Biostar | TP35D2-A7 | User`s manual | Biostar TP35D2-A7 User`s manual

TP35D2-A7 Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Table of Contents
Chapter 1: Introduction ........................................ 1
1.1
1.2
1.3
1.4
1.5
1.6
Before You Start......................................................................................... 1
Package Checklist ..................................................................................... 1
Motherboard Features.............................................................................. 2
Rear Panel Connectors (for Ver 5.x)....................................................... 4
Rear Panel Connectors (for Ver 6.x)....................................................... 4
Motherboard Layout................................................................................. 5
Chapter 2: Hardware Installation .......................... 6
2.1
2.2
2.3
2.4
Installing Central Processing Unit (CPU) ............................................... 6
FAN Headers.............................................................................................. 8
Installing System Memory ........................................................................ 9
Connectors and Slots................................................................................ 11
Chapter 3: Headers & Jumpers Setup .................. 13
3.1
3.2
How to Setup Jumpers............................................................................. 13
Detail Settings .......................................................................................... 13
Chapter 4: OverClock Quick Guide ....................... 20
4.1
4.2
4.3
T-Power Introduction.............................................................................. 20
T-Power BIOS Feature ............................................................................ 20
T-Power Windows Feature..................................................................... 26
Chapter 5: Useful Help ........................................ 32
5.1
5.2
5.3
5.4
Driver Installation Note.......................................................................... 32
Award BIOS Beep Code .......................................................................... 33
Extra Information.................................................................................... 33
Troubleshooting ....................................................................................... 35
Appendencies: SPEC In Other Language .............. 36
German.................................................................................................................. 36
France .................................................................................................................... 38
Italian..................................................................................................................... 40
Spanish ................................................................................................................... 42
Portuguese ............................................................................................................ 44
Polish...................................................................................................................... 46
Russian ................................................................................................................... 48
Arabic..................................................................................................................... 50
Japanese ................................................................................................................ 52
TP35D2-A7
CHAPTER 1: INTRODUCTION
1.1
BEFORE YOU START
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
„
„
„
„
„
„
1.2
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the computer from power outlet
before operation.
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
PACKAGE CHECKLIST
HDD Cable X 1
Serial ATA Cable X 2
Rear I/O Panel for ATX Case X 1
User’s Manual X 1
Fully Setup Driver CD X 1
FDD Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
S/PDIF out Cable X 1 (optional)
Serial ATA Power Cable X 1 (optional)
1
Motherboard Manual
1.3
MOTHERBOARD FEATURES
Ver 5.x
CPU
FSB
Chipset
Ver 6.x
LGA 775
LGA 775
Intel Core2Duo / Core2Quad / Celeron 4xx /
Intel Core2Duo / Core2Quad / Celeron 4xx /
Pentium D / Pentium 4 / Celeron D processor
Pentium D / Pentium 4 / Celeron D processor
Supports Hyper-Threading / Execute Disable Bit / Supports Hyper-Threading / Execute Disable Bit /
Enhanced Intel SpeedStep® / Intel
Enhanced Intel SpeedStep® / Intel
Architecture-64 / Extended Memory 64
Architecture-64 / Extended Memory 64
Technology / Virtualization Technology
Technology / Virtualization Technology
Support 533 / 800 / 1066 / 1333 MHz
Support 533 / 800 / 1066 / 1333 MHz
Intel P35
Intel P35
Intel ICH9
Intel ICH9
ITE 8718F
ITE 8718F
Provides the most commonly used legacy Super Provides the most commonly used legacy Super
Super I/O
Main
Memory
IDE
SATA 2
2
I/O functionality.
I/O functionality.
Low Pin Count Interface
Low Pin Count Interface
Environment Control initiatives,
Environment Control initiatives,
Hardware Monitor Controller
Hardware Monitor Controller
Fan Speed Controller
Fan Speed Controller
ITE's "Smart Guardian" function
ITE's "Smart Guardian" function
DIMM Slots x 4
DIMM Slots x 4
Each DIMM supports 256MB / 512MB / 1GB /
Each DIMM supports 256MB / 512MB / 1GB /
2GB DDR2
2GB DDR2
Max Memory Capicity 8GB
Max Memory Capicity 8GB
Dual Channel Mode DDR2 memory module
Dual Channel Mode DDR2 memory module
Supports DDR2 800 / 667
Supports DDR2 800 / 667
Supports DDR2 533 (with FSB 533/1066 CPU)
Supports DDR2 533 (with FSB 533/1066 CPU)
Registered DIMM and ECC DIMM is not
Registered DIMM and ECC DIMM is not
supported
supported
JMicro JMB368
JMicro JMB368
Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode
supports PIO Mode 0~4
supports PIO Mode 0~4
Integrated Serial ATA Controller
Integrated Serial ATA Controller
Data transfer rates up to 3.0 Gb/s.
Data transfer rates up to 3.0 Gb/s.
SATA Version 2.0 specification compliant
SATA Version 2.0 specification compliant
TP35D2-A7
Ver 5.x
Ver 6.x
Realtek RTL 8110SC / 8100C (optional)
LAN
Sound
Codec
10 / 100 Mb/s / 1Gb/s auto negotiation (Gigabit 10 / 100 Mb/s / 1Gb/s auto negotiation (Gigabit
bandwidth is for RTL 8110SC only)
bandwidth is for RTL 8110SC only)
Half / Full duplex capability
Half / Full duplex capability
ALC888
ALC861VD
7.1 channels audio out
5.1 channels audio out
High Definition Audio
PCI slot
Slots
On Board
Connector
Realtek RTL 8110SC / 8100C (optional)
High Definition Audio
x3
PCI slot
x3
PCI Express x 16 slot
x1
PCI Express x 16 slot
x1
PCI Express x 4 slot
x1
PCI Express x 4 slot
x1
PCI Express x 1 slot
x1
PCI Express x 1 slot
x1
Floppy connector
x1
Floppy connector
x1
Printer Port Connector
x1
Printer Port Connector
x1
IDE Connector
x1
IDE Connector
x1
SATA Connector
x4
SATA Connector
x4
Front Panel Connector
x1
Front Panel Connector
x1
Front Audio Connector
x1
Front Audio Connector
x1
CD-in Connector
x1
CD-in Connector
x1
S/PDIF out connector
x1
S/PDIF out connector
x1
S/PDIF in connector(optional)
x1
S/PDIF in connector(optional)
x1
CPU Fan header
x1
CPU Fan header
x1
System Fan header
x2
System Fan header
x2
Clear CMOS header
x1
Clear CMOS header
x1
USB connector
x3
USB connector
x3
Power Connector (24pin)
x1
Power Connector (24pin)
x1
Power Connector (4pin)
x1
Power Connector (4pin)
x1
PS/2 Keyboard
x1
PS/2 Keyboard
x1
PS/2 Mouse
x1
PS/2 Mouse
x1
Back Panel Serial Port
x1
Serial Port
x1
I/O
x1
LAN port
x1
USB Port
x6
USB Port
x6
Audio Jack
x6
Audio Jack
x3
Board Size
LAN port
220 (W) x 305 (L) mm
220 (W) x 305 (L) mm
Windows 2000 / XP / VISTA
Windows 2000 / XP / VISTA
OS Support Biostar Reserves the right to add or remove
support for any OS with or without notice
Biostar Reserves the right to add or remove
support for any OS with or without notice
3
Motherboard Manual
1.4
REAR PANEL CONNECTORS (FOR VER 5.X)
PS/2
Mouse
PS/ 2
Keyboard
LAN
COM1
USBX2
USBX2
Center
1.5
Audio Jack
USBX2
Line In
Rear
Line Out
Side
Mic In
REAR PANEL CONNECTORS (FOR VER 6.X)
PS/2
Mouse
LAN
Line In/
Surround
Line Out
Mic I n 1/
Bass/ Center
PS/ 2
Keyboard
4
COM1
USBX2
USBX2
USBX2
TP35D2-A7
1.6
MOTHERBOARD LAYOUT
JCFAN1
JKBMS1
LGA775
JPRNT1
JCOM1
CPU1
JRJ45USB1
DDR2_B2
DDR2_B1
JUSB1
DDR2_A2
DDR2_A1
JUSB2
Intel
P35
JATXPWR1
JAUDIO1
(for Ver 5.x)
JAUDIO2
(for Ver 6.x)
JATXPWR2
JNFAN1
PEX16_1
Super
I/O
Intel
ICH9
PEX4_1
JCMOS1
BAT1
PEX1_1
JSFAN1
LAN
PCI1
SATA3
SATA1
SATA4
SATA2
BIOS
PCI2
IDE
CODEC
IDE1
PCI3
LED2
RSTSW2
JSPDIF_OUT1
LED1
FDD1
JAUDIOF1
JCDIN1
JSPDIF_IN1(optional)
JUSB5
JUSB4
JUSB3
J PANEL1
PWRSW1
Note: ■ represents the 1st pin.
5
Motherboard Manual
CHAPTER 2: HARDWARE INSTALLATION
2.1
INSTALLING CENTRAL PROCESSING UNIT (CPU)
Special Notice:
Remove Pin Cap before installation, and make good preservation
for future use. When the CPU is removed, cover the Pin Cap on the
empty socket to ensure pin legs won’t be damaged.
Pin Cap
Step 1: Pull the socket locking lever out from the socket and then raise
the lever up to a 90-degree angle.
6
TP35D2-A7
Step 2: Look for the triangular cut edge on socket, and the golden dot on
CPU should point forwards this triangular cut edge. The CPU will
fit only in the correct orientation.
Step 2-1:
Step 2-2:
Step 3: Hold the CPU down firmly, and then lower the lever to locked
position to complete the installation.
Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it
on the retention frame. Connect the CPU FAN power cable into
the JCFAN1. This completes the installation.
7
Motherboard Manual
2.2
FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
JCFAN1: CPU Fan Header
4
Pin
1
2
3
1
4
Assignment
Ground
+12V
FAN RPM rate
sense
Smart Fan
Control
JSFAN1: System Fan Header
JNFAN1: Northbridge Fan Header
1
3
Pin
JNFAN1
1
2
3
Assignment
Ground
+12V
FAN RPM rate
sense
1
3
JSFAN1
Note:
The JNFAN1 and JSFAN1 support 3-pin head connector. When connecting with wires
onto connectors, please note that the red wire is the positive and should be connected to
pin#2, and the black wire is Ground and should be connected to GND.
8
TP35D2-A7
2.3
INSTALLING SYSTEM MEMORY
DDR2_B1
DDR2_B2
DDR2_A1
DDR2_A2
A. Memory Modules
1.
Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2.
Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
B. Memory Capacity
DIMM Socket
Location
DDR Module
DDR2_A1
256MB/512MB/1GB/2GB
DDR2_A2
256MB/512MB/1GB/2GB
DDR2_B1
256MB/512MB/1GB/2GB
DDR2_B2
256MB/512MB/1GB/2GB
Total Memory
Size
Max is 8GB.
9
Motherboard Manual
C. Dual Channel Memory installation
To trigger the Dual Channel function of the motherboard, the memory module
must meet the following requirements:
Install memory module of the same density in pairs, shown in the following
table.
Dual Channel Status DDR2_A1 DDR2_A2 DDR2_B1 DDR2_B2
Enabled
O
X
O
X
Enabled
X
O
X
O
Enabled
O
O
O
O
(O means memory installed, X means memory not installed.)
The DRAM bus width of the memory module must be the same (x8 or
x16)
10
TP35D2-A7
2.4
CONNECTORS AND SLOTS
FDD1: Floppy Disk Connector
The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cables.
33
1
34
2
IDE1: Hard Disk Connector
The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.
The IDE connector can connect a master and a slave drive, so you can connect
up to two hard disk drives.
39
1
40
2
11
Motherboard Manual
PEX16_1: PCI-Express x16 Slot
-
PCI-Express 1.0a compliant.
Maximum theoretical realized bandwidth of 4GB/s simultaneously per
direction, for an aggregate of 8GB/s totally.
PEX4_1: PCI-Express x4 Slot
-
PCI-Express 1.0a compliant.
Maximum theoretical realized bandwidth of 1GB/s simultaneously per
direction, for an aggregate of 2GB/s totally.
PEX1_1: PCI-Express Slot
-
PCI-Express 1.0a compliant.
Maximum theoretical realized bandwidth of 250MB/s simultaneously per
direction, for an aggregate of 500MB/s totally.
PEX16_1
PEX4_1
PEX1_1
PCI1~PCI3: Peripheral Component Interconnect Slots
This motherboard is equipped with 3 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.
PCI1
PCI2
PCI3
12
TP35D2-A7
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1
HOW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.
Pin opened
3.2
Pin closed
Pin1-2 closed
DETAIL SETTINGS
JPANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep
button and speaker connection. It allows user to connect the PC case’s front
panel switch functions.
HLED
RST
SPK
+ ++ -
8
16
1
9
On/Off
SLP
PWR_LED
Pin
1
2
3
4
5
6
7
8
Assignment
+5V
N/A
N/A
Speaker
HDD LED (+)
HDD LED (-)
Ground
Reset control
Function
Speaker
Connector
Hard drive
LED
Reset button
Pin
9
10
11
12
13
14
15
16
Assignment
Sleep control
Ground
N/A
Power LED (+)
Power LED (+)
Power LED (-)
Power button
Ground
Function
Sleep button
N/A
Power LED
Power-on button
13
Motherboard Manual
JATXPWR2: ATX Power Source Connector
JATXPW2 allows user to connect 24-pin power connector on the ATX power
supply.
13
1
24
12
Pin
Assignment
Pin
Assignment
13
14
15
16
17
18
19
20
21
22
23
24
+3.3V
-12V
Ground
PS_ON
Ground
Ground
Ground
NC
+5V
+5V
+5V
Ground
1
2
3
4
5
6
7
8
9
10
11
12
+3.3V
+3.3V
Ground
+5V
Ground
+5V
Ground
PW_OK
Standby Voltage+5V
+12V
+12V
+3.3V
JATXPWR1: ATX Power Source Connector
By connecting this connector, it will provide +12V to CPU power circuit.
14
2
1
3
4
Pin
1
2
3
4
Assignment
+12V
+12V
Ground
Ground
TP35D2-A7
JUSB3/JUSB4/JUSB5: Headers for USB 2.0 Ports at Front Panel
This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.
Pin
1
2
3
4
5
6
7
8
9
10
JUSB5
JUSB4
JUSB3
9
1
10
2
Assignment
+5V (fused)
+5V (fused)
USBUSBUSB+
USB+
Ground
Ground
Key
NC
JAUDIOF1: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel. It will disable the output on back panel audio connectors.
9
1
10
2
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
Mic Left in
Ground
Mic Right in
GPIO
Right line in
Jack Sense
Front Sense
Key
Left line in
Jack Sense
JCDIN1: CD-ROM Audio-in Connector
This connector allows user to connect the audio source from the variaty devices,
like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc..
Pin
1
2
3
4
4
Assignment
Left Channel Input
Ground
Ground
Right Channel
Input
1
15
Motherboard Manual
JCMOS1: Clear CMOS Header
By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting
and the CMOS data, please carefully follow the procedures to avoid damaging
the motherboard.
3
1
Pin 1-2 Close:
Normal Operation (default).
3
3
1
1
Pin 2-3 Close:
Clear CMOS data.
※ Clear CMOS Procedures:
1.
2.
3.
4.
5.
6.
Remove AC power line.
Set the jumper to “Pin 2-3 close”.
Wait for five seconds.
Set the jumper to “Pin 1-2 close”.
Power on the AC.
Reset your desired password or clear the CMOS data.
