Paradox EVO 48, EVO 192 security and access system Programming Guide

Paradox EVO 48, EVO 192 security and access system Programming Guide

Below you will find brief information for Security and Access System EVO 48, Security and Access System EVO 192. This document will guide you through programming your Paradox EVO48 or EVO192 control panel. It covers everything from setting up zones and keyswitches to configuring programmable outputs, remote controls, and control panel settings. You'll learn how to assign doors to the system, create schedules, and manage access levels. This guide will also help you understand the different report codes and troubleshooting tips.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Paradox EVO EVO48, EVO EVO192 Programming Guide | Manualzz
Digiplex EVO High Security and Access System
EVO48 V2.1
EVO192 V2.1
Programming Guide
Warranty
For complete warranty information on this product please refer to the Limited Warranty Statement found on our Web site: www.paradox.com. Your use of this Paradox product signifies
your acceptance of all warranty terms and conditions.
© 2002-2010 Paradox Security Systems Ltd. All rights reserved. Specifications may change without prior notice. One or more of the following US patents may apply: 7046142, 6215399,
6111256, 6104319, 5920259, 5886632, 5721542, 5287111, 5119069, 5077549 and RE39406 and other pending patents may apply. Canadian and international patents may also apply.
Digiplex, Digiplex EVO, Magellan, PosiPIN and WinLoad are trademarks or registered trademarks of Paradox Security Systems Ltd. or its affiliates in Canada, the United States and/or other
countries. For the latest information on products approvals, such as UL and CE, please visit www.paradox.com.
Limitations of Alarm Systems
It must be understood that while your Paradox alarm system is highly advanced and secure, it does not offer any guaranteed protection against burglary, fire or other emergency (fire and
emergency options are only available on certain Paradox models). This is due to a number of reasons, including by not limited to inadequate or improper installation/positioning, sensor
limitations, battery performance, wireless signal interruption, inadequate maintenance or the potential for the system or telephone lines to be compromised or circumvented. As a result,
Paradox does not represent that the alarm system will prevent personal injury or property damage, or in all cases provide adequate warning or protection.
Your security system should therefore be considered as one of many tools available to reduce risk and/or damage of burglary, fire or other emergencies, such other tools include but are
not limited to insurance coverage, fire prevention and extinguish devices, and sprinkler systems.
We also strongly recommend that you regularly maintain your security systems and stay aware of new and improved Paradox products and developments.
Warning for Connections to Non-Traditional Telephony (e.g., VoIP)
Paradox alarm equipment was designed to work effectively around traditional telephone systems. For those customers who are using a Paradox alarm panel connected to a nontraditional telephone system, such as Voice Over Internet Protocol (VoIP) that converts the voice signal from your telephone to a digital signal traveling over the Internet, you should be
aware that your alarm system may not function as effectively as with traditional telephone systems.
For example, if your VoIP equipment has no battery back-up, during a power failure your system's ability to transmit signals to the central station may be compromised. Or, if your VoIP
connection becomes disabled, your telephone line monitoring feature may also be compromised. Other concerns would include, without limitation, Internet connection failures which
may be more frequent than regular telephone line outages.
We therefore strongly recommend that you discuss these and other limitations involved with operating an alarm system on a VoIP or other non-traditional telephone system with your
installation company. They should be able to offer or recommend measures to reduce the risks involved and give you a better understanding.
Things You Need to Know
About this Programming Guide
Use this programming guide to record programmed settings for your Digiplex EVO control panel. This guide should be used along
with the Digiplex EVO Reference and Installation Manual (available online only) whenever installing or programming your Digiplex
EVO system.
Conventions
The following typographical conventions are used throughout this guide:
Section numbers appear in bold typeface, enclosed by brackets: e.g., Enter a section
number between [0501]...
WARNING: Important information
Keypad keys and control panel labels appear in small caps, bold typeface: e.g., Press
0, and then ENTER to clear a zone’s serial number...
NOTE: Suggestion or reminder
Default Settings: Values which appear in bold typeface and/or are preceded by the symbol , signify the default value:
e.g., User code length:  6 digits  4 digits (4 digits is the default value)
Installer Code
The default installer code is 000000. This code allows you to enter programming mode, where you can program all features,
options, and commands of your EVO control panel. To change the installer code, see Installer Code Programming on page 28.
System Master Code
The default system master code is 1234 or 123456. This code allows you to utilize any arming method, as well as program user
codes. This code can be either four or six digits long.
Panel Reset
Performing a panel reset will reset all panel settings to their preset, default values, or custom settings (if already programmed). To
perform a panel reset, press and hold the panel’s RESET and AUX buttons for four seconds, or refer to Software Reset on page 54.
Entering Programming Mode
To enter programming mode, proceed as follows:
1. Press and hold the 0 key.
2. Enter your installer code (default is 000000). See Installer Code for details.
3. Enter the four-digit section you wish to program.
4. Enter the required data and record your settings using the worksheets included in this guide.
Decimal and Hexadecimal Programming Table
Certain sections may require the entry of one or more hexadecimal values from 0 to F.
K641/K641R Keypads
Table 1: Decimal and hexadecimal values using the K641 or K641R keypads
Key
0 to 9
Value or Action
0 to 9 (hex and decimal)
STAY
A (hex only)
FORCE
B (hex only)
ARM
C (hex only)
DISARM
D (hex only)
BYP
E (hex only)
MEM
F (hex only)
CLEAR
Exit section without saving (hex and decimal)
ENTER
Save current data and advance to next section (hex only)
Version 2.1
Things You Need to Know | 3
K656 Keypad
Table 2: Decimal and hexadecimal values using the k656 keypad
Value or Action
Key
0 to 9
0 to 9 (hex and decimal)
ARM
A (hex only)
SLEEP
B (hex only)
STAY
C (hex only)
OFF
D (hex only)
MENU
E (hex only)
F (hex only)
CLEAR
Exit section without saving (hex and decimal)
ENTER
Save current data and advance to next section (hex only)
Grafica Keypads
Table 3: Decimal and hexadecimal values using Grafica keypads
Key
0 to 9
#
Right action key (Exit)
Central action key (Save)
4 | Things You Need to Know
Value or Action
values 0 to 9 respectively
A to F (press the # key until the desired letter appears)
Exit section without saving
Save current data and advance to next section
Version 2.1
Contents
Serial Number List .................................................... 7
Zone Programming ................................................ 10
Keyswitch Programming ....................................... 17
Keyswitch Numbering ............................................................................17
Keyswitch Parameters ............................................................................17
Keyswitch Arming/Disarming Report Codes ....................................17
Programmable Outputs ........................................ 19
PGM Test Mode ........................................................................................19
PGM Delays ...............................................................................................19
PGM Options ............................................................................................19
PGM Programming .................................................................................19
Event and Feature Groups ....................................................................20
Utility Keys .................................................................................................27
Input Speeds .............................................................................................28
Installer Code Programming ................................................................28
User Code Options ................................................. 28
Arming and Disarming Report Codes .................. 29
Access Control Sections ......................................... 30
Assigning Doors to the System ............................................................30
Schedule Programming .........................................................................31
Backup Schedules ...................................................................................32
Access Levels .............................................................................................33
Holidays .....................................................................................................33
Keypad Numbering ................................................ 33
Remote Control Programming ............................. 34
Remote Control Templates ...................................................................34
Control Panel Settings ........................................... 36
System Options ...................................................... 36
Dialer Options ........................................................ 38
Additional Options ................................................ 39
Schedule Tolerance Window ................................................................39
AutoTest Report Settings .......................................................................39
Timings ......................................................................................................39
Communication Settings ....................................... 39
Account Numbers ...................................................................................39
Reporting Formats ..................................................................................40
System Event Call Direction .................................. 41
Partition Settings ...................................................45
Auto-arm Times .......................................................................................45
Arming/Disarming Report Schedules ................................................45
Partition Timers .......................................................................................46
Partition Options 1 .................................................................................47
Partition Arming/Disarming Options ................................................48
Partition Panic Alarm Options .............................................................48
Partition Bell Squawk Options .............................................................48
Partition One-touch Options ................................................................49
Partition Special Options ......................................................................49
Partition Arming/Disarming Event Call Direction ..........................49
Partition Alarm/Alarm Restore Event Call Direction ......................50
Partition Tamper/Tamper Restore Event Call Direction ................50
Special Arming Exit Delay .....................................................................50
No Movement Schedule ........................................................................51
Special and Trouble Report Codes ........................51
Special Report Codes ..............................................................................51
Trouble Report Codes .............................................................................52
Additional Settings and Modes .............................52
Paradox PMC5 Memory Key .................................................................53
Automatic Report Code Programming ..............................................53
Software Reset .........................................................................................54
Installer Function Keys ...........................................................................54
Automatic Report Codes .......................................................................55
Contact ID Report Codes .......................................................................58
Keypad Programming ............................................60
K641/K641R and K656 ...........................................................................60
Label Programming ...............................................................................61
Using the Memory Key ...........................................................................62
Combus Voltmeter ..................................................................................63
Updating Firmware Using WinLoad ..................................................63
Hardware Connections for the Control Panel ......63
Milliamp Consumption ..........................................................................63
Connecting the Combus in Noisy Environments .............................64
Built-in RTC ...............................................................................................64
Trouble Display .......................................................65
K641/K641R and K648 ...........................................................................65
K656 ............................................................................................................65
Grafica .......................................................................................................65
Trouble Groups ........................................................................................65
Notes
VDMP3 Voice Module ............................................ 41
PCS GSM/GPRS Communicator Module ............... 42
WinLoad/PCS Module Connection .....................................................42
PCS Module Programming ...................................................................42
PCS Module (GSM) Programming .......................................................42
SMS Site Name .........................................................................................43
IP100/PCS Module (GPRS) Options .....................................................43
IP/GPRS Reporting Account Programming .......................................43
IP100/PCS Module Report Code Programming ...............................44
Version 2.1
Contents | 5
List of Worksheets
Worksheet 1: System Planning ............................................................................................................7
Worksheet 2: Zone Information ........................................................................................................ 11
Worksheet 3: Zone Report Codes .................................................................................................... 15
Worksheet 4: Zone Labels ................................................................................................................... 16
Worksheet 5: Keyswitch Numbering and Parameters .............................................................. 18
Worksheet 6: Arming and Disarming with Keyswitch Report Codes .................................. 18
Worksheet 7: PGM Delays ................................................................................................................... 19
Worksheet 8: PGM Programming .................................................................................................... 19
Worksheet 9: Input Speeds ................................................................................................................ 28
Worksheet 10: Installer Code Programming ................................................................................ 28
Worksheet 11: Arming and Disarming Report Codes ............................................................... 29
Worksheet 12: Assigning Doors ........................................................................................................ 30
Worksheet 13: Programming Primary Schedules ...................................................................... 31
Worksheet 14: Programming Secondary Schedules ................................................................. 32
Worksheet 15: Programming Backup Schedules ....................................................................... 32
Worksheet 16: Programming Access Levels ................................................................................ 33
Worksheet 17: Programming Holidays .......................................................................................... 33
Worksheet 18: Numbering Keypads ............................................................................................... 34
Worksheet 19: Programming Remote Controls .......................................................................... 35
Worksheet 20: Control Panel Settings ............................................................................................ 36
Worksheet 21: Schedule Tolerance Window ............................................................................... 39
Worksheet 22: AutoTest Report Settings ...................................................................................... 39
Worksheet 23: Timings Settings ....................................................................................................... 39
Worksheet 24: Account Number Settings ..................................................................................... 40
Worksheet 25: Reporting Formats for Section [3070] .............................................................. 40
Worksheet 26: Reporting Formats for Sections [3071] to [3074] .......................................... 40
Worksheet 27: VDMP3 Settings ........................................................................................................ 41
Worksheet 28: VDMP3 functions for Sections [3091] to [3098] ............................................ 41
Worksheet 29: WinLoad/PCS Module Connection Settings ................................................... 42
Worksheet 30: PCS Module (GSM) Settings .................................................................................. 42
Worksheet 31: SMS Site Name Settings ......................................................................................... 43
Worksheet 32: IP Account Number Settings ................................................................................ 43
Worksheet 33: IP Receiver 1 Configuration .................................................................................. 43
Worksheet 34: IP Receiver 2 Configuration .................................................................................. 44
Worksheet 35: IP Receiver 3 Configuration .................................................................................. 44
Worksheet 36: IP Receiver 4 Configuration .................................................................................. 44
Worksheet 37: PCS Module Report Codes .................................................................................... 44
Worksheet 38: IP100 Report Codes ................................................................................................. 44
Worksheet 39: Partition Label Settings for Sections [3100] to [3800] ................................. 45
Worksheet 40: Auto-arm Time Settings ......................................................................................... 45
Worksheet 41: Arming Report Schedule Settings ...................................................................... 45
Worksheet 42: Disarming Report Schedule Settings ................................................................ 46
Worksheet 43: Partition Timer Settings ......................................................................................... 46
Worksheet 44: Special Arming Exit Delay Settings .................................................................... 50
Worksheet 45: No Movement Schedule Settings ....................................................................... 51
Worksheet 46: Special Report Code Settings .............................................................................. 51
Worksheet 47: Trouble Report Code Settings ............................................................................. 52
Worksheet 48: Keypad Settings for Sections [007] to [013] .................................................... 61
Worksheet 49: Door Unlocked Schedule (K641R only) ............................................................ 61
Worksheet 50: PGM Activation and Deactivation ...................................................................... 61
Worksheet 51: Milliamp Consumption of Various Devices ..................................................... 63
6 | List of Worksheets
Version 2.1
Digiplex EVO • Programming Guide
Serial Number List
Worksheet 1: System Planning
Serial # Sticker
Serial # Sticker
Serial # Sticker
Serial # Sticker
Serial # Sticker
Serial # Sticker
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
Version 2.1
Serial Number List | 7
Digiplex EVO • Programming Guide
Worksheet 1: System Planning (Continued)
Serial # Sticker
Serial # Sticker
Serial # Sticker
Serial # Sticker
Serial # Sticker
Serial # Sticker
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
8 | Serial Number List
Version 2.1
Digiplex EVO • Programming Guide
Worksheet 1: System Planning (Continued)
Serial # Sticker
Serial # Sticker
Serial # Sticker
Serial # Sticker
Serial # Sticker
Serial # Sticker
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
Version 2.1
Serial Number List | 9
Digiplex EVO • Programming Guide
Zone Programming
Use the following section to program all zones on your EVO48 or EVO192 control panel.
To program zones:
1.
Enter section [0400].
2.
Enter the zone number you wish to program.
NOTE: In any zone programming option, pressing ACC on the K641/K641R, or on the K656, will save the data and access the next zone on the same option screen.
Pressing TRBL on the K641/K641R, or on the K656, will save the data and return to the previous zone on the same option screen. In addition, if you’re using a
keypad other than a K641, K656, K07C, or K07 (version 2.2 and higher), use the section numbers outlined in table 8 to program zones. Without a K641, K656, or
Grafica keypad, you can only program zones 1 to 96.
3.
4.
5.
6.
7.
Enter the zone’s eight-digit serial number, then it’s three-digit input number (the input number is not needed for modules with only one input). Press 0, and
then ENTER to clear a zone’s serial number. Use worksheet 2 on page 11, to record the information.
Enter the following zone parameters; default setting is (01) (*2*4***):
a.
A zone definition, by referring to table 4
b.
A partition, by referring to table 5
c.
A zone option, by referring to table 6
Enter the zone’s report codes, by referring to table 7; default: (00) (00) (00) (00). Use worksheet 3 on page 15, to record the information.
Enter the zone’s label. Use worksheet 4 on page 16, to record the information.
Press ENTER to save and proceed to the next zone.
NOTE: Pressing CLEAR twice will exit the zone programming menus. To save your modifications, make sure to press ENTER before pressing CLEAR.
Table 4: Zone definitions for EVO48/EVO192
Table 5: Partition assignment for EVO48/EVO192
Input Value Description
Table 6: Zone options for EVO48/EVO192
Input Value Description
Input Value Description
0
Disabled (default)
1
Assign to partition 1
1
Auto zone shutdown enabled
1
Entry delay 1
2
Assign to partition 2
2
Bypass enabled (default: ON)
2
Entry delay 2
3
Assign to partition 3
3
Stay zone
3
Follow
4
Assign to partition 4
4
Force zone (default: ON)
4
Instant
5
Assign to partition 5
7
Intellizone
5
24 hr. buzzer
6
Assign to partition 6
8
Delay before transmission
6
24 hr. burglary
7
Assign to partition 7
7
24 hr. hold-up
8
Assign to partition 8
8
9
Input Value
