PHL - Instruction Manual (TN2PHLd-E)

PHL - Instruction Manual (TN2PHLd-E)
Instruction Manual
PAPERLESS RECORDER
TYPE: PHL
INP-TN2PHLd-E
PREFACE
Thank you for your purchasing Fuji Paperless Recorder (Type: PHL).
• Read this instruction manual carefully to ensure correct installation, operation and preparation.
Incorrect handling may lead to accident or injury.
• Specifications of this unit are subject to change without prior notice for improvement.
• Modification of this unit without permission is strictly prohibited.
Fuji will not be bear any responsibility for a trouble caused by such a modification.
• This instruction manual should be kept by the person who is actually using the unit.
• After reading the manual, be sure to keep it at a place easy to access.
• This instruction manual should be delivered to the end user without fail.
Manufacturer
: Fuji Electric Co., Ltd.
Type
: Shown on nameplate of Paperless Recorder
Date of manufacture : Shown on nameplate of Paperless Recorder
Product nationality
: Japan
(Note)
Windows 2000/XP/7, Excel, WORD PAD are registered trademarks of Microsoft Corporation.
(Note)
Compact Flash is a trademark of Sandisk Corporation.
© Fuji Electric Co., Ltd. 2005
Request
Issued in December, 2005
• It is prohibited to transfer part or all of the manual without
Fuji’s permission.
Rev. 1st edition January, 2007
• Description in this manual will be changed without prior
notice.
Rev. 3rd edition April, 2011
INP-TN2PHL-E
i
Rev. 2nd edition January, 2008
Rev. 4th edition February, 2012
CAUTION ON SAFETY
Read this “Caution on Safety” carefully before using the instrument.
• Be sure to observe the instructions shown below, because they describe important information on safety.
The degree of danger is classified into the following two levels: “DANGER” and “CAUTION.”
The signs and their meanings are as follows:
DANGER
Improper handling may cause dangerous situations that may
result in death or severe injury.
CAUTION
Improper handling may cause dangerous situations that may
result in moderate or light injuries or property damage.
DANGER
• When there is a possibility that the abnormality of this instrument may cause a major accident or
damage to other instruments, externally install an adequate emergency stop circuit or a protection
circuit to prevent accidents.
• This product is provided with a built-in fuse that cannot be replaced by the customer. Therefore, we
recommend you to separately provide adequate fuses externally. (Rating: 250V, 1A)
The details of the built-in fuse are as follows.
Type: TR-5 19372, 3.15A (Manufactured by Wickmann-Werke GmbH)
Rating: 250V, 3.25A, Type: T (Slow-blow type)
• Feed the power-supply voltage to specifications to prevent damages to and breakdown of the instrument.
• Never turn on the power before all the mounting and wiring work are finished to prevent electric
shock, malfunction or failure of the instrument.
• Never use this instrument in an environment where flammable or explosive gases exist, since this is
not of intrinsically safe construction.
• Never disassemble, remodel, modify, or repair this instrument. Otherwise malfunction, electric
shock, or failure may result.
• Never touch the terminal while the instrument is being energized. Otherwise electric shock or
malfunction may result.
• Turn off the power before attaching/detaching the module/unit. Otherwise electric shock, malfunction or failure may result.
• We recommend you to perform periodic maintenance for the safe and continuous use of this instrument, because consumable parts or those which deteriorate with time are mounted in this instrument.
• Do not block the ventilation holes at the top and the bottom of this instrument. Otherwise a failure,
malfunction, shortened service life, or fire may result.
ii
INP-TN2PHL-E
CAUTION
• Never use the instrument if it is found damaged or deformed when unpacked. Otherwise a fire, malfunction, or failure may result.
• Check that the instrument is to the proper specifications. Otherwise damage or failure may result.
• Do not give a shock to the instrument by falling or toppling it. Otherwise damage or failure may result.
• Operate the instrument paying attention to prevent foreign matters such as scraps, electric wire chips,
and iron powder from entering in the instrument.
• Check every six months that the terminal screws and mounting screws are securely fastened. Loose
screws may cause fire or malfunction.
• When changing the setting during the operation or forcibly outputting, starting or stopping the instrument, be sure to check that safety is ensured. Improper operation may result in damage or failure of the
instrument.
• Be sure to keep the attached terminal cover mounted on the terminal block during the operation. Otherwise electric shock or fire may result.
• Never install this instrument in the following environments.
A place where the ambient temperature goes beyond the range from 0 to 50°C (0 to 40°C when the
instrument is mounted with its side face closely contacted, and in the case of portable type)
A place where the ambient humidity goes beyond the range from 20 to 80% RH
A place where condensation occurs
A place where corrosive gases (sulfuric gases or ammonia, etc., in particular) or flammable gases
exist
A place where vibration or impact may be applied to the instrument (permissible continuous vibration condition: 4.9 m/s2 or lower)
A place subjected to water, oil, chemicals, vapor, or steam
A place subjected to dust and high in salt or iron content
A place where inductive interference may have a great effect, thus causing static electricity, magnetism, or noises
A place subjected to heat accumulation by radiant heat or the like
If the instrument is installed near other electronics instruments, such as TV in particular, noises may
be caused. Take the following measures in these cases.
• Place the instrument as far from the TV or the radio as possible (1m or more)
• Change the orientation of the antenna of the TV or the radio.
• Use separate receptacles.
• When mounting this instrument against the panel, pay attention not to apply stress to the case. Otherwise the case may be damaged.
• Stop using the instrument if it is immersed in water. Otherwise electric leak, electric shock, or fire may
result.
• Do not use the wires other than the specified compensation conducting wires for the thermocouple
input connection. Otherwise improper indication or malfunction may result.
• Use a wire material with low wire resistance and with small resistance difference among the three
wires for the resistance bulb input connection. Otherwise improper indication or malfunction may
result.
INP-TN2PHL-E
iii
CAUTION
• If a large noise is generated from the power supply, provide an isolating transformer and use a noise
filter.
• Never use organic solvents such as alcohol or benzene when cleaning this instrument. Do not directly
water the main unit. Otherwise deterioration, failure, electric leak, electric shock, or fire may result.
When cleaning the main unit, wipe with a dry cloth.
• Dispose the instrument as an industrial waste.
• Be sure to ground the instrument. Otherwise electric shock or malfunction may result.
• Only authorized workers should perform wiring. Improper wiring may cause fire, failure, or electric
shock.
• At this equipment, the electrostatic discharge is evaluated as performance criteria B in EN61326.
iv
INP-TN2PHL-E
CONTENTS
PREFACE .....................................................................................................................i
CAUTION ON SAFETY ............................................................................................ ii
CONTENTS ................................................................................................................. v
1.
2.
3.
4.
5.
INTRODUCTION ............................................................................................ 1-1
1.1
Paperless recorder ............................................................................................... 1-1
1.2
Product check...................................................................................................... 1-1
1.3
Check on type and specification ......................................................................... 1-2
1.4
Handling memory card (Compact Flash) – Cautions on handling ..................... 1-2
NAMES AND FUNCTIONS OF PARTS ....................................................... 2-1
2.1
Names and functions of parts ............................................................................. 2-1
2.2
Inserting and removing the memory card ........................................................... 2-3
2.3
Recording data to memory card .......................................................................... 2-4
MOUNTING METHOD .................................................................................. 3-1
3.1
Mounting location ............................................................................................... 3-1
3.2
External dimensions and panel cutout dimensions (unit: mm) ........................... 3-1
3.3
How to mount the unit onto the panel ................................................................ 3-2
WIRING ........................................................................................................... 4-1
4.1
Before wiring ...................................................................................................... 4-1
4.2
Connection to terminals ...................................................................................... 4-2
4.3
Connecting recorder to loader .......................................................................... 4-12
PORTABLE ..................................................................................................... 5-1
5.1
Portable ............................................................................................................... 5-1
5.2
Handling ............................................................................................................. 5-1
5.3
Outside dimension (unit: mm) ............................................................................ 5-2
5.4
External connection diagram .............................................................................. 5-2
6. DISPLAY FUNCTION ....................................................................................... 6-1
6.1
Basic composition of Data Display screen ......................................................... 6-1
6.2
Real time trend display of measured data ........................................................... 6-3
6.3
Display of measured data in bar graphs or analog meters .................................. 6-5
6.4
Digital display of measured data ........................................................................ 6-6
6.5
Totalizing data display ........................................................................................ 6-6
6.6
Event summary display....................................................................................... 6-8
6.7
Ethernet log display ............................................................................................ 6-9
6.8
Historical trend display ..................................................................................... 6-10
CAUTION
INP-TN2PHL-E
Refer to chapters 3 and 4 only when installing this instrument. Only
qualified workers should carry out mounting and wiring of this instrument.
v
6.9
Display on the occurrence of main unit failure ................................................ 6-11
6.10 Cautions about power ON/OFF ........................................................................ 6-12
7.
8.
9.
OPERATION AND ACTIONS........................................................................ 7-1
7.1
Before running the recorder ................................................................................ 7-1
7.2
Power ON and state ............................................................................................ 7-2
7.3
Stopping and starting the recording operation .................................................... 7-3
7.4
Switching data display screens ........................................................................... 7-5
7.5
Display of alarm ................................................................................................. 7-6
SETTING AND CHECKING PARAMETERS ............................................... 8-1
8.1
Setting and checking ........................................................................................... 8-1
8.2
Outline of parameter setting procedure .............................................................. 8-6
8.3
Basic operation of setting screens..................................................................... 8-10
SETTING PARAMETERS .............................................................................. 9-1
9.1
Basic setting ........................................................................................................ 9-1
9.2
Channel setting ................................................................................................... 9-8
9.3
Copying parameters .......................................................................................... 9-24
9.4
Setting calculation function .............................................................................. 9-26
9.5
Setting timer for calculation ............................................................................. 9-32
9.6
Setting for data display screen .......................................................................... 9-34
9.7
Setting for F value calculation (Setting common to all channels) .................... 9-39
9.8
Setting totalizing ............................................................................................... 9-41
9.9
Setting for messages ......................................................................................... 9-45
9.10 Unit definition ................................................................................................... 9-47
9.11 Setting for DI (external control unit) function .................................................. 9-48
9.12 Setting constant ................................................................................................. 9-50
9.13 Ethernet function setting ................................................................................... 9-51
9.14 Setting password for parameter setting ............................................................. 9-54
10. OPERATING MEMORY CARD .................................................................. 10-1
10.1 Displaying record data of memory card ........................................................... 10-1
10.2 Removing memory card (compact flash) ......................................................... 10-4
10.3 Totalizing start/stop setting............................................................................... 10-6
10.4 Totalize reset request ........................................................................................ 10-8
10.5 Function of reading setting from memory card (compact flash) ...................... 10-9
10.6 Function of writing setting in memory card (compact flash) ......................... 10-10
10.7 Setting password for memory card operation ................................................. 10-12
vi
INP-TN2PHL-E
11. MAINTENANCE AND INSPECTION ......................................................... 11-1
11.1 Recommended replacement cycle of parts ....................................................... 11-1
11.2 Calibration ........................................................................................................ 11-1
11.3 Formatting the memory card ............................................................................ 11-1
12. CALIBRATION .............................................................................................. 12-1
12.1 Calibration method of measured values ........................................................... 12-1
12.2 Initializing the measured value ......................................................................... 12-3
13. TROUBLESHOOTING .................................................................................. 13-1
14. SPECIFICATIONS ......................................................................................... 14-1
APPENDICES ........................................................................................................ A-1
Appendix 1 Recording format (ASCII) ...................................................................... A-1
Appendix 2 Parameters that cannot be set during recording ...................................... A-3
Appendix 3 Parameters that cannot be set while totalizing is under way ................... A-3
Appendix 4 Opening the PHL record data in ASCII format on Excel ....................... A-4
Appendix 5 Timing of recording ................................................................................ A-5
INP-TN2PHL-E
vii
1. INTRODUCTION
We thank you for purchasing Fuji Paperless Recorder PHL.
The instruction manual describes installation, operation, and maintenance of Paperless Recorder. Read this
manual carefully before use.
1.1 Paperless recorder
(1) This recorder displays measured data in real time on the liquid crystal display. It is a paperless
type that is also capable of saving the measured data to a compact flash card.
(2) It can set up to 18 channels for the input types such as thermocouple, resistance bulb, and DC
voltage (or current).
(3) It allows the measured data saved to the compact flash card to be displayed on the display unit.
Use of the support software attached to the recorder allows the saved data to be displayed on a
personal computer.
1.2 Product check
Upon receiving the recorder unit, check the appearance for damage, and if the correct quantity of the
accessories are supplied.
Check on accessories
This recorder comes with the accessories shown in Fig. 1-1. Check that they are all present.
(1) Panel-mounting
bracket
(3) Panel packing
(2) PC support software
(CD-ROM)
(4) AC power cord
(5) Power supply
noise filter
Fig. 1-1 Accessories
Product name
(1) Panel-mounting bracket
PC support software instruction
(2) CD-ROM
manual
(3) Waterproof panel packing for front face
(4) AC power cord (2m)
(5) Power supply noise filter
INP-TN2PHL-E
1-1
Quantity
Panel-mounted Portable
–
2
1
1
1
–
1
–
1
1
1.3 Check on type and specification
Code symbols are marked on specification nameplates. Check the type as ordered. (The specification
nameplates are attached to the right of the case and at the rear of the display unit).
CODE SYMBOLS
Digit
Item
4 Number of input points
1 2 3 4 5 6 7 8
1
2
Mounting
Panel mount
Portable
(Note 3)
9
Display
11
Alarm (relay) output/DI
input board
1
2
English
12
V
Specifications
9-point input
18-point input
5
9 10 11 12 13
B1 2-E1
PHL
Communication/alarm
(open collector) output/
DI input/Ethernet
Note 1:
Note 2:
Note 3:
Without
With
E
(Note 1)
Without
RS485+DI+DO
Ethernet
(Note 3)
Ethernet+RS485
+DI+DO (Note 3)
0
1
Y
R
E
W
If you select 2 (18-point input) for the 4th digit of the code symbol,
you cannot select 1 for the 11th digit (alarm output/DI input board).
If alarm output/DI input for 18-point input is required, select R or W for the 12th digit
(communication/alarm output/DI input/Ethernet).
Portable type is not approved by UL and CE marking.
Portable type cannot be selected with Ethernet.
1.4 Handling memory card (Compact Flash)
– Cautions on handling
(1) Use a Compact Flash (sold separately) that we warrant its performance.
Use of a commercially available Compact Flash may cause failure.
1) When formatting the memory card, use a personal computer. (Refer to 11.3)
as FAT32, FAT16 or FAT
CAUTION
2) The memory card should be inserted in the proper direction and fixed securely
to the slot.
3) Don’t turn OFF the power or remove the card from the slot while data is being
written in or read from the card, or recorded data may be damaged or lost.
4) Measured data saved to the memory card should be backed up, if necessary.
5) Using CF card adaptor, please check how many capacities it can deal with. If
your CF card is out of the range, don’t format CF card using the adaptor.
When format CF card by the adaptor, you may find it complete format on the
Windows. But in that case, PHL might not read the card.
6) The compact flash card is a consumable item. If the following phenomena
take place, the card must have come to the end of its service life. Replace the
card in such cases.
• The number of recording file is found to be larger than expected even though
power failure did not occur or recording was not interrupted.
• The recording file loaded into the PC cannot be opened with the data viewer.
7) If you insert a large-capacity Compact Flash, the recorder's screen may stop
about 3 seconds. Recording is still performed normally during this period.
1-2
INP-TN2PHL-E
(2) Compact flash in the capacity range from 8MB to 2GB can be used.
Refer to the following tables for the storage capacity in the case of 9-channel recording (on
condition that no events such as alarms or messages are occurring, and that totalizing is stopped).
(The number of days required for 18-channel recording is approximately one half of those shown
in the table.)
Compact flash size
16MB
Display refresh cycle
Recordable capacity
(about)
1 sec
10 sec
30 sec
1 min
10 min
30 min
ASCII format
28 hours
11 days
35 days
70 days
2 years
5.7 years
Binary format
112 hours
44 days
140 days
280 days
8 years
22.8 years
64MB
Compact flash size
1 sec
10 sec
30 sec
1 min
10 min
ASCII format
112 hours
46 days
140 days
280 days
7.7 years
Binary format
448 hours
184 days
560 days
1 sec
10 sec
30 sec
ASCII format
18 days
187 days
1.5 years
3 years
Binary format
72 days
748 days
6 years
12 years
Display refresh cycle
Recordable capacity
(about)
256MB
Compact flash size
Display refresh cycle
Recordable capacity
(about)
1,120 days 30.8 years
1 min
Note: Refer to Item 9.1 “Basic Setting” for the selection of ASCII or binary format for data recording.
(3) Data write to the memory card is performed according to the following timing. If the power is
OFF in the writing cycle, note that the data will not be recorded.
Display refresh cycle
Write cycle
1 sec to 1min 2 min
1 min
2 min
3 min
5 min
10 min 20 min 30 min
3 min
5 min
10 min 20 min 30 min
Display refresh cycle
1 hour
2 hours
3 hours
4 hours
6 hours 12 hours
Write cycle
1 hour
2 hours
3 hours
4 hours
6 hours 12 hours
(4) The data recorded in the compact flash can be regenerated on the PC by using the data viewer
(contained in the attached CD-ROM).
If the data is recorded in ASCII format, it can be directly opened in a spreadsheet such as EXCEL.
However, large-amount data cannot be opened (about 10MB or larger in the case of 9-point input,
and about 5MB or larger in the case of 18-point input).
In those cases, read in data with the data viewer (contained in the attached CD-ROM), and perform CSV conversion to divide the file, which allows the data to be read in.
The data recorded in binary format cannot be directly opened in a spreadsheet such as EXCEL.
Refer to Item 9.1 “Basic Setting” for details.
Note : 1) Be careful not to make the size of a file too large even if a large-capacity CF card is
used. (Keep it to less than 10MB if possible.)
2) If the size of recording file becomes 256MB or more, a new file is created automatically
to continue recording.
(5) Removing memory card
By prohibiting the writing on the memory card, the card can be taken out even if the recording or
integration is not stopped. Refer to Item 10.2 “Removing memory card (compact flash)” for the
procedure.
CAUTION
INP-TN2PHL-E
Make sure to prohibit writing before removing the memory card, when using FTP
server function.
1-3
(6) About communication function
By connecting the paperless recorder to Ethernet, the following function can be used (when E or
W is selected for the 12th digit of the code symbols).
• FTP server function: Record files stored in the compact flash of the recorder can be downloaded
from the PC on the network using Web browser (Microsoft Internet Explorer) or DOS prompt.
• Web server function: Measurements of the recorder or event log on the network can be displayed using Web browser (Microsoft Internet Explorer).
• E-mail function: E-mails can be sent to specified addresses with the measurement of the recorder attached.
• MODBUS TCP/IP function: Settings of the recorder can be read or written from the PC on the
network using MODBUS TCP/IP function.
Ethernet
1-4
INP-TN2PHL-E
2. NAMES AND FUNCTIONS OF PARTS
2.1 Names and functions of parts
(1) Display unit
(5) Connector for
parameter loader
(2) Power switch
(3) Memory card slot
(6) Function keyboard
(4) Memory card ejection button
(1) Display unit
Allows the Real time trend screen, Bar Graph Display screen, Analog meter screen, Digital
Display screen, Totalizing data display screen, Historical trend screen and other various Parameter
Set screens to be displayed.
(2) Power switch
Used to turn the power ON or OFF.
(3) Memory card slot
Used for inserting the memory card
(4) Memory card ejection button
To remove the memory card from the slot, press this button.
CAUTION
1) If you want to remove the memory card while recording is in progress (while
REC in the display unit is highlighted) or during totalizing, refer to Item 10.2
or stop recording and totalizing before removing the memory card. Otherwise, the data cannot be recorded correctly, or the past data may be damaged.
(If the memory card is removed and inserted again while recording or totalizing is in progress, it is recorded as a new file.)
2) While the compact flash of the paperless recorder is accessed by FTP communication, do not take out the compact flash.
Furthermore, when the FTP server function is used, inhibit access to the
compact flash in the “Memory card abstract” screen, before taking out the
compact flash.
(5) Connector for parameter loader
When changing parameters by using a loader, connect the exclusive cable (optional cable:
PHZP0201) to the connector.
(6) Function keyboard
Used for operation, or setting and verifying each parameter.
INP-TN2PHL-E
2-1
Key name
(Record)
(Display)
Function
Used to start or stop recording.
Pressing once, starts recording. After that pressing once again, stops recording.
Used to switch display contents. Each time the key is pressed, the display is switched to q
→ w → e → r → t → y and returns to q.
q Real time trend display
Displays the measurement data of an arbitrary channel on data display screen (note 1)
w Key guidance
Key operation guidance appears.
e Bar graph/analog meter display
Displays the measured data of the channel in a bar graph (or analog meter).
At the shipment, it is set to display “Bar graph meter display”.
r Digital display.
Displays the measured data of the channel in numerical values.
t Totalizing data display
Displays the totalizing data of an arbitrary channel in numerical values.
y Event summary display
Displays the alarm summary or message summary.
Pressing this key on the parameter setting screen (note 2), the display is swithed to the Real time
trend display.
(Select)
Used to switch from the data display screen (note 1) to the parameter setting screen (note 2).
Pressing the key on the parameter setting screen switches to the screen one step up.
However, pressing the key on the menu screen does not change screens.
q Used for selection on the setting screen or registration of the set data.
(Entry)
w If the key is pressed while the scales are displayed on the real time trend display screen,
historical trend display screen (*1), or recorded data display screen, the channels for which
scales are to be displayed can be switched.
(Scale of ch1 → scale of ch2 → ….. → scale of ch9 → scale of ch1 → scale of ch2…..)
*1: The screen in the past of the data currently recorded
(Cursor)
q Used to select setting items.
w Used to increase or decrease numerical values.
e Pressing the
key on the real time trend displays the historical trend screen (*1).
At this time, the window can be scrolled using the cursor key.
r Pressing the
or
key on the real time trend display, bar graph/analog meter display,
digital display screen or totalizing data display screen is changed, as shown below.
Press
key : group 1 → 2 → 3 → 4 → 1 → ...
Press
key : group ... ← 4 ← 1 ← 2 ← 3 ← 4
*1: The screen in the past of the data currently recorded
Note 1 : See Item 7.4 for detail.
Note 2 : See Item 8.1 for detail.
2-2
INP-TN2PHL-E
2.2 Inserting and removing the memory card
The memory card is used for saving measured data. Before attempting to use the recorder, set it in the
recorder slot securely.
This section explains how to insert the memory card into or remove it from the slot.
(1) To insert memory card
Step 1) Open the panel unit.
Step 2) Insert the memory card into the slot at the
right side of the panel unit as shown in
Photo.
CAUTION
Insert straight the card in accordance with the photo, or the
inside pins might be broken. If
you insert with wrong direction,
the slot is broken.
