Cozi Beebi | 7003 | User manual | Cozi Beebi 7003 User manual

Group 1/2/3
Model: 7003
9 - 36 kg
Infiniti
1
3
Universal Forward-Facing Restraint System suitable for children with
body weight 9 to 36 kg. Approximately for ages 9 months to 12 years.
ADULT ASSEMBLY REQUIRED.
USER MANUAL
2
CONTENTS
IMPORTANT
1
WARNING & SAFETY INSTRUCTIONS
2
PART LIST & LEGEND
4
ASSEMBLY INSTRUCTIONS
5
Group 1
To Loosen the Harness
To Adjust the Heights of the Harness Straps
To Fit Child Car Seat to the Vehicle Seat
To Secure Child
To Tighten the Harness
6
7
8
9
11
12
Group 2
To Remove the 5-Point Harness
To Secure Child
To Adjust the Headrest
13
14
15
16
Group 3
To Remove the Backrest
To Secure Child
17
18
19
CARE & MAINTENANCE
About Harness Buckle
To Clean the Harness Buckle
To Clean the Plastic Parts
Washing Instructions of Fabric Cover
To Install the 5-Point Harness
To Remove the Fabric Cover
20
20
20
20
21
21
24
WARRANTY
Product Registration
25
IMPORTANT
Please read all the information contained in this instruction manual carefully
before using and during installation of the child car seat.
For future reference, store this instruction manual in the pouch located at the
back of the child car seat.
This child car seat has been approved according to the latest European
safety standards ECE R44/04 and is suitable for children weighing within the
following range per each Group:
Age*
Group Body Weight of Child
1
9-18 kg
2
15-25 kg
Approx. 9 months - 3 years
Approx. 3 years - 6 years
3
22-36 kg
Approx. 6 years - 12 years
* The age column listed above is for reference only. ALWAYS refer to the
body weight of child as the guideline to the correct grouping of car seat to use.
This child car seat applies the UNIVERSAL child restraint system. It is
approved in accordance to ECE Regulation R44/04, for general use in
vehicles. This child car seat will fit most, but not all vehicle seats.
A correct fit is likely if the vehicle manufacturer has declared in the vehicle
handbook that the vehicle is capable of accepting a UNIVERSAL child
restraint for this age group.
This child restraint system has been classified as UNIVERSAL under more
stringent conditions than those which applied to earlier designs which do not
carry this notice.
This child car seat must only be used in a FORWARD-FACING SEAT
equipped with a 3-POINT SAFETY BELT that meets the UN/ECE R16 or
other equivalent standard.
Before purchase, check to ensure that the child car seat fits properly in your
car, as different types of restraint system is used in cars. In case of doubt,
please contact your retailer or manufacturer of the restraint system.
Infiniti 1/2/3
1
WARNING & SAFETY INSTRUCTIONS
Use this child car seat as a FORWARD-FACING SEAT only.
Use this child car seat with a 3-POINT SAFETY BELT.
NEVER USE A 2-POINT SAFETY BELT, as this could cause death or injury
in the event of an emergency stop or collision.
Children are safer when properly restrained in vehicle REAR SEAT, rather
than vehicle front seat. (according to accident statistics)
DO NOT use this child car seat on vehicle front seat if it is equipped with
airbags.
The safety of your child car seat can only be ensured if all instructions in this
user manual have been followed correctly and if it has been installed
accordingly.
The correct fitting of the seat belt is of vital importance for the safety of your
child. Note that seat belt routings are different for each group. NEVER use
belt routing other than specified.
DO NOT make any alterations to this child car seat, as this could affect part
or overall safety of the seat.
DO NOT leave children alone in a car, even for a short time.
DO NOT replace the fabric cover with any other than the one recommended
by manufacturer.
DO NOT use the child car seat without its fabric cover, as the cover
contributes to the safety of the seat.
DO NOT use second-hand child car seat.
The Cozi Beebi Infiniti may only be used as a child car seat only and it is not
intended for home use.
Instruct your child NOT to play with the belt buckle.
Take short breaks on longer journey to allow your child some freedom of
movement.
Infiniti 1/2/3
2
All foldable rear seats must be locked. The backrests of the vehicle seats
must always be in an upright position.
