Bayliner | Ciera 2858 Command Bridge | Specifications | Bayliner Ciera 2858 Command Bridge Specifications

Engine Serial Number:
Hull Identification Number:
Hull Identification Number
The Hull Identification Number (HIN) is located on the starboard side of the transom. Be sure to record the HIN (and
the engine serial numbers) in the space provided above. Please refer to the HIN for any correspondence or orders.
HIN LOCATION
© 2000 Bayliner Technical Publications. All rights reserved.
No part of this publication may be reproduced, stored in any retrieval system, or transmitted in any form by any means,
electronic, mechanical, photocopying, recording or otherwise, without prior written permission of Bayliner.
Printed in the United States of America.
General Notes
The material in this document is for information only and is subject to change without notice. While reasonable efforts have
been made in the preparation of this document to assure its accuracy, Bayliner assumes no liability resulting from errors or
omissions in this document, or from the use of information contained herein.
Due to our commitment to product improvement, Bayliner reserves the right to make changes in the product design,
specifications, and equipment at any time without notice or obligation. Illustrations and/or photos may show optional equipment.
All Bayliner products meet or exceed USCG (Unites States Coast Guard) and/or NMMA (National Marine Manufacturer’s
Association) construction standards. Manufactured with 1,1,1 Trichloroethane, a substance which harms public health and
environment during the manufacturing process by destroying ozone in the upper atmosphere.
Proprietary Rights
This document discloses subject matter in which Bayliner has proprietary rights. The information and design disclosed herein
were originated by and are the property of Bayliner. Neither receipt nor possession thereof confers or transfers any right to
reproduce, copy, alter or disclose the document or any part thereof, any information contained therein, or to construct boats or
any item from it, except by written permission from or written agreement with Bayliner. This document is to be returned upon
request to Bayliner.
CONTENTS
CHAPTER 1: WELCOME ABOARD!
1
1
1
2
2
2
3
4
Dealer Service
Boating Experience
Engine/Accessories Guidelines
Qualified Maintenance
Special Care For Moored Boats
Safety Standards
Hazard Boxes & Symbols
Carbon Monoxide (CO)
4 Sources of CO
5 Carbon Monoxide Alarm System
5 What To Do If Carbon Monoxide Is Detected
CHAPTER 2: FEATURES / SYSTEMS
6
6
6
7
8
9
10
10
11
12
Dimensions and Tank Capacities
Layout View
Hull Exterior Hardware & Drains
Quick Oil Drain System
Deck Hardware and Accessories
Helm Layout (Command Bridge)
Lifting Sling Locations
Windshield Wiper
Electrical System
12 Volt DC System
12
12
12
13
14
15
Fuses and Circuit Breakers
Batteries
Battery Switch
Battery Charger
Shore Power/110 Volt AC System
Navigation & Communication Equipment
15 VHF Radio (Option)
15 Compass (Option)
16 Depth Finder (Option)
16
16
Audio Equipment
Lighting
16 Navigation and Interior Lights
17
Appliances
18
Propulsion
18 Engine
18
Fuel System
18 Fuel Fill and Vent:
18 Fuel Filters:
18 Anti-siphon Valve:
19
20
20
Bilge Blower
Trim Tabs
Bilge Pumps
21 Autofloat Switches
22
Freshwater System
22 Water Heater
23
Sink & Shower Drain Systems
23 Sump Box Cleaning
23 Sump System Winterization
24
Raw Water System
24 Seacocks
24 Raw Water Strainers
25
26
Marine Head with Holding Tank
Air Conditioning System (Option)
CHAPTER 3: ELECTRICAL ROUTINGS
27
28
29
Hull Wire Harness Routings
Deck Wire Harness Routings
AC Battery Cable Routings
CHAPTER 4: WIRING SCHEMATICS
31
32
33
34
AC Electrical System Dual Dockside
Gas Engine Electrical System
Diesel Engine Electrical System
Fire Suppression System Wiring (Option)
LIMITED WARRANTY
35
35
35
What Is Not Covered
Other Limitations
Your Obligation
1
CHAPTER 1:
WELCOME ABOARD!
This owner’s manual supplement provides specific information about your boat that is not covered in the owner’s
manual. Please study the owner’s manual and this supplement carefully, paying particular attention to the LIMITED
WARRANTY at the end of this supplement. Keep the owner’s manual and supplement on your boat in a secure, yet
readily available place.
Dealer Service
Make sure you receive a full explanation of all systems from the selling dealer before taking delivery of your boat.
Your selling dealer is your key to service. If you experience any problems with your new boat, immediately contact
the selling dealer. If for any reason your selling dealer is unable to help, you can call us direct on our customer service hotline: 360-435-8957 or send us a FAX: 360-403-4235. A Bayliner replacement parts catalog is available
online at: http://www.baylinerparts.com. Replacement parts can be purchased from any authorized Bayliner dealer.
Boating Experience
If this is your first boat or if you are changing to a type of boat you are not familiar with, for your own comfort and
safety, please ensure that you obtain handling and operating experience before assuming command of the boat.
Take one of the boating safety classes offered by the U.S. Power Squadrons or the U.S. Coast Guard Auxiliary. For
more course information, including dates and locations of upcoming classes, contact the organizations directly:
• U.S. Power Squadrons: 1-888-FOR-USPS (1-888-367-8777) or on the Internet at: http://www.usps.org
• U.S. Coast Guard Auxiliary: 1-800-368-5647 or on the Internet at: http://www.cgaux.org
Outside the United States, your selling dealer, national sailing federation or local boat club can advise you of local
sea schools or competent instructors.
!
WARNING!
CONTROL HAZARD! A qualified operator must be in control of the boat at all times. DO NOT
operate your boat while under the influence of alcohol or drugs.
Engine/Accessories Guidelines
Your boat’s engine and accessories were selected to provide optimum performance and service. Installing a different
engine or other accessories may cause unwanted handling characteristics. Should you choose to install a different
engine or to add accessories that will affect the boat’s running trim, have an experienced marine technician perform a
safety inspection and handling test before operating your boat again.
Please be advised that certain modifications to your boat can result in cancellation of your warranty
protection. Always check with your dealer before making any modifications to your boat.
The engine and accessories installed on your boat come with their own operation and maintenance manuals. We
strongly urge you to read and understand these manuals before operating the engine and accessories.
NOTICE
When storing your boat please refer to your engine’s operation and maintenance manuals.
Ciera 2858 Command Bridge • Owner’s Manual Supplement
2
CHAPTER 1: WELCOME ABOARD!
Qualified Maintenance
Failure to maintain your boat’s systems as designed could violate the laws in your jurisdiction and could expose you
and other people to the danger of bodily injury or accidental death. Follow the instructions provided in the owner’s
manual this owner's manual supplement, the engine owner’s manual and all accessory instruction sheets/manuals
included in your boat’s owner’s packet.
!
WARNING!