SATA1~SATA4: Serial ATA Connectors
The motherboard has a PCI to SATA Controller with 4 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.
SATA3 SATA1
SATA4 SATA2
7
16
4
1
Pin
1
2
3
4
5
6
7
Assignment
Ground
TX+
TXGround
RXRX+
Ground
TP35D2-A7
JSPDIF_OUT1: Digital Audio-out Connector
This connector allows user to connect the PCI bracket SPDIF output header.
Pin
1
2
3
3
Assignment
+5V
SPDIF_OUT
Ground
1
JSPDIF_IN1: Digital Audio-in Connector (Optional)
This connector allows user to connect the PCI bracket SPDIF input header.
Pin
1
2
3
3
Assignment
+5V
SPDIF_IN
Ground
1
17
Motherboard Manual
On-Board LED Indicators
There are 2 LED indicators on the motherboard to show system status.
LED2
LED1
LED1 and LED2:
These 2 LED indicate system power on diagnostics.
Please refer to the table below for different messages:
LED1
ON
ON
OFF
OFF
LED2
ON
OFF
ON
OFF
Message
Normal
Memory Error
VGA Error
Abnormal: CPU / Chipset error.
On-Board Buttons
There are 2 on-board buttons.
RSTSW2
PWRSW1
PWRSW1:
This is an on-board Power Switch button.
RSTSW2:
This is an on-board Reset button.
18
TP35D2-A7
JPRNT1: Printer Port Connector
This header allows you to connector printer on the PC.
25
2
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
Assignment
-Strobe
-ALF
Data 0
-Error
Data 1
-Init
Data 2
-Scltin
Data 3
Ground
Data 4
Ground
Data 5
1
Pin
14
15
16
17
18
19
20
21
22
23
24
25
26
Assignment
Ground
Data 6
Ground
Data 7
Ground
-ACK
Ground
Busy
Ground
PE
Ground
SCLT
Key
19
Motherboard Manual
CHAPTER 4: OVERCLOCK QUICK GUIDE
4.1
T-POWER INTRODUCTION
Biostar T-Power is a whole new utility that is designed for overclock users.
Based on many precise tests, Biostar Engineering Team (BET) has
developed this ultimate overclock engine to raise system performance.
No matter whether under BIOS or Windows interface, T-Power is able to
present the best system state according to users’ overclock setting.
T-Power BIOS Features:
Overclocking Navigator Engine (O.N.E.)
CMOS Reloading Program (C.R.P.)
Memory Integration Test (M.I.T., under Overclock Navigator Engine)
Integrated Flash Program (I.F.P.)
Self Recovery System (S.R.S)
T-Power Windows Feature:
Hardware Monitor
Overclock Engine
System Information
!! WARNING !!
For better system performance, the BIOS firmware is being
continuously updated. The BIOS information described below in
this manual is for your reference only and the actual BIOS
information and settings on board may be different from this
manual. For further information of setting up the BIOS, please
refer to the BIOS Manual in the Setup CD.
20
TP35D2-A7
4.2
T-POWER BIOS FEATURE
A. Overclocking Navigator Engine (O.N.E.):
ONE provides two powerful overclocking engines: MOS and AOS for both
Elite and Casual overclockers.
Manual Overclock System (M.O.S.)
MOS is designed for experienced overclock users.
It allows users to customize personal overclock settings.
21
Motherboard Manual
CPU Clock Ratio & CPU Clock:
CPU Clock Ratio x CPU Clock = CPU Frequency. CPU Frequency is
directly in proportion to system performance. To maintain the system
stability, CPU voltage needs to be increased also when raising CPU
frequency.
PCI-E Clock Select:
It helps to increase VGA card performance.
System Me mory Frequency:
To get better system performance, sometimes downgrading the memory
frequency is necessary when CPU frequency is adjusted over the upper
limit.
CPU Voltage:
This function will increase CPU stability when overclocking. However, the
CPU temperature will increase when CPU voltage is increased.
(G)MCH Voltage:
This function lets you select the (G)MCH voltage.
FSB Termination Voltage:
This function will increase chipset stability when overclocking.
Memory Voltage:
This function will increase memory stability when overclocking.
Automatic Overclock System (A.O.S.)
For beginners in overclock field, BET had developed an easy, fast, and
powerful feature to increase the system performance, named A.O.S.
Based on many tests and experiments, A.O.S. provides 3 ideal overclock
configurations that are able to raise the system performance in a single
step.
22
TP35D2-A7
V6 Tech Engine:
This setting will raise about 10%~15% of whole system performance.
V8 Tech Engine:
This setting will raise about 15%~25% of whole system performance.
V12 Tech Engine:
This setting will raise about 25%~30% of whole system performance.
23
Motherboard Manual
B. CMOS Reloading Program (C.R.P.):
It allows users to save different CMOS settings into BIOS-ROM.
Users are able to reload any saved CMOS setting for customizing system
configurations.
Moreover, users are able to save an ideal overclock setting during overclock
operation.
There are 50 sets of record addresses in total, and users are able to name the
CMOS data according to personal preference.
24
TP35D2-A7
C. Memory Integration Test (M.I.T.):
This function is under “Overclocking Navigator Engine” item.
MIT allows users to test memory compatibilities, and no extra devices or
software are needed.
Step 1:
The default setting under this item is “Disabled”; the condition parameter should
be changed to “Enable” to proceed this test.
↓
Step 2:
Save and Exit from CMOS setup and reboot the system to activate this test.
Run this test for 5 minutes (minimum) to ensure the memory stability.
Step 3:
When the process is done, change the setting back from “Enable” to “Disable”
to complete the test.
25
Motherboard Manual
D. Self Recovery System (S.R.S.):
This function can’t be seen under T-Power BIOS setup; and is always on
whenever the system starts up.
However, it can prevent system hang-up due to inappropriate overclock
actions.
When the system hangs up, S.R.S. will automatically log in the default BIOS
setting, and all overclock settings will be re-configured.
E. Integrated Flash Program (I.F.P.):
IFP is a safe and quick way to upgrade BIOS.
Step 1:
Go to Biostar website (http://www.biostar.com.tw) to download the latest BIOS
file. Then, save the file into a floppy disk.
Step 2:
Insert the floppy disk and reboot the system to get into CMOS screen.
Step 3:
Select the item “Integrated Flash Program” to get the following frame and
choose the BIOS file downloaded in step 1.
Step 4:
Press “Enter” key to start BIOS file loading, and BIOS updating will process
automatically.
Step 5:
When the BIOS update is completed, press YES to the message “Flash done,
Reset system”, and the system will reboot automatically to finish the process.
Advise:
You can update the system BIOS by simply pressing “Enter” key for three times.
26
TP35D2-A7
4.3
T-POWER WINDOWS FEATURE
1. Desktop Icon
After the T-Utility has been installed, a T-Utility icon will appear on the
desktop, just like the icon shown below.
Now you can launch the T-Utility simply by double-clicking the desktop
icon.
2. Main Panel
If you double-click the desktop icon, T-Utility will be launched. Please
refer to the following figure; the utility’s first window you will see is
Main Panel.
Main Panel contains features as follows:
a.
b.
Display the CPU Speed, CPU external clock, Memory clock, VGA
clock, and PCI clock information.
Contains About, Overclock/Overvoltage, and Hardware Monitor
Buttons for invoking respective panels. The On/Off button is for
closing the program.
27
Motherboard Manual
3. Overclock/Overvoltage Panel
Click the Overclock/Overvoltage button in the Main Panel, the button
will be highlighted and the Overclock/Overvoltage Panel will show
up as the following figure. As you can see, the Overclock Panel is
on the upper side, and the Overvoltage Panel is on the lower side.
28
TP35D2-A7
Overclock Panel contains these features:
a.
“Auto-Overclock”:
User can click this button and T-Utility will set the best and stable
performance and frequency automatically. A warning dialog as
below will show up to notify you that the system may become
unstable, click on “OK” to continue.
Then T-Utility will execute a series of testing until system fail.
Then system will do fail-safe reboot by using Watchdog function.
After reboot, launch the T-Utility again and the utility will load the
previously verified best and stable frequency.
b.
“Verify”:
If you use the “Manual Adjust” bar to adjust the CPU frequency,
then you can click this button and T-Utility will proceed a testing for
current frequency. If the testing is ok, then the current frequency
will be saved into system registry. If the testing fails, system will do
a fail-safe rebooting. After reboot, the T-Utility will restore to the
hardware default setting.
Warning:
Manually overclock is potentially dangerous, especially when the
overclocking percentage is over 110 %. We strongly recommend you
verify every speed you overclock by click the Verify button. Or, you can
just click Auto overclock button and let T-Utility automatically gets the
best result for you.
c.
“V3 Engine”/“V6 Engine”/“V9 Engine”:
Provide user the ability to do real-time overclock adjustment.
d.
“Recovery”:
Click this button and the T-Utility will restore all values to the
hardware default setting.
29
Motherboard Manual
e. “Save / Open Setting”:
Click Save button to save current setting to a file, and click Open
button to load a previously saved setting.
f.
“Panel Color”:
Click this button to change the color of the panel.
Overvoltage Panel contains these features:
a.
b.
c.
“CPU Voltage”:
This function allows user to adjust CPU voltage.
increase or “-“ to decrease the CPU voltage.
Click on “+” to
“Memory Voltage”:
This function allows user to adjust Memory voltage.
to increase or “-“ to decrease the Memory voltage.
Click on “+”
“Chipset Voltage”:
This function allows user to adjust Chipset voltage.
to increase or “-“ to decrease the Chipset voltage.
Click on “+”
4. Hardware Monitor Panel
Click the Hardware Monitor button in Main Panel, the button will be
highlighted and the Hardware Monitor panel will show up as the
following figure.
In this panel, you can get the real-time status information of your
system. The information will be refreshed every 1 second.
30
TP35D2-A7
5. About Panel
Click the “about” button in Main Panel, the button will be highlighted
and the About Panel will show up as the following figure.
In this panel, you can get model name and detail information in hints
of all the chipset that are related to overclocking. You can also get
the the version number of T-Utility.
Note:
Because the overclock, overvoltage, and hardware monitor features
are controlled by several separate chipset, T-Utility divides these
features to separate panels. If one chipset is not on board, the
correlative button in Main panel will be disabled, but it will not
interfere with other panels’ functions. This property can make
T-Utility more robust.
31
Motherboard Manual
CHAPTER 5: USEFUL HELP
5.1
DRIVER INSTALLATION NOTE
After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.
You will see the following window after you insert the CD
The setup guide will auto detect your motherboard and operating system.
Note:
If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep2.html
32
TP35D2-A7
5.2
AWARD BIOS BEEP CODE
Beep Sound
Meaning
One long beep followed by two short
beeps
High-low siren sound
Video card not found or video card
memory bad
CPU overheated
System will shut down automatically
One Short beep when system boot-up
Long beeps every other second
No error found during POST
No DRAM detected or install
5.3
EXTRA INFORMATION
A. BIOS Update
After you fail to update BIOS or BIOS is invaded by virus, the
Boot-Block function will help to restore BIOS. If the following message
is shown after boot-up the system, it means the BIOS contents are
corrupted.
In this Case, please follow the procedure below to restore the BIOS:
1. Make a bootable floppy disk.
2. Download the Flash Utility “AWDFLASH.exe” from the Biostar
website: www.biostar.com.tw
3. Confirm motherboard model and download the respectively BIOS
from Biostar website.
4. Copy “AWDFLASH.exe” and respectively BIOS into floppy disk.
5. Insert the bootable disk into floppy drive and press Enter.
6. System will boot-up to DOS prompt.
7. Type “Awdflash xxxx.bf/sn/py/r” in DOS prompt.
(xxxx means BIOS name.)
8. System will update BIOS automatically and restart.
9. The BIOS has been recovered and will work properly.
33
Motherboard Manual
B. CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
34
TP35D2-A7
5.4
TROUBLESHOOTING
Probable
Solution
1.
No power to the system at all
1.
Make sure power cable is
Power light don’t illuminate, fan
securely plugged in.
inside power supply does not turn 2.
Replace cable.
on.
3.
Contact technical support.
2.
Indicator light on keyboard does
not turn on.
System inoperative. Keyboard lights
Using even pressure on both ends of
are on, power indicator lights are lit,
the DIMM, press down firmly until the
and hard drive is spinning.
module snaps into place.
System does not boot from hard disk
1.
Check cable running from disk to
drive, can be booted from optical drive.
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2.
Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
System only boots from optical drive.
1.
Back up data and applications
Hard disk can be read and applications
files.
can be used but booting from hard disk 2.
Reformat the hard drive.
is impossible.
Re-install applications and data
using backup disks.
Screen message says “Invalid
Review system’s equipment. Make sure
Configuration” or “CMOS Failure.”
correct information is in setup.
Cannot boot system after installing
1.
Set master/slave jumpers
second hard drive.
correctly.
2.
Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.
35
Motherboard Manual
APPENDENCIES: SPEC IN OTHER LANGUAGE
GERMAN
Ver 5.x
Ver 6.x
LGA 775
LGA 775
Intel Core2Duo / Core2Quad / Celeron 4xx /
Intel Core2Duo / Core2Quad / Celeron 4xx /
Pentium 4 / Pentium D / Celeron D Prozessoren Pentium 4 / Pentium D / Celeron D Prozessoren
CPU
FSB
Chipsatz
Super E/A
Unterstützt Hyper-Threading / Execute Disable Unterstützt Hyper-Threading / Execute Disable
Bit / Enhanced Intel SpeedStep® / Intel
Bit / Enhanced Intel SpeedStep® / Intel
Architecture-64 / Extended Memory 64
Architecture-64 / Extended Memory 64
Technology / Virtualization Technology
Technology / Virtualization Technology
533 / 800 / 1066 / 1333 MHz
533 / 800 / 1066 / 1333 MHz
Intel P35
Intel P35
Intel ICH9
Intel ICH9
ITE 8718F
ITE 8718F
Bietet die häufig verwendeten alten Super
Bietet die häufig verwendeten alten Super
E/A-Funktionen.
E/A-Funktionen.
Low Pin Count-Schnittstelle
Low Pin Count-Schnittstelle
Umgebungskontrolle,
Umgebungskontrolle,
Hardware-Überwachung
Hardware-Überwachung
Lüfterdrehzahl-Controller/-Überwachung
Lüfterdrehzahl-Controller/-Überwachung
"Smart Guardian"-Funktion von ITE
"Smart Guardian"-Funktion von ITE
DDR2 DIMM-Steckplätze x 4
DDR2 DIMM-Steckplätze x 4
Jeder DIMM unterstützt 256MB / 512MB / 1GB / Jeder DIMM unterstützt 256MB / 512MB / 1GB /
Arbeitsspeich
er
2GB DDR2.
2GB DDR2.
Max. 8GB Arbeitsspeicher
Max. 8GB Arbeitsspeicher
Dual-Kanal DDR2 Speichermodul
Dual-Kanal DDR2 Speichermodul
Unterstützt DDR2 800 / 667
Unterstützt DDR2 800 / 667
Unterstützt DDR2 533 (w. FSB 533/1066 CPU) Unterstützt DDR2 533 (w. FSB 533/1066 CPU)
IDE
SATA
registrierte DIMMs. ECC DIMMs werden nicht
registrierte DIMMs. ECC DIMMs werden nicht
unterstützt.
unterstützt.
