Brother | HL-4140CN | User`s guide | Brother HL-4140CN User`s guide

Multi-Protocol On-board Ethernet Print Server and Wireless
Ethernet Print Server
NETWORK
USER’S GUIDE
This Network User's Guide provides useful information of wired
and wireless network settings and security settings using your
Brother machine. You can also find supported protocol
information and detailed troubleshooting tips.
To find basic information about network and advanced network
features of your Brother machine, see the Network Glossary.
To download the latest manual, please visit the Brother Solutions
Center at (http://solutions.brother.com/). You can also download
the latest drivers and utilities for your machine, read FAQs and
troubleshooting tips or learn about special printing solutions from
the Brother Solutions Center.
Version 0
ENG
Definitions of notes
We use the following icons throughout this User’s Guide:
IMPORTANT
IMPORTANT indicates a potentially hazardous situation which, if not avoided,
may result in damage to property or loss of product function.
Note
Notes tell you how you should respond to a situation that may arise or give tips
about how the operation works with other features.
IMPORTANT NOTE
 This product is approved for use in the country of purchase only. Do not use this product outside the
country of purchase as it may violate the wireless telecommunication and power regulations of that
country.
 Windows® XP in this document represents Windows ® XP Professional, Windows® XP Professional x64
Edition and Windows® XP Home Edition.
 Windows Server® 2003 in this document represents Windows Server® 2003 and Windows Server® 2003
x64 Edition.
 Windows Server® 2008 in this document represents Windows Server® 2008 and Windows Server® 2008
R2.
 Windows Vista® in this document represents all editions of Windows Vista®.
 Windows® 7 in this document represents all editions of Windows® 7.
 Please go to the Brother Solutions Center at http://solutions.brother.com/ and click Manuals on your
model page to download the other manuals.
 Not all models are available in all countries.
i
Table of Contents
1
Introduction
1
Network features........................................................................................................................................1
Other Network features .......................................................................................................................2
2
Changing your machine’s network settings
3
How to change your machine’s network settings
(IP address, Subnet mask and Gateway) ...............................................................................................3
Using the control panel........................................................................................................................3
Using the BRAdmin Light utility ...........................................................................................................3
Other Management Utilities .......................................................................................................................6
Web Based Management (web browser) ............................................................................................6
BRAdmin Professional 3 utility (Windows®) ........................................................................................6
Web BRAdmin (Windows®) .................................................................................................................7
BRPrint Auditor (Windows®)................................................................................................................7
3
Configuring your machine for a wireless network (For HL-4570CDW(T))
8
Overview....................................................................................................................................................8
Step by step chart for wireless network configuration ..............................................................................9
For Infrastructure mode .......................................................................................................................9
For Ad-hoc mode...............................................................................................................................10
Confirm your network environment..........................................................................................................11
Connected to a computer with a WLAN access point/router in the network (Infrastructure mode) ...11
Connected to a wireless capable computer without a WLAN access point/router in the network
(Ad-hoc mode)...............................................................................................................................11
Confirm your wireless network setup method..........................................................................................12
Configuration using WPS or AOSS™ from the control panel menu to configure your machine for
a wireless network (Automatic Wireless mode) (Infrastructure mode only) (Recommended).......12
Configuration using the machine’s control panel Setup Wizard to configure
your machine for a wireless network .............................................................................................12
Configuration using the Brother installer application on the CD-ROM to configure
your machine for a wireless network .............................................................................................13
Configuration using the PIN Method of Wi-Fi Protected Setup to configure
your machine for a wireless network (Infrastructure mode only) ...................................................15
Configuring your machine for a wireless network
(For Infrastructure mode and Ad-hoc mode) ........................................................................................16
Using WPS or AOSS™ from the control panel menu to configure
your machine for a wireless network (Automatic Wireless mode) .................................................16
Using the Setup Wizard from the control panel .................................................................................16
Configuring your machine when the SSID is not broadcast ..............................................................17
Configuring your machine for an enterprise wireless network...........................................................20
Using the Brother installer application on the CD-ROM to configure your machine for a wireless
network ..........................................................................................................................................23
Using the PIN Method of Wi-Fi Protected Setup ...............................................................................24
ii
4
Wireless configuration using the Brother installer application
(For HL-4570CDW(T))
26
Before configuring the wireless settings ..................................................................................................26
Configure the wireless settings................................................................................................................26
5
Control panel setup
31
Network menu..........................................................................................................................................31
TCP/IP ...............................................................................................................................................31
Ethernet (wired network only)............................................................................................................33
Status (For HL-4140CN and HL-4150CDN)/Wired Status (For HL-4570CDW(T))............................33
Setup Wizard (wireless network only) ...............................................................................................33
WPS or AOSS™ (wireless network only) ..........................................................................................33
WPS w/PIN Code (wireless network only).........................................................................................33
WLAN Status (wireless network only) ...............................................................................................33
MAC Address ....................................................................................................................................34
Set to Default (For HL-4570CDW(T)) ................................................................................................34
Wired Enable (For HL-4570CDW(T)) ................................................................................................34
WLAN Enable (For HL-4570CDW(T)) ...............................................................................................34
Reset the network settings to the factory default.....................................................................................35
Printing the Network Configuration List ...................................................................................................35
Printing the WLAN report (For HL-4570CDW(T)) ....................................................................................36
Function table and default factory settings ..............................................................................................37
HL-4140CN and HL-4150CDN ..........................................................................................................37
HL-4570CDW(T)................................................................................................................................38
6
Web Based Management
40
Overview..................................................................................................................................................40
How to configure the machine settings using Web Based Management (web browser).........................40
Secure Function Lock 2.0 ........................................................................................................................42
How to configure the Secure Function Lock 2.0 settings using Web Based Management
(web browser)................................................................................................................................42
Synchronize with SNTP server ................................................................................................................44
Store Print Log to Network.......................................................................................................................46
How to configure the Store Print Log to Network settings using Web Based Management
(web browser)................................................................................................................................46
Error Detection Setting ......................................................................................................................48
Understanding Error Messages.........................................................................................................49
Using Store Print Log to Network with Secure Function Lock 2.0 .....................................................50
iii
7
Security features
51
Overview..................................................................................................................................................51
Managing your network machine securely using SSL/TLS .....................................................................52
Secure Management using Web Based Management (web browser) ..............................................52
Printing documents securely using SSL/TLS...........................................................................................54
Sending or Receiving an E-mail securely ................................................................................................55
Configuration using Web Based Management (web browser) ..........................................................55
Sending an E-mail with user authentication ......................................................................................55
Sending or Receiving an E-mail securely using SSL/TLS.................................................................56
Using IEEE 802.1x authentication ...........................................................................................................57
IEEE 802.1x authentication configuration using Web Based Management (web browser)...............57
Secure Management using BRAdmin Professional 3 (Windows®)..........................................................59
To use the BRAdmin Professional 3 utility securely, you need to follow the points below ................59
Using Certificates for device security.......................................................................................................60
Configure certificate using Web Based Management .......................................................................61
Creating and installing a certificate....................................................................................................62
Import and export the certificate and private key...............................................................................68
Managing multiple certificates .................................................................................................................69
Import and export a CA certificate .....................................................................................................70
8
Troubleshooting
71
Overview..................................................................................................................................................71
Identifying your problem ....................................................................................................................71
A
Appendix A
77
Supported protocols and security features ..............................................................................................77
B
Index
78
iv
1
Introduction
1
1
Network features
1
Your Brother machine can be shared on a 10/100 MB wired or IEEE 802.11b/g wireless Ethernet network
using the internal network print server. The print server supports various functions and methods of connection
depending on the operating system you are running on a network supporting TCP/IP. The following chart
shows what network features and connections are supported by each operating system.
Note
Although the Brother machine can be used in both a wired and wireless network, only one connection
method can be used at a time.
Operating Systems
Windows Server®
2003/2008
Mac OS X 10.4.11 10.6.x
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
Windows®
2000/XP
Windows Vista®
Windows® 7
Printing
BRAdmin Light
See page 3.
BRAdmin Professional 3 1
See page 6.
Web BRAdmin 1
See page 7.
Web Based Management
(web browser)
See page 40.
Status Monitor
See User's Guide.
Driver Deployment Wizard
Vertical Pairing
See Network Glossary.
r2
1
BRAdmin Professional 3 and Web BRAdmin are available as a download from http://solutions.brother.com/.
2
Windows® 7 only.
1
Introduction
Other Network features
1
1
Security
1
Your Brother machine employs some of the latest network security and encryption protocols available. (See
Security features on page 51.)
Secure Function Lock 2.0
1
Secure Function Lock 2.0 increases security by restricting the use of functions. (See Secure Function
Lock 2.0 on page 42.)
Store Print Log to Network
1
The Store Print Log to Network feature allows you to save the print log file from your Brother machine to a
network server using CIFS. (See Store Print Log to Network on page 46.)
2
2
Changing your machine’s network
settings
2
How to change your machine’s network settings
(IP address, Subnet mask and Gateway)
2
Using the control panel
2
You can configure your machine for a network using the control panel Network menu. (See Control panel
setup on page 31.)
Using the BRAdmin Light utility
2
The BRAdmin Light utility is designed for initial setup of Brother network connected devices. It also can
search for Brother products in a TCP/IP environment, view the status and configure basic network settings,
such as IP address.
Installing BRAdmin Light
2
 Windows®
a
b
c
Please make sure that your machine is ON.
d
e
The CD-ROM main menu will appear. Click Install Other Drivers or Utilities.
Turn on your computer. Close any applications running before configuration.
Put the supplied CD-ROM into your CD-ROM drive. The opening screen will appear automatically. If
the model name screen appears, choose your machine. If the language screen appears, choose your
language.
Click BRAdmin Light and follow the on-screen instructions.
 Macintosh
The BRAdmin Light software will be installed automatically when you install the printer driver. If you have
already installed the printer driver, you do not have to install BRAdmin Light again.
3
2
Changing your machine’s network settings
Setting the IP address, Subnet Mask and Gateway using BRAdmin Light
2
Note
• You can download Brother's latest BRAdmin Light utility from http://solutions.brother.com/.
• If you require more advanced machine management, use the latest version of BRAdmin Professional 3
utility that is available as a download from http://solutions.brother.com/. This utility is only available for
Windows® users.
2
• If you are using a firewall function of anti-spyware or antivirus applications, temporarily disable them. Once
you are sure that you can print, re-enable the application.
• Node name: The Node name appears in the current BRAdmin Light window. The default node name of
the print server in the machine is “BRNxxxxxxxxxxxx” for a wired network or “BRWxxxxxxxxxxxx” for a
wireless network. (“xxxxxxxxxxxx” is your machine’s MAC Address / Ethernet Address.)
• The default password for Brother print servers is “access”.
a
Start the BRAdmin Light utility.
 Windows®
Click Start / All Programs 1 / Brother / BRAdmin Light / BRAdmin Light.
1
Programs for Windows® 2000 users
 Macintosh
Double-click Macintosh HD (Startup Disk) / Library / Printers / Brother / Utilities /
BRAdmin Light.jar file.
b
BRAdmin Light will search for new devices automatically.
4
Changing your machine’s network settings
c
Double-click the unconfigured device.
Windows®
Macintosh
2
Note
• If the print server is set to its factory default settings (if you do not use a DHCP/BOOTP/RARP server), the
device will appear as Unconfigured in the BRAdmin Light utility screen.
• You can find the Node Name and MAC Address (Ethernet Address) by printing the Network Configuration
List. (See Printing the Network Configuration List on page 35 for information on how to print the Network
Configuration List on your print server.) You can also find the MAC Address from the control panel. (See
Chapter 5: Control panel setup.)
d
Choose STATIC from Boot Method (BOOT Method). Enter the IP Address, Subnet Mask and
Gateway (if needed) of your print server.
Windows®
e
f
Macintosh
Click OK.
With the correctly programmed IP address, you will see the Brother print server in the device list.
5
Changing your machine’s network settings
Other Management Utilities
2
Your Brother machine has the following management utilities other than the BRAdmin Light utility. You can
change your network settings using these utilities.
2
Web Based Management (web browser)
2
A standard web browser can be used to change your print server settings using the HTTP (Hyper Text
Transfer Protocol). (See How to configure the machine settings using Web Based Management (web
browser) on page 40.)
BRAdmin Professional 3 utility (Windows®)
2
BRAdmin Professional 3 is a utility for more advanced management of network connected Brother devices.
This utility can search for Brother products on your network and view the device status from an easy to read
Explorer style window that changes color identifying the status of each device. You can configure network
and device settings along with the ability to update device firmware from a Windows® computer on your LAN.
BRAdmin Professional 3 can also log activity of Brother devices on your network and export the log data in
an HTML, CSV, TXT or SQL format.
