Advantech | ACP-2010MB | User manual | Advantech ACP-2010MB User manual

ACP-2010MB
2U-High Rackmount Chassis for
ATX / MicroATX Motherboard
User Manual
Copyright
The documentation and the software included with this product are copyrighted 2006 by Advantech Co., Ltd. All rights are reserved. Advantech
Co., Ltd. reserves the right to make improvements in the products
described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or
by any means without the prior written permission of Advantech Co., Ltd.
Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use,
nor for any infringements of the rights of third parties, which may result
from its use.
Acknowledgements
Intel®, Pentium® 4, and Celeron® are trademarks of Intel Corporation.
The ACP-2010, AIMB-764, AIMB-762, AIMB-760, AIMB-750, AIMB744, AIMB-742, AIMB-740, AIMB-562, AIMB-560, AIMB-552,
AIMB-550, are trademarks of Advantech Co., Ltd. All other product
names or trademarks are the properties of their respective owners.
On-line Technical Support
For technical support and service, please visit our support website at:
http://www.advantech.com/support
Part No. 2002201000
1st Edition
Printed in China
January 2007
ACP-2010MB User Manual
ii
Safety Instructions
1.
Read these safety instructions carefully
2.
Keep this user manual for later reference.
3.
Disconnect this equipment from AC outlet before cleaning. Do not
use liquid or spray detergents for cleaning.
4.
For pluggable equipment, the power outlet shall be installed near
the equipment and shall be easily accessible.
5.
Keep this equipment away from humidity.
6.
Put this equipment on a reliable surface during installation. Dropping it or letting it fall could cause damage.
7.
Do not leave this equipment in an environment unconditioned
where the storage temperature under 0° C (32° F) or above 40° C
(104° F), it may damage the equipment.
8.
The openings on the enclosure are for air convection hence protects
the equipment from overheating. DO NOT COVER THE OPENINGS.
9.
Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.
10.
Place the power cord such a way that people can not step on it. Do
not place anything over the power cord. The voltage and current
rating of the cord should be greater than the voltage and current rating marked on the product.
11.
All cautions and warnings on the equipment should be noted.
12.
If the equipment is not used for long time, disconnect it from the
power source to avoid being damaged by transient over-voltage.
13.
Never pour any liquid into ventilation openings. This could cause
fire or electrical shock.
14.
Never open the equipment. For safety reasons, the equipment
should be opened only by qualified service personnel.
15.
If any of the following situations arises, get the equipment checked
by service personnel:
a.
The power cord or plug is damaged.
b.
Liquid has penetrated into the equipment.
c.
The equipment has been exposed to moisture.
iii
d.
The equipment does not work well or you cannot get it to
work according to user manual.
e.
The equipment has been dropped and damaged.
f.
The equipment has obvious signs of breakage.
16.
CAUTION: The computer is provided with a battery-powered realtime clock circuit. There is a danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacture. Discard used batteries according to the
manufacturer's instructions.
17.
THE COMPUTER IS PROVIDED WITH CD DRIVES COMPLY
WITH APPROPRIATE SAFETY STANDARDS INCLUDING
IEC 60825.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
18.
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
19.
CAUTION: Always completely disconnect the power cord from
your chassis whenever you work with the hardware. Do not make
connections while the power is on. Sensitive electronic components
can be damaged by sudden power surges.
20.
CAUTION: Always ground yourself to remove any static charge
before touching the motherboard, backplane, or add-on cards. Modern electronic devices are very sensitive to static electric charges.
As a safety precaution, use a grounding wrist strap at all times.
Place all electronic components on a static-dissipative surface or in
a static-shielded bag when they are not in the chassis.
21.
CAUTION: Any unverified component could cause unexpected
damage. To ensure the correct installation, please always use the
components (ex. screws) provided with the accessory box.
ACP-2010MB User Manual
iv
A Message to the Customer
Advantech customer services
Each and every Advantech product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new Advantech
equipment is destined for the laboratory or the factory floor, you can be
assured that your product will provide the reliability and ease of operation
for which the name Advantech has come to be known. Your satisfaction
is our primary concern. Here is a guide to Advantech’s customer services.
To ensure you get the full benefit of our services, please follow the
instructions below carefully.
