM Command ........................................................................... 55
9.7.9 CR_SYSLIST Command ........................................................................... 56
9.7.10 CR_MODELIST Command ..................................................................... 56
Screen Status Read Command .................................................................................. 57
9.8.1 CR_SCREEN Command ........................................................................... 57
9.8.2 CR_VSCALE Command ............................................................................ 57
9.8.3 CR_VPOS Command ................................................................................. 57
9.8.4 CR_HSCALE Command ........................................................................... 57
9.8.5 CR_HPOS Command ................................................................................ 58
9.8.6 CR_ KYSTNMODE Command ................................................................. 58
9.8.7 CR_CEIL Command .................................................................................. 58
9.8.8 CR_REAR Command................................................................................. 58
9.8.9 CR_SCREENASPECT Command............................................................. 58
Lamp Status Read Command .................................................................................... 59
9.9.1 CR_LAMPREPL Command ...................................................................... 59
9.9.2 CR_LAMPH Command ............................................................................. 59
9.9.3 CR_LAMPCORRESPH Command ........................................................... 59
9.9.4 CR_LAMPMODE Command..................................................................... 59
9.9.5 CR_LAMPMSTS Command ...................................................................... 60
9.9.6 CR_PROJH Command .............................................................................. 60
9.9.7 CR_HMLAMP Command .......................................................................... 60
9.9.8CR_ LAMPLIFECONTRL Command .......................................................... 60
Sound Status Read Command ................................................................................. 61
9.10.1 CR_VOLUME Command ........................................................................ 61
9.10.2 CR_MUTE Command.............................................................................. 61
9.10.3 CR_MIC Command ................................................................................. 61
9.10.4 CR_MICGAIN Command ........................................................................ 61
9.10.5 CR_STANDBYMICOUT Command........................................................ 61
Setting Status Read Command ................................................................................ 62
9.11.1 CR_LANG Command .............................................................................. 62
9.11.2 CR_INPUTSEARCH Command ............................................................. 62
9.11.3 CR_AUTOSETUPPCADJ Command...................................................... 62
9.11.4 CR_AUTOSETUPKEYSTONE Command ............................................. 63
9.11.5 CR_BACKGND Command ...................................................................... 63
9.11.6 CR_DISP Command ................................................................................ 63
9.11.7 CR_LOGO Command .............................................................................. 63
9.11.8 CR_HDMI SETUP Command ................................................................. 63
9.11.9 CR_HDMI SETUPSOUND Command ................................................... 64
9.11.10 CR_TERMINAL Command ................................................................... 64
9.11.11 CR_PIP Command ................................................................................. 64
9.11.12 CR_PIPSIZE Command ........................................................................ 64
9.11.13 CR_PIPPOSITION Command .............................................................. 64
9.11.14 CR_P-MANE Command ........................................................................ 65
9.11.15 CR_P-MANETIME Command .............................................................. 65
9.11.16 CR_ON-STA Command ......................................................................... 65
9.11.17 CR_STANDBYMODE Command .......................................................... 65
9.11.18 CR_PTIMEMODE Command ............................................................... 65
9.11.19 CR_PTIMER Command ........................................................................ 66
9.11.20 CR_PTIME Command ........................................................................... 66
9.11.21 CR_CCAPTIONDISP Command........................................................... 66
9.11.22 CR_CCAPTIONCOLOR Command ...................................................... 66
9.11.23 CR_RCODE Command .......................................................................... 66
9.11.24 CR_SECURITY Command .................................................................... 67
9.11.25 CR_KEYDIS Command ......................................................................... 67
-v-
LV-8320 Expand Serial Command Functional Specifications
9.11.26 CR_PJLOCKNOW Command ............................................................... 67
9.11.27 CR_PJLOCKMENU Command ............................................................ 67
9.11.28 CR_FANMODE Command .................................................................... 67
9.11.29 CR_FANCONTROL Command ............................................................. 68
9.11.30 CR_ DELAYCTRL Command ................................................................ 68
9.11.31 CR_FILH Command .............................................................................. 68
9.11.32 CR_FILREPL Command ....................................................................... 68
9.11.33 CR_FILTIMER Command ..................................................................... 68
9.11.34 CR_TTLPWRSAVEKWH Command..................................................... 69
9.11.35 CR_TTLPWRSAVECO2 Command ...................................................... 69
9.12 Other Status Read Command .................................................................................. 70
9.12.1 CR_STATUS Command .......................................................................... 70
9.12.2 CR_SIGNAL Command........................................................................... 70
9.12.3 CR_VMUTE Command ........................................................................... 70
9.12.4 CR_FREEZE Command .......................................................................... 70
9.12.5 CR_TEMPWARN Command ................................................................... 71
9.12.6 CR_TEMP Command .............................................................................. 72
9.12.7 CR_TEMPFAIL Command ...................................................................... 73
9.12.8 CR_SERIALNO Command ..................................................................... 73
-vi-
LV-8320 Expand Serial Command Functional Specifications
1.Overview
1.1
This Functional Specification defines communication functions for LV-8320.
1.2
Compatible to Firmware Ver. 1.x of the projector.
1.3
Most commands can be used to control projector remotely from PC by RS-232C. Therefore, the
commands are defined as Expand Serial Commands.
-1-
LV-8320 Expand Serial Command Functional Specifications
2.Serial Interface Specification
2.1 Transfer Specification
Item
Specification
Synchronous System
Asynchronous
Transmission Speed
9600 / 19200
Data Length
8 bit
Parity
N/A
Stop Bit
1
Flow Control
N/A
Note1) Transmission Speed: initial setting value is 19200
Note2) Transmission Speed can be changed in service mode.
2.2 Connection
Dedicated serial cable must be used for a connection to a computer and a projector.
PC
Projector
COM 1
Control Port
(D-Sub 9 Pin)
(D-Sub 9 Pin)
-2-
LV-8320 Expand Serial Command Functional Specifications
3.Notes for communication
1.
Expand Serial Command is defined as one command / one line that starts with “C” and ends
with carriage return (0x0D)
2.
There are two types of commands: Functional Execution Command and Status Read
Command.
- Example of Functional Execution Command:”CF_BRIGHT_032”[CR]
- Example of Status Read Command: “CR_RIGHT”[CR]
Note) ”_” means a space
3.
When it takes more than one second to receive one command, it is not executed.
When it takes more than one second to receive carriage return (0X0D) after the projector
receives the first data “C”, it clears the information of buffer.
4.
On command pipelining, wait for the interval of 100ms till sending next command after receiving
a response.
(More than 100ms)
Command
PC → Projector
“CF_BRIGHT_032” CR
Projector → PC
Next Command
“000” CR
Response
(A few ms - 5s)
When a computer sends next command before receiving a response, the projector may not
operate properly, except when there is no response for more than 5 seconds.
5.
It takes about 5 seconds for internal initialization after plugging in AC power. During this time
commands cannot be processed. Do not issue any command.
-3-
LV-8320 Expand Serial Command Functional Specifications
4.Name Definition
1.
Data from a controller to a projector is represented as COMMAND, and data from a projector to
a controller for the incoming command is represented as RESPONSE.
2.
[CR] : Carriage Return Code
Command ends with cartridge return code.
Response also ends with carriage return code.
3.
_ : Space Code
A space Code is indicated by (_).
4.
%1 : Parameter in Command
When there are several parameters, they are defined as %2, %3…
5.
%%% : Error code returned from a projector
Acceptable: “000”.
Unacceptable: See [7. Error Code Table].
6.
%a : Parameter in Response Command
When there are several parameters, they are defined as %b, %c…
-4-
LV-8320 Expand Serial Command Functional Specifications
5.Functional Execution Command Table
5.1
Image Command Table
Execute command
Item
Set Brightness value
CF_BRIGHT_%1[CR]
CF_CONT_%1[CR]
CF_COLOR_%1[CR]
CF_TINT_%1[CR]
CF_SHARP_%1[CR]
CF_GAMMA_%1[CR]
CF_WBAL-R_%1[CR]
CF_WBAL-G_%1[CR]
CF_WBAL-B_%1[CR]
CF_COLTEMP_%1[CR]
CF_PROGV_%1[CR]
CF_NZRED_%1[CR]
CF_IMAGE_%1[CR]
CF_COLBOARD_%1[CR]
CF_IMAGEADJ_%1[CR]
5.2
Set Contrast value
Set Color value
Set Tint value
Set Sharpness value
Set Gamma value
Set White Balance Red value
Set White Balance Green value
Set White Balance Blue value
Set Color Temp. value
Set /Cancel Progressive Scan
Set/Cancel Noise reduction
Set Image mode
Set Colorboard mode
Reset/Store for Image Adjustment
PC Adjust Control Command Table
Execute command
CF_FSYNC_%1[CR]
CF_TDOTS_%1[CR]
CF_CLAMP_%1[CR]
CF_H-POS_%1[CR]
CF_V-POS_%1[CR]
CF_DDOTS_%1[CR]
CF_DLINE_%1[CR]
CF_PCSTORE_%1[CR]
CF_PCMODEFREE_%1[CR]
5.3
Item
Set Fine Sync value
Set Total Dots value
Set Clamp Value
Set Horizontal Position value
Set Vertical Position value
Set Display Dots value
Set Display Line value
Store current values of PC Adjust at Mode 1-10
Release registered values of Mode1-10
Input Control Command Table
Execute command
CF_INPUT_%1[CR]
CF_SOURCE_%1[CR]
CF_INPUT1 _%1[CR]
CF_INPUT2_%1[CR]
CF_INPUT3_%1[CR]
CF_INPUT4_%1[CR]
CF_INPUT5_%1[CR]
CF_INPUT_%1_%2[CR]
CF_SYSTEM_%1[CR]
Item
Select Input
Select Input Source
Select computer-1 and set Input selected in %1
Select computer-2 and set Input selected in %1
Select HDMI and set Input selected in %1
Select Video and set Input selected in %1
Select S-video and set Input selected in %1
Select Input and Source
Select System
-5-
LV-8320 Expand Serial Command Functional Specifications
5.4
Screen Command Table
Execute command
CF_SCREEN_%1[CR]
CF_DZCENT_%1[CR]
CF_VSCALE_%1[CR]
CF_VPOS_%1[CR]
CF_HSCALE_%1[CR]
CF_HPOS_%1[CR]
CF_KEYSTONE_%1[CR]
CF_KYSTNMODE_%1[CR]
CF_CEIL_%1[CR]
CF_REAR_%1[CR]
CF_SCREENASPECT_%1[CR]
5.5
Item
Select Aspect mode (screen size)
Cancel Digital Zoom mode
Set value of Vertical scale
Set value of Vertical position
Set value of Horizontal scale
Set value of Horizontal position
Set Keystone
Set Keystone Store mode
Set Ceiling function
Set Rear function
Set Screen aspect function
Lamp Command Table
Execute command
CF_LAMPMODE_%1[CR]
CF_LAMPLIFECONTRL_%1[CR]
5.6
Item
Select Lamp mode
Select Lamp life mode
Sound Command Table
Execute command
CF_VOLUME_%1[CR]
CF_MUTE_%1[CR]
CF_MIC_%1[CR]
CF_MICGAIN_%1[CR]
CF_STANDBYMICOUT_%1[CR]
Item
Set Volume value
Control ON/OFF of Sound Mute
Control ON/OFF of MIC
Control value of MIC GAIN
Control ON/OFF of STANDBY MIC OUT
-6-
LV-8320 Expand Serial Command Functional Specifications
5.7
5.8
Setting Command Table
Execute command
Item
CF_LANG_%1[CR]
CF_MENUPOSITION_%1[CR]
CF_INPUTSEARCH_%1[CR]
CF_AUTOSETUPPCADJ_%1[CR]
CF_AUTOSETUPKEYSTONE_%1[CR]
CF_AUTOSETUP_%1[CR]
CF_BACKGND_%1[CR]
CF_DISP_%1[CR]
CF_LOGO_%1_%2[CR]
CF_HDMISETUP_%1[CR]
CF_HDMISOUND_%1[CR]
CF_TERMINAL_%1[CR]
CF_PIP_%1[CR]
CF_PIPSIZE_%1[CR]
CF_PIPPOSITION_%1[CR]
CF_P-MANE_%1[CR]
CF_P-MANETIME_%1[CR]
CF_ON-STA_%1[CR]
CF_STANDBYMODE_%1[CR]
CF_PTIMEMODE_%1[CR]
CF_PTIMER_%1[CR]
CF_PTIME_%1[CR]
CF_CCAPTIONDISP_%1[CR]
CF_CCAPTIONCOLOR_%1[CR]
CF_RCODE_%1[CR]
CF_KEYDIS_%1[CR]
CF_PJPINCODE_%1[CR]
CF_FANMODE_%1[CR]
CF_FANCONTROL_%1[CR]
CF_DELAYCTRL_%1[CR]
CF_FILTIMER_%1[CR]
CF_FILH_%1[CR]
CF_TTLPWRSAVE_%1[CR]
CF_FDEFAULT_%1[CR]
Select language for OSD
Move menu position.
Set up Auto input function
Set Auto PC in Auto Setup
Set Auto Keystone in Auto Setup
Execute Auto Setup
Set screen mode for the case of no signal
Set Display function
Set Logo function
Set Image mode of HDMI menu.
Set Sound mode of HDMI menu.
Set Terminal function
Select mode of Picture in Picture menu
Set Sub picture size for Picture in Picture
Set Sub picture position for Picture in Picture
Set Power management mode function
Set Power management mode time
Set Direct power on Start function
Set Standby Mode
Select P-timer mode
Execute P-timer
Set Countdown timer for P-timer
Set channel of Closed caption
Set color of Closed caption
Select Remote Control Reception Code
Disable RC/Projector keys
Input PIN code to release PJ Lock
Select Fan mode
Select Fan control mode
Set Video delay control
Set time when Filter warning OSD is displayed
Reset Filter used time
Reset the value of Total power savings
Set the value to Factory Default
Other Command Table
Execute command
CF_KEYEMU_%1[CR]
CF_MENU_%1[CR]
CF_POWER_%1[CR]
CF_FREEZE _%1[CR]
CF_VMUTE _%1[CR]
Item
Behave the same as corresponding key of
projector top panel
Switch ON/OFF of each Menu.
Switch ON/OFF of Power.
Set Freeze function.
Set Blank function.