Once the car seat is fitted, make sure no parts can become trapped in the
doors or the seat mechanism.
The hard items and the plastic parts of the child car seat must be located and
installed properly during everyday use of the vehicle, to avoid being trapped
by a movable seat or by a vehicle door.
Make sure that all heavy or sharp-edged objects that could cause injury in
case of an accident are secured properly.
Always ensure that the child car seat is secured, even when not in use. A
loose child car seat can cause injury to other passengers in the car during
emergency stop or accident.
Make sure that the straps holding the restraint to the vehicle should be tight
and any straps restraining the child should fit snugly to the child’s body.
Check to make sure that the straps are not twisted.
All passengers in the vehicle must have their seat belts fastened. Any
passenger in the vehicle who are not wearing seat belts may pose danger to
the child in the car seat.
All passengers should be aware of how to release the child from the car seat
in case of danger or an accident. The car seat should be replaced
immediately if it has been subjected to violent shocks in an accident.
Protect the child car seat against intense sunlight when it is not in use. The
metal and plastic parts of the car seat may turn extremely hot under the sun
and this may burn your child.
It is unavoidable that the use of child car seat may cause indentations or
wear marks to certain types of vehicle seat covers.
Do not use any load bearing contact points other than those described in the
instructions and marked in the child restraint.
Make sure that the vehicle seatbelt buckle is not resting on the child seat
frame. If the seat belt buckle lies across the frame of the child car seat, it will
be under pressure and may spring open in an impact. Only seatbelt webbing
should be in contact with the frame of the child car seat.
Infiniti 1/2/3
3
PART LIST & LEGEND
11
1
12
2
20
13
14
3
15
4
16
5
6
7
21
10
17
8
9
18
10
19
2
22
23
24
7
Infiniti 1/2/3
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Harness straps
Velcro fastener
Shoulder pads
Hip straps
Buckle
Crotch strap
Metal retainer
Cushion flap
Band
Support seat cushion
Headrest
Support backrest cushion
Red belt holder
Belt slot
Backrest
Red belt guide
Seat / booster seat
Harness adjuster lever
Harness adjuster strap
Wing
Armrest
Protective flap
Pouch (for user manual)
Harness yoke
ASSEMBLY INSTRUCTIONS
Remove the product from the package.
With the parts lying on flat, join the hooks from
lower part of backrest to the seat.
Rotate backrest along hinge of seat.
Insert the headrest to the backrest.
Infiniti 1/2/3
5
Group 1
9 kg
to
18 kg
For children with body weight from 9 - 18 kg
5-Point Harness with support backrest & seat cushion
Infiniti 1/2/3
6
Group 1
To Loosen the Harness
Press the harness adjuster lever (located
underneath the cover) and pull both
harness straps forward at the same time.
DO NOT pull from the shoulder pads.
Tip: Insert a finger through the hole of
the fabric cover to press.
S
PRES
Infiniti 1/2/3
7
Group 1
To Adjust the Heights of the Harness Straps (Group 1)
Harness straps should be correctly
adjusted for optimal protection to your
child.
Too low
Too high
The harness straps of this child car seat
can be adjusted into 3 different height
positions, depending on the size of the
child. The harness straps must lie at your
child’s shoulder level or slightly above.
Loosen the harness straps as far as
possible. (See “To Loosen the Harness”
section. Page 7)
Open the protective flap at the back of the
seat. Detach the Velcro fastener and
release the harness straps from the
harness yoke.
Do not twist the harness
straps.
Insert both the Velcro fastener and the
harness straps into slots for the correct
height position.
Make sure the Velcro pads are fastened
together tightly, and the harness straps are
returned to the harness yoke. Make sure
that both straps are in the same height
level.
Return and close the protective flap.
Make sure that the headrest adjuster is in
its lowest position.
Infiniti 1/2/3
8
Group 1
To Fit Child Car Seat to the Vehicle Seat (Group 1)
Do not twist the belt in
any way during the whole
installation procedure.
Place the child car seat facing forward on
the vehicle rear seat.
Pull out the whole length of the passenger
seat belt such that the diagonal belt is
threaded through the gap between headrest
and wing of the backseat 1 while the lap
belt is threaded under the armrest 2 .
