Cutters Edge | Guard Depth Gauge Series | Guard Depth Gauge

Guard Depth Gauge
Safety • Speed • Control
D-6 and D-8 Guard Depth Gauge®
New Tool-Less Design
THE GUARD DEPTH GAUGE CONTROLS THE DEPTH OF CUT
• Eliminates the danger of cutting through rafters.
• Eliminates the need to “feel” for and “roll” rafters.
• Speeds ventilation cuts… Gets you off the roof faster.
• New tool-less design allows removal, adjustment or
installation in seconds.
• Large depth of cut scale… Infinite adjustment from 0” to 8”
deep.
• Large adjusting knob for fast adjustments with gloves on.
• Can be removed in seconds for conventional chain saw
applications.
• Will retrofit all Cutters Edge Saws.
GET THE EDGE
THE GUARD DEPTH GAUGE COVERS
THE ENTIRE CUTTING CHAIN
Chain & Circular Saws — 221
All specifications are subject to change without notice.
Fire Rescue Saw Specifications
Model CE-2165-RS
ENGINE
TYPE: Single-cylinder 2-cycle, with loop
scavenging
DISPLACEMENT: 4.0 cu. in. (65.1 cc)
BORE: 1.89 in. (48 mm)
STROKE: 1.4 in. (36 mm)
COMPRESSION RATIO: 9.4:1 (±0.3)
BEARINGS: Heavy-duty deep-groove ball
bearings on crankshaft, needle cage
bearings on connecting rod, piston pin
and clutch.
CYLINDER/PISTON: Open ported, single
ring design with four transfer ports.
CYLINDER MATERIAL: Nikasil
MAX ENGINE SPEED: No load…
12,500 RPM
IGNITION SYSTEM
TYPE: Electronic, one piece modular, CD
BRAND: FHP
SPARK PLUG: Champion CJ7Y or
equivalent
GAP: 0.020 in. (0.5 mm)
STARTING SYSTEM
ONE STEP STARTING SYSTEM WITH
COMPRESSION RELEASE
Comprised Of…
Momentary contact switch
Combined choke/throttle lock with
throttle safety guard.
AIR FILTRATION
SYSTEM: “RAM-AIR” with metered stack
TYPE: 4-stage, oil tack barrier, external
mount
SURFACE AREA: 211.4 Square Inches
MICRON RATING: < 1 micron
FUEL & ENGINE LUBRICATION
GASOLINE OCTANE RATING: Use
87 octane or higher.
FUEL MIX OIL/RATIO: With Cutters Edge
Synthetic Oil: …100:1
If petroleum base 2-cycle oil used: …50:1
FUEL TANK CAPACITY: 26.8 fl. oz.
(0.77 liters)
CARBURETOR ISOLATION
Designed to eliminate Vapor-lock and
vibration
TYPE: Air gap isolation and Bakeolite
insulation Pressurized carburetor
compartment keeps out dirt.
DRIVE SYSTEM
TYPE: Inboard, 3-shoe centrifugal clutch
STYLE: Rim & Drum System
Radially Ported to keep rim free of tar &
debris build-up… free floating to keep
chain in perfect alignment with bar
groove.
SIZE: .404 by 7 tooth
CHAIN SPEED: No Load chain speed
98.5 FPS (feet per second)
GUIDE BAR
TYPE: Solid one piece construction,
No Rivets/No Laminates… 20” and 16”
slotted for Guard/Depth Gauge.
MATERIAL
TITANIUM ALLOY, 7 mm thick;
STYLE: Roller Blade/Speed Ring with
sealed bearing.
CUTTING LENGTHS: 20”, 16” and 12”
SIZE: .404 Pitch .063 Gauge
Model CE-2171-RS
CUTING CHAIN
CUTTERS EDGE BULLET® Chain
TYPE: Carbide Tipped BULLET® Chain
SIZE: .404 pitch .063 Gauge
CUTTING CHAIN LUBRICATION SYSTEM
TYPE: Fully automatic, adjustable
DRIVE SYSTEM: Geared to Centrifugal
Clutch
LUBRICANT: Cutters Edge “High Tack”
Bar & Chain Oil or high quality bar &
chain oil.