Zone Alarm Type
5
6
24 hr. gas
OFF
OFF
24 hr. heat
OFF
ON
Pulsed alarm
A
24 hr. water
ON
OFF
Silent alarm
B
24 hr. freeze
ON
ON
Report only
C
Delayed 24 hr. fire
D
Standard 24 hr. fire
E
Stay delay 1
F
Stay delay 2
Table 7: Zone report codes for EVO48/EVO192
Steady alarm
Table 8: Section numbers used for zone programming
Alarm Report
Code
Alarm Restore
Report Code
Tamper Report
Code
Tamper Restore
Report Code
Zone
Number
Zone Serial &
Input Numbers
Zone
Parameters
Zone Report
Codes
Zone Label
__ / __
__ / __
__ / __
__ / __
1
[0001]
[0101]
[0201]
[0301]
2
[0002]
[0102]
[0202]
[0302]
+ 1 per zone
+ 1 per zone
+ 1 per zone
+ 1 per zone
[0096]
[0196]
[0296]
[0396]
For Ademco Slow, Silent Knight Fast, Sescoa, Ademco Express, or pager formats, key-in
desired two-digit hex values from 00 to FF.
Ademco Format
Use section [4032] to program a set of default Ademco report codes from the Automatic
Report Code Programming on page 57. Then to program the remaining report codes or to
change some of the defaults, enter the individual sections and key-in the desired
two-digit hex value found in the Contact ID Report Code List on page 60.
SIA Format
Use section [4032] to program a set of SIA report codes from the Automatic Report Code
Programming on page 57. Codes that have not been set to default can be set to default
manually by entering FF in the appropriate section. To disable the reporting of an event,
enter 00 in the appropriate section.
10 | Zone Programming
96
Version 2.1
Digiplex EVO Programming Guide • Zone Programming
Worksheet 2: Zone Information
Zone
Description
Module
Eight-digit Serial Number
Input Number
Zone Definition
Partition Assignment
1
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Zone Information | 11
43
44
45
46
47
48
Zone Options
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
12 | Zone Information
Worksheet 2: Zone Information (Continued)
Zone
Description
Module
Eight-digit Serial Number
Input Number
Zone Definition
Partition Assignment
49
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
Digiplex EVO Programming Guide • Zone Programming
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
Zone Options
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
Digiplex EVO Programming Guide • Zone Programming
Worksheet 2: Zone Information (Continued)
Zone
Description
Module
Eight-digit Serial Number
Input Number
Zone Definition
Partition Assignment
97
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
Zone Information | 13
139
140
141
142
143
144
Zone Options
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
14 | Zone Information
Worksheet 2: Zone Information (Continued)
Zone
Description
Module
Eight-digit Serial Number
Input Number
Zone Definition
Partition Assignment
145
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
__________________________________________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
_______________
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
Digiplex EVO Programming Guide • Zone Programming
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
Zone Options
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
Digiplex EVO Programming Guide • Zone Programming
Worksheet 3: Zone Report Codes
Zone
#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Zone Report Codes | 15
43
44
45
46
47
48
Alarm
Report
Codes
Alarm
Restore
Report Codes
Tamper
Report
Codes
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
Tamper
Zone
Restore
#
Report Codes
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
Alarm
Report
Codes
Alarm
Restore
Report Codes
Tamper
Report
Codes
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
Tamper
Zone
Restore
#
Report Codes
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
Alarm
Report
Codes
Alarm
Restore
Report Codes
Tamper
Report
Codes
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
Tamper
Zone
Restore
#
Report Codes
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
Alarm
Report
Codes
Alarm
Restore
Report Codes
Tamper
Report
Codes
Tamper
Restore
Report Codes
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
16 | Zone Labels
Worksheet 4: Zone Labels
Digiplex EVO Programming Guide • Zone Programming
Zone
#
Zone Label
Zone
#
Zone Label
Zone
#
Zone Label
Zone
#
Zone Label
1
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
49
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
97
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
145
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
2
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
50
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
98
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
146
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
3
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
51
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
99
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
147
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
4
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
52
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
100
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
148
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
5
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
53
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
101
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
149
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
6
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
54
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
102
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
150
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
7
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
55
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
103
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
151
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
8
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
56
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
104
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
152
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
9
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
57
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
105
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
153
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
10
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
58
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
106
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
154
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
11
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
59
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
107
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
155
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
12
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
60
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
108
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
156
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
13
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
61
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
109
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
157
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
14
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
62
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
110
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
158
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
15
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
63
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
111
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
159
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
16
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
64
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
112
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
160
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
17
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
65
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
113
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
161
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
18
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
66
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
114
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
162
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
19
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
67
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
115
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
163
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
20
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
68
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
116
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
164
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
21
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
69
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
117
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
165
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
22
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
70
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
118
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
166
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
23
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
71
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
119
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
167
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
24
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
72
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
120
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
168
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
25
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
73
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
121
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
169
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
26
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
74
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
122
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
170
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
27
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
75
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
123
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
171
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
28
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
76
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
124
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
172
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
29
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
77
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
125
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
173
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
30
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
78
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
126
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
174
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
31
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
79
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
127
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
175
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
32
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
80
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
128
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
176
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
33
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
81
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
129
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
177
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
34
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
82
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
130
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
178
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
35
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
83
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
131
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
179
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
36
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
84
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
132
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
180
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
37
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
85
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
133
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
181
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
38
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
86
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
134
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
182
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
39
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
87
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
135
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
183
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
40
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
88
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
136
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
184
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
41
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
89
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
137
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
185
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
42
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
90
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
138
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
186
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
43
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
91
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
139
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
187
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
44
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
92
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
140
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
188
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
45
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
93
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
141
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
189
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
46
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
94
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
142
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
190
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
47
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
95
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
143
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
191
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
48
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
96
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
144
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
192
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Digiplex EVO • Programming Guide
Keyswitch Programming
Use the following section to program keyswitches on your EVO48 or EVO192 control panel. Keyswitch programming information is entered in worksheets 5 and 6 on
page 18.
Keyswitch Numbering
This feature allows the installer to assign a keyswitch to an addressable or hardwired detection device. To assign keyswitch numbering, proceed as follows:
1.
Enter a section number between [0501] and [0532]. These sections represent keyswitches 1 to 32, respectively.
2.
In column A, of worksheet 5 on page 18, enter the eight-digit serial number of the module, to which the keyswitch is connected.
3.
In column B, of worksheet 5 on page 18, enter the three-digit input number of the module, to which the keyswitch is connected.
Keyswitch Parameters
This feature defines the keyswitch’s partition assignment and arming method. To assign keyswitch parameters, proceed as follows:
1.
Enter a section number between [0601] and [0632]. These sections represent keyswitches 1 to 32, respectively.
2.
In column C, of worksheet 5 on page 18, enter the keyswitch definition (refer to table 9 for details). The default setting is set to disabled.
3.
In column D, of worksheet 5 on page 18, enter the desired partition to which the keyswitch is assigned (refer to table 10 for details). By default, keyswitches are
not assigned to a partition.
4.
In column E, of worksheet 5 on page 18, enter the keyswitch option (refer to table 11 for details). By default, all settings are set to OFF.
Table 9: Keyswitch definitions
Input Value Description
0
Table 10: Keyswitch partition/panic type assignment
Input Value Description
Disabled (default)
•
1
Assign keyswitch to partition 1*
•
2
Assign keyswitch to partition 2*
Assign keyswitch to partition 1
Panic type 2: medical*
3
•
•
Disarm only
Assign keyswitch to partition 3*
Assign keyswitch to partition 2
Panic type 3: fire*
•
4
•
OFF: disarm; ON: disarm only if
Stay/Instant armed
Assign keyswitch to partition 4*
5
•
•
Arm only
Assign keyswitch to partition 5*
6
•
•
Stay arming**
Assign keyswitch to partition 6*
7
•
•
Force arming**
Assign keyswitch to partition 7*
8
•
•
Instant arming**
Assign keyswitch to partition 8*
0
Momentary keyswitch
2
Maintained keyswitch
3
Generates a utility key event
on open*
1
•
•
4
Generates a utility key event
on open and close*
2
•
•
3
Assign keyswitch to partition 3
4
Assign keyswitch to partition 4
5
Assign keyswitch to partition 5
6
Assign keyswitch to partition 6
7
Assign keyswitch to partition 7
8
Assign keyswitch to partition 8
Panic input option**
* To use this keyswitch definition, one or more PGMs
must be programmed with the Utility Key event (see
Event Group 048 in table 14 on page 20).
** To use this keyswitch definition, refer to Panic Input
Option.
Input Value Description
Not assigned to a partition
(default)
Panic type 1: police*
1
5
Table 11: Keyswitch options/partition assignment
* Only applicable for keyswitch definition 5 (panic input option
in table 9). Refer to Panic Input Option for details.
* Only applicable for keyswitch definition 5 (panic input option
in table 9). Refer to Panic Input Option for details.
** Select only one of these arming types. If all are OFF,
keyswitch will use regular arming by default.
Keyswitch Arming/Disarming Report Codes
For Ademco Slow, Silent Knight Fast, Sescoa, Ademco Express, or pager formats, key-in desired two-digit hex values from 00 to FF. Use worksheet 6 on page 18 to
record settings.
Ademco Contact ID
•
•
Use section [4033] to program a set of default Ademco report codes, using table 44 (Description of the automatic report codes), on page 53.
To program the remaining report codes or change certain defaults, access the individual sections and key-in the desired two-digit hex value, found in table 48
(List of Ademco contact ID report codes), on page 58.
SIA Format
•
•
•
Use section [4033] to program a set of SIA report codes, using table 44 (Description of the automatic report codes), on page 53.
Codes that have not been set to default can be set as such manually, by entering FF in the appropriate section.
To disable the reporting of an event, enter 00 in the appropriate section.
Panic Input Option
To use the panic input option when programming keyswitch parameters in sections [0601] to [0632], proceed as follows:
1.
Enable partition panic alarm options, by referring to table 35 on page 48.
2.
Enter 5 to access the panic input option (see table 9).
3.
Enter 0, 1, or 2 to assign the type of panic. As shown in table 10, 0 = police; 1= medical; 2 = fire.
4.
Enter 1 to 8 to assign the keyswitch to partitions 1 through 8, respectively (see table 11).
Version 2.1
Keyswitch Programming | 17
18 | Keyswitch Numbering and Parameters
Worksheet 5: Keyswitch Numbering and Parameters
Keyswitch #
Description
Module
Section
A
Eight-digit Serial Number
B
Input Number
C
D
Section Keyswitch Definition Keyswitch Partition
1
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
______________________
[0501]
[0502]
[0503]
[0504]
[0505]
[0506]
[0507]
[0508]
[0509]
[0510]
[0511]
[0512]
[0513]
[0514]
[0515]
[0516]
[0517]
[0518]
[0519]
[0520]
[0521]
[0522]
[0523]
[0524]
[0525]
[0526]
[0527]
[0528]
[0529]
[0530]
[0531]
[0532]
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
[0601]
[0602]
[0603]
[0604]
[0605]
[0606]
[0607]
[0608]
[0609]
[0610]
[0611]
[0612]
[0613]
[0614]
[0615]
[0616]
[0617]
[0618]
[0619]
[0620]
[0621]
[0622]
[0623]
[0624]
[0625]
[0626]
[0627]
[0628]
[0629]
[0630]
[0631]
[0632]
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
E
Keyswitch Options
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
Digiplex EVO Programming Guide • Keyswitch Programming
Worksheet 6: Arming and Disarming with Keyswitch Report Codes
Section Keyswitch #
[0701]
[0702]
[0703]
[0704]
[0705]
[0706]
[0707]
[0708]
[0709]
[0710]
[0711]
[0712]
[0713]
[0714]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Arming
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
Section Keyswitch #
[0715]
[0716]
[0717]
[0718]
[0719]
[0720]
[0721]
[0722]
[0723]
[0724]
[0725]
[0726]
[0727]
[0728]
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Arming
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
Section Keyswitch #
[0729]
[0730]
[0731]
[0732]
29
30
31
32
Arming
___/___
___/___
___/___
___/___
Section Keyswitch #
Disarming
Section Keyswitch #
Disarming
Section Keyswitch #
Disarming
[0801]
[0802]
[0803]
[0804]
[0805]
[0806]
[0807]
[0808]
[0809]
[0810]
[0811]
[0812]
[0813]
[0814]
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
[0815]
[0816]
[0817]
[0818]
[0819]
[0820]
[0821]
[0822]
[0823]
[0824]
[0825]
[0826]
[0827]
[0828]
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
[0829]
[0830]
[0831]
[0832]
___/___
___/___
___/___
___/___
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Digiplex EVO • Programming Guide
Programmable Outputs
Use the following section to program various programmable outputs (PGMs) on your EVO48 or EVO192 control panel.
PGM Test Mode
Table 12: Test PGMs and their section numbers
Description
Section
Action
[0901]
Test PGM 1
Activates PGM 1 for eight seconds to verify if the PGM is functioning properly
[0902]
Test PGM 2
Activates PGM 2 for eight seconds to verify if the PGM is functioning properly
[0903]
Test PGM 3
Activates PGM 3 for eight seconds to verify if the PGM is functioning properly
[0904]
Test PGM 4
Activates PGM 4 for eight seconds to verify if the PGM is functioning properly
[0905]
Test PGM 5
Activates PGM 5 for eight seconds to verify if the PGM is functioning properly
PGM Delays
To record values in worksheet 7, use the PGM Delay descriptions, as well as the information appearing in table 13 (Description of PGM options).
WARNING: Considering that section numbers follow a numerical sequence, PGM activation and deactivation events for a respective PGM are skipped
when using the keypad’s programming sequence. For instance, sections [0918] and [0919] correspond to PGM 1 and one follows the other in the
programming sequence; however, the following section in the sequence ([0920], corresponds to PGM 2. Make sure to enter sections [0910] through
[0917] (see table 14) to complete activation/deactivation programming for PGM 1.
Worksheet 7: PGM Delays
Section
PGM Delay Value
[0918]
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
[0928]
[0938]
[0948]
[0958]
Range
(001
(001
(001
(001
(001
to
to
to
to
to
255
255
255
255
255
x
x
x
x
x
1
1
1
1
1
Description
sec./min.)
sec./min.)
sec./min.)
sec./min.)
sec./min.)
Default Setting
PGM 1 delay (refer to section [0919], option 2, to see whether the delay is in sec. or min.)
PGM 2 delay (refer to section [0929], option 2, to see whether the delay is in sec. or min.)
PGM 3 delay (refer to section [0939], option 2, to see whether the delay is in sec. or min.)
PGM 4 delay (refer to section [0949], option 2, to see whether the delay is in sec. or min.)
PGM 5 delay (refer to section [0959], option 2, to see whether the delay is in sec. or min.)
5
5
5
5
5
sec./min.
sec./min.
sec./min.
sec./min.
sec./min.
PGM Options
Table 13: Description of PGM options
PGM 1 [0919]
Option
PGM 2[0929]
PGM 3 [0939]
PGM 4 [0949]
PGM 5 [0959]
Description
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
1
PGM deactivation after (OFF = deactivation event;
ON = PGM timer)










