VTech | 6052 | Specifications | VTech 6052 Specifications

Congratulations
on purchasing your new VTech product.
Before using this telephone, please read the
Important safety instructions
on page 39 of this manual.
This manual has all the feature operations and troubleshooting necessary to install
and operate your new VTech telephone. Please review this manual thoroughly to
ensure proper installation and operation of this innovative and feature rich VTech
product. For support, shopping, and everything new at VTech, visit our website at
www.vtechphones.com. In Canada, please visit www.vtechcanada.com.
www.vtechphones.com
Table of contents
Installation . . . . . . . . . . . . . . . . . . . . . . . . 1
Parts checklist . . . . . . . . . . . . . . . . . . . . . . 1
Install handset battery . . . . . . . . . . . . . . . . . . 2
Telephone base installation . . . . . . . . . . . . . . . 3
Desk/table bracket installation . . . . . . . . . . . . . . 4
Dial type . . . . . . . . . . . . . . . . . . . . . . . . . 4
DSL filter . . . . . . . . . . . . . . . . . . . . . . . . . 5
Telephone settings . . . . . . . . . . . . . . . . . . . . 6
Handset layout . . . . . . . . . . . . . . . . . . . . . . 6
Telephone base layout . . . . . . . . . . . . . . . . . . 7
Date and time . . . . . . . . . . . . . . . . . . . . . . 8
Ring melody . . . . . . . . . . . . . . . . . . . . . . . 8
Ring volume . . . . . . . . . . . . . . . . . . . . . . . 9
Battery low tone . . . . . . . . . . . . . . . . . . . . . 9
Out of range tone . . . . . . . . . . . . . . . . . . . . 10
Key tone . . . . . . . . . . . . . . . . . . . . . . . . . 10
Edit handset name . . . . . . . . . . . . . . . . . . . 11
Language . . . . . . . . . . . . . . . . . . . . . . . . 11
Dial type . . . . . . . . . . . . . . . . . . . . . . . . . 12
Clear voicemail . . . . . . . . . . . . . . . . . . . . . 12
Reset to default settings . . . . . . . . . . . . . . . . 13
Temporary tone dialing . . . . . . . . . . . . . . . . . 13
Basic operation . . . . . . . . . . . . . . . . . . . . . 14
Make, answer and end calls . . . . . . . . . . . . . . 14
Options while on calls . . . . . . . . . . . . . . . . . . 14
Speakerphone . . . . . . . . . . . . . . . . . . . . . . 14
Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Call waiting . . . . . . . . . . . . . . . . . . . . . . . 14
Intercom call . . . . . . . . . . . . . . . . . . . . . . . 15
Multiple handset use . . . . . . . . . . . . . . . . . . 15
Answer an external call during an intercom call . . . . 15
Transfer an external call . . . . . . . . . . . . . . . . . 16
Find handset . . . . . . . . . . . . . . . . . . . . . . 16
Advanced operation . . . . . . . . . . . . . . . . . . . 17
Directory . . . . . . . . . . . . . . . . . . . . . . . . . 17
Review the directory . . . . . . . . . . . . . . . . . . 17
Search the directory . . . . . . . . . . . . . . . . . . . 17
Chart of characters . . . . . . . . . . . . . . . . . . . 18
Store an entry in the directory . . . . . . . . . . . . . 19
Dial a directory entry . . . . . . . . . . . . . . . . . . 19
Edit an entry in the directory . . . . . . . . . . . . . . 20
Delete from the directory . . . . . . . . . . . . . . . . 20
About caller ID information . . . . . . . . . . . . . . . 21
Call log . . . . . . . . . . . . . . . . . . . . . . . . . 22
Review the call log . . . . . . . . . . . . . . . . . . . 22
Dial a call log number . . . . . . . . . . . . . . . . . . 23
Store a number from the call log . . . . . . . . . . . . 23
Delete from the call log . . . . . . . . . . . . . . . . . 24
Redial . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Review redial . . . . . . . . . . . . . . . . . . . . . . 25
Store a number from redial to the directory . . . . . . . 25
Dial a number from redial . . . . . . . . . . . . . . . 26
www.vtechphones.com
ii
Table of contents
Delete from redial . . . . . . . . . . . . . . . . . . . . 26
Answering system operation . . . . . . . . . . . . . . 27
Message capacity . . . . . . . . . . . . . . . . . . . . 27
Activate the answering system . . . . . . . . . . . . . 28
Set number of rings . . . . . . . . . . . . . . . . . . . 28
Set telephone base date and time . . . . . . . . . . . 28
Set telephone base melody . . . . . . . . . . . . . . . 29
Set telephone base ringer volume . . . . . . . . . . . 29
Change personal identification number (PIN) . . . . . 30
Outgoing announcements . . . . . . . . . . . . . . . 31
Play the announcement . . . . . . . . . . . . . . . . 31
Record your own announcement . . . . . . . . . . . . 31
Delete your announcement . . . . . . . . . . . . . . . 32
Message playback . . . . . . . . . . . . . . . . . . . 32
Options during playback . . . . . . . . . . . . . . . . 32
Delete all messages . . . . . . . . . . . . . . . . . . . 32
Remote access . . . . . . . . . . . . . . . . . . . . . 33
Message window displays . . . . . . . . . . . . . . . 34
Handset and telephone base indicators . . . . . . . . 35
Handset light . . . . . . . . . . . . . . . . . . . . . . 35
Telephone base lights . . . . . . . . . . . . . . . . . . 35
Handset icons . . . . . . . . . . . . . . . . . . . . . . 35
Handset display screen messages . . . . . . . . . . . 36
Call log display messages . . . . . . . . . . . . . . . 37
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Important safety instructions . . . . . . . . . . . . . . 39
Troubleshooting . . . . . . . . . . . . . . . . . . . . . 40
Operating range . . . . . . . . . . . . . . . . . . . . . 50
Maintenance . . . . . . . . . . . . . . . . . . . . . . . 50
About cordless telephones . . . . . . . . . . . . . . . 51
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 51
FCC, ACTA and IC regulations . . . . . . . . . . . . . 53
The RBRC ® Seal . . . . . . . . . . . . . . . . . . . . 54
Technical specifications . . . . . . . . . . . . . . . . . 55
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
www.vtechphones.com
iii
Installation
Installation
Parts checklist
Remember to save your sales receipt and original packaging in case it is necessary to ship your
telephone for warranty service. Check to make sure the telephone package includes the following:
1. Quick start guide
2. Handsets
(2 for 6042/6043, 3 for 6052/6053)
2 for 6052/6053)
1. Quick start guide
2. Handsets
3. Telephone base
6. Charger adapters
(1 for 6042/6043, 2 for 6052/6053)
7. Base power adapter
8. Batteries
(2 for 6042/6043, 4. User’s manual
3 for 6052/6053)
5. Chargers
6. Charger adapters
9. Battery compartment covers
(2 for 6042/6043, 3 for 6052/6053)
10.Telephone line cord
7. Base power adapter
8. Batteries 9. Battery compartment covers 10. Telephone line cord
www.vtechphones.com
Basic operation
3. Telephone base
4. User’s manual
5. Chargers
(1 for 6042/6043, • To purchase
replacement
batteries, or obtain
a replacement
power adapter,
visit our website at
www.vtechphones.
com or call 1 (800) 595-9511. In Canada, go to
www.vtechcanada.
com or call 1 (800) 267-7377.
• For 6043 and
6053, the battery
compartment
covers are
attached to the
handsets.
Installation
Install handset battery
• If the handset will
not be used for a
long period of time,
remove the battery
to prevent possible
leakage.
• To purchase
replacement
batteries, visit our
website at www.
vtechphones.
com or call 1 (800) 595-9511.
In Canada, go to
www.vtechcanada.
com or call 1 (800) 267-7377.
• Remove battery compartment cover by pressing on the indentation and sliding it downwards (only
for 6043 and 6053).
• Align the two holes in the plug with the socket pins according to the color-coded label in the
battery compartment, then snap the plug into place.
• Place the battery into the compartment.
• Position the battery compartment cover and slide it upwards until it clicks into place.
• Put the handset in the telephone base or the charger to charge the new battery for at least 16
hours. The battery may have enough charge for short calls. For best performance, charge it for
at least 16 hours.
You can keep the battery charged by returning the handset to the telephone base or charger after
each use. When the battery power is fully depleted, a full recharge takes about 16 hours.