Technical support
We want you to get the best performance possible from your products. If
you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones
we can give over the phone.
Please consult this manual first. If you still cannot find the answer, gather
all the information or questions that apply to your problem, and with the
product close at hand, call your dealer. Our dealers are well trained and
ready to give you the support you need to get the most from your Advantech products. In fact, most problems reported are minor and can be easily
solved over the phone.
In addition, free technical support is available from Advantech engineers
every business day. We are always ready to give advice about application
requirements or specific information on the installation and operation of
any of our products.
v
Product Warranty
Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years
from the date of purchase.
This warranty does not apply to any products which have been repaired or
altered by persons other than repair personnel authorized by Advantech,
or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as
a consequence of such events.
If an Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you will
be billed according to the cost of replacement materials, service time and
freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1.
Collect all the information about the problem encountered, forexample, type of PC, CPU speed, Advantech products used, other
hardware and software used, etc. Note anything abnormal and list
any on-screen messages you get when the problem occurs.
2.
Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available.
3.
If your product is diagnosed as defective, obtain an RMA (return
material authorization) number from your dealer. This allows us to
process your return more quickly.
4.
Carefully pack the defective product, a fully-completed Repairand
Replacement Order Card and a photocopy proof of purchase date
(such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for warranty service.
5.
Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.
ACP-2010MB User Manual
vi
Initial Inspection
When you open the carton, please make sure that the following materials
have been shipped:
•
•
•
•
ACP-2010MB Chassis
User Manual
Warranty Card
Accessory box with a package of screws (for fastening the motherboard, optical disk drive, other disk drives, ear handles, etc.), a pair
of keys, a USB cap, a PS/2 cap, a stand-off bracket, a pair of ear
handles.
If any of these items are missing or damaged, contact your distributor or
sales representative immediately. We have carefully inspected the ACP2010MB mechanically and electrically before shipment. It should be free
of marks and scratches and in perfect working order upon receipt. As you
unpack the ACP-2010MB, check it for signs of shipping damage. (For
example, damaged box, scratches, dents, etc.) If it is damaged or it fails to
meet the specifications, notify our service department or your local sales
representative immediately. Also, please notify the carrier. Retain the
shipping carton and packing material for inspection by the carrier. After
inspection, we will make arrangements to repair or replace the unit.
vii
Contents
Chapter
1 General Information ........................................2
1.1
1.2
1.3
Introduction ....................................................................... 2
Specifications .................................................................... 2
Power Supply Options....................................................... 3
1.4
Environment Specifications .............................................. 4
1.5
Dimension Diagram .......................................................... 5
Table
Table
1.1 Power supply options................................ 3
1.2 Environment specifications ...................... 4
Figure 1.1 Dimension diagram................................... 5
Chapter
2 System Setup.....................................................8
2.1
Removing the Chassis Cover ............................................ 8
2.2
Installing the Motherboard ................................................ 9
Figure 2.1 Removing the chassis top cover ............... 8
Figure 2.2 Yellow label indicating copper stub
locations ................................................. 9
Figure 2.3 Stand-off bracket .................................... 10
Figure 2.4 Installing a motherboard......................... 10
2.3
Installing Riser Card and Add-on Card........................... 11
Figure 2.5 Installing the riser card ........................... 11
Figure 2.6 Installing the add-on card ....................... 11
2.4
Installing Disk Drives...................................................... 12
2.4.1
2.5
Installing HDD, Optical Disk Drive, and FDD ............ 12
Figure 2.7 Installing the internal HDD .................... 12
Figure 2.8 Installing the optical disk drive and 3.5"
FDD...................................................... 13
