Belkin | AP30800-10 | User manual | Belkin AP30800-10 User manual

Clean Sound
Clear Picture
Home Theater Battery Backup with AVR Technology
User Manual
AP30800-10
Table of Contents
Page
PureAV Battery Backup
Introduction ......................................................................................... 2
Package Contents ............................................................................... 2
PureAV Battery Backup Features and Functions ........................3
Alarms .................................................................................................. 4
Product Features .......................................................................... 5
Installation ................................................................................ 6-7
Troubleshooting ............................................................................. 8
Technical Specifications .............................................................. 9
Storage ........................................................................................... 9
Belkin Connected Equipment Warranty ................................ 10-12
Information ................................................................................... 13
1
Introduction
PureAV Battery Backup
Congratulations and thank you for purchasing the PureAV Home Theater
Battery Backup with AVR Technology (the PureAV Battery Backup).
Frequent electrical disturbances, both natural and man-made, degrade
the quality of power supplied to your home theater system. Brownouts
or blackouts can cause you to lose your complex settings, and ultimately
damage your valuable equipment along with the overall quality of your
home theater experience. In addition to providing battery power in case
of a blackout, our PureAV Battery Backup provides outstanding surge
protection and power conditioning while ensuring that you experience the
clearest picture and cleanest sound directly from the source.
Please save this manual!
It contains important operating instructions and warranty information
pertaining to your PureAV Battery Backup.
Please save or recycle the packaging materials
The PureAV Battery Backup packaging was designed with great care to
provide protection during shipment and delivery. Please keep the packaging
materials in the unlikely event that you must return this product for service.
Damage sustained during transit is not covered under the warranty.
Package Contents
You should have received the following:
• 1 PureAV Battery Backup unit
• 2 rackmount Brackets
• 1 Network Line Cable
• 1 Phone Line Cable
• 1 Coaxial Cable
2
PureAV Battery Backup Features and Functions
PureAV Battery Backup
On/Off/Test Switch
LEDs Indicator
Site Wiring Fault
Battery On
Replace Battery
Overload
Battery
Load
Indicator
BATTERY ON
(Green LED)
Condition
Solid
Green
Flashing
Green
OVERLOAD
(Yellow LED)
Solid
Yellow
Flashing
Yellow
REPLACE
BATTERY
(Red LED)
SITE WIRING
FAULT
(Red LED)
LOAD
(Yellow LED)
BATTERY
(Green LED)
3
Solid
Red
Solid
Red
Meaning
The PureAV Battery Backup is on battery
back-up mode and an Intermittent audible
alarm is on. The Battery Backup will begin
shutdown procedure.
Battery is low. The PureAV Battery Backup
will start shutdown. The buzzer sounds an
audible alarm.
The PureAV Battery Backup shutdown due to an
overload or short-circuit condition.
Battery output is drawing more power than the
Battery Backup can provide.
Battery is weak or bad; the battery needs
to be replaced.
There is either no ground circuit or a
reversed polarity in the building wiring.
Solid
Yellow
This display shows the PureAV Battery Backup
output load percentage level of 17%, 33%,
50%, 67%, and 85%.
Solid
Green
This display shows the battery capacity
percentage level of 20%, 40%, 60%, 80%, and
100%.
Alarms
Low Battery (Rapid Alarm)
When the PureAV Battery Backup is in battery-backup mode and the
battery’s energy begins to run low, the PureAV Battery Backup will beep
rapidly until it shuts down from a depleted battery or returns to online
normal operation.
PureAV Battery Backup
Battery Backup (Slow Alarm)
When the PureAV Battery Backup is in battery-backup mode, the “Battery
On” LED (green) illuminates and the PureAV Battery Backup sounds an
audible alarm. The alarm stops when the PureAV Battery Backup returns
to normal online operation.
Overload (Continuous alarm)
When the PureAV Battery Backup is overloaded (the connected loads
exceed the maximum rated capacity), the PureAV Battery Backup
emits a continuous alarm to warn of an overload condition. Disconnect
nonessential equipment from the PureAV Battery Backup to eliminate
the overload.