(2) To remove memory card
Step 1) Press the memory card ejection button to remove the memory card from the slot.
CAUTION
q Do not remove the memory card
while data is written in it (while
the lamp indicating writing status
is kept on). Refer to Item 8.19
“Removing memory card (compact flash)” for the removal of the
memory card while recording is in
progress.
w After inserting the memory card
into the slot, don’t remove the
card until the recorder can acknowledge it.
e Be careful with static electricity
when removing the memory card.
INP-TN2PHL-E
2-3
Memory card ejection button
2.3 Recording data to memory card
(1) Recorded data:
Data can be recorded in the following three formats. Either ASCII or binary format can be
selected for recording. Refer to Item 9.1 “Basic Setting.”
Trend data
: Records the maximum and the minimum values, average value or instantaneous values of the measured value sampled at display update cycles.
Trend data file name to be created: S00****.FDT (**** is substituted by
four-digit numerical value.)
Refer to “Appendix 1 (1) Trend data file” for recording format.
Event data
: Records the information on occurrence or release of alarms and message
issuing information.
Event data file name to be created: A00****.FDT (**** is substituted by
four-digit numerical value.)
Refer to “Appendix 1 (2) Event data file” for recording format.
Totalizing data: Records the totalizing data every totalize recording cycle.
Totalizing data file name to be created as shown below.
Periodic
: T000000.FDT
Dairy
: D000000.FDT
Weekly
: W000000.FDT
Monthly
: M000000.FDT
Annual
: Y000000.FDT
Dairy (Time set) : R000000.FDT
External
: E000000.FDT
(2) Parameter save data:
Setting file: Stores the setting created on the recorder main unit or the parameter loader.
Name of setting file: PA00000.PHL
2-4
INP-TN2PHL-E
(3) Recording capacity:
It depends on the capacity of the memory card.
Refer to the following tables for the storage capacity in the case of 9-channel recording (on
condition that no events such as alarms or messages are occurring, and that totalizing is stopped).
(The number of days required for 18-channel recording is approximately one half of those shown
in the table.)
Compact flash size
16MB
Display refresh cycle
Recordable capacity
(about)
1 sec
10 sec
30 sec
1 min
10 min
30 min
ASCII format
28 hours
11 days
35 days
70 days
2 years
5.7 years
Binary format
112 hours
44 days
140 days
280 days
8 years
22.8 years
64MB
Compact flash size
1 sec
10 sec
30 sec
1 min
10 min
ASCII format
112 hours
46 days
140 days
280 days
7.7 years
Binary format
448 hours
184 days
560 days
1 sec
10 sec
30 sec
ASCII format
18 days
187 days
1.5 years
3 years
Binary format
72 days
748 days
6 years
12 years
Display refresh cycle
Recordable capacity
(about)
256MB
Compact flash size
Display refresh cycle
Recordable capacity
(about)
1,120 days 30.8 years
1 min
Note: Refer to Item 9.1 “Basic Setting” for the selection of ASCII or binary format for data recording.
(4) Recording cycle:
Refer to the following tables for the timing of writing the trend data to the compact flash.
The event data is written in the compact flash by the minute.
Display reflesh cycle
1 sec to 1min
2 min
3 min
5 min
10 min
20 min
30 min
1 min
2 min
3 min
5 min
10 min
20 min
30 min
Writing cycle
Display reflesh cycle
1 hour
2 hours
3 hours
4 hours
6 hours 12 hours
Writing cycle
1 hour
2 hours
3 hours
4 hours
6 hours 12 hours
(5) Timing to start recording:
The event data cannot be written in the compact flash until the first display refreshment cycle
passes by.
INP-TN2PHL-E
2-5
3. MOUNTING METHOD
This unit is designed to be panel mounted.
3.1 Mounting location
Select the following location for mounting the unit.
(1) A place that is not subject to vibration or shock.
(2) A place where there is no dust, dirt or corrosive gas.
(3) A place that is subject to little temperature variation and is in the range of 0 to 50°C.
(4) A place that is not struck directly by strong radiant heat.
(5) A place that is free from water drip or dew condensation in the range of 20 to 80%RH.
(6) A place that is well ventilated for the dispersion of heat generated from other devices.
(7) A space that is accessible for wiring, and maintenance and check.
(8) A place that is not affected by electromagnetic wave from wireless machine or
portable telephones.
∠α
(9) Mount the unit horizontally, with no tilt to the left or right (The forward tilt
should be 0° but the unit may be inclined 0 to 30° rearwards.
∠α = 60 to 90°
3.2 External dimensions and panel cutout dimensions
(unit: mm)
Mounting bracket
144
External dimensions
2 ≤ T ≤ 26
T
136.5
161
Panel
160
140
21.6
185
24.6 when waterproof packing is used
Note) If other instruments are placed under the recorder unit,
provide a space of 100 mm or more from the instrument or floor.
Panel cutout dimensions
Mounting 1 unit
(160 × n–22) +20
137 +1.5
0
137 +1.5
0
137
Mounting n units
+1.5
0
Note) When mounting n units, don't use waterproof packing.
INP-TN2PHL-E
3-1
3.3 How to mount the unit onto the panel
Panel
Mounting bracket
• Using the supplied mounting bracket, tighten the upper and lower screws unit the panel is fixed.
• The panel to be used should be more than 2 mm and less than 26 mm thick.
CAUTION
Excessive torque will cause damage to front panel frame or result in case
deformation.
Torque: 0.2 N·m
• If the panel front is subject to water splashes, use panel packing between the unit and panel.
3-2
INP-TN2PHL-E
4. WIRING
4.1 Before wiring
(Note) When cables are connected to terminals of the recorder unit, don’t apply pulling force to them
excessively. Excessive force to the terminal may result in damage to the terminal or cable.
(1) Use the power cable that has the performance equivalent to or higher than 600-V vinyl insulated
power cable.
(2) For the thermocouple input, be sure to use a compensated lead wire.
(3) Input signal cables should be wired separately as far as possible (30 cm or more) from power lines
and high-voltage lines to minimize the effect of inductive noise. Shielded cables should preferably be used. In this case, the shield braids should be earthed at one point.
(4) Up to 2 solderless terminals should be used when connecting cables to terminals. Be sure to use
an insulation cap.
(Note)
1) At the completion of wiring of the input terminals, be sure to close the rear cover to ensure
the compensation of reference contact when thermocouple input is used.
In case of thermocouple input, follow the steps to stabilize temperature at the terminal.
• Be sure to attach input terminal cover.
• Don’t use a thick cable to prevent the effect of radiation. It is recommended that the cable
with a diameter of 0.5 mm or less should be used.
• Don’t mount other instruments near a fan to keep temperature stable.
2) For connection of lead wires to terminals, use of sleeve-insulated clamping terminals is
recommended.
3) This product is provided with a built-in fuse that cannot be replaced by the customer. Therefore, we recommend you to separately provide adequate fuses externally. (Rating: 250V, 1A)
4) Don’t loosen screws that are secured to the terminal case and
power terminal.
INP-TN2PHL-E
4-1
For M3
screw terminal
4.2 Connection to terminals
(1) Input terminal:
Connect signal cable for each channel.
(2) Alarm relay (DO)/DI (External control unit):
Connect the output of alarm signals and the input of DI (external control) signals (for alarm [DO]
1 to 10 and DI [external control] 1 to 5)
(3) Power terminal:
Connect power cable to L/N terminals. Power source to be connected should be free from noise.
(4) Earth terminal:
Connect to “G” terminal (Class-D, 100Ω or less).
(5) Communication, alarm (open collector) output and DI terminal:
Connect the output of alarm signals and the input of DI (external control) signals (for alarm [DO]
11 and DI [external control] 6). And connect the communication signal cable to TRX (+) and
TRX (-).
(6) Alarm (open collector) output and DI input:
Connect the output of alarm signals and the input of DI (external control) signals (for alarm [DO]
12 to 28 and DI [external control] 7 to 10).
Do not loose.
3
1
1
4
3
5
2
1
6
4
5
Do not loose.
Note: Do not loose, or recorder can’t measure correctly at thermocouple input.
4-2
INP-TN2PHL-E
(1) Connection of input terminal
1) Input terminal No. is determined for each channel.
2) When changing the type of input signal (see Item 9.2) after purchasing the unit, connect input
terminals according to the relation between terminal No. and channel No..
Note: Don’t input huge signal that is out of range, or recorder is broken.
Channel 1 to 9
Input terminal
Thermocouple
Thermocouple
Resistance
Voltage
Voltage
Resistance
bulb
+
+
bulb
11
+
+
61
–
–
CH1
12
–
–
62
CH6
13
63
+
+
21
+
+
71
–
–
22
CH2
–
–
72
CH7
23
73
+
+
31
–
–
CH3
32
RCJ
33
+
+
41
+
+
81
–
–
CH4
42
–
–
82
CH8
43
83
+
+
51
+
+
91
–
–
CH5
52
–
–
92
CH9
53
93
Note) For current input, connect optional shunt resitors to the voltage input terminals.
Resistance
bulb
Voltage
Resistance
Voltage
bulb
Thermocouple
Thermocouple
CH6
CH7
+
+
–
–
+
+
–
–
+
+
–
–
+
+
–
–
+
+
–
–
+
+
–
–
CH1
CH2
CH3
RCJ
CH8
CH9
INP-TN2PHL-E
+
+
–
–
+
+
+
+
–
–
–
–
4-3
CH4
CH5
Channel 10 to 18
Input terminal
Thermocouple
Thermocouple
Resistance
Voltage
Voltage
Resistance
bulb
+
+
bulb
111
+
+
161
–
–
CH10
112
–
–
162
CH15
113
163
+
+
121
+
+
171
–
–
122
CH11
–
–
172
CH16
123
173
+
+
131
–
–
CH12
132
RCJ
133
+
+
141
+
+
181
–
–
CH13
142
–
–
182
CH17
143
183
+
+
151
+
+
191
–
–
CH14
152
–
–
192
CH18
153
193
Note) For current input, connect optional shunt resitors to the voltage input terminals.
Resistance
bulb
Voltage
Resistance
Voltage
bulb
Thermocouple
Thermocouple
CH15
CH16
+
+
–
–
+
+
–
–
+
+
–
–
+
+
–
–
+
+
–
–
+
+
–
–
CH10
CH11
CH12
RCJ
CH17
CH18
+
+
–
–
+
+
+
+
–
–
–
–
4-4
CH13
CH14
INP-TN2PHL-E
Wiring of input terminals
(2) DC current input
(1) DC voltage input
Shunt resistor (option)
(PHZP0101)
Not used
Not used
DC current input
Example 1) For 4 to 20mA and 10 to 50mA input,
10Ω±0.1% shunt resistance is used.
In this case, set the input range
to ±500mV (see Item 9.2).
Voltage conversion by shunt resistance of 10Ω
4 to 20mA DC : 40 to 200mV DC
10 to 50mA DC : 100 to 500mV DC
DC voltage input
(4) Resistance input
(3) Themocouple input
b
B
A
Not used
Compensating
leads
Red(A)
White(B)
White(b)
Thermocouple
Note) Avoid using thermocouple input with
wiring parallel to other instruments.
Resistance bulb
Note)
1) Input signals should be the same for every 2 channels.
Example) ch1: thermocouple
ch2: thermocouple
ch3: 5V
ch4: 5V
Any type of thermocouple can be set.
1 to 5V or 0 to 5V can be set.
For the setting method, see Item 9.2.
2) Don’t remove RCJ module, or indication of process variable is not correct at thermocouple
input.
INP-TN2PHL-E
4-5
(2) Alarm relay output (DO)/DI (external control unit) (Option)
Note: This option is in case of 11th digit of CODE SYMBOLS is “1”. If the number of input
points is 18, it cannot be mounted.
About external control unit (DI)
1) This instrument is provided with the function of performing “start/stop of recording operation,“
“F-value computation resetting,” “Start/stop of totalizing,” and “Message display” in response
to the contact signals (DI) received from outside the instrument.
Alarm output/DI input terminal
211
231
212
232
213
233
214
234
215
235
216
236
217
237
218
238
219
239
220
240
221
241
222
242
223
243
224
244
225
245
DI1
DI2
DI3
DI4
DI5
DO1
DO2
DO3
DO4
DO5
DO6
DO7
DO8
DO9
DO10
DI1
DI2
DI3
For DI function,
see"Setting of DI function".
DI4
DI5
Note 1) DI (external control) unit is not insulated and should be used with a relay connected to
the outside.
External contact capacity: 20V/0.05A DC, 1a contact
Note 2) DI (external control) unit is operated as follows when the front switch is pressed.
The unit action will not be affected by items in the table.
(1) Recording start/stop
(2) F value calculation reset
Front key
External control
Recording start/stop by DI
ON
In F value
calculation
OFF
In recording
Recording start
stop
OFF
Reset the value
Keep on calculating
Recording start
Recording stop
In recording
External control
ON
Recording stop
(3) Totalize reset
(4) Totalize start/stop
External control
ON
In Totalizing
External control
OFF
Reset the value
ON
In totalizing
stop
Keep on totalizing
In totalizing
OFF
Totalizing start
Totalizing stop
(5) LCD ON
External control
ON
In LCD off
OFF
LCD ON
4-6
INP-TN2PHL-E
About alarm output (DO)
1) Alarm setting is provided at 4 points for each input channel. Up to 10 points for alarm output
can be set as an option.
2) When an alarm occurs, the relevant terminals are shorted (ON).
1a contact output: Relay contact capacity : 150V AC/3A, 30V DC/3A (resistive load : DO1)
: 240V AC/3A, 30V DC/3A (resistive load : DO2 to
DO10)
DO1
Alarm output/DI input terminal
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
DO2
DI1
DI2
DI3
DI4
DI5
DO1
DO2
DO3
DO4
DO5
DO6
DO7
DO8
DO9
DO10
DO3
DO4
DO5
DO6
DO7
DO8
DO9
DO10
Note) If lamps are provided on the outside, set a resistor to prevent rush current. When
relays or solenoids are used, set elements for contact protection (diodes or surge killers, etc).
INP-TN2PHL-E
4-7
(3) Communication, Alarm output (DO)/DI input
Note) This option is in case of 12th digit of CODE SYMBOLS is “R” or “W”.
1) About communication
This is for digital communication function with another instruments. This specification is shown
below.
Item
Electrical specification
Transmission system
Synchronizing system
Connection format
Number connectable units
Transmission distance
Transmission speed
Data format
Transmission code
Error detection
Isolation
Specification
Based on EIA RS-485
2-wire, semi-duplicate
Start-stop synchronous system
1:N
Up to 31 units
500m max. (total extension distance)
9600, 19200 bps
8 bits
Data length
1 bit
Stop bit
none, even, odd (selectable)
Parity
HEX value (MODBUS RTU mode)
CRC-16
Functional isolation between transmission circuit and
ground (withstand voltage : 500V AC)
Communication terminal
Shield
TRX2(-)
TRX1(+)
4-8
INP-TN2PHL-E
2) About external control unit (DI)
This function is the same as the previous page.
Alarm output/DI input terminal
24VdC
13
12
11
10
9
8
7
6
5 (DI10)
4 (DI9)
3 (DI8)
2 (DI7)
1
PCD
VPD
PCD
DO12
DO13
DO14
DO15
DO16
DO17
DO18
DO19
DO20
DO21
DO22
DO23
DO24
DO25
DO26
DO27
DO28
DI7
DI8
DI9
DI10
VPD
VPD
24Vdc
1
14
13
25
6
7
8
9
10
11
12
15
16
17
18
19
20
21
22
23
24
2
3
4
5
DI6
DIO(+24V)
PCD
DIO(0V)
DO11
PCD
DI6
SHLD
(shield)
TRX2
–
TRX1
+
(–)
(+)
MODBUS
communication
25
24
23
22
21
20
19
18
17
16
15
14
PCD
Note 1) DI (external control) unit is not insulated and should be used with a relay connected to
the outside.
External contact capacity: 20V/0.05A DC, 1a contact
Note 2) DI (external control) unit is operated as shown in page 4-6, Note 2), through (1) to (5)
when the front switch is pressed.
The unit action will not be affected by items in the table.
INP-TN2PHL-E
4-9
3) About alarm output (DO)
1) Alarm setting is provided at 4 points for each input channel. Up to 10 points for alarm output
can be set as an option.
2) When an alarm occurs, the relevant terminals are shorted (ON).
This output is open collector. Ratings are as follows:
30V DC/100mA (resistive load)
24VdC
13
12 (DO18)
11 (DO17)
10 (DO16)
9 (DO15)
8 (DO14)
7 (DO13)
6 (DO12)
5
4
3
2
1
25
(DO28) 24
(DO27) 23
(DO26) 22
(DO25) 21
(DO24) 20
(DO23) 19
(DO22) 18
(DO21) 17
(DO20) 16
(DO19) 15
14
PCD
VPD
PCD
VPD
VPD
24Vdc
DO12
DO13
DO14
DO15
DO16
DO17
DO18
DO19
DO20
DO21
DO22
DO23
DO24
DO25
DO26
DO27
DO28
DI7
DI8
DI9
DI10
DIO(+24V)
PCD
DIO(0V)
DO11
PCD
DI6
SHLD
TRX2
–
TRX1
+
(shield)
(–)
(+)
MODBUS
communication
1
14
13
25
6
7
8
9
10
11
12
15
16
17
18
19
20
21
22
23
24
2
3
4
5
DO11
PCD
Note) This is not relay output.
Do not input over rating voltage or current.
4-10
INP-TN2PHL-E
4) Ethernet
Note: Install the LAN cable far away from the power supply line or strong electric line as
possible to avoid the influence of induction noise.
(4) Caution on connection of input signal through barrier
1) Thermocouple input and resistance bulb input
Since the barrier internal resistance is added and causes an error in the measured value, perform
“Calibration of measured value” with the input connected to the barrier recorder.
For the calibration method, refer to Item 12.1.
2) When using Fuji Zener Barrier (PWZ), a power supply of 100V AC line (85 to 150V AC) should
be used to ensure safe operation of the unit.
INP-TN2PHL-E
4-11
4.3 Connecting recorder to loader
(1) When connecting the recorder to a loader, use optional PC loader communication cable
(PHZP0201) as shown below.
(USB cable)
The loader cable should be connected to USB port of PC.
CAUTION
Be sure to display the data display screen (refer to Item 7.4) instead of the parameter setting screen before using the loader. Otherwise, the set value may not be
written.
4-12
INP-TN2PHL-E
5. PORTABLE
5.1 Portable
• The instrument can be carried about easily holding the handle.
(Portable type is not approved by UL and CE marking.)
External view
5.2 Handling
Observe the following in handling the instrument.
(1) Preferable use environment
• A place not subjected to vibration or impact
• A place not subjected to dust or corrosive gases
• A place of ambient temperature of 0 to 40°C with minimum temperature change
• A place where the humidity is kept within the range from 20 to 80%RH and not subjected to
drops of water.
• A place provided with sufficient ventilation allowing the heat from the instrument to be discharged
• A place not subjected to the interference from electromagnetic waves by radio devices or mobile
phones
• A place where the instrument is not exposed to the risk of falling.
(2) Notes
• Use the stand in upright position.
• Be sure to return the rear cover to the original position after performing the wiring of the input
or the alarm (DO)/DI terminal.
• Be sure to turn off the power before performing wiring and inspection to avoid receiving electric shock.
INP-TN2PHL-E
5-1
5.3 Outside dimension (unit: mm)
15
144
136.5
208.5
20
Handle
140
49
160
21.6
185
Foot
Stand foot
Note: Use the stand in upright position.
5.4 External connection diagram
When the number of input points = 9: M3 screw
INPUT TERMINAL
Thermocouple
Voltage
T.C. Resistance
DC
bulb
R.T.D
+
+
61
–
–
62
CH6
63
+
+
71
–
–
72
CH7
73
RCJ
CH8
CH9
+
+
–
–
+
+
–
–
81
82
83
91
92
93
ThermoResistance couple Voltage
bulb
DC
T.C.
R.T.D
+
+
11
–
–
CH1
12
13
+
+
21
–
–
22
CH2
23
+
+
31
–
–
CH3
32
33
+
+
41
–
–
CH4
42
43
+
+
51
–
–
CH5
52
53
5-2
INP-TN2PHL-E
When the number of inputs = 18: M3 screw
INPUT TERMINAL
ThermoThermocouple
Resistance couple Voltage
Voltage
T.C. Resistance
bulb
DC
T.C.
DC
bulb
R.T.D
+
+
R.T.D
111
+
+
161
–
–
CH10
112
–
–
162
CH15
113
163
+
+
121
+
+
171
–
–
122
CH11
–
–
172
CH16
123
173
+
+
131
–
–
CH12
132
RCJ
133
+
+
141
+
+
181
–
–
CH13
142
–
–
182
CH17
143
183
+
+
151
+
+
191
–
–
CH14
152
–
–
192
CH18
153
193
When the 11th digit of CODE SYMBOLS=1
(With Alarm output (DO)/DI input)
Alarm output/DI input terminal
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
INP-TN2PHL-E
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
DI1
DI2
DI3
DI4
DI5
DO1
DO2
DO3
DO4
DO5
DO6
DO7
DO8
DO9
DO10
5-3
When the 12th digit of CODE SYMBOLS=R or W
(With communication and alarm output/DI input)
DIO (+24V)
DIO (0V)
13
12
11
10
9
8
7
6
5
4
3
2
1
25
24
23
22
21
20
19
18
17
16
15
14
DO11
DI6
Shield
TRX2(–)
TRX1(+)
PCD
VPD
PCD
VPD
VPD
24Vdc
DO12
DO13
DO14
DO15
DO16
DO17
DO18
DO19
DO20
DO21
DO22
DO23
DO24
DO25
DO26
DO27
DO28
DI7
DI8
DI9
DI10
DIO(+24V)
PCD
DIO(0V)
DO11
PCD
DI6
SHLD
TRX2
–
TRX1
+
(shield)
(–)
(+)
MODBUS
communication
1
14
13
25
6
7
8
9
10
11
12
15
16
17
18
19
20
21
22
23
24
2
3
4
5
PCD
5-4
INP-TN2PHL-E
6. DISPLAY FUNCTION
6.1 Basic composition of Data Display screen
yMemory card
loading display
uMemory card oAlarm display
indicator
tMemory card
writing status display
!0Totalizing indicator
eParameter memory
lamp
qName of
screen
rRecord display
wClock
display
iData display
area
q Name of screen
Displays the screen name (“Display Name”) that was set arbitrarily.
w Clock display
Displays date and time (Year/Month/date).
e Parameter memory lamp
If the lamp blinks in red, it means that parameters are not saved to the flash memory. Save the set
value by selecting “Menu” / “Parameter setting” / “Basic setting” / “Register data” and press the
key.
r Record display
“REC” is lit when the measured data is being recorded. On the “Real Time Trend” screen, data
will be displayed only when the recorder is in recording.
t Memory card writing status display
It is lit when measured data is being written in a memory card.
y Memory card loading display
It indicates the loading state of the memory card.