For users who want to monitor locally connected machines, install the Print Auditor Client software on the
client PC. This utility allows you to monitor machines that are connected to a client PC via the USB or parallel
interface from BRAdmin Professional 3.
For more information and to download the software, visit us at http://solutions.brother.com/.
Note
• Please use the latest version of the BRAdmin Professional 3 utility that is available as a download from
http://solutions.brother.com/. This utility is only available for Windows® users.
• If you are using a firewall function of anti-spyware or antivirus applications, temporarily disable them. Once
you are sure that you can print, configure the software settings following the instructions.
• Node name: The Node name for each Brother device on the network appears in BRAdmin Professional 3.
The default Node name is “BRNxxxxxxxxxxxx” for a wired network or “BRWxxxxxxxxxxxx” for a wireless
network. (“xxxxxxxxxxxx” is your machine’s MAC Address / Ethernet Address.)
6
Changing your machine’s network settings
Web BRAdmin (Windows®)
2
Web BRAdmin is a utility for managing network connected Brother devices. This utility can search for Brother
products on your network, view the status and configure the network settings.
Unlike BRAdmin Professional 3, which is designed for Windows® only, Web BRAdmin is a server based utility
that can be accessed from any client PC with a web browser that supports JRE (Java Runtime Environment).
By installing the Web BRAdmin server utility on a computer running IIS 1, administrators can connect to the
Web BRAdmin server using a web browser, which then communicates with the device itself.
2
For more information and to download the software, visit us at http://solutions.brother.com/.
1
Internet Information Server 4.0 or Internet Information Services 5.0/5.1/6.0/7.0
BRPrint Auditor (Windows®)
2
The BRPrint Auditor software brings the monitoring power of Brother network management tools to locally
connected machines. This utility allows a client computer to collect usage and status information from a
Brother machine connected via the parallel or USB interface. The BRPrint Auditor can then pass this
information to another computer on the network running BRAdmin Professional 3 or Web BRAdmin 1.45 or
greater. This allows the administrator to check items such as page counts, toner and drum status and the
firmware version. In addition to reporting to Brother network management applications this utility can E-mail
the usage and status information directly to a predefined E-mail address in a CSV or XML file format (SMTP
Mail support required). The BRPrint Auditor utility also supports E-mail notification for reporting warning and
error conditions.
7
3
Configuring your machine for a wireless
network (For HL-4570CDW(T))
3
Overview
3
To connect your machine to your wireless network, we recommend you to follow the steps in the Quick Setup
Guide using WPS or AOSS™ from the control panel menu. By using this method, you can easily connect your
machine to your wireless network.
Please read this chapter for additional methods on how to configure the wireless network settings. For
information on TCP/IP settings, see How to change your machine’s network settings (IP address, Subnet
mask and Gateway) on page 3.
Note
• To achieve optimum results with normal everyday document printing, place the Brother machine as close
to the WLAN access point/router as possible with minimal obstructions. Large objects and walls between
the two devices as well as interference from other electronic devices can affect the data transfer speed of
your documents.
Due to these factors, wireless may not be the best method of connection for all types of documents and
applications. If you are printing large files, such as multi-page documents with mixed text and large
graphics, you may want to consider choosing wired Ethernet for a faster data transfer, or USB for the
fastest throughput speed.
• Although the Brother machine can be used in both a wired and wireless network, only one connection
method can be used at a time.
• Before configuring wireless settings, you will need to know your Network name: (SSID, ESSID) and
Network Key. If you are using an enterprise wireless network you also need to know the User ID and
Password.
8
3
Configuring your machine for a wireless network (For HL-4570CDW(T))
Step by step chart for wireless network configuration
For Infrastructure mode
a
3
Confirm your network environment. See page 11.
 Infrastructure mode
 Ad-hoc mode
Connected to a computer with a WLAN access
point/router
b
3
or
3
See page 10
Connected to a wireless capable computer
without a WLAN access point/router
Confirm your wireless network setup method. See page 12.
Using the
WPS/AOSS™
control panel menu
(Automatic Wireless
mode)
Using the Setup
Wizard 1 from the
control panel
Using the Brother
installer
application
Using the PIN
Method of Wi-Fi
Protected Setup
(Recommended)
Using WPS/AOSS™, a USB 1 or
network cable 1
c
Configure your machine for a wireless network. See page 16.
See the Quick Setup
Guide
See the Quick Setup
Guide
See page 26
See page 24
Installing the printer driver (See the Quick Setup Guide)
1
Supporting IEEE 802.1x
Wireless configuration and installing the printer driver have been completed.
9
Configuring your machine for a wireless network (For HL-4570CDW(T))
For Ad-hoc mode
a
3
Confirm your network environment. See page 11.
 Ad-hoc mode
 Infrastructure mode
Connected to a wireless capable computer
without a WLAN access point/router
b
or
Connected to a computer with a WLAN access
point/router
Confirm your wireless network setup method. See page 12.
Using the Setup Wizard from the control panel
(Recommended)
c
See page 9
Using the Brother installer
application
Configure your machine for a wireless network. See page 16.
See page 16
See page 26
Installing the printer driver (See the Quick Setup Guide)
Wireless configuration and installing the printer driver have been completed.
10
3
Configuring your machine for a wireless network (For HL-4570CDW(T))
Confirm your network environment
3
Connected to a computer with a WLAN access point/router in the network
(Infrastructure mode)
3
1
3
4
2
3
1 WLAN access point/Router 1
1
If your computer supports Intel® MWT (My WiFi Technology), you can use your computer as a Wi-Fi Protected Setup supported access point.
2 Wireless network machine (your machine)
3 Wireless capable computer connected to the WLAN access point/router
4 Wired computer which is not wireless capable connected to the WLAN access point/router with a
network cable
Connected to a wireless capable computer without a WLAN access point/router
in the network (Ad-hoc mode)
3
This type of network does not have a central WLAN access point/router. Each wireless client communicates
directly with each other. When the Brother wireless machine (your machine) is part of this network, it receives
all print jobs directly from the computer sending the print data.
1
2
1 Wireless network machine (your machine)
2 Wireless capable computer
Note
We do not guarantee the wireless network connection with Windows Server® products in Ad-hoc mode.
11
Configuring your machine for a wireless network (For HL-4570CDW(T))
Confirm your wireless network setup method
3
There are four methods to configure your wireless network machine. Use WPS/AOSS™ from the control
panel menu (recommended), Setup Wizard from the control panel, the Brother installer application on the
CD-ROM or the PIN Method of Wi-Fi Protected Setup. The setup process will be different depending on your
network environment.
Configuration using WPS or AOSS™ from the control panel menu to configure
your machine for a wireless network (Automatic Wireless mode)
(Infrastructure mode only) (Recommended)
3
3
We recommend that you use WPS or AOSS™ from the control panel menu to configure your wireless
network settings if your WLAN access point/router (A) supports either Wi-Fi Protected Setup (PBC 1) or
AOSS™.
A
1
Push Button Configuration
Configuration using the machine’s control panel Setup Wizard to configure
your machine for a wireless network
3
You can use the machine’s control panel to configure your wireless network settings. By using the control
panel Setup Wizard function, you can easily connect your Brother machine to your wireless network. You
must know your wireless network settings before you proceed with this installation.
12
Configuring your machine for a wireless network (For HL-4570CDW(T))
Configuration using the Brother installer application on the CD-ROM to
configure your machine for a wireless network
3
You can also use the Brother installer application on the CD-ROM we have provided with the machine. You
will be guided by the on-screen instructions until you are able to use your Brother wireless network machine.
You must know your wireless network settings before you proceed with this installation.
Configuration using the Automatic Wireless mode
3
If your WLAN access point/router (A) supports either Wi-Fi Protected Setup (PBC 1) or AOSS™, you can
configure the machine easily without knowing your wireless network settings using the Brother installer
application.
A
1
Push Button Configuration
13
3
Configuring your machine for a wireless network (For HL-4570CDW(T))
Configuration temporarily using a USB or network cable
3
You can temporarily use a USB cable or network cable when you configure your Brother machine in this
method.
 You can remotely configure the machine from a computer that is also on the network using a USB cable
(A) 1.
3
A
1
You can configure the wireless settings of the machine using a USB cable temporarily connected to a wired or wireless computer.
 If there is an Ethernet Hub or Router on the same network as the WLAN access point (A), you can
temporarily connect the Hub or Router to the machine using a network cable (B). You can then remotely
configure the machine from a computer on the network.
A
B
14
Configuring your machine for a wireless network (For HL-4570CDW(T))
Configuration using the PIN Method of Wi-Fi Protected Setup to configure your
machine for a wireless network (Infrastructure mode only)
3
If your WLAN access point/router (A) supports Wi-Fi Protected Setup, you can also configure using the
PIN Method of Wi-Fi Protected Setup.
 Connection when the WLAN access point/router (A) doubles as a Registrar 1.
3
A
 Connection when another device (C), such as a computer is used as a Registrar 1.
A
C
1
The Registrar is a device that manages the wireless LAN.
15
Configuring your machine for a wireless network (For HL-4570CDW(T))
Configuring your machine for a wireless network
(For Infrastructure mode and Ad-hoc mode)
3
IMPORTANT
• If you are going to connect your Brother machine to your network, we recommend that you contact your
system administrator prior to installation. You must know your wireless network settings before you
proceed with this installation.
3
• If you have previously configured the wireless settings of the machine, you must reset the network LAN
settings before you can configure the wireless settings again. Press + or - to choose Network,
Network Reset, Reset and then choose Yes to accept the change. The machine will restart
automatically.
Using WPS or AOSS™ from the control panel menu to configure your machine
for a wireless network (Automatic Wireless mode)
3
If your WLAN access point/router supports either Wi-Fi Protected Setup (PBC 1) or AOSS™, you can
configure the machine easily without knowing your wireless network settings. Your Brother machine has the
WPS/AOSS™ menu on the control panel. See the Quick Setup Guide for more information.
1
Push Button Configuration
Using the Setup Wizard from the control panel
3
You can configure your Brother machine by using the Setup Wizard function. This is located in the
Network menu on the machine’s control panel.
 If you are configuring your machine for a smaller wireless network, such as your home environment:
• To configure your machine for an existing wireless network using the SSID and Network Key (if
required), see the Quick Setup Guide.
• If your WLAN access point/router is set to not broadcast the SSID name, see Configuring your machine
when the SSID is not broadcast on page 17.
 If you are configuring your machine for an IEEE 802.1x supported wireless network, see Configuring your
machine for an enterprise wireless network on page 20.
 If you are configuring your machine using Wi-Fi Protected Setup (PIN Method), see Using the PIN Method
of Wi-Fi Protected Setup on page 24.
16
Configuring your machine for a wireless network (For HL-4570CDW(T))
Configuring your machine when the SSID is not broadcast
a
3
Before configuring your machine we recommend you write down your wireless network settings. You will
need this information before you continue with the configuration.
Check and record the current wireless network settings.
Network name: (SSID, ESSID)
3
Communication Mode
Authentication method
Encryption mode
Network key
Infrastructure
Open system
NONE
—
WEP
Shared key
WEP
WPA/WPA2-PSK
AES
TKIP 1
Ad-hoc
Open system
NONE
—
WEP
1
TKIP is supported for WPA-PSK only.
For example:
3
Network name: (SSID, ESSID)
HELLO
Communication Mode
Authentication method
Encryption mode
Network key
Infrastructure
WPA2-PSK
AES
12345678
Note
If your router uses WEP encryption, enter the key used as the first WEP key. Your Brother machine
supports the use of the first WEP key only.
17
Configuring your machine for a wireless network (For HL-4570CDW(T))
b
Press + or - to choose Network.
Press OK.
c
Press + or - to choose WLAN.
Press OK.
d
Press + or - to choose Setup Wizard.
Press OK.
e
When WLAN Enable? is displayed, press + to accept.
This will start the wireless setup wizard.
To cancel, press Cancel.
f
The machine will search for your network and display a list of available SSIDs.
Choose <New SSID> using + or -.
Press OK.
g
Enter the SSID name. (For information how to enter text, see the Quick Setup Guide.)
Press OK.
h
Using + or -, choose Ad-hoc or Infrastructure when instructed.
Press OK.
Do one of the following:
If you chose Ad-hoc, go to step j.
If you chose Infrastructure, go to step i.
i
Choose the Authentication method using + or -, and press OK.
Do one of the following:
If you chose Open System, go to step j.
If you chose Shared Key, go to step k.
If you chose WPA/WPA2-PSK, go to step l.
j
Choose the Encryption type None or WEP using + or -, and press OK.
Do one of the following:
If you chose None, go to step n.