4
Product Features
PureAV Battery Backup
B
A
D
H
G
C
E
F
Rear Panel
A. Surge-Protection-Only Outlets
Equipment such as printers, fax machines, scanners, or desk lamps can
be plugged into these outlets. These outlets do not provide power
during a power outage. These outlets are always on (when AC power is
available) and are not controlled by the front-panel switch.
B. Battery-Backup Surge-Protection Outlets
Only critical equipment such as TVs, DVRs, cable/satellite receivers,
VCRs, and other hardware that could potentially lose settings should be
plugged into these outlets. Battery power is automatically provided
in case of a power outage. Power (AC or battery) is not supplied to
these outlets when the PureAV Battery Backup is switched off. (Do not
plug surge protectors or power strips into the battery backup outlets).
Note! During the AVR Mode, the total load that you will be placing
on the battery-backup outlets should not exceed 85% of the
unit’s capacity.
C. Phone Protection
The phone lines are surge protected and provide complete safety for
telephone/Pay-Per-View lines.
D. Network Protection
This connector is used for surge protecting networking lines used for
media streamers, multimedia computers, gaming consoles, or any other
device in need of a network connection.
E. AC Input Breaker (Circuit Breaker)
The circuit breaker button will be triggered if an overload condition
forces the PureAV Battery Backup to disconnect itself from utility
power. If the button sticks out, disconnect nonessential equipment
and depress
breaker to reset.
F. AC Input Power Cord
G. Audio Video Surge Protection Ports
H. Alert Sound ON/OFF Switch
This switch turns the audible alarm ON or OFF.
5
Installation
Connect To AC Utility Power
Connect the AC inlet to utility power via the power cord. Check whether
the “Site Wiring Fault” indicator is lit or not. If so, please check the
utility wiring.
Charging The Battery
For best results, charge the battery for eight hours prior to initial use. The
PureAV Battery Backup charges its battery whenever it is connected to the
utility power.
PureAV Battery Backup
Note!
Before installation, please inspect the PureAV Battery Backup upon receipt
to make sure it is not damaged.
Plug In Power Devices
Plug your devices into the AC outlets on the rear of the PureAV Battery
Backup. To use the PureAV Battery Backup as a master on/off switch, make
sure all of the loads are switched on.
Caution: Never connect a laser printer or scanner to the
battery backup outlets of the PureAV Battery Backup. A laser printer
or scanner draws significantly more power when in use than when idle.
This may overload the PureAV Battery Backup.
Turning On The PureAV Battery Backup
Turn on your PureAV Battery Backup by pressing and holding the
“On/Off/Test” button for approximately two seconds until the green “ON
LINE” light comes on.
Turning Off The PureAV Battery Backup
Turn off the PureAV Battery Backup by pressing and holding the
“On/Off/Test” button for more than two seconds until the “ON LINE” or
“ON BATTERY” light goes off.
To Conduct a Self-test
Use the self-test to verify both the operation of the PureAV Battery Backup
and the condition of the battery. In normal utility power, push the “On/Off/
Test” button less than 1.5 seconds and the PureAV Battery Backup performs
a self-test function. During the self-test, the PureAV Battery Backup
operates in backup mode.
Note! During the self-test, the PureAV Battery Backup briefly
operates on battery-backup power (the “ON BATTERY” LED comes
on). If the PureAV Battery Backup passes the self-test, it returns to
online operation. If the PureAV Battery Backup fails the self-test, it
immediately returns to online operation and lights the “REPLACE
BATTERY” LED. The loads are not affected. Recharge the battery
overnight and perform the self-test again. If the “REPLACE BATTERY”
LED is still on, the battery will need to be replaced. Please contact
Belkin Customer Service for assistance.
6
Installation
PureAV Battery Backup
To Silence Audible Alarm
There are two ways to disable the audible alarm:
1. Set the Alert Sound ON/OFF Switch to the OFF position. When in
the OFF position, the audible alarm will not sound when the PureAV
Battery Backup is in the backup mode.
2. While in battery-backup mode, push the “ON/OFF/TEST” button less
than 1.5 seconds to silence the audible alarm. (This does not work if the
PureAV Battery Backup is under low-battery or overload condition.)
All equipment must be turned off prior to hardware installation.
Phone/Fax/Modem
Telephone Socket
Connect The Phone/Fax/Modem/Lines
Connect a single phone/fax/modem line into the surge-protected sockets
on the back of the PureAV Battery Backup. The RJ11 modular sockets
accept standard single-line telephone connections. The connection will
require another length of telephone cable, which is supplied.
Note! This connection is optional but highly suggested as phone/fax/
modem lines often carry dangerous surges and spikes. The PureAV Battery
Backup works properly without a phone/fax/modem connection.
Caution! The phone/fax/modem protection feature could be rendered
inoperable if improperly installed. Make sure that the telephone line from
the wall is plugged into the connector marked “IN”, and the device to be
protected is plugged into the connector marked “ OUT”.
Connect The Network Line
Connect the network line from the wall to the connector marked “IN”,
then connect the device (Ethernet card) to be protected to the connector
marked “OUT”.
Connect Audio Video Coaxial Cable
Connect a modular coaxial cable between the cable wall outlet and the
surge protector jack marked “IN”. Connect another coaxial cable between
the surge protector jack marked “OUT” and the cable equipment or cable
modem being protected.
*All equipment must be turned off prior to hardware installation.
7
Troubleshooting
Solution
On/Off/Test button not
pushed or pushed less
than 2 seconds
Press the On/Off/Test
button for more than 2
seconds
Battery voltage is too
low
Recharge the Battery
Backup at least 8 hours
Battery Backup fault
Contact Belkin Customer
Service
Power cord loose
Re-plug the power cord
AC breaker is burned
out or tripped
Replace or reset the breaker
AC utility voltage is too
high or too low, or there
is a blackout
Normal condition
Battery not fully
charged
Recharge the Battery
Backup at least 8 hours
Battery Backup is
overloaded
Remove some unnecessary
loads
Charger fault or other
reason
Replace battery.
Contact Belkin Customer
Service or go to belkin.com.
The PureAV
Battery Backup
continuously beeps
Overload
Remove the non-critical
loads
Red LED lit
Battery failure
Replace battery.
Contact Belkin Customer
Service or go to belkin.com.
PureAV Battery
Backup not on,
LED not lit
PureAV
Battery Backup
always on battery
mode
Backup time
too short
PureAV Battery Backup
Possible Cause
Problem
8
Technical Specifications
Model
AP30800-10
PureAV Battery Backup
Capacity
1200VA/640W
Voltage Range
90-136VAC
Frequency
60Hz ( ±3Hz )
Voltage
Simulated sine wave,
120VAC ±8%
Frequency
(On Battery)
60Hz ( ±1Hz )
Backup time
15%-100% load
1.5~40 min.
Typical
Recharge Time
≤ 12 hours recover
85% capacity
ENVIRONMENT
Ambient
Operation
0~85% humidity
non-condensing, 0~35°C
CONFORMANCE
Surge
IEEE C62.41
Category A standard
Dimension
(W x H x D)
435mm x 88mm x 330mm
Net Weight
14.5kg.
INPUT
OUTPUT
BATTERY
PHYSICAL
All specifications are subject to change without prior notice.
Storage
Storage Conditions
Store the PureAV Battery Backup covered and upright in a cool, dry location
with its battery fully charged. Before storing, charge the PureAV Battery
Backup for at least four hours.
Extended Storage
During extended storage in environments where the ambient temperature is
+5 degrees to +86 degrees F, charge the PureAV Battery Backup’s battery
every six months. During extended storage in environments where the
ambient temperature is +86 degrees F to +113 degrees F, charge the PureAV
Battery Backup’s battery every three months.
9
Belkin Connected Equipment Warranty
Belkin Corporation will repair or replace, at its option, any equipment
which is damaged by a transient voltage surge/spike or lightning strike,
(an “Occurrence”), while properly connected through a PureAV Battery
Backup to a properly wired AC power line with protective ground. If you
are using an AC PureAV Battery Backup that has phone, network, or
coaxial protection, the telephone line, network line, and coaxial-cable line
must be properly connected and installed, as determined by Belkin at its
sole discretion.
PureAV Battery Backup
Belkin Corporation warrants to the original purchaser of any PureAV
Battery Backup for three years from the date of purchase, that the PureAV
Battery Backup shall be free of defects in design, assembly, material,
or workmanship, and will repair or replace, at its option, any defective
product free of charge.
This Connected Equipment Warranty is a Limited Warranty, subject to the
limitations and exclusions set forth herein.
Belkin Corporation will spend, to repair or replace the damaged connected
equipment, at Belkin’s option, an amount equal to the fair market value of
the damaged equipment or the original purchase price of the equipment,
whichever is less, up to the maximum amount set forth below:
Model AP30800-10
Up to a maximum of $500,000.00
The fair market value of the equipment shall be the current value of the
equipment specified in the most recent edition of the Orion Blue Book by
Orion Research Corporation, Roger Rohrs Publisher.
Belkin Corporation reserves the right to review the damaged PureAV
Battery Backup, the damaged equipment, and the site where the damage
occurred. All costs of shipping the PureAV Battery Backup and the
damaged equipment to Belkin Corporation for inspection shall be borne
solely by the purchaser. Belkin reserves the right to negotiate the cost of
repairs. If Belkin determines, in its sole discretion, that it is impractical to
ship the damaged equipment to Belkin Corporation, Belkin may designate,
in its sole discretion, an equipment repair facility to inspect and estimate
the cost to repair such equipment. The cost, if any, of shipping the
equipment to and from such repair facility and of such estimate shall be
borne solely by the purchaser. Damaged equipment must remain available
for inspection until the claim is finalized. Whenever claims are settled,
10
Belkin Connected Equipment Warranty
PureAV Battery Backup
Belkin Corporation reserves the right to be subrogated under any
existing insurance policies the claimant may have.
All above warranties are null and void if: the PureAV Battery Backup
in use during the occurrence is not provided to Belkin Corporation for
inspection upon Belkin’s request at the sole expense of the purchaser,
Belkin Corporation determines that the PureAV Battery Backup
has been improperly installed, altered in any way or tampered
with, Belkin Corporation determines that the damage did not result
from the Occurrence or that no Occurrence in fact took place, the
repair or replacement of the damaged equipment is covered under
a manufacturer’s warranty, or Belkin Corporation determines that
the connected equipment was not used under normal operating
conditions or in accordance with any labels or instructions. All
PureAV Battery Backups must be plugged directly into the power
source and must not be “daisy-chained” together in serial fashion
with other power strips, UPSes, other surge protectors or extension
cords. A 3–2-prong adapter may not be used. Any such installation
voids the warranty. The Belkin Connected Equipment Warranty only
protects against damage to properly connected equipment where
Belkin Corporation has determined, in its sole discretion, that the
damage resulted from an Occurrence, and does not protect against
acts of God (other than lightning) such as flood, earthquake, war,
vandalism, theft, normal-use wear and tear, erosion, depletion,
obsolescence, abuse, damage due to low voltage disturbances (i.e.
brownouts or sags), non-authorized program, or system equipment
modification or alteration. *Please note: This product is not for
use with aquariums and all other water-related products. Use only
indoors and in dry locations.
This warranty contains the sole warranty of Belkin Corporation,
there are no other warranties, expressed or, except as required by
law, implied, including the implied warranty or condition of quality,
merchantability or fitness for a particular purpose, and such implied
warranties, if any, are limited in duration to the term of this warranty.
Some states do not allow limitations on how long an implied warranty
lasts, so the above limitations may not apply to you.
In no event shall Belkin Corporation be liable for incidental, special,
direct, indirect, consequential or multiple damages such as, but not
limited to, lost business or profits arising out of the sale or use of
any PureAV Battery Backup, even if advised of the possibility of such
damages. This warranty gives you specific legal rights, and you may
11
Belkin Connected Equipment Warranty
This warranty is valid only for the original purchaser of the product. All
damage claims against the product must be made within 15 days from
the date of the Occurrence and must be accompanied by a receipt for
the damaged equipment or the warranty is void. Warranty is valid in USA,
Canada, Puerto Rico, and Bermuda. To file a claim against the Belkin
Connected Equipment Warranty, you must take the following steps: Contact
Belkin online at www.belkin.com and print our claim form or write to us at:
PureAV Battery Backup
also have other rights, which may vary from state to state. Some states do not
allow the exclusion or limitation of incidental or consequential damage, so the
above limitations may not apply to you.
Belkin Corporation, 501 W. Walnut St., Compton CA 90220
Attn: Technical Support, or call (310) 898-1100, extension 2263, within 15
days of the Occurrence. Be prepared to provide the following information:
a.
The part number of the PureAV Battery Backup.
b.
The equipment that was connected to the PureAV Battery Backup at
the time of the Occurrence.
c.
The equipment that was damaged during the Occurrence and the
extent of the damage.
d.
The date of the Occurrence.
e.
Where you purchased the PureAV Battery Backup.
f.
When you purchased the PureAV Battery Backup.
g.
Copy of original receipt.
h.
Your Belkin Customer Service Representative will then instruct you
on how to forward your equipment, receipt, PureAV Battery Backup in
use during the “Occurrence” and how to proceed with your claim.
Please conveniently register your PureAV Battery Backup online on our
website at www.belkin.com.
Belkin Corporation • 501 West Walnut Street • Compton • CA • 90220 • Tel:
310.898.1100 • Fax: 310.898.1111
12
Information
PureAV Battery Backup
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. To assure continued
compliance, use only shielded interface cables when connecting to
computer or peripheral devices. Any changes or modifications not
expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
SAFETY INFORMATION
CAUTION!
• Internal battery voltage is 12VDC.
• The unit is intended for installation in a controlled environment
(temperature controlled, indoor area free of conductive
contaminants).
• All batteries used are sealed lead batteries. Batteries must be
recycled.
Recycling Information
Your PureAV Battery Backup contains a non-spillable sealed lead
battery. On the battery, you will find the battery name. Please
reference the chart below for recycling information.
Battery Name
Recycling Inside
the USA
Recycling Outside
the USA
BB Battery
(800) 278-8599
N/A
CSB Battery
(800) 738-7372
1 (817) 244-4415
VISION Battery
(973) 726-5323
N/A
RITAR Battery
(888) 841-5179
N/A
Please visit belkin.com for battery replacement information
13
PureAV Battery Backup
14
www.pureav.com
Belkin Corporation
501 West Walnut Street
Compton, CA, 90220, USA
Tel: 310-898-1100
Fax: 310-898-1111
Belkin Ltd.
Express Business Park, Shipton Way
Rushden, NN10 6GL, United Kingdom
Tel: +44 (0) 1933 35 2000
Fax: +44 (0) 1933 31 2000
Belkin B.V.
Boeing Avenue 333
1119 PH Schiphol-Rijk, The Netherlands
Tel: +31 (0) 20 654 7300
Fax: +31 (0) 20 654 7349
Belkin Ltd.
7 Bowen Crescent, West Gosford
NSW 2250, Australia
Tel: +61 (0) 2 4372 8600
Fax: +61 (0) 2 4372 8603
© 2005 Belkin Corporation. All rights reserved. All trade names are
registered trademarks of respective manufacturers listed.
P74699-A
Download PDF