Weslo | Cadence 1050 | User`s manual | Weslo Cadence 1050 User`s manual

ORDERING REPLACEMENT PARTS
To order replacement parts, contact the ICON Health & Fitness Ltd. office, or write:
ICON Health & Fitness, Ltd.
Customer Service Department
Unit 4, Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
Model No. WETL35020
Serial No.
Tel:
USER'S MANUAL
Write the serial number in the
space above for future reference.
08457 089 009
Serial
Number
Decal
Outside the UK: 0 (044) 113 387 7133
Fax: 0 (044) 113 387 7125
• the MODEL NUMBER of the product (WETL35020)
• the NAME of the product (WESLO CADENCE® 1050 treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING in the centre of this manual).
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you have
questions, or if there are missing
or damaged parts, please call:
08457 089 009
Or write:
ICON Health & Fitness, Ltd.
Customer Service Department
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
email: csuk@iconeurope.com
CAUTION
WESLO is a registered trademark of ICON Health & Fitness, Inc.
Part No. 182168 R0802A
Printed in USA © 2002 ICON Health & Fitness, Inc.
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.iconeurope.com
SUGGESTED STRETCHES
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING and a PART LIST are attached in the centre of this manual.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back and
groin.
IMPORTANT PRECAUTIONS
1
The correct form for several basic stretches is described below.
Move slowly as you stretch—never bounce.
3
3. Calf/Achilles Stretch
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least 2.5 m (8 ft.) of clearance behind it and
0.5 m (2 ft.) on each side. Do not place the
treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
10. When connecting the power cord (see page 7),
plug the power cord into an earthed circuit. No
other appliance should be on the same circuit.
When replacing the fuse, an ASTA approved
BS1362 type should be fitted to the fuse carrier. A 13 amp fuse should be used.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio or near water.
11. If you need an extension cord, use only a
1 mm2 (14-gauge) cord of 1.5 m (5 ft.) or less
in length.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
12. Keep the power cord away from heated surfaces.
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles tendons, bend your back leg as well. Stretches: Calves, achilles tendons and ankles.
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your buttocks as possible. Hold for 15 counts, then relax. Repeat 3 times
for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
13. Never move the walking belt whilst the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See BEFORE YOU BEGIN on page 4 if the treadmill is
not working properly.)
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should be used only by persons
weighing 115 kg (250 lbs.) or less.
14. Never start the treadmill whilst you are standing on the walking belt. Always hold the
handrails whilst using the treadmill.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
2
4
15
5
CONDITIONING GUIDELINES
WARNING: Before beginning
this or any exercise program, consult your
physician. This is especially important for individuals over the age of 35 or individuals
with pre-existing health problems.
The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
the first few minutes of exercise, your body uses easily
accessible carbohydrate calories for energy. Only after
the first few minutes does your body begin to use
stored fat calories for energy. If your goal is to burn fat,
adjust the speed and incline of the treadmill until your
heart rate is near one of the lower two numbers in your
training zone.
Aerobic Exercise
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the higher number in your training
zone.
EXERCISE INTENSITY
WORKOUT GUIDELINES
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the desired
results is to exercise with the proper intensity. The
proper intensity level can be found by using your heart
rate as a guide. The chart below shows recommended
heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate, and circulation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your heart rate is in
your training zone for 20 to 60 minutes. (During the
first few weeks of your exercise program, do not keep
your heart rate in your training zone for longer than 20
minutes.)
To find the proper heart rate for you, first find your age
near the top of the chart (ages are rounded off to the
nearest ten years). Next, find the three numbers below
your age. The three numbers are your “training zone.”
The lower two numbers are recommended heart rates
for fat burning; the highest number is the recommended heart rate for aerobic exercise.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time. During
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help to prevent postexercise problems.
EXERCISE FREQUENCY
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
16. Never leave the treadmill unattended whilst it
is running. Always remove the key and unplug the power cord when the treadmill is not
in use.
17. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on pages 5 and 6, and HOW TO
FOLD AND MOVE THE TREADMILL on page
10.) You must be able to safely lift 20 kg (45
lbs.) to raise, lower, or move the treadmill.
19. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
20. Inspect and properly tighten all parts of the
treadmill every three months.
21. Never drop or insert any object into any
opening.
22.
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures described in this manual. Never remove the
motor hood unless instructed to do so by an
authorised service representative. Servicing
other than the procedures in this manual
should be performed by an authorised service representative only.
23. This treadmill is intended for in-home use
only. Do not use this treadmill in any commercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decal shown below has been placed on your treadmill. If the decal
is missing or illegible, please call our Customer Service Department
to order a free replacement decal (see ORDERING REPLACEMENT
PARTS on the back cover of this manual). Apply the decal in the location shown.
Note: The decal is shown at 38% of actual size.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months of regular exercise, you may complete up to five workouts each week
if desired. The key to success is to make exercise a
regular and enjoyable part of your everyday life.
14
DANGER: Always unplug the power
3
PROBLEM: The walking belt slows when walked on
BEFORE YOU BEGIN
Thank you for selecting the WESLO CADENCE 1050
treadmill. The CADENCE 1050 combines advanced
technology with innovative design to let you enjoy an
excellent form of cardiovascular exercise in the convenience and privacy of your home. And when you’re not
exercising, the CADENCE 1050 can be folded up, requiring less than half the floor space of other treadmills.
please call our Customer Service Department at
08457 089 009. To help us assist you, please note the
product model number and serial number before calling. The model number of the treadmill is WETL35020.
The serial number can be found on a decal attached to
the treadmill (see the front cover of this manual for the
location).
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
Before reading further, please familiarise yourself with
the parts that are labelled in the drawing below.
®
Console
Water Bottle Holder
(Bottle not included)
SOLUTION: a. If an extension cord is needed, use only a 3-conductor, 1mm2 (14-gauge) cord that is no longer
than 1.5 m (5 ft.).
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt
5–7 cm (2–3 in.) off the walking platform. Be careful to
keep the walking belt centred. Plug in the power cord,
insert the key and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
b
5–7 cm
Rear Roller Adjustment Bolts
c. If the walking belt still slows when walked on, please call our Customer Service Department.
PROBLEM: The walking belt is off-centre or slips when walked on
Key/Clip
Storage Latch
Upright
Handrail
RIGHT SIDE
Walking Belt
Foot Grip
Circuit
Breaker
SOLUTION: a. If the walking belt is off-centre, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the allen wrench to
turn the left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right, turn the
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug in the power cord,
insert the key and run the treadmill for a few minutes.
Repeat until the walking belt is centred.
b. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller bolts clockwise,
1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each side of the walking belt 5–7 cm (2–3 in.) off the walking platform. Be
careful to keep the walking belt centred. Plug in the
power cord, insert the key and carefully walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
Cushioned Walking Platform
for maximum exercise comfort
Rear Roller
Adjustment Bolts
Incline Leg
BACK
4
13
a
b
TROUBLESHOOTING
ASSEMBLY
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department.
Assembly requires two persons. Set the treadmill in a cleared area and remove the packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own phillips screwdriver
, adjustable spanner
, needlenose
pliers
, and wire cutters
.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet (see page 7). If an extension cord is needed, use only a 1 mm2 (14-gauge) cord of 1.5 m (5 ft.) or less in length.
Important: The treadmill is not compatible with GFCI-equipped outlets.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
frame near the power cord. If the switch protrudes
as shown, the circuit breaker has tripped. To reset
the circuit breaker, wait for five minutes and then
press the switch back in.
c
Handrail Bolt (91)–2
Reset
Tripped
Tripped
Reset
Washer (39)–2
Screw (80)–6
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
Handrail Nut (93)–2
Handrail Washer (92)–2
Extension Leg
Screw (53)–2
Short Handrail Bolt (89)–2
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
1
WARNING: Do not plug in the power
cord until the treadmill is completely assembled.
d. If the treadmill still will not run, please call our Customer Service Department.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. UNPLUG THE POWER CORD. Check the batteries in the console. If the batteries need to be replaced, see BATTERY INSTALLATION on page 8. Most problems are the result of drained batteries.
11
1. With the help of a second person, carefully raise the
Uprights (11) until the treadmill is in the position shown.
b. Remove the key from the console and UNPLUG THE POWER CORD. Remove the screws from
the hood, and carefully remove the hood.
Locate the Reed Switch (44) and the Magnet (45) on
the left side of the Pulley (50). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that there is a gap of about 3 mm (1/8 in.) between
the Magnet and the Reed Switch. If necessary,
loosen the Screw (33), move the Reed Switch slightly,
and then retighten the Screw. Re-attach the hood, and
run the treadmill for a few minutes to check for a correct speed reading.
3 mm
50
44
45
33
Top
View
2. Insert one of the Extension Legs (34) into the treadmill
as shown. (Note: It may be helpful to tip the Uprights
[11] in the direction shown by the arrow as you insert
the Extension Leg.) Make sure that the Base Pad (40) is
on the indicated side of the Extension Leg. Attach the
Extension Leg with the Extension Leg Screw (53). Be
sure to push on the head of the Extension Leg
Screw whilst tightening it.
2
11
Attach the other Extension Leg (34) in the same way.
53
34
40
12
5
3. Refer to the inset drawing. If there is a plastic tie holding
the Cage Nut (70) in the Right Handrail (88), remove the
plastic tie. Feed the two Wires (21) in the right Upright (11)
up into the Right Handrail as shown. Using needlenose pliers, pull the two Wires out of the indicated hole in the
Right Handrail.
HOW TO LOWER THE TREADMILL FOR USE
3
89
89
39
39
11
1. Hold the upper end of the treadmill with your right hand
as shown. Using your left thumb, press the storage latch
and hold it. Pivot the treadmill down until the frame and
the foot rail are past the storage latch.
11
Unlatched
88
Insert the bracket on the Right Handrail (88) into the
upper end of the right Upright (11), with the lower end of
the Right Handrail touching the side of the Extension Leg
(34) as shown. Hand tighten a Short Handrail Bolt (89)
with a Washer (39) into the upper end of the right Upright.
Storage
Latch
21
88
70
Tie
34
11
4. Attach the lower end of the Right Handrail (88) to the
Extension Leg (34) with a Handrail Bolt (91), a Handrail
Washer (92), and a Handrail Nut (93) as shown. Do not
tighten the Handrail Bolt yet. Note: If necessary, push
on the lower end of the Handrail to align the hole in the
Handrail with the hole in the Extension Leg.
4
88
Attach the Left Handrail to the left Extension Leg (not
shown) as described in steps 3 and 4.
34
93
92
5. Place the Console Base (46) on the Uprights (11) (the
left Upright is not shown). Pull out just enough of the two
Wires (21) to connect them to the receptacles in the
Console Base. Make a loop with the indicated plastic tie
and insert the end through the tie holder on the bottom of
the Console Base. Locate the Wire that has a two-pin
connector and a three-pin connector. Plug the connectors
into the matching receptacles in the Console Base. If the
connectors do not fit easily, rotate them and then
plug them in. Slide the Wire Cover (107) onto the connectors so that they are completely covered. Next, plug
the other Wire into the other receptacle on the Console
Base. Tighten the plastic tie and cut off the end. WARNING: Do not connect or disconnect the Wires whilst
the treadmill power cord is plugged in.
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. Do not drop the treadmill frame to
the floor. To decrease the possibility of injury, bend
your legs and keep your back straight.
5
91
11
21
Tie
46
107
107
Tie
6
11
See the inset drawing. Loop the included plastic tie around
the Wire Cover (107) so that the plastic tie is in the two
notches in the Wire Cover. Tighten the plastic tie and cut
off the end.
6. Thread four Screws (80) into the Uprights (11) and the
Console Base (46). After all four Screws have been
started, tighten the Screws until they are snug. Do
not overtighten the Screws.
46
80
6
11
7. Attach the Storage Latch (14) to the left Upright (11) with
two Screws (80). Do not overtighten the Screws.
HOW TO FOLD AND MOVE THE TREADMILL
7
Tighten all of the bolts used in steps 3 and 4.
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, UNPLUG THE POWER CORD.
CAUTION: You must be able to safely lift 20 kg (45 lbs.)
in order to raise, lower, or move the treadmill.
80
11
14
1. Hold the treadmill with your hands in the locations shown
at the right. To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the
vertical position.
8. Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen
wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 13). To protect the
floor or carpet from damage, place a mat under the treadmill.
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
2. Move your right hand to the position shown and hold the
treadmill firmly. Raise the treadmill until the storage latch
closes over the catch. Make sure that the storage latch
is fully engaged over the catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage position in temperatures above 30°C (85°F).
Your treadmill features a walking belt coated with PERFORMANT LUBETM, a high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such
substances will deteriorate the walking belt and cause excessive wear.
HOW TO PLUG IN THE POWER CORD
Engaged
Storage
Latch
Catch
Two power cords are included. Select the one that will fit your
outlet. Refer to drawing 1, and plug the indicated end of the
power cord into the socket on the treadmill. Next, lift the indicated tab on the ferrite box and clamp the ferrite box around
the power cord. The ferrite box should not be allowed to slide
along the power cord. Fasten the included plastic tie just behind the ferrite box and cut off the excess plastic tie. Refer to
drawing 2. Plug the power cord into an appropriate outlet that is
properly installed and earthed in accordance with all local
codes and ordinances. Note: In Italy, an adaptor (not included)
must be used between the power cord and the outlet. Important:
The treadmill is not compatible with GFCI-equipped outlets.
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the storage latch is closed fully over the catch.
1. Hold the upper ends of the handrails. Place one foot on
the base as shown.
2. Tilt the treadmill back until it rolls freely on the front
wheels. Carefully move the treadmill to the desired location. To reduce the risk of injury, use extreme caution
whilst moving the treadmill. Do not move the treadmill over an uneven surface.
3. Place one foot on the base, and carefully lower the treadmill until it is resting in the storage position.
10
This product must be earthed. If it should malfunction or break
down, earthing provides a path of least resistance for electric
current to reduce the risk of electric shock. This product is equipped
with a cord having an equipment-earthing conductor and an earthing plug.
If the power cord is damaged, it must be replaced with a manufacturer-recommended power cord.
Base
Front Wheels
DANGER:
Improper connection of the
equipment-earthing conductor can result in an increased risk of electric shock. Check with a qualified
electrician or serviceman if you are in doubt as to
whether the product is properly earthed. Do not modify the plug provided with the product—if it will not fit
the outlet, have a proper outlet installed by a qualified
electrician.
7
1
Socket on treadmill
Ferrite Box
Plastic
Tie
Tab
2
Outlet
DIAGRAM OF THE CONSOLE
Displays
Incline Control
1
Calories/Fat Calories/
Arrow
Pulse display—This
display shows the approximate numbers of
calories and fat calories
you have burned. (See
FAT BURNING on page
14.) Every few seconds, the display will change from
one number to the other, as indicated by the arrows.
This display will also show your heart rate when you
use the pulse sensor (see step 5).
Insert the key fully into the console.
Inserting the key will not
turn on the displays.
The displays will turn on
when the ON/RESET
button is pressed or
when the walking belt is
started. Note: If you just
installed batteries, the displays will already be on.
2
Reset the console and start the walking belt.
To reset the displays at any time, press the
ON/RESET button.
Slide the speed control to the
RESET position. Note: Each
time the walking belt is
stopped, the speed control
must be moved to the RESET
position before the walking
belt can be restarted.
Speed Control
Decal
Key
Clip
Pulse Sensor
console, read the following precautions.
To stop the walking belt, step onto the foot grips
and slide the speed control to the RESET position.
• Adjust the speed in small increments.