Attaching the Ears and Handles ...................................... 14
Figure 2.9 Attaching the ears and handles ............... 14
Chapter
3 Operation ........................................................16
3.1
The Front Panel ............................................................... 16
3.1.1
3.1.2
3.2
Figure 3.1 Front panel with door closed .................. 16
Figure 3.2 Front panel with door open..................... 16
Switch, Button and I/O Interfaces................................. 16
LED Indicators for System Status ................................ 17
Table 3.1 LED indicator functions ......................... 17
The Rear Panel ................................................................ 18
Figure 3.3 Rear panel with standard I/O brackets.... 18
Figure 3.4 Rear panel with low profile I/O brackets 18
3.3
Replacing the Cooling Fan.............................................. 19
3.3.1
Replacing the fan .......................................................... 19
Figure 3.5 Replacing the cooling fan ....................... 19
ix
3.4
Cleaning the Filters ......................................................... 20
3.5
Replacing the Power Supply ........................................... 21
Figure 3.6 Replacing the filters................................ 20
3.5.1
Chapter
Replacing the Power Supply......................................... 21
Figure 3.7 Replacing the power supply ................... 21
4 Alarm Module.................................................24
4.1
Alarm Board Layout........................................................ 24
4.2
Alarm Board Specifications ............................................ 25
Figure 4.1 Alarm board layout................................. 24
4.2.1
4.3
Switch Settings................................................................ 28
4.3.1
4.4
Connectors & Pin Definition ........................................ 25
Table 4.1 CN1, Auxiliary external power connector,
standard mini 4-Pin power connector ..25
Table 4.2 CN4, Thermal sensor (LM75) connector 25
Table 4.3 CN13, Voltage detect. input connector .. 26
Table 4.4 CN16, Power good input connector ....... 26
Table 4.5 CN17, Alarm reset connector ................. 26
Table 4.6 CN18, Output connector to LED board.. 26
Table 4.7 CN26, HDD LED connector .................. 26
Table 4.8 FAN1~FAN7, Fan connectors................ 26
Table 4.9 J1, External buzzer ................................. 27
Table 4.10 SW1, Fan number select switch ............. 27
Fan Number Setting ...................................................... 28
Table 4.11 SW2, Fan number setting ....................... 28
Thermal Sensor ............................................................... 29
Figure 4.2 Thermal sensor location.......................... 29
Figure 4.3 Thermal sensor module .......................... 29
Table 4.12 CN1 & CN2, Temperature sensor
connector .............................................. 30
Table 4.13 SW2, Thermal sensor I.D. setting........... 30
Appendix A Exploded Diagram and Parts List ................32
Figure A.1 Exploded diagram................................... 32
Table A.1 Parts List ................................................. 32
Appendix B Motherboard and Riser Card Options.........34
B.1
Motherboard Options ...................................................... 34
Table
Table
B.2
B.1 ATX motherboard options...................... 34
B.2 MicroATX motherboard options ............ 35
Riser Card Options .......................................................... 35
Table
B.3 Riser card options ................................... 35
CHAPTER
1
General Information
Chapter 1
General Information
1.1 Introduction
The ACP-2010MB is a 2U-high rackmount industrial computer chassis.
It meets a variety of application needs for filing, printing, e-mails and
webserving. This powerful computing platform is suitable for missioncritical computer telephony applications, industrial automation, and factory management. A wide range of standard computing peripherals can be
integrated with the chassis to meet different application needs for operation under harsh conditions 24 hours a day, 7 days a week.
1.2 Specifications
•
•
•
•
•
•
•
•
•
•
•
Construction: Heavy-duty steel
Disk Drive Capacity: One 5.25" disk drive bay and three 3.5" disk
drive bay (for FDD or internal HDD)
LED Indicators on Front Panel: Bi-color LEDs (green/red) for
Power, Temperature, and Fan status; single-color LEDs (green) for
HDD activity.
Switch and Buttons on Front Panel: Power switch, System Reset
button and Alarm Reset button.
Front I/O Interfaces: Dual USB ports and PS/2 connector
Rear I/O Interfaces: Reserved two 9-pin D-SUB openings
Security Protection: The storage system, power switch, system
reset button and alarm reset button are all behind the lockable door.
Cooling System: Two 8 cm x 8 cm (47 CFM) hot-swappable cooling fans.
Air Filters: Two easily maintained reusable filters near the front of
the system fan and behind the front door.