For further information on batteries, please see the Battery section on page 38.
color-coded label
www.vtechphones.com
Telephone base installation
Install the telephone base and the charger as shown below. Choose a location away from any electronic
equipment and appliances such as personal computers, computer routers, television sets, microwave
ovens, and refrigerators. Avoid excessive heat, cold, dust or moisture.
1. Plug the telephone line cord into a telephone wall jack.
2. Plug the power adapter into an electrical
outlet not controlled by a wall switch.
Basic operation
www.vtechphones.com
• Use only the
VTech batteries
and power
adapters (or
equivalent)
supplied with
this telephone.
To obtain a
replacement, visit
our website at
www.vtechphones.
com or call 1 (800) 595-9511.
In Canada, go to
www.vtechcanada.
com or call 1 (800) 267-7377.
• This power unit
is intended to be
correctly oriented
in a vertical or floor
mount position.
The prongs are not
designed to hold
the plug in place if
it is plugged into a
ceiling, under-thetable or cabinet
outlet.
Installation
Installation
Installation
Desk/table bracket installation
The telephone base comes with the desk/table bracket installed and ready for tabletop use.
To remove the bracket:
1. Push the bracket away from the telephone
base as shown below. Do not remove the
bracket by force to avoid breakage of
the tabs.
Dial type
To install the bracket:
1. Align the tabs of the bracket with the slots
at the bottom of the telephone base as
shown in the diagram.
2. Slide the bracket towards the center
of the telephone base until it clicks
into place.
If you have touch-tone service, your telephone is ready to use as soon as the battery is charged. If
you have pulse (rotary) service, the dial type must be changed. To change the dial type, see Dial type on page 12.
www.vtechphones.com
Installation
Installation
If you subscribe to DSL service
If you receive high speed internet through your telephone line (commonly referred to as DSL), and
you are experiencing interference during telephone conversations and/or your caller ID features are
not functioning properly, install a DSL filter to the telephone line between the telephone base and
the telephone wall jack. Contact your DSL provider for a DSL filter.
Basic operation
DSL filter (for
DSL users)
To single telephone jack (RJ11C)
Telephone line cord
www.vtechphones.com
Telephone settings
Handset layout
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Earpiece
/ (directory/volume)
(speakerphone)
/FLASH
Dialing keys (0-9,*,#)
REDIAL/PAUSE
Microphone
Handset display
MENU/SELECT
CID /
(caller ID/volume)
OFF/CLEAR
MUTE/REMOVE
INT (intercom)
1
8
2
3
4
9
10
11
5
6
7
www.vtechphones.com
12
13
Basic operation
Telephone settings
Telephone settings
Telephone base layout
1. CHARGE light
2. IN USE light
3.
/REPEAT
4. Message window
5. FIND HANDSET
6. Speaker
7. VOICEMAIL light
1
8. X/DELETE
2
3
9. VOLUME+/4
10. /SKIP
11. ANS ON/OFF
5
(answer on/off)
12. Microphone
13. NO. OF RINGS
14. ANNC (announcement)
15. /PLAY/STOP
6
7
8
9
10
11
12 13 14 15
www.vtechphones.com
Telephone settings
Date and time
• When entering
the date or time, if
the digit is single,
a zero must be
entered first (i.e.
if the time is 6:08,
you must enter
0608).
• If you have
more than one
handset, setting
the date and time
on one handset
will apply to all
other handsets.
• The ring melody
for the telephone
base is set
separately from
the handset ring
melody. See
page 29 to set the
telephone base
melody.
•
•
•
•
•
•
•
Press MENU/SELECT to display menu when in idle mode.
Press
or
to reach Date/Time. Press MENU/SELECT.
Use the keypad to set the year. Press MENU/SELECT.
Use the keypad to set the date. Press MENU/SELECT.
Use the keypad to set the time. Press
or
to select a.m. or p.m.
Press MENU/SELECT.
The screen displays Stored and you’ll hear a confirmation beep.
Ring melody
There are ten ring melodies for the handset to choose from.
• Press MENU/SELECT to display menu when in idle mode.
• Press
or
to reach Setup HS. Press MENU/SELECT.
• Press or to reach Ring melody. Press MENU/SELECT, and
a checkmark is shown next to the current ring melody.
• Press
or
to scroll through the choices and a sample of each
ring melody will be played.
• Press MENU/SELECT.
• The screen displays Stored and you’ll hear a confirmation beep.
YEAR
200\
DATE
\1/01
TIME
\2:12AM
RING MELODY
Ring volume
Melody 1
Melody 2
Stored
www.vtechphones.com
Ring volume
The handset ringer volume can be adjusted, there are five levels to
choose from.
• Press MENU/SELECT to display menu when in idle mode.
• Press
or
to reach Setup HS. Press MENU/SELECT.
• Press
or
to reach Ring volume. Press MENU/SELECT.
• Press
or
to scroll through the choices and a sample of each ring
volume will be played.
• Press MENU/SELECT to confirm selection. The screen displays
Stored and you’ll hear a confirmation beep.
You can adjust the ringer volume by pressing VOL+ /VOL- on the
telephone base when the telephone is ringing.
Battery low tone
The handset is preset to beep when the battery level is low.
• Press MENU/SELECT to display the menu when in idle mode.
• Press
or
to reach Setup HS. Press MENU/SELECT.
• Press
or
to reach Tones. Press MENU/SELECT.
• Press
or
to reach Battery low. Press MENU/SELECT.
• A checkmark is shown next to the current selection. Press
or
to choose On or Off.
• Press MENU/SELECT.
• The screen displays Stored and you’ll hear a confirmation beep.
www.vtechphones.com
• The handset will
not ring when the
ringer volume is at
the lowest setting.
A ringer off icon
will be displayed.
Tones
Handset name
Battery low
Out of Range
On
Off
• While the
telephone is
ringing, you
can temporarily
silence the ringer
by pressing
OFF/CLEAR or
MUTE/REMOVE.
The next call will
ring normally. A
ringer off icon
will be displayed.
• The volume of
the telephone
base ringer is set
separately from
the handset ringer.
See page 29 for
telephone base
ringer volume
settings.
Basic operation
Telephone settings
Telephone settings
Telephone settings
Out of range tone
• Press OFF/CLEAR
at anytime to return
to the previous
screen.
• Press and hold
OFF/CLEAR at
anytime to exit the
menu.
The handset will beep during a conversation when it is out of range from
the telephone base. This tone is preset to On.
• Press MENU/SELECT to display the menu when in idle mode.
• Press
or
to reach Setup HS. Press MENU/SELECT.
• Press
or
to reach Tones. Press MENU/SELECT.
• Press
or
to reach Out of Range. Press MENU/SELECT.
• A checkmark is shown next to the current selection. Press
or
to choose On or Off.
• Press MENU/SELECT.
• The screen displays Stored and you’ll hear a confirmation beep.
Out of Range
KEY BEEPS
On
Off
Key tone
The handset is preset to beep whenever any button is pressed.
• Press MENU/SELECT to display the menu when in idle mode.
• Press
or
to reach Setup HS. Press MENU/SELECT.
• Press
or
to reach Tones. Press MENU/SELECT.
• Press
or
to reach Key beeps. Press MENU/SELECT.
• A checkmark is shown next to the current selection. Press
or
to
select On or Off.
• Press MENU/SELECT.
• The screen displays Stored and you’ll hear a confirmation beep.
10
Tones
Handset name
www.vtechphones.com
Edit handset name
Press MENU/SELECT to display the menu when in idle mode.
Press
or
to reach Setup HS. Press MENU/SELECT.
Press
or
to reach Handset Name. Press MENU/SELECT.
Press MUTE/REMOVE to backspace and erase characters. Press and hold MUTE/REMOVE to delete the entire entry. Press * to alternate between uppercase and lowercase.
• Use the keypad to enter characters (see the chart on page 18.)
• Press MENU/SELECT.
• The screen displays Stored and you’ll hear a confirmation beep.
Handset name
Language
•
•
•
•
Language
To change the language for all screen displays:
• Press MENU/SELECT to display menu when in idle mode.
• Press
or
to reach Setup HS. Press MENU/SELECT.
• Press
or
to reach Language. Press MENU/SELECT.
• A checkmark is shown next to the current selection. Press
or
to choose the desired language.
• Press MENU/SELECT.