To maintain the integrity and safety of your boat, only qualified personnel should perform
maintenance on, or in any way modify: The steering system, propulsion system, engine control
system, fuel system, environmental control system, electrical system or navigational system.
Special Care For Moored Boats
If moored in saltwater or fresh water, your boat will collect marine growth on its hull bottom. This will detract from
the boat’s beauty, greatly affect its performance and may damage the gelcoat. There are two methods of slowing
marine growth:
• Periodically haul the boat out of the water and scrub the hull bottom with a bristle brush and a solution of soap and
water.
NOTICE
• To help seal the hull bottom and reduce the possibility of gelcoat blistering on moored boats,
we recommend the application of an epoxy barrier coating, such as INTERLUX, Interprotect 2000E/2001E. The barrier coating should be covered with several coats of anti-fouling
paint.
• Many states regulate the chemical content of bottom paints in order to meet environmental
standards. Check with your local dealer about recommended bottom paints, and about the
laws in effect in your area.
Safety Standards
Your boat’s mechanical and electrical systems were designed to meet safety standards in effect at the time it was
built. Some of these standards were mandated by law, all of them were designed to insure your safety, and the safety
of other people, vessels and property.
In addition to this owner’s manual supplement, please read the owner’s manual and all accessory instruction
sheets for important safety standards and hazard information.
!
DANGER!
DANGER
PERSONAL SAFETY HAZARD! Do not allow anyone to ride on parts of the boat
not designated for such use. Sitting on seat backs, lounging on the forward deck,
bow riding, gunwale riding or occupying the transom platform while underway is
especially hazardous and will cause personal injury or death.
!
DANGER!
DANGER
PERSONAL SAFETY HAZARD! Always secure the anchor and other loose objects before
getting underway. The anchor and other items that are not properly secured can come loose
when the boat is moving and cause personal injury or death.
Ciera 2858 Command Bridge
• Owner’s Manual Supplement
CHAPTER 1: WELCOME ABOARD!
3
Hazard Boxes & Symbols
The hazard boxes and symbols shown below are used throughout this supplement to call attention to potentially
dangerous situations which could lead to either personal injury or product damage. Read these warnings carefully and follow all safety recommendations.
!
DANGER!
This box alerts you to immediate hazards which WILL cause severe personal injury or death if
the warning is ignored.
!
WARNING!
This box alerts you to hazards or unsafe practices which COULD result in severe personal
injury or death if the warning is ignored.
!
CAUTI ON!
This box alerts you to hazards or unsafe practices which COULD result in minor personal
injury or cause product or property damage if the warning is ignored.
NOTICE
This box calls attention to installation, operation or maintenance information, which is important to proper operation but is not hazard related.
EXPLOSION
HAZARD!
OPEN FLAME
HAZARD!
HOT
HAZARD!
ELECTRICAL
HAZARD!
CO POISONING
HAZARD!
PERSONAL INJURY
& FALLING HAZARD!
ROTATING
PROPELLER HAZARD!
Ciera 2858 Command Bridge • Owner’s Manual Supplement
4
CHAPTER 1: WELCOME ABOARD!
Carbon Monoxide (CO)
!
DANGER!
CARBON MONOXIDE POISONING HAZARD! Carbon monoxide gas (CO) is colorless, odorless, and extremely dangerous. All
engines, generators, and fuel burning
DANGER
appliances produce CO as exhaust. Direct and prolonged exposure to CO will cause
BRAIN DAMAGE or DEATH. Signs of CO poisoning include headache, nausea,
dizziness, and drowsiness.
CO poisoning causes a significant number of boating deaths each year. Called the "silent killer", CO is an extremely
toxic, colorless, odorless and tasteless gas. Breathing CO blocks the ability of your blood to carry oxygen. The effects
are cumulative, even low levels of exposure can result in injury or death. Factors increasing the effects of CO
include: age, smokers or people exposed to high concentrations of cigarette smoke, consumption of alcohol, lung disorders, heart problems, and pregnancy.
Sources of CO
Sources of CO include:
a. Using the engine or the
generator when the boat is
moored in a confined space.
b. Mooring close to
another boat that
is using its engine,
generator or any
other CO source.
c. Running the boat with
the trim angle of the
bow too high.
d. Running the boat
without through
ventilation (station wagon effect).
To correct stationary situations a and/or b:
• Close all windows, portlights and hatches.
• If possible, move your boat away from the source of the CO.
To correct running situations c and/or d:
• Trim the bow down.
• Open windows and canvas.
• When possible, run the boat so that the prevailing winds will help dissipate the exhaust.
IMMEDIATELY take corrective action if CO is detected (see, Carbon Monoxide Alarm System, on the next page).
Ciera 2858 Command Bridge
• Owner’s Manual Supplement
CHAPTER 1: WELCOME ABOARD!
5
Carbon Monoxide Alarm System
Your boat may feature a carbon monoxide (CO) alarm system. DO
NOT DISCONNECT THE ALARM SYSTEM. Read and understand
the manufacturer’s instructions for your CO alarm system. If you did
not receive an instruction manual, call (800) 383-0269 and one will be
mailed to you. If your boat is not equipped with a carbon monoxide
alarm, consider purchasing one from your dealer or marine supply store.
MARINE TECHNOLOGIES INC.
CARBON MONOXIDE ALARM - MODEL 60-541
(REPLACE AFTER TEN YEARS OF USE)
What To Do If Carbon Monoxide Is Detected
• Immediately ventilate and evacuate any enclosed spaces that are
occupied by people and reset your CO alarm.
• Immediately move anyone showing any symptoms of CO poisoning
into fresh air. See a doctor if any symptoms persist. If the person is
unconscious, immediately administer oxygen or CPR and call for
emergency help.
Ciera 2858 Command Bridge • Owner’s Manual Supplement
6
CHAPTER 2:
FEATURES / SYSTEMS
Dimensions and Tank Capacities
Overall
Length
Bridge
Clearance
Beam
Draft
(Drive Up)
Fuel Capacity
(gal)
Freshwater
Capacity (gal)
Waste Holding Tank
Capacity (gal)
30' 6"
10' 3"
9' 10"
1' 8"
113
34
26
Layout View
Hull Exterior Hardware & Drains
WATER TANK
VENT
GALLEY SINK
DRAIN
STARBOARD SIDE
VIEW
ANCHOR
WELL DRAIN
BOW
EYE
AFT BILGE
PUMP DRAIN
HEAD SINK
DRAIN
FWD BILGE
PUMP DRAIN
AIR/COND
OVERBOARD
SHOWER
SUMP DRAIN
ANCHOR
LOCKER
DRAIN
HOLDING
TANK VENT
PORT SIDE
VIEW
SWIM STEP
FUEL TANK VENT
TRANSOM
VIEW
STERN EYES
DECK
DRAIN
TRIM TABS
MACERATOR OVERBOARD
DISCHARGE (OPTION)
GARBOARD DRAIN
Ciera 2858 Command Bridge • Owner’s Manual Supplement
CHAPTER 2: FEATURES / SYSTEMS
7
Quick Oil Drain System
To drain the engine oil:
1. Remove the boat from the water.
2. Unscrew the garboard drain plug.
3. Pull the draw cord until the oil drain plug and the oil drain hose slide out of the garboard drain.
4. Place the end of the oil drain hose into a suitable container.
5. Unscrew the oil drain plug and drain the engine oil.
6. Replace the oil drain plug.
7. Push the drain hose back into the bilge.
8. Replace the garboard drain plug.
Always dispose of waste oil in accordance with local regulations.