Weight: 13 kg (28.6 lbs)
Dimensions (W x H x D): 482 x 88 x 480 mm (19" x 3.46" x 18.9")
ACP-2010MB User Manual
2
1.3 Power Supply Options
Table 1.1: Power supply options
Model Name
Watt
Input rating
1757000007G
1757000105G
300 W (ATX, PFC)
(single PS/2)
400 W (ATX, PFC)
(single PS/2)
100 ~ 240 Vac
(Full range)
100 ~ 240 Vac
(Full range)
Output voltage
+5V @ 35A, +3.3V @ 20A, +5V @ 25A, +3.3V @ 20A,
+12V @ 16A, -5V @ 0.5A, +12V @ 28A, -5V @ 0.5A,
-12V @ 1A, +5Vsb @ 2A -12V @ 0.5A, +5Vsb @ 2A
Minimum load
+5V @ 3A, +3.3 V @ 1A,
+5V @ 3A, +3.3 V @ 1A,
+12V @ 2A, -5V @ 0.05A,
+12V @ 2A, +5Vsb @ 0.1A
-12V @ 0.05A, +5Vsb @ 0.1A
MTBF
97,800 hours @ 25° C
100,000 hours @ 25°C
Safety
UL/TUV/CB/CCC
UL/TUV/CB/CCC
3
Chapter 1
1.4 Environment Specifications
Table 1.2: Environment specifications
Environment
Operating
Non-operating
Temperature
0 to 40°C (32 to 104°F)
-20 to 60°C (-4 to 140°F)
Humidity
10 to 85% @ 40°C,
non-condensing
10 to 95% @ 40°C,
non-condensing
Vibration
1G rms
2G
10G with 11 ms duration,
half sine wave
30G
Shock
Altitude
0 to 3,048 m (0 ~ 10,000 ft)
CE compliant
Safety
ACP-2010MB User Manual
4
1.5 Dimension Diagram
unit: mm [inch]
Figure 1.1: Dimension diagram
5
Chapter 1
CHAPTER
System Setup
2
Chapter 2
System Setup
The following procedures instruct users to install a motherboard, add-on
cards, and disk drives into the ACP-2010MB. Refer to Appendix A, the
Exploded Diagram and the Parts List for more detailed information about
the parts of the ACP-2010MB.
Note:
Use caution when installing or operating
the components with the chassis open. Be
sure to turn off the power, unplug the power
cord and ground yourself by touching the
metal chassis before you handle any components inside the machine.
2.1 Removing the Chassis Cover
To remove the cover, please proceed as below.
1.
Loosen six screws on the rear and both sides of the top cover.
2.
Pull the L-type chassis top cover backwards and then lift it up.
Figure 2.1: Removing the chassis top cover
ACP-2010MB User Manual
8
2.2 Installing the Motherboard
To install the motherboard, please proceed as follows:
Note:
1.
Use caution when installing a motherboard. It's
highly recommended to integrate the Advantech
motherboard series with the ACP-2010MB to
ensure the quality, safety and smooth operation
of the air flow design.
A yellow label is located inside of the chassis bottom. (see Figure
2.2) The label shows the stand-off bracket locations for attaching
specific Advantech motherboards.
A
M
AIMB-744
AIMB-750
AIMB-760
AIMB-740
AIMB-742
AIMB-762
AIMB-764
AIMB-542
AIMB-554
AIMB-556
AIMB-560
AIMB-562
The STAND-OFF bracket is in
the accessory box.Be sure
to attach the necessary
bracket on the chassis .
Figure 2.2: Yellow label indicating copper stub locations
9
Chapter 2
2.
3.
4.
5.
Users can find the stand-off bracket (see Figure 2.3) in the accessory box. Be sure to follow the instruction and fasten the motherboard onto the chassis with the stand-off bracket locations.
Attach the motherboard I/O shielding onto the rear plate first. Then
fasten the motherboard onto the chassis. (see Figure 2.4)
Connect the 20-pin (or 24-pin) ATX power connector and the 4-pin
+12V power connector from the power supply to the motherboard
Connect the 9-pin USB wire, PS/2 wire, Power switch wire, and the
System Reset switch wire from the chassis to the motherboard.
Figure 2.3: Stand-off bracket
Figure 2.4: Installing a motherboard
ACP-2010MB User Manual
10
2.3 Installing Riser Card and Add-on Card
ACP-2010MB supports up to 3 add-on cards. To install the add-on card,
please install a riser card first. The process is as follows:
1.
2.
3.