OIL TANK CAPACITY: 14.24 fl. oz.
(0.42 liters)
HANDLES
TYPE: Front/Top… Full Wrap (For ease of
use with gloves, from either side of saw)
Back… Flared base for kickback guard
Full isolation anti-vibration.
VIBRATION LEVELS
* FRONT HANDLE M/S2 :3, 6
* REAR HANDLE M/S2 :5, 7
(* see Note 2)
SILENCING
MUFFLER: Oversize, top ported, low
restriction with fire screen.
** NOISE LEVEL: 102dB(A) at maximum
output.
(** see Note 1)
GUARD/DEFLECTOR
TYPE: Aluminum front mount to cover
muffler and control air-flow for delivery of
cleaner, cooler air to cylinder heat
exchangers…
(Keeps engine running cooler and
reduces maintenance)
CHAIN BRAKE
TYPE: Inertia Activated
STYLE: Free-Swinging Pendulum
BREAKING TIME: < 0.20 second
GUARD/DEPTH GAUGE® (Optional)
(No tools needed for installation,
adjustments or removal.)
FUNCTION: Covers all the cutting chain,
allows saw operator to set depth of cut to
avoid cutting structural members.
MATERIAL: Anodized aluminum
TYPE: D6 for 16” saw… D8 for 20” saw
3-point mount, positive lock with depth of
cut scale.
DEPTH OF CUT: D6 = 6” D8 = 8”
WEIGHT
POWERHEAD ONLY: 13.9 lbs. (Dry Weight)
CE-2165RS-12”:
21.0 lbs.
CE-2165RS-16”:
21.5 lbs.
CE-2165RS-20”:
22.0 lbs.
CE-2165RS/D6:
24.0 lbs.
CE-2165RS/D8:
24.5 lbs.
STANDARD ACCESSORIES
ACCESSORIES INCLUDED WITH ALL FIRE
RESCUE SAWS
“Scrench” holder and “Scrench” tool,
complete tool kit including grease gun
and packet of grease, complete manuals,
filter oil, Cutters Edge 2-cycle oil mix,
Cutters Edge bar & chain oil, bar
scabbard (saws without D6 and D8 only)
INCLUDED WITH D6 & D8 SAWS ONLY…
Training video for Guard/Depth Gauge
assembly, operation and maintenance.
ENGINE
TYPE: Single-cylinder 2-cycle, with loop
scavenging
DISPLACEMENT: 4.3 cu. in. (70.7 cc)
BORE: 1.97 in. (50 mm)
STROKE: 1.4 in. (36 mm)
COMPRESSION RATIO: 10.2:1 (±0.3)
BEARINGS: Heavy-duty deep-groove ball
bearings on crankshaft, needle cage
bearings on connecting rod, piston pin
and clutch.
CYLINDER/PISTON: Closed ported, dual
ring design with four transfer ports.
CYLINDER MATERIAL: Nikasil
MAX ENGINE SPEED: No load…
13,500 RPM
IGNITION SYSTEM
TYPE: Electronic, one piece modular, CD
BRAND: FHP
SPARK PLUG: Champion CJ7Y or
equivalent
GAP: 0.020 in. (0.5 mm)
STARTING SYSTEM
ONE STEP STARTING SYSTEM WITH
COMPRESSION RELEASE
Comprised Of…
Momentary contact switch
Combined choke/throttle lock with
throttle safety guard.
AIR FILTRATION
SYSTEM: “RAM-AIR” with metered stack
TYPE: 4-stage, oil tack barrier, external
mount
SURFACE AREA: 211.4 Square Inches
MICRON RATING: < 1 micron
FUEL & ENGINE LUBRICATION
GASOLINE OCTANE RATING: Use
87 octane or higher.
FUEL MIX OIL/RATIO: With Cutters Edge
Synthetic Oil: …100:1
If petroleum base 2-cycle oil used: …50:1
FUEL TANK CAPACITY: 26.8 fl. oz.
