Delta | 100 Series | Installation manual | Delta 100 Series Installation manual

IQ 100 Series (130/140/150)
Meter User & Installation Manual
IM02601003E
Rev F
Copyright (c) 2011 by Eaton Corporation. All rights reserved.
Specifications contained herein are subject to change without notice.
Power Xpert and PowerVision are registered trademarks of Eaton
Corporation.
EATON CORPORATION - CONFIDENTIAL AND PROPRIETARY
NOTICE TO PERSONS RECEIVING THIS DOCUMENT AND/OR TECHNICAL INFORMATION.
THIS DOCUMENT, INCLUDING THE DRAWING AND INFORMATION
CONTAINED THEREON, IS CONFIDENTIAL AND IS THE EXCLUSIVE
PROPERTY OF EATON CORPORATION, AND IS MERELY ON LOAN
AND SUBJECT TO RECALL BY EATON AT ANY TIME. BY TAKING
POSSESSION OF THIS DOCUMENT, THE RECIPIENT ACKNOWLEDGES AND AGREES THAT THIS DOCUMENT CANNOT BE USED IN ANY
MANNER ADVERSE TO THE INTERESTS OF EATON, AND THAT NO
PORTION OF THIS DOCUMENT MAY BE COPIED OR OTHERWISE REPRODUCED WITHOUT THE PRIOR WRITTEN CONSENT OF EATON.
IN THE CASE OF CONFLICTING CONTRACTUAL PROVISIONS, THIS
NOTICE SHALL GOVERN THE STATUS OF THIS DOCUMENT.
IQ 100 Series ((130/140/150) Meter
Table of Contents
Table of Contents
Disclaimer of Warranties and Limitation of Liability
Support Services
7
9
IQ 100 Series Meter Overview and Specifications
11
IQ 100 Series Mechanical Installation
19
IQ 100 Series Electrical Installation
23
Support Services
Website
EatonCare Customer Support Center
Technical Resource Center
European PanelMate Support Center
For Customers in Europe, contact:
Repair and Upgrade Service
Additional support is also available from our well-equipped
Repair and Upgrade Service (support for OI)
Hardware Overview
IQ 100 Series Meter / Digital Transducer 
IQ 100 Series Digital Transducer 
Voltage and Current Inputs
Universal Voltage Inputs 
Current Inputs 
Ordering Information
Measured Values
Programmable Values
Factory Settings
Utility Peak Demand (IQ140/150)
Specifications
Compliance
Accuracy
Introduction
ANSI Installation Steps
DIN Installation Steps IQ 100 Series Transducer Installation
Considerations When Installing Meters
CT Leads Terminated to Meter
CT Leads Pass-Through (No Meter Termination)
Quick Connect Crimp CT Terminations Voltage and Power Supply Connections
Ground Connections
Voltage Fuses
Electrical Connection Diagrams
User and Installation Manual IM02601003E - September 2011 www.eaton.com
9
9
9
10
10
10
10
10
10
11
11
11
11
11
12
12
13
13
14
14
15
17
18
19
20
21
22
23
24
25
26
27
27
27
28
3
IQ 100 Series (130/140/150) Meter
Table of Contents
IQ 100 Series Communication Installation
41
Programming the IQ 100 Series Meter Using the Front Panel
49
Programming the IQ 100 Series Meter Using Software
61
RS485 / KYZ Output (Communication Option)
IQ 100 Series Transducer Communication Information
Meter Connection
Configuring the Ethernet Connection
Introduction
Understanding Meter Face Elements
Understanding Meter Face Buttons
Using the Front Panel Understanding Startup and Default Displays
Using the Main Menu Using Reset Mode Entering a Password Using Configuration Mode
Configuring the Scroll Feature
Configuring CT Setting
Configuring PT Setting Configuring Connection Setting Configuring Communication Port Setting
Using Operating Mode
Understanding the % of Load Bar
% of Load Segment Table
Performing Watt-Hour Accuracy Testing (Verification)
Overview
Connecting to the IQ 100 Series Meter/Transducer
Accessing the IQ 100 Series Device Profile
Performing Device Profile Tasks
Configuring Settings Configuring Scaling  Functional Overview of CT and PT Ratios 
Configuring Energy and Display Settings 
Configuring Communication Settings  Configuring (System) Settings   Polling the IQ 100 Series Meter
Instantaneous Polling  Poll Power and Demand 
Poll Phasors  Using the IQ 100 Series Tools Menu
Accessing the Device Profile Screen 
Reset Device Information 
Retrieve Device Status  Flash Update Firmware 
4
User and Installation Manual IM02601003E-September 2011 www.eaton.com
41
44
44
44
49
49
49
50
50
51
51
52
53
54
55
56
57
57
59
59
59
60
61
61
62
63
64
64
64
65
66
66
67
67
68
69
70
70
70
70
70
IQ 100 Series ((130/140/150) Meter
Table of Contents
Performing Additional Tasks with Eaton Meter Configuration Software Using Connection Manager 
Disconnecting from an IQ 100 Series meter   Changing the Primary Device/Address  Merging Connection Databases 
Using the Options Screen 
Using the Help Menu  71
71
73
73
73
74
74
App. A: IQ 100 Series Navigation Maps
75
App.B Modbus Mapping for IQ 100 Series 81
Introduction Navigation Maps (Sheets 1 to 4) Main Menu Screens (Sheet 1) Operating Mode Screens (Sheet 2)
Reset Mode Screens (Sheet 3)
Configuration Mode Screens (Sheet 4)
Introduction
Modbus Register Map Sections
Floating Point Values 
Important Note Concerning the IQ 100 Series Modbus Map 
Modbus Register Map (MM-1 to MM-16)
User and Installation Manual IM02601003E - September 2011 www.eaton.com
75
75
76
77
78
79
81
81
82
83
5
IQ 100 Series (130/140/150) Meter
Table of Contents
6
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Disclaimer of Warranties and Limitation of Liability
Disclaimer of Warranties and Limitation of Liability
The information, recommendations, descriptions and safety notations in this document are based on
Eaton Corporation’s (“Eaton”) experience and judgment and may not cover all contingencies. If further
information is required, an Eaton sales office should be consulted. Sale of the product shown in this
literature is subject to the terms and conditions outlined in appropriate Eaton selling policies or other
contractual agreement between Eaton and the purchaser. THERE ARE NO UNDERSTANDINGS,
AGREEMENTS, WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A
PARTICULAR PURPOSE OR MERCHANTABILITY, OTHER THAN THOSE SPECIFICALLY SET OUT IN ANY
EXISTING CONTRACT BETWEEN THE PARTIES. ANY SUCH CONTRACT STATES THE ENTIRE OBLIGATION OF EATON. THE CONTENTS OF THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY
ANY CONTRACT BETWEEN THE PARTIES.
In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence),
strict liability or otherwise for any special, indirect, incidental or consequential damage or loss
whatsoever, including but not limited to damage or loss of use of equipment, plant or power system,
cost of capital, loss of power,additional expenses in the use of existing power facilities, or claims
against the purchaser or user by its customers resulting from the use of the information, recommendations and descriptions contained herein.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
7
IQ 100 Series (130/140/150) Meter
Disclaimer of Warranties and Limitation of Liability
8
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Support Services
Support Services
Support Services
The goal of Eaton is to ensure your greatest possible satisfaction
with the operation of our products. We are dedicated to
providing fast, friendly and accurate assistance. That is why we
offer you so many ways to get the support you need. Whether
it’s by phone, fax or e-mail, you can access Eaton’s support
information 24 hours a day, seven days a week. Our wide range
of services is listed below.
You should contact your local distributor for product pricing,
availability, ordering, expediting and repairs.
Website
Use the Eaton website to find product information. You can also
find information on local distributors or Eaton’s sales offices.
Website Address
www.eaton.com/electrical
EatonCare Customer Support Center
Call the EatonCare Support Center if you need assistance with
placing an order, stock availability or proof of shipment,
expediting an existing order, emergency shipments, product
price information, returns other than warranty returns, and
information on local distributors or sales offices.
Voice: 877-ETN CARE (386-2273) (8:00 am – 6:00 pm EST)
FAX: 800-752-8602
After-Hours Emergency: 800-543-7038
(6:00 pm – 8:00 am EST)
If you are in the US or Canada, and have OI or PLC questions,
you can take advantage of our toll-free line for technical
assistance with hardware and software product selection,
system design and installation, and system debugging and
diagnostics. Technical support engineers are available for calls
during regular buiness hours.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
9
IQ 100 Series (130/140/150) Meter
Support Services
Technical Resource Center
Voice: 877-ETN CARE (386-2273) (8:00 am – 5:00 pm EST)
FAX: (828) 651-0549
e-mail: TRC@Eaton.com
European PanelMate Support Center
This engineering company, located in Zurich, Switzerland,
provides high-level quality support and repair assistance for your
PanelMate products. You will receive technical and application
support.
For Customers in Europe, contact:
BFA Solutions, Ltd.
Voice: +41 1 806 64 44 (9:00 am – 5:00 pm CET)
e-mail: gk@bfa.ch
www.bfa.ch
Repair and Upgrade Service
Additional support is also available from our well-equipped
Repair and Upgrade Service department. If you have questions
regarding the repair or upgrade of OI product, contact your local
distributor.
Repair and Upgrade Service (support for OI)
Voice:
877-ETN-CARE (877-386-2273) (8:00 am – 5:00 pm EST)
414-449-7100 (8:00 am – 5:00 pm EST)
FAX: 614-882-3414
e-mail: TRC@eaton.com
10
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Overview & Specifications
IQ 100 Series Meter Overview and Specifications
Hardware Overview
The IQ 100 (IQ 130/140/150) is a multifunction power meter designed to be used in electrical substations, panel boards and as a power meter for OEM equipment. The unit provides multifunction measurement of most electrical parameters.
The unit is designed with advanced meaurement capabilities, allowing it to achieve high performance
accuracy. The IQ 100 meter is specified as a 0.5% class energy meter for billing applications as well as
a highly accurate panel indication meter.
The IQ 100 meter provides a host of additional capabilities, including optional RS485 with Modbus RTU
and RJ45 Ethernet connection with Modbus TCP communication.
IQ
•
•
•
•
•
•
•
100 meter features that are detailed in this manual are as follows:
0.5% Class Revenue Certifiable Energy and Demand (IQ 140/150) Metering
Meets ANSI C12.20 (0.5%)
Multifunction Measurement including Voltage, Current, Power, Frequency, Energy, etc.
Field Upgrade without Removing Installed Meter
Percentage of Load Bar for Analog Meter Perception
Easy to Use Faceplate Programming
RS485 or RJ45 Modbus Communication
The IQ 100 Series meter is available in two configurations: meter with integral display and transducer
only.
IQ 100 Series Meter with Integral Display
Meter with integral display in one compact unit. Features an optional RS485 (Modbus RTU) and KYZ
Pulse Output or optional RJ45 (Modbus TCP) Ethernet port and KYZ Pulse Output, and can be programmed using the faceplate of the meter. ANSI or DIN mounting may be used.
IQ 100 Series Digital Transducer (No display)
A Digital Transducer only unit providing KYZ Pulse Output and RS485 communication via Modbus RTU
or Modbus ASCII protocols or optional RJ45 (Modbus TCP) Ethernet port and KYZ Pulse Output. The
unit is designed to install using DIN Rail Mounting (see instructions on page 22).
Voltage and Current Inputs
Universal Voltage Inputs
Voltage Inputs allow measurement to 416 Volts Line-to-Neutral and 721 Volts Line-to-Line. This insures
proper meter safety when wiring directly to high voltage systems. One unit will perform to specification
on 69 Volt, 120 Volt, 230 Volt, 277 Volt, 277 Volt and 347 Volt power systems.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
11
IQ 100 Series (130/140/150) Meter
Overview &Specifications
Current Inputs
The IQ 100 Series meter’s Current Inputs use a unique dual input method:
• Method 1: CT Pass Through
The CT passes directly through the meter without any physical termination on the meter. This insures that the meter cannot be a point of failure on the CT circuit. This is preferable for utility users when sharing relay class CTs. No Burden is added to the secondary CT circuit.
• Method 2: Current Gills
This unit additionally provides ultra-rugged Termination Pass Through Bars that allow CT leads to
be terminated on the meter. This, too, eliminates any possible point of failure at the meter. This is a preferred technique for insuring that relay class CT integrity is not compromised (the CT will not open in a fault condition).
Ordering Information
IQ -
150 - M - A - 6 - 5 - 1 - 1
1
2
3
4
5
6
1. Model:
130 = Volts/Amps Meter
140 = Power Meter
150 = Energy Meter
2. Meter Type
M = Meter (with integral display)
T = Transducer Only (no display, with either RS485 or RJ45 option)
3. Frequency:
5 = 50 Hz System
6 = 60 Hz System
4. Current Input:
5 = 5 Amp Secondary
1 = 1 Amp Secondary
5. Power Supply:
1 = Universal, (90 - 265) VAC @50/60Hz or (100-370) VDC 4 = (18 - 60) VDC
6. Communication
0 = None (see Programmable Settings and Factory Settings sections beginning on the next page)
1 = RS485 with Modbus RTU and KYZ Pulse Output
2 = RJ45 Ethernet connection with Modbus TCP and KYZ Pulse Output
Example: IQ 150-M-A-6-5-1-1
(IQ 150 Energy Meter with 60 Hz System, 5 Amp Secondary, 90-265 VAC/100-370 VDC Power Supply, RS485
Modbus and KYZ Pulse Output)
12
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Overview & Specifications
Measured Values
The following table lists the measured values available for the different IQ 100 Series models.
Readings/Features
Volts L-N
Volts L-N Max/Min
Volts L-L
Volts L-L Max/Min
Amps
Amps Neutral
Amps Max/Min
kW, +/-/, Max/Min
kVAR, +/-/, Max/Min
PF, +/-/, Max/Min
kVA, Max,/Min
Frequency
kWh
kVARh
kVAh
Energy Accumulators
Demand Values
IQ 130
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
IQ 100 Series Feature Comparison
IQ 140
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
Yes
IQ150
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Programmable Values
An IQ 100 Series meter that does not have either the RS485 or RJ45 communication options can
only be programmed through the front panel. Not all meter settings are available through the front
panel. The following table lists the programmable settings for meters with and without RS485 or
RJ45 communication options.