QUICK OIL DRAIN SYSTEM
TRANSOM
OIL DRAIN HOSE
OIL DRAIN PLUG
ENGINE OIL PAN
GARBOARD
DRAIN PLUG
DRAW
CORD
BILGE
GARBOARD
DRAIN
Ciera 2858 Command Bridge • Owner’s Manual Supplement
8
CHAPTER 2: FEATURES / SYSTEMS
Deck Hardware and Accessories
ROPE LOCKER
WINDLASS SWITCHES
ANCHOR WINDLASS (OPTION)
WASTE PUMP
OUT FITTING
AFT DECK
STORAGE AREA
DECK CLEAT (TYPICAL)
WATER FILL
FITTING
SHORE POWER CONNECTIONS
(DUAL OPTION SHOWN)
FUEL FILL
FITTING
Ciera 2858 Command Bridge
• Owner’s Manual Supplement
CHAPTER 2: FEATURES / SYSTEMS
9
H e lm L ayo u t (C o m m a n d B r i d g e )
VIEW OF COMMAND BRIDGE HELM LOOKING FORWARD
OIL PRESSURE
GAUGE
TEMPERATURE
GAUGE
TACHOMETER
SPEEDOMETER
DEPTH SOUNDER
GAUGE (OPTION)
VOLTAGE
GAUGE
ENGINE
HOUR METER
COMPASS
(OPTION)
SHIFT/THROTTLE
LEVERS
TRIM TAB
SWITCHES
WINDLASS
SWITCH
(OPTION)
FIRE SUPPRESSION
SYSTEM INDICATOR
LIGHT (OPTION)
MACERATOR
CONTROLS
(OPTION)
VHF RADIO
(OPTION)
ACCESSORY SWITCHES
3
4
5
6
7
TYPICAL HELM LAYOUT SHOWN
ACTUAL LAYOUT MAY VARY DEPENDING
ON ENGINE AND ACCESSORY OPTIONS
1
2
1
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
8
9
10 11 12
ENGINE IGNITION
ENGINE STOP
BILGE BLOWERS
FWD BILGE PUMP
AFT BILGE PUMP
NAVIGATION LIGHTS
ANCHOR LIGHT
HORN
INSTRUMENT LIGHT
COURTESY LIGHTS
DEPTH SOUNDER
ACCESSORY
Ciera 2858 Command Bridge • Owner’s Manual Supplement
10
CHAPTER 2: FEATURES / SYSTEMS
Lifting Sling Locations
Use the following lifting sling locations when raising your boat in or out of the water.
CAUTI ON!
!
PRODUCT OR PROPERTY DAMAGE HAZARD!
When lifting any boat always use a spreader bar. The spreader bar must be equal to the width
of the boat at the lifting point. Always secure the slings to one another to prevent the forward
sling from sliding up along the forefoot of the boat.
Lifting sling positions shown on this drawing
are typical for port and starboard sides.
8 1/2"
LIFTING SLING LABEL
(TYPICAL, TWO LABELS PER SIDE)
46"
Windshield Wiper
• The windshield wiper control switch is located at the helm.
• Periodically, the wiper blade will need to be replaced using 18” blade refills.
To improve visibility; keep your windshield clean and regularly apply a good quality anti-rain solution to the exterior
panes and an anti-fog solution to the interior panes.
Ciera 2858 Command Bridge
• Owner’s Manual Supplement
CHAPTER 2: FEATURES / SYSTEMS
11
Electrical System
Read and understand this section and the electrical section of the owner’s manual. Electrical routing drawings are
provided in Chapter 3 of this supplement; wiring schematics in Chapter 4.
!
•
•
•
•
•
DANGER!
EXTREME FIRE, SHOCK & EXPLOSION HAZARD!
To minimize the risks of fire and explosion, NEVER install knife switches or other arcing
devices in the fuel compartments.
NEVER substitute automotive parts for marine parts. Electrical, ignition and fuel system
parts were designed and manufactured to comply with rules and regulations that minimize
risks of fire and explosion.
DO NOT modify the electrical systems or relevant drawings.
Only qualified personnel should install batteries and/or perform electrical system
maintenance.
Insure that all battery switches are turned OFF before performing any work in the engine
spaces.
!
WARNING!
FIRE, OPEN FLAME & EXPLOSION HAZARD!
• Fuel fumes are heavier than air and will collect in the bilge areas where they can be accidently ignited. Visually and by smell (sniff test), check the engine and fuel compartments for
fumes or accumulation of fuel. ALWAYS operate the bilge blowers for at least four minutes
prior to engine starting, electrical system maintenance or activation of electrical devices.
• Minimize the danger of fire and explosion by not exposing batteries to open flame or sparks.
It is also important that no one smoke anywhere near the batteries.
!
CAUTI ON!
SHOCK & ELECTRICAL SYSTEM DAMAGE HAZARD! NEVER disconnect the
battery cables while the engine is running since it can cause damage to your boat’s
electrical system components.
NOTICE
Electrical connections are prone to corrosion. To reduce corrosion caused electrical problems,
keep all electrical connections clean and apply a spray-on protectant that is designed to protect
connections from corrosion.
Ciera 2858 Command Bridge • Owner’s Manual Supplement
12
CHAPTER 2: FEATURES / SYSTEMS
12 Volt DC System
Fuses and Circuit Breakers
The engine is protected by a large circuit breaker located on the engine. The accessories are protected by circuit
breakers on the battery switch panel and by the accessory circuit breakers located below the steering wheel. Wires are
color-coded to indicate which accessory each fuse services. Some items, such as radios and bilge pumps, may be
fused individually at the unit. Autofloat switches are fused at the battery.
Batteries
The batteries supply electricity
for lights, accessories and engine
starting.
The Electrical section of Chapter 8,
in the Owner’s Manual, provides battery, care and maintenance instructions.
Battery Switch
VOLTMETER
AFT
M
SO
AN
R
T
PORT
The battery switch (located in the aft
deck storage area) has four (4) positions (see photograph on right);
ENGINE
BATTERY
COMPARTMENT
LOCATIONS
• Position "1" - Provides power for
engine starting and accessories,
from battery "1". Battery "1"
(only) will be charged by the
THE BATTERY SWITCH IS
LOCATED IN THE TRANSOM
engine alternator when the engine
STORAGE LOCKER
is running at high idle or faster.