Insert the riser card on the motherboard. Then, attach it onto the
beam on the chassis by fastening the two screws. (see Figure 2.5)
Remove the corresponding I/O bracket attached to the rear plate of
the chassis. Insert an add-on card vertically into the proper slot on
the riser card. For full-length cards, please make sure that the card
bracket has been inserted properly and the other edge of the card
has been inserted into the plastic guiding fillister. Then fasten the
screws on the top of the I/O bracket. (see Figure 2.6)
Repeat Step 2 if there is more than one add-on card to be installed.
Figure 2.5: Installing the riser card
Figure 2.6: Installing the add-on card
Note:
If the chassis with the low profile I/O bracket on
the rear plate is used, a riser card is not needed.
11
Chapter 2
2.4 Installing Disk Drives
The ACP-2010MB supports one 5.25" optical disk drive and three 3.5"
disk drives (one FDD and two internal HDD). Please refer to the following instructions to install the various disk drives.
2.4.1
Installing HDD, Optical Disk Drive, and FDD
To install the internal HDD, 5.25" optical disk drive and the 3.5" FDD,
please follow these steps for installation:
1.
2.
3.
To install the 3.5" internal HDD, simply release the four screws on
top of the disk drive bracket.
Insert the disk drive into the proper location in the bracket and
secure them with the screws provided. (see Figure 2.7)
Return the bracket with the disk drive in the original position and
fasten it with the screws.
Figure 2.7: Installing the internal HDD
ACP-2010MB User Manual
12
4.
5.
6.
7.
To install the optical disk drive and 3.5" FDD, undo the screws on
the 5.25" disk drive bracket.
Undo the screws on each side of the 5.25" disk drive bracket to
remove the front covers.
Slide the optical disk drive and the FDD into the bracket and fasten
it on both sides with the eight screws provided. (see Figure 2.9)
Return the 5.25" disk drive bracket with the disk drives in the original position and reattach it inside the chassis with the original
screws.
Connect the suitable IDE or SATA cables from the motherboard to
the 3.5" internal HDD, the optical disk drive, or an FDD. Then,
plug the power connector into each disk drive.
Figure 2.8: Installing the optical disk drive and 3.5" FDD
13
Chapter 2
2.5 Attaching the Ears and Handles
A pair of ears and a set of handles in the accessory box, which may be
added to the front end of the chassis for easy handling.
To install the handles onto the chassis, refer to Figure 2.9 and attach the
ears to the chassis, and the handles to the ears on the front-right and frontleft edges with the screws provided.
Figure 2.9: Attaching the ears and handles
ACP-2010MB User Manual
14
CHAPTER
Operation
3
Chapter 3
Operation
3.1 The Front Panel
The front panel features the lockable door and four LED indicators. It
provides front accessible, dual USB ports and a PS/2 connector. The front
door can be closed with or without the key using the user-friendly rotary
lock. Behind the opening door is a Momentary Power switch, a System
Reset button, and an Alarm Reset button. Specific functions are described
as below.
POWER
HDD
TEMP
FAN
Figure 3.1: Front panel with door closed
POWER
HDD
TEMP
FAN
Figure 3.2: Front panel with door open
3.1.1
Switch, Button and I/O Interfaces
Momentary Power switch: Press this switch to turn the system power on
or off. Please use the system shutdown or press this switch for few seconds to turn off the system ATX power.
Alarm Reset button: Whenever a fault occurs in the system (e.g., fan
failure or chassis overheating) the audible alarm will be activated. Pressing this button will stop the alarm from beeping.
System Reset button: Press this button to reboot the system.
Dual USB port: For connecting a wide range of USB devices for data
transfer, backup or input.
PS/2 connector: For connecting a keyboard or mouse depending on the
motherboard design.
ACP-2010MB User Manual
16
3.1.2
LED Indicators for System Status
Four LEDs are placed on the left side of the front panel to indicate system
health and activity. Refer to Table 3.1 for the LED definition summary.
Table 3.1: LED indicator functions
LED
Description
Green
Red
System power
Normal
Abnormal
Hard disk drive activity
Data access
No light
Temperature
Temperature in the
chassis
Normal
Abnormal
Fan
Cooling fan status
Normal
Abnormal
Power
Hard Disk
When the system power is on, the power LED is always Green.