If you chose WEP, go to step k.
k
Enter the WEP key you wrote down in step a. Press OK. Go to step n. (For information how to enter
text, see the Quick Setup Guide.)
l
Choose the Encryption type, TKIP or AES using + or -. Press OK. Go to step m.
3
18
Configuring your machine for a wireless network (For HL-4570CDW(T))
m
Enter the WPA key you wrote down in step a and press OK. Go to step n. (For information how to enter
text, see the Quick Setup Guide.)
n
To apply the settings, choose Yes. To cancel, choose No.
Do one of the following:
If you chose Yes, go to step o.
If you chose No, go back to step f.
o
p
The machine starts to connect to the wireless device you have chosen.
3
If your wireless device is connected successfully, the display shows Connected.
The machine will print your machine's wireless status report. If the connection failed, check the error
code on the printed report and refer to Troubleshooting in the Quick Setup Guide.
(Windows®)
You have completed the wireless network setup. If you would like to continue installing the
printer driver, please choose Install Printer Driver from the CD-ROM menu.
(Macintosh)
You have completed the wireless network setup. If you would like to continue installing drivers
and software necessary for operating your device, please choose Start Here OSX from the
CD-ROM menu.
19
Configuring your machine for a wireless network (For HL-4570CDW(T))
Configuring your machine for an enterprise wireless network
a
3
Before configuring your machine we recommend you write down your wireless network settings. You will
need this information before you continue with the configuration.
Check and record the current wireless network settings.
Network name: (SSID, ESSID)
3
Communication Mode
Authentication method
Encryption mode
Infrastructure
LEAP
CKIP
EAP-FAST/NONE
AES
User ID
Password
TKIP
EAP-FAST/MS-CHAPv2
AES
TKIP
EAP-FAST/GTC
AES
TKIP
PEAP/MS-CHAPv2
AES
TKIP
PEAP/GTC
AES
TKIP
EAP-TTLS/CHAP
AES
TKIP
EAP-TTLS/MS-CHAP
AES
TKIP
EAP-TTLS/MS-CHAPv2
AES
TKIP
EAP-TTLS/PAP
AES
TKIP
EAP-TLS
AES
—
TKIP
—
For example:
3
Network name: (SSID, ESSID)
HELLO
Communication Mode
Authentication method
Encryption mode
User ID
Password
Infrastructure
EAP-FAST/MS-CHAPv2
AES
Brother
12345678
20
Configuring your machine for a wireless network (For HL-4570CDW(T))
Note
• If you configure your machine using EAP-TLS Authentication, you must install the Client Certificate before
you start configuration. If you have installed more than one certificate, we recommend you write down the
certificate name you want to use. For installing the certificate, see Using Certificates for device security
on page 60.
• If you verify your machine using the Common Name of the Server Certificate, we recommend you write
down the Common Name before you start configuration. Contact your network administrator about the
Common Name of the Server Certificate.
b
Press + or - to choose Network.
Press OK.
c
Press + or - to choose WLAN.
Press OK.
d
Press + or - to choose Setup Wizard.
Press OK.
e
When WLAN Enable? is displayed, press + to accept.
This will start the wireless setup wizard.
To cancel, press Cancel.
f
The machine will search for your network and display a list of available SSIDs.
You should see the SSID you wrote down earlier. If the machine finds more than one network use + or
- key to choose your network, then press OK. Go to step j.
If your access point is set to not broadcast the SSID, you will have to manually add the SSID name. Go
to step g.
g
Choose <New SSID> using + or -.
Press OK. Go to step h.
h
Enter the SSID name. (For information how to type text, see the Quick Setup Guide.)
Press OK. Go to step i.
i
Using + or -, choose Infrastructure when instructed.
Press OK.
21
3
Configuring your machine for a wireless network (For HL-4570CDW(T))
j
Choose the Authentication method using + or -, and press OK.
Do one of the following:
If you chose LEAP, go to step p.
If you chose EAP-FAST, go to step k.
If you chose PEAP, go to step k.
If you chose EAP-TTLS, go to step k.
If you chose EAP-TLS, go to step l.
k
Choose the Inner Authentication method NONE, CHAP, MS-CHAP, MS-CHAPv2, GTC or PAP using + or -,
and press OK.
Go to step l.
Note
Depending on your Authentication method, the Inner Authentication method selections differ.
l
Choose encryption type TKIP or AES using + or -, and press OK.
Do one of the following:
If your Authentication method is EAP-TLS, go to step m.
For other Authentication methods, go to step n.
m
n
The machine will display a list of available Client Certificates. Choose the certificate and go to step n.
Choose the verification method No Verification, CA or CA + Server ID using + or -, and press
OK.
Do one of the following:
If you chose CA + Server ID, go to step o.
For other selections, go to step p.
Note
If you have not imported a CA certificate in your machine, the machine will display No Verification.
To import a CA certificate, see Using Certificates for device security on page 60.
o
Enter the server ID. (For information how to type text, see the Quick Setup Guide.) Go to step p.
22
3
Configuring your machine for a wireless network (For HL-4570CDW(T))
p
Enter the user ID you wrote down in step a. Press OK. (For information how to type text, see the Quick
Setup Guide.)
Do one of the following:
If your Authentication method is EAP-TLS, go to step r.
For other Authentication methods, go to step q.
q
r
Enter the Password you wrote down in step a. Press OK. Go to step r.
s
t
3
To apply the settings, choose Yes. To cancel, choose No.
Do one of the following:
If you chose Yes, go to step s.
If you chose No, go back to step f.
The machine starts to connect to the wireless network you have chosen.
If your wireless device is connected successfully, the display shows Connected.
The machine will print your machine's wireless status report. If the connection failed, check the error
code on the printed report and refer to Troubleshooting in the Quick Setup Guide.
(Windows®)
You have completed the wireless network setup. If you would like to continue installing the
printer driver, please choose Install Printer Driver from the CD-ROM menu.
(Macintosh)
You have completed the wireless network setup. If you would like to continue installing drivers
and software necessary for operating your device, please choose Start Here OSX from the
CD-ROM menu.
Using the Brother installer application on the CD-ROM to configure your
machine for a wireless network
3
For installation, see Wireless configuration using the Brother installer application (For HL-4570CDW(T))
on page 26.
23
Configuring your machine for a wireless network (For HL-4570CDW(T))
Using the PIN Method of Wi-Fi Protected Setup
3
If your WLAN access point/router supports Wi-Fi Protected Setup (PIN Method), you can configure the
machine easily. The PIN (Personal Identification Number) Method is one of the connection methods
developed by the Wi-Fi Alliance®. By inputting a PIN which is created by an Enrollee (your machine) to the
Registrar (a device that manages the wireless LAN), you can setup the WLAN network and security settings.
See the user’s guide supplied with your WLAN access point/router for instructions on how to access the
Wi-Fi Protected Setup mode.
3
Note
Routers or access points that support Wi-Fi Protected Setup have a symbol as shown below.
a
b
c
d
Press + or - to choose Network.
e
Using a computer that is on the network, type “http://access point’s IP address/” into your
browser. (Where “access point’s IP address” is the IP address of the device that is used as the
Registrar 1) Go to the WPS (Wi-Fi Protected Setup) setting page and input the PIN which the LCD shows
in step d to the Registrar and follow the on-screen instructions.
Press + or - to choose WLAN.
Press + or - to choose WPS w/PIN Code.
The LCD will show an 8 digit PIN and the machine starts searching for a WLAN access point/router for
5 minutes.
1
The Registrar is normally the WLAN access point/router.
Note
The setting page is different, depending on the brand of WLAN access point/router. See the instruction
supplied with your WLAN access point/router.
Windows Vista ®/Windows® 7
3
If you are using your computer as a Registrar, follow these steps:
Note
• To use a Windows Vista® or Windows® 7 computer as a Registrar, you need to register it to your network
in advance. See the instruction supplied with your WLAN access point/router.
• If you use Windows® 7 as a Registrar, you can install the printer driver after the wireless configuration by
following the on-screen instructions. If you want to install the full driver and software package, follow the
steps in Quick Setup Guide for installation.
24
Configuring your machine for a wireless network (For HL-4570CDW(T))
1
(Windows Vista®)
Click the
button and then Network.
® 7)
(Windows
Click the
2
f
button and then Devices and Printers.
(Windows Vista®)
Click Add a wireless device.
(Windows® 7)
Click Add a device.
3
Choose your machine and click Next.
4
Input the PIN which the LCD shows in step d and then click Next.
5
Choose your network that you want to connect to, and then click Next.
6
Click Close.
3
If your wireless device is connected successfully, the display shows Connected.
The machine will print your machine's wireless status report. If the connection failed, check the error
code on the printed report and refer to Troubleshooting in the Quick Setup Guide.
(Windows®)
You have completed the wireless network setup. If you would like to continue installing the
printer driver, please choose Install Printer Driver from the CD-ROM menu.
(Macintosh)
You have completed the wireless network setup. If you would like to continue installing drivers
and software necessary for operating your device, please choose Start Here OSX from the
CD-ROM menu.
25
4
Wireless configuration using the Brother
installer application
(For HL-4570CDW(T))
Before configuring the wireless settings
4
4
IMPORTANT
• The following instructions will install your Brother machine in a network environment using the Brother
installer application found on the CD-ROM we have provided with the machine.
4
• You can also setup your Brother machine using WPS or AOSS™ from the control panel which we
recommend. You can find instructions in the supplied Quick Setup Guide.
• If you have previously configured the wireless settings of the machine, you must reset the network LAN
settings before you can configure the wireless settings again. Press + or - to choose Network,
Network Reset, Reset and then choose Yes to accept the change. The machine will restart
automatically.
• If you are using the Windows® Firewall or a firewall function of anti-spyware or antivirus applications,
temporarily disable them. Once you are sure that you can print please re-enable your firewall.
• You need to temporarily use a USB cable or an Ethernet (LAN) cable during configuration.
• You must know your wireless network settings before you proceed with this installation.
Make sure you take notes on all the current settings such as SSID, authentication and encryption of your
wireless network environment. If you do not know them, contact your network administrator or the
manufacturer of your WLAN access point/router.
Configure the wireless settings
a
4
Before configuring your machine we recommend you write down your wireless network settings. You will
need this information before you continue with the configuration.
Check and record the current wireless network settings.
For a personal wireless network configuration
4
If you are configuring your machine for a smaller wireless network, such as your home environment,
record your SSID and the Network key.
Network name (SSID, ESSID)
Network Key
For example:
4
Network name (SSID, ESSID)
Network Key
HELLO
12345678
26
Wireless configuration using the Brother installer application (For HL-4570CDW(T))
For an enterprise wireless network configuration
4
If you are configuring your machine for an IEEE 802.1x supported wireless network, record your
Authentication method, Encryption method, User ID and Password.
Network name: (SSID, ESSID)
Communication Mode
Authentication method
Encryption mode
Infrastructure
LEAP
CKIP
EAP-FAST/NONE
AES
User ID
Password
4
TKIP
EAP-FAST/MS-CHAPv2
AES
TKIP
EAP-FAST/GTC
AES
TKIP
PEAP/MS-CHAPv2
AES
TKIP
PEAP/GTC
AES
TKIP
EAP-TTLS/CHAP
AES
TKIP
EAP-TTLS/MS-CHAP
AES
TKIP
EAP-TTLS/MS-CHAPv2
AES
TKIP
EAP-TTLS/PAP
AES
TKIP
EAP-TLS
AES
—
TKIP
—
For example:
4
Network name: (SSID, ESSID)
HELLO
Communication Mode
Authentication method
Encryption mode
User ID
Password
Infrastructure
EAP-FAST/MS-CHAPv2
AES
Brother
12345678
27
Wireless configuration using the Brother installer application (For HL-4570CDW(T))
Note
• If you configure your machine using EAP-TLS Authentication, you must install the Client Certificate before
you start configuration. If you have installed more than one certificate, we recommend you write down the
certificate name you want to use. For installing the certificate, see Using Certificates for device security
on page 60.
• If you verify your machine using the Common Name of the Server Certificate, we recommend you write
down the Common Name before you start configuration. Contact your network administrator about the
Common Name of the Server Certificate.
b
4
Put the supplied CD-ROM into your CD-ROM drive.
(Windows®)
4
1 The opening screen will appear automatically.
Choose your machine and the language.
2 The CD-ROM main menu will appear. Click Install Printer Driver.
Note
• If the window does not appear, use Windows® Explorer to run the Start.exe program from the root folder
of the Brother CD-ROM.
• When the User Account Control screen appears,
(Windows Vista®) click Allow.
(Windows® 7) click Yes.
