Minitar | MWIPC-1510WG | User manual | Minitar MWIPC-1510WG User manual

MWIPC-1510WG User Manual
MWIPC-1510WG
Internet Camera
User’s Manual
Version: 1.0
Released Date: March 2007
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
MWIPC-1510WG User Manual
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
MWIPC-1510WG User Manual
Contents
1.
2.
3.
4.
5.
6.
Introduction.......................................................................................................... 1
Package Content ................................................................................................. 1
System Requirement ........................................................................................... 1
Hardware Installation ........................................................................................... 2
4.1.
LED and Focusing ............................................................................................ 2
4.2.
Camera Ports .................................................................................................... 3
4.3.
Installation Procedure ....................................................................................... 4
Software Installation ............................................................................................ 5
Using the Administrator Utility ........................................................................... 11
6.1.
General Setting ............................................................................................... 12
6.2.
Detail Setting .................................................................................................. 14
6.2.1.
Network Setting....................................................................................... 15
6.2.2.
Wireless Settings (*Wireless Model Only) .............................................. 17
6.2.3.
E-Mail Setting.......................................................................................... 19
6.2.4.
PPPoE Settings ...................................................................................... 21
6.2.5.
FTP Settings ........................................................................................... 22
6.2.6.
Date / Time Settings ............................................................................... 23
6.2.7.
Resolution ............................................................................................... 24
6.2.8.
Advanced Setting .................................................................................... 25
6.2.9.
Users....................................................................................................... 26
6.2.10.
Tools ....................................................................................................... 27
6.2.11.
About....................................................................................................... 29
6.3.
7.
Setting Wizard ................................................................................................ 29
Using the Camera Viewer.................................................................................. 32
7.1.
Panel Introduction ........................................................................................... 32
7.2.
Camera Buttons .............................................................................................. 33
7.3.
Camera Status ................................................................................................ 34
7.4.
Control Buttons ............................................................................................... 34
7.5.
Video Recording ............................................................................................. 36
7.6.
Change Resolution ......................................................................................... 36
7.7.
View Four Cameras Simultaneously ............................................................... 37
7.8.
Viewer Utility Setting ....................................................................................... 38
7.8.1.
Setting ..................................................................................................... 39
7.8.2.
Recording................................................................................................ 40
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
MWIPC-1510WG User Manual
8.
7.8.3.
Status ...................................................................................................... 43
7.8.4.
General ................................................................................................... 44
7.8.5.
About....................................................................................................... 46
7.9.
Playback ......................................................................................................... 47
7.10.
Rotate Video ................................................................................................... 49
Web Connection and Setup............................................................................... 50
8.1.
Camera Setting ............................................................................................... 53
8.2.
LAN Setting ..................................................................................................... 55
8.3.
WLAN ............................................................................................................. 58
8.4.
E-Mail and FTP ............................................................................................... 61
8.5.
Motion Detection ............................................................................................. 62
8.6.
System ............................................................................................................ 63
8.7.
Status .............................................................................................................. 65
8.8.
Users .............................................................................................................. 65
8.9.
Log .................................................................................................................. 66
Frequently Asked Questions..................................................................................... 67
9. Technical Specifications .................................................................................... 68
10. Appendix A Router/Gateway Setup for Internet Viewing ................................... 69
11. Appendix B Set up WLAN step by step ............................................................. 71
12. Appendix C Viewing via UPnP in Windows XP ................................................. 77
13. Appendix D Configure Windows 2003 Server ................................................... 81
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
MWIPC-1510WG User Manual
1.
Introduction
Thank you for choosing the Minitar Internet Camera. This Internet Camera sends live
video through 10/100Mbps wired network to a web browser or camera viewer across Internet
anywhere in the world! This compact, self-contained unit lets you keep an eye on your home,
your kids, and your workplace—whatever’s important to you.
How does the Camera do all of this? Unlike standard “web cams” that require an
attached PC, the Internet Camera can connect directly to a network. The MJPEG video
compression produces a high quality, high-frame rate, 640 x 480 video stream.
The included Camera Viewer utility lets you record the video to your local hard drive,
“live” or on a predetermined schedule.
Use the instructions in this Guide to help you integrate the Camera into your network.
These instructions should be all you need to get the most out of the Internet Camera.
2.
Package Content
„
One Internet Camera
„
One Power Adapter
„
One Camera Stand
„
One 100M Category 5 Ethernet Cable
„
One Quick Installation Guide
„
One CD (Including Manual/Utility/Driver)
„
One Antenna(*Wireless Model Only)
If any of the above items are missing, please contact your supplier.
3.
System Requirement
System requirement for PC, MAC or Notebook PC to access the Internet Camera are:
„
OS System: Windows 98 , ME , 2000, XP + SP2, Server 2003
„
IE Version: 6.0.29 + SP2
„
CPU: Intel Pentium III 750MHz above or Intel Celeron 1GHz above
„
Memory Size: 128MB (256MB recommended)
„
DirectX 9.0 or above
or above
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
1
MWIPC-1510WG User Manual
„
VGA card with fully DirectX 9.0 supported.
„
VGA Card Resolution: 800 x 600 or above
4.
Hardware Installation
4.1.
LED and Focusing
The Camera head and its focus ring allow you to modify the aim and focus of the Camera.
To adjust the Camera’s focus, rotate the dark focus ring.
There are three LEDs indicating the camera status and networking status.
y
Power
When the camera is power on, the LED will light.
y
LAN
When the Internet Camera is linking to wired network, the LED is lighting. The LED is
flashing when video is transmitted or received through wired network.
y
WLAN
When the Internet Camera is linking to wireless network, the LED is lighting. The LED is
flashing when video is transmitted or received through wireless network.
Wireless SMA Connector
(Wireless Model Only)
LED Green:
LAN Activity
Focus Ring
LED Amber:
WLAN Activity
LED Blue:
Power On
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
2
MWIPC-1510WG User Manual
4.2.
Camera Ports
The Camera features three ports and a Reset button.
y
Power
The Power port is where you can connect the power adapter.
y
LAN
The LAN port is where you can connect the Ethernet network cable.
y
WLAN (Antenna Connector)
This round connection is standard Reverse SMA connector where any antennas with
Reverse SMA connector can connect to the Internet Camera..
y
Reset
1.
