Alpine | CDE-9848RB | Owner`s manual | Alpine CDE-9848RB Owner`s manual

FOR CAR USE ONLY/NUR FÜR AUTOMOBIL GEBRAUCH/POUR APPLICATION AUTOMOBILE UNIQUEMENT/
PARA USO EN AUTOMÓVILES/SOLO PER L’UTILIZZO IN AUTOMOBILE/ENDAST FÖR BILBRUK
R
EN
RDS MP3 CD Receiver
CDE-9848RB/CDE-9846R/
CDE-9846RM
DE
FR
• OWNER’S MANUAL
Please read before using this equipment.
• BEDIENUNGSANLEITUNG
Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch des Gerätes.
• MODE D’EMPLOI
Veuillez lire avant d’utiliser cet appareil.
ES
• MANUAL DE OPERACIÓN
Léalo antes de utilizar este equipo.
• ISTRUZIONI PER L’USO
Si prega di leggere prima di utilizzare il attrezzatura.
• ANVÄNDARHANDLEDNING
Innan du använder utrustningen bör du läsa igenom denna användarhandledning.
ALPINE ELECTRONICS MARKETING, INC.
1-1-8 Nishi Gotanda,
Shinagawa-ku,
Tokyo 141-0031, Japan
Phone 03-5496-8231
ALPINE ELECTRONICS OF AMERICA, INC.
19145 Gramercy Place, Torrance,
California 90501, U.S.A.
Phone 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS OF CANADA, INC.
777 Supertest Road, Toronto,
Ontario M3J 2M9, Canada
Phone 1-800-ALPINE-1 (1-800-257-4631)
Dalian Dongtai Colour Printing Technology Co., Ltd.
No.24 Liaohexisan Road, Dalian Economic&Technical
Development Zone, China
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.
161-165 Princes Highway, Hallam
Victoria 3803, Australia
Phone 03-8787-1200
ALPINE ITALIA S.p.A.
Viale C. Colombo 8, 20090 Trezzano
Sul Naviglio (MI), Italy
Phone 02-484781
ALPINE ELECTRONICS GmbH
Frankfurter Ring 117, 80807 München, Germany
Phone 089-32 42 640
ALPINE ELECTRONICS DE ESPAÑA, S.A.
Portal de Gamarra 36, Pabellón, 32
01013 Vitoria (Alava)-APDO 133, Spain
Phone 945-283588
ALPINE ELECTRONICS OF U.K. LTD.
Alpine House
Fletchamstead Highway, Coventry CV4 9TW, U.K.
Phone 0870-33 33 763
ALPINE ELECTRONICS FRANCE S.A.R.L.
(RCS PONTOISE B 338 101 280)
98, Rue de la Belle Etoile, Z.I. Paris Nord Il,
B.P. 50016, 95945 Roissy Charles de Gaulle
Cedex, France
Phone 01-48638989
ALPINE ELECTRONICS (BENELUX) GmbH
Leuvensesteenweg 510-B6,
1930 Zaventem, Belgium
Phone 02-725-13 15
Designed by ALPINE Japan
Printed in China (Y)
68-04123Z33-A
IT
SE
ENGLISH
Contents
Operating Instructions
WARNING
WARNING .................................................. 2
CAUTION ................................................... 2
PRECAUTIONS ......................................... 2
Getting Started
Turning Power On and Off ............................... 5
Detaching and Attaching the Front Panel ......... 5
Initial System Start-Up ..................................... 5
Adjusting Volume ............................................. 5
Radio
Listening to Radio ............................................. 6
Manual Storing of Station Presets .................... 6
Automatic Memory of Station Presets .............. 6
Tuning to Preset Stations .................................. 6
RDS
Setting RDS Reception Mode and Receiving
RDS Stations ................................................. 7
Recalling Preset RDS Stations .......................... 7
Receiving RDS Regional (Local) Stations ....... 7
PI SEEK Setting ................................................ 8
Receiving Traffic Information .......................... 8
PTY (Programme Type) Tuning ....................... 8
Receiving Traffic Information While Playing
CD or Radio ................................................... 9
Priority News .................................................... 9
Displaying Radio Text ...................................... 9
CD/MP3
Playback .......................................................... 10
Repeat Play ..................................................... 11
M.I.X. (Random Play) .................................... 11
Scanning Programmes .................................... 11
Searching from CD Text ................................. 11
File/Folder Name Search (concerning MP3) .... 11
Quick Search (CDE-9848RB only) .................. 12
About MP3 ...................................................... 12
Sound Setting
Adjusting Bass/Treble/Balance (Between Left
and Right)/Fader (Between Front and Rear)/
Defeat .......................................................... 13
Setting the Bass Control ................................. 14
Setting the Treble Control ............................... 14
Turning Loudness On/Off ............................... 14
Other Functions
Displaying the Title/Text ................................. 15
Titling Discs .................................................... 16
Erasing Disc Title ............................................ 16
SETUP
Sound Customizing
Adjusting Source Signal Levels ...................... 17
Subwoofer On and Off .................................... 17
Visual Customizing
Dimmer Control (CDE-9848RB only) ........... 17
Scroll Setting ................................................... 17
Scroll Type Setting .......................................... 17
MP3
Playing MP3 Data ........................................... 17
External Device
Setting the AUX Mode
(CDE-9848RB only) .................................... 17
Connecting to an External Amplifier .............. 17
Information
In Case of Difficulty ....................................... 18
Specifications .................................................. 19
Installation and Connections
Warning ........................................................... 20
Caution ............................................................ 20
Precautions ...................................................... 20
Installation ...................................................... 21
Connections ...................................................... 22
1-EN
Operating Instructions
WARNING
WARNING
This symbol means important instructions. Failure
to heed them can result in serious injury or death.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR
ATTENTION AWAY FROM SAFELY DRIVING YOUR
VEHICLE.
Any function that requires your prolonged attention should only
be performed after coming to a complete stop. Always stop the
vehicle in a safe location before performing these functions.
Failure to do so may result in an accident.
CAUTION
This symbol means important instructions. Failure
to heed them can result in injury or material
property damage.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage to the
product. Return it to your authorized Alpine dealer or the nearest
Alpine Service Centre for repairing.
PRECAUTIONS
Product Cleaning
Failure to do so may result in an accident.
Use a soft dry cloth for periodic cleaning of the product. For
more severe stains, please dampen the cloth with water only.
Anything else has the chance of dissolving the paint or damaging
the plastic.
DO NOT DISASSEMBLE OR ALTER.
Temperature
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL
HEAR OUTSIDE NOISE WHILE DRIVING.
Doing so may result in an accident, fire or electric shock.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may
result in fire, etc.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE
REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed,
consult a physician immediately.
USE THE CORRECT AMPERE RATING WHEN REPLACING
FUSES.
Be sure the temperature inside the vehicle is between +60°C
(+140°F) and –10°C (+14°F) before turning your unit on.
Moisture Condensation
You may notice the CD playback sound wavering due to
condensation. If this happens, remove the disc from the player
and wait about an hour for the moisture to evaporate.
Damaged Disc
Do not attempt to play cracked, warped, or damaged discs.
Playing a bad disc could severely damage the playback
mechanism.
Failure to do so may result in fire or electric shock.
Maintenance
DO NOT BLOCK VENTS OR RADIATOR PANELS.
If you have problems, do not attempt to repair the unit yourself.
Return it to your Alpine dealer or the nearest Alpine Service
Station for servicing.
Doing so may cause heat to build up inside and may result in fire.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in fire,
electric shock or other injury.
DO NOT PLACE HANDS, FINGERS OR FOREIGN OBJECTS
IN INSERTION SLOTS OR GAPS.
Doing so may result in personal injury or damage to the product.
2-EN
Correct Handling
PRECAUTIONS
Do not drop the disc while handling. Hold the disc so you will
not leave fingerprints on the surface. Do not affix tape, paper, or
gummed labels to the disc. Do not write on the disc.
Never Attempt the Following
Do not grip or pull out the disc while it is being pulled back into
the player by the automatic reloading mechanism.
Do not attempt to insert a disc into the unit when the unit power
is off.
CORRECT
INCORRECT
Inserting Discs
Your player accepts only one disc at a time for playback. Do not
attempt to load more than one disc.
Make sure the label side is facing up when you insert the disc.
“ERROR” will be displayed on your player if you insert a disc
incorrectly. If “ERROR” continues to be displayed even though
the disc has been inserted correctly, push the RESET switch with
a pointed object such as a ballpoint pen.
Playing a disc while driving on a very bumpy road may result in
skips, but this will not scratch the disc or damage the player.
CORRECT
Disc Cleaning
Fingerprints, dust, or soil on the surface of the disc could cause
the CD player to skip. For routine cleaning, wipe the playing
surface with a clean, soft cloth from the centre of the disc to the
outer edge. If the surface is heavily soiled, dampen a clean, soft
cloth in a solution of mild neutral detergent before cleaning the
disc.
New Discs
As a protective measure to prevent the CD from jamming,
“ERROR” will be displayed if discs with irregular surface are
inserted or inserted incorrectly. When a new disc is inserted into
the player and ejected after initial loading, using your finger, feel
around the inside of the centre hole and outside edge of the disc.
If you feel any small bumps or irregularities, this could inhibit
proper loading of the disc. To remove the bumps, rub the inside
edge of the hole and outside edge of the disc with a ballpoint pen
or other such instrument, then insert the disc again.
Centre Hole
Bumps
Centre Hole
Disc Accessories
There are various accessories available on the market for
protecting the disc surface and improving sound quality.
However, most of them will influence the thickness and/or
diameter of the disc. Using such accessories can cause the disc to
be out of standard specifications and may create operational
problems. We recommend not using these accessories on discs
played in Alpine CD players.
New
Disc
Outside
(Bumps)
Transparent Sheet
Disc Stabilizer
Irregular Shaped Discs
Be sure to use round shape discs only for this unit and never use
any special shape discs.