3 When the License Agreement window appears, click Yes if you agree to the License Agreement.
4 Choose Wireless Network Connection and then click Next.
5 Choose Brother Peer-to-Peer Network Printer or Network Shared Printer, and then click Next.
6 When you choose Network Shared Printer, choose your machine’s queue on the Browse for
Printer screen, and then click OK.
Note
Contact your administrator if you are not sure about the location and name of the machine in the network.
7 Choose the option of the Firewall setting in the Firewall/AntiVirus detected screen, and then click
Next.
28
Wireless configuration using the Brother installer application (For HL-4570CDW(T))
(Macintosh)
4
1 The opening screen will appear automatically. Click Start Here OSX. Choose your machine and click
Next.
2 Choose Wireless Network Connection and then click Next.
c
Choose Yes, my Access Point supports WPS or AOSS and I want to use them. or No and then click
Next.
When you choose No, you have the ability to configure the wireless setting in four different ways.
 Using a USB cable temporarily
4
 Using an Ethernet (LAN) cable temporarily
 Configuring through the control panel manually
 Using Ad-hoc mode
Note
For Ad-hoc setup users:
• If a message to restart your computer appears after the wireless settings have been changed, restart
your computer and then go back to step b.
• You can temporarily change the wireless settings on your computer.
(Windows Vista® and Windows ® 7)
1
Click the
2
Click Network and Internet and then the Network and Sharing Center icon.
3
Click Connect to a network.
4
You can see the SSID of the wireless machine on the list. Choose SETUP and then click Connect.
5
(For Windows Vista® only )
Click Connect Anyway and then Close.
6
(Windows Vista®)
Click View status of Wireless Network Connection (SETUP).
7
(Windows® 7)
Click Wireless Network Connection (SETUP).
8
Click Details.... and confirm the Network Connection Details screen. It may take a few minutes
to change from 0.0.0.0 to the 169.254.x.x IP address to be shown on screen (where x.x. are
numbers between 1 and 254).
button and then Control Panel.
29
Wireless configuration using the Brother installer application (For HL-4570CDW(T))
(Windows® XP SP2)
1
Click Start and then Control Panel.
2
Click the Network and Internet Connections icon.
3
Click the Network Connections icon.
4
Choose and right-click Wireless Network Connection. Click View Available Wireless
Networks.
5
You can see the SSID of the wireless printer in the list. Choose SETUP and click Connect.
6
Check the Wireless Network Connection status. It may take a few minutes to change from
0.0.0.0 to the 169.254.x.x IP address to be shown on screen (where x.x. are numbers between 1
and 254).
4
(Macintosh)
d
1
Click the AirPort status icon in the menu bar.
2
Select SETUP from the pop-up menu.
3
Your wireless network is connected successfully.
Follow the screen instructions to configure the wireless settings.
After you have completed the wireless setup, you can proceed to the printer driver installation.
Click Next in the installation dialog and follow the screen instructions.
30
5
Control panel setup
5
Network menu
5
The Network menu selections of the control panel allow you to set up the Brother machine for your network
configuration. (For more information on how to use the control panel, see the User's Guide.) Press any of the
Menu buttons (+, -, OK or Back) to display the main menu. Then press + or - to choose Network. Proceed
to the menu selection you wish to configure. (For additional information on the menu, see Function table and
default factory settings on page 37.)
Please note that the machine is supplied with the BRAdmin Light utility or Web Based Management
applications, which also can be used to configure many aspects of the network. (See Other Management
Utilities on page 6.)
5
TCP/IP
5
If you connect the machine with a network cable to your network, use the Wired LAN menu selections. If
you connect the machine to a wireless Ethernet network, use the WLAN menu selections.
Boot Method
5
This selection controls how the machine obtains an IP address.
Auto mode
5
In this mode, the machine will scan the network for a DHCP server, if it can find one, and if the DHCP server
is configured to allocate an IP address to the machine, then the IP address supplied by the DHCP server will
be used. If no DHCP server is available, then the machine will scan for a BOOTP server. If a BOOTP server
is available, and it is configured correctly, the machine will take its IP address from the BOOTP server. If a
BOOTP server is not available, the machine will scan for a RARP server. If a RARP server also does not
answer, the IP Address is set using the APIPA protocol. After the machine is initially powered ON, it may take
a few minutes for the machine to scan the network for a server.
Static mode
5
In this mode the machine’s IP address must be manually assigned. Once entered the IP address is locked to
the assigned address.
Note
If you do not want your print server configured via DHCP, BOOTP or RARP, you must set the
Boot Method to Static so that the print server has a static IP address. This will prevent the print server
from trying to obtain an IP address from any of these systems. To change the Boot Method, use the
machine’s control panel, BRAdmin Light utility or Web Based Management.
31
Control panel setup
IP Address
5
This field displays the current IP address of the machine. If you have chosen a Boot Method of Static,
enter the IP address that you wish to assign to the machine (check with your network administrator for the IP
address to use). If you have chosen a method other than Static, the machine will attempt to determine its
IP address using the DHCP or BOOTP protocols. The default IP address of your machine will probably be
incompatible with the IP address numbering scheme of your network. We recommend that you contact your
network administrator for an IP address for the network the unit will be connected on.
Subnet Mask
5
This field displays the current subnet mask used by the machine. If you are not using DHCP or BOOTP to
obtain the subnet mask, enter the desired subnet mask. Check with your network administrator for the subnet
mask to use.
Gateway
5
5
This field displays the current gateway or router address used by the machine. If you are not using DHCP or
BOOTP to obtain the gateway or router address, enter the address you wish to assign. If you do not have a
gateway or router, leave this field blank. Check with your network administrator if you are unsure.
IP Boot Tries
5
This field displays how many times the machine attempts to scan the network to obtain the IP address through
the Boot Method you have set. (See Boot Method on page 31).
APIPA
5
The setting of On will cause the print server to automatically allocate a Link-Local IP address in the range
(169.254.1.0 - 169.254.254.255) when the print server cannot obtain an IP address through the Boot Method
you have set. (See Boot Method on page 31.) Choosing Off means the IP address does not change, when
the print server cannot obtain an IP address through the Boot Method you have set.
IPv6
5
This machine is compatible with IPv6, the next generation Internet protocol. If you want to use the IPv6
protocol, choose On. The default setting for IPv6 is Off. For more information on the IPv6 protocol, visit
http://solutions.brother.com/.
Note
• If you set IPv6 to On, turn off the power switch and then turn it back on to enable this protocol.
• After you choose IPv6 On, this setting will be applied to both the wired and wireless LAN interface.
32
Control panel setup
Ethernet (wired network only)
5
Ethernet link mode. Auto allows the print server to operate in 100BASE-TX full or half duplex, or in 10BASE-T
full or half duplex mode by auto negotiation.
Note
If you incorrectly set this value, you may not be able to communicate with your print server.
Status (For HL-4140CN and HL-4150CDN)/Wired Status (For HL-4570CDW(T))
5
This field displays the current wired network status.
5
Setup Wizard (wireless network only)
5
The Setup Wizard guides you through the wireless network configuration. (For more information, see the
Quick Setup Guide or Using the Setup Wizard from the control panel on page 16.)
WPS or AOSS™ (wireless network only)
5
If your WLAN access point/router supports either Wi-Fi Protected Setup (PBC 1) or AOSS™ (Automatic
Wireless mode), you can configure the machine easily without a computer. (For more information, see the
Quick Setup Guide or Using WPS or AOSS™ from the control panel menu to configure your machine for a
wireless network (Automatic Wireless mode) on page 16.)
1
Push Button Configuration
WPS w/PIN Code (wireless network only)
5
If your WLAN access point/router supports Wi-Fi Protected Setup (PIN Method), you can configure the
machine easily without a computer. (For more information, see Using the PIN Method of Wi-Fi Protected
Setup on page 24.)
WLAN Status (wireless network only)
Status
5
5
This field displays the current wireless network status.
Signal
5
This field displays the current wireless network signal strength.
33
Control panel setup
Channel
5
This field displays the current wireless network channel.
Speed
5
This field displays the current wireless network speed.
SSID
5
This field displays the current wireless network SSID. The display shows up to 32 characters of the SSID
name.
Comm.Mode
5
This field displays the current wireless network communication mode.
MAC Address
5
The MAC address is a unique number assigned for the machine's network interface. You can check your
machine's MAC address from the control panel.
Set to Default (For HL-4570CDW(T))
5
The Set to Default allows you to reset each wired or wireless settings to the factory default. If you want
to reset both wired and wireless settings, see Reset the network settings to the factory default on page 35.
Wired Enable (For HL-4570CDW(T))
5
If you want to use the wired network connection, set Wired Enable to On.
WLAN Enable (For HL-4570CDW(T))
5
If you want to use the wireless network connection, set WLAN Enable to On.
Note
If a network cable is connected to your machine, set Wired Enable to Off.
34
5
Control panel setup
Reset the network settings to the factory default
5
You can reset the print server back to its default factory settings (resetting all information such as the
password and IP address information).
Note
• This function resets all wired and wireless network settings to the factory default.
• You can also reset the print server back to its factory default settings using the BRAdmin applications or
Web Based Management. (For more information, see Other Management Utilities on page 6.)
a
Press + or - to choose Network.
Press OK.
b
Press + or - to choose Network Reset.
Press OK.
c
d
e
Press + to choose Reset.
5
Press + to choose Yes for reboot.
The machine will re-start.
Printing the Network Configuration List
5
Note
Node name: The Node name appears on the Network Configuration List. The default node name is
“BRNxxxxxxxxxxxx” for a wired network or “BRWxxxxxxxxxxxx” for a wireless network. (“xxxxxxxxxxxx” is
your machine’s MAC Address / Ethernet Address.)
The Network Configuration List prints a report listing all the current network configuration including the
network print server settings.
a
Press + or - to choose Machine Info..
Press OK.
b
Press + or - to choose Print NetSetting.
Press OK.
Note
If the IP Address on the Network Configuration List shows 0.0.0.0, wait for one minute and try again.
35
Control panel setup
Printing the WLAN report (For HL-4570CDW(T))
5
The Print WLANReport prints your machine's wireless status report. If the wireless connection failed,
check the error code on the printed report and refer to Troubleshooting in the Quick Setup Guide.
a
Press + or - to choose Machine Info..
Press OK.
b
Press + or - to choose Print WLANReport.
Press OK.
5
36
Control panel setup
Function table and default factory settings
HL-4140CN and HL-4150CDN
5
5
Factory settings are shown in Bold with asterisk.
Main menu
Submenu
Menu Selections
Options
Network
TCP/IP
Boot Method
Auto*/Static/RARP/BOOTP/DHCP
IP Address
(000.000.000.000)* 1
Subnet Mask
(000.000.000.000)* 1
Gateway
(000.000.000.000)* 1
IP Boot Tries
0/1/2/3*.../32767
APIPA
On*/Off
IPv6
Off*/On
Ethernet
Auto*/100B-FD/100B-HD/10B-FD/10B-HD
Status
Active 100B-FD/Active 100B-HD/
Active 10B-FD/Active 10B-HD/Inactive
5
MAC Address
Network Reset
1
Restores all network settings of the internal print server to the factory
default.
On connection to the network, the machine will automatically set the IP address and Subnet Mask to values appropriate for your network.
37
Control panel setup
HL-4570CDW(T)
5
Factory settings are shown in Bold with asterisk.
Main menu
Submenu
Menu Selections
Network
Wired LAN
TCP/IP
Options
Boot Method
Auto*/Static/RARP/BOOTP/DHCP
IP Address
(000.000.000.000)* 1
Subnet Mask
(000.000.000.000)* 1
Gateway
(000.000.000.000)* 1
IP Boot Tries
0/1/2/3*.../32767
APIPA
On*/Off
IPv6
Off*/On
Ethernet
Auto*/100B-FD/100B-HD/
10B-FD/10B-HD
Wired Status
Active 100B-FD/
Active 100B-HD/
Active 10B-FD/
Active 10B-HD/Inactive/
Wired OFF
5
MAC Address
Set to Default
Wired Enable
Restores wired network settings of the internal print server
to the factory default.
On*/Off
38
Control panel setup
Main menu
Submenu
Menu Selections
Network
WLAN
TCP/IP
Options
Boot Method
Auto*/Static/RARP/BOOTP/DHCP
IP Address
(000.000.000.000)* 1
Subnet Mask
(000.000.000.000)* 1
Gateway
(000.000.000.000)* 1
IP Boot Tries
0/1/2/3*.../32767
APIPA
On*/Off
IPv6
Off*/On
Setup Wizard
5
WPS/AOSS
WPS w/PIN Code
WLAN Status
Status
Signal
Channel
(Appears only when
WLAN Enable is On.)