• Position "2" - Provides power for
engine starting and accessories,
from battery "2". Battery "2"
POSITION "BOTH"
ACTIVATES BOTH
(only) will be charged by the
BATTERIES
engine alternator when the engine
is running at high idle or faster.
POSITION "1"
POSITION "2"
ACTIVATES
ACTIVATES
• Position "BOTH" - If batteries are
BATTERY "1"
BATTERY "2"
low; provides power for engine
starting from both batteries. The
"OFF"
"BOTH" position also allows the
POSITION
charging of both batteries by the
engine alternator when the engine
is running at high idle or faster.
• The battery switch should be switched to the "OFF" position whenever the boat is left unoccupied for long periods
of time.
Ciera 2858 Command Bridge
• Owner’s Manual Supplement
CHAPTER 2: FEATURES / SYSTEMS
13
Table 1: Battery Switch Positions
Battery Switch
Position
Accessories
and Lights
Engine Starting
Engine Alternator
Battery Charger
POSITION
"1"
Battery "1"
Provides Starting Power
Provides Power
From Battery "1"
Charges
Battery "1"
Charges
"BOTH"
Batteries
POSITION
"2"
Battery "2"
Provides Starting Power
Provides Power
From Battery "2"
Charges
Battery "2"
Charges
"BOTH"
Batteries
"BOTH"
POSITION
Both Batteries
Provide Starting Power
Both Batteries Provide
Accessory Power (not
advised
unless engine is running)
Charges
"BOTH"
Batteries
Batteries will
NOT
Charge Properly
Battery Charger
Your boat is equipped with a battery charger. Thoroughly read and understand the battery charger manual before
using the charger.
• The battery charger will charge the boat’s batteries whenever the boat is plugged into 120 volt shore power.
• For proper charging; turn the battery switch to any position except "BOTH".
!
CAUTI ON!
The battery charging systems (alternators and battery charger) are designed to charge conventional lead-acid batteries. Before installing gel-cell (or other new technology) batteries, consult
with the battery manufacturer about charging systems requirements.
Ciera 2858 Command Bridge • Owner’s Manual Supplement
14
CHAPTER 2: FEATURES / SYSTEMS
Shore Power/110 Volt AC System
TYPICAL
SHORE POWER
RECEPTACLE
! CAUTION
WATER HEATER DAMAGE HAZARD! - Do not energize the water heater electrical circuit until the heater is COMPLETELY filled with water. The tank is full if
water flows from the tap when the hot water is turned on in the galley. Even
momentary operation in a dry tank will damage the heating elements. Warranty
replacements WILL NOT be made on elements or tank damaged in this manner.
STARBOARD SIDE
OF COCKPIT
SHORE POWER
INLETS
SINGLE INLET
STANDARD
DUAL INLETS
WITH AIR/COND
(OPTION)
!
•
•
•
•
•
•
•
•
•
•
SHORE POWER INLETS
DANGER!
FIRE, EXPLOSION & SHOCK HAZARD!
DO NOT alter shore power connectors and use only compatible connectors.
Before connecting or disconnecting the shore power cord to your boat, verify all breakers
and switches on the AC master panel are turned OFF.
To prevent shock or injury from an accidental dropping of the “hot” cord into the water,
ALWAYS attach the shore power cord to the boat inlet first; then to the dockside connection.
When disconnecting from shore power, disconnect the shore power cord from the dockside
connection first.
NEVER leave a shore power cord connected to the dockside connection only.
Only use shore power cords approved for marine use. NEVER use ordinary indoor or outdoor extension cords that are not rated for marine use.
!
•
AFT
CAUTI ON!
FIRE, SHOCK & ELECTRICAL SYSTEM DAMAGE HAZARD!
NEVER connect dockside power to your boat outside North America unless you have purchased the international electrical conversion option.
The simultaneous use of several AC components can result in an overloaded circuit. It may
be necessary to turn off one or more accessories in order to use another accessory.
Use double insulated or three-wire protected electrical appliances whenever possible.
Periodically check the shore power cord(s) for deterioration or damage. Damaged or faulty
cords should NEVER be used since the danger of fire and electrical shock exists.
DO NOT pinch shore power cords in doors or hatches, or coil the shore power cord too
tightly since these situations can generate enough heat to result in a fire.
If a shore power cord should accidently become immersed in water, THOROUGHLY dry
the blades and contact slots before reusing.
Ciera 2858 Command Bridge
• Owner’s Manual Supplement
CHAPTER 2: FEATURES / SYSTEMS
15
NOTICE
Some dockside installations may be rated less than 30 amps, therefore, you may need to purchase lower amp adapters. Whenever a lower amp adapter is used, however, there will be a corresponding drop in supplied power from the dockside system.
Connecting to Shore Power
1.
2.
3.
Monitor the AC panel’s polarity indicator lights (next to the line 1 and line 2 master breakers) as follows:
• A GREEN light illuminating after the power cord is plugged into the boats external power receptacle indicates acceptable electrical power in which you may energize the main breaker switches.
• A RED light, however, indicates reversed polarity, which could cause electrical system damage and possibly electrical shock injuries. In this case, DO NOT energize the main breaker switches (see warning
below).
Activate the AC system by turning the main ship/shore breaker to the “DOCKSIDE” position.
Turn ON the master breakers and individual component breakers as required.
!
WARNING!
SHOCK & ELECTRICAL SYSTEM DAMAGE HAZARD!
• Monitor the polarity indicator lights EVERY TIME you connect to shore power.
• When connecting to shore power and you encounter a reversed polarity light (RED), DO
NOT energize the main breaker switches. Instead, IMMEDIATELY disconnect the shore
power cord (ALWAYS from the dockside receptacle first) and notify marina management.
NOTICE
The voltage on each line can be read by setting the voltmeter selector switch.
Navigation & Communication Equipment
The owner’s packet contains operation manuals for all navigation & communication equipment installed on your
boat. Thoroughly read and understand these manuals before using these systems. Additionally, read the warnings
below carefully and follow all safety recommendations.
VHF Radio (Option)
Your boat may include an optional VHF (Very High Frequency) radio at the helm. The VHF radio can be used to
access weather reports, summon assistance or contact other vessels as permitted by the FCC (Federal Communications Commission). Be sure to contact the FCC for licensing, rules and regulations concerning VHF radio usage.
Compass (Option)
NOTICE
Compass accuracy can be affected by many factors. Have a qualified technician calibrate your
compass. Make sure the technician gives you a deviation card which shows the corrections to
apply in navigational calculations. Keep a copy of the deviation card at the helm.
Ciera 2858 Command Bridge • Owner’s Manual Supplement
16
CHAPTER 2: FEATURES / SYSTEMS
Depth Finder (Option)
!
WARNING!
