E-line | IPC-HF3200 Series | User`s manual | E-line IPC-HF3200 Series User`s manual

Megapixel Indoor IP Camera User’s Manual
Version 3.5.0
eLineTechnology.com
Welcome
Thank you for purchasing our IP camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!
i
eLineTechnology.com
Important Safeguards and Warnings
1.Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1.
Before you replace the SD card, please unplug the power cable and then remove the shell
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2.Installation
Do not apply power to the IP camera before completing installation.
Do not put object on the IP camera.
3.Environment
This series IP camera should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
The working temperature ranges from -10℃ to +60℃. Please keep it away from the electromagnetic
radiation object and environment.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the IPC.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.
4. Daily Maintenance
Current series IPC has no power button. Please unplug all corresponding power cables before your
installation.
Do not touch the CCD or CMOS part; you can use the blower to clean the dust on the surface of the
lens. You can use the dry cloth with some alcohol to clear if necessary.
Please keep the dustproof cap back to protect the CCD or CMOS part if the IP camera does not work
for a long time.
If there is too much dust on the housing, please use the water to dilute the mild detergent first and then
use it to clean the device with the clear dry cloth. Finally use the dry cloth to clean the device.
5. Accessories
Please open the accessory bag to check the items one by one in accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged in the bag.
Accessory Name
Amount
IPC Unit
■
1
C/CS adapter
■
1
ii
eLineTechnology.com
Quick
Guide
CD
Start
■
1
■
1
iii
eLineTechnology.com
Table of Contents
1
General Introduction ..................................................................................................................1
1.1
Overview ........................................................................................................................1
1.2
Feature...........................................................................................................................1
1.3
Specifications ................................................................................................................2
1.3.1 Performance...........................................................................................................2
1.3.2 Factory Default Setup ...........................................................................................4
2
Framework.................................................................................................................................13
2.1
Rear Panel...................................................................................................................13
2.2
Side Panel ...................................................................................................................17
2.3
Front Panel ..................................................................................................................17
2.4
Bidirectional talk .........................................................................................................18
2.4.1 Device-end to PC-end ........................................................................................18
2.4.2 PC-end to the Device-end..................................................................................18
2.5
Alarm Setup.................................................................................................................19
2.5.1 Alarm Input and Output Connection.................................................................19
2.5.2 IR Light Connection ............................................................................................20
3
Installation .................................................................................................................................21
3.1
Lens Installation..........................................................................................................21
3.1.1 Auto Aperture Lens .............................................................................................21
3.1.2 Manual Lens.........................................................................................................21
3.1.3 Remove Lens .......................................................................................................22
3.2
SD Card .......................................................................................................................22
3.2.1 Installation ............................................................................................................22
3.2.2 Remove.................................................................................................................23
3.3
3G Card .......................................................................................................................23
3.3.1 Installation ............................................................................................................23
3.3.2 Remove.................................................................................................................24
3.4
3G/WIFI Antenna........................................................................................................25
iv
eLineTechnology.com
3.4.1 Installation ............................................................................................................25
3.4.2 Remove.................................................................................................................25
3.5
4
5
6
I/O Port.........................................................................................................................26
Quick Configuration Tool.........................................................................................................28
4.1
Overview ......................................................................................................................28
4.2
Operation .....................................................................................................................28
Web Operation..........................................................................................................................31
5.1
Network Connection...................................................................................................31
5.2
Login and Logout........................................................................................................31
FAQ ............................................................................................................................................34
Appendix Toxic or Hazardous Materials or Elements ...............................................................35
v
eLineTechnology.com
1 General Introduction
1.1 Overview
This series IP camera integrates the traditional camera and network video technology. It adopts
audio video data collection, transmission, storage together. It can connect to the network directly
without any auxiliary device.
This series IPC uses standard H.264 video compression technology and PCM, G.711a/u audio
compression technology, which maximally guarantees the audio and video quality.
This series IPC has mega pixel resolution and supports 12V DC/24V AC power. It supports the
wireless network application, bidirectional talk, digital water mark and etc.
It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its high definition, multiple functions and
various applications, this series IPC is widely used in many indoor environments and other
important area surveillance.
1.2 Feature
User
Management
Data
Transmission
Storage
Function
z
z
Different user rights for each group, one user belongs to one group.
The user right can not exceed the group right.
z
z
Support cable network data transmission via Ethernet
Wireless device supports WIFI/3G wireless data transmission.
z
z
z
z
Support central server backup function in accordance with your configuration and
setup in alarm or schedule setting
Support record via Web and the recorded file are storage in the client-end PC.