Speed
SSID
Comm. Mode
Ad-hoc/Infrastructure
MAC Address
Set to Default
WLAN Enable
Restores wireless network settings of the internal print
server to the factory default.
Off*/On
Network Reset Restores all network settings of the internal print server to the factory default.
1
On connection to the network, the machine will automatically set the IP address and Subnet Mask to values appropriate for your network.
39
6
Web Based Management
6
Overview
6
A standard Web Browser can be used to manage your machine using the HTTP (Hyper Text Transfer
Protocol). You can get the following information from a machine on your network using a web browser.
 Machine status information
 Change network settings such as TCP/IP information
 Configure Secure Function Lock 2.0
 Configure Store Print Log to Network
 Software version information of the machine and print server
 Change network and machine configuration details
6
Note
We recommend Microsoft® Internet Explorer® 6.0 (or greater) or Firefox 3.0 (or greater) for Windows® and
Safari 3.0 (or greater) for Macintosh. Please also make sure that JavaScript and Cookies are always
enabled in whichever browser you use. If a different web browser is used, make sure it is compatible with
HTTP 1.0 and HTTP 1.1.
You must use the TCP/IP protocol on your network and have a valid IP address programmed into the print
server and your computer.
How to configure the machine settings using Web Based
Management (web browser)
6
A standard web browser can be used to change your print server settings using the HTTP (Hyper Text
Transfer Protocol).
Note
We recommend to use HTTPS protocol for your Internet security when configuring the settings using Web
Based Management. To enable the HTTPS protocol, see Managing your network machine securely using
SSL/TLS on page 52.
a
b
Start your web browser.
Type “http://machine’s IP address/” into your browser (where “machine’s IP address” is
the machine’s IP address).
 For example:
http://192.168.1.2/
40
Web Based Management
Note
• If you are using a Domain Name System or enable a NetBIOS name, you can enter another name such
as “Shared_Printer” instead of the IP address.
• For example:
http://Shared_Printer/
If you enable a NetBIOS name, you can also use the node name.
• For example:
http://brnxxxxxxxxxxxx/
The NetBIOS name can be seen in the Network Configuration List. (To learn how to print the Network
Configuration List, see Printing the Network Configuration List on page 35.)
• For Macintosh users, you can have easy access to the Web Based Management System by clicking the
machine icon on the Status Monitor screen. For more information, see the User's Guide.
c
d
Click Network Configuration.
e
f
Click OK.
Enter a user name and a password. The default User Name is “admin” and the default password is
“access”.
You can now change the print server settings.
Note
If you have changed the protocol settings, restart the machine after clicking Submit to activate the
configuration.
41
6
Web Based Management
Secure Function Lock 2.0
6
Secure Function Lock 2.0 from Brother helps you to save money and increase security by restricting the
functions available on your Brother machine.
Secure Function Lock allows you to configure passwords for selected users, granting them access to some,
or all, of these functions, or limiting them to a page limit. This means that only authorized people can use
them.
You can configure and change the following Secure Function Lock 2.0 settings using BRAdmin
Professional 3 or Web Based Management.
 PC Print 1
 USB Direct Print
 Color Print
6
 Page Limit
 Page Counter
1
If you register the PC user login names, you can restrict PC print without the user entering a password. For more detail, see Restricting PC print
by PC user login name on page 43.
How to configure the Secure Function Lock 2.0 settings using Web Based
Management (web browser)
6
Basic configuration
a
b
c
6
Click Administrator Settings on the machine’s web page, and then click Secure Function Lock.
Choose On from Function Lock.
Enter an up to 15 digit alphanumeric group name or user name in the ID Number/Name box and then
enter a four-digit password in the PIN box.
d
Uncheck the functions that you want to restrict in the Print box. If you want to configure the maximum
page count, check the On box in Page Limit, and then enter the number in the Max. box. Then click
Submit.
e
If you want to restrict the PC printing by PC user login name, click PC Print Restriction by Login Name
and configure the settings. (See Restricting PC print by PC user login name on page 43.)
42
Web Based Management
Restricting PC print by PC user login name
6
By configuring this setting, the machine can authenticate by PC user login name to allow a print job from a
registered computer.
a
Click PC Print Restriction by Login Name. The PC Print Restriction by Login Name screen will
appear.
b
c
Choose On from PC Print Restriction.
d
Choose the ID Number you set in the ID Number/Name in step c in Basic configuration from the
ID Number pull-down list for each Login Name and then enter the PC user login name in the
Login Name box.
Click Submit.
Note
• If you want to restrict PC print per group, choose the same ID Number for each PC login name you want
in the group.
6
• If you are using the PC login name feature you must also make sure that the Use PC Login Name box in
the printer driver is checked. For more information about the printer driver, see the User's Guide.
• The Secure Function Lock feature does not support the BR-Script driver for printing.
Setting up public mode
6
You can set up the public mode to restrict what functions are available for public users. Public users do not
need to enter a password to access the features made available through this setting.
a
b
Uncheck the check box for the function that you want to restrict in the Public Mode box.
Click Submit.
Other features
6
You can set up the following features in Secure Function Lock 2.0:
 All Counter Reset
You can reset the page counter by clicking All Counter Reset.
 Export to CSV file
You can export the current page counter including ID Number/Name information as a CSV file.
 Last Counter Record
The machine retains the page count after the counter has been reset.
 Counter Auto Reset Settings
You can automatically reset the page counters by configuring the time interval based on Daily, Weekly or
Monthly settings during the machine is turned on.
43
Web Based Management
Synchronize with SNTP server
6
SNTP is the protocol used to synchronize the time used by the machine for Authentication with the SNTP
time server. You can synchronize the time used by the machine on a regular basis with the Coordinated
Universal Time (UTC) provided by the SNTP time server.
Note
This function is not available in some countries.
a
b
c
Click Network Configuration, and then click Configure Protocol.
Select the SNTP check box to activate the setting.
Click Advanced Setting.
 Status
6
Displays whether the SNTP server settings are enabled or disabled.
 SNTP Server Method
Choose AUTO or STATIC.
• AUTO
If you have a DHCP server in your network, the SNTP server will automatically obtain the address
from that server.
• STATIC
Enter the address you want to use.
 Primary SNTP Server Address, Secondary SNTP Server Address
Enter the server address (up to 64 characters).
 Primary SNTP Server Port, Secondary SNTP Server Port
Enter the Port number (1 to 65535).
44
Web Based Management
 Synchronizing Interval
Enter the interval of hours which you want to synchronize to the server (1 to 168 hours).
Note
• You must configure Date&Time to synchronize the time used by the machine with the SNTP time server.
Click Configure Date&Time and then configure Date&Time on the General Setup screen.
6
• Choose the Synchronize with SNTP server check box. You also need to verify your time zone settings
correctly. Choose the time difference between your location and UTC from the Time Zone pull-down list.
For example, the time zone for Eastern Time in the USA and Canada is UTC-05:00.
 Synchronization Status
You can confirm the latest synchronization status.
d
Click Submit to apply the settings.
45
Web Based Management
Store Print Log to Network
6
The Store Print Log to Network feature allows you to save the print log file from your Brother machine to a
network server using CIFS 1. You can record the ID, type of print job, job name, user name, date, time, the
number of printed pages and color pages 2 for every print job.
1
CIFS is the Common Internet File System protocol that runs over TCP/IP allowing computers on a network to share files over an intranet or the
Internet.
2
Supported models only.
The following print functions are recorded in the print log:
 Print jobs from your computer
 USB Direct Print
Note
• The Store Print Log to Network feature supports Kerberos Authentication and NTLMv2 Authentication.
6
You must configure the SNTP protocol (network time server), or you must set the date, time and time zone
correctly for Authentication.
• You can set the file type to TXT or CSV when storing a file to the server.
How to configure the Store Print Log to Network settings using Web Based
Management (web browser)
a
b
c
6
Click Administrator Settings on the machine’s web page, and then click Store Print Log to Network.
Choose On from Print Log.
You can configure the following settings using a web browser.
 Host Address
The Host Address is the Host name of the CIFS server. Enter the Host Address (for example:
example.com) (up to 64 characters) or the IP address (for example: 192.168.56.189).
 Store Directory
Enter the destination folder where your log will be stored on the CIFS server (for example:
brother\abc) (up to 60 characters).
 File Name
Enter the file name you want to use for the print log up to 15 characters.
 File Type
Choose the file type for the print log TXT or CSV.
46
Web Based Management
 Auth. Method
Choose the authentication method required for access to the CIFS server Auto, Kerberos 1 or
NTLMv2 2.
1
Kerberos is an authentication protocol which allows devices or individuals to securely prove their identity to network servers using a
single sign-on.
2
NTLMv2 is the default authentication method used by Windows to log into servers.
For Kerberos and NTLMv2 Authentication you must also configure the Date&Time settings or
the SNTP protocol (network time server).
You can configure the Date&Time and the SNTP settings using Web Based Management.
• Auto: If you choose Auto, the machine will initially search for a Kerberos server. If the Kerberos
server is not detected, NTLMv2 will be used for the authentication method.
6
• Kerberos: Choose Kerberos, to use Kerberos authentication only.
• NTLMv2: Choose NTLMv2, to use NTLMv2 authentication only.
 Username
Enter the Username for the authentication up to 96 characters.
Note
If the username is part of a domain, please input the username in one of the following styles: user@domain
or domain\user.
 Password
Enter the password for the authentication up to 32 characters.
 Kerberos Server Address (if needed)
Enter the KDC Host Address (for example: example.com) (up to 64 characters) or the IP address (for
example: 192.168.56.189).
d
In the Connection Status, you can confirm the last log status. For more information, see Understanding
Error Messages on page 49.
e
Click Submit to apply your settings.
47
Web Based Management
Error Detection Setting
6
You can choose what action is taken when the print log cannot be stored to the server due to a network error.
a
Choose Cancel Print or Ignore Log & Print in the Error Detection Setting of Store Print Log to
Network.
 Cancel Print
If you choose Cancel Print, the print jobs are canceled when the print log cannot be stored to the
server.
 Ignore Log & Print
If you choose Ignore Log & Print, the machine prints the document even if the print log cannot be
stored to the server.
When the store print log function has recovered, the print log is recorded as follows:
• If the log cannot be stored at the end of printing, the print log except the number of printed pages
and color pages will be recorded. (1)
• If the Print Log cannot be stored at the beginning and the end of printing, the print log of the job
will not be recorded. When the function has recovered, the occurrence of an error is shown in the
log. (2)
Example of the print log:
(1)
(2)
b
Click Submit to apply your settings.
48
6
Web Based Management
Understanding Error Messages
6
You can confirm the error status on the LCD of your machine or Connection Status in Web Based
Management.
 Server Timeout
This message will appear when you cannot connect to the server.
Make sure that:
• Your server address is correct.
• Your server is connected to the network.
• The machine is connected to the network.
 Authentication Error
The message will appear when your Authentication Setting is not correct.
Make sure that:
6
1
• Username and Password in Authentication Setting is correct.
1
If the username is part of a domain, please input the username in one of the following styles: user@domain or domain\user.
• Confirm the time of the log file sever matches the time from the SNTP server, or the Date&Time
settings.
• Confirm the SNTP time server settings are configured correctly so the time matches the time used for
authentication by Kerberos or NTLMv2. If there is no SNTP server make sure the Date&Time and
Time Zone settings are set correctly using Web Based Management so the machine matches the time
being used by the server providing the authentication.
 File Access Error
This message will appear when you cannot access the destination folder.
Make sure that:
• Directory name is correct.
• Directory is write-enabled.
• File is not locked.
 Wrong Date&Time
This message will appear when your machine does not obtain the time from the SNTP time server. Make
sure that:
• Confirm the settings to access the SNTP time correctly using Web Based Management.
• If no SNTP server is being used, confirm the Date & Time set or from Web Based Management matches
the time used by the server providing the authentication.
Note
If you choose the Cancel Print option in Web Based Management the Log Access Error message will
remain on the LCD for about 30 seconds.
49
Web Based Management
Using Store Print Log to Network with Secure Function Lock 2.0
6
When Secure Function Lock 2.0 is active the names of the registered users for and USB Direct Print functions
will be recorded in the Store Print Log to Network report.
Example of the print Log with Secure Function Lock 2.0 users:
6
50
7
Security features
7
Overview
7
In today’s world there are many security threats to your network and the data that travels over it. Your Brother
machine employs some of the latest network security and encryption protocols available today. These
network features can be integrated into your overall network security plan to help protect your data and
prevent unauthorized access to the machine. This chapter explains how to configure them.
You can configure the following security features:
 Managing your network machine securely using SSL/TLS (See Managing your network machine securely
using SSL/TLS on page 52.)