-7-
LV-8320 Expand Serial Command Functional Specifications
6.Status Read Command Table
6.1
Image Status Read Command Table
Status read command
Item
Get Brightness value
Get Contrast value
Get Color value
Get Tint value
Get Sharpness value
Get Gamma value
White Balance Red value
White Balance Green value
White Balance Blue value
Get setting value of Color temperature
Get setting status of Noise reduction
Get setting status of Progressive scan
Get Selected Image status
Get setting value of Image Gamma
Get Selected Colorboard mode
CR_BRIGHT[CR]
CR_CONT[CR]
CR_COLOR[CR]
CR_TINT[CR]
CR_SHARP[CR]
CR_GAMMA[CR]
CR_WBAL-R[CR]
CR_WBAL-G[CR]
CR_WBAL-B[CR]
CR_COLTEMP[CR]
CR_NZRED[CR]
CR_PROGV[CR]
CR_IMAGE[CR]
CR_IMGGMD[CR]
CR_COLBOARD[CR]
6.2
PC Adjust Status Read Command Table
Status read command
Item
Get setting value of Fine Sync
Get setting value of Total Dots
Get setting value of Clamp
Get setting value of Horizontal Position
Get setting value of Vertical Position
Get setting value of Display Dots
Get setting value of Display Line
Get Free or Stored status for PC Adj. mode1-10
CR_FSYNC[CR]
CR_TDOTS[CR]
CR_CLAMP[CR]
CR_H-POS[CR]
CR_V-POS[CR]
CR_DDOTS[CR]
CR_DLINE[CR]
CR_PCSTORE[CR]
6.3
Video Status Read Command Table
Status read command
Item
Get selected current signal. When in Auto mode, it
returns a result by Auto detect.
CR_SERSYS[CR]
6.4
Input Status Read Command Table
Status read command
CR_INPUT[CR]
CR_SOURCE[CR]
CR_SRCINP1[CR]
CR_SRCINP2[CR]
CR_SRCINP3[CR]
CR_SRCINP4[CR]
CR_SRCINP5[CR]
CR_SYSTEM[CR]
CR_SYSLIST[CR]
CR_MODELIST[CR]
Item
Get selected Input No.
Get selected source of currently selected Input
Get selected source of Computer 1
Get selected source of Computer 2
Get selected source of HDMI
Get selected source of Video
Get selected source of S-video
Get selected system status in Input mode
Get selectable System table
Get selectable Mode table
-8-
LV-8320 Expand Serial Command Functional Specifications
6.5
Screen Status Read Command Table
Status read command
Item
Get selected Aspect mode (screen size)
Get setting status of Vertical Scale
Get setting status of Vertical Position
Get setting status of Horizontal Scale
Get setting status of Horizontal Position
Get setting status of Keystone Store mode
Get setting status of Ceiling
Get setting status of Rear
Get setting status of Screen aspect
CR_SCREEN[CR]
CR_VSCALE[CR]
CR_VPOS[CR]
CR_HSCALE[CR]
CR_HPOS[CR]
CR_KYSTNMODE[CR]
CR_CEIL [CR]
CR_REAR[CR]
CR_SCREENASPECT[CR]
6.6
Lamp Status Read Command Table
Status read command
CR_LAMPREPL[CR]
CR_LAMPH[CR]
CR_LAMPCORRESPH[CR]
CR_LAMPMODE[CR]
CR_LAMPSTS[CR]
CR_PROJH[CR]
CR_HMLAMP[CR]
CR_LAMPLIFECONTRL[CR]
6.7
Item
Get the information for Lamp replacement time
Get lamp total running time
Get corresponding lamp use time
Get Lamp Mode status
Get lamp lighting status
Get projector total running time
Get lamp number
Get setting status of Lamp life mode
Sound Status Read Command Table
Status read command
Item
CR_VOLUME[CR]
CR_MUTE[CR]
CR_MIC[CR]
CR_MICGAIN[CR]
CR_STANDBYMICOUT[CR]
Get Volume value
Get Sound Mute setting status
Get setting status of MIC
Get value of MIC GAIN
Get setting status of STANDBY MIC OUT
-9-
LV-8320 Expand Serial Command Functional Specifications
6.8
Setting Status Read Command Table
Status read command
Item
CR_LANG[CR]
CR_INPUTSEARCH[CR]
CR_AUTOSETUPPCADJ
CR_AUTOSETUPKEYSTONE
CR_BACKGND[CR]
CR_DISP[CR]
CR_LOGO[CR]
CR_HDMISETUP[CR]
CR_HDMISOUND[CR]
CR_TERMINAL[CR]
CR_PIP[CR]
CR_PIPSIZE[CR]
Get selected language
Get setting status of Auto input
Get setting status of Auto PC in Auto setup
Get setting status of Keystone in Auto setup
Get setting status screen mode for the case of no signal
Get setting status of Display
Get setting status of Logo
Get status of Image mode of HDMI setup.
Get status of Sound mode of HDMI setup.
Get setting status of Terminal
Get status of mode in Picture in Picture.
Get status of Sub picture size for Picture in Picture
Get status of position of Sub picture for Picture in
Picture.
Get setting status of Power management mode
Get setting time for Power management mode
Get setting status of Direct power on
Get setting status of Standby mode
Get selected mode of P-timer
Get operation status of P-timer
Get setting status of Timer for P-timer
Get setting status of channel of Closed caption
Get setting status of color of Closed caption
Get selected Remote Control Code
Get setting status of Security
Get RC/KEY disability status
Get if PJ Lock is actually in operation
Get setting status of PJ Lock on Menu
Get selected Fan mode
Get selected Fan Control Mode
Get setting status of Video delay control
Get Filter used time
Get the information for Filter replacement time
Get time when Filter warning OSD is displayed
Get current value (kWh) of Total power savings
Get current value (kg/CO2) of Total power savings
CR_PIPPOSITION[CR]
CR_P-MANE[CR]
CR_P-MANETIME[CR]
CR_ON-STA[CR]
CR_STANDBYMODE[CR]
CR_PTIMEMODE[CR]
CR_PTIMER[CR]
CR_PTIME[CR]
CR_CCAPTIONDISP[CR]
CR_CCAPTIONCOLOR[CR]
CR_RCODE[CR]
CR_SECURITY[CR]
CR_KEYDIS[CR]
CR_PJLOCKNOW[CR]
CR_PJLOCKMENU[CR]
CR_FANMODE[CR]
CR_FANCONTROL[CR]
CR_DELAYCTRL[CR]
CR_FILH[CR]
CR_FILREPL[CR]
CR_FILTIMER[CR]
CR_TTLPWRSAVEKWH[CR]
CR_TTLPWRSAVECO2[CR]
6.9
Other Status Read Command
Status read command
CR_STATUS[CR]
CR_SIGNAL[CR]
CR_VMUTE[CR]
CR_FREEZE[CR]
CR_TEMPWARN[CR]
CR_TEMP[CR]
CR_TEMPFAIL[CR]
CR_SERIALNO[CR]
Item
Get setting status of Projector behavior
Get Signal Status if there is a signal or not
Get setting status of Blank
Get setting status of Freeze
Get if temperature is close to abnormal temperature
Get current temperature status
Get temperature when sensors detect abnormal temperature
Get value of SERIAL NO.
-10-
LV-8320 Expand Serial Command Functional Specifications
7.Error Code Table
Error Code
?
Contents
-When the received data cannot be decoded
-Parameter determination error (digit number error,
including invalid value, etc.)
101
The function is not available in the selected Mode
102
Selected value is out of range (Not reflected)
103
Command mismatched to Hardware (command for
Optional function which is not installed)
201
When reached upper or lower limit of increasing or
decreasing data
301
Command cannot be executed during capturing
display. Resend the command after a while
302
Command cannot be executed during Auto PC
operation. Resend the command after a while
402
Command cannot be executed during PIN code
operation. Resend the command after a while.
Note) These error codes are applied to Expand Command, not to Basic Command
-11-
LV-8320 Expand Serial Command Functional Specifications
8.Functional Execution Command
8.1
1.
Format
PC issues commands in format as below:
Pattern1: “CF_COMMAND” [CR]
Pattern2: “CF_COMMAND_”%1 [CR]
CF_ : Header
COMMAND : Character line
%1 : Parameter (Character line)
_ : Space (To separate COMMAND and Parameter)
2.
The projector decodes the received command and when it is ready to receive the next command,
it returns the response.
“000” [CR] : (0x06, 0x0D) When receiving Functional Execution Command
“nnn” [CR] : Except “000” , when it is unable to execute command by any specific reason.
See Error Code Table for details
3.
8.2
When the received data cannot be decoded, the projector returns “?” [CR]
Transfer Example
When setting projector’s total dots to 1344 by Expand Serial Command
PC → PJ: ”CF_TDOTS_1344” [CR]
PC ← PJ: “000”[CR] - - - - - - - - - - - Acceptable
8.3
Operation Requirements
1) Functional Execution Command is limited when the projector status is as below.
However, Status Read Command is effective even under these conditions.
Projector Status
Available Functional Execution Command
In Standby
C00: POWER ON
C00: POWER ON
(Terminates Countdown)
C01: POWER OFF
C02: POWER OFF
(Terminates Countdown)
N/A
Countdown in process
Cooling down in process
Cooling down in process due to Abnormal
Temperature
Abnormal Temperature
Power Failure
(For 60 seconds after Power Failure occurred)
Power Save / Cooling down in process
Power Save in process
N/A
N/A
N/A
N/A
C00: POWER ON
C01: POWER OFF
Note:) When the projector receives the other command in this above status, it returns
error code to show the status.
When the projector receives the following functional execution commands, OSD
menu is closed except for pop-up menu
2) When Eco mode is selected in Standby mode of Setting menu and projector is in Standby,
Functional Execution Commands are invalid.
-12-
LV-8320 Expand Serial Command Functional Specifications
8.4
Image Command
8.4.1
CF_BRIGHT Command
Command
%1
Details
Response
8.4.2
%1
Details
Response
Set Brightness value of user control
Projector does not save the value set with this command so that it resets when
projector turning into Standby status or ALL is OFF. (The value is held in Suspend
mode.) This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
“CF_CONT_%1”[CR]
“000~063” --------------- Directly select Contrast setting value
“UP” ----------------------- Current Contrast setting value + 1
“DN” ----------------------- Current Contrast setting value – 1
Set Contrast value of user control
Projector does not save the value set with this command so that it resets when
projector turning into Standby status or ALL is OFF. (The value is held in Suspend
mode.) This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
"Error Code”[CR]
CF_COLOR Command
Command
%1
Details
Response
8.4.4
"000~063” --------------- Directly select Brightness setting value
"UP” ----------------------- Current Brightness setting value + 1
"DN” ----------------------- Current Brightness setting value – 1
CF_CONT Command
Command
8.4.3
"CF_BRIGHT_%1”[CR]
“CF_COLOR_%1”[CR]
“000~063” ---------------- Directly select Color setting value
“UP” ------------------------ Current Color setting value + 1
“DN” ------------------------ Current Color setting value - 1
Set Color value of user control
Projector does not save the value set with this command so that it resets when
projector turning into Standby status or ALL is OFF. (The value is held in Suspend
mode.)
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_TINT Command
Command
%1
Details
Response
“CF_TINT_%1”[CR]
“000~063” --------------- Directly select Tint setting value
“UP” ----------------------- Current Tint setting value + 1
“DN” ----------------------- Current Tint setting value – 1
Set Tint value of user control
Projector does not save the value set with this command so that it resets when
projector turning into Standby status or ALL is OFF. (The value is held in Suspend
mode.)
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-13-
LV-8320 Expand Serial Command Functional Specifications
8.4.5
CF_SHARP Command
Command
%1
Details
Response
8.4.6
“CF_SHARP_%1”[CR]
“000~015” ---------------- Directly select Sharpness setting value
“UP” ------------------------ Current Sharpness setting value + 1
“DN” ------------------------ Current Sharpness setting value - 1
Set Sharpness value of user control
Projector does not save the value set with this command so that it resets when
projector turning into Standby status or ALL is OFF. (The value is held in Suspend
mode.)
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_GAMMA Command
Command
%1
Details
Response
“CF_GAMMA_%1”[CR]
“000~015” ---------------- Directly set Gamma setting value
“UP” ------------------------ Current Gamma setting value + 1
“DN” ------------------------ Current Gamma setting value – 1
Set Gamma value of user control
Projector does not save the value set with this command so that it resets when
projector turning into Standby status or ALL is OFF. (The value is held in Suspend
mode.)
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-14-
LV-8320 Expand Serial Command Functional Specifications
8.4.7
CF_WBAL - Command
Command
“CF_WBAL-%1_%2”[CR]
%1
“R” --------------------- Red
“G” --------------------- Green
“B” --------------------- Blue
%2
“000~063” ----------- Directly select Color value specified by White Balance%1
“UP” ------------------- Current Color value set by White Balance%1 + 1
“DN” ------------------- Current Color value set by White Balance%1 - 1
Details
Response
8.4.8
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_COLTEMP Command
Command
%1
Details
Response
8.4.9
Set Color value set by White Balance%1 of user control
Projector does not save the value set with this command so that it resets when
projector turning into Standby status or ALL is OFF. (The value is held in Suspend
mode.)
This command is available in normal Power ON status.
“CF_COLTEMP_%1”[CR]
“000” ------ Xlow
“001” ------ Low
“002” ------ Mid
“003” ------ High
Set Color Temperature. (Available only in the normal Power ON status)
The value set by this command will not be saved to the projector. Therefore, when
turning into Standby-mode or ALL is OFF, the value returns to original setting. (The
value is held in Suspend mode.)
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_PROGV Command
Command
%1
Details
Response
“CF_PROGV_%1”[CR]
“FILM” -------- Select Progressive Mode FILM
“L1” ----------- Select Progressive Mode L1
“L2” ----------- Select Progressive Mode L2
“OFF” --------- Cancel Progressive scan
“UP” --------------- The same operation as pressing Up key or Left key
“DN” ----------------The same operation as pressing Down key or Right key
Set / cancel Progressive scan
Projector does not save the value set with this command so that it resets when
projector turning into Standby status or ALL is OFF. (The value is held in Suspend
mode.)
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-15-
LV-8320 Expand Serial Command Functional Specifications
8.4.10 CF_NZRED Command
Command
%1
Details
Response
8.4.11
“CF_NZRED_%1”[CR]
“OFF” ------- Cancel Noise Reduction
“L1” --------- Noise Reduction for moving image
“L2” --------- Noise Reduction for still image
“UP” --------------- The same operation as pressing Up key or Left key
“DN” ----------------The same operation as pressing Down key or Right key
Noise Reduction based on frame correlation
Select L1 or L2 depending on motion detection
L2 is more effective in reducing noise than L1, however, L2 can have a blur in
moving image
Projector does not save the value set with this command so that it resets when
projector turning into Standby status or ALL is OFF. (The value is held in Suspend
mode.)