• The screen displays Stored and you’ll hear a confirmation beep.
www.vtechphones.com
ENTER NAME
HANDSET\
a
• A handset name
can be up to 14
characters only.
• Only handset
display screens
are affected by
the language
setting.
Language
Reset
11
Basic operation
Telephone settings
Telephone settings
Telephone settings
Dial type
• The clear voicemail
feature only turns
off the displayed
NEW VOICEMAIL
message and
VOICEMAIL light
on the telephone
base. It does not
delete your voicemail
message(s). Use
this feature when the
telephone indicates
there is voicemail
when you have none
or you have accessed
your voicemail from a
remote location (while
away from home). If
there is actually a new
voicemail message,
your local telephone
company will continue
to send a signal
which will cause the
NEW VOICEMAIL
message in the
handset and the
telephone base
VOICEMAIL light to
flash.
12
The dial type is preset to touch tone. If you have pulse (rotary) service,
the dial type must be changed.
• Press MENU/SELECT to display menu when in idle mode.
• Press
or
to reach Setup BS. Press MENU/SELECT.
• Press
or
to reach Dial type. Press MENU/SELECT.
• A checkmark is shown next to the current selection. Press
or
to choose between tone and Pulse.
• Press MENU/SELECT.
• The screen displays Stored and you’ll hear a confirmation beep.
Dial TYPE
Clr VoiceMail
TONE
Pulse
Clear voicemail
If you subscribe to voicemail services provided by your local telephone
company, NEW VOICEMAIL will appear on the handset display and
the VOICEMAIL light on the telephone base will flash when you have
a new voicemail message. This feature allows you to turn off these
indicators.
• Press MENU/SELECT to display the menu when in idle mode.
• Press
or
to reach Setup BS. Press MENU/SELECT.
• Press
or
to reach Clr VoiceMail. Press MENU/SELECT.
• The screen displays Indicator off? Press MENU/SELECT.
• The screen displays Stored and you’ll hear a confirmation beep.
www.vtechphones.com
Clr VoiceMail
Reset
Indicator off?
Reset to default settings
The handset and the telephone base can be individually reset to their
default settings by selecting RESET in the SETUP HS or SETUP BS
menus respectively.
• Press MENU/SELECT to display menu when in idle mode.
• Press
or
to reach Setup HS or Setup BS. Press
MENU/SELECT.
• Press
or
to reach Reset. Press MENU/SELECT.
• The screen displays Reset? Press MENU/SELECT to confirm or
OFF/CLEAR to exit to the previous menu.
• The screen displays Stored and you’ll hear a confirmation beep.
Reset
RING MELODY
Reset?
• When the handset
or telephone base
settings are reset
to default, all items
stored in memory
will be deleted.
This includes the
directory and call
log entries.
Temporary tone dialing
If you have pulse (rotary) service, you can change from pulse to touch
tone dialing during a call by pressing * TONE. This is useful if you need
to send touch tone signals for access to telephone banking or long
distance services.
• Press
/FLASH.
• Press * TONE. Buttons pressed after this send touch tone signals.
• Dial the number.
• After hanging up, the telephone automatically returns to pulse dial
service.
www.vtechphones.com
13
Basic operation
Telephone settings
Telephone settings
Basic operation
Make, answer and end calls
• Press
or to
adjust the listening
volume during a
conversation.
• Press
/FLASH or
, then use the keypad to dial a number. -OR• Dial a number (press MUTE/REMOVE to make corrections) and then press
/FLASH or
.
• Press
/FLASH,
or any dialing keys (0-9, * or #) to answer an
incoming call.
• Press OFF/CLEAR or put the handset back to the telephone base or
charger to end a call.
• The call timer will be activated during a call to show call duration.
Options while on calls
Speakerphone
• Press
to alternate between speakerphone and normal handset use.
Mute
• Press MUTE/REMOVE on the handset to silence the microphone during a
conversation. You can still hear the caller but the caller cannot hear you.
• The screen displays MUTE.
• Press MUTE/REMOVE again to resume conversation.
Call waiting
If you subscribe to call waiting service and you are on a call when a new call
comes in, you will hear a beep. The caller ID information will be displayed
if you subscribe to caller ID service from your local telephone company.
• Press
/FLASH on the handset to answer the incoming call and put
the current call on hold.
• Press
/FLASH at anytime to alternate between calls.
14
www.vtechphones.com
PHONE
00:00:10
595-9511
MUTE
Basic operation
Intercom call
This feature allows conversation between handsets.
iNTERCOM
Number
• Press INT on a handset and its screen displays Number.
• Use the keypad to select a destination handset. The screen of the
orignating handset displays CALLING HANDSET X.
• The destination handset rings and its screen displays calling from: HANDSET X.
• Press
/FLASH,
or any dialing keys (0-9, * or #) on the destination CALLING
handset to answer the call.
HANDSET X
• To end an intercom call, press OFF/CLEAR on the handset or by placing
the handset back on the telephone base or charger.
While on a call, the person on the other handset can join the conversation.
• Press
/FLASH or
to join the conversation. (Only two handsets can
join the conference conversation at the same time.)
• Press OFF/CLEAR, or place the handset in the telephone base or charger
to drop out of the call. The external call will not be terminated until both
handsets hang up.
Basic operation
CALLING FROM:
Multiple handset use
• For 6042/6043,
press INT to
directly call the
other handset. It
is not necessary
to press any
number key.
HANDSET X
CONF
00:02:48
Answer an external call during an intercom call
There will be an alert tone to signify an incoming external call during an
intercom call and the screen displays CALL WAITING.
• Disconnect the intercom call by pressing OFF/CLEAR and the handset
will ring.
• Press
/FLASH,
or any dialing keys (0-9, * or #) to answer the
incoming call.
www.vtechphones.com
15
Basic operation
Transfer an external call
• If the destination
handset does not
answer, press
OFF/CLEAR on
the originating
handset to return
to the external
call.
• Press and hold
FIND HANDSET
to page handsets
while listening to
messages.
An external call can be forwarded to another handset during a conversation.
• Press INT and put the call on hold on the originating handset.
• Use the keypad to select the destination handset and the screen displays
CALLING Handset X. (For 6052/6053 only)
• The destination handset rings and its screen displays
CALLING FROM: HANDSET X.
• After the destination handset is answered, press MENU/SELECT and
then press
or
to reach conference.
• Press MENU/SELECT to let the destination handset join the
conversation.
• Press MENU/SELECT and the screen displays END CONFERENCE and
then press MENU/SELECT to return to the intercom conversation.
• During the intercom conversation, press MENU/SELECT and use
or
to reach OTHER CALL to return to the external call and put the intercom on
hold. Repeat this step to switch between the external and intercom call.
• Press OFF/CLEAR on the originating handset to forward the external call
to the destination handset.
Conference
OTHER CALL
OTHER CALL
CONFERENCE
END CONFERENCE
Find handset
• Press FIND HANDSET on the telephone base to locate the handset when
in idle mode. All handsets will ring and Paging will flash on the screen
of all handsets.
• Press FIND HANDSET again or put the handsets back on the telephone
base or charger to stop the paging tone.
16
www.vtechphones.com
PAGING
Advanced operation
Directory
The directory can store up to 50 entries. Each entry may consist of a
number up to 24 digits and a name up to 15 characters.
• The screen displays Empty if there is no record in the directory.
• The screen displays Full if the directory is full.
Review the directory
DIRECTORY
CALL LOG
• If more than 24
digits are entered
when storing
a telephone
number, there will
be an error tone.
Advanced operation
• Press
/ to enter the directory.
• Press
or
to browse and press OFF/CLEAR to exit.
-OR• Press MENU/SELECT to display menu when in idle mode.
• Press
or
to reach directory. Press MENU/SELECT.
• Press
or
to reach REVIEW. Press MENU/SELECT.
• Press
or
to browse and press OFF/CLEAR to exit.
Empty
REVIEW
STORE
Search the directory
Entries are sorted alphabetically and names beginning with numbers
are listed first.
An alphabetical search can be done after entering the directory. Enter
the first letter of the name using the chart on page 18. The first name
beginning with that letter will be displayed.
For example, press 5 (JKL) once to find Jenny, twice to find Kristen, or
three times to find Linda.
-ORYou can search the directory by pressing
or
on the handset.
www.vtechphones.com
VTECH
1-595-9511
17
Advanced operation
Chart of characters
• Press *
repeatedly to
alternate between
uppercase
and lowercase
when entering
characters.
Use the keypad and the chart below to enter a name (up to 15 characters). Each press of a particular
key causes the characters to be displayed in the following order:
Number Characters by number of key presses
key
1
2
3
4
5
6
7
8
9
1
space
1
*
?
!
/
(
)
2
A
B
C
2
3
D
E
F
3
4
G
H
I
4
5
J
K
L
5
6
M
N
O
6
7
P
Q
R
S
7
8
T
U
V
8
9
W
X
Y
Z
9
0
0
Uppercase/lowercase
*
,
#
#
,
-
.
&
• Press MUTE/REMOVE to backspace and erase a single character.
• Press and hold MUTE/REMOVE to delete the entire entry.
• Press and hold REDIAL/PAUSE to insert a dialing pause (P is displayed) when entering a
telephone number.
18
www.vtechphones.com
Advanced operation
Store an entry in the directory
• Press MENU/SELECT twice to enter the DIRECTORY.
• Press
or
to reach STORE and then press MENU/SELECT.
• The screen displays ENTER Number. Use the keypad to enter the
number and then press MENU/SELECT.
• The screen displays ENTER Name. Use the keypad to enter the
characters and then press MENU/SELECT.
• The screen displays Stored and you’ll hear a confirmation beep.
• Press
/ to enter the directory.
• Press
or
to scroll to the desired entry, or use the alphabetical
search to find it.
• Press
/FLASH or
to dial.
-OR• Press MENU/SELECT to display menu when in idle mode.
• Press
or
to reach directory. Press MENU/SELECT.
• Press
or
to reach REVIEW. Press MENU/SELECT.
• Press
or
to scroll to the desired entry, or use the alphabetical
search to find it.
• Press
/FLASH or
to dial.
www.vtechphones.com
enter Number
Advanced operation
Dial a directory entry
STORE
REVIEW
ENTER NAME
a
STORED
19
Advanced operation
Edit an entry in the directory
• Press OFF/CLEAR
to return to the
previous screen.
Press and hold
OFF/CLEAR to exit
the menu if you do
not want to delete
all the entries.
• Press
/ or MENU/SELECT three times to enter the directory.
• Press
or
to scroll to the desired entry or use the alphabetical
search to find the number. Press MENU/SELECT.
• The screen displays Enter number. Use MUTE/REMOVE and the
keypad to edit the number and press MENU/SELECT.
• The screen displays ENTER NAME. Use MUTE/REMOVE and the
keypad to edit the name and then press MENU/SELECT.
• The screen displays Stored and you’ll hear a confirmation beep.
Delete one or all entries in the directory
• Press
/ or MENU/SELECT three times to enter the directory.
• Press
or
to scroll to the desired entry.
To delete an entry
• Press MUTE/REMOVE.
• The screen displays Deleted and there is a confirmation beep.
To delete all entries
• Press and hold MUTE/REMOVE.
• The screen displays Delete All? Press MENU/SELECT.
• The screen displays Deleted and you’ll hear a confirmation beep.
enter Number
ENTER NAME
a
STORED
Deleted
Delete all?
20
www.vtechphones.com
Advanced operation
About caller ID information
If you subscibe to caller ID service from your local telephone company, this feature displays the name
and telephone number of the caller before answering a call (even when you are on another call). The
caller ID features of this product will work only if you subscribe to caller ID service and both you and
the caller are in areas offering caller ID service, and if both telephone companies use compatible
equipment.
Advanced operation
Contact your local telephone company if:
• you have both caller ID and call waiting, but as separate services (you may need combined service),
• you have only caller ID service, or only call waiting service,
• you do not subscribe to caller ID or call waiting services but wish to try them.
There may be fees for these services, and they may not be available in all areas.
This product can be used without subscribing to either caller ID or combined caller ID with call waiting
service, although the caller ID features of this product will not function.
www.vtechphones.com
21
Advanced operation
Call log
• Due to regional
service differences,
the caller ID
information may
not be available
for every incoming
call. In addition,
the callers may
intentionally block
their name and/or
telephone number.
• The time is
automatically set
and updated with
incoming caller ID
information if you
subscribe to this
service.
The information of the caller will be displayed if you subscribe to caller
ID service from your local tephone company.
• The call log can store up to 50 entries.
• Each entry may consist of a number up to 20 digits and a name up to
15 characters. If the number consists of more than 20 digits, the last 20
digits will be displayed and stored. If the name consists of more than
15 characters, the first 15 characters will be displayed and stored.
• Entries are displayed in chronological order with the newest entry
first.
• When the call log is full, the oldest entry will be deleted to make room
for the new incoming call information.
• The screen displays Empty if there is no record in the call log.
• The screen displays New if there are new call log entries (missed
and unread calls).
• Duplicate or anonymous calls (no caller ID information) will be stored
in the call log.
Review the call log
• Press CID/ to enter the call log.
-OR• Press MENU/SELECT. Press
or
to select Call log.
• Press MENU/SELECT and then press
or
to browse through the
entries.
• The name (if available), number, date and time of the incoming call
are displayed on the screen.
22
www.vtechphones.com
Johnny Fu
2-345-6789
NEW
05:27pm
11/23
Empty
Advanced operation
Dial a call log number
• Press CID/ to enter the call log.
-OR• Press MENU/SELECT. Press
or
to select Call log.
• Press MENU/SELECT and then press
or
to scroll to the desired
entry.
• Press
/FLASH or
to dial.
• Press CID/ to enter the call log.
-OR• Press MENU/SELECT. Press
or
to select Call log.
• Press MENU/SELECT and then press
or
to scroll to the desired
entry.
• Press MENU/SELECT and the screen displays ENTER NAME.
• Use the keypad to enter the name and then press MENU/SELECT.
• The screen displays Stored and you’ll hear a confirmation beep.
www.vtechphones.com
a
stored
• While reviewing
the call log, press
# repeatedly to
display the other
dialing options.
The available
options are: (1
+ area code +
number, area code
+ number, 1 +
number, number
only). The various
dialing options are:
595-9511
1-595-9511
800-595-9511
1-800-595-9511
23
Advanced operation
Store a number from the call log
enter name
Advanced operation
Delete one or all entries in the call log
• Press OFF/CLEAR
to return to the
previous screen.
Press and hold
OFF/CLEAR to exit
the menu if you do
not want to delete
all the entries.
24
• Press CID/ to enter the call log.
-OR• Press MENU/SELECT. Press
or
Deleted
to select Call log.
To delete one entry
• Press
or
to scroll to the desired entry and then press
MUTE/REMOVE.
• The screen displays DeleteD and you’ll hear a confirmation beep.
To delete all entries
• Press and hold MUTE/REMOVE when in the Call log.
• The screen displays Delete All? Press MENU/SELECT.
• The screen displays Deleted and you’ll hear a confirmation beep.
www.vtechphones.com
Delete all?
Advanced operation
Redial
The redial list can store up to 10 of the most recently dialed numbers.
• When there are already 10 entries in the redial list, the oldest entry
will be deleted to make room for the new one.
• The screen displays Empty if there is no record on the list.
Review redial
• Press REDIAL/PAUSE to enter the redial list.
• Press
or
to browse through the entries.
Advanced operation
Store a number from redial to the directory
•
•
•
•
•
Press REDIAL/PAUSE to enter the redial list.
Press
or
to scroll to the desired entry. Press MENU/SELECT.
The screen displays enter Name.
Use the keypad to enter the name and then press MENU/SELECT.
The screen displays Stored and there is a confirmation beep.
www.vtechphones.com
25
Advanced operation
Dial a number from redial
• Press OFF/CLEAR
to return to the
previous screen.
Press and hold
OFF/CLEAR to
exit the menu if
you do not want
to delete all the
entries.
• Press REDIAL/PAUSE to enter the redial list.
• Press
or
to scroll to the desired entry.
• Press
/FLASH or
to dial.
Delete one or all entries from redial
• Press REDIAL/PAUSE to enter the redial list.
To delete one entry
• Press
or
to scroll to the desired entry and then press
MUTE/REMOVE.
• The screen displays DeleteD and you’ll hear a confirmation beep.
To delete all entries
• Press and hold MUTE/REMOVE.
• The screen displays Delete All? Press MENU/SELECT.
• The screen displays Deleted and you’ll hear a confirmation beep.
26
www.vtechphones.com
Deleted
Delete all?
Answering system operation
Message capacity
The answering system can record up to 99 messages, depending on the length of each message.
