Belkin | SURF N300 F7D6301 | Technical data | Belkin SURF N300 F7D6301 Technical data

Communication and Monitoring
8 Communication and Monitoring
8.1
Communication Interface
Standard configuration:
1. Ethernet: Transmit the inverter working state such as output voltage, current, frequency, fault
information to the PC machine or other monitoring system. Ethernet can achieve multi-inverter wired
network at the same time.
Optional configuration:
WIFI: Wireless connect to route. Transmit the inverter working state such as output voltage, current,
frequency, fault information to the PC machine or other monitoring system. WIFI can achieve
multi-inverter wireless network at the same time.
RS485: Achieve multi-inverter network to monitor the inverter working state such as output voltage,
current, frequency, fault information
GPRS: Inform message by message.
Only choose one optional configuration when inverter is working.
8.2
Communication mode
When user want to know the information of the power system and monitor power system. We offer
following communications.
8.2.1 Ethernet communication
You can connect inverter to Internet by router (the router is not special for inverters, you can get any
brand in the market). Then you can see the inverter’s data in any place of the world.
WAN
Router
Figure 22 Ethernet communication
Hardware Requirements: computer which support windows(including xp,vista,win7), router, netting
twine, inverter(LAN mode).
Monitor mode: LAN and WAN.
LAN: Install SolarPower Browser in PC which can monitor inverters .In this mode, you can use a router
or nonuse.
If you use a router, you can monitor 254 inverters.
27
Communication and Monitoring
Parameter setting when using router:
Step 1˖Enter home interface automatically after startup (If not the home interface, press “ESC” return
to the home interface).
2012-03-03 10 : 00 : 00
Home
Power
kwh
0.0 W
Today
Total
t
208.4 V
205.9 V
0.0 KWh
0.0 KWh
1.045 kw
=
~
49.99 Hz
Press Esc to Main Menu
Step 2: Press “ESC” in home interface then enter the main menu.
2012-03-03 10 : 01 : 00
Main Menu
Instantaneous values
History
Event List
Settings
System Info
Press Esc to Home
Step 3: Move the cursor to "settings" and then press “OK”, will enter settings interface.
Settings
2012-03-03 10 : 02 : 25
Language
Input config
Date/Time
Reset Password
Clear date
Network
Clear events
AutoTest(Italy)
LCD contrast
Factory set
Country
Safety param
Press Esc to Main Menu
28
Communication and Monitoring
Step 4: Move the cursor to "network", press "OK" and then enter "Input Password" interface.
2012-03-03 10 : 03 : 10
Input Password
Please input customer password
0
Left/Right : Move Selection
Up/Down : Increase/Decrease value
Press Esc to Settings
Step 5: Press "right" or "left" key to move the cursor to select the figure which need to be modified.
Press "up" or "down" key to modify figure. If the password is correct will enter 'Ethernet" interface.
Ethernet
2012-03-03 10 : 16 : 23
Auto-IP/DHCP
Manual-IP
Current mode: Auto-IP/DHCP
Press OK to confirm
Step 6: Move the cursor to "Auto-IP/DHCP", press "OK" twice. LCD interface will Reboot and then
enter into home interface automatically.
Ethernet
2012-03-03 10 : 16 : 40
Auto-IP/DHCP
Manual-IP
Current mode: Auto-IP/DHCP
Confirm?
If you don’t use a router, you can only monitor 1 inverter. Need to use cable to connect inverter with PC.
Parameter setting when not using router:
Refer to settings when using router:Main Menu->Settings->Network->Ethernet. In "Ethernet" interface
move the cursor to "Manual-IP", press "OK" twice(one press to confirm).
29
Communication and Monitoring
Ethernet
2012-03-03 10 : 22 : 23
Auto-IP/DHCP
Manud-IP
Current mode: Manual-IP
Press OK to confirm
Ethernet
2012-03-03 10 : 22 : 50
Auto-IP/DHCP
Manud-IP
Current mode: Manual-IP
Confirm?