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_IMAGE Command
Command
“CF_IMAGE_%1”[CR]
%1
“DYNAMIC” ---- Presentation(Fixed value to enable projection with a sharp,
powerful picture tone)
“STAND” ------- Standard (Image adjust value is set to factory default)
“REAL” --------- High contrast (Fixed value to display graphic image with natural
tone)
“CINEMA” -------- Cinema (Fixed value to focus on tone reproduction for movie)
“BLACKBOARD” – Blackboard (Fixed value to project image onto green-colored
blackboard)
“COLORBOARD ” – Colorboard(Fixed value to project image onto colored board)
“CUSTOM1” ----- User1 (the value set and stored by a user)
“CUSTOM2” ----- User2 (the value set and stored by a user)
“CUSTOM3” ----- User3 (the value set and stored by a user)
“CUSTOM4” ----- User4 (the value set and stored by a user)
Details
Select Image Mode
Parameter “CUSTOM1” to “CUSTOM4” is the same as “User1” to “User4”
displayed when selecting Image on OSD menu.
The value set by this command is stored in EEPROM and its setting is effective
even after ALL is OFF.
This command is available in normal Power ON status.
Response
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-16-
LV-8320 Expand Serial Command Functional Specifications
8.4.12
CF_COLBOARD Command
Command
%1
“CF_COLBOARD_%1”[CR]
“RED” --------------Select Red
“BLUE” ------------ Select Blue
“YELLOW” ------- Select Yellow
“GREEN” --------- Select Green
Select Color of Colorboard mode.
Image mode is automatically switched to Colorboard mode by receiving this
command.
Details
The value set by this command is stored in EEPROM and its setting is effective
even after ALL is OFF.
This command is available in normal Power ON status.
Response
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.4.13 CF_IMAGEADJ Command
Command
%1
Details
Response
“CF_IMAGEADJ_%1”[CR]
“RST” ------- Reset Image adjustment
“STR1” ----- Store current Image adjustment to User 1
“STR2” ----- Store current Image adjustment to User 2
“STR3” ----- Store current Image adjustment to User 3
“STR4” ----- Store current Image adjustment to User 4
Reset / store Image adjustment.
Parameter “STR1” to “STR4” is the same as “User1” to “User4” displayed when
adjusting Image on OSD menu and selecting “Store”
The value stored to “User 1-4” is saved and its setting is effective even after ALL is
OFF.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-17-
LV-8320 Expand Serial Command Functional Specifications
8.5
PC Adjust Control Command
8.5.1
CF_FSYNC Command
Command
%1
Details
Response
8.5.2
“0000~0031” --------------- Directly select Fine Sync setting value
“UP” -------------------------- Current Fine Sync setting value + 1
“DN” -------------------------- Current Fine Sync setting value - 1
Set Fine Sync value of PC signal
Projector does not save the value set with this command so that it resets when
projector turning into Standby status or ALL is OFF.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_TDOTS Command
Command
“CF_TDOTS_%1”[CR]
%1
“mmmm~nnnn” --- Directly select Total Dots setting value
“mmmm” shows minimum value, it is current Display Dots Horizontal value +
Position value.
“nnnn” shows maximum value, which is not over 140MHz.
“UP” -------------- Current Total Dots setting value + 1
“DN” -------------- Current Total Dots setting value - 1
Details
Set Total Dots of PC signal
Projector does not save the value set with this command so that it resets when
projector turning into Standby status or ALL is OFF.
This command is available in normal Power ON status.
Response
8.5.3
“CF_FSYNC_%1”[CR]
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_CLAMP Command
Command
%1
Details
Response
“CF_CLAMP_%1”[CR]
“mmmm~nnnn” ---- Directly select Clamp setting value
“mmmm” shows minimum value, fixed-value “0001”.
“nnnn” shows maximum value: it depends on input signal.
“UP” ------------------ Current Clamp setting value + 1
“DN” ------------------ Current Clamp setting value – 1
Set Clamp value of PC signal
Projector does not save the value set with this command so that it resets when
projector turning into Standby status or ALL is OFF.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-18-
LV-8320 Expand Serial Command Functional Specifications
8.5.4
CF_H – POS Command
Command
%1
“0000~nnnn” --- Directly select Horizontal Position setting value
“nnnn” shows maximum value, it is current Total Dots value - Display Dots value
“UP” -------------- Current Horizontal Position setting value + 1
“DN” -------------- Current Horizontal Position setting value - 1
Details
Set Horizontal Position value of PC signal.
Projector does not save the value set with this command so that it resets when
projector turning into Standby status or ALL is OFF.
This command is available in normal Power ON status.
Response
8.5.5
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_V – POS Command
Command
“CF_V-POS_%1”[CR]
%1
“0000~nnnn” --- Directly select Vertical Position setting value
“nnnn” shows maximum value, it is current Total Line value - Display Line value
“UP” -------------- Current Vertical Position setting value + 1
“DN” -------------- Current Vertical Position setting value – 1
Details
Set Vertical Position value of PC signal
Projector does not save the value set with this command so that it resets when
projector turning into Standby status or ALL is OFF.
This command is available in normal Power ON status.
Response
8.5.6
“CF_H-POS_%1”[CR]
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_DDOTS Command
Command
%1
Details
Response
“CF_DDOTS_%1”[CR]
“0256”~”nnnn” --- Directly select Display Dots setting value
“nnnn” shows maximum value, it is current Total Dots value - Horizontal
Position value
Even number is available and when odd number is set, it is rounded out.
“UP” -------------- Current Display Dots setting value + 2
“DN” -------------- Current Display Dots setting value – 2
Set Display Dots value of PC signal
Projector does not save the value set with this command so that it resets when
projector turning into Standby status or ALL is OFF.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-19-
LV-8320 Expand Serial Command Functional Specifications
8.5.7
CF_DLINE Command
Command
%1
Details
Response
8.5.8
“0100”~”nnnn” --- Directly select Display Line setting value
“nnnn” shows maximum value, it is current Total Line value – Vertical
Position value
“UP” -------------- Current Display Line setting value + 1
“DN” -------------- Current Display Line setting value – 1
Set Display Line value of PC signal
Projector does not save the value set with this command so that it resets when
projector turning into Standby status or ALL is OFF.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_PCSTORE Command
Command
%1
Details
Response
8.5.9
“CF_DLINE_%1”[CR]
“CF_PCSTORE_%1”[CR]
“MODE1” ---- Store current PC Adjust status to Mode1
“MODE2” ---- Store current PC Adjust status to Mode2
“MODE3” ---- Store current PC Adjust status to Mode3
“MODE4” ---- Store current PC Adjust status to Mode4
“MODE5” ---- Store current PC Adjust status to Mode5
“MODE6” ---- Store current PC Adjust status to Mode6
“MODE7” ---- Store current PC Adjust status to Mode7
“MODE8” ---- Store current PC Adjust status to Mode8
“MODE9” ---- Store current PC Adjust status to Mode9
“MODE10” --- Store current PC Adjust status to Mode10
Store current PC Adjust status (each parameter status such as Total dots) to
Mode1~Mode10. This command operates the same way as storing to
Mode1-Mode10 in PC Adjust MENU.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_PCMODEFREE Command
Command
%1
Details
Response
“CF_PCMODEFREE_%1”[CR]
“MODE1” ---- Set Mode1 to Free status
“MODE2” ---- Set Mode2 to Free status
“MODE3” ---- Set Mode3 to Free status
“MODE4” ---- Set Mode4 to Free status
“MODE5” ---- Set Mode5 to Free status
“MODE6” ---- Set Mode6 to Free status
“MODE7” ---- Set Mode7 to Free status
“MODE8” ---- Set Mode8 to Free status
“MODE9” ---- Set Mode9 to Free status
“MODE10” --- Set Mode10 to Free status
Delete the registered data in Mode1-Mode10 and turns it to Free status.
This command operates the same as turning Mode1-Mode10 to Free in PC Adjust
Menu.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-20-
LV-8320 Expand Serial Command Functional Specifications
8.6
Input Control Command
8.6.1
CF_INPUT Command
Command
%1
Details
Response
8.6.2
“CF_INPUT_%1”[CR]
“CONPUTER1” ----- Select Computer1 Input
“COMPUTER2” ----- Select Computer2 Input
“HDMI” ---------------- Select HDMI Input
“VIDEO” -------------- Select Video Input
“S-VIDEO” -------------- Select S-video Input
“UP” --------------- The same operation as pressing Up key or Left key
“DN” ----------------The same operation as pressing Down key or Right key
Select Input
The same operation as “INPUT” button of the projector and Remote Control.
This command is available in normal Power ON status.
Projector returns “101” by selecting Computer 2 while Monitor out is selected in
Terminal menu.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_SOURCE Command
Command
“CF_SOURCE_%1”[CR]
Input is
Computer 1
“ANALOG” ------- Select Analog Input
“YPBPR” ---------- Select Component Input
“SCART” ----------- Select Scart Input
“UP” ----------------- The same operation as pressing Up key or Left
key
“DN” ------------------The same operation as pressing Down key or
Right key
Input is
Computer 2
“ANALOG” --------- Select Analog Input
”UP”
”DN”
Although no operation is executed,
parameter ”UP” /”DN”
Input is HDMI
“HDMI” ----------- Select HDMI Input
”UP”
”DN”
Although no operation is executed,
parameter ”UP” /”DN”
%1
Input is Video
Input is
S-video
Details
Response
projector
accepts
projector
accepts
“VIDEO” ------------- Select Composite Video Input
”UP”
”DN”
Although no operation is executed, projector
parameter ”UP” /”DN”
“S-VIDEO” ------------- Select S-video Input
”UP”
”DN”
Although no operation is executed,
parameter ”UP” /”DN”
projector
accepts
accepts
Select Source of currently selected Input
When Input specified by %1 is inappropriate for selected Input, the projector
returns “101” and the command is not executed.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-21-
LV-8320 Expand Serial Command Functional Specifications
8.6.3
CF_INPUT1 Command
Command
%1
Details
Response
8.6.4
“CF_INPUT1_%1_”[CR]
“ANALOG” ---------- Select Analog RGB Input
“YPBPR” ------------ Select Component
“SCART” ------------- Select SCART
Select Computer 1 input and source specified by %1 at the same time.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_INPUT2 Command
Command
%1
“CF_INPUT2_%1_”[CR]
“ANALOG” ---------- Select Analog RGB Input
Select Computer 2 input and source specified by %1 at the same time.
This command is available in normal Power ON status.
Details
Projector returns “101” by selecting Computer 2 while Monitor out is selected in
Terminal menu.
Response
8.6.5
%1
Details
Response
“Error Code”[CR]
“CF_INPUT3_%1_”[CR]
“HDMI” ------------------ Select HDMI input
Select HDMI Input. This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_INPUT4 Command
Command
%1
Details
Response
8.6.7
Unacceptable
“000”[CR]
CF_INPUT3 Command
Command
8.6.6
Acceptable
“CF_INPUT4 _%1”[CR]
“VIDEO” ----------------- Select Composite video Input
Select Video input. This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_INPUT5 Command
Command
%1
Details
Response
“CF_INPUT5_%1_”[CR]
“S-VIDEO” ----------------- Select S-video Input
Select S-video input. This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-22-
LV-8320 Expand Serial Command Functional Specifications
8.6.8
CF_INPUT_%1_%2 Command
Command
“CF_INPUT_%1_%2”[CR]
%1
“COMPUTER1” ------ Select Computer1 Input
“COMPUTER2” ------ Select Computer2 Input
“HDMI” ------------------ Select HDMI Input
“VIDEO” ---------------- Select Analog Input
“S-VIDEO” ------------- Select S-video Input
%2
When %1 is COMPUTER1
“ANALOG” ----------Select Analog RGB Input
“YPBPR” ------------- Select Component
“SCART” ------------- Select SCART
When %1 is COMPUTER2
“ANALOG” ---------- Select Analog RGB Input
When %1 is HDMI
“HDMI” ---------- Select HDMI Input
When %1 is VIDEO
“VIDEO” ------------ Select Video Input
When %1 is S-VIDEO
“S-VIDEO” ------------ Select S-video Input
Select Input specified by %1 and also Source specified by %2 at once
This command is available in normal Power ON status.
Details
Projector returns “101” by selecting Computer 2 while Monitor out is selected in
Terminal menu.
Response
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-23-
LV-8320 Expand Serial Command Functional Specifications
8.6.9
CF_SYSTEM Command
Command
“CF_SYSTEM_%1”[CR]
Input is
Computer
%1
“VGA1” ------------- Select VGA1
:
“XGA1” ------------- Select XGA1
:
“WXGA3” ------------ Select WXGA3
“1080I” --------------- Select 1080I
“1035I” --------------- Select 1035I
“720P” ---------------- Select 720P
”575P” ---------------- Select 575P
”480P” ---------------- Select 480P
”575I” ----------------- Select 575I
”480I” ----------------- Select 480I
“MODE1”~ “MODE10”------------- Select Mode 1~Mode 10
Input is HDMI
”D-XGA1” --------------- Select D-XGA1
:
:
”D-WXGA3” ------------- Select D-WXGA3
”D-1080I” ---------------- Select D-1080I
”D-1035I” ---------------- Select D-1035I
”D-720P” ---------------- Select D-720P
”D-575P” ---------------- Select D-575P
”D-480P” ---------------- Select D-480P
Projector returns “101” when no signal is detected.
Input is
Video
“AUTO” -------------------------- Select System “Auto”
“NTSC” -------------------------- Select NTSC
“NTSC443” --------------------- Select NTSC4.43
“PAL” ----------------------------- Select PAL
“SECAM” ----------------------- Select SECAM
“PAL-M” ------------------------- Select PAL-M
“PAL-N” ------------------------- Select PAL-N
“1080I” -------------------------- Select 1080i
“1035I” -------------------------- Select 1035i
“720P” --------------------------- Select 720p
“575P” --------------------------- Select 575p
“480P” --------------------------- Select 480p
“575I” ---------------------------- Select 575i
“480I” ---------------------------- Select 480i
Select System of currently selected Input
When Input specified by %1 is inappropriate for selected Input, the projector
returns “101”[CR] and the command is not executed
This command is available in normal Power ON status.