Use of special shape discs may cause damage to the mechanism.
Continued
Installation Location
Make sure the CDE-9848RB/CDE-9846R/CDE-9846RM will not
be installed in a location subjected to:
•
•
•
•
Direct sun and heat
High humidity and water
Excessive dust
Excessive vibrations
3-EN
On handling Compact Discs (CD/CD-R/CD-RW)
•
•
•
•
•
•
Do not touch the surface.
Do not expose the disc to direct sunlight.
Do not affix stickers or labels.
Clean the disc when it is dusty.
Make sure that there are no bumps around the disc.
Do not use commercially available disc accessories.
Do not leave the disc in the car or the unit for a long
time. Never expose the disc to direct sunlight. Heat
and humidity may damage the CD and you may not be
able to play it again.
To customers using CD-R/CD-RW
•
•
If a CD-R/CD-RW cannot be played back, make sure the last
recording session was closed (finalized).
Finalize the CD-R/CD-RW if necessary, and attempt playback
again.
About media that can be played.
Use only compact discs with the label side showing the CD logo
marks below.
If you use unspecified compact discs, correct performance cannot
be guaranteed.
You can play CD-Rs (CD-Recordable)/CD-RWs (CDReWritable) which have been recorded only on audio devices.
You can also play CD-Rs/CD-RWs containing MP3 formatted
audio files.
•
•
Some of the following CDs may not play on this unit:
Flawed CDs, CDs with fingerprints, CDs exposed to extreme
temperatures or sunlight (e.g., left in the car or this unit), CDs
recorded under unstable conditions, CDs on which a
recording failed or a re-recording was attempted, copyprotected CDs which do not conform to the audio CD
industry standard.
Use discs with MP3 files written in a format compatible with
this unit. For details, see pages 12-13.
• “MPEG Layer-3 audio coding technology licensed from
Fraunhofer llS and Thomson”
• “Supply of this product only conveys a license for private, noncommercial use and does not convey a license nor imply any right
to use this product in any commercial (i.e. revenue-generation)
real time broadcasting (terrestrial, satellite, cable and/or any
other media), broadcasting/streaming via internet, intranets and/
or other networks or in other electronic content distribution
systems, such as pay-audio or audio-on-demand applications. An
independent license for such use is required. For details, please
visit http://www. mp3licensing.com.”
4-EN
Getting Started
CDE-9848RB
Attaching
1
2
Rotary encoder
Insert the right side of the front panel into the main
unit. Align the groove on the front panel with the
projections on the main unit.
Push the left side of the front panel until it locks
firmly into the main unit.
SOURCE/POWER
2
1
CDE-9846R/CDE-9846RM
4
• Before attaching the front panel, make sure that there is no dirt or
dust on the connector terminals and no foreign object between the
front panel and the main unit.
• Attach the front panel carefully, holding the sides of the front panel
to avoid pushing buttons by mistake.
Initial System Start-Up
SOURCE/POWER
Be sure to press the RESET switch when using the unit for the first
time, after changing the car battery, etc.
1
2
3
Turn off the unit power.
Remove the detachable front panel.
Press RESET with a ballpoint pen or similar
pointed object.
3
1
Turning Power On and Off
RESET switch
Press SOURCE/POWER to turn on the unit.
• The unit can be turned on by pressing any other button except eject
c.
Adjusting Volume
Press and hold SOURCE/POWER for at least 2
seconds to turn off the unit.
Turn the Rotary encoder (CDE-9848RB only) or press
4 and 3 (CDE-9846R/CDE-9846RM only) until the
desired sound is obtained.
• The first time power is turned on, the volume will start from level 12.
Detaching and Attaching the Front Panel
Detaching
1
2
3
Connectable to Steering Remote Control Interface Box
You can operate this unit from the vehicle's control unit when an
Alpine Steering Remote Control Interface Box (optional) is
connected. For details, contact your Alpine dealer.
Turn off the unit power.
Press
(Release) at the lower left side until the
front panel pops out.
Grasp the left side of the front panel and pull it out.
• The front panel may become hot in normal usage (especially the
connector terminals on the back of the front panel). This is not a
malfunction.
• To protect the front panel, place it in the supplied carrying case.
5-EN
Radio
Manual Storing of Station Presets
1
CDE-9848RB
2
TUNE/A.ME
SOURCE/POWER
BAND
Select the radio band and tune in a desired radio
station you wish to store in the preset memory.
Press and hold, for at least 2 seconds, any one of
the preset buttons (1 through 6) that you want
to store the station on.
The selected station is stored.
The display shows the band, preset number and station
frequency memorized.
g f
FUNC./SETUP
Preset buttons
(1 through 6)
Automatic Memory of Station Presets
CDE-9846R/CDE-9846RM
TUNE/A.ME
SOURCE/POWER
• A total of 30 stations can be stored in the preset memory (6 stations
for each band: FM1, FM2, FM3, MW and LW).
• If you store a station in a preset memory which already has a
station, the current station will be cleared and replaced with the
new station.
• If the “F” indicator is illuminated, turn off the indicator by
pressing FUNC./SETUP, then you can perform the operation.
1
BAND
2
gf
FUNC./SETUP
Preset buttons
(1 through 6)
Press BAND repeatedly until the desired radio
band is displayed.
Press and hold TUNE/A.ME for at least 2 seconds.
The frequency on the display continues to change while
the automatic memory is in progress. The tuner will
automatically seek and store 6 strong stations in the
selected band. They will be stored into buttons 1 to 6 in
order of signal strength.
When the automatic memory has been completed, the
tuner goes to the station stored in preset location No.1.
• If no stations are stored, the tuner will return to the original station
you were listening to before the auto memory procedure began.
Listening to Radio
Tuning to Preset Stations
1
Press SOURCE/POWER until a radio frequency
appears in the display.
1
Press BAND repeatedly until the desired radio
band is displayed.
2
2
3
F1 (FM1) → F2 (FM2) → F3 (FM3) → MW → LW → F1 (FM1)
Press any one of the station preset buttons (1
through 6) that has your desired radio station in
memory.
Press TUNE/A.ME to select the tuning mode.
The display shows the band, preset number and
frequency of the station selected.
DX SEEK (Distance mode) → SEEK (Local mode) →
OFF (Manual mode) → DX SEEK
• The initial mode is Distance mode.
Distance mode:
Both strong and weak stations will be automatically tuned in
(Automatic Seek Tuning).
Local mode:
Only strong stations will be automatically tuned in (Automatic
Seek Tuning).
Manual mode:
The frequency is manually tuned in steps (Manual tuning).
4
Press BAND repeatedly until the desired band is
displayed.
Press g or f to tune in the desired station.
Holding down g or f will change the frequency
continuously.
• The ST indicator appears on the display when a stereo FM station
is tuned in.
6-EN
• If the “F” indicator is illuminated, turn off the indicator by
pressing FUNC./SETUP, then you can perform the operation.
RDS
Recalling Preset RDS Stations
1
CDE-9848RB
g
BAND
2
3
f
4
/PTY TITLE
5
BAND
Press FUNC./SETUP to activate the normal mode.
The “F” indicator goes out.
Make sure that the “F” indicator light goes out, then
press the preset button in which your desired RDS
station is preset.
If the preset station and the stations in the AF list
cannot be received:
When the PI SEEK setting is on (refer to “PI SEEK Setting”
on page 8), the unit searches again for a station in the PI
(Programme Identification) list.
If there are still no stations receivable in the area, the unit
displays the frequency of the preset station and the preset
no. disappears.
If the signal level of the Regional (Local) station being
tuned becomes too weak to receive, press the same
preset button to tune in a Regional station in other district.
CDE-9846R/CDE-9846RM
g
Press 19/AF to activate the RDS mode.
If the preset station’s signal is weak, the unit automatically
searches and tunes to a stronger station in the AF
(Alternative Frequencies) list.
TA
FUNC./SETUP 19/AF 82/NEWS 3
Press FUNC./SETUP so that the “F” indicator
lights up.
f
• For presetting the RDS stations, refer to the Radio Operation
section. The RDS stations can be preset in the F1, F2 and F3 bands
only.
TA
FUNC./SETUP
19/AF 82/NEWS 3
/PTY TITLE
Receiving RDS Regional (Local) Stations
Setting RDS Reception Mode and Receiving
RDS Stations
The RDS (Radio Data System) is a radio information system using
the 57 kHz subcarrier of regular FM broadcast. The RDS allows you
to receive a variety of information such as traffic information, station
names, and to automatically re-tune to a stronger transmitter that is
broadcasting the same programme.
1
2
3
4
5
Press FUNC./SETUP so that the “F” indicator
lights up.
Press 19/AF to activate the RDS mode.
1
2
3
Press and hold FUNC./SETUP for at least 2
seconds to activate the setting mode.
Press g or f to select “REG”.
Press BAND to toggle the mode between
“ON” and “OFF.”
In the REG OFF mode, the unit automatically keeps
receiving the related local RDS station.
4
Press FUNC./SETUP to deactivate the setting
mode.
• Operate the unit while the “F” indicator lights up. If no operation
is performed within 10 seconds, the “F” indicator goes out.
Press g or f to tune in the desired RDS
station.
Press 19/AF again to deactivate the RDS mode.
Press FUNC./SETUP to activate the normal mode.
The “F” indicator goes out.
The RDS digital data includes the following:
PI
Programme Identification
PS
Programme Service Name
AF
List of Alternative Frequencies
TP
Traffic Programme
TA
Traffic Announcement
PTY
Programme Type
EON
Enhanced Other Networks
7-EN
PI SEEK Setting
PTY (Programme Type) Tuning
1
1
2
3
4
Press and hold FUNC./SETUP for at least 2
seconds.
Press g or f to select “PISK.”
Press BAND to toggle the mode between
“ON” and “OFF.”
