Bunn | H5E-DV PC | Service manual | Bunn H5E-DV PC Service manual

H5E-DV PC
H5EA PC
INSTALLATION & OPERATING GUIDE
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
To ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts
Catalog, Programming Manual, or Service Manual, please visit the Bunn-O-Matic website, at
www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and
manual updates. For Technical Service, contact Bunn-O-Matic Corporation at 1-800-286-6070.
39338.0000G 04/09 ©2006 Bunn-O-Matic Corporation
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY
Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:
1) All equipment other than as specified below: 2 years parts and 1 year labor.
2) Electronic circuit and/or control boards: parts and labor for 3 years.
3) Compressors on refrigeration equipment: 5 years parts and 1 year labor.
4) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis:
parts and labor for 3 years or 30,000 pounds of coffee, whichever comes first.
These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by
it will be commercially free of defects in material and workmanship existing at the time of manufacture and
appearing within the applicable warranty period. This warranty does not apply to any equipment, component or
part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect,
alteration, improper installation or operation, improper maintenance or repair, damage or casualty. This warranty is
conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone
at (217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by
BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior
authorization from BUNN that the defective equipment is under warranty.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR
ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN
are not authorized to make modifications to this warranty or to make additional warranties that are binding on
BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and
should not be relied upon.
If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its
exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts
and/or labor (during the applicable parts and labor warranty periods specified above) to repair the defective
components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace
the equipment or refund the purchase price for the equipment.
THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF
THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S
SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.
In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales,
loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute
equipment, facilities or services, or any other special, incidental or consequential damages.
BrewWISE, BrewLOGIC, BrewMETER, BrewWIZARD, Bunn Gourmet, BUNN Gourmet Ice, BUNN Pour-O-Matic, BUNN,
Bunn-OMatic, Bunn-O-Matic, BUNNlink, BUNNserve, BUNNSERVE, BUNN Espress, Cool Froth, DBC, Dr. Brew, Dual, EasyClear, EasyGard, Easy Pour, FlavorGard, Gourmet Ice, Gourmet Juice, High Intensity, IMIX, Infusion Series, Intellisteam,
Quality Beverage Equipment Worldwide, The Mark of Quality in Beverage Equipment Worldwide, My Café, PowerLogic,
Safety-Fresh, Scale-Pro, Silver Series, Single, Smart Funnel, Smart Hopper, SmartWAVE, Soft Heat, SplashGard, System
III, ThermoFresh, 392, AutoPOD, AXIOM, Beverage Profit Calculator, Beverage Bar Creator, BUNNsource, Coffee At Its
Best, Digital Brewer Control, Nothing Brews Like a BUNN, Pouring Profits, Pulse Wave, Signature Series, Smart Heat,
Tea At Its Best, The Horizontal Red Line, Titan, Ultra, are either trademarks or registered trademarks of Bunn-O-Matic
Corporation.
2
39338 012609
INTRODUCTION
This equipment heats and dispenses water on demand for beverages and cooking purposes. It has a panel
above the dispense valve that indicates the status of the dispenser. This equipment is for indoor use, either
wall-mounted or on a sturdy counter or shelf.
USER NOTICES
The notices on this dispenser should be kept in good condition. Replace unreadable or damaged labels.
! WARNING
Very Hot Water
Use With Care!
37881.0000
12593.0000
This equipment must be installed to comply
with the International Plumbing Code of the
International Code Council and the Food
Code Manual of the Food and Drug Administration (FDA). For models installed outside
the U.S.A., comply with the applicable
Plumbing /Sanitation Code.
120V
120/208-240V
34056.0000
00656.0000
00824.0000
Optional Field Wiring
00824.0000
120 V, 15.4 A, 1850 W
1PH, 2-Wire + GND, 60HZ
29710.0017
Optional Field Wiring
120/208-240 V, 16.9 A, 4050 W
1PH, 3-Wire + GND, 60HZ
29710.0018
00831.0000
3
39338 021408
ELECTRICAL REQUIREMENTS
WARNING - The dispenser must be disconnected from the power source until specified in Initial Set-Up.
Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements.
RED
WHI
BLK
GREEN
L2
N
BLK
120V. A.C.