• DO NOT use the depth finder as a navigational aid to prevent collision, grounding, boat
damage or personal injury.
• When the boat is moving, submerged objects will not be seen until they are already under
the boat. Bottom depths may change too quickly to allow time for the boat operator to react.
If you suspect shallow water or submerged objects, operate the boat at very slow speeds.
Audio Equipment
The audio equipment installed on your boat has separate manuals (included in your boat’s owner’s packet) that
explains its operating procedures in detail.
NOTICE
AM radio reception may be impaired in areas where reception is limited or anytime the engine
is running.
Lighting
Navigation and Interior Lights
Read and understand the navigation light section of the owner’s manual. The navigation and interior lights installed
on your boat are of top quality, but you should be aware that failure may periodically occur for a variety of reasons:
1.
2.
3.
4.
There may be a blown fuse - replace the fuse.
The bulb may be burned out - carry spare bulbs for replacement.
A wire may be damaged or may have come loose - repair as required.
The bulb base may be corroded - clean the base and coat it with non-conductive electrical lubricant.
!
CAUTI ON!
• Avoid the storage of gear where it would block navigation lights from view.
• Be conservative in the use of battery power. Prolonged operation of cabin interior lights
(overnight) will result in a drained battery.
Ciera 2858 Command Bridge
• Owner’s Manual Supplement
CHAPTER 2: FEATURES / SYSTEMS
17
Appliances
All appliances installed on your boat come with their own manuals that contain detailed operating instructions and
important safeguards. Thoroughly read and understand these manuals before operating your boat’s appliances.
• Make sure the AC breaker is activated for the appliance you wish to turn on.
NOTICE
Always keep an approved ABC-type fire extinguisher in galley area.
!
WARNING!
FIRE/PERSONAL INJURY HAZARD
Before each use of the galley stove, the lower helm seat’s back rest MUST be lowered into the
counter top position to reduce the possibility of fire or injury (see drawing below).
GALLEY
HELM SEAT; RAISED IN
BACK REST POSITION
LOWER
HELM
STOVE
HELM SEAT
LOWERED IN
COUNTER TOP
POSITION
Ciera 2858 Command Bridge • Owner’s Manual Supplement
18
CHAPTER 2: FEATURES / SYSTEMS
Propulsion
Engine
The owner’s packet contains detailed engine operation and maintenance manuals. Be sure to read and understand
these manuals before operating or performing maintenance to the engine.
Fuel System
TRANSOM
Fuel Fill and Vent:
AFT
The fuel fill is located on the starboard
aft deck. The fuel fill fitting is marked
“GAS”. The fuel tank vent is located in
the hull below and in the same general
area as the fill.
If you experience difficulty filling the
fuel tank, check to see that the fuel fill
and vent lines are free of obstructions
and kinks.
FUEL FILL
DECK FITTING
FUEL SYSTEM ROUTING
Fuel Filters:
FUEL TANK
All tanks are equipped with a fine
mesh screen filter on the fuel pickup
tube (located inside or on the outside
of the tank) to the fuel line fitting. In
addition, when supplied by the engine
manufacturer, a filter is installed on the
engine.
Replace the fuel filter periodically to
ensure they remain clean and free of
debris. Consult your selling dealer or
local marina concerning fuel additives
that help to prevent fungus or buildup
in your fuel tank.
FUEL FILL
DECK FITTING
FUEL FEED
HOSE
AFT
FUEL TANK
VENT FITTING
VIEW OF THE ENGINE
COMPARTMENT
Anti-siphon Valve:
Your boat is equipped with an anti-siphon valve, which is an integral part of the barb fitting on the fuel tank in which
the neoprene fuel line attaches. The valve is spring loaded and is opened by fuel pump vacuum. These valves will prevent fuel from siphoning from the tank in the event of a fuel line rupture.
NOTICE
If an engine running problem is diagnosed as fuel starvation, check the anti-siphon valve. In the
event the valve is stuck or clogged, it should be changed or replaced while the engine is shut down.
Under NO circumstances should the anti-siphon valve be removed, except in an emergency.
!
WARNING!
FIRE/EXPLOSION HAZARD - It is very important that the fuel system be
inspected thoroughly the first time it is filled and at each subsequent filling. For
your safety and the safety of your passengers, the fueling instructions in the
Owner’s Manual must be carefully followed.
!
CAUTI ON!
Avoid the storage or handling of gear near the fuel lines, fittings and tank.
Ciera 2858 Command Bridge
• Owner’s Manual Supplement
CHAPTER 2: FEATURES / SYSTEMS
Bilge Blower
• The bilge blower removes fumes from the engine
compartment and draws fresh air into the compartment through the deck vents.
• To ensure fresh air circulation, operate the bilge
blower for at least four minutes before starting the
engine, during starting, and while operating the boat
below cruising speed.
STBD
BILGE BLOWER
SYSTEM
ENGINE
COMPARTMENT
BLOWER HOSES
TO/FROM DECK
LOUVERS
AFT
!
19
BLOWER
WARNING!
EXPLOSION HAZARD!
• Operation of the blower system is not a guarantee that explosive fumes have been
removed. If you smell fuel, DO NOT start the engine. If the engine is already running,
IMMEDIATELY shut OFF the engine and all electrical accessories and investigate.
• DO NOT obstruct or modify the ventilation system.
Ciera 2858 Command Bridge • Owner’s Manual Supplement
20
CHAPTER 2: FEATURES / SYSTEMS
Trim Tabs
Trim tabs control the longitudinal and lateral trim of your boat at
cruising speeds and are controlled by two rocker switches,
located at the helm station. Before using the trim tab switches,
we strongly urge you to read and understand the trim tab operation manual included in your boat’s owner’s packet and observe
the following:
• Once the best bow cruising trim is reached, use the port or
starboard trim switches, one at a time, to correct unequal lateral loading.
• Trim tab adjustment should be performed by several short
touches to the switch rather than one long one. After each
short touch allow about five seconds for the hull to react.
• The trim tab hydraulic fluid reservoir is located in the engine
compartment. The fluid level should be checked periodically
(at least once a year) and refilled as necessary.
VIEW OF THE HELM
TRIM TAB SWITCH
TRIM TAB
COMPONENTS
TRANSOM
!
WARNING!
LOSS OF CONTROL HAZARD!
• Improper use of trim tabs may cause loss of control! DO
NOT use trim tabs in a following sea as they may cause
broaching or other unsafe handling characteristics.
• NEVER allow anyone unfamiliar with trim tabs to
operate them and DO NOT use trim tabs to compensate
for excessive unequal weight distribution.
TRIM TAB
(TYPICAL)
Bilge Pumps
Your boat is equipped with two impeller-type bilge pumps. The bilge pumps are automatically controlled by float
switches (see "Autofloat Switches" on the next page). The bilge pumps can also be controlled by switches
on the dash.