If problems occur with your Internet Camera, press the reset button with a
pencil tip (for less than 2 seconds) and the Internet Camera will re-boot
itself, keeping your original configurations.
2.
If problems persist or you experience extreme problems or you forgot your
password, press the reset button for longer than 5 seconds and the Internet
Camera will reset itself to the factory default settings (warning: your original
configurations will be replaced with the factory default settings).
Power Jack
LAN Port
Reset Button
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
3
MWIPC-1510WG User Manual
4.3.
Installation Procedure
1. Unpack the Internet Camera package and verify that all the items listed in the Chapter 2
are provided.
2. Connect the Internet Camera to your network by attached the network cable from the
switch/router to the UTP port of the Internet Camera.
3. Connect the power adapter to the Internet Camera and plug the power adapter to power
outlet. The Internet Camera will be powered on. When the Internet Camera is ready, the
Ready LED will light.
4. Make sure that you have installed correct VGA driver and DirectX 9.0 or above.
Note: It is highly recommended to use the power adapter shipped with the Internet Camera,
do NOT use any other power adapter from any sources.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
4
MWIPC-1510WG User Manual
5.
Software Installation
Follow the simple steps below to run the Install Wizard to guide you quickly through the
Installation process. The following installation is implemented in Windows XP. The installation
procedures in Windows 2000/Server 2003 are similar.
1. Insert the CD shipped along with the Internet Camera into your CD-ROM drive. The
“Autorun.exe” program should be executed automatically. If not, run “Autorun.exe”
manually from “Autorun” folder in the CD.
2. The Install Wizard will show four selections, select the program you want to install or click
“Exit” to install the program later. The following installation steps are the demonstration of
“Install Administrator Utility & Camera Viewer”.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
5
MWIPC-1510WG User Manual
3. The system will start the installation procedures. Click “Next” to continue installation.
4. If you wish to install the software program in an alternate location, click “Change”;
otherwise click “Next” to move on to the next step.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
6
MWIPC-1510WG User Manual
5. Click “Install” to start installing the program.
6. The system will install the program automatically.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
7
MWIPC-1510WG User Manual
7. Click “Finish” to complete the software installation.
8. ”Administrator Utility“ will be run automatically after installation. On the Internet Camera
first page, the cameras found in the network are listed in the left window. Choose the one
you want to configure and click “Setting Wizard” to proceed.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
8
MWIPC-1510WG User Manual
9. Please enter the default password “1234” and click “OK” to login to the IP setup page.
10. Internet Camera is working through the network (TCP/IP Protocol). The IP address and
subnet mask setting must be correct, or you cannot access to the camera. The wizard
program will detect the IP address status of your network automatically and suggest a free
IP address for the Camera. You can accept the suggested value or enter the value
manually. If you enter the value manually, please be aware that the “Subnet Mask” must
be the same for both the camera and the PC. Click “Finish” to apply the configuration.
11. This wizard will pop up a window to ask you if you want to run the “Camera Viewer” and
see the video of the Camera immediately. Select “OK” to run “Camera Viewer”.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
9
MWIPC-1510WG User Manual
12. The “Camera Viewer” will show the video automatically. Congratulations, you can use the
camera through the network to view the video from now on.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
10
MWIPC-1510WG User Manual
6.
Using the Administrator Utility
The Administrator Utility allows users to search and setup the cameras located within the
Intranet or on the Internet. From the utility, users can view all the information of the selected
camera; furthermore, it provides a setting wizard, which can guide users to add the camera to
the network easily and promptly.
There are two ways to run the Administrator Utility as follows.
1. Click “Start”, select “Programs\IP Camera\Admin Utility” to run the utility.
2. Double click the “IP Camera Admin” icon
to run the utility.
Once the utility is started, it will search all the cameras within the network. To do more settings,
please refer to the description in the following sections.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
11
MWIPC-1510WG User Manual
6.1.
General Setting
LAN
Auto Discover
Click the button will search the camera within the network.
Camera List
The list shows the camera name and the setup status of the
camera.
It means the camera is in the default setting.
It means the camera is configured before.
Internet
Add
Click “Add” will appear a window for you to enter the IP Address
of the camera on the Internet.
Delete
Click “Delete” to delete the camera from the list.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
12
MWIPC-1510WG User Manual
Camera List
The list shows the camera name and the connect status of the
camera.
It means the camera is disconnected or not in
the Internet.
It means the camera is connected.
Information of Camera
Camera Information
It displays all information of the selected camera. The information
includes Firmware Version, Network Information, IP Address,
UPnP Setting, DDNS Setting, Resolution and E-mail setting, etc.
Camera Setting
Detail Setting
Click “Detail Setting” to do more setting of the camera such as IP
address, Resolution, password and firmware upgrade, etc.
Setting Wizard
Click “Setting Wizard” to setup the necessary setting for the
camera.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
13
MWIPC-1510WG User Manual
6.2.
Detail Setting
When you click the “Detail Setting”, a screen will pop up for you to enter the “Administrator
Name” and “Password”. The default value is as follows.
Name: “Admin”
Password: “1234”
If the name and password you enter are correct, you can start to setup the camera.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
14
MWIPC-1510WG User Manual
6.2.1.
Network Setting
Network Setting
Internet Camera Name
The default camera name is “MWIPC-1510WG”. It is
recommended to name a meaningful name for the camera.
IP Address
Enter an unused IP Address within the IP address range used on
your LAN. If the IP Address of your LAN is from the 192.168.2.1
to 192.168.2.254, you can set an unused IP Address from the
range for the camera, for example: 192.168.2.250.
Subnet Mask
The Subnet Mask field must match the subnet setting on your
LAN. For example: 255.255.255.0.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
15
MWIPC-1510WG User Manual
Gateway
The Gateway is used to forward frames to destinations in a
different subnet on the Internet. The Gateway setting must be the
same with the gateway used by the PCs on your LAN.
DNS Server
DNS Server (Domain Name Server) that translates names to IP
addresses. Set the same DNS Server as the PCs on your LAN.
Network Setting
Video Port
The Video Port is used to transmit or receive the video streaming
in the network. The default port setting is “4321”. If you want to
view the video from the camera, the port setting should be
correct.
Web Port
This camera support web connection, the default web port is 80.
Since the web server may use port 80, you can use a different
port for the camera. If you change the web port from 80 to 8080,
you must type http://192.168.2.3:8080 to connect the camera
through the web browser.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
16
MWIPC-1510WG User Manual
6.2.2.
Wireless Settings (*Wireless Model Only)
Utility will site survey automatically or you can press “Refresh” button to survey the AP router
manually.
After site survey procedure, there will show existing AP SSID.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
17
MWIPC-1510WG User Manual
Then press “Connect” to connect AP router or press “Add to Profile” to configure the Wireless
WEP and WPA encryption.
There are WEP(Open System/Shared Key) ,WPA-PSK,WPA2-PSK and WPANone encryption
settings. You can choose one to match AP router wireless settings.
After set the profile, Please remove the LAN cable then IP Camera will connect to AP router
automatically.
LED Status Diagram
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
18
MWIPC-1510WG User Manual
Wired Setting Environment
Wireless Setting Environment
You must configure the wireless settings from wired environment. Then you can
remove the wired cable and start wireless connection.
6.2.3.
E-Mail Setting
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
19
MWIPC-1510WG User Manual
E-Mail Setting
Recipient E-Mail Address
This camera supports “Snap Shot” and “Motion Detection”
functions. You can snapshot a picture and send the picture by
E-Mail. Enter the E-Mail Account for receiving the picture.
SMTP Server
Enter the SMTP Server for the E-Mail sending.
Sender E-Mail Address
Specified the e-mail address of the e-mail sender.
Authentication
Enable or Disable the SMTP Authentication function
Username
When Authentication is enabled, input the SMTP Username.
Password
When Authentication is enabled, input the password.
Send a Test Email
Press this button to send a test e-mail to your mailbox. You can
use this function to test if your setting is correct.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
20
MWIPC-1510WG User Manual
6.2.4.
PPPoE Settings
PPPoE Settings
Enable/Disable
If enable the PPPoE function, IP Camera will use PPPoE for
network connection first. The default value is “Disable”.
Username
Enter the Username of PPPoE connection.
Password
Enter the Password of PPPoE connection
MTU
A maximum transmission unit (MTU) is the largest size packet or
frame, specified in octets (eight-bit bytes), that can be sent in a
packet or frame based network such as the Internet.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
21
MWIPC-1510WG User Manual
6.2.5.
FTP Settings
FTP Settings
FTP Server
This camera supports “Motion Detection” functions. When Motion
Detection event occurred, you can record the pictures to FTP
server. Enter the FTP address for receiving the pictures.
FTP Port
Enter the port of the FTP server.
User Name
Specify the user account of ftp server.
Password
Specify the Password of your ftp account.
Remote Folder
Specify the folder of the ftp site that you want to store the video.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
22
MWIPC-1510WG User Manual
Passive Mode
If your Camera is under NAT, you usually need to enable this
feature.
6.2.6.
Date / Time Settings
Date / Time Settings
Set Date/Time manually
Set the current Date and Time.
NTP Server
Synchronize the Date and Time with NTP server.
Time Zone
Select the time zone that your camera put on.
NTP Server
Specify the IP Address of the NTP Server.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
23
MWIPC-1510WG User Manual
6.2.7.
Resolution
Resolution
Resolution
Select the desired video resolution format. Larger resolution
requires more bandwidth. 640 x 480 is “VGA” format. 320 x 240 is
“CIF” format. 176 x 144 is “QCIF” format.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
24
MWIPC-1510WG User Manual
6.2.8.
Advanced Setting
Advanced Setting
UPnP
When the UPnP function is enabled, the camera can be detected
by UPnP compliant system such as Windows XP. The camera
will be displayed in the Neighborhood of Windows XP, so you can
directly click the camera to view the video through web browser.
DDNS
Many internet connections use a "Dynamic IP address", where
the Internet IP address is allocated dynamically whenever the
Internet connection is established. Internet users should know the
IP Address of the camera when they want to connect to the
camera every time. DDNS is designed to solve this problem, by
allowing users to connect to your LAN using a domain name,
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
25
MWIPC-1510WG User Manual
rather than an IP address.
Enable/Disable
Enable or disable DDNS function of the camera.
Provider
Several companies provide DDNS service. This camera supports
the service from DynDNS who is one of the DDNS providers.
Domain Name
The domain name given by DynDNS is
“registername.dyndns.com”. Enter the domain name that you
register for the camera from DynDNS web site.
Account
Enter the login name for the DDNS service.
Password
Enter the password for the DDNS service.
6.2.9.
Users
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
26
MWIPC-1510WG User Manual
Users
Administrator
Setting the password of Administrator account
Current Password
Enter the current password of the camera.
New Password
Enter the new password you want to use for the camera.
Confirm New Password
Retype the new password to confirm the setting.
User
Setting the user account and password. Your camera can support
4 user account.
6.2.10.
Tools
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
27
MWIPC-1510WG User Manual
Tools
Firmware Version
Display current firmware version.
Firmware Update
You can upgrade camera’s firmware via this function. Press this
button and select the correct firmware to upgrade.
Reset to Default
If you want to reset the camera, click this button. The default
settings of the camera are as follows.
Camera Name: “MWIPC-XXXXXX”
IP Address: “192.168.2.3”
Subnet Mask: 255.255.255.0
Administrator Name: “Admin”
Password: “1234”
Video Port: “4321”
Web Port: “80”
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
28
MWIPC-1510WG User Manual
6.2.11.
About
About
Administrator Utility
Display current Administrator Utility Version.
Version
6.3.
Setting Wizard
When you click the “Setting Wizard”, a screen will pop up for you to enter the “Administrator
Name” and “Password”. The default value is as follows.
Name: “Admin”
Password: “1234”
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
29
MWIPC-1510WG User Manual
If the name and password you enter are correct, you can start to setup the camera.
Setting Wizard
Internet Camera Name
The default camera name is “MWIPC-1510WG”. It is recommended
to enter a meaningful name for the camera.
IP Address
The wizard will auto setup an available IP Address to the camera.
For example: if the IP address of the network is 192.168.2.x, the
wizard will search an unused IP Address from 192.168.2.1 to
192.168.2.250 and assign the camera an available IP Address.
You are allowed to enter another IP Address to change the setting.
Subnet Mask
The wizard will auto search the Subnet Mask setting of the network
and set the camera in the same Subnet Mask.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
30
MWIPC-1510WG User Manual
You can enter another Subnet Mask to change the setting.
Gateway
The wizard will auto search the Gateway setting of the network and
set the camera to use the same Gateway.
You can enter another Gateway to change the setting.
Video Port
It defines the video stream port. The default value is “4321”.
Cancel
Click “Cancel” to stop wizard setting.
Finish
Click “Finish” to complete the camera setting.
When you finish the camera setting, you can click “Ok” to run the “Camera Viewer”
immediately or click “Cancel” to run the “Camera Viewer” later.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
31
MWIPC-1510WG User Manual
7.
Using the Camera Viewer
The Camera Viewer Utility allows users to view video up to four cameras. It also allows users
to manual/schedule recording video and playback the video file. The status of camera viewing
such as frame rate, video received, and etc. are also recorded in time.
There are three ways to run the Camera Viewer Utility as follows.
1. Click “Start”, select “Programs\IP Camera\Camera Viewer” to run the utility.
2. Double click the “IP Camera Viewer” icon
to run the utility.
3. Click “Setting Wizard” from Administrator Utility and follow the instructions in the utility.
7.1.
Panel Introduction
In the beginning when you start the Camera Viewer, you would see a Control Panel and a four
division Viewer window.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
32
MWIPC-1510WG User Manual
7.2.
Camera Buttons
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
33
MWIPC-1510WG User Manual
Camera Buttons
Click one of these four cameras will connect to the selected
Camera
camera that you want to view and configure. If you want to
remove the camera from the viewer, please right click the icon
and select “Reset Camera x”. If you want to configure the
camera, please right click the icon and select “Configure
Camera x”.
7.3.
Camera Status
There is a status bar shown different color to indicate the status of each Internet Camera.
Camera Status
Yellow
It means that there is no camera set to connect.
Blue
It means that the camera is connected and playing the live video.
Pink
It means that the camera is not connected now.
Red
It means that the camera is recording.
7.4.
Control Buttons
Snapshot
Pause
Close the Camera Viewer
Minimize the Window
Stop
Record
Play
Forward
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
34
MWIPC-1510WG User Manual
Control Buttons
Play
The “Play” button is an intelligent play user-interface. In the
normal display mode and the Internet Camera is disconnected,
clicking on the “Play” can make the viewer connect to the Internet
Camera. In the playback mode, clicking on the “Play” can play the
video in the normal speed.
Stop
The “Stop” button is an intelligent play user-interface. In the
normal display mode and the Internet Camera is connected,
clicking on the “Stop” can make the viewer disconnect the
camera. In the playback mode, clicking on the “Stop” can stop
playing the video.
Pause
The “Pause” button provides you a way to pause the current
video display. When the displaying video is paused, click on the
“Play” again to resume the video display.
Forward
The “Forward” button to forward the speed of display when
playback the recording file. Click the button at a time will increase
the playing speed one time.
Snapshot
Click “Snapshot” will make the viewer to take a snapshot of the
video and save the picture as a bitmap file in the hard disk. (You
can set the directory for storing these bitmap files at the Section
7.8.4)
Record
By clicking “Record” you can record video immediately. (You can
set the directory for storing video files at the section 7.8.4)
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
35
MWIPC-1510WG User Manual
7.5.
Video Recording
This utility allows you record the video in AVI files. There are two ways of video recording –
Manual Recording and Schedule Recording.
Manual Recording
You can manually record the video stream into an assigned video file.
Click “Record”, then the viewer utility will start to record the video stream. You can assign the
path in the setting dialog.(at section 7.8.4)
Clicking “Stop” will stop recording.
Note: Before manual recording, you have to click the camera button to select the Internet
Camera that you want to record first and make sure that the viewer is successfully connecting
to the Internet Camera.
Schedule Recording
You can assign a schedule and let this viewer automatically recording the video stream.
Please refer to Section 7.8 to see how to setup schedule for the recording. The file name of
the recorded video file is the start time of recording. For example, the file name
“IPCamera_2004-10-8-23-56-40.avi” means it was recorded at 2004/10/8 23:56:40.
7.6.
Change Resolution
The Internet Camera supports two resolution, 640x480 (VGA) and 320x240 (CIF). You can
change the resolution of each Internet Camera by clicking the resolution button.
Note: Before changing the resolution of the Internet Camera, you have to select the Internet
Camera by clicking the camera button first. If you change the resolution of an Internet Camera,
other clients who are viewing the same Internet Camera simultaneously will also see the video
with the changed resolution, too.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
36
MWIPC-1510WG User Manual
Resolution
VGA
Change the resolution to 640x480 (VGA) mode.
QVGA
Change the resolution to 320x240 (QVGA) mode.
7.7.
View Four Cameras Simultaneously
Click the four division button
can view the 4 cameras simultaneously in a four-division
window.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
37
MWIPC-1510WG User Manual
7.8.
Viewer Utility Setting
Click the “Setting” button
, then the setting window of the Internet Camera will pop up.
Note: When you want to change the settings such as IP Address, Video Port, etc. in the
“Setting” option, you must disconnect the Internet Camera first by clicking the “Stop”.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
38
MWIPC-1510WG User Manual
7.8.1.
Setting
Setting
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
39
MWIPC-1510WG User Manual
Name
It is not required to fill the camera name for connecting camera. It
is for users to identify the camera.
IP Address
IP address/Domain name of the Internet Camera.
Video Port
The number of service port used by the Internet Camera.
Model
Select “Internet Camera” (This camera only supports MJPEG).
Username
The user name for login into the Internet Camera. By default, the
user name is “Admin”.
Password
The password for login into the Internet Camera. By default, the
password is “1234”.
Discover
Click “Discover”, then camera auto-discover windows will pop up.
The window will show all the discovered cameras on LAN
environment for you to select.
7.8.2.
Recording
You can setup schedule for the recording here. This utility will record the video stream in the
assigned file folder according to the schedule automatically. The recorded video files are AVI
format.
Note:
1. The utility will only start to record the video stream when this utility is running and is
successfully connecting to the Internet camera in the beginning of the schedule.
2. The schedule setting of one-time or weekly schedule should not overlap, or the recording
will fail.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
40
MWIPC-1510WG User Manual
One-Time Schedule
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
41
MWIPC-1510WG User Manual
Weekly Schedule
Schedule
Cycle Recording
Check this check box to enable cycle recording. When the Cycle
Recording is checked and the storage usage has already
reached the maximum reserved storage space, the utility will
automatically delete the oldest recorded video file and use the
space to store the newly recorded video stream.
One-Time Schedule
You can assign a range of time and the utility will automatically
record the video stream only during the period of time. The
default time is 2 minutes later from the current time.
Weekly Schedule
You can assign the days in a week and the period of time in a day
when you want to record the video stream. The utility will
automatically record the video stream during the periods of time
every week again and again.
Schedule
New
Click “New” to add a new recording schedule.
Edit
Select an existing schedule in the schedule list and click “Edit” to
edit the schedule.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
42
MWIPC-1510WG User Manual
Delete
Select an existing schedule in the schedule list and click “Delete”
to delete the schedule.
7.8.3.
Status
You can see the current status information of the connection session between the utility and
the Internet Camera.
Status
Connected
It displays “Yes” when the utility is connecting to the Internet
Camera and displays “No” when the utility is not connecting to the
Internet Camera.
Status
Stream Started At
The beginning time of the current connection session between
the utility and the Internet Camera.
Time Elapsed
The elapsed time of the current connection session between the
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
43
MWIPC-1510WG User Manual
utility and the Internet Camera.
Video Received
The total size (Unit is KByte) of video stream received during the
current connection session between the utility and the Internet
Camera.
Audio Received
The total size (Unit is KByte) of audio stream received during the
current connection session between the utility and the Internet
Camera. (Reserved)
Frame Rate
The frame rate (frame per second) of the current video download
speed from the Internet Camera to the utility.
Data Rate
The data rate (KByte per second) of the current video download
speed from the Internet Camera to the utility.
Number of Frames
The total number of video frames received during the current
connection session between the utility and the Internet Camera.
Number of Users
7.8.4.
The total number of users that viewing this camera currently.
General
You can manage storage usage for this Internet Camera here.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
44
MWIPC-1510WG User Manual
General
Snap Shot Directory
This lets you assign the directory where bitmap files will be stored
when you click “Snapshot” to take pictures. The default folder is
where the software program is installed, for example:
“C:\Program Files\Internet Camera”.
Record Directory
This lets you assign the directory where the recorded video files
will be stored. The default folder is where the software program is
installed, for example: “C:\Program Files\Internet Camera”.
Free Disk Space
The current free disk space of the hard drive where is assigned to
save recording files.
Max Recording Space
You can reserve a disk space to store the recorded video and
snapshot files. If the space is run out, a message will pop up to
remind you.
Used Disk Space
The current used disk space for saving the recording file.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
45
MWIPC-1510WG User Manual
Max Video File Size
This let you assign a maximum size of each video file. The upper
bound of this value is 2 GB per file.
7.8.5.
About
About
Camera Viewer Utility
Display current Camera Viewer Utility Version.
Version
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
46
MWIPC-1510WG User Manual
7.9.
Playback
Click the “Open File” and a “Load File” window will be popped up. Select the file that you want
to play.
The viewer will start to play the selected video file.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
47
MWIPC-1510WG User Manual
Playing Control
Play
When the video playback is in Stop state, just click “Play” and the
viewer will play the video file from the beginning point. When the
video playback is in Pause state, just click “Play” and the viewer
will play the video file from the current pause point. When the
viewer is playing with fast speed, just click “Play” to let the viewer
play with the normal speed.
Pause
When the recorded video is playing, you can click “Pause” to
freeze the playback. If you want the viewer to continue playing
from the current pause point, just click “Play”.
Stop
When the viewer is playing, you can click “Stop” to stop the
playback. If you want the viewer to play again, just click “Play”
and the viewer will play the video file from the beginning point.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
48
MWIPC-1510WG User Manual
Playing Control
If you want the viewer to play the video file in a faster speed when
Forward
the viewer is playing the video file, just click “Forward” and the
viewer will double the playing speed. If you want the viewer play
with the normal speed when the viewer is playing with fast speed,
just click “Play”.
7.10.
Rotate Video
Rotate function lets you rotate the video frame 180 of degree angle each time you click the
“Rotate”
. With this function, you can view the live video with normal, and 180 degree
angles counterclockwise.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
49
MWIPC-1510WG User Manual
8.
Web Connection and Setup
You can use the Web browser to connect the camera for viewing or setting. Open the web
browser and enter the IP Address of the camera to establish a connection. The default IP
Address of the camera is “192.168.2.3”.
When the welcome screen appears, enter the “Admin Name” and “Password”. The default
values are:
Admin Name: “admin”
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
50
MWIPC-1510WG User Manual
Password: “1234”
When the camera is connected, the browser will take you to the live video page. If you are viewing this
camera at first time, the following dialog will appear to install the ActiveX plug in. Please check the
publisher part, you should only accept it if it is published by EPCT Corporation
After installed the ActiveX plug-in, the video image will be shown up in the web screen directly.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
51
MWIPC-1510WG User Manual
The menu options for the web control screen are as follows.
Camera – View live video and adjust the video format from the menu.
LAN – Setup the camera LAN port functions in the menu.
WLAN – Setup the camera WLAN port functions in the menu.
E-Mail & FTP – Setup the E-Mail client and FTP client in the menu.
Motion Detection – Configure the Motion Detection Actions here.
System – Setup System utilities and settings in this menu.
Status – Shows the camera information and current status in this page.
Users – This camera support up to 4 user accounts. You can setup them in this menu.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
52
MWIPC-1510WG User Manual
8.1.
Camera Setting
Camera Setting
Resolution
Select the desired video resolution format. Larger resolution
requires more bandwidth. 640 x 480 is “VGA” format. 320 x 240 is
“CIF” format. The default resolution is CIF format.
Image Quality
Adjust this property to control the video quality
Max Frame Rate
Set the video max frame rate. This camera can support at most
30 frames per second. Set the frame rate higher can get video
more smooth. But will use more bandwidth.
Frequency
Adjust this property to fitting light frequency.
Brightness
You can adjust the brightness of the video. If the video is too dark,
you can input the larger number in this text box. The video will be
brighter. This value can be from 1 to 100.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
53
MWIPC-1510WG User Manual
Contrast
You can adjust the contrast by change the value. This value can
be from 1 to 100.
Saturation
You can adjust the saturation by change the value. This value can
be from 1 to 100.
Hue
You can adjust the hue by change the value. This value can be
from 1 to 100.
Whiteness
You can adjust the white balance by change this value.
This
value can be from 10 to 30.
Enable Auto Exposure
You can enable Auto Exposure by check this box.
Enable OSD
You can enable or disable “Time Stamp” function in this item.
When you disable “OSD” function, the “Time Stamp” will be
hidden.
Apply
When you finish “AV Server” setting, click this button to validate
the setting values.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
54
MWIPC-1510WG User Manual
8.2.
LAN Setting
LAN
Network Type
This camera can obtain IP via DHCP protocol or specified static
IP Address to it..
IP Address
Enter an unused IP Address within the IP address range used on
your LAN. If the IP Address of your LAN is from the 192.168.2.0
to 192.168.2.250, you can set an unused IP Address from the
range for the camera, for example: 192.168.2.250.
Subnet Mask
The Subnet Mask field must match the subnet setting on your
LAN. For example: 255.255.255.0.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
55
MWIPC-1510WG User Manual
Gateway
The Gateway is used to forward frames to destinations in a
different subnet on the Internet. The Gateway setting must be the
same with the gateway used by the PCs on your LAN.
DNS Server
DNS Server (Domain Name Server) that translates names to IP
addresses. Set the same DNS Server as the PCs on your LAN.
Video Port
The AV Control Port is used to transmit or receive the AV
streaming in the network. The default port setting is “4321”. If you
want to view the video from the camera, the port setting should
be correct.
Web Port
This camera support web connection, the default web port is 80.
Since the web server may use port 80, you can use a different
port for the camera. If you change the web port from 80 to 8080,
you must type http://192.168.2.3:8080 to connect the camera
through the web browser.
Apply
When you finish the “LAN”, click “Apply”.
PPPoE
Enable PPPoE
Enable or disable PPPoE function of the camera.
User Name
Enter the User Name for the PPPoE Connection.
Password
Enter the Password for the PPPoE Connection.
MTU
A maximum transmission unit (MTU) is the largest size packet or
frame, specified in octets (eight-bit bytes), that can be sent in a
packet or frame based network such as the Internet.
Apply
When you finish the “PPPoE” setting, click “Apply”.
Dynamic DNS
Enable DDNS
Enable or disable DDNS function of the camera.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
56
MWIPC-1510WG User Manual
Provider
Several companies provide DDNS service. This camera supports
the service from DynDNS company.
Domain Name
The domain name given by DynDNS is
“registername.dyndns.com”. Enter the domain name that you
register for the camera from DynDNS web site.
User Name
Enter the login name for the DDNS service.
Password
Enter the password for the DDNS service.
Apply
When you finish the “Dynamic DNS” setting, click “Apply”.
UPnP
Enable UPNP
Enable or disable UPnP function of the camera.
Apply
When you finish the “UPnP” setting, click “Apply”.
LoginFree
Filename
The default value is “loginfree”. That’s mean user can get a snapshot
image from Internet Explorer. The format is like:
IP Camera will send a snapshot image to Internet Explorer.
If user changed file name (Ex: “1234”), the URL must be changed to
“http://192.168.2.3/1234.jpg”
Apply
When you finish the “UPnP” setting, click “Apply”.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
57
MWIPC-1510WG User Manual
8.3.
WLAN
Wireless Setting
Wireless connection
Enable or disable the wireless function of the Internet Camera. By
default, the function is disabled.
Network Type
Infrastructure – This operation mode requires the presence of a
Wireless LAN Access Point or Router. All communication is done
via the Access Point or Router.
Ad-Hoc – Select this mode if you want to connect to another
wireless stations in the Wireless LAN network without through an
Access Point or Router.
Available Networks
Select the networks listed below and click apply to connect to the
specified network.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
58
MWIPC-1510WG User Manual
SSID
The SSID (up to 32 printable ASCII characters) is the unique
name identified in a WLAN. The ID prevents the unintentional
merging of two co-located WLANs.
You may specify a SSID for the card and then only the device
with the same SSID can interconnect to the card. If you want to
add one of the networks nearby to the profile list, pull down the
menu, all the networks nearby will be listed and you can add one
of them to the profile list.
Channel
This setting is only available for Ad Hoc mode. Select the number
of the radio channel used for the networking. The channel setting
should be the same with the network you are connecting to.
Basic Rate
The camera will force to the data rate that you selected to
transmit data.
Authentication and
Choose the authentication type you want to use.
Encryption Type
“None” means that you don’t want any encryption for wireless.
“Open System” means that you can use WEP for encryption or
not to encryption. When you select “Shared Key”, you must use
WEP for encryption. The last option is “WPA-PSK”. When you
select this authentication type, you can encryption your wireless
with WPA-TKIP or WPA-AES.
WPA Pre-Shared Key
The WPA-PSK key can be from 8 to 64 characters and can be
letters or numbers. This same key must be used on all of the
wireless stations in the network.
WEP Key Length
You may select 64-bit or 128-bit to encrypt transmitted data.
Larger key length will provide higher level of security, but the
throughput will be lower.
WEP Key Format
Hexdecimal – Only “A-F“, “a-f“ and “0-9“ are allowed to be set as
WEP key.
ASCII – Numerical values, characters or signs are allowed to be
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
59
MWIPC-1510WG User Manual
WEP key. It is more recognizable for user.
Default Key
Select one of the keys (1~4) as the encryption key.
Key1 ~ Key4
The WEP keys are used to encrypt data transmitted in the
wireless network.
Fill the text box by following rules below.
64-bit – Input 10-digit Hex values (in the “A-F”, “a-f” and “0-9”
range) or 5-digit ASCII characters (including “a-z” and “0-9”) as
the encryption keys. For example: “0123456aef“ or “test1”.
128-bit – Input 26-digit Hex values (in the “A-F”, “a-f” and “0-9”
range) or 13-digit ASCII characters (including “a-z” and “0-9”) as
the encryption keys. For example:
“01234567890123456789abcdef“ or “administrator”.
Apply
When you finish “WLAN” setting, click this button to validate the
setting values.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
60
MWIPC-1510WG User Manual
8.4.
E-Mail and FTP
The “E-Mail & FTP” lets you setup E-Mail client and FTP client that camera can sent live video
to your e-mail account or FTP server when Motion has been detected.
AV Server
Recipient E-Mail Address
This camera supports “Motion Detection” function. Enter the
E-Mail Account for receiving the pictures.
SMTP Server
Enter the SMTP Server for the E-Mail sending.
Sender E-Mail Address
Specified the e-mail address of the e-mail sender.
SMTP Authentication
Enable or Disable the SMTP Authentication function
Username
When Authentication is enabled, input the SMTP Username.
Password
When Authentication is enabled, input the password.
Send a Test Email
Press this button to send a test e-mail to your mailbox. You can
use this function to test if your setting is correct.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
61
MWIPC-1510WG User Manual
FTP Server
This camera supports “Motion Detection” functions. When Motion
Detection event occurred, you can record the pictures to FTP
server. Enter the FTP address for receiving the pictures.
FTP Port
Enter the port of the FTP server.
User Name
Specify the user account of ftp server.
Password
Specify the Password of your ftp account.
Remote Folder
Specify the folder of the ftp site that you want to store the video.
Password
When Authentication is enabled, input the password.
Passive Mode
If your Camera is under NAT, you usually need to enable this
feature.
8.5.
Motion Detection
The “Motion Detection” allows users to setup the behavior of motion detection feature.
Motion Detection
Motion Detection Enable
Enable or Disable the Motion Detection Function.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
62
MWIPC-1510WG User Manual
Next Event Detected
Setup the interval between two events. For example, if you setup
Interval
the interval to 5 seconds, the next event will start after this event
finished + 5 seconds.
Threshold
Setup the sensitivity of motion detection.
Send Recording File to
Select Yes to send the recorded video file to your e-mail account
E-Mail
that you had specified at “E-Mail & FTP” menu.
E-Mail Subject
Specify the subject of motion detection notify e-mail.
Send Recording File to
Select Yes to send the recorded video file to your FTP server that
FTP
you had specified at “E-Mail & FTP” menu.
8.6.
System
The “System” allows users to setup the camera’s parameters, like camera name, data/time
setting. And also provide firmware upgrade and reset tools at this page.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
63
MWIPC-1510WG User Manual
System
Camera Name
The default camera name is “MWIPC-1510WG”. It is
recommended to name a meaningful name for the camera.
Login Name
Setup your administrator account’s login name. Default name is
“admin”
Password
Enter up to 4 digits password for the new user account.
Confirm Password
Enter the password again to confirm the setting.
Set Date/Time manually
Display the current Date and Time.
NTP Server
Synchronize the Date and Time with this NTP server.
Time Zone
Select the time zone that your camera put on.
NTP Server
Specify the IP Address of the NTP Server.
Upgrade Firmware
You can upgrade camera’s firmware via this function. Press the
browse button, find the correct firmware and press upgrade.
Reset to Factory Defaults
If you want to reset all the camera settings to default, click this
button.
Reboot Device
To reboot the Internet Camera, click “Reboot”.
LED Setting
There are four LEDs to indicate the status of Internet Camera. If
you wan to secure the camera from noticing, you can turn off the
LED light by clicking “LED Light OFF”. To turn on the LED light,
click “LED Light ON”.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
64
MWIPC-1510WG User Manual
8.7.
Status
The “Status” shows the current firmware version, uptime, system time and IP information of
this camera.
8.8.
Users
The “Users” allows users to add four user accounts which are able to view video from Camera
Viewer and Web Management. These users, unlike Administrator, are not allowed to
configure the camera.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
65
MWIPC-1510WG User Manual
User 1 / 2 / 3 / 4
User #
Enable or Disable the user number #.
Login
Enter the the login name to the camera.
Password
Enter up to 4 digits password for the new user account.
Confirm Password
Enter the password again to confirm the setting.
Apply
Click “Apply” to save the user account setting.
8.9.
Log
The “Log” allows users to monitor the device event and time. If you have trouble to use this
device, the log file will help administrator to know the status of device.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
66
MWIPC-1510WG User Manual
Log
Log screen
The screen will show event and event time of device.
Refresh
You can press “Refresh” button to refresh the log screen.
Frequently Asked Questions
Q1: What is an Internet Camera?
A: The Internet Camera is a standalone system connecting directly to an Ethernet or Fast Ethernet
network. It is different from the conventional PC Camera; the Internet Camera is an all-in-one system
with built-in CPU and web-based solutions providing a low cost solution that can transmit high quality
video images for monitoring. The Internet Camera can be managed remotely, accessed and controlled
from any PC/Notebook over the Intranet via a web browser or camera viewer.
Q2: What algorithm is used to compress the digital image?
A: The Internet Camera utilizes MJPEG video compression technology to provide high quality images.
MJPEG is a standard for video compression and can be applied to various application software.
Q3: Can I capture or record still images from the Internet Camera?
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
67
MWIPC-1510WG User Manual
A: Yes, you are able to capture or record still images with the snapshot function from the Camera
Viewer application supplied with the Internet Camera CD-ROM.
Q4: What network cabling is required for the Internet Camera?
A: The Internet Camera uses Category 5 UTP Twisted-pair cable allowing 10 Base-T and 100 Base-T
networking.
Q5: Can the Internet Camera be setup as a PC-cam on the computer?
A: No, the Internet Camera is used only on Ethernet and Fast Ethernet network.
Q6: Can the Internet Camera be connected on the network if it consists of only private IP
Addresses?
A: Yes, the Internet Camera can be connected to a LAN with private IP Addresses.
Q7: The focus on the Internet Camera is bad, how can I correct it?
A: Adjust the Internet Camera focus manually.
9.
„
Technical Specifications
Video specification
Max Resolution: 640 x 480 pixels
Sensor: 300K pixels 1/4" color CMOS sensor
Gain control: Automatic
Exposure: Automatic
White Balance: Automatic
Focal Length: 4.8 mm
Aperture: F=1.8
„
Image (Video Setting)
Image compression: MJPEG Image Video
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
68
MWIPC-1510WG User Manual
Digital 24-bit Color
Frame rate: 30fps@QVGA, 20fps@VGA
Video resolution: 176 x 144, 320x240, 640x480
„
System Hardware
LAN Connector: One RJ-45 port to connect to 10/100Mbps Ethernet
Wireless: IEEE 802.11b/g(*Wireless Model Only)
LED Indicator: LAN LED (Green), WLAN LED (Amber), Power LED (Blue)
Power Supply: 12V / 1A (Wireless Model)
Power Supply: 12V / 0.4A (Wired Model)
„
HTTP/Utility
Includes easy-to-use Viewer & Recorder utility
Provides Admin utility & WEB browser Management
View multiple cameras simultaneously - Up to 4 cameras at a time
Manual/Schedule Record, Video Playback/Stop/Forward/Pause
Supports four additional user accounts for viewing camera
Auto sending Snap Shot by E-mail or FTP
Support DDNS and UPnP functions
Supports Windows 2000/XP/2003
Firmware Upgradeable
„
EMI & Safety
FCC, CE!
10.
Appendix A Router/Gateway Setup for Internet
Viewing
To view Internet Camera across the Internet, you have to make sure Router/Gateway has
configured to pass incoming TCP/UDP connections from remote PC to the Internet Camera.
The Router/Gateway should set port forwarding or virtual server for the connections. Please
see the illustration as below.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
69
MWIPC-1510WG User Manual
Router/Gateway Port Forwarding/Virtual Server Setup
Name
Protocol
Port
LAN IP
Setup 1
TCP
80
192.168.2.3
Setup 2
TCP
4321
192.168.2.3
Port Definition
Setup 1
It is the port of Web port. You have to configure the protocol to
“TCP”.
Setup 2
It is the port of Video port. You have to configure the protocol to
“TCP”.
Setup 3
It is the port for Internet Camera and Administrator Utility
communication. The protocol setting should be “UDP”.
Viewing Internet Camera via Web Browser
Setup 1/Setup 2
If you want to view the video via Web Browser, you have to
ensure the Router/Gateway has configured setup1 and setup 2. If
the web port is not default port “80”, but changed to 8080. The
remote user has to enter http://203.30.212.82:8080.
Viewing Internet Camera via Camera Viewer Utility
Setup 2
If you want to use Camera Viewer Utility to view the camera,
please make sure the Router/Gateway has configured setup2.
Setup Internet Camera via Administrator Utility
Setup 3
If you want to use Administrator Utility to configure the Internet
Camera via Internet, the Router/Gateway should configure setup.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
70
MWIPC-1510WG User Manual
11.
Appendix B Set up WLAN step by step
Please follow the procedures below:
(1)
Please Check you Router Wireless settings, Suggesting Open System ( Disable
security ) first.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
71
MWIPC-1510WG User Manual
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
72
MWIPC-1510WG User Manual
(2)
Please turn on DHCP Server of the Router for this testing.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
73
MWIPC-1510WG User Manual
(3)
Please reset the Wireless IP Camera settings to Factory Defaults by press the Reset
button over 8 seconds.
(4)
Please change your PC’s IP address to 192.168.2.xx (which xx from 10 to 253),
Netmask = 255.255.255.0
(5)
Please go to Web-Config WLAN section of the Wireless IP Camera.
Press Refresh button until you find the SSID you want in the list first!
Then select the Connect column of the SSID you want and select the Enable button of
Wireless Connection.Press Apply button.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
74
MWIPC-1510WG User Manual
(6)
Please go to the LAN section of Web-Config.Select DHCP and press Apply button.
Then you could close this IE browser window now.
(7)
Please UNPLUG the Ethernet Cable of the Wireless IP Camera now!
(8)
Wait for seconds then the Wireless IP Camera should be linked with the Wireless
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
75
MWIPC-1510WG User Manual
Router.
(9)
Now you could let your PC to be connected with the Wireless Router.
(10)
In this case, if your PC’s DHCP Client IP is 192.168.8.101, then the Wireless IP Camera
must be 192.168.8.100, because Wireless IP Camera was got IP early then your PC.
(11)
You could go to the Web-Interface of the Wireless IP Camera.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
76
MWIPC-1510WG User Manual
12.
Appendix C Viewing via UPnP in Windows XP
When the UPnP function is enabled, the camera can be detected by UPnP compliant system
such as Windows XP. The camera will be displayed in the Neighborhood of Windows XP, so
you can directly double click the camera or right click the camera and select “Invoke” to view
the video through web browser.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
77
MWIPC-1510WG User Manual
Enable UPnP in Windows XP SP2
If you can’t find the camera in the Neighborhood of Windows XP SP2 or you have seen the
following message when you double click the camera. You have to check if UPnP function is
blocked by the firewall. Please follow the steps below to enable it.
1. Go to “Start\Settings\Network Connections”.
2. Right click the “Local Area Connection” and select “Properties”.
3. In the “Local Area Connection Properties”, select “Advanced” option menu and click
“Settings”.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
78
MWIPC-1510WG User Manual
4. The “Windows Firewall” screen will be popped up, select “Exceptions” option menu.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
79
MWIPC-1510WG User Manual
5. Enable “UPnP Framework” from the “Programs and Services list” and click “Ok”.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
80
MWIPC-1510WG User Manual
13.
Appendix D Configure Windows 2003 Server
Graphics Hardware Acceleration and DirectX are disabled by default on a Server
configuration to ensure maximum stability and uptime. But for any reason you need to enable
them to use DirectX enabled applications this section will guide you through on how you can
do it.
Enabling Graphics Hardware Acceleration
1.
Simply right click anywhere on your desktop and select Properties -> Settings tab ->
Advanced -> and finally, the Troubleshoot tab.
2.
Now move the Hardware acceleration slider across to Full
3.
Click OK
4.
You may experience a monitor black out for a few seconds, this is normal.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
81
MWIPC-1510WG User Manual
Enabling DirectX
5.
go to Start -> Run -> and type dxdiag followed by enter. You will get a dialog box asking
if you want to allow dxdiag to access the internet to check for valid WHQL certificates click on Yes.
6.
Let's click on the Display tab, now click on all three boxes to enable DirectDraw, Direct3D
and AGP Texture Acceleration.
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
82
MWIPC-1510WG User Manual
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
83
MWIPC-1510WG User Manual
Internet Camera
MWIPC-1510WG User Manual Copyright © 2006/2007 Minitar Corporation
84
Download PDF