1
2
Insert both passenger belts with the seat
buckle through the hole of the backrest 3
from one side, enclosing the back and pull
out the belts with the seat buckle from the
other hole 4 to the front.
4
Make sure the belts run on top of the
protective flap of fabric cover.
3
Infiniti 1/2/3
9
Group 1
While holding the buckle, tuck in the
diagonal belt to the red belt guide 5
attached on the other side and thread the
lap belt UNDER the armrest 6 from the
same side. Then, fasten the seat belt until
you hear an audible “CLICK” 7 .
5
7
6
8
Push the car seat back against the vehicle
backrest and simultaneously pull the
diagonal belt upwards to tighten 8 .
Remove any slack in the seat belt.
Check that the child car seat is correctly installed :
The diagonal belt MUST NOT be inserted through the red belt
holder on the headrest. The red belt holder is DESIGNED to
be used during the next stage – Group 2. For Group 1, it
should be passing under the red belt holder and positioned in
the gap between the headrest and the wing of backrest.
The child car seat is securely fastened.
The vehicle seat belt is tightened up and not twisted.
The diagonal seat belt runs between the headrest and the wing on
one side and threaded in the red belt guide on the buckle side.
The lap belt runs UNDER the armrest of both sides.
Infiniti 1/2/3
10
Group 1
To Secure Child (Group 1)
Check that the harness straps are in the
correct height position. If not, see “To
Adjust the Heights of the Harness Straps”
section. (Page 8)
Press red release button on buckle and pull
tongues out of buckle.
Place your child into the child car seat.
Pull the harness straps over the shoulders
of your child.
Do not twist or interchange
the harness straps.
Infiniti 1/2/3
11
Group 1
Join the buckle tongues together and insert
into the buckle until you hear an audible
“CLICK”.
Remove any slack by tightening the
harness. (See next section “To Tighten the
Harness”)
Make sure that the hip straps lie as low as
possible over your child’s hips.
“CLICK”
To Tighten the Harness (Group 1)
Pull harness straps to remove any slack
from the lap section.
Pull the harness adjuster strap until the
harness lies flat and close to the child’s
body.
PU
LL
Important
Check that the harness fits snugly to your
child, so that only one or two fingers can fit
between the harness and the child’s body.
Check that your child is properly secured:
The straps of the child car seat are fitted snugly.
The buckle tongues are engaged in the harness buckle.
The harness straps are adjusted correctly and not twisted.
The hip straps lie as low as possible over your child’s hips.
Infiniti 1/2/3
12
Group 1
Group 2
15 kg
to
25 kg
For children with body weight from 15 - 25 kg
With backrest and booster seat
Convert to Group 2 child car seat only when your child
exceeded the maximum weight limit
Infiniti 1/2/3
13
Group 2
To Remove the 5-Point Harness (Group 2)
Release the child car seat from the
passenger seat belt. Flip over to the back
side of the child car seat.
Open the protective flap at the back of
seat. Detach the Velcro fastener and
release the harness straps from the
harness yoke.
Pull these out of the belt slots and release
the support backrest cushion from the
backrest of the child car seat.
Return and close the protective flap.
Turn the child car seat over and locate the
three metal retainers attached to opposite
ends of the crotch strap and hip straps.
Turn the metal retainers so that the short
side will pass through the slots to the front.
Release all the three metal retainers to
detach the crotch strap and hip straps and
remove the support seat cushion from the
child car seat.
Pull the whole length of harness adjuster
strap to tighten. Fold the strap underneath
the base.
Store away all dismantled component
including the whole set of harness buckle
and the cushions. It is obligatory to reinstall
them should the car seat need to be
re-used as Group 1.
PULL
To reinstall, follow the instructions described above in reverse order.
Infiniti 1/2/3
14
Group 2
To Secure Child (Group 2)
Position the child car seat inside the
vehicle rear seat and place the child in the
child car seat.
Fasten with the vehicle 3-Point passenger
seat belt by first looping the diagonal belt
inside the red belt holder located on the
lower part of the headrest.
Make sure that the belt is fully looped
inside this hole and that the belt is not
twisted in any way.
While holding the buckle, pull the diagonal
belt over the shoulder of your child, and
thread this under the armrest of the buckle
side. Then thread the lap belt under both
armrests.