Press TA so that the “TA” indicator lights up.
Press g or f to select your desired traffic
information station.
When a traffic information station is tuned in, the “TP”
indicator lights up.
Traffic information is heard only when it is being
broadcast. If traffic information is not being broadcast, the
unit is set in the standby mode. When a traffic information
broadcast begins, the unit automatically receives it and
the display shows “TRF-INFO” for a few seconds and
returns to the PS display.
When the traffic information broadcast is over, the unit will
automatically set in the standby mode.
• If the traffic information broadcast signal falls below a certain
level, the unit remains in the receiving mode for 1 minute. If the
signal remains below a certain level for over 1 minute, the “TA”
indicator blinks.
• If you do not want to listen to the traffic information being
received, lightly press TA to skip that traffic information message.
The TA mode will remain in the ON position to receive the next
traffic information message.
• If the volume level is changed while receiving traffic information,
the changed volume level will be memorized. When traffic
information is received next time, the volume level will be
automatically adjusted to the level memorized.
• In the TA mode, the SEEK tuning selects only the TP stations.
8-EN
Press 3
/PTY to activate the PTY mode, while
the unit is in Radio (FM receiving) mode.
The Programme Type of the station being currently received
will be displayed for 10 seconds.
If there is no receivable PTY broadcast, “NO PTY” will be
displayed for 10 seconds.
If no RDS station can be received, the display shows “NO
PTY.”
Press FUNC./SETUP to set the selected mode.
Receiving Traffic Information
1
2
2
Press FUNC./SETUP so that the “F” indicator
lights up.
• If no operation is performed within 10 seconds after pressing
3 /PTY, the PTY mode will be automatically cancelled.
3
Press g or f within 10 seconds after
activating the PTY mode to choose the desired
programme type while the PTY (programme type)
is being displayed.
Each press scrolls the programme type by one.
LIGHT M ↔ CLASSICS ↔ OTHER M
4
Press 3
/PTY within 10 seconds after selecting
the programme type to start searching for a station
in the selected programme type.
The chosen programme type display blinks during
searching and lights when a station is found.
If no PTY station is found, “NO PTY” will be displayed for
10 seconds.
5
Press FUNC./SETUP to activate the normal mode.
The “F” indicator goes out.
• Operate the unit while the “F” indicator lights up. If no operation
is performed within 10 seconds, the “F” indicator goes out.
Receiving Traffic Information While Playing
CD or Radio
1
2
Press TA so that the “TA” indicator lights up.
Press g or f to select a traffic information
station if necessary.
When a traffic information broadcast starts, the unit
automatically mutes the CD player or the regular FM
broadcast.
When the traffic information broadcast finishes, the unit
automatically returns to the original source play before the
traffic information broadcast began.
Priority News
This function allows you to preset to give priority to the News
programme. You will never miss the News programme as the unit
automatically gives priority to the News programme whenever it
begins broadcasting, and interrupts the programme you are currently
listening. This feature is functional when your unit is set to a mode
other than the LW and MW modes.
1
2
In the CD mode:
When the TP signal can no longer be received, the traffic
information station of another frequency will be selected
automatically.
Press 82/NEWS to activate the PRIORITY NEWS
mode.
The “NEWS” indicator appears in the display.
To disable the PRIORITY NEWS function, press
82/NEWS.
When traffic information stations cannot be received:
In the tuner mode:
When the TP signal can no longer be received for over 1
minute, the “TA” indicator blinks.
Press FUNC./SETUP so that the “F” indicator
lights up while the unit is in Radio (FM receiving)
mode.
• In the PRIORITY NEWS function, unlike in the TA function, the
volume does not increase automatically.
3
Press FUNC./SETUP to activate the normal mode.
The “F” indicator light goes out.
• The receiver is equipped with the EON (Enhanced Other
Networks) function in order to keep track of additional alternate
frequencies to the AF list. The “EON” indicator lights up while an
RDS EON station is being received. If the station being received
does not broadcast the traffic information, the receiver
automatically tunes in the related station that broadcasts the traffic
information when it occurs.
• Operate the unit while the “F” indicator lights up. If no operation
is performed within 10 seconds, the “F” indicator goes out.
3
Press TA to deactivate the Traffic Information
mode.
Press TITLE while receiving FM in the radio mode to
select the Radio Text display.
The “TA” indicator goes out.
The display will change every time the button is pressed.
Displaying Radio Text
Text messages from a radio station can be displayed.
PS (Programme Service Name) → Radio Text → FREQUENCY
→ PS (Programme Service Name)
The display shows “WAITING” for a few seconds, then starts
scrolling the text message.
• If there is no receivable text message or the unit cannot receive a
text message properly, the display shows “NO TEXT.”
9-EN
CD/MP3
3
Press g or f to select the desired track (file).
Returning to the beginning of the current track (file):
Press g.
CDE-9848RB
Rotary
encoder
-/J
SOURCE/
POWER
TITLE
c
Fast backward:
Press and hold g.
Advancing to the beginning of the next track (file):
Press f.
Fast forward:
Press and hold f.
g
f
82/NEWS
3 /PTY
19/AF
4 5
6
CDE-9846R/CDE-9846RM
MODE 3
4
SOURCE/POWER
c
4
To pause playback, press -/J.
5
To eject the disc, press c.
Pressing -/J again will resume playback.
• Do not remove a CD during its eject cycle. Do not load more than
one disc at a time. A malfunction may result from doing either.
• If the CD does not eject, press and hold c for at least 2 seconds.
• The CD-player can play discs containing audio data and MP3
data.
• “MP3” is displayed during MP3 playback .
• The track display for MP3 data playback is the file numbers
recorded on the disc.
MP3 Play Display
The folder number and file number will be displayed as described
below.
g
-/J
f
82/NEWS
19/AF
3
4 5
TITLE
/PTY
6
Playback
1
Insert a disc with the label side facing up.
The disc will be pulled into the unit automatically.
When a disc is already inserted, press SOURCE/POWER
to switch to the CD mode.
The mode will change every time the button is pressed.
TUNER → CD → TUNER
2
While playing back MP3, press 19/AF or 82/NEWS
to select the desired folder.
Pressing and holding 19/AF or 82/NEWS will change
folders continuously.
10-EN
MP3
F01 T03
Folder number
display
File number
display
• If the folder number or file number are three digits, “F” or “T” is
not displayed.
• Press TITLE to switch the display. Please see “Displaying the
Title/Text” (page 15) for information about display switching.
Repeat Play
1
Press
played.
Scanning Programmes
4 to play back repeatedly the track being
1
The track (file) will be played repeatedly.
Press
play.
Press
mode.
6 to activate the Scan mode in the play
The first 10 seconds of each track (file) will be played
back in succession.
4 again and select OFF to deactivate repeat
To stop scanning, press
Scan mode.
6 again and deactivate the
CD mode:
RPT
: Only a track is repeatedly played back
↓
Tracks can be searched and played by using the CD text on the disc.
In the case of discs that do not support text, searches can be made by
using the track numbers.
(off)
1
MP3 mode:
RPT
: Only a file is repeatedly played back
↓
RPT
Searching from CD Text
2
: Only files in a folder are repeatedly
played back
↓
File/Folder Name Search (concerning MP3)
in the play or pause mode.
The tracks (files) on the disc will be played back in
random sequence.
To cancel M.I.X. play, press 5
again.
CD mode:
↓
M.I.X.
Turn the Rotary encoder (CDE-9848RB) or press
4 and 3 (CDE-9846R/CDE-9846RM) to select the
desired track, then press the Rotary encoder
(CDE-9848RB) or MODE (CDE-9846R/CDE9846RM).
This will play the selected track.
M.I.X. (Random Play)
Press 5
/PTY in the play mode.
This will set the search mode.
• Press and hold 3 /PTY for at least 2 seconds in the search mode
to cancel. Or, the search mode will be cancelled when an operation
has not been performed in 10 seconds.
• CD text search cannot be made during M.I.X. play.
(off)
1
Press 3
You can display and search for the folder and file name while
listening to the file currently being played back.
1
Press 3
/PTY to select File Name Search mode
or Folder Name Search mode in MP3 mode.
Folder Name Search mode
: The tracks are played back in
random sequence.
↓
(off)
MP3 mode:
↓
M.I.X.: Only files in a folder are played back in
random sequence.
↓
M.I.X.: The files are played back in random
sequence.
↓
(off)
2
3
Turn the Rotary encoder (CDE-9848RB) or press
4 and 3 (CDE-9846R/CDE-9846RM) within 10
seconds to select the desired folder.
Press the Rotary encoder (CDE-9848RB) or
MODE (CDE-9846R/CDE-9846RM) to play back the
first file in the selected folder.
• Search mode is cancelled by pressing and holding 3 /PTY for at
least 2 seconds in Folder Name Search mode.
• While in Folder Name Search mode, press 3 /PTY to switch to
File Name Search mode.
• “NO FILE” is displayed for 2 seconds if the folder that is selected
by the Folder Name Search mode contains no files.
• “ROOT” is displayed for a folder that does not have a folder
name.
• Folder Name search cannot be made during M.I.X. play.
Continued
11-EN
Supported playback sampling rates and bit rates
File Name Search mode
2
3
4
Press 19/AF or 82/NEWS to select another
Folder.
Select the desired file by turning the Rotary
encoder (CDE-9848RB) or press 4 and 3 (CDE9846R/CDE-9846RM) within 10 seconds.
Press the Rotary encoder (CDE-9848RB) or
MODE (CDE-9846R/CDE-9846RM) to play back the
selected file.
• File Name Search mode is cancelled by pressing and holding
3 /PTY for at least 2 seconds.
• While in File Name Search mode, press 3 /PTY to switch to
Folder Name Search mode.
• File Name search cannot be made during M.I.X. play.
You can search for tracks (files).
2
Press and hold 3
/PTY for at least 2 seconds in
the CD/MP3 mode to activate Quick Search mode.