Blinks
: shows the state where the memory card is not loaded in the slot.
Green display: shows the state where the memory card is loaded and can be pulled out.
Red display : shows the state where the memory card is loaded but must not be pulled out.
u Memory card indicator
It indicates how much of the memory card has bee used in graphs. At 90%, it turns red. At
100%, the recorder stops recording. Replace the memory card before it is used up.
i Data display area
It displays measured data in real time trend, bar graph, analog meter, digital display, totalizing or
event summary on the screen. (See Item 6.2 to 6.4.)
INP-TN2PHL-E
6-1
o Alarm display
It displays alarm information that occurs at present (channel No. and alarm No.).
If more than 1 alarm occurs, it displays one alarm after another in every 3 seconds.
!0 Totalizing indicator
While totalizing is in progress, the totalizing mark ( ) appears at the bottom of the letter T.
When totalizing is not in progress, only the letter T is displayed. Refer to Item 6.5 for details of
totalizing screen.
6-2
INP-TN2PHL-E
6.2 Real time trend display of measured data
Measured data can be displayed in waveforms. The vertical or horizontal directions can be selected by
setting. By pressing t or s key, four screens with different display contents (scale display and
screen structure contents [group configuration], Tag No. unit display, etc.) can be selected one after
another.
Vertical trend
Horizontal trend
Date and Time
(Year / Month / Day hour : minute : second)
(24-hour display) Time scale display
Trend display
Display division
Display division
Trend display
Measured value
display of each
channel
(point value)
Measured value
display of each
channel
(point value)
Time Time scale display
(hour: minute)
Correct time may not be displayed
Measured value
(24-hour display)
because there may be a case where
display in TAG No.
some digits of the time display are
or the unit is also
lacked.
available.
∗) The screens consist of those selected in “Menu” / “Parameter setting” / “Display setting”.
Note: If the display group setting has been made less than four channels, the trend screen for four
channels (historical screen, bar graph screen, digital screen and totalizing screen) appears.
Trend screen for four channels
2 items are displayed.
Large charactor
INP-TN2PHL-E
6-3
(1) The display unit allows measured data to be displayed in waveforms only when recording. If the
recorded values exceed the limits of 0 % and 100%, they will be displayed at 0% and 100% positions, respectively. If waveforms of more than 1 channel are displayed at the same position, the
trend lines overlap each other. In this case, color of the channel with the largest number is given
priority over those of other channels. (Example: In the case of ch2 and ch8, the color of ch8 is
displayed.)
(2) Display refresh cycles are selectable from parameters of 1 sec to 12 hours. Relations between the
parameter and chart speed are shown in tables below. After the start of the recording, the initial
refresh cycles will start at the time of 00: 00: 00 when the recording is continued.
(Example) When display refresh cycles are set to 1 minute, it will start at the next cycle of
m hour: n minute: 0 second.
Display refresh cycle (sec)
1
2
3
5
10
20
30
1296
648
432
260
130
65
43
Display refresh cycle (min)
1
2
3
5
10
20
30
Chart speed (mm/h) as converted
22
11
7.2
4.3
2.2
1.1
0.7
Display refresh cycle (hour)
1
2
3
4
6
12
0.36
0.18
0.12
0.09
0.06
0.03
Chart speed (mm/h) as converted
Chart speed (mm/h) as converted
(3) The Historical Trend screen is displayed by pressing the down cursor key (▼) when the Real Time
Trend is displayed. This screen allows currently recorded waveform data to be read from the memory
card, tracing back to the past. To return to the Real Time Trend screen, press the
key.
(4) The recorder performs the recording by pressing
, and it displays waveforms without inserting
the memory card into the slot. In this case, some 400 data can be displayed in historical trend.
However, the data exceeding 400 items will be deleted. So, be sure to insert the memory card in the
recorder slot before starting the recording.
(5) If the power is turned OFF while recorder is writing data to memory card, the data written in the
memory card will be destroyed. Be sure to press the
key to stop the recording, and then turn
OFF the power.
(6) If the input signal is burnt out, or over/under range is displayed, the recording line is displayed at 0%
or 100% position (at 100% position if the signal is burnt out). Note, however, the line is displayed
at the position equivalent to 0.26V for 0-5V input with the input kept open, and at the position
equivalent to 260mV for 0-500mV input with the input kept open.
6-4
INP-TN2PHL-E
6.3 Display of measured data in bar graphs or analog meters
The measured data can be displayed either in bar graphs or analog meters. The display type can be
selected. Please refer to Item 8.3 “Basic operation of setting screen,” and Item 9.6 “Setting method of
data display screen.”
1.
Display the measured data in a bar graph.
Scale display
bar graph display
Measured value
display of each
channel
(instantaneous
value)
2.
Display the measured data in analog meters.
Note that the analog meter display is allowed only for the first 4 channels of the group screens
selected for the analog meter by screen setting. For example, if No.1=ch5, No.2-None,
No.3=None, and No.4=ch1 are selected, the analog meter display will be as follows: upper left:
ch5, upper right: ---, lower left: ---, and lower right: ch1. Only the meter scale is displayed for the
part ---.
(1) Setting of display ranging from 0 to 100% is displayed in bar graphs.
(2) Display refreshment cycles are fixed to 1 sec.
(3) The recorder displays measured data even when it stops recording.
INP-TN2PHL-E
6-5
6.4 Digital display of measured data
Measured data is displayed in numerical values.
Display name
Channel No.
TAG name
Unit
Display of
measured value
Alarm No.
occurred
(1) Measured values of each channel are displayed in digital value.
(2) Display refreshment cycles are fixed to 1 sec.
(3) When an alarm occurs, Alarm No. at the channel is displayed in red.
6.5 Totalizing data display
Channel No.
TAG name
Totalize tag
Totalize calculation
Totalize type
Unit
(1) The displayed value depends on the setting of parameter, “Reset operation.”
If the setting is ON, totalized value is recorded at every totalize base time.
If the setting is OFF, the sum total value from the totalize start time is displayed.
(2) Display update cycle is fixed to 1 second.
6-6
INP-TN2PHL-E
(3) The value of totalized data to be recorded depends also on “Reset operation.”
If the setting is ON, totalized value is recorded at every totalize base time.
If the setting is OFF, sum total from the totalize start time is recorded.
Example: The data at the flow rate of 100L/hour is recorded as follows.
Totalize reset
Elapsed time
OFF
ON
1 hour
100
100
2 hours
200
100
3 hours
300
100
(4) Totalize calculation is not reset even if the power is interrupted.
Upon restoration of the power, totalize calculation resumes starting from the data before the
power interruption.
(If the file in the CF card used before the power interruption is lost at the time of power restoration, a new file is created. The data during the power interruption is not added.)
(5) The instrument can operate not only as a totalizer but also as a timer or a counter depending on
the setting of “Totalize calculation.”
a) If the setting is Totalizer, totalize function is performed.
b) If the setting is Counter, the number of times of DI ON or alarm ON during the totalize
period is displayed and recorded.
c) If the setting is Timer, the duration of DI ON or alarm ON during the totalize period is
displayed and recorded.
In all of the above cases, time is displayed based on the time set in a parameter, “Totalize base
time,” with all digits to the right of the decimal point discarded.
(6) While totalize calculation is suspended, totalize data is not displayed. It is not displayed, either,
while totalize calculation is suspended with “Daily (Time set)” or “External” selected as Totalize
type.
(7) On totalize 4-channel display screen, totalize start/stop time and the previous totalized value are
displayed.
INP-TN2PHL-E
6-7
6.6 Event summary display
Alarm information and message information history can be displayed.
The contents of messages can be displayed as message information.
Message
Page of screen
New
Old
(1) A maximum of 180 events can be displayed on the screen.
(2) Page scrolling can be performed by pressing t or s key.
(3) When events occur, they are displayed on the screen despite in the recording state. If the recorder
is not in the recording state, events are not recorded in the memory card.
(4) Once displayed, the event is kept displayed until the power is turned off (turning off the power
clears the event buffer).
(5) Press the
key to switch between message display and message summary display. The message contents appear initially.
(6) How to view the event summary is shown below.
(7) When the battery for backup is empty, power off and power on are not displayed.
Example of alarm summary
Message summary
ALM ON CH3 – 1H
Alarm summary
(Alarm ON)
Setting alarm No.
(1 to 4) and alarm
types (H and L)
Channnel No.
(1 to 30)
Alarm (ON/OFF)
Example of message summary
Message NO. 03
Message No. that occurred
Note) Message No. means the message
that is defined by selecting “Parameter
Setting” → “Message Setting”.
6-8
INP-TN2PHL-E
6.7 Ethernet log display
The use information of FTP, Web, E-mail, and MODBUS TCP/IP functions can be displayed.
Communication connection lamp
(1) Up to 180 communication items can be displayed.
(2) Pages can be turned using horizontal cursor key.
(3) The log appears every time communication is carried out irrespective of the state of recording.
(4) Once displayed, the contents of communication are kept displayed until the power is set to OFF.
(Communication buffer is cleared when the power is set to OFF.)
(5) Details of the display are as follows.
Communication contents display
• E-mail transmission display (E-mail No. is E-mail trigger No.)
E-mail sent
: “E-mail No.1”
E-mail send error
: “E-mail No.1 NG”
• FTP communication display
FTP server log in
: “FTP LOGON USER1”
FTP server log off
: “FTP LOGOFF USER1”
• MODBUS TCP/IP communication display
INP-TN2PHL-E
Communication start
: “MODBUS Start”
Communication stop
: “MODBUS Stop”
6-9
6.8 Historical trend display
Pressing the ▼ key on the real time trend screen, and following screen as shown below is displayed.
This screen indicates the history of currently recorded data.
Time at cursor position
Cursor
Measured value at cursor position of
each cannnel(Min and Max values)
(1) It allows the data recorded in the memory card to be displayed. The display can be scrolled by
using the cursor expressed in a white dotted line. The cursor can move vertically the (▲ or ▼)
key or horizontally the (tor s) key. Depending on recording type, either average, point or Min.
value or Max. value at the position of the cursor are displayed at the lower part of the screen.
(2) Recording start/stop cannot be performed on the screen. To do this, switch the “Historical Trend”
screen to “Real Time Trend” screen. However, this “Historical Trend” screen cannot be shifted to
the “Parameter Set” screen. To shift the “Real Time Trend” screen, be sure to press the
key.
(3) The data that can be displayed on the historical trend screen is the one currently recorded or the
data held immediately before the recording is stopped. The data that was recorded in the past and
whose recording was then stopped must be displayed on the “record data display” screen (refer to
Item 10.1), or reproduced on the PC using the data viewer.
The following items are displayed on the historical trend screen based not on the setting of the
past recording but on the currently selected values.
• Trend direction
• Number of screen partition
• Trend scale display
• Color bar display selection
6-10
INP-TN2PHL-E
(4) Press the
key while the historical trend screen is displayed, and following “Display time
setting” screen appears.
key.
Enter the time of currently recorded data you want to display and press the
Then, PHL displays historical trend data at entered day and time.
To display past data, entered day and time appears the bottom of the historical screen. To display
farther data, entered day and time appears the top of this screen.
6.9 Display on the occurrence of main unit failure
(1) Display at CF card memory FULL
If the memory of the CF card becomes full, recording is stopped with the following message
displayed on the trend screen, etc. (totalizing is not suspended). Immediately replace the CF card.
(2) Display at the end of battery life
If the battery voltage becomes low, the following message appears on the trend screen, etc.
Immediately stop the recording and totalizing, and ask your distributor for repair.
INP-TN2PHL-E
6-11
6.10 Cautions about power ON/OFF
(1) Recording state and record file
If the power is turned OFF when the recorder is in the recording, data written in the memory card
key, and then turn OFF the power.
may be damaged. Be sure to stop recording by pressing
In addition, if the power is OFF with the recorder in the recording, the recorder will start recording when the power is turned ON again. In this case, data will be recorded as a new file.
(2) Recording set values
After parameters have been set, register the set values by selecting “Basic settng” / “Register
data”, or they will return to the former values when power is turned OFF.
(3) Clock function
The clock is backed up by an internal lithium battery. The battery life is expected to be about 10
years at normal temperature. Although there is no need to set the clock when the power is turned
ON, an error may occur every time the power is turned ON/OFF (about 1 sec per ON/OFF operation).
(4) If the power is turned off due to a power failure and turned on again while recording is in
progress, a message “Power & Rec.ON.” appears at the top of the event file and event display.
(5) If the power is turned off, totalizing resumes when the power is turned on again, beginning from
the value before the power off. Data is recorded in the totalize file used before the power off.
(Note that if the file used before the power off is lost from the CF card, a new file is created and
recording is restarted.)
6-12
INP-TN2PHL-E
7. OPERATION AND ACTIONS
7.1 Before running the recorder
Check the following points before starting operation.
Loading the memory card
(1) Inserting and removing the memory card·············································· See Item 2.2.
Wiring
(1) Input terminals······················································································· See Item 4.2.
(2) Alarm terminals (option)········································································ See Item 4.2.
(3) Power and ground terminals·································································· See Item 4.2.
Conformity of input connection to recording channel
(1) Channel settings····················································································· See Item 9.2.
INP-TN2PHL-E
7-1
7.2 Power ON and state
(1) Open the panel unit. Turn “ON” the power switch at the upper center of the panel unit.
(2) After power ON, the self-check function starts up.
(3) Insert the memory card. Check if the unit is fixed in the slot, as viewing the memory card load
indicator. When you insert CF card to recorder, see the “Memory card load indicator” and check
the status of CF card (refer to Item 6.1). If indicator blinks in red, remove the CF card and then
insert again. After this operation, if it keeps on blinking in red, it might be broken.
Memory card load indicator
Memory card indicator
(4) Measured data are displayed for each channel.
Measured data for
each channel
* TAG. No. or the unit display is also available according to screen configuration setting.
7-2
INP-TN2PHL-E
7.3 Stopping and starting the recording operation
(1) Recording start
1) To start the recording, press the
key, and password input screen appears. If password has
not been set, this screen doesn’t appear. Recording password setting parameter, “Record Password” is as shown below.
Menu / Parameter setting / Config and rec password set
See Item 9.13 for detail.
Input correct password, then the REC lamp is lighted and measured values are displayed in
waveforms on the data display unit. Also, it starts saving the measured values to the memory
card.
* Recording is performed at the timing described in “Appendix 5 Timing for recording.”
ON
Waveforms of
measured values
Press
2) When Record password has been established, the following password screen appears. Enter the
password. If the entered password is correct, the recording is started.
3) If the CF card is not inserted, the following message appears. Press the
ing. Press the
key if you do not want to start recording.
key to start record-
Note: If recording is attempted with CF card not inserted, the result cannot be recorded.
INP-TN2PHL-E
7-3
(2) Recording stop
1) To stop recording, press the
key. The following message appears. To stop the recording,
key, and press the
key to continue recording.
press the
2) After the stop of the recording, the REC lamp comes off. The trend display on the data display
unit stops. In this case, even if there is some data that are not yet written in the memory card, the
unit writes them in the card until the recording is finished.
OFF
Previously recorded
waveforms
Press
(3) When Record password has been established, the following password screen appears. Enter the
password. If the entered password is correct, the recording stop confirmation screen appears.
7-4
INP-TN2PHL-E
7.4 Switching data display screens
Data display screens include real time trend screen, bar graph (analog meter) screen, digital screen and
totalizing screen. Every time the
key is pressed, the screen switches to another one. To display
the historical trend screen, press the
key in the real time trend screen.
Press the
or
key in the real time trend screen to switch to each group screen.
* If group screens are switched in high speed, the color on the color bar may not be displayed correctly. Display the screen once again in such cases to restore proper color display.
Refer to Item 9.6 for selection of bar graph/analog meter display.
The structure of the data display screen is as follows.
Group 1
Group 2
Group 4
Real time
trend screen
(Refer to
Item 6.2.)
The key operation procedure
on the data display screen is
displayed at the top of the
real time trend screen.
Key operation
guide display
Historical trend screen
(Refer to Item 6.8.)
(Groups cannot be switched
on this screen.)
Bar graph screen
(Refer to Item 6.3.)
and analog meter
screen (Refer to
Item 6.3.)
Digital screen
(Refer to
Item 6.4.)
Totalizing data display screen
(Refer to Item 6.5.)
INP-TN2PHL-E
Event summary screen
(Refer to Item 6.6.)
7-5
Ethernet log screen
(Refer to Item 6.7.)
7.5 Display of alarm
(1) Alarms that occurred on the Trend Display, Bar Graph and Digital Display
screens:
When an alarm occurs, its content is displayed.
(The display is kept on until the alarm is reset.)
Example of alarm display
Alarm type
Alarm No.
Channel No.
It is indicated that an alarm of alarm No.1
and alarm type L occurs at channel 1.
Note) If an alarm occurs on the “Digital Display” screen, Alarm No. at left of “Measured value
display” is lighted in red.
Alarm No.
* If an alarm occurs against the current input, the alarm contents (and not the past alarm record) are
displayed on the historical screen and the record data display screen of the memory card.
7-6
INP-TN2PHL-E
8. SETTING AND CHECKING PARAMETERS
8.1 Setting and checking
Follow the description of Item 8.2 “Outline of parameter setting procedure” to enter into each screen,
and then follow the description of Item 8.3 “Basic operation of setting screens” to make parameter
setting.
(1) Parameters are factory-set as given in Item 8.1 table(1). Turning on power as they are initiates
operation (indication and recording). Change the parameter setting as required.
(2) Recording range consists of multi-ranges. Set the range as desired. The input types are the same
for every 2 channels.
(3) Alarms, TAG No. and messages are not set. Set them as needed. An input filter is set at 3 seconds.
(4) Press the
key in the real time trend display screen to display the “Menu” screen. Refer to
Item 8.2 for the contents and the operation of the “Menu” screen.
INP-TN2PHL-E
8-1
(5) To go to “Parameter setting” screen, “CF manager and Totalize exe”. screen or “Calibration
password” screen, you must enter 4-digit password when you have already entered each password.
Example: Parameter setting screen
(in case of incorrect password)
,
,
keys : To move the cursor
keys : To change numerical value
(in case of correct password)
8-2
INP-TN2PHL-E
Note) After setting the parameters, select “Basic setting” / “Register data” in order to save the
key. So, the
set information to a flash memory. To reset parameter set values, press
key twice.
following message appears. Press the
The parameter has been reset.
INP-TN2PHL-E
8-3
Table (1)
Parameters as set by factory (initial values) (1/2)
Parameter name Setting at delivery (Default value)
Display refresh cycle
: 1 second
Basic setting
Display compression
: 1/1
Alarm hysteresis
: 0.2%
Alarm latch
: OFF
LCD lights out time
:0
*1
DO output at memory FULL: None
DO output at battery END: None
File division cycle
: No division
File overwrite
: OFF
Date format
: yyyy/mm/dd
Channel setting
Math channel
setting
Setting range
1 second to 12 hours
1/1, 1/10, 1/30, 1/60
From 0.00 to 100.00%
OFF, ON
0 to 60 minutes
None, DO1 to DO28
None, DO1 to DO28
No division, 1 hour, 1 day, 1 week, 1 month
OFF, ON
yyyy/mm/dd, dd/mm/yyyy, dd-mmm-yy,
mm/dd/yyyy, mmm-dd-yy
Select language
: English
English, French
0 to 255
MODBUS station No. : 1
MODBUS communication baud rate: 19200 9600, 19200 bps
None, Odd, Even
MODBUS parity bit
: Odd
OFF, ON
Front communication : ON
ASCII, Binary
Record data format
: ASCII
Time setting
:
Register data
:
Skip, K, E, J, T, R, S, B, N, W, L, U,
Input type: K-Type TC
PN thermocouple, Pt100, JPt100, Ni100, Cu50,
(K thermocouple)
Pt50, 50mV, 500mV, 1-5V and 0-5V range
Up to 8 characters
TAG1: TAG ∗∗ (∗∗: channel No.)
Up to 8 characters
TAG2
: Blank
°C, °F, Engineering unit in case of voltage input
Unit
: °C
Input range (range start/end): 0 to 1200 Engineering value
Decimal point position : ∗∗∗∗.∗
Input filter
: 3 seconds
0 to 900 seconds (In increments of 1 second)
Subtraction channel
: None
0 to 30 (No subtraction at 0)
PV shift
: 0.0
Engineering value –3276.7 to 3276.7
PV gain
: 100%
0.00 to 327.67%
F value calculation function: OFF
OFF, ON
Display color: depends on channel No. 14 colors
Recording type:
Instantaneous value recording, average value
Maximum/minimum value recording
recording, maximum/minimum value recording
Recording mode
: With record With record/Display only
Totalize setting
Totalize tag: STAG ∗∗ (∗∗: channel No.) Up to 8 characters
OFF, ON
Totalize calculation : OFF
Periodic, Daily, Weekly, Monthly, Annual,
Totalize type
: Periodic
Daily (Time set), External
Digital input
: DI1
Digital input, Channel alarm
Totalize base time : /h
/s, /min, /h, /day
Reset operation
: ON
OFF, ON
Can be arbitrarily selected
Totalize unit
:
Engineering value
Totalize cut value
: 0.0°C
1 to 32767
Totalize scaling value: 1
Totalize reset input : None
None, Digital input, Channel alarm
Alarm setting
Alarm No. 1 type
: OFF
OFF, H, L
Set point
: 0.0°C
Engineering value
DO relay No.
: None
DO1 to DO28
From alarm No. 2 to No. 4
There are the same items above.
Formula setting: All formula are blank Calculation: +, -, ∗, /
Function: ABS, POW, SQR, LOG, LN, EXP, RH,
MAX, MIN, H-P, L-P, AVG, SUM
Input: Input channel, Totalizer input, Digital input,
Communication input, Constant, Temporay data
Tag1: TAG ∗∗ (∗∗: channel No.)
Up to 8 characters
TAG2
: Blank
Up to 8 characters
Unit
: °C
Engineering unit
8-4
Remarks
*1
LCD keeps
turning on when
set “0”.
Set the same
input type for
every 2 channels.
INP-TN2PHL-E
Table (1)
Parameters as set by factory (initial values) (2/2)
Parameter name Setting at delivery (Default value)
Measuring range (range start/end)
Math channel
0.0 to 500.0
setting
Decimal point position : ∗∗∗∗∗.∗
Engineering range (range start/end)
0.0 to 500.0
Square rooter
: OFF
Logarithmic display
: OFF
Input range (range start/end): 0 to 1200
Input filter
: 3 seconds
Subtract channel
: None
PV shift
: 0.0
PV gain
: 100.00%
: 1 min
Math timer setting H-P, L-P timer cycle
AVG timer cycle
: 1 min
SUM timer cycle
: 1 min
Display screen
Trend back color
: White
setting
Historical back color
: Black
Display configuration:
Display setting
No. 1 to 9 = ch1 to 9
F value calculation Decimal point position : ∗∗∗∗∗.∗
setting
Manual reset
: OFF
Totalize base time
: 00:00
Totalize setting
Totalize cycle
: 1 hour
Weekly base day
: Sunday
Monthly base day
:1
Start time, Stop time: 00:00 to 00:00
External input
: DI1
: Blank
Message setting Message
: Blank
Original unit definition Unit
DI setting
DI function: Function invalid
Constant setting
Constant
:0
Ethernet setting
IP address
Subnet mask
Default gateway
FTP server function
FTP access control
Web server function
E-mail function
MODBUS TCP/IP
SMTP IP address
Sender’s mail
Add
Name
Receiver’s mail
Add1 to Add8
Triigger timing
: 0.0.0.0
: 0.0.0.0
: 0.0.0.0
:
:
:
:
:
: 0.0.0.0
Alarm Channel
Alarm No.
