Magnum | 246186 | Technical data | Magnum 246186 Technical data

Repair
Interior Texture Sprayers
TexFinish™
309797P
U.S. patent D526,045
For Water-Based Materials Only
Models: 246185, 246186, 249175, 249176
55 psi (3.79 bar) Maximum Fluid Working Pressure
Read warnings and instructions.
Related Manuals
309584
309796
ti3157b
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
www.graco.com
Copyright 2003
Graco Inc. is registered to I.S. EN ISO 9001
US
C
Conforms to ANSI/UL
standard 1450
WARNINGS
Fire and Explosion Hazard
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result
in fire or explosion and serious injury.
•
The system is for use with water-based materials only. Only use fluids compatible with the
equipment. Refer to Technical Data of all equipment manuals. Read fluid and solvent manufacturers
warnings.
•
Ground the equipment. See Grounding and Electrical Requirements, page 5.
•
If there is any static sparking or you feel an electric shock while using this equipment, stop spraying
immediately. Do not use the equipment until you identify and correct the equipment until you identify
and correct the problem.
•
Keep work area free of debris, including solvent, rags and gasoline.
•
Comply with all applicable state and national fire, electrical and safety regulations.
Equipment Misuse Hazard
Equipment misuse can cause equipment to rupture, malfunction, or start unexpectedly and cause
serious injury.
2
•
Before operating this equipment, read all manuals, tags, and labels, including material labels and
instructions.
•
Do not expose system to rain. Always store system indoors.
•
Do not alter or modify equipment.
•
Do not spray cementcious materials.
•
Do not exceed maximum working pressure of lowest rated component in your system.
•
Check equipment daily. Repair or replace worn or damaged parts immediately.
•
To reduce risk of serious injury, including electric shock and splashing fluid in eyes, follow Pressure
Relief Procedure on page 5 before servicing the unit.
•
Do not use hoses to pull equipment.
•
Route hoses away from traffic areas, sharp edges, moving parts and hot surfaces. Do not expose
Graco hoses to temperatures above 130 F (55 C) or below -35 F (-37 C).
•
Air hoses at the compressor end, can get very hot! Allow sprayer to cool down 15 minutes before
removing air hose.
•
Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
•
Never directly inhale compressed air. Compressed air may contain toxic vapors.
309797P
WARNINGS
Electric Shock Hazard
To reduce the risk of electric shock:
•
Be sure sprayer is adequately grounded through electrical outlet, page 5.
•
Use only 3-wire, extension cords.
•
Make sure ground prongs are intact on sprayer and extension cords.
•
Do not operate with cover removed.
•
Turn off sprayer. Follow Pressure Relief procedure, page 5, and unplug unit, before removing any
parts.
Pressurized Equipment Hazard
Fluid from gun, leaks or ruptured components can splash in the eyes or on skin and cause serious injury.
•
Follow Pressure Relief Procedure, page 5 when you stop spraying and before cleaning, checking
or servicing.
•
Do not point spray gun at anyone; put hand, fingers or rag over nozzle, or stop or deflect leaks with
your hand, body, glove, or rag.
•
Wear protective clothing, gloves, and eyewear.
•
Before adding material to hopper, install burp guard. When only a small
amount of material remains in the hopper, the burp guard prevents material
from shooting out when the unit is turned off. This material could splash in
the operator’s eyes or on skin, or into the air.
ti2894a
Cleaning Solvent Hazard with Plastic Parts
Use only compatible water-based solvents to clean plastic structural or pressure-containing parts. Many
solvents can degrade plastic parts to the point where they could fail. Such failure could cause serious
injury or property damage. See Technical Data on page 25 of this instruction manual and in all other
equipment manuals. Read fluid and solvent manufacturer’s warnings.
CAUTION
Water or material remaining in unit when temperatures are below freezing can damage
motor and/or delay pump startup.
To insure water and material are completely drained out of unit:
1. Remove material line from sprayer.
ti3159a
2. Tip sprayer up as shown.
Before adding material or starting unit in cold weather, run warm water through pump.