The total maximum recording time is 15 minutes and each individual message can be up to four
minutes long. Messages will remain available for replay until they are deleted.
X/DELETE
Press to delete message currently playing.
When idle, press and hold to delete all
messages (page 32).
/REPEAT
/SKIP
Press to skip to next
message (page 32).
Message window
Pr e s s to a d j u s t vo l u m e
during playback (page 32).
Press to adjust call
screening volume (page 32).
Press to adjust ringer
volume while the telephone
is ringing (page 29).
Advanced operation
Press to repeat a message
(page 32).
/ /VOLUME+/-
Shows the status and
number of messages
(page 34).
/PLAY/STOP
Press to play or stop playing
messages (page 32).
ANS ON/OFF
Press to turn on or off the
answering system (page 28).
ANNC
Press to play or record the outgoing
announcement (page 31).
www.vtechphones.com
27
Answering system operation
Activate the answering system
• When ANS ON/OFF
is turned off, your
telephone will ring
10 times before
answering and
prompting for the
remote access
code.
The ANS ON/OFF must be on (the button light will be on) in order for the
machine to answer calls and record messages. If the button light is off then
calls will not be answered.
To turn on/off the answering system, press ANS ON/OFF to choose between
on and off.
Use the volume control button on the telephone base to adjust the volume
at anytime during the setup procedure.
Set number of rings
This feature allows you to select the number of times the telephone rings before the answering system
answers. You can choose from two, four, six, eight rings or toll saver. When toll saver is activated, the
answering system answers after two rings when there are new messages, and after six rings when
there are no new messages.
• Press NO. OF RINGS when in idle mode and the system announces the current setting.
• The system announces “To change the setting, press number of rings again.”
• Press NO. OF RINGS repeatedly until the desired setting is announced. If you do not press the
ANNC button for about two seconds, the setting will be saved and there is a confirmation beep.
Set telephone base date and time
The answering system announces the day and time the message was received before playing each
message. Set the date and time before using the answering system so all messages are dated correctly.
Setting handset date and time will simultaneously update the telephone base date and time.
The system will announce “ Please set the handset clock” before message playback if you do not set
the date and time before using this system.
28
www.vtechphones.com
Answering system operation
Set telephone base melody
Set telephone base ringer volume
You can adjust the telephone base ringer volume to one of eight different
levels, or turn the telephone base ringer off.
• Press MENU/SELECT on the handset in idle mode.
• Press
or
to reach Setup BS. Press MENU/SELECT.
• Press
or
to reach bs ringer vol. Press MENU/SELECT.
• Press
or
to scroll through the choices and a sample of each ring
volume will be played at the telephone base.
• Press MENU/SELECT to confirm selection.
• The screen displays Stored and you’ll hear a confirmation beep.
You can also adjust the telephone base ringer volume by pressing VOL+/on the telephone base while the telephone is ringing.
www.vtechphones.com
Setup BS
Date/Time
BS Melody
BS RINGER VOL
Melody 1
Melody 2
• The ring melody
for the handset
is set separately
from the telephone
base ring melody.
See page 8 to set
the handset ringer
melody.
• The volume of the
handset ringer
is set separately
from the telephone
base ringer. See
page 9 to change
the handset ringer
volume.
29
Advanced operation
There are six ring melodies to choose from.
• Press MENU/SELECT on the handset to display menu when in idle
mode.
• Press
or
to reach Setup BS. Press MENU/SELECT.
• Press
or
to reach BS melody. Press MENU/SELECT and a
checkmark is shown next to the current melody.
• Press
or
to scroll through the choices and a sample of each
melody will be played on the telephone base.
• Press MENU/SELECT to confirm selection.
• The screen displays Stored and you’ll hear a confirmation beep.
Answering system operation
Change personal identification number (PIN)
A four-digit security code is required for remote access to the answering
system from any touch tone telephone. The factory default code is 0000.
To change the PIN on your telephone:
• Press MENU/SELECT on the handset in idle mode.
• Press
or
to reach Setup BS. Press MENU/SELECT.
• Press
or
to reach CHANGE ITAD PIN. Press MENU/SELECT.
• The screen displays Enter PIN.
• Enter the PIN (default 0000) then press MENU/SELECT.
• The screen displays New PIN.
• Enter the desired PIN and press MENU/SELECT.
• The screen displays Repeat PIN.
• Enter the new PIN again and press MENU/SELECT.
• The screen displays Stored and you’ll hear a confirmation beep.
• If a wrong PIN is entered, the screen displays WRONG PIN, retry
after two seconds.
Change ITAD PIN
Dial type
Enter PIN
Enter PIN
****
NEW PIN
REPEAT PIN
30
www.vtechphones.com
Answering system operation
Outgoing announcements
An outgoing announcement is the message callers hear when calls are
answered by the answering system.
The telephone is preset with an announcement that answers calls with
“Hello, please leave a message after the tone.” You can use this default
announcement, or replace it with your own.
Play the announcement
Record your own announcement
• Press ANNC in idle mode, and the system announces “Announcement, press
play or press announcement again to record a new announcement.”
• Press ANNC again and the system announces “Record after the tone,
press stop when you are done.”
• After the tone, speak towards the microphone at the bottom front of the
telephone base from about nine inches away.
• Press /PLAY/STOP when finished.
• The answering system will automatically playback the newly recorded
announcement and there will be a confirmation tone. Press
/PLAY/
STOP to stop the playback at any time.
• If you do not like the announcement just recorded, press ANNC to record
again before the confirmation tone.
www.vtechphones.com
31
Advanced operation
• Press ANNC in idle mode. The system announces “Announcement, press
play or press announcement again to record a new announcement.”
• Press PLAY/STOP and the announcement will be played.
• The annoucement
can be up to 90
seconds in length.
• When your
own recorded
annoucement
is deleted, calls
will be answered
with the preset
announcement.
Answering system operation
Delete your announcement
• Messages can
only be deleted
after they are
played.
• When the
answering
machine is
recording
an incoming
message or in
idle mode, the call
screening volume
can be adjusted
by pressing
VOL+/- on the
telephone base.
• Press ANNC in idle mode, and the system announces “Announcement,
press play or press announc ement again to rec ord a new
announcement.”
• Press
/PLAY/STOP and then press DELETE when the system
is playing the outgoing announcement. The system announces
“Announcement deleted.”
Message playback
• Press /PLAY/STOP to listen to messages. Press /PLAY/STOP
again to stop playback.
• If there are new messages, the system will announce the number of
new and old messages then play the new messages only (oldest first).
If there are no new messages, the system will announce the number
of old messages and playback all messages (oldest first).
• Before each message is played, the day and time it was received will
be announced.
Options during playback
•
•
•
•
Press / /VOLUME to adjust the speaker volume.
Press /SKIP to skip to the next message.
Press /REPEAT to repeat the message currently playing.
Press X/DELETE to delete the current message. The system will
advance to the next message.
Delete all messages
• Press and hold X/DELETE when in idle mode.
• The system announces “All old messages deleted.”
32
www.vtechphones.com
Answering system operation
Remote access
You can access many features of your answering system remotely from any touch tone telephone.
A four-digit security code is required to access the system and the factory default code is 0000; see
page 30 to change it. To enter remote access:
• Dial your telephone number from any touch tone telephone.
• When the system answers and plays the outgoing announcement, press
followed by the
*
remote access code.
• After you enter the remote access code, the system will play any new messages and then play
the menu of commands.
• During remote
access, if no key
is pressed within
eight seconds,
the remote
access call is
automatically
disconnected.
Advanced operation
Remote access commands:
0
To end the call
1
To play all messages
2
To play new messages
3
To delete the message
33
To delete all old messages
4
To repeat the previous message
5
To stop playing the message
6
To skip the message
7
To turn the answering system on
8
To turn the answering system off
9
To repeat help
www.vtechphones.com
33
Answering system operation
Message window displays
The message counter usually displays the total number of incoming messages.
See the list below for explanations of other displays in this counter.
34
0
No messages.
0 (flashing)
The clock needs to be set.
1-99
Total number of old message(s) recorded.
1-99 (flashing)
Total number of message(s) recorded, at least one is new.
1-99 & F (alternating)
Memory is full with total number of messages recorded.
1-90 (counting)
Elapsed time while recording an annoucenment.
1-99
Current message number during message playback.
0-8
Current volume level while adjusting.
02, 04, 06, 08, tS
Current number of rings while setting.