When the power LED is RED, it indicates a redundant power supply
module failure. To stop the alarm beep, press the Alarm Reset button.
Examine the redundant power supply module right away and replace the
failed module with a working one.
When the fan LED is RED, it indicates a failed cooling fan, and the alarm
is also activated. To stop the alarm beep, press the Alarm Reset button
and then replace the failed fan with a working one immediately.
If the temperature LED is RED, it means that inside of the chassis is
overheated (more than 50°C). An audible alarm will be activated. To stop
the alarm beep, press the Alarm Reset button. Inspect the fan filter and
the rear section of the chassis immediately. Make sure the airflow inside
the chassis is smooth and not blocked by dust or other particles.
17
Chapter 3
3.2 The Rear Panel
The rear panel includes with 3-slot I/O brackets, two reserved 9-pin DSUB openings and a motherboard I/O opening. (see Figure 3.3)
Figure 3.3: Rear panel with standard I/O brackets
There is an optional rear I/O bracket for the low profile I/O cards. (see
Figure 3.4)
Figure 3.4: Rear panel with low profile I/O brackets
There is a ground screw with a washer located on the lower right of the
rear panel. This will protect the system in case of electrical leakage.
ACP-2010MB User Manual
18
3.3 Replacing the Cooling Fan
There are two easily maintained system cooling fans in the chassis. The
fans provide the system with ample cooling by blowing air toward the
rear.
To replace the fan, proceed as follows:
3.3.1
1.
2.
3.
4.
5.
6.
7.
8.
Replacing the fan
Remove the top cover.
Remove the 3.5" HDD cage so that the power connectors can be
unplugged from the fans.
Loosen the two screws on the fan bracket and gently pull it out.
Loosen four screws on the fan in the bracket. Remove the broken
fan and replace it with a working one.
Fix the working fan onto the bracket with the four screws. (see Figure 3.5)
Replace the entire fan unit into the chassis by tightening the two
screws and reconnect the fan power connectors.
Return the 3.5" HDD cage and tighten the four screws.
Replace the top cover and fasten it.
Figure 3.5: Replacing the cooling fan
19
Chapter 3
3.4 Cleaning the Filters
The filter functions to block dust or particles from the work environment
and greatly helps to extend the longevity of the system. It's better to
check, clean and replace the filters periodically. Two reusable, washable
filters are located behind the front door and in front of the system fans.
To remove and clean the filter, proceed as follows:
1.
2.
3.
4.
Open the front door.
Loosen the two screws on the filter bracket. Then pull out the filter
to clean it, or replace it with a fresh one.
To pull out the fan filter, push the hook and slide it rightwards. (see
Figure 3.6) Clean the filter with a soft brush or wash the dust away
from the filter with fluent water and let it dry thoroughly.
Replace them inside the unit.
Figure 3.6: Replacing the filters
ACP-2010MB User Manual
20
3.5 Replacing the Power Supply
The ACP-2010MB supports either a 300W or a 400W PS/2 power supply.
To replace the power supply, proceed as follows:
3.5.1
1.
2.
3.
4.
5.
6.
7.
Replacing the Power Supply
Unplug the power cord from the power supply.
Remove the top cover.
Unplug the 20-pin (or 24-pin) ATX power connector and 4-pin
+12V power connector from the motherboard, as well as the power
connectors from all disk drives.
Loosen the three screws on the rear plate and the two screws on the
power supply bracket and gently remove it. (see Figure 3.7)
Replace the power supply with a new one and fasten it onto the
chassis.
Plug in the 20-pin (or 24-pin) ATX power connector and the 4-pin
+12V power connector to the motherboard. Plug the other power
connectors to the disk drives and peripherals.
Replace the top cover. Then plug in the power cord.
Figure 3.7: Replacing the power supply
21
Chapter 3
CHAPTER
Alarm Module
4
Chapter 4
Alarm Module
The alarm module is located under the 3.5" disk drive bay. The alarm
module provides System Detection functions that monitor the entire status
of the computer system, including: thermal conditions, fans, power supply and HDD operation. Any problems with the system are reported
through audible alarms and LED indicators.
The alarm module sounds an audible alarm whenever:
1.
2.
3.