COM
Option
Scroll
CT
Setting
PT
Connection Password Communication
Setting
Type
Enable
Reset
With RS485/
RJ45
Without
RS485/RJ45
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes*
Scaling
-Energy
and Power
Yes
No
* NOTES:
- Reset Energy is not available in a meter without RS485 or RJ45 communication option.
- Because a meter without RS485 or RJ45 communication option does not support password
enabling, the Reset Max/Min/All commands are not password protected.
The next section lists the factory settings for the IQ 100 Meter. Without either the RS485 or
RJ45 communication option, you won’t be able to change some of these settings.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
13
IQ 100 Series (130/140/150) Meter
Overview &Specifications
Factory Settings
The following table lists the default settings for the IQ 100 Series meter. The settings which
cannot be changed via the front panel are noted; if the meter does not have the RS485 or RJ45
option, these settings cannot be changed at all.
Setting
Default Value
Power Scale
Auto
Configurable through
Front Panel?
No
Energy Digits
Energy Decimal Places
Energy Scale
Power Direction
Demand Averaging Method
Demand Averaging Interval
Demand Averaging Sub-interval
Auto-Scrolling Display
8
0
kilo (k)
View as Load
Fixed
15 (minutes)
None
Yes
No
No
No
No
No
No
No
Yes
Display Configuration
Volts L-L, Volts L-N, Amps, W/VAR/PF, VA/Hz, Wh,
VARh, VAh
1 (for 1Amp model) or 5 (for 5 Amp model)
1 (for 1Amp model) or 5 (for 5 Amp model)
No
CT Numerator
CT Denominator
Yes
Not changeable through
software or front panel
No
Yes
Yes
Yes
Yes
No
Yes*
Yes*
Yes*
No*
No**
No**
No**
No**
No
CT Multiplier
1
PT Numerator
120
PT Denominator
120
PT Multipler
1
System Wiring
3 Element Wye
Phases Displayed
ABC
RS485 COM Address
1
RS485 COM Protocol
Modbus RTU
RS485 COM Baud Rate
57600
RS485 COM Response Delay
0
IP Address
10.0.0.1
Subnet Mask
255.255.255.0
Ethernet Option Baud Rate
57600
Ethernet Option Protocol
Modbus TCP
Password
Disabled
* If the meter does not have the RS485 option, these settings do not apply.
** If the meter does not have the RJ45 Ethernet option, these settings do not apply.
Utility Peak Demand (IQ140/150)
The IQ 100 Series meter provides user-configured Fixed Window or Sliding Window Demand. This
feature allows you to set up a Customized Demand Profile. Fixed Window Demand is demand used over
a user-configured demand period (usually 5, 15 or 30 minutes). Sliding Window Demand is a fixed
window demand that moves for a user-specified subinterval period. An example of Sliding Window
14
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Overview & Specifications
Demand is a 15-minute demand using 3 subintervals and providing a new demand reading every 5 minutes, based on the last 15 minutes.
Utility Demand Features can be used to calculate kW, kVAR, kVA and PF readings. All other parameters
offer Max and Min capability over the user-selectable averaging period. Voltage provides an Instantaneous Max and Min reading which displays the highest surge and lowest sag seen by the meter.
Specifications
Power Supply
·
Range:
1 Option: Universal, (90 to 265) VAC @50/60Hz or (100 to
370) VDC
4 Option: (18-60) VDC
·
Power Consumption:
5 VA, 3.5W
Voltage Inputs (Measurement Category III)
·
Range:
·
Supported hookups:
·
Input Impedance:
·
Burden: ·
Pickup Voltage:
·
Connection:
·
Max Input Wire Gauge:
·
Fault Withstand:
·
Reading:
Current Inputs
·
·
·
·
Class 10: Class 2:
Burden:
Pickup Current:
·
Connections: Universal, Auto-ranging up to 416VAC L-N, 721VAC L-L
3 Element Wye, 2.5 Element Wye, 2 Element Delta, 4 Wire
Delta
1M Ohm/Phase
0.0144VA/Phase at 120 Volts
10Vac
Screw terminal (Figure 3.4)
AWG#12 / 2.5mm2
Meets IEEE C37.90.1
Programmable Full Scale to any PT Ratio
5A Nominal, 10A Maximum
1A Nominal, 2A Maximum
0.005VA Per Phase Max at 11 Amps
0.1% of Nominal
O or U Lug Electrical Connection
Pass-through Wire, 0.177” / 4.5mm Maximum Diameter
Quick Connect, 0.25” Male Tab
Fault Withstand (at 23oC): 100A/10sec., 300A/3sec., 500A/1sec.
Reading:
Programmable Full Scale to any CT Ratio
·
·
Isolation
·
Environmental Rating
·
·
·
·
All Inputs and Outputs are galvanically isolated to 2500 VAC
Storage:
Operating:
Humidity:
Faceplate Rating:
(-20 to +70)0 C
(-20 to +70)0 C
to 95% RH Non-condensing
NEMA12 (Water Resistant), Mounting Gasket Included
User and Installation Manual IM02601003E - September 2011 www.eaton.com
15
IQ 100 Series (130/140/150) Meter
Overview &Specifications
Measurement Methods
·
Voltage, Current:
·
Power:
·
A/D Conversion:
Update Rate
·
·
Communication Format
Watts, VAR and VA:
All other parameters:
·
·
·
·
·
True RMS
Sampling at 400+ Samples per Cycle on All Channels
Measured Readings Simultaneously
6 Simultaneous 24 bit Analog to Digital Converters
100 milliseconds (Ten times per second)
1 second
1. Optional RS485 and KYZ Pulse Output through backplate
2. Optional RJ45 Ethernet connection and KYZ Pulse Output through backplate
Protocols: Com Port Baud Rate:
Com Port Address: Data Format:
IQ 100 Series Transducer
with RS485
Modbus RTU, Modbus ASCII, Modbus TCP
9600 to 57600 b/s
001-247
8 Bit, No Parity
Default Initial Communication Baud 9600 (see page 46)
Mechanical Parameters
·
Dimensions:
·
Weight:
(H4.85 x W4.85 x D4.65) inches, (H123.2 x W123.2 x
D118.1) mm
Mounts in 92mm square DIN or ANSI C39.1, 4” Round Cut-out
2 pounds, 0.907kg (ships in a 6”/152.4mm cube container)
KYZ/RS485 Port Specifications
RS485 Transceiver; meets or exceeds EIA/TIA-485 Standard
Type:
Min. Input Impedance:
Max. Output Current:
Two-wire, half duplex
96kΩ
±60mA
Wh Pulse
16
KYZ output contacts (and infrared LED light pulses through face plate):
(See page 56 for Kh values.)
Pulse Width:
Full Scale Frequency:
Contact type:
Relay type:
Peak switching voltage:
Continuous load current:
Peak load current:
40ms
~6Hz
Solid State – SPDT (NO – C – NC)
Solid state
DC ±350V
120mA
350mA for 10ms
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Overview & Specifications
On resistance, max.:
Leakage current:
Isolation:
Reset State:
Infrared LED:
Peak Spectral Wavelength:
Reset State:
Internal Schematic:
35Ω
1µA@350V
AC 3750V
(NC - C) Closed; (NO - C) Open
940nm
Off
Output timing:
T [s] =
NC
C
40
90ms
 Watthour 
3600 ⋅ Kh 

 pulse 
P[Watt ]
IR LED Light Pulses
Through face plate
ms
LED
OFF
LED
ON
LED
OFF
*
P[Watt] - Not a scaled value
Kh – See Section 6-4 for values
40
90ms
ms
LED
OFF
LED
ON
NO
KYZ output
Contact States
Through Backplate
NC
NC
NC
NC
NC
C
C
C
C
C
NO
NO
NO
NO
NO
(De-energized State)
* P [Watt] - not a scaled value
Kh - see page 56 for values.
Compliance
•
•
•
•
•
•
•
•
•
•
UL Listing: USL/CNL E185559
IEC 687 (0.5% Accuracy)
ANSI C12.20 (0.5% Accuracy)
ANSI (IEEE) C37.90.1 Surge Withstand
ANSI C62.41 (Burst)
CE Compliant
IEC1000-4-2: ESD
IEC1000-4-3: Radiated Immunity
IEC1000-4-4: Fast Transient
IEC1000-4-5: Surge Immunity
User and Installation Manual IM02601003E - September 2011 www.eaton.com
17
IQ 100 Series (130/140/150) Meter
Overview &Specifications
Accuracy
For 230 C, 3 Phase balanced Wye or Delta load, at 50 or 60 Hz (as per order), 5A (Class 10)
nominal unit.
Parameters
Accuracy
Accuracy Input Range
Voltage L-N [V]
Voltage L-L [V]
Current Phase [A]
Current Neutral (Calculated) [A]
Active Power Total [W]
Active Energy Total [Wh]
Reactive Power Total [VAR]
Reactive Energy Total [VARh]
Apparent Power Total [VA]
0.25% of reading
0.25% of reading
0.25% of reading1
2.0% of reading1
0.5% of reading1,2
0.5% of reading1,2
0.5% of reading1,2
0.5% of reading1,2
0.5% of reading1,2
(69 to 480)V
(120 to 600)V
(0.15 to 5)A
(0.15 to 5)A @ (45 to 65)Hz
(0.15 to 5)A@(69 to 480)V@+/(0.15 to 5)A@(69 to 480)V@+/(0.15 to 5)A@(69 to 480)V@+/(0.15 to 5)A@(69 to 480)V@+/(0.15 to 5)A@(69 to 480)V@+/-
Apparent Energy Total [VAh]
Power Factor
Frequency
% of Load Bar
0.5% of reading1,2
0.5% of reading1,2
+/- 0.01 Hz
+/- 1 segment
(0.15 to 5)A@(69 to 480)V@+/- (0.5 to 1)lag/lead PF
(0.15 to 5)A@(69 to 480)V@+/- (0.5 to 1)lag/lead PF
(45 to 65) Hz
(0.005 to 6)A
2
(0.5 to 1)lag/lead
(0.5 to 1)lag/lead
(0 to 0.8)lag/lead
(0 to 0.8)lag/lead
(0.5 to 1)lag/lead
PF
PF
PF
PF
PF
For 2.5 element programmed units, degrade accuracy by an additional 0.5% of reading.
- For 1A (Class 2) Nominal, degrade accuracy by an additional 0.5% of reading.
- For 1A (Class 2) Nominal, the input current range for Accuracy specification is 20% of the values listed in the table.
2
For unbalanced voltage inputs where at least one crosses the 150V auto-scale threshold (for
example, 120V/120V/208V system), degrade accuracy by additional 0.4%.
1
18
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Mechanical Installation
IQ 100 Series Mechanical Installation
Introduction
The IQ 100 Series meter can be installed using a standard ANSI C39.1 (4” Round) or an IEC 92mm DIN
(Square) form. In new installations, simply use existing DIN or ANSI punches. For existing panels, pull
out old analog meters and replace with the IQ 100 Series meter. The various models use the same
installation. See the next chapter for wiring diagrams.
Meter Face
ANSI Mounting
Rods - screw-in
Meter Dimensions
Transducer Dimensions
DIN
Mounting
Brackets
Meter Back
ANSI Mounting Panel Cut-out
DIN Mounting Cut-out
• Recommended Tools for IQ 100 Series meter Installation: #2 Phillips screwdriver, small wrench and
wire cutters. Transducer Installation doesn’t require any tools.
• Mount the meter in a dry location, which is free from dirt and corrosive substances. The meter is
designed to withstand harsh environmental conditions (see specifications in the previous chapter).
User and Installation Manual IM02601003E - September 2011 www.eaton.com
19
IQ 100 Series (130/140/150) Meter
Mechanical Installation
ANSI Installation Steps
NEMA 12 Mounting Gasket
Threaded Rods
Lock Washer and Nut
1.
2.
3.
4.
20
Insert 4 threaded rods by hand into the back of the meter. Twist until secure.
Slide ANSI 12 Mounting Gasket onto the back of the meter with rods in place.
Slide the meter with Mounting Gasket into the panel.
Secure from back of panel with lock washer and nut on each threaded rod.
Use a small wrench to tighten. Do not overtighten. The maximum installation torque
is 0.4 Newton-Meter.
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Mechanical Installation
DIN Installation Steps
DIN Mounting Bracket
Top Mounting Bracket Groove
Bottom Mounting Bracket Groove
#8 Screw
Meter with NEMA 12 Mounting Gasket
Remove (unscrew) ANSI studs for
DIN Installation
1. Slide the meter with NEMA 12 Mounting Gasket into the panel (first remove ANSI studs, if in
place).
2. From the back of the panel, slide 2 DIN Mounting Brackets into the grooves in the top and
bottom of the meter housing and snap them into place.
3. Secure the meter to the panel with a lock washer and a #8 screw through each of the 2
mounting brackets. Tighten with a #2 Phillips screwdriver. Do not overtighten.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
21
IQ 100 Series (130/140/150) Meter
Mechanical Installation
IQ 100 Series Transducer Installation
The IQ 100 Series Transducer model is installed using DIN Rail mounting.
Specs for DIN Rail mounting: DIN Rail (Slotted) dimensions:
International Standards DIN 46277-3
7.55mm x 35mm
Release Clip
Black Rubber Stoppers
DIN Rail Installation Steps:
1. Slide top groove of meter onto the DIN Rail.
2. Press gently until the meter clicks into place.
NOTE: If mounting with the DIN Rail provided,
use the Black Rubber Stoppers (also provided).
To Remove the Meter from the DIN Rail:
Pull down on the Release clip to detach the unit from
the DIN Rail.
NOTE ON DIN RAILS:
DIN Rails are commonly used as a mounting channel for most
terminal blocks, control devices, circuit protection devices and
PLCs. DIN Rails are made of electrolitically plated cold rolled
steel; they are also available in aluminum, PVC, stainless steel
and copper.
22
User and Installation Manual IM02601003E-September 2011 www.eaton.com
DIN Rail Detail
IQ 100 Series ((130/140/150) Meter
Electrical Installation
IQ 100 Series Electrical Installation
Considerations When Installing Meters
• Installation of the IQ 100 Series meter must be performed only by qualified personnel who follow
standard safety precautions during all procedures. Those personnel should have appropriate training
and experience with high voltage devices. Appropriate safety gloves, safety glasses and protective
clothing is recommended.