 Managing your network machine securely using SNMPv3 protocol (See Secure Management using
Web Based Management (web browser) on page 52 or Secure Management using BRAdmin
Professional 3 (Windows®) on page 59.)
 Printing documents securely using SSL/TLS (See Printing documents securely using SSL/TLS
on page 54.)
7
 Sending and Receiving an E-mail securely (See Sending or Receiving an E-mail securely on page 55.)
 Using IEEE 802.1x authentication (See Using IEEE 802.1x authentication on page 57.)
 Secure Management using BRAdmin Professional 3 (Windows®) (See Secure Management using
BRAdmin Professional 3 (Windows®) on page 59.)
 Certificate for secure management (See Using Certificates for device security on page 60.)
 Managing multiple certificates (See Managing multiple certificates on page 69.)
Note
We recommend to disable the Telnet, FTP and TFTP protocols. Accessing the machine using these
protocols is not secure. (For how to configure the protocol settings, see How to configure the machine
settings using Web Based Management (web browser) on page 40.)
51
Security features
Managing your network machine securely using SSL/TLS
7
To manage your network machine securely, you need to use the management utilities with security protocols.
Secure Management using Web Based Management (web browser)
7
We recommend to use HTTPS and SNMPv3 protocol for secure management. To use the HTTPS protocol,
the following machine settings are required.
 A self-signed certificate or a certificate issued by a CA, and a private key must be installed in the machine.
(For how to install a certificate and private key, see Using Certificates for device security on page 60.)
 The HTTPS protocol must be enabled. To enable the HTTPS protocol, choose an installed certificate from
the pull-down list in the HTTP Server Settings page of Web Based Management on the
Configure Protocol page, and then enable SSL communication is used (port 443). (For information on
how to access the Configure Protocol page, see How to configure the machine settings using
Web Based Management (web browser) on page 40.)
a
b
7
Start your web browser.
Type “https://Common Name/” into your browser. (Where “Common Name” is the Common Name
that you assigned for the certificate, such as an IP address, node name or domain name. For how to
assign a Common Name for the certificate, see Using Certificates for device security on page 60.)
 For example:
https://192.168.1.2/ (if the Common Name is the printer’s IP address)
c
You can now access the machine using HTTPS.
We recommend secure management (SNMPv3) be used along with the HTTPS protocol. If you use the
SNMPv3 protocol, follow the steps below.
Note
You can also change the SNMP settings by using BRAdmin Professional 3 or Web BRAdmin.
d
e
Click Network Configuration.
f
Click Configure Protocol.
Enter a user name and a password. The default User Name is “admin” and the default Password is
“access”.
52
Security features
g
h
Make sure that the SNMP setting is enabled, and then click Advanced Setting of SNMP.
You can configure the SNMP settings from the screen below.
7
We have three SNMP connection modes of operation.
7
 SNMPv3 read-write access
With this mode the print server uses version 3 of the SNMP protocol. If you want to manage the print server
securely, use this mode.
Note
When you use the SNMPv3 read-write access mode, please note the following.
• You can manage the print server by using BRAdmin Professional 3, Web BRAdmin or Web Based
Management only.
• We recommend secure SSL communication (HTTPS) be used.
• Except for BRAdmin Professional 3 and Web BRAdmin, all applications that use SNMPv1/v2c will be
restricted. To allow the use of SNMPv1/v2c applications, use SNMPv3 read-write access and v1/v2c
read-only access or SNMPv1/v2c read-write access mode.
53
Security features
 SNMPv3 read-write access and v1/v2c read-only access
In this mode the print server uses the read-write access of version 3 and the read-only access of version 1
and version 2c of the SNMP protocol.
Note
When you use the SNMPv3 read-write access and v1/v2c read-only access mode, some Brother
applications (e.g. BRAdmin Light) that access to the print server do not work properly since they authorize
the read-only access of version 1 and version 2c. If you want to use all applications, use the SNMPv1/v2c
read-write access mode.
 SNMPv1/v2c read-write access
In this mode the print server uses version 1 and version 2c of the SNMP protocol. You can use all Brother
applications under this mode. However, it is not secure since it will not authenticate the user and the data
will not be encrypted.
Note
For more information, see the Help text in Web Based Management.
7
Printing documents securely using SSL/TLS
7
To print documents securely over the Internet, you can use the IPPS protocol.
Note
• Communication using IPPS cannot prevent unauthorized access to the print server.
• IPPS is available for Windows® 2000/XP, Windows Vista®, Windows® 7 and Windows Server®
2003/2008.
To use the IPPS protocol, the following machine settings are required.
 A self-signed certificate or a certificate issued by a CA, and a private key must be installed in the machine.
For how to install a certificate and private key, see Using Certificates for device security on page 60.
 The IPPS protocol must be enabled. To enable the IPPS protocol, choose an installed certificate from the
pull-down list in the HTTP Server Settings page of IPP on the Configure Protocol page, and then enable
SSL communication is used (port 443). For information on how to access the Configure Protocol
page, see How to configure the machine settings using Web Based Management (web browser)
on page 40.
54
Security features
Sending or Receiving an E-mail securely
7
Configuration using Web Based Management (web browser)
7
You can configure secured E-mail sending with user authentication or E-mail sending and receiving using
SSL/TLS on the Web Based Management screen.
a
b
Start your web browser.
Type “http://printer’s IP address/” into your browser (where “printer’s IP address” is
the printer’s IP address).
 For example:
http://192.168.1.2/
c
d
Click Network Configuration.
e
f
g
Click Configure Protocol.
Enter a user name and a password. The default User Name is “admin” and the default Password is
“access”.
7
Click Advanced Setting of POP3/SMTP and make sure that the status of POP3/SMTP is Enable.
You can configure the POP3/SMTP settings on this page.
Note
• For more information, see the Help text in Web Based Management.
• You can also confirm whether the E-mail settings are correct after configuration by sending a test E-mail.
h
i
After configuring, click Submit. The Test E-mail Send/Receive Configuration dialog appears.
Follow the instructions on-screen if you want to test with the current settings.
Sending an E-mail with user authentication
7
This machine supports POP before SMTP and SMTP-AUTH methods to send an E-mail via an E-mail server
that requires a user authentication. These methods prevent an unauthorized user from accessing the E-mail
server. You can use Web Based Management, BRAdmin Professional 3 and Web BRAdmin to configure
these settings. You can use POP before SMTP and SMTP-AUTH methods for E-mail Notification and E-mail
reports.
E-mail server settings
You need to match the settings of SMTP authentication method with the method used by your E-mail server.
Contact your network administrator or your ISP (Internet Service Provider) about the E-mail server
configuration.
You will also need to check SMTP-AUTH of SMTP Server Authentication Method to enable the SMTP
server authentication.
55
Security features
SMTP settings
 You can change the SMTP port number using Web Based Management. This is useful if your ISP (Internet
Service Provider) implements the “Outbound Port 25 Blocking (OP25B)” service.
 By changing the SMTP port number to a specific number which your ISP is using for the SMTP server (for
example, port 587), you would then be able to send an E-mail via the SMTP server.
 If you can use both POP before SMTP and SMTP-AUTH, we recommend choosing SMTP-AUTH.
 If you choose POP before SMTP for the SMTP Server Authentication Method, you need to configure the
POP3 settings. You can also use the APOP method if needed.
Sending or Receiving an E-mail securely using SSL/TLS
7
This machine supports SSL/TLS methods to send or receive an E-mail via an E-mail server that requires
secure SSL/TLS communication. To send or receive E-mail via an E-mail server that is using SSL/TLS
communication, you must configure SMTP over SSL/TLS or POP3 over SSL/TLS correctly.
Verifying Server Certificate
 If you choose SSL or TLS for SMTP over SSL/TLS or POP3 over SSL/TLS, the Verify Server Certificate
check box will be automatically checked to verify the Server Certificate.
• Before you verify the Server Certificate, you must import the CA certificate that has been issued by the
CA that signed the Server Certificate. Contact your system administrator about the CA certificate. For
importing the certificate, see Import and export a CA certificate on page 70.
• If you do not need to verify the Server Certificate, uncheck Verify Server Certificate.
Port Number
 If you choose SSL or TLS, the SMTP Port or POP3 Port value will be changed to match the protocol. If
you want to change the port number manually, enter the port number after you choose SMTP over
SSL/TLS or POP3 over SSL/TLS.
 You must configure the POP3/SMTP communication method to match the E-mail server. For details of the
E-mail server settings, contact your network administrator or Internet services provider.
In most cases, the secured webmail services require the following settings:
(SMTP)
SMTP Port: 587
SMTP Server Authentication Method: SMTP-AUTH
SMTP over SSL/TLS: TLS
(POP3)
POP3 Port: 995
POP3 over SSL/TLS: SSL
56
7
Security features
Using IEEE 802.1x authentication
7
You can configure IEEE 802.1x authentication for a wired or a wireless network.
To use IEEE 802.1x authentication, you must install a certificate issued by a CA. Contact your network
administrator or your ISP (Internet Service Provider) whether a CA certificate import is necessary. (For how
to install a certificate, see Using Certificates for device security on page 60.)
IEEE 802.1x authentication configuration using Web Based Management (web
browser)
7
If you are configuring IEEE 802.1x authentication for a wired or a wireless network using Web Based
Management, follow the instructions.
You can also configure IEEE 802.1x authentication using:
(Wired network)
 BRAdmin Professional 3
7
(Wireless network)
 Wireless setup wizard from the control panel (For details, see Configuring your machine for an enterprise
wireless network on page 20.)
 Wireless setup wizard on the CD-ROM (For details, see Wireless configuration using the Brother installer
application (For HL-4570CDW(T)) on page 26.)
 BRAdmin Professional 3
Note
• If you configure your machine using EAP-TLS Authentication, you must install the Client Certificate before
you start configuration. If you have installed more than one certificate, we recommend you write down the
certificate you want to use. For installing the certificate, see Using Certificates for device security
on page 60.
• Before you verify the Server Certificate, you must import the CA certificate that has been issued by the CA
that signed the Server Certificate. Contact your system administrator about the CA certificate. For
importing the certificate, see Import and export a CA certificate on page 70.
• For the details of each certificate, see Using Certificates for device security on page 60.
a
b
Start your web browser.
Type “http://machine’s IP address/” into your browser (where “machine’s IP address” is
the machine’s IP address).
 For example:
http://192.168.1.2/
57
Security features
Note
• If you are using a Domain Name System or enable a NetBIOS name, you can enter another name such
as “Shared_Printer” instead of the IP address.
• For example:
http://Shared_Printer/
If you enable a NetBIOS name, you can also use the node name.
• For example:
http://brnxxxxxxxxxxxx/
The NetBIOS name can be seen in the Network Configuration List. (To learn how to print the Network
Configuration List, see Printing the Network Configuration List on page 35.)
• For Macintosh users, you can have easy access to the Web Based Management System by clicking the
machine icon on the Status Monitor screen. For more information, see the User's Guide.
c
d
Click Network Configuration.
e
(Wired) Click Configure Wired802.1x.
(Wireless) Click Configure Wireless and the Enterprise tab.
f
Now you can configure the IEEE 802.1x authentication settings.
7
Enter a user name and a password. The default User Name is “admin” and the default password is
“access”.
 If you want to enable IEEE 802.1x authentication for wired network, check Enable for Wired 802.1x
status on the Configure Wired802.1x page.
 For the details of IEEE 802.1x authentication and the inner authentication methods, see the Network
Glossary.
 If you are using EAP-TLS authentication, you must choose the Client Certificate that has been
installed (shown with Certificate Name) for verification from the Client Certificate pull-down list.
 If you choose EAP-FAST, PEAP, EAP-TTLS or EAP-TLS authentication, you can choose the
verification method from the Server Certificate Verification pull-down list. You can verify the Server
Certificate by using the CA certificate imported to the machine in advance, that has been issued by
the CA that signed the Server Certificate.
You can choose following verification methods from the Server Certificate Verification pull-down list.
 No Verification
The Server Certificate can always be trusted. The verification is not performed.
 CA Cert.
The verification method to check the CA reliability of the Server Certificate, using the CA certificate
that has been issued by the CA that signed the Server Certificate.
58
Security features
 CA Cert. + ServerID
The verification method to check the Common Name 1 value of the Server Certificate, in addition to
the CA reliability of the Server Certificate.
1
g
The Common Name verification compares the Common Name of the Server Certificate to the character string configured for the Server ID.
Before you use this method, contact your system administrator about the Server Certificate’s Common Name and then configure Server ID.
After configuring, click Submit.
(Wired)
After configuring, connect your machine to the IEEE 802.1x supported network. After a few minutes, print
the Network Configuration List to check the <Wired IEEE 802.1x> Status. (See Printing the Network
Configuration List on page 35 for information on how to print the Network Configuration List on your print
server.)