Press "OK" twice then will enter "Manual-IP" interface. Press "right" or "left" key to move the cursor
to select the figure which need to be modified. Press "up" or "down" key to modify figure(IP Address˖
192.168.000.002. Subnet Mask˖255.255.255.000, others are 0). Press “OK” after modifying. LCD will
display the setting parameter and press “OK” again, now setting is over. LCD interface will Reboot and
then enter to home interface automatically.
Manual-IP
2012-03-03 10 : 26 : 05
IP:
192.168.000.002
SubnetMask:
255.255.255.000
Gateway:
000.000.000.000
DNS:
000.000.000.000
Left/Right : Move Selection
Up/Down : Increase/Decrease value
Press OK to confirm
Parameter set for PC:
Set IP address as 192.168.000.001,
Set Subnet mask as 255.255.255.000.
ķ Need to install SolarRiver-D inverter monitoring software in the PC when using
WIFI, Ethernet communication.
ĸ Can’t using RS485 and Ethernet communication mode for a PC at the same time.
Ĺ The default set is “Auto IP”. If use router, LAN or WAN monitor is available without
any parameter setting.
ĺ In WAN mode, must use router and recommend to select auto IP mode.
30
Communication and Monitoring
8.2.2 RS485 Communication
RS485 is generally for at most 32 inverters communication at the same time. But the length of
communication wire should be”1200m. You can read and analyse data by PC if the system is equipped
with Solar-Log200/500/1000. Please refer to Solar-Log200/500/1000 manual for more information.
Figure 23 RS-485 jack
Two types of cable must be prepared before using Solar-Log to monitor mult-inverters.
The communication cable between inverter and inverter:
1. Prepare two 8-PIN RJ45 modular plug, hold the RJ45 modular plug with the 'clip' on the bottom,
the 'opening' (where you insert the cable) facing you, the order number is 1 to 8 from left to right,
as figure 24.
T-568B
Pin 1
1 2 3 4 5 6 7 8
RJ-45 Plug
O/ O G/ B B/ G Br/ Br
Figure 24
2. Use a length of communication cable, then push the 8 color wires into the modular plug follow the
same order as below.
1
orange white
2
orange
3
green white
4
blue
5
blue white
6
green
7
brown white
8
brown
3. Then put the both ends of communication cable into the communication ports of inverter respectively.
If there are N inverters, need N-1 this communication cable.
31
Communication and Monitoring
The communication cable between inverter and Solar-Log:
1. One side of cable is the same as cable between inverter and inverter, the other side remains 4 colour
wires: green white, green, orange white, orange, as shown in figure 25.
Figure 25
2.
Connect 4 colour wires to 1,4,5,6 port of Solar-Log.
1
green white
2
reserve
3
reserve
4
green
5
orange white
6
orange
8.2.3 WIFI communication
You can connect inverter to Internet by router. Then you can see the inverter’s data in any place where
internet is available.
WAN
Router
Figure 26 WIFI communication
OS: win xp, Vista, Win7;
Network: Lan or Wan;
Wifi: 802.11g.
32
Communication and Monitoring
WIFI settings:
Note˖Appendix is WIFI route list.
Step1: Connect a cable following the steps of Ethernet before opening "SolarPower Browser".
Step2: Double-click name of inverter to enter detail information page. Set the SSID of router which
WIFI is going to be connected to and input the password(known from installation contractor) then save
these information.
Step3˖Reboot the computer automatically and disconnect netting twine connection.
Step4˖Check WIFI information:
Enter the interface successively: Main Menu->Settings->Network, move the cursor to "WIFI" and press
"OK".
2012-03-03 10 : 27 : 23
Network
Ethernet
WIFI
Press OK to confirm
33
Communication and Monitoring
The GUI bellow tells the WIFI hasn’t been set yet.