Details
Response
Note1) “NTSC” / ”NTSC4.43” / ”PAL” / ”SECAM” / ”PAL-M” / ”PAL-N” is available
only when Input is VIDEO / S-VIDEO
Note2) “1080I” / ”1035I” / ”720P” / ”575P” / ”480P” / “575I” / “480I” is available only
when Input is Y / Pb/Cb / Pr/Cr
Note3) D-XGA1/…/D-480P is available only when Input is applicable.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-24-
LV-8320 Expand Serial Command Functional Specifications
8.7
Screen Control Command
8.7.1
CF_SCREEN Command
Command
“CF_SCREEN_%1”[CR]
Input is
Computer
“NORMAL” ---------------------- Select Normal mode
“FULL” --------------------------- Select Full screen mode
“WIDE” -------------------------- Select 16:9 mode
“ZOOM” -------------------------- Select Zoom mode
“TRUE” -------------------------- Select True mode
“CUSTOM” ---------------------- Select Custom mode
“DZOOM_UP” ----------------- Expand image size with Digital Zoom
“DZOOM_DN” ----------------- Reduce image size with Digital Zoom
“UP” ------------------------------ The same operation as pressing Up
key or Left key
“DN” -------------------------------The same operation as pressing
Down key or Right key
Input is
Video
“NORMAL” ---------------------- Select Normal mode
“FULL” --------------------------- Select Full screen mode
“WIDE” -------------------------- Select 16:9 mode
“ZOOM” -------------------------- Select Zoom mode
“NATURAL” ---------------------- Select Natural wide mode
“CUSTOM” ---------------------- Select Custom mode
“UP” ------------------------------ The same operation as pressing Up
key or Left key
“DN” -------------------------------The same operation as pressing
Down key or Right key
%1
AV / PC
Common
Details
“RST” --------------------------- Reset screen adjustment
Select size on screen (in Aspect menu).
When Input specified by %1 is inappropriate for selected Input, the projector
returns “101” [CR] and the command is not executed.
“DZOOM UP” and “DZOOM DN” start effecting from the first command.
This command is available in normal Power ON status.
Note) When Input is computer and AV sorts signals (480i / 575i…etc) are entered,
the signal recognized as Video Input.
Response
8.7.2
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_DZCENT Command
Command
%1
Details
Response
“CF_DZCENT_%1”[CR]
”CENT” ---- Cancel Digital Zoom (CENT: “CENTER”)
Cancel Digital Zoom
When image is expanded or shrunk, reset its value.
This command is available in normal Power ON status and when Input is
Computer.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-25-
LV-8320 Expand Serial Command Functional Specifications
8.7.3
CF_VSCALE Command
Command
%1
Details
Response
8.7.4
“CF_VSCALE_%1”[CR]
“032” --------- +32
“031” --------- +31
:
“002” --------- +2
“001” --------- +1
“000” --------- +0
“-01” ---------- -1
“-02” ---------- -2
:
“-31” ---------- -31
“-32” ---------- -32
“UP” ---------- Vertical Scale setting value + 1
“DN” ---------- Vertical Scale setting value - 1
Set Vertical Scale
This command is available in normal Power ON status.
Note1) When Aspect setting is not in Custom mode, projector changes image
mode into Custom by receiving this command.
Note2) When there is no signal detected, projector returns 101 and the command
does not execute.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_VPOS Command
Command
%1
“CF_VPOS_%1”[CR]
“015” --------- +15
“014” --------- +14
:
“002” --------- +2
“001” --------- +1
“000” --------- +0
“-01” ---------- -1
“-02” ---------- -2
:
“-14” ---------- -14
“-15” ---------- -15
“UP” ---------- Vertical Position setting value + 1
“DN” ---------- Vertical Position setting value – 1
Set Vertical Position
This command is available in normal Power ON status.
Details
Response
Note1) When Aspect setting is not in Custom mode, projector changes image
mode into Custom by receiving this command.
Note2) When there is no signal detected, projector returns 101 and the command
does not execute.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-26-
LV-8320 Expand Serial Command Functional Specifications
8.7.5
CF_HSCALE Command
Command
%1
“CF_HSCALE_%1”[CR]
“032” --------- +32
“031” --------- +31
:
“002” --------- +2
“001” --------- +1
“000” --------- +0
“-01” ---------- -1
“-02” ---------- -2
:
“-31” ---------- -31
“-32” ---------- -32
“UP” ---------- Horizontal Scale setting value + 1
“DN” ---------- Horizontal Scale setting value - 1
Set Horizontal Scale
This command is available in normal Power ON status.
Details
Response
8.7.6
Note1) When Aspect setting is not in Custom mode, projector changes image
mode into Custom by receiving this command.
Note2) When there is no signal detected, projector returns 101 and the command
does not execute.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_HPOS Command
Command
%1
“CF_HPOS_%1”[CR]
“015” --------- +15
“014” --------- +14
:
“002” --------- +2
“001” --------- +1
“000” --------- +0
“-01” ---------- -1
“-02” ---------- -2
:
“-14” ---------- -14
“-15” ---------- -15
“UP” ---------- Horizontal Position setting value + 1
“DN” ---------- Horizontal Position setting value - 1
Set Horizontal Position
This command is available in normal Power ON status.
Details
Response
Note1) When Aspect setting is not in Custom mode, projector changes image
mode into Custom by receiving this command.
Note2) When there is no signal detected, projector returns 101 and the command
does not execute.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-27-
LV-8320 Expand Serial Command Functional Specifications
8.7.7
CF_KEYSTONE Command
Command
%1
Details
“CF_KEYSTONE_%1”[CR]
“UP” ------------- Correct Keystone distortion to reduce upper part of image
“FUP” ----------- Correct Keystone distortion to reduce upper part by 2steps
“DN” ------------- Correct Keystone distortion to reduce lower part of image
“FDN” ----------- Correct Keystone distortion to reduce lower part by 2steps
“RST” ------------ Reset Keystone
Change Keystone distortion correction
This command is available in normal Power ON status.
Acceptable
Response
8.7.8
Unacceptable
“000”[CR]
“Error Code”[CR]
“201”[CR] ----When reaching the Keystone correction limit or
reaching 1 step to correction limit and “FDN”/”FUP”
is received.
(The command is not executed)
CF_KYSTNMODE Command
Command
%1
Details
Response
8.7.9
“CF_KYSTNMODE_%1”[CR]
“STR” --------- Set Keystone store mode to Store
“RST” --------- Set Keystone store mode to Reset
Set Keystone store mode
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_CEIL Command
Command
%1
Details
Response
8.7.10
“CF_CEIL_%1”[CR]
“ON” ------------------------ Set Ceiling to ON
“OFF” ----------------------- Set Ceiling to OFF
Set/Cancel Ceiling setting.
The value set by this command is stored in EEPROM and its setting is effective
even after ALL is OFF
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_REAR Command
Command
%1
Details
Response
“CF_REAR_%1”[CR]
“ON” --------------------------- Set Rear to ON
“OFF” ------------------------- Set Rear to OFF
Set/Cancel Rear setting.
When Rear is ON, image is left/right reversed.
The status set by this command is stored in EEPROM and its setting is effective
after ALL is OFF
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-28-
LV-8320 Expand Serial Command Functional Specifications
8.7.11 CF_SCREENASPECT Command
Command
%1
Details
Response
“CF_SCREENASPECT_%1”[CR]
“43MODE” ・・・・・・・ Select 4:3 mode
“169MODE” ・・・・・・ Select 16:9 mode
“1610MODE” ・・・・・・ Select 16:10 mode
Set Screen aspect mode.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-29-
LV-8320 Expand Serial Command Functional Specifications
8.8
Lamp Command
8.8.1
CF_LAMPMODE Command
Command
%1
Details
Response
8.8.2
“CF_LAMPMODE_%1”[CR]
“AUTO” ------------ Set lamp to Auto status
“NORMAL” ------- Set lamp to Normal mode status
“ECO1” ------------- Set lamp to Eco1 mode status
“ECO2” ------------- Set lamp to Eco2 mode status
“UP” --------------- The same operation as pressing Up key or Left key
“DN” --------------- The same operation as pressing Down key or Right key
Select Lamp Mode
The value set by this command is stored in EEPROM and its setting is effective
even after ALL is OFF.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_ LAMPLIFECONTRL Command
Command
%1
Details
Response
“CF_LAMPLIFECONTRL _%1”[CR]
“MODE1” ------------------------------- Set Lamp life control to Mode 1
“MODE2” ------------------------------- Set Lamp life control to Mode 2
Select Lamp life control function
The value set by this command is stored in EEPROM and its setting is effective
even after ALL is OFF.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-30-
LV-8320 Expand Serial Command Functional Specifications
8.9
Sound Command
8.9.1
CF_VOLUME Command
Command
%1
Details
Response
8.9.2
%1
Details
Response
Control Volume value
The same operation of Volume Up/Down as projector and RC, and directly select
Volume setting value. When setting Volume value, the Sound Mute ON status is
canceled just like RC operation. The value set by this command is stored in
Projector.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
“CF_MUTE_%1”[CR]
“ON” ----------------------------- Set Sound Mute to ON
“OFF” --------------------------- Set Sound Mute to OFF
Control Sound Mute ON/OFF
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_MIC Command
Command
%1
Details
Response
8.9.4
“000-063” -------------------------- Directly select Volume setting value
“UP” --------------------------------- Current Volume setting value +1
“DN” --------------------------------- Current Volume setting value -1
CF_MUTE Command
Command
8.9.3
“CF_VOLUME_%1”[CR]
“CF_MIC_%1”[CR]
“ON” ----------------------------- Set MIC to ON
“OFF” ---------------------------- Set MIC to OFF
Control MIC ON/OFF
This command is available in normal Power ON status.
Acceptable
“000”[CR]
Unacceptable
“Error Code”[CR]
CF_MICGAIN Command
Command
%1
Details
Response
“CF_MICGAIN_%1”[CR]
“000-063” -------------------------- Directly select MIC gain setting value
“UP” --------------------------------- Current MIC GAIN setting value +1
“DN” --------------------------------- Current MIC GAIN setting value -1
Control MIC GAIN value
When setting MIC GAIN value just like operation by menu, the Sound Mute ON
status is canceled. The value set by this command is stored in Projector.
This command is available in normal Power ON status.
Acceptable
“000”[CR]
Unacceptable
“Error Code”[CR]
-31-
LV-8320 Expand Serial Command Functional Specifications
8.9.5
CF_STANDBYMICOUT Command
Command
%1
Details
Response
“CF_STANDBYMICOUT_%1”[CR]
“ON” ----------------------------- Set STANDBY MIC OUT to ON
“OFF” ---------------------------- Set STANDBY MIC OUT to OFF
Control STANDBY MIC OUT ON/OFF
This command is available in normal Power ON status.
Acceptable
“000”[CR]
Unacceptable
“Error Code”[CR]
-32-
LV-8320 Expand Serial Command Functional Specifications
8.10 Setting Command
8.10.1 CF_LANG Command
Command
%1
Details
Response
8.10.2
“CF_LANG_%1”[CR]
“ENG” --------------------------- Select English
“DEU” --------------------------- Select German
“FRA” --------------------------- Select French
“ITA” ----------------------------- Select Italian
“ESP” ---------------------------- Select Spanish
“POR” --------------------------- Select Portuguese
“NED” --------------------------- Select Dutch
“SVE” --------------------------- Select Swedish
“FIN” ---------------------------- Select Finnish
“POL” --------------------------- Select Polish
“HUN” -------------------------- Select Hungarian
“ROM” -------------------------- Select Romanian
“CZE” --------------------------- Select Czech
“RUS” --------------------------- Select Russian
“TUR” -------------------------- Select Turkish
“ARA” --------------------------- Select Arabic
“KAZ” -------------------------- Select Kazakh
“VIE” --------------------------- Select Vietnamese
“CHI” ---------------------------- Select Chinese
“KOR” --------------------------- Select Korean
“JPN” --------------------------- Select Japanese
“THA” -------------------------- Select Thai
Set language for OSD
The language set by this command is stored in EEPROM and its setting is
effective after ALL is OFF.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
CF_MENUPOSITION Command
Command
%1
Details
Response
“CF_MENUPOSITION_%1”[CR]
“SET” ------------------ Move the menu display to next position
Change the menu position
This command is available in normal Power ON status.
The language set by this command is stored in EEPROM and its setting is effective
after ALL is OFF.
Position: center – bottom left-bottom right – top left - top right – center-…
Menu display appears with the first command when menu display is not shown on
the screen
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-33-
LV-8320 Expand Serial Command Functional Specifications
8.10.3 CF_INPUTSEARCH Command
Command
%1
Details
Response
“CF_INPUTSEARCH_%1”[CR]
“OFF” ------------------------- Set Auto input operation to OFF
“ON1” ------------------------- Set Auto input operation to On1
“ON2” ------------------------- Set Auto input operation to On2
Set Auto input operation mode.
The status set by this command is stored in EEPROM and its setting is effective
after ALL is OFF
This command is available in normal Power ON status.
Note) It is unable to set Keystone, Auto PC and Auto input to OFF at once.
e.g. If projector receives Auto input OFF command while Auto PC and Keystone
are OFF, it returns error code “101”.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.4 CF_AUTOSETUPPCADJ Command
Command
%1
Details
Response
“CF_AUTOSETUPPCADJ_%1”[CR]
“ON” ------------------- Set Auto PC function to ON
“OFF” ------------------ Set Auto PC function to OFF
Set/Cancel Auto PC function
This command is available in normal Power ON status.
Note) It is unable to set Keystone, Auto PC and Auto input to OFF at once.
e.g. If projector receives Auto PC OFF command while Keystone and Auto input
are OFF, it returns error code “101”.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.5 CF_AUTOSETUPKEYSTONE Command
Command
%1
Details
Response
“CF_AUTOSETUPKEYSTONE_%1”[CR]
“AUTO” ------------------- Set Auto Keystone function to Auto
“MANUAL” --------------- Set Auto Keystone function to Manual
“OFF” --------------------- Set Auto Keystone function to OFF
Set Keystone function of Auto setup
This command is available in normal Power ON status.
Note) It is unable to set Keystone, Auto PC and Auto input to OFF at once.
e.g. If projector receives Keystone OFF command while Auto PC and Auto input
are OFF, it returns error code “101”.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.6 CF_AUTOSETUP Command
Command
%1
Details
Response
“CF_AUTOSETUP_%1”[CR]
“START” ------------------- Execute Auto Setup
Execute Auto Setup
Note) CF commands does not execute while Auto setup is in process. If the
command is sent during this, projector returns error code “302”
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-34-
LV-8320 Expand Serial Command Functional Specifications
8.10.7
CF_BACKGND Command
Command
%1
Details
Response
“CF_BACKGND_%1” [CR]
“BLUE” -------------------- Select Blue Back
“USER” ------------------- Select User
“BLACK” ------------------ Select Black Back
“UP” ----------------------- The same operation as pressing Up key or Left key
“DN” ----------------------- The same operation as pressing Down key or Right key
Set Screen status for no signal.(Available only in the normal Power ON status)
The status set by this command is stored in EEPROM and the setting remains
even after the power is turned to ALL OFF status.