Title
Text1, 2
PV value affixation
Receiver’s add No.
Mail send test
User name
Password
User Level
Security mode
Password
Record Password
:1
:1
: Blank
: Blank
:
:1
:
: Blank
: Blank
: administrator
: Password
: 0000
: 0000
E-mail setting
E-mail trigger
setting
User account
setting
Config and
record password
INP-TN2PHL-E
: Blank
: Blank
: Blank
: None
Setting range
Engineering value
∗∗∗∗∗∗, ∗∗∗∗∗.∗, ∗∗∗∗.∗∗, ∗∗∗.∗∗∗, ∗∗.∗∗∗∗
Engineering value
OFF, ON
OFF, ON
Engineering value
0 to 900 seconds (In increments of 1 second)
0 to 30
Engineering value
0.00 to 327.67%
1 to 32767min
1 to 32767min
1 to 32767min
White, Black
White, Black
No.1 to 10, Each provided with ch1 to 30
∗∗∗∗∗∗, ∗∗∗∗∗.∗, ∗∗∗∗.∗∗, ∗∗∗.∗∗∗, ∗∗.∗∗∗∗
OFF, ON
00:00 to 23:59
10, 20, 30 minutes, 1, 2, 3, 4, 6, 12 and 24 hours
Sunday to Saturday
1 to 31
00:00 to 23:59
Digital input, Channel alarm
Up to 32 characters
Up to 7 characters
Function invalid, Rec start/Rec stop, F value
calc. reset, Totalize start/stop, Totalize reset,
LCD ON
-32767 to 32767
0 to 255
0 to 255
0 to 255
OFF, ON
OFF, ON
OFF, ON
OFF, ON
OFF, ON
0 to 255
Up to 64 characters
Up to 32 characters
Up to 64 characters
None, DI ON, DI OFF,
Alarm ON, Alarm OFF, Warning, Timer cycle
Channel 1 to 30
1 to 4
Up to 32 characters
Up to 32 characters
OFF, ON
1 to 8
Up to 16 characters
Up to 8 characters
Administrator, Engineer, Operator, Guest
Password, Logon
0000 to 9999
0000 to 9999
8-5
Remarks
8.2 Outline of parameter setting procedure
Note) The outline of the setting screen is switched by settings of “Security mode” in Item 9.14.
If “Logon” is selected in the settings of “Security mode,” the outline of the setting screen
is also switched depending on the user level selected when logging on.
(1) Security mode : Password
Real time trend
display screen
Menu screen
(Note)
Parameter setting
Configration
password set
Parameter setting
menu screen
Basic setting
Basic setting screen
Channel setting
Channel setting screen
Channel setting copy
Channel setting
copy screen
Display setting
Display setting screen
F value calculation setting
F value calculation
setting screen
Totalize setting
Totalize setting screen
Message setting
Message setting screen
Original unit definition
Original unit
definition screen
DI function setting
DI function setting screen
Math channel setting
Math channel
setting screen
Math channel setting copy
Math channel setting
copy screen
Math timer setting
Math timer
setting screen
Constant setting
Constant
setting screen
Ethernet setting
Ethernet
setting screen
E-mail setting
E-mail
setting screen
E-mail trigger setting
E-mail trigger
setting screen
User account setting
User account
setting screen
Config and rec
password set
Configration password
set screen
Explanation of key
,
keys
Pressing these keys allow
you to shift menus one after
another on the “Parameter
Set” screen.
key
Pressing this key allows you
to confirm the menu item on
the “Parameter Set” screen.
*1
*3
key
After the setting, pressing
this key when registering
data or canceling data
registration returns to the
Menu screen.
key
Pressing this key in any
screen returns to the Real
time trend Display screen.
Important
*1) Parameter setting cannot
be changed while recording
is in progress.
*2) It is only used for calibration.
Don’t use it for other
purposes.
*3) Parameter setting cannot
be changed while
integration is in progress.
(Continued to the next page)
8-6
INP-TN2PHL-E
(Note)
CF manager and
Totalize exe.
CF manager
password set
CF manager and Totalize exe.
menu screen
Record data display
Record data
display screen
Memory card abstract
Memory card
abstract screen
Totalize control
Totalize control
screen
Totalize reset
screen
Totalize reset
Parameter file load
Parameter file
load screen
Parameter file save
Parameter file
save screen
CF manager
password set
CF manager
password set
screen
Version
Version display
screen
(Note)
Calibration password
Calibration password
Calibration menu screen
Input adjustment
*2
Input adjustment screen
Other function
(Note) In case the password has been set.
Parameter initialization
Adjust data initialization
(2)(a) Security mode : Logon,
Real time trend
display screen
INP-TN2PHL-E
Logon user : None
Menu screen
Logon/Logoff
Logon/Logoff screen
Version
Version display screen
8-7
Parameter initialization screen
(2)(b) Security mode : Logon,
Real time trend
display screen
Logon user : Administrator
Menu screen
Logon/Logoff
Logon/Logoff screen
Parametr setting
Parameter setting
menu screen
Basic setting
E-mail trigger setting
User account setting
Config and rec
password set
Menu screen is the same as
that of the case where
“Password” is selected in the
settings of “Security mode”
in Item 8.2 (1).
CF manager and Totalize exe.
menu screen
CF manager and
Totalize exe.
Menu screen is the same as
that of the case where
“Password” is selected in the
settings of “Security mode”
in Item 8.2 (1).
Version display screen
Version
Calibration password
Calibration menu screen
Calibration password
Menu screen is the same as
that of the case where
“Password” is selected in the
settings of “Security mode”
in Item 8.2 (1).
8-8
INP-TN2PHL-E
(2)(c) Security mode : Logon,
Real time trend
display screen
Logon user : Engineer
Menu screen
Logon/Logoff
Logon/Logoff screen
Parametr setting
Parameter setting
menu screen
Basic setting
E-mail trigger setting
Note: “User account setting” and
“Password set” screens are
not displayed.
CF manager and
Totalize exe.
CF manager and Totalize exe.
menu screen
Menu screen is the same as
that of the case where
“Password” is selected in the
settings of “Security mode”
in Item 8.2 (1).
Version
(2)(d) Security mode : Logon,
Real time trend
display screen
Version display screen
Logon user : Operator and Guest
Menu screen
Logon/Logoff
Logon/Logoff screen
CF manager and
Totalize exe.
CF manager and Totalize exe.
menu screen
Menu screen is the same as
that of the case where
“Password” is selected in the
settings of “Security mode”
in Item 8.2 (1).
Version
INP-TN2PHL-E
8-9
Version display screen
8.3 Basic operation of setting screens
The basic operation of the setting screens is classified in the following 3 methods. In this case, use the
up and down keys (▲ and ▼) to move setting items.
(1) Items to be selected with the ▲ or the ▼ key
Pressing the ▲ or the ▼ key switches the blinking between items.
Example: To change the input type from K-Type TC (K thermocouple) to E-Type TC
(E thermocouple)
Press the
8-10
key once.
INP-TN2PHL-E
(2) To make the setting by entering numeric values
Select a numerical value using the ▲, ▼, t or the s key and then press the
the entry.
Example: To select 10°C as the lowest temperature of the setting range
INP-TN2PHL-E
Press the
key three times.
Press the
key once.
8-11
key to confirm
(3) To make the setting by entering characters
Character entering field
Character display field
Select a position in the character entering field you want to enter a character by pressing the t or
the s key, and then press the
key.
Select a character in the character display field by pressing the t, s, ▲ or the ▼ key. The
selected character blinks. Then press the
key.
After entering characters in the character entering field, press the
key to confirm the entry.
Example: To enter PHL for group screen name
Press the
key twelve times.
(Move the cursor to “ENTRY” and then press the [ENT] key.)
8-12
INP-TN2PHL-E
9. SETTING PARAMETERS
9.1 Basic setting
[Explanation]
Follow the procedure shown below to make basic settings (including display refresh cycle, LCD lights
out time, MODBUS, and current time) of the recorder main unit.
[Operation]
Move the cursor to “Parameter setting” on the Menu screen and press the
setting screen appears. If the password has been set, enter the password.
Move the cursor to “Basic setting” and press the
key, the parrameter
key, the basic setting screen appears.
Display refresh cycle setting
Display compression setting
Alarm hysteresis setting
Alarm latch setting
LCD lights out time setting
DO setting at the time of memory FULL
DO setting at the time of battery END
File division cycle
File overwrite setting
Date display format setting
Language select setting
MODBUS communication station No. setting
MODBUS communication baud rate setting
MODBUS communication parity setting
Record data format setting
Current time setting
Register of data
INP-TN2PHL-E
9-1
(1) To set display refresh cycle
Move the cursor to “Refreshment cycle” and press the
below appears.
key, then the cycle time screen shown
(Cycle time: 1, 2, 3, 5, 10, 20, 30 seconds,1, 2, 3, 5, 10, 20, 30 minutes, 1, 2, 3, 4, 6, and 12 hours)
Relationship between “Refresh cycle” and “Chart speed” (on screen) is given below.
Refresh cycle
1 sec
2 sec
3 sec
5 sec
10 sec
Chart speed (as converted) 1296mm/h 648mm/h 432mm/h 260mm/h 130mm/h
Refresh cycle
Chart speed (as converted)
Refresh cycle
20 sec
30 sec
65mm/h
43mm/h
1 min
2 min
3 min
5 min
10 min
20 min
30 min
22mm/h
11mm/h
7.2mm/h
4.3mm/h
2.2mm/h
1.1mm/h
0.7mm/h
1 hour
2 hours
3 hours
4 hours
6 hours
12 hours
Chart speed (as converted) 0.36mm/h 0.18mm/h 0.12mm/h 0.09mm/h 0.06mm/h 0.03mm/h
The first time of the display update is started from 00:00:00 of the following without fail.
(Example)
When refresh cycle is set to 1 min, the next cycle begins at hh : mm : 0 (sec).
Note) If the refresh cycle time is short and a large number of recording files exist, the
recording at every refresh cycles may be skipped. Recording files should be
limited to 100 or less.
9-2
INP-TN2PHL-E
(2) To set display compression
Move the cursor to “Display compression” and press the
key to display the setting screen.
Select the compression ratio in the trend display, and press the
key.
For example, when the display update cycle is 1 second, the trend display is updated in the cycles
shown in the following table.
Compression ratio
Display time
1/1
1/10
1/30
1/60
1 sec
10 sec
30 sec
60 sec
(Note)
1. Compressed display cannot be made in the historical display screen.
2. Compression ratio cannot be changed while recording.
(3) To set the alarm output hysteresis width
key. The alarm hysteresis screen
Move the cursor to “Alarm hysteresis” and press the
appears (as shown below). Enter hysteresis width (0 to 100%) by the cursor key and then press
key for confirmation. It is applicable to all types of alarms. The numeric value is exthe
pressed as a percentage of the display range for each channel.
(4) To set alarm latch
key, then the alarm latch setting screen
Move the cursor to “Alarm latch” and press the
key.
appears. Make the setting using the cursor key and press the
Alarm latch function keeps alarm output turning on even after the cause of the alarm has been
removed. To cancel the alarm latch, select it to OFF. Alarm cancel is recorded in the event
summary in this case.
(5) To enter LCD lights out time
Move the cursor to “LCD-lights out time” and press the
setting screen appears.
key, then the LCD lights out time
Make the setting (0 to 60 minutes) using the cursor key and press the
The LCD is kept on at all times by entering 0 minute.
* Press any key to turn on the LCD.
INP-TN2PHL-E
9-3
key.
(6) To make DO setting at the time of memory FULL
key, then the DO output setting screen
Move the cursor to “Memory full alarm” and press the
key.
appears. Select desired DO output No. using the cursor key and press the
DO output works when memory FULL is detected. Select “None” not to use this function.
Note) DO11 to 28 are open collector outputs and not relay outputs.
Note) “Memory full alarm” is turned on when the remaining memory reaches 0%. This
value cannot be set.
Note) When memory card is removed, DO output turns off. But the message of memory
card full does not appear. Press the
or
key, it appears.
(7) To make DO setting at the time of battery END
key, then the DO output setting screen
Move the cursor to “Battery alarm” and press the
appears.
Select desired DO output No. using the cursor key and press the
key.
DO output functions when the battery END is detected. Select “None” not to use the function.
When battery END is detected, a message is displayed on the trend screen.
Note) DO11 to 28 are open collector outputs and not relay outputs.
(8) Setting the file division cycle
Move the cursor to “File division cycle” and then press the
key to display the File division
cycle setting screen.
If “No division” is selected, the archived file is not divided automatically.
If “1 hour,” “1 day” or “1 week” is selected, the archived file is divided hourly, daily or weekly
from the start of recording.
If “1 month” is selected, the archived file is divided at 0:00 on the first day of every month.
Note 1) If the “File division cycle” setting is shorter than the “Refreshment cycle” setting,
the archived file without data is created.
Note 2) If “1 hour,” “1 day” or “1 week” is selected as the file division cycle, the number of
data of the first file is one larger than that of the second and the subsequent files.
Note 3) Even if you select "No division" for the file division cycle setting, when the size of
recording file becomes 256MB or more, a new file is created automatically to continue recording.
If you select "1 week" or "1 month" for the file division cycle setting, when the size
of recording file becomes 256MB or more before the pre-set file division cycle, a new
file is created automatically to continue recording.
9-4
INP-TN2PHL-E
(9) Setting the file overwrite
Move the cursor to the “File overwrite” and press the
key for setting.
If the overwrite function in the archived file is turned ON, the oldest file is deleted and the new
record files are kept when the compact flash becomes full while recording.
The overwrite function on the archived file operates as follows.
• When the remaining capacity of compact flash is 1MB or less, the oldest file is deleted.
• The maximum number of record files is 1350 pieces. If the number of file exceeds 1350, the
oldest file is deleted regardless of the remaining capacity of flash memory.
• When the available capacity (the capacity of the deletable record file included) is lees than
10MB, the overwrite function in the archived file does not operate.
Note) The overwrite function in the archived file stops recording as in CF FULL in the same
state when the split function in the archived file is not operating, or when only one file
is kept in the compact flash even thought the split function is operating.
(10) Date display format setting
The display format of dates that appear on the data display screen can be selected.
On the Basic setting screen, move the cursor to “Date format” and then press the
display format select screen appears.
Move the cursor to the display format to be selected, and then press the
key, and the
key.
(11) Setting the language select
Move the cursor to “Language select” and press the
key to select a language.
When a language is switched to another, a language in the Web screen and E-mail is switched
accordingly.
(12) To select a station No. for MODBUS communication
Move the cursor to “MODBUS station No.” and press the
screen appears.
key, then the station No. setting
Select desired RS-485 MODBUS station No. (0 to 255) using the cursor key and press the
key. When set 0 to this parameter, communication does not work.
INP-TN2PHL-E
9-5
(13) To select baud rate for MODBUS communication
Move the cursor to “MODBUS baud rate” and press the
screen appears.
key, then the baud rate setting
Select desired RS-485 MODBUS communication baud rate (from 9600 and 19200 bps) using the
key.
cursor key and press the
(14) To select parity bit for MODBUS communication
Move the cursor to “MODBUS parity” and press the
appears.
key, then the parity bit setting screen
Select desired RS-485 MODBUS parity bit (from None, Odd and Even) using the cursor key and
press the
key.
(15) To select front communication setting (for loader)
Move the cursor to “Front communication” and press the
setting screen appears.
key, then the front communication
Select “ON” when this recorder is connected to a loader cable.
(16) To set record data format
Move the cursor to “Record data format” and press the
screen appears.
key, then the data format setting
Select either ASCII or Binary as data recording format.
Each format has the following characteristics.
ASCII format
• Allows the recorded data to be opened directly on Excel or using text editor.
• The number of data that can be recorded is relatively small (approximately 1/4 of those recorded
in binary format)
Binary format
• The recorded data cannot be opened directly on Excel or using text editor.
The recorded data can be opened using the attached data viewer software, and then by converting it to CSV file, it can be opened on Excel or the using text editor.
• The number of data that can be recorded is relatively large (approximately 4 times of those
recorded in ASCII format).
9-6
INP-TN2PHL-E
(17) To select time
Move the cursor to “Time setting” and press the
key, then the time setting screen appears.
Select desired time, year, month, hour and minute, using the cursor key and press the
key.
Reference 1: The clock is set to the current time of Japan Standard Time by the factory
at shipment.
Since it is backed-up by a lithium-ion battery, it is always running with
power interruption or power OFF. The lithium battery has a service life of
about 10 years at normal temperature of 25°C.
Reference 2: The time scale is divided into 24 hours. The range is set from 00: 00 to
23: 59.
Reference 3: A “second” is not settable. But, the inside of the clock is treated as follows.
After setting the “minute”, press the
key at the “Adjust” position. Then,
the clock runs with the second counter set to 0.
(18) Registering method of set values (saving to flash memory)
Move the cursor to “Register data” and press the
memory.
key, PHL registers the set value to the flash
Note 1) When the parameter memory lamp blinks in red, it indicates that set parameters
are not registered to the flash memory. Operate in accordance with above (16) to
register to flash memory.
Note 2) After parameters have been set, operate in accordance with above (16). Otherwise,
the set values returns to original values when turning OFF power.
INP-TN2PHL-E
9-7
9.2 Channel settings
[Explanation]
Follow the procedure shown below to select input type, unit, scaling, input filter (time constant),
PV shift, PV gain, subtraction, F value calculation, color, TAG No., recording type, recording mode,
totalizing setting and alarm setting for each channel.
[Operation]
Move the cursor to “Parameter setting” on the Menu screen and press the
has been set, enter the password, and the parameter setting screen appears.
Move the cursor to “Channel setting” and press the
key. If the password
key, then channel setting screen appears.
On this screen, select desired channel number and press the
key. Following screen appears.
Input type setting
TAG No. setting
Scaling setting
Unit setting
Measurement range setting
Decimal point position setting
Engineering value setting
Square root calculation setting
Logarithmic display
Display range setting
Input filter setting
Subtraction channel setting
PV shift value setting
PV gain setting
F value calculation function setting
Display color setting
Recording type setting
Recording mode setting
Totalizing setting
Alarm setting
9-8
INP-TN2PHL-E
(1) To set input type
Move the cursor to “Input type” and press the
key, then the following input type selection
screen appears. Select any input signal by using the cursor key and press the
key. If you
don’t want to perform “indication”, “recording”, and “alarm” operation, select “Skip”.
Note 1) When the “Input type” is set to “Skip”, indication, recording and alarm for the
channel are not carried out.
Note 2) After the change of the “Input type”, wait for a while until the measured value
stabilizes.
Note 3) When the recorder is in recording, the “Input type” cannot be changed.
Note) About input type setting
Basically, the input type can be every 2 channels.
The input type of channel 2, 4, 6, 8, 11, 13, 15 and 17 can only be set in the same category of
previous channel.
If “Skip” has been selected for the previous channel, arbitrary input type can be selected.
The following input types are available.
Input type
Details
Thermocouple, 50mV
K, E, J, T, R, S, B, N, W, L, U, and PN thermocouples, 50mV
Resistance bulb
500mV
5V
Pt100, JPt100, Ni100, Pt50, Cu50
500mV
1 to 5V, 0 to 5V
Note, however, that arbitrary input type can be selected only for channels 9 and 18 irrespective
of the type allocated to other channels. For example, if the input type 1 to 5V is selected for
channel 1, the following screen appears as the input type selection screen for channel 2, which
allows only1 to 5V, 0 to 5V, or Skip to be selected.
INP-TN2PHL-E
9-9
The sample of input type setting
Input type
Channel 1
K thermocouple
Channel 2
T thermocouple
Channel 3
1 to 5V
Channel 4
0 to 5V
Channel 5
Pt100
Channel 6
JPt100
Channel 7
500mV
Channel 8
500mV
Input type
Description
Thermocouple, 50mV
The type of thermocouple can be arbitrarily selected
for each channel.
5V
Resistance bulb
The type of resistance bulb can be arbitrarily selected
for each channel.
500mV
Channel 9
J thermocouple
Thermocouple, 50mV
Input type can be arbitrarily selected for channel 9.
Channel 10
K thermocouple
Thermocouple, 50mV
Channel 11
50mV
The input type of the thermocouple and 50mV is the
same.
Channel 12
Skip
5V
Channel 13
1 to 5V
Skip can arbitrarily selected irrespective of the input
type.
Channel 14
Pt100
Channel 15
Skip
Channel 16
Skip
Channel 17
500mV
Channel 18
50mV
Resistance bulb
500mV
Thermocouple, 50mV
9-10
Input type can be arbitrarily selected for channel 18.
INP-TN2PHL-E
(2) To set TAG 1 and TAG 2
• TAG 1
Move the cursor to “Tag 1” and press the
key, then “TAG Setting” screen appears as shown
key for confirmation.
below. Enter the TAG name by using the cursor key and press the
key to register the data.
After entry of the TAG name, press the
Up to 8 characters can be entered. Note, however, that on some screens such as trend screen, only
7 characters can be displayed.
• TAG 2
Tag 2 is displayed on the screen for 4 channels.
To display at the TAG display area on trend display screen is selectable by parameter, “Channel
index”.
Regarding to setting method, refer to 9.6 (7), “To select channel index”.
(3) To set scaling
With DC voltage input, set scaling “ON” “OFF” with the cursor key.
Note) When scaling is set to “ON”, the recording range is zero-cleared. For details, refer to
Item 9.2 (9) “To set display range”.
(4) To set units
Units can only be set when the scaling is set to “ON”.
key, then “Unit menu” screen (below) appears.
Move the cursor to “Unit” and press the
Select any unit on the screen by using the cursor key, and press the
key.
Unit select screen varies depending on the input type. (The following figure is the case of DC
voltage input.)