2012-03-03 10 : 28 : 10
Wifi
Link Name:
Press ESC to Back
If WIFI has been set, shown as following figure.
2012-03-03 10 : 28 : 50
Wifi
Link Name:
BAFFAL0-5D8959
Press ESC to Back
Hardware Requirements: routerǃinverter equipped with WIFIǃPC˄with
SolarPower Browser software˅
8.2.4 GPRS communication
GPRS function is that sends fault message to user when inverter is at fault.
Hardware Requirements: SIM card, inverter equipped with GPRS, mobile telephone.
Monitor mode: message.
GPRS settings:
Step1: Use mobile telephone to set PIN code of SIM card which will be installed in inverter.
Step2: Connect cable following the steps of Ethernet before opening "SolarPower Browser".
34
Communication and Monitoring
Step3: Double-click name of inverter then enter detail information interface. Set the PIN code, service
center number and customer mobile telephone number then save these information.
Step4: Reboot the computer automatically.
Step5: Check GPRS information:
Enter the interface successively: Main Menu->Settings->Network, move the cursor to "GPRS" and
press "OK".
2012-03-03 10 : 27 : 23
Network
Ethernet
GPRS
Press OK to confirm
If GPRS setting has not been initialised, shown as following figure.
2012-03-03 10 : 29 : 10
GPRS Message
No settings
Press ESC to Back
35
Communication and Monitoring & Troubleshooting and maintenance
If GPRS setting has been initialised, press "OK" to check the information, shown as following figure.
GPRS Message
2012-03-03 10 : 32 : 06
PIN
1234
Center Number:
+8613800510500
Customer Number:
+8615000000000
Press OK to have a test!
Press ESC to Back
9
Troubleshooting and maintenance
9.1 Troubleshooting
This section illustrates possible faults of an inverter and solving methods and provides users with
troubleshooting tips to help them identify and solve common problems. Please read the following
troubleshooting steps:
1. Check the warning, fault messages or fault codes displayed on LCD. If a message is displayed, record
it before doing anything further.
2. Attempt the solution according to table 5.
3. If no fault message is displayed on LCD, check the following list whether the installation meet the
requirements.
—
—
—
—
—
Is the inverter installed in a clean, dry, adequately ventilated place?
Have the DC input switch been opened?
Do section area and length of cable meet requirements?
Are the input and output connections and wiring in good condition?
Are the configuration settings correct for user particular installation?
Steps of checking the warning and fault information displayed on LCD:
Move the cursor to the "Event list" and then press “OK” in main menu interface, then enter "Event list"
interface.
Events list
Code
40
10
09
08
08
2012-03-03 10 : 42 : 07
Message
Bus over voltage
2012-03-03 10 : 40 : 36
PV2 over voltage
2012-03-03 10 : 40 : 34
PV1 over voltage
2012-03-03 10 : 40 : 34
No utility
2012-03-03 10 : 40 : 22
No utility
2012-03-03 10 : 40 : 14
01/20
Press ESC to Main Menu
Figure 27 Event list interface
36
Troubleshooting and maintenance
When SolarRiver-D inverter is at fault, the fault information is composed of code, occurring time and
fault description.
Please contact Samil Power Co.,Ltd for further technical assistance. Please provide detailed installation
information and inverter model, serial number and fault information.
Table 5 Troubleshooting list
Faults
Grid volt / freq over /
underrating
Diagnosis and Solutions
-Wait grid go back to normal working state.
-Mak sure that grid voltage and frequency complies with standards.
-Or, please ask for help
No Utility
-Check grid-connection
-Or, please ask for help.
PV1/PV2 over voltage
-Check the PV open-circuit voltage whether it is >Max.DC voltage.
-Or, please ask for help.
DCI out range
- Wait for one minute.
-Or, please ask for help.
SCI/ SPI communication
fault
-Disconnect DC and AC side, and connect them again.
-Or, please ask for help.
PV1/PV2 isolation fault
-Check the impedance among PV (+) PV (-) and grounding whether
they are>600Kohm.