Support local SD card hot swap. Support short-time storage when encounter
disconnection.
Support network storage such as FTP.
Real-time respond to external on-off alarm input, and video detect as user predefined activation setup and generate corresponding message in screen and audio
prompt(allow user to pre-record audio file)
Real-time video detect: motion detect, camera masking.
IPC supports one-channel audio/video data transmit to network terminal and then
decode. Delay is within 270ms (network bandwidth support needed)
Max supports 20 connections.
Adopt the following audio and video transmission protocol: HTTP, TCP, UDP,
MULTICAST, RTP/RTCP, RTSP and etc.
Support web access.
Realize IPC configuration and management via Ethernet.
Support device management via web.
Support various network protocols.
Support peripheral equipment connection via the RS232 port, each peripheral
equipment control protocol and interface can be set freely.
Support serial port (RS232/RS485) transparent data transmission.
Support the on-off alarm device to alarm via the sound or the light.
External power adapter. Support DC 12V/AC 24V power supply.
z
z
Support Power over Ethernet (PoE). Conform to the IEEE802.3af standard.
Connect the device to the switcher or the router that supports the PoE function to
z
z
z
z
Alarm
Function
z
z
Network
Monitor
z
z
Network
Management
z
z
z
z
z
Peripheral
Equipment
Power
PoE
eLineTechnology.com
1
z
z
z
z
Assistant
Function
z
z
z
z
z
realize the network power supply.
To guarantee proper performance, please make sure the power sourcing device
can supply at least 10W power.
Usually, do not use the PoE for the WIFI/3G device.
Day/Night mode auto switch (ICR switch.)
Backlight compensation: screen auto split to realize backlight compensation to
adjust the bright.
Support system resource information and running status real-time display. Support
log function.
Support video watermark function to avoid vicious video modification.
Support auto aperture.
Support picture parameter setup such as electronic shutter and gain setup.
Support dual-stream, ACF(Active frame control )
1.3 Specifications
1.3.1 Performance
System
Please refer to the following sheet for IPC performance specification.
Model
IPC-HF3500
IPC-HF3300
IPC-HF3200
IPC-HF3100
IPC-HF3110
Parameter
Series
Series
Series
Series
Series
Main
TI Davinci high performance DSP
Processor
OS
Embedded LINUX
System
Support real-time network, local record, and remote operation at the same
Resources
time.
User Interface Remote operation interface such as WEB, DSS, PSS
System Status SD card status, bit stream statistics, log, and software version.
1/2.5-inch
1/2.8-inch
1/2.9-inch
1/3-inch
Image Sensor
1/3-inch CCD
CMOS
CMOS
CMOS
CMOS
2560(H)*192
2080(H)*155
1920(H)*120
1280(H)*960( 1280(H)*960(
Pixel
0(V)
3(V)
0(V)
V)
V)
Day/Night
Support day/night mode switch and IR-CUT at the same time.
Mode
Auto Aperture Optional
Gain Control
Fixed/Auto
Video Parameter
White Balance
On/off
BLC
On/off
Electronic
Shutter
Manual/Auto
PAL: It ranges from 1/3 to 1/10000.
NTSC: It ranges from 1/4 to 1/10000.
Manual/Auto
PAL: It
ranges from
1/3 to
1/100000.
NTSC: It
ranges from
1/3 to
1/100000.
H.264/H.264B/MJPEG
Video
Compression
Standard
eLineTechnology.com
2
Video Frame
Rate
PAL:
Main
stream
(2560*1920
@8fps)
Extra
stream(704*5
76@8fps)
Main stream
(1920*1080
@25fps)
Extra stream
(704*576@2
5fps)
PAL:
Main
stream
(2048*1536
@15fps)
Extra
stream(704*5
76@15fps)
Main stream
(1920*1080
@25fps)
Extra stream
(704*576@2
5fps)
PAL:
Main
stream
( 1920*1080
@25fps)
extra stream
( 704*576
@25fps)
PAL:
Main
stream
( 1280*960
@25fps),
extra stream,
( 704*576@
25fps)
NTSC:Main
stream
(2560*1920
@8fps)
Extra stream
(704*480@8f
ps)
Main stream
(1920*1080
@30fps)
Extra stream
(704*480@3
0fps)
NTSC:Main
stream
(2048*1536
@15fps)
Extra stream
(704*480@1
5fps)
Main stream
(1920*1080
@30fps)Extra
stream
(704*480@3
0fps)
NTSC : Main
stream
(1920*1080
@30fps)
Extra stream
(704*480@3
0fps)
NTSC : Main
stream
(1280*960@
30fps)
Extra stream
(704*480@3
0fps)
Audio
Video Bit Rate
H.264: 56Kbps-8192Kbps.