--
System is answering a call.
-- (flashing)
System is being setup or initialized, or being accessed remotely.
www.vtechphones.com
Handset and telephone base indicators
Handset light
• On when the handset speakerphone is in use.
Telephone base lights
IN USE
• Flashes when there is an incoming call.
• Flashes when another handset connected to the same line is in use.
• On when the handset is in use.
VOICEMAIL
• Flashes when there is a new network message (a subscription service
from your local telephone company is required).
CHARGE
• On when the handset is in the telephone base.
ANS ON/OFF
• On when the answering system is on.
Handset icons
• Ringer off.
• Cycles (low, medium, and full) when handset battery is charging.
• Flashes when the battery power is low.
www.vtechphones.com
35
Appendix
(Battery indicator)
Handset display screen messages
Display:
When:
CALL
There is an incoming call.
CALLING HANDSET X
Calling another handset.
CALLING FROM: HANDSET X
Other handset is calling.
CHARGING
A handset with low battery has been placed on the telephone base to
recharge.
CONNECTING...
The cordless handset is searching for the telephone base.
EMPTY
There are no entries in the call log, directory, or redial list.
ENDED
You have just ended a call.
FULL
The directory is full.
INTERCOM
The handset is on an intercom call.
LINE IN USE
Another handset connected to the same line is in use.
LOW BATTERY
The battery needs to be recharged.
MUTE
The microphone is muted temporarily during a conversation.
NEW
There are un-reviewed calls in the call log.
NEW VOICEMAIL
There is new voicemail message.
NOT AVAILABLE
There is no line or the handset is out of range from the telephone base.
-ORIf one handset is already viewing the call log and another handset
attempts to review it.
NO LINE
There is no telephone line connected.
36
www.vtechphones.com
Handset display screen messages
Display:
PAGING
When:
The handset locator has been activated or the handset is being paged.
PHONE
The handset is in use.
PLACE IN CHARGER
The battery is very low. The handset should be placed on the telephone
base to recharge.
WARNING
The battery is not installed or not installed properly in the handset.
-OR The battery needs to be replaced.
-OR An incorrect battery has been installed by mistake. Use only the
supplied VTech battery, or equivalent.
CHECK BATTERY!
Call log display messages
When:
PRIVATE NAME
The caller is blocking name information.
PRIVATE NUMBER
The caller is blocking telephone number information.
PRIVATE CALLER
The caller is blocking name and number information.
UNKNOWN NAME
This caller’s name is unavailable.
UNKNOWN NUMBER
This caller’s number is unavailable.
UNKNOWN CALLER
No call information is available about this caller.
LONG DISTANCE or
This is a long distance call.
L (before caller’s number)
www.vtechphones.com
37
Appendix
Display:
Battery
After the battery is fully charged for 16 hours, you can expect the following performance:
Operation
Operating time
While in use (talking)
10 hours
While not in use (standby*)
100 hours
*Handset is off the telephone base but not in use.
The battery needs charging when:
• A new battery is installed in the handset.
• Battery indicator on screen is flashing.
CAUTION:
1. Use only the supplied battery (part number 89-1326-00-00) or equivalent. To order a replacement, visit our website at
www.vtechphones.com or call 1 (800) 595-9511. In Canada, visit www.vtechcanada.com or call 1 (800) 267-7377.
2. Do not dispose of the battery in a fire. Check with local waste management codes for special disposal instructions.
3. Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may cause burns or injury to the eyes or
skin. The electrolyte may be toxic if swallowed.
4. Exercise care in handling batteries in order not to create a short circuit by letting them come into contact with conductive
materials such as rings, bracelets, and keys. The battery and/or conductor may overheat and cause burns.
5. Charge the battery(ies) provided with or identified for use with this product only in accordance with the instructions and
limitations specified in this manual.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO WATER OR ANY TYPE OF MOISTURE.
38
www.vtechphones.com
Important safety instructions
When using your telephone equipment, basic safety precautions should always be followed:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water (for example, near a bathtub, kitchen sink, or swimming pool).
5. Do not place this product on an unstable surface such as a table, shelf or stand. This product may fall, causing serious damage.
6. Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation. To protect them from overheating, these openings must not be
blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This product should
not be placed in an area where proper ventilation is not provided.
7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your
dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not install this product where the cord may be walked on.
9. Never push objects of any kind into this product through slots in the telephone base or handset as they may touch dangerous voltage points or create a short circuit that could
result in a risk of fire or electric shock. Never spill liquid of any kind on the product.
10. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the telephone base or handset other
than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.
11. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
12. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled onto the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operation instructions, as improper adjustment of other controls may result in damage and often requires extensive work by an authorized technician to restore the product to normal operation.
E. If the product has been dropped and the telephone base and/or handset has been damaged.
F. If the product exhibits a distinct change in performance.
13. The power unit is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, an
under-the-table or cabinet outlet.
14. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric shock from lightning.
15. Do not use the telephone to report a gas leak in the vicinity of the leak.
16. Only put the handset of your telephone next to your ear when it is in normal talk mode.
SAVE THESE INSTRUCTIONS
www.vtechphones.com
39
Appendix
CAUTION: Use only the power adapter provided with this product. To purchase, visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to
www.vtechcanada.com or call 1 (800) 267-7377.
Troubleshooting
If you have difficulty with your telephone, please try the suggestions below. For Customer Service, visit our website at www.
vtechphones.com, or call 1 (800) 595-9511; in Canada, call 1 (800) 267-7377.
Problem
Suggestion
My telephone does not
work at all.
• Make sure the battery is installed and charged correctly (page 2). For optimum daily
performance, return the cordless handset to the telephone base or charger after use.
• Make sure the power adapter is securely plugged into an outlet not controlled by a wall
switch.
• Make sure the telephone line cord is plugged firmly into the telephone base and the wall jack.
• Unplug the unit’s electrical power. Wait for approximately 15 seconds, then plug it back in.
Allow up to one minute for the cordless handset and telephone base to synchronize.
• Charge the battery in the cordless handset for at least 16 hours.
• Remove and re-insert the battery. If that still does not work, it may be necessary to purchase
a new battery.
• Disconnect the telephone base from the jack and plug in a working telephone. If this telephone
does not work, the problem is probably in the wiring or the local service. Call the local telephone
company.
Low Battery is
displayed on screen.
• Place the handset in the telephone base or charger for recharging.
• Remove and re-install the battery and use it normally until fully discharged, then recharge the
handset on the telephone base or charger for 16 hours.
• If the above measures do not correct the problem, the battery may need to be replaced.
40
www.vtechphones.com
Troubleshooting
Problem
Suggestion
The battery does not
charge in the handset
or the handset battery
does not accept
charge.
• Make sure the handset is placed in the telephone base or charger correctly. The CHARGE
light on the telephone base or charger should be on.
• Remove the battery from the handset and then re-install it in the handset. Put the handset
back to the telephone base or charger and charge for 16 hours.
• If the cordless handset is in the charger or in the telephone base but the CHARGE light is not
on, see The charge light is off in this section.
• It may be necessary to purchase a new battery. Please see the Battery section of this user’s
manual (page 38).
• The telephone might be malfunctioning. Please see the Warranty section of this user’s manual
(page 51) for further instruction.
The CHARGE light is
off.
• Clean the charging contacts on the cordless handset(s) and telephone base each month using
a pencil eraser or a dry non-abrasive fabric.
• Make sure the power adapter and telephone line cords are plugged in correctly and
securely.
• Unplug the power adapter. Wait for 15 seconds before plugging it back in. Allow up to one
minute for the cordless handset and telephone base to reset.
• The telephone might be malfunctioning. Please see the Warranty section of this user’s manual
(page 51) for further instruction.
41
Appendix
www.vtechphones.com
Troubleshooting
Problem
Suggestion
There is no dial tone.
•
•
•
•
My handset displays
CONNECTING...
• Move the handset closer to the telephone base. You might have moved out of range.
My handset displays
NOT AVAILABLE
• Move the handset closer to the telephone base. You might have moved out of range.
• Make sure no other handset is reviewing the call log when an attempt is denied.
42
First, try all the above suggestions.
Move the cordless handset closer to the telephone base. It might be out of range.
The telephone line cord might be malfunctioning. Try installing a new telephone line cord.
Disconnect the telephone base from the telephone jack and connect a different telephone. If
there is no dial tone on the other telephone either, the problem is in your wiring or local service.