-Or, please ask for help.
Consistent Fault
-Disconnect DC and AC side, and connect them again.
-Or, please ask for help.
Relay Failure
-Disconnect DC and AC side, and connect them again.
-Or, please ask for help.
GFCI over 30mA /60mA /
150mA /300mA fault
-Check whether leakage current is too high.
-Disconnect DC and AC side, check the surrounding equipment on the
AC side.
-Reconnect the input side and check inverter after troubleshooting.
-Or, please ask for help.
EEPROM read/ write failure
-Disconnect DC and AC side, and connect them again.
-Or, please ask for help.
Bus over voltage
-Disconnect DC side, and connect them again.
-Check L line and N line whether it has connection faults.
-Or, please ask for help.
GFCI device failure
-Disconnect DC and AC side, and connect them again.
-Or, please ask for help.
Input/ output current high
-Disconnect DC and AC side, and connect them again.
-Or, please ask for help.
37
Troubleshooting and maintenance & Decommissioning
9.2
Daily maintenance
Inverters generally do not need any maintenance or calibration, but ensure air-cooling fin not be covered
by any dust or dirties.
Inverter cleaning
Please use electric drier, soft dry cloth or brush to clean inverters. Water, corrosive chemical substance
or intense cleaning agent are not allowed to clean the inverter.
Cooling fin cleaning
To ensure inverter good performance and long-period usage, cooling fin needs to be left with adequate
space. Please use electric drier, soft cloth or brush to clean cooling fin. Water, corrosive chemical
substance or intense cleaning agent is not allowed.
10 Decommissioning
10.1 Decommissioning steps
1. Switch off the AC grid;
2. Switch Off the DC switch;
3. Wait 5 minutes;
4. Release the DC connectors;
5. Release the AC connectors.
Now inverters can be demounted safely.
10.2 Package
Please pack the inverter with the original package as far as possible. If original package is not available,
use an equivalent carton that meets the following requirements:
1. Load more than 50 kg;
2. With handle;
3. Can be fully sealed off.
10.3 Storage
Store the inverter in dry place where temperatures are between -25 °C - +70 °C.
10.4 Disposal
Please deliver inverters and packing materials to a suitable space where should meet disposal regulations
for electronic scrap at the end of its service.
38
Technical Data
11 Technical Data
11.1 Input (DC)
Model
Max.PV power[W]
SolarRiver
3400TL-D
SolarRiver
4000TL-D
SolarRiver
4500TL-D
SolarRiver
5000TL-D
SolarRiver
5200TL-D
3400
4000
4500
5000
5200
15/15
15/15
Max.DC voltage[V]
Max.input current[A]
550
10.5/10.5
12/12
13.5/13.5
Number of MPP trackers
/strings per MPP tracker
Max power of Track1/
Track2[W]
MPP voltage range
(at rated power)[V]
2/1
2200/2200
2500/2500
2750/2750
3000/3000
3100/3100
160~500
165~500
165~500
175~500
175~500
DC Switch
optional
Shutdown voltge/Start
voltage[V]
60/100
11.2 Output (AC)
SolarRiver
3400TL-D
SolarRiver
4000TL-D
SolarRiver
4500TL-D
SolarRiver
5000TL-D
SolarRiver
5200TL-D
AC nominal power[W]
3000
3680
4000
4600
4600
Max.AC power[W]
3200
3680
4300
4600
5000
Max.AC current[A]
16
16
22
23
24
SolarRiver
5000TL-D
SolarRiver
5200TL-D
Model
Nominal AC voltage/
range[V]
230/180~270
AC grid frequency/
range[Hz]
50/47~52
Power factor(cosij)
0.8lagging~0.8leading
Total harmonic distortion
(THDi)(at nominal power)
<3%
11.3 Efficiency
Model
SolarRiver
3400TL-D
SolarRiver
4000TL-D
SolarRiver
4500TL-D
Max.efficiency
97.4%
97.6%
97.6%
Euro efficiency
96.5%
97.1%
97.1%
MPPT efficiency
97.6%
97.6%
97.1%
97.1%
99.9%
39
Technical Data & Guarantees
11.4 General data
Model
Dimensions(W/H/D) [mm]
Weight [kg]
Operating temperature
range [°C]
Ingress protection
Topology
Internal consumption
(night) [W ]
Cooling concept
Noise (typical) [dB]
LCD display
Communication
Standard warranty [year]
SolarRiver
3400TL-D
SolarRiver
4000TL-D
SolarRiver
4500TL-D
SolarRiver
5000TL-D
SolarRiver
5200TL-D
520 / 380/ 175
26
-20~+60
IP65
tansformerless
<3
Convection
<30
3.5inch TFT LCD
Ethernet optional for RS485/GPRS/WiFi
5
12 Guarantees
Samil Power Co., Ltd offers 5 years warranty service for SolarRiver-D inverter. Warranty period is from
the date of installation. But the longest period don’t exceed 66 months from the date of delivering goods.