THE AFT BILGE PUMP IS LOCATED UNDER THE ENGINE
THE FWD BILGE PUMP IS LOCATED UNDER THE CABIN FLOOR
STBD
THRUHULL
AFT BILGE PUMP
& FLOAT SWITCH
Ciera 2858 Command Bridge
THRUHULL
FWD BILGE PUMP
& FLOAT SWITCH
• Owner’s Manual Supplement
AFT
CHAPTER 2: FEATURES / SYSTEMS
21
NOTICE
Discharge of oil, oil waste or fuel into navigable waters is prohibited by law. Violators are subject to legal action by the local authorities.
Bilge Pump Testing
Check the bilge pump often to make sure it is working
properly. To check the bilge pump:
• Turn on the dash-mounted switch and make sure that water in the bilge is pumped overboard.
If bilge water is present and the pump motor is running but not pumping:
• Inspect the bilge pump hose for a kink or collapsed area.
• If the bilge pump hose is not the problem, check the bilge pump housing for clogging debris:
Bilge Pump Cleaning:
1.
Remove the power cartridge:
a. Lift the tab while rotating the fins counterclockwise.
b. Lift out the power cartridge.
c. Clear the outer housing of debris.
2. Reinstall the power cartridge:
a. Make sure the “O” ring is properly seated.
b. Coat the “O” ring with a light film of vegetable or mineral oil.
c. Align the two cams on either side of the power cartridge with
the two slots on the outer housing and press the power cartridge into the housing while twisting clockwise.
d. To ensure proper reinstallation of the power cartridge, attempt
to twist the fins counterclockwise without lifting the tab: The
cartridge should stay in place.
BILGE PUMP
COMPONENTS
TAB
“O” RING
FIN
OUTER
HOUSING
Autofloat Switches
LIGHT
Automatic bilge pumps use electromagnetic float (autofloat)
CAM
POWER
FILM
(TYPICAL)
switches to automatically activate the pump whenever water rises
CARTRIDGE
OF OIL
above a preset level in the bilge. One autofloat switch is mounted
next to the bilge pump it activates, and is wired directly to the battery so it will normally function even when the boat is completely shut down and left unattended.
Autofloat switches should be tested often for proper operation as follows:
SLOT
(TYPICAL)
Float Switch Test:
1.
Push the float switch test button up to activate
the bilge pump.
If the pump does not turn on, check the inline fuse.
If the fuse is good but the switch doesn’t work, it
may indicate a bad switch or a low battery.
2. Push the test button all the way down to return
the float switch back into the auto mode.
!
CAUTION!
After testing a float switch, you must push the
test button all the way down to the auto position
to turn the switch back into auto mode!
FLOAT SWITCH
TESTING
FLOAT SWITCH
TEST BUTTON
FLOAT UP - TEST MODE
BILGE PUMP SHOULD TURN ON
FLOAT DOWN - AUTO MODE
BILGE PUMP SHOULD TURN OFF
Ciera 2858 Command Bridge • Owner’s Manual Supplement
22
CHAPTER 2: FEATURES / SYSTEMS
Freshwater System
Your boat is equipped with a pressure-demand freshwater (potable)
system. These pressure type (demand) systems operate when the water
pump switch next to the AC panel is in the ON position.
• The water pump’s DC breaker must be turned ON to
use freshwater.
• The water pump’s DC breaker should be turned OFF when any of
the following occurs:
✓ When the boat is not in use.
✓ Whenever the water tank is empty.
• The water tank fill fitting is located on the starboard deck, forward
of the louver (see illustration on the right).
• When your boat is to be left unattended for long periods of time,
pump the water tank dry to prevent stored water from becoming
stagnant and distasteful. Should it become necessary to disinfect
the freshwater system, ask your dealer about treatments available
for your boat’s system.
• Inspect and clean the water filter, located on the water pump, often.
• The water tank is located below the salon floor.
THE AC PANEL IS LOCATED
IN THE STARBOARD CABIN
PUMP
SWITCH
12 VOLT
RECEPTACLE
AC PANEL
WATER TANK FILL
LOCATION
Water Heater
• The water heater is located on the aft port side of the bilge.
• The water heater is connected to the AC power system, therefore,
you must verify that the water heater breaker on the AC panel is
turned ON before water will be heated.
• Read the manufacturer’s instruction manual supplied in your boat’s
owner’s packet and observe the following warnings.
WATER TANK
FILL FITTING
WATER LINE ROUTING
FROM WATER TANK
WATER
HEATER
FITTING FOR
COLD WATER
LINE
FITTING FOR
HOT WATER
LINE
STBD
PUMP
WATER LINE
TO HEAD
WATER
PUMP
WATER LINE
TO GALLEY
TANK
WATER TANK
FILL FITTING
WATER PUMP AND WATER
TANK ACCESS THROUGH
WALL AND FLOOR CUTOUTS
WATER TANK
VENT FITTING
WATER
TANK
Ciera 2858 Command Bridge
FWD
• Owner’s Manual Supplement
CHAPTER 2: FEATURES / SYSTEMS
23
WARNING!
!
HOT HAZARD! Water heated by the water heater can reach temperatures high enough
to scald the skin.
CAUTI ON!
!
WATER HEATER DAMAGE HAZARDS!
• DO NOT energize the AC water heater electrical circuit until the heater is completely filled
with water. Even momentary operation in a dry tank will damage the heating elements.
Warranty replacements will not be made on elements or tank damaged in this manner. The
tank is full if water flows from the tap when the hot water is turned on in the galley.
• The water heater should be drained and the power turned OFF when the possibility of
freezing exists.
Sink & Shower Drain Systems
Gray water (water from sinks and showers)
above the waterline is gravity drained overboard, while gray water below the waterline is pumped overboard using a sump
pump.
The sump box (A), containing the shower
sump pump, float switch, and filter is
located under the middle entry step (B) (see
the illustration on the right).
Sump Box Cleaning
The sump box, filter, and pump should be
periodically cleaned of debris as follows:
1.
2.
3.
Remove the cover screws (C) and
the cover (D).
Remove any debris from the box and
the filter.
Clean the sump pump as outlined in
the bilge pump section of
this Supplement.
SUMP PUMP ACCESS
D
C
Sump System Winterization
Drain the sump pump system in the winter
months when not in use.
1.
2.
3.
Disconnect and drain all lines to
the unit.
Remove the screws from the mounting
feet (E) and drain the system.
Reinstall the screws in the mounting
feet and reconnect the system.
E
A
Ciera 2858 Command Bridge • Owner’s Manual Supplement
24
CHAPTER 2: FEATURES / SYSTEMS
Raw Water System
Seacocks
Seacocks are valves which are typically used to manage the intake of raw water
through the hull below the water line (raw water intake seacocks). Seacocks may
also be used to discharge waste or water through the hull below the water line (discharge seacocks).
Seacocks are controlled by a 90º lever and are used on your boat in the following
raw water intake/discharge systems: Engine, (optional) air conditioning system
and (optional) marine head (toilet) system.
!
TYPICAL RAW WATER INTAKE
SEACOCK COMPONENTS
90º
SEACOCK
LEVER
HULL
SECTION
SEACOCK
GASKET
INTAKE
STRAINER
CAUTION!
SYSTEM DAMAGE HAZARD! Verify that the system’s seacock is OPEN before the system is
started and keep the seacock open until the system is shut off. Close seacocks whenever the
systems will not be used for long periods of time
Raw Water Strainers
Raw water strainers are used in water pickup systems to filter incoming raw water. The typical layout is one strainer
for each of the following: Engine, and optional air conditioning system. Raw water strainers are located near raw
water intake valves (seacocks) and should be checked every time you use your boat for leaks and/or debris. If debris
is found, clean the raw strainer as follows:
!
CAUTION!
• FLOODING HAZARD! The seacock that sends raw water to the strainer must be
CLOSED before disassembling the raw water strainer to prevent the boat from taking on
water through the raw water strainer assembly. Keep the seacock CLOSED until the raw
water strainer is completely reassembled.
• SYSTEM DAMAGE HAZARD! After reassembling the raw water strainer, verify that the
seacock valve is OPEN before energizing the component/system.
1.
2.
3.
4.
5.
6.
7.
Make sure the component/system (engine, air conditioning) that the strainer is connected to is turned OFF.
Close the seacock that sends raw water to the strainer you are about to clean. The seacock must remain closed
until the strainer is completely reassembled.
Take apart the raw water strainer.
Remove debris.
Flush strainer with water.
Reassemble the raw water strainer.
Open the seacock and check for leaks around the strainer. If no leaks are found, you may activate the component
or system.
Ciera 2858 Command Bridge
• Owner’s Manual Supplement
CHAPTER 2: FEATURES / SYSTEMS
25
Marine Head with Holding Tank
Your boat comes equipped with a marine head
(toilet) and waste holding tank system. Be sure
to read the manufacturer’s operation and maintenance manual (included in your boat’s owner’s
packet).
• The marine head installed on your boat uses
seawater to flush waste from the toilet. The
seawater intake valve (seacock) is located
under the forward floor hatch in the main
cabin.
• Waste is routed directly from the head to the
holding tank.
• The holding tank is plumbed to a fitting on
the deck for dockside pump-out.
• You can determine the content level of the
holding tank by looking at the tank located
under the forward floor hatch in the main
cabin. We advise emptying the holding tank at
every opportunity.
• If you are unable to pump water into the bowl,
the probable cause is debris in the pump diaphragm. To remedy this, shut off the seawater
intake valve (seacock) and dismantle the
pump. The pump is generally held together
with six screws (the design is simple and the
problem will be obvious when the pump body
is split open).
To winterize the head, shut off the intake seacock
and pump until the bowl is dry. Remove the drain
plug in the base and pump again to remove all of
the water. Do not fill the bowl with anti-freeze.
The intake seacock should be left closed while
the boat is underway or whenever the boat is left
moored in the water.
HEAD PICKUP LOCATED
IN THE ENGINE ROOM
MARINE HEAD SYSTEM
MARINE
HEAD
HOSE TO
MARINE
HEAD
MARINE
HEAD
PICKUP
HOSE TO
HOLDING
TANK
HOLDING
TANK
AFT
HOSE TO
HOLDING
TANK VENT
WASTE PUMP
OUT FITTING
MACERATOR SYSTEM (OPTION)
HOLDING
TANK
MACERATOR
Operating the manual flush marine head:
1.
Open the head’s seawater intake valve (seacock).
2. Before using the head, pump enough water
into the bowl to wet the sides.
After use, pump until the bowl is thoroughly
cleaned. Continue pumping a few more times
to clean the lines. If excess waste causes the
water to rise in the bowl, stop pumping until the
water recedes.
OVERBOARD
DISCHARGE
SEACOCK
STBD
AFT
FROM TANK TO
MACERATOR
NOTICE
Check with local authorities for regulations regarding the legal use of marine head systems.
Ciera 2858 Command Bridge • Owner’s Manual Supplement
26
CHAPTER 2: FEATURES / SYSTEMS
Air Conditioning System (Option)
Your boat may be equipped with an optional air conditioning system. Please refer to the air conditioner manual for
detailed operating instructions.
• Before operating the air conditioning system, make sure the breakers on the AC main distribution panel are activated and verify the system’s raw water pickup seacock is OPEN. The seacock must remain OPEN anytime the air
conditioner is in use.
• The raw water pickup strainer should be checked periodically for debris according to the directions given in the
Raw Water Strainer section of this supplement.
!
CAUTI ON!
SYSTEM DAMAGE HAZARD! The air conditioning system’s seacock must be OPENED before
turning on an air conditioning unit and must remain open during operation.
AIR CONDITIONING UNIT
AIR CONDITIONING SEACOCK
AIR CONDITIONING
SEAWATER STRAINER
AIR CONDITIONING ROUTING
Ciera 2858 Command Bridge
• Owner’s Manual Supplement
27
CHAPTER 3:
ELECTRICAL ROUTINGS
WINDLASS CIRCUIT BREAKER
Hull Wire Harness Routings
TO BATTERY
TRIM
PUMP
AFT BERTH
READING
LIGHT
MACERATOR
FWD BILGE
PUMP
BATTERY SWITCH
BATTERY
CHARGER
HEAD
PICKUP
GROUND
TRIM TABS
FUEL TANK
SENDER
STEP
LIGHT
ENGINE
GROUND
AFT BILGE
PUMP
ENGINE
WATER
PUMP
BLOWER
LIGHT
SWITCHES
SHOWER
SUMP
FUEL FILL
GROUND
FWD TO
LOWER
HELM
TO WINDLASS MAIN SWITCH AND
HELM REMOTE SWITCH (OPTION)
TO UPPER
HELM
FROM WINDLASS MAIN SWITCH AND
HELM REMOTE SWITCH (OPTION)
TO WINDLASS AND
DECK SWITCHES
AFT BERTH
LIGHT
COURTESY
LIGHT
READING
LIGHTS
GALLEY WATER
PUMP SWITCH
TO LOWER
HELM
