Dimplex | Pizzeria 600 | User Manual

Users Guide
Handbook
Built In
Pyrolytic
Caution: Read the
instructions before using the
appliance
CUSTOMER CARE HELPLINE - AUSTRALIA: 1-300-556-816
NEW ZEALAND: 09-274-8265
WEBSITE:WWW.BELLING.COM.AU
PART NO: 082761500
DATE: 17/01/2014
CONTENTS & INTRODUCTION
CONTENTS & INTRODUCTION
SAFETY
GETTING TO KNOW YOUR PRODUCT
USING YOUR PRODUCT
USING YOUR PROGRAMMER
CLEANING
INSTALLATION
TECHNICAL
Introduction
Should you need it . . . .
CUSTOMER CARE
Inside the paperwork which has come with this appliance, there is a leaflet and
card explaining the terms of our warranty and guarantee. Simply fill in the details
on the card and post it off, this will register your appliance.
Glen Dimplex Australia PTY LTD
Glen Dimplex New Zealand Pty
1/21 Lionel Road
38 Harris Road,
Mount Waverley
East Tamaki
Victoria 3149Auckland
AustraliaNew Zealand
Ph: 1300 556 816
Ph: 09 274 8265
Fx: 1800 058 900
Fx: 09 274 8472
If your appliance is covered by the warranty and guarantee, you will not be billed
for work undertaken should your appliance be faulty, terms and conditions do
apply, so please read through the literature carefully.
Please ensure that you have available your appliances model number and serial
number, there is a space at the back of this book for recording that information.
Important Notice
Please note there may be a cooling fan fitted to this appliance. It is an integral
part of its safety and functionality. When the appliance is installed care must be
taken that the cooling fans performance is not impeded by any objects coming
into contact with it. (Installation pipes, leads etc) Care must also be taken that
there is sufficient air flow at the rear of the appliance for the cooling fan to run at
its optimum efficiency, (particularly built in appliances) see clearance dimensions
in the installation section of the booklet. During use the appliance must never be
disconnected from the mains supply as this will seriously affect the safety and
performance of the appliance, particularly in relation to surface temperatures
becoming hot and gas operated parts not working efficiently. The cooling fan is
designed to run on after the control knob has been switched off to keep the front
of the appliance and the controls cool until the appliance has naturally cooled
itself.
3.101
1
SAFETY
•
The manufacturer is not responsible if an incorrect installation
and use, causes injuries and damage.
•
Make sure that you have removed all packaging and wrapping. Some of the items inside this appliance may have additional wrapping.
•
It is advised that you turn the ovens and/or grill on for a short
while. This will burn off any residues left from manufacturing.
There may be a smell which accompanies this process - but
this is nothing to worry about and is harmless.
•
It is recommended that you wash the oven shelves, baking
tray, grill pan and grill pan trivet before their first use in hot
soapy water. This will remove the protective oil coating.
WARNING!
• The appliance and its accessible parts become hot during use.
• Care should be taken to avoid touching
heating elements.
• Children less than 8 years of age shall be
kept away unless continuously supervised.
• This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning the use of
the appliance in a safe way and understand
the hazards involved.
• Children shall not play with the appliance.
5.401
2
SAFETY
BEFORE USING THE PRODUCT
SAFETY
• NEVER try to extinguish a fire with water,
but switch off the appliance and then cover
the flame with a lid or damp cloth.
• Danger of fire: Do not store items on the
cooking surfaces.
• Servicing should be carried out only by authorised personnel.
• Do not operate the appliance without the
inner door glass correctly fitted.
• Never put items directly on the base of the
oven or cover the oven base with foil, as this
can cause the base element to overheat.
• Do not modify the outer panels of this appliance in any way.
• Do not use harsh abrasive cleaners or sharp
metal scrapers to clean the oven door glass
since they can scratch the surface, which
may result in shattering of the glass.
• Ensure that the appliance is switched off
before replacing the lamp to avoid the possibility of electric shocks.
• This appliance must be earthed.
5.401
3
SAFETY
• Cleaning and user maintenance shall not be
made by children without supervision.
SAFETY
SAFETY
CAUTION!
•
Do not spray aerosols in the vicinity of this appliance while it
is in operation.
•
Do not store or use flammable liquids or items in the vicinity
of this appliance.
•
Do not modify this appliance.
•
This appliance is for cooking purposes only. It must not be
used for other purposes, for example room heating.