*When %1=”USER” is received, error code “101” is returned, in the case of
Capture non-practice.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.10.8 CF_DISP Command
Command
%1
Details
Response
“CF_DISP_%1”[CR]
“ON” ----------------------------- Select Display
“OFF” --------------------------- Cancel Display
“CNTDWNOFF” -------------- Count down OFF
“UP” ----------------------- The same operation as pressing Up key or Left key
“DN” ----------------------- The same operation as pressing Down key or Right key
Set / Cancel Display
The value set by this command is stored in EEPROM and its setting is effective
even after ALL is OFF.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-35-
LV-8320 Expand Serial Command Functional Specifications
8.10.9 CF_LOGO Command
Command
“CF_LOGO_%1_%2”[CR]
%1
“0000”-”9999” ----------------- Set LOGO PIN CODE directly
%2
“OFF” ---------------------------- Disable Logo function
“DFLT” --------------------------- Display Default Logo
“USER” -------------------------- Display Captured Logo
“UP” ----------------------- The same operation as pressing Up key or Left key
“DN” ----------------------- The same operation as pressing Down key or Right key
Set / Cancel Logo.
The value set by this command is stored in EEPROM and its setting is effective
even after ALL is OFF. This command is available in normal Power ON status.
%1--- Set LOGO PIN CODE
Details
- When LOGO LOCK is in operation
PIN CODE is correct ------------------ Command is valid (Acceptable)
PIN CODE is incorrect ---------------- Command is invalid (Error Code “102”)
PIN CODE is out of %1 range ------ Command is invalid (Error Code “? “)
-When LOGO LOCK is not in operation
PIN CODE is within %1 range ------ Command is valid
PIN CODE is out of %1 range ------ Command is invalid (Error Code “? “)
Note) Receiving correct LOGO PIN CODE while LOGO LOCK is in operation
enables to change LOGO setting, but it does not release LOGO LOCK. (LOGO
LOCK continues.)
Projector returns Error Code “101” by receiving USER in %2 when capture has not
operated.
Response
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.10 CF_ HDMI SETUP Command
Command
%1
Details
Response
“CF_ HDMI SETUP _%1”[CR]
“NORMAL” -------------------------- Select Normal mode
“ENHANCED” ---------------------- Select Enhanced mode
Select image mode of HDMI setup.
The status set by this command is stored in EEPROM and its setting is effective
after ALL is OFF
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.11 CF_HDMI SOUND Command
Command
%1
Details
Response
“CF_HDMI SOUND_%1”[CR]
“HDMI” ----------------------- Select PCM sound (Digital sound)
“EXTERNAL” ------------- Select External sound input
Select sound mode of HDMI setup.
The status set by this command is stored in EEPROM and its setting is effective
after ALL is OFF
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-36-
LV-8320 Expand Serial Command Functional Specifications
8.10.12 CF_TERMINAL Command
Command
%1
Details
“CF_TERMINAL_%1”[CR]
“COMPUTER” ----------------Set Input mode
“MONITOR” ------------------- Set Monitor Out mode
Set Terminal setup. This command is available in normal Power ON status.
Terminal means Computer 2 in this model.
Acceptable
Response
Unacceptable
“000”[CR]
“Error Code”[CR]
When Input is Computer 2, the projector returns “101” and the
command is not executed.
8.10.13 CF_PIP Command
Command
“CF_PIP_%1”[CR]
%1
“OFF” --------- Set Picture in Picture to OFF
“PINP” -------- Set Picture in Picture to PinP
“PBYP” ------- Set Picture in Picture to PbyP
“UP” ---------- Switch Picture in Picture mode forward(PinP→ PbyP →Off →…)
“DN” ---------- Switch Picture in Picture mode backward(Off → PbyP → PinP →…)
Details
Select Picture in Picture mode.
The status set by this command is stored in EEPROM and its setting is effective
after ALL is OFF. This command is available in normal Power ON status.
Response
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.14 CF_PIPSIZE Command
Command
“CF_PIPSIZE_%1”[CR]
%1
“SMALL” ------------ Select Small
“MIDDLE” ---------- Select Middle
“LARGE” ----------- Select Large
“UP” --- Switch Sub picture size forward (Middle → Large → Small → Middle…)
“DN” --- Switch Power management setting (Small → Large → Middle → Small…)
Details
Select Sub picture size of Picture in Picture.
The status set by this command is stored in EEPROM and its setting is effective
after ALL is OFF. This command is available in normal Power ON status.
Note) Projector returns “101” by receiving this command when Picture in Picture is
Off.
Response
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-37-
LV-8320 Expand Serial Command Functional Specifications
8.10.15 CF_PIPPOSITION Command
Command
“CF_PIPPOSITION_%1”[CR]
%1
“BTMRIGHT” ----------------------- Move Sub picture to Bottom right
“BTMLEFT” ------------------------- Move Sub picture to Bottom left
“TOPRIGHT” ----------------------- Move Sub picture to Top right
“TOPLEFT” ------------------------- Move Sub picture to Top left
“UP” ------------------------------ Switch Sub picture position forward
(Bottom right →Top right →Top left→Bottom left →)
“DN” ------------------------------ Switch Sub picture position backward
(Bottom left →Top left →Top right →Bottom right→)
Details
Select Sub picture position of Picture in Picture.
This command is available in normal Power ON status.
Note) Projector returns “101” by receiving this command when Picture in Picture is
Off.
Response
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.16 CF_P-MANE Command
Command
%1
Details
Response
“CF_P−MANE_%1”[CR]
“OFF” --------------------------------- Set Power management mode to OFF
“READY” ----------------------------- Set Power management mode to Standby
“SHUTDOWN” --------------------- Set Power management mode to Exit mode
“UP” ----------------------- The same operation as pressing Up key or Left key
“DN” ----------------------- The same operation as pressing Down key or Right key
Set/Cancel Power management mode
The status set by this command is stored in EEPROM and its setting is effective
after ALL is OFF
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.17 CF_P-MANETIME Command
Command
%1
Details
Response
“CF_P-MANETIME_%1”[CR]
“01” ~ ”30” ----------------------- Directly select setting time by the minute
“UP” ------------------------------- Plus one minute (01 → 02 → ・・・ → 30 → 01)
“DN” ------------------------------- Minus one minute(30 → 29 → ・・・ → 01 → 30)
Set Power management mode time
The status set by this command is stored in EEPROM and its setting is effective
after ALL is OFF
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-38-
LV-8320 Expand Serial Command Functional Specifications
8.10.18 CF_ON-STA Command
Command
%1
Details
Response
“CF_ON−STA_%1”[CR]
“ON” -------------------------- Set Direct power on active
“OFF” ------------------------- Set Direct power on inactive
“UP” ----------------------- The same operation as pressing Up key or Left key
“DN” ----------------------- The same operation as pressing Down key or Right key
Set/Cancel Direct power on
The status set by this command is stored in EEPROM and its setting is effective
after ALL is OFF
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.19 CF_STANDBYMODE Command
Command
%1
Details
Response
“CF_STANDBYMODE_%1”[CR]
“ECO” ---------------------- Less standby electricity
“NORMAL” ------- -------- Normal standby electricity
Switch Standby Mode setting.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.20 CF_PTIMEMODE Command
Command
%1
Details
Response
“CF_PTIMEMODE_%1”[CR]
“COUNTUP” ---------------- Select Count up
“COUNTDN” ---------------- Select Countdown
Set operation mode of P-timer.
The status set by this command is stored in EEPROM and its setting is effective
after ALL is OFF
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.21 CF_PTIMER Command
Command
“CF_PTOMER_%1”[CR]
%1
“START” ----------------------- Execute P-timer
“STOP” ------------------------ Pause P-timer
“RESTART” ------------------ Restart P-timer
“RST” -------------------------- Reset P-timer
“EXIT” -------------------------- Terminate P-timer function
Details
Control P-timer.
This command is available in normal Power ON status.
Response
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-39-
LV-8320 Expand Serial Command Functional Specifications
8.10.22 CF_PTIME Command
Command
%1
Details
Response
“CF_PTIME_%1”[CR]
“001” ~ “180” -----------Directly specify the timer by minutes.
Set Countdown timer for P-timer function.
The status set by this command is stored in EEPROM and its setting is effective
after ALL is OFF
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.23 CF_CCAPTIONDISP Command
Command
%1
Details
Response
“CF_CCAPTIONDISP_%1”[CR]
“OFF” ------------- Select Off
“CC1” ------------- Select CC1
“CC2” ------------- Select CC2
“CC3” ------------- Select CC3
“CC4” ------------- Select CC4
Select channel of Closed caption.
The status set with this command is stored in EEPROM and its setting is effective
even after ALL is OFF.
This command is available in normal Power ON status.
Closed caption is available under conditions below;
Entered signal is appropriate (Video, NTSC signal of S-video) and System is fixed
to NTSC.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.24 CF_CCAPTIONCOLOR Command
Command
%1
Details
Response
“CF_CCAPTIONCOLOR_%1”[CR]
“COLOR” ------- Select Color
“WHITE” -------- Select White
Select color of Closed caption.
The status set with this command is stored in EEPROM and its setting is effective
even after ALL is OFF.
This command is available in normal Power ON status.
Closed caption is available under conditions below;
Entered signal is appropriate (Video, NTSC signal of S-video) and System is fixed
to NTSC.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-40-
LV-8320 Expand Serial Command Functional Specifications
8.10.25 CF_RCODE Command
Command
%1
Details
Response
“CF_RCODE_%1”[CR]
"001” --------------------------- Select Code1
"002” --------------------------- Select Code2
“UP” --------------- The same operation as pressing Up key or Left key
“DN” --------------- The same operation as pressing Down key or Right key
Select Code of Remote Control
The status set by this command is stored in EEPROM and its setting is effective
after ALL is OFF
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.26 CF_KEYDIS Command
Command
%1
Details
Response
“CF_KEYDIS_%1”[CR]
“NONE” ----------------------- RC & Projector keys are valid (All are valid)
“RC” ---------------------------- RC keys are invalid
“KEY” -------------------------- Projector keys are invalid
Disable RC/Projector keys
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.27 CF_PJPINCODE Command
Command
%1
“CF_PJPINCODE_%1”[CR]
“0000” – “9999” ---------Set PJ PIN CODE directly
Set PJ PIN CODE to release PJ LOCK.
PIN CODE cannot be changed by this command.
-When PJ LOCK is in operation
PIN CODE is correct ------------------------- Command is valid (Acceptable)
PIN CODE is incorrect ----------------------- Command is invalid(Error Code”102”)
PIN CODE is out of %1 range ------------- Command is invalid (Error Code “? “)
Details
-When PJ LOCK is not in operation
PIN CODE is within %1 range ---------------- Command is valid (Acceptable)
PIN CODE is out of %1 range ---------------- Command is invalid (Error Code “? “)
This command is valid during a dialog “PJ PIN CODE” is displayed after Power On
and Count down.
Also when PJ LOCK setting is “On1”, it is necessary to transmit this command
every time lamp turns on.
Response
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-41-
LV-8320 Expand Serial Command Functional Specifications
8.10.28 CF_FANMODE Command
Command
%1
Details
Response
“CF_FANMODE_%1”[CR]
“L1” ---------------------------- Set Fan Mode to L1
“L2” ---------------------------- Set Fan Mode to L2
Switch Fan Mode
When L1 is selected, fan noise after POWER OFF is louder.
When L2 is selected, fan noise after POWER OFF becomes quiet; however, fan
rotates longer than L1.
The status set by this command is stored in EEPROM and its setting is effective
even after ALL is OFF.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.29 CF_FANCONTROL Command
Command
%1
Details
Response
“CF_FANCONTROL_%1”[CR]
“OFF” ---------------------------- Set Fan control to Off
“ON1” ---------------------------- Set Fan control to On1
“ON2” ---------------------------- Set Fan control to On2
Set Fan control setting.
The status set by this command is stored in EEPROM and its setting is effective
even after ALL is OFF.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.30 CF_DELAYCTRL Command
Command
%1
Details
Response
“CF_DELAYCTRL_%1”[CR]
“ON” --------------------------- Set Video delay control On
“OFF” -------------------------- Set Video delay control Off
Set Video delay control.
The status set by this command is stored in EEPROM and its setting is effective
even after ALL is OFF. This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.31 CF_FILTIMER Command
Command
%1
Details
Response
“CF_FILTIMER_%1”[CR]
“1000” -------------------- Set 1000 hours
“2000” -------------------- Set 2000 hours
“3000” -------------------- Set 3000 hours
“4000” -------------------- Set 4000 hours
“5000” -------------------- Set 5000 hours
“6000” -------------------- Set 6000 hours
“OFF” ------------------- No warning display
“UP” --------------- The same operation as pressing Up key or Left key
“DN” --------------- The same operation as pressing Down key or Right key
Set timer of Filter replacement /clean-up warning display.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-42-
LV-8320 Expand Serial Command Functional Specifications
8.10.32 CF_FILH Command
Command
%1
Details
Response
“CF_FILH_%1”[CR]
“RST” ---------------Reset Filter used time
Reset filter used time
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.33 CF_TTLPWRSAVE Command
Command
%1
Details
Response
“CF_TTLPWRSAVE _%1”[CR]
“RST” ---------------Reset Total power savings
Reset the value of Total power savings
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.10.34 CF_FDEFAULT Command
Command
%1
Details
Response
“CF_FDEFAULT_%1”[CR]
“RST”
Set the value to Factory Default
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-43-
LV-8320 Expand Serial Command Functional Specifications
8.11 Other Command
8.11.1 CF_KEYENU Command
Command
%1
Details
Response
“CF_KEYENU_%1”[CR]
“RIGHT” ------------------------- Shift Pointer on OSD Menu to right
“LEFT” --------------------------- Shift Pointer on OSD Menu to left
“UP” ------------------------------ Shift Pointer on OSD Menu to right
“DN” ------------------------------ Shift Pointer on OSD Menu to right
“SELECT” ----------------------- Behave the same as OK key
“AUTOPC” ---------------------- Execute Auto PC
This command behave the same as corresponding keys of Remote Control /
Projector
Auto PC keeps operating even though projector receives this command again
while Auto PC is in process.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.11.2 CF_MENU Command
Command
%1
Details
Response
“CF_MENU_%1”[CR]
“ON” ----------------------------- Display OSD Menu
“OFF” --------------------------- Cancel OSD menu
Display / Cancel On Screen Display Menu
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.11.3 CF_POWER Command
Command
“CF_POWER_%1”[CR]
“ON” ------------Power ON projector
“OFF” ---------- Power OFF Projector
Note1) Countdown can be terminated by sending this command.
%1
Note2) Projector returns error code due to unable of command execution depends
on its condition.
Note3) Although projector returns “OK”, operation may not be proceeding properly.