Any power supply module of the redundant power supply fails;
One of the system cooling fans fails;
The internal temperature of the chassis becomes too high.
To stop the alarm beep, press the Alarm Reset button on the front panel
and then take the necessary action to fix it.
4.1 Alarm Board Layout
The layout and detailed specifications for connectors on the alarm board
are shown in this diagram:
Figure 4.1: Alarm board layout
ACP-2010MB User Manual
24
4.2 Alarm Board Specifications
Input Power: +5V, +12V
Input Signals:
•
•
•
•
•
•
7 “fan” connectors
One “thermal sensor” connector (supports up to 8 thermal sensors
connected in a series)
One “power good” input
One “alarm reset” input
One “voltage signal” connector (connected from the motherboard,
and supports six voltages: +- 12V, +- 5V, +3.3V, +5Vsb)
One “hard disk LED” connector (connected from the motherboard)
Output Signals:
•
•
4.2.1
One “LED board” connector
One “buzzer” output
Connectors & Pin Definition
Table 4.1: CN1, Auxiliary external power connector, standard mini 4Pin power connector
Pin 1
+12V
Pin 3
GND
Pin 2
GND
Pin 4
+5V
Table 4.2: CN4, Thermal sensor (LM75) connector
Pin 1
+5V
Pin 3
T_SDAT
Pin 2
T_SCLK
Pin 4
GND
25
Chapter 4
Table 4.3: CN13, Voltage detect. input connector
Pin 1
+5Vsb
Pin 5
+5V
Pin 2
GND
Pin 6
+3.3V
Pin 3
GND
Pin 7
-12V
Pin 4
-5V
Pin 8
+12V
Table 4.4: CN16, Power good input connector
Pin 1
Power Good
Pin 2
GND
Pin 2
GND
Table 4.5: CN17, Alarm reset connector
Pin 1
ALARM RESET
Table 4.6: CN18, Output connector to LED board
Pin 1
GND
Pin 9
Temperature
Good
Pin 2
+5V signal
Pin 10
Temperature Fail
Pin 3
+12V signal
Pin 11
FAN Good
Pin 4
-5V signal
Pin 12
FAN Fail
Pin 5
-12V signal
Pin 13
N/A
Pin 6
HDD_1
Pin 14
+3.3V signal
Pin 7
Power Good
Pin 15
+5Vsb signal
Pin 8
Power Fail
Pin 2
N/A
Pin3
FAN_DEC
Table 4.7: CN26, HDD LED connector
Pin 1
HLED_ACT
Table 4.8: FAN1~FAN7, Fan connectors
Pin 1
GND
Pin 2
+12V
ACP-2010MB User Manual
26
Table 4.9: J1, External buzzer
Pin 1
Buzzer
Pin 2
+5V
Table 4.10: SW1, Fan number select switch
Pin 1
GND
Pin 5
GND
Pin 2
FAN_SEL1
Pin 6
FAN_SEL3
Pin 3
GND
Pin 7
GND
Pin 4
FAN_SEL2
Pin 8
RESET
27
Chapter 4
4.3 Switch Settings
4.3.1
Fan Number Setting
Table 4.11: SW2, Fan number setting
Fan Number
SW 1-1
SW 1-2
SW 1-3
SW 1-4
0
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
2 (default)
OFF
ON
OFF
OFF
3
ON
ON
OFF
OFF
4
OFF
OFF
ON
OFF
5
ON
OFF
ON
OFF
6
OFF
ON
ON
OFF
7
ON
ON
ON
OFF
Note:
Connect the fan connectors in the correct
sequence: if two fans are set on SW1, the
correct method is to connect them into connectors FAN1 and FAN2. If the two fans
are connected to other fan connectors,out
of sequence, such as FAN1 and FAN3 or
FAN2 and FAN3 or FAN3 and FAN4,
instead of FAN1 and FAN2, then the alarm
will not function correctly.
ACP-2010MB User Manual
28
4.4 Thermal Sensor
The ACP-2010MB is configured with a thermal sensor on the backside of
the chassis. (see Figure 4.2)
Thermal sensor
Figure 4.2: Thermal sensor location
Refer to Figure 4.3 for a diagram of the thermal sensor module layout.