 Success
The wired IEEE 802.1x function is enabled and the authentication was successful.
 Failed
The wired IEEE 802.1x function is enabled, however, the authentication failed.
7
 Off
The wired IEEE 802.1x function is not available.
(Wireless)
Shortly after configuring, WLAN report will be printed automatically. Check your wireless configuration
on the report. See Printing the WLAN report (For HL-4570CDW(T)) on page 36.
Secure Management using BRAdmin Professional 3
(Windows®)
7
To use the BRAdmin Professional 3 utility securely, you need to follow the
points below
7
 We strongly recommend to use the latest version of the BRAdmin Professional 3 utility or Web BRAdmin
that are available as a download from http://solutions.brother.com/. If you use an older version of
BRAdmin 1 to manage your Brother machines the user authentication will not be secure.
 If you want to avoid access to your machine from older versions of BRAdmin 1, you need to disable the
access from older versions of BRAdmin 1 from Advanced Setting of SNMP on Configure Protocol page
using Web Based Management. (See Secure Management using Web Based Management (web
browser) on page 52.)
 If you use BRAdmin Professional 3 and Web Based Management together, use Web Based Management
with the HTTPS protocol. (See Secure Management using Web Based Management (web browser)
on page 52.)
59
Security features
 If you are managing a mixed group of older print servers 2 and the print servers with BRAdmin
Professional 3, we recommend using a different password in each group. This will ensure security is
maintained on the new print servers.
1
BRAdmin Professional older than Ver. 2.80, Web BRAdmin older than Ver. 1.40, BRAdmin Light for Macintosh older than Ver. 1.10
2
NC-2000 series, NC-2100p, NC-3100h, NC-3100s, NC-4100h, NC-5100h, NC-5200h, NC-6100h, NC-6200h, NC-6300h, NC-6400h, NC-8000,
NC-100h, NC-110h, NC-120w, NC-130h, NC-140w, NC-8100h, NC-9100h, NC-7100w, NC-7200w, NC-2200w
Using Certificates for device security
7
Your Brother machine supports the use of multiple security certificates allowing secure management,
authentication and communication with the machine. The following security certificate features can be used
with the machine.
 SSL/TLS communication
 IEEE 802.1x authentication
 SSL communication for SMTP/POP3
7
The Brother machine supports the following certificates.
 Self-signed certificate
This print server issues its own certificate. Using this certificate, you can easily use the SSL/TLS
communication without having a certificate from a CA. (See Creating and installing a certificate
on page 62.)
 Certificate from a CA
There are two methods for installing a certificate from a CA. If you already have a CA or if you want to use
a certificate from an external trusted CA:
• When using a CSR (Certificate Signing Request) from this print server. (See How to create a CSR
on page 67.)
• When importing a certificate and a private key. (See Import and export the certificate and private key
on page 68.)
 CA certificate
If you use a CA certificate that identifies the CA (Certificate Authority) itself and owns its private key, you
must import a CA certificate from the CA, prior to the configuration. (See Import and export a CA certificate
on page 70.)
Note
• If you are going to use SSL/TLS communication, we recommend that you contact your system
administrator first.
• When you reset the print server back to its default factory settings, the certificate and the private key that
are installed will be deleted. If you want to keep the same certificate and the private key after resetting the
print server, export them before resetting and re-install them. (See How to export the self-signed
certificate, the certificate issued by a CA, and the private key on page 69.)
60
Security features
Configure certificate using Web Based Management
7
This feature can be configured using Web Based Management only. Follow these steps to access the
configure certificate page using Web Based Management.
a
b
Start your web browser.
Type “http://printer’s IP address/” into your browser (where “printer’s IP address” is
the printer’s IP address).
 For example:
http://192.168.1.2/
c
d
Click Network Configuration.
e
f
g
Click OK.
Enter a user name and a password. The default User Name is “admin” and the default Password is
“access”.
7
Click Configure Certificate.
You can configure the certificate settings from the screen below.
Note
• The functions that are grayed and unlinked indicate they are not available.
• For more information on configuration, see the Help text in the Web Based Management.
61
Security features
Creating and installing a certificate
7
Step by step chart for creating and installing a certificate
self-signed certificate
or
7
certificate from a CA
Create a self-signed certificate using Web Based
Management. (See page 62.)
Create a CSR using Web Based Management.
(See page 67.)
Install the self-signed certificate to your computer.
(See page 62.)
Install the certificate issued by CA to your Brother
machine using Web Based Management. (See
page 68.)
You have completed creating and installing the
certificate.
Install the certificate to your computer. (See
page 68.)
7
You have completed creating and installing the
certificate.
How to create and install a self-signed certificate
a
b
7
Click Create Self-Signed Certificate on the Configure Certificate page.
Enter a Common Name and a Valid Date, then click Submit.
Note
• The length of the Common Name is less than 64 bytes. Enter an identifier such as an IP address, node
name or domain name to use when accessing this machine through SSL/TLS communication. The node
name is displayed by default.
• A warning will pop-up if you use the IPPS or HTTPS protocol and enter a different name in the URL than
the Common Name that was used for the self-signed certificate.
c
The self-signed certificate is created and saved in your machine's memory successfully.
To use SSL/TLS communication, the self-signed certificate also needs to be installed on your computer.
Proceed to the next section.
How to install the self-signed certificate on your computer
7
Note
The following steps are for Microsoft® Internet Explorer®. If you use another web browser, follow the help
text of the web browser itself.
62
Security features
For Windows Vista® and Windows® 7 users that have administrator rights
a
b
Click the
7
button and All Programs.
Right-click Internet Explorer, and then click Run as administrator.
7
Note
If the User Account Control screen appears,
(Windows Vista®) Click Continue (Allow).
(Windows® 7) Click Yes.
63
Security features
c
Type “https://printer’s IP address/” into your browser to access your machine (where
“printer’s IP address” is the printer’s IP address or the node name that you assigned for the
certificate).
Then, click Continue to this website (not recommended)..
7
d
Click Certificate Error, and then click View certificates. For the rest of the instructions, follow the steps
from step d in For Windows® 2000/XP and Windows Server® 2003/2008 users on page 65.
64
Security features
For Windows® 2000/XP and Windows Server® 2003/2008 users
a
b
Start your web browser.
c
When the following dialog appears, click View Certificate.
7
Type “https://printer’s IP address/” into your browser to access your machine (where
“printer’s IP address” is the IP address or the node name that you assigned for the certificate).
7
d
Click Install Certificate... from the General tab.
e
When the Certificate Import Wizard appears, click Next.
65
Security features
f
Choose Place all certificates in the following store and then, click Browse....
g
Choose Trusted Root Certification Authorities and then click OK.
7
h
Click Next.
i
Click Finish.
66
Security features
j
Click Yes, if the fingerprint (thumbprint) is correct.
Note
The fingerprint (thumbprint) is printed on the Network Configuration List. (To learn how to print the Network
Configuration List, see Printing the Network Configuration List on page 35.)
k
l
Click OK.
The self-signed certificate is now installed on your computer, and SSL/TLS communication is available.
How to create a CSR
a
b
7
Click Create CSR on the Configure Certificate page.
Enter a Common Name and your information, such as Organization. Then click Submit.
Note
• We recommend that the Root Certificate from the CA be installed on your computer before creating the
CSR.
• The length of the Common Name is less than 64 bytes. Enter an identifier such as an IP address, node
name or domain name to use when accessing this printer through SSL/TLS communication. The node
name is displayed by default. The Common Name is required.
• A warning will pop-up if you enter a different name in the URL than the Common Name that was used for
the certificate.
• The length of the Organization, the Organization Unit, the City/Locality and the State/Province is less
than 64 bytes.
• The Country/Region should be an ISO 3166 country code composed of two characters.
• If you are configuring X.509v3 certificate extension, choose the Configure extended partition check box
and then choose Auto or Manual.
c
When the contents of the CSR appear, click Save to save the CSR file to your computer.
67
7
Security features
d
The CSR is created.
Note
• Follow your CA policy regarding the method to send a CSR to your CA.
• If you are using Enterprise root CA of Windows Server® 2003/2008, we recommend using the Web
Server for the certificate template when creating the Client Certificate for secure management. If you are
creating a Client Certificate for an IEEE 802.1x environment with EAP-TLS authentication, we recommend
using User for the certificate template. For more information, see the SSL communication page from the
top page for your model at http://solutions.brother.com/.
How to install the certificate to your machine
7
When you receive the certificate from a CA, follow the steps below to install it into the print server.
Note
Only a certificate issued with this machine’s CSR can be installed. When you want to create another CSR,
make sure that the certificate is installed before creating another CSR. Create another CSR after installing
the certificate to the machine. Otherwise the CSR you have made before installing will be invalid.
a
b
c
7
Click Install Certificate on the Configure Certificate page.
Specify the file of the certificate that has been issued by a CA, and then click Submit.
Now the certificate is created and saved in your machine memory successfully.
To use SSL/TLS communication, the Root Certificate from the CA needs to be installed on your
computer. Contact your network administrator about installation.
Import and export the certificate and private key
7
You can store the certificate and private key on the machine and manage them by importing and exporting.
How to import the self-signed certificate, the certificate issued by a CA, and the private key
a
b
c
d
7
Click Import Certificate and Private Key on the Configure Certificate page.
Specify the file that you want to import.
Enter the password if the file is encrypted, and then click Submit.
Now the certificate and private key are imported to your machine successfully.
To use SSL/TLS communication, the Root Certificate from the CA needs to also be installed on your
computer. Contact your network administrator about the installation.
68
Security features
How to export the self-signed certificate, the certificate issued by a CA, and the private key
a
b
7
Click Export shown with Certificate List on the Configure Certificate page.
Enter the password if you want to encrypt the file.
Note
If a blank password is used, the output is not encrypted.
c
d
e
Enter the password again for confirmation, and then click Submit.
Specify the location where you want to save the file.
Now the certificate and private key are exported to your computer.
Note
You can import the file that you exported.
7
Managing multiple certificates
7
This multiple certificate feature allows you to manage each certificate that you have installed using Web
Based Management. After installing certificates, you can view what certificates are installed from the
Configure Certificate page and then view each certificate's content, delete or export the certificate. For
information on how to access the Configure Certificate page, see Configure certificate using Web Based
Management on page 61. The Brother machine allows you to store up to three self-signed certificates or up
to four certificates issued by a CA. You can use the stored certificates for using the HTTP/IPPS protocol or
IEEE 802.1x authentication.
You can also store up to four CA certificates for using IEEE 802.1x authentication and SSL for SMTP/POP3.
We recommend you store one certificate less and keep the last free to deal with certificate expiration. For
example, if you want to store a CA certificate, store three certificates and leave one storage as a backup. In
the case of re-issuing the certificate, such as when the certificate is expired, you can import a new certificate
to the backup and then you can delete the expired certificate, to avoid configuration failure.
Note
When you use HTTP/IPPS protocol or IEEE 802.1x, you must choose which certificate you are using.
69
Security features
Import and export a CA certificate
7
You can store a CA certificate and private key on the machine by importing and exporting.
How to import a CA certificate and private key
a
b
Click Configure CA Certificate on the Configure Certificate page.
Click Import CA Certificate. Click Submit.
How to export a CA certificate and private key
a
b
7
7
Click Configure CA Certificate on the Configure Certificate page.
Choose the certificate you want to export and click Export. Click Submit.
7
70
8
Troubleshooting
8
Overview
8
This chapter explains how to resolve typical network problems you may encounter when using Brother
machine. If, after reading this chapter, you are unable to resolve your problem, please visit the Brother
Solutions Center at: http://solutions.brother.com/.
Please go to the Brother Solutions Center at http://solutions.brother.com/ and click Manuals on your model
page to download the other manuals.
Identifying your problem
8
Make sure that the following items are configured before reading this chapter.
First check the following:
The power cord is connected properly and the Brother machine is turned on.
The access point (for wireless), router or hub are turned on and its link button is blinking.
All protective packaging has been removed from the machine.
8
The toner cartridges and drum unit are installed properly.
The front and back covers are fully closed.
Paper is inserted properly in the paper tray.
(For wired networks) A network cable is securely connected to the Brother machine and the router or hub.
Go to the page for your solution from the lists below
8
 I cannot complete the wireless network setup configuration. (See page 72.)
 The Brother machine is not found on the network during the printer driver installation. (See page 72.)
 The Brother machine cannot print over the network. (See page 73.)
 The Brother machine is not found on the network even after successful installation. (See page 73.)
 I'm using security software. (See page 75.)
 I want to check my network devices are working properly. (See page 76.)