Turn the Rotary encoder within 10 seconds to
select a desired track (file).
Note that for sampling rates, this device’s frame display (page
15) may not display correctly.
This device may not play back correctly depending on
sampling rates.
ID3 tags
This device supports ID3 tag v1 and v2.
If tag data is in an MP3 file, this device can display the title
(track title), artist name, and album name ID3 tag data.
This device can only display single-byte alphanumeric
characters (up to 30 for ID3 tags) and the underscore. For
non-supported characters, “NO SUPRT” is displayed.
The tag information may not be correctly displayed,
depending on the contents.
MP3 files are prepared, then written to a CD-R or CD-RW
using CD-R writing software. A disc can hold up to 510 files/
folders (including Root Folders). However, the maximum
number of folders is 255.
Media supported
The media that this device can play back are CD-ROMs, CDRs, and CD-RWs.
Corresponding File Systems
The selected track is played back immediately.
• Search mode is cancelled by pressing and holding 3
least 2 seconds in Quick Search mode.
Bit rates:
48 kHz, 44.1 kHz, 32 kHz, 24 kHz, 22.05 kHz,
16 kHz, 12 kHz, 11.025 kHz, 8 kHz
8 - 320 kbps
Producing MP3 discs
Quick Search (CDE-9848RB only)
1
MP3
Sampling rates:
/PTY for at
About MP3
CAUTION
Except for private use, duplicating audio data (including MP3
data) or distributing, transferring, or copying it, whether for
free or for a fee, without permission of the copyright holder is
strictly prohibited by the Copyright Act and by international
treaty.
This device supports discs formatted with ISO9660 Level 1 or
Level 2.
Under the ISO9660 standard, there are some restrictions to
remember.
The maximum nested folder depth is 8 (including the root
directory). The number of characters for a folder/file name is
limited.
Valid characters for folder/file names are letters A-Z (all
caps), numbers 0-9, and ‘_’ (underscore).
This device also can play back discs in Joliet, Romeo, etc.,
and other standards that conform to ISO9660. However,
sometimes the file names, folder names, etc., are not
displayed correctly.
What is MP3?
MP3, whose official name is “MPEG-1 Audio Layer 3,” is a
compression standard prescribed by the ISO, the International
Standardization Organization and MPEG which is a joint
activity institution of the IEC.
MP3 files contain compressed audio data. MP3 encoding is
capable of compressing audio data at extremely high ratios,
reducing the size of music files to as much as one-tenth their
original size. This is achieved while still maintaining near CD
quality. The MP3 format realizes such high compression ratios
by eliminating the sounds that are either inaudible to the
human ear or masked by other sounds.
Method for creating MP3 files
Audio data is compressed by using MP3 specified software.
For details on creating MP3 files, refer to the user's manual for
that software.
MP3 files that can be played back by this device have the file
extension “mp3”. Files with no extension cannot be played
back.
12-EN
Formats supported
This device supports CD-ROM XA, Mixed Mode CD,
Enhanced CD (CD-Extra) and Multi-Session.
This device cannot correctly play back discs recorded with
Track At Once or packet writing.
Order of files
The unit plays the files in the order that the writing software
writes them. Therefore, the playing order may not be the same
as the order you input. The playback order of the folders and
files is as follows. However, the folder and file playback order
differs from the folder and file number indicated on the
display.
1
Sound Setting
CDE-9848RB
Rotary encoder
(MODE)
BAND
2
2
Root folder
3
4
3
4
f
CDE-9846R/CDE-9846RM
5
5
6
g
CENT. f.
MODE
4
BAND
6
7
1
3
Folder
g
f
MP3 File
Terminology
Bit rate
This is the “sound” compression rate specified for encoding. The higher
the bit rate, the higher the sound quality, but also the larger the files.
Sampling rate
This value shows how many times per second the data is sampled
(recorded). For example, music CDs use a sampling rate of 44.1
kHz, so the sound is sampled (recorded) 44,100 times per second.
The higher the sampling rate, the higher the sound quality, but also
the larger the volume of data.
Encoding
Converting music CDs, WAVE (AIFF) files, and other sound files
into the specified audio compression format.
Tag
Song information such as track titles, artist names, album names,
etc., written into MP3 files.
MP3: ID3 tag
Root folder
The root folder is found at the top of the file system. The root folder
contains all folders and files.
Adjusting Bass/Treble/Balance (Between Left
and Right)/Fader (Between Front and Rear)/
Defeat
1
Press Rotary encoder (MODE) (CDE-9848RB) or
MODE (CDE-9846R/CDE-9846RM) repeatedly to
choose the desired mode.
Each press changes the mode as follows:
BASS LV → TRE LV → SUBW*1 → BALANCE → FADER →
DEFT → VOLUME → BASS LV
Bass level: -7 ~ +10
Treble level: -7 ~ +7
Subwoofer : 0 ~ +15
Balance : L15 ~ R15
Fader : R15 ~ F15
Defeat : ON/OFF
Volume : 0 ~ 35
• If the Rotary encoder (MODE) or MODE is not pressed within 5
seconds after selecting the BASS LV, TRE LV, BALANCE, FADER,
DEFT or SUBW mode, the unit automatically returns to normal
mode.
CDE-9848RB:
• If the Rotary encoder (MODE) is not pressed within 5 seconds
after selecting the BASS LV or TRE LV mode, the unit
automatically returns to normal mode.
CDE-9846R/CDE-9846RM:
• If the MODE is not pressed within 15 seconds after selecting the
BASS LV or TRE LV mode, the unit automatically returns to normal
mode.
*1 When the subwoofer mode is set to OFF, its level cannot be
adjusted.
Continued
13-EN
2
Turn the Rotary encoder (MODE) (CDE-9848RB)
or press 4 and 3 (CDE-9846R/CDE-9846RM) until
the desired sound is obtained in each mode.
By setting Defeat ON, previously adjusted settings of
BASS LV and TRE LV will return to the factory defaults.
Setting the Bass Control
You can change the bass frequency emphasis to create your own tonal
preference.
1
CDE-9848RB:
Press CENT. f. to select the Bass Control mode.
BASS LV → TRE LV → normal mode → BASS LV
CDE-9846R/CDE-9846RM:
Press MODE to select the Bass Control mode.
BASS LV → TRE LV → SUBW → BALANCE → FADER → DEFT
→ VOLUME → BASS LV
2-1
Setting the bass centre frequency:
Press g or f to select the desired bass centre
frequency.
60Hz ↔ 80Hz ↔ 100Hz ↔ 120Hz ↔ 60Hz
The displayed bass frequency is emphasized.
2-2
Setting the bass band width (Q-Factor):
Press BAND to select the desired bass band
width.
→ 1
→
2
→
3
→
4
(Narrow)← ...................................... →(Wide)
Change the boosted bass band width to wide or narrow. A
wide setting will boost a wide range of frequencies above
and below the centre frequency. A narrower setting will
boost only frequencies near the centre frequency.
2-3*2
Setting the bass level:
Turn the Rotary encoder (CDE-9848RB) or press
4 and 3 (CDE-9846R/CDE-9846RM) to select the
desired bass level (-7~+10).
You can emphasize or weaken the bass level.
• If no operation is performed within 15 seconds, the bass control
setting will be turned off automatically.
• The bass level settings will be individually memorized for each
source (FM, MW (LW), CD, etc.) until the setting is changed. The
bass frequency and bass band width settings adjusted for one
source are effective for all other sources (FM, MW (LW), CD etc.).
• This function is inoperable when DEFT is set to ON.
*2 CDE-9848RB:
The adjustment can also be made by pressing the Rotary encoder
(MODE). Refer to “Adjusting Bass/Treble/Balance (Between Left
and Right)/Fader (Between Front and Rear)/Defeat” (page 13).
14-EN
Setting the Treble Control
You can change the Treble Frequency emphasis to create your own
tonal preference.
1
CDE-9848RB:
Press CENT. f. to select the Treble Control mode.
BASS LV → TRE LV → normal mode → BASS LV
CDE-9846R/CDE-9846RM:
Press MODE to select the Treble Control mode.
BASS LV → TRE LV → SUBW → BALANCE → FADER → DEFT
→ VOLUME → BASS LV
2-1
Setting the treble Centre frequency:
Press g or f to select the desired treble
centre frequency.
7.5kHz ↔ 10.0kHz ↔ 12.5kHz ↔ 15.0kHz ↔ 7.5kHz
The displayed Treble frequency is emphasized.
2-2*2
Setting the treble level:
Turn the Rotary encoder (CDE-9848RB) or press
4 and 3 (CDE-9846R/CDE-9846RM) to select the
desired treble level (-7~+7).
You can emphasize the treble level.
• If no operation is performed within 15 seconds, the treble control
setting will be turned off automatically.
• The treble level settings will be individually memorized for each
source (FM, MW (LW), CD, etc.) until the setting is changed. The
Treble frequency settings adjusted for one source are effective for
all other sources (FM, MW (LW), CD, etc.).
• This function is inoperable when DEFT is set to ON.
*2 CDE-9848RB:
The adjustment can also be made by pressing the Rotary encoder
(MODE). Refer to “Adjusting Bass/Treble/Balance (Between Left
and Right)/Fader (Between Front and Rear)/Defeat” (page 13).
Turning Loudness On/Off
Loudness introduces a special low- and high-frequency emphasis at
low listening levels. This compensates for the ear’s decreased
sensitivity to bass and treble sound.
Press and hold Rotary encoder (MODE) (CDE9848RB) or MODE (CDE-9846R/CDE-9846RM) for at
least 2 seconds to activate or deactivate the loudness
mode.
The display shows “LOUD ON” and the “LD” indicator blinks
when the loudness mode is activated.
*1 Displayed during playback of a disc with CD Text.
“NO TEXT” will be displayed when the CD contains no Text data.