•
The top element gets extremely hot when in use, so take extra
care to avoid touching it.
OVEN/GRILL
•
Always take care when removing food from the oven as the
area around the cavity may be hot.
•
Always use oven gloves when handling any utensils that have
been in the oven as they will be hot.
•
Always make sure that the oven shelves are resting in the
correct position between two runners. Do not place the oven
shelves on top of the highest runner, as this is not stable and
can lead to spillage or injury.
•
Always use the minute minder if you are leaving the oven
unattended. This reduces the risk of food burning.
•
Never place items on the door while it is open.
•
Never wrap foil around the oven shelves or allow foil to block
the flue.
•
Never drape tea towels near the oven while it is on; this is a
fire hazard.
•
Never pull heavy items, such as turkeys or large joints of meat,
out from the oven on the shelf, as they may overbalance and
fall.
•
Never close the door while in the grill mode.
5.401
4
SAFETY - PYROLYTIC CLEANING
Before carrying out a Pyrolytic self-cleaning function or the
First Use function, please remove from the oven cavity:
- Any excess food residues, oil or grease spills / deposits.
- Any removable objects (including shelves, side rails and grill
pans provided with the product)
•
Read carefully all the instructions for Pyrolytic cleaning.
•
Keep children away from the appliance while the Pyrolytic
cleaning is in operation. The appliance becomes very hot.
•
Pyrolytic cleaning is a high temperature operation that can
release fumes from cooking residues and construction materials, as such consumers are strongly advised to:
- Provide good ventilation during and after each Pyrolytic
cleaning.
- Remove any pets (especially birds) from the vicinity of the
appliance location during and after the Pyrolytic cleaning, and
first use maximum temperature operation, to a well ventilated
area.
•
Unlike all humans, some birds and reptiles can be extremely
sensitive to potential fumes emitted during the cleaning process of all Pyrolytic Ovens.
•
Non-stick surfaces on pots, pans, trays, utensils etc., can be
damaged by the high temperature Pyrolytic cleaning operation of all Pyrolytic Ovens, and can also be a source for low
level, harmful fumes.
•
Fumes released from all Pyrolytic Ovens / Cooking Residues
as described are not harmful to humans, including infants or
persons with medical conditions.
5.402
5
SAFETY - PYROLYTIC CLEANING
•
GETTING TO KNOW YOUR OVEN
Man
P
80
S
240
220
FUNCTION
120
200 180
160
GETTING TO KNOW YOUR OVEN
1
h:min
min:sec
Auto
140
4
2
3
5
6
7
1. Control panel 2. Grill 3. Light 4. Door lock 5. Shelf runners
6. Oven fan 7. Inner door glass
Oven Temperature
Indicator
h:min
min:sec
Auto
Man
P
80
S
240
FUNCTION
Oven
functions
Timer &
Programmer
220
120
200 180 200
140
Oven Temperature Control
Door Lock
Indicator
9.900
6
GETTING TO KNOW YOUR OVEN
GETTING TO KNOW YOUR OVEN
(Function buttons
dependant on model)
FUNCTION
(Function buttons
dependant on model)
Minute minder
Pyrolytic cleaning mode
Cooking time
,
,
Volume level
End of cooking time
7-segment display
Time of day
Max. adjustable minute minder
Child lock
Max. adjustable cooking time
Cooking pot
Display hours:minutes
Automatic mode
Display minutes:seconds
Manual mode
SET CLOCK - TIME
After connecting the appliance for the first time:
1. The display shows
flashing.
2. Press the Function Button until this
3. Adjust the time with
and
symbols shows
keys until the correct time is shown
4. Leave for 5 seconds
9.900
7
S
9.900
GETTING TO KNOW YOUR OVEN
Recommended Uses
Grill
Ideal for anything from toast to steaks.
Fanned Grill
The fan allows heat to circulate around the food.
Ideal for thinner foods such as bacon, fish and
gammon steaks. Foods do not require turning. Use
with the oven door closed
Conventional Oven
This function is ideal for traditional roasting. The
meat is placed in the middle of the oven, roast potatoes towards the top. The temperature selected
corresponds to the temperature in the centre of
the oven.
Top Heat Only
The heat is ideal for browning the tops of food as it
is not as fierce as the grill following conventional or
fanned cooking. Provides additional browning for
dishes like Lasagna or Cauliflower cheese.