309797P
3
Component Identification
Component Identification
H
P
K
N
M
Y
bb
dd
aa
B
S
D
U
E
A
WLF
R
W
J
F
L
T
G
cc
ti3157b
Item
4
Component
Item
Component
A
Air hose outlet
P
Nozzle storage
B
Material hose outlet
R
Hose plug
D
Hopper gun/spray gun selector switch
S
Gun plug
E
ON/OFF switch
T
Material thickness gauge
F
Air Compressor (inside)
U
Nozzle
G
Material/air hose
W
Gun air valve
H
Mesh nozzle holding bag
Y
Burp guard
J
Texture spray gun (manual 309584)
aa
Hopper fitting (fluid inlet)
K
Material Hopper
bb
Hopper clamp
L
Graco RotoFlex™ pump (inside)
cc
Hose clip
M
Hose rack/cord wrap
dd
Gun plug clip
N
Touch-up hopper (3/4 gallon)
309797P
Preparation
Preparation
Pressure Relief
WARNING
To reduce risk of injury, follow this procedure
whenever you see this symbol throughout this
manual, Also, perform this procedure whenever
you:
page 2
120V AC Systems
•
stop spraying.
•
check or repair any part of this system.
•
install or clean spray nozzle.
•
WARNING
page 2
This equipment
requires a 120V
AC, 60 Hz, 15A
circuit with a
grounding
receptacle. Do not
use an adapter
with this product.
grounded
outlets
grounding prong
Extension Cords
1. Turn Power Switch OFF.
•
Use only an extension cord with an undamaged,
3-prong plug.
•
For 25 to 50 ft (7.6 to 15.2 m) cords, use 3-wire, 14
AWG (1.5 mm2) minimum.
•
For up to 100 ft. (30.48 m) cord, use 3-wire, 12 AWG
(2.5 mm2) minimum.
TI2458a
2. Trigger gun into material
hopper.
Auxiliary Air Compressor
Do not use an auxiliary air compressor with this spray
system.
ti3160a
Generator Requirements
3. Open gun air valve.
3500 W (3.5 KW) minimum.
Hose Size and Length
ti2448a
Grounding and Electrical Requirements
This sprayer must be grounded. Grounding reduces the
risk of electrical shock by providing an escape wire for
the electrical current. The sprayer cord includes a
grounding wire with an appropriate grounding plug. The
plug must be plugged into an outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
The system comes with a hose set consisting of a 3/4 in.
ID x 25 ft (25 mm x 7.6 m) material hose and a 3/8 in-ID
air hose.
Do not use more than 25 ft. (7.6 m) of material hose.
WARNING
page 2
Check with a qualified electrician or serviceman if
grounding instructions are not completely understood,
or if in doubt as to whether the product is properly
grounded. Do not modify plug provided; if it will not fit
the outlet, have proper outlet installed by a qualified
electrician.
309797P
5
RotoFlex™ Pump
RotoFlex™ Pump
6. Loosen bolt (A)
located between air
and material hose
outlets. Unscrew
bolt to lower plate,
leaving about 4-5
A
threads on bolt.
Use RotoFlex Pump Kit 234156.
Disassembly
1. Relieve Pressure, page 5.
2. Unplug sprayer from outlet.
ti3083a
3. Remove shroud
(6 bolts).
DO NOT REMOVE
BOLT COMPLETELY.
6
5
1
4
2
ti3162a
7. Slide a 2 x 4
under motor for
support.
3
4. Remove hopper by
loosening bottom
fitting and then lifting hopper straight
up, off unit.
ti3124a
ti3118a
8. Rotate plate.
Slide hose off by
pushing outward on
hose fitting.
ti3119a
5. Remove material
hose.
ti3132a
6
309797P
RotoFlex™ Pump
Reassembly
3. Align dots located on hose fitting, making sure they
are facing each other at all times to ensure the hose
does not twist during reinstallation.
Reinstall RotoFlex Pump hose on plate.
1. Kink hose as shown,
making sure dots
located on hose fitting
face each other.