MJPEG is adjustable and bit rate is adjustable.
Support customized setup.
Flip
Support
Mirror
Snapshot
Privacy Mask
Video Setup
Video
Information
Lens
Lens Interface
Audio Input
Audio Output
Bidirectional
Talk Input
Audio Bit Rate
Audio
Compression
Standard
Support
Max 1f/s snapshot. File extension name is JPEG
Each channel supports max 4 privacy mask zones
Support parameter setup such as bright, contrast.
Video
Motion Detect
Camera
Masking
PAL:
Main
stream
( 1280*960
@12.5fps )
,
extra stream,
( 704*576@
12.5fps)
Main stream
( 1280*720
@25fps ),
extra stream
(704*576@2
5fps)
NTSC:Main
stream
(1280*960@
12.5fps)Extra
stream
(704*480@1
2.5fps)
Main stream
(1280*720@
30fps)
Extra stream
(704*480@3
0fps)
Channel title, time title, motion detect, privacy mask.
Optional
C/CS optional
1-channel, 3.5mm JACK LINE IN
1-channel, 3.5mm JACK SPEAK OUT
Reuse the first audio input channel
16kbps 16bit
G.711A/G.711Mu/PCM
396 (18*22) detection zones;sensitivity level ranges from 1 to 6 (The 6th
level has the highest sensitivity)
Activation event, alarm device, audio/video storage, image snapshot, log,
email function and etc.
Sensitivity level ranges from 1 to 6. Each sensitivity level is the percentage of
the privacy mask zone.
eLineTechnology.com
3
Alarm Input
Activation event, alarm device, audio/video storage, image snapshot, log,
email SMTP function and etc.
1-channel input,1-channel output
Record and
Backup
Network
AUX Interface
Record
Priority
Manual>External alarm >Video detect>Schedule
Local Storage
Support local SD card hot swap
Storage
Management
Support display local storage status
Wire Network
Network
Protocol
Remote
Operation
Video Output
Network
Interface
1-channel wire Ethernet port, 10/100 Base-T Ethernet
Standard HTTP, TCP/IP, ARP, IGMP, ICMP, RTSP, RTP, UDP, RTCP, SMTP,
FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour, SNMP.
Monitor, PTZ control, system setup, file download, log information,
maintenance , upgrade and etc
1-channel analog video output,BNC port
1-channel Ethernet, 10/100 Base-T Ethernet (The IPC-HF3110-F series
product has the optical port.)
Support 3G SIM card, TD/EVDO/WCDMA function. (For 3G series product
only.)
Support to receive the wireless signal (This function is for 3G and WIFI series
product only.)
3G Port
Antenna Port
General Parameter
RS485 port
PTZ control interface. Support various protocols.
Power
Support AC24V/DC12V power and PoE. (The IPC-HF3110-F/W/E/T/C series
product does not support the PoE function.)
Power
Consumption
Working
Temperature
Working
Humidify
Dimensions
Weight
Installation
<10W (For WIFI and 3G device, it is below 12W.)
-10℃~+60℃ (For –W device, it is from -10℃~+55℃. For 3G device, it is from 10℃~+50℃ )
10%~90%
70*63.2*149.5
650g
Support various installation modes(Enclosure and bracket is optional)
1.3.2 Factory Default Setup
Please refer to the following sheet for factory default setup information.