*2 “ROOT ” is displayed for a folder that does not have a folder
name.
*3 ID3 tag
If an MP3 file contains ID3 tag information, the ID3 tag
information is displayed (track name, artist name, and album
name). All other tag data is ignored.
“NO DATA” will be displayed when an MP3 file contains no ID3
tag information.
*4 The recording sampling rate and bit rate of the MP3 file are
displayed.
Other Functions
CDE-9848RB
-/J
Rotary encoder
About the indicator display
When displaying Title/Text, the following indicators are lit
according to the mode.
g
f
TITLE
CDE-9846R/CDE-9846RM
Bass Level Display
MODE
4
Indicator/
Mode
CD Mode
While displaying Title
-/J
3
g
f
MP3 Mode
—
—
While displaying Folder
Name
—
While displaying File
Name
—
While displaying Artist
Name∗
TITLE
Displaying the Title/Text
It is possible to display the CD title if the title has been previously
inputted (“Titling Discs” page 16). Text information, such as the disc
name and the track name, will be displayed if playing a CD text
compatible disc. It is also possible to display the folder name, the file
name, and the tag, etc., while playing MP3 files.
Press TITLE.
The display will change every time the button is pressed.
While displaying Text
(Disc Name)
While displaying Album
Name∗
While displaying Text
(Track Name)
While displaying Track
Name∗
∗Tag information
About “Title” and “Text”
Title:
With this device, it is possible to input the CD name (page 16).
This inputted name is referred to as a “title.”
You cannot input or display titles on radio station or MP3 discs.
The display in Radio mode:
PS (Programme Service Name) → Radio Text →
FREQUENCY → PS (Programme Service Name)
The display in CD mode:
TRACK NO./ELAPSED TIME → TEXT (DISC NAME)* → TEXT
(TRACK NAME)*1 → TITLE → TRACK NO./ELAPSED TIME
1
The display in MP3 mode:
FILE NO./ELAPSED TIME → FOLDER NO./FILE NO. →
FOLDER NAME*2 → FILE NAME → ARTIST NAME*3 →
ALBUM NAME*3 → TRACK NAME*3 → FRAME*4 → FILE NO./
ELAPSED TIME
Text:
Text compatible CDs contain text information such as the disc
name and track name. Such text information is referred to as
“text.”
• Some characters may not be displayed correctly with this device,
depending on the character type.
• When the Scroll Setting (page 17) is set to “MANU,” press and
hold TITLE for at least 2 seconds to scroll the Text information
only once (TEXT DISPLAY, FOLDER NAME DISPLAY, FILE
NAME DISPLAY or TAG DISPLAY mode).
• “NO SUPRT” is displayed when the desired text information
cannot be displayed on this unit.
• If the title was not previously input, “NO TITLE” is displayed.
• The text or tag information may not be correctly displayed,
depending on the contents.
15-EN
SETUP
Titling Discs
It is possible to title your favourite CDs.
You cannot input titles on radio station or MP3 discs.
1
2
3
4
Press TITLE and select the Title Display.
For details, see “Displaying the Title/Text” (page 15).
CDE-9848RB
Press and hold TITLE for at least 2 seconds. The
first character will blink.
Rotary encoder
BAND
Turn the Rotary encoder (CDE-9848RB) or press
4 and 3 (CDE-9846R/CDE-9846RM) to select the
desired letter/numeral/symbol available for naming.
Press Rotary encoder (CDE-9848RB) or MODE
(CDE-9846R/CDE-9846RM) to store the first
character.
The first character will stop blinking and the display will
automatically advance to the next character. When that
character begins to blink, you may choose the next letter
or symbol of your title.
5
You can flexibly customize the unit to suit your own preferences and
usage. From the SETUP menu, choose from Sound Customizing,
Visual Customizing, etc., to make your desired settings.
g
FUNC./SETUP
CDE-9846R/CDE-9846RM
Repeat steps 3 and 4 above to complete the titling.
Pressing the Rotary encoder (CDE-9848RB) or MODE
(CDE-9846R/CDE-9846RM) after entering the 8th
character automatically stores the title into memory.
f
MODE
4
BAND
When entering a title of less than 8 characters (for
example, 3 character title):
After entering 3 characters, the 4th character space will
be blinking. Go to step 6 to complete the title.
6
Press TITLE to record the title.
• If you cancel while entering a title, selected characters are not
written.
• You can enter 18 CD titles on this unit. If you try to store beyond
the limit, the display will show “FULL DATA.” At this point, no
more titles can be stored. To input a new title, one of the previously
inputted titles must first be deleted.
• When you want to erase a title, enter the “ ” symbol into all
spaces.
• The operations described in steps 3 to 5 must be made within 10
seconds. The input mode will be cancelled if no action is taken for
over 10 seconds.
Erasing Disc Title
3 g f
FUNC./SETUP
A typical SETUP procedure is shown in steps 1 to 4
as follows. See below for further information about
each SETUP menu.
1
Press and hold FUNC./SETUP for at least 2
seconds.
SETUP mode is activated.
2
Press g or f to select the desired SETUP
menu.
(e.g. Select SUBW)
1
2
3
4
5
Press TITLE to select the Title Display. Then, press
again and hold for at least 2 seconds.
Press and hold -/J for at least 2 seconds.
The title in the display will blink.
Press g or f repeatedly until the title you
want to erase is displayed.
Press and hold -/J for at least 2 seconds to erase
the title displayed.
Press TITLE to cancel the title erasing mode.
• You cannot erase CD-TEXT.
• “NO DATA” is displayed for 2 seconds if the title is not input in
step 2, or if the title is erased in step 4.
16-EN
FM-LV ↔ REG*1 ↔ PISK*2 ↔ DIM*3 ↔ SUBW ↔
CD-DA/CDDA/MP3 ↔ TYPE1/TYPE2 ↔ SCR ↔ AUX*3 ↔
(AUX NAME)*3/*4 ↔ PWR ↔ FM-LV
*1
*2
*3
*4
Refer to “Receiving RDS Regional (Local) Stations” (page 7)
Refer to “PI SEEK Setting” (page 8)
CDE-9848RB only
Displayed only when AUX is ON
3
Press BAND to change the setting.
4
Press FUNC./SETUP again.
(e.g. Select SUBW ON or SUBW OFF.)
The display returns to normal mode.
Sound Customizing
Adjusting Source Signal Levels
FM-LV HI (Initial setting) / FM-LV LO
If the difference in volume level between the CD player and FM radio
is too great, adjust the FM signal level.
Subwoofer On and Off
SUBW ON (Initial setting) / SUBW OFF
When the subwoofer is on, perform the steps below to adjust the
subwoofer output level.
1 Press the Rotary encoder (CDE-9848RB) or MODE
(CDE-9846R/CDE-9846RM) repeatedly to select the
SUBW mode.
BASS LV → TRE LV → SUBW* → BALANCE → FADER →
DEFT → VOLUME → BASS LV
2 To adjust the level, turn the Rotary encoder (CDE9848RB) or press 4 and 3 (CDE-9846R/CDE9846RM).
* When the subwoofer mode is set to OFF, its level cannot be
adjusted.
Visual Customizing
Dimmer Control (CDE-9848RB only)
DIM AUTO (Initial setting) / DIM MANU
Set the DIM control to AUTO to decrease the illumination brightness
of the unit with the head lights of the vehicle ON. This mode is useful
if you feel the unit's button lighting is too bright at night.
• If your vehicle should have a dimmer control for the
dashboardlights, never connect the DIMMER cable (orange) of the
radio to this dimmer control.
MP3
Playing MP3 Data
CD-DA (Initial setting) / CDDA/MP3
This product can playback CDs containing both CD and MP3 data.
However, in some situations (some enhanced CDs), playback may be
difficult. For these special cases, you can select playback of CD data
only. When a disc contains both CD or the MP3 data, playback starts
from the CD data portion of the disc.
CD-DA
: Only CD data can be played back.
CDDA/MP3 : Both CD data and MP3 file tracks can be
played back.
• Perform this setting before inserting a disc. If a disc has already
been inserted, perform the setting after you remove the disc.
External Device
Setting the AUX Mode (CDE-9848RB only)
AUX ON / AUX OFF (Initial setting)
You can input the audio of a connected external device (such as a
portable player) to the AUX input terminal of this unit, using a
commercially-available RCA cable.
You can change the AUX name display when AUX ON is set. Select
the AUX name by pressing g or f.
Connecting to an External Amplifier
PWR ON (Initial setting) / PWR OFF
When an external amplifier is connected, sound quality can be
improved by stopping the power supply of the built-in amplifier.
PWR OFF : Use this mode when the front pre-amplifier of the
unit is used to drive an external amplifier
connected to the speakers. In this setting, the
head unit’s internal amplifier has no output to
drive speakers.
Scroll Setting
Front
left
SCR AUTO / SCR MANU (Initial setting)
Amplifier
Front
right
This CD player can scroll the disc and track names recorded on CDTEXT discs, as well as the text information of MP3 files, folder
names, and tags.
SCR AUTO : The CD text information, the text information of
folder and file names, and the tags are scrolled
automatically.
SCR MANU : The display is scrolled only when a disc is
loaded or when a track is changed, etc.
PWR ON : The speakers are driven by the built-in amplifier.
Speakers
SPEAKER
RIGHT FRONT
• The unit scrolls CD text names, folder names, file names or tag
display. The disc titles input manually (page 16) cannot be scrolled.
Scroll Type Setting
TYPE1 (Initial setting) / TYPE2
Choose from two scrolling methods.
Select the type you prefer.
TYPE1
TYPE2
: The characters scroll sequentially, appearing from
the right side of the display.
: The characters are displayed one by one, and
disappear one by one from the left side of the
display after the screen is filled up with the
characters.
SPEAKER
RIGHT REAR
SPEAKER
LEFT REAR
SPEAKER
LEFT FRONT
Front
right
Rear
right
Rear
left
Front
left
• No sound is produced by the system when the power output is set to
OFF.