Contact your local telephone company.
www.vtechphones.com
Troubleshooting
Problem
Suggestion
The telephone does
not ring when there is
an incoming call.
• Make sure the ringer is on (see page 9 for handset and page 29 for telephone base).
• Make sure the telephone line cord and power adapter are plugged in properly (page 3).
• The cordless handset may be too far from the telephone base. Move it closer to the telephone
base.
• There may be too many extension telephones on the telephone line to allow all of them to ring
simultaneously. Try unplugging some of them.
• If the other telephones in your home are having the same problem, the problem is in the wiring
or local service. Contact the local telephone company (charges may apply).
• Other electronic products can cause interference to your cordless telephone. Try installing your
telephone as far away as possible from the following electronic devices: wireless routers, radios,
radio towers, pager towers, cellular telephones, digital telephones, intercoms, room monitors,
televisions, VCRs, personal computers, kitchen appliances, and other cordless telephones.
• Test a working telephone at the telephone jack. If another telephone has the same problem, the
problem is in the telephone jack. Contact your local telephone company (charges may apply).
• The telephone line cord might be malfunctioning. Try installing a new telephone line cord.
• Remove and re-insert the battery and place the cordless handset in the telephone base.
• Wait for the cordless handset to synchronize with the telephone base. Allow up to one minute
for this to take place.
43
Appendix
www.vtechphones.com
Troubleshooting
Problem
Suggestion
I cannot dial out.
• First, try all the above suggestions.
• Make sure there is a dial tone before dialing. It is normal if the cordless handset takes a second
or two to synchronize with the telephone base before producing a dial tone. Wait an extra
second before dialing.
• Make sure the telephone is set to the correct dial type (pulse dial or tone dial) for the service in
your area. See Dial type on page 12 to set the dial type.
• If the other telephones in your home are having the same problem, the problem is in the wiring
or local service. Contact your local telephone company (charges may apply).
• Eliminate any background noise. Noise from a television, radio, or other appliances may cause
the telephone not to dial out properly. If you cannot eliminate the background noise, first try
muting the cordless handset before dialing, or dialing from another room in your home with
less background noise.
44
www.vtechphones.com
Troubleshooting
Problem
Suggestion
There is noise
or interference
during a telephone
conversation.
• The handset may be out of range. Move it closer to the telephone base.
• Appliances or other cordless telephones plugged into the same circuit as the telephone base
can cause interference. Try moving the appliance or telephone base to another outlet.
• Other electronic products can cause interference to your cordless telephone. Try installing your
telephone as far away as possible from the following electronic devices: wireless routers, radios,
radio towers, pager towers, cellular telephones, digital telephones, intercoms, room monitors,
televisions, VCRs, personal computers, kitchen appliances, and other cordless telephones.
• If your telephone is plugged in with a modem or a surge protector, plug the telephone (or
modem/surge protector) into a different location. If this solves the problem, re-locate your
telephone or modem farther apart from each other, or use a different surge protector.
• The layout of your home or office might be limiting the operating range. Try moving the telephone
base to another location, preferably a higher location for better reception.
• Disconnect the telephone base from the modular jack and plug in a corded telephone. If calls
are still not clear, the problem is probably in the wiring or local service. Contact the local
telephone company (charges may apply).
• If the other telephones in your home are having the same problem, the problem is in the wiring
or local service. Contact the local telephone company (charges may apply).
• Do you have DSL service? If yes, you need to have a DSL filter installed at every telephone jack
that has a telephone connected to it. Contact your DSL service provider for filter information.
My calls cut in and out
when I am using the
cordless handset.
45
Appendix
www.vtechphones.com
Troubleshooting
Problem
Suggestion
I hear other calls when
using the telephone.
• Disconnect the telephone base from the telephone jack. Plug in a different telephone. If there are
still other calls, the problem is probably in the wiring or local service. Call your local telephone
company.
I hear noise in the
cordless handset, and
none of the keys or
buttons work.
• Make sure the telephone line cord is plugged in securely.
• Remove and re-insert the battery.
My caller ID features are
not working properly
• Caller ID is a subscription service. You must subscribe to this service from your local telephone
company for this feature to work on your telephone.
• The caller may not be calling from an area which supports caller ID.
• Both you and the caller’s telephone companies must use equipment which are compatible with
caller ID service.
• If you subscribe to DSL service, install a DSL filter to the telephone line between the telephone
base and the telephone line jack. Contact your DSL service provider for filter information.
46
www.vtechphones.com
Troubleshooting
Problem
Suggestion
The system does
not receive caller ID
or the system does
not display caller ID
during call waiting.
• Make sure you subscribe to caller ID with call waiting features provided by the local telephone
company.
• The caller may not be calling from an area which supports caller ID.
• Both you and the caller’s telephone companies must use equipment which are compatible with
caller ID service.
• If you subscribe to DSL service, install a DSL filter to the telephone line between the telephone
base and the telephone line jack. Contact your DSL service provider for filter information.
The answering system
does not answer after
the correct number of
rings.
• Make sure the answering system is on. When the answering system is on, the red light on the
ANSWER ON/OFF key should be lit.
• If toll saver is activated, the number of rings changes to two when there are new messages
waiting (see page 28).
• If the memory is full or if the answering system is off, the system will answer after ten rings.
• In some cases, the answering system will be affected by the ringing system used by the local
telephone company.
The announcement
message is not clear.
• When recording the announcement, make sure you speak in a normal tone of voice about nine
inches from the telephone base.
• Make sure there is no background noise (television, music, traffic, etc.) when recording.
47
Appendix
www.vtechphones.com
Troubleshooting
Problem
Suggestion
The answering system
does not record
messages.
• Make sure the answering system is on.
The messages on the
answering system are
incomplete.
• If a caller leaves a very long message, part of it may be lost when the system disconnects the
call after four minutes.
• If the caller pauses for more than five consecutive seconds, the system stops recording and
disconnects the call.
• If the memory on the system becomes full during a message, the system stops recording and
disconnects the call.
• If the caller’s voice is very soft, the system may stop recording and disconnect the call.
The messages on
the system are very
difficult to hear.
• Press
The answering system
does not respond to
remote commands.
• Make sure your remote access code is correct (page 33).
• Make sure you are calling from a touch-tone telephone. When dialing a number, there should
be tones. If there are clicks, then it is not a touch-tone telephone and cannot activate the
answering system.
• The answering system may not detect the remote access code when the announcement is
playing. Wait until the announcement is over before entering the code.
• There may be interference on the telephone line you are using. Press the keypad keys firmly
when dialing.
48
/
/VOLUME on the telephone base to increase the speaker volume.
www.vtechphones.com
Troubleshooting
Problem
Suggestion
My cordless handset
beeps and is not
performing normally.
• Make sure the power cord is securely plugged into the telephone base. Plug the unit into a
different working electrical outlet not controlled by a wall switch.
• Move the cordless handset closer to the telephone base. It may be out of range.
• Reset the telephone base by unplugging the unit’s electrical power. Wait for 15 seconds and
plug it back in again. Allow up to one minute for the cordless handset and the telephone base
to synchronize.
• Other electronic products can cause interference to your cordless telephone. Try installing
your telephone as far away from these electronic devices as possible: wireless routers, radios,
radio towers, pager towers, cellular telephones, intercoms, room monitors, televisions, personal
computers, kitchen appliances and other cordless telephones.
Common cure for
electronic equipment
• If the unit is not responding normally, try putting the cordless handset in the telephone base
or the charger. If it does not seem to respond, try the following (in the order listed):
• Disconnect the power to the telephone base.
• Disconnect the battery on the cordless handset.
• Wait a few minutes before connecting power to the telephone base.
• Re-install the battery and place the cordless handset into the telephone base or charger.
• Wait for the cordless handset to synchronize its connection with the telephone base. Allow up
to one minute for this to take place.
49
Appendix
www.vtechphones.com
Operating range
This cordless telephone operates with the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and telephone base can
communicate over only a certain distance ----which can vary with the locations of the telephone base and handset, the weather, and the layout of your home or office.
When the handset is out of range, the handset will display CONNECTING. The user can access the handset directory, and certain parts of the menu system, i.e.
handset setting, but not the time setting and telephone base setting. Not AVAILABLE will be displayed if access is denied.
If there is a call while the handset is out of range, it might not ring, or if it does ring, the call might not connect well when you press
/FLASH. Move closer to the
telephone base, then press
/FLASH to answer the call.