Figure 4.3: Thermal sensor module
Users can set up to 8 thermal sensors. The default sensor I.D. number is
1. User can refer to Table 4.13 to set the sensor I.D. number by adjusting
the switch, SW1, on the sensor module.
29
Chapter 4
Table 4.12: CN1 & CN2, Temperature sensor connector
Pin 1
+5V
Pin 3
T_SDAT
Pin 2
T_SCLK
Pin 4
GND
Table 4.13: SW2, Thermal sensor I.D. setting
Sensor I.D.
No.
SW 1-1
SW 1-2
SW 1-3
SW 1-4
0
ON
ON
ON
ON
1 (default)
OFF
OFF
OFF
ON
2
OFF
OFF
ON
ON
3
OFF
ON
OFF
ON
4
OFF
ON
ON
ON
5
ON
OFF
OFF
ON
6
ON
OFF
ON
ON
7
ON
ON
OFF
ON
ACP-2010MB User Manual
30
APPENDIX
A
Exploded Diagram and
Parts List
Appendix A Exploded Diagram and Parts
List
Figure A.1: Exploded diagram
Table A.1: Parts List
1
Front panel
13 Rackmount ear
25 Chassis spot
2
LED
14 Front module
cover
26 HDD bay
3
Door filter
15 FDD cover
27 M4 cushion
4
Rotary lock
16 CD-ROM cover
28 Front cover
5
Filter cover
17 Drive bay
29 KB/USB board
6
Small door
18 Chassis body
30 Thermal board
7
Door hinge right
19 Power bracket
31 Guide rail bracket
8
Door hinge left
20 Power supply
32 PCB guide rail
9
Power button
21 Rear plate
33 Card support
beam
10 Reset button
22 Top cover
34 Cooling fan
11 Filter housing
23 I/O bracket
35 Fan bracket
12 Handle
24 Spacer bracket
ACP-2010MB User Manual
32
APPENDIX
B
Motherboard and
Riser Card Options
Appendix B Motherboard and Riser Card
Options
B.1 Motherboard Options
The ACP-2010MB supports a variety of Advantech ATX / MicroATX
motherboards described below. Contact a local sales representative for
more detailed information.
Table B.1: ATX motherboard options
Bus
Model Name
AIMB-764
AIMB-762
AIMB-760
AIMB-750
AIMB-744
PCI
PCI/ISA
ISA
AGP
SATA
-
-
-
5
-
-
-
4
-
-
-
4
-
-
1 (4X)
2
-
-
1 (8X)
2
1 (PCIe x16)
1 (PCIe x4)
5 (PCI 32-bit)
1 (PCIe x16)
1 (PCIe x4)
5 (PCI 32-bit)
1 (PCIe x1)
5 (PCI 32-bit)
2 (PCI-X 64-bit)
4 (PCI 32-bit)
2 (PCI-X 64-bit)
4 (PCI 32-bit)
AIMB-742
4 (32-bit)
1
1
1 (8X)
-
AIMB-740-B
4 (32-bit)
1
1
-
-
AIMB-7406CB1
5 (32-bit)
-
-
-
-
ACP-2010MB User Manual
34
Table B.2: MicroATX motherboard options
Bus
Model Name
AIMB-560
AIMB-556
AIMB-554
PCI
AGP
SATA
3 (32-bit)
-
4
-
4
-
4
1 (PCIe x16)
1 (PCIe x4)
2 (PCI 32-bit)
1 (PCIe x16)
1 (PCIe x4)
2 (PCI 32-bit)
B.2 Riser Card Options
The riser card is specially designed to support Advantech AIMB series of
motherboards except AIMB-562 & AIMB-542.
Table B.3: Riser card options
Model Name
Interface
Expansion
Slots
Compatible motherboards
AIMB-R430103A1E
PCIe x4
3 PCIe x1
AIMB-764 / 556
AIMB-R430P03A1E
PCIe x4
3 PCI
AIMB-764 / 762 / 556 / 554
AIMB-RP30P03A1E
PCI
3 PCI
AIMB-760 / 750 / 744 / 742 /
740 / 560 / 556
AIMB-RH31P12A1E
PCI +
PCIe x1
2 PCI +
1 PCIe x1
AIMB-760
35
Appendix B
Download PDF