17-EN
Information
In Case of Difficulty
If you encounter a problem, please turn the power off, then on again.
If the unit is still not functioning normally, please review the items in
the following checklist. This guide will help you isolate the problem
if the unit is at fault. Otherwise, make sure the rest of your system is
properly connected or consult your authorized Alpine dealer.
Basic
No function or display.
• Vehicle's ignition is off.
- If connected following instructions, the unit will not
operate with the vehicle's ignition off.
• Improper power lead (Red) and battery lead (Yellow)
connections.
- Check power lead and battery lead connections.
• Blown fuse.
- Check the fuse of the unit; replace with the proper value if
necessary.
• Internal micro-computer malfunctioned due to interference
noise etc.
- Press the RESET switch with a ballpoint pen or other
pointed article.
Radio
Unable to receive stations.
• No antenna or open connection in cable.
- Make sure the antenna is properly connected;
replace the antenna or cable if necessary.
Unable to tune stations in the seek mode.
• You are in a weak signal area.
- Make sure the tuner is in the DX mode.
• If the area you are in is a primary signal area, the antenna may
not be grounded and connected properly.
- Check your antenna connections; make sure the antenna is
properly grounded at its mounting location.
• The antenna may not be the proper length.
- Make sure the antenna is fully extended; if broken, replace
the antenna with a new one.
Broadcast is noisy.
• The antenna is not the proper length.
- Extend the antenna fully; replace it if it is broken.
• The antenna is poorly grounded.
- Make sure the antenna is grounded properly at its mounting
location.
CD
CD Player not functioning.
• Out of operating temperature range +50˚C (+120˚F) for CD.
- Allow the vehicle's interior (or trunk) temperature to cool.
CD playback sound is wavering.
• Moisture condensation in the CD Module.
- Allow enough time for the condensation to evaporate (about
1 hour).
CD insertion not possible.
• A CD is already in the CD player.
- Eject the CD and remove it.
• The CD is being improperly inserted.
- Make sure the CD is being inserted following instructions in
the CD Player Operation section.
Unable to fast forward or backward the CD.
• The CD has been damaged.
- Eject the CD and discard it; using a damaged CD in your unit
can cause damage to the mechanism.
CD playback sound skips due to vibration.
• Improper mounting of the unit.
- Securely re-mount the unit.
• The disc is very dirty.
- Clean the disc.
• The disc has scratches.
- Change the disc.
• The pick-up lens is dirty.
- Do not use a commercial available lens cleaner disc. Consult
your nearest Alpine dealer.
CD playback sound skips without vibration.
• The disc is dirty or scratched.
- Clean the disc; damaged disc should be replaced.
Error displays (built-in CD player only)
• Mechanical error
- Press c. After the error indication disappears, insert the disc
again. If the above-mentioned solution does not solve the
problem, consult your nearest Alpine dealer.
CD-R/CD-RW playback not possible
• Close session (finalization) has not been performed.
- Perform finalization and attempt playback again.
MP3
MP3 is not played back.
• Writing error occurred. The CD format is not compatible.
- Make sure the CD has been written in a supported format.
Refer to “About MP3” (pages 12-13), then rewrite in the
format supported by this device.
Audio
The sound is not output from the speakers.
• Unit has no output signal of the internal amplifier.
- PWR is switched to “ON” (page 17).
18-EN
Indication for CD Player
HI TEMP
• Protective circuit is activated due to high temperature.
- The indicator will disappear when the temperature
returns to normal operating range.
NO DISC
• No CD is inserted.
- Insert a CD.
• Although a disc is inserted, “NO DISC” is displayed and the
unit does not start to play or eject the disc.
- Remove the disc by following these steps:
Press the c button again for at least 2 seconds.
If the disc still does not eject, consult your Alpine dealer.
ERROR
• Mechanism error.
1) Press the c button and eject the CD.
If not ejecting, consult your Alpine dealer.
2) When the error indication remains after ejecting, press the
c button again.
If the error indication still does not turn off after pressing
the c button for a few times, consult your Alpine dealer.
• When “ERROR” is displayed:
If that the disc cannot be ejected by pressing c, press the
RESET switch (refer to page 5) and press c again.
If the disc still cannot be ejected, consult your Alpine dealer.
• A disc that is not compatible with the unit is inserted.
- Insert a disc that is compatible with the unit.
UNSUPORT
• The disc is not written in a MP3 supported format.
- Use a disc written at the MP3 supported format.
Specifications
FM TUNER SECTION
Tuning Range
Mono Usable Sensitivity
Alternate Channel Selectivity
Signal-to-Noise Ratio
Stereo Separation
Capture Ratio
87.5 – 108.0 MHz
0.7 µV
80 dB
65 dB
35 dB
2.0 dB
MW TUNER SECTION
Tuning Range
Sensitivity (IEC Standard)
531 – 1,602 kHz
25.1 µV/28 dB
LW TUNER SECTION
Tuning Range
Sensitivity (IEC Standard)
153 – 281 kHz
31.6 µV/30 dB
CD SECTION
Frequency Response
Wow & Flutter (% WRMS)
Total Harmonic Distortion
Dynamic Range
Signal-to-Noise Ratio
Channel Separation
5 – 20,000 Hz (±1 dB)
Below measurable limits
0.008% (at 1 kHz)
95 dB (at 1 kHz)
105 dB
85 dB (at 1 kHz)
PICKUP
Wave length
Laser power
795 nm
CLASS I
GENERAL
Power Requirement
Maximum Power Output
Maximum Pre-Output Voltage
Bass
Treble
Weight
14.4 V DC
(11–16 V allowable)
45 W × 4
2 V/10k ohms
+20/-14 dB at 60 Hz
±14 dB at 10 kHz
1.6 kg (3 lbs. 8 oz)
CHASSIS SIZE
Width
Height
Depth
178 mm (7")
50 mm (2")
160 mm (6-1/4")
NOSEPIECE SIZE
Width
Height
Depth
170 mm (6-3/4")
46 mm (1-13/16")
18 mm (11/16")
• Due to continuous product improvement, specifications and design
are subject to change without notice.
CAUTION
CLASS 1
LASER PRODUCT
(Bottom side of player)
19-EN
Installation and Connections
Before installing or connecting the unit, please read the
following and pages 2 to 4 of this manual thoroughly
for proper use.
Warning
MAKE THE CORRECT CONNECTIONS.
Caution
HAVE THE WIRING AND INSTALLATION DONE BY
EXPERTS.
The wiring and installation of this unit requires special technical
skill and experience. To ensure safety, always contact the dealer
where you purchased this product to have the work done.
Failure to make the proper connections may result in fire or
product damage.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM
SECURELY.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
Be sure to use only the specified accessory parts. Use of other
than designated parts may damage this unit internally or may not
securely install the unit in place. This may cause parts to become
loose resulting in hazards or product failure.
(Check with your dealer if you are not sure.) Failure to do so may
result in fire, etc.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE
NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to
electrical shorts.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying capacity of
the wire and result in fire or electric shock.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING
HOLES.
When drilling holes in the chassis for installation, take
precautions so as not to contact, damage or obstruct pipes, fuel
lines, tanks or electrical wiring. Failure to take such precautions
may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR
STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or any other
safety-related system), or tanks should NEVER be used for
installations or ground connections. Using such parts could
disable control of the vehicle and cause fire etc.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE
REACH OF CHILDREN.
Swallowing them may result in serious injury.
If swallowed, consult a physician immediately.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER
VEHICLE OPERATION, SUCH AS THE STEERING WHEEL
OR GEARSHIFT.
Doing so may obstruct forward vision or hamper movement etc.
and results in serious accident.
IMPORTANT
Please record the serial number of your unit in the space provided
below and keep it as a permanent record. The serial number or the
engraved serial number is located on the bottom of the unit.
20-EN
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR
PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like the
seat rails) or sharp or pointed edges. This will prevent crimping
and damage to the wiring. If wiring passes through a hole in
metal, use a rubber grommet to prevent the wire’s insulation from
being cut by the metal edge of the hole.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE
OR DUST.
Avoid installing the unit in locations with high incidence of
moisture or dust. Moisture or dust that penetrates into this unit
may result in product failure.
Precautions
• Be sure to disconnect the cable from the (–) battery post before
installing your CDE-9848RB/CDE-9846R/CDE-9846RM.
This will reduce any chance of damage to the unit in case of a
short-circuit.
• Be sure to connect the colour coded leads according to the
diagram. Incorrect connections may cause the unit to
malfunction or damage to the vehicle's electrical system.
• When making connections to the vehicle's electrical system, be
aware of the factory installed components (e.g. on-board
computer). Do not tap into these leads to provide power for
this unit. When connecting the CDE-9848RB/CDE-9846R/
CDE-9846RM to the fuse box, make sure the fuse for the
intended circuit of the CDE-9848RB/CDE-9846R/CDE9846RM has the appropriate amperage. Failure to do so may
result in damage to the unit and/or the vehicle. When in doubt,
consult your Alpine dealer.
• The CDE-9848RB/CDE-9846R/CDE-9846RM uses female
RCA-type jacks for connection to other units (e.g. amplifier)
having RCA connectors. You may need an adaptor to connect
other units. If so, please contact your authorized Alpine dealer
for assistance.
• Be sure to connect the speaker (–) leads to the speaker (–)
terminal. Never connect left and right channel speaker cables
to each other or to the vehicle body.