JMicro JMB368
JMicro JMB368
Ultra DMA 33 / 66 / 100 / 133 Bus
Ultra DMA 33 / 66 / 100 / 133 Bus
Master-Modus
Master-Modus
Unterstützt PIO-Modus 0~4,
Unterstützt PIO-Modus 0~4,
Integrierter Serial ATA-Controller
Integrierter Serial ATA-Controller
Datentransferrate bis zu 3.0Gb/s
Datentransferrate bis zu 3.0Gb/s
Konform mit der SATA-Spezifikation Version 2.0. Konform mit der SATA-Spezifikation Version 2.0.
LAN
36
Realtek RTL 8110SC / RTL 8100C(optional)
Realtek RTL 8110SC / RTL 8100C(optional)
10 / 100 / 1000 Mb/s Auto-Negotiation
10 / 100 / 1000 Mb/s Auto-Negotiation
TP35D2-A7
Ver 5.x
Ver 6.x
(Gigabit-Bandbreite nur beim RTL 8110SC)
HD
Halb-/ Vollduplex-Funktion
ALC888
ALC861VD
Unterstützt High-Definition Audio
Audio-Unters Unterstützt High-Definition Audio
tützung
Onboard-Ans
chluss
x3
PCI-Steckplatz
x3
PCI Express x16 Steckplatz
x1
PCI Express x16 Steckplatz
x1
PCI Express x4 Steckplatz
x1
PCI Express x4 Steckplatz
x1
PCI Express x 1-Steckplatz
x1
PCI Express x 1-Steckplatz
x1
Diskettenlaufwerkanschluss
x1
Diskettenlaufwerkanschluss
x1
Druckeranschluss Anschluss
x1
Druckeranschluss Anschluss
x1
IDE-Anschluss
x1
IDE-Anschluss
x1
SATA-Anschluss
x4
SATA-Anschluss
x4
Fronttafelanschluss
x1
Fronttafelanschluss
x1
Front-Audioanschluss
x1
Front-Audioanschluss
x1
CD-IN-Anschluss
x1
CD-IN-Anschluss
x1
S/PDIF- Ausgangsanschluss
x1
S/PDIF- Ausgangsanschluss
x1
S/PDIF Eingangsanschluss(optional) x1
S/PDIF Eingangsanschluss(optional) x1
CPU-Lüfter-Sockel
x1
CPU-Lüfter-Sockel
System-Lüfter-Sockel
x2
System-Lüfter-Sockel
x2
"CMOS löschen"-Sockel
x1
"CMOS löschen"-Sockel
x1
USB-Anschluss
x3
USB-Anschluss
x3
Stromanschluss (24-polig)
x1
Stromanschluss (24-polig)
x1
Stromanschluss (4-polig)
x1
Stromanschluss (4-polig)
x1
PS/2-Tastatur
x1
PS/2-Tastatur
x1
PS/2-Maus
x1
PS/2-Maus
x1
x1
Serieller Anschluss
x1
LAN-Anschluss
x1
LAN-Anschluss
x1
USB-Anschluss
x6
USB-Anschluss
x6
Audioanschluss
x6
Audioanschluss
x3
Rückseiten-E Serieller Anschluss
/A
5.1-Kanal-Audioausgabe
7.1-Kanal-Audioausgabe
PCI-Steckplatz
Steckplätze
(Gigabit-Bandbreite nur beim RTL 8110SC)
Halb-/ Vollduplex-Funktion
x1
Platinengröße 220 mm (B) X 305 mm (L)
220 mm (B) X 305 mm (L)
Windows 2000 / XP / VISTA
Windows 2000 / XP / VISTA
Biostar behält sich das Recht vor, ohne
Biostar behält sich das Recht vor, ohne
Ankündigung die Unterstützung für ein
Ankündigung die Unterstützung für ein
Betriebssystem hinzuzufügen oder zu
Betriebssystem hinzuzufügen oder zu
entfernen.
entfernen.
OS-Unterstüt
zung
37
Motherboard Manual
FRANCE
Ver 5.x
Ver 6.x
LGA 775
LGA 775
Processeurs Intel Core2Duo / Core2Quad /
Processeurs Intel Core2Duo / Core2Quad /
Celeron 4xx / Pentium 4 / Pentium D / Celeron D Celeron 4xx / Pentium 4 / Pentium D / Celeron D
UC
Prend en charge les technologies
Prend en charge les technologies
Hyper-Threading / d'exécution de bit de
Hyper-Threading / d'exécution de bit de
désactivation / Intel SpeedStep® optimisée/
désactivation / Intel SpeedStep® optimisée/
d'architecture Intel 64 / de mémoire étendue 64 d'architecture Intel 64 / de mémoire étendue 64
/ de virtualisation
Bus frontal 533 / 800 / 1066 / 1333 MHz
Chipset
Super E/S
Mémoire
principale
IDE
SATA
38
/ de virtualisation
533 / 800 / 1066 / 1333 MHz
Intel P35
Intel P35
Intel ICH9
Intel ICH9
ITE 8718F
ITE 8718F
Fournit la fonctionnalité de Super E/S
Fournit la fonctionnalité de Super E/S
patrimoniales la plus utilisée.
patrimoniales la plus utilisée.
Interface à faible compte de broches
Interface à faible compte de broches
Initiatives de contrôle environnementales,
Initiatives de contrôle environnementales,
Moniteur de matériel
Moniteur de matériel
Contrôleur /moniteur de vitesse de ventilateur
Contrôleur /moniteur de vitesse de ventilateur
Fonction "Gardien intelligent" de l'ITE
Fonction "Gardien intelligent" de l'ITE
Fentes DDR2 DIMM x 4
Fentes DDR2 DIMM x 4
Chaque DIMM prend en charge des DDR2 de
Chaque DIMM prend en charge des DDR2 de
256Mo / 512Mo / 1Go / 2Go
256Mo / 512Mo / 1Go / 2Go
Capacité mémoire maximale de 8Go
Capacité mémoire maximale de 8Go
Module de mémoire DDR2 à mode à double voie Module de mémoire DDR2 à mode à double voie
Prend en charge la DDR2 800 / 667
Prend en charge la DDR2 800 / 667
Prend en charge la DDR2 533 (w. FSB 533/1066 Prend en charge la DDR2 533 (w. FSB 533/1066
CPU)
CPU)
Les DIMM à registres et DIMM avec code
Les DIMM à registres et DIMM avec code
correcteurs d'erreurs ne sont pas prises en
correcteurs d'erreurs ne sont pas prises en
charge
charge
JMicro JMB368
JMicro JMB368
Mode principale de Bus Ultra DMA 33 / 66 / 100 / Mode principale de Bus Ultra DMA 33 / 66 / 100 /
133
133
Prend en charge le mode PIO 0~4,
Prend en charge le mode PIO 0~4,
Contrôleur Serial ATA intégré :
Contrôleur Serial ATA intégré :
Taux de transfert jusqu'à 3.0Go/s.
Taux de transfert jusqu'à 3.0Go/s.
Conforme à la spécification SATA Version 2.0
Conforme à la spécification SATA Version 2.0
TP35D2-A7
Ver 5.x
Ver 6.x
Realtek RTL 8110SC / RTL 8100C(optional)
Realtek RTL 8110SC / RTL 8100C(optional)
10 / 100 / 1000 Mb/s négociation automatique 10 / 100 / 1000 Mb/s négociation automatique
(La bande passante Gigabit est pour le RTL
(La bande passante Gigabit est pour le RTL
8110SC uniquement)
8110SC uniquement)
Half / Full duplex capability
Half / Full duplex capability
Prise en
ALC888
ALC861VD
charge
Prise en charge de l'audio haute définition
Prise en charge de l'audio haute définition
audio HD
Sortie audio à 7.1 voies
Sortie audio à 5.1 voies
LAN
Fentes
Connecteur
embarqué
Fente PCI
x3
Fente PCI
Fente PCI Express x16
x1
Fente PCI Express x16
x1
Fente PCI Express x4
x1
Fente PCI Express x4
x1
Fente PCI Express x1
x1
Fente PCI Express x1
x1
Connecteur de disquette
x1
Connecteur de disquette
x1
Connecteur de Port d'imprimante
x1
Connecteur de Port d'imprimante
x1
Connecteur IDE
x1
Connecteur IDE
x1
Connecteur SATA
x4
Connecteur SATA
x4
Connecteur du panneau avant
x1
Connecteur du panneau avant
x1
Connecteur Audio du panneau avant x1
Connecteur Audio du panneau avant x1
Connecteur d'entrée CD
x1
Connecteur d'entrée CD
x1
Connecteur de sortie S/PDIF
x1
Connecteur de sortie S/PDIF
x1
Connecteur d'entrée S/PDIF(en option) x1
Connecteur d'entrée S/PDIF(en option) x1
Embase de ventilateur UC
x1
Embase de ventilateur UC
x1
Embase de ventilateur système
x2
Embase de ventilateur système
x2
Embase d'effacement CMOS
x1
Embase d'effacement CMOS
x1
Connecteur USB
x3
Connecteur USB
x3
Connecteur d'alimentation
x1
Connecteur d'alimentation
x1
(24 broches)
Connecteur d'alimentation
(24 broches)
x1
(4 broches)
E/S du
panneau
arrière
Dimensions
de la carte
x3
Connecteur d'alimentation
x1
(4 broches)
Clavier PS/2
x1
Clavier PS/2
x1
Souris PS/2
x1
Souris PS/2
x1
Port série
x1
Port série
x1
Port LAN
x1
Port LAN
x1
Port USB
x6
Port USB
x6
Fiche audio
x6
Fiche audio
x3
220 mm (l) X 305 mm (H)
220 mm (l) X 305 mm (H)
Windows 2000 / XP / VISTA
Windows 2000 / XP /VISTA
Support SE Biostar se réserve le droit d'ajouter ou de
Biostar se réserve le droit d'ajouter ou de
supprimer le support de SE avec ou sans préavis. supprimer le support de SE avec ou sans préavis.
39
Motherboard Manual
ITALIAN
Ver 5.x
CPU
Ver 6.x
LGA 775
LGA 775
Processore Intel Core2Duo / Core2Quad /
Processore Intel Core2Duo / Core2Quad /
Celeron 4xx / Pentium 4 / Pentium D /
Celeron 4xx / Pentium 4 / Pentium D /
Celeron D
Celeron D
Supporto di Hyper-Threading / Execute
Supporto di Hyper-Threading / Execute
Disable B it / Enhanced Intel SpeedStep® / Disable B it / Enhanced Intel SpeedStep® /
Architettura Intel 64 / Tecno logia Extended Architettura Intel 64 / Tecno logia Extended
FSB
Chipset
Super I/O
Memory 64 / Tecnologia Virtualization
Memory 64 / Tecnologia Virtualization
533 / 800 / 1066 / 1333 MHz
533 / 800 / 1066 / 1333 MHz
Intel P35
Intel P35
Intel ICH9
Intel ICH9
ITE 8718F
ITE 8718F
Fornisce le funzionalità legacy Super I/O
Fornisce le funzionalità legacy Super I/O
usate più comunemente.
usate più comunemente.
Interfaccia LPC (Low Pin Count)
Interfaccia LPC (Low Pin Count)
Funzioni di controllo dell’ambiente:
Funzioni di controllo dell’ambiente:
Monitoraggio hardware
Monitoraggio hardware
Controller / Monitoraggio velocità ventolina Controller / Monitoraggio velocità ventolina
Funzione "Smart Guardian" di ITE
Funzione "Smart Guardian" di ITE
Alloggi DIMM DDR2 x 4
Alloggi DIMM DDR2 x 4
Ciascun DIMM supporta DDR2 256MB /
Ciascun DIMM supporta DDR2 256MB /
512MB / 1GB / 2GB
512MB / 1GB / 2GB
Capacità massima della memoria 8GB
Capacità massima della memoria 8GB
Memoria
Modulo di memoria DDR2 a canale doppio
Modulo di memoria DDR2 a canale doppio
principale
Supporto di DDR2 800 / 667
Supporto di DDR2 800 / 667
Supporto di DDR2 533 (w. FSB 533/1066
Supporto di DDR2 533 (w. FSB 533/1066
CPU)
CPU)
DIMM registrati e DIMM ECC non sono
DIMM registrati e DIMM ECC non sono
supportati
supportati
JMicro JMB368
JMicro JMB368
Modalità Bus Master Ultra DMA 33 / 66 /
Modalità Bus Master Ultra DMA 33 / 66 /
100 / 133
100 / 133
Supporto modalità PIO Mode 0-4
Supporto modalità PIO Mode 0-4
Controller Serial ATA integrato
Controller Serial ATA integrato
Velocità di trasferimento dei dati fino a
Velocità di trasferimento dei dati fino a
3.0Gb/s.
3.0Gb/s.
IDE
SATA
Compatibile specifiche SATA Versione 2.0. Compatibile specifiche SATA Versione 2.0.
40
TP35D2-A7
Ver 5.x
LAN
Supporto
audio HD
Alloggi
Connettori
su scheda
Ver 6.x
Realtek RTL 8110SC / RTL 8100C(optional)
Realtek RTL 8110SC / RTL 8100C(optional)
Negoziazione automatica 10 / 100 / 1000
Negoziazione automatica 10 / 100 / 1000
Mb/s (la larghezza di banda Gigabit è solo Mb/s (la larghezza di banda Gigabit è solo
per RTL 8110SC)
per RTL 8110SC)
Capacità Half / Full Duplex
Capacità Half / Full Duplex
ALC888
ALC861VD
Supporto audio High-Definition (HD)
Supporto audio High-Definition (HD)
Uscita audio 7.1 canali
Uscita audio 5.1 canali
Alloggio PCI
x3
Alloggio PCI
Alloggio PCI Express x16
x1
Alloggio PCI Express x16
x1
Alloggio PCI Express x4
x1
Alloggio PCI Express x4
x1
Alloggio PCI Express x1
x1
Alloggio PCI Express x1
x1
Connettore floppy
x1
Connettore floppy
x1
Connettore Porta stampante
x1
Connettore Porta stampante
x1
Connettore IDE
x1
Connettore IDE
x1
Connettore SATA
x4
Connettore SATA
x4
Connettore pannello frontale
x1
Connettore pannello frontale
x1
Connettore audio frontale
x1
Connettore audio frontale
x1
Connettore CD-in
x1
Connettore CD-in
x1
Connettore output SPDIF
x1
Connettore output SPDIF
x1
Connettore input SPDIF(optional) x1
Connettore input SPDIF(optional) x1
Collettore ventolina CPU
x1
Collettore ventolina CPU
Collettore ventolina sistema
x2
Collettore ventolina sistema
x2
Collettore cancellaz ione CMOS
x1
Collettore cancellaz ione CMOS
x1
x3
Connettore USB
x3
Connettore alimentazione
x1
Connettore alimentazione
x1
x1
Connettore alimentazione
(24 pin)
(24 pin)
(4 pin)
pannello
posteriore
Dimension
i scheda
Sistemi
operativi
supportati
x1
Connettore USB
Connettore alimentazione
I/O
x3
x1
(4 pin)
Tastiera PS/2
x1
Tastiera PS/2
Mouse PS/2
x1
Mouse PS/2
x1
Porta seriale
x1
Porta seriale
x1
Porta LAN
x1
Porta LAN
x1
Porta USB
x6
Porta USB
x6
Connettore audio
x6
Connettore audio
x3
220 mm (larghezza) x 305 mm (altezza)
x1
220 mm (larghezza) x 305 mm (altezza)
Windows 2000 / XP / VISTA
Windows 2000 / XP / VISTA
Biostar si riserva il diritto di aggiungere o
Biostar si riserva il diritto di aggiungere o
rimuovere il supporto di qualsiasi sistema
rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.
operativo senza preavviso.