DOTS
ti3084a
4. Reposition plate, aligning hex fittings with enclosure
openings.
5. Remove 2 x 4 support under motor.
ti3127a
6. Tighten bolt. As bolt is tightened the plate will snug
back into place.
2. Slide hose onto plate
as shown below, making sure plate slides
into slot between hex
fitting on end of hose.
7. Replace shroud (6 bolts).
8. Replace hopper.
9. Break in new pump by running dry or with warm
water for 3-5 minutes.
ti3125a
309797P
7
Compressor Repair
Compressor Repair
7. Tilt compressor forward
and remove from housing.
Use Compressor Repair Kit, 234211.
Disassembly
1. Relieve Pressure, page 5.
2. Unplug sprayer.
TI3011a
3. Remove shroud (6 bolts).
6
5
1
4
2
CAUTION
Fan blades are very delicate and can be damaged very
easily. When removing or replacing compressor, do not
bump or jar shroud or fan blades.
ti3162a
8. Thoroughly clean inside housing, removing dust and
debris.
3
4. Remove green
ground wire and
black, and white
wires to compressor.
Reassembly
1. Carefully position compressor in housing.
2. Replace bolts using socket wrench to tighten.
Torque to 85 in. lbs.
ti3022a
3. Reattach air lines to
compressor. Finger
tighten plus one full
turn, fittings (A and
B).
5. Loosen fittings (A and B) and remove air line.
ti2748a
A
6. Using a socket wrench
with extension, loosen
bolts (3).
B
ti2749a
bolt
4. Reattach 3 wires to
compressor matching
green to green, black to
black and white to white.
bolt
5. Replace shroud. Tighten bolts (6).
ti3032a
bolt
8
309797P
Roller Replacement
Roller Replacement
Reassembly
Use Roller Repair Kit 234214.
Disassembly
CAUTION
When installing bolt through roller, keep nylon washer
on shoulder of bolt.
1. Relieve Pressure, page 5.
2. Unplug sprayer from outlet
1. Replace rollers.
3. Remove shroud (6 bolts).
6
5
ti3030a
1
2
ti3162a
3
2. Using a crow bar as a wedge to keep rollers from
moving, torque bolts to 40 ft. lbs.
4. Remove RotoFlex Pump, page 6.
5. Using a crow bar
as a wedge to
keep rollers from
moving, loosen
shoulder bolt.
ti3029a
ti3026a
6. Remove rollers.
3. Reinstall RotoFlex Pump hose on plate, page 6.
ti3031a
309797P
4. Replace shroud. Tighten bolts (6).
9
Cylinder
Cylinder
Use Cylinder Repair Kit 246574.
Reassembly
Disassembly
1. Insert swing arm through
hole.
ti3086a
1. Relieve Pressure, page 5.
2. Unplug sprayer from outlet.
3. Remove shroud (6 bolts).
6
5
2. Align hole in bottom of cylinder with holes in bottom
bracket.
1
4
2
3. Feed pin through.
ti3162a
4. Replace clip.
3
4. Disconnect air hose at quick
disconnect fitting.
ti3087a
TI2851A
5. Reattach air hose to quick
disconnect fitting.
5. Remove
clip.
TI2852A
6. Replace shroud. Tighten bolts (6).
6. Remove
pin.
ti3085a
7. Pull swing arm out of opening.
10
309797P
Capacitor Replacement
Capacitor Replacement
5. Cut strap.
Use Capacitor Replacement Kit 246683.
6. Unplug capacitor and
remove.
WARNING
page 2
ti3167a
Disassembly
7. Clean surface to remove dirt and any remaining
adhesive.
1. Relieve Pressure, page 5.
2. Unplug sprayer.
3. Remove shroud,
(6 bolts).
Reassembly
6
5
1. Remove backing from one side of two-sided tape
provided in kit and apply to bottom of capacitor.
1
4
2
2. Plug in new capacitor.
ti3162a
4. Capacitors can
hold a charge. To prevent electric shock,
use a flat bladed
screw driver as a conductive device to short
out the terminals. To
do this, touch the
blade of the flat screw
driver between two
terminal posts on the
capacitor.