(e.g. After returning “000” for Power ON command, projector gets abnormal
temperature.) Use Status read command to get projector states.
Details
Response
Power ON / OFF projector.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-44-
LV-8320 Expand Serial Command Functional Specifications
8.11.4 CF_FREEZE Command
Command
%1
Details
Response
“CF_FREEZE_%1”[CR]
“ON” ------------------------ Set Freeze to ON
“OFF” ----------------------- Set Freeze to OFF
“UP” --------------- The same operation as pressing Up key or Left key
“DN” --------------- The same operation as pressing Down key or Right key
Set/Cancel Freeze setting.
Although projector returns “000”, receiving another Freeze command does not
release Freeze operation.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
8.11.5 CF_VMUTE Command
Command
%1
Details
Response
“CF_VMUTE_%1”[CR]
“ON” --------------------------- Set Blank ON
“OFF” ------------------------- Set Blank OFF
“UP” --------------- The same operation as pressing Up key or Left key
“DN” --------------- The same operation as pressing Down key or Right key
Set/Cancel Blank setting.
This command is available in normal Power ON status.
Acceptable
Unacceptable
“000”[CR]
“Error Code”[CR]
-45-
LV-8320 Expand Serial Command Functional Specifications
9.Status Read Command
9.1
Format
1)
PC issues commands in format as below:
“CR_Command” [CR]
Command : Character Line
2)
When projector receives the appropriate command, it returns a character line as the
required data
“000_”%1 [CR]
%1: Required Data (Character Line. See [Basic Status Read Command Table])
3)
9.2
When the received data cannot be decoded, the projector returns “?”[CR]
Transfer Example
Get total dots of projector by Expand Commands
PC → PJ: “CR_TDOTS” [CR]
PC ← PJ: “000_1344” [CR]
9.3
Operation Condition
1) Basically Status Read Commands should be always operated.
2) When Eco mode is selected in Standby mode of Setting menu and projector is in Standby,
Status Read Commands are invalid.
9.4
Image Status Read Command
9.4.1
CR_BRIGHT Command
Command
Details
“CR_BRIGHT”[CR]
Get Brightness value of user control
Acceptable
Response
%a
Unacceptable
9.4.2
“000_%a”[CR]
“000”~“063”
“Error Code”[CR]
CR_CONT Command
Command
Details
“CR_CONT”[CR]
Get Contrast value of user control
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“000”~“063”
“Error Code”[CR]
-46-
LV-8320 Expand Serial Command Functional Specifications
9.4.3
CR_COLOR Command
Command
Details
“CR_COLOR”[CR]
Get Color value of user control
Acceptable
Response
%a
Unacceptable
9.4.4
Details
Response
Get Tint value of user control
%a
Unacceptable
Details
“000”~“063”
“Error Code”[CR]
“CR_SHARP”[CR]
Get Sharpness value of user control
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“000”~“015”
“Error Code”[CR]
CR_GAMMA Command
Command
Details
"CR_GAMMA”[CR]
Get Gamma value of user control
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“000”~“015”
“Error Code”[CR]
CR_WBAL – R Command
Command
Details
"CR_WBAL-R”[CR]
Get White Balance Red value of user control
Acceptable
Response
%a
Unacceptable
9.4.8
“000_%a”[CR]
CR_SHARP Command
Command
9.4.7
“Error Code”[CR]
“CR_TINT”[CR]
Acceptable
9.4.6
“000”~“063”
CR_TINT Command
Command
9.4.5
“000_%a”[CR]
“000_%a”[CR]
“000”~“063”
“Error Code”[CR]
CR_WBAL – G Command
Command
Details
"CR_WBAL-G”[CR]
Get White Balance Green value of user control
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“000”~“063”
“Error Code”[CR]
-47-
LV-8320 Expand Serial Command Functional Specifications
9.4.9
CR_WBAL – B Command
Command
Details
"CR_WBAL-B”[CR]
Get White Balance Blue value of user control
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“000”~“063”
“Error Code”[CR]
9.4.10 CR_COLTEMP Command
Command
Details
"CR_COLTEMP”[CR]
Get Color Temp. setting value
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“000” ------------------------------ Xlow
“001” ------------------------------ Low
“002” ------------------------------ Mid
“003” ------------------------------ High
“BLACK” -------------------- Blackboard(Green) mode selected
“COLOR” ------------------- Colorboard selected
“BLANK” -------------------- White Balance has been changed
“Error Code”[CR]
9.4.11 CR_NZRED Command
Command
Details
“CR_NZRED”[CR]
Get setting status of Noise Reduction
Acceptable
Response
%1
Unacceptable
9.4.12
“000_%1”[CR]
“L1” -------- Noise Reduction for moving image
“L2” -------- Noise Reduction for still image
“OFF” ----- Noise Reduction is OFF
“Error Code”[CR]
CR_PROGV Command
Command
Details
“CR_PROGV”[CR]
Get setting status of Progressive scan
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“L1” ----------------- Progressive Mode L1 is selected
“L2” ----------------- Progressive Mode L2 is selected
“FILM” -------------- Progressive Model FILM is selected
“OFF” --------------- Progressive scan is disabled
“Error Code”[CR]
-48-
LV-8320 Expand Serial Command Functional Specifications
9.4.13 CR_IMAGE Command
Command
Details
“CR_IMAGE”[CR]
Get image setting status
Required data “CUSTOM1” to “CUSTOM4” is the same as “Image1” to “Image4”
displayed when selecting IMAGE on OSD menu
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“DYNAMIC” --------------------------------------- Presentation
“STAND” ------------------------------------------- Standard
“REAL” --------------------------------------------- High contrast
“CINEMA” ----------------------------------------- Cinema
“BLACKBOARD” -------------------------------- Blackboard
“COLORBOARD” -------------------------------- Colorboard
“CUSTOM1”~”CUSTOM4” -------------------- User1~4
“Error Code”[CR] ---- When the command is invalid due to
condition such as Input source
9.4.14 CR_IMGGMD Command
Command
Details
"CR_IMGGMD”[CR]
Get Image Gamma setting status
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“DYN” ------------ Presentation
“STD” ------------ Standard
“REL” ------------ High contrast
“CNM” ----------- Cinema
“BKB” ------------ Blackboard
“CLB” ------------ Colorboard
“Error Code”[CR]
9.4.15 CR_COLBOARD Command
Command
Details
“CR_COLBOARD_%1”[CR]
Get Colorboard setting status
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“RED” -------------- Select Red
“BLUE” ------------ Select Blue
“YELLOW” ------- Select Yellow
“GREEN” --------- Select Green
“Error Code”[CR]
-49-
LV-8320 Expand Serial Command Functional Specifications
9.5
PC Adjust Status Read Command
9.5.1
CR_FSYNC Command
Command
Details
Response
"CR_FSYNC”[CR]
Get Fine Sync value
Acceptable
“000_%a”[CR]
%a
“0000”~“0031”
Unacceptable
9.5.2
CR_TDOTS Command
Command
Details
“CR_TDOTS”[CR]
Get Total Dots value
Acceptable
Response
%a
Unacceptable
9.5.3
Details
“nnnn”~“mmmm”
(nnnn = Display Dots + Horizontal Position)
(mmmm= Maximum value depends on input signal)
“Error Code”[CR]
“CR_CLAMP”[CR]
Get Clamp value
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“0001”~“nnnn”
(“nnnn” depends on input signal)
“Error Code”[CR]
CR_H – POS Command
Command
Details
“CR_H - POS”[CR]
Get Horizontal Position value
Acceptable
Response
%a
Unacceptable
9.5.5
“000_%a”[CR]
CR_CLAMP Command
Command
9.5.4
“Error Code”[CR]
“000_%a”[CR]
“0000”~“nnnn”
(nnnn = Total Dots - Display Dots)
“Error Code”[CR]
CR_V – POS Command
Command
Details
“CR_V - POS”[CR]
Get Vertical Position value
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“0000”~“nnnn”
(nnnn = Total Line - Display Line)
“Error Code”[CR]
-50-
LV-8320 Expand Serial Command Functional Specifications
9.5.6
CR_DDOTS Command
Command
Details
“CR_DDOTS”[CR]
Get Display Dots value
Acceptable
Response
%a
Unacceptable
9.5.7
“0256”~“nnnn”
(nnnn = Total Dots – Horizontal Position value)
“Error Code”[CR]
CR_DLINE Command
Command
Details
“CR_DLINE”[CR]
Get Display Line value
Acceptable
Response
%a
Unacceptable
9.5.8
“000_%a”[CR]
“000_%a”[CR]
“0100”~“nnnn”
(nnnn = Total Line – Vertical Position value)
“Error Code”[CR]
CR_PCSTORE Command
Command
Details
“CR_PCSTORE”[CR]
Get Free/Stored status of MODE1 - MODE5 for PC Adjust.
Each data consists of 10 bytes. Each byte indicates
MODE1~MODE10 respectively. (F:Free S:Stored)
Acceptable
Response
%a
Unacceptable
the
status
“000_%a”[CR]
“FFFFFFFFFF” ----------- All Free
“SFFFFFFFFF” ----------- MODE1 is Stored, others are Free
:
“FFFFFFFFFS” ----------- MODE5 is Stored, others are Free
“SSSSSSSSSS” ---------- All Stored
“Error Code”[CR]
-51-
of
LV-8320 Expand Serial Command Functional Specifications
9.6
Video Status Read Command
9.6.1
CR_SERSYS Command
Command
Details
“CR_SERSYS”[CR]
Get currently selected signal
Returns auto-detected signal in Auto mode
Only available for Video input. (N/A when Input is computer)
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“1080I60” -------------- 1080i 60Hz
“1080I50” -------------- 1080i 50Hz
“1035I”. ---------------- 1035i
“720P” ------------------ 720p
“575P” ------------------ 575p
“480P” ------------------ 480p
“575I” ------------- 575i (includes Composite signal such as PAL)
“480I” ------------- 480i (includes Composite signal such as NTSC)
“NO_SIGNAL” --------------- There is no signal
“Error Code”[CR]
-52-
LV-8320 Expand Serial Command Functional Specifications
9.7
Input Status Read Command
9.7.1
CR_INPUT Command
Command
Details
“CR_INPUT”[CR]
Get selected INPUT No.
Acceptable
Response
Request data
Unacceptable
9.7.2
“CR_SOURCE”[CR]
Details
Get selected Source
“000_%1”[CR]
Request data
“ANALOG” ---------- Analog (RGB) Input is selected
“SCART” ------------- SCART is selected
“HDMI” ---------------- HDMI Input is selected
“VIDEO” -------------- Video Input is selected
“S-VIDEO” ----------- S-Video Input is selected
“YPBPR” ------------- Component Input is selected
Unacceptable
“Error Code”[CR]
CR_SRCINP1 Command
Command
Details
"CR_SRCINP1” [CR]
Get selected source of Input 1_CMP1
Acceptable
Response
“000_%1”[CR]
Request data
“ANALOG” ---------- Analog RGB Input is selected
“YPBPR” ----------- YPBPR Input is selected
“SCART” ----------- Scart Input is selected
Unacceptable
“Error Code”[CR]
CR_SRCINP2 Command
Command
Details
"CR_SRCINP2” [CR]
Get selected source of Input 2_CMP2
Acceptable
Response
9.7.5
“Error Code”[CR]
Command
Response
9.7.4
“1”-”5”
CR_SOURCE Command
Acceptable
9.7.3
“000_%1”[CR]
“000_%1”[CR]
Request data
“ANALOG” --------- Analog RGB Input is selected
“OUT” ---------------- Monitor out is selected
Unacceptable
“Error Code”[CR]
CR_SRCINP3 Command
Command
Details
"CR_SRCINP3” [CR]
Get selected source of Input 3_ HDMI
Acceptable
Response
“000_%1”[CR]
Request data
“HDMI” -------------- HDMI is selected
Unacceptable
“Error Code”[CR]
-53-
LV-8320 Expand Serial Command Functional Specifications
9.7.6
CR_SRCINP4 Command
Command
Details
"CR_SRCINP4” [CR]
Get selected source of Input 4_Video
Acceptable
Response
9.7.7
“000_%1”[CR]
Request data
“VIDEO” ------------- Composite Video Input is selected
Unacceptable
“Error Code”[CR]
CR_SRCINP5 Command
Command
Details
"CR_SRCINP5” [CR]
Get selected source of Input 5_S-video
Acceptable
Response
“000_%1”[CR]
Request data
“S-VIDEO” ------------- S-video Input is selected
Unacceptable
“Error Code”[CR]
-54-
LV-8320 Expand Serial Command Functional Specifications
9.7.8
CR_SYSTEM Command
Command
“CR_SYSTEM”[CR]
Details
Get selected System
Acceptable
Response
%1
“000_%1”[CR]
Input is
PC Analog
“VGA1” -------------- VGA1 is selected
“VGA2” -------------- VGA2 is selected
:
“XGA1”-------------- XGA1 is selected
:
“WXGA3” --------- WXGA3 is selected
“1080i” ------------ 1080i is selected
“1035i” ------------ 1035i is selected
“720p” ------------- 720p is selected
“575p” ------------- 575p is selected
“480p” ------------- 480p is selected
“575i” -------------- 575i is selected
“480i” -------------- 480i is selected
“MODE1” ------- Mode1 is selected
:
“MODE10” -------------- Mode10 is selected
When there is no signal, projector returns error code”101”
[CR]
Input is
HDMI
“D−XGA1” ------------- D-XGA1 is selected
:
“D−WXGA3” ---------- D-WXGA3 is selected
“D−1080I” ------------- D-1080i is selected
“D−1035I” ------------- D-1035i is selected
“D−720P” ------------- D-720p is selected
“D−575P” ------------- D-575p is selected
“D−480P” ------------- D-480p is selected
When there is no signal, projector returns error code”101”
[CR]
Input is
Y,Pb/Cb,Pr
/Cr
“AUTO” ----------- Auto is selected
“1080i” ------------1080i is selected
“1035i” ------------ 1035i is selected
“720p” ------------- 720p is selected
“575p” ------------- 575p is selected
“480p” ------------- 480p is selected
“575i” -------------- 575i is selected
“480i” -------------- 480i is selected
Projector returns selected System status regardless of the
signal input.
Input is
Video,
S-Video
“AUTO” --------------- Auto is selected
“NTSC” --------------- NTSC is selected
“NTSC443” ---------- NTSC4.43 is selected
“PAL” ------------------ PAL is selected
“SECAM” ------------- SECAM is selected
“PAL−M” ------------- PAL-M is selected
“PAL−N” ------------- AL-N is selected
Projector returns selected System status regardless of the
signal input.