41
Motherboard Manual
SPANISH
Ver 5.x
Ver 6.x
LGA 775
LGA 775
Procesador Intel Core2Duo / Core2Quad /
Procesador Intel Core2Duo / Core2Quad /
Celeron 4xx / Pentium 4 / Pentium D / Celeron D Celeron 4xx / Pentium 4 / Pentium D / Celeron D
CPU
FSB
Admite Hyper-Threading / Bit de deshabilitación Admite Hyper-Threading / Bit de deshabilitación
de ejecución / Intel SpeedStep® Mejorado /
de ejecución / Intel SpeedStep® Mejorado /
Intel Architecture-64 / Tecnología Extended
Intel Architecture-64 / Tecnología Extended
Memory 64 / Tecnología de virtualización
Memory 64 / Tecnología de virtualización
533 / 800 / 1066 / 1333 MHz
533 / 800 / 1066 / 1333 MHz
Conjunto de Intel P35
Intel P35
chips
Intel ICH9
Intel ICH9
ITE 8718F
ITE 8718F
Le ofrece las funcionalidades heredadas de uso
Le ofrece las funcionalidades heredadas de uso
más común Súper E/S.
más común Súper E/S.
Interfaz de cuenta Low Pin
Interfaz de cuenta Low Pin
Iniciativas de control de entorno,
Iniciativas de control de entorno,
Monitor hardware
Monitor hardware
Súper E/S
Controlador/monitor de velocidad de ventilador Controlador/monitor de velocidad de ventilador
Memoria
principal
IDE
SATA
Red Local
42
Función "Guardia inteligente" de ITE
Función "Guardia inteligente" de ITE
Ranuras DIMM DDR2 x 4
Ranuras DIMM DDR2 x 4
Cada DIMM admite DDR de 256MB / 512MB /
Cada DIMM admite DDR de 256MB / 512MB /
1GB / 2GB
1GB / 2GB
Capacidad máxima de memoria de 8GB
Capacidad máxima de memoria de 8GB
Módulo de memoria DDR2 de canal Doble
Módulo de memoria DDR2 de canal Doble
Admite DDR2 de 800 / 667
Admite DDR2 de 800 / 667
Admite DDR2 de 533 (w. FSB 533/1066 CPU)
Admite DDR2 de 533 (w. FSB 533/1066 CPU)
No admite DIMM registrados o DIMM
No admite DIMM registrados o DIMM
compatibles con ECC
compatibles con ECC
JMicro JMB368
JMicro JMB368
Modo bus maestro Ultra DMA 33 / 66 / 100 / 133 Modo bus maestro Ultra DMA 33 / 66 / 100 / 133
Soporte los Modos PIO 0~4,
Soporte los Modos PIO 0~4,
Controlador ATA Serie Integrado
Controlador ATA Serie Integrado
Tasas de transferencia de hasta 3.0 Gb/s.
Tasas de transferencia de hasta 3.0 Gb/s.
Compatible con la versión SATA 2.0.
Compatible con la versión SATA 2.0.
Realtek RTL 8110SC / RTL 8100C (opcional)
Realtek RTL 8110SC / RTL 8100C (opcional)
Negociación de 10 / 100 / 1000 Mb/s (el ancho Negociación de 10 / 100 / 1000 Mb/s (el ancho
de banda Gigabit es únicamente para 8110SC)
de banda Gigabit es únicamente para 8110SC)
Funciones Half / Full dúplex
Funciones Half / Full dúplex
TP35D2-A7
Ver 5.x
Soporte de
sonido HD
ALC888
ALC861VD
Soporte de sonido de Alta Definición
Soporte de sonido de Alta Definición
Salida de sonido de 7.1 canales
Ranura PCI
Ranuras
Conectores
en placa
Ver 6.x
Salida de sonido de 5.1 canales
X3
X1
Ranura PCI Express x16
X1
Ranura PCI Express x4
X1
Ranura PCI Express x4
X1
Ranura PCI express x 1
X1
Ranura PCI express x 1
X1
Conector disco flexible
X1
Conector disco flexible
X1
Conector Puerto de impresora
X1
Conector Puerto de impresora
X1
Conector IDE
X1
Conector IDE
X1
Conector SATA
X4
Conector SATA
X4
Conector de panel frontal
X1
Conector de panel frontal
X1
Conector de sonido frontal
X1
Conector de sonido frontal
X1
Conector de entrada de CD
X1
Conector de entrada de CD
X1
Conector de salida S/PDIF
X1
Conector de salida S/PDIF
X1
Conector de entrada S/PDIF(opcional) x1
Conector de entrada S/PDIF(opcional) x1
Cabecera de ventilador de CPU
Cabecera de ventilador de CPU
X1
Cabecera de borrado de CMOS
X1
Conector USB
X3
Conector USB
X3
Conector de alimentación
X1
Conector de alimentación
X1
(24 patillas)
X1
(4 patillas)
Teclado PS/2
Tamaño de
la placa
Cabecera de ventilador de sistema X2
X1
Conector de alimentación
E/S
X1
Cabecera de borrado de CMOS
(24 patillas)
trasero de
X3
Ranura PCI Express x16
Cabecera de ventilador de sistema X2
Panel
Ranura PCI
Conector de alimentación
X1
(4 patillas)
X1
Teclado PS/2
Ratón PS/2
X1
Ratón PS/2
X1
Puerto serie
X1
Puerto serie
X1
Puerto de red local
X1
Puerto de red local
X1
Puerto USB
X6
Puerto USB
X6
Conector de sonido
X6
Conector de sonido
X3
220 mm. (A) X 305 Mm. (H)
Soporte de Windows 2000 / XP / VISTA
X1
220 mm. (A) X 305 Mm. (H)
Windows 2000 / XP / VISTA
sistema
Biostar se reserva el derecho de añadir o retirar Biostar se reserva el derecho de añadir o retirar
operativo
el soporte de cualquier SO con o sin aviso previo. el soporte de cualquier SO con o sin aviso previo.
43
Motherboard Manual
PORTUGUESE
Ver 5.x
Ver 6.x
LGA 775
LGA 775
Processador Intel Core2Duo / Core2Quad /
Processador Intel Core2Duo / Core2Quad /
Celeron 4xx / Pentium 4 / Pentium D / Celeron D Celeron 4xx / Pentium 4 / Pentium D / Celeron D
CPU
Suporta as tecnologias Hyper-Threading /
Suporta as tecnologias Hyper-Threading /
Execute Disable Bit / Enhanced Intel
Execute Disable Bit / Enhanced Intel
SpeedStep® / Intel Arquitecture -64 / Extended SpeedStep® / Intel Arquitecture -64 / Extended
Memory 64 / Virtualization
FSB
Chipset
Memory 64 / Virtualization
533 / 800 / 1066 / 1333 MHz
533 / 800 / 1066 / 1333 MHz
Intel P35
Intel P35
Intel ICH9
Intel ICH9
ITE 8718F
ITE 8718F
Proporciona as funcionalidades mais utilizadas
Proporciona as funcionalidades mais utilizadas
em termos da especificação Super I/O.
em termos da especificação Super I/O.
Especificaçã Interface LPC (Low Pin Count).
Interface LPC (Low Pin Count).
o Super I/O Iniciativas para controlo do ambiente
Iniciativas para controlo do ambiente
Monitorização do hardware
Monitorização do hardware
Controlador/Monitor da velocidade da ventoinha Controlador/Monitor da velocidade da ventoinha
Função "Smart Guardian" da ITE
Função "Smart Guardian" da ITE
Ranhuras DIMM DDR2 x 4
Ranhuras DIMM DDR2 x 4
Cada módulo DIMM suporta uma memória
Cada módulo DIMM suporta uma memória
DDR2 de 256 MB / 512 MB / 1GB / 2GB
DDR2 de 256 MB / 512 MB / 1GB / 2GB
Capacidade máxima de memória:8 GB
Capacidade máxima de memória:8 GB
Memória
Módulo de memória DDR2 de canal duplo
Módulo de memória DDR2 de canal duplo
principal
Suporta módulos DDR2 800 / 667
Suporta módulos DDR2 800 / 667
Suporta módulos DDR2 533 (w. FSB 533/1066 Suporta módulos DDR2 533 (w. FSB 533/1066
IDE
SATA
LAN
44
CPU)
CPU)
Os módulos DIMM registados e os DIMM ECC
Os módulos DIMM registados e os DIMM ECC
não são suportados
não são suportados
JMicro JMB368
JMicro JMB368
Modo Bus master Ultra DMA 33 / 66 / 100 / 133 Modo Bus master Ultra DMA 33 / 66 / 100 / 133
Suporta o modo PIO 0~4,
Suporta o modo PIO 0~4,
Controlador Serial ATA integrado
Controlador Serial ATA integrado
Velocidades de transmissão de dados até 3.0
Velocidades de transmissão de dados até 3.0
Gb/s.
Gb/s.
Compatibilidade com a especificação SATA
Compatibilidade com a especificação SATA
versão 2.0.
versão 2.0.
Realtek RTL 8110SC / RTL 8100C(opcional)
Realtek RTL 8110SC / RTL 8100C(opcional)
Auto negociação de 10 / 100 / 1000 Mb/s (a
Auto negociação de 10 / 100 / 1000 Mb/s (a
largura de banda Gigabit refere-se apenas à
largura de banda Gigabit refere-se apenas à
especificação RTL 8110SC)
especificação RTL 8110SC)
Capacidade semi/full-duplex
Capacidade semi/full-duplex
TP35D2-A7
Ver 5.x
Suporte
para áudio
de alta
definição
Ranhuras
Conectores
na placa
Ver 6.x
ALC888
ALC861VD
Suporta a especificação High-Definition Audio
Suporta a especificação High-Definition Audio
Saída de áudio de 7.1 canais
Saída de áudio de 5.1 canais
Ranhura PCI
x3
Ranhura PCI
x3
Ranhura PCI Express x16
x1
Ranhura PCI Express x16
x1
Ranhura PCI Express x4
x1
Ranhura PCI Express x4
x1
Ranhura PCI Express x 1
x1
Ranhura PCI Express x 1
x1
Conector da unidade de disquetes
x1
Conector da unidade de disquetes
x1
Conector da para impressora
x1
Conector da para impressora
x1
Conector IDE
x1
Conector IDE
x1
Conector SATA
x4
Conector SATA
x4
Conector do painel frontal
x1
Conector do painel frontal
x1
Conector de áudio frontal
x1
Conector de áudio frontal
x1
Conector para entrada de CDs
x1
Conector para entrada de CDs
x1
Conector de saída S/PDIF
x1
Conector de saída S/PDIF
x1
Conector de entrada S/PDIF(opcional) x1
Conector de entrada S/PDIF(opcional) x1
Conector da ventoinha da CPU
x1
Conector da ventoinha da CPU
x1
Conector da ventoinha do sistema
x2
Conector da ventoinha do sistema
x2
Conector para limpeza do CMOS
x1
Conector para limpeza do CMOS
x1
Conector USB
x3
Conector USB
x3
Conector de alimentação
x1
Conector de alimentação
x1
(24 pinos)
Conector de alimentação
(24 pinos)
x1
(4 pinos)
Conector de alimentação
x1
(4 pinos)
x1
Teclado PS/2
x1
Entradas/S Rato PS/2
x1
Rato PS/2
x1
aídas no
Porta série
x1
Porta série
x1
painel
Porta LAN
x1
Porta LAN
x1
traseiro
Porta USB
x6
Porta USB
x6
Tomada de áudio
x6
Tomada de áudio
x3
Teclado PS/2
Tamanho
da placa
Sistemas
operativos
suportados
220 mm (L) X 305 mm (A)
220 mm (L) X 305 mm (A)
Windows 2000 / XP / VISTA
Windows 2000 / XP / VISTA
A Biostar reserva-se o direito de adicionar ou
A Biostar reserva-se o direito de adicionar ou
remover suporte para qualquer sistema
remover suporte para qualquer sistema
operativo com ou sem aviso prévio.
operativo com ou sem aviso prévio.
45
Motherboard Manual
POLISH
Ver 5.x
Ver 6.x
LGA 775
LGA 775
Procesor Intel Core2Duo / Core2Quad /
Procesor Intel Core2Duo / Core2Quad /
Celeron 4xx / Pentium 4 / Pentium D / Celeron D Celeron 4xx / Pentium 4 / Pentium D / Celeron D
Procesor
FSB
Chipset
Obsługa Hyper-Threading / Execute Disable Bit / Obsługa Hyper-Threading / Execute Disable Bit /
Enhanced Intel SpeedStep® / Intel
Enhanced Intel SpeedStep® / Intel
Architecture-64 / Extended Memory 64
Architecture-64 / Extended Memory 64
Technology / Virtualization Technology
Technology / Virtualization Technology
533 / 800 / 1066 / 1333 MHz
533 / 800 / 1066 / 1333 MHz
Intel P35
Intel P35
Intel ICH9
Intel ICH9
Gniazda DDR2 DIMM x 4
Gniazda DDR2 DIMM x 4
Każde gniazdo DIMM obsługuje moduły 256MB / Każde gniazdo DIMM obsługuje moduły 256MB /
Pamięć
główna
512MB / 1GB / 2GB
512MB / 1GB / 2GB
Maks. wielkość pamięci 8GB
Maks. wielkość pamięci 8GB
Moduł pamięci DDR2 z trybem podwójnego
Moduł pamięci DDR2 z trybem podwójnego
kanału
kanału
Obsługa DDR2 800 / 667
Obsługa DDR2 800 / 667
Obsługa DDR2 533 (w. FSB 533/1066 CPU)
Obsługa DDR2 533 (w. FSB 533/1066 CPU)
Brak obsługi Registered DIMM oraz ECC DIMM
Brak obsługi Registered DIMM oraz ECC DIMM
ITE 8718F
ITE 8718F
Zapewnia najbardziej powszechne funkcje Super Zapewnia najbardziej powszechne funkcje Super
Super I/O
IDE
SATA
I/O.
I/O.
Interfejs Low Pin Count
Interfejs Low Pin Count
Funkcje kontroli warunków pracy,
Funkcje kontroli warunków pracy,
Monitor H/W
Monitor H/W
Kontroler/Monitor prędkości wentylatora
Kontroler/Monitor prędkości wentylatora
Funkcja ITE "Smart Guardian"
Funkcja ITE "Smart Guardian"
JMicro JMB368
JMicro JMB368
Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master
obsługa PIO tryb 0~4,
obsługa PIO tryb 0~4,
Zintegrowany kontroler Serial ATA
Zintegrowany kontroler Serial ATA
Transfer danych do 3.0 Gb/s.
Transfer danych do 3.0 Gb/s.
Zgodność ze specyfikacją SATA w wersji 2.0.
Zgodność ze specyfikacją SATA w wersji 2.0.