3
ti3168a
ti3166a
CAUTION
Do not touch metal part of screw driver when
shorting out capacitor.
309797P
Wires are not polarized. It does not matter which
wires are connected together between capacitor
and motor.
3. Remove backing from bottom of two sided tape.
Attach capacitor to plate,
pressing taped side firmly
into position. Secure using
a wire tie.
ti3090a
4. Replace shroud. Tighten
bolts (6).
11
Motor Repair
Motor Repair
10. Using a flat screw driver,
remove c-clip (E).
Use Motor Repair Kit 246572.
E
Disassembly
1. Relieve Pressure, page 5.
TI3099a
2. Unplug sprayer from outlet.
3. Remove shroud (6 bolts).
11. Using your hand to support the motor, carefully
pull rod (F) out through
back.
6
5
1
4
2
12. Bring motor to workbench.
F
TI2858A
ti3162a
13. Remove 4 bolts (G)
holding motor to
bracket.
3
4. Remove RotoFlex Pump hose; page 6.
5. Remove Air Cylinder; page 10.
6. Cut wire tie (A).
TI2859A
G
A
14. Cut wire tie. Remove
capacitor from plate,
page 11.
7. Remove yellow wire (B).
TI2860A
Reassembly
TI2854A
B
1. Reposition motor in housing, keeping motor square
and aligned to pulley.
8. Remove ground nut (C).
C
2. Keeping tension on belt, tighten 4 bolts (G). Torque
to 15 ft-lbs.
The motor will have a tendency to move when
bolts are being tightened. Hold it securely in
place, square and aligned to pulley.
TI2855A
9. Remove blue wire to
switch (D).
D
3. Secure new capacitor to plate,
page 11.
ti3090a
TI2856A
12
309797P
Motor Repair
8. Reattach yellow wire (B).
4. Using one hand to support
motor, slide rod (F) through
motor bracket.
9. Secure all wires together with wire tie (A), making
sure the wires to not touch air line (H) and the motor
can swing the full travel (I) without stressing wires.
F
TI2861A
5. Replace c-clip (E).
(C)
E
ti308
(A)
For steps 6-9 refer to illustration below Step 9.
6. Reattach blue wire to switch (D).
(B)
7. Replace ground nut (C).
(H)
(I)
ti3117a
(D)
10. Reconnect RotoFlex Pump hose, page 6.
11. Replace shroud. Tighten bolts (6).
309797P
13
Cooler Repair
Cooler Repair
6. Carefully drill out rivets.
Use Cooler Repair Kit 246578.
Disassembly
1. Relieve Pressure, page 5.
2. Unplug sprayer.
ti3096a
3. Remove shroud (6 bolts).
6
5
7. Pull cooler out of housing.
1
4
2
ti3162a
Reassembly
1. Install cooler in housing.
3
4. Loosen nuts (A and B).
2. Rivet (or use fasteners) in place.
A
B
ti3097a
5. Disconnect air hose at
fitting.
ti3128
3. Reconnect tubing.
Torque nuts (A and B) one full turn beyond hand
tight.
4. Replace shroud. Tighten bolts (6).
14
309797P
Relief Valve Replacement
Relief Valve Replacement
Reassembly
Use Air Relief Valve Kit 246580.
1. Reattach air hoses at quick disconnect fitting.
Disassembly
1. Relieve Pressure, page 5.
2. Unplug sprayer.
3. Remove shroud (6 bolts).
6
5
TI3098a
1
4
2. Slide air manifold back into position inside housing.
2
ti3162a
3
4. Remove screw on
top of unit.
ti3094a
5. Remove air lines.
ti2736a
3. Replace screw on top of unit - torque to 30 in. lbs.
6. Pull air manifold down through inside of housing.
4. Replace shroud. Tighten bolts (6).
7. Disconnect air hose at quick disconnect fitting.
TI3093a
309797P
15
Rotor Replacement
Rotor Replacement
7. Remove rotor.
Use Rotor Kit 246585 (includes Roller Kit 234214)
Disassembly
1. Relieve Pressure, page 5.
2. Unplug sprayer.
TI2868A
3. Remove shroud (6 bolts).
4. Remove RotoFlex pump
hose, page 6, Disassembly, steps 4-8.