Ciera 2858 Command Bridge • Owner’s Manual Supplement
28
CHAPTER 3: ELECTRICAL ROUTINGS
Deck Wire Harness Routings
NOTE: VIEW IS OF THE UNDERSIDE OF THE MID DECK
BOW
LIGHT
TO WINDLASS, RELAY
& DECK SWITCHES
HORN
V - BERTH
OVERHEAD
LIGHT
PORT
WIPERS
WIPER
STBD
SPEAKER
WIRES
HALL
LIGHTS
MID BERTH
LIGHT
GALLEY
LIGHTS
DINETTE
LIGHTS
ENGINE HARNESS
ENTRY
LIGHT
COCKPIT
LIGHTS
Ciera 2858 Command Bridge
• Owner’s Manual Supplement
CHAPTER 3: ELECTRICAL ROUTINGS
29
AC Battery Cable Routings
POSITIVE BATTERY CABLE ROUTINGS
TO BATTERY
SWITCH IN
TRANSOM
STORAGE
JUMPER
CABLE
TO STARTER
SOLENOID
ON ENGINE
C
POSITIVE
CABLES
NE ENT
GI
EN R TM
A
P
OM
BATTERIES
AFT
NEGATIVE BATTERY CABLE ROUTINGS
GROUND
BUSS BAR
TO ENGINE
GROUND
PORT
NEGATIVE CABLES
TO NEGATIVE POSTS
ON BATTERIES
BATTERIES
NEGATIVE
JUMPER
CABLE
T
NE N
GI ME
EN AR T
MP
CO
AFT
PORT
Ciera 2858 Command Bridge • Owner’s Manual Supplement
30
CHAPTER 4:
WIRING SCHEMATICS
AC Electrical System Single Dockside
Ciera 2858 Command Bridge • Owner’s Manual Supplement
CHAPTER 4: WIRING SCHEMATICS
31
AC Electrical System Dual Dockside
Ciera 2858 Command Bridge • Owner’s Manual Supplement
32
CHAPTER 4: WIRING SCHEMATICS
TRIM/TAB
SWITCH
Gas Engine Electrical System
Ciera 2858 Command Bridge
• Owner’s Manual Supplement
CHAPTER 4: WIRING SCHEMATICS
33
Diesel Engine Electrical System
Ciera 2858 Command Bridge • Owner’s Manual Supplement
• Owner’s Manual Supplement
3
DISPLAY WIRE (BLACK)
6
7
8
9
12 TO 24 VDC FROM
PORT IGN. (RED/PURPLE)
12 TO 24 VDC FROM
STRBD. IGN. (RED/PURPLE)
12 TO 24 VDC FROM
GEN/BLOWER
5
EXPANDER
AGENT BOTTLE & GROUND
(DO NOT CONNECT TO
ENGINE BLOCK)
4
2
DISPLAY WIRE (WHITE)
AGENT BOTTLE SW. (BROWN)
1
DISPLAY WIRE (BROWN)
NC C
15
AUXILIARY
CIRCUIT #4
NO
NC C
NO
14
K5
AUXILIARY
CIRCUIT #4
13
12
11
10
K4
D1
D2
D3
D4
K5
22
23
24
19
C
PLACE WIRE (WHITE) FROM GEN.
FUEL SOLENOID
NC CNNCT. WIRE (WHITE) HERE TO POWER
DOWN GEN. OR BLOWER MOTOR
17
16
NO PLACE WIRE HERE TO POWER
UP FUEL SOLENOID
18
PLACE WIRE (PURPLE/WHITE) HERE
FROM STRBD. ENGINE FUEL SOLENOID
FIRE WATCH OPTION HOOK UPS TO TERMINAL
BLOCK UNDER DASH.
C = COMMON
NC = NORMALLY CLOSED
NO = NORMALLY OPENED
RELAYS SHOWN IN POWER UP (ENERGIZED) POSITION.
K3
C
NC CONNECT WIRE (PURPLE) HERE TO
POWER DOWN FUEL SOLENOID
20
PLACE WIRE (PURPLE) FROM PORT
ENGINE FUEL SOLENOID
NO PLACE WIRE HERE TO POWER
UP FUEL SOLENOID
C
NC CONNECT WIRE (PURPLE) HERE TO
POWER DOWN FUEL SOLENOID
NO PLACE WIRE HERE TO POWER
UP FUEL SOLENOID
21
CIRCUIT #3
K2
CIRCUIT #2
K1
CIRCUIT #1
FIVE CIRCUIT SHUTDOWN
YE
L
LO
W
Y
E
LL
OW
Ciera 2858 Command Bridge
Y
E
LL
O
YE W
L
LO
W
34
CHAPTER 4: WIRING SCHEMATICS
Fire Suppression System Wiring (Option)
35
LIMITED WARRANTY
Bayliner warrants to the original purchasers of its 2000 and 2001 model boats, purchased from an authorized dealer, operated
under normal, noncommercial use that the selling dealer will: (A) Repair any structural hull defect which occurs within five (5)
years of the date of delivery; and (B) Repair or replace any parts found to be defective in factory material or workmanship within
one (1) year of the date of delivery.
What Is Not Covered
This limited warranty does not apply to:
1. Engines, drive trains, controls, props, batteries, or other equipment or accessories carrying their own individual warranties;
2. Engines, parts or accessories not installed by Bayliner;
3. Plexiglass windscreen breakage; rainwater leakage on runabout models; rainwater leakage through convertible tops; minor
gelcoat discoloration, cracks or crazing or air voids;
4. Hull blisters that form below the waterline;
5. Normal deterioration, i.e. wear, tear, or corrosion of hardware, vinyl, tops, vinyl and fabric upholstery, plastic, metal, wood,
or trim tape;
6. Any Bayliner boat which has been overpowered according to the maximum horsepower specifications on the capacity plate
provided on each Bayliner outboard boat;
7. Any Bayliner boat used for commercial purposes;
8. Any defect caused by failure of the customer to provide reasonable care and maintenance.
Other Limitations
THERE ARE NO OTHER EXPRESS WARRANTIES ON THIS BOAT. TO THE EXTENT ALLOWED BY LAW:
1. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED
TO THE DURATION OF ONE YEAR.
2. Neither Bayliner nor the selling dealer shall have any responsibility for loss of use of the boat, loss of time, inconvenience,
commercial loss or consequential damages.
3. Some jurisdictions do not allow limitations on how long any implied warranty lasts, so the above limitation may not apply
to you. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
Your Obligation
In order to comply with regulations, it is essential that your limited warranty registration card be submitted within 30 days of
delivery of your boat. Return of the limited warranty registration card is a condition precedent to limited warranty coverage.
Before any warranty work is performed, we require that you contact your dealer to request warranty assistance.
YOU MUST GIVE US WRITTEN NOTICE OF YOURWARRANTY CLAIM PRIOR TO THE EXPIRATION OF YOUR
LIMITED WARRANTY AND ALLOW US AN OPPORTUNITY TO RESOLVE THE MATTER.
We require that you return your boat, at your expense, to your selling dealer or, if necessary, to the Bayliner factory.You wil l be
responsible for all transportation, haulouts and other expenses incurred in returning the boat for warranty service.
Bayliner Marine Corporation
PO Box 9029
Everett, WA 98206
Phone: 360-435-8957
FAX: 360-403-4235
Ciera 2858 Command Bridge • Owner’s Manual Supplement
Owner’s Notes
Part Number 110137
Bayliner • P.O. Box 9029 • Everett, WA 98206 • 360-435-5571
Download PDF