INP-TN2PHL-E
9-11
Unit code
Temperature
· humidity
Pressure
Flow rate
°C
t/d
t/h
t/min
t/s
°F
kg/d
kg/h
kg/min
kg/s
MPa
mm
ml
mm2
bar
Pa
cm
l
cm2
kPa
m
%RH
g/d
g/h
g/min
g/s
vol%
m3/d
m3/h
m3/min
m3/s
N/m2
l/d
l/h
l/min
l/s
Analysis
g/cm3
g/l
ppm
ppmNOx
%CO2
Capacity ·
Weight · Area
mPa
mbar
N/mm2
Density
Level·
Height
kl
m2
mm3
g
cm3
kg
m3
t
Power ·
Acceleration
mN
mm/s
rps
µs
Time
Electromagnetism
mV
kg/cm3
kg/l
ppmNH3
ppb
%He
N
mm/min
rpm
ms
V
g/m3
g/ml
ppmSO2
pH
%Ar
N·m
mm/h
rph
s
kV
ppmH2S
mol
%O2
J
m/s
m/s2
min
µA
ppmCO
%
%NaCl
kJ
m/min
rad/s
h
mA
ppmO2
%H2
%CO
m/h
km/h
day
A
kg/m3
Electromagnetism
Heat · Light Radiation
Other
Customer-made
(Note 2)
Hz
Var
mH
lx
µSv/h
Pa · s
(Unit 1)
(Unit 7)
dB
kVar
H
cd
mSv/h
mPa · s
(Unit 2)
(Unit 8)
W
µS/cm
m ohm
lm
nGy/h
(Unit 3)
(Unit 9)
kW
µF
ohm
cd/m2
µGy/h
(Unit 4)
(Unit 10)
VA
F
k ohm
µm
(Unit 5)
(Unit 11)
kVA
C
M ohm
(Unit 6)
(Unit 12)
Note 1) Blank consists of some spaces
Note 2) Units can be made by the customer (See Item 9.10).
(5) To enter the measuring range
The measuring range can be set only when the scaling is set to ON at voltage input type.
To display the measuring range setting screen, move the each cursor to “Measuring range” and
press the
key. By using the cursor key and press the
key for confirmation.
9-12
INP-TN2PHL-E
(6) To set the decimal point position
Decimal point position can be set only when scaling is set to ON at voltage input type.
key, then the following decimal point
Move the cursor to “Decimal point” and press the
position setting screen appears. Select desired decimal point position using the cursor key and
press the
key for confirmation.
(7) To enter the engineering unit
The engineering unit can be set only when the scaling is set to ON at voltage input type.
To display the engineering unit setting screen, move the cursor to “Engineering unit” and press
key. By using the cursor key and press the
key for confirmation.
the
(8) To enter square rooter (rooter)
Square rooter “ON” and “OFF” can be set by using the cursor key in the case of DC voltage input.
Description of square rooter
The measuring range is set to 0 to 100%. For example, in case of DC1 to 5V input, 1V is 0% and 5V
is 100%, and square rooter is performed against this percentage value. Refer to example below.
If the input value converted to percentage is minus, the result of square rooter should be 0%.
The data after the square rooter (0 to 100%) is converted to industrial value with the obtained data
regarded as 0 to 100% of the engineering unit.
Example: In the case of the following input setting, the readings for the input values are as
follows:
Input type: 1 to 5V
Measuring range:1 to 5V
Industrial value: 0 to 1000 (t/h)
When input is 1V (0%)
When input is 3V (50%)
When input is 5V (100%)
When input is 0.6V (-10%)
INP-TN2PHL-E
9-13
Reading
(1000-0) × √–0 = 0 (t/h)
(1000-0) × √–0.5 = 707 (t/h)
(1000-0) × √–1 = 1000 (t/h)
(1000-0) × √–-0.1 → 0 (t/h)
(9) Logarithmic display
The settings specified in this section can be performed only when the scaling setting of the DC
voltage input is set to ON.
Select “ON” or “OFF” for the logarithmic display with the cursor key.
Note) When the logarithmic display is set to ON, the following functions are performed.
• Only the exponent part of the engineering unit and the display range can be set. The setting
range is –9 to 9 (10–9 to 109).
• The subtraction, F value calculation, and totalizing of the measured values cannot be performed.
• The PV shift value is set as a voltage value.
• The record data is recorded as a voltage value.
Details of the logarithmic display function
The logarithmic display of the measured voltage in the range from 1.00E–9 to 1.00E+9 can be
performed.
Only the exponent part of the engineering unit and the display range can be set.
Example) The table below shows the indicated values for the input values under the condition
that the following settings are performed.
Input type: 1-5 V
Measuring range: 1 to 5 V
Engineering unit: 1 to 5 (which means 1.00E+1 to 1.00E+5.)
Indicated value
When the input value is 1 V
1.00E+1
When the input value is 3 V
1.00E+3
When the input value is 5 V
1.00E+5
(10) To set display range
key, then, the “Range setting” screen
Move the each cursor to “Display range” and press the
key for confirmaappears as shown below. Enter the range by the cursor key, and press the
tion.
For the setting range, refer to Table 1, “Display Range Set Range”.
<in case of input type is thermocouple or Pt>
<in case of input type is voltage input>
9-14
INP-TN2PHL-E
Table 1 Display Range Set Range
Input range
Type
Thermocouple
B
R
S
K
E
J
T
N
W
L
U
PN
Resistance
bulb
JPt100
Pt100
Ni100
Pt50
Cu50
Record range set range
400 to 1760°C
0 to 1760°C
0 to 1760°C
–200 to 1370°C
–200 to 800°C
–200 to 1100°C
–200 to 400°C
0 to 1300°C
0 to 1760°C
–200 to 900°C
–200 to 400°C
0 to 1300°C
370.0 to 1790.0°C
– 30.0 to 1790.0°C
– 30.0 to 1790.0°C
–230.0 to 1400.0°C
–230.0 to 830.0°C
–230.0 to 1130.0°C
–230.0 to 430.0°C
– 30.0 to 1330.0°C
– 30.0 to 1790.0°C
–230.0 to 930.0°C
–230.0 to 430.0°C
– 30.0 to 1330.0°C
–200 to
–200 to
–60 to
–200 to
–50 to
–230.0 to
–230.0 to
–90.0 to
–230.0 to
–80.0 to
DC voltage
600°C
600°C
180°C
600°C
200°C
–
–
+
–
0 to + 50mV
0 to +500mV
+ 1 to + 5V
0 to + 5V
(11) To set input filter (primary delay filter)
Move the cursor to “Input filter” and press the
numerical values by using the cursor key.
630.0°C
630.0°C
210.0°C
630.0°C
230.0°C
10.00 to +
10.0 to +
0.500 to +
0.100 to +
55.00mV
550.0mV
5.500V
5.500V
key, then small window appears. Select
Input filter range: 0 to 900 sec (step of 1 sec)
(12) To select subtraction channel
key, then small window appears. Select
Move the cursor to “Subtract channel” and press the
the channel No. for which subtraction is to be performed using the cursor.
[Subtraction function]
• The result of subtraction of the values for 2 channels is recorded to the channel to be set.
Example: When the result of ch1-ch2 is recorded to ch1
ch1=ch1-ch2
• Be sure to perform subtraction between the channels having the same unit and decimal point position. Otherwise the record cannot be guaranteed.
• Subtraction is not performed when “none” is selected.
• Limit doesn’t work for the result of subtraction.
INP-TN2PHL-E
9-15
(13) To set PV shift value
Move the cursor to “PV shift” and press the
below.
key, then “PV shift” screen appears as shown
Enter PV shift value by using the cursor key and press the
key.
[PV shift function]
• Measured values can be calculated, recorded, and displayed with the PV shift constant.
• PV shift calculation can be achieved with the gain and shift values.
Conversion graphs relating to shift calculation and gain calculation are shown below.
• Shift calculation
Shift setting = 10
Recorded and
displayed value
Shift setting of 0
(Measured
values after
PV calculation)
Measured values
• Gain calculation
Gain setting = 110%
Recorded and
displayed value
Gain setting of 100%
(Measured
values after
PV calculation)
Measured values
• PV shift is calculated as follows;
P’ = AP + B
Where,
P’: Measured value after calculation of PV shift
P : Measured value
A : Gain (0.00 to 327.67%)
B : Shift values (setting range: –32767 to 32767 engineering unit, decimal point
depends on input type)
* The measured value after PV shift calculation is limited so that it falls within the settable
record range by input type set for each channel. The judgement of input error (such as
Burnout, Error, and Over) is performed against the input and not for the result of shift or gain
calculation.
• If input type is changed or the scaling function is turned ON/OFF, the PV shift set value for the
channel is cleared. (If the scaling function is turned ON/OFF by the setting copying function, the PV
shift set value for the channel is not cleared.)
• The Copy function allows you to copy set values, but it is not provided with a means of making copy
of PV shift set values.
9-16
INP-TN2PHL-E
(14) To set PV gain
Move the cursor to “PV gain” and press the
below.
key, then the “PV gain” screen appears as shown
Enter PV inclination by using the cursor key and press the
key.
(15) F value calculation function
Select F value calculation “ON” or “OFF” using the cursor.
Note that if “ON” is selected, calculation is performed according to the selection made in Item 9.7
“Setting method of F value calculation.”
[F value calculation function]
From the measured temperature, the extinction value of bacteria by sterilization by heating can be
calculated.
F value calculation formula
(T – T0)
F value =
10 Z
60
T : Measured temperature
T0 : Reference temperature
Z : Z value
• F value calculation is performed by the second.
• The measured temperature of the channel for which F value calculation is performed cannot be
recorded.
• The unit field of the channel for which F value calculation is performed is kept blank, and the
decimal place is set to the one designated in F value calculation setting screen that is common to
all channels.
• The constants to be used for F value calculation (reference temperature, Z value, and decimal
point position) are common to all channels.
• F value calculation can be reset manually or by DI or temperature setting.
• If input is abnormal, an error (such as Over, Under, Burnout, Error) is displayed, but 0 is recorded.
INP-TN2PHL-E
9-17
(16) To set display color
key, then the following color selection window
Move the cursor to “Color” and press the
key.
appears. Select the display color using the cursor and press the
(17) To set recording type
key, then the following recording type
Move the cursor to “Recording type” and press the
selection screen appears. Select a desired recording type using the cursor key, and then press the
key.
[About recording type]
Recording type can be selected from the following three.
• Point value recording: Records the instantaneous measurement value at every display refresh
cycle.
• Average value recording: Records the average measurement value during the display refresh
cycle at every display refresh cycle.
• Maximum/minimum recording: Records the maximum/minimum measurement value during the
display refresh cycle at every display refresh cycle.
* Longer recording is allowed with instantaneous and average value recording than with maximum/minimum value recording.
(18) To set recording mode
key, then recording mode screen apMove the cursor to “Recording mode” and press the
pears.
Select either “With record” or “Display only” by the cursor.
When setting “Display only”, trend display on the Trend screen and history display on the Historical screen are not carried out. Further, nothing is recorded except for display of measured values.
9-18
INP-TN2PHL-E
(19) Totalize setting
Move the cursor to “Totalize setting” and press the
screen appears.
key, then the following totalizing setting
Select the item to be set using the cursor key and then press the
key.
Totalize tag setting
Totalize calculation setting
Totalize data unit setting
Totalize cut value setting
Totalize scaling value setting
Totalize reset input
(a) To set totalize tag
key, then the following character entry
Move the cursor to “Totalize tag” and by press the
key. When entry is
screen appears. Enter the tag name by using the cursor key and press the
key to register the entry.
completed, press the
• Totalize tag is recorded in totalize recording result and displayed on the totalize display screen.
INP-TN2PHL-E
9-19
(b) To set totalize calculation
Either “Totalizer,” “Counter,” or “Timer” can be selected as “Totalize calculation.”
Note) When the logarichmic display setting is ON, do not select “Totalizer”.
a) Select “Totalizer” to perform totalize function of creating daily and monthly reports.
b) Select “Counter” to record the number of times of DI ON or alarm ON during the totalize
period. The value to the right of decimal point is discarded.
c) Select “Timer” to record the duration of DI ON or alarm ON during the totalize period.
In all of the above cases, time is displayed based on the time set in a parameter, “Totalize
base time,” with all digits to the right of the decimal point discarded.
Example: When the following parameters are selected, data is recorded as shown below.
Totalize base time = /min
Totalize type
= Dairy
Digital input
= Di2
ON
ON
Di1
OFF
OFF
OFF
ON
ON
Di2
OFF
OFF
OFF
Totalize start
20
30
40
50
10
Totalize calculation = Counter
= Timer
1
0
1
10
Recorded data
2
2
10
20
2
30
60
Elapsed time [min]
2
30
[min]
* Since Digital input is Di2 in this example, it is independent of the on/off operation of Di1.
(c) To set totalize type
Select one from daily report, weekly report, monthly report, annual report, continuous totalizing,
and daily report (at designated time) in “Totalize type.” Refer to the following table for the
totalize operation of each selection.
Periodic report
Totalized value is recorded (and reset) at every totalize cycle that has been set.
The totalize cycle is from one totalize base time to another.
Daily report
Totalized value is recorded (and reset) at totalize base time every day.
Weekly report
Totalized value is recorded (and reset) weekly at totalize base time of the specified
day of the week.
Monthly report
Totalized value is recorded (and reset) monthly at totalize base time of the specified
day of the month.
Annual report
Totalized value is recorded (and reset) annually at totalize base time on January 1st.
Daily report
(at designated time)
Totalizing is performed from the start time to the stop time every day, and on completion
of the operation, totalized value is recorded (and reset).
External input
Totalize operation is performed during the period from the external input is turned on to
it is turned off. Totalized value is recorded (and reset) when it is turned off.
(Totalize calculation is not reset even if the power is turned off.)
(d) To set digital input
• Use DI input for totalizing when “Counter” or “Timer” is specified for totalize calculation.
9-20
INP-TN2PHL-E
(e) To set totalize base time
• Totalize base time can be selected from /s, /min, /h, and /day.
Example: If the flow rate is 120L/min, totalized value for each totalize base time appears as follows.
Base time
/s
/min
/h
/day
Totalized value
2
120
7,200
172,800
* Flow rate of 120L/min is also expressed as 2L/s (120/60), or 7,200L/h (120×60).
(f) To set reset operation
• If “Reset Operation” setting is ON, totalize data is recorded in the totalize file at every totalize
cycle.
• If “Reset Operation” setting is OFF, sum total data from the start of totalizing is recorded in the
totalize file.
Example: If the flow rate is 100L/h, the record data appears as follows.
Totalize reset
Elapsed time
OFF
ON
1 hour
100
100
2 hours
200
100
3 hours
300
100
(g) To set totalize unit
key to display the following unit select
Move the cursor to “Totalize unit” and press the
screen. Select the desired unit using the cursor key and then press the
key.
INP-TN2PHL-E
9-21
(h) To set totalize cut value
Move the cursor to “Totalize cut value” and press the
key to display the following totalize
cut value setting screen. Enter totalizing cut value using the cursor and the
key.
• If the measured value is smaller than the totalizing cut value, the measured value is regarded as
0 in the totalizing (totalizing value does not increase).
(i) To set totalize scale value
Move the cursor to “Totalize scale value” and press the
scaling setting screen appears.
Enter the scaling value using the cursor key and press the
key, and the following totalize
key.
• Specify as “Totalize scale value” the scale conversion value used to convert the input value to
totalized value. Division only is allowed. Multiplication cannot be performed.
Totalize value = Analog input/Totalize scale value
Example: To convert the unit of input value (L/h) to [m3/h],
1 [L/h] =1/1000 [m3/h]
Totalize scale value = 1000
(j) To set totalize reset input
Totalize reset input can be selected from “None”, “Digital input”, “Channel alarm”.
9-22
INP-TN2PHL-E
(20) To set alarms
Move the cursor to “Alarm setting” and press the
appears.
key, then following alarm setting screen
Select a desired item by using the cursor key, and then press the
key.
Alarms can be set up to 4 points per channel. (Alarm No. 1 to 4)
Alarm operation type setting
Alarm point setting
Alarm unit relay No. setting
Alarm No. 1
Alarm No. 2
Alarm No. 3
Alarm No. 4
(a) To set the type of alarm operation
Select from alarm types H and L by using the cursor key.
• Two alarm levels, H and L (H or L can be arbitrarily selected for each alarm.)
Select OFF to stop the alarm operation.
(b) To set alarm DO relay No.
Select alarm DO relay No. by using the cursor key.
In case of the 11th digits of Model code is “1”
• Select optional alarm unit relay No. 1 to 10. If not necessary, select “None” for no output.
These outputs are relay (SPST).
In case of the 12th digits of Model code is “R”
• Select optional alarm unit relay No. 11 to 28. If not necessary, select “None” for no output.
These outputs are open collector. (Rate: 30Vdc, 0.1A)
(c) To set alarm set point
key, and the following alarm setting
Move the cursor to “Alarm set point” and press the
key.
screen appears. Enter desired alarm set point using the cursor key and the
• Make the setting using engineering values (absolute value alarm).
Note) • When logarithmic display is ON, the alarm set point may not be the same as one set in
the alarm setting screen.
• When logarithmic display is ON, the alarm set point changes if the measuring setting and
engineering setting are changed.
INP-TN2PHL-E
9-23
9.3 Copying parameters
[Explanation]
Parameters can be copied to other channels.
Parameters that can be copied are input type, input filter, scaling, recording range, unit, TAG No.,
alarm setting, and subtraction channel.
[Operation]
Select the “parameter setting” on the menu screen and enter the password if the configuration password has been set, then select “Channel setting copy”. After that, following “channel setting copy”
screen appears.
Copy screen used when the number of input points is 9
Channel No. to copy from
Channel No. to paste to
When parameters are pasted to
all channels
Copy start button
(1) Channel No. to copy from
Select a channel No. from which parameters are to be copied using the cursor key. Then press
the
key, and following channel selection screen appears.
(2) Channel No. to paste to
Select the channel No. to which parameters are to be pasted using the cursor key and press the
key. If you want to cancel, press the
key.
(When you want to paste to all the channels, select “All channels.”)
9-24
INP-TN2PHL-E
(3) Copy start button
Move the cursor to “Copy start” by using the cursor key and press the
screen as shown next page appears.
Press the
key to copy, and press the
key to cancel.
Guidance screen for the number of input points of 9
INP-TN2PHL-E
9-25
key, then the guidance
9.4 Setting calculation function
[Explanation]
Twelve channels from Channel 19 to 30 can be used as calculation channels.
(a) Three operations × 4 formulas can be set for each channel.
The result of Formula 4 is input to the operation channel.
The result of operation is limited to ±32767 with all digits to the right of the decimal point discarded.
(b) Note 1: Arithmetic operations are performed from left to right without fail.
Example: Formula 1, B01 = C01 + C02 × C03, is calculated as B01 = (C01 + C02) × C03.
Note 2: AVG(A) and SUM(A,B) can be used only once for each channel.
Note 3: It takes a long time to perform many arithmetic operations, and consequently the display
cycle of measurement may become long.
Refer to the following table for the functions used for calculation.
Operation
Grammar
Description
Arithmetic operation (addition)
A+B
Adds the value of input A and input B.
Arithmetic operation
(subtraction)
A-B
Subtracts the value of input B from input A.
Arithmetic operation
(multiplication)
A B
Multiplies the value of input A by input B.
Arithmetic operation (division)
A/B
Division the value of input A by input B.
Note: The result of calculation of 0/0 is 0.
Absolute value
ABS(A)
Finds the absolute value of input A.
Power
POW(A,B)
Finds the value of input A to the power input B. (A
Square root
SQR(A)
Finds the square root of the value of input A.
LOG
LOG(A)
Finds the common logarithm of the value of input A.
LN
LN(A)
Finds the natural logarithm of the value of input A.
EXP
EXP(A)
Finds the exponentiation of the value of input A with base “e.”
Humidity
RH(A,B)
Finds the relative humidity when input A represents dry-bulb
temperature and input B represents wet-bulb temperature.
B)
Maximum (between channels)
MAX(A,B)
Finds the maximum value from inputs A and B.
Minimum (between channels)
MIN(A,B)
Finds the minimum value from inputs A and B.
Maximum (time)
H-P(A)
Finds the maximum value of input A.
Initializes the maximum value by timer input.
Minimum (time)
L-P(A)
Finds the minimum value of input A.
Initializes the minimum value by timer input.
Average
AVG(A)
Finds the average value of input A.
Refreshes the average value by timer input.
Summatio
SUM(A,B)
Finds the sum of input A/B.
Resets the sum by timer input
Clear the formula
END/Delete
Clear the formula without confirming.
Be careful not to missoperate. You can’t cancel this operation.
Set the soarce
Math data
Set the sorce from “Input channel”, “Totalizer input”,
“Digital input”, “Communication input”, “Constant” or
“Temporary formula”.
9-26
INP-TN2PHL-E
(c) The input point that can be used for calculation are as follows.
Input
Grammar
Description
Input channel
C01 to C30
Channel 1 to 30 input
Totalize input
T01 to T30
Channel 1 to 30 totalize (The totalized value limited to ±32767
with all digits to the right of the decimal point discarded is used.)
Digital input
D01 to D10
DI1 to 10 (OFF: 0, ON: 1)
Communicationn input
M01 to M12
1 to 12 (No decimal fraction allowed.)
Constant
K01 to K20
1 to 20
Temporary formula
B01 to B03
1 to 3
Detailed description of functions
ABS(A)
: Finds the absolute value of input A
Example of output of ABS(A) is shown below. (The decimal place of operation channel is 1.)
Input
A
Output
ABS (A)
Memo
10.0
10.0
-10.0
10.0
POW(A,B) : Finds the value of input A to the power input B. (A**B)
If negative fractional value is raised to the power of a fractional value, 0 is output.
The result of 0 raised to the power of 0 is 1.00
Example of output of POW(A) is shown below. (The decimal place of operation channel is 1.)
Input
A
SQR(A)
Output
POW (A, B)
Input
B
Memo
50.0
2.0
-5.5
2.5
0.0 When erroneous data is input.
0.0
0.0
1.0 The result of 0 raised to the 0th
power is 1.
2500.0
: Finds the square root of the value of input A.
If negative data is input, 0 is output.
Example of output of SQR(A) is shown below. (The decimal place of operation channel is 1.)
Input
A
Output
SQR (A)
100.0
10.0
-10.0
LOG(A)
Memo
0.0 If negative data is input, 0 is output.
: Finds the common logarithm of the value of input A.
If negative data is input, 0 is output.
Example of output of LOG(A) is shown below. (The decimal place of operation channel is 1.)
Input
A
INP-TN2PHL-E
Output
LOG (A)
Memo
100.0
2.0
-10.0
0.0 If negative data is input, 0 is output.
9-27
LN(A)
: Finds the natural logarithm of the value of input A.
If negative data is input, 0 is output.
Example of output of LN(A) is shown below. (The decimal place of operation channel is 1.)
Input
A
EXP(A)
Output
LN (A)
Memo
100.0
4.6
-10.0
0.0 If negative data is input, 0 is output.
: Finds the exponentiation of the value of input A with base “e”. (e**A)
Example of output of EXP(A) is shown below. (The decimal place of operation channel is 1.)
Input
A
Output
EXP (A)
1.2
RH(A,B)
Memo
3.3
: Finds the relative humidity when input A represents dry-bulb temperature and input
B represents wet-bulb temperature.
The temperature range that allows the calculation of humidity is from -40 to +150°C.