Reassembly
6
5
1. Install rotor with flange facing outward.
2. Replace c-clip (A).
1
4
2
3. Install rollers, page 9, Reassembly.
5. Remove rollers, page 9,
Disassembly.
ti3162a
4. Install RotoFlex Pump hose and shroud, page 7,
Reassembly.
3
6. Using a flat screwdriver,
remove c-clip (A).
A
TI3099a
16
309797P
Troubleshooting
Troubleshooting
Pressure Relief, page 5
Problem
Sprayer won’t run
Pump won’t pump material
Cause
Solution
Power switch not on
Turn switch on.
No power at wall outlet
Check outlet by plugging in another
appliance. If appliance does not
work, try another outlet.
Wrong size generator
Use a 3500 watt or larger generator.
Refer to Generator Requirements,
page 5
Too many items on same circuit
Unplug other items from circuit
Extension cord too long or wrong
gauge
Use a different extension cord. Refer
to Grounding and Electric Requirements, page 5
Breaker tripped
Reset breaker
Selector switch in wrong position
Move selector switch to correct position for application
Air lock
Open air valve on gun
Mix too thick
Add water to thin material. Use Material Thickness Gauge.
Loose fittings
Check and retighten all fittings
Plugged gun
Relieve Pressure, page 5. Remove
gun from hose. Clean gun.
RotoFlex pump worn out
Replace hose. Recommended hose
replacement - once a year or every
3000 gallons.
Pump cold or material frozen in pump Move pump to warm room and allow
it to warm up or run hot water through
sprayer.
Motor start capacitor failure
Material runs out of bottom of sprayer RotoFlex pump worn out
No air from compressor
309797P
Replace capacitor and restart
Replace hose
Loose fittings
Check and retighten all fittings
Gun air valve closed
Open gun air valve
Low voltage
Check extension cord length and
gauge. Replace if different than recommended. Refer to Grounding and
Electrical Requirements, page 5.
Gun needle plugged
Clean needle and retry.
Lines not connected
Check all quick disconnect connections to gun and hoses
Damaged hose
Replace hose
Worn compressor
Replace compressor. Contact a qualified Graco Service Center.
17
Troubleshooting
Problem
Speed of application too slow
Cause
Solution
Material too thick
Thin material.
Nozzle too small
Change nozzles to a larger size. See
Operation Manual, Recommended
Nozzle Selection Chart, page 10.
Too much air being used.
Partially close gun air valve to reduce
air flow.
Plugged or dirty gun
Relieve Pressure, page 5. Clean
gun.
Kinked hose
Unkink hose.
Gun fluid flow adjustment set too low Increase flow adjustment with flow
adjustment nut.
RotoFlex pump worn
Replace hose.
Hopper connection not tight
Check gasket. TIghten connection.
Debris in system
Clean
Quick disconnect does not stay connected.
Dirty or corroded fitting
Clean thoroughly. Soak in oil. Apply a
few drops of light oil.
Gun will not shut off
Worn nozzle or needle.
Relieve Pressure, page 5. Replace
worn parts.
Debris in needle passage
Relieve Pressure, page 5. Clean.
Intermittent flow/sputtering
Fluid leaking at Flow Adjustment Nut Damaged seal.
Relieve Pressure, page 5. Replace
seal.
Fluid leaking out of either plug
Missing or damaged o-rings
Relieve Pressure, page 5. Replace
o-rings.