Default Setup
Item
IPCHF3500
Series
Camera
Brightness
50
Contrast
50
Hue
50
Saturation
50
Exposure Mode
Auto
Gain Scope
0~80
Conditions
Setup
eLineTechnology.com
IPCHF3300
Series
IPCHF3200
Series
IPCHF3100
Series
IPCHF3110
Series
4
Default Setup
Setup
Item
IPCHF3500
Series
Auto Iris
On
Profile
Auto
Day&Night
Auto
Backlight
Off
Mirror
Off
Flip
Off
Video bit stream
Video
Main
Stream
Sub
Stream
Snapshot
eLineTechnology.com
IPCHF3300
Series
Bit stream
type
General
Encode
mode
H.264
Resolution
1080P(1920*1080)
Frame
Rate
(FPS)
PAL: 25
NTSC:30
Bit Rate
Type
CBR
Recommen
ded Bit
3584-8192 Kb/S
Bit Rate
8192
I Frame
50
Watermark
Enable
Watermark
character
DigitalCCTV
Enable
Enable
Bit stream
type
General
Encode
mode
H.264B
Resolution
CIF(352*288/352*240)
Frame
Rate
(FPS)
PAL: 25
NTSC:30
Bit Rate
Type
CBR
Recommen
ded Bit
192-1024Kb/S
Bit Rate
1024
I Frame
50
Snapshot
Type
General
Image
Size
1080P(1920*1080)
Quality
5
IPCHF3200
Series
IPCHF3100
Series
IPCHF3110
Series
720P(1280*720)
720P(1280*720)
5
Default Setup
Setup
IPCHF3500
Series
Item
Video Overlay
Path
Audio
Main Stream
Sub Stream
Network
TCP/IP
Connection
eLineTechnology.com
Interval
1s
Privacy
Mask
Disable
Channel
Title
Enable
Time Title
Enable
IPCHF3300
Series
IPCHF3200
Series
IPCHF3100
Series
IPCHF3110
Series
Snapshot
Path
C:\PictureDownload
Record
Path
C:\RecordDownload
Enable
Enable
Encode
Mode
G.711A
Enable
Disable
Encode
Mode
G.711A
Host Name
IPC
Ethernet
Card
Wire(Default)
Mode
Static
Mac
Address
Device MAC address when it is shipped out of the factory
IP Version
IPV4
IP Address
192.168.1.108
Subnet
Mask
255.255.255.0
Default
Gateway
192.168.1.1
Preferred
DNS
8.8.8.8
Alternate
DNS
8.8.8.8
Enable
ARP/Ping
set device
IP address
service
Enable
Max
Connection
10
TCP Port
37777
UDP Port
37778
HTTP Port
80
6
Default Setup
Setup
IPCHF3500
Series
Item
PPPoE
DDNS
IP Filter
SMTP(Email)
eLineTechnology.com
IPCHF3300
Series
IPCHF3200
Series
RTSP Port
554
HTTPs
Port
443
Enable
Disable
Username
N/A
Password
N/A
Server
Type
Disable,CN99 DDNS
Server IP
none
Server Port
80
Domain
Name
none
User
none
Password
N/A
Update
Period
10 minutes
Trusted
sites
Disable
SMTP
Server
none
Port
25
Anonymity
Disable
User Name
anonymity
Password
N/A
Sender
none
Authenticat
ion
(Encryption
mode)
N/A
Title
(Subject)
IPC Message
Attachment
Enable
Mail
Receiver
N/A
Send
Interval
0 second
Email Test
Disable,interval=60 minutes
IPCHF3100
Series
IPCHF3110
Series
7
Default Setup
Setup
IPCHF3500
Series
Item
UPnP
SNMP
Bonjour
Multicast
QoS
Video detect
Event
Motion Detect
eLineTechnology.com
IPCHF3300
Series
IPCHF3200
Series
Enable
UPnP
Disable
SNMP v1
Disable
SNMP v2
Disable
SNMP Port
161
Read
Community
public
Write
Community
private
Trap
Address
N/A
Trap Port
162
SNMP
v3 disable
Enable
Enable
Server
Name
“SN”. It depends on the device.
Multicast
Address
239.255.42.42
Port
36666
Real-time
Monitor
0
Command
0
Wireless
Qos
Disable
Enable
Disable
Anti-dither
5 seconds
Sensitivity
3
Record
Channel
Enable
Record
Delay
10 seconds
Relay out
Enable
Alarm
Delay
10 seconds
Send Email
Disable
PTZ
Disable
Activation
Operation
N/A
Address
0
Snapshot
Disable
IPCHF3100
Series
IPCHF3110
Series
8
Default Setup
Setup
IPCHF3500
Series
Item
Video
Masking
Alarm
Alarm
Activation
Enable
Disable
Record
Channel
Enable
Record
Delay
10 seconds
Relay out
Enable
Record
Delay
10 seconds
Send Email
Disable
PTZ
Disable
Activation
Operation
N/A
Address
0
Snapshot
Disable
Enable
Disable
Relay in
Alarm 1
Anti-dither
0 seconds
Sensor
Type
NO
Record
Channel
Enable
Record
Delay
10 seconds
Relay out
Enable
Alarm
Delay
10 seconds
Send Email
Disable
PTZ
Disable
Activation
Operation
N/A
Address
0
Snapshot
Disable
Relay output
Abnormity
No SD Card
Capacity
Warning
eLineTechnology.com
IPCHF3300
Series
IPCHF3200
Series
IPCHF3100
Series
IPCHF3110
Series
1
Enable
Disable
Relay out
Enable
Relay
Delay
10 seconds