Realtek RTL 8110SC / RTL 8100C (opcja)
Realtek RTL 8110SC / RTL 8100C (opcja)
10 / 100 / 1000 Mb/s z automatyczną negocjacją 10 / 100 / 1000 Mb/s z automatyczną negocjacją
LAN
46
szybkości (Pasmo gigabitowe wyłącznie dla RTL szybkości (Pasmo gigabitowe wyłącznie dla RTL
8110SC)
8110SC)
Działanie w trybie połowicznego / pełnego
Działanie w trybie połowicznego / pełnego
dupleksu
dupleksu
TP35D2-A7
Ver 5.x
Obsługa
audio HD
Gniazda
Złącza
wbudowane
Ver 6.x
ALC888
ALC861VD
Obsługa High-Definition Audio
Obsługa High-Definition Audio
5.1 kanałowe wyjście audio
7.1 kanałowe wyjście audio
Gniazdo PCI
x3
Gniazdo PCI
x3
Gniazdo PCI Express x16
x1
Gniazdo PCI Express x16
x1
Gniazdo PCI Express x 4
x1
Gniazdo PCI Express x 4
x1
Gniazdo PCI Express x 1
x1
Gniazdo PCI Express x 1
x1
Złącze napędu dyskietek
x1
Złącze napędu dyskietek
x1
Złącze Port drukarki
x1
Złącze Port drukarki
x1
Złącze IDE
x1
Złącze IDE
x1
Złącze SATA
x4
Złącze SATA
x4
Złącze panela przedniego
x1
Złącze panela przedniego
x1
Przednie złącze audio
x1
Przednie złącze audio
x1
Złącze wejścia CD
x1
Złącze wejścia CD
x1
Złącze wyjścia S/PDIF
x1
Złącze wyjścia S/PDIF
x1
Złącze wejścia S/PDIF (opcja)
x1
Złącze wejścia S/PDIF (opcja)
x1
Złącze główkowe wentylatora
procesora
Złącze główkowe wentylatora
x1
Złącze główkowe wentylatora
systemowego
Wymiary
płyty
x1
x2
systemowego
x2
Złącze główkowe kasowania CMOS x1
Złącze główkowe kasowania CMOS x1
Złącze USB
x3
Złącze USB
Złącze zasilania (24 pinowe)
x1
Złącze zasilania (24 pinowe)
x1
Złącze zasilania (4 pinowe)
x1
Złącze zasilania (4 pinowe)
x1
Klawiatura PS/2
x1
Klawiatura PS/2
x1
Mysz PS/2
x1
Mysz PS/2
x1
x3
x1
Port szeregowy
x1
Port LAN
x1
Port LAN
x1
Port USB
x6
Port USB
x6
Gniazdo audio
x6
Gniazdo audio
x3
Back Panel Port szeregowy
I/O
procesora
Złącze główkowe wentylatora
220 mm (S) X 305 mm (W)
220 mm (S) X 305 mm (W)
Obsluga
Windows 2000 / XP / VISTA
Windows 2000 / XP / VISTA
systemu
Biostar zastrzega sobie prawo dodawania lub
Biostar zastrzega sobie prawo dodawania lub
operacyjne odwoływania obsługi dowolnego systemu
go
operacyjnego bez powiadomienia.
odwoływania obsługi dowolnego systemu
operacyjnego bez powiadomienia.
47
Motherboard Manual
RUSSIAN
Ver 5.x
CPU
Ver 6.x
LGA 775
LGA 775
Процессор Intel Core2Duo / Core2Quad /
Процессор Intel Core2Duo / Core2Quad /
Celeron 4xx / Pentium 4 / Pentium D / Celeron D Celeron 4xx / Pentium 4 / Pentium D / Celeron D
(центральн Поддержка технологий Hyper-Threading /
Поддержка технологий Hyper-Threading /
ый
Execute Disable Bit / Enhanced Intel
Execute Disable Bit / Enhanced Intel
процессор) SpeedStep® / Intel Architecture-64 / Extended SpeedStep® / Intel Architecture-64 / Extended
Memory 64 Technology / технологии
Memory 64 Technology / технологии
виртуализация
виртуализация
FSB
533 / 800 / 1066 / 1333 МГц
533 / 800 / 1066 / 1333 МГц
Набор
Intel P35
Intel P35
микросхем Intel ICH9
Слоты DDR2 DIMM x 4
Intel ICH9
Слоты DDR2 DIMM x 4
Каждый модуль DIMM поддерживает 256 МБ / Каждый модуль DIMM поддерживает 256 МБ /
512МБ / 1ГБ / 2ГБ DDR2
512МБ / 1ГБ / 2ГБ DDR2
Максимальная ёмкость памяти 8ГБ
Максимальная ёмкость памяти 8ГБ
Основная
Модуль памяти с двухканальным режимом
Модуль памяти с двухканальным режимом
память
DDR2
DDR2
Поддержка DDR2 800 / 667
Поддержка DDR2 800 / 667
Поддержка DDR2 533 (w. FSB 533/1066 CPU) Поддержка DDR2 533 (w. FSB 533/1066 CPU)
Не поддерживает зарегистрированные
Не поддерживает зарегистрированные
модули DIMM and ECC DIMM
модули DIMM and ECC DIMM
ITE 8718F
ITE 8718F
Обеспечивает наиболее используемые
Обеспечивает наиболее используемые
действующие функциональные возможности действующие функциональные возможности
Super I/O.
Super I/O
IDE
SATA
Super I/O.
Интерфейс с низким количеством выводов
Интерфейс с низким количеством выводов
Инициативы по охране окружающей среды,
Инициативы по охране окружающей среды,
Аппаратный монитор
Аппаратный монитор
Регулятор скорости вентилятора/ монитор
Регулятор скорости вентилятора/ монитор
Функция ITE "Smart Guardian"
Функция ITE "Smart Guardian"
(Интеллектуальная защита)
(Интеллектуальная защита)
JMicro JMB368
JMicro JMB368
Режим "хозяина" шины Ultra DMA 33 / 66 / 100 Режим "хозяина" шины Ultra DMA 33 / 66 / 100
/ 133
/ 133
Поддержка режима PIO 0~4,
Поддержка режима PIO 0~4,
Встроенное последовательное устройство
Встроенное последовательное устройство
управления ATA
управления ATA
скорость передачи данных до 3.0 гигабит/с. скорость передачи данных до 3.0 гигабит/с.
Соответствие спецификации SATA версия 2.0. Соответствие спецификации SATA версия 2.0.
Realtek RTL 8110SC /
Локальная RTL 8100C (дополнительно)
сеть
RTL 8100C (дополнительно)
Автоматическое согласование 10 / 100 / 1000 Автоматическое согласование 10 / 100 / 1000
Мб/с (гигабитная пропускная способность
48
Realtek RTL 8110SC /
Мб/с (гигабитная пропускная способность
TP35D2-A7
Ver 5.x
Ver 6.x
только для гигабитного физического уровня) только для гигабитного физического уровня)
Звуковая
поддержка
жесткого
диска
Слоты
Частичная / полная дуплексная способность
Частичная / полная дуплексная способность
ALC888
ALC861VD
Звуковая поддержка High-Definition
Звуковая поддержка High-Definition
7.1канальный звуковой выход
5.1канальный звуковой выход
Слот PCI
x3
Слот PCI
x3
Слот PCI Express x16
x1
Слот PCI Express x16
x1
Слот PCI Express x 4
x1
Слот PCI Express x 4
x1
Слот PCI Express x 1
x1
Слот PCI Express x 1
x1
Разъём НГМД
x1
Разъём НГМД
x1
Разъём Порт подключения
Встроенны
й разъём
Разъём Порт подключения
принтера
x1
принтера
x1
Разъём IDE
x1
Разъём IDE
x1
Разъём SATA
x4
Разъём SATA
x4
Разъём на лицевой панели
x1
Разъём на лицевой панели
x1
Входной звуковой разъём
x1
Входной звуковой разъём
x1
Разъём ввода для CD
x1
Разъём ввода для CD
x1
Разъём вывода для S/PDIF
x1
Разъём вывода для S/PDIF
x1
Разъём ввода для S/PDIF(дополнительно) x1
Разъём ввода для S/PDIF(дополнительно) x1
Контактирующее приспособление
Контактирующее приспособление
вентилятора центрального процессора x1
вентилятора центрального процессора x1
Контактирующее приспособление
Контактирующее приспособление
вентилятора системы
x2
Открытое контактирующее
вентилятора системы
x2
Открытое контактирующее
приспособление CMOS
x1
приспособление CMOS
x1
USB-разъём
x3
USB-разъём
x3
Разъем питания (24 вывод)
x1
Разъем питания (24 вывод)
x1
Разъем питания (4 вывод)
x1
Разъем питания (4 вывод)
x1
x1
Клавиатура PS/2
x1
Клавиатура PS/2
Задняя
Мышь PS/2
x1
Мышь PS/2
x1
панель
Последовательный порт
x1
Последовательный порт
x1
средств
Порт LAN
x1
Порт LAN
x1
ввода-выв USB-порт
x6
USB-порт
x6
x6
наушников
ода
Гнездо для подключения
наушников
Размер
панели
Гнездо для подключения
220 мм (Ш) X 305 мм (В)
220 мм (Ш) X 305 мм (В)
Windows 2000 / XP / VISTA
Windows 2000 / XP / VISTA
x3
Поддержка Biostar сохраняет за собой право добавлять
Biostar сохраняет за собой право добавлять
OS
или удалять средства обеспечения для OS с
или удалять средства обеспечения для OS с
или без предварительного уведомления.
или без предварительного уведомления.
49
‫‪Motherboard Manual‬‬
‫‪ARABIC‬‬
‫‪Ver 6.x‬‬
‫‪Ver 5.x‬‬
‫‪LGA 775‬‬
‫‪LGA 775‬‬
‫‪Intel Core2Duo / Core2Quad / Celeron 4xx‬ﻣﻌﺎﻟﺠﺎت ‪Intel Core2Duo / Core2Quad / Celeron 4xx‬ﻣﻌﺎﻟﺠﺎت‬
‫وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ‬
‫اﻟﻤﺮآﺰﻳﺔ‬
‫ﺑﺘﺮدد ﻳﺼﻞ إﻟﻰ ‪/ Pentium 4 / Pentium D / Celeron D‬‬
‫ﺑﺘﺮدد ﻳﺼﻞ إﻟﻰ ‪/ Pentium 4 / Pentium D / Celeron D‬‬
‫‪Hyper-Threading / Execute Disable Bit /‬ﺕﺪﻋﻢ ﺕﻘﻨﻴﺎت‬
‫‪Hyper-Threading / Execute Disable Bit /‬ﺕﺪﻋﻢ ﺕﻘﻨﻴﺎت‬
‫‪Enhanced Intel SpeedStep® / Intel‬‬
‫‪Enhanced Intel SpeedStep® / Intel‬‬
‫‪Architecture-64 / Extended Memory 64‬‬
‫‪Architecture-64 / Extended Memory 64‬‬
‫‪Technology / Virtualization Technology‬‬
‫‪Technology / Virtualization Technology‬‬
‫اﻟﻨﺎﻗﻞ اﻷﻣﺎﻣﻲ اﻟﺠﺎﻥﺒﻲ ﻣﻴﺠﺎ هﺮﺕﺰ ‪ 533 / 800 / 1066 / 1333‬ﺕﺮدد‬
‫ﻣﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ‬
‫ﻣﻴﺠﺎ هﺮﺕﺰ ‪ 533 / 800 / 1066 / 1333‬ﺕﺮدد‬
‫‪Intel P35‬‬
‫‪Intel P35‬‬
‫‪Intel ICH9‬‬
‫‪Intel ICH9‬‬
‫ﻓﺘﺤﺔ ‪DDR2 DIMM‬‬
‫ﻋﺪد‪4‬‬
‫ﻓﺘﺤﺔ ‪DDR2 DIMM‬‬
‫ﻋﺪد‪4‬‬
‫ﻣﻴﺠﺎ ‪ 256/512‬ﺳﻌﺔ ‪ DDR2‬ﺕﺪﻋﻢ ذاآﺮة ﻣﻦ ﻥﻮع ‪DIMM‬ﺕﺪﻋﻢ آﻞ ﻓﺘﺤﺔ ﻣﻴﺠﺎ ‪ 256/512‬ﺳﻌﺔ ‪ DDR2‬ﺕﺪﻋﻢ ذاآﺮة ﻣﻦ ﻥﻮع ‪DIMM‬ﺕﺪﻋﻢ آﻞ ﻓﺘﺤﺔ‬
‫اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ‬
‫‪Super I/O‬‬
‫ﻣﻨﻔﺬ ‪IDE‬‬
‫‪SATA‬‬
‫ﺷﺒﻜﺔ داﺧﻠﻴﺔ‬
‫ﺑﺎﻳﺖ و‪ 2‬ﺑﺎﻳﺖ و‪ 1‬ﺝﻴﺠﺎ ﺑﺎﻳﺖ‬
‫ﺑﺎﻳﺖ و‪ 2‬ﺑﺎﻳﺖ و‪ 1‬ﺝﻴﺠﺎ ﺑﺎﻳﺖ‬
‫ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى ‪ 8‬ﺝﻴﺠﺎ ﺑﺎﻳﺖ‬
‫ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى ‪ 8‬ﺝﻴﺠﺎ ﺑﺎﻳﺖ‬
‫ﻣﺰدوﺝﺔ اﻟﻘﻨﺎة‪DDR2‬وﺣﺪة ذاآﺮة‬
‫ﻣﺰدوﺝﺔ اﻟﻘﻨﺎة‪DDR2‬وﺣﺪة ذاآﺮة‬
‫ﺳﻌﺎت ‪ 800 / 667‬ﻣﻴﺠﺎ ﺑﺎﻳﺖ‪DDR2‬ﺕﺪﻋﻢ اﻟﺬاآﺮة ﻣﻦ ﻥﻮع‬
‫ﺳﻌﺎت ‪ 800 / 667‬ﻣﻴﺠﺎ ﺑﺎﻳﺖ‪DDR2‬ﺕﺪﻋﻢ اﻟﺬاآﺮة ﻣﻦ ﻥﻮع‬
‫‪ (w. FSB‬ﺳﻌﺎت ‪ 533‬ﻣﻴﺠﺎ ﺑﺎﻳﺖ‪DDR2‬ﺕﺪﻋﻢ اﻟﺬاآﺮة ﻣﻦ ﻥﻮع‬
‫‪ (w. FSB‬ﺳﻌﺎت ‪ 533‬ﻣﻴﺠﺎ ﺑﺎﻳﺖ‪DDR2‬ﺕﺪﻋﻢ اﻟﺬاآﺮة ﻣﻦ ﻥﻮع‬
‫)‪533/1066 CPU‬‬
‫)‪533/1066 CPU‬‬
‫‪ ECC‬وﺕﻠﻚ اﻟﺘﻲ ﻻ ﺕﺘﻮاﻓﻖ ﻣﻊ ‪DIMM‬ﻻ ﺕﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة‬
‫‪ ECC‬وﺕﻠﻚ اﻟﺘﻲ ﻻ ﺕﺘﻮاﻓﻖ ﻣﻊ ‪DIMM‬ﻻ ﺕﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة‬
‫‪ITE 8718F‬‬
‫‪ITE 8718F‬‬
‫اﻷآﺜﺮ اﺳﺘﺨﺪاﻣًﺎ‪Super I/O .‬ﺕﻮﻓﺮ وﻇﻴﻔﺔ‬
‫اﻷآﺜﺮ اﺳﺘﺨﺪاﻣًﺎ‪Super I/O .‬ﺕﻮﻓﺮ وﻇﻴﻔﺔ‬
‫‪Low Pin Count Interface‬ﺕﺪﻋﻢ ﺕﻘﻨﻴﺔ‬
‫‪Low Pin Count Interface‬ﺕﺪﻋﻢ ﺕﻘﻨﻴﺔ‬
‫وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ‪:‬‬
‫وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ‪:‬‬