Gun damaged
Replace gun
Dirty threads
Clean threads
Nozzle not on gun
Put nozzle on gun
Needle adjustment won’t adjust
18
309797P
Wiring Diagram
Wiring Diagram
ELECTROLYTIC CAPACITOR
BLACK
BLACK
MOTOR
BLUE
YELLOW
POWER
SWITCH
SELECTOR
SWITCH
GREEN
GROUND
GREEN
POWER
CORD
WHITE
GREEN
BLACK
WHITE
BLACK
BLACK
ti3120a
AIR COMPRESSOR
Air Diagram
AIR MANIFOLD
AIR COOLER
AIR CYLINDER
TI3179a
AIR COMPRESSOR
309797P
19
Parts
Parts
D
F
E
F
D
81
WLH
3DJH
20
309797P
Ref
No.
3
4
6
9
10
11
20
21
22
23
27
34
36
36a
38
39
Part No.
117563
117693
15A903
15C087
15B873
246580
117630
117633
117636
234157
113415
15B865
234148
248930
234217
246316
309797P
Description
SWITCH, selector
SWITCH, on/off
PLATE, hose
PLATE, frame, top
SUPPORT, front, frame
KIT, manifold, air, includes 19
SCREW, torx, tri-lob
SCREW, slot, hex wash hd
SCREW, hex hd, flanged
KIT, RotoFlex pump
SCREW, mach, torx pan hd
SHIELD
KIT, hose
KIT, quick disconnect
GUN, texture, manual 309584
HOPPER, 6-gallon
Qty
1
1
1
1
1
1
8
6
1
1
1
1
1
1
1
1
Ref
No.
39a
39b
39c
52
57
59
60
63
67
76
78
79
81
85
Part No.
15B676
15B990
115099
15B823
15B822
290228
15B889
234222
15B986
15C128
15C090
246683
15H240
287967
Description
STORAGE, nozzle
GUARD, burp
GASKET
TUBE, air
TUBE, air
LABEL, caution
LABEL
HOPPER, texture, .75 gal
CLIP, spring
LABEL, danger
GAUGE, material thickness
KIT, capacitor
BAG, mesh
CLIP, plug, gun
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Replacement Danger and Warning labels, tags and cards
are available at no cost.
21
22
WLF
3DJH
309797P
Ref
No.
1
5
8
12
13
14
15
16
Part No.
234214
15B858
246585
15B439
15B530
15B861
15B543
15B857
249204
17
18
246189
246574
19
117625
15F408
20
24
25
26
28
29
30
31
32
33
35
117630
15B529
246572
112612
115095
115480
116630
195367
15B585
117727
234211
309797P
Description
Qty
KIT, roller
1
LEG, frame
1
KIT, pulley, includes 1, 2, 41
1
SHAFT, pivot, motor tray
1
ROD, axle
1
HANDLE,
1
RACK, hose
1
FRAME, bottom, model 246185,
1
246186
FRAME, bottom model 249175,
1
249176
TRAY, motor
1
KIT, cylinder, air, includes 24, 46,
1
47
NUT, locking, model 246185,
1
246186
NUT, locking, model 249175,
1
249176
SCREW, torx, tri-lob
8
ARM, cylinder
1
KIT, motor, AC, includes 41, 66, 79
1
CAP, hub
2
WHEEL, 9”
2
KNOB, t-handle
2
SCREW, carriage
2
SPACER
2
HARNESS, wiring
1
CLIP, wire
3
KIT, compressor, air, includes 54
1
Ref
No.
37
41
44
45
46
47
48
49
50
51
54
55
56
57
58
62
63
66
74
75
77
79
80
82
Part No. Description
Qty
15B507 CORD set, power, model 246185,
1
246186
15F404 CORD set, power, model 249175,
249176
117672 BELT, GT2, 3mm
1
101134 RING, retaining, ext.
1
101242 RING, retaining, ext
2
117671 PIN, clevis
1
117668 PIN, cotter, bow tie
1
115498 SCREW, mch, hx wash hd
1
15B783 SHIELD, spray
1
246578 KIT, cooler, air, includes 51, 54, 56
1
113084 RIVET, blind
2
15B818 TUBE, air
1
115651 NUT, hex, acorn, 5/16-18
1
117728 FITTING, compression, union
2
15B822 TUBE, air
1
198492 LABEL, warning
1
103473 STRAP, tie, wire
2
234222 HOPPER, texture, .75 gal
1
117791 SCREW, cap, tri-lobe
4
186620 LABEL, symbol, ground
1
15C127 LABEL, instruction
1
291292 LABEL, identification
1
246683 KIT, capacitor
1
*113318 ELBOW
1
*104172 FITTING
1
117472 METER, hour
1
* When repairing elbow, order both part numbers for 80
23
24
309797P
Technical Data
Technical Data
Main unit power requirements. . . . . . . . . . . . . . . . . . . . . .
