MOUNTING INSTRUCTION
WINCH 16, VER.1.1
1.
2.
3.
Remove circlip (1), using a small sharp screw driver.
Remove drum (2).
Mark location of the bolt holes using the winch base (12) as a template.
Remove the winch base. Be sure that no dust comes into contact with
the winch while drilling the bolt holes.
Drill the bolt holes ø6.5mm.
Clean the area.
Apply a light coat of bedding compound, ensuring that each hole is
bedded. Drain grooves should be kept clear.
Fasten the winch into place using 5 pcs. countersunk head screws.
Reassemble in reverse order.
Check that the winch is functioning correctly.
4.
5.
6.
7.
8.
9.
10.
WARRANTY
Refer to our website www.ronstan.com/warranty
for our warranty terms and conditions
SERVICE INSTRUCTION
WINCH 16, VER.1.1
Maintenance interval 1-2 years, depending on operation conditions.
1.
2.
3.
4.
5.
6.
7.
8.
Remove circlip (1).
Remove drum (2).
Remove the black plastic circlip (10).
Remove the drive shaft (6).
Remove the roller bearings (9,11).
Remove gear shaft (13), using a standard screwdriver.
Remove gear wheel (14).
Clean all moving parts with benzine. Please note. Direct acces to the
ratchet gear (15) requires the winch base (12) to be removed from the
deck surface, in order to release the base bottom cap (16).
Check pawls & springs for wear and replace if necessary. In order to
replace the upper pawls (4) or springs (5), the gliding washer (3)
must be removed.
Reassemble the winch in reverse order, lightly greasing all moving
parts, with a soft, small brush. We strongly recommend to use only
ANDERSEN Winch Grease for this purpose*
Check that the winch is functioning correctly.
9.
10.
11.
*) Most types of grease, including “marine grease” are NOT suitable for lubrication of winches. None suitable grease can cause mechanical malfunction. Malfunctioning pawls may lead
to unexpected failure of a loaded winch, resulting in material damage or fatal personal injury.
Service Kit No. 4 (part no. 710004) contains service parts for this winch.
PARTS LIST
WINCH 16, VER.1.1
EXPLODED VIEW
WINCH 16, VER.1.1
1
POS
QTY
DESCRIPTION
PART NO.
1
1
CIRCLIP
712800
2
2
1
DRUM
715200
3
3
1
GLIDING WASHER
718400
4
2
PAWL
713200
5
2
PAWL SPRING
713300
6
1
DRIVE SHAFT, COMPLETE
715500
7
2
PAWL SPRING
713300
8
2
PAWL
713200
9
1
ROLLER BEARING
712905
10
1
CIRCLIP
716001
11
1
ROLLER BEARING
712905
12
1
WINCH BASE
730100
13
1
GEAR SHAFT
715700
14
1
GEAR WHEEL
715400
15
1
RATCHET GEAR
711701
16
1
BASE BOTTOM CAP
715800
4
5
6
7
8
9
10
11
12
13
14
15
16
ALL WINCHES
Read All Safety Notices and Product Manuals
Do not install or operate this winch before reading and fully understanding
the contents of this Safety Notice Sheet and the Product Manual.
WORLD WIDE DISTRIBUTION & SERVICE
(FOR UPDATED DISTRIBUTOR LIST, PLEASE SEE
WWW.ANDERSENWINCHES.COM)
Stay Alert When Operating
Andersen winches are very powerful and have the potential to cause significant damage and/or serious injury if used improperly or without due caution and vigilance.
Operators Must Be Trained
Help prevent significant damage and/or serious injury by ensuring any person operating
a winch has a thorough understanding of its proper operation and is aware of the
potential hazards involved. As a minimum, all winch operators must read and understand this Safety Notice Sheet and the Product Manual.
Particular attention is drawn to the following ponts:
Children and others not qualified to operate an electric winch must be kept at a safe
distance from the winch and any rigging or fittings that are under load.
Long hair and/or loose clothing must be tied back to avoid being caught in the winch.
In the event of a rope override or other fault, stop the winch and turn off power before
attempting to resolve the problem.
Avoid Accidental Operation
Remove winch handles and turn off power to the winch when not in use to help avoid
unsupervised or unintentional operation. Failure to do so could result in significant
damage and/or serious injury.
Maintenance
Turn off power to the winch before performing any maintenance or service tasks. Failure
to do so could result in significant damage and/or serious injury.
Lifting Operations
The winch must not be operated with the rope in the self tailer when used in any kind
of lifting operation.
Any lifting operations should be conducted by two persons in order to maintain constant visual contact with the object being lifted.
Furthermore the selftailer must not be used as a cleat for a rope used to lift or suspend
any object. The rope must be secured properly by tying off, or leading to a suitable
fitting such as a cleat or bollard.
Failure to observe these precautions could result in serious injury
or death.
DO NOT DISCARD
Part nr. 710216, 9. februar 2012
Manual
WINCH 16
ver. 1.1
Manufactured by Ronstan Denmark ApS - 7100 Vejle - DENMARK
">