‫ﻣﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺝﻬﺰة‬
‫ﻣﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺝﻬﺰة‬
‫ﻣﺮاﻗﺐ ﻓﻲ ﺳﺮﻋﺔ اﻟﻤﺮوﺣﺔ‬
‫ﻣﺮاﻗﺐ ﻓﻲ ﺳﺮﻋﺔ اﻟﻤﺮوﺣﺔ‬
‫‪ ITE‬ﻣﻦ "‪"Smart Guardian‬وﻇﻴﻔﺔ‬
‫‪ ITE‬ﻣﻦ "‪"Smart Guardian‬وﻇﻴﻔﺔ‬
‫ﻣﺘﻜﺎﻣﻞ‪IDE‬ﻣﺘﺤﻜﻢ ‪JMicro JMB368‬‬
‫ﻣﺘﻜﺎﻣﻞ‪IDE‬ﻣﺘﺤﻜﻢ ‪JMicro JMB368‬‬
‫وﺿﻊ رﺋﻴﺴﻲ‪Ultra DMA 33 / 66 / 100 / 133‬ﻥﺎﻗﻞ ﺑﺘﻘﻨﻴﺔ‬
‫وﺿﻊ رﺋﻴﺴﻲ‪Ultra DMA 33 / 66 / 100 / 133‬ﻥﺎﻗﻞ ﺑﺘﻘﻨﻴﺔ‬
‫‪PIO Mode 0~4‬دﻋﻢ وﺿﻊ‬
‫‪PIO Mode 0~4‬دﻋﻢ وﺿﻊ‬
‫ﻣﺘﻜﺎﻣﻞ‪Serial ATA‬ﻣﺘﺤﻜﻢ‬
‫ﻣﺘﻜﺎﻣﻞ‪Serial ATA‬ﻣﺘﺤﻜﻢ‬
‫ﺝﻴﺠﺎﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‪3.0.‬ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺕﺼﻞ إﻟﻰ‬
‫ﺝﻴﺠﺎﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‪3.0.‬ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺕﺼﻞ إﻟﻰ‬
‫‪ 2.0.‬اﻹﺹﺪار ‪SATA‬ﻣﻄﺎﺑﻘﺔ ﻟﻤﻮاﺹﻔﺎت‬
‫‪ 2.0.‬اﻹﺹﺪار ‪SATA‬ﻣﻄﺎﺑﻘﺔ ﻟﻤﻮاﺹﻔﺎت‬
‫‪Realtek RTL 8110SC /‬‬
‫‪Realtek RTL 8110SC /‬‬
‫)اﺥﺘﻴﺎري(‪RTL 8100C‬‬
‫)اﺥﺘﻴﺎري(‪RTL 8100C‬‬
‫ﺕﻔﺎوض ﺕﻠﻘﺎﺋﻲ ‪ 100/10‬ﻣﻴﺠﺎ ﺑﺎﻳﺖ ‪ /‬ﺙﺎﻥﻴﺔ و‪1‬ﺝﻴﺠﺎ ﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‬
‫ﺕﻔﺎوض ﺕﻠﻘﺎﺋﻲ ‪ 100/10‬ﻣﻴﺠﺎ ﺑﺎﻳﺖ ‪ /‬ﺙﺎﻥﻴﺔ و‪1‬ﺝﻴﺠﺎ ﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‬
‫‪50‬‬
‫‪TP35D2-A7‬‬
‫‪Ver 5.x‬‬
‫دﻋﻢ اﻝﺼﻮت ﻋﺎﻝﻲ‬
‫اﻝﺘﻌﺮیﻒ‬
‫‪Ver 6.x‬‬
‫‪RTL 8110SC‬اﻟﻨﻄﺎق اﻟﺘﺮددي ﻟﻠﺠﻴﺠﺎﺑﺖ ﻣﻘﺼﻮر ﻓﻘﻂ ﻋﻠﻰ‬
‫‪RTL 8110SC‬اﻟﻨﻄﺎق اﻟﺘﺮددي ﻟﻠﺠﻴﺠﺎﺑﺖ ﻣﻘﺼﻮر ﻓﻘﻂ ﻋﻠﻰ‬
‫إﻣﻜﺎﻥﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻣﻞ‪/‬اﻟﻨﺼﻔﻲ‬
‫إﻣﻜﺎﻥﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻣﻞ‪/‬اﻟﻨﺼﻔﻲ‬
‫‪ALC888‬‬
‫‪ALC861VD‬‬
‫ﺕﺪﻋﻢ ﺕﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮﻳﻒ ﻣﻦ‬
‫‪Intel‬ﺕﺪﻋﻢ ﺕﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮﻳﻒ ﻣﻦ‬
‫‪ 7.1‬ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت‬
‫‪ 5.1‬ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت‬
‫ﻓﺘﺤﺔ ‪PCI‬‬
‫ﻋﺪد ‪3‬‬
‫ﻓﺘﺤﺔ ‪PCI‬‬
‫ﻋﺪد ‪3‬‬
‫ﻓﺘﺤﺔ ‪PCI Express x16‬‬
‫ﻋﺪد ‪1‬‬
‫ﻓﺘﺤﺔ ‪PCI Express x16‬‬
‫ﻋﺪد ‪1‬‬
‫ﻓﺘﺤﺔ ‪PCI Express x4‬‬
‫ﻋﺪد ‪1‬‬
‫ﻓﺘﺤﺔ ‪PCI Express x4‬‬
‫ﻋﺪد ‪1‬‬
‫ﻓﺘﺤﺔ ‪PCI Express x 1‬‬
‫ﻋﺪد ‪1‬‬
‫ﻓﺘﺤﺔ ‪PCI Express x 1‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﻣﺤﺮك أﻗﺮاص ﻣﺮﻥﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﻣﺤﺮك أﻗﺮاص ﻣﺮﻥﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﻃﺎﺑﻌﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﻃﺎﺑﻌﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ‪IDE‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ‪IDE‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ‪SATA‬‬
‫ﻋﺪد ‪4‬‬
‫ﻣﻨﻔﺬ ‪SATA‬‬
‫ﻋﺪد ‪4‬‬
‫ﻣﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ اﻟﺼﻮت اﻷﻣﺎﻣﻲ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ اﻟﺼﻮت اﻷﻣﺎﻣﻲ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ‪CD-IN‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ‪CD-IN‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﺥﺮج ‪S/PDIF‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﺥﺮج ‪S/PDIF‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ دﺥﻞ )اﺥﺘﻴ ﺎري(‪S/PDIF‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ دﺥﻞ )اﺥﺘﻴ ﺎري(‪S/PDIF‬‬
‫ﻋﺪد ‪1‬‬
‫وﺹﻠﺔ ﻣﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ‬
‫ﻋﺪد ‪1‬‬
‫وﺹﻠﺔ ﻣﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ‬
‫ﻋﺪد ‪1‬‬
‫وﺹﻠﺔ ﻣﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫ﻋﺪد ‪2‬‬
‫وﺹﻠﺔ ﻣﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫ﻋﺪد ‪2‬‬
‫وﺹﻠﺔ ﻣﺴﺢ ‪CMOS‬‬
‫ﻋﺪد ‪1‬‬
‫وﺹﻠﺔ ﻣﺴﺢ ‪CMOS‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ‪USB‬‬
‫ﻋﺪد ‪3‬‬
‫ﻣﻨﻔﺬ ‪USB‬‬
‫ﻋﺪد ‪3‬‬
‫ﻣﻨﻔﺬ ﺕﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪24‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﺕﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪24‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﺕﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪4‬دﺑﺎﺑﻴﺲ(‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﺕﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪4‬دﺑﺎﺑﻴﺲ(‬
‫ﻋﺪد ‪1‬‬
‫ﻟﻮﺣﺔ ﻣﻔﺎﺕﻴﺢ ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻟﻮﺣﺔ ﻣﻔﺎﺕﻴﺢ ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﺎوس ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﺎوس ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﺎﻓﺬ دﺧﻞ‪/‬ﺧﺮج‬
‫ﻣﻨﻔﺬ ﺕﺴﻠﺴﻠﻲ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﺕﺴﻠﺴﻠﻲ‬
‫ﻋﺪد ‪1‬‬
‫اﻝﻠﻮﺣﺔ اﻝﺨﻠﻔﻴﺔ‬
‫ﻣﻨﻔﺬ ﺵﺒﻜﺔ اﺕﺼﺎل ﻣﺤﻠﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﺵﺒﻜﺔ اﺕﺼﺎل ﻣﺤﻠﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﺎﻓﺬ ‪USB‬‬
‫ﻋﺪد ‪6‬‬
‫ﻣﻨﺎﻓﺬ ‪USB‬‬
‫ﻋﺪد ‪6‬‬
‫ﻣﻘﺒﺲ ﺹﻮت‬
‫ﻋﺪد ‪6‬‬
‫ﻣﻘﺒﺲ ﺹﻮت‬
‫ﻋﺪد ‪3‬‬
‫اﻟﻔﺘﺤﺎت‬
‫اﻝﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ‬
‫اﻝﻠﻮﺣﺔ‬
‫ﺣﺠﻢ اﻝﻠﻮﺣﺔ‬
‫دﻋﻢ أﻥﻈﻤﺔ اﻝﺘﺸﻐﻴﻞ‬
‫‪51‬‬
‫‪ 220‬ﻣﻢ )ﻋﺮض( ‪ 305 X‬ﻣﻢ )ارﺕﻔﺎع(‬
‫‪ 220‬ﻣﻢ )ﻋﺮض( ‪ 305 X‬ﻣﻢ )ارﺕﻔﺎع(‬
‫‪Windows 2000 / XP / VISTA‬‬
‫‪Windows 2000 / XP / VISTA‬‬
‫ﺏﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻝﺔ اﻝﺪﻋﻢ ﻷي ﻥﻈﺎم ﺕﺸﻐﻴﻞ ﺏﺈﺧﻄﺎر ‪Biostar‬ﺕﺤﺘﻔﻆ‬
‫ﺏﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻝﺔ اﻝﺪﻋﻢ ﻷي ﻥﻈﺎم ﺕﺸﻐﻴﻞ ﺏﺈﺧﻄﺎر ‪Biostar‬ﺕﺤﺘﻔﻆ‬
‫أو ﺏﺪون إﺧﻄﺎر‪.‬‬
‫أو ﺏﺪون إﺧﻄﺎر‪.‬‬
Motherboard Manual
JAPANESE
Ver 5.x
CPU
Ver 6.x
LGA 775
LGA 775
Intel Core2Duo / Core2Quad / Celeron 4xx /
Intel Core2Duo / Core2Quad / Celeron 4xx /
Pentium 4 / Pentium D / Celeron D processor
Pentium 4 / Pentium D / Celeron D processor
Hyper-Threading / Execute Disable Bit /
Hyper-Threading / Execute Disable Bit /
Enhanced Intel SpeedStep® / Intel
Enhanced Intel SpeedStep® / Intel
Architecture-64 / Extended Memory 64
Architecture-64 / Extended Memory 64
Technology / Virtualization Technologyをサポート Technology / Virtualization Technologyをサポート
します
FSB
チップセット
します
533 / 800 / 1066 / 1333 MHz
533 / 800 / 1066 / 1333 MHz
Intel P35
Intel P35
Intel ICH9
Intel ICH9
DDR2 DIMMスロット x 4
DDR2 DIMMスロット x 4
各DIMMは 256MB / 512MB / 1GB / 2GB DDR2を 各DIMMは 256MB / 512MB / 1GB / 2GB DDR2を
メインメモリ
サポート
サポート
最大メモリ容量8GB
最大メモリ容量8GB
デュアル チャンネルモードDDR2メモリモジュール
デュアル チャンネルモードDDR2メモリモジュール
DDR2 800 / 667をサポート
DDR2 800 / 667をサポート
DDR2 533をサポート (w. FSB 533/1066 CPU)
DDR2 533をサポート (w. FSB 533/1066 CPU)
登録済みDIMMとECC DIMMはサポートされません
登録済みDIMMとECC DIMMはサポートされません
ITE 8718F
ITE 8718F
もっとも一般に使用されるレガシーSuper I/O機能を もっとも一般に使用されるレガシーSuper I/O機能を
Super I/O
IDE
SATA
LAN
52
採用しています。
採用しています。
低ピンカウントインターフェイス
低ピンカウントインターフェイス
環境コントロールイニシアチブ、
環境コントロールイニシアチブ、
H/Wモニター
H/Wモニター
ファン速度コントローラ/ モニター
ファン速度コントローラ/ モニター
ITEの「スマートガーディアン」機能
ITEの「スマートガーディアン」機能
JMicro JMB368
JMicro JMB368
Ultra DMA 33 / 66 / 100 / 133バスマスタモード
Ultra DMA 33 / 66 / 100 / 133バスマスタモード
PIO Mode 0~4のサポート、
PIO Mode 0~4のサポート、
統合シリアルATAコントローラ
統合シリアルATAコントローラ
最高3.0 Gb/秒のデータ転送速度
最高3.0 Gb/秒のデータ転送速度
SATAバージョン2.0仕様に準拠。
SATAバージョン2.0仕様に準拠。
Realtek RTL 8110SC / RTL 8100C(オプション)
Realtek RTL 8110SC / RTL 8100C(オプション)
10 / 100 / 1000 Mb/秒のオートネゴシエーション
10 / 100 / 1000 Mb/秒のオートネゴシエーション
(Gigabitバンド幅はRTL 8110SC専用です)
(Gigabitバンド幅はRTL 8110SC専用です)
TP35D2-A7
Ver 5.x
HDオーディ
オのサポート
スロット
オンボードコ
ネクタ
Ver 6.x
半/全二重機能
半/全二重機能
ALC888
ALC861VD
ハイデフィニションオーディオのサポート
ハイデフィニションオーディオのサポート
7.1 チャンネルオーディオアウト
5.1 チャンネルオーディオアウト
PCIスロット
x3
PCIスロット
x3
PCI Express x16スロット
x1
PCI Express x16スロット
x1
PCI Express x 4スロット
x1
PCI Express x 4スロット
x1
PCI Express x 1スロット
x1
PCI Express x 1スロット
x1
フロッピーコネクタ
x1
フロッピーコネクタ
x1
プリンタポートコネクタ
x1
プリンタポートコネクタ
x1
IDEコネクタ
x1
IDEコネクタ
x1
SATAコネクタ
x4
SATAコネクタ
x4
フロントパネルコネクタ
x1
フロントパネルコネクタ
x1
フロントオーディオコネクタ
x1
フロントオーディオコネクタ
x1
CDインコネクタ
x1
CDインコネクタ
x1
S/PDIFアウトコネクタ
x1
S/PDIFアウトコネクタ
x1
S/PDIFインコネクタ(オプション)
x1
S/PDIFインコネクタ(オプション)
x1
CPUファンヘッダ
x1
CPUファンヘッダ
x1
システムファンヘッダ
x2
システムファンヘッダ
x2
CMOSクリアヘッダ
x1
CMOSクリアヘッダ
x1
USBコネクタ
x3
USBコネクタ
x3
電源コネクタ(24ピン)
x1
電源コネクタ(24ピン)
x1
電源コネクタ(4ピン)
x1
電源コネクタ(4ピン)
x1
PS/2キーボード
x1
PS/2キーボード
x1
PS/2マウス
x1
PS/2マウス
x1
背面パネル
シリアルポート
x1
シリアルポート
x1
I/O
LANポート
x1
LANポート
x1
USBポート
x6
USBポート
x6
オーディオジャック
x6
オーディオジャック
x3
ボードサイズ 220 mm (幅) X 305 mm (高さ)
Windows 2000 / XP / VISTA
220 mm (幅) X 305 mm (高さ)
Windows 2000 / XP / VISTA
OSサポート Biostarは事前のサポートなしにOSサポートを追加ま Biostarは事前のサポートなしにOSサポートを追加ま
たは削除する権利を留保します。
たは削除する権利を留保します。
2007/05/14
53
TP35D2-A7 BIOS Setup
BIOS Setup ................................................................................................ 1
1 Main Menu ............................................................................................. 3
2 Standard CMOS Features..................................................................... 7
3 Advanced BIOS Features ...................................................................... 9
4 Advanced Chipset Features................................................................. 16
5 Integrated Peripherals......................................................................... 18
6 Power Management Setup................................................................... 24
7 PnP/PCI Configurations...................................................................... 30
8 PC Health Status .................................................................................. 32
9 OverClock Navigator........................................................................... 34
10 CMOS Reload Program (C.R.P.)...................................................... 39
i
TP35D2-A7
BIOS Setup
Introduction
The purpose of this manual is to describe the settings in the Phoenix-Award™
BIOS Setup program on this motherboard. The Setup program allows users to
modify the basic system configuration and save these settings to CMOS RAM.