If the wet-bulb temperature is equal to or higher than the dry-bulb temperature, 100%RH is
output.
If the temperature is outside the measurable range, the values in the following table are
output.
Wet-bulb temperature
Lower than -40°C
Dry-bulb
temperature
Within the range
Higher than +150°C
Lower than -40°C
0%RH
0%RH
0%RH
Within the range
0%RH
Calculated value
100%RH
Higher than +150°C
0%RH
100%RH
100%RH
Example of output of RH(A,B) is shown below. (The decimal place of operation channel is 1.)
Input A
Output
Input B
(Dry-bulb
RH (A, B)
(Wet-bulb
temperature) temperature)
MAX(A,B)
Memo
70.0
65.0
70.5
70.0
50.0
-41.0
0.0 Input B < -40°C
151.0
10.0
100.0 Input A > 150°C
79.2
100.0 100%RH is output if input A = Input B.
: Finds the maximum value from inputs A and B.
Example of output of MAX(A,B) is shown below. (The decimal place of operation channel is 1.)
Input
A
Output
MAX (A, B)
Input
B
Memo
50.0
49.0
50.0 Input A > Input B
49.0
50.0
50.0 Input A < Input B
9-28
INP-TN2PHL-E
MIN(A,B)
: Finds the minimum value from inputs A and B.
Example of output of MIM(A,B) is shown below. (The decimal place of operation channel is 1.)
Input
A
H-P(A)
Output
MIN (A, B)
Input
B
Memo
50.0
49.0
49.0 Input A > Input B
49.0
50.0
49.0 Input A < Input B
: Finds the maximum value of input A.
The output is initialized in a cycle established as H-P, L-P timer cycle.
Example of output of H-P(A) is shown below. (The decimal place of operation channel is 1, and H-P,
L-P timer cycle is 2 minutes.)
Input A
Output H-P(A)
(Output value per cycle)
Sine wave cycle: 1 minute,
Amplitude: 50.0, Bias: 0.0
L-P(A)
Memo
50.0 Maximum sine wave value
: Finds the minimum value of input A.
The output is initialized in a cycle established as H-P, L-P timer cycle.
Example of output of L-P(A) is shown below. (The decimal place of operation channel is 1, and H-P,
L-P timer cycle is 2 minutes.)
Input A
Output L-P(A)
(Output value per cycle)
Sine wave cycle: 1 minute,
Amplitude: 50.0, Bias: 0.0
AVG(A)
Memo
-50.0 Minimum sine wave value
: Finds the average value of input A.
The average value during the cycle established as AVG timer cycle is output.
(Display is not changed during the cycle.)
Example of output of AVG(A) is shown below. (The decimal place of operation channel is 1, and the
AVG timer cycle is 2 minutes.)
Input A
Output AVG(A)
(Output value per cycle)
Sine wave cycle: 1 minute,
Amplitude: 50.0, Bias: 0.0
SUM(A)
Memo
0.0 Average sine wave value
: Finds the sum of input A/B.
The totalized value is reset in the cycle established as the SUM timer cycle.
Negative values can also be totalized.
Example of output of SUM(A) is shown below. (The decimal place of operation channel is 1, and the
SUM timer cycle is 2 minutes.
Input A
(Fixed)
50.0
INP-TN2PHL-E
Output
SUM (A, B)
Input B
(Fixed)
120.0
50.0
50.0
60.0
100.0
-50.0
120.0
-50.0
9-29
Memo
[Operation]
Select the “parameter setting” on the menu screen and enter the password if the configuration password has been set, then select “Math channel setting” and desired channel number. After that, following channel number setting screen appears. Press the
key.
Formula setting
Tag No. setting
Unit setting
Measurement range setting
Decimal point position setting
Engineering value setting
Square root calculation setting
Logarithmic display
Display range setting
Input filter setting
Subtraction channel setting
PV shift value setting
PV gain setting
F value calculation function setting
Display color setting
Recording type setting
Recording mode setting
Totalizing setting
Alarm setting
(1) Formula setting
Move the cursor to “Formula setting” and press the
screen appears.
9-30
key, and the following formula setting
INP-TN2PHL-E
Move the cursor to the formula you want to make the setting and press the
following formula setting screen appears.
key, and the
Note: The result of Formula 4 is output to the operation channel.
Press the
key once again, and the following function selection screen appears.
Move the cursor to the function you want to use and press the
data type selection screen appears.
Move the cursor to the input type you want to use and press the
selection screen that appears, select an input type you want to use.
Press the
key, and the following input
key. On the input type
key, and the formula setting screen appears again.
To set the next operation, move the cursor to the right using the > key, and make the setting in the
same manner.
To delete a formula, select “End/Delete.”
(2) TAG. No. setting and subsequent settings
For the setting procedures from Tag No. to alarm setting, refer to Item 9.2 (2).
INP-TN2PHL-E
9-31
9.5 Setting timer for calculation
[Explanation]
Only when the use of timer is specified when formula is selected in Item 9.4 “Calculation function,”
follow procedure shown below.
[Operation]
Select the “parameter setting” on the menu screen and enter the password if the configuration password has been set, then select “Math timer setting”.
After that, following “Math timer setting” screen appears.
H-P, L-P timer cycle setting
AVG timer cycle setting
SUM timer cycle setting
(1) H-P, L-P timer cycle setting
Move the cursor to “H-P, L-P timer cycle” and press the
cycle setting screen appears.
Enter cycle time using the cursor key and press the
9-32
key, then the following operation
key.
INP-TN2PHL-E
(2) AVG timer cycle setting
Move the cursor to “AVG timer cycle” and press the
setting screen appears.
Enter cycle time using the cursor key and press the
(3) SUM timer cycle setting
Move the cursor to “SUM timer cycle” and press the
setting screen appears.
Enter cycle time using the cursor key and press the
INP-TN2PHL-E
9-33
key, then the following operation cycle
key.
key, then the following operation cycle
key.
9.6 Setting for data display screen
Four combinations of the input channels you want to display (called screen structure or group screen)
can be set on the data display screen.
In addition, background color on the real-time trend screen and the historical trend screen can be set.
9.6.1 Display screen setting
[Explanation]
• Background color on the real-time trend and historical trend screens is set.
[Operation]
On the “Menu” screen, select “Parameter setting” → “Display setting” → “Display screen setting”.
(1) To set trend back color
Move the cursor to the “Trend back color” and press the [ENT] key to select a background color
in the real time trend screen. White or black color can be selected.
(2) To set historical back color
Move the cursor to the “Historical back color” and press the [ENT] key to select a background
color in the historical trend screen. White or black color can be selected.
9-34
INP-TN2PHL-E
9.6.2 Display group setting
[Explanation]
• Set the name of group screen using alphanumerical characters. Up to 16 characters can be entered.
• Set the screen structure (group screen) on the data display screen.
[Operation]
Select the “parameter setting” on the menu screen and enter the password if the configuration password has been set, then select “Display setting” and desired display group number.
After that, following display group setting screen appears.
Select group screen No.
Select screen name.
Select group structure.
Select trend direction.
Select the number of screen split.
Select trend screen scale display.
Select graph display.
Select color bar display.
• Set the group construction.
• Select the direction (vertical or horizontal) of the trend screen (real time trend screen and historical
trend screen).
• Select the number of screen division.
• Select ON/OFF of the trend screen scale display.
• Select bar graph or analog meter as a measurement display method.
• Select one from Tag No. display, unit display or channel No. display as display contents of the color
bar.
• If a group has less than 4 channels, the real time trend display, etc. automatically switch to the screen
for 4-channel display.
INP-TN2PHL-E
9-35
(1) To set display name
key, then the following character entering
Move the cursor to “Display name” and press the
key.
screen appears. Enter the display name using the cursor and press the
When the name is entered, press the
key to register the screen name.
(2) To set display structure
Move the cursor to the channel No. you want to make setting change on the display group setting
screen and press the
key, then the following channel setting screen appears.
Note: The following figure is a channel setting screen for the number of inputs of 9.
channel setting screen
9-36
INP-TN2PHL-E
Select channel No. using the cursor and press the
key.
Selecting “None” does not make recording at that position on the data display screen.
The following is the relation between the No. of the display structure and the data display screen.
No.1
No.2
No.3
No.4
No.5
No.6
No.7
No.8
No.9
No.10
(3) To set trend direction
Move the cursor to “Trend direction” and press the
key, then the setting screen appears.
Select trend display direction using the cursor key and press the
key.
(4) To set the number of display division
key, then the number of display division
Move the cursor to “Display divided” and press the
setting screen (1 to 20) appears. Select the number of division using the cursor key and press the
key.
Note) Display division is not allowed if scale display has been selected.
INP-TN2PHL-E
9-37
(5) To set trend screen scale display
Move the cursor to “Scale display” and select “OFF” or “ON” using the cursor key. Then press
the
key.
The scale of the displayed channel can be arbitrarily changed using the
key.
Note: If the input type is changed in the state where a chart is remaining on the trend screen,
proper display cannot be obtained.
(6) To set graph display
Move the cursor to “Analog meter” and press the
key, then the setting screen appears. Select
a bar gragh display using the cursor key and press the
key.
* The analog meter displays only the channels from No. 1 to No. 4 in the screen structure.
(7) To select channel index
Move the cursor to “Channel index” and press the
key, then the setting screen appears.
Select one from “Channel No. display,” “Tag No. display” and “Unit display” using the cursor
key.
key and press the
* Only seven characters are displayed as TAG No. on the color bar.
In case of 4 channel display
It is selectable to display the combination and the parameter, “Channel index”.
The combination on the real time trend screen and bargraph screen can be set as shown below.
Channel index
CH No. disp.
Tag No. disp.
Unit disp.
Tag display
area
Channel No.
Tag 1
PV
Tag 1
Tag 2
PV
Tag 1
Unit
PV
9-38
INP-TN2PHL-E
9.7 Setting for F value calculation (Setting common to all
channels)
[Explanation]
• Select the calculation constants to be used for F value calculation (Extinction value calculation of
bacteria by sterilization by heating) that are common to all channels.
F value calculation constants: Reference temperature, Z value, Decimal point position
• By selecting a reset temperature, the F value can be reset.
• F value calculation can be manually reset.
Note: Make sure that the number of decimal places of the channel with which F value calculation is to be performed is one.
[Operation]
Select the “parameter setting” on the menu screen and enter the password if the configuration password has been set, then select “F value calculation setting”.
After that, following “F value calculation setting” screen appears.
Select target temperature
Select Z value
Select decimal point poisition
Select F value reset temperature
Manual reset request
(1) To set target temperature
key, then then the following target
Move the cursor to “Target temperature” and press the
temperature setting screen appears. Enter the target temperature using the cursor and press the
key.
(2) To set Z value
key, then the following Z value setting screen
Move the cursor to “Z value” and press the
appears. Enter Z value using the cursor and press the
key.
INP-TN2PHL-E
9-39
(3) To set decimal point position
key, then the decimal point position setting
Move the cursor to “Decimal point” and press the
screen appears. Select the decimal point position of F value calculation result using the cursor
key and press the
key.
(4) To set F value reset temperature
Set F value reset temperature. If PV is less than this temperature, PHL make F value to zero.
key, then the following F value reset
Move the cursor to “Reset temperature” and press the
temperature screen appears.
Enter the reset temperature using the cursor key and press the
key.
(5) Manual reset request
To reset manually the F value, move the cursor to “Manual reset” and press the
9-40
key.
INP-TN2PHL-E
9.8 Setting totalizing (Setting common to all channels)
[Explanation]
It is the common setting for all totalize type.
Each settings are effective to totalize type as shown below table.
Settings
Periodic
Daily
Weekly
Monthly
Annualy Daily(Time) Externaly
Totalize base time
Totalize cycle
Weekly base day
Monthly base day
Totalize start/stop time
External input
: effective
: non-effective
[Operation]
Select the “parameter setting” on the menu screen and enter the password if the configuration password has been set, then select “Totalize setting”.
After that, following “Totalize setting” screen appears.
Setting of totalize base time
Setting of totalize cycle
Setting of weekly base day
Setting of monthly base day
Setting of totalize start/stop time
Setting of external input
INP-TN2PHL-E
9-41
(1) To set totalize base time
Set the totalize base time, date, day, cycle and so on.
In case of totalize type is “Dairy”, PHL records at the setting of “Totalize base time” every day.
In case of totalize type is “Weekly”, PHL records at the setting of “Totalize base time” on
“Weekly base day”.
In case of totalize type is “Monthly”, PHL records at the setting of “Totalize base time” on
“Monthly base day”.
In case of totalize type is “Annual”, PHL records at the setting of “Totalize base time” on January
1st.
In case of totalize type is “Periodic”, PHL records every “Totalize cycle” based on “Totalize base
time”. See following example.
[Example]
< settings >
<Working>
Totalize base time
10:17
Totalize cycle
20min
Recording start time : At 09:22
First recording
: At 09:37
← 10:17 + 23:20
Second recording
: At 09:57
← 10:17 + 23:40
Third recording
: At 10:17
← 10:17 + 24:00 = 10:17
Fourth recording
: At 10:37
← 10:17 + 00:20
Therfore, recording timing is at:
[ Totalize base time + Totalize cycle]
9-42
INP-TN2PHL-E
(2) To set totalize cycle
Set the totalizing cycle for totalize type, “Periodic”.
The setting is selected from 10, 20, 30 minites, 1, 2, 3, 4, 6, 12 or 24 hours.
(3) To set weekly base day
Set the data recording date for totalize type, “Weekly”.
The setting is selected from Sunday, Monday, Tuesday, Wednesday, Thursday, Friday or Saturday.
Operated at all times
Recording status
DI
Time
INP-TN2PHL-E
9-43
(4) To set monthly base day
Set the data recording day for totalize type, “Monthly”.
Setting range is through 1 to 31.
For example, when you set “31” to this parameter and this month is April,
PHL records totalizing data on the last day of the month. This case, it is on April 30th.
(5) To set totalize start time, stop time
Set the totalizing start time and stop time for totalize type, “Dairy (at designated time)”.
(6) To set external input
Set which external input PHL use as trigger to start/stop totalizing for totalize type, “External
input”.
DI or alarm status of all channel is available as external input.
9-44
INP-TN2PHL-E
9.9 Setting for messages
[Explanation]
• When various events occur, messages can be displayed.
• Up to 10 messages of 32 characters each can be registered.
• The message can be set with alphanumeric characters.
• Message timing to be displayed can be set at “ON/OFF of Alarm”, and ON/OFF of DI input.
• Message data can be recorded only in an event file of the memory card.
[Operation]
Select the "parameter setting" on the menu screen and enter the password if the configuration password has been set, then select "Message setting" and desired message number.
After that, following message setting screen appears.
Message setting
Message display timing
(1) To set messages
Move the cursor to “Message” and press the
key, then message screen appears as shown
key for confirmation.
below. Enter message by the cursor and press the
After entry of the message, press the
INP-TN2PHL-E
key to return to message setting screen.
9-45
(2) To set the message display timing
key, then message timing selection screen appears
Move the cursor to “Timing” and press the
key.
as shown below. Select message timing by the cursor and press the
(3) To set the alarm No. and channel No. for the message.
Alarm number selecting screen
DI number selecting screen
Channel selecting screen
9-46
INP-TN2PHL-E
9.10 Unit definition
[Explanation]
The Original unit definition screen allows you to make units with up to 7 alphanumeric characters. Up
to 12 types of units can be registered. The unit can be verified by the unit selection given in Item 9.2.
[Operation]
Select the “parameter setting” on the menu screen and enter the password if the configuration password has been set, then select “Original unit difinition”.
Then following “Original unit definition” screen appears.
Move the cursor to the unit box that remains blank by the cursor key. Press the
following unit naming screen appears.
Enter a unit by the cursor key and then press the
After entry of the unit, press the
INP-TN2PHL-E
key, and the
key for confirmation.
key to return to the “original unie definition” screen.
9-47
9.11 Setting for DI (external control unit) function
[Explanation]
Note: Up to 10 DIs are provided, which allows the following operations to be performed.
(1) Start/stop of record
Using DI, start/stop of the record can be switched.
• The record can also be started/stopped from the keypad on the front face.
• Start/stop switching function of the record is judged according to rise/fall edge of DI.
OFF → ON (Rise): Recording start (No change if the recording is made from the start.)
ON → OFF (Fall): Recording stop (No change if the recording is stopped from the start.)
(2) F value calculation reset
F value calculation can be reset using DI.
• F value calculation reset is judged based on Rise/Fall edge of DI.
OFF → ON (Rise): F value calculation is reset.
ON → OFF (Fall): No change
(3) Start/Stop of totalizing
Totalizing can be started/stopped using DI.
OFF → ON (Rise): Starts totalizing.
ON → OFF (Fall): Stops totalizing.
(4) Totalize reset
Totalize can be reset using DI.
• Totalize reset is judged based on Rise/Fall edge of DI.
OFF → ON (Rise): Totalizing data is reset.
ON → OFF (Fall): No change
(5) LCD ON
LCD can be turned on by DI.
It works as shown below.
DI
Status
OFF → ON
ON → OFF
LCD off
LCD turns on No change
LED ON
No change
No change
(6) Message set
Message can be set using DI.
• In distinction from the function described in (1) to (5) above, message set can be set on the
message setting screen.
• Message set function also works if the functions described in (1) to (5) shown above are allocated to DI. (Both the function allocated to DI and the message set function are operated.)
9-48
INP-TN2PHL-E
(7) E-mail trigger set
E-mail trigger can be set using DI.
• In distinction from the functions described in (1) to (5) above, E-mail trigger can be set on the
E-mail trigger set screen.
• The E-mail trigger function also works even when the functions described in (1) to (5) shown
above are allocated to DI.
(Both of functions allocated to DI and the E-mail trigger set function work.)
[Operation]
Select “Parameter setting” on the Menu screen and then “DI function setting” to display the DI function setting screen.
DI No.
DI function
Move the cursor to the DI No. with which DI function is to be selected and press the
key.
By using the cursor key, select either one of “Function invalid,” “Record start/stop,” “F value calculation reset,” “Totalize start/stop,” “Totalize reset” or “LCD ON”.
INP-TN2PHL-E
9-49
9.12 Setting constant
[Explanation]
Constants can be set to calculation function.
• The number of setting items can be set from 1 to 20.
[Operation]
Select the “parameter setting” on the menu screen and enter the password if the configuration password has been set, then select “Constant setting”.
Then following “Constant setting” screen appears.
Select item
Set value
Move the cursor to a desired setting item, and press the
Enter the set value using the cursor key and press the
9-50
key.
key.
INP-TN2PHL-E
9.13 Ethernet function setting
[Description]
Make the setting as follows to use Ethernet function.
IP address, subnet mask, and default gateway can be set to connect the recorder main unit to Ethernet.
[Note]
• Connect the recorder to Ethernet to use the FTP, Web, E-mail, and MODBUS TCP/IP functions.
Refer to the communication manual for details of connection.
• Contact the system administrator when connecting the recorder to the LAN.
• After making the setting of this parameter, store the setting (see P.8-3), turn off the power, and turn
it on again.
[Operation]
key, and
Move the cursor to “Ethernet setting” on the Parameter setting screen and then press the
the Ethernet setting screen appears. Make the settings required to connect the recorder to Ethernet
(Ethernet function, IP address, Subnet mask, Default, and gateway) and the settings of the functions to
be used (FTP, Web, E-mail, and MODBUS). To use the E-mail function, E-mail setting (1) and Email trigger setting (2) must be made.
To use MODBUS TCP/IP function, Communication setting (3) is required. Refer to the communication manual for details.
CAUTION
• The communication automatically disconnects, if no FTP communication request
is made for 10 minutes.
• The display motion of the paperless recorder may slow down when taking out a
file of large size.
• While the compact flash of the paperless recorder is accessed by FTP communication, do not take out the compact flash.
Furthermore, when the FTP server function is used, inhibit access to the compact
flash in the “Memory card abstract” screen, before taking out the compact flash.
• Do not delete or change the name of a file while the file is being recorded or
totalized.
IP address setting
Subnet mask setting
Default gateway setting
FTP server function setting
FTP access control setting
Web server function setting
E-mail function setting
Modbus TCP/IP setting
INP-TN2PHL-E
9-51
(1) E-mail setting
Check that E-mail function of Ethernet setting is set to ON before carrying out the E-mail setting.
If E-mail setting is made with E-mail function set to OFF, E-mail function cannot be used.
key. On
Move the cursor to “E-mail setting” on the Parameter setting screen and press the
the E-mail setting screen that appears, make the settings required to use the E-mail function
(SMTP IP address, Sender’s mail add, Name, Receiver’s add). Refer to the communication
manual for details of the setting.
SMTP IP address setting
Sender’s mail address setting
Sender’s mail name setting
Receiver mail address setting
(2) E-mail trigger setting
Check that the E-mail function of the Ethernet setting is set to ON before carrying out the E-mail
trigger setting. If the setting is made with E-mail function set to OFF, E-mail function cannot be
used. Move the cursor to “E-mail trigger setting” on the Parameter setting screen and press the
key, and the E-mail trigger setting screen appears. Up to 10 patterns can be selected as Email send timing. Make the setting for E-mail send timing and the contents. Refer to the communication manual for details of the setting.
Trigger timing setting
DI No. setting
9-52
INP-TN2PHL-E
(3) User account setting
The user account is used when security mode is in Logon mode and when FTP communication is
made.
1) Explanation for use in Logon mode
When “Logon” is selected for security mode, logon can be made with the user name and the
password.
The following operations are available depending on the operation level set for every user.
Trend
screen
switching
User level
Recording Log ON /
start and
Log OFF
stop
Parameter
setting
User
account
mode
switching
CF
operation
Calibration
FTP file
deletion
Administrator
Engineer
Operator
Guest
No logon user
: Available
Note) When security mode is used in Logon mode, be sure to register a user in one Administrator level.
2) Explanation for use in FTP function
Check that FTP server function and FTP access control of Ethernet setting are set to ON before
carrying out the user account setting. If the setting is made with FTP server function and FTP
access control set to OFF, connection with the FTP server cannot be established. Note, however,
that if common user name is ftp, connection with the FTP server can be established even if FTP
access control is set to OFF.
Move the cursor to “User account setting” on the Parameter setting screen and press the
key, and the User account setting screen appears. The user name, password, and the access level
for connection with the FTP server can be selected on the screen. Refer to the communication
manual for details of the setting.
(Caution) Do not use blank space as a password.
User name setting
Password setting
User level setting
INP-TN2PHL-E
9-53
9.14 Setting password for parameter setting
[Explanation]
Security mode is selected for the recorder.
A password is set when “Password” is selected for the security mode.
Four-digit password required to display the parameter setting screen and recording start and/or stop
screen can be set as follows.
Set “0000”, then password input isn’t required to display above screens.
[Operation]
(1) Setting of security mode
Select a security mode between “Password” and “Logon”.
When the Logon mode is selected, operations are made as follows.
• When parameters are changed or recording is started/sopped, the user name and the password
should be input to log on to the recorder.