208 or 240V. A.C.
RED
L1
200 or 230V. A.C.
L2
120V. A.C.
L1
GREEN
Earth Ground
P1842
Chassis Ground
120/208 & 120/240V ac
single phase models
230V ac
single phase models
Note: This electrical service
consists of 3 current carrying
conductors (Neutral, L1 and
L2) and a separate conductor
for earth ground.
Note: This electrical service
consists of 2 current carrying conductors (L1 and L2)
and a separate conductor
for earth ground.
Electrical Hook-Up
CAUTION – Improper electrical installation will damage electronic components.
1. An electrician must provide electrical service as specified.
2. Using a voltmeter, check the voltage and color coding of each conductor
at the electrical source.
3. On models equipped with a master switch (right side, lower rear corner),
place it in the “OFF” position, Fig 1.
4. Remove the upper and lower rear panels.
5. On Dual Volt models, make sure the toggle switch below the circuit board
is set to the desired voltage (120 volts or 208/240 volts) and the red switch
on the circuit board is in the "SET" position, Fig 2.
6. Install a strain relief and the proper electrical wiring to the terminal block.
7. Connect the dispenser to the power source and verify the voltage at the
terminal block before proceeding. Reinstall both rear panels.
8. If plumbing is to be hooked-up later be sure the dispenser is disconnected
from the power source. If Plumbing has been hooked-up, the dispenser
is ready for Initial Set
P3744
FIG 1
P3745
FIG 2
4
39338 040309
CE REQUIREMENTS
• This appliance must be installed in locations where it can be overseen by trained personnel.
• For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C.
• Appliance shall not be tilted more than 10° for safe operation.
• An electrician must provide electrical service as specified in conformance with all local and national codes
• This appliance must not be cleaned by water jet.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given instructions concerning use of this appliance by a person responsible for its safety.
• Children should be supervised to ensure they do not play with the appliance.
• If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel with
a special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard.
PLUMBING REQUIREMENTS
This dispenser must be connected to a cold water system with operating pressure between 20 and 90 psi
(138 and 620 kPa) from a 1⁄2" or larger supply line. A shut-off valve should be installed in the line before the dispenser. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345
kPa). The water inlet fitting is ⁄4" flare.
1
NOTE - Bunn-O-Matic recommends ⁄4" tubing for installations of less than 25 feet and ⁄8" for more than 25 feet
from the ⁄2" water supply line. At least 18 inches of an FDA approved flexible beverage tubing, such as reinforced
braided polyethylene or silicone, before the dispenser will facilitate movement to clean the countertop. BunnO-Matic does not recommend the use of a saddle valve to install the dispenser. The size and shape of the hole
made in the supply line by this type of device may restrict water flow.
1
3
1
This equipment must be installed to comply with the International Plumbing Code of the International
Code Council and the Food Code Manual of the Food and Drug Administration (FDA). For models installed
outside the U.S.A., you must comply with the applicable Plumbing/Sanitation Code for your area.
PLUMBING HOOK UP
1. Remove the shipping cap from the fitting on the rear
of the dispenser, Fig 3.
2. Attach the flare elbow fitting (supplied separately with
the dispenser) to the fitting.
3. Flush the water line and securely attach it to the flare
elbow fitting.
4. Turn on the water supply.
P3746
FIG 3
5
39338 040309
INITIAL SET-UP
CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except
when specified in the instructions.
1. Remove the upper panel from the rear of the dispenser.
2. Make sure the toggle switch below the circuit board is set to the desired voltage (120 volts or 208/240 volts)
and the red switch on the circuit board is in the "SET" position.
3. Connect the dispenser to the power source and turn-on the water supply.
4. Place the master switch in the "ON" position.
5. Water will automatically flow into the tank to the proper level and shut-off. This will take approximately 7
minutes.
6. The water will heat to the factory default setting of 200° F (93° C) for most dispensers, and 90° F (32° C) for
other dispensers.
7. Refer to PROGRAMMING to set the tank temperature, ready temperature, and dispense volumes.
DRAINING THE DISPENSER
CAUTION - The dispenser must be disconnected from the power source throughout these steps.
1.
2.
3.
4.
5.
Disconnect the dispenser from the power source.