Maximum fluid working pressure . . . . . . . . . . . . . . . . . . .
Maximum air working pressure . . . . . . . . . . . . . . . . . . . . .
Compressor specifications . . . . . . . . . . . . . . . . . . . . . . . .
Compressor air displacement . . . . . . . . . . . . . . . . . . . . . .
Generator required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electric Motor
Material pump motor . . . . . . . . . . . . . . . . . . . . . .
Compressor motor . . . . . . . . . . . . . . . . . . . . . . . .
Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
120 Vac, 60 Hz, 15A, 1 phase
55 psi, (3.8 bar)
38 psi (2.6 bar)
Universal motor thermally protected, oil-less
4.5 displacement scfm at 30 psi
3500 W minimum
Capacitor start 1/3 hp AC, 2.8A open frame
Universal AC 10.5A
14 AWG, 3-wire, 25 ft (model 249175, 249176)
16 AWG, 3-wire, 25 ft (model 246185, 246186)
Material hopper capacity. . . . . . . . . . . . . . . . . . . . . . . . . . 6 gallons
Gun material hopper: 3/4 gallon
Maximum delivery with texture . . . . . . . . . . . . . . . . . . . . . 0.75 gpm (2.8 lpm)
Dimensions:
Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 in. (584 mm) with handle
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 in. (584 mm)
Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 in. (991 mm)
Weight
Without hoses or gun . . . . . . . . . . . . . . . . . . . . . . 75 lb (34 kg)
Wetted parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . brass, aluminum, plastic
Sound data
Sound pressure level* . . . . . . . . . . . . . . . . . . . . . 83.2 dB(A)
Sound power level**. . . . . . . . . . . . . . . . . . . . . . . 97.5 dB(A)
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . 35°F - 160°F (1.6°C - 71°C)
Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . 40°F - 115°F (4°C - 46°C)
Gun:
Maximum Working Pressure . . . . . . . . . . . . . . . . 60 psi (4.137 bar)
Air Maximum Working Pressure . . . . . . . . . . . . . 100 psi (6.895 bar)
CFM Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5 - 11 CFM
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 lb (500 g)
* Measured while spraying at 1 m.
** Measured per ISO-3744
309797P
25
Limited Warranty
Limited Warranty
Graco warrants to the original purchased (other than for purposes of resale or rental) all equipment manufactured by Graco and bearing its name
to be free from defects in material and workmanship if operated in accordance with Graco’s printed recommendations and instructions. This
warranty applies for one year from the date of purchase.
This warranty does not cover and Graco shall not be liable for general wear and tear, or any malfunction, damage, or wear caused by improper
use, accidents, user negligence, use of non-Graco component parts or service or repair performed by anyone other than a Graco authorized
service center.
IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO
ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE.
GRACO SHALL NOT IN ANY EVENT BE LIABLE FOR INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE OR EXPENSE OF
ANY KIND, WHETHER FROM BREACH OF THIS WARRANTY OR ANY OTHER REASON. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
To make a claim under this warranty, return the product with proof of purchase, transportation prepaid, to any Authorized Graco Service Center.
Graco’s Authorized Service Center, at its option, will either repair or replace the product and return it to you, postage, prepaid. To find the nearest
Graco Authorized Service Center call 1-888-541-9788 or visit our website at www.Graco.com
This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.
All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the
right to make changes at any time without notice.
This Manual contains English: MM 309797
Sales Office: Minneapolis
International Offices: Belgium, Korea, China, Japan
Written in USA 1/2003, Rev. 9/2006
26
309797P
Download PDF