Base Heat Only
The base heat can be used to provide additional
browning for pizzas, pies and quiche. Use this function towards the end of cooking.
Fanned Oven
The fan circulates air giving an even temperature
in the oven, making this function suitable for batch
baking, or batch cooking foods.
Fan and Base Heat Only
Used to cook open pies (such as mince pies) the
base element ensures that the base is cooked while
the fan allows the air to circulate around the filling
- without being too intensive.
Intensive Bake
Suitable for food with a high moisture content,
such as quiche, bread and cheese cake. It also
eliminates the need for baking pastry blind.
Defrosting and
Cooling
To defrost foods, such as cream cakes/gateaux, use
with the oven door closed. For cooling dishes prior
to refrigeration, leave the door open. Place food in
the centre of the oven.
Oven Temperature
Indicator
If lit, the oven has not reached the desired temperature.
Door Lock Indicator
When the oven temperature is too high or in pyrolytic mode, this indicator will light up.
Slow Cook
For slow cooking foods such as stews and casseroles.
Pyrolytic
Turn to Pyrolytic cleaning mode.
8
GETTING TO KNOW YOUR OVEN
Symbol Function / Feature
USING YOUR OVEN
As part of the cooking process, hot air is expelled through a vent in the oven.
When opening the oven door, care should be taken to avoid any possible
contact with potentially hot air, since this may cause discomfort to people with
sensitive skin. We recommend that you hold the underneath of the oven door
handle.
PREHEATING
Always use the fan oven setting for preheating to save time and electricity.
After the oven has been preheated on the fan oven setting, turn the selector
control knob to the oven setting you require. The oven must be preheated
when cooking frozen or chilled food, and we recommend preheating for yeast
mixtures, batters, soufflés and whisked sponges, otherwise preheating is not
necessary as a fan oven warms up quickly. Preheat the oven until the oven temperature indicator switches off for the first time; this will take between 5-15
minutes, depending on the temperature selected.
TO HELP THE AIR CIRCULATE FREELY
•
Position the shelves evenly within the oven and maintain a clearance from
the oven roof and base.
•
If more than one cooking dish or baking tray is to be used on a shelf, leave
a gap of at least 25mm between the items themselves and the oven interior.
•
Allow enough space between shelves for food that will rise during cooking.
•
Do not place items on the oven base as this will prevent air from circulating freely
TO TURN ON THE OVEN
Ensure that
(manual) is displayed on the programmer.
1. Select the function Turn the oven function control knob to the desired
function.
2. Set the temperature control If you have selected an oven cooking function, then simply turn the oven temperature control knob to the required
temperature - this turns on the indicator light, which will stay on until the
oven reaches the required temperature.
3. Turn off To switch off the oven, return both of the control knobs to the off
position.
9.901
9
USING YOUR OVEN
CAUTION!
USING YOUR OVEN
Make sure that frozen foods are thoroughly thawed before cooking.
•
Do not slow cook joints of meat or poultry weighing more than
2¼kg/4½lb.
•
Preheat the oven to 170°C and cook for 30 minutes, then adjust the oven
control to S for the remainder of the cooking time.
•
Slow cooking times will be about 3 times as long as conventional cooking
times.
•
Do not open the oven door unnecessarily during slow cooking, as this will
result in heat loss at low temperatures, and significantly increase the cooking time.
•
Always use dishes with tightly fitting lids. To rectify badly fitting lids, place
foil over the dish underneath the lid.
Defrosting
Small or thin pieces of frozen fish or meat - e.g. fish filets, prawns & mince will
take approximately 1-2 hours.
Placing the food in a single layer will reduce the thawing time.
A medium sized casserole or stew will take approximately 3-4 hours.
A 1½kg/3lb oven ready chicken will take approximately 5 hours, remove the
giblets as soon as possible.
BE SAFE
•
Do not defrost stuffed poultry using this method.
•
Do not defrost larger joints of meat and poultry over 2kg/4lb using this
method.
•
Never place uncooked food for defrosting next to cooked food which is to
be cooled, as this can lead to cross contamination.
•
Defrosting meat, poultry and fish can be accelerated using this method,
but make sure they are completely thawed before cooking thoroughly.
Place meat and poultry on a trivet in a meat tin.
Oven furniture
Oven shelves
The oven shelf must be positioned with the up-stand at the rear of the oven
and facing upwards.
9.901
10
USING YOUR OVEN
Slow cooking
S •
USING YOUR OVEN
The cooling fan
The cooling fan may operate when the main oven is on and may continue to
operate for a period after the oven has been switched off, to help cool the cavity down.
To cool foods after cooking prior to refrigerating or freezing, turn the oven
function control to the defrost position and open the door.
Using Aluminium Foil
Using aluminium foil to cover the grill pan, or putting items wrapped in foil
under the grill creates a fire hazard.
9.901
11
USING YOUR OVEN
Position baking trays and roasting tins on the middle of the shelves.
USING THE PROGRAMMER
USING THE PROGRAMMER
Symbols & functions:
(Function buttons
dependant on model)
FUNCTION
(Function buttons
dependant on model)
Minute minder
Cooking time
Pyrolytic cleaning mode
,
,
Volume level
End of cooking time
7-segment display
Time of day
Max. adjustable minute minder
Child lock
Max. adjustable cooking time
Cooking pot
Display hours:minutes
Automatic mode
Display minutes:seconds
Manual mode
USING THE TOUCH CONTROLS
Select a function - scroll through by touching
Plus - increase time or volume
Minus - decrease time or volume
PROGRAMMER FUNCTIONS
The chosen function will start automatically five seconds after setting. The
display shows the current time of day, except when the minute minder is active.
In this case, the display shows the remaining time of the minute minder.
MANUAL
If no programme is set, the display shows
gramme is set, the display shows
.
and the time of day. If the pro-
In the event of a power failure, the oven & grill elements will not automatically
switch on when power is resumed; thus, on resumption of power, refer to Set
Clock-Time.
11.700
12
USING THE PROGRAMMER
USING THE PROGRAMMER
SELECT
FUNCTION
OR
FUNCTION
1st TOUCH
MINUTE MINDER
2nd TOUCH
COOK TIME
3rd TOUCH
END OF COOK
4th TOUCH
TIME ADJUST
5th TOUCH
VOLUME ADJUST
MINUTE MINDER
The minute minder can be set using the
99 minutes.
or
symbols up to a maximum of
The display shows the symbol
& the remaining time is displayed continuously. While setting other functions, the timer counts down in the background.
The remaining time can be changed at any time by using the
or
bols. The countdown is deleted by setting the minute minder to
sym.
The minute minder time has expired once it reaches
; the alarm is heard.
Touching any timer control stops the alarm and the time of day is displayed.
COOKING TIME (The duration of time the oven will operate for before turning off)
The symbol
is flashing. The cook time can be set using the
bols up to a maximum time of
.
Once set,
, the symbol
or
& the time of day are displayed.
To change the time, repeat the steps above. To delete, set the time to
11.700
sym-
.
13
USING THE PROGRAMMER
The end of cooking time can be set using the
or
of cooking time is limited to the time of day plus
Once set, the display changes to
the time of day.
symbols. The latest end
.
& the display shows the symbol
and
To change the time, repeat the steps above. To delete, set the time to
.
DELAYED COOKING (An automatic function to have food ready for a desired time of day)
Set the oven function and temperature
Set the desired cooking time - see section cooking time.
Set the desired end of cooking time - see section end of cooking time.
Once set the display will show
Once active, the display will show
.
and the symbol
.
To change the time, repeat the steps above. To delete, set the time to
.
VOLUME
The symbols
(Low, Medium and Loud) will appear on the display.
The volume can be adjusted by touching the .
After seven minutes maximum or after touching any of the touch control keys,
the alarm stops but
continues to flash. Touch the function symbol, the
symbol is displayed continuously & the time of day is displayed, except if
the minute minder is active.
CHILD LOCK
The child lock function can be activated while the time of day is displayed in
mode, regardless of any programme modes that are set.
is activated by touching the
symbol for a minimum of five seconds until
is displayed. From this moment on all other functions are locked.
Exception: if a function e.g. cooking time has expired, the alarm can be terminated by touching any of the touch control symbols, although the child lock is
active.
Touching any of the touch control symbols while the child lock is activated
results in an alarm & the symbol flashing for two seconds.
The child lock function is de-activated by touching the
symbol for a minimum of five seconds until the symbol switches off. From this moment on all
11.700
14
USING THE PROGRAMMER
END OF COOKING TIME (The time of day the oven will turn off)
USING THE PROGRAMMER
Activating the child lock in manual mode completely locks the appliance & the
symbol is switched off. After de-activation, as described above, the
symbol is displayed again.
The child lock remains activated after a power failure. Before renewing the settings, the child lock has to be deactivated, as described above.
11.700
15
USING THE PROGRAMMER
functions are selectable again.
USING PYROLYTIC CLEANING
The glass in the door should always be kept clean. To remove stubborn
dirt and stains, use absorbent kitchen roll or a damp sponge and an ordinary detergent.
•
If the oven is installed underneath a hob, make sure that the burners or
electric plates/zones remain turned off during the automatic cleaning
cycle.
•
Do not use abrasive or corrosive cleaners for cleaning the door glazing (e.g.
powder products, stain removers and metal scouring pads).
•
Do not use rough or abrasive materials or sharp metal scrapers to clean the
glass on the oven door since they may scratch the surface.
•
Before starting the Pyrolytic cleaning cycle, make sure that the oven does
not contain any foods or large spills from previous cooking operations.
PYROLYTIC OVEN CLEANING
Pyrolytic cleaning is an automatic high-temperature cleaning procedure which
causes dirt to dissolve. Due to this process, it is possible to clean the inside of
the oven more easily.
During the automatic cleaning cycle, unpleasant smells may occur due to the
normal pyrolytic cleaning process. This is normal.
During the pyrolytic cycle, the door will lock making it impossible to open the
door. The door lock indicator will be lit on the Control Panel.
As soon as the pyrolytic cycle is activated, the door lock will lock. This will
remain locked until the cleaning cycle has completed and the oven temperature has decreased to a safe level. The control knob must be turned to the off
position to release the lock and allow the door to open.
BEFORE STARTING THE PYROLYTIC CLEANING CYCLE
Pyrolytic cleaning may be carried out at any time of the day or night. If available
and low energy rates apply, you may benefit from the lower cost of electricity
at night.
•
Completely remove all accessories (i.e. shelves, pans) from inside the oven.
•
Remove the telescopic runners, see “Cleaning”
•
Make sure that the oven door is firmly closed.
•
At the end of the cleaning cycle, when the oven has cooled down, reinsert
the runners and accessories by repeating the previously used procedure in
reverse order.
10.004
16
USING PYROLYTIC CLEANING
•
USING PYROLYTIC CLEANING
Select Pyrolytic function
on your oven function control. The display should
show the default cleaning time of 2:00 hours. To start the cleaning process,
touch the
and the P symbol will flash for 5 seconds.
OR
FUNCTION
The door will lock within the pyrolytic cycle and the door lock indicator will
come on. This will stay on until the oven is at the final stage of the cool down
process.
h:min
min:sec
Auto
Man
80
P
S
240
220
120
200 180
160
140
After the light goes out, the door can be opened. We suggest for you to leave
the oven to cool for another 30 minutes before cleaning away any ash. For the
best results, we suggest you clean the cavity, base and walls with a damp cloth.
ALTERNATIVE CLEANING CYCLES OR START TIMES
Whilst the
and P are flashing, the pyrolytic cycle can be decreased to 1:00
hour by pressing
or increased to 3:00 hours by pressing
.
To set a start time - see section end of cooking time.
When the pyrolytic cycle is completed, you will hear an alarm and the P symbol
will flash. This will continue for 7 minutes or until you touch any of the touch
keys. The time of day will then be displayed.
CLEANING
DURATION
LIGHT DIRT
1 hour
MEDIUM DIRT
2 hours
HEAVY DIRT
3 hours
POWER FAILURE IN PYROLYTIC MODE
If the power fails, you will need to reset time of day. The child lock may need to
be deactivated before using the oven. See sections - set the clock and child lock.
To avoid an unwanted start of pyrolytic cleaning, the duration is set to
. The display shows
and the symbol
. The symbol P flashes until a
new oven mode is selected.
At the end of the pyrolytic cycle, the fan will continue to run for a period of time
to cool the product.
10.004
17
USING PYROLYTIC CLEANING
START PYROLYTIC CLEANING
CLEANING
•
It is important to clean the product regularly as a build up of fat can affect
its
performance or damage it and may invalidate your guarantee.
•
Always switch off your appliance and allow it to cool down before you
clean any part of it.
Do not use undiluted bleaches, products containing chlorides, wire wool
or abrasive cleaners on aluminium, stainless steel, or plastic/painted parts
as they can damage the appliance. Nylon pads can also be unsuitable.
Take extra care when cleaning over symbols on fascia panels. Excessive
cleaning can lead to the symbols fading.
If your product is fitted with stainless steel cladding, you may notice a
small white residue on the outer edges. This can be removed with a non
abrasive wipe.
Use a moist, soapy pad or cloth to clean painted, plastic and chromed
parts.
•
•
•
•
Stainless steel & Aluminium surfaces
•
Only use a clean cloth wrung out in hot soapy water, and dry with a soft
cloth.
•
Stubborn marks can be removed using a stainless steel cleaner. Supplies
can be purchased from the Customer Care Centre.
Sharp objects can mark the surface of stainless steel, but will become less
noticeable with time.
Wipe any spillage immediately, taking care to avoid burning your hands
Some foods are corrosive e.g.; vinegar, fruit juices and especially salt - they
can mark or damage the metal if they are left on the surface.
Baby oil can be used to restore stainless steel finishes - but only use a few
drops. Don’t use cooking oils as they can contain salts, which will damage
the metal.
•
•
•
•
•
Do not use steam cleaners.
Glass parts
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven
door glass since they can scratch the surface, which may result in shattering of
the glass.
•
Only use a clean cloth wrung out in hot soapy water, or a specialist glass
cleaner.
•
Rinse away any excess cleaner and dry with a soft cloth.
12.301
18
CLEANING
General
CLEANING
For your safety, glass door panels are made of toughened glass. This
ensures that, in the unlikely event that a panel breaks, it does so into small
fragments to minimise the risk of injury. Please take care when handling,
using or cleaning all glass panels, as any damage to the surfaces or edges
may result in the glass breaking without warning or apparent cause at a
later date. Should any glass panel be damaged, we strongly recommend
that it is replaced immediately.
Removing Oven Parts For Cleaning
TELESCOPIC SHELVING SYSTEM
The telescopic shelving system is fitted to suit the most commonly used locations in your cavity.
•
The shelves with the telescopic system are easier to pull out than traditional shelving, which means the oven door stays open for a shorter period
of time. The smooth action also reduces the likelihood of fat, or food, spillage, and gives you extra security.
•
You do not have to use the telescopic shelves all of the time. You can place
the shelves in the traditional positions if you would like more choice.
•
The telescopic shelves remove easily from the runner for re-positioning
or cleaning, but we recommend that you reposition your shelving before
cooking, and remove the shelving for cleaning when the shelves are cold
to prevent burning yourself.
To remove the telescopic shelves or pan (if
included) from the telescopic runners
•
Make sure the shelf/pan is cool enough to touch.
•
Push the oven shelf/pan back into the cavity,
until it hits the stop position.
•
Grasp the shelf/pan in the centre, and lift the
back of the shelf/pan clear of the stop position.
•
You can then lift the front of the shelf/pan clear
of the retaining tabs.
Make sure the shelf
is firmly pressed against
the stop position at
back of the oven cavity
1. Grasp and
lift shelf bars
Note: Make sure the shelf is
unclipped from the retaining
tabs before removal.
2. Lift shelf
clear
To replace the telescopic shelves or pan (if
included)
Make sure the oven runners are pushed all the way
back into the cavity.
•
12.301
Repeat the above step in reverse order
19
CLEANING
•
Whilst every care is taken to eliminate burrs and raw edges from this product,
please take care when handling - we recommend the use of protective gloves
during installation.
Please note that the weight of this appliance is approximately 41kg (unpacked). Take care when lifting it into the housing unit - always use an appropriate method of lifting.
Remove the fixing screws included with the appliance, but leave the appliance
in the base tray packaging until you are ready to install it.
If this appliance is to be installed near to a corner
where the adjacent cabinets run at right angles forward of the appliance, there must be a gap of at least
90 mm between the appliance and the cabinets, to
prevent overheating of the cabinets.
Housing dimensions
•
The appliance is designed to fit into a standard 600mm wide housing unit
with minimum internal dimensions as shown.
600mm is to the underside of the work top when the appliance is built under,
or to the underside of the panel above, when the appliance is installed into a
tall housing unit.
547mm
568mm
20mm
585
560mm MIN
WIDTH
KICK BOARD
5m
m
6m
59
56
PLINTH
m
550mm MIN
DEEP
CABINET
LEG
590mm MIN
600mm MIN
WORK TOP
(UNDERSIDE)
CIA GLASS
TOP OF FAS
588mm TO
BRACKET
OF FASCIA
P
TO
TO
mm
WALL
12mm
GAP IN
PLINTH
INSTALLATION
Do not lift the appliance by the door handle.
WALL
FLOOR
1. When installed in a typical
600mm deep built in housing unit, the false back should be removed from
the housing unit to provide the necessary depth for installation.
2. When the false back is removed, it is normally the case that the support
shelf for the appliance leaves a gap between the back edge and the wall of
approximately 80mm.
3. If no gap occurs between the back edge of the shelf and the wall behind
13.500
20
INSTALLATION
STEP 1 : PREPARE INSTALLATION
WALL
5mm MIN
CLEARANCE
WORK TOP
FRONT OF
COOKER
5mm MIN
CLEARANCE
INSTALLATION
4. When installing the appliance below
a work top, there must be a minimum
ventilation area of 60cm2 below the
appliance, either through the plinth or
through the kick board, as indicated
on the previous page. There must be a
minimum 5mm gap between the front
top edge of the oven and the underside of the work top.
AIRFLOW
SUPPORT SHELF
80mm MIN TO
BACK OF
SUPPORT
SHELF
AIRFLOW
CABINET BASE
AIRFLOW
FLOOR
5. A 12mm deep gap should be cut into the plinth adjacent to the front bottom edge of the appliance, to improve airflow.
Important: Do not modify the outer panels of this appliance in any way.
Ensure that you route all mains electrical cables and flexible tubing well clear of
any adjacent heat source, such as an oven, grill or hob.
Installing the appliance under a work top
Where the appliance is installed under a work top, with a hob installed above it,
the installation instructions for the hob must be read in conjunction with these
instructions.
Important: If a hob is fitted above your appliance always ensure it is well sealed
to prevent water damage to your new appliance.
60cm Terminal Block
Connection Schematic
STEP 2 & 3 CONNECT TO THE ELECTRICITY
SUPPLY
We recommend that the appliance is connected by a competent person who is a
member of a “Competent Person Scheme”
& who will comply with the I.E.E. & Local
regulations.
4
Important: Ensure that you route all mains
electrical cables well clear of any adjacent
heat source, such as an oven or grill.
2
Warning! This appliance must be
earthed.
For 60cm BI appliance:
1. Where a fixed connection is used, a
device allowing the appliance to be isolated on all poles from the mains supply
13.500
5
3
1 Door release tabs
2 Cable clamp screw
3
Cable clamp
1
BROWN / L
4
Live
5
Neutral
230V.....240V
BLUE / N
GREEN/YELLOW / PE
Earth
21
INSTALLATION
the unit, we recommend that a gap of
at least 80mm is made by shortening
the shelf.
INSTALLATION
2. Use a 13 amp fuse.
3. A type HO5 V V-F cable must be used as the mains lead. The cross section
must be a minimum of 1.5mm².
4. The mains terminal block is sited on the right of the angled part of the
service panel.
5. Follow the terminal block connection schematic.
6. Firstly open the terminal block cover by inserting a small flat bladed
screwdriver into the door release tabs.
7. Remove the cable clamp screw to release the cable clamp.
8. Strip the wires back & connect to the terminal block as appropriate.
9. Fit the cable clamp & secure with the screw provided.
10. Close the terminal block, ensuring that the cover is closed and all screws
are tight and in place.
STEP 4: SECURE APPLIANCE INTO HOUSING UNIT
Note : The unit housing the appliance must be appropriately fixed. Ensure that the appliance is centrally
located. Take care not to damage the appliance or
cabinet.
60cm ovens Fixing positions
•
13.500
Open the oven door and screw the 4 fixing screws
through the holes in the front frame.
22
INSTALLATION
with a contact opening width of at least 3mm must be provided.
TECHNICAL
TECHNICAL
ELECTRIC PRODUCTS
Electrical supply/load 240V ~ 50Hz
60cm: load = 2680W
Countries of destination
AU. Australia - NZ. New Zealand.
WARNING! This appliance must be earthed.
The Data badge is located at the bottom of the front frame, behind the door
and rear of the product.
14.701
22
23
Bn
Bn
Thermal
Switch
Thermal
Switch
T‘STAT
2
Bn
W
W
Y
Door Lock
Neon V
T’stat
Bk Neon
Bk
Bn
Bu
V
11
14
12
Bn
FAN
TIMER
PCB
O/P L N
PYRO
T‘STAT
21
24
22
Y
Tangential Cooling Fan
I/P 1
32
31
I/P 2 I/P 3
W
R
Wiring colour code: Bk - Black, Bn - Brown, Bu - Blue,
Gn - Green, Or - Orange, R - Red, W - White, Y - Yellow.
R
1
Wiring Diagram
Bk
Bk
W
W
R
Bn
Bn
V
Bn
X7
X1
X2
L
V
N
Bk Bu
PROGRAMMER
Relay
Bk
Gn
Bn
60 Built In PYROLYTIC
LAMP
Bu
Or
Bn
W
Bu
R
R
Gn
V
2
P2
Or
Bu
OVEN
ELEMENT
W
M.O. BASE ELEMENT
Bu
R
Bn
M.O. GRILL ELEMENT
Bn
1
P1
R
Or
8
7
P7
P8
Y
Or
Bn
R
W
Y
6
5
4
3
2
1
P6
P5
P4
P3
P2
P1
Bu
Bk
OVEN
STIR FAN
Y
Bn
Bn
R
Motor
Bn
Bk
Door
Interlock
W
V
R
Bk
082761601
WIRING
WIRING
14.702
CUSTOMER CARE
What parts of the appliance can be washed in a dishwasher?
•
Any enamelled parts such as the grillpan can be cleaned in a dishwasher,
as can oven shelves and shelf guides.
There’s been a power failure and the product won’t work.
•
Switch off the electricity supply.
•
When the power returns switch the electricity supply back on and re-set
any
programmer/clock to the correct time of day.
My oven is a single combined oven and grill - can I use both functions
together?
•
No. You can only use one or the other.
Why is there condensation on the doors?
•
Condensation is caused by hot, moist air meeting a cooler surface (i.e. the
oven door). You cannot always prevent it, but you can minimise it when it
happens by doing the following:
•
Pre-heat the oven at a high temperature before putting food in the oven,
and cover the food you are cooking wherever possible.
•
Whenever you can, cook wet foods at higher temperatures.
•
Don’t leave food in the oven to cool down.
•
Automatic cooking will normally produce condensation when the oven is
cooling down with food inside.
Should the cooling fan continue to run once the appliance has been
switched off?
•
Yes. This is to make sure that you can always touch the control knobs to
make temperature adjustments, and turn your appliance off.
The neon on my appliance keeps going out and coming back on again - is
this right?
•
Yes. In most cases the neon (if fitted) will cycle on and off to show that
oven is maintaining your temperature choice.
•
This will also happen when the door interlock is operated.
Call Customer Care for a Service Engineer’s visit if:
•
You find that the oven becomes hotter at a particular temperature - the
thermostat may need replacing.
•
The cooling fan fails to work.
15.100
25
CUSTOMER CARE
FAQ’S
CUSTOMER CARE
CUSTOMER CARE
Optional Extras
A grill pan handle can be purchased as an optional extra from our Customer
Care department quoting the part numbers below:
HANDLE - 082283705
HANDLE GRIP - 082469100
COMPLETE GRILLPAN PACK - 012635666
CHANGING LIGHT BULBS
Warning!: There is a risk of electric shock, so
always make sure you have turned off and unplugged your appliance before starting. Always
allow the product to cool down before you
change a bulb.
Please remember that bulbs are not covered by your warranty.
HOW TO CHANGE YOUR LIGHT BULB
•
Remove the shelves
•
Unscrew the lens cover by turning anti-clockwise
•
Remove the bulb and replace
•
Replace the lens cover and oven back
15.100
26
CONTACT US
Calling for a service
If you should experience any problems with your cooker please contact your retailer or
place of purchase.
Important note:
Service work is to be conducted by authorised persons only. It is advisable to have
your cooker checked regularly and maintained in good condition. An annual maintenance is recommended.
Always check the instruction book before calling a service agent to make sure you have
not missed anything.
Glen Dimplex Australia Pty Ltd Customer Care:
Tel: Australia 1-300-556-816
New Zealand 09-274-8265
Before you contact a service agent, make sure that you have the following information
to hand:
Model Number
Serial Number
Date of Purchase
Postcode
Glen Dimplex Australia PTY Ltd, Unit 1/21, Lionel Road,
Mount Waverley, Victoria 3149, Australia.
e-mail: sales@glendimplex.com.au
web: www.glendimplex.com.au
Download PDF