SERIAL NUMBER:
INSTALLATION DATE:
INSTALLATION TECHNICIAN:
PLACE OF PURCHASE:
3
Installation
Accessory List
• Head unit ........................................................................ 1
• Power cable .................................................................... 1
• Mounting sleeve ............................................................. 1
• Carrying case ................................................................. 1
• Rubber Cap .................................................................... 1
• Hex Bolt .......................................................................... 1
• Screw (M5 × 8) ................................................................ 4
• Owner’s Manual ....................................................... 1 set
Slide the CDE-9848RB/CDE-9846R/CDE-9846RM
into the dashboard. When the unit is in place, make
sure the locking pins are fully seated in the down
position. This can be done by pressing firmly in on
the unit while pushing the locking pin down with a
small screwdriver. This ensures that the unit is
properly locked and will not accidentally come out
from the dashboard. Install the Detachable Front
Panel.
Note:
The main unit must be mounted within 35 degrees of the horizontal
plane, back to front.
Lock pin
Less than 35°
Removal
1 Remove the detachable front panel.
1
Rubber Cap
(Included)
Bracket
Hex Bolt
(Included)
2 Use a small screwdriver (or similar tool) to push the
locking pins to the “up” position (see above drawing).
As each pin is unlocked, gently pull out on the unit to
make sure it does not re-lock before unlocking the
second pin.
3 Pull the unit out, keeping it unlocked as you do so.
Dashboard
<JAPANESE CAR>
Mounting sleeve
(Included)
this unit
Slide mounting sleeve from main unit (see
“Removal” on this page). Slide the mounting sleeve
into the dashboard and fix it with the metal
shackles.
Front frame
2
Metal Mounting Strap
Screw
∗
Screws (M5 × 8)
(Included)
Bolt Stud
this unit
Hex Nut (M5)
this unit
When your vehicle has the Bracket, mount the long
hex bolt onto the rear panel of the CDE-9848RB/
CDE-9846R/CDE-9846RM and put the Rubber Cap
on the hex bolt. If your vehicle does not have the
Mounting Support, reinforce the head unit with the
metal mounting strap (not supplied). Connect all
the leads of the CDE-9848RB/CDE-9846R/CDE9846RM according to details described in the
CONNECTION section.
Mounting Bracket
• For the screw *, provide a proper screw to the chassis installing
location.
21-EN
Connections
Antenna
:
1
ISO Antenna Plug
JASO Antenna Plug
(Pink/Black)
AUDIO INTERRUPT IN
2
(Blue/White)
REMOTE TURN-ON
3
To vehicle phone
To amplifier or equalizer
(Orange)
DIMMER
To the instrument cluster illumination lead
(CDE-9848RB only)
(Red)
(Black)
(Blue)
4
5
IGNITION
To power antenna
6
GND
POWER ANT
9
Ignition Key
7
8
(Yellow)
BATTERY
Battery
!
"
#
$
Speakers
.
%
(Green)
&
(Green/Black)
(
(White)
)
(White/Black)
~
(Grey/Black)
+
(Grey)
,
(Violet/Black)
-
(Violet)
Rear Left
Front Left
Front Right
Rear Right
Amplifier
/
;
/
External Device
(Such as a portable player)
22-EN
Front or Subwoofers
1 Antenna Receptacle
9 ISO Power Supply Connector
2 Audio Interrupt In Lead (Pink/Black)
Connect this lead to the Audio Interface output of a cellular
phone which provides ground shorting when a call is
received.
! Fuse Holder (10A)
3 Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
4 Dimmer Lead (Orange) (CDE-9848RB only)
This lead may be connected to the vehicle’s instrument
cluster illumination lead. This will enable the vehicle’s
dimmer control to dim the backlighting of the unit.
5 Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle’s fuse
box or another unused power source which provides (+) 12V
only when the ignition is turned on or in the accessory
position.
6 Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
7 Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
• This lead should be used only for controlling the vehicle's power
antenna. Do not use this lead to turn on an amplifier or a signal
processor, etc.
" Steering Remote Control Interface Connector
To steering remote control interface box.
# Front/Subwoofer* Output RCA Connectors
* When Subwoofer is set to OFF: Output is from front speakers.
When Subwoofer is set to ON: Output is from Subwoofer.
$ Power Supply Connector
% Left Rear (+) Speaker Output Lead (Green)
& Left Rear (–) Speaker Output Lead (Green/Black)
( Left Front (+) Speaker Output Lead (White)
) Left Front (–) Speaker Output Lead (White/Black)
~ Right Front (–) Speaker Output Lead (Grey/Black)
+ Right Front (+) Speaker Output Lead (Grey)
, Right Rear (–) Speaker Output Lead (Violet/Black)
- Right Rear (+) Speaker Output Lead (Violet)
. ISO Connector (Speaker Output)
/ RCA Extension Cable (sold separately)
: ISO/JASO Antenna Adapter (sold separately)
An ISO/JASO antenna adapter may be required, depending
on the vehicle.
; AUX Input RCA Connector (CDE-9848RB only)
This connector allows for input of audio from an external
device (such as a portable player), using a commercially
available RCA cable.
8 Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle’s
battery.
To prevent external noise from entering the audio system.
• Locate the unit and route the leads at least 10 cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
• If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise
suppressors, contact them for further information.
• Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
23-EN
Appendix
Product Information Card
Produkt-Informationskarte Carte d’informations sur
le produit
Tarjeta de información del
producto
English
Deutsch
Français
Español
Filling in this Product Information Card is
voluntary. If you fill in this card and send
it to Alpine, your data will be tabulated
into reference data for future Alpine
product development. In addition, in the
future you may receive information about
new products or Survey Mail requesting
additional opinions about Alpine products
or services. If you agree to the above
term, please sign your name in the
indicated space and return the card. Any
additional comments or inquiries may be
sent to : Person in charge of Customer
Service department Alpine Electronics
(Europe) GmbH.
Frankfurter Ring 117, 80807 München, Germany
Phone: +49-(0)89-32 42 640
Das Ausfüllen dieser Produktinformations-Karte
ist freiwillig. Sollten Sie diese Karte
vervollständigen, so werden die Daten für
zukünftige Produktentwicklungen von Alpine als
Referenzdaten herangezogen. Ebenso können Sie
in der Zukunft Informationen über neue Alpine
Produkte erhalten oder uns auch Ihre Meinung
über Alpine Produkte und Dienstleistungen im
Rahmen von Kunden-Befragungen mitteilen.
Stimmen Sie dem Kontakt durch Alpine zu, so
würden wir Sie bitten, in dem dafür vorgesehenen
Feld zu unterschreiben und die Karte kostenfrei
an uns zurückzuschicken. Zusätzliche
Kommentare und Meinungen können Sie gerne
an den zuständigen Kontakt im Kundendienst
Alpine Electronics (Europe) GmbH senden.
Frankfurter Ring 117, 80807 München, Germany
Phone: 089-32 42 640
En remplissant volontairement cette fiche,
et en l’envoyant à Alpine, vous acceptez
que ces informations soient utilisées par
Alpine, dans le cadre de développement
de nouveaux produits. Par ailleurs, vous
autorisez Alpine à solliciter votre opinion
par mailing sur de nouveaux produits ou
services. Si vous acceptez les termes cidessus, veuillez signer cette carte à
l’endroit indiqué, et nous la retourner.
Tout autre commentaire ou demande doit
être adressé à l’attention de: Responsable
du service consommateur Alpine
Electronics (Europe) GmbH.
Frankfurter Ring 117, 80807 München, Germany
Phone: +49-(0)89-32 42 640
El envío de la información solicitada es
voluntario. Si Vd. nos la remite, será
utilizada de modo confidencial para el
desarrollo de futuros productos Alpine. Si
Vd. desea recibir información sobre
nuevos productos de nuestra gama,
indique su nombre en el espacio
designado y remítanos la tarjeta.
Cualquier solicitud adicional puede ser
enviada a : Persona responsable del
Servicio de Atención al Cliente de Alpine
Electronics (Europe) GmbH.
Frankfurter Ring 117, 80807 München, Germany
Phone: +49-(0)89-32 42 640
Q1. PRODUCT PURCHASED
1. Cassette Player
2. CD Player
3. MD Player
4. DVD Player
5. CD Changer
6. Amplifier
7. Speaker
8. Subwoofer
9. Monitor Controller
10. Video Monitor
11. Navigation
12. Processor/Equalizer
13. CD/Video CD Changer
14. Other
Q2. MODEL NUMBER:
Q3. DATE OF PURCHASE:
Month:
Year:
Q4. If navigation system, which
monitor?
1. Alpine → (Model No.)
2. Other → (Brand Name)
Q5. STORE TYPE WHERE
PURCHASED:
1. Car Audio Specialist
2. Audio/Video Store
3. Electronics/Appliance Store
4. Car Accessories Shop
5. Other
Q6. Type of vehicle in which this unit is
installed:
Make:
Purchased
Year:
Model:
Model
Year:
Q7. How was this vehicle purchased?
1. Purchase
2. Lease
Q8. Purpose of buying this unit?
1. Addition
2. Replacement
↓
• Previous brand replaced?
1. Factory installed
2. Alpine
3. Other → (Brand Name)
Q9. Have you purchased Alpine
products before?
1. First time
2. Two or More times
Q10.When you purchased this Alpine
unit, did you compare it with other
brand?
1. Yes → (Brand Name)
2. No.
Q11.GENDER
1. Male
2. Female
Q12.AGE
Q13.MARITAL STATUS
1. Single
2. Married
Q14.OCCUPATION
1. Company Owner/Self-employed/
Freelance
2. Manager
3. Company Employee
4. Civil Servant
5. Educator
6. Student
7. Other
Q15.Comments
Q1. PRODUIT ACHETE
Q1. gekauftes Gerät
1. Kassetten-Spieler
2. CD-Spieler
3. MD-Spieler
4. DVD-Spieler
5. CD-Wechsler
6. Verstärker
7. Lautsprecher
8. Subwoofer
9. Monitor-Controller
10. Video-Monitor
11. Navigationssystem
12. Prozessor/Equalizer
13. CD/Video-CD-Wechsler
14. andere
Q2. Modellnummer:
Q3. Kaufdatum:
Monat:
Q2. NUMERO DU MODELE:
Q3. DATE D’ACHAT:
Jahr:
Q4. Falls Navigationssystem:
Welcher Monitor?