The power of CMOS RAM is supplied by a battery so that it retains the Setup
information when the power is turned off.
Basic Input-Output System (BIOS) determines what a computer can do without
accessing programs from a disk. This system controls most of the input and
output devices such as keyboard, mouse, serial ports and disk drives. BIOS
activates at the first stage of the booting process, loading and executing the
operating system. Some additional features, such as virus and password
protection or chipset fine-tuning options are also included in BIOS.
The rest of this manual will to guide you through the options and settings in
BIOS Setup.
Plug and Play Support
This PHOENIX-AWARD BIOS supports the Plug and Play Version 1.0A
specification and ESCD (Extended System Configuration Data) write.
EPA Green PC Support
This PHOENIX-AWARD BIOS supports Version 1.03 of the EPA Green PC
specification.
APM Support
This PHOENIX-AWARD BIOS supports Version 1.1&1.2 of the Advanced
Power Management (APM) specification. Power management features are
implemented via the System Management Interrupt (SMI). Sleep and Suspend
power management modes are supported. Power to the hard disk drives and
video monitors can also be managed by this PHOENIX-AWARD BIOS.
1
TP35D2-A7
ACPI Support
Phoenix-Award ACPI BIOS support Version 1.0b of Advanced Configuration
and Power interface specification (ACPI). It provides ASL code for power
management and device configuration capabilities as defined in the ACPI
specification, developed by Microsoft, Intel and Toshiba.
PCI Bus Support
This PHOENIX-AWARD BIOS also supports Version 3.0 of the Intel PCI
(Peripheral Component Interconnect) local bus specification.
DRAM Support
DDR SDRAM (Double Data Rate Synchronous DRAM) is supported.
Supported CPUs
This PHOENIX-AWARD BIOS supports the Intel CPU.
Using Setup
Use the arrow keys to highlight items in most of the place, press <Enter> to
select, use the <PgUp> and <PgDn> keys to change entries, press <F1> for help
and press <Esc> to quit. The following table provides more detail about how to
navigate in the Setup program by using the keyboard.
Keystroke
Up arrow
Down arrow
Left arrow
Right arrow
Move Enter
PgUp key
PgDn key
+ Key
- Key
Esc key
F1 key
F5 key
F7 key
F10 key
Function
Move to previous item
Move to next item
Move to the item on the left (menu bar)
Move to the item on the right (menu bar)
Move to the item you desired
Increase the numeric value or make changes
Decrease the numeric value or make changes
Increase the numeric value or make changes
Decrease the numeric value or make changes
Main Menu – Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu – E xit
Current page and return to Main Menu
General help on Setup navigation keys
Load previous values from CMOS
Load the optimized defaults
Save all the CMOS changes and exit
2
TP35D2-A7
1 Main Menu
Once you enter Phoenix-Award BIOS™ CMOS Setup Utility, the Main Menu
will appear on the screen. The Main Menu allows you to select from several
setup functions. Use the arrow keys to select among the items and press <Enter>
to accept and enter the sub-menu.
!! WARNING !!
For better system performance, the BIOS firmware is being
continuously updated. The BIOS information described in
this manual (Figure 1, 2, 3, 4, 5, 6, 7, 8, 9,10) is for your
reference only. The actual BIOS information and settings on
board may be slightly different from this manual.
„ Figure 1: Main Menu
Standard CMOS Features
This submenu contains industry standard configurable options.
3
TP35D2-A7
Advanced BIOS Features
This submenu allows you to configure advanced features of the BIOS.
Advanced Chipset Features
This submenu allows you to configure special chipset features.
Integrated Peripherals
This submenu allows you to configure certain IDE hard drive options and
Programmed Input/ Output features.
Power Management Setup
This submenu allows you to configure the power management features.
PnP/PCI Configurations
This submenu allows you to configure certain “Plug and Play” and PCI options.
PC Health Status
This submenu allows you to monitor the hardware of your system.
OverClock Navigator Engine (O.N.E.)
ONE provides two powerful overclock engines, MOS & AOS for both
overclock expertise and beginner.
CMOS Reload Program (C.R.P.)
The CMOS Reload Program (CRP) allows you to save different CMOS settings
into BIOS-ROM.
4
TP35D2-A7
Load Optimized Defaults
This selection allows you to reload the BIOS when problem occurs during
system booting sequence. These configurations are factory settings optimized
for this system. A confirmation message will be displayed before defaults are
set.
Set Supervisor Password
Setting the supervisor password will prohibit everyone except the supervisor
from making changes using the CMOS Setup Utility. You will be prompted with
to enter a password.
Set User Password
If the Supervisor Password is not set, then the User Password will function in
the same way as the Supervisor Password. If the Supervisor Password is set and
the User Password is set, the “User” will only be able to view configurations but
will not be able to change them.
Save & Exit Setup
Save all configuration changes to CMOS (memory) and exit setup. Confirmation
message will be displayed before proceeding.
5
TP35D2-A7
Exit Without Saving
Abandon all changes made during the current session and exit setup.
Confirmation message will be displayed before proceeding.
Integrate Flashing Program
This submenu allows you to upgrade bios.
6
TP35D2-A7
2 Standard CMOS Features
The items in Standard CMOS Setup Menu are divided into several categories.
Each category includes no, one or more than one setup items. Use the arrow
keys to highlight the item and then use the<PgUp> or <PgDn> keys to select the
value you want in each item.
„ Figure 2: Standard CMOS Setup
Main Menu Selections
This table shows the items and the available options on the Main Menu.
Item
Options
Description
Date
mm : dd : yy
Set the system date. Note
that the ‘Day’ automatically
changes when you set the
date.
Time
hh : mm : ss
Set the system internal
clock.
SATA 1 ~ SATA 4
device
Options are in its sub
menu.
7
Press <Enter> to enter the
sub menu of detailed
options
TP35D2-A7
Item
Options
Description
IDE Channel 1
Master / Slave
Options are in its sub
menu.
Press <Enter> to enter the
sub menu of detailed
options.
360K, 5.25 in
1.2M, 5.25 in
Drive A
720K, 3.5 in
1.44M, 3.5 in
Select the type of floppy
disk drive installed in your
system.
2.88M, 3.5 in
None
All Errors
No Errors
Halt On
All, but Keyboard
All, but Diskette
Select the situation in which
you want the BIOS to stop
the POST process and
notify you.
All, but Disk/ Key
Base Memory
N/A
Displays the amount of
conventional memory
detected during boot up.
Extended Memory
N/A
Displays the amount of
extended memory detected
during boot up.
Total Memory
N/A
Displays the total memory
available in the system.
8
TP35D2-A7
3 Advanced BIOS Features
„ Figure 3: Advanced BIOS Setup
9
TP35D2-A7
CPU Feature
Delay Prior to Thermal
Set this item to enable the CPU Thermal function to engage after the specified
time.
The Choices: 4 Min, 8 Min, 16Min (default), 32 Min.
Thermal Management
This option allows you to select the way to control the “Thermal
Management.”
The Choices: Thermal Monitor 1 (default), Thermal Monitor 2.
TM2 Bus Ratio
This option represents the frequency (bus ratio) of the throttled performance
state that will be initiated when the on-die sensor detects temperature increase.
Min= 0
Max= 255
Key in a DEC number.
The Choices: 0 X (default).
TM2 Bus VID
This option represents the voltage of the throttled performance state that will be
initiated when the on-die sensor detects temperature increase.
The Choices: 0.8375V (default), 0.8375-1.6000.
PPM Mode
The Choices: Native Mode (default), SMM Mode.
10
TP35D2-A7
Limit CPUID MaxVal
Set Limit CPUID MaxVal to 3, it should be “Disabled” for Windows XP.
The Choices: Disabled (default), Enabled.
C1E Function
This item allows you to configure the Enhanced Halt State (C1E) function,
which may reduce the power consumption of your system when the system is
idle.
The Choices: Auto (default),Disabled.
Execute Disable Bit
This item allows you to configure the Execute Disabled Bit function, which
protects your system from buffer overflow attacks.
The Choices: Enabled (default), Disabled.
Virtualization Technology
Virtualization Technology can virtually separate your system resource into
several parts, thus enhance the performance when running virtual machines or
multi interface systems.
The Choices: Enabled (default), Disabled.
Core Multi-Processing
The Choices: Enabled (default), Disabled.
Cache Setup
CPU L3 Cache
Depending on the CPU/chipset in use, you may be able to increase memory
access time with this option.
Enabled (default) Enable cache.
Disabled
Disable cache.
11
TP35D2-A7
Boot Seq & Floppy Setup
This item allows you to setup boot sequence & Floppy.
Hard Disk Boot Priority
The BIOS will attempt to arrange the Hard Disk boot sequence automatically.
You can change the Hard Disk booting sequence here.
The Choices: Pri. Master, Pri. Slave, Sec. Master, Sec. Slave, USB HDD0, USB
HDD1, USB HDD2, and Bootable Add-in Cards.
12
TP35D2-A7
First/Second/Third Boot Device
The BIOS will attempt to load the operating system in this order.
The Choices: Floppy, LS120, Hard Disk, CDROM, ZIP100, USB-FDD,
USB-ZIP, USB-CDROM, LAN, Disabled.
Boot Other Device
When enabled, BIOS will try to load the operating system from other device
when it failed to load from the three devices above.
The Choices: Enabled (default), Disabled.
Boot Up Floppy Seek
When enabled, System will test the floppy drives to determine if they have 40
or 80 tracks during boot up. Disabling this option reduces the time it takes to
boot-up.
The Choices: Enabled (default), Disabled.
Virus Warning
This option allows you to choose the VIRUS Warning feature that is used to
protect the IDE Hard Disk boot sector. If this function is enabled and an attempt
is made to write to the boot sector, BIOS will display a warning message on the
screen and sound an alarm beep.
Disabled (default) Virus protection is disabled.
Enabled
Virus protection is activated.
Hyper-Threading Technology
This option allows you to enable or disabled Hyper-Threading Technology.
“Enabled” for Windows XP and Linux2.4.x (OS optimized for Hyper-Threading
Technology). “Disable” for other OS (OS not optimized for Hyper-Threading
Technology).
The Choices: Enabled (default), Disabled.
Quick Power On Self Test
Enabling this option will cause an abridged version of the Power On Self-Test
(POST) to execute after you power up the computer.
Disabled
Normal POST.
Enabled (default) Enable quick POST.
13
TP35D2-A7
Boot Up NumLock Status
Selects the NumLock State after the system switched on.
The Choices:
On (default)
Numpad is number keys.
Off
Numpad is arrow keys.
Gate A20 Option
Select if chipset or keyboard controller should control Gate A20.
Normal
A pin in the keyboard controller controls GateA20.
Fast (default)
Lets chipset control Gate A20.
Typematic Rate Setting
When a key is held down, the keystroke will repeat at a rate determined by the
keyboard controller. When enabled, the typematic rate and typematic delay can
be configured.
The Choices: Disabled (default), Enabled.
Typematic Rate (Chars/Sec)
Sets the rate at which a keystroke is repeated when you hold the key down.
The Choices: 6 (default), 8, 10, 12, 15, 20, 24, 30.
Typematic Delay (Msec)
Sets the delay time after the key is held down before it begins to repeat the
keystroke.
The Choices: 250 (default), 500, 750, 1000.
Security Option
This option will enable only individuals with passwords to bring the system
online and/or to use the CMOS Setup Utility.
System:
A password is required for the system to boot and is also
required to access the Setup Utility.
Setup (default):
A password is required to access the Setup Utility only.
This will only apply if passwords are set from the Setup main menu.
14
TP35D2-A7
APIC MODE
Selecting Enabled enables APIC device mode reporting from the BIOS to the
operating system.
The Choices: Enabled (default), Disabled.
MPS Version Control For OS
The BIOS supports version 1.1 and 1.4 of the Intel multiprocessor specification.
Select version supported by the operation system running on this computer.
The Choices: 1.4 (default), 1.1.
OS Select For DRAM > 64MB
A choice other than Non-OS2 is only used for OS2 systems with memory
exceeding 64MB.
The Choices: Non-OS2 (default), OS2.
Full Screen LOGO Show
This item allows you to enable/disable Full Screen LOGO Show.
The Choices: Enabled (default), Disabled.
Small Logo(EPA) Show
This item allows you to select whether the “Small Logo” shows.
The Choices: Disabled (default), Enabled.
Summary Screen Show
This item allows you to enable/disable the summary screen. Summary screen
means system configuration and PCI device listing.
The Choices: Disabled (default), Enabled.
15
TP35D2-A7
4 Advanced Chipset Features
This submenu allows you to configure the specific features of the chipset
installed on your system. This chipset manage bus speeds and access to system
memory resources, such as DRAM. It also coordinates communications with the
PCI bus. The default settings that came with your system have been optimized
and therefore should not be changed unless you are suspicious that the settings
have been changed incorrectly.
„ Figure 4: Advanced Chipset Setup
System BIOS Cacheable
Selecting the “Enabled” option allows caching of the system BIOS ROM at
F0000h-FFFFFh, which is able to improve the system performance. However,
any programs that attempts to write to this memory block will cause conflicts
and result in system errors.
The Choices: Enabled (default), Disabled.
16
TP35D2-A7
Memory Hole At 15M-16M
You can reserve this area of system memory for ISA adapter ROM. When this
area is reserved it cannot be cached. Check the user information of peripherals
that need to use this area of system memory for the memory requirements.
The Choices: Disabled (default), Enabled.
PEG Force X1
When using on-chip VGA, this item has to be set as X1.
Disabled (default) PCI Express X16
Enabled
PCI Express X1
17
TP35D2-A7
5 Integrated Peripherals
„ Figure 5. Integrated Peripherals
18
TP35D2-A7
OnChip IDE Device
Highlight the “Press Enter” label next to the “OnChip IDE Device” label and
press enter key will take you a submenu with the following options:
IDE HDD Block Mode
Block mode is also called block transfer, multiple commands, or multiple
sectors read / write. If your IDE hard drive supports block mode (most new
drives do), select Enabled for automatic detection of the optimal number of
block mode (most new drives do), select Enabled for automatic detection of the
optimal number of block read / write per sector where the drive can support.
The Choices: Enabled (default), Disabled.
IDE DMA Transfer Access
This item allows you to enable or disable the IDE DMA transfer access.
The Choices: Enabled (default), Disabled.
IDE Primary/Secondary/Master/Slave PIO
The IDE PIO (Programmed Input / Output) fields let you set a PIO mode (0-4)
for each of the IDE devices that the onboard IDE interface supports. Modes 0
to 4 will increase performance progressively. In Auto mode, the system
automatically determines the best mode for each device.
The Choices: Auto (default), Mode0, Mode1, Mode2, Mode3, Mode4.
19
TP35D2-A7
On-chip Secondary PCI IDE
This item allows you to enable or disable the primary / secondary IDE
Channel.