out
Send email
Disable
Enable
Disable
Capacity
Limit
10%
9
Default Setup
Setup
IPCHF3500
Series
Item
SD
Error
Card
Disconnectio
n
IP Conflict
Period
Setup
Storage
Storage
FTP
Record Control
eLineTechnology.com
Relay out
Enable
Relay
Delay
10 seconds
out
Send Email
Disable
Enable
Disable
Relay out
Enable
Relay
Delay
10 seconds
out
Send email
Disable
Enable
Disable
Record
Enable
Record
Delay
10 seconds
Relay out
Enable
Relay
Delay
10 seconds
out
Enable
Disable
Record
Enable
Record
Delay
10 seconds
Relay out
Enable
Relay
Delay
10 seconds
out
IPCHF3300
Series
Week
Enable
Time
00:00:00 to 24:00:00
Schedule
Disable
Motion
Detect
Enable
Alarm
Enable
Enable
FTP
Disable
Server IP
N/A
Port
21
Username
anonymous
Password
N/A
Remote
path
share
Emergency
(Local)
Disable
Pack
Duration
8 minutes
IPCHF3200
Series
IPCHF3100
Series
IPCHF3110
Series
10
Default Setup
Setup
IPCHF3500
Series
Item
General
System
Local Host
Date
time
and
PTZ
Auto Maintenance
eLineTechnology.com
IPCHF3300
Series
IPCHF3200
Series
IPCHF3100
Series
Pre-record
5 seconds
Disk Full
Overwrite
Record
Mode
Auto
Record
Stream
Main Stream
Device No
Device factory SN
Language
English
Video
Standard
PAL
Date
Format
Y-M-D
Time
Format
24H
Time Zone
GMT+08:00
System
Time
Sync PC
DST
Disable
DST Type
Week
Start Time
00:00:00 of the first Sunday of the month
End Time
00:00:00 of the second Monday of the month
NTP
Disable
NTP
Server
clock.isc.org
Port
37
Update
Period
10 minutes
Protocol
PELCOD
Address
1
Baud Rate
9600
Data Bit
8
Stop bit
1
Parity
N/A
Auto
Reboot
Enable 02:00 each day.
Auto
Delete Old
Files
Disable
IPCHF3110
Series
11
Default Setup
Setup
IPCHF3500
Series
Item
System Log
eLineTechnology.com
IPCHF3300
Series
End Time
Current time
Start Time
The previous day
All Types
Select all
IPCHF3200
Series
IPCHF3100
Series
IPCHF3110
Series
12
2 Framework
2.1 Rear Panel
This series IP camera real panel is shown as below. See Figure 2-1.
The rear panel with the network port
The rear panel with the 100M fiber port
Figure 2-1
Please refer to the following sheet for detail information.
Interface Name
VIDEO OUT
Video output port
Connector
Function
BNC
Output analog video
signal. Can connect to
eLineTechnology.com
13
TV monitor to view
video.
AC 24V/ DC 12V
Power port
z
Power port.
z
Input 12V DC or
AC 24V
STATUS
z
Red light
Indication Light
System boot upred light is on
z
System
upgrades-red light
flashes
z
System resetsred light flashes.
z
Green light
Normal working
status-green light
is on.
z
Display record
status: Recordgreen light
flashes.
z
Yellow light
Detect the
wireless deviceyellow light is on.
3G
Connect to 3G card.
Please note it is for
3G series product
only.
WIFI
Antenna port
Connect to 3G/WIFI
antenna to receive the
wireless signal.
Please note this
function is for some
series products only.
IN
Alarm input port
I/O port
Alarm input port 1. To
receive the signal from
eLineTechnology.com
14
the external alarm
device.
NO
Alarm output port
Alarm output port. To
output alarm signal to
C
the alarm device.
z
NO: Normal open
alarm output end.
z
C: Alarm output
public end.
G
GND
Alarm input ground
end.
A
RS485_A port, control
RS485 port
external PTZ
B
RS485_B port, control
external PTZ
RX
RS232_RX,RS232
RS232 port
receive end.
TX
RS232_TX,RS232
COM send out end.
G
GND
RS232 ground end
NA
IR light port
External IR light signal
control port.
RESET
RESET button
Restore factory default
setup.
When system is
running normally,
press the RESET
button for at least 5
seconds, system can
restore factory default
setup.
AUDIO OUT
Audio output port
Audio output 3.5mm
Output audio signal to
JACK port.
the passive device
such as earphone.
AUDIO IN
eLineTechnology.com
Audio input port
Audio input 3.5mm
Input audio signal
15
JACK port.
from devices such as
pick-up.
LAN
Network port
Ethernet port
z
Connect to
standard Ethernet
cable.
z
Support PoE
function.