• During normal operation of the IQ 100 Series meter, dangerous voltages flow through many parts of
the meter, including: Terminals and any connected CTs (Current Transformers) and PTs (Potential
Transformers), all I/O Modules (Inputs and Outputs) and their circuits. All Primary and Secondary
circuits can, at times, produce lethal voltages and currents. Avoid contact with any current-carrying
surfaces.
• Do not use the meter for primary protection or in an energy-limiting capacity. The meter can only be
used as secondary protection.
• Do not use the meter for applications where failure of the meter may cause harm or death.
• Do not use the meter for any application where there may be a risk of fire.
• All meter terminals should be inaccessible after installation.
• Do not apply more than the maximum voltage the meter or any attached device can withstand. Refer
to meter and/or device labels and to the Specifications for all devices before applying voltages. Do
not HIPOT/Dielectric test any Outputs, Inputs or Communications terminals.
• Eaton recommends the use of Shorting Blocks and Fuses for voltage leads and power supply to prevent hazardous voltage conditions or damage to CTs, if the meter needs to be removed from
service. CT grounding is optional.
NOTE: IF THE EQUIPMENT IS USED IN A MANNER NOT SPECIFIED BY THE MANUFACTURER,
THE PROTECTION PROVIDED BY THE EQUIPMENT MAY BE IMPAIRED.
NOTE: THERE IS NO REQUIRED PREVENTIVE MAINTENANCE OR INSPECTION
NECESSARY FOR SAFETY. HOWEVER, ANY REPAIR OR MAINTENANCE SHOULD BE
PERFORMED BY THE FACTORY.
DISCONNECT DEVICE: The following part is considered the equipment disconnect device.
A SWITCH OR CIRCUIT-BREAKER SHALL BE INCLUDED IN THE END-USE EQUIPMENT OR
BUILDING INSTALLATION. THE SWITCH SHALL BE IN CLOSE PROXIMITY TO THE
EQUIPMENT AND WITHIN EASY REACH OF THE OPERATOR. THE SWITCH SHALL BE
MARKED AS THE DISCONNECTING DEVICE FOR THE EQUIPMENT.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
23
IQ 100 Series (130/140/150) Meter
Electrical Installations
CT Leads Terminated to Meter
The IQ 100 Series meter is designed to have Current inputs wired in one of three ways. The diagram
below shows the most typical connection where CT Leads are terminated to the meter at the current
gills. This connection uses nickel-plated brass studs (current gills) with screws at each end. This
connection allows the CT wires to be terminated using either an “O” or a “U” lug. Tighten the screws
with a #2 Phillips screwdriver. The maximum installation torque is 1 Newton-Meter.
Other current connections are shown in the figures on the next two pages. Voltage and RS485 connections are shown on page 27.
Current gill
(Nickel-plated brass stud)
CT Leads Terminated to Meter, #8 Screw for Lug Connection
Wiring Diagrams are shown beginning on page 28.
Communications Connections are detailed in the next chapter.
24
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Electrical Installation
CT Leads Pass Through (No Meter Termination)
The second method allows the CT wires to pass through the CT inputs without terminating at the meter.
In this case, remove the current gills and place the CT wire directly through the CT opening. The opening will accomodate up to 0.177” / 4.5mm maximum diameter CT wire.
CT wire passing through meter
Current gills removed
Pass Through Wire Electrical Connection
User and Installation Manual IM02601003E - September 2011 www.eaton.com
25
IQ 100 Series (130/140/150) Meter
Electrical Installations
Quick Connect Crimp CT Terminations
For quick termination or for portable applications, a quick connect Crimp CT connection can be used.
Crimp CT terminations
Quick Connect Electrical Connection
26
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Electrical Installation
Voltage and Power Supply Connections
Voltage Inputs are connected to the back of the unit via optional wire connectors. The connectors
accomodate up to AWG#12 / 2.5mm wire.
RS485 Output
DO NOT PUT THE VOLTAGE
ON THESE TERMINALS!
Power Supply Inputs
KYZ
Voltage Inputs
Voltage Connection
Ground Connections
The meter’s Ground Terminals should be connected directly to the installation’s protective earth ground.
Use 2.5mm wire for this connection.
Voltage Fuses
Eaton recommends the use of fuses on each of the sense voltages and on the control power, even
though the wiring diagrams in this chapter do not show them.
• Use a 0.1 Amp fuse on each voltage input.
• Use a 3 Amp fuse on the power supply.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
27
IQ 100 Series (130/140/150) Meter
Electrical Installations
Electrical Connection Diagrams
Choose the diagram that best suits your application. Be sure to maintain the CT polarity when wiring.
1. 3 Phase, 4 Wire System Wye with Direct Voltage, 3 Element
a. Example of Dual Phase Hookup
b. Example of Single Phase Hookup
2. 3 Phase, 4 Wire System Wye with Direct Voltage, 2.5 Element 3. 3 Phase, 4 Wire Wye with PTs, 3 Element
4. 3 Phase, 4 Wire Wye with PTs, 2.5 Element
5. 3 Phase, 3 Wire Delta with Direct Voltage
7. 3 Phase, 3 Wire Delta with 3 PTs
6. 3 Phase, 3 Wire Delta with 2 PTs
8. Current Only Measurement (Three Phase)
9. Current Only Measurement (Dual Phase)
10. Current Only Measurement (Single Phase)
1. Service: WYE, 4 Wire with No PTs, 3 CTs
N
A
B
C
HI
HI
HI
lc
lb
la
LO
LO
LO
GND
L (+)
N (-)
VRef
A
B
C
Power
Supply
C
A
N
A
B
C
Select: “3 EL WYE” (3 Element Wye) in Meter
Programming setup.
28
User and Installation Manual IM02601003E-September 2011 www.eaton.com
B
IQ 100 Series ((130/140/150) Meter
Electrical Installation
1a. Example of Dual Phase Hookup
User and Installation Manual IM02601003E - September 2011 www.eaton.com
29
IQ 100 Series (130/140/150) Meter
Electrical Installations
1b. Example of Single Phase Hookup
30
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Electrical Installation
2. Service: 2.5 Element WYE, 4-Wire with No PTs, 3 CTs
N
A
B
C
HI
HI
HI
lc
lb
la
LO
LO
LO
GND
L (+)
N (-)
VRef
A
B
C
Power
Supply
C
N
A
B
C
A
B
Select: “2.5 EL WYE” (2.5 Element Wye) in Meter
Programming setup.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
31
IQ 100 Series (130/140/150) Meter
Electrical Installations
3. Service: WYE, 4-Wire with 3 PTs, 3 CTs
N
A
B
C
HI
HI
HI
lc
lb
la
LO
LO
LO
GND
L (+)
N (-)
VRef
A
B
C
Power
Supply
C
N
A
B
C
A
Select: “3 EL WYE” (3 Element Wye) in Meter
Programming setup.
32
User and Installation Manual IM02601003E-September 2011 www.eaton.com
B
IQ 100 Series ((130/140/150) Meter
Electrical Installation
4. Service: 2.5 Element WYE, 4-Wire with 2 PTs, 3 CTs
N
A
B
C
HI
HI
HI
lc
lb
la
LO
LO
LO
GND
L (+)
N (-)
VRef
A
B
C
Power
Supply
C
N
A
B
C
A
B
Select: “2.5 EL WYE” (2.5 Element Wye) in Meter
Programming setup.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
33
IQ 100 Series (130/140/150) Meter
Electrical Installations
5. Service: Delta, 3-Wire with No PTs, 2 CTs
A
B
C
HI
HI
HI
lc
lb
la
LO
LO
LO
GND
L (+)
N (-)
VRef
A
B
C
Power
Supply
C
C
A
B
C
OR
B
Select: “2 Ct dEL” (2 CT Delta) in Meter
Programming setup.
34
User and Installation Manual IM02601003E-September 2011 www.eaton.com
A B
A
IQ 100 Series ((130/140/150) Meter
Electrical Installation
6. Service: Delta, 3-Wire with 2 PTs, 2 CTs
A
B
C
HI
HI
HI
lc
lb
la
LO
LO
LO
GND
L (+)
N (-)
VRef
A
B
C
Power
Supply
C
C
A
B
C
OR
B
A B
A
Select: “2 Ct dEL” (2 CT Delta) in Meter
Programming setup.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
35
IQ 100 Series (130/140/150) Meter
Electrical Installations
7. Service: Delta, 3-Wire with 2 PTs, 3 CTs
A
B
C
HI
HI
HI
lc
lb
la
LO
LO
LO
GND
L (+)
N (-)
VRef
A
B
C
Power
Supply
C
C
A
B
C
OR
B
Select: “2 Ct dEL” (2 CT Delta) in Meter
Programming setup.
36
User and Installation Manual IM02601003E-September 2011 www.eaton.com
A B
A
IQ 100 Series ((130/140/150) Meter
Electrical Installation
8. Service: Current Only Measurement (Three Phase)
Select: “3 EL WYE” (3 Element Wye) in Meter
Programming setup.
* Even if the meter is used for only Amp readings, the unit requires a Voltage reference.
Please make sure that the voltage input is attached to the meter.
AC Control Power can be used to provide the Reference Signal.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
37
IQ 100 Series (130/140/150) Meter
Electrical Installations
9. Service: Current Only Measurement (Dual Phase)
N
N
A
A
B
HI
HI
HI
lc
lb
la
LO
LO
LO
GND
L (+)
N (-)
VRef
A
B
C
Power
Supply
B
Select: “3 EL WYE” (3 Element Wye) in Meter
Programming setup.
* Even if the meter is used for only amp readings, the unit requires a Voltage reference.
Please make sure that the voltage input is attached to the meter.
AC Control Power can be used to provide the Reference Signal.
38
User and Installation Manual IM02601003E-September 2011 www.eaton.com
20VAC
Minimum
IQ 100 Series ((130/140/150) Meter
Electrical Installation
10. Service: Current Only Measurement (Single Phase)
N
N
A
HI
HI
HI
lc
lb
la
LO
LO
LO
GND
L (+)
N (-)
VRef
A
B
C
Power
Supply
20VAC
Minimum
A
Select: “3 EL WYE” (3 Element Wye) in Meter
Programming setup.
* Even if the meter is used for only amp readings, the unit requires a Voltage reference.
Please make sure that the voltage input is attached to the meter.
AC Control Power can be used to provide the Reference Signal.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
39
IQ 100 Series (130/140/150) Meter
Electrical Installations
40
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Communication Installation
IQ 100 Series Communication Installation
RS485 / KYZ Output (Communication Port Option)
The IQ 100 Series meter provides an optional combined RS485/KYZ Pulse Output communication port,
speaking Modbus ASCII or Modbus RTU.
• The IQ 100 Series meter’s RS485 connection uses standard 2-wire, Half Duplex architecture. The
RS485/KYZ Pulse Output connector is located on the terminal section of the meter. A connection
can easily be made to a Master Device or to other Slave devices.
• Care should be taken to connect + to + and - to - connections.
• See page 56 for the KYZ Output specifications and Pulse constants.
• RS485 allows you to connect one or multiple IQ 100 Series meters to a PC or other device, at either
a local or remote site. All RS485 connections are viable for up to 4000 feet (1219.20 meters).
User and Installation Manual IM02601003E - September 2011 www.eaton.com
41
IQ 100 Series (130/140/150) Meter
Communication Installations
The figure below shows a 2-wire RS485 connection in detail.
IQ 100 Series meter RS485 connections
MAX
MIN
From other RS485 device
Connect :
•
(−) to (−)
•
(+) to (+)
•
Shield(SH) to Shield(SH)
LM1
LM2
-
-
%THD
PRG
120%-
+
SH
+
SH
90%60%30%%LOAD
MENU
ENTER
120.0
120.0
120.0
VOLTS L-N
VOLTS L-N
AMPS
W/VAR/PF
A
VA/Hz
Wh
VARh
B
VAh
C
Wh Pulse
KILO
MEGA
For All RS485 Connections:
• Use a shielded twisted pair cable 22 AWG (0.33 mm2) or thicker, and ground the shield, preferably at
one location only.
• Establish point-to-point configurations for each device on a RS485 bus: connect (+) terminals to (+)
terminals; connect (-) terminals to (-) terminals.
• You may connect up to 31 meters on a single bus using RS485. Before assembling the bus, each
meter must have a unique address.
• Protect cables from sources of electrical noise.
• Avoid both “Star” and “Tee” connections (see figure on the next page).
• No more than two cables should be connected at any one point on an RS485 network, whether the
connections are for devices, converters, or terminal strips.
• Include all segments when calculating the total cable length of a network. If you are not using an
RS485 repeater, the maximum length for cable connecting all devices is 4000 feet (1219.20 meters).
• Connect shield to RS485 Master and individual devices as shown in the figure below. You may also
connect the shield to earth-ground at one point.
• Termination Resistors (RT) may be needed on both ends for longer length transmission lines. How
ever, since the meter has some level of termination internally, Termination Resistors may not be
needed. When they are used, the value of the Termination Resistors is determined by the electrical
parameters of the cable.
The figure below shows a representation of an RS485 Daisy Chain connection.
Master device
Last Slave device N
RT
SH
+
RT
-
Twisted pair, shielded (SH) cable
Slave device 1
Slave device 2
SH
SH
+
-
+
-
Twisted pair, shielded (SH) cable
Earth Connection, preferably at
single location
42
User and Installation Manual IM02601003E-September 2011 www.eaton.com
SH
Twisted pair, shielded (SH) cable
+
-
IQ 100 Series ((130/140/150) Meter
Communication Installation
Slave device 1
SH
+
-
Long stub results “T” connection that can cause
interference problem!
Master device
Last Slave device N
RT
RT
Slave device 2
SH +
-
SH
Twisted pair, shielded (SH) cable
+
-
SH
Twisted pair, shielded (SH) cable
+
-
Twisted pair, shielded (SH) cable
Earth Connection, preferably at
single location
Twisted pair, shielded (SH) cable
Twisted pair, shielded (SH) cable
Slave device 1
Slave device 2
SH +
-
Master device
SH
+
SH
+
-
+ SH
“STAR” connection can cause interference
problem!
-
SH
Slave device 3
+
Slave device 4
Twisted pair, shielded (SH) cable
Twisted pair, shielded (SH) cable
Incorrect Topologies
User and Installation Manual IM02601003E - September 2011 www.eaton.com
43
IQ 100 Series (130/140/150) Meter
Communication Installations
IQ 100 Series Transducer Communication Information
The IQ 100 Series Transducer model does not include a display or buttons on the front of the meter.
Programming and communication utilize either the RS485 connection or the optional RJ45 connection
on the back of the meter. Once a connection is established, Eaton Meter Configuration Software can be
used to program the meter and communicate to IQ 100 Series slave devices. Refer to the next chapter
for instructions on programming the meter.
Meter Connection
To provide power to the meter, attach an Aux cable to GND, L(+) and N(-). Refer to page 27.
Configuring the Ethernet Connection (RJ45 Port Option)
The RJ45 port option gives the IQ 100/100T Series meter a wired (RJ45) Ethernet connection speaking
Modbus TCP, allowing it to communicate on a Local Area Network (LAN). The meter is easily configured through a host PC using a Telnet connection. Once configured, you can access the meter directly
through any computer on your LAN.
This section outlines the procedures for setting up the parameters for Ethernet communication.
Setting up the Host PC to Communicate with the IQ100 Series meter
• Consult with your Network Administrator before performing these steps since some of the functions
may be restricted to Administrator privileges.
• The Host PC could have multiple Ethernet Adapters (Network Cards) installed. Identify and configure
the one that will be used for accessing the meter.
• The PC’s Ethernet Adapter must be set up for point-to-point communication when configuring the
RJ45 port option. The Factory default IP parameters programmed into the RJ45 port are:
IP Address: 10.0.0.1
Subnet Mask: 255.255.255.0
See following sections for additional parameters.
Configuring the Host PC’s Ethernet Adapter Using Windows XP©
The following example shows the PC configuration settings that let you access the IQ 100 Series meter
configured with default parameters. Use the same procedure when the settings differ from the default
settings.
1. From the Start Menu, select Control Panel>Network
Connections. You will see the window shown on the right.
2. Right click on the Local Area Network Connection you will
use to connect to the meter and select Properties from the
drop-down menu. You will see the window shown on the
next page.
44
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Communication Installation
3. Select Internet Protocol [TCP/IP] and click the Properties button. You will see the window shown
below.
4. Click the Use the Following IP Address radio button and enter these parameters:
IP Address:
10.0.0.2
Subnet Mask: 255.255.255.0
5. Click the OK button. You have completed the setup procedure.
Setting up the Ethernet Card in the IQ 100 Series meter
Below are the Factory Default settings for the IQ 100 Series meter’s Ethernet card. These are
programmed into the meter before it is shipped from the factory. Parameters in group 1 may need to be
altered to satisfy the local Ethernet configuration requirements. Other parameters (2, 3, 4) should not be
altered.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
45
IQ 100 Series (130/140/150) Meter
Communication Installations
• The Ethernet card in the IQ 100 Series meter can be locally or remotely configured using a Telnet
connection over the network.
• The configuration parameters can be changed at any time and are retained when the meter is not
powered up. After the configuration has been changed and saved, the Ethernet card performs a Reset.
• Only one person at a time should be logged into the network port used for setting up the meter. This
eliminates the possibility of several people trying to configure the Ethernet interface simultaneously.
• It is possible to reset the Ethernet card to its default values. See the procedure on the next page.
Configuring the IQ 100 Series Meter’s Ethernet Connection using Windows XP© on the Host Computer
Establish a Telnet connection on port 9999. Follow these steps:
1. From the Windows Start menu, click Run and type ‘cmd’.
2. Click the OK button to bring up the Windows’ Command Prompt window.
3. In the Command Prompt window, type: “telnet 10.0.0.1 9999” and press the Enter key.
NOTE: Make sure there is a space between the IP address and 9999.
When the Telnet connection is established you will see a message similar to the example shown
below.
4. To proceed to Setup Mode press Enter again. You will see a screen similar to the one shown below.
5. Change ONLY the parameters in group 1. To do so:
a. Type number “1.”
b. Once group 1 is selected, the individual parameters display for editing. Either:
• Enter a new parameter if a change is required.
• Press Enter to proceed to the next parameter without changing the current setting.
IMPORTANT! Settings 2, 3, and 4 MUST have the default values shown above.
46
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Communication Installation
(Example: Setting device with static IP Address.)
IP Address <010> 192.<000> 168.<000> .<000> .<001>
Set Gateway IP Address <N>? Y
Gateway IP Address: <192> .<168> .<000> .<001>
Set Netmask <N for default> <Y>? Y
6. Continue setting up parameters as needed. When you finish your modifications, make sure to press
the “S” key on the keyboard. This saves the new values and causes a Reset in the Ethernet card.
CAUTION! DO NOT PRESS ‘D’ as it will overwrite any changes and save the default values.
IMPORTANT! If the IP Address of the Ethernet card is lost, you can restore the factory default settings
by pressing the Reset button on the card. Follow the procedure below.
Resetting the Ethernet Card
The Ethernet card’s Reset button is accessed from the back of the IQ 100 Series meter. See the figure
below.
Reset Button
Using an implement such as a ballpoint pen tip, press and hold the Reset button for 30 seconds. The
Ethernet card is reset to the default settings shown on the previous page.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
47
IQ 100 Series (130/140/150) Meter
Communication Installations
48
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Programming the Meter Using the Front Panel
Programming the IQ 100 Series Meter Using the Front Panel
Introduction
You can use the Elements and Buttons on the IQ 100 Series meter’s face to view meter readings, reset
and/or configure the meter, and perform related functions. The following sections explain the Elements
and Buttons and detail their use.
Reading Type
Indicator
Understanding Meter Face Elements
The meter face features the following elements:
• Reading Type Indicator:
Indicates type of reading
• Parameter Designator:
Indicates reading displayed
• Watt-Hour Test Pulse:
Energy pulse output to test accuracy
• Scaling Factor:
Kilo or Mega multiplier of displayed readings
• % of Load Bar:
Graphic display of Amps as % of the load
Parameter
Designator
Watt-Hour
Test Pulse
Scaling
Factor
% of Load Bar
Meter Faceplate Elements
Understanding Meter Face Buttons
The meter face has Menu, Enter, Down and
Right buttons, which allow you to perform the
following functions:
• View meter information
• Enter display modes
• Configure parameters (may be Password protected)
• Perform resets (may be Password protected)
• Perform LED checks
• Change settings
• View parameter values
• Scroll parameter values
• View Limit states
Menu
Enter
Right
Down
Meter Faceplate Buttons
User and Installation Manual IM02601003E - September 2011 www.eaton.com
49
IQ 100 Series (130/140/150) Meter
Programming the Meter Using the Front Panel
Using the Front Panel
You can access the following modes using the meter’s front panel buttons:
• Operating mode (Default mode)
• Reset mode
• Configuration mode
Use the Menu, Enter, Down and Right buttons to navigate through each mode and its related
screens.
NOTES:
• Appendix A contains the complete Navigation map for the front panel display modes and their screens.
• The meter can also be configured using software (with optional communication); see the next chapter
for instructions.
Understanding Startup and Default Displays
Upon Power Up, the meter displays a sequence of screens:
• Lamp Test screen where all LEDs are lit
• Lamp Test screen where all digits are lit
• Firmware screen showing build number
• Error screen (if an error exists)
After startup, if auto-scrolling is enabled, the meter scrolls the parameter readings on the right side of the
front panel. The Kilo or Mega LED lights, showing the scale for the Wh, VARh and VAh readings. The
figure below shows an example of a Wh reading.
The meter continues to provide scrolling readings until one of the buttons on the front panel is pressed,
causing the meter to enter one of the other modes.
50
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Programming the Meter Using the Front Panel
Using the Main Menu
1. Press the Menu button. The Main Menu screen appears.
• The Reset mode (rSt) appears in the A window. Use the Down button to scroll, causing
the Configuration (CFG) and Operating (OPr) modes to move to the A window.
• The mode that is currently flashing in the A window is the “Active” mode, which means it is the
mode that can be configured.
For example: Press Down Once- CFG moves to A window. Press Down Once - OPr moves to A window.
2. Press the Enter button from the Main Menu to view the parameters screen for the mode that is
currently active.
Using Reset Mode
Reset mode resets all of the Max and Min values in the meter.
NOTE: With the communication options, you can reset both the Max/Min values
and the energy accumulators. If you do not have a communication option,
you cannot reset the energy accumulator fields.
Press the Enter button while rSt is in the A window. The Reset All? No screen
appears.
• If you press the Enter button again, the Main Menu appears,
with the next mode in the A window. (The Down button
does not affect this screen.)
• If you press the Right button, the Reset All? YES screen appears.
Press Enter to reset the meter’s Max and Min values.
CAUTION! Reset All? YES resets all Max and Min values. Only press Enter
if this is what you want to do.
NOTE: If Password protection is enabled for Reset, you must
enter the four digit Password before you can reset the meter.
(See page 66 for information on Password Protection.)
To enter a password, follow the instructions on the next page.
Once you have performed a reset, the screen displays “rSt All donE” and then resumes auto-scrolling
parameters.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
51
IQ 100 Series (130/140/150) Meter
Programming the Meter Using the Front Panel
Entering a Password
If Password protection has been enabled in the software for reset and/or configuration (see page 66 for
information), a screen appears requesting a password when you try to reset the meter and/or configure
settings through the front panel.
• PASS appears in the A window and 4 dashes appear in the B window. The leftmost dash is
flashing.
1. Press the Down button to scroll numbers from 0 to 9 for the flashing dash. When the correct number
appears for that dash, use the the Right button to move to the next dash.
Example: The left screen, below, shows four dashes. The right screen shows the display after the
first two digits of the password have been entered.
2. When all 4 digits of the password have been selected, press the Enter button.
• If you are in Reset mode and the correct password has been entered, “rSt All donE” appears
and the screen resumes auto-scrolling parameters.
• If you are in Configuration mode and the correct password has been entered, the display
returns to the screen that required a password.
• If an incorrect password has been entered, “PASS ---- FAIL” appears, and:
• The previous screen is redisplayed, if you are in Reset Mode.
• The previous Operating Mode screen is redisplayed, if you are in Configuration Mode.
52
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Programming the Meter Using the Front Panel
Using Configuration Mode
Configuration Mode follows Reset: Energy in the Main Menu.
To access Configuration mode:
1. Press the Menu button while the meter is auto-scrolling parameters.
2. Press the Down button until the Configuration Mode option (CFG) is in the A window.
3. Press the Enter button. The Configuration Parameters screen appears.
4. Press the Down button to scroll through the configuration parameters: Scroll (SCrL), CT, PT,
Connection (Cnct) and Port. The parameter currently ‘Active,” i.e., configurable, flashes in the A
window.
5. Press the Enter button to access the Setting screen for the currently active parameter.
NOTE: You can use the Enter button to scroll through all of the Configuration parameters and their
Setting screens, in order.
Press Enter when CFG is in A window -
Parameter screen appears - Press Down-
6. The parameter screen appears, showing the current settings. To change the settings:
• Use either the Down button or the Right button to select an option.
• To enter a number value, use the Down button to select the number value for a digit and the Right
button to move to the next digit.
NOTE: When you try to change the current setting and Password Protection is enabled for the
meter, the Password screen appears. See the previous page for instructions on entering a password.
7. Once you have entered the new setting, press the Menu button twice.
8. The Store ALL YES screen appears. You can either:
• Press the Enter button to save the new setting.
• Press the Right button to access the Store ALL no screen; then press the Enter button to cancel
the Save.
9. If you have saved the settings, the Store ALL done screen appears and the meter is reset.
Press the Enter button to save the settings Press the Enter button to
Press the Right button for Stor All no screen
Cancel the save
The settings have been saved
User and Installation Manual IM02601003E - September 2011 www.eaton.com
53
IQ 100 Series (130/140/150) Meter
Programming the Meter Using the Front Panel
Configuring the Scroll Feature
When in Auto Scroll mode, the meter performs a scrolling display, showing each parameter for 7
seconds, with a 1 second pause between parameters. The parameters the meter displays are
determined by the following conditions:
• They have been selected through software (refer to the next chapter for instructions).
• Their availability for the meter model (IQ130/140 or 150) may be restricted.
To enable or disable auto-scrolling:
1. Press the Enter button when SCrl is in the A window.
The Scroll YES screen appears.
2. Press either the Right or Down button if you want to access the
Scroll no screen.
To return to the Scoll YES screen, press either button.
3. Press the Enter button on either the Scroll YES screen (to enable auto-scrolling) or the Scroll no
screen (to disable auto-scrolling).
The CT- n screen appears (this is the next Configuration mode parameter).
NOTE:
• To exit the screen without changing scrolling options, press the Menu button.
• To return to the Main Menu screen, press the Menu button twice.
• To return to the scrolling (or non-scrolling) parameters display, press the Menu button three times.
54
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Programming the Meter Using the Front Panel
Configuring CT Setting
The CT Setting has three parts: Ct-n (numerator), Ct-d (denominator), and Ct-S (scaling).
1. Press the Enter button when Ct is in the A window.
The Ct-n screen appears. You can either:
• Change the value for the CT numerator.
• Access one of the other CT screens by pressing the Enter button: press Enter once to access the
Ct-d screen, twice to access the Ct-S screen.
NOTE: The Ct-d screen is preset to a 5 Amp or 1 Amp value at the factory and cannot be
changed.
a. To change the value for the CT numerator, from the Ct-n screen:
• Use the Down button to select the number value for a digit.
• Use the Right button to move to the next digit.
b. To change the value for CT scaling, from the Ct-S screen:
Use the Right button or the Down button to choose the scaling you want. The Ct-S setting can be
1, 10, or 100.
NOTE: If you are prompted to enter a password, refer to the instructions earlier in the chapter.
2. When the new setting is entered, press the Menu button twice.
3. The Store ALL YES screen appears. Press Enter to save the new CT setting.
Example CT Settings:
200/5 Amps: 800/5 Amps: 2,000/5 Amps: 10,000/5 Amps: Set
Set
Set
Set
the
the
the
the
Ct-n
Ct-n
Ct-n
Ct-n
value
value
value
value
for
for
for
for
200 and the Ct-S value for 1.
800 and the Ct-S value for 1.
2000 and the Ct-S value for 1.
1000 and the Ct-S value for 10.
NOTES:
• The value for Amps is a product of the Ct-n value and the Ct-S value.
• Ct-n and Ct-S are dictated by primary current; Ct-d is secondary current.
Press Enter
Use buttons to set Ct-n value The Ct-d can’t be changed Use buttons to select scaling
User and Installation Manual IM02601003E - September 2011 www.eaton.com
55
IQ 100 Series (130/140/150) Meter
Programming the Meter Using the Front Panel
Configuring PT Setting
The PT Setting has three parts: Pt-n (numerator), Pt-d (denominator), and Pt-S (scaling).
1. Press the Enter button when Pt is in the A window.
The PT-n screen appears. You can either:
• Change the value for the PT numerator.
• Access one of the other PT screens by pressing the Enter button: press Enter once to access the
Pt-d screen, twice to access the Pt-S screen.
a. To change the value for the PT numerator or denominator, from the Pt-n or Pt-d screen:
• Use the Down button to select the number value for a digit.
• Use the Right button to move to the next digit.
b. To change the value for the PT scaling, from the Pt-S screen:
Use the Right button or the Down button to choose the scaling you want. The Pt-S setting can be
1, 10, 100, or 1000.
NOTE: If you are prompted to enter a password, refer to the instructions earlier in this chapter.
2. When the new setting is entered, press the Menu button twice.
3. The STOR ALL YES screen appears. Press Enter to save the new PT setting.
Example Settings:
277/277 Volts: 14,400/120 Volts: 138,000/69 Volts: 345,000/115 Volts:
345,000/69 Volts: Pt-n
Pt-n
Pt-n
Pt-n
Pt-n
value
value
value
value
value
is
is
is
is
is
277, Pt-d value is 277, Pt-S value is 1.
1440, Pt-d value is 120, Pt-S value is 10.
1380, Pt-d value is 69, Pt-S value is 100.
3450, Pt-d value is 115, Pt-S value is 100.
345, Pt-d value is 69, Pt-S value is 1000.
NOTE: Pt-n and Pt-S are dictated by primary voltage; Pt-d is secondary voltage.
Use buttons to set Pt-n value
56
Use buttons to set Pt-d value Use buttons to select scaling
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Programming the Meter Using the Front Panel
Configuring Connection Setting
1. Press the Enter button when Cnct is in the A window. The Cnct screen appears.
2. Press the Right button or Down button to select a configuration.
The choices are:
• 3 Element Wye (3 EL WYE)
• 2.5 Element Wye (2.5EL WYE)
• 2 CT Delta (2 Ct dEL)
NOTE: If you are prompted to enter a password, refer to the
instructions earlier in this chapter.
3. When you have made your selection, press the Menu button twice.
4. The STOR ALL YES screen appears. Press Enter to save the setting.
Configuring Communication Port Setting
Port configuration consists of : Address (a three digit number), Baud Rate (9600; 19200; 38400; or
57600), and Protocol (Modbus RTU or Modbus ASCII).
1. Press the Enter button when POrt is in the A window.
The Adr (address) screen appears. You can either:
• Enter the address.
• Access one of the other Port screens by pressing the Enter button: press Enter once to access the
bAUd screen (Baud Rate); press Enter twice to access the Prot screen (Protocol).
a. To enter the Address, from the Adr screen:
• Use the Down button to select the number value for a digit.
• Use the Right button to move to the next digit.
b. To select the Baud Rate, from the bAUd screen:
Use the Right button or the Down button to select the setting you want.
c. To select the Protocol, from the Prot screen:
Press the Right button or the Down button to select the setting you want.
NOTE: If you are prompted to enter a password, refer to the instructions earlier in this chapter.
2. When you finish making your selections, press the Menu button twice.
3. The STOR ALL YES screen appears. Press Enter to save the settings.
Use buttons to enter Address
Use buttons to select Baud Rate
Use buttons to select Protocol
User and Installation Manual IM02601003E - September 2011 www.eaton.com
57
IQ 100 Series (130/140/150) Meter
Programming the Meter Using the Front Panel
Using Operating Mode
Operating Mode is the IQ 100 Series meter’s default mode, that is, the standard front panel display.
After Startup, the meter automatically scrolls through the parameter screens, if scrolling is enabled.
Each parameter is shown for 7 seconds, with a 1 second pause between parameters. Scrolling is suspended for 3 minutes after any button is pressed.
1. Press the Down button to scroll all the parameters in Operating Mode. The currently “Active,” i.e.,
displayed, parameter has the Indicator light next to it, on the right face of the meter.
2. Press the Right button to view additional readings for that parameter. The table below shows possible
readings for Operating Mode. Sheet 2 in Appendix A shows the Operating Mode Navigation map.
NOTE: Readings or groups of readings are skipped if not applicable to the meter type or hookup, or if
they are disabled in the programmable settings.
Operating Mode Parameter Readings
POSSIBLE READINGS
VOLTS L-N
VOLTS L-L
AMPS
W/VAR/PF
VA/Hz
Wh
VARh
VAh
58
VOLTS_LN
VOLTS_LN_
MAX
VOLTS_LL
VOLTS_LL_
MAX
AMPS
AMPS_NEUTRAL
W_VAR_PF W_VAR_PF_
MAX_POS
VA_FREQ
VA_FREQ_
MAX
KWH_REC
KWH_DEL
KVARH_POS KVARH_
NEG
KVAH
VOLTS_LN_
MIN
VOLTS_LL_
MIN
AMPS_MAX AMPS_MIN
W_VAR_PF_
MIN_POS
VA_FREQ_
MIN
KWH_NET
KVARH_NET
User and Installation Manual IM02601003E-September 2011 www.eaton.com
W_VAR_PF_
MIN_NEG
KWH_TOT
KVARH_
TOT
IQ 100 Series ((130/140/150) Meter
Programming the Meter Using the Front Panel
Understanding the % of Load Bar
The 10-segment LED bar graph at the bottom left of the IQ 100 Series front panel provides a graphic
representation of Amps. The segments light according to the load, as shown in the table below.
When the Load is over 120% of full load, all segments flash “On” (1.5 secs) and “Off” (0.5 secs).
% of Load Segment Table
Segments
Load >= % Full Load
none
1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
All Blink
no load
1%
15%
30%
45%
60%
72%
84%
96%
108%
120%
>120%
% of Load Bar
User and Installation Manual IM02601003E - September 2011 www.eaton.com
59
IQ 100 Series (130/140/150) Meter
Programming the Meter Using the Front Panel
Performing Watt-Hour Accuracy Testing (Verification)
To be certified for revenue metering, power providers
and utility companies must verify that the billing energy
meter performs to the stated accuracy. To confirm the
meter’s performance and calibration, power providers use
field test standards to ensure that the unit’s energy
measurements are correct. Since the IQ 100 Series meter is a
traceable revenue meter, it contains a utility grade test pulse
that can be used to gate an accuracy standard. This is an
essential feature required of all billing grade meters.
Watt-Hour
Test Pulse
• Refer to the figure below for an example of how this process works.
• Refer to the table below for the Wh/Pulse constants for accuracy testing.
Using the Watt-Hour Test Pulse
Infrared & KYZ Pulse Constants for Accuracy Testing - Kh Watt-hour per pulse
Input Voltage Level
Below 150V
Above 150V
Class 10 Models
0.2505759630
1.0023038521
Class 2 Models
0.0501151926
0.2004607704
NOTES:
• Minimum pulse width is 40 milliseconds.
• Refer to the Pulse specifications in the Overview and Specifications chapter.
60
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Programming the IQ 100 Series Meter Using Software
Programming the IQ 100 Series Meter Using Software
Overview
The IQ 100 Series meter can be configured using either the meter’s faceplate buttons (Menu, Enter,
Down and Right) or Eaton Meter Configuration software. To connect to the meter for software configuration, use the RS485 port, if equipped, on the back panel of the meter, or the RJ45 port if the meter
has the Ethernet card option.
The IQ 100 Series Transducer must be configured with the Eaton Meter Configuration software, using
either the RS485 port or the optional RJ45 port, since it does not have a front panel.
This chapter contains instructions for programming the meter and Transducer using software.
Connecting to the IQ 100 Series Meter/Transducer
1. Open Eaton Meter Configuration software.
2. Click the Connect icon on the Title bar or
Connection>Quick Connect.
3. If you are connecting to the meter through your PC:
a. Make sure the Serial Port radio button is selected.
b. Enter Device Address (1-247).
c. Select Baud Rate from the pull-down menu.
d. Select the port you are using from the pull-down menu. The
Available Ports/All Ports radio buttons determine which port
selections the menu displays.
e. Select Modbus RTU from the Protocol pull-down menu.
f. Select Flow Control: None or Hardware.
g. Select Echo Mode: No Echo or Static Echo.
If you are connecting to the meter through the Power Xpert® Gateway
or through the RJ45 port option:
a. Make sure the Network radio button is selected.
b. Enter Device Address (1-247).
c. Enter the Gateway or the meter’s Ethernet card IP Address.
d. Enter Network Port (502 for Modbus).
e. Protocol defaults to Modbus TCP.
4. Click the Connect button. You will see the Device Status
screen, shown below on the right.
NOTE for IQ 100 Series Transducer:
When the Transducer is powered up, for 10
seconds you can connect to the meter using the
Factory Initial Default Settings (even if the Device
Profile has been changed). After 10 seconds,
the Device Profile reverts to the actual Device
Profile in use.
Factory Initial Default Settings
9600
Baud Rate:
Port:
COM1
Modbus RTU
Protocol:
User and Installation Manual IM02601003E - September 2011 www.eaton.com
61
IQ 100 Series (130/140/150) Meter
Programming the IQ 100 Series Using Software
Accessing the IQ 100 Series Device Profile
1. Click the Profile icon in the Title Bar.
2. You will see the IQ 100 Device Profile screen. The tabs
at the top of the screen allow you to navigate between
Settings screens. The Buttons at the bottom of the screen allow you to perform tasks, for
example, updating the Device Profile. See the example screen below.
.
Tabs
Settings Screen
Buttons
3. To select a setting, click on its tab at the top of the screen. This causes the Settings screen to be
displayed. See the following sections for instructions on configuring meter settings.
62
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Programming the IQ 100 Series Meter Using Software
Performing Device Profile Tasks
You can perform the following tasks using the Device Profile screen buttons.
• Update: Click to send the current settings to the meter.
NOTE: You must click the Update Device button after making changes in the Settings screens, if you
want to update the connected meter’s settings.
• Cancel: Click to leave the Device Profile Editor screen without
saving any changes.
• Load: Click to load a previously saved Device Profile
settings file. You will see the Load Programmable Settings
window, shown on the right.
Select the saved Device Profile you want and click Open.
The settings from that file now appear in the Settings
screens; for example, the CT and PT Ratios will be those
from the saved Device Profile, rather than from the
currently connected meter.
• Save: Click to save the Device Profile settings to a file. You
will see the Save Programmable Settings window, shown on
the right. Give a name to the Device Profile file and click
Save.
• Report: Click to open a Notepad window containing the
Device Profile settings in a text file. See the example
window, shown on the right.
• Print the text file by selecting File>Print from the
Notepad Title Bar.
• Save the text file by selecting File>Save from the
Notepad Title Bar.
NOTE: When you click Report, you will be given the choice
of viewing the Device Profile report or printing the report
without viewing it on the screen.
·
User and Installation Manual IM02601003E - September 2011 www.eaton.com
63
IQ 100 Series (130/140/150) Meter
Programming the IQ 100 Series Using Software
Configuring Settings
The following sections contain detailed instructions for configuring the Device Profile settings. All of the
settings are reached from tabs at the top of the Device Profile screen.
Configuring Scaling
Use this setting to configure Current Transformer and Potential Transformer ratios and to select the
wiring (System Hookup).
Functional Overview of CT and PT Ratios
Current and Potential transformers are used mainly for the following reasons:
• To insulate, and as a result isolate, the meter from high-voltage circuits
• To change the primary voltage and current to standard values and sizes that the meter can measure.
The CT and PT transformers deliver fractions of the primary voltage and current to the meter. With
properly set ratios and multipliers, the readings of the meter can be used to determine the energy,
voltage, current, or power of the system.
This setting is the first screen displayed when you open the IQ 100 Series Device Profile. If you have
been on another screen, click the Scaling tab to re-display this screen. The screen fields and acceptable
entries are as follows:
CT Ratios
CT Numerator (Primary): 1 - 9999
CT Denominator (Secondary): 5 or 1 Amp
NOTE: This field is display only.
CT Multiplier (Scaling): 1, 10 or 100
Current Full Scale: Display only.
PT Ratios
PT Numerator (Primary): 1 - 9999
PT Denominator (Secondary): 40 - 600
PT Multiplier (Scaling): 1, 10, 100, or 1000
Voltage Full Scale: Display only.
System Wiring
3 Element Wye; 2.5 Element Wye; 2 CT Delta
Example Settings:
For a CT of 2000/5A, set the following CT Ratios in the entry fields:
2000
CT Numerator (Primary)
5
CT Denominator (Secondary) CT Multiplier
1
The Current Full Scale field will read 2000.
NOTE: You can obtain the same Current Full Scale by entering a CT Numerator of 200 and a CT
Multiplier of 10.
64
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Programming the IQ 100 Series Meter Using Software
For a system that has 14400V primary with a 120V secondary line to neutral (PT Ratio of 120:1), set
the following PT Ratios in the entry fields:
1440
PT Numerator (Primary) PT Denominator (Secondary)
120
PT Multiplier
10
The Voltage Full Scale field will read 14400.
Configuring Energy and Display Settings
Click the Energy and Display tab. You will see the screen shown on
the right. It displays the current settings for Power and Energy format,
Demand averaging (IQ140 and above), auto-scrolling and display
configuration. The screen fields and acceptable entries are as
follows:
Power and Energy Format
Power Scale: Unit, kilo (k), Mega (M), Auto
Energy Digits: 5, 6, 7, 8
Decimal Places: 0 - 6
Energy Scale: Unit, kilo (k), Mega (M)
Example: Shows an example of selected settings.
Power Direction: View as Load or View as Generator
NOTES:
• The Energy Digits, Scale and Decimal Places settings determine how the Energy values are displayed.
• If invalid values are entered, you will see the following warning message:
“Warning: Current CT, PT and Energy Settings may cause invalid energy accumulator values.”
Once you correct the values and click Recalculate this message goes away.
Demand Averaging (IQ140/150 only)
Average Method: Fixed or Sliding
Interval: 5, 15, 30 or 60 Minutes
Subinterval: 1, 2, 3 or 4
NOTE: Fixed Average cannot have a subinterval.
Auto Scroll Display
Clicking the checkbox turns auto-scrolling On and Off. Auto-scrolling controls the display of selected
parameters on the meter’s faceplate.
Display Configuration
Check the boxes of the Readings you want displayed on the faceplate of the meter. You must select at
least one reading.
NOTE: This setting can be ignored for the IQ100 Series transducer, since it doesn’t have a display.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
65
IQ 100 Series ((130/140/150) Meter
Programming the IQ 100 Series Meter Using Software
Configuring Communication Settings
Use this setting to configure communication settings for the meter’s RS485 Port.
NOTES:
• The settings on this screen are the current settings for communication.
• Any changes may affect communication between the meter and your PC.
Click the Communication tab. You will see the screen shown on the
right. The screen fields and acceptable entries are as follows:
COM 2 (RS485)
1 - 247
Address:
Protocol:
Modbus RTU, Modbus ASCII or DNP 3.0
Baud Rate: 9600, 19200, 38400, 57600
Response Delay: 0 - 750 (50 msec increments)
NOTE: Response Delay is the delay the meter should use before
responding to queries. If your connecting device requires a delay
before receiving information, use response delay to program the time
to wait before the meter starts responding to queries.
Configuring (System) Settings
Use this setting to configure meter password or assign a meter designation.
Click the Settings tab. You will see the screen shown on the right.
• To enable or disable Password protection for reset and/or
configuration:
Click the checkbox next to the option. Enabling Password
protection prevents unauthorized tampering with devices.
IMPORTANT! You must set up a password before enabling
Password protection. Click the Change button next to Change
Password if you have not already set up a password.
• To Change the device designation: input a new designation into
this field.
When you click the Change button next to Change Password
in the Settings screen, you will see the message window shown on
the right.
1. Type in the new password (0 - 9999).
2. Retype the password.
3. Click Change. The new password is saved and the meter restarts.
4. You can now enable the password for reset (Reset Max/Min Energy Settings) or configuration
(Device Profile) by clicking the checkbox next to the option.
When a user attempts to make a change that is under Password protection, the Eaton Meter Configuration software opens a message window asking for the password. If the correct password is not entered,
the change does not take place.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
66
IQ 100 Series ((130/140/150) Meter
Programming the IQ 100 Series Meter Using Software
Polling the IQ 100 Series Meter
The Real Time Poll features of Eaton Meter Configuration software are used to continuously view
instantaneous values within an IQ 100 Series meter. The software provides tabular views of metered
values, circuit measurements, interval data, and pulse data.
The Real Time Poll features are divided into three groups, accessed by clicking Real-Time Poll in the Title
Bar:
• Real Time Readings
• Revenue, Energy and Demand Readings
• Power Quality
When you click Real Time Readings; Revenue, Energy and Demand Readings; and Power Quality and
Alarms, you will see a sub-menu that allows you to select individual polling screens.
NOTE: Clicking the Polling icon on the Title Bar is the same as selecting Instantaneous Polling from the
Real-Time Poll>Real Time Readings menu; clicking the Phasors icon on the Title Bar is the same as
selecting Phasors from the Real-Time Poll>Power Quality and Alarms menu.
Instantaneous Polling
Click Real-Time Poll>Real Time Readings>Instantaneous Polling. You will see the screen shown below.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
67
IQ 100 Series (130/140/150) Meter
Programming the IQ 100 Series Using Software
• Click Print to print a copy of the screen.
• Click Help to view instructions for this screen.
• Click OK to return to the main screen.
Poll Power and Demand
Click Real-Time Poll>Revenue, Energy and Demand Readings>Power and Demand. You will see the
screen shown below.
• Click Print to print a copy of the screen.
• Click Help to view instructions for this screen.
• Click OK to return to the main screen.
68
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Programming the IQ 100 Series Meter Using Software
Poll Phasors
Click Real Time Poll>Power Quality and Alarms>Phasors. You will see the screen shown below.
The Phasors screen displays the Phase relationships of the currently connected meter. If you have an
auxiliary voltage reading (i.e. generator and bus where the VAux is the generator), the Aux box and the
VAux phasor are displayed. The VAux phasor is referenced to VA phase.
To adjust the Phasor display, click Options at the bottom of the screen.
You will see the screen shown on the right.
a. In the Display Angles Increasing and Phasor Rotation boxes,
select either Clockwise or Counter Clockwise.
b. From the pull-down menu at the bottom of the screen, select
Vectors, Triangles or Vectors and Triangles to change the
graphic representation of the data.
Click OK to save your selections and return to the Phasors screen.
•
•
•
•
Click
Click
Click
Click
Copy to save a copy of the screen to the clipboard.
Print to send a copy of the graph to a printer.
Help to view instructions for this screen.
OK to return to the main screen.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
69
IQ 100 Series ((130/140/150) Meter
Programming the IQ 100 Series Meter Using Software
Using the IQ 100 Series Tools Menu
The Tools Menu allows you to access specific functions
for the IQ 100 Series Meter. Click Tools from the Title Bar
to display the Tools Menu.
Accessing the Device Profile Screen
Click the first option, Edit Current Device Profile, to open
the Device Profile screen. This menu option performs the
same function as clicking the Profile icon in the Title Bar.
Reset Device Information
Click this option to reset either Max/Min values (IQ 130, IQ 140,
and IQ 150 meters) and/or Energy Accumulators (IQ 150 only).
You will see the screen shown on the right. Click the checkbox
next to the item(s) you want to reset.
Retrieve Device Status
Click this option to see the Device status screen for the meter. this is the same screen that displays
when you first connect to the meter.
Flash Update Firmware
Click this option to upgrade the meter’s firmware. You will
see the screen on the right.
Click Browse to locate the flash file.
Click OK to update the firmware with the flash file. When
flashing is complete, click Exit to close the screen.
NOTE: Flash updating of firmware can only be done at a Baud
Rate of 57.6k.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
70
IQ 100 Series (130/140/150) Meter
Programming the IQ 100 Series Using Software
Performing Additional Tasks with Eaton Meter Configuration Software
The following sections contain instructions for other tasks you can perform using the Eaton Meter
Configuration software.
Using Connection Manager
Use Connection Manager to add or remove connection
locations and/or devices at locations.
1. Click Connection>Connection Manager or click on the
Connect Mgr icon. You will see the screen shown on
the right.
List of Locations:
On the left side of the Connection Manager screen is a List
of Locations. These are the locations of one or more
meters to which you can connect. You can add a location
and/or a device; edit a location and/or device; or remove
a location and/or device.
• To add a location:
a. Click on the Add button. You will see the Connection
Manager Location Editor screen. On this screen,
you program the Communication settings for each
new location.
b. Type a name for the new location.
c. Click Serial Port or Network.
d. Enter Communication settings:
Com Port: Baud Rate: Flow Control: Data Bits: Parity: COM 1 - 99
1200 - 115200
None or Hardware
8 (or 7)
None (Even, Odd)
e. To add a device:
- Click Add Serial (to add a Serial Port connected
device) or Add Net (to add a Network connected device) in the Devices at Location box. You
can add up to 255 devices (Serial Port and/or Network connected) at one location.
NOTES:
• All devices must have the same connection parameters: Baud, Parity and Flow Control.
• Multiple devices slow down polling.
71
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Programming the IQ 100 Series Meter Using Software
f. To edit a device:
- Select the device from the Devices at Location box. (Scroll
down to find all devices.)
- Click Edit. You will see the Connection Manager Location
Device Editor screen, shown on the right.
- Use this screen to program the device properties for each
device at a location.
• If the device has a Serial Port device connection, you will
see the first (top) example screen.
• If the device has a Network device connection, you will
see the second example screen.
NOTE: Click the Network or Serial button at the top of the
screen to switch connection screens.
- Enter Device Properties:
Address: 1 - 247 (Unique Address)
Name: Device Name
Description: (Type and Number, for example)
Protocol: Modbus RTU, ASCII, or Modbus TCP
Device Type: IQ Meter
Comm Port: 1 or 2 (Serial Port Only)
IP Address:
100.10.10.10 (for example) (Network
Only)
Port Number:
502 (Default) (Network Only)
- Click Close to save settings and return to the Connection
Manager Location Editor screen.
g. To remove a device, select the device from the Devices at Location box and click Remove.
h. Click Close to return to the Connection Manager screen.
• To edit a location:
a. Select a location from the List of Locations box.
b. Click the Edit button. The Connection Manager Location Editor screen appears, displaying the current
settings for the location.
c. Make any changes to settings and/or devices at the location.
d. Click Close to exit the screen.
• To
a.
b.
c.
remove a location:
Select a location from the List of Locations box.
Click Remove.
Click Yes in the Confirmation window.
• To sort the list of locations:
a. Select a sort method (A-Z, Z-A, Newest-Oldest or Oldest-Newest) from the pull-down menu.
b. Click Sort By.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
72
IQ 100 Series (130/140/150) Meter
Programming the IQ 100 Series Using Software
• To connect to a location:
a. Select the location you want to connect to from the List of Locations box.
NOTE: You may only connect to one location at a time. To change to a different location, you must
disconnect from the current location by selecting it and clicking Disconnect.
b. Click Connect. When the connection is made, the selected location appears in the Connected To
Locations section of the screen.
c. Click Close. The Device Status screen opens, confirming the connection. The computer Status bar
at the bottom of the screen also confirms the computer’s connection parameters.
NOTE: If the connection fails, a popup screen alerts you. Check that all cables are secure, that the
RS232 cable is connected to the correct Com Port on the computer, and that the computer is set to use
the same baud rate and protocol as the meter to which the computer is connected.
Disconnecting from an IQ 100 Series meter
To disconnect from an IQ 100 Series meter or from a location, do one of the following:
• Click on the Disconnect icon in the Title Bar.
• Select Connection>Disconnect from the Title Bar.
• From the Connection Manager screen, select the location from the Connected to Location field and
click the Disconnect button.
Changing the Primary Device/Address
Use this feature to select another meter as the primary device.
1. Click Connect>Change Primary Device/Address. You will
see the screen on the right.
2. Enter the address of the device you want to designate as the
new Primary Device.
3. Click OK.
Merging Connection Databases
Use this feature to combine two sets of cnexcom databases.
1. Click Connection>Merge Connection Databases. You will
see the screen on the right. It allows you to select the two
databases to merge.
2. Click the Browse button next to each field to pick the
databases. The Source cnexcom database will be merged
into the Destination cnexcom database.
3. Click the Merge button to proceed with the merge; click OK
to exit the screen.
73
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
Programming the IQ 100 Series Meter Using Software
Using the Options Screen
1. Click View>Options. You will see the screen shown on
the right. Use this screen to access the following
features:
• Paths for Eaton Meter Configuration software files
• Data Scan mode
Use the tabs at the top of the screen to access these
features.
2. The first Options screen is the Paths screen, shown on
the right. Use this screen to view or change the paths
the Eaton Meter Configuration software uses for data.
3. Click the Data Scan Mode tab to see the second screen
on the right. Use this screen to select normal scan rate
or to enter a custom scan rate.
4. Click:
• Apply to apply your selection(s) and keep the
Options screen open
• Okay to apply your selection and close the
Options screen
• Cancel to close the Options screen without
saving any selections that have not been applied
Using the Help Menu
The Help menu, accessed by clicking Help in the Title Bar, allows you to:
• View this manual online: click Help>this User Manual.
• View information about the Eaton Meter Configuration software, including version number: click
Help>About Eaton Meter Configuration Software.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
74
IQ 100 Series ((130/140/150) Meter
App A: Navigation Maps
App. A: IQ 100 Series Navigation Maps
Introduction
You can configure the IQ 100 Series meter and perform related tasks using the buttons on the meter
face. This appendix contains the Navigation maps for the meter’s front panel displays.
Navigation Maps (Sheets 1 to 4)
The IQ 100 Series Navigation maps begin on the next page. The maps show in detail how to move
from one screen to another and from one display mode to another using the buttons on the face of the
meter. All display modes automatically return to Operating mode after 10 minutes with no user
activity.
Navigation map titles:
•
•
•
•
Main Menu screens (Sheet 1)
Operating mode screens (Sheet 2)
Reset mode screens (Sheet 3)
Configuration mode screens (Sheet 4)
User and Installation Manual IM02601003E - September 2011 www.eaton.com
75
IQ 100 Series (130/140/150) Meter
App A: Navigation Maps
76
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
App A: Navigation Maps
User and Installation Manual IM02601003E - September 2011 www.eaton.com
77
IQ 100 Series (130/140/150) Meter
App A: Navigation Maps
78
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
App A: Navigation Maps
User and Installation Manual IM02601003E - September 2011 www.eaton.com
79
IQ 100 Series (130/140/150) Meter
App A: Navigation Maps
80
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
App B: Modbus Map
App.B: Modbus Mapping for the IQ 100 Series
Introduction
The Modbus map for the IQ 100 Series meter gives details and information about the possible readings
of the meter and its programming.
Modbus Register Map Sections
The IQ 100 Series Modbus register map includes the following sections:
Fixed Data Section, Registers 1- 47, details the meter’s Fixed Information.
Meter Data Section, Registers 1000 - 12031, details the meter’s readings, including Primary readings,
Energy Block, Demand Block (IQ 140/150 meter), Phase Angle Block, Status Block, and Minimum and
Maximum readings.
Commands Section, Registers 20000 - 26011, details the meter’s Resets Block, Programming Block,
Other Commands Block and Encryption Block.
Programmable Settings Section, Registers 30000 - 33575, details all the setups you can program to
configure your meter.
Secondary Readings Section, Registers 40001 - 40100, details the meter’s Secondary readings.
Data Formats
ASCII:
ASCII characters packed 2 per register in high, low order and without any
termination characters.
SINT16/UINT16:
16-bit signed/unsigned integer.
SINT32/UINT32:
32-bit signed/unsigned integer spanning 2 registers. The lower-addressed
register is the high order half.
FLOAT:
32-bit IEEE floating point number spanning 2 registers. The lower-addressed
register is the high order half (i.e., contains the exponent).
User and Installation Manual IM02601003E - September 2011 www.eaton.com
81
IQ 100 Series (130/140/150) Meter
App B: Modbus Map
Floating Point Values
Floating Point Values are represented in the following format:
0
Register
Byte
1
0
1
0
1
Bit
7 6
5
4
3
2
1 0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Meaning
s
e
e
e
e
e
e
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
e
sign
e
exponent
mantissa
The formula to interpret a Floating Point Value is: -1sign x 2
-1sign x 2 137-127 x 1• 1000010001110110111001
-1 x 210 x 1.75871956
-1800.929
x1.mantissa = 0x0C4E11DB9
exponent-127
0x0C4E1
Register
Byte
0x01DB9
0x0C4
0x0E1
0x01D
0x0B9
Bit
7 6
5
4
3
2
1 0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Meaning
s
e
e
e
e
e
e
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
e
e
sign
exponent
mantissa
1
0x089 + 137
0b011000010001110110111001
Formula Explanation:
C4E11DB9 (hex)
11000100 11100001 00011101 10111001 (binary)
The sign of the mantissa (and therefore the number) is 1, which represents a negative
value.
The Exponent is 10001001 (binary) or 137 decimal.
The Exponent is a value in excess 127. So, the Exponent value is 10.
The Mantissa is 11000010001110110111001 binary.
With the implied leading 1, the Mantissa is (1).C23B72 (hex).
The Floating Point Representation is therefore -1.75871956 times 2 to the 10.
Decimal equivalent: -1800.929
NOTES: • Exponent = the whole number before the decimal point.
• Mantissa = the positive fraction after the decimal point.
82
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series ((130/140/150) Meter
App B: Modbus Map
Important Note Concerning the IQ 100 Series Modbus Map
In depicting Modbus Registers (Addresses), the IQ 100 Series meter’s Modbus map uses Holding
Registers only.
Hex Representation
The representation shown in the table below is used by developers of Modbus drivers and libraries, SEL
2020/2030 programmers and Firmware Developers. The meter’s Modbus map also uses this representation.
Hex Description
0008 – 000FMeter Serial Number
Decimal Representation
The meter’s Modbus map defines Holding Registers as (4X) registers. Many popular SCADA and HMI
packages and their Modbus drivers have user interfaces that require users to enter these Registers starting at 40001. So instead of entering two separate values, one for register type and one for the actual
register, they have been combined into one number.
The meter’s Modbus map uses a shorthand version to depict the decimal fields -i.e., not all of the digits
required for entry into the SCADA package UI are shown.
For example:
You need to display the meter’s serial number in your SCADA application. The meter’s Modbus map
shows the following information for meter serial number:
Decimal
9 – 16
Description
Meter Serial Number
In order to retrieve the meter’s serial number, enter 40009 into the SCADA UI as the starting register,
and 8 as the number of registers.
• In order to work with SCADA and Driver packages that use the 40001 to 49999 method for requesting holding registers, take 40000 and add the value of the register (Address) in the decimal column of
the Modbus Map. Then enter the number (e.g., 4009) into the UI as the starting register.
• For SCADA and Driver packages that use the 400001 to 465536 method for requesting holding registers take 400000 and add the value of the register (Address) in the decimal column of the Modbus
Map. Then enter the number (e.g., 400009) into the UI as the starting register. The drivers for these
packages strip off the leading four and subtract 1 from the remaining value. This final value is used
as the starting register or register to be included when building the actual modbus message.
Modbus Register Map (MM-1 to MM-16)
The IQ 100 Series Modbus register map begins on the following page.
User and Installation Manual IM02601003E - September 2011 www.eaton.com
83
IQ 100 Series (130/140/150) Meter
App B: Modbus Map
84
User and Installation Manual IM02601003E-September 2011 www.eaton.com
IQ 100 Series (130/140/150) Meter
Appendix B: Modbus Map
Modbus Address
Hex
Description1
Decimal
Units or
Resolution
Range6
Format
#
Reg
Comments
Fixed Data Section
Identification Block
0000 - 0007
0008 - 000F
0010 - 0010
read-only
1 - 8
9 - 16
17 - 17
Reserved
Meter Serial Number
Meter Type
ASCII
UINT16
16 char
bit-mapped
none
none
-------t --------
0011 - 0012
0013 - 0013
0014 - 0014
18 - 19
20 - 20
21 - 21
Firmware Version
Map Version
Meter Configuration
ASCII
UINT16
UINT16
4 char
0 to 65535
bit-mapped
none
none
-------- --ffffff
0015 - 0015
0016 - 0026
0027 - 002E
22 - 22
23 - 39
40 - 47
ASIC Version
Reserved
Reserved
UINT16
0-65535
none
8
8
1
t = transducer model (1=yes, 0=no)
2
1
1
ffffff = calibration frequency (50 or 60)
Block Size:
1
17
8
47
Meter Data Section 2
Primary Readings Block, 6 cycles (IEEE Floating Point)
read-only
0383 - 0384
900 - 901
Watts, 3-Ph total
FLOAT
-9999 M to +9999 M
watts
2
0385 - 0386
902 - 903
VARs, 3-Ph total
FLOAT
-9999 M to +9999 M
VARs
2
0387 - 0388
904 - 905
VAs, 3-Ph total
FLOAT
-9999 M to +9999 M
VAs
2
Block Size:
Primary Readings Block, 60 cycles (IEEE Floating Point)
03E7 - 03E8
1000 - 1001
Volts A-N
03E9 - 03EA
1002 - 1003
Volts B-N
03EB - 03EC
1004 - 1005
Volts C-N
03ED - 03EE
1006 - 1007
Volts A-B
03EF - 03F0
1008 - 1009
Volts B-C
03F1 - 03F2
1010 - 1011
Volts C-A
03F3 - 03F4
1012 - 1013
Amps A
03F5 - 03F6
1014 - 1015
Amps B
03F7 - 03F8
1016 - 1017
Amps C
03F9 - 03FA
1018 - 1019
Watts, 3-Ph total
03FB - 03FC
1020 - 1021
VARs, 3-Ph total
03FD - 03FE
1022 - 1023
VAs, 3-Ph total
03FF - 0400
1024 - 1025
Power Factor, 3-Ph total
0401 - 0402
1026 - 1027
Frequency
User and Installation Manual
6
read-only
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to 9999 M
-9999 M to +9999 M
-9999 M to +9999 M
-9999 M to +9999 M
-1.00 to +1.00
0 to 65.00
IM02601003E -September 2011
volts
volts
volts
volts
volts
volts
amps
amps
amps
watts
VARs
VAs
none
Hz
2
2
2
2
2
2
2
2
2
2
2
2
2
2
MM-1
IQ 100 Series (130/140/150) Meter
Appendix B: Modbus Map
Modbus Address
Hex
Decimal
0403 - 0404
1028 - 1029
Description1
Neutral Current
Format
FLOAT
Units or
Resolution
Range6
0 to 9999 M
#
Reg
Comments
amps
Block Size:
Primary Energy Block
044B - 044C
1100 - 1101
2
30
read-only
W-hours, Received
SINT32
044D - 044E
1102 - 1103
W-hours, Delivered
SINT32
044F - 0450
0451 - 0452
0453 - 0454
1104 - 1105
1106 - 1107
1108 - 1109
W-hours, Net
W-hours, Total
VAR-hours, Positive
SINT32
SINT32
SINT32
0455 - 0456
1110 - 1111
VAR-hours, Negative
SINT32
0457 - 0458
1112 - 1113
VAR-hours, Net
0459 - 045A
1114 - 1115
045B - 045C
1116 - 1117
0 to 99999999 or
0 to -99999999
0 to 99999999 or
0 to -99999999
-99999999 to 99999999
0 to 99999999
0 to 99999999
Wh per energy format
Wh per energy format
* Wh received & delivered always have
opposite signs
* Wh received is positive for "view as load",
delivered is positive for "view as generator"
2
2
SINT32
Wh per energy format
Wh per energy format
* 5 to 8 digits
VARh per energy format
* decimal point implied, per energy format
0 to -99999999
VARh per energy format
* resolution of digit before decimal point =
-99999999 to 99999999 VARh per energy format units, kilo, or mega, per energy format
2
VAR-hours, Total
SINT32
0 to 99999999
VARh per energy format
2
VA-hours, Total
SINT32
0 to 99999999
VAh per energy format
User and Installation Manual
18
read-only
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
0 to 9999 M
0 to 9999 M
0 to 9999 M
-9999 M to +9999 M
-9999 M to +9999 M
-9999 M to +9999 M
-9999 M to +9999 M
-9999 M to +9999 M
-1.00 to +1.00
-1.00 to +1.00
amps
amps
amps
watts
VARs
watts
VARs
VAs
none
none
Block Size:
Primary Minimum Block (IEEE Floating Point)
0BB7 - 0BB8
3000 - 3001
Volts A-N, Minimum
0BB9 - 0BBA
3002 - 3003
Volts B-N, Minimum
0BBB - 0BBC
3004 - 3005
Volts C-N, Minimum
0BBD - 0BBE
3006 - 3007
Volts A-B, Minimum
0BBF - 0BC0
3008 - 3009
Volts B-C, Minimum
2
2
* see note 10
Block Size:
Primary Demand Block (IEEE Floating Point)
07CF - 07D0
2000 - 2001
Amps A, Average
07D1 - 07D2
2002 - 2003
Amps B, Average
07D3 - 07D4
2004 - 2005
Amps C, Average
07D5 - 07D6
2006 - 2007
Positive Watts, 3-Ph, Average
07D7 - 07D8
2008 - 2009
Positive VARs, 3-Ph, Average
07D9 - 07DA
2010 - 2011
Negative Watts, 3-Ph, Average
07DB - 07DC
2012 - 2013
Negative VARs, 3-Ph, Average
07DD - 07DE
2014 - 2015
VAs, 3-Ph, Average
07DF - 07E0
2016 - 2017
Positive PF, 3-Ph, Average
07E1 - 07E2
2018 - 2019
Negative PF, 3-PF, Average
2
2
2
2
2
2
2
2
2
2
2
2
2
20
read-only
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to 9999 M
IM02601003E -September 2011
volts
volts
volts
volts
volts
2
2
2
2
2
MM-2
IQ 100 Series (130/140/150) Meter
Appendix B: Modbus Map
Modbus Address
Hex
0BC1
0BC3
0BC5
0BC7
0BC9
0BCB
0BCD
0BCF
0BD1
0BD3
0BD5
0BD7
-
0BC2
0BC4
0BC6
0BC8
0BCA
0BCC
0BCE
0BD0
0BD2
0BD4
0BD6
0BD8
Description1
Decimal
3010
3012
3014
3016
3018
3020
3022
3024
3026
3028
3030
3032
-
3011
3013
3015
3017
3019
3021
3023
3025
3027
3029
3031
3033
Format
Volts C-A, Minimum
Amps A, Minimum Avg Demand
Amps B, Minimum Avg Demand
Amps C, Minimum Avg Demand
Positive Watts, 3-Ph, Minimum Avg Demand
Positive VARs, 3-Ph, Minimum Avg Demand
Negative Watts, 3-Ph, Minimum Avg Demand
Negative VARs, 3-Ph, Minimum Avg Demand
VAs, 3-Ph, Minimum Avg Demand
Positive Power Factor, 3-Ph, Minimum Avg Demand
Negative Power Factor, 3-Ph, Minimum Avg Demand
Frequency, Minimum
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
Range6
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to +9999 M
0 to +9999 M
0 to +9999 M
0 to +9999 M
-9999 M to +9999 M
-1.00 to +1.00
-1.00 to +1.00
0 to 65.00
Units or
Resolution
#
Reg
Comments
volts
amps
amps
amps
watts
VARs
watts
VARs
VAs
none
none
Hz
Block Size:
Primary Maximum Block (IEEE Floating Point)
0C1B - 0C1C
3100 - 3101
Volts A-N, Maximum
0C1D - 0C1E
3102 - 3103
Volts B-N, Maximum
0C1F - 0C20
3104 - 3105
Volts C-N, Maximum
0C21 - 0C22
3106 - 3107
Volts A-B, Maximum
0C23 - 0C24
3108 - 3109
Volts B-C, Maximum
0C25 - 0C26
3110 - 3111
Volts C-A, Maximum
0C27 - 0C28
3112 - 3113
Amps A, Maximum Avg Demand
0C29 - 0C2A
3114 - 3115
Amps B, Maximum Avg Demand
0C2B - 0C2C
3116 - 3117
Amps C, Maximum Avg Demand
0C2D - 0C2E
3118 - 3119
Positive Watts, 3-Ph, Maximum Avg Demand
0C2F - 0C30
3120 - 3121
Positive VARs, 3-Ph, Maximum Avg Demand
0C31 - 0C32
3122 - 3123
Negative Watts, 3-Ph, Maximum Avg Demand
0C33 - 0C34
3124 - 3125
Negative VARs, 3-Ph, Maximum Avg Demand
0C35 - 0C36
3126 - 3127
VAs, 3-Ph, Maximum Avg Demand
0C37 - 0C38
3128 - 3129
Positive Power Factor, 3-Ph, Maximum Avg Demand
0C39 - 0C3A
3130 - 3131
Negative Power Factor, 3-Ph, Maximum Avg Demand
0C3B - 0C3C
3132 - 3133
Frequency, Maximum
read-only
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
FLOAT
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to 9999 M
0 to +9999 M
0 to +9999 M
0 to +9999 M
0 to +9999 M
-9999 M to +9999 M
-1.00 to +1.00
-1.00 to +1.00
FLOAT
0 to 65.00
volts
volts
volts
volts
volts
volts
amps
amps
amps
watts
VARs
watts
VARs
VAs
none
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
none
Hz
Block Size:
Reserved Block7, 13
0F9F - 0F9F
0FA0 - 0FA0
0FA1 - 0FA1
0FA2 - 0FA2
2
2
2
2
2
2
2
2
2
2
2
2
34
2
34
read-only
4000
4001
4002
4003
-
4000
4001
4002
4003
Reserved
Reserved
Reserved
Reserved
User and Installation Manual
UINT16
UINT16
UINT16
UINT16
0 to 9999, or 65535
0 to 9999, or 65535
0 to 9999, or 65535
0 to 9999, or 65535
IM02601003E -September 2011
0.1%
0.1%
0.1%
0.1%
1
1
1
1
MM-3
IQ 100 Series (130/140/150) Meter
Appendix B: Modbus Map
Modbus Address
Hex
0FA3
0FA4
0FA5
0FA6
0FA7
0FA8
0FA9
0FAA
0FAB
0FAC
0FAD
0FAE
0FAF
0FB0
0FB1
-
0FA3
0FA4
0FA5
0FA6
0FA7
0FA8
0FA9
0FAA
0FAB
0FAC
0FAD
0FAE
0FAF
0FB0
0FB8
Description1
Decimal
4004
4005
4006
4007
4008
4009
4010
4011
4012
4013
4014
4015
4016
4017
4018
-
4004
4005
4006
4007
4008
4009
4010
4011
4012
4013
4014
4015
4016
4017
4025
Format
Range6
Units or
Resolution
#
Reg
Comments
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
1
1
1
1
1
1
1
1
1
1
1
1
1
1
8
0FB9 - 0FBC
4026 - 4029
Reserved
4
0FBD - 0FC4
4030 - 4037
Reserved
8
0FC5 - 0FC8
4038 - 4041
Reserved
4
Block Size:
Phase Angle Block14
1003 - 1003
4100
1004 - 1004
4101
1005 - 1005
4102
1006 - 1006
4103
1007 - 1007
4104
1008 - 1008
4105
42
read-only
-
4100
4101
4102
4103
4104
4105
Phase A Current
Phase B Current
Phase C Current
Angle, Volts A-B
Angle, Volts B-C
Angle, Volts C-A
SINT16
SINT16
SINT16
SINT16
SINT16
SINT16
-1800 to +1800
-1800 to +1800
-1800 to +1800
-1800 to +1800
-1800 to +1800
-1800 to +1800
0.1 degree
0.1 degree
0.1 degree
0.1 degree
0.1 degree
0.1 degree
Block Size:
Status Block
1387 - 1387
5000 - 5000
Meter Status
UINT16
bit-mapped
--exnpch ssssssss
1388 - 1388
1389 - 138A
5001 - 5001
5002 - 5003
Reserved
Time Since Reset
UINT32
0 to 4294967294
4 msec
read-only
exnpch = EEPROM block OK flags
(e=energy, x=max, n=min, p=programmable
settings, c=calibration, h=header),
ssssssss = state (1=Run, 2=Limp, 10=Prog
Set Update via buttons, 12=Prog Set
Update via COM2)
wraps around after max coun
Block Size:
User and Installation Manual
IM02601003E -September 2011
MM-4
1
1
1
1
1
1
6
1
1
2
4
IQ 100 Series (130/140/150) Meter
Appendix B: Modbus Map
Modbus Address
Hex
Description1
Decimal
Format
Range6
Units or
Resolution
#
Reg
Comments
Commands Section 4
write-only
9
Resets Block
4E1F - 4E1F
4E20 - 4E20
20000 - 20000
20001 - 20001
Reset Max/Min Blocks
Reset Energy Accumulators
UINT16
UINT16
password5
password5
Block Size:
Meter Programming Block
55EF - 55EF
22000 - 22000
55F0 - 55F0
22001 - 22001
Initiate Programmable Settings Update
3
Terminate Programmable Settings Update
UINT16
UINT16
55F1 - 55F1
22002 - 22002
3
Calculate Programmable Settings Checksum
UINT16
55F2 - 55F2
22003 - 22003
Programmable Settings Checksum3
UINT16
55F3 - 55F3
22004 - 22004
Write New Password3
UINT16
read/conditional write
meter enters PS update mode
5
password
any value
meter leaves PS update mode via reset
meter calculates checksum on RAM copy
of PS block
read/write checksum register; PS block
saved in EEPROM on write8
0000 to 9999
1
1
2
1
1
1
1
1
write-only register; always reads zero
59D7 - 59D7
23000 - 23000
Initiate Meter Firmware Reprogramming
UINT16
password5
Block Size:
Other Commands Block
61A7 - 61A7
25000 - 25000
read/write
Force Meter Restart
UINT16
password5
1
causes a watchdog reset, always reads 0
Block Size:
Encryption Block
658F - 659A
26000 - 26011
1
6
Perform a Secure Operation
read/write
encrypted command to read password or
change meter type
Block Size:
UINT16
1
12
12
Programmable Settings Section
Basic Setups Block
752F - 752F
30000 - 30000
CT multiplier & denominator
UINT16
bit-mapped
dddddddd mmmmmmmm
7530 - 7530
7531 - 7531
7532 - 7532
30001 - 30001
30002 - 30002
30003 - 30003
CT numerator
PT numerator
PT denominator
UINT16
UINT16
UINT16
1 to 9999
1 to 9999
1 to 9999
none
none
none
User and Installation Manual
IM02601003E -September 2011
write only in PS update mode
high byte is denominator (1 or 5, read-only),
low byte is multiplier (1, 10, or 100)
1
1
1
1
MM-5
IQ 100 Series (130/140/150) Meter
Appendix B: Modbus Map
Modbus Address
Description1
Range6
Units or
Resolution
#
Reg
Hex
Decimal
7533 - 7533
30004 - 30004
PT multiplier & hookup
UINT16
bit-mapped
mmmmmmmm MMMMhhhh
MMMMmmmmmmmm is PT multiplier (1,
10, 100, 1000),
hhhh is hookup enumeration (0 = 3 element
wye[9S], 1 = delta 2 CTs[5S], 3 = 2.5
element wye[6S])
1
7534 - 7534
30005 - 30005
Averaging Method
UINT16
bit-mapped
--iiiiii b----sss
iiiiii = interval (5,15,30,60)
b = 0-block or 1-rolling
sss = # subintervals (1,2,3,4)
1
7535 - 7535
30006 - 30006
Power & Energy Format
UINT16
bit-mapped
pppp--nn -eee-ddd
pppp = power scale (0-unit, 3-kilo, 6-mega,
8-auto)
nn = number of energy digits (5-8 --> 0-3)
eee = energy scale (0-unit, 3-kilo, 6-mega)
ddd = energy digits after decimal point (0-6)
See note 10.
1
7536 - 7536
30007 - 30007
Operating Mode Screen Enables
UINT16
bit-mapped
00000000 eeeeeeee
eeeeeeee = op mode screen rows on(1) or
off(0), rows top to bottom are bits low order
to high order
1
7537 - 753D
753E - 753E
30008 - 30014
30015 - 30015
Reserved
User Settings Flags
UINT16
bit-mapped
---g--nn srp--wf-
g = enable alternate full scale bargraph
current (1=on, 0=off)
nn = number of phases for voltage &
current screens (3=ABC, 2=AB, 1=A,
0=ABC)
s = scroll (1=on, 0=off)
r = password for reset in use (1=on, 0=off)
p = password for configuration in use
(1=on, 0=off)
w = pwr dir (0-view as load, 1-view as
generator)
f = flip power factor sign (1=yes, 0=no)
753F - 753F
30016 - 30016
Full Scale Current (for load % bargraph)
UINT16
0 to 9999
none
If non-zero and user settings bit g is set,
this value replaces CT numerator in the full
scale current calculation.
7540 - 7547
30017 - 30024
Meter Designation
ASCII
16 char
none
User and Installation Manual
Format
IM02601003E -September 2011
Comments
7
1
1
8
MM-6
IQ 100 Series (130/140/150) Meter
Appendix B: Modbus Map
Modbus Address
Description1
Hex
Decimal
7548 - 7548
7549 - 7549
30025 - 30025
30026 - 30026
Reserved
COM2 setup
754A
754B
754C
754D
754E
754F
7550
7555
755A
755F
7564
7569
756E
30027
30028
30029
30030
30031
30032
30033
30038
30043
30048
30053
30058
30063
COM2 address
Reserved
Reserved
Reserved
Reserved
Reserved
-
754A
754B
754C
754D
754E
754F
7554
7559
755E
7563
7568
756D
7572
-
30027
30028
30029
30030
30031
30032
30037
30042
30047
30052
30057
30062
30067
Format
Units or
Resolution
Range6
UINT16
bit-mapped
----dddd -ppp-bbb
UINT16
1 to 247
none
#
Reg
Comments
dddd = reply delay (* 50 msec)
ppp = protocol (1-Modbus RTU, 2-Modbus
ASCII, 3-DNP)
Block Size:
1
1
1
1
1
1
1
1
5
5
5
5
5
5
5
68
12-Bit RTU Readings Section
12-Bit RTU Block
9C40
9C41
9C42
9C43
9C44
9C45
9C46
9C47
9C48
9C49
9C4A
-
9C40
9C41
9C42
9C43
9C44
9C45
9C46
9C47
9C48
9C49
9C4A
40001
40002
40003
40004
40005
40006
40007
40008
40009
40010
40011
-
40001
40002
40003
40004
40005
40006
40007
40008
40009
40010
40011
System Sanity Indicator
Volts A-N
Volts B-N
Volts C-N
Amps A
Amps B
Amps C
Watts, 3-Ph total
VARs, 3-Ph total
VAs, 3-Ph total
Power Factor, 3-Ph total
UINT16
UINT16
UINT16
UINT16
UINT16
UINT16
UINT16
UINT16
UINT16
UINT16
UINT16
0 or 1
2047 to 4095
2047 to 4095
2047 to 4095
0 to 4095
0 to 4095
0 to 4095
0 to 4095
0 to 4095
2047 to 4095
1047 to 3047
none
volts
volts
volts
amps
amps
amps
watts
VARs
VAs
none
9C4B - 9C4B
40012 - 40012
Frequency
UINT16
0 to 2730
Hz
9C4C - 9C4C
9C4D - 9C4D
9C4E - 9C4E
40013 - 40013
40014 - 40014
40015 - 40015
Volts A-B
Volts B-C
Volts C-A
UINT16
UINT16
UINT16
2047 to 4095
2047 to 4095
2047 to 4095
volts
volts
volts
User and Installation Manual
IM02601003E -September 2011
read-only except as noted
0 indicates proper meter operatio
2047= 0, 4095= +150
volts = 150 * (register - 2047) / 2047
0= -10, 2047= 0, 4095= +10
amps = 10 * (register - 2047) / 2047
0= -3000, 2047= 0, 4095= +3000
watts, VARs, VAs =
3000 * (register - 2047) / 2047
1047= -1, 2047= 0, 3047= +1
pf = (register - 2047) / 1000
0= 45 or less, 2047= 60, 2730= 65 or more
freq = 45 + ((register / 4095) * 30)
2047= 0, 4095= +300
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
volts = 300 * (register - 2047) / 2047
MM-7
IQ 100 Series (130/140/150) Meter
Appendix B: Modbus Map
Modbus Address
Hex
9C4F
9C50
9C51
9C52
9C53
9C54
9C55
9C57
-
9C4F
9C50
9C51
9C52
9C53
9C54
9C56
9C58
Description1
Decimal
40016
40017
40018
40019
40020
40021
40022
40024
-
40016
40017
40018
40019
40020
40021
40023
40025
6
Format
Range
Units or
Resolution
#
Reg
Comments
CT numerator
CT multiplier
CT denominator
PT numerator
PT multiplier
PT denominator
W-hours, Positive
W-hours, Negative
UINT16
UINT16
UINT16
UINT16
UINT16
UINT16
UINT32
UINT32
1 to 9999
1, 10, 100
1 or 5
1 to 9999
1, 10, 100
1 to 9999
0 to 99999999
0 to 99999999
none
none
none
none
none
none
Wh per energy format
Wh per energy format
VAR-hours, Positive
UINT32
0 to 99999999
VARh per energy format
2
2
2
CT = numerator * multiplier / denominator
PT = numerator * multiplier / denominator
* 5 to 8 digits
1
1
1
1
1
1
2
2
* decimal point implied, per energy format
9C59 - 9C5A
40026 - 40027
9C5B - 9C5C
40028 - 40029
VAR-hours, Negative
UINT32
0 to 99999999
* resolution of digit before decimal point =
VARh per energy format units, kilo, or mega, per energy format
9C5D - 9C5E
40030 - 40031
VA-hours
UINT32
0 to 99999999
VAh per energy format
9C5F - 9C5F
9C60 - 9CA2
9CA3 - 9CA3
40032 - 40032
40033 - 40099
40100 - 40100
Neutral Current
Reserved
Reset Energy Accumulators
UINT16
N/A
UINT16
0 to 4095
N/A
amps
none
password5
* see note 10
1
67
1
see Amps A/B/C above
write-only register; always reads as 0
Block Size:
100
End of Map
Data Formats
ASCII
SINT16 / UINT16
SINT32 / UINT32
FLOAT
Notes
1
2
ASCII characters packed 2 per register in high, low order and without any termination characters.
16-bit signed / unsigned integer.
32-bit signed / unsigned integer spanning 2 registers. The lower-addressed register is the high order half.
32-bit IEEE floating point number spanning 2 registers. The lower-addressed register is the high order half (i.e., contains the exponent).
All registers not explicitly listed in the table read as 0. Writes to these registers will be accepted but won't actually change the register (since it doesn't exist).
Meter Data Section items read as 0 until first readings are available or if the meter is not in operating mode. Writes to these registers will be accepted but won't actually change the register.
3
4
Register valid only in programmable settings update mode. In other modes these registers read as 0 and return an illegal data address exception if a write is attempted.
Meter command registers always read as 0. They may be written only when the meter is in a suitable mode. The registers return an illegal data address exception if a write is attempted in an incorrect
mode.
5
If the password is incorrect, a valid response is returned but the command is not executed. Use 5555 for the password if passwords are disabled in the programmable settings.
User and Installation Manual
IM02601003E -September 2011
MM-8
IQ 100 Series (130/140/150) Meter
Appendix B: Modbus Map
(continued)
6
7
8
M denotes a 1,000,000 multiplier.
Not used.
Writing this register causes data to be saved permanently in EEPROM. If there is an error while saving, a slave device failure exception is returned and programmable settings mode automatically
terminates via reset.
9
10
11
12
13
14
Reset commands make no sense if the meter state is LIMP. An illegal function exception will be returned.
Energy registers should be reset after a format change.
Not used.
Not used.
Not used.
All 3 voltage angles are measured for Wye and Delta hookups. For 2.5 Element, Vac is measured and Vab & Vbc are calculated. If a voltage phase is missing, the two voltage angles in which it
participates are set to zero. A and C phase current angles are measured for all hookups. B phase current angle is measured for Wye and is zero for other hookups. If a voltage phase is missing, its cu
angle is zero.
15
If any register in the programmable settings section is set to a value other than the acceptable value then the meter will stay in LIMP mode. Please read the comments section or the range for each register
in programmable settings section for acceptable values.
User and Installation Manual
IM02601003E -September 2011
MM-9
IQ 100 Series (130/140/150) Meter
User and Installation Manual
Appendix B: Modbus Map
IM02601003E -September 2011
MM-10
Download PDF