1. Alpine → (Modellnr.)
2. Anderer Hersteller →
(Herstellername)
Q5. Art des Geschäfts, in dem Sie das
Gerät gekauft haben:
1. Spezialist für Auto-Audioanlagen
2. Audio/Video-Geschäft
3. Elektro-Geschäft
4. Autozubehör-Geschäft
5. Anderer Hersteller
Q6. Art des Fahrzeugs, in das das
Gerät installiert wurde:
Marke:
gekauft im
Jahr:
Modell:
Baujahr:
Q7. Wie haben Sie das Fahrzeug
gekauft?
1. Kauf
2. Leasing
Q8. Zweck des Kaufs dieses Geräts?
1. Zusätzlich
2. Austausch
↓
• Marke des ausgetauschten Geräts?
1. Serienmäßige Ausstattung
2. Alpine
3. Anderer Hersteller →
(Herstellername)
Q9. War dies das erste Mal, dass Sie
ein Alpine-Gerät gekauft haben?
1. Erstes Mal
2. Zweites Mal oder öfter
Q10.Haben Sie dieses Alpine-Gerät vor
dem Kauf mit Geräten anderer
Hersteller verglichen?
1. Ja → (Herstellername)
2. Nein
Q11.Geschlecht
1. Männlich
2. Weiblich
Q12.Alter
Q13.Familienstand
1. Ledig
2. Verheiratet
Q14.Beruf
1. Selbständige/Firmeninhaber/freiberuflich
Tätige
2. Leitende Angestellte
3. Sonstige Angestellte
4. Beamte
5. Schulbildung
6. Studium
7. Sonstige
Q15.Kommentar:
1. Lecteur de cassette
2. Lecteur de CD
3. Lecteur MD
4. Lecteur DVD
5. Changeur de CD
6. Amplificateur
7. Haut-parleur
8. Haut-parleur de graves
9. Station Multimedia
10. Moniteur Vidéo
11. Navigation
12. Processeur/Egaliseur
13. Changeur de CD/CD Vidéo
14. Autre
Mois:
Année:
Q4. Si c’est un système de navigation,
quel moniteur?
1. Alpine → (N° du modèle)
2. Autre → (Marque)
Q5. TYPE DE MAGASIN OU VOUS
AVEZ ACHETE LE PRODUIT:
1. Spécialiste autoradio
2. Magasin audio/vidéo
3. Magasin d’électronique/appareils
4. Magasin d’accessoires automobiles
5. Autre
Q6. Type de véhicule dans lequel cet
appareil est installé:
Marque:
Année
d’achat:
Modèle:
Année du
modèle:
Q7. Comment avez-vous acheté ce
véhicule?
1. Achat
2. Location-bail
Q1. Producto Comprado
1. Radio/Cassette
2. Radio/CD
3. Reproductor de MD
4. Reproductor de DVD
5. Cambiador de CD
6. Amplificador
7. Altavoz
8. Subwoofer
9. Monitor de control
10. Monitor de video
11. Sistema de navegación
12. Procesador/Ecualizador
13. Cambiador de CD/Video CD
14. Otros
Q2. Número de modelo:
Q3. Fecha de compra:
Mes:
Año:
Q4. En caso de sistema de
navegación, ¿qué monitor?
1. Alpine → (N° de modelo)
2. Otros → (Nombre de marca)
Q5. TIPO DE TIENDA DONDE
COMPRÓ:
1. Especialista en audio de automóviles
2. Tienda de audio/video
3. Tienda de electrónica/electrodomésticos
4. Tienda de accesorios automovilísticos
5. Otros
Q6. Tipo de vehiculo en que la unidad
está instalada:
Marca:
Año de
compra:
Modelo:
Año del
modelo:
Q7. ¿Cómo fue comprado este
vehiculo?
1. compra
2. Leasing
Q8. Pourquoi avez-vous acheté cet
appareil?
Q8. ¿Propósito de comprar esta
unidad?
1. Addition
2. Remplacement
↓
• Marque précédente remplacée?
1. Installée en usine
2. Alpine
3. Autre → (Marque)
1. Mejora del sistema
2. Sustitución
↓
• ¿Sustitución de marca anterior?
1. Instalado en la fábrica
2. Alpine
3. Otros → (Nombre de marca)
Q9. Aviez-vous déjà acheté des
produits Alpine?
1. Première fois
2. Deux fois ou plus
Q10.Lorsque vous avez acheté ce
produit Alpine, l’avez-vous
comparé à une autre marque?
1. Oui → (Marque)
2. Non
Q11.SEXE
1. Masculin
2. Féminin
Q12.AGE
Q13.SITUATION DE FAMILLE
1. Célibataire
2. Marié
Q14.PROFESSION
1. Entrepreneur/Travailleur indépendant/
Free-lance
2. Directeur
3. Employé de bureau
4. Fonctionnaire
5. Educateur
6. Etudiant
7. Autre
Q15.Commentaires
Q9. ¿Ha comprado Vd. productos
Alpine anteriormente?
1. Primera vez
2. Dos o más veces
Q10.Cuando usted compró esta unidad
Alpine, ¿la comparó con otros
fabricantes?
1. Si → (Nombre de marca)
2. No
Q11.SEXO
1. Masculino
2. Femenino
Q12.Edad
Q13.Estado civil
1. Soltero
2. Casado
Q14.Ocupación
1. Propietario de empresa/Autónomo/
Profesional independiente
2. Gerente
3. Empleado de compañia
4. Empleado público
5. Profesor
6. Estudiante
7. Otros
Q15.Comentarios
Scheda informazioni
prodotto
Italiano
La compilazione di questa formulario è
volontaria. Se compilate questo formulario,
ritornandolo ad Alpine, i Vostri dati saranno
raccolti in un file di riferimento per lo sviluppo
dei nuovi prodotti Alpine. In aggiunta Voi potrete
ricevere in futuro informazioni riguardanti i nuovi
prodotti o la richiesta di una Vostra opinione
circa i prodotti o i servizi forniti da Alpine. Se
siete d’accordo, Vi preghiamo di ritornarci il
formulario completato negli appositi spazi con i
Vostri dati. In caso desideriate fornire altri
commenti o richiedere informazioni aggiuntive,
potete indirizzare il tutto a : Responsabile
dipartimento Servizio Clienti Alpine Electronics
(Europe) GmbH.
Frankfurter Ring 117, 80807 München, Germany
Phone: +49-(0)89-32 42 640
Q1. PRODOTTO ACQUISTATO
1. Lettore di cassette
2. Lettore CD
3. Lettore MD
4. Lettore DVD
5. CD Changer
6. Amplificatore
7. Altoparlante
8. Subwoofer
9. Radio Monitor
10. Monitor video
11. Sistema di navigazione
12. Processore/equalizzatore
13. Cambia CD/Video CD
14. Altro
Q2. NUMERO MODELLO:
Q3. DATA DI ACQUISTO:
Mese:
Anno:
Q4. In caso di acquisto di un sistema di
navigazione, quale monitor
possiede?
1. Alpine → (No. Modello)
2. Altro → Nome marca
Q5. NEGOZIO DI ACQUISTO:
I agree to the above stated terms of the Alpine Product Information Card.
Ich stimme dem Kontakt durch Alpine für Informations- und Befragungszwecke zu.
J’accepte les termes de cette carte d’information produit Alpine.
Estoy conforme con los términos de la tarjeta de información sobre producto de Alpine.
Accetto i termini della scheda informazioni prodotti Alpine.
1. Specialista Car Stereo
2. Negozio di audio/video
3. Negozio di elettronica/elettrodomestici
4. Negozio accessori automobile
5. Altro
(Date/Datum/Date/Fecha/Data)
(Signature/Unterschrift/Signature/Firma)
Q6. Tipo di veicolo posseduto:
Marca:
Anno
acquisto:
Modello:
Anno
modello:
Q7. Modalità acquisto
1. Acquisto
2. Leasing
Q8. Scopo acquisto
1. Aggiunta
2. Sostituzione
↓
• Marca sostituita
1. Installato di fabbrica
2. Alpine
3. Altro → (Nome marca)
Q9. Avevate già acquistato prodotti
Alpine?
1. No
2. Due o tre volte
Q10.Nell’acquistarlo, avete paragonato
questo prodotto ad un’altra marca?
1. Si → (Nome marca)
2. No
Name/Nom/Nombre/Nome
(First Name/Vorname/Prénom/Primer nomble/Nome)
(Surname/Familienname/Nom de famille/Apellido/Cognome)
Home Address/Privatanschrift/Adresse/Dirección/Indirizzo
(Street/Straße/Rue/Calle/Via) (Post Code/Postleitzahl/Code postal/Código postal/Codice postale)
(Town/City/Stadt/Ville/Ciudad/Città) (Country/Land/Pays/País/Paese)
Telephone Number:
E-Mail/Correo electrónico:
Q1
NO.
Other
Q3
Month
Q5
NO.
Other
Q2
Q4
Year
Q11.SESSO
1. Maschile
2. Femminile
Q12.ETÀ
Q13.STATO CIVILE
1. Celibe/nubile
2. Coniugato/coniugata
Q14.LAVORO
1. Proprietario di azienda/artigiano/libero
professionista
2. Manager
3. Impiegato
4. Impiegato statale
5. Insegnante
6. Studente
7. Altro
Q15.Commenti
Q7
Q8
NO.
Q9
Q6
NO.
Q12
Q15
Model:
Purchased Year:
ModelYear:
1
years old
Comments
Previous brand replaced.
1.
2
NO.
NO.2. Brand Name
Make:
Q10
NO.
NO.1. Model No.
1
Brand Name
2
Q13
2.
Brand Name
3.
Q11
NO.
NO.
Q14
NO.
Other
Download PDF