• Do not stand on the walking belt when turning
on the power.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids on
the console. Use only a sealable water bottle.
• Always wear the clip (see the drawing above)
whilst using the treadmill. When the key is re-
BATTERY INSTALLATION
3
The console requires three “AA” 1.5 V batteries (included). Alkaline batteries are recommended. To install
the batteries, open the battery cover as shown below.
Press the batteries into the battery compartment, with
the negative (–) ends of the batteries touching the
STEP-BY-STEP CONSOLE OPERATION
If there is a thin sheet of plastic on the console, remove it.
Battery Cover
Next, step onto the foot grips of the treadmill. Find the
clip attached to the key (see the drawing above), and
slide the clip onto the waistband of your clothes. Test
the clip by carefully taking a few steps backward
until the key is pulled from the console. If the key
is not pulled from the console, adjust the position
of the clip as needed.
Tab
Batteries
Follow the steps on page 9 to operate the console.
8
Adjust the incline of the treadmill as desired.
To change the incline of the
treadmill, press the top or bottom of the incline control until
the desired incline level is
reached.
springs. Close the battery cover, push up on the tab,
and then push the tab forward as shown. Be sure that
the tab locks into place.
4
Measure your heart rate, if desired.
To measure your heart
Pulse Sensor
rate, stand on the foot
grips and place your
thumb on the pulse
sensor as shown. The
pulse sensor is pressure activated—fully
press it down. Do not
press too hard, or the circulation in your thumb
will be restricted and your pulse will not be detected. Next, raise your thumb slightly until the
heart shaped indicator in the Calories/Fat Calories/
Pulse display flashes steadily. Hold your thumb at
this level. After a few seconds, three dashes will
appear and then your heart rate will be shown.
Hold your thumb on the sensor for 15 seconds for
the most accurate reading.
Next, slowly slide the speed control up until the
walking belt begins to move at slow speed.
Carefully step onto the walking belt and begin
walking. Change the speed of the walking belt as
desired by sliding the speed control.
moved from the console, the walking belt will
stop.
CAUTION: Before operating the
5
If the displayed heart rate appears to be too high
or too low, or if your heart rate is not displayed, lift
your thumb and allow the display to reset. Then,
press down again on the sensor as described
above. Try the sensor several times until you are
familiar with it. Remember to stand still whilst measuring your pulse.
Follow your progress with the three displays.
Time/Distance
Arrow
display—This display
shows the elapsed time
and the distance that
you have walked or run.
Every few seconds, the
display will change from
one number to the other, as indicated by the arrows.
6
Remove the key from the console.
When you are finished exercising, step onto the
foot grips, slide the speed control to the RESET
position, and remove the key. The displays will
turn off a few minutes after the key is removed.
Note: Any time that the walking belt is stationary and the console is not used for a few minutes, the displays will turn off automatically.
Speed display—This
display shows the speed
of the walking belt.
9
PART LIST—Model No. WETL35020
R0802A
Description
No. Qty.
Description
No. Qty.