Fasten the seat belt until you hear an
audible “CLICK”. Pull the belts tight.
DO NOT twist the seat belt in
any way and remove any
slack in the harness.
Infiniti 1/2/3
15
Group 2
To Adjust the Headrest (Group 2)
Slide the headrest up or down to the
correct position according to the size of
your child.
Check that the child is properly secured:
The diagonal belt is looped INSIDE the red belt holder of the headrest
on one side and runs UNDER the armrest on the buckle side.
The lap belt runs UNDER both armrests.
The seat belt is tightened up and not twisted.
The diagonal belt is placed in the middle of the child’s shoulder.
The lap belt should go over the pelvic region, not the stomach.
The top of the child’s head is not higher than the child car seat.
Infiniti 1/2/3
16
Group 2
Group 3
22 kg
to
36 kg
For children with body weight from 22 – 36 kg
Only booster seat
Convert to Group 3 child car seat only when your child
exceeded the maximum weight limit, or the top of their
head is higher than maximum height of the headrest.
Infiniti 1/2/3
17
Group 3
To Remove the Backrest (Group 3)
Unfasten the passenger seat belt and
remove the child car seat.
Fold down and lay flat the backrest.
Release the backrest piece from the hinge
area to remove.
Store away all dismantled components, as it is obligatory to reinstall them
should the car seat need to be re-used as Group 2.
To reinstall, follow the instructions described above in reverse order.
Infiniti 1/2/3
18
Group 3
To Secure Child (Group 3)
Place the booster seat on the vehicle
passenger seat ensuring it is firmly
touching against the vehicle seat.
Place your child on the booster seat.
Fasten with the vehicle 3-Point passenger
seat belt with the diagonal belt resting on
the shoulder of the child and then thread
the diagonal belt over the armrest on the
buckle side.
While holding the buckle, thread the lap
belt under both armrests.
Then, fasten the seat belt until you hear an
audible “CLICK”. Pull the belts tight.
DO NOT twist the belt in any
way and remove any slack in
harness.
Check that the child car seat is correctly installed.
The diagonal seat belt should not go too much over the shoulder and
it should rest over the shoulder, not the neck.
The diagonal belt runs OVER the armrest on the buckle side.
The lap belt runs UNDER both armrests.
The lap belt should go over the pelvic region, not the stomach.
The seat belt is tightened up and not twisted.
Infiniti 1/2/3
19
Group 3
CARE & MAINTENANCE
Check regularly to make sure that all important parts are in good working
condition. Check that all mechanical parts are in normal operation.
Do not use the child car seat if there are any damages found. Any worn out
parts should be replaced before use.
Do not lubricate any parts of the child car seat.
To prevent damage or breakage of this child car seat, make sure it does not
become trapped or loaded by heavy baggage, reclinable seats or slamming
doors.
To prevent damage to the cover, do not remove the logo or instruction labels
sewn to the cover.
Store the child car seat in a safe place when it is not in use. Do not store it
near any direct sunlight or direct heat source.
Avoid placing heavy objects on top of the child car seat.
About Harness Buckle
If you encounter any situations below, this could be malfunction of the buckle
caused by dirt and dust:
The buckle tongues no longer lock into the buckle.
There is no audible “CLICK” when locking the buckle.
The buckle tongues are difficult to insert into the buckle.
The buckle tongues are ejected slowly during unfastening of the buckle.
The buckle is difficult to unfasten unless extreme force is applied.
To Clean the Harness Buckle
Brush away any loose debris using soft bristled brush.
Clean with sponge using warm water and mild soap. Towel dry.
Do not use solvents, harsh cleaning agents or bleach.
To Clean the Plastic Parts
The plastic parts can be cleaned with sponge using soapy water. Do not use
solvents or harsh cleaning agents.
Infiniti 1/2/3
20
Washing Instructions of Fabric Cover
Hand wash using cold water and mild soap.
DO NOT: dry clean, bleach, tumble dry, iron.
Wash inside out.
Line dry away from direct heat or sunlight.
DO NOT use the car seat without the fabric upholstery being
in place.
To Install the 5-Point Harness
Position the support seat cushion to the
seat and the support back cushion to the
backrest. Align the holes on cushion to the
child car seat.
Prepare the 5-Point harness according to
this diagram.
Join the buckle tongues and insert to the
buckle. Lock until you hear an audible
“CLICK”.
Straighten all the straps. Make sure they
are not twisted.
“CLICK”
Loop the shoulder pads through the
harness straps. Check that the curve side
of the shoulder pads are placed facing
outwards with the fabric sides facing up.
Both Velcro fastener straps should be in
upright position.
Infiniti 1/2/3
21
Loop the metal retainer from the crotch
strap through the band on the cushion flap
and insert with the short side into the holes
on the support seat cushion and seat
cover, then into the slot of the seat all the
way through the bottom. Turn the metal
retainer in place to lock in position.
Lift the sides of the support seat cushion
and insert the other two metal retainers
attached to the hip straps into the holes of
the seat cover and the slots on the seat all
the way through the bottom. Turn the metal
retainers in place to lock in position.
Check that all the three metal
retainers are LOCKED in
position by pulling the hip
straps and the vertical strap of
the harness.
Open the protective flap at the back of
seat.
Insert both harness straps with its Velcro
fasteners to the holes on the support
backrest cushion and through the correct
belt slots on the backrest. Make sure that
both straps are inserted in the same level.
Infiniti 1/2/3
22
Attach the Velcro fasteners from the back.
Press the harness adjuster level and pull
up the harness yoke to loosen.
PULL
Loop both ends of the harness straps to
the harness yoke. Check that these are
secured firmly.
Return and close the protective flap.
DO NOT twist the harness
straps.
Please read and follow instructions
thoroughly before re-using as Group 1 car
seat. (Pages 6-12)
Infiniti 1/2/3
23
To Remove the Fabic Cover
Adjust the headrest to a higher position.
Detach the Velcro fasteners near the base
of the headrest.
Remove the headrest cover.
Detach the backrest from the seat in order
to remove the cover.
Turn the child car seat to the back. Open
the protection flap and detach the Velcro
fastener near the top of the backrest.
From the lower edge of the fabric cover,
pull and remove from the hinge side. Then,
pull the whole cover upward through the
headrest side to remove.
Pull and remove the cover of the seat.
To re-fit the fabric cover, reverse the instructions on “To Remove the Fabric
Cover”.
Infiniti 1/2/3
24
WARRANTY
Our products are covered under warranty to the original purchaser for a
period of 24 months for plastic parts, etc. and 12 months for fabric
components and other parts susceptible to wear and tear. The warranty
period is effective from the date of original purchase and proof of original
purchase is required.
It is normal for fabric to discolour from sunlight and to show wear and tear
after a long period of use even when used normally. The warranty period for
the fabric and other parts susceptible to wear, such as harnesses, is therefore
limited to a period of 12 months as of date of purchase.
This warranty is extended only to the original retail purchaser, it is
non-transferable and applies only for non-commercial use.
Warranty does not cover when ECE quality mark and approval number have
been damaged or removed.
If you have recently purchased this product and found it to be defective in
anyway, please contact our Customer Service for assistance.
This LIMITED WARRANTY does not cover any personal injuries, damage to,
or, failure of the product or any other losses due to accident, abuse, misuse,
alteration, neglect, normal wear and tear, improper assembly, improper fit,
improper loads (including passenger weight over the design limits), improper
maintenance, unauthorized repairs or use of unauthorized replacement parts
not designed for the product.
In no event will Grow’n Up Limited, or the retailer selling this product, be liable
for any damages, including incidental or consequential damages, arising out
of the use or inability to use this product.
PRODUCT REGISTRATION
In order to properly register your child restraint system, you will need
to provide the model number, batch number and date of
manufacture. This information is permanent located at bottom of the
booster seat.
Please go to
www.cozibeebi.com
to register your product.
Model: 7003
E4
Infiniti 1/2/3
25
ECE R44/04
04443913
CUSTOMER SERVICE
USA and Canada:
service@grow-n-up.com
Toll free hotline:
1-888-GNU-9898
Other countries:
support@grow-n-up.com
www.cozibeebi.com
Cozi Beebi ® is a trademark
of Grow’n Up Ltd. © 2010
Grow’n Up Ltd. All rights
reserved.
Tsim Sha Tsui East,
Kowloon, Hong Kong.
MADE IN CHINA.
Download PDF