The Choices: Enabled (default), Disabled.
IDE Primary/Secondary/Master/Slave UDMA
Ultra DMA function can be implemented if it is supported by the IDE hard
drives in your system. As well, your operating environment requires a DMA
driver (Windows 95 or OSR2may need a third party IDE bus master driver). If
your hard drive and your system software both support Ultra DMA, select Auto
to enable BIOS support.
The Choices: Auto (default), Disabled.
LEGACY Mode Support
This item allows you to enable or disable legacy mode support.
The Choices: Disabled (default), Enabled.
Super IO Device
Press Enter to configure the Super I/O Device.
Onboard FDC Controller
Select enabled if your system has a floppy disk controller (FDC) installed on
the system board and you wish to use it. If you installed another FDC or the
system uses no floppy drive, select disabled in this field.
The Choices: Enabled (default), Disabled.
20
TP35D2-A7
Onboard Serial Port 1
Select an address and corresponding interrupt for the first and second serial
ports.
The Choices: 3F8/IRQ4 (default), Disabled, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3,
Auto.
Onboard Parallel Port
This item allows you to determine access onboard parallel port controller with
which I/O Address.
The Choices: 378/IRQ7 (default), 278/IRQ5, 3BC/IRQ7, Disabled.
Parallel Port Mode
This item allows you to determine how the parallel port should function. The
default value is SPP.
The Choices:
SPP (default)
Using Parallel port as Standard Printer Port.
EPP
Using Parallel Port as Enhanced Parallel Port.
ECP
Using Parallel port as Extended Capabilities Port.
ECP+EPP
Using Parallel port as ECP & EPP mode.
ECP Mode Use DMA
Select a DMA Channel for the port.
The Choices: 3 (default), 1.
21
TP35D2-A7
USB Device Setting
Highlight the “Press Enter” label next to the “Onboard Device” label and press
the enter key will take you a submenu with the following options:
USB 1.0/2.0 Controller
If your system contains a Universal Serial Bus (USB) controller, This entry is
to enable/disable Enhanced host controller .
The Choices: Enabled (default), Disabled.
USB Operation Mode
Auto decide USB device operation mode.
[High Speed]: If USB device was high speed device,then it operated on high
speed mode. If USB device was full/low speed,then it operated on full/low
speed mode.
[Full/Low Speed]: All of USB device operated on full/low speed mode.
The Choices: High Speed (default), Full/Low Speed.
USB Keyboard/ Mouse/ USB Storage Function
This item allows you to enable or disable the USB Keyboard/ Mouse/ USB
Storage Legacy Support.
Enabled(default) Enable USB Keyboard/ Mouse/ USB Storage Support.
Disabled
Disable USB Keyboard / Mouse/ USB Storage Support.
22
TP35D2-A7
UFDDA/UFDDB
The Choices: USB Floppy (default).
No Device
[Auto]: According to contents of USB MSD decide boot up type.
[FDD Mode]: The USB MSD always boot up as floppy disk.
[HDD Mode]: The USB MSD always boot up as hard disk.
The Choices: Auto mode (default), FDD mode, HDD mode.
PCIE to PATA IDE cntrlr
The Choices: Auto (default), Disabled.
PCI-E Compliancy Mode
This item allows you to select the PCI-E Compliancy Mode.
The Choices: v1.0a (default), v1.0.
Onboard LAN
This item allows you to enable or disable the Onboard LAN.
The Choices: Enabled (default), Disabled.
Onboard LAN Boot ROM
This item allows you to enable or disable the Onboard LAN Boot ROM.
The Choices: Disabled (default), Enabled.
23
TP35D2-A7
6 Power Management Setup
The Power Management Setup Menu allows you to configure your system to
utilize energy conservation and power up/power down features.
„ Figure 6. Power Management Setup
24
TP35D2-A7
ACPI & Wake Up Events
ACPI Function
This item displays the status of the Advanced Configuration and Power
Management (ACPI).
The Choices: Enabled (default), Disabled.
ACPI Suspend Type
The item allows you to select the suspend type under the ACPI operating
system.
The Choices:
S1 (POS) (default) Power on Suspend
S3 (STR) Suspend to RAM
S1 & S3 POS+STR
Run VGABIOS if S3 Resume
Choosing Enabled will make BIOS run VGA BIOS to initialize the VGA card
when system wakes up from S3 state. The system resume time is shortened if
you disable the function, but system will need AGP driver to initialize the card.
So, if the AGP driver of the VGA card does not support the initialization
feature, the display may work abnormally or not function after S3.
The Choices: Auto (default), Yes, No.
25
TP35D2-A7
Wake-Up by PCI card
When you select “Enable”, a PME signal from PCI card returns the system to
Full On state.
The Choices: Disabled (default), Enabled.
PCI Express PME
The Choices: Disabled (default), Enabled.
Power On by Ring
An input signal on the serial Ring Indicator (RI) line (in other words, an
incoming call on the modem) awakens the system from a soft off state.
The Choices: Enabled, Disabled (default).
USB KB Wake-Up From S3
This item allows you to enable or disabled the USB keyboard wake up from S3
function.
The Choices: Disabled (default), Enabled.
Resume by Alarm
This function is for setting date and time for your computer to boot up. When
enabled, you can choose the date and time of system resume.
The Choices: Disabled (default), Enabled.
Date (of Month) Alarm
You can choose which month the system will boot up.
Time (hh:mm:ss) Alarm
You can choose the system boot up time, input hour, minute and second to
specify.
Note: If you have change the setting, you must let the system boot into
operating system, before this function will work.
POWER ON Function
This item allows you to choose the power on method.
The Choices: Button Only (default), Password, Hot Key, Mouse Move/Click,
Any Key, Keyboard 98.
KB Power ON Password
Input password and press Enter to set the Keyboard power on password.
Hot Key Power ON
Choose the Hot Key combination to boot up the system.
The Choices: Ctrl-F1 (default), Ctrl-F2, Ctrl-F3, Ctrl-F4, Ctrl-F5, Ctrl-F6,
Ctrl-F7, Ctrl-F8, Ctrl-F9, Ctrl-F10, Ctrl-F11, and Ctrl-F12.
26
TP35D2-A7
PWRON After PWR-Fail
This setting specifies how your system should behave after a power fail or
interrupts occurs. By choosing off will leave the computer in the power off
state. Choosing On will reboot the computer. Former-Sts will restore the
system to the status before power failure or interrupt occurs.
The Choices: Off (default), On, Former-Sts.
Reload Timer Events
Primary/Secondary IDE 0/1
You can enable or disable Primary or Secondary RAID 0 or RAID 1 function
under this item.
The Choices: Disabled (default), Enabled.
FDD, COM, LPT Port
You can enable or disable FDD, COM, and LPT port under this item.
The Choices: Disabled (default), Enabled.
PCI PIRQ [A-D]#
You can enable or disable PCI PIRQ [A-D]# under this item.
The Choices: Disabled (default), Enabled.
27
TP35D2-A7
Power Management
This category allows you to select the power saving method and is directly
related to the following modes:
1. HDD Power Down.
2. Suspend Mode.
There are three options of Power Management, three of which have fixed mode
settings
Min. Saving (default)
Minimum power management.
Suspend Mode = 1 hr.
HDD Power Down = 15 min
Max. Saving
Maximum power management only available for sl CPU’s.
Suspend Mode = 1 min.
HDD Power Down = 1 min.
User Define
Allow you to set each option individually.
When you choose user define, you can adjust each of the item from 1 min. to 1
hr. except for HDD Power Down which ranges from 1 min. to 15 min.
Video Off Method
This option determines the manner when the monitor goes blank.
V/H SYNC+Blank
This selection will cause the system to turn off the vertical and horizontal
synchronization ports and write blanks to the video buffer.
Blank Screen
This option only writes blanks to the video buffer.
DPMS (default)
Initial display power management signaling.
Video Off In Suspend
This item determines the monitor status when the system is in Suspend mode.
The Choices: Yes (default), No.
28
TP35D2-A7
Suspend Type
Select the Suspend Type.
The Choices: Stop Grant (default), PwrOn Suspend.
Modem Use IRQ
This determines the IRQ, which can be applied in MODEM use.
The Choices: 3 (default), 4, 5, 7, 9, 10, 11, NA.
Suspend Mode
The item allows you to adjust the system idle time before suspend.
The Choices: Disabled, 1 Min, 2 Min, 4 Min, 6 Min, 8 Min, 10 Min, 20 Min, 30
Min, 40 Min, 1 Hour (default).
HDD Power Down
When enabled, the hard-disk drives will power down after a set time of system
inactivity. All other devices remain active.
The Choices: Disabled, 1 Min, 2 Min, 3 Min, 4 Min, 5 Min, 6 Min, 7 Min, 8
Min, 9 Min, 10 Min, 11 Min, 12 Min, 13 Min, 14 Min, 15 Min (default).
Soft-Off by PWR-BTN
This item determines the behavior of system power button. Instant off turn off
the power immediately, and Delay 4 Sec. will require you to press and hold the
power button for 4 seconds to cut off the system power.
The Choices: Delay 4 Sec, Instant-Off (default).
HPET Support
The Choices: Enabled(default), Disabled.
HPET Mode
The Choices: 32-bit mode (default), 64-bit mode.
29
TP35D2-A7
7 PnP/PCI Configurations
This section describes configuring the PCI bus system. PCI, or Personal
Computer Interconnect, is a system which allows I/O devices to operate at
speeds nearing the speed of the CPU itself uses when communicating with its
own special components. This section covers some very technical items and it is
strongly recommended that only experienced users should make any changes to
the default settings.
„ Figure 7: PnP/PCI Configurations
Init Display First
This item allows you to decide to active whether PCI Slot or on-chip VGA first.
The Choices: PCI Slot (default), PCIEx.
Resources Controlled By
By Choosing “Auto(ESCD)” (default), the system BIOS will detect the system
resources and automatically assign the relative IRQ and DMA channel for each
peripheral. By Choosing “Manual”, the user will need to assign IRQ & DMA for
add-on cards. Be sure that there are no IRQ/DMA and I/O port conflicts.
The Choices: Auto (default), Manual.
30
TP35D2-A7
IRQ Resources
This submenu will allow you to assign each system interrupt a type, depending
on the type of device using the interrupt. When you press the “Press Enter” tag,
you will be directed to a submenu that will allow you to configure the system
interrupts. This is only configurable when “Resources Controlled By” is set to
“Manual”.
IRQ-3
assigned to PCI Device
IRQ-4
assigned to PCI Device
IRQ-5
assigned to PCI Device
IRQ-7
assigned to PCI Device
IRQ-9
assigned to PCI Device
IRQ-10
assigned to PCI Device
IRQ-11
assigned to PCI Device
IRQ-12
assigned to PCI Device
IRQ-14
assigned to PCI Device
IRQ-15
assigned to PCI Device
PCI / VGA Palette Snoop
Some old graphic controllers need to “snoop” on the VGA palette and then map
it to their display as a way to provide boot information and VGA compatibility.
This item allows such snooping to take place.
The Choices: Disabled (default), Enabled.
Assign IRQ For USB
This item allows the users to choose which IRQ to assign for the USB.
The Choices: Enabled (default), Disabled.
Maximum Payload Size
Set the maximum payload size for Transaction packets (TLP).
The Choice: 4096 (default.), 128, 256, 512, 1024, 2048.
31
TP35D2-A7
8 PC Health Status
„ Figure 8: PC Health Status
Shutdown Temperature
This item allows you to set up the CPU shutdown Temperature. This item is
only effective under Windows 98 ACPI mode.
The Choices: 70℃ / 158℉ (default) , 60℃ / 140℉,65℃/ 149℉, 75℃/ 158℉,
80℃/ 158℉, 85℃ / 158℉, 90℃ / 158℉, 95℃ / 158℉, Disabled.
Show H/W Monitor in POST
If you computer contains a monitoring system, it will show PC health status
during POST stage. The item offers several different delay times.
The Choices: Enabled (default), Disabled.
CPU Vcore, NB/SB/DDR Voltage, +3.3V, +5.0V, 12.0V, 5V (SB),
Voltage Battery
Detect the system’s voltage status automatically.
32
TP35D2-A7
Temperature 2
This field displays the current temperature of system.
Current SYS Temp
This field displays the current temperature of the system.
Current CPU Temp
This field displays the current temperature of CPU.
Current CPU FAN Speed
This field displays the current speed of CPU fan.
Current SYS FAN Speed
This field displays the current speed of SYSTEM fan.
Current NBChip FAN Speed
This field displays the current speed of north bridge chip fan.
33
TP35D2-A7
9 OverClock Navigator
„ Figure 9: Over Clock Navigator
OverClock Navigator
OverClock .Navigator is designed for beginners in overclock field.
Based on many test and experiments from Biostar Engineer Team, OverClock
Navigator provides 3 default overclock configurations that are able to raise the
system performance.
The Choices: Normal Operation (default), Automate Overclock,
Manual Overclock.
34
TP35D2-A7
Auto OverClock System
The Overclock Navigator provides 3 different engines helping you to overclock
your system. These engines will boost your system performance to different
level.
The Choices:
V6 Tech Engine
This setting will raise about 5%~10% of whole system performance.
V8 Tech Engine
This setting will raise about 15%~25% of whole system performance.
V12 Tech Engine
This setting will raise about 25%~30% of whole system performance.
Cautions:
1.
2.
Not every AMD CPU performs the above overclock setting ideally; the difference may vary
with the installed CPU model.
From BET experiment, the Atholon64 FX CPU is not suitable for this A.O.S. feature.
35
TP35D2-A7
Manual Overclock System (M.O.S.)
MOS is designed for experienced overclock users.
It allows users to customize personal overclock setting.
Note:
Based on our test results; the overclock function achieved the best performance
on AMD 3000+ CPU
CPU Clock Ratio
The Choices: 8X (default).
Min=6 Max=50 Key in a DEC number.
CPU Clock
The Choices: 100MHz (default).
Min=100 Max=333 Key in a DEC number.
PCIE Clock select
The Choices: Fixed 100 (default), Manual.
PCIE Clock
Display the PCIE Clock frequency; Min=100, Max=200, key in a DEC number.
36
TP35D2-A7
System Memory Frequency
The Choices: Auto (default), 533MHz, 677MHz, 800MHz.
Memory Frequency
This item shows the current memory frequency.
CPU Voltage
This item allows you to select CPU Voltage Control.
The Choices: StartUp (default); Scope: +0.012V~+0.787V.
(G)MCH Voltage
The Choices: 1.300V (default); Scope: 1.300~1.650V, Interval: 0.025V.
FSB Termination Voltage
The Choices: 1. 250V (default) ; Scope: 1.250~1.600, Interval: 0.025V.
Memory Voltage
The Choices: 1.90V (default); Scope: 1.90V~2.95V, Interval: 0.05.
37
TP35D2-A7
Integrated Memory Test
Integrated Memory Test allows users to test memory module compatibilities
without additional device or software.
Step 1:
This item is disabled on default; change it to “Enable” to precede memory test.
Step 2:
When the process is done, change the setting back from “Enabled” to
“Disabled” to complete the test.
38
TP35D2-A7
10 CMOS Reload Program (C.R.P.)
The CMOS Reload Program (CRP) allows you to save different CMOS settings
into BIOS-ROM. You may reload any saved CMOS setting to change system
configurations. Moreover, you may save your ideal overclock setting for easier
overclocking. There are 50 sets record addresses in total, and you may name the
saved CMOS data individually.
„ Figure 10: CMOS Reload Program(C.R.P)
39
Download PDF