During the warranty period, Samil Power Co., Ltd guarantees normal function of the SolarRiver-D
inverter. If there are faults within our responsibility, we will provide maintenance free of charge.
During the warranty period, if inverter appears malfunction or fault, please contact your dealer or
installation contractor.
฀
฀
฀
฀
฀
฀
฀
฀
฀
40
The followings are not included in the scope of warranty:
¥ Use SolarRiver-D inverter for other purpose;
¥ Install incorrectly or not conform to the rule;
¥ Improper operation
¥ Useunqualified protection when working;
¥ Modify the equipment without authority;
¥ Damage because of external factors or the majeure force(such as lightning, over-voltage, bad weather,
and fire, earthquake, tsunami and so on);
¥ Poor ventilation;
¥ Don’t comply with the relevant safety regulations;
¥ Transportation damage.
Guarantees
Appendix
Apple
Corega
Belkin
Buffalo
Cisco
Linksys
AirPort Express with 802.11n
A1264
AirPort Extreme Simultaneous dual-band 802.11n
A1301
AirPort Extreme Simultaneous dual-band 802.11n (Late 2009)
A1354
Apple
A1143
CG-WLR300NNH
CG-WLR300NNH
CG-WLR300NM
CG-WLR300NM
IEEE802.11b/g/n Wireless Broadband AP/Router
CG-WLR300GNE
N Wireless Router
F5D8236-4 v2
N+ Wireless Router
F5D8235-4 v2
Enhanced Wireless Router
F6D4230-4 v2
Belkin N Wireless Router
F5D8236-4 v3000
N+ Wireless Router
F5D8235-4 v3
N Wireless Modem Router
F5D8636-4 v2
Belkin Router
F7D3302 v1
Belkin Router
F7D4302 v1
Belkin Router
F7D4301 v1
Belkin Wireless Modem Router
F7D1401 v1
Belkin Wireless Modem Router
F7D2401 v1,
F7D2401-B v1
Belkin Modem Router
F7D3402 v1
Surf Wireless Router
F7D2301
Share Max Wireless Router
F7D3301
Surf N300 Wireless N Router
F7D2301 V3000
Surf N300 Wireless N Router
F7D6301 V3000
Connect N150 Wireless Router
F7D5301 V3000
Connect N150 Wireless Router
F7D1301 V3000
BUFFALO Nfiniti Router WHR-HP-G300N
WHR-HP-G300N
BUFFALO AirStation WHR-HP-GN
WHR-HP-GN
BUFFALO Nfiniti Router WHR-G301N
WHR-G301N
BUFFALO Nfiniti Accesspoint WLAE-AG300N
WLAE-AG300N
BUFFALO Nfiniti Router WZR-HP-AG300H
WZR-HP-AG300H
BUFFALO Nfiniti Router WZR-HP-G302H
WZR-HP-G302H
BUFFALO-WZR-AMPG144NH
WZR-AMPG144NH
Wireless-N Gigabit Router
WRT310Nv2
Wireless-N Home Router
WRT120N
Wireless-N Access Point with Dual-Band
WAP610N
Dual-Band Wireless-N Gigabit Router
E2000
41
Guarantees