Unacceptable
““Error Code”[CR]
-55-
LV-8320 Expand Serial Command Functional Specifications
9.7.9
CR_SYSLIST Command
Command
Details
“CR_SYSLIST”[CR]
Get selectable System titles
Acceptable
“000_%1_%2_..._%x” [CR]
- When Input is PC-Analog
“XGA1” ------------ XGA1is selectable
“1080I ” ----------- 1080i is selectable
Projector does not return Auto,Mode1-10
When there is no signal, it returns Error Code “101”
- When Input is HDMI
“D-XGA” ---------- D- XGA1is selectable
“D-720P” --------- D-720P is selectable
When there is no signal, projector returns Error Code “101”
Response
%1
-When Input is Y,Pb/Cb,Pr/Cr
Returns all the System titles on Menu including Auto
“AUTO” ------------ Auto is selectable
“1080I” ------------ 1080i is selectable
“1035I” ------------ 1035i is selectable
:
:
“575I” ------------ 575i is selectable
“480I” ------------ 480i is selectable
Projector does not return Error Code “101” even if there is no
signal.
-When Input is Video, S-Video
Returns all the System titles on Menu including Auto
“AUTO” ---------Auto is selectable
“PAL” ------------ PAL is selectable
“SECAM” ------ SECAM is selectable
:
:
“PAL-N” --------- PAL-N is selectable
Projector does not return Error Code “101” even if there is no
signal.
Unacceptable
““Error Code”[CR]
9.7.10 CR_MODELIST Command
Command
Details
“CR_MODELIST”[CR]
Get selectable Mode titles
Acceptable
Response
%1
%2
:
%x
Unacceptable
“000_%1_%2_..._%x” [CR]
Returns Error code “101” when Input is other than PC-Analog
Returns Error code “101” when Input is PC-Analog but no signal
When Input is PC-Analog and signal is found, returns selectable
Mode among Mode1 – 10
“MODE1”
:
:
“MODE10
“Error Code”[CR]
-56-
LV-8320 Expand Serial Command Functional Specifications
9.8
Screen Status Read Command
9.8.1
CR_SCREEN Command
Command
Details
“CR_SCREEN”[CR]
Get selected on-screen Aspect mode (screen size)
Acceptable
Response
Input
is
PC
“NORMAL” --------------- Normal mode is selected
“FULL” --------------------- Full mode is selected
“WIDE” -------------------- 16:9 mode is selected
“ZOOM” -------------------- Zoom mode is selected
“TRUE” -------------------- True mode is selected
When the screen is set to D.Zoom, projector returns the previous
status (NORMAL )
“CUSTOM” ---------------- Custom mode is selected
Input
is
Video
“NORMAL” --------------- Normal mode is selected
“FULL” --------------------- Full mode is selected
“WIDE” -------------------- 16:9 mode is selected
“ZOOM” -------------------- Zoom mode is selected
“NATURAL” --------------- Natural wide is selected
“CUSTOM” --------------- Custom mode is selected
%a
Unacceptable
9.8.2
“000_%a”[CR]
“Error Code”[CR]
CR_VSCALE Command
Command
Details
Response
“CR_VSCALE”[CR]
Get setting status of Vertical Scale Store Mode
Acceptable
“000_%1[CR]
%1
“-32” ~ “032”
Unacceptable
9.8.3
CR_VPOS Command
Command
Details
“CR_VPOS”[CR]
Get setting status of Vertical Position Store Mode
Acceptable
Response
%1
Unacceptable
9.8.4
“Error Code”[CR]
“000_%1”[CR]
“-15” ~ “015”
“Error Code”[CR]
CR_HSCALE Command
Command
Details
“CR_HSCALE”[CR]
Get setting status of Horizontal Scale Store Mode
Acceptable
Response
%1
Unacceptable
“000_%1”[CR]
“-32” ~ “032”
“Error Code”[CR]
-57-
LV-8320 Expand Serial Command Functional Specifications
9.8.5
CR_HPOS Command
Command
Details
“CR_HPOS”[CR]
Get setting status of Horizontal Position Store Mode
Acceptable
Response
%1
“000_%1”[CR]
“-15” ~ “015”
Unacceptable
9.8.6
“Error Code”[CR]
CR_ KYSTNMODE Command
Command
Details
“CR_KYSTNMODE”[CR]
Get setting status of Keystone Store Mode
Acceptable
Response
%a
“000_%a”[CR]
“STR” ---------------------- Store mode is “Store”
“RST” ---------------------- Store mode is “Reset”
Unacceptable
9.8.7
CR_CEIL Command
Command
Details
“CR_CEIL” [CR]
Get setting status of Ceiling
Acceptable
Response
%1
Unacceptable
9.8.8
“000_%1”[CR]
“ON” ------------------------------ Ceiling is ON
“OFF” ----------------------------- Ceiling is OFF
“Error Code” [CR]
CR_REAR Command
Command
Details
“CR_REAR” [CR]
Get setting status of Rear
Acceptable
Response
%1
Unacceptable
9.8.9
“Error Code”[CR]
“000_%1”[CR]
“ON” ------------------------------ Rear is ON
“OFF” ----------------------------- Rear is OFF
“Error Code” [CR]
CR_SCREENASPECT Command
Command
“CR_SCREENASPECT”[CR]
Details
Get status of Screen aspect
Acceptable
Response
%1
Unacceptable
“000_%1”[CR]
“43MODE” ・・・・・・・ Select 4:3 mode
“169MODE” ・・・・・・ Select 16:9 mode
“1610MODE” ・・・・・・ Select 16:10 mode
“Error Code” [CR]
-58-
LV-8320 Expand Serial Command Functional Specifications
9.9
Lamp Status Read Command
9.9.1
CR_LAMPREPL Command
Command
Details
“CR_LAMPREPL”[CR]
Get information of Lamp Replacement time
Acceptable
“000_%1”[CR]
“1Y” -------------------------- Over lamp replacement time
“1N” -------------------------- Within lamp replacement time
Response
%1
Unacceptable
9.9.2
Details
“CR_LAMPH”[CR]
Get total running time of lamp by hour (h)
*Actual running time, not corresponding value
Acceptable
Response
“000_%1”[CR]
%1
“00000”~“99999”
Unacceptable
“Error Code”[CR]
CR_LAMPCORRESPH Command
Command
Details
“CR_LAMPCORRESPH”[CR]
Get total running time of lamp by hour (h)
* Corresponding value, not actual running time
Acceptable
Response
9.9.4
“Error Code”[CR]
CR_LAMPH Command
Command
9.9.3
“1” means the number of lamps.
(1 lamp model→ “1”)
“Y”/”N” means if it has reached its replacement time or not.
e.g. “1Y” -----------projector is 1 lamp model and Lamp is over its
replacement time
“000_%1”[CR]
%1
“00000”~“99999”
Unacceptable
“Error Code”[CR]
CR_LAMPMODE Command
Command
Details
“CR_LAMPMODE”[CR]
Get setting status of Lamp Mode
Acceptable
Response
%1
Unacceptable
“000_%1”[CR]
“AUTO” -------------------- Lamp Mode is Auto
“NORMAL” -------------- Lamp Mode is Normal
“ECO1” --------------------- Lamp Mode is Eco1
“ECO2” --------------------- Lamp Mode is Eco2
“Error Code”[CR]
-59-
LV-8320 Expand Serial Command Functional Specifications
9.9.5
CR_LAMPMSTS Command
Command
Details
“CR_LAMPSTS”[CR]
Get Lighting status of lamp
Acceptable
“000_%1”[CR]
“n****” A number of * should be among 1-4.
First character shows how many lamps are incorporated in
projector. (1,2 or 4 )
Response
%1
Unacceptable
9.9.6
Details
“CR_PROJH”[CR]
Get total running time of Projector by hour (h)
Acceptable
Response
%1
Unacceptable
“000_%1”[CR]
“0000000”~“0099999”
“Error Code”[CR]
CR_HMLAMP Command
Command
Details
“CR_HMLAMP”[CR]
Get lamp number.
Acceptable
Response
%1
Unacceptable
9.9.8
“Error Code”[CR]
CR_PROJH Command
Command
9.9.7
Second character shows following status in order of lamp number.
“I”
Lamp is ON
“O” Lamp is OFF
“X” Lamp failure
e.g.
“1I” ・・・・・・・ 1 lamp model and Lamp is ON
“2IO・・・・・・・ 2 lamps model and No.1 Lamp is ON and No.2Lamp
is OFF
“4IOXI” ・・・・ 4 lamps model and No.1,No.4 lamps are ON. No.2
lamp is OFF and No.3 model is failed.
“000_%1”[CR]
“001”
“Error Code” [CR]
CR_ LAMPLIFECONTRL Command
Command
Details
“CR_LAMPLIFECONTRL” [CR]
Get setting status of Lamp life control
Acceptable
Response
%1
Unacceptable
“000_%1”[CR]
“MODE1” --------------- Lamp life control is Mode1 status
“MODE2” --------------- Lamp life control is Mode2 status
“Error Code” [CR]
-60-
LV-8320 Expand Serial Command Functional Specifications
9.10 Sound Status Read Command
9.10.1 CR_VOLUME Command
Command
Details
“CR_VOLUME”[CR]
Get Volume value of user control
Acceptable
Response
%a
“000_%a”[CR]
“000”~“063”
Unacceptable
“Error Code” [CR]
9.10.2 CR_MUTE Command
Command
Details
“CR_MUTE”[CR]
Get sound mute setting status
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“ON” -------------------- Sound Mute is ON
“OFF” ------------------- Sound Mute is OFF
“Error Code” [CR]
9.10.3 CR_MIC Command
Command
“CR_MIC”[CR]
Details
Get setting status of MIC
Acceptable
Response
%1
Unacceptable
“000_%1”[CR]
“ON” -------------------- MIC is ON
“OFF” ------------------- MIC is OFF
“Error Code” [CR]
9.10.4 CR_MICGAIN Command
Command
“CR_MICGAIN”[CR]
Details
Get MIC GAIN value of user control
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“000” ~ “063”
“Error Code” [CR]
9.10.5 CR_STANDBYMICOUT Command
Command
“CR_STANDBYMICOUT”[CR]
Details
Get setting status of STANDBY MIC OUT
Acceptable
Response
%1
Unacceptable
“000_%1”[CR]
“ON” -------------------- STANDBY MIC OUT is ON
“OFF” ------------------- STANDBY MIC OUT is OFF
“Error Code” [CR]
-61-
LV-8320 Expand Serial Command Functional Specifications
9.11 Setting Status Read Command
9.11.1 CR_LANG Command
Command
Details
“CR_LANG”[CR]
Get selected language
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“ENG” -------------------------- English is selected
“DEU” -------------------------- German is selected
“FRA” -------------------------- French is selected
“ITA” --------------------------- Italian is selected
“ESP” -------------------------- Spanish is selected
“POR” -------------------------- Portuguese is selected
“NED” -------------------------- Dutch is selected
“SVE” -------------------------- Swedish is selected
“FIN” ---------------------------- Finnish is selected
“POL” --------------------------- Polish is selected
“HUN” -------------------------- Hungarian is selected
“ROM” -------------------------- Romanian is selected
“CZE” ---------------------------- Czech is selected
“RUS” -------------------------- Russian is selected
“TUR” --------------------------- Turkish is selected
“ARA” --------------------------- Arabic is select
“KAZ” --------------------------- Kazakh is selected.
“VIE” ---------------------------- Vietnamese is selected
“CHI” -------------------------- Chinese is selected
“KOR” -------------------------- Korean is selected
“JPN” -------------------------- Japanese is selected
“THA” --------------------------- Thai is selected
“Error Code”[CR]
9.11.2 CR_INPUTSEARCH Command
Command
Details
“CR_INPUTSEARCH”[CR]
Get setting status of Auto input
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“OFF” --------------------- Auto input is OFF
“ON1” --------------------- Auto input is On1
“ON2” --------------------- Auto input is On2
“Error Code”[CR]
9.11.3 CR_AUTOSETUPPCADJ Command
Command
Details
“CR_AUTOSETUPPCADJ” [CR]
Get Auto PC setting status in Auto setup
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“ON” ------------------ Auto PC in Auto setup is ON
“OFF” ----------------- Auto PC in Auto setup is OFF
“Error Code”[CR]
-62-
LV-8320 Expand Serial Command Functional Specifications
9.11.4 CR_AUTOSETUPKEYSTONE Command
Command
Details
“CR_AUTOSETUPKEYSTONE” [CR]
Get Keystone setting status in Auto setup
Acceptable
Response
%a
“000_%a”[CR]
“AUTO” -------------- Auto Keystone is Auto
“MANUAL” ---------- Auto Keystone is Manual
“OFF” ---------------- Auto Keystone is OFF
Unacceptable
“Error Code”[CR]
9.11.5 CR_BACKGND Command
Command
Details
“CR_BACKGND” [CR]
Get setting status of Screen for no signal
Acceptable
Response
“000_%1” [CR]
“BLUE” -------------------------------- Blue Back is selected
“USER” ------------------------------- User is selected
“BLACK” ------------------------------ Black Back is selected
%1
Unacceptable
“Error Code” [CR]
9.11.6 CR_DISP Command
Command
Details
“CR_DISP”[CR]
Get setting status of Display
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“ON” -------------------------- Display is ON
“OFF” ------------------------ Display is OFF
“CNTDWNOFF” ---------- Countdown OFF
“Error Code” [CR]
9.11.7 CR_LOGO Command
Command
Details
“CR_LOGO”[CR]
Get setting status of Logo
Acceptable
Response
%1
Unacceptable
“000_%1”[CR]
“OFF” ------------------------------ Logo function is OFF
“DFLT” ----------------------------- Default Logo is selected
“USER” ---------------------------- User Logo is selected
“Error Code” [CR]
9.11.8 CR_HDMI SETUP Command
Command
Details
“CR_HDMI SETUP”[CR]
Get status of Image mode in HDMI setup
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“NORMAL” --------------------- Image mode is Normal
“ENHANCED” ----------------- Image mode is Enhanced
“Error Code” [CR]
-63-
LV-8320 Expand Serial Command Functional Specifications
9.11.9 CR_HDMI SETUPSOUND Command
Command
Details
“CR_ HDMI SOUND”[CR]
Get status of Sound mode in HDMI setup
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“HDMI” ---------------------- PCM sound (Digital sound) is selected.
“EXTERNAL” ------------ External sound input is selected.