Description
1
2
3
4
5
6
7
8
9
10*
11
12
13
14
15
16
17
1
1
2
2
1
1
1
1
1
1
1
1
7
1
6
7
4
86
87
88
89
90
91
92
93
94
95
96
97
1
2
1
2
1
2
2
2
1
2
1
12
21
22
23
24
25
26
27
28
29
1
3
1
1
11
1
1
1
1
30
31
32
33
1
2
1
10
98
99
100
101
102
103
104
105
106
107
108
109
#
#
#
4
2
1
1
3
1
1
1
1
1
1
1
1
1
2
34
35
36
37
2
1
2
2
Wheel Nut/Lift Nut
Washer
Base Pad
Belt Bracket
Latch Catch
Reed Switch Clip
Reed Switch
Magnet
Console Base
Frame Spacer
Platform Screw
Centre Isolator
Front Roller/Pulley
Front Roller Adj. Bolt
Incline Wheel
Extension Leg Screw
Euro Power Cord Set
Receptacle
Circuit Breaker
Frame Pivot Washer
Frame Pivot Bolt
Latch Decal
Motor Belly Pan
Cable Tie Clamp
Rear Platform Screw
Releasable Tie
Filter
Belt Guide
Belly Pan Fastener
Walking Belt
Walking Platform
Belly Pan
Cage Nut
Incline Wire Harness
Upright Grommet
Isolator Screw
Allen Wrench
Frame
Front Endcap (Left)
Incline Wheel Bolt
Rear Pad (Left)
1
12
1
1
2
1
2
1
1
1
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85*
18
19
20*
Left Handrail
Key/Clip
Incline Leg Pivot Bolt
Battery Cover
Foot Grip (Left)
Lift Motor
Rear Roller
Speed Potentiometer
Speed Control Knob
Console Assembly
Upright
Motor Belt
Small Screw
Storage Latch
Controller Screw
8” Cable Tie
Incline Leg Nut/Base
Nut
Pulley/Flywheel/Fan
Motor
Motor/Pulley/Flywheel/
Fan
Wire Harness/Wires
Motor Pivot Nut
Motor Hood
Hood Shield
Utility Screw
Controller
Motor Swivel Bolt
Motor Tension Nut
Motor Tension Star
Washer
Motor Tension Washer
Motor Tension Bolt
Incline Stop Bracket
Belly Pan Screw/
Guide Screw
Extension Leg
Hood Shield Plug
Wheel Bolt
Wheel
#
#
#
#
1
1
1
1
Rear Pad (Right)
Screw
Ground Wire
Incline Leg
Rear Roller Adj. Bolt
Rear Endcap
Extension Leg
Assembly
Foot Grip (Right)
Belly Pan Screw
Right Handrail
Short Handrail Bolt
Front Endcap (Right)
Handrail Bolt
Handrail Washer
Handrail Nut
Incline Motor Bolt
Front Isolator
Power Filter Wire
Endcap Screw/
Console Screw
Belt Guide Screw
Motor Pivot Bushing
Electronic Bracket
Motor Pivot Sleeve
Nylon Washer
Ground Screw
Ground Star Washer
Ground Nut
Incline Filter Wire
Wire Cover
Choke
Ferrite Clamp
4” White Wire, 2F
4” Black Wire, M/F
4” Green/Yellow,
F/Ring
4” Black Wire, 2F
14” Wire Harness
6” Black Wire, 2 Ring
User’s Manual
* Includes all parts shown in the box
# These parts are not illustrated
4
5
6
1
1
1
1
1
1
2
4
2
1
1
2
2
1
1
1
2
2
1
1
2
4
3
1
2
4
1
1
1
2
1
1
4
1
1
1
2
1
REMOVE THIS EXPLODED DRAWING AND PART LIST
FROM THE MANUAL
Save this EXPLODED DRAWING and PART LIST for future reference.
34
No. Qty.
Note: Specifications are subject to change without notice. For information about
ordering replacement parts, see the back cover of the User’s Manual.
EXPLODED DRAWING—Model No. WETL35020
R0802A
25
2
89
39
9
8
80
10*
80
12
11
46
21
27
70
80
97
23
99
89
20*
39
14
97
24
18
85*
19
34
25
97
1
25
107
4
93
36
97
97
37
76
61
48
47 17
17
45 44
71
91
43
49
57
95
5
86
25
70
100
17 47
72
57
93
48
58
95
75
62
53
65
98
98
37
22
7
73
49
40
98
69
88
85*
40
36
106
13
40
34
17
6
64
104
25
25
80
103
53
98
105
79
56 35
108
13
40
68
32
55
26
51
39
67
98
42
62
41
13
48
78
31
80
102 28
90
92
94
25
50
48
73
97
33
25
22
99
29
31
30 101
58
97
65
102
40
25
13
96
25
84
74
77
25
66
3
87
22
52
63
33
59
82
3
61
66
16
38
39
33
83
39
33
33
60
38
83
54
33
81
38
38
33
52
92
40
77
33
25
98
91
109
Download PDF