2
PGM base time (OFF = seconds; ON = minutes)










3
Flexible PGM deactivation option (OFF = PGM timer
only; ON = PGM timer and/or deactivation event)










4
PGM initial state (OFF = normally open;
ON = normally closed)










-
-
-
-
-
-
-
-
-
-
5 to 8
Future use
OFF = Disabled; ON = Enabled; = Default Setting
WARNING: To use the flexible PGM Deactivation option (option 3), the PGM deactivation after option (option 1) must be ON (see table 13).
PGM Programming
Use table 14 (List of event and feature groups), on page 20 to enter data in worksheet 8. Columns A through D in worksheet 8, correspond to their respective columns
in table 14.
Worksheet 8: PGM Programming
PGM Activation
PGM Deactivation
Version 2.1
Section
PGM
A
Event Group
Section
PGM
B
Feature Group
Section
PGM
C
Start #
Section
PGM
D
End #
[0910]
[0920]
[0930]
[0940]
[0950]
[0914]
[0924]
[0934]
[0944]
[0954]
PGM 1
PGM 2
PGM 3
PGM 4
PGM 5
PGM 1
PGM 2
PGM 3
PGM 4
PGM 5
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
[0911]
[0921]
[0931]
[0941]
[0951]
[0915]
[0925]
[0935]
[0945]
[0955]
PGM 1
PGM 2
PGM 3
PGM 4
PGM 5
PGM 1
PGM 2
PGM 3
PGM 4
PGM 5
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
[0912]
[0922]
[0932]
[0942]
[0952]
[0916]
[0926]
[0936]
[0946]
[0956]
PGM 1
PGM 2
PGM 3
PGM 4
PGM 5
PGM 1
PGM 2
PGM 3
PGM 4
PGM 5
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
[0913]
[0923]
[0933]
[0943]
[0953]
[0917]
[0927]
[0937]
[0947]
[0957]
PGM 1
PGM 2
PGM 3
PGM 4
PGM 5
PGM 1
PGM 2
PGM 3
PGM 4
PGM 5
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
Programmable Outputs | 19
Digiplex EVO • Programming Guide
Event and Feature Groups
Notes for Table 14
000 = Occurs in all partitions enabled in the system (see section [3031], in 001 = Partition 1
table 18 on page 36)
002 = Partition 2
003 = Partition 3
004 = Partition 4
255 = Occurs in at least one partition enabled in the system
006 = Partition 6
007 = Partition 7
008 = Partition 8
005 = Partition 5
Table 14: List of event and feature groups
A
Event Group
Event
B
Feature Group
Feature
C
Start #
D
End #
000
Zone is OK
001 to 192
001 to 192
001
Zone is open
001 to 192
001 to 192
002
Zone is tampered
001 to 192
001 to 192
003
Zone is in fire loop trouble
001 to 192
001 to 192
004
Non-reportable event
000
Zone numbers
255 = any zone #
000
TLM trouble
000
000
Smoke detector reset
001
001
Arm with no entry delay
002
002
Arm in Stay mode
003
003
Arm in Away mode
004
004
Full arm when in Stay mode
005
005
Voice module access
006
006
Remote control access
007
007
Pc fail to communicate
008
008
Midnight
009
009
Neware user login
010
010
Neware user logout
011
011
User initiated call-up
012
012
Force answer
013
013
Force hangup
014
014
Future use
015
015
000
004
Non-reportable event
Auxiliary output manually activated
016
016
Auxiliary output manually deactivated
017
017
Voice reporting failed
018
018
FTC restore
019
019
Software access (VDMP3, Ip100, Neware, WinLoad)
020
020
IPR512 1 Registration Status
021
021
IPR512 2 registration status
022
022
IPR512 3 registration status
023
023
IPR512 4 registration status
005
006
007
User code entered on keypad
024
024
Not Used
Not Used
User codes 000 to 255
000 to 255
000 to 255
User codes 256 to 511
000 to 255
000 to 255
002
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
Not Used
Not Used
000
Door numbers
001 to 032
001 to 032
Not Used
Not Used
255
Any non-reportable event
000
001
User/card access on door
255
Any door number
000
One-touch bypass programming
000
000
000
User codes 001 to 255
001 to 255
001 to 255
001
User codes 256 to 511
000 to 255
000 to 255
002
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
Not Used
Not Used
Bypass programming access
20 | Programmable Outputs
Version 2.1
Digiplex EVO • Programming Guide
Table 14: List of event and feature groups (Continued)
A
Event Group
008
009
010
011
Event
B
Feature Group
Feature
C
Start #
D
End #
001 to 192
001 to 192
000
Zone numbers
255
Any zone number
Not Used
Not Used
000
User codes 001 to 255
001 to 255
001 to 255
001
User codes 256 to 511
000 to 255
000 to 255
002
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
000
TX delay zone alarm
Arming with master
Arming with user code
Not Used
Not Used
User codes 001 to 255
001 to 255
001 to 255
001
User codes 256 to 511
000 to 255
000 to 255
002
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
000
Keyswitch numbers
255
Any keyswitch
Not Used
Not Used
001 to 032
001 to 032
Not Used
Not Used
Arming with keyswitch
Auto arming
000
000
Arming with WinLoad
001
001
Late to close
002
002
No movement arming
003
003
Partial arming
004
004
000
012
013
014
015
016
017
018
Version 2.1
Special arming
Disarm with master
Disarm with user code
One-touch arming
005
005
Future use
006
006
Future use
007
007
(InTouch) voice module arming
008
008
Delinquency closing
009
009
Not Used
Not Used
255
Any special arming event
000
User codes 001 to 255
001 to 255
001 to 255
001
User codes 256 to 511
000 to 255
000 to 255
002
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
Not Used
Not Used
000
User codes 001 to 255
001 to 255
001 to 255
001
User codes 256 to 511
000 to 255
000 to 255
002
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
000
Keyswitch numbers
255
Any keyswitch
000
001
Not Used
Not Used
001 to 032
001 to 032
Not Used
Not Used
User codes 001 to 255
001 to 255
001 to 255
User codes 256 to 511
000 to 255
000 to 255
002
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
Not Used
Not Used
000
User codes 001 to 255
001 to 255
001 to 255
001
User codes 256 to 511
000 to 255
000 to 255
002
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
000
Keyswitch numbers
255
Any keyswitch
Disarm with keyswitch
Disarm after alarm with master
Disarm after alarm with user code
Not Used
Not Used
001 to 032
001 to 032
Not Used
Not Used
Disarm after alarm with keyswitch
Programmable Outputs | 21
Digiplex EVO • Programming Guide
Table 14: List of event and feature groups (Continued)
A
Event Group
019
020
021
Event
Alarm cancelled with master
Alarm cancelled with user code
B
Feature Group
Feature
User codes 001 to 255
001 to 255
001 to 255
001
User codes 256 to 511
000 to 255
000 to 255
002
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
Not Used
Not Used
000
User codes 001 to 255
001 to 255
001 to 255
001
User codes 256 to 511
000 to 255
000 to 255
002
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
000
Keyswitch numbers
255
Any keyswitch
255
Not Used
Not Used
000
000
One-touch Stay/Instant disarm
001
001
Disarming with winLoad
002
002
Disarming with winload after alarm
003
003
WinLoad cancelled alarm
004
004
Future use
005
005
Future use
006
006
Future use
007
007
(InTouch) voice module disarming
008
008
Not Used
Not Used
001 to 192
001 to 192
001 to 192
001 to 192
001 to 192
001 to 192
Zone alarm restore
001 to 192
001 to 192
Fire alarm restore
001 to 192
001 to 192
Zone bypassed
024
Zone in alarm
025
Fire alarm
026
027
030
Not Used
001 to 032
Special disarming
023
029
Not Used
001 to 032
Alarm cancelled with keyswitch
000
028
D
End #
000
Auto arm cancelled
022
C
Start #
Early to disarm by user
Late to disarm by user
Special alarm
22 | Programmable Outputs
Any special disarming event
000
Zone numbers
255 = any zone #
000
User codes 001 to 255
001 to 255
001 to 255
001
User codes 256 to 511
000 to 255
000 to 255
002
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
000
Not Used
Not Used
User codes 001 to 255
001 to 255
001 to 255
001
User codes 256 to 511
000 to 255
000 to 255
002
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
Not Used
Not Used
000
Emergency panic (Keys 1 & 3)
000
Medical panic (Keys 4 & 6)
001
001
Fire panic (Keys 7 & 9)
002
002
Recent closing
003
003
Police code
004
004
Zone shutdown
005
005
Future use
006
006
Future use
007
007
000
TLM alarm
008
008
Central communication failure alarm
009
009
Module tamper alarm
010
010
Missing GSM module alarm
011
011
Version 2.1
Digiplex EVO • Programming Guide
Table 14: List of event and feature groups (Continued)
A
Event Group
Event
B
Feature Group
C
Start #
D
End #
012
012
Missing IP module alarm
013
013
IP no service alarm
014
014
Missing voice module alarm
015
015
Not Used
Not Used
Feature
GSM no service alarm
030
(cont.)
031
Special alarm
(cont.)
Duress alarm by user
032
Zone shutdown
033
Zone tamper
034
Zone tamper restore
035
Special tamper
000
(cont.)
255
Any special alarm event
000
User codes 001 to 255
001 to 255
001 to 255
001
User codes 256 to 511
000 to 255
000 to 255
002
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
Not Used
Not Used
001 to 192
001 to 192
001 to 192
001 to 192
001 to 192
001 to 192
Keypad lockout
000
000
Voice lockout
001
001
Future use
000
000
AC failure
001
001
000
Zone numbers
255 = any zone #
000
Battery failure
002
002
Auxiliary current limit
003
003
Bell current limit
004
004
Bell absent
005
005
000
036
Trouble event
255
Clock trouble
006
006
Global fire loop
007
007
Any trouble event
Not Used
Not Used
TLM trouble
000
000
AC failure
001
001
Battery failure
002
002
Auxiliary current limit
003
003
Bell current limit
004
004
Bell absent
005
005
Clock trouble
006
006
Global fire loop
007
007
Not Used
Not Used
Combus fault
000
000
Module tamper
001
001
ROM/RAM error
002
002
TLM trouble
003
003
000
037
Trouble restore
255
000
038
Fail to communicate
004
004
Printer fault
005
005
AC failure
006
006
Battery failure
007
007
Auxiliary failure
008
008
Missing PCS module
000
000
GSM RF jam
002
002
GSM no service
003
003
Fail to communicate IPR512 1
004
004
Fail to communicate IPR512 2
005
005
Fail to communicate IPR512 3
006
006
Fail to communicate IPR512 4
007
007
Module trouble
001
Version 2.1
Any trouble restore event
Programmable Outputs | 23
Digiplex EVO • Programming Guide
Table 14: List of event and feature groups (Continued)
A
Event Group
Event
B
Feature Group
001 (cont.)
038
(cont.)
Module trouble
(cont.)
Feature
Missing voice module
D
End #
032
032
Missing IP module
000
000
IP no service
001
001
Fail to communicate IPR512 1
002
002
Fail to communicate IPR512 2
003
003
Fail to communicate IPR512 3
004
004
Fail to communicate IPR512 4
005
005
Not Used
Not Used
000
000
002
255
Any module trouble event
Combus fault
000
039
C
Start #
Module tamper
001
001
ROM/RAM error
002
002
TLM trouble
003
003
Fail to communicate
004
004
Printer fault
005
005
AC failure
006
006
Battery failure
007
007
Auxiliary failure
008
008
Missing PCS module
000
000
GSM RF jam supervision
002
002
GSM no service
003
003
Fail to communicate IPR512 1
004
004
Fail to communicate IPR512 2
005
005
Fail to communicate IPR512 3
006
006
Fail to communicate IPR512 4
007
007
Missing voice module
032
032
Module trouble restore
001
Missing IP module
000
000
IP no service
001
001
Fail to communicate IPR512 1
002
002
Fail to communicate IPR512 2
003
003
Fail to communicate IPR512 3
004
004
Fail to communicate IPR512 4
005
005
Not Used
Not Used
001 to 004
001 to 004
002
040
Fail to communicate on telephone
number
041
Low battery on zone
042
Zone supervision trouble
043
Low battery on zone restored
044
Zone supervision trouble restored
255
Any module trouble restore event
000
Telephone number
255
Any telephone number
000
Zone numbers
255 = any zone #
Not Used
Not Used
001 to 192
001 to 192
001 to 192
001 to 192
001 to 192
001 to 192
001 to 192
001 to 192
Power-up after total power down
000
000
Software reset (watchdog)
001
001
Test report
002
002
Listen-in request
003
003
WinLoad In (connected)
004
004
WinLoad Out (disconnected)
005
005
Installer In programming
006
006
000
045
Special events
Installer Out of programming
046
007
007
Not Used
Not Used
User codes 001 to 255
001 to 255
001 to 255
User codes 256 to 511
000 to 255
000 to 255
255
Any special event
000
001
Early to arm by user
24 | Programmable Outputs
Version 2.1
Digiplex EVO • Programming Guide
Table 14: List of event and feature groups (Continued)
A
Event Group
Event
B
Feature Group
C
Start #
D
End #
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
000
002
046
(cont.)
047
Early to arm by user
(cont.)
Late to arm by user
048
Utility key
049
Request for exit
050
Access denied
051
Door left open alarm
Feature
Not Used
Not Used
User codes 001 to 255
001 to 255
001 to 255
001
User codes 256 to 511
000 to 255
000 to 255
002
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
000
Utility key 001 to 064*†
255
Any utility key*†
000
255 = any door
number
Not Used
Not Used
001 to 064
001 to 064
Not Used
Not Used
001 to 032
001 to 032
001 to 032
001 to 032
001 to 032
001 to 032
Door numbers
052
Door forced alarm
001 to 032
001 to 032
053
Door left open restore
001 to 032
001 to 032
054
Door forced open restore
001 to 032
001 to 032
001 to 192
001 to 192
000
055
Intellizone triggered
056
Zone excluded on Force arming
057
Zone went back to arm status
058
New module assigned on combus
059
Module manually removed from
combus
255
060
Non-saved event
061
Future use
062
063
064
065
Version 2.1
Access granted to user
000
255 = any zone
Zone numbers
Any zone number
Zone numbers
Not Used
Not Used
001 to 192
001 to 192
Zone numbers
001 to 192
001 to 192
Module address
001 to 254
001 to 254
000
255 = any module Module address
001 to 254
001 to 254
000
000
000
Future use
Future Use
Future Use
000
User codes 001 to 255
001 to 255
001 to 255
001
User codes 256 to 511
000 to 255
000 to 255
002
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
Not Used
Not Used
000
Unregistered access code
000
000
000
User codes 001 to 255
001 to 255
001 to 255
001
User codes 256 to 511
000 to 255
000 to 255
002
User codes 512 to 767
000 to 255
000 to 255
003
User codes 768 to 999
000 to 231
000 to 231
255
Any user code
Not Used
Not Used
Armed
000
000
Force armed
001
001
Stay armed
002
002
Instant armed
003
003
Strobe alarm
004
004
Silent alarm
005
005
Audible alarm
006
006
Fire alarm
007
007
Ready
000
000
Exit delay
001
001
Entry delay
002
002
System in trouble
003
003
Alarm in memory
004
004
Zones bypassed
005
005
Future use
Remote control rejected
Access denied to user
Status 1
Status 2
See Notes for Table
14 on page 20
See Notes for Table
14 on page 20
Programmable Outputs | 25
Digiplex EVO • Programming Guide
Table 14: List of event and feature groups (Continued)
A
Event Group
065
(cont.)
066
Event
Status 2
(cont.)
Status 3
B
Feature Group
See Notes for Table
14 on page 20
See Notes for Table
14 on page 20
C
Start #
D
End #
Bypass, master, installer programming
006
006
Keypad lockout
007
007
Intellizone delay engaged**
000
000
Fire delay engaged
001
001
Auto arm
002
002
Arming with voice module (set until exit delay finishes)
003
003
Tamper
004
004
Zone low battery
005
005
Fire loop trouble
006
006
Zone supervision trouble
007
007
000 to 003
000 to 003
Feature
Chime in partition 1 to 4
(000 to 003 = system 1 to 4)
Smoke detector power reset
004
004
Ground start
005
005
Kiss off
006
006
Telephone ring
007
007
Bell on partition 1 to 8
(008 to 015 = partitions 1 to 8)
008 to 015
008 to 015
Pulsed alarm in partition 1 to 8
(016 to 023 = partitions 1 to 8)
016 to 023
016 to 023
Open/close Kiss off in partition 1 to 8
(024 to 031 = partitions 1 to 8)
024 to 031
024 to 031
Keyswitch/PGM inputs # 01 to 32
(032 to 063 = Keyswitch/PGM inputs # 01 to 32)
032 to 063
032 to 063
Status of access door 01 to 32
(064 to 095 = access doors 01 to 32)
064 to 095
064 to 095
Trouble in system
096
096
Trouble in dialer
097
097
Trouble in module
098
098
Trouble in combus
099
099
100 to 102
100 to 102
Time and date trouble
103
103
AC failure
104
104
Battery failure
105
105
Auxiliary current limit
106
106
Bell current limit
107
107
Bell absent
108
108
ROM error
109
109
RAM error
110
110
Future use
067**
Special status
26 | Programmable Outputs
-
Future use
111
111
TLM 1 trouble
112
112
Fail to communicate 1
113
113
Fail to communicate 2
114
114
Fail to communicate 3
115
115
Fail to communicate 4
116
116
Fail to communicate with PC
117
117
Future use
118
118
Future use
119
119
Module tamper trouble
120
120
Module ROM error
121
121
Module TLM error
122
122
Module Failure to communicate
123
123
Version 2.1
Digiplex EVO • Programming Guide
Table 14: List of event and feature groups (Continued)
A
Event Group
B
Feature Group
Event
Feature
Module printer trouble
067**
(cont.)
Special status
(cont.)
-
Clock
-
D
End #
124
124
Module AC failure
125
125
Module battery trouble
126
126
Module auxiliary failure
127
127
Missing keypad
128
128
Missing module
129
129
130 to 132
130 to 132
Global combus failure
133
133
Combus overload
134
134
Future use
070
C
Start #
Future use
135
135
Dialer relay
136
136
-
Hour
Minutes
* If a keyswitch input is used, the input must be defined as Generates a Utility Key Event on Open or Generates a Utility Key Event on Open and Close. If a remote control is used, the remote
control button must be defined as a utility key button.
** These events or event groups cannot be used for a module’s PGM programming.
† Actions that activate a utility key event.
Utility Keys
Table 15: Description of utility keys
Utility Key Event
Keypad Utility Keys
Keyswitch Inputs
(definition = [3])
Keyswitch Inputs
(definition = [4])
Remote Control
Utility key 1 remote control button
1
1&2
Keyswitch input 1 opens
Keyswitch input 1 opens
2
4&5
Keyswitch input 2 opens
Keyswitch input 1 closes
Utility key 2 remote control button
3
7&8
Keyswitch input 3 opens
Keyswitch input 2 opens
Utility key 3 remote control button
& 0 or * & 0
4
CLEAR
Keyswitch input 4 opens
Keyswitch input 2 closes
Utility key 4 remote control button
5
2&3
Keyswitch input 5 opens
Keyswitch input 3 opens
Utility key 5 remote control button
6
5&6
Keyswitch input 6 opens
Keyswitch input 3 closes
-
7
8&9
Keyswitch input 7 opens
Keyswitch input 4 opens
-
8
0 & ENTER or 0 & #
Keyswitch input 8 opens
Keyswitch input 4 closes
-
9
-
Keyswitch input 9 opens
Keyswitch input 5 opens
-
10
-
Keyswitch input 10 opens
Keyswitch input 5 closes
-
11
-
Keyswitch input 11 opens
Keyswitch input 6 opens
-
12
-
Keyswitch input 12 opens
Keyswitch input 6 closes
-
13
-
Keyswitch input 13 opens
Keyswitch input 7 opens
-
14
-
Keyswitch input 14 opens
Keyswitch input 7 closes
-
15
-
Keyswitch input 15 opens
Keyswitch input 8 opens
-
16
-
Keyswitch input 16 opens
Keyswitch input 8 closes
-
17
-
Keyswitch input 17 opens
Keyswitch input 9 opens
-
18
-
Keyswitch input 18 opens
Keyswitch input 9 closes
-

-


31
-
Keyswitch input 31 opens
Keyswitch input 16 opens
-
32
-
Keyswitch input 32 opens
Keyswitch input 16 closes
-
33
-
-
Keyswitch input 17 opens
-
34
-
-
Keyswitch input 17 closes
-

-
-

-
63
-
-
Keyswitch input 32 opens
-
64
-
-
Keyswitch input 32 closes
-
NOTE: Refer to the RTX3 Reference and Installation Manual for instructions on how to program remote control buttons.
Version 2.1
Programmable Outputs | 27
Digiplex EVO • Programming Guide
Input Speeds
Worksheet 9: Input Speeds
Section
Data: Decimal Value (001 to Description
255 x 30 msec.)
(Default Setting: 600 msec.)
Section
Data: Decimal Value (001 to Description
255 x 30 msec.)
(Default Setting: 600 msec.)
[0961]
___/___/___
Input speed of input 01
[0969]
___/___/___
Input speed of input 09 (ATZ of input 01)
[0962]
___/___/___
Input speed of input 02
[0970]
___/___/___
Input speed of input 10 (ATZ of input 02)
[0963]
___/___/___
Input speed of input 03
[0971]
___/___/___
Input speed of input 11 (ATZ of input 03)
[0964]
___/___/___
Input speed of input 04
[0972]
___/___/___
Input speed of input 12 (ATZ of input 04)
[0965]
___/___/___
Input speed of input 05
[0973]
___/___/___
Input speed of input 13 (ATZ of input 05)
[0966]
___/___/___
Input speed of input 06
[0974]
___/___/___
Input speed of input 14 (ATZ of input 06)
[0967]
___/___/___
Input speed of input 07
[0975]
___/___/___
Input speed of input 15 (ATZ of input 07)
[0968]
___/___/___
Input speed of input 08
[0976]
___/___/___
Input speed of input 16 (ATZ of input 08)
Installer Code Programming
Worksheet 10: Installer Code Programming
Section
Data
[1000]
___/___/___/___/___/___
Description
(Default Setting: 000000)
Installer code (refer to section [3001], in worksheet 20 on page 36)
User Code Options
Use the following section to program access codes when using the K641/K641R or K656 keypads. With this section you can program user codes options, partition
assignment, and access control features for users 001 to 999. Always refer to the keypad’s respective user manual for additional, pertinent information on how to
program users, as well as user labels. Complete user manuals are available on our Web site at paradox.com.
To program user code options:
1.
Press and hold 0.
2.
Enter the installer code.
3.
Enter the section you wish to program. Sections [1001] to [1999] represent user numbers 001 to 999.
4.
In User Code Options, set the desired options, by referring to table 16. Press ENTER or  to save your settings and advance to the next section.
5.
In User Area Assignment, set the desired options, by referring to table 17. Press ENTER or  to save your settings and advance to the next section.
6.
In Access Level and Schedule Assignment, enter the desired settings, by referring to figure 1.
7.
In Access Control User Options, set the desired options, by referring to table 18. Press ENTER or  to save your settings and advance to the next section.
8.
In Access Card, enter the access card’s serial number manually, or present the card to the reader which is connected to the keypad.
9.
In Remote Control Assignment, enter the remote’s serial number manually, or press a remote button twice. Remotes can also be assigned using a master code.
Table 16: User options for EVO48/EVO192
Input Value
Description
1
Access control
Disabled
2
User has access to area 2
2
Disarm on access granted
OFF
Master: user can only program
user access codes
3
User has access to area 3
3
Extended unlock delay on access
4
User has access to area 4
6
5
User has access to area 5
Add tolerance window to
schedule
ON
Full Master: user can program
user access codes, options, and
assignments
6
User has access to area 6
OFF
ON
Description
7
User has access to area 7
3
Duress
8
User has access to area 8
4
Bypass
5
Arm only
Input Value
6
Stay & Instant
7
Force
8
Input Value
User has access to area 1
2
ON
Input Value Description
Table 18: Access control user options for EVO48/EVO192
1
1
ON
Description
(Master Feature)
Table 17: User area assignment for EVO48/EVO192
OFF: access keypad’s
partition only
ON: access any partition
assigned to user
28 | User Code Options
The default setting depends on the
programming user’s assigned partitions. For
example, when a Master user – who is already
assigned to partitions 1 and 2 – programs a user
code, partitions 1 and 2 will be the default
setting for the new user.
Figure 1: Description of the Access Level and
Schedule Assignment setting.
(00) (00)
Access Level
Schedule Assignment
Enter setting from 00
(default) to 15. Default
setting grants access to
all doors.
Enter setting from 00
(default) to 15. Default
setting grants access at all
times.
7
Access code follows schedule
8
OFF: unlock and disarm area(s) on
access granted
ON: code must be entered at
security keypad, to disarm
Input Value
Description
(Arming upon Access Granted)
4
5
OFF
OFF
Disabled
ON
OFF
Regular arm
OFF
ON
Stay arm
ON
ON
Force arm
Version 2.1
Digiplex EVO • Programming Guide
Arming and Disarming Report Codes
Use the following section to program arming and disarming report codes on your EVO48 or EVO192 control panel. Use worksheet 11 to record your settings.
For Ademco Slow, Silent Knight Fast, Sescoa, Ademco Express, or pager formats, key-in desired two-digit hex values from 00 to FF.
Ademco Format
•
•
Use section [4033] to program a set of default Ademco report codes, using table 44 (Description of the automatic report codes), on page 53.
To program the remaining report codes or change certain defaults, access the individual sections and key-in the desired two-digit hex value, found in table 48
(List of Ademco contact ID report codes), on page 58.
SIA Format
•
•
•
Use section [4033] to program a set of SIA report codes, using table 44 (Description of the automatic report codes), on page 53.
Codes that have not been set to default can be set as such manually, by entering FF in the appropriate section.
To disable the reporting of an event, enter 00 in the appropriate section.
Worksheet 11: Arming and Disarming Report Codes
Section
Access
Code
[2001]
[2002]
[2003]
[2004]
[2005]
[2006]
[2007]
[2008]
[2009]
[2010]
[2011]
[2012]
[2013]
[2014]
[2015]
[2016]
[2017]
[2018]
[2019]
[2020]
[2021]
[2022]
[2023]
[2024]
[2025]
[2026]
[2027]
[2028]
[2029]
[2030]
[2031]
[2032]
[2033]
[2034]
[2035]
[2036]
[2037]
[2038]
[2039]
[2040]
[2041]
[2042]
[2043]
[2044]
[2045]
[2046]
[2047]
Version 2.1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Arming
Section
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
[2048]
[2049]
[2050]
[2051]
[2052]
[2053]
[2054]
[2055]
[2056]
[2057]
[2058]
[2059]
[2060]
[2061]
[2062]
[2063]
[2064]
[2065]
[2066]
[2067]
[2068]
[2069]
[2070]
[2071]
[2072]
[2073]
[2074]
[2075]
[2076]
[2077]
[2078]
[2079]
[2080]
[2081]
[2082]
[2083]
[2084]
[2085]
[2086]
[2087]
[2088]
[2089]
[2090]
[2091]
[2092]
[2093]
[2094]
Access
Code
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
Arming
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
Section
Access
Code
[2095] 95
[2096] 96
[2097] 97
[2098] 98
[2099] 99-999
Arming
Section
___/___
___/___
___/___
___/___
___/___
[2101]
[2102]
[2103]
[2104]
[2105]
[2106]
[2107]
[2108]
[2109]
[2110]
[2111]
[2112]
[2113]
[2114]
[2115]
[2116]
[2117]
[2118]
[2119]
[2120]
[2121]
[2122]
[2123]
[2124]
[2125]
[2126]
[2127]
[2128]
[2129]
[2130]
[2131]
[2132]
[2133]
[2134]
[2135]
[2136]
[2137]
[2138]
[2139]
[2140]
[2141]
[2142]
[2143]
[2144]
[2145]
[2146]
[2147]
Access
Disarming Section
Code
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
[2148]
[2149]
[2150]
[2151]
[2152]
[2153]
[2154]
[2155]
[2156]
[2157]
[2158]
[2159]
[2160]
[2161]
[2162]
[2163]
[2164]
[2165]
[2166]
[2167]
[2168]
[2169]
[2170]
[2171]
[2172]
[2173]
[2174]
[2175]
[2176]
[2177]
[2178]
[2179]
[2180]
[2181]
[2182]
[2183]
[2184]
[2185]
[2186]
[2187]
[2188]
[2189]
[2190]
[2191]
[2192]
[2193]
[2194]
Access
Disarming Section
Code
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
Access
Disarming
Code
[2195] 95
[2196] 96
[2197] 97
[2198] 98
[2199] 99-999
___/___
___/___
___/___
___/___
___/___
Arming and Disarming Report Codes | 29
Digiplex EVO • Programming Guide
Access Control Sections
Use the following section to program access control features, such as assigning doors, as well as schedule and holiday programming.
Assigning Doors to the System
These doors are used to program the access levels in sections [2601] to [2615]. If a door must be linked to the alarm system, install a door contact and assign it to a
zone (see Zone Programming on page 10). Use worksheet 12 to record your settings.
NOTE: Under the Door Numbering column of worksheet 12, enter the eight-digit serial number of the access control module or keypad.
Table 16: Description of the different door options
Door Option Name
Description
OR/AND door access
Each door can be programmed to grant access only to cards assigned to at least one of the door’s partitions (OR Door
Access), or to cards assigned to all the door’s assigned partitions (AND Door Access). Enabling option 1 will set the door
in OR mode; disabling it will set the door in AND mode.
2
User code access
When option 2 is disabled, the access control door is accessed by presenting the access card to the reader. When
option 2 is enabled, a reader is not needed to access the controlled door. To access the controlled door, the user must
enter an access code and then press ACC on the K641/K641R keypads, or MENU > 8, and then enter access code, when
using the K656 keypad.
3
Card and code access
When option 3 is enabled, both a valid access control card and user access code must be used. The access control card
and user access code must belong to the same user. When option 3 is disabled, either a valid access control card or
user access code must be used to access the controlled door (keypad with reader, and PosiPIN™ reader only).
4
Restrict arming on door
When option 4 is enabled, that door’s reader cannot be used to arm the system, even if the access control card has the
arming option enabled.
5
Restrict disarming on door
When option 5 is enabled, that door’s reader cannot be used to disarm the system, even if the access control card has
the disarming option enabled.
1
Worksheet 12: Assigning Doors
Section
Door #
[2201]
[2202]
[2203]
[2204]
[2205]
[2206]
[2207]
[2208]
[2209]
[2210]
[2211]
[2212]
[2213]
[2214]
[2215]
[2216]
[2217]
[2218]
[2219]
[2220]
[2221]
[2222]
[2223]
[2224]
[2225]
[2226]
[2227]
[2228]
[2229]
[2230]
[2231]
[2232]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Door Numbering
Eight-digit Serial Number
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
30 | Access Control Sections
Section
[2251]
[2252]
[2253]
[2254]
[2255]
[2256]
[2257]
[2258]
[2259]
[2260]
[2261]
[2262]
[2263]
[2264]
[2265]
[2266]
[2267]
[2268]
[2269]
[2270]
[2271]
[2272]
[2273]
[2274]
[2275]
[2276]
[2277]
[2278]
[2279]
[2280]
[2281]
[2282]
Door Options
Option
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Section
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
[2301]
[2302]
[2303]
[2304]
[2305]
[2306]
[2307]
[2308]
[2309]
[2310]
[2311]
[2312]
[2313]
[2314]
[2315]
[2316]
[2317]
[2318]
[2319]
[2320]
[2321]
[2322]
[2323]
[2324]
[2325]
[2326]
[2327]
[2328]
[2329]
[2330]
[2331]
[2332]
Door Labels
Label
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Version 2.1
Digiplex EVO • Programming Guide
Schedule Programming
Each schedule determines when users are permitted access. Schedules 001 to 015 (sections [2401] to [2415]) are primary schedules. Primary schedules are the only
schedules that can be assigned to a user access code. Schedules 016 to 032 (sections [2416] to [2432]) are secondary schedules. Secondary schedules cannot be
assigned to a user access code and can only be used as backup schedules. Use worksheet 13 to record your settings for primary schedules and worksheet 14 on
page 32, for secondary schedules.
WARNING: The Start and End Time of a schedule cannot cross over into another day. For example, to program a shift from 10 PM to 6 AM the next morning,
you must program the schedule as follows: Schedule A – start time: 22:00 and end time: 23:59; then program Schedule B – start time: 00:00 and
end time: 06:00. The schedule will not be interrupted between 23:59 and 00:00.
Primary Schedules
Worksheet 13: Programming Primary Schedules
Section
Schedule
[2401]
001
[2402]
002
[2403]
003
[2404]
004
[2405]
005
[2406]
006
[2407]
007
[2408]
008
[2409]
009
[2410]
010
[2411]
011
[2412]
012
[2413]
013
[2414]
014
[2415]
015
Version 2.1
Start Time
(From)
Interval
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
End Time
(To)
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
S
M
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Days of the Week (Turn ON or OFF)
T
W
T
F
S
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
H
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
Access Control Sections | 31
Digiplex EVO • Programming Guide
Secondary Schedules
Worksheet 14: Programming Secondary Schedules
Section
Schedule
[2401]
016
[2402]
017
[2403]
018
[2404]
019
[2405]
020
[2406]
021
[2407]
022
[2408]
023
[2409]
024
[2410]
025
[2411]
026
[2412]
027
[2413]
028
[2414]
029
[2415]
030
[2415]
031
[2415]
032
Start Time
(From)
Interval
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
End Time
(To)
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
S
M
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Days of the Week (Turn ON or OFF)
T
W
T
F
S
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
H
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
Backup Schedules
Each programmed schedule (see Schedule Programming on page 31) can be backed-up or linked to another schedule. The backup will be used in the event that the
first schedule is invalid. In worksheet 15, enter the three-digit number of the schedule you wish to use as the backup. For instance, if you wish to back-up Schedule
001 to Schedule 011, enter 011 in section [2501].
The control panel will verify up to eight linked schedules, one after another, until it determines whether the card or code is valid. For example, if Schedule 001 is
linked to Schedule 005, and Schedule 005 is linked to Schedule 030, then the control panel will verify Schedules 001, 005 and 030.
Worksheet 15: Programming Backup Schedules
Section Schedule
Backup Schedule
Section Schedule
Backup Schedule
[2501]
001
___/___/___
[2517]
017
___/___/___
[2502]
002
___/___/___
[2518]
018
___/___/___
[2503]
003
___/___/___
[2519]
019
___/___/___
[2504]
004
___/___/___
[2520]
020
___/___/___
[2505]
005
___/___/___
[2521]
021
___/___/___
[2506]
006
___/___/___
[2522]
022
___/___/___
[2507]
007
___/___/___
[2523]
023
___/___/___
[2508]
008
___/___/___
[2524]
024
___/___/___
[2509]
009
___/___/___
[2525]
025
___/___/___
[2510]
010
___/___/___
[2526]
026
___/___/___
[2511]
011
___/___/___
[2527]
027
___/___/___
[2512]
012
___/___/___
[2528]
028
___/___/___
[2513]
013
___/___/___
[2529]
029
___/___/___
[2514]
014
___/___/___
[2530]
030
___/___/___
[2515]
015
___/___/___
[2531]
031
___/___/___
[2516]
016
___/___/___
[2532]
032
___/___/___
32 | Access Control Sections
Version 2.1
Digiplex EVO • Programming Guide
Access Levels
Each access level is a combination of access control doors. For example, if option 1 in the first screen is enabled in section [2601], Level 01 will allow access only to
Door 01. Use worksheet 16 to record your settings.
Worksheet 16: Programming Access Levels
Access to Doors (Turn ON or OFF access)
Second Screen
Third Screen
(Doors 09 to 16)
(Doors 17 to 24)
First Screen
(Doors 01 to 08)
Fourth Screen
(Doors 25 to 32)
Section
Level
[2601]
01
1
2 3
4 5
6
7 8
1
2 3
4
5 6
7 8
1
2 3
4
5 6
7
8
1
2
3 4
5 6
7
8
[2602]
02
1
2 3
4 5
6
7 8
1
2 3
4
5 6
7 8
1
2 3
4
5 6
7
8
1
2
3 4
5 6
7
8
[2603]
03
1
2 3
4 5
6
7 8
1
2 3
4
5 6
7 8
1
2 3
4
5 6
7
8
1
2
3 4
5 6
7
8
[2604]
04
1
2 3
4 5
6
7 8
1
2 3
4
5 6
7 8
1
2 3
4
5 6
7
8
1
2
3 4
5 6
7
8
[2605]
05
1
2 3
4 5
6
7 8
1
2 3
4
5 6
7 8
1
2 3
4
5 6
7
8
1
2
3 4
5 6
7
8
[2606]
06
1
2 3
4 5
6
7 8
1
2 3
4
5 6
7 8
1
2 3
4
5 6
7
8
1
2
3 4
5 6
7
8
[2607]
07
1
2 3
4 5
6
7 8
1
2 3
4
5 6
7 8
1
2 3
4
5 6
7
8
1
2
3 4
5 6
7
8
[2608]
08
1
2 3
4 5
6
7 8
1
2 3
4
5 6
7 8
1
2 3
4
5 6
7
8
1
2
3 4
5 6
7
8
[2609]
09
1
2 3
4 5
6
7 8
1
2 3
4
5 6
7 8
1
2 3
4
5 6
7
8
1
2
3 4
5 6
7
8
[2610]
10
1
2 3
4 5
6
7 8
1
2 3
4
5 6
7 8
1
2 3
4
5 6
7
8
1
2
3 4
5 6
7
8
[2611]
11
1
2 3
4 5
6
7 8
1
2 3
4
5 6
7 8
1
2 3
4
5 6
7
8
1
2
3 4
5 6
7
8
[2612]
12
1
2 3
4 5
6
7 8
1
2 3
4
5 6
7 8
1
2 3
4
5 6
7
8
1
2
3 4
5 6
7
8
[2613]
13
1
2 3
4 5
6
7 8
1
2 3
4
5 6
7 8
1
2 3
4
5 6
7
8
1
2
3 4
5 6
7
8
[2614]
14
1
2 3
4 5
6
7 8
1
2 3
4
5 6
7 8
1
2 3
4
5 6
7
8
1
2
3 4
5 6
7
8
[2615]
15
1
2 3
4 5
6
7 8
1
2 3
4
5 6
7 8
1
2 3
4
5 6
7
8
1
2
3 4
5 6
7
8
Holidays
When H is enabled in a schedule, access is permitted to users during the days programmed in the sections below. Use worksheet 17 to record your settings.
Worksheet 17: Programming Holidays
Days
Section
First Screen
(Days 01 to 08)
Month
Second Screen
(Days 09 to 16)
Third Screen
(Days 17 to 24)
Fourth Screen
(Days 25 to 31)
[2701]
January
1
2 3
4
5 6
7 8
1
2 3
4 5
6
7 8
1 2
3
4 5
6
7 8
1
2 3
4
5 6
7
*
[2702]
February
1
2 3
4
5 6
7 8
1
2 3
4 5
6
7 8
1 2
3
4 5
6
7 8
1
2 3
4
5 6
7
*
[2703]
March
1
2 3
4
5 6
7 8
1
2 3
4 5
6
7 8
1 2
3
4 5
6
7 8
1
2 3
4
5 6
7
*
[2704]
April
1
2 3
4
5 6
7 8
1
2 3
4 5
6
7 8
1 2
3
4 5
6
7 8
1
2 3
4
5 6
7
*
[2705]
May
1
2 3
4
5 6
7 8
1
2 3
4 5
6
7 8
1 2
3
4 5
6
7 8
1
2 3
4
5 6
7
*
[2706]
June
1
2 3
4
5 6
7 8
1
2 3
4 5
6
7 8
1 2
3
4 5
6
7 8
1
2 3
4
5 6
7
*
[2707]
July
1
2 3
4
5 6
7 8
1
2 3
4 5
6
7 8
1 2
3
4 5
6
7 8
1
2 3
4
5 6
7
*
[2708]
August
1
2 3
4
5 6
7 8
1
2 3
4 5
6
7 8
1 2
3
4 5
6
7 8
1
2 3
4
5 6
7
*
[2709] September
1
2 3
4
5 6
7 8
1
2 3
4 5
6
7 8
1 2
3
4 5
6
7 8
1
2 3
4
5 6
7
*
[2710]
October
1
2 3
4
5 6
7 8
1
2 3
4 5
6
7 8
1 2
3
4 5
6
7 8
1
2 3
4
5 6
7
*
[2711]
November
1
2 3
4
5 6
7 8
1
2 3
4 5
6
7 8
1 2
3
4 5
6
7 8
1
2 3
4
5 6
7
*
[2712]
December
1
2 3
4
5 6
7 8
1
2 3
4 5
6
7 8
1 2
3
4 5
6
7 8
1
2 3
4
5 6
7
*
Keypad Numbering
Use the following section to number the different keypads configured to your system.
Sections [2801] to [2832] are used solely for the purpose of identifying a keypad in the event buffer. Enter the eight-digit serial number of the keypad you wish to
label as Keypad x, where x represents numbers 1 to 32 (e.g., Keypad 12). The event buffer will then display any events pertaining to this keypad, as Keypad 12. Use
worksheet 18 on page 34 to record your settings.
Version 2.1
Keypad Numbering | 33
Digiplex EVO • Programming Guide
Worksheet 18: Numbering Keypads
Section
Keypad #
Eight-digit Serial Number
Section
Keypad #
Eight-digit Serial Number
[2801]
[2802]
[2803]
[2804]
[2805]
[2806]
[2807]
[2808]
[2809]
[2810]
[2811]
[2812]
[2813]
[2814]
[2815]
[2816]
1
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
[2817]
[2818]
[2819]
[2820]
[2821]
[2822]
[2823]
[2824]
[2825]
[2826]
[2827]
[2828]
[2829]
[2830]
[2831]
[2832]
17
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
___/___/___/___/___/___/___/___
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Remote Control Programming
Use the following section to program the various remote controls in your EVO system.
It is possible to configure up to 16 different button templates, which are then assigned to individual users. Each user is pre-programmed with a default button
pattern for their remote control: (1 B) (C 0) (template 0).
NOTE: Button definitions and partition/one-touch definitions are linked together to create a button template. For example, Template 0 is comprised of button
definition [2900] together with partition/one-touch definition [2916].
Remote Control Templates
To use REM3 templates:
1.
Define the 16-button definitions in sections [2900] to [2915].
2.
Define the 16-partition/one-touch definitions in sections [2916] to [2931].
3.
Define which button template is used as the default for remotes in section [2940].
4.
Assign button templates to users in section [2941].
Use the information in tables 17 and 18, as well as figure 2, to enter data in worksheet 19 on page 35.
Table 17: Template data for remote control programming
Entry
Function
K641/K641R
Section
Name
Description
[2940]
Default button
template
To select a button template as the default template, enter 00
to 15, representing button templates in sections [2900] to
[2915].
[2941]
Assign button
template
To assign a button template to a user, select the user when
prompted, then enter 00 to 15, representing button templates
in sections [2900] to [2915]. If user 000 is selected, all users are
modified.
K656
0
0
Button disabled
1
1
Regular arm
2
2
Stay arm
3
3
Instant arm
4
4
Force arm
5
5
Utility key 5
6
6
Utility key 6
7
7
-
8
8
Panic 1
9
9
Panic 2
A = STAY
A = ARM
Panic 3
B = FORCE
B = SLEEP
Utility key 1
C = ARM
C = STAY
Utility key 2
D = DISARM
D = OFF
Utility key 3
E = BYP
E = MENU
Utility key 4
F = MEM
Table 18: Test PGMs and their section numbers
F=
34 | Remote Control Programming
Figure 2: Entering data for section [2916] on a LCD keypad (use for worksheet 19 on page 35).
Section #
Default
(All User’s Partitions)
One-touch
PGM Keys
Default
(No Partitions)
One-touch
Disarm Keys
-
Version 2.1
Digiplex EVO Programming Guide • Remote Control Programming
Worksheet 19: Programming Remote Controls
REM3 Remote Control
Template
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Default Data
Section
[2900]
[2901]
[2902]
[2903]
[2904]
[2905]
[2906]
[2907]
[2908]
[2909]
[2910]
[2911]
[2912]
[2913]
[2914]
[2915]
REM1/REM2/RAC1/RAC2
PGM 1
[9]
PGM 2
[0]
PGM 3
[x]
PGM 4
[]
PGM 5
[ ]
PGM 6
[ ]
PGM 3 & 4
[x] + []
PGM 5 & 6
[ ]+[ ]
1*
B*
C*
0*
5
6
0
0
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
1
2
Section
Default = 0
(All user’s partitions)
Default = F
(No partitions)
0
[2916]
[2917]
[2918]
[2919]
[2920]
[2921]
[2922]
[2923]
[2924]
[2925]
[2926]
[2927]
[2928]
[2929]
[2930]
[2931]
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
3
4
5
6
7
8
9
10
11
12
Programming Remote Controls | 35
13
14
15
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
One-touch Keys
Template
2
1
B
C
Disabled
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
_____
Section
Partitions **
1
+
+
One-touch PGM Keys
One-touch Disarm Keys
 = Disabled (default)
















 = Enabled
















* REM1/RAC1 and REM2/RAC2 remotes only use the data in these columns.
** If 0 is entered, the associated buttons will control all partitions to which the user is assigned. If F is entered, the associated buttons will be disabled.
[2900]
[2901]
[2902]
[2903]
[2904]
[2905]
[2906]
[2907]
[2908]
[2909]
[2910]
[2911]
[2912]
[2913]
[2914]
[2915]
Digiplex EVO • Programming Guide
Control Panel Settings
Use the following section to record control panel settings for your EVO system. Use worksheet 20 to record your settings.
Table 17: Daylight Saving Time (DST) schedule for EVO48/EVO192
Input Value Schedule Used
Input Value Schedule Used
000
Mexico; St.-Johns; Bahamas; Turks and Caicos
010
New-Zealand; Chatham
001
Cuba
011
Tonga
002
Brazil
012
Iraq; Syria
003
Chile
013
Israel (TBC)
004
Falkland Islands
014
Lebanon; Kyrgyzstan
005
Paraguay
015
Palestine
006
European Union; United Kingdom; Greenland
016
Egypt
007
Russia and surrounding countries
017
Namibia
008
South Australia; Victoria; Australian Capital Territory; New
South Wales
018
Canada; United States (default)
009
Tasmania; Lord Howe Island
019
New Zealand
Worksheet 20: Control Panel Settings
Section Data
Description
[3001] __/__/__
Installer lock
Default
Setting
000
[3010] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/ PC phone number (32 digits)
-
[3011] __/__/__/__
Panel identification
0000
[3012] __/__/__/__
PC password
0000
[3020] __/__
Panel partition (00-08)
00
[3021] __/__
Trouble shutdown (00-15)
00
[3022] __/__/__
DST schedule (see table 17)
018
System Options
Use the following section to program system options on your EVO system. Table 18 provides information on sections [3029] through [3035].
Table 18: Description of sections [3029] to [3035]
OFF
ON
1
Enable if using an RTX3 without
an K641 / K641R

Disabled

Enabled
2
Future use

Disabled

Enabled
Section
Section [3030]
System Options 2
Option Description
Option Description
OFF
ON
1
PGM 1 = Two-wire smoke detector
input (255)

Disabled

Enabled
2
No bell cut-off during pulse alarm

Disabled

Enabled
3
Daylight Saving Time
(see table 17)

Disabled

Enabled
4
Shabbat feature

Disabled

Enabled
5
Battery charge current

350 mA

850 mA
6
AC failure not displayed as trouble 
Disabled

Enabled
3
Future use

Disabled

Enabled
4
Future use

Disabled

Enabled
5
Future use

Disabled

Enabled
6
Future use

Disabled

Enabled
7
Future use

Disabled

Manually
7
Clear bell limit trouble

On restore

Manually
8
Future use

Disabled

Enabled
8
Combus speed*

Normal

High
1
Partition 1

Disabled

Enabled
1
Bell/siren output in partition 1

Disabled

Enabled
2
Partition 2

Disabled

Enabled
2
Bell/siren output in partition 2

Disabled

Enabled
3
Partition 3

Disabled

Enabled
3
Bell/siren output in partition 3

Disabled

Enabled
4
Partition 4

Disabled

Enabled
4
Bell/siren output in partition 4

Disabled

Enabled
5
Partition 5 (EVO192 only)

Disabled

Enabled
5
Bell/siren output in partition 5

Disabled

Enabled
6
Partition 6 (EVO192 only)

Disabled

Enabled
6
Bell/siren output in partition 6

Disabled

Enabled
7
Partition 7 (EVO192 only)

Disabled

Enabled
7
Bell/siren output in partition 7

Disabled

Enabled
8
Partition 8 (EVO192 only)

Disabled

Enabled
8
Bell/siren output in partition 8

Disabled

Enabled
36 | Control Panel Settings
Section [3032]
Partition Options 2
Section [3031]
Partition Options 1
Section [3029]
System Options 1
Section
Version 2.1
Digiplex EVO • Programming Guide
Table 18: Description of sections [3029] to [3035] (Continued)
ON
Multiple actions in user menu

Disabled

Enabled
2
User code length

Fixed

Flexible
3
User code length (if option 2
is OFF)

4 digits

6 digits
4
Power save mode

Disabled

Enabled
5
Bypass not displayed while system
is armed

Disabled

Enabled
Trouble latch

Disabled

6
Section [3035]
System Options 5
OFF
1
Section
Option Description
1&2
Section [3034]
System Options 4
Option Description
Section [3033]
System Options 3
Section
Wireless Transmitter Supervision
Options (see table 19)
OFF


ON
See table
19


See table
19
3
Generate supervision failure if
detected on a bypassed
wireless zone

Yes

No
4
Restrict arming on a wireless
transmitter supervision failure

Disabled

Enabled
5&6
Enabled
Zone & Module Tamper
Recognition Options
(see table 20)


7
EOL resistor on hardwire zones

Disabled

Manually
7
Generate tamper if detected on
bypass zone

8
Zone doubling (ATZ)

Disabled

Enabled
8
Restrict arming on tamper trouble 
1
Restrict arming on AC failure

Disabled

Enabled
2
Restrict arming on battery failure

Disabled

Enabled
3
Restrict arming on bell or auxiliary
failure

Disabled

Enabled
4
Restrict arming on TLM failure

Disabled

Enabled
5
Restrict arming on module
troubles

Disabled

Enabled
6
Account number transmission

Partition #

Tel #
7
Transmit zone status on
serial port**

Disabled

Enabled
8
Serial port baud rate

38,400

57,600
See table
20


See table
20
Yes

No
Disabled

Enabled
= Default
* When the combus speed is changed, all operations on the system will be suspended for
approximately one minute, while the system adjusts itself.
** This option is used by certain event monitoring softwares, such as Hyperterminal. With
WinLoad and printers, it is always being transmitted.
WARNING: In option 4 of section [3030], a 40 VA transformer is required when selecting the 850 mA battery charge current. Using a 20 VA transformer
with a battery charge current of 850 mA may damage the system.
Table 19: Wireless transmitter supervision options; options 1 and 2 for section [3034]
Option
Description
1
2
OFF
OFF
Disabled (default)
OFF
ON
Generates trouble only (when armed or disarmed)
ON
OFF
When armed: follows zone types (see Zone Programming on page 10)
When disarmed: generates trouble only
ON
ON
When armed: follows zone types (see Zone Programming on page 10)
When disarmed: generates audible alarm
Table 20: Zone and module tamper recognition options; options 5 and 6 for section [3034]
Option
Description
5
6
OFF
OFF
Disabled (default)
OFF
ON
Generates trouble only (when armed or disarmed)
ON
OFF
When armed: follows zone types (see Zone Programming on page 10) for zone tamper;
generates trouble for module tamper
When disarmed: generates trouble only
ON
ON
When armed: follows zone types (see Zone Programming on page 10)
When disarmed: generates audible alarm
NOTE: For instructions on wiring a panel for tamper recognition, refer to the Digiplex EVO Reference and Installation Manual (available online only).
Version 2.1
System Options | 37
Digiplex EVO • Programming Guide
Dialer Options
Use the following section to program dialer options on your EVO system. Table 21 provides information on sections [3036] and [3037].
Table 21: Description of sections 3036 to 3037
Option Description
1&2
Section [3036]
Dialer Options 1
3
OFF
Telephone line monitoring (TLM;
see table 22)
Dialer (reporting to monitoring
station)



See table
22
Disabled
ON



Section
See table
22
Option Description
OFF
ON
1
Call back

Disabled

Enabled
2
Automatic event buffer
transmission

Disabled

Enabled
Enabled
Section [3037]
Dialer Options 2
Section


3&4
AutoTest report transmission
options (see AutoTest Report
Settings on page 39)
5
Keypad beep on successful
arming/disarming report

Disabled

Enabled
6
Alternate dialing

Disabled

Enabled

See table
23

See table
23
4
Dialing method

Pulse

Tone
(DTMF)
5
Pulse ratio
(E.U. = Europe; N.A. = North
America)

1:2 (E.U.)

1:1.5 (N.A.)
6
Busy tone detection

Disabled

Enabled
7
Switch to pulse dialing on fifth
attempt

Disabled

Enabled
7
Dial tone delay (if no dial tone)

Force dial

Hang up
8
Bell/siren upon communication
failure, if system is armed

Disabled

Enabled
8
Report zone restore
ON = Upon zone closure
OFF = Upon bell cut-off

Disabled

Enabled
= Default
Table 22: Telephone line monitoring (TLM) options; options 1 and 2 for section [3036]
Option
Description
1
2
OFF
OFF
OFF
ON
When armed: generates an audible alarm
ON
OFF
When armed: generates a trouble
ON
ON
TLM silent alarm: becomes an audible alarm
Disabled (default)
Table 23: AutoTest report transmission options; options 3 and 4 for section [3037]
Option
Description
3
4
OFF
OFF
Transmit the test report code every time the days programmed in section [3040] have
elapsed, at the time programmed in section [3041]; (default)
OFF
ON
When armed: transmit test report code every time the time programmed in section
[3042] has elapsed
When disarmed: transmit test report code every time the time programmed in section
[3043] has elapsed
ON
OFF
The control panel will transmit the test report code every hour, on the minute value
programmed in section [3041] (the last two digits); the first two digits of section [3041]
will be ignored; for example, if 10:25 was programmed in section [3041], the test report
code would be transmitted at the 25th minute of every hour; i.e., 11:25, 12:25, etc.
ON
ON
The test report code will be transmitted when one or more of the conditions of the
second and third options, listed above, are met; i.e., option 3 = OFF and option 4 = ON,
or option 3 = ON and option 4 = OFF
38 | Dialer Options
Version 2.1
Digiplex EVO • Programming Guide
Additional Options
Use the following section to program additional options on your EVO system. Table 24 provides information on sections [3038]. Use worksheets 21, 22, and 23 to
record your settings.
Table 24: Description of section [3038]
Option Description
Section [3038]
Access Control Options
Section
OFF
ON
1
Access control feature

Disabled

Enabled
2
Log Request for Exit in event
buffer*

Disabled

Enabled
3
Log Door Left Open Restore in
event buffer

Disabled

Enabled
4
Log Door Forced Restore in event
buffer

Disabled

Enabled
5
Burglar alarm on forced door

Disabled

Enabled
6
Skip exit delay when arming with
access card

Disabled

Enabled
7
Burglar alarm on door left open

Disabled

8
Who has access during clock loss

All users

= Default
* Also includes users with 00 for schedule access.
Enabled
Masters*
WARNING: Since Request for Exit events can occur often, the event buffer may fill up quickly.
Schedule Tolerance Window
Worksheet 21: Schedule Tolerance Window
Section
[3039]
Data
___/___/___
Description
(x 1 min.)
Default Setting
Schedule tolerance window
000
AutoTest Report Settings
Worksheet 22: AutoTest Report Settings
Section
[3040]
Data
___/___/___
Description
(x 1 day; 000 = disabled)
Default Setting
Schedule tolerance window
000
[3041] ___/___ : ___/___ (hr. 00-23 & min. 00-59)
AutoTest report time of day
00:00
[3042]
___/___/___
(000-255 x 1 min.)
Armed report delay
5 minutes
[3043]
___/___/___
(000-255 x 1 min.)
Disarmed report delay
60 minutes
NOTE: Refer to table 23 on page 38 for details
Timings
Worksheet 23: Timings Settings
Section
Data
Description
Default Setting
[3051]
___/___/___
(000-255)
Ring counter
[3052]
___/___/___
(000-255 x 4 sec.)
Answering machine delay override delay
32 seconds
008
[3053]
___/___/___
(000-255 x 2sec.)
TLM fail timer
32 seconds
[3054]
___/___/___
(000-127 x 1sec.)
Delay between dialing attempts
20 seconds
[3055]
___/___/___
(000-255 x 1 sec.; 000 = instant report) Delay alarm transmission timer
[3056]
___/___/___
(000-255 x 1 attempt)
Maximum dialing attempts
[3057]
___/___/___
(000-127 x 1 second)
Pager delay before data transmission
[3058]
___/___/___
(000-255 x 1 min.; 000 = instant report) Delay power failure report
[3059]
___/___/___
(000-255 x 1 repeat; 000 = no repeat)
Repeat pager report code transmission
[3060]
___/___/___
(000-255 x 1 min.)
Power failure restore delay report
000
8 attempts
20 seconds
30 minutes
000
030 minutes
Communication Settings
Use the following section to program communication settings on your EVO system.
Account Numbers
Use worksheet 24 on page 40 to record your settings.
WARNING: Only the SIA format supports the 0 = 0 digit in its account numbers. Account numbers that use other reporting formats do not support the
0 = 0 digit. In its place, enter A by pressing STAY (for the K641/K641R keypads), or by pressing ARM (for the K656 keypad). When using the SIA format, and
the account number transmission (see option 6, in section [3035] on page 37) corresponds to the partition, the control panel only uses the partition 1
account number programmed in section [3061], but the report code includes the partition number.
Version 2.1
Additional Options | 39
Digiplex EVO • Programming Guide
Worksheet 24: Account Number Settings
Section
Data (Hex Value: 0000-FFFF)
Description
Default Setting
[3061]
___/___/___/___
(If less than four digits, press ENTER)
Account number 1 (partition 1* / MSTN 1**)
0000
[3062]
___/___/___/___
(If less than four digits, press ENTER)
Account number 2 (partition 2* / MSTN 2**)
0000
[3063]
___/___/___/___
(If less than four digits, press ENTER)
Account number 3 (partition 3* / MSTN 3**)
0000
[3064]
___/___/___/___
(If less than four digits, press ENTER)
Account number 4 (partition 4* / MSTN 4**)
0000
[3065]
___/___/___/___
(If less than four digits, press ENTER)
Account number 5 (partition 5* / NA**)
0000
[3066]
___/___/___/___
(If less than four digits, press ENTER)
Account number 6 (partition 6* / NA**)
0000
[3067]
___/___/___/___
(If less than four digits, press ENTER)
Account number 7 (partition 7* / NA**)
0000
[3068]
___/___/___/___
(If less than four digits, press ENTER)
Account number 8 (partition 8* / NA**)
0000
* Option 6 in section [3035] is disabled.
** Option 6 in section [3035] is enabled.
NOTE: MSTN is the abbreviation for Monitoring Station Telephone Number.
Reporting Formats
Use worksheets 25 and 26 to record your settings.
Table 25: Reporting formats for section [3070]
Input Value Description
0
Input Value
Description
Ademco Slow (1400 Hz, 1900 Hz, 10 BPS)
5
Ademco contact ID
1
Silent Knight Fast (1400 Hz, 1900 Hz, 20 BPS)
6
SIA FSK (level 2)
2
Sescoa (2300 Hz, 1800 Hz, 20 BPS)
7
Pager
3
Ademco Express (DTMF 4+2)
4
Pager contact ID
NOTE: For more information on contact ID and SIA reporting formats, see table 44 (Description of the automatic report codes), on page 53.
Worksheet 25: Reporting Formats for Section [3070]
Section
Tel. # 1 Format
Tel. # 2 Format
Tel. # 3 Format
[3070]
___
___
___
Tel. # 4 Format Description
___
Reporting formats for telephone numbers 1 to 4 / IP Receiver 1 to 4
NOTE: Use the same format for each number. Only the pager format can be used with other reporting formats.
Table 26: Special telephone number keys for the different keypads
Function
K641/K641R
K656
*
#
STAY
STAY
Grafica
FORCE
SLEEP
Switch to tone dialing (T)
ARM
ARM
Wait for second dial tone (W)
DISARM
OFF
4-second pause (P)
BYP
MENU
Clear
CLEAR
CLEAR
Left action key (clear)
Delete
TRBL
TRBL
-
#
(Press key until desired letter/
symbol appears)
Delete from cursor to the end
ACC
ACC
-
Insert space
MEM
MEM
-
Dial 9 for outside line
9 + STAY
9 + STAY
-
WARNING: To disable call-waiting for North American installations using either contact ID or SIA reporting formats, enter *70, and then either P (4-second
pause) or W (wait for second dial tone) before entering the phone number. This applies to sections [3071] to [3074] (see worksheet 26).
Worksheet 26: Reporting Formats for Sections [3071] to [3074]
Section Data (Press ENTER if less than 32 digits)
Description
[3071] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/ Monitoring station/pager telephone # 1
[3072] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/ Monitoring station/pager telephone # 2
[3073] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/ Monitoring station/pager telephone # 3
[3074] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/ Monitoring station/pager telephone # 4
40 | Communication Settings
Version 2.1
Digiplex EVO • Programming Guide
System Event Call Direction
Use the following section to program system event call directions on your EVO system. Table 27 provides information on sections [3080] and [3081].
Table 27: Description of sections [3080] to [3081]
Option Description
Section [3080]
System Troubles & Trouble Restores
1
OFF
Call telephone # 1/IP receiver # 1

ON
Section
Option Description
OFF
ON
Disabled

Enabled
1
Call telephone # 1/IP receiver # 1

Disabled

Enabled
2
Call telephone # 2/IP receiver # 2

Disabled

Enabled
2
Call telephone # 2/IP receiver # 2

Disabled

Enabled
3
Call telephone # 3/IP receiver # 3

Disabled

Enabled
3
Call telephone # 3/IP receiver # 3

Disabled

Enabled
4
Call telephone # 4/IP receiver # 4

Disabled

Enabled
4
Call telephone # 4/IP receiver # 4

Disabled

Enabled
5
Backup on telephone # 1/IP
receiver # 1

Disabled

Enabled
5
Backup on telephone # 1/IP
receiver # 1

Disabled

Enabled
6
Backup on telephone # 2/IP
receiver # 2

Disabled

Enabled
6
Backup on telephone # 2/IP
receiver # 2

Disabled

Enabled
7
Backup on telephone # 3/IP
receiver # 3

Disabled

Enabled
7
Backup on telephone # 3/IP
receiver # 3

Disabled

Enabled
8
Backup on telephone # 4/IP
receiver # 4

Disabled

Enabled
8
Backup on telephone # 4/IP
receiver # 4

Disabled

Enabled
Section [3081]
Special Reporting
Section
= Default
NOTE: For sections [3080] and [3081], enable only one of options 5 to 8.
VDMP3 Voice Module
Use the following section to program the VDMP3 Voice Module on your EVO system. Use worksheets 27 and 28 to record your settings.
You can program up to eight telephone numbers which the VDMP3 will call in sequence, in case of an alarm. Telephone numbers should be programmed in a
priority-based sequence, as the VDMP3 will begin with telephone number 1. See table 28 for information on sections [3087] and [3090].
Table 28: Description of sections [3087] and [3090]
Option Description
OFF
ON
Section
Option Description
OFF
1
Feature (PGM) 1

Disabled

Enabled
1
Arm/disarm
2
Feature (PGM) 2

Disabled

Enabled
2
Voice reporting
3
Feature (PGM) 3

Disabled

Enabled
3
Report AC/battery trouble
4
Feature (PGM) 4

Disabled

Enabled
4
Inhibit disarming on voice module 
5
Feature (PGM) 5

Disabled

Enabled
6
Feature (PGM) 6

Disabled

Enabled
7
Feature (PGM) 7

Disabled

Enabled
Disabled

Enabled
8
Feature (PGM) 8

Section [3090]
VDMP3 Functions
Section [3087]
VDMP3 Features (PGM)
Section

ON
Disabled


Disabled

Enabled

Disabled

Enabled
Disabled

Enabled
Enabled
= Default for options 1 and 2;  for option 3.
= Default
NOTE: To see how the VDMP3 features relate to the EVO utility key functions, refer to the Digiplex EVO Reference and Installation Manual (available online only).
Worksheet 27: VDMP3 Settings
Section
Data
Description
Default Setting
[3088]
___/___/___
(000-127 x 1 sec.)
Delay before sending the voice message
003
[3089]
___/___/___
(000-255 x 1 repetition)
Defines the number of times the voice message is repeated
008
Worksheet 28: VDMP3 functions for Sections [3091] to [3098]
Section Data (Press ENTER if less than 32 digits)
Description
[3091] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/
Voice module telephone number 1
[3092] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/
Voice module telephone number 2
[3093] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/
Voice module telephone number 3
[3094] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/
Voice module telephone number 4
[3095] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/
Voice module telephone number 5
[3096] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/
Voice module telephone number 6
[3097] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/
Voice module telephone number 7
[3098] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/
Voice module telephone number 8
NOTE: For extra key functions, see table 26 (Special telephone number keys for the different keypads), on page 40.
Version 2.1
System Event Call Direction | 41
Digiplex EVO • Programming Guide
Table 29: Description of sections [3133] to [3833]
Option
Partition 1
[3133]
Description
Partition 2
[3233]
Partition 3
[3333]
Partition 4
[3433]
Partition 5
[3533]
Partition 6
[3633]
Partition 7
[3733]
Partition 8
[3833]
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
1
Telephone number 1
