“Error Code” [CR]
9.11.10 CR_TERMINAL Command
Command
Details
“CR_TERMINAL” [CR]
Get setting status of Terminal
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“COMPUTER”-------------Computer Input mode
“MONITOR”----------------Monitor Out mode
“Error Code” [CR]
9.11.11 CR_PIP Command
Command
Details
“CR_PIP” [CR]
Get status of mode of Picture in Picture
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“OFF” --------------- Picture in Picture is Off
“PINP” -------------- P in P is selected
“PBYP” ------------- P by P is selected
“Error Code” [CR]
9.11.12 CR_PIPSIZE Command
Command
Details
“CR_ PIPSIZE” [CR]
Get selected size of Sub picture in Picture in Picture
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“SMALL” ------------- Sub picture size is Small
“MIDDLE” ------------ Sub picture size is Middle
“LARGE” ------------- Sub picture size is Large
“Error Code” [CR]
9.11.13 CR_PIPPOSITION Command
Command
Details
“CR_PIPPOSITION” [CR]
Get position of Sub picture in Picture in Picture
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“BTMRIGHT” -------------- Sub picture is Bottom right
“BTMLEFT” ---------------- Sub picture is Bottom left
“TOPRIGHT” -------------- Sub picture is Top right
“TOPLEFT” ---------------- Sub picture is Top left
“Error Code” [CR]
-64-
LV-8320 Expand Serial Command Functional Specifications
9.11.14 CR_P-MANE Command
Command
Details
“CR_P-MANE”[CR]
Get Power management mode setting status
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“OFF” -------------------------- Power management mode is OFF
“READY” ---------------------- Power management mode is Standby
“SHUTDOWN” ---- Power management mode is set to Exit
“Error Code” [CR]
9.11.15 CR_P-MANETIME Command
Command
Details
“CR_P-MANETIME”[CR]
Get time to start Power management mode
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“001”~”030” -----------------------1 minute to 30 minutes
“Error Code” [CR]
9.11.16 CR_ON-STA Command
Command
Details
“CR_ON-STA”[CR]
Get Direct power on setting status
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“ON” -------------------------- Direct power on is ON
“OFF” ------------------------- Direct power on is OFF
“Error Code” [CR]
9.11.17 CR_STANDBYMODE Command
Command
Details
“CR_STANDBYMODE” [CR]
Get Standby Mode setting status
Acceptable
Response
%a
Unacceptable
9.11.18
“000_%a”[CR]
“ECO” -------------- Eco Mode
“NORMAL” -------- Normal Mode
“Error Code” [CR]
CR_PTIMEMODE Command
Command
Details
“CR_PTIMEMODE”[CR]
Get operation mode of P-timer.
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“COUNTUP” ---------------- Count up is selected
“COUNTDN” ---------------- Count down is selected.
“Error code”[CR]
-65-
LV-8320 Expand Serial Command Functional Specifications
9.11.19 CR_PTIMER Command
Command
Details
“CR_PTIMER”[CR]
Get current status of P-timer
Acceptable
Response
%a
“000_%a”[CR]
“ON” ------------------------ P-timer is in execution
“STOP” --------------------- P-timer is paused
“OFF” ----------------------- P-timer is inactive
Unacceptable
“Error code”[CR]
9.11.20 CR_PTIME Command
Command
Details
“CR_PTIME”[CR]
Get setting status of Countdown timer.
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“001”~“180” ------------1~180 minutes
“Error code”[CR]
9.11.21 CR_CCAPTIONDISP Command
Command
Details
“CR_CCAPTIONDISP”[CR]
Get selected channel of Closed caption
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“OFF” --------- Off
“CC1” --------- CC1 is selected
“CC2” --------- CC2 is selected
“CC3”--------- CC3 is selected
“CC4” --------- CC4 is selected
“Error Code”[CR]
9.11.22 CR_CCAPTIONCOLOR Command
Command
Details
“CR_CCAPTIONCOLOR_%1”[CR]
Get selected color of Closed caption
Acceptable
Response
%a
Unacceptable
“000”[CR]
“COLOR” ------- Color is selected
“WHITE” -------- White is selected
“Error Code”[CR]
9.11.23 CR_RCODE Command
Command
Details
“CR_RCODE”[CR]
Get selected Remote Control Code
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“001” --------------------------- Code1 is selected
“002” --------------------------- Code2 is selected
“Error Code” [CR]
-66-
LV-8320 Expand Serial Command Functional Specifications
9.11.24 CR_SECURITY Command
Command
Details
“CR_SECURITY” [CR]
Get Security Mode setting status
Acceptable
Response
%1
Unacceptable
9.11.25
“000_%1[CR]
“ON” ------------- PJ Lock setting on Menu is ON-1 or ON-2
“OFF” ------------PJ Lock setting on Menu is OFF
“Error Code” [CR]
CR_KEYDIS Command
Command
Details
“CR_KEYDIS”(CR)
Get disability status of RC/Projector keys (valid or invalid)
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“NONE” -------------------------- RC / Projector keys are valid
“RC” ------------------------------ RC keys are invalid
“KEY” ----------------------------- Projector keys are invalid
“Error Code” [CR]
9.11.26 CR_PJLOCKNOW Command
Command
Details
“CR_PJLOCKNOW” [CR]
Get if PJ lock is actually in operation
Acceptable
Response
%1
Unacceptable
“000_%1[CR]
“LOCK” ------------- PJ Lock is in operation. PJ Lock status is ON-1
or ON-2 on Menu, and PJ PIN CODE is not
entered so that projector is actually locked.
“FREE” ------------- PJ Lock is released. PJ Lock status is OFF, or,
status is ON-1 or ON-2 on Menu but PJ PIN
CODE is entered correctly so that PJ Lock is
released.
“Error Code” [CR]
9.11.27 CR_PJLOCKMENU Command
Command
Details
“CR_PJLOCKMENU” [CR]
Get status of PJ Lock on Menu
Acceptable
Response
%1
Unacceptable
“000_%1[CR]
“ON1” ------------- PJ Lock status is On-1
“ON2” ------------- PJ Lock status is On-2
“OFF” ------------- PJ Lock status is OFF
“Error Code” [CR]
9.11.28 CR_FANMODE Command
Command
Details
“CR_FANMODE”[CR]
Get selected Fan mode
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“L1” ----------------------- Fan mode is L1
“L2” ----------------------- Fan mode is L2
“Error Code” [CR]
-67-
LV-8320 Expand Serial Command Functional Specifications
9.11.29 CR_FANCONTROL Command
Command
Details
“CR_FANCONTROL”[CR]
Get selected Fan control setting status
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“OFF” ----------------------- Fan control is OFF
“ON1” ----------------------- Fan control is ON1
“ON2” ----------------------- Fan control is ON2
“Error Code” [CR]
9.11.30 CR_ DELAYCTRL Command
Command
Details
“CR_DELAYCTRL”[CR]
Get setting status of Video delay control
Acceptable
Response
%1
Unacceptable
“000_%1”[CR]
“ON” ----------------------- Video delay control is active
“OFF” ---------------------- Video delay control is inactive
“Error Code”[CR]
9.11.31 CR_FILH Command
Command
Details
“CR_FILH”[CR]
Get Filter used time
Acceptable
Response
%1
Unacceptable
“000_%1”[CR]
“00000”~”99999” ------------------- 0 hour to 99999 hours
“Error Code”[CR]
9.11.32 CR_FILREPL Command
Command
Details
“CR_FILREPL”[CR]
Get the information of Filter replacement time
Acceptable
Response
%1
Unacceptable
9.11.33
“000_%1”[CR]
“1Y” ------------------- Over filter replacement time
“1N” ------------------ Within filter replacement time
“Error Code”[CR]
CR_FILTIMER Command
Command
Details
“CR_FILTIMER” [CR]
Get setting time which filter warning OSD is displayed
Acceptable
Response
%1
Unacceptable
“000_%1”[CR]
“1000” ----------------- 1000 hours
“2000” ----------------- 2000 hours
“3000” ----------------- 3000 hours
“4000” ----------------- 4000 hours
“5000” ----------------- 5000 hours
“6000” ----------------- 6000 hours
“OFF” ---------------- No OSD display
“Error Code”[CR]
-68-
LV-8320 Expand Serial Command Functional Specifications
9.11.34 CR_TTLPWRSAVEKWH Command
Command
Details
“CR_TTLPWRSAVEKWH”[CR]
Get current value of Total power savings (kWh)
Acceptable
Response
%1
Unacceptable
“000_%1”[CR]
“00000.00”~”99999.99”
“Error Code”[CR]
9.11.35 CR_TTLPWRSAVECO2 Command
Command
Details
“CR_TTLPWRSAVECO2”[CR]
Get current value of Total power savings (CO2)
Acceptable
Response
%1
Unacceptable
“000_%1”[CR]
“00000.00”~”99999.99”
“Error Code”[CR]
-69-
LV-8320 Expand Serial Command Functional Specifications
9.12 Other Status Read Command
9.12.1 CR_STATUS Command
Command
Details
“CR_STATUS”(CR)
Get status of Projector behavior.
This command affects the same as”CR0” of Basic Serial command, but this has
an error code.
Acceptable
Response
%1
Unacceptable
“000_%1”[CR]
“00”= Power ON
“80”= Stand by
“40”= Count down
“20”= Cooling down
“10”= Power failure
“28”= Cooling down due to abnormal temperature
“88”= Stand by after Cooling down
“24”= Power saving cooling down
“04”= Power saving
“21”= Cooling down due to Lamp failure
“81”= Stand by after Cooling down due to Lamp failure
“Error Code”[CR]
9.12.2 CR_SIGNAL Command
Command
Details
“CR_SIGNAL”(CR)
Get Signal status if there is signal or not
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“ON” ------------------------ Signal is found
“OFF” ----------------------- There is no signal
“Error Code” [CR]
9.12.3 CR_VMUTE Command
Command
Details
“CR_VMUTE”[CR]
Get setting status of Blank
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“ON” -------- Blank is ON, User Logo (My picture) is displayed
“OFF” ------- Blank is OFF
“Error Code” [CR]
9.12.4 CR_FREEZE Command
Command
Details
“CR_FREEZE”[CR]
Get setting status of Freeze
Acceptable
Response
%a
Unacceptable
“000_%a”[CR]
“ON” ---------------------- Freeze is ON
“OFF” --------------------- Freeze is OFF
“Error Code” [CR]
-70-
LV-8320 Expand Serial Command Functional Specifications
9.12.5 CR_TEMPWARN Command
Command
Details
“CR_TEMPWARN”[CR]
Get the temperature inside a projector and its condition if it is abnormal
temperature or close to abnormal temperature
If there are several sensors installed, it is possible to get information from all the
sensors at once.
Acceptable
“000_%a_%b_%c”[CR]
%a -------------------- Sensor 1 status
%b -------------------- Sensor 2 status
%c -------------------- Sensor 3 status
“W” ---- Approach or reach abnormal temperature
(dangerous temperature)
“S” ---- Far from abnormal temperature (safe temperature)
“N” ---- Sensor detects no abnormal temperature
Response
%a
%b
%c
Unacceptable
[Example]
“S_W_S”[CR] means Sensor 1 detects safe temperature, Sensor
2 detects abnormal temperature and Sensor 3 detects safe
temperature
Note) When the temperature difference between Sensor 1 and 3
reaches specific value, some of the models detect it as Abnormal
temperature. In this case, the 3rd data shows if the temperature
difference between Sensor 1 and 3 is dangerous state or not. The
3rd data means temperature abnormality due to Sensor 3
When abnormal temperature is not detected by sensor, “N” (No
connection with temperature abnormality) is returned.
“Error Code” [CR]
-71-
LV-8320 Expand Serial Command Functional Specifications
9.12.6
CR_TEMP Command
Command
Details
"CR_TEMP”[CR]
Get current temperature inside a projector.
If there are several sensors installed, it is possible to get information from all the
sensors at once.
Acceptable
“000_%1_%2_%3”[CR]
%1= Sensor 1 temperature (Outside temperature)
%2= Sensor 2 temperature (Inside temperature1)
%3= Sensor 3 temperature (Inside temperature2)
%1,%2 are consists of 6 bites fixed
There must be 1 space between %1 and %2, and, %2 and %3
e.g. _31.5F
“_” means a space and “_” changes into “-“, when temperature
gets below freezing.
e.g. -05.5F
The last character shows if corresponding sensor is under
abnormal temperature.
Response
%1,%2,%3
“F” ------- Abnormal temperature
“W”-------Close to abnormal temperature(Temperature is as high
to display Warning)
“S” -------Not close to abnormal temperature (Temperature is low
enough and safe.)
“N”-------Applicable sensor does not detect abnormal temperature
“E” -------Not able to return temperature data
When several sensors are incorporated, projector returns values
continuously.
e.g. “_31.5F__35.2S__38.0W”[CR]
A data of sensor 1 comes first and a data of sensor 2 follows after
1 space.
As described respectively in e.g., sensor 1 detects abnormal
temp., sensor 2 detects 35.2 degrees which means safety, and
sensor 3 is 38 degrees which is close to abnormal temp.
In case projector cannot return its data due to some hard ware
failure, the last character becomes “E” such as “_00.0E”.
Some of the projectors get abnormal temperature because of
heat of Lamp ballast in Standby mode or Powering ON.
Therefore detection of abnormal temperature is suspended while
Standby mode or adequate time after Power ON, and during that
time projector returns “_----N” as a temperature data.
Unacceptable
“Error Code”[CR]
-72-
LV-8320 Expand Serial Command Functional Specifications
9.12.7
CR_TEMPFAIL Command
Command
Details
"CR_TEMPFAIL”[CR]
Get the temperature inside a projector when abnormal temperature occurs.
If there are several sensors installed, it is possible to get information from all the
sensors at once.
Acceptable
“000_%a_%b_%c”[CR]
%a ------------------ Sensor 1 temp. (External temp.)
%b ------------------ Sensor 2 temp. (Internal temp.1)
%c ------------------ Sensor 3 temp. (Internal temp.2)
[Example]
“_31.5F”[CR]
“_” indicates a space. When the temperature sinks to -, the first
character is “-” like “-05.5F”[CR]
The last character means the sensor’s status if it reaches
abnormal temperature
Response
%a
%b
%c
Exceeding critical temp. ------------------------------ “F”
Temp. is safe -------------------------------------------- “S”
Sensor detects no critical temp.--------------------- “N”
The example shows that sensor 1 indicates 31.5 degrees and the
temperature is abnormal.
When the temperature is safe, all data are represented as
“□000S”.
When the projector is reset, “□000S” is set, and every time
abnormal temperature occurs, it renews the data and returns it.
In short, it only returns the renewed data of the latest abnormal
temperature and the previous data is deleted.
Unacceptable
“Error Code” [CR]
9.12.8 CR_SERIALNO Command
Command
Details
“CR_SERIALNO” [CR]
Get value of the serial number.
Acceptable
Response
%1
Unacceptable
“000_%1” [CR]
Eight digits of alphanumeric characters
“Error Code” [CR]
-73-
Download PDF