(0.77 liters)
CARBURETOR ISOLATION
Designed to eliminate Vapor-lock
TYPE: Air gap isolation and Bakeolite
insulation Pressurized carburetor
compartment keeps out dirt.
DRIVE SYSTEM
TYPE: Inboard, 3-shoe centrifugal clutch
STYLE: Rim & Drum System
Radially Ported to keep rim free of tar &
debris build-up… free floating to keep
chain in perfect alignment with bar
groove.
SIZE: .404 by 8 tooth
CHAIN SPEED: No Load chain speed
121.6 FPS (feet per second)
GUIDE BAR
TYPE: Solid one piece construction,
No Rivets/No Laminates… 20” and 16”
slotted for Guard/Depth Gauge.
MATERIAL
TITANIUM ALLOY, 7 mm thick;
STYLE: Roller Blade/Speed Ring with
sealed bearing.
CUTTING LENGTHS: 20”, 16” and 12”
SIZE: .404 Pitch .063 Gauge
CUTING CHAIN
CUTTERS EDGE BULLET® Chain
TYPE: Carbide Tipped BULLET® Chain
SIZE: .404 pitch .063 Gauge
CUTTING CHAIN LUBRICATION SYSTEM
TYPE: Fully automatic, adjustable
DRIVE SYSTEM: Geared to Centrifugal
Clutch
LUBRICANT: Cutters Edge “High Tack”
Bar & Chain Oil or high quality bar &
chain oil.
OIL TANK CAPACITY: 14.24 fl. oz.
(0.42 liters)
HANDLES
TYPE: Front/Top… Full Wrap (For ease of
use with gloves, from either side of saw)
Back… Flared base for kickback guard
Full isolation anti-vibration.
VIBRATION LEVELS
* FRONT HANDLE M/S2 :4, 6
* REAR HANDLE M/S2 :5, 2
(* see Note 2)
SILENCING
MUFFLER: Oversize, top ported, low
restriction with fire screen.
** NOISE LEVEL: 104dB(A) at maximum
output.
(** see Note 1)
GUARD/DEFLECTOR
TYPE: Aluminum front mount to cover
muffler and control air-flow for delivery of
cleaner, cooler air to cylinder heat
exchangers…
(Keeps engine running cooler and
reduces maintenance)
CHAIN BRAKE
TYPE: Inertia Activated
STYLE: Free-Swinging Pendulum
BREAKING TIME: < 0.20 second
GUARD/DEPTH GAUGE® (Optional)
(No tools needed for installation,
adjustments or removal.)
FUNCTION: Covers all the cutting chain,
allows saw operator to set depth of cut to
avoid cutting structural members.
MATERIAL: Anodized aluminum
TYPE: D6 for 16” saw… D8 for 20” saw
3-point mount, positive lock with depth of
cut scale.
DEPTH OF CUT: D6 = 6” D8 = 8”
WEIGHT
POWERHEAD ONLY: 13.9 lbs. (Dry Weight)
CE-2171RS-12”:
21.0 lbs.
CE-2171RS-16”:
21.5 lbs.
CE-2171RS-20”:
22.0 lbs.
CE-2171RS/D6:
24.0 lbs.
CE-2171RS/D8:
24.5 lbs.
STANDARD ACCESSORIES
ACCESSORIES INCLUDED WITH ALL FIRE
RESCUE SAWS
“Scrench” holder and “Scrench” tool,
complete tool kit including grease gun
and packet of grease, complete manuals,
filter oil, Cutters Edge 2-cycle oil mix,
Cutters Edge bar & chain oil, bar
scabbard (saws without D6 or D8 only)
INCLUDED WITH D6 & D8 SAWS ONLY…
Training video for Guard/Depth Gauge
assembly, operation and maintenance.
Specifications are subject to change without notice
**Note 1: Equivalent noise level is, according to ISO 7182 and ISO 9207 calculated as the time-weighted energy total for noise levels under various working conditions with the
following time distribution: 1/3 idle, 1/3 full load, 1/3 full speed.
**Note 2: Equivalent vibration level is, according to ISO 7505 calculated as the time-weighted energy total for vibration levels under various working conditions with the following
time distribution: 1/3 idle, 1/3 full load, 1/3 full speed.
Cutters Edge, D8 Guard/Depth Gauge® and BULLET® Chain are registered trademarks of Edge Industries Inc. Pat 5,056,395 5,156,156 P.O. Box 1179, Julian CA 92036 USA
Chain & Circular Saws — 222
All specifications are subject to change without notice.
BULLET® Chain
Fire Department Style Carbide Tipped Chain
The Safest Chain Made Today…Virtually Eliminates Kickback.
The first and only chain designed from the ground up for fire
department ventilation, forcible entry, and rescue operations.
The BULLET® Chain’s patented cutter is a solid piece of
metal without bends or ground out areas that cause weak
points. The carbide insert is formulated specifically for fire
department use and uses a unique patented “locking key” to
mount it to the cutter body.
The raker gauge is shaped like the nose of a bullet to protect
the carbide insert from impact and the gullet is very narrow
to stop any “hooking”, while also reducing impact.
Rathan “cutting”, the BULLET® Chain actually “files”.
Because the cutting edge is exposed around the entire
circumference of the cutter, material is removed remarkably
fast.
PATENT NUMBER
5,056,395
The BULLET® cutter is .068” thick (sixty eight thousands)…
that’s up to .18” (eighteen thousands) thicker than other
chains! For even more strength, the drive links are also .068”
thick (sixty eight thousands) at the rivet holes, then “coined”
down to .063” to fit into the groove of our guide bar and many
standard guide bars. Extremely tough tempered rivets with
.068” hubs are used to hold it all together and reduce
stretching.
The sesult is a fast cutting, extremely durable fire service
carbide chain. Extensive in service use shows tghe BULLET®
Chain outlasting standard carbide chain up to 20 times!
DRIVE LIINK
TOP .068”
DRIVE LIINK
BOTTOM
”COINED” DOWN
TO .063”
RIVET HEAD
And of course, when the BULLET® Chain gets dull or cutters
are broken it can be repaired and sharpened quickly and
inexpensively by Edge Industries or your local Cutters Edge
dealer.
TOP VIEW
RAKER GAUGE
PROTECTS
ENTIRE
CARBIDE
LOCKING
KEY
THIN RAKER
GAUGE PROTECTS
ONLY A SMALL
PORTION OF
THE CARBIDE
LARGE OPEN
GULLET CAUSES
”HOOKING” OF
NAILS
BACK VIEW
NARROW GULLET
STOPS ”HOOKING”
BULLET
CUTTER
SOLID BODY
LARGE SOLDER
AREA
THIN BODY
AND BENT
AREA BREAK
EASILY
VERY SMALL
SOLDER AREA
STANDARD
CARBIDE
CUTTER
Chain & Circular Saws — 223
All specifications are subject to change without notice.
Universal Guard/Depth Gauge®
Added Safety and Ease of Use for Most
Chain Saws
I you use a chain saw for cutting ventilation, forcible entry, or
rescue… the Universal Guard/Depth Gague® will enhance
safety and increase the ease and speed of your cutting!
Designed after the Cutters Edge D8 Guard/Depth Gauge® the
universal design fits almost all sizes and brands of chain saw.
When used with a 16” (or smaller) Guide Bar the Universal
Guard/Depth Gauge® will cover all the cutting chain. If used
on guide bars longer than 16”, only the portion of chain
between the engine and back edge of the guard will be
exposed.
The Universal Guard/Depth Gauge® is easy to mount to
almost any chain saw. Instructions, cobalt drill bits, and allen
wrench are included. Drill two holes, screw in one screw,
and you are ready to cut.
• Only one moving part.
• Large adjusting knob for fast adjustments with gloves on.
• Large depth of cut scale with infinite adjustment from 0” to
6” deep.
• Can be removed in minutes… for conventional chain saw
applications.
• Operator is protected from contact with the chain.
• Reduces the danger of kickback.
• Allows for extended reach.
• Provides for greater control.
• Speeds ventilation cuts.
• Eliminates the danger of cutting through rafters.
• Gets you off the roof faster.
Cutters Edge® BULLET CHAIN® and Titanium Guide Bars are
available to fit many chain saws (over 3.5 cu. in.).
Contact Cutters Edge or your local Cutters Edge Dealer for a
quote.
Chain & Circular Saws — 224
All specifications are subject to change without notice.
GET THE EDGE
QuikventTM Ventilation Saws
QV-670 / QV-675
QV-8000 / QV-8050
THE PREFERRED CHOICE AMONG
FIRE/RESCUE PERSONNEL FOR
VENTILATING BUILDING
STRUCTURES.
THIS PROFESSIONAL
VENTILATION SAW
INCORPORATES MANY OF THE
SAME FEATURES AS THE QV670/675, PLUS THE FOLLOWING:
• Patented droop nose bar with
Carbide chain provides optimum
angle for cutting through wood and asphalt shingles.
• Unique patented skid plate allows operator to pivot the bar nose
into a structure.
• Extra large, easy-grip starter handle.
• External idle control adjustment.
• Heavy-duty cartridge-type air filter.
• Side access chain tensioner.
Bonus - QV-675 includes steel carrying case, 1 gal. QV bar and chain oil and
1 gal. safety gas can.
• Echo’s largest chain saw power
head 80.7 cc.
• Superb power-to-weight ratio, lighter than most other saws in its
class.
Bonus - QV-8050 includes steel carrying case, 1 gal. QV bar and chain oil and
1 gal. safety gas can.
Echo offers a full line of accessories to
complement your chain saw or
QuikVentTM. All with the same quality
and workmanship you expect from
Echo.
CHAIN SAW/QUIKVENTTM ACCESSORIES
CHAIN SAW BARS AND CHAINS
CHAIN SAW ACCESSORIES
CHAIN SAW
MODEL
BAR
LENGTH
BAR ITEM
NUMBER
CHAIN ITEM
NUMBER
ECS-2000
ECS-3000
CS-300/340/345
(IntenzTM)
12”
16”
12”
120374001
160375001
120374501
(122374501)
140375201
(142375201)
160375701
(162375701)
160336601
180337201
200337801
160386001
200387001
240388101
270389301
200387001
240388101
270389301
320380501
360381601
917045
917056
917045
14”
16”
CS-4400/5000/
510
16”
18”
20”
16”
20”
24”
27”
20”
24”
27”
32”
36”
CS-6700/670
CS-8000
ITEM NUMBER
DESCRIPTION
999440-00020
999888-00207
Felling Wedge
Removable Nose Case for CS-280E, 330EVL, 300, 340, 345,
ECS-2000, ECS-3000
Fixed Nose Case for CS-3900, 4400, 4600, 5000, 510, 6700,
670 (20” bar)
17” Bar & Chain Scabbard
20” Bar & Chain Scabbard
999888-01205
917052
898503-08032
898503-08033
917056
KICK GUARDS
333066
333072
333078
727060
727070
727081
727093
727070
727081
727093
7270105
7270116
ITEM NUMBER
CHAIN SAW MODEL
99988800016
2894901
2893201
ECS-2000/3000
CS-300/340-345
CS-4400/5000/510/6700/670/8000
QUIKVENTTM ACCESSORIES
ITEM NUMBER
DESCRIPTION
999888-00045
999888-00050
999888-00141
999447-00190
999888-01011
999888-01140
QuikVentTM Carbide Chain Loop
QuikVentTM Bar & Chain Oil
QuikVentTM Bar
QuikVentTM Storage Case
One Gallon Safety Gas Can
QuikVentTM Scabbard
MODEL
ENGINE
DISPLACEMENT
(cc.)
CARBERETOR
PRO-FIRE®
ELECTRONIC
IGNITION
ENGINE
TYPE
OILING
SYSTEM
CHAIN
BRAKE
STD BAR
LENGTH
(in.)
FUEL
CAPACITY
(ft. oz.)
OIL
CAPACITY
(fl. oz.)
VIBRATION
REDUCTION
SYSTEM
DRY
WARRANTY
WEIGHT*
(lbs.)
QV-670
66.7
Diaphragm
STD
Air Cooled
Two-Stroke
STD
12
21
10.5
STD
15.2
QV-675
66.7
Diaphragm
STD
Air Cooled
Two-Stroke
STD
12
21
10.5
STD
15.2
QV-8000
80.7
Diaphragm
STD
Air Cooled
Two-Stroke
STD
12
27.7
13.5
STD
18.3
QV-8050
80.7
Diaphragm
STD
Air Cooled
Two-Stroke
Auto &
Manual
Override
Auto &
Manual
Override
Auto &
Manual
Overide
Auto &
Manual
Overide
STD
12
27.7
13.5
STD
18.3
2 yr. con.
1 yr. com.
90 day ren.
2 yr. con.
1 yr. com.
90 day ren.
2 yr. con.
1 yr. com.
90 day ren.
2 yr. con.
1 yr. com.
90 day ren.
* Without bar and chain.
Chain & Circular Saws — 225
All specifications are subject to change without notice.
Super Blade
Edge Carbide Chip Blade
The most effective, efficient, versatile and longest lasting
rescue saw blade available.
Rescue personal report that the WHITE EDGE SUPER BLADE
lasts 10 to 20 times longer than standard carbide tipped
blades and cuts many materials that abrasive wheels and
diamond blades cannot. The SUPER BLADE cuts FASTER and
CLEANER than any other blade you have ever used, resulting
in faster ventilation/rescues and leading to more lives saved.
SUPER BLADE represents leading edge technology in
carbide blade development.
The WHITE EDGE carbide “chip” design exposes over 300
cutting chips that rapidly saw through almost anything it has
to. These remarkable blades come in 12“, 14” and 16”
diameters and fit all brands of circular blade rescue saws
with 1”, 7/8” and 20 mm arbors.
CUTS FAST AND CLEAN THROUGH…
• Insulation materials
• Tar & gravel roofs
• Metal studs
• Shingle roofs
• Corrugated roofing
• Hardwood floors
• Auto body parts
• Sheet metal, tin
• Paperboards
• Countertops
• Cardboards
• Drywall
• Woods
• Press wood
• Aluminum
• Tree roots
• Hard boards
• Pallets
• Tires
• Decking
• Timber
• Rail ties
• Plastic
WARNING: Certain manufactures prohibit using carbide
blades of any type on their saws. When purchasing new
rescue saws or carbide blades for existing equipment
make sure you secure manufactures authorization to use
this product.
IMPORTANT: The SUPER BLADE will cut a multitude of
materials. However, it is NOT designed to cut through CONCRETE or STEEL. Continue to use abrasive wheels and diamond blades to cut these materials.
Chain & Circular Saws — 226
All specifications are subject to change without notice.
“Turbo Cut System!
Smooth and Powerful
Two words that perfectly describe Eskimo’s Barracuda ice
auger.
Our TURBO cut system delivers smooth cutting in all ice
conditions, even through old holes!
You’ll love the look of our featured Purple and Silver powder
coat finish!
Unbelievable quality in a mid-price auger!
“A GREAT NEW AUGER FROM ESKIMO!”
MADE IN USA
2-HP ESKIMO 8900 BARRACUDA
BARRACUDA ICE AUGERS BY ESKIMO
STOCK NO.
DESCRIPTION
8900B6
8900B8
8900B10
9000B8
9000B10
2-hp Barracuda 8900 w/6” Auger
2-hp Barracuda 8900 w/8” Auger
2-hp Barracuda 8900 2/10” Auger
3-hp Barracuda Plus 9000 w/8” Auger
3-hp Barracuda Plus 9000 w/10“ Auger
All specifications are subject to change
Chain & Circular Saws — 227
All specifications are subject to change without notice.
Download PDF