If the handset moves out of range during a telephone conversation, there might be interference.
To improve reception, move closer to the telephone base.
Maintenance
Taking care of your telephone
Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original packing materials to protect your telephone if you ever need to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with wet hands. Do not install the telephone base near a
sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety, take caution when using electric appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft cloth slightly dampened with water or a mild soap.
Do not use excess water or cleaning solvents of any kind.
Remember that electrical appliances can cause serious injury if used when you are wet or standing in water. If the telephone base should fall into water, DO NOT
RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL. Then pull the unit out by the unplugged cords.
50
www.vtechphones.com
About cordless telephones
•
•
•
•
•
Privacy: The same features that make a cordless telephone convenient create some limitations. Telephone calls are transmitted between the telephone base and
the cordless handset by radio waves, so there is a possibility that the cordless telephone conversations could be intercepted by radio receiving equipment within
range of the cordless handset. For this reason, you should not think of cordless telephone conversations as being as private as those on corded telephones.
Electrical Power: The telephone base of this cordless telephone must be connected to a working electrical outlet. The electrical outlet should not be controlled
by a wall switch. Calls cannot be made from the cordless handset if the telephone base is unplugged or switched off, or if the electrical power is interrupted.
Potential TV Interference: Some cordless telephones operate at frequencies that may cause interference to televisions and VCRs. To minimize or prevent
such interference, do not place the telephone base of the cordless telephone near or on top of a TV or VCR. If interference is experienced, moving the cordless
telephone farther away from the TV or VCR will often reduce or eliminate the interference.
Rechargeable Batteries: This product contains either Nickel-Cadmium or Nickel-Metal Hydride rechargeable batteries. Exercise care in handling batteries in
order not to create a short circuit with conducting material such as rings, bracelets, and keys. The battery or conductor may overheat and cause harm. Observe
proper polarity between the battery and the battery charger.
Nickel-Metal Hydride Rechargeable Batteries: Dispose of these batteries in a safe manner. Do not burn or puncture. Like other batteries of this type, if
burned or punctured, they could release caustic material which could cause injury.
Warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the Product and all accessories provided
in the sales package (“Product”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used
normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the
United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without charge, a Materially Defective Product. If
we repair the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of
the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive remedy.
VTech will return repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days.
www.vtechphones.com
51
Appendix
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under
the terms of this limited warranty, this limited warranty also applies to repaired or replacement Product for a period of either (a) 90 days from the date the repaired
or replacement Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect,
inundation, fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech accessories; or
Warranty
5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes
(including but not limited to Products used for rental purposes); or
7. Product returned without valid proof of purchase (see item 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.
How do you get warranty service?
To obtain warranty service in the United States of America, please call 1 (800) 595-9511; In Canada, please call 1 (800) 267-7377. NOTE: Before calling for service,
please review the user’s manual - a check of the Product controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges
incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty to you, transportation,
delivery or handling charges prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty,
or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further
repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty; and
2. Include “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other Limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product.
VTech provides no other warranties for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other
express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary
use) are limited to one year from date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation
may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost
profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use
of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you.
Please retain your original sales receipt as proof of purchase.
52
www.vtechphones.com
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission
(FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to
the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the user.
The telephone base shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance of approximately 20 cm (8 inches)
or more. If you choose to use a clipping device, please make sure to only use the supplied VTech belt clip.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2)
This device must accept any interference received, including interference that may cause undesired operation.
Privacy of communications may not be ensured when using this telephone.
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The
label on the back or bottom of this equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to
your local telephone company upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with applicable Part 68 rules and technical requirements
adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also
compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See Installation Instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called.
The REN for this product is encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas,
the sum of all RENs should be five (5.0) or less. For more information, please contact your local telephone company.
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only
be made by the manufacturer or its authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty.
www.vtechphones.com
53
Appendix
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
FCC, ACTA and IC regulations
If this equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your telephone service. The telephone company is
required to notify you before interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct
the problem and the telephone company is required to inform you of your right to file a complaint with the FCC. Your telephone company may make changes in its
facilities, equipment, operation, or procedures that could affect the proper functioning of this product. The telephone company is required to notify you if such changes
are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, fire, medical) in these locations. If you do store or
test emergency numbers, please:
• Remain on the line and briefly explain the reason for the call before hanging up.
• Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
This equipment complies with regulations RSS-213 and CS-03 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
The term ‘’IC: ‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of the maximum number of devices allowed to be connected to
a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the
devices does not exceed five.
This Class B digital apparatus complies with Canadian ICES-003.
The RBRC® Seal
The RBRC ® Seal on the nickel-metal-hydride battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada.
The RBRC ® program provides a convenient alternative to placing used nickel-metal-hydride batteries into the trash or municipal waste,which may be illegal in your area.
VTech’s participation in RBRC ® makes it easy for you to drop off the spent battery at local retailers participating in the RBRC ® program or at authorized VTech product service centers. Please call 1-800-8-BATTERYTM for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources.
RBRC ® is a registered trademark of Rechargeable Battery Recycling Corporation.
54
www.vtechphones.com
Technical specifications
Frequency control
Crystal controlled PLL synthesizer
Transmit frequency
Handset: 1921.536-1928.448 MHz
Telephone base: 1921.536-1928.448MHz
Channels
5
Nominal effective range
Maximum power allowed by FCC and IC. Actual operating range may vary according
to environmental conditions at the time of use.
Size
Handset: 170.9mm X 48.1mm X 25.8mm
Telephone base: 179.8mm X 123.8mm X 95.0mm
Charger: 84.0mm X 99.0mm X 102.0mm
Weight
Handset: 131.0 grams (including battery)
Telephone base: 296.8 grams
Charger: 101.4 grams
Power requirements
Handset: 2.4V DC 600mAh NiMH battery
Telephone base: 6V DC @ 600mA
Charger: 6V AC @300mA
Memory
Handset directory: 50 memory locations; up to 24 digits and 15 characters
Handset call log: 50 memory locations; up to 20 digits and 15 characters
55
Appendix
www.vtechphones.com
Index
A
About cordless telephones 51
Advanced operation 17
Answer an external call during an
intercom call 15
Answering system operation 27
B
Basic operation 14
Battery 9, 38
C
Call log 22, 37
Call waiting 14
Chart of characters 18
D
Date and time 8
Delete from redial 26
Delete from the call log 24
Delete from the directory 20
Delete your announcement 32
Desk/table bracket installation 4
Dial a number from redial 26
56
Dial type 4, 12
Directory 17
DSL filter 5
E
Edit an entry in the directory 20
Edit handset name 11
F
FCC, ACTA and IC regulations 53
Find handset 16
H
Handset display screen messages 36
Handset layout 6
I
Important safety instructions 39
Index 56-57
Installation 1
Install handset battery 2
Intercom call 15
Internet 4
www.vtechphones.com
M
Maintenance 50
Make, answer and end calls 14
Message capacity 27
Message playback 32
Message window displays 34
Multiple handset use 15
Mute 14
O
Operating range 50
Options while on calls 14
Outgoing announcements 31
P
Parts checklist 1
Play the announcement 31
R
Record your own announcement 31
Redial 25
Remote access 33
Reset to default settings 13
Review redial 25
Review the directory 17
Ring melody 8
Ring volume 9
V
Volume 9, 29
S
Search the directory 17
Set telephone base date and time 28
Set number of rings 28
Set telephone base melody 29
Set telephone base ringer volume 29
Speakerphone 14
Store an entry in the directory 19
Store a number from redial to the directory 25
Store a number from the call log 23
W
Warranty 51
T
Technical specifications 55
Telephone base 3, 7
Telephone settings 6
Temporary tone dialing 13
The RBRC ® Seal 54
Transfer an external call 16
Troubleshooting 40
www.vtechphones.com
57
VTECH TELECOMMUNICATIONS LTD.
A member of THE VTECH GROUP OF COMPANIES.
Distributed in the U.S.A. by VTech Communications, Inc. Beaverton, Oregon
Distributed in Canada by VTech Telecommunications Canada, Ltd., Richmond, B.C.
Copyright ©2006 for VTECH TELECOMMUNICATIONS LTD.
Printed in China.
91-001125-090-100
User’s manual
www.vtechphones.com
Models:
6042/6043/
6052/6053
Download PDF