OPT
100M fiber port
155M single fiber
Transmit 100M
dual-direction SFP
Ethernet data.
fiber module
SD
SD card port
Connect to SD card.
Note
z
When you install
the SD card,
please make sure
current card is not
in write mode and
then you can
install it to the
camera.
z
When you
remove the SD
card, please
make sure current
card is not in write
mode. Otherwise
it may result in
data loss or card
damage.
z
Before hot swap,
please stop
record operation.
eLineTechnology.com
16
GND
Please make sure the
device is securely
earthed to prevent the
thunderstorm strike.
2.2 Side Panel
Please refer to the following interface for side panel dimension information. The unit is mm. See
Figure 2-2.
Figure 2-2
2.3 Front Panel
Please refer to the following interface for the front panel information. The unit is mm. See Figure
2-3.
eLineTechnology.com
17
Figure 2-3
2.4 Bidirectional talk
2.4.1 Device-end to PC-end
Device Connection
Please connect the speaker or the MIC to the audio input port in the device rear panel. Then
connect the earphone to the audio output port in the PC.
Login the Web and then click the Audio button to enable the bidirectional talk function.
You can see the button becomes orange after you enabled the audio talk function.
Click Audio button again to stop the bidirectional talk function.
Listening Operation
At the device end, speak via the speaker or the pickup, and then you can get the audio from the
earphone or sound box at the pc-end.
2.4.2 PC-end to the Device-end
Device Connection
Connect the speaker or the MIC to the audio input port in the PC and then connect the earphone
to the audio output port in the device rear panel.
Login the Web and then click the Audio button to enable the bidirectional talk function.
You can see the button becomes orange after you enabled the audio talk function.
Click Audio button again to stop the bidirectional talk function.
Please note the listening operation is null during the bidirectional talk process.
Listening Operation
At the PC-end, speak via the speaker or the pickup, and then you can get the audio from the
earphone or sound box at the device-end.
eLineTechnology.com
18
2.5 Alarm Setup
The alarm setup interface is shown as below. See Figure 2-4.
z Connect the alarm input device to the alarm input port.
z Connect the alarm output device to the alarm output port and alarm output public port. The
alarm output port supports NO (normal open) alarm device only.
z Open the Web, go to the Figure 2-4. Here you can set the alarm input setup and alarm
output setup. Please set the alarm in for the alarm input in the rear panel. Then you can
select the corresponding type (NO/NC) according to the high/low level type when an alarm
occurs.
z Set the WEB alarm output. The alarm output 01 is the alarm output port of the device rear
panel.
Figure 2-4
2.5.1 Alarm Input and Output Connection
Please refer to the following figure for alarm input information. See Figure 2-5.
Alarm input: When the input signal is idle or grounded, the device can collect the different
statuses of the alarm input port. When the input signal is connected to the 5V or is idle, the
device collects the logic “1”. When the input signal is grounded, the device collects the logic “0”.
Figure 2-5
Please refer to the following figure for alarm output information. See Figure 2-6.
Port NO and Port C composes an on-off button to provide the alarm output.
If the type is NO, this button is normal open. The button becomes on when there is an alarm
output.
eLineTechnology.com
19
If the type is NC, this button is normal off. The button becomes off when there is an alarm output.
Figure 2-6
2.5.2 IR Light Connection
Please refer to the following figure for external IR light information. See Figure 2-7.
IR synchronization input signal. When the external IR light is on, the signal cable from the board
outputs the 3.3V/1mA. It outputs the 0V when the IR light is off.
Figure 2-7
eLineTechnology.com
20
3 Installation
3.1 Lens Installation
3.1.1 Auto Aperture Lens
Please follow the steps listed below for auto aperture lens installation. The interface is shown as
in Figure 3-1 and Figure 3-2.
z Remove the CCD protection cap of the device, and then line up the lens to the proper
installation position. Turn clockwise until the lens is fixed firmly.
z Insert the lens cable socket to the auto lens connector in the side panel.
Figure 3-1
3.1.2 Manual Lens
Install C type lens
z Remove the CCD protection cap from the device.
z Install the C/CS adapter to the camera. Turn clockwise to secure against the focusing ring
firmly.
z Line up the C lens to the installation position of the C/CS adapter. Turn clockwise to fix the
lens.
z Use slotted screwdriver to fasten the screw near the focusing ring and then turn counter
clockwise to move the focusing ring out for several millimeters. Now you can focus manually
and check the video is clear or not. If you can not see the clear video, you can adjust via the
flange-back.
z After you completed the focus setup, use the slotted screwdriver to fix the screw firmly.
Fasten the focusing ring. Now the installation completed.