• User name, password and user level are set on the “User account setting” screen.
• The following two methods are available for log off.
1) Log off can be made on “Logon/Logoff” screen in the parameter setting screen.
2) When no key is operated for 10 minutes, log off is made automatically.
(Note) When no user is registered in Administrator level, Logon cannot be selected for
security mode.
(2) Setting of password
Select the “parameter setting” on the menu screen and enter the password, then select “Configuration Password set”.
Then following “Configuration Password set” screen appears.
Configuration password setting
Record key password setting
Press the
press the
key, and password entry screen appears. Enter the password using the cursor key and
key.
9-54
INP-TN2PHL-E
10. OPERATING MEMORY CARD
10.1 Displaying record data of memory card
[Explanation]
The recorded data (trend data file) contained in the memory card set to the main unit can be displayed
on the historical trend screen.
• The meaning of file name is as follows.
• S00****.FDT: File name of the trend data file (A00****.FDT, which is an event data file, is
not displayed.)
The part **** is substituted by 4-digit numerical value, and every time a new
file is created, the value increases sequentially beginning from 0000.
• Every time a recording is started using the
key or by DI input, a new file is created.
A trend file and an event file are created as a set as a new file without fail.
• The date indicates the last time when the writing was conducted on the file.
• The file name cannot be changed on this screen. To change the file name, read in the data in a
memory card on the PC. Observe the following when changing the file name.
1) Change both the trend data file (Sxx.FDT) and the event data file (Axx.FDT)
2) Be sure to give the trend data file a name beginning with S, and give the event data file
a name beginning with A.
3) Be sure to give the same name to the part xxxx of Sxxxx.FDT and Axxxx.FDT. Otherwise the file may not be opened.
4) The file may not be opened with the names S.FDT and A.FDT.
5) Be sure to use 7 characters including S or A at the maximum. Otherwise the file may
not be opened.
6) Do not give the same file name to the part xxxx of Sxxxx.FDT and Axxxx.FDT in separate pairs.
Otherwise the program may not be properly operated and forced termination etc. may
occur.
[Example]
Avoid giving the same file name, 88, to S88 in the upper stage and A88 in the lower stage
as in the example shown below.
Before change
S01. FDT/A01.FDT 2002-11-19 10:00
S02. FDT/A02.FDT 2002-11-19 15:38
After change
S88.
== FDT/A01.FDT 2002-11-19 10:00
S02. FDT/A88.FDT
2002-11-19 15:38
==
INP-TN2PHL-E
10-1
[Operation]
Select the “CF manager and totalize exe”. on the menu screen and enter the password if the CF
manager password has been set, then select “Record data display”. Then following "Record data
display" screen appears.
(1) Select the file to be opened using the cursor key, and press the
record data display screen.
key to display the following
(2) Select a screen group No. you want to display using the cursor key, and press the
10-2
key.
INP-TN2PHL-E
(3) Move the cursor to “Record data display” and press the
key.
and press the
key. Then move the cursor to “ON”
The historical trend screen of the selected group No. is displayed.
Refer to Item 6.7 “Historical trend display” for the method of seeing the historical trend screen.
About loading data from the memory card, following settings are displayed according to currently
settings not the saved settings
• Trend direction
• Number of screen division
• Trend scale display
• Color bar display selection
key while the historical trend screen is displayed, and following “Display time
(4) Press the
setting” screen appears.
key.
Enter the time of currently recorded data you want to display and press the
Then, PHL displays historical trend data at entered day and time.
To display past data, entered day and time appears the bottom of the historical screen. To display
farther data, entered day and time appear the top of this screen.
INP-TN2PHL-E
10-3
10.2 Removing memory card (compact flash)
[Explanation]
By prohibiting the writing to the memory card, the memory card can be removed without stopping the
recording while recording or totalizing is in progress. Refer to [Operation] shown below for the
removing procedure.
• If the internal buffer (memory) of PHL becomes full while the memory card is being removed, the
record data is cut off.
• The internal buffer (memory) of PHL can store the data up to the following limit.
1) Trend data: 400 data (For 400 seconds when the display refresh cycle is 1 second)
2) Event data: 180 data
3) Totalizing data: 1 data (For 10 minutes when the totalizing record cycle is 10 minutes)
• When the memory card is reinserted after it is removed, a new record file (trend file, event file, or an
totalizing file) is created.
[Operation]
Select the “CF manager and totalize exe.” on the menu screen and enter the password if the CF
manager password has been set, then select “Memory card abstract”. The following message appears.
qClock display
wMemory card
loading display
eMemory card indicator
rMemory card writing
status display
(1) Clock display
Displays the date and the time.
(2) Memory card loading display
Displays the memory card loading status.
Flashing: Indicates the state where a memory card is not inserted.
Lit in green: Indicates the state where the memory card can be removed.
Lit in red: Indicates the state where the memory card cannot be removed.
(3) Memory card indicator
Displays the usage of the memory card in a bar graph. Lit in red when 90% of the whole capacity
has been used up.
(4) Memory card writing status display
Kept lit while the measured data is being written into the memory card.
10-4
INP-TN2PHL-E
Press the
key. The following screen appears and the writing into the memory card is prohibited.
Check that the memory card loading display is lit in green. Then then remove the memory card and
key. The
back up the recorded data. After that insert the memory card once again and press the
parameter display screen appears and the prohibition of writing into the memory card is released.
INP-TN2PHL-E
10-5
10.3 Totalizing start/stop setting
[How to start totalize operation]
• Totalize operation can be started from the “Channel setting” or “Math channel setting” screen. On
the “Totalize setting” screen shown above, set “Totalize calculation” to other than off, and perform
either one of the following to start recording.
1) Set “Totalize start/stop” in “Menu/CF manager and Totalize exe.(/Password)/Totalize control” to
key twice.
ON and press the
2) Set “DI1 function” in “Menu/Parameter setting(/Password)/DI function setting” to “Totalize
start/stop” and set DI1 to ON (in the case of the recorder with DI).
[Explanation]
Totalize record file
• A file for totalize recording is created by totalize type as shown by the following table. (Recording is
made in the same format.)
Periodic cycle
T000000.FDT
Daily report
D000000.FDT
Weekly report
W000000.FDT
Monthly report
M000000.FDT
Annual report
Y000000.FDT
Daily report (at designated time)
R000000.FDT
External input
E000000.FDT
• A totalize file is created in a totalize folder (folder name: T000000) in the recording folder.
• A totalize file is newly created every time the base totalize operation is turned on.
• While totalize operation is in progress, a new totalize file is not created even if the power is turned
off.
• The reference time of recording of daily report, weekly report, monthly report, etc. cannot be selected individually but should be synchronized.
• If power failure occurs and power is restored later during totalize operation, the operation resumes
starting from the data before the power failure. (The data during the power failure is not totalized.)
• On totalize 4-channel display screen, totalize start/stop time and the previous totalized value are
displayed.
• Totalizing data by the totalize recording cycle (and not the sum total during totalizing operation) is
recorded in the totalizing file.
• The data can be totalizing to 9 digits.
• If an input error (such as Over, Under, Burnout, Error) occurs, 0 is totalizing. (the error input is not
totalizing. However, if the input type is 0-5V input, and the input is kept open, the value equivalent
to 0.26V is totalizing. If the input type is 0-500mV and the input is kept open, the value equivalent
to 260mV is totalizing.)
• Displayed totalizing data is reset when the totalizing is started.
10-6
INP-TN2PHL-E
[Operation]
Select Menu/CF manager and Totalize exe.(/Password)/Totalize control, and press
totalize control screen appears.
key. Then
To set totalize start/stop
Select “ON” or “OFF” at the parameter, “Totalize start/stop”.
• If “Totalize start/stop” is set to “ON,” totalizing is started when an totalizing start signal is
received.
• If “Totalize start/stop” is set to “ON,” some parameter cannot be set. Refer to Appendix 3.
INP-TN2PHL-E
10-7
10.4 Totalize reset request
[Explanation]
The totalized value in the selected channel can be reset.
If a totalized value is reset during totalization, the value becomes 0.
[Operation]
Select Menu/CF manager and Totalize exe.(/Password)/Totalize reset, and press ENT key.
Then totalize reset request screen appears.
(1) Select channel No.
(2) Start of totalize resetting
(1) Selection of channel number, for which “totalize reset” is performed
Select a channel number, for which “totalize reset” should be performed.
(2) Start of totalize resetting
When the [ENT] key is pressed in this state, the totalized value in the selected channel is reset.
10-8
INP-TN2PHL-E
10.5 Function of reading settings from memory card (compact flash)
[Description]
The setting of the recorder can be read from the memory card.
Setting files (*******.PHL) can be created on the recorder main unit and the parameter loader. Setting files are stored in the PARAMET folder within the memory card. (See the following figure.)
Note: Settings cannot be read while recording or totalizing is in progress.
[Operation]
Move the cursor to “Parameter file load” on the CF manager and Totalize exe menu screen and press
key, and the Parameter file load list screen appears.
the
Move the cursor to the file to be read and press the
key, and reading is started.
On completion of the reading of the setting, the following message screen appears.
INP-TN2PHL-E
10-9
10.6 Function of writing settings in memory card (compact
flash)
[Description]
The setting of the recorder can be written in a memory card.
Setting files (*******.PHL) can be created on the recorder main unit and the parameter loader. Setting files are stored in the PARAMET folder in the memory card. (See the following figure.)
Note: A new setting file cannot be created if a file having the same name already exists within the
memory card. (The setting file cannot be overwritten.)
[Operation]
Move the cursor to “Parameter file save” on the CF manager and Totalize exe menu screen and press
the [ENT] key.
key, and the character entry screen (see below)
Move the cursor to “Save file name” and press the
appears. Enter the file name using the cursor key and the
key. Then press the
key at
[ENTRY] to confirm the entered file name.
Move the cursor to “Parameter save” and press the
memory card is started.
10-10
key, and writing of the setting into the
INP-TN2PHL-E
On completion of the writing of the setting, the following message screen appears.
INP-TN2PHL-E
10-11
10.7 Setting password for memory card operation
[Explanation]
Four-digit password is required to display the “CF manager and Totalize exe.” screen can be set as
follows.
The default setting is “0000.”
[Operation]
Select the “CF manager and totalize exe.” on the menu screen and enter the password if the CF
manager password has been set, then select “CF manager password set”. The following “CF manager
Password set” screen appears.
Press the
key, and the following password entry screen appears.
Enter the password and press the
key.
10-12
INP-TN2PHL-E
11. MAINTENANCE AND INSPECTION
11.1 Recommended replacement cycle of parts
Names of parts
Cycle
LCD (front panel)
5 years
Panel packing
5 years
Fuse (external use)
2 years
Memory card
Lithium battery
6 months
5 years
Remarks
LCD backlight cannot be replaced as a single unit. Return to factory
for repair.
When external fuses are used, replace them every 2 years for preventive
maintenance.
Fuse rating: 250V AC, 1A
• To prevent data from being lost, back up the recorded data once every
6 months.
• If writing error occurs in the memory card, data may be lost. If data
has been written in the memory card to some extent, check if data
writing has been normally performed.
• The compact flash card is a consumable item. If the following
phenomena take place, the card must have come to the end of its
service life. Replace the card in such cases.
1) The number of recording file is found to be larger than expected
even though power failure did not occur or recording was not
interrupted.
2) The recording file loaded into the PC cannot be opened with the
data viewer.
It cannot be replaced as a single unit. Return to factory for repair.
11.2 Calibration
To assure measuring accuracy, perform calibration every year.
For calibration procedure, refer to Chapter 12. Contact our sales representative for details.
11.3 Formatting the memory card
The memory card should be formatted by a personal computer (this recorder is not provided with a
means of formatting the memory card).
Select a PC drive for the memory card and press the right-mouse button. The menu appears, prompting you to select the option. Select “Format” as FAT32, FAT16 or FAT. On the screen that appears,
select the “Start” button to initiate the formatting.
Using CF card adaptor, please check how many capacities it can deal with. If your CF card is out of
the range, don’t format CF card using the adaptor. When format CF card by the adaptor, you may find
it complete format on the Windows. But in that case, PHL might not read the card.
INP-TN2PHL-E
11-1
12. CALIBRATION
The following operation can be carried out.
(1) Calibration of the measured value
(2) Initialization of the set value
12.1 Calibration method of measured values
[Preparation]
Before calibration, prepare equipment as shown below:
Equipment
Power supply
Voltage Generator
Resistance decade box
Digital voltage meter
Specification
0 to 300Vac / 5A
0 to 50Vdc
Resolution: 10 µV (mV range)
Output impedance: less than 2 ohm
Range: 0.01 to 400.000 ohm
Resolution: 0.01 ohm
Display: more than 5 and 1/2 digits
Resolution: 1 µV (mV range)
[Explanation]
Adjustment is not required in an ordinary status. However, to maintain the desired accuracy of the
measured value display, we recommend you to perform calibration periodically by adding calibration
input signals. Add calibration input signals to the channel to be calibrated. To calibrate the input of the
resistance bulb, be sure to perform 500mV calibration beforehand, and then perform the calibration.
Note) If improper calibration input signals are added, the instrument operates improperly. Be
sure to follow the procedure shown above to perform calibration. Otherwise the instrument may operate improperly.
[Operation]
(1) Select the “Calibration password” on the menu screen and enter the password, “1234”, then
following “Calibration” screen appears.
CAUTION
INP-TN2PHL-E
Do not perform “Other functions” and “Adjust data initialization”, since they
are intended to be performed by the manufacturer. Otherwise the instrument
may not operate properly causing phenomena that the input reading is not
properly displayed or the set parameter returns to the value set at the time of
delivery.
12-1
(2) Move the cursor to “Input adjustment.” and press the
appears.
key, then the “input adjustment” screen
In case of 0 to 5V input type
Select channel No.
(3) Select the channel for calibration.
Select the channel for calibration by using the cursor key and press the
key.
(4) Apply 0% input
In the case of resistance bulb input, before performing calibration, be sure that 500mV input
calibration has already finished.
The following are input signals for 0% point calibration.
• Voltage input: 0 mV or 0 V
• Thermocouple input: 0 mV
• Resistance bulb: 50Ω
key.
After input of the input signal for 0% calibration, wait for 30 seconds. Then press the
Zero calibration will start automatically. After calibration, the “Setting completed” message
appears. Pressing
moves to the next span calibration.
(5) Apply 100% input
The input signal for 100% calibration is shown below;
• Voltage input: 50 mV or 500 mV, and 5V
• Thermocouple input: 50 mV
• Resistance bulb: 300Ω
key. Span
After input of 100% calibration input signal, wait for 30 seconds. Then press the
calibration will start automatically. After calibration, the “Setting completed” message appears.
Press the
key.
(6) End of calibration
Move the cursor to “Adjustment completed” and press the
12-2
key.
INP-TN2PHL-E
12.2 Initializing the measured value
[Explanation]
Parameters can be returned to the value set at the time of delivery from the factory.
• After initializing the set value, be sure to store the initialized parameters in a nonvolatile memory.
Otherwise they return to the values before the initialization when the power is turned off.
Note) Thought this function is executed, the adjusted values are not initialized.
[Operation]
(1) Select the “Calibration password” on the menu screen and enter the password, then “Calibration”
screen appears. After that, select “Parameter initialization”, then following “Parameter
initialization”screen appears.
(2) Press the
INP-TN2PHL-E
key to start initialization. To cancel it, press the
12-3
key.
(3) Press the
key, and the setting value of parameters are initialized at the shipment.
12-4
INP-TN2PHL-E
13. TROUBLESHOOTING
If the recorder does not operate normally, take a remedy according to the table given below. For a complicated trouble, contact our Sales Representatives.
Situation
Does not work at all.
Keys do not work.
“System Error” is
displayed when power
is ON.
Check
1) Is the power supply terminal connection correct?
Connect correctly.
2) Is power being supplied properly?
Supply correctly.
1) Does the screen display correctly?
If keys only do not work, key switch may be faulty.
Contact our Service
Center
2) There are some parameters that cannot be set during
recording.
Check if setting has been attempted during recording.
Stop recording at once.
It is displayed when a fault occurs in CPU. Turn the power
ON again. If it does not return to normal condition, CPU may Contact our Service
Center.
be faulty.
The record swings over to 1) Is digital indication displayed correctly? If the input is not
connected correctly, burnout may occur or over- or underthe 0% side or the 100%
indication may occur
side.
2) The record swings over the indication range if the
indication range is not set correctly.
The indication changes
too much.
The data indicator
indicates “Over”,
“Under” or “Error”.
Remedy
To match the indication to that of the field indicator, use PV
shift given in Item 9.2 (12).
If the input is not connected correctly or a signal that is
different from the input type is connected, the indication
becomes faulty.
Connect correctly.
Set the indication range
correctly.
• Connect correctly.
• Set the input type
according to the input
signal.
1) Is the memory card connected properly?
2) Is the memory card full?
Recording data is not
written in memory card
3) If the measuring channel is set as “Indication only” or
“Skip”, data is not recorded.
4) The memory card may be defective.
“Recording has been
stopped because the
compact flash has run
out of capacity.
Replace the compact
flash.” is kept displayed.
1) The compact flash has run out of capacity.
“No battery! Please
exchange the battery” is
kept displayed.
Battery becomes low voltage. So, it might reset the clock at
power on or it couldn’t work totalizing correctly.
2) Was the
key pressed after the compact flash is
replaced with the one with sufficient capacity?
Fix the memory card
according to Item 2.2.
Check the status of the
memory card with the PC.
1) Replace the compact
flash with the one
with sufficient
capacity, and then
press the
key.
2) Press the
key.
Contact our Service
Center.
1) Check if power failure occurred during recording.
The number of recording
file is found to be larger
than expected.
The recording file cannot
be opened with the data
viewer.
INP-TN2PHL-E
2) Check if the auto file division function is performed.
Check the auto file
division function setting.
3) The memory card may have come to the end of its service
life.
1) The version of the data viewer may not be the latest.
Replace the memory
card with a new one.
Check the version of the
data viewer.
2) The memory card may have come to the end of its service
life.
Replace the memory
card with a new one.
13-1
14. SPECIFICATIONS
1. Input system
Number of input points:
9 points or 18 points (Can be selected at
the time of purchase)
Input circuit:
Input mutual isolation
Resistance bulb measured current:
about. 1 mA
Measuring cycles:
9 or 18 points….100ms cycles
Recording cycle: 1 sec to 12 hours
Every recording cycle, measured value
is calculated in accordance with recording type, minimum/maximum, average or
point value recording, using sampling
data.
Input types:
Thermocouple, resistance bulb, DC voltage, and DC current (Shunt resistors are
fitted in input terminals).
Note) Provide a shunt resistor (type:
PHZP0101) separately.
Measuring range
Input types
Reference range
400.0 to 1760.0°C
Thermocouple B
0.0
to 1760.0°C
R
0.0
to 1760.0°C
S
–200.0 to 1370.0°C
K
–200.0 to 800.0°C
E
–200.0 to 1100.0°C
J
–200.0 to 400.0°C
T
0.0
to 1300.0°C
N
0.0
to 1760.0°C
W
–200.0 to 900.0°C
L
–200.0 to 400.0°C
U
0.0
to 1300.0°C
PN
–200.0 to 600.0°C
Resistance bulb JPt100
–200.0 to 600.0°C
Pt100
–60.0 to 180.0°C
Ni100
–200.0 to 600.0°C
Pt50
–50.0 to 200.0°C
Cu50
0.00
to 50.00mV
DC voltage
50mV
0.0
to 500.0mV
500mV
1.000 to 5.000V
1-5V
0.000 to 5.000V
0-5V
Note) B, R, S, K, E, J, T, N : JIS C 1602, DIN IEC 584-1
W : 5%Re-26%Re · W (Hoskins Mfg. Co. USA)
L : Fe-Cu · Ni (DIN 43710)
U : Cu-Cu · Ni (DIN 43710)
PN: Platinum
JPt100 : JIS C 1604-1989 (Old JIS Pt 100)
Pt100, Pt50 : JIS 1604, DIN IEC 751
Selection of input types:
By key operation on the front panel. Note
that the same input type (thermocouple,
resistance bulb, voltage) should be set
every 2 channels. Refer to “Setting
method of input types” for details.
Burn-out function:
Equipped in thermocouple and resistance
bulb inputs as standard, and overswings
the recording to 100% side.
Thermocouple burn-out current:
approx. 0.2 µA
Input filter function:
Settable for each channel (primary delay
filter)
Time constants are settable in the range
from 0 to 900 sec.
INP-TN2PHL-E
Scaling function: Possible by DC voltage (current) input
Scaling range:-32767 to 32767
Decimal position:
settable at any point
Unit symbol: settable up to 7 digits and
125+12 types
Subtraction function:
Subtraction between each channel is allowed.
Totalizing function:
The measured value of each channel can
be totalized. The base time can be selected from Day, Hour, Minute, and Second.
F value calculation function:
F value (extinction value of bacteria by
sterilization by heating) can be calculated
from the measured temperature by each
channel.
Square rooter function:
Square rooter can be performed against
the input value per each channel.
Logarithmic calculation function:
The measured value of each channel can
be displayed in exponential form.
Mathematics function:
The math function as shown below is
available.
1) Formula
It can be set 1 main formula and 3 temporary one.
Addition, Subtraction, Multiplication,
Division Absolute value, X to the power
of Y, Logarithm, Natural logarithm,
Exponential function, Humidity, Average value, Maximum value, Minimum
value.
2) Input signal
DI (DI1 to DI10), Totalize (ch1 to ch30),
Analog input (ch1 to ch30), Constant
(No.1 to No.20), Communication input
(No.1 to No.12)
2. Indication system
5.7” TFT color LCD (320 x 240 dots)
with backlight, no contrast adjustment
Note) The LCD may have some pixels that do not stay
on or off.
Due to the characteristics of liquid crystal, the
brightness may not be uniform, which is not a
failure.
Color of indication:
14 colors
Applicable language:
English, French (switchable)
Life of backlight: 50,000 hours
(the complete indicator unit should be
replaced when replacing backlight).
Indicator:
14-1
Direction: vertical and horizontal
Number of channels: 10 channels or 4
channels for the group on one screen (Input: 18 points at the maximum).
Display refreshment cycles:
select from 1 second to 12 hours
No numerical value display. Scale display/
no-display can be selected.
Bar graph display:
Direction: vertical
Number. of channels: 10 channels or 4
channels for the group on one screen (Input:18 points at the maximum).
Display refreshment cycles: 1 second.
Analog meter display:
Display for up to 4 inputs per group (input from 1 to 4). Display in bar graphs or
in analog meters can be selected.
Display refresh cycle: 1 second
Digital display:
Number of channels: 10 channels or 4
channels for the group on one screen (Input:18 points at the maximum).
Display refreshment cycles: 1 second.
Totalizing data display:
Number of channels: 10 channels or 4
channels for the group on one screen (Input: 18 points at the maximum)
Display refresh cycle: 1 second.