Wireless-N Broadband Router
E1000
Wireless-N Broadband Router
M10
Wireless-N Gigabit Router
M20
Wireless-N Broadband Router
E1000(v2.1)
Wireless-N Gigabit Router
M20
Dual-Band Wireless-N Gigabit Router
E2000
Wireless-N Broadband Router
E1000(v2)
Wireless-N Broadband Router
M10(v2)
Linksys
WRT54G v8
Cisco AIR-AP1231G-A-K9
AIR-AP1231G-A-K9
Linksys WRT54
WRT54 G2 v1
Cisco Aironet
Aironet 1200
Cisco Controller AP
1130G
Cisco Controller
1242AG
IEEE 802.11 b/g/N Wireless Router / DIR-605
DIR-605
D-Link DIR-615 Wireless N Router
DIR-615E3/E4
IEEE 802.11 b/g/N Wireless Router /DIR-605.B2
DIR-605.B2
WIRELESS N 150 HOME ROUTER / DIR-600 V.B4
DIR-600 V.B4
DIR-815 Wireless N Dual Band Router / DIR-815 v1.00
DIR-815 v1.00
Wireless N 8 port router
DIR-632
IEEE 802.11 Wireless N 150 Home Router / DIR-501
DIR-501
IEEE 802.11 Wireless N Router / DIR-515
DIR-515
IEEE 802.11a/b/g/n wireless Access Point / DAP-2690
DAP-2690
IEEE 802.11 b/g Mobile Wireless Router / DIR-412
DIR-412
Dlink G730AP v2
G730AP v2
IO Data
I-O DATA WN-G54/DCR
WN-G54/DCR
Motorola
Symbol AP-5131
AP5131
Aterm WR4100N
WR4100N
NEC PA-WR8170N-HP
PA-WR8170N-HP
NEC PA-WR8700N-HP
PA-WR8700N-HP
Wireless-N 300 Router
JWNR2000
Wireless-N 150 Router
WNR1000v2
Wireless-N 300 Router
WNR2000v2
Wireless-N 150 Router
WNR612v2
N150 Wireless Router
WNR1000v3
N150 Wireless Router
WGR614v10
Powerline AV 200 Wireless-N Extender XAVN2001
XAVN2001
N300 Wireless Router with USB
WNR2200
D-Link
NEC
Netgear
42
Guarantees
ProSafe Dual Band Wireless-N Access Point
WNDAP350
ProSafe Wireless-N Access Point
WNAP320
WGR614 v9
WGR614 v9
Orinoco AP-700
Orinoco AP-700
Proxim ORiNOCO
AP-600
150Mbps Wireless Lite N Router
TL-WR740N
150Mbps Wireless Lite-N Router
TL-WR741ND
300Mbps Wireless N Router
TL-WR841N
TP-LINK Wireless N Access Point
TL-WA901ND
TP-LINK 300Mbps Wireless N Access Point
TL-WA801ND
Planex-MZK-MF300N
MZK-MF300N
Proxim
TP-Link
Planex
43
SAMIL POWER CO., LTD.
Marketing & Sales Office
Factory
Add:
No.52,Huigu Innovation Park, Huishan District,
Wuxi,Jiangsu Province,P.R.China 214174
Add:
Tel:
+86 510 83593131
Fax:
+86 510 81819678
E-mail:service@samilpower.com
http://www.samilpower.com
No.66 Taihangshan Road,
Suyu Economic Development Zone, Suqian City,
Jiangsu Province, P.R.China
Tel:
+86 527 88754666
Fax:
+86 527 84453877
223800
Download PDF