Install CS type lens
z Remove the CCD protection cap from the device.
z Line up the CS lens to the lens installation position of camera focusing ring. Turn clockwise
to fix the lens.
z Use slotted screwdriver to fasten the screw near the focusing ring and then turn counter
clockwise to move the focusing ring out for several millimeters. Now you can focus manually
and check the video is clear or not. If you can not see the clear video, you can adjust via the
flange-back.
z After you completed the focus setup, use the slotted screwdriver to fix the screw firmly.
Fasten the focusing ring. Now the installation completed.
eLineTechnology.com
21
Figure 3-2
3.1.3 Remove Lens
Please follow the steps listed below to remove lens. The interface is shown as in Figure 3-3.
z Turn the lens counter clockwise and then remove it from the camera.
z Unplug the auto lens cable socket from the auto lens connector. If you are using the manual
aperture lens, please skip to the following step.
z If there is no lens, please put the CCD protection cap back to protect the CCD.
Figure 3-3
3.2 SD Card
3.2.1 Installation
Please follow the steps listed below to install SD card. The interface is shown as in Figure 3-4
and Figure 3-5.
z Use the screwdriver to loosen the SD card protection screw in the rear panel, and then
remove the SD card protection cap from the camera.
z Install the SD card to the camera according to the proper installation position.
z Put the SD card protection cap back.
z Use the screwdriver to fix the SD card protection cap screw firmly to secure the SD card
protection cap in the camera.
eLineTechnology.com
22
Figure 3-4
Figure 3-5
3.2.2 Remove
Please follow the steps listed below to remove SD card. The interface is shown as Figure 3-6.
z Use the screwdriver to loosen the screw of SD card protection cap in the rear panel.
Remove the cap from the camera.
z Follow the SD card direction to remove the SD card.
z Insert the SD card protection cap.
z Use the screwdriver to fix the screw to secure the protection cap.
Figure 3-6
3.3 3G Card
3.3.1 Installation
The 3G card installation is the same with the SD card.
Please follow the steps listed below to install 3G card. The interfaces are shown as Figure 3-7
and Figure 3-8.
eLineTechnology.com
23
z
z
z
z
Use the screwdriver to loosen the 3G card protection cap screw in the side panel, and then
remove the 3G card protection cap from the camera.
Install the 3G card to the camera according to the proper installation position.
Put the 3G card protection cap back.
Use the screwdriver to fix the 3G card protection cap screw firmly to secure the 3G card
protection cap.
Figure 3-7
Figure 3-8
3.3.2 Remove
Please follow the steps listed below to remove 3G card. The interface is shown as Figure 3-9.
z Use the screwdriver to loosen the screw of 3G card protection cap in the rear panel.
Remove the cap from the camera.
z Follow the 3G card direction to remove the 3G card.
z Insert the 3G card protection cap.
z Use the screwdriver to fix the screw to secure the protection cap.
Figure 3-9
eLineTechnology.com
24
3.4 3G/WIFI Antenna
3.4.1 Installation
Line up the thread of the screw of the 3G/WIFI antenna to the thread of the rear panel. See
Figure 3-10.
Please turn according to the direction in the following figure until antenna is secure firmly. See
Figure 3-11.
Figure 3-10
Figure 3-11
After you fix the 3G/WIFI antenna to the WIFI port of the rear panel, you can adjust the antenna
direction. See Figure 3-12.
Figure 3-12
3.4.2 Remove
eLineTechnology.com
25
Use your hands to hold the 3G/WIFI thread end and then turn according to the following figure.
See Figure 3-13.
Now you can see the antenna is away from the thread. See Figure 3-14.
Figure 3-13
Figure 3-14
Remove the 3G/WIFI antenna from the port of the rear panel. See Figure 3-15.
Figure 3-15
3.5 I/O Port
Install Cable
Please follow the steps listed below to install the cable. See Figure 3-16.
eLineTechnology.com
26
Use the small slotted screwdriver to press the corresponding button of cable groove. Insert the
cable into the groove and then release the screwdriver.
Remove Cable
Please follow the steps listed below to remove the cable.
Use the small slotted screwdriver to press the corresponding button of cable groove. Remove the
cable out of the groove and then release the screwdriver.
Figure 3-16
eLineTechnology.com
27
4 Quick Configuration Tool
4.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same time, you
can use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.
4.2 Operation
Double click the “ConfigTools.exe”icon, you can see an interface is shown as in Figure 4-1.
In the device list interface, you can view device IP address, port number, subnet mask, default
gateway, MAC address and etc.
Figure 4-1
Select one IP address and then right click mouse, you can see an interface is shown as in Figure
4-2.
Figure 4-2
eLineTechnology.com
28
Select the “Open Device Web” item; you can go to the corresponding web login interface. See
Figure 4-3.
Figure 4-3
If you want to modify the device IP address without logging in the device web interface, you can
go to the configuration tool main interface to set.
In the configuration tool search interface (Figure 4-1), please select a device IP address and then
double click it to open the login interface. Or you can select an IP address and then click the
Login button to go to the login interface. See Figure 4-4.
In Figure 4-4, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP port in
Web Network interface. Otherwise, you can not login the device.
If you are use device background upgrade port 3800 to login, other setups are all invalid.
Figure 4-4
After you logged in, the configuration tool main interface is shown as below. See Figure 4-5.
eLineTechnology.com
29
Figure 4-5
For detailed information and operation instruction of the quick configuration tool, please
refer to the Quick Configuration Tool User’s Manual included in the resources CD.
eLineTechnology.com
30
5 Web Operation
This series IPC product support the Web access and management via PC.
Web includes several modules: monitor channel preview, PTZ control, system configuration,
alarm and etc.
5.1 Network Connection
Please follow the steps listed below for network connection.
z Make sure the IPC has connected to the network properly.
z Please set the IP address, subnet mask and gateway of the PC and the IPC respectively.
IPC default IP address is 192.168.1.108. Subnet mask is 255.255.255.0. Gateway is
192.168.1.1.
z Use order ping ***.***.***.***(* IP camera address) to check connection is OK or not.
5.2 Login and Logout
Open IE and input IP camera address in the address bar.
For example, if your camera IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE
address bar. See Figure 5-1.
Input your IP
address here
Figure 5-1
The login interface is shown as below. See Figure 5-2.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.
eLineTechnology.com
31
Figure 5-2
If it is your first time to login in, system pops up warning information to ask you whether install
control webrec.cab or not after you logged in for one minute. Please click OK button, system can
automatically install the control. When system is upgrading, it can overwrite the previous Web too.
If you can’t download the ActiveX file, please check whether you have installed the plug-in to
disable the control download. Or you can lower the IE security level. See Figure 5-3.
Figure 5-3
After you logged in, you can see the main window. See Figure 5-4.
eLineTechnology.com
32
Figure 5-4
Please refer to the Web Operation Manual included in the resource CD for detailed operation
instruction.
eLineTechnology.com
33
6 FAQ
Bug
I can not boot up
the device or can
not control the
device.
Please click RESET button for at least five seconds to restore
factory default setup.
SD card hot swap
Before draw out SD card, please stop record or snapshot first and
then wait for at least 15 seconds to remove the SD card. All the
operations before is to maintain data integrity. Otherwise you can
lose all the data in the SD card!
SD
card
times
Do not set the SD card as the storage media to storage the
schedule record file. It may damage the SD card duration.
write
I can not use the
disk as the storage
media.
When disk information is shown as hibernation or capacity is 0,
please format it first (Via Web).
I can not upgrade
the
device
via
network.
The status indication light is shown as red when network upgrade
operation failed. You can use port 3800 to continue upgrade.
Recommended SD
card brand
Kingston 4GB, Kingston 16GB, Kingston32GB, Transcend 16GB,
SanDisk 4GB, SanDisk 32GB.
Usually we recommend the 4GB (or higher) high speed card in case
the slow speed results in data loss.
Audio function
eLineTechnology.com
Please use active device for the audio monitor input, otherwise there
is no audio in the client-end.
34
Appendix Toxic or Hazardous Materials or Elements
Component Name
Toxic or Hazardous Materials or Elements
Pb
Hg
Cd
Cr VI
PBB
PBDE
Circuit Board Component
○
○
○
○
○
○
Device Construction Material
○
○
○
○
○
○
Wire and Cable
○
○
○
○
○
○
Power Adapter
○
○
○
○
○
○
Packing Components
○
○
○
○
○
○
Accessories
○
○
○
○
○
○
O: Indicates that the concentration of the hazardous substance in all homogeneous materials in
the parts is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all
homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006
standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous
substance or elements contained in products will not leak or mutate so that the use of these
(substances or elements) will not result in any severe environmental pollution, any bodily injury or
damage to any assets. The consumer is not authorized to process such kind of substances or
elements, please return to the corresponding local authorities to process according to your local
government statutes.
Note
z
This user’s manual is for reference only.
z
Slight difference may be found in user interface.
z
All the designs and software here are subject to change without prior written notice.
z
If there is any uncertainty or controversy, please refer to the final explanation of us.
z
Please visit our website for more information.
eLineTechnology.com
35
Download PDF