Event summary display:
Alarm summary and message summary
can be displayed. The message occurrence information and message display
can be switched.
Parameter display/set:
Already-set Data Display and Set Change
Display screen
TAG indication: Number. of characters to be displayed:
Up to 8 characters (note 1) at 10 channels on one screen or up to 16 (= 8 ×
2) characters at 4 channels on one
screen.
Note 1: On some screen, it can be displayed only 7 characters.
Characters to be displayed:
Alphanumerical characters
Tag, unit and channel number display:
It depends on the screen. See below
table.
Trend display:
Items
Number of channel
on one screen
TAG1
TAG2
unit ch number
+
+
+
Trend
+
4 or less
x
x
x
more than 5
+
+
+
+
Bar graph 4 or less
x
x
x
more than 5
all items are displayed
4 or less
Analog
v
v
more than 5 No1 to 4
v
meter
x
x
x
others
4 or less
Digital
all items are displayed
v
v
more than 5
v
x: only 1 item can be displayed.
+: only 2 items can be displayed.
v: 3 items can be displayed. Only TAG2 can’t be displayed.
Screen
Historical trend display:
The past data can be displayed from the
Compact Flash or internal memory. The
past data file can be read and displayed
with scroll display function or jump the
cursor to the position which you entered
date and time. Scale display/no-display
can be selected.
Number of screen groups:
Four groups (Up to 10 channels per 1
group can be registered.)
3. Keyboard
No. of Keys:
Function:
8
Use to select various screens and set
various parameters.
4. Recording function
External memory media:
Compact Flash card
(Format as FAT32, FAT16 or FAT, or recorder can’t read and write.)
Internal memory:
8 Mbits SRAM with battery for backup.
Recording capacity:
2GB maximum (compact flash). Limiting
the recording file to 64MB is recommended (for 112 hours if display refreshment cycle is 1 second. See “18. Recording capacity.” (p14-6).)
If the capacity becomes 256MB or more,
a new file is created automatically to continue recording.
*Please change the compact flash every
six month to prevent the data losing.
Recording method:
Turning ON the REC key allows measured
data to be written at fixed cycles.
Recorded as a new file whenever the recording starts
Data save cycles:
Linked to the display refreshment cycles
on the “Trend display” screen. However,
they are automatically set to about 1
minute if the refreshment cycles are set
to less than 1 minute.
Trend data:
Average, instance or min. and max. measured values out of measured data that
are sampled at the measuring cycles are
saved.
Event data:
Saves alarm data, message data and
power ON data when the power turns off
and on during recording.
14-2
INP-TN2PHL-E
Totalizing value data:
Totalizing value data at designated timing is recorded per channel.
Totalized value data at designated totalized value recording cycle or the sum total is recorded in the totalizing file.
You can choose which type you want to
record.
For each cahnnel. it can be select as totalizing action from Analog input totalization, Digital input count or period of Digital input ON, and it can be select as totalizing period type from Dairy, Weekly,
Monthly, Annual, Periodic, Dairy (time set)
or External input signal.
Even if a power failure occues during totalization and then the power is
restored,the totalization restarts from the
value before power failure.
Storage capacity :
Approximately 1.5 years when the display
refresh cycle is 30 seconds (in the case
of 9-channel recording in ASCII data format, and 256MB Compact Flash is used).
Refer to Item 2.3.
Residual capacity of memory:
Indicates the memory which has already
used on the screen. If the residual capacity is none, the recording stops.
Compact flash: Type : PHZP1301-512
(If you use a CF card other than the above,
we can not guarantee the proper operation. In addition, please check our web
site for other CF cards which we conducted performance tests on. We will keep
information updated.)
Recommended PC card adaptor:
SanDisk Corp. SDAD-38
Data format:
Either of ASCII or binary format can be
selected. (Switching cannot be made
while the recording is in progress. In the
case of ASCII format, the data can be directly read on Excel, etc.)
Note: The data recorded in binary format
cannot be read directly.
Approximately 166 bytes per 1 sampling
(for 9-channel input in ASCII format) or
approximately 40 bytes (for 9-channel
input in binary format)
5. Alarm function
No. of settings:
Type of alarm:
Indication:
Hysteresis:
Relay output:
INP-TN2PHL-E
Up to 4 alarms for each channel are
settable.
High/Low limits
Status (alarm types) is displayed on digital display unit when an alarm occurs.
History display on alarm summary (Alarm
start/cancel time and alarm types)
Set within the recording range of 0 to
100% (it is effective only in case of high/
low limit alarm)
Number of points; 10 (option: Cannot be
selected if the number of input points is
18.)
Transistor output (Open collector):
Number of points; 18 (option)
Alarm latch function:
Keeps alarm indication and alarm output
turning on after alarm reset.
ON/OFF operation is performed according to key setting.
6. Power supply
Rated power voltage:
100 to 240V AC
Range of operating voltage:
90 to 264V AC
Supply frequency:
50/60Hz (both employable)
Power consumption
100V AC
About 36VA
240V AC
About 47VA
7. Structure
Mounting method:
Panel-mounted (vertical panel)
Thickness of panel:
2 to 26 mm
Materials:
PC-ABS for case and bezel
Color:
Black
External dimensions:
Panel-mounted: 160 (W) × 144 (H) × 185
(D) mm
Mass:
About 1.5 kg (no option)
External terminal board:
Screw terminals (M3 thread)
8. Normal operating condition
Power voltage: 90 to 264V AC
Supply frequency:
50/60 Hz ± 2% (both employable)
Ambient temperature:
Panel-mounted:
0 to 50°C (without Ethernet option*1)
0 to 40°C (with Ethernet option*2)
Portable:
0 to 40°C
Ambient humidity:
20 to 80%RH
Vibration:
10 to 60Hz 0.2m/s2 or less
Shock:
None
Magnetic field:
400 A/m or less
Signal source resistance:
Thermocouple input …. 1kΩ or less
Resistance bulb input… 10Ω/wire or less
(resistance of each wire of 3-wire system
should be balanced).
Voltage input… 0.1% or less of input resistance
Mounting posture:
Forward tilt 0°, backward tilt within 30°,
horizontal 0°
Warm-up time:
One hour or more after power ON
*1: In case of the 12th digit of ordering code is “Y” or “R”.
*2: In case of the 12th digit of ordering code is “E” or “W”.
14-3
Withstand voltage:
Power terminal – ground: 2000V AC, 1 min
Input terminal – ground: 500V AC, 1 min
Alarm terminal – ground: 2000V AC, 1 min
Alarm terminal – alarm terminal:
750V AC, 1 min
Communication terminal – ground:
500V AC, 1 min
Alarm terminal (open-collector) – ground:
500V AC, 1 min
9. Safety and EMC standard
Safety standard: Based on IEC61010-1
EMC standard: Based on EN61326
10. Transportation/storage conditions
Temperature:
Humidity:
Vibration:
Shock:
–10 to +60°C
5 to 90%RH, no condensation
10 to 60Hz, 2.45m/s2 or lower
294m/s2 or lower (packed state)
13. Effect on operation
11. Reference standard
Accuracy/resolution:
Measuring conditions (23± 2°C, 65± 10%
RH, power voltage, frequency fluctuation
within ± 1%, no external noise, warm-up
time of 1 hour or more, vertical mounting,
standard values of signal source resistance and wiring resistance... within 1%)
Input types
Thermocouple B
R
S
K
E
J
T
N
W
L
U
PN
Digital indication
accuracy
Note 1
Digital indication
resolution
± (0.15%+1 digit)
±(0.3%+1 digit)
for the range shown below
Thermocouple B :
400 to 600°C
Thermocouples R and S :
0 to 300°C
Thermocouples K, E, J, T,
L and U : -200 to -100°C
0.1°C
Resistance JPt100
bulb
Pt100 ± (0.15%+1 digit)
Pt50
0.1°C
Ni100
±
(0.5%+1
digit)
Cu50
DC voltage 50mV
10µV
500mV
100µV
±
(0.15%+1
digit)
1-5V
1mV
0-5V
1mV
Note 1) Digital indication accuracy is a percentage (%) of the value in
the measuring range on page 1.
Note 2) No error of reference contact compensation of thermocouple is
included.
Error of reference contact compensation:
K, E, J, T, N, L, U, PN: ± 0.5°C
R, S, B, W: ± 1.0°C
(when measured at 0°C or more)
Max. input voltage:
Thermocouple, resistance bulb, DC voltage: ± 10V DC (continuous)
Input resistance: Thermocouple, DC voltage: About 1MΩ
12. Others
With calendar function (Christian era)
Accuracy: ± 100 ppm or less (monthly error: about 2 minutes)
However, time error at power ON/OFF is
not included.
Memory backup: Parameters are saved to the internal nonvolatile flash memory.
The clock and totalized data are backed
up with built-in lithium battery.
Insulation resistance:
100 MΩ (when measured between each
terminal and ground by using a 500V DC
megger)
Clock:
Effect of power supply fluctuation conditions:
For the fluctuation in the range from 90 to
264V AC (frequency: 50/60Hz)
Reading change: ± (0.2%+1 digit) or
lower.
For the fluctuation in the range from 47 to
63Hz (power voltage: 100V AC)
Reading change: ± (0.2%+1 digit) or
lower.
Effect of input signal resistance:
Thermocouple input: 50µV± 1 digit per
100Ω
DC voltage: Fluctuation for resistance
value equivalent to 0.1% of the input resistance: ± (0.2%+1 digit) or lower.
Resistance bulb (for wiring resistance of
10Ω for 1 line (the same for 3 lines))
Reading change: ± (0.2%+1 digit) or
lower.
Effect of ambient temperature:
Reading change: ± (0.3%+1 digit)/10°C or
lower.
Effect of Mounting position:
For the backward 30° slant
Reading change: ± (0.2%+1 digit) or
lower.
Effect of vibration:When sine wave of 10 to 60Hz with the
acceleration of 0.2m/s2 is applied in each
direction for 2 hours.
Reading change: ± (0.2%+1 digit) or
lower.
14. Additional function (option)
■ Alarm relay output/DI (11th digit of code symbols: “1”)
A card with 10-point relay output and 5-point DI input can
be mounted.
Cannot be mounted if the number of input points is 18.
Terminal structure:
M3 screw terminal
Alarm relay output:
Contact output (SPST:10 points),
Individual channel or common output (OR
output) allowed.
DO1: Contact capacity; 150V/3A AC, 30V/
3A DC (resistance load)
DO2-10: Contact capacity; 240/3A AC,
30V/3A DC (resistance load)
14-4
INP-TN2PHL-E
No-voltage contact input (5 points)
The following control is allowed by contact input.
(1) Recording start/stop
(2) Message set
(3) F value calculation reset
(4) Totalizing start/stop
(5) Totalizing reset
(6) LCD turns on
On pulse width: 200msec or longer
Off pulse width: 200msec or longer
■ Communication, Alarm output with open-collector and DI
(12th digit of code symbols: “R”)
A card with communication with RS485. MODBUS protocol,
18-points open-collector output and 5-points DI input is available.
Terminal structure:
M3 screw terminal for communication,
DO11 (alarm output with open-collector),
DI6 and power supply for DIO.
D-sublight type 25 pins connector with
female terminal for DO12 to DO28 (alarm
output with open-collector), and DI7 to
DI10.
Communication: Physical specifications: EIA RS485
Communication protocol: Modbus (RTU)
Communication method:
2 wire method. Half duplex bit serial,
start-stop sync type.
Data type:
8 bits. Parity: odd/even/none.
Stop bit: 1 bit.
Communication rate: 9600, 19200bps
Connection aspect:
multi-drop/up to 32 recorders connectable including master station
Communication distance:
Total extension 500m or less
RS232C/RS485 Signal converter (recommendation):
Isolated type
Manufacture: OMRON Corporation
Model: K3SC-10
Alarm output:
Open-collector transistor output (18
points)
Electrical Rate: 30Vdc, 100mA (resistance load)
DI input:
No-voltage contact input (5 points)
The following control is allowed by contact input.
(1) Recording start/stop
(2) Message set
(3) F value calculation reset
(4) Totalizing start/stop
(5) Totalizing reset
(6) LCD turns on
On pulse width: 200msec or longer
Off pulse width: 200msec or longer
DI input:
INP-TN2PHL-E
15. Ethernet
The following can be performed through the Ethernet function.
■ HTTP server (Internet Explorer 6 is available) Note 1
Measurement display:
Digitally displays the measurement of
each channel of the recorder and alarm
occurrence status.
Event summary display:
Displays event summary including alarm
ON/OFF and issuance of messages.
Main unit information display:
Displays memory use conditions and information on the main unit such as the
battery end warning.
Integrated value display:
Digitally displays the integrated value of
each channel of the recorder.
■ FTP server (Internet Explorer 6, FFFTP ver.1.9.2a and
command prompt are available.) Note 1
File download:
Record files stored in compact flash (CF)
can be downloaded from the browser.
File delete:
Record files stored in CF can be deleted
from the browser.
Access authentication:
Authenticates access authority to FTP
server.
■ SMTP (e-mail client)
Transmits e-mails to specified address
under the following conditions.
(1) When an alarm turns on or off
(2) When DI is set to ON or OFF
(3) When an error occurs to the main unit
(such as low battery or no memory
space)
(4) At specified intervals
■ MODBUS TC/IP
Data read:
Settings can be read through MODBUS
TCP/IP communication.
Data write:
Settings can be written through MODBUS
TCP/IP communication.
Note1: Neither Netscape nor Mozilla Firefox
are available.
16. Support software
The following software is provided as standard.
• PC/AT-compatible machine
• Operation on PC98-series machines by NEC is not guaranteed.
• Operation on self-made or shop-brand PCs is not guaranteed.
■ Loader software for PC
Major function: Performs various parameter setting/
change of the main unit
O/S:
Windows 2000/XP, Windows 7 (Home
Premium, Professional (Not applicable for
64 bit version))
Required memory:
64MB or larger
Disk drive:
Windows 2000/XP/7-capable CD-ROM
drive
14-5
Hard disk capacity:
Free capacity of 30MB or larger required
Printer:
Windows 2000/XP/7-capable printer and
printer driver
Note) PC loader communication cable (type
PHZP1801) is separately required.
■ Data viewer software
Major function: Regenerates the past trend record on the
PC from the data in the Compact Flash.
Provided with historical trend display and
event display functions.
O/S:
Windows 2000/XP, Windows 7 (Home
Premium, Professional)
Required memory:
64MB or larger
Disk drive:
Windows 2000/XP/7-capable CD-ROM
drive
Hard disk drive: Free capacity of 30MB or larger required
Printer:
Windows 2000/XP/7-capable printer and
printer driver
18. Recording capacity
If the number of input points is 9, there are no events such
as messages, and the data format is ASCII, the recording
can be made for the period of time listed in the tables shown
below. (When the number of input points is 18, the period is
approximately one half of those listed in the table.)
(In binary format, the period is approximately 4 times as
long as those listed in the table.)
CompactFlash size
Display refreshment cycle
Recordable capacity (about)
256MB
1 sec
10 sec
30 sec
1 min
18 days 187 days 1.5 years 3 years
When Compact Flash is not used, up to 600K bytes of the
recording data and the event data can be stored in the main
unit. (In case of 9-channel in Max./Min. recording, approximately 15,300 data can be stored. For 4 hour at the display
refresh cycle of 1 second. The number of the save data
varies depending on the number of the event data.
17. Standard functions
Function
Record range
voluntary setting
Description
Recording range can be set by channel.
Input type setting
Input can be set by channel.
(Key operation on the front face)
Set the same input type for every 2 channels.
See “SELECTING INPUT TYPE” on the last page.
Skip function
Trend display
Skips arbitrary channel display/recording.
Time display: Time is displayed at the top of the
trend display screen.
Alarm display: On occurrence of an alarm and the
restoration, alarm is displayed in
the alarm display field.
The Compact Flash usage is displayed at the top
of the bargraph.
TAG name display
Screen name
display
Unit creation
By channel, Maximum of 8 characters.
Displays the screen name (maximum of 16
characters).
Industrial units can be arbitrarily created, Maximum
of 7 digits, 12 types.
Arbitrary scaling is allowed in the case of DC
voltage input. Decimal point position can also be
arbitrarily set in the range from -32767 to 32767.
Scaling function
PV shift
Shift the zero point and slant of the reading.
Input filter
Prevents sudden fluctuation of input for each
channel (primary delay filter).
Time constant: 0 to 900 seconds.
Burnout function
Displays the break of thermocouple/resistance
bulb input by scaling out to 100% side.
Regenerates and displays the data stored in the
compact flash by scrolling the screen or jump to
time when you entered.
Historical
trend display
14-6
INP-TN2PHL-E
APPENDICES
Note) Data such as burn-out, error, and time of occurrence are recorded as
–32768 (with decimal point). Over-/under range Indication is recorded
as 32767/-32767 (with decimal point).
Appendix 1 Recording format (ASCII)
A-1
MAX. value and
MIN. value of
each channel
(1) Trend data file
INP-TN2PHL-E
Parameter set values, channel No.,
TAG name, recorded color, input types,
units, display range (0%), display
range (100%), etc.
(2) Event data file
A000001.FDT
PHL11B11-E10YY
SNo.A2M0262T
Ver.V07L
2002/ 4/18 23:32:00,A,01,2,02,1
2002/ 4/18 23:32:00,M,Low temperature attention
2002/ 4/18 23:45:22,A,03,3,01,1
2002/ 4/18 23:45:22,M,Humidity is abnormal.
2002/ 4/18 23:47:21,A,03,3,01,0
2002/ 4/18 23:47:28,A,03,4,02,1
2002/ 4/18 23:47:28,M,Humidity is abnormal.
2002/ 4/19 00:39:46,A,03,4,02,0
2002/ 4/19 00:41:26,A,01,2,02,0
2002/ 4/19 00:41:26,M,Low temperature attention off
2002/ 4/19 00:42:27,A,03,4,02,1
2002/ 4/19 00:42:27,M,Humidity is abnormal.
2002/ 4/19 00:43:12,A,03,4,02,0
2002/ 4/19 00:52:37,A,01,1,01,1
2002/ 4/19 00:52:37,M,High temperature attention
2002/ 4/19 02:05:58,A,01,1,01,0
2002/ 4/19 02:05:58,M,High temperature attention off
2002/ 4/19 02:42:38,A,01,2,02,1
2002/ 4/19 02:42:38,M,Low temperature attention
2002/ 4/19 02:55:48,A,03,3,01,1
2002/ 4/19 02:55:48,M,Humidity is abnormal.
2002/ 4/19 02:57:51,A,03,3,01,0
2002/ 4/19 02:57:57,A,03,4,02,1
2002/ 4/19 02:57:57,M,Humidity is abnormal.
2002/ 4/19 03:50:02,A,03,4,02,0
2002/ 4/19 03:51:40,A,01,2,02,0
2002/ 4/19 03:51:40,M,Low temperature attention off
2002/ 4/19 04:02:53,A,01,1,01,1
2002/ 4/19 04:02:53,M,High temperature attention
2002/ 4/19 05:16:14,A,01,1,01,0
2002/ 4/19 05:16:14,M,High temperature attention off
,01
Message data
,01
,01
,01
,01
“Occurrence of alarm” data
Year, month, day, time, type (A), channel No., alarm No.
Alarm types (1: H, 2: L)
Alarm ON (1) and alarm OFF (0)
,01
,01
,01
,01
,01
,01
,01
,01
A-2
INP-TN2PHL-E
Appendix 2 Parameters that cannot be set during recording
Channel parameters
Input types
Units
Scaling (measuring range, engineering unit)
Square rooter
Logarithmic display
TAG1, TAG2
Display color
Display range
Recording action
F value calculation function
F value calculation decimal place
Unit parameters
Display refreshment cycles
Display naming
Screen structure
Clock
Record data format
Functions that cannot be Channel parameter copying function
used during recording
Parameter initialization
Appendix 3 Parameters that cannot be set while totalizing is
under way
Channel parameters
Totalize tag
Totalize calculation
Totalize type
External input
Totalize base time
Totalize operation
Totalize unit
Totalize cut value
Totalize scale value
Totalize reset input
Functions that cannot be Parameter initialization
used during totalizing.
Totalize setting
Totalize base time
Totalize cycle
Weekly base day
Monthly base day
Start time, Stop time
External input
Unit parameters
Clock
Record data format
INP-TN2PHL-E
A-3
Appendix 4 Opening the PHL record data in ASCII format on
Excel
Note 1: The record data in binary format cannot be opened following the procedure shown below.
(Refer to Item 9.1 (11) for details.)
Note 2: The record data of 10MB or larger in case of 9-point input, and 5MB or larger in case of 18point input cannot be opened on Excel. In these cases, read the data using the data viewer
(contained in the attached CD-ROM) and perform CSV conversion to divide the file, which
allows the data to be read.
q Start up Excel, select “File(F)” and the “Open (O)” on the menu to display the following screen.
w
w Select “All” for the file type, and select PHL record data (S****.FDT).
e Selecting the file displays the following data format setting screen. Select “Dividing characters
such as a comma or a tab…..” for the original data format, and then press the “Next” button.
e
r Pressing the “Next” button displays the following screen.
Check “Comma (C)” in the dividing character setting.
t Pressing the “Exit (E)” button displays the record data of PHL.
A-4
INP-TN2PHL-E
Appendix 5 Timing of recording
The timing of recording varies depending on display refresh cycle and integration record cycle.
Example: When the recording is started at 08:45 at the display refresh cycle of 20 minutes, the data is recorded next when the clock indicates 0, that is, at 09:00. The recording will thus be performed at
09:20, 09:40, 10:00 …..etc.
Display refresh
cycle
Data is recorded when the PHL clock indicates the following time.
1 second
Every second
2 seconds
Every even-numbered second
3 seconds
At 0, 3, 6, 9, 12, 15, 18, 21, 24, 27, 30, 33, 36, 39, 42, 45, 48, 51, 54, 57 seconds
5 seconds
At 0, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55 seconds
10 seconds
At 0, 10, 20, 30, 40, 50 seconds
20 seconds
At 0, 20, 40 seconds
30 seconds
At 0, 30 seconds
1 minute
Every minute (When 0 is displayed. The same for the following)
2 minutes
Every even-numbered minute
3 minutes
At 0, 3, 6, 9, 12, 15, 18, 21, 24, 27, 30, 33, 36, 39, 42, 45, 48, 51, 54, 57 minutes
5 minutes
At 0, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55 minutes
10 minutes
At 0, 10, 20, 30, 40, 50 minutes
20 minutes
At 0, 20, 40 minutes
30 minutes
At 0, 30 minutes
1 hour
Every hour (When “0 m :0 s” is displayed. The same for the following)
2 hours
Every even-numbered hour
3 hours
At 0, 3, 6, 9, 12, 15, 18, 21 hours
4 hours
At 0, 4, 8, 12, 16, 20 hours
6 hours
At 0, 6, 12, 18 hours
12 hours
INP-TN2PHL-E
At 0, 12 hours
A-5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement