Dual | XDM7615 | User`s manual | Dual XDM7615 User`s manual

XDM7615
INSTALLATION/OWNER'S MANUAL
AM/FM/CD/MP3/WMA Receiver
with 2-Step Motorized Detachable Face
XDM7615 INSTALLATION
Preparation
Please read entire manual before installation.
Before You Start
•Disconnect negative battery terminal. Consult a qualified technician for instructions.
•Avoid installing the unit where it would be subject to high temperatures, such as from
direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
• Remove trim ring from unit,
• Remove 2 transit screws located
on top of the unit.
• Insert the supplied keys into the
slots as shown, and slide the unit
out of the mounting sleeve.
• Install mounting sleeve into
opening, bending tabs to secure.
• Connect wiring harness and
antenna. Consult a qualified
technician if you are unsure.
• Certain vehicles may require an
installation kit and/or wiring
harness adapter (sold separately).
• Test for correct operation and slide
into mounting sleeve to secure.
• Snap trim ring into place.
TYPICAL FRONT-LOAD DIN MOUNTING METHOD
2
XDM7615 INSTALLATION
Wiring Diagram
Antenna Connector
BLACK
Front Preamp Output
Steering Wheel Interface Input
PAC SWI-PS required
BLUE
Subwoofer Preamp Output
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The XDM7615 uses one
10 amp ATM fuse located
beside the wiring connector.
3
XDM7615 OPERATION
Control Locations - Receiver
1
21
4
20
2
3
5
4
19
18
6
7
8
16
17
10
9
15
14
1
Tune/Track Up
12
Eject
2
Mode/Search
13
Auxiliary Input
3
Audio/Setup
14
Open
4
EQ
15
AS/PS/Enter
5
Mute
16
Band
6
Preset 1/Repeat
17
Scan
7
Preset 4/Play/Pause
18
Display
8
Preset 2/Random
19
Reset
9
Preset 5/Folder Down
20
Power
10
Preset 3/Intro
21
Tune/Track Down
11
Preset 6/Folder Up
11
13
12
XDM7615 OPERATION
Control Locations - Remote
1
2
3
4
5
6
21
7
20
8
19
9
18
10
17
11
16
12
13
15
14
1
Mode/Search
12
Scan
2
Volume Up
13
Loudness
3
Power
14
Open
4
Audio/Setup
15
Display
5
Tune/Track Up
16
Mute
6
Volume Down
17
Preset 5/Folder Down
7
AS/PS/Enter
18
Preset 4/Play/Pause
8
Preset 2/Random
19
Preset 1/Repeat
9
Preset 3/Intro
20 Band
10
Preset 6/Folder Up
21 Tune/Track Down
11 EQ
5
XDM7615 OPERATION
General Operation
Front Panel Removal
With the unit off, press EJECT to allow the front panel to
slide down. Gently squeeze the release tab located on the
bottom center underside and pull front panel down and away
from unit to remove. To install, insert left side first, then
push right side to secure.
Power On/Off
Press POWER or any other button (except EJECT or OPEN) to
turn the unit on. Press POWER to turn the unit off.
Mode
Press MODE to select between AM/FM, CD player and
auxiliary input. Modes of operation are shown in the display.
Note: CD mode will not appear unless a CD is inserted.
Auxiliary Input
Insert a 3.5mm connector into the front panel AUX port.
Connect the other end of the 3.5mm connector to the
headphone output of an audio device, MP3 player, etc. Press
MODE to select AUX mode.
Steering Wheel Interface
Input
The steering wheel interface input located on the back of
the head unit allows connection to the Pacific Accessory
Corporation (PAC) SWI-PS interface module (sold separately). Visit www.pac-audio.com for details.
To configure steering wheel controls, follow the instructions
provided with the PAC SWI-PS interface module. After
installing the interface module, insert the module's 3.5mm
jack into the port on the back of the head unit.
Volume
6
Adjust volume using rotary encoder (00-46).
Programmable Turn-On Volume
Press and hold POWER for 2 seconds to program currently
selected volume level. "P-VOL" and the current volume level
will momentarily appear in the display.
Preset EQ Curves
Press EQ to select between POP, JAZZ, CLASSIC, BEAT,
ROCK and OFF (default) equalization curves. Any adjustment
to the Bass or Treble settings automatically cancels the
current EQ curve (if one is selected).
Display
Press DISP to select between clock and different types of
information, such as radio frequency, CD track/elapsed time
or MP3/WMA song information.
Reset
Press RESET upon initial installation or if abnormal
operation occurs. Reset button is located on the front panel.
XDM7615 OPERATION
General Operation - Setup Menu
Set the Clock
With the unit on, press and hold DISP until the clock begins
to adjust the hours
to flash, then release. Press TUNE
and TUNE
to adjust the minutes. Press DISP momentarily to save the selected time.
ll
12/24-hour Clock
Setup Menu
The clock will display 12-hour AM/PM time in USA
frequency spacing mode (PM 10:00). In European frequency
spacing mode, the clock will display 24-hour time (22:00).
Press and hold SETUP for more than 3 seconds to access
the setup menu. Press SETUP momentarily to select
between the menu functions and rotate the rotary encoder
left/right to adjust or activate the desired function.
Menu Function
Options
Loudness Curve
LOUD OFF
LOUD ON
Tuner Frequency FREQ USA
Spacing
FREQ EUR
Clock Display
CLK OFF
CLK ON
Auxiliary Mode
AUX ON
AUX OFF
Beep
BEEP OFF
Confirmation
BEEP ON
Local/Distance
LOC OFF
Tuning
LOC ON
Subwoofer Mode SB-W OFF
SB-W ON
Power on
Message
Demonstration
Mode
nn
MSG OFF
MSG ON
DEMO ON
DEMO OFF
Action
Disables the loudness function.
Enables the loudness function. Activating this feature
will enhance the bass and treble frequencies when
listening to music at low volumes.
Programs the unit to USA tuner spacing.
(200kHz for FM and 10kHz for AM)
Programs the unit to European tuner spacing.
(50kHz for FM and 9kHz for AM)
Programs the unit to not display the clock when the
power is off.
Programs the unit to display the clock when the power
is off.
Enables access to auxiliary mode.
Disables access to auxiliary mode.
Disables the confirmation beep.
Enables the confirmation beep.
Activates Distance tuning.
Activates Local tuning for strong station reception only.
Disables the subwoofer RCA output.
Activates the subwoofer RCA output. Subwoofer control
will be available in the audio menu.
Disables power on message.
Enables power on message to be displayed.
Enables the "BT READY AND IPOD READY" message.
Disables the demonstration mode.
7
XDM7615 OPERATION
General Operation
Audio
Press AUDIO momentarily to select between Volume
(default), Bass, Treble, Balance, Fader and *Subwoofer.
VOLUME
BASS
TREBLE
BALANCE
FADER
*SUBWOOFER
Bass
Press AUDIO until BAS appears then rotate encoder
left/right to adjust ( -6 minimum / +6 maximum).
Treble
Press AUDIO until TRE appears then rotate encoder
left/right to adjust ( -6 minimum / +6 maximum).
Balance
Press AUDIO until BAL appears then rotate encoder
left/right to adjust (BAL L 12-BAL 00-BAL R 12).
BAL 00 represents equal balance
Fader
Press AUDIO until FAD appears then rotate encoder
left/right to adjust (FAD F 12-FAD 00-FAD R 12).
FAD 00 represents equal fader
Subwoofer
Press AUDIO until SUB appears then rotate encoder
left/right to adjust (0 minimum / +12 maximum).
Note:
Subwoofer option must be enabled before it will appear in
the audio menu. Refer to page 7 for details.
Source Audio Memory
Individual Bass and Treble settings are retained in memory
for AM, FM, CD or AUX modes. This allows you to save the
Bass and Treble settings separately for each mode.
Note:
Any adjustment to the Bass or Treble settings automatically
cancels the current EQ curve (if one is selected).
8
XDM7615 OPERATION
Seek Tuning
Manual Tuning
AM/FM Tuner Operation
Press TUNE nn or TUNE ll momentarily to seek the
next strong station.
nn
ll
Press TUNE
or TUNE
for more than 2 seconds,
then release. "MANUAL" will momentarily appear in the
display. Press TUNE
or TUNE
momentarily to
move radio frequency up or down one step at a time. Press
and hold to advance quickly. If tuning is not adjusted for 5
seconds, the unit will return to seek tuning mode (default).
"AUTO" will momentarily appear in the display.
nn
Scan Tuning
Band
ll
Press SCAN to preview strong stations on the current band,
pausing for 5 seconds at each. Press SCAN again to cancel.
Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands.
Storing and Recalling
Station Presets
Up to 18 FM stations and 12 AM stations can be stored. To
store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than
2 seconds. When stored, the preset number will appear in
the display. The station can be recalled anytime by pressing
the corresponding preset button.
Automatically Store
Stations
Press AS/PS for more than 2 seconds to automatically store
the six strongest stations in the current band. Automatic
Local tuning is activated during the initial band scan.
Preset Scan
Press AS/PS for less than 2 seconds to scan presets 1-6 on
the current band, pausing for 5 seconds at each. Press
AS/PS again to cancel.
9
XDM7615 OPERATION
CD Player Operation
Insert CD
Press EJECT to access the CD slot. With the label facing
up, insert a standard size CD into the CD slot. The CD will
automatically begin playback.
Eject CD
Press EJECT to eject the CD. The unit will change to
previous mode of operation (AM, FM or auxiliary input).
If the disc is not removed within 10 seconds, the unit will
reload the disc. The unit does not have to be turned on to
eject CD.
Track Select
Fast Forward and Reverse
Pause
Scan
Repeat
Random
CD-R/CD-RW Compatibility
ll
Press TRACK
to skip to the beginning of the next
track. Press TRACK
to return to the beginning of the
current track. Pressing TRACK
again skips to the
beginning of the previous track.
nn
Press and hold TRACK
or reverse a track.
Press
Press
nn
ll or TRACK nn to fast forward
temporarily stop CD playback.
ll// IIII toagain
to resume playback.
Press INT to play the first 10 seconds of each track.
Press INT again to cancel.
Press RPT to continuously repeat selected track.
Press RPT again to cancel.
Press RDM to play all tracks in random order. Press RDM
again to cancel. Random mode is retained in memory when
selecting between AM/FM tuner, CD player and auxiliary
input modes and when the unit is turned off/on. Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method. In
addition, the following CDs may be incompatible with this
unit:
CDs exposed to extreme temperatures or direct sunlight
for extended periods of time, CDs recorded in which a
recording session failed or a re-recording was attempted
and, or encrypted or copy-protected CDs which do not
conform to the audio CD-DA red book recording standard.
10
XDM7615 OPERATION
CD Player Operation - MP3/WMA Files
Playing an MP3/WMA Disc
When an MP3/WMA encoded disc is first inserted,
“READING” will appear in the display. Depending on the
number of files and folders, this may take several seconds.
Displaying Information
Press DISP to select between track number/elapsed time
(default), clock, track name, directory name, title, artist and
album.
“NO ID3 TAG” will be displayed if the MP3 file contains no
ID3 tag information.
“UNKNOWN” will be displayed if the WMA file contains no WMA tag information.
“ROOT” will be displayed if the directory name of a root
folder is not labeled.
Title Icon This icon will illuminate when the song title is displayed.
Artist Icon This icon will illuminate when the artist name is displayed.
Album Icon This icon will illuminate when the album name is displayed.
Folder Icon This icon will illuminate when the directory name is
displayed.
Character Support
Maximum character display information
• Track name – 32 character maximum
• Directory name – 23 character maximum
• *Song title – 30 character maximum
• *Artist name – 30 character maximum
• *Album name – 30 character maximum
*Song title, Artist Name, and Album name, will only be
displayed if included with the MP3/WMA file.
When referring to MP3/WMA playback, the following terms
are synonymous:
• File name and track name
• Folder name and directory name
11
XDM7615 OPERATION
CD Player Operation - MP3/WMA Files
Refer to the following button function table when selecting, searching or
navigating MP3/WMA files and folders:
Direct File Select
Step 1
Step 2
File/Folder Navigate
Step 1
*
*
Press
to confirm the selected file number or wait for
the input cycle to time out (approximately 5 seconds).
If the file is not available, “NO FILE” will be displayed
momentarily and the current file will continue to play.
Press SEARCH for more than 3 seconds, then release.
Press SEARCH again to navigate files/folders on the disc.
The current folder name will scroll one time followed by
available files and folders.
Step 2
Turn the rotary encoder to preview files/folders in the
current folder. If a folder is selected, the icon will
illuminate.
Step 3
Press
to select the desired file or folder. If a folder is
selected, "/ / " will be displayed. Turn the rotary encoder to
the right to begin searching files in the folder. Step 4
Press
*Folder Access
(Up one level)
12
Press SEARCH for more than 3 seconds, then release.
“MP3 T " or “WMA T ” will flash in the display. Use the
buttons in the above table (3 keystroke maximum input),
or the rotary encoder to enter the desired file number.
to select the desired file within the folder.
When navigating folders (and “/ /“ is displayed), press AUDIO
to access the previous level (up one level).
*Only available on MP3/WMA discs recorded with more than
one folder.
XDM7615 OPERATION
CD Player Operation - MP3/WMA Files
Navigating Note
*Folder Access
After navigating by direct select or file/folder navigate
modes, the track number and elapsed time will be
displayed by default. Press DISP momentarily to select
clock, track name, directory name, title, artist and album.
Press to select the previous folder.
Press to select the next folder.
*Folder access is only available on MP3/WMA discs
recorded with more than one folder.
File Repeat
Press RPT momentarily to continuously repeat selected file.
Press RPT again to cancel.
Folder Repeat
Press RPT for more than 2 seconds to consecutively repeat
all files in the current folder only. The icon will appear
in the display when in folder repeat mode.
Press RPT again to cancel.
Disc Random
Press RDM momentarily to play all files on entire disc in
random order. Press RDM again to cancel.
Folder Random
Disc Intro
Folder Intro
Press RDM for more than 2 seconds to play all files in
current folder only in random order. The icon will
appear in the display when in folder random mode.
Press RDM again to cancel.
Press INT momentarily to play the first 10 seconds of each
file on the entire MP3/WMA disc. Press INT again to cancel.
Press INT for more than 2 seconds to play the first 10
seconds of each file in the current folder only. The icon
will appear in the display when in folder intro mode.
Press INT again to cancel.
Note:
File repeat (current folder only), folder random and folder
intro is only available on MP3/WMA discs recorded with
more than one folder.
13
XDM7615 OPERATION
CD Player Operation - MP3/WMA Files
Media Compatibility
The following types of discs/files are compatible:
• CD-ROM (ISO), CD-R, CD-RW
• CD-DA
• MP3 data
• WMA data
The following types of discs/files are not compatible:
• WMA files that are protected by DRM (Digital Rights Management).
• WMA lossless format
• Discs recorded with Track At Once or packet writing
• MP3 PRO format
• MP3 playlists
• WAV format
Playback Order
Compatible Recording
Formats
MP3/WMA playback sequence is based on recorded order
of files and begins in the root folder of the disc. Any empty
folders or folders that do not include MP3/WMA files are
skipped. This unit may not play files in the order they were
recorded in. Refer to your recording software’s user’s manual
for more information.
• ISO9660 level 1
• ISO9660 level 2
• Yellow Book MODE 1
• Yellow Book MODE 2 FORM 1
• Multi session
• Maximum folders and files - 256
• Maximum folder levels - 8
• MPEG-1/2/2.5 Audio Layer-3
ISO9660 standards:
• Maximum nested folder depth is 8 (including the root folder).
• Valid characters for folder/file names are letters A-Z
(all caps), numbers 0-9, and “_” (underscore). Some
characters may not be displayed correctly, depending on
the character type.
• This device can play back discs in Joliet, Romeo, and other standards that conform to ISO9660. MP3/WMA written in the formats other than the above may not play and/or their file names or folder names may not be displayed properly.
14
XDM7615 OPERATION
CD Player Operation - MP3/WMA Files
Additional MP3/WMA
Information
An internal buffer provides ESP (Electronic Skip Protection) to
virtually eliminate skipping.
When playing a disc recorded with regular audio files
(CD-DA or .WAV) and MP3/WMA files, the unit will play the
MP3/WMA files only.
Only MP3 files with filename extension (.mp3) can be played.
Only WMA files with filename extension (.wma) can be played.
Do not attempt to play discs which contain non-MP3/WMA
files with the MP3/WMA extension.
Sampling Frequency Rates
MP3
WMA
Transfer Bit rates
MP3
WMA
8kHz ~ 48kHz
32kHz ~ 48kHz
32kbps ~ 320kbps constant
Variable bit rates
32kbps ~ 192kbps constant
Variable bit rates
Note:
Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3 Tag Display
Recommended Settings
ID3 tags Version 1.x
This model will not display ID3 Version 2.0 or greater tags.
For best results, use the following settings when burning an
MP3 disc:
128kbps or higher constant bit rate
44.1kHz or higher sampling frequency
For best results, use the following settings when burning a
WMA disc:
64kbps or higher constant bit rate
32kHz or higher sampling frequency
15
XDM7615 WARRANTY
Limited One Year Warranty
This warranty gives you specific legal rights.
You may also have other rights which vary from
state to state.
Dual Electronics Corp. warrants this product to
the original purchaser to be free from defects in
material and workmanship for a period of one
year from the date of the original purchase.
Dual Electronics Corp. agrees, at our option,
during the warranty period, to repair any defect
in material or workmanship or to furnish an
equal new, renewed or comparable product
(whichever is deemed necessary) in exchange
without charges, subject to verification of the
defect or malfunction and proof of the date of
purchase. Subsequent replacement products
are warranted for the balance of the original
warranty period.
Who is covered? This warranty is extended to
the original retail purchaser for products
purchased and used in the U.S.A.
What is covered? This warranty covers all
defects in material and workmanship in this
product. The following are not covered:
installation/removal costs, damage resulting
from accident, misuse, abuse, neglect, product
modification, improper installation, incorrect
line voltage, unauthorized repair or failure to
follow instructions supplied with the product,
or damage occurring during return shipment of
the product.
16
What to do?
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any custom
controls may save you a service call.
2. If you require service during the warranty
period, you must carefully pack the product
(preferably in the original package) and ship
it by prepaid transportation with a copy of the
original receipt from the retailer to an
authorized service center.
3. Please describe your problem in writing and
include your name, a return UPS shipping
address (P.O. Box not acceptable), and a
daytime phone number with your shipment.
4. For more information and for the location of
the nearest authorized service center please
contact us by one of the following methods:
• Call us toll-free at 1-866-382-5476
• E-mail us at cs@dualav.com
Exclusion of Certain Damages: This warranty
is exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability, right,
claim or remedy in contract or tort, whether
or not arising from the company’s negligence,
actual or imputed. No person or representative
is authorized to assume for the company any
other liability in connection with the sale of
this product. In no event shall the company be
liable for indirect, incidental or consequential
damages.
XDM7615 OPERATION
Troubleshooting
Problem
Cause
Action
Yellow wire not connected or incorrect
voltage Red wire not connected or
incorrect voltage
Check connections for proper
voltage (11~16VDC)
Black wire not connected
Check connection to ground
Fuse blown
Replace fuse
Speaker wires not connected
Check connections at speakers
One or more speaker wires touching each
other or touching chassis ground
Insulate all bare speaker wires
from each other and chassis
ground
Yellow or red wire touching chassis
ground
Check for pinched wire
Speaker wires touching chassis ground
Check for pinched wire
Incorrect fuse rating
Use fuse with correct rating
Unit is not mounted correctly or backstrap
is not secure
Check mounting sleeve and
backstrap support
Physical defect in media (CD, CD-R or
CD-RW)
Check media for scratches
ERROR-01 appears on display
Disc read error
Press eject or RESET
ERROR-02 appears on display
Focus error or disc is in upside down
Press eject or RESET
PROTECT appears on display
The WMA file is copy-protected by DRM
(Digital Rights Management)
Write disc using WMA files that
are not copy-protected
NO FILE appears on display
Selected file is not available in direct or
alphanumeric search modes
Repeat search using valid
parameters
The file format is incompatible
Write disc using valid audio
files with .mp3 or .wma file
extensions
CD mechanism position out of alignment
Press and hold EJECT for 3
seconds to reset CD mechanism
position
CD transit screws still in place
emove 2 transit screws located
R
on top of the unit
Unit will not turn on (no power)
Unit has power (but no sound)
Unit blows fuses
Excessive skipping
INVALID appears on display
Unit will not accept a disc
17
XDM7615 OPERATION
Specifications
CD Player
Frequency response: 10Hz-20kHz
Channel separation @ 1kHz: >65dB
D/A converter: 1 Bit
FM Tuner
Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 8.5dBf
50dB quieting sensitivity: 10dBf
Stereo separation @ 1kHz: 40dB
Frequency response: 30Hz-13kHz
AM Tuner
Tuning range: 530kHz-1710kHz
Usable sensitivity: 22uV
Frequency response: 30Hz-2.2kHz
General
Operating voltage: 11-16 VDC, negative ground
Speaker output impedance: 4~8 ohms
Line output voltage: 2 Volts
Dimensions: 7" x 7" x 2" (178 x 178 x 51 mm)
Design and specifications subject to change without notice.
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 17 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms)
18
XDM7615 OPERATION
Notes
19
Dual Electronics Corp.
Toll Free: 1-866-382-5476
www.dualav.com
©2008 Dual Electronics Corp. All rights reserved.
Windows Media and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the
United States and or other countries.
Other trademarks and trade names are those of their respective owners.
NSA0608-V02
Download PDF