71
Troubleshooting
I cannot complete the wireless network setup configuration.
Question
Interface Solution
Is your security settings
(SSID/Network Key)
correct?
wireless
 Reconfirm and choose the correct security settings.
• The manufacturer's name or model no. of the WLAN access
point/router may be used as the default security settings.
• See the instructions supplied with your WLAN access point/router for
information on how to find the security settings.
• Ask the manufacturer of your WLAN access point/router or ask your
Internet provider or network administrator.
 For information on what the SSID and Network Key are, see SSID,
Network Key and channels in the Network Glossary.
Are you using MAC address
filtering?
wireless
Is your WLAN access
point/router in a stealth
mode? (not broadcasting
the SSID)
wireless
I have checked and tried all
of the above, but still cannot
complete the wireless
configuration. Is there
anything else I can do?
wireless
Confirm the MAC address of the Brother machine is allowed in the filter. You
can find the MAC address from Brother machine's control panel. (See
Function table and default factory settings on page 37.)
 You should type the correct SSID name or Network Key by hand.
 Check the SSID name or the Network Key in the instructions supplied
with your WLAN access point/router and reconfigure the wireless
network setup. (For more information, see Configuring your machine
when the SSID is not broadcast on page 17.)
8
Use the Network Connection Repair Tool. See Brother machine cannot print
over the network. Brother machine is not found on the network even after the
successful installation. on page 73.
Brother machine is not found on the network during the printer driver installation.
Question
Interface Solution
Are you using security
software?
wired/
wireless
 Choose to search for Brother machine again on the installer dialog.
 Allow access when the alert message of the security software appears
during the printer driver installation.
 For more information about security software, see I'm using security
software. on page 75.
Is your Brother machine
placed too far from the
WLAN access point/router?
wireless
Place your Brother machine within about 3.3 feet (1 meter) from the WLAN
access point/router when you configure the wireless network settings.
Are there any obstructions
(walls or furniture, for
example) between your
machine and the WLAN
access point/router?
wireless
Move your Brother machine to an obstruction-free area, or closer to the
WLAN access point/router.
72
Troubleshooting
Brother machine is not found on the network during the printer driver installation. (continued)
Question
Interface Solution
Is there a wireless
computer, Bluetooth
supported device,
microwave oven or digital
cordless phone near the
Brother machine or the
WLAN access point/router?
wireless
Move all the devices away from Brother machine or WLAN access
point/router.
Brother machine cannot print over the network.
Brother machine is not found on the network even after the successful installation.
Question
Interface Solution
Are you using security
software?
wired/
wireless
Is your Brother machine
assigned with an available
IP address?
wired/
wireless
See I'm using security software. on page 75.
 Confirm the IP address and the Subnet Mask
Verify that both the IP addresses and Subnet Masks of your computer
and the Brother machine are correct and located on the same network.
For more information on how to verify the IP address and the Subnet
Mask, ask the network administrator or visit the Brother Solutions Center
at http://solutions.brother.com/.
 (Windows®)
Confirm the IP address and the Subnet Mask using the Network
Connection Repair Tool.
Use the Network Connection Repair Tool to fix the Brother machine's
network settings. It will assign the correct IP address and the Subnet
Mask.
To use the Network Connection Repair Tool, ask the network
administrator for the details and then follow the steps below:
Note
• (Windows® 2000 Professional/XP/XP Professional x64 Edition/Windows
Vista®/Windows® 7) You must log on with Administrator rights.
• Make sure that the Brother machine is turned on and is
network-connected to your computer.
73
8
Troubleshooting
Brother machine cannot print over the network.
Brother machine is not found on the network even after the successful installation. (continued)
Question
Interface Solution
Is your Brother machine
assigned with an available
IP address?
wired/
wireless
(continued)
1 (Windows® 2000/XP, Windows Server® 2003/2008)
Click the Start button, All Programs (Programs for Windows® 2000),
Accessories and Windows Explorer, and then My computer.
(Windows Vista®/Windows® 7)
Click the
button and Computer.
2 Double-click Local Disk (C:), Program Files or Program Files (x86)
for 64-bit OS users, Browny02, Brother, BrotherNetTool.exe to run the
program.
Note
If the User Account Control screen appears,
(Windows Vista®) Click Continue.
(Windows® 7) Click Yes.
3 Follow the on screen instructions.
8
4 Check the diagnosis by printing the Network Configuration List.
Note
The Network Connection Repair Tool will start automatically if you check
Enable Network Connection Repair Tool from the Options tab on
Status Monitor. This is not recommended when your network
administrator has set the IP address to static, since it will automatically
changes the IP address.
If the correct IP address and the Subnet mask are still not assigned even
after using the Network Connection Repair Tool, ask the network
administrator for this information, or visit the Brother Solutions Center at
http://solutions.brother.com/.
74
Troubleshooting
Brother machine cannot print over the network.
Brother machine is not found on the network even after the successful installation. (continued)
Question
Interface Solution
Did your previous printing
job fail?
wired/
wireless
 If the failed printing job is still in the print queue of your computer, delete
it.
 Double-click the printer icon in the following folder and then choose the
Cancel All Documents in the Printer menu:
(Windows® 2000)
Start, Settings and then Printers.
(Windows® XP)
Start and Printers and Faxes.
(Windows Vista®)
, Control Panel, Hardware and Sound and then Printers.
(Windows® 7)
, Control Panel, Devices and Printers and then Printers and
Faxes.
Are you connecting the
Brother machine to the
network using wireless
capabilities?
wireless
8
 Print the WLAN report for confirm the state of the wireless connection.
(For how to print, see Printing the WLAN report (For HL-4570CDW(T))
on page 36.)
If there is an error code on the printed WLAN report, see Troubleshooting
in the Quick Setup Guide.
 See Brother machine is not found on the network during the printer driver
installation. on page 72.
I have checked and tried all
of above, however the
Brother machine does not
print. Is there anything else I
can do?
wired/
wireless
Uninstall the printer driver and reinstall it.
I'm using security software.
Question
Interface Solution
Did you choose to accept
the security alert dialog
during the printer driver
installation, applications'
start-up process or when
using the printing features?
wired/
wireless
If you did not choose to accept the security alert dialog, the firewall function
of your security software may be rejecting access. Some security software
might block access without showing a security alert dialog. To allow access,
see the instructions of your security software or ask the manufacturer.
I want to know the
necessary port number for
the security software
settings.
wired/
wireless
The following port numbers are used for Brother network features:
 Network printing i Port number 137 / Protocol UDP
 BRAdmin Light i Port number 161 / Protocol UDP
For details on how to open the port, see the instructions of the security
software or ask the manufacturer.
75
Troubleshooting
I want to check my network devices are working properly.
Question
Interface Solution
Is your Brother machine,
access point/router or
network hub turned on?
wired/
wireless
Make sure you have confirmed all instructions in First check the following:
on page 71.
Where can I find Brother
machine's network settings,
such as IP address?
wired/
wireless
Print the Network Configuration List. See Printing the Network Configuration
List on page 35.
How can I check the link
status of Brother machine?
wired/
wireless
Print the Network Configuration List and check that Ethernet Link Status or
Wireless Link Status is Link OK.
If the Link Status shows Link Down or Failed to Associate, start over
again from the First check the following: on page 71.
Can you “ping” Brother
machine from your
computer?
wired/
wireless
Ping the Brother machine from your computer using the IP address or the
node name.
 Successful i Your Brother machine is working correctly and connected
to the same network as your computer.
 Unsuccessful i Your Brother machine is not connected to the same
network as your computer.
(Windows®)
Ask the network administrator and use the Network Connection Repair
Tool to fix the IP address and the subnet mask automatically. For the
detail of the Network Connection Repair Tool, see (Windows®) Confirm
the IP address and the Subnet Mask using the Network Connection
Repair Tool. in Is your Brother machine assigned with an available IP
address? on page 73.
(Macintosh)
Confirm the IP address and the Subnet Mask are set correctly. See
Confirm the IP address and the Subnet Mask in Is your Brother machine
assigned with an available IP address? on page 73.
Is the Brother machine
connecting to the wireless
network?
wireless
Print the WLAN report for confirm the state of the wireless connection. (For
how to print, see Printing the WLAN report (For HL-4570CDW(T))
on page 36. If there is an error code on the printed WLAN report see
Troubleshooting in the Quick Setup Guide.
I have checked and tried all
of the above, however, I'm
still having problems. Is
there anything else I can
do?
wired/
wireless
See the instructions supplied with your WLAN access point/router to find the
SSID and the Network Key information and set them correctly. For details of
the SSID and the Network Key, See Is your security settings (SSID/Network
Key) correct? in I cannot complete the wireless network setup configuration.
on page 72.
76
8
A
Appendix A
A
Supported protocols and security features
Interface
Ethernet
Wireless
Network
(common)
Network
(Security)
Network
(Wireless) 1
1
A
10/100BASE-TX
1
IEEE802.11b/g (Infrastructure Mode / Ad-hoc Mode)
Protocol (IPv4)
ARP, RARP, BOOTP, DHCP, APIPA (Auto IP), WINS/NetBIOS name
resolution, DNS Resolver, mDNS, LLMNR responder, LPR/LPD,
Custom Raw Port/Port9100, IPP/IPPS, FTP Server, TELNET Server,
HTTP/HTTPS server, TFTP client and server, SMTP Client,
SNMPv1/v2c/v3, ICMP, LLTD responder, Web Services (Print), CIFS
client, SNTP client
Protocol (IPv6)
NDP, RA, DNS resolver, mDNS, LLMNR responder, LPR/LPD,
Custom Raw Port/Port9100, IPP/IPPS, FTP Server, TELNET Server,
HTTP/HTTPS server, TFTP client and server, SMTP Client,
SNMPv1/v2c/v3, ICMPv6, LLTD responder, Web Services (Print),
CIFS Client, SNTP Client
Wired
APOP, POP before SMTP, SMTP-AUTH, SSL/TLS (IPPS, HTTPS,
SMTP, POP), SNMP v3, 802.1x (EAP-MD5, EAP-FAST, PEAP,
EAP-TLS, EAP-TTLS), Kerberos
Wireless 1
WEP 64/128 bit, WPA-PSK (TKIP/AES), WPA2-PSK (AES), APOP,
POP before SMTP, SMTP-AUTH, SSL/TLS (IPPS, HTTPS, SMTP,
POP), SNMP v3, 802.1x (LEAP, EAP-FAST, PEAP, EAP-TLS,
EAP-TTLS), Kerberos
Wireless
Certification
Wi-Fi Certification Mark License, Wi-Fi Protected Setup (WPS)
Identifier Mark License, AOSS Logo
A
For HL-4570CDW(T)
77
B
Index
A
M
Ad-hoc mode .......................................................10, 11
AOSS™ ................................................. 12, 13, 16, 33
APIPA ....................................................................... 32
MAC Address ........................................ 4, 5, 6, 34, 35
B
Network Configuration List ........................................ 35
Network Connection Repair Tool .............................. 73
BRAdmin Light ........................................................1, 3
BRAdmin Professional 3 .................................. 1, 6, 59
Brother installer application .................................12, 13
Brother Solutions Center .........................................4, 6
BRPrint Auditor ........................................................... 7
C
N
O
Operating systems ...................................................... 1
P
Certificate .................................................................. 60
Control Panel .............................................................. 3
PBC ........................................................ 12, 13, 16, 33
PIN Method .................................................. 15, 24, 33
POP before SMTP .................................................... 55
D
R
Driver Deployment Wizard .......................................... 1
Reset the network settings ........................................ 35
E
S
Ethernet .................................................................... 33
SMTP-AUTH ............................................................. 55
SNMPv3 .................................................................... 52
Specifications ............................................................ 77
SSL/TLS .................................................................... 60
Status Monitor ............................................................. 1
Subnet mask ............................................................. 32
F
Factory default .......................................................... 35
G
Gateway .................................................................... 32
H
HTTPS ...................................................................... 52
Hyper Text Transfer Protocol ...................................... 6
T
TCP/IP ................................................... 31, 37, 38, 39
V
Vertical Pairing ............................................................ 1
I
W
IEEE 802.1x ................................................. 16, 26, 27
Infrastructure mode ...............................................9, 11
IP address ................................................................. 32
IP Boot Tries ............................................................. 32
IPPS .......................................................................... 54
IPv6 ........................................................................... 32
Web BRAdmin ........................................................1, 7
Web browser (HTTP) .................................................. 6
Web Based Management (web browser) ......... 1, 6, 52
Wi-Fi Protected Setup ..................... 12, 13, 16, 24, 33
Wireless network ......................................................... 8
WLAN ........................................................................ 39
WLAN report ................................................ 36, 75, 76
78
B
Download PDF