Shut-off and disconnect the incoming water supply
Remove the 4-40 screws at the sides of the top panel.
Gently remove one of the grommets from the tank lid.
Insert a syphon tube to the bottom of the tank and syphon ALL of the water out.
CLEANING
The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all
surfaces on Bunn-O-Matic equipment.
WALL MOUNTED INSTALLATION
If the dispenser is wall mounted, the bottom of the dispenser should be at the same height as a counter or
table top. Use B.O.M. part #12542.0000 for side mounted Wall Bracket Kit or # 13125.0001 for front mounted
Wall Bracket Kit .
SUPPORT FOR LARGE RECEPTACLES
CAUTION: If the dispenser is to be used with larger receptacles such as pitchers or pots, those receptacles must
be adequately supported during dispensing of hot water to avoid spillage of very hot water. This support may be
provided by a table or counter top, or use B.O.M. part #12599.0000 Shelf Kit.
6
39338 012609
OPERATING CONTROLS
d.
c.
a.
b.
P3743
e.
(a) VOLUME SELECTOR BUTTONS
Press and release the button corresponding to the Small, Medium, or Large volume, to select the desired
amount of water to be dispensed. Pressing a different button after a cycle has been initiated does not change
the volume in progress.
(b)AUTO STOP/MANUAL DISPENSE BUTTON
Press and release button to stop a dispense cycle. Press and hold button to dispense manually.
(c) HIDDEN PROGRAMMING BUTTON
(d)LED INDICATORS
(e)DISPENSE NOZZLE
7
39338 100606
PROGRAMMING
When power is applied to the dispenser, the display located on the bottom of the main circuit board will show
the revision level of the software for 5 seconds, and then go to (-). While the tank is filling, the display will read
(FIL). When the tank is full the display will return to (-).
P3747
LEVEL 1 PROGRAMMING
LEFT
BUTTON
CENTER
BUTTON
RIGHT
BUTTON
TANK WATER TEMPERATURE & READY TEMPERATURE SET-UP
1. Press and hold the center button until P1 appears on the display (approximately 3
seconds) then release button. The tank water temperature set point will appear on
the display. Factory default is 200° F for most dispensers, and 90° F for some.
2. Press the (+) button to increase the temperature set point, and the (-) button to
decrease the set point.
3. After the Tank Temperature is entered, press and release the center button once
more. The display will read P2, then show the ready temperature set point. Factory
default is 195° F for most dispensers, and 85° F for some.
4. Use the (+) button to increase the temperature set point, and the (-) button to decrease the set point.
5. To exit Level 1 Program press and release the center button once more. The display
will show Software version, then (-).
LEVEL 2 PROGRAMMING
DISPENSE TEMPERATURE LOCKOUT, FAHRENHEIT OR CENTIGRADE SELECTION, &
FACTORY DEFAULTS
1. To enter Level 2 Programming, press and hold the center button until H1 appears
on the display (approximately 6 seconds) then release button. The display will either
read noL (LOCKOUT DISABLED) or Loc (LOCKOUT ENABLED). When (ENABLED),
unit will not dispense if the Tank Temperature is below the (READY) temperature
setting.
2. Use the (+) or (-) buttons to alternate between Loc and noL.
8
39338 012609
3. Press and release the center button once more. The display will read H2, then show
either FAH (Degrees in Fahrenheit) or Cen (Degrees in Centigrade).
4. Press and release the (+) or (-) buttons to alternate between FAH and CEn.
5. To Exit Level 2 Programming, press and release the Center Button twice more. The
Display will show the Software Version, then (-).
RESTORING FACTORY DEFAULTS
1. To restore Factory Defaults (This clears all settings that were previously entered),
press and release the center button until H1 appears on the display (approximately
6 seconds). Release the Center Button, then press and release the Center Button
twice more. The display will read H3, then show (- - -).
2. Press and hold both (+) and (-) buttons to initiate the resetting of the factory default settings. The display (- - -) will flash on and off during this time (about 5 to 7
seconds).
3. When the factory default numbers are loaded in, the display will stop flashing, then
read don (DONE). You can now release the two buttons.
NOTE: If you release the two buttons at any time before the display reads don, the Factory
Default numbers will not be entered. The old numbers will remain in the memory.
4. To exit Level 2 Program press and release the center button once more. The Display
will show the Software Version, then (-).
ADJUSTING DISPENSE VOLUMES
NOTE: The dispenser should be at operating temperature before setting dispense volumes.
1. Press and hold the hidden programming button, located under the ® next to the BUNN logo on the front of
the dispenser until the 3 LED's begin flashing from the left to the right. Release the button.
2. Place an empty graduated container under the dispense nozzle.
3. Press and release the batch size to be set. The LED's will stop flashing, and the LED over the button just
pressed will come on solid. Water will begin to dispense into the container.
4. When the desired amount of water is dispensed, press and release the same button. The water will stop
dispensing and the batch size is now set.
5. The LED's will begin flashing from left to right again. Repeat steps 2 thru 4 to set up the other batch sizes.
6. To exit the programming set up at any time, press and release the hidden button once. The dispenser is now
ready for use.
9
39338 012609
WIRING DIAGRAMS
SCHEMATIC WIRING DIAGRAM
H5E-DV PC
GRN
L1 N L2
RED-14
BLK-14
WHT-18
WHT-14
MASTER ON/OFF
SWITCH
RED-14
BLK-18
SELECTOR
SWITCH
LIMIT
THERMOSTAT
BLK-14
BLK-14
BLU-14
TANK HEATER
BRN-14
4000 W
WHI/VIO-14
TANK HEATER
WHT-14
1800 W
N.C.
DISPENSE
OVERFLOW
PROTECTION SWITCH
N.O.
COM
J5-1
J5-3
J7-1
J7-4
J2-1
J2-5
CONTROL
J3-1
BOARD
REFILL
WHT-18
SOL
BLK-18
VIO-18
WHI-18
WHI/BLU-18
J4-1
BLK
WHI
J6-1
PINK-22
GRN-18
MAIN
J2-10
WHT-18
SOL
WATER LEVEL
PROBE
t°
TANK
CONTROL PANEL ASSY
J1-1
Touch Switch Assembly Codes
STATIC
SHIELD
L2
L3
J1-5
L1
A4
A1
A2
J3-5
A3
A1
A2
A3
A4
B1
Left Dispense
Middle Dispense
Right Dispense
Manual Dispense/Stop
"Hidden" Switch
L1
L2
L3
Heater LED
Ready LED
Power LED
B1
J3-8
39333.0000C
J1-11
120V AC 2 WIRE + GND
120/208V AC 3 WIRE + GND
120/240V AC 3 WIRE + GND
SINGLE PHASE
06/07 ©2006 BUNN-O-MATIC CORPORATION
10
39338 012609
WIRING DIAGRAMS
L1
SCHEMATIC WIRING DIAGRAM
H5EA PC CE
L2
RED-14
BLK-14
GRN/YEL
EMI
FILTER
RED-14
BLK-18
LIMIT
THERMOSTAT
BLK-14
BLK-14
J7-1
J7-4
J4-1
J6-1
MAIN
CONTROL
J3-8
BOARD
RED-18
SOL
J2-10
J2-1
RED-14
DISPENSE
BLU-14
N.O.
J5-1
J2-5
BLU-14
4000 W
COM
OVERFLOW
PROTECTION SWITCH
J5-3
TANK HEATER
BLK
BLK-14
BLK
N.C.
BLU-14
LIMIT
THERMOSTAT
REFILL
RED-18
SOL
BLK-18
VIO-18
WHI-18
WHI/BLU-18
BLK
WHI
WATER
LEVEL
PROBE
PINK-22
GRN-18
TANK
t°
CONTROL PANEL ASSY
J1-1
Touch Switch Assembly Codes
STATIC
SHIELD
L2
L3
J1-5
L1
A4
A1
J3-5
A2
A3
A1
A2
A3
A4
B1
Left Dispense
Middle Dispense
Right Dispense
Manual Dispense/Stop
"Hidden" Switch
L1
L2
L3
Heater LED
Ready LED
Power LED
B1
J3-1
39333.0001A
J1-11
230V AC 2 WIRE + GND
SINGLE PHASE
03/09 ©2009 BUNN-O-MATIC CORPORATION
11
39338 040309
Download PDF