2
Telephone number 2
















3
Telephone number 3




























Telephone number 4


4


5
Telephone number 5
















6
Telephone number 6
















7
Telephone number 7
















8
Telephone number 8
















= Default
PCS GSM/GPRS Communicator Module
Use the following section to program the PCS GSM/GPRS Communicator Module on your EVO system. Use worksheets 29 to 38 to record your settings.
WinLoad/PCS Module Connection
Worksheet 29: WinLoad/PCS Module Connection Settings
Section Data
Description
[2960] ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/
Access point name (APN) part 1 (e.g., internet.com)
[2961] ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/
Access point name (APN) part 2 (e.g., wap.provider.com)
[2962] ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/
User name part 1
[2963] ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/
User name part 2
[2964] ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/
Password part 1
[2965] ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/
Password part 2
[2966] ___/___/___/___/___
Port (default = 10000)
[3013] ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/
Installer software password (WinLoad) (default = admin)
PCS Module Programming
Table 30: Section [2950] GSM Options
Description
(GSM Reporting)
Option
Option
Description
1
2
Primary
Backup
3&4
Future use
OFF
OFF
Landline
Landline
7
Future use
OFF
ON
Landline
GSM
8
ON
OFF
GSM
Landline
ON
ON
GSM
GSM
5
OFF
 Disabled
ON
 Enabled
GSM RF jamming supervision
= Default
Description
(GSM/GPRS No Service Trouble Feedback)
6
OFF
OFF
Disabled
ON
OFF
When disarmed: trouble only; when armed: trouble only
OFF
ON
When disarmed: trouble only; when armed: audible only
ON
ON
Silent alarm becomes audible alarm
PCS Module (GSM) Programming
Worksheet 30: PCS Module (GSM) Settings
Section
Data
Default: 00
Description
[2951]
___/___
[2952]
___/___/___
(000 to 255) x 2 seconds
GSM no service timer (default: 016)
[2953]
___/___/___
(000 to 255)
SMS language (default: 000)
42 | PCS GSM/GPRS Communicator Module
Panel supervision lost (reporting code)
Version 2.1
Digiplex EVO • Programming Guide
Table 31: SMS Language ID
ID
Language
ID
Language
006
ID
Language
ID
012
Croatian
018
German
013
Greek
019
Chinese
Turkish
014
Hebrew
020
Serbian
015
Russian
021 to 255
016
Bulgarian
000
English
Portuguese
001
French
007
002
Spanish
008
003
Italian
009
Hungarian
004
Swedish
010
Czech
005
Polish
011
Dutch
017
Romanian
Language
Slovak
Future use
SMS Site Name
Worksheet 31: SMS Site Name Settings
Section Label
[2954] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
IP100/PCS Module (GPRS) Options
Table 32: Section [2975] IP/GPRS Options
Option
5
6
Description
(IP No Service Trouble Feedback)
OFF
OFF
Disabled
ON
OFF
When disarmed: trouble only; when armed: trouble only
OFF
ON
When disarmed: trouble only; when armed: audible alarm
ON
ON
Silent alarm becomes audible alarm
Option
Description
7
OFF
 As IP/GPRS
reporting
backup
ON
 In addition
Use dialer reporting
to IP/GPRS
reporting
8
OFF
 Disabled
Enable IP/GPRS reporting
ON
 Enabled
IP/GPRS Reporting Account Programming
Worksheet 32: IP Account Number Settings
Section Data
Description
[2976] ___/___/___/___
IP account partition 1/account 1 number
[2977] ___/___/___/___
IP account partition 2/account 2 number
[2978] ___/___/___/___
IP account partition 3/account 3 number
[2979] ___/___/___/___
IP account partition 4/account 4 number
[2980] ___/___/___/___
IP account partition 5/account 5 number
[2981] ___/___/___/___
IP account partition 6/account 6 number
[2982] ___/___/___/___
IP account partition 7/account 7 number
[2983] ___/___/___/___
IP account partition 8/account 8 number
Worksheet 33: IP Receiver 1 Configuration
Section Data
Description
___/___/___ . ___/___/___ . ___/___/___ . ___/___/___
___/___/___/___/___
[2984] ___/___/___ . ___/___/___ . ___/___/___ . ___/___/___
___/___/___/___/___
___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___
___/___
WAN1 IP address (e.g., 100.100.100.100); for one or two-digit numbers, add 0s
before the first digit
WAN1 IP port (default: 10000)
WAN2 IP address
WAN2 IP port
IP password (e.g., 123456)
IP profile (e.g., 01)
[2985] To register IP/GPRS module, press ARM
Version 2.1
PCS GSM/GPRS Communicator Module | 43
Digiplex EVO • Programming Guide
Worksheet 34: IP Receiver 2 Configuration
Section Data
Description
___/___/___ . ___/___/___ . ___/___/___ . ___/___/___
___/___/___/___/___
[2986] ___/___/___ . ___/___/___ . ___/___/___ . ___/___/___
___/___/___/___/___
___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___
___/___
WAN1 IP address (e.g., 100.100.100.100); for one or two-digit numbers, add 0s
before the first digit
WAN1 IP port (default: 10000)
WAN2 IP address
WAN2 IP port
IP password (e.g., 123456)
IP profile (e.g., 01)
[2987] To register IP/GPRS module, press ARM
Worksheet 35: IP Receiver 3 Configuration
Section Data
Description
___/___/___ . ___/___/___ . ___/___/___ . ___/___/___
___/___/___/___/___
[2988] ___/___/___ . ___/___/___ . ___/___/___ . ___/___/___
___/___/___/___/___
___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___
___/___
WAN1 IP address (e.g., 100.100.100.100); for one or two-digit numbers, add 0s
before the first digit
WAN1 IP port (default: 10000)
WAN2 IP address
WAN2 IP port
IP password (e.g., 123456)
IP profile (e.g., 01)
[2989] To register IP/GPRS module, press ARM
Worksheet 36: IP Receiver 4 Configuration
Section Data
Description
___/___/___ . ___/___/___ . ___/___/___ . ___/___/___
___/___/___/___/___
[2990] ___/___/___ . ___/___/___ . ___/___/___ . ___/___/___
___/___/___/___/___
___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___
___/___
WAN1 IP address (e.g., 100.100.100.100); for one or two-digit numbers, add 0s
before the first digit
WAN1 IP port (default: 10000)
WAN2 IP address
WAN2 IP port
IP password (e.g., 123456)
IP profile (e.g., 01)
[2991] To register IP/GPRS module, press ARM
IP100/PCS Module Report Code Programming
Worksheet 37: PCS Module Report Codes
Section
[2967]
[2968]
[2969]
[2970]
Data
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
Description
Missing GSM module
Missing GSM module restore
Future use
Future use
GSM RF jam
GSM RF jam restore
GSM no service
GSM no service restore
Fail to communicate IPR512 1
Fail to communicate IPR512 1 restore
Fail to communicate IPR512 2
Fail to communicate IPR512 2 restore
Fail to communicate IPR512 3
Fail to communicate IPR512 3 restore
Fail to communicate IPR512 4
Fail to communicate IPR512 4 restore
Worksheet 38: IP100 Report Codes
Section
[2992]
[2993]
[2994]
Data
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
Description
Missing IP module
Missing IP Restore
IP no service
IP no service restore
Fail to communicate IPR512 1
Fail to communicate IPR512 1 restore
Fail to communicate IPR512 2
Fail to communicate IPR512 2 restore
Fail to communicate IPR512 3
Fail to communicate IPR512 3 restore
Fail to communicate IPR512 4
Fail to communicate IPR512 4 restore
44 | PCS GSM/GPRS Communicator Module
Version 2.1
Digiplex EVO Programming Guide • Partition Settings
Partition Settings
Use the following section to program the various partitions on your EVO system. Use worksheet 39 to 45 to record your settings.
Worksheet 39: Partition Label Settings for Sections [3100] to [3800]
Section Partition Label
Partition #
[3100] ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___
1
[3200] ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___
2
[3300] ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___
3
[3400] ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___
4
[3500] ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___
5
[3600] ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___
6
[3700] ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___
7
[3800] ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___
8
Auto-arm Times
Worksheet 40: Auto-arm Time Settings
Section
Data (Hours 00-23; Minutes (00-59)
Partition #
Section
Data (Hours 00-23; Minutes (00-59)
Partition #
[3101]
___/___ : ___/___
1
[3501]
___/___ : ___/___
5
[3201]
___/___ : ___/___
2
[3601]
___/___ : ___/___
6
[3301]
___/___ : ___/___
3
[3701]
___/___ : ___/___
7
[3401]
___/___ : ___/___
4
[3801]
___/___ : ___/___
8
Arming/Disarming Report Schedules
Worksheet 41: Arming Report Schedule Settings
Section Partition # Schedule
Partition Label Settings for Sections [3100] to [3800] | 45
[3102]
1
001
[3202]
2
002
[3302]
3
003
[3402]
4
004
[3502]
5
005
[3602]
6
006
[3702]
7
007
[3802]
8
008
Start Time
(From)
Interval
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
End Time
(To)
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
S
M
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Days of the Week (Turn ON or OFF)
T
W
T
F
S
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
H
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
NOTE: If a partition is armed outside a schedule, the panel will send an Early to Close [3916] and/or Late to Close [3917] report code (see worksheet 46 on page 51).
46 | Disarming Report Schedule Settings
Worksheet 42: Disarming Report Schedule Settings
Section Partition # Schedule
[3103]
1
001
[3203]
2
002
[3303]
3
003
[3403]
4
004
[3503]
5
005
[3603]
6
006
[3703]
7
007
[3803]
8
008
Start Time
(From)
Interval
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
End Time
(To)
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
S
M
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Days of the Week (Turn ON or OFF)
T
W
T
F
S
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
H
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
NOTE: If partition is disarmed outside schedule, panel will send an Early to Open [3926] and/or Late to Open [3927] report code (see worksheet 46 on page 51).
Partition Timers
Worksheet 43: Partition Timer Settings
Description
(Decimal Values from 000 to 255)
Digiplex EVO Programming Guide • Partition Settings
Arming/disarming schedule tolerance window
(Data x 1 min.; default: 000)
Number of invalid codes before lockout
(Data x 1 attempt; default: 005)
Keypad lockout duration
(Data x 1 min.; Report only: 000; Default: 015)
No movement timer
(Data x 5 min.; Default: disabled)
Exit delay timer
(Data x 1 sec.; Default: 060 sec.)
Recent closing delay
(Data x 1 sec.; Default: disabled)
Intellizone delay
(Data x 1 sec.; default: 032 sec.)
Entry delay 1
(Data x 1 sec.; default: 030 sec.)
Entry delay 2
(Data x 1 sec.; Default: 060 sec.)
Bell cut-off timer
(Data x 1 min.; Default: 4 min.)
Auto zone shutdown
(000 to 015 alarms; default: disabled)
Maximum number of zones that can be bypassed
(Data x 1 zone; Default: unlimited)
Recycle delay
(Data x 1 min.; Default: disabled)
Number of recycles
(Data x 1 attempt; Default: unlimited)
Police code timer
(Data x 1 min.; Default: disabled)
Closing delinquency timer
(Data x 1 day; Default: disabled)
Postpone auto-arm delay
(Data x 15 min.; Default: 0)
Partition 1
Section
Data
Partition 2
Section
Data
Partition 3
Section
Data
Partition 4
Section
Data
Partition 5
Section
Data
Partition 6
Section
Data
Partition 7
Section
Data
Partition 8
Section
Data
[3104] __/__/__ [3204] __/__/__ [3304] __/__/__ [3404] __/__/__ [3504] __/__/__ [3604] __/__/__ [3704] __/__/__ [3804] __/__/__
[3105] __/__/__ [3205] __/__/__ [3305] __/__/__ [3405] __/__/__ [3505] __/__/__ [3605] __/__/__ [3705] __/__/__ [3805] __/__/__
[3106] __/__/__ [3206] __/__/__ [3306] __/__/__ [3406] __/__/__ [3506] __/__/__ [3606] __/__/__ [3706] __/__/__ [3806] __/__/__
[3107] __/__/__ [3207] __/__/__ [3307] __/__/__ [3407] __/__/__ [3507] __/__/__ [3607] __/__/__ [3707] __/__/__ [3807] __/__/__
[3108] __/__/__ [3208] __/__/__ [3308] __/__/__ [3408] __/__/__ [3508] __/__/__ [3608] __/__/__ [3708] __/__/__ [3808] __/__/__
[3109] __/__/__ [3209] __/__/__ [3309] __/__/__ [3409] __/__/__ [3509] __/__/__ [3609] __/__/__ [3709] __/__/__ [3809] __/__/__
[3110] __/__/__ [3210] __/__/__ [3310] __/__/__ [3410] __/__/__ [3510] __/__/__ [3610] __/__/__ [3710] __/__/__ [3810] __/__/__
[3111] __/__/__ [3211] __/__/__ [3311] __/__/__ [3411] __/__/__ [3511] __/__/__ [3611] __/__/__ [3711] __/__/__ [3811] __/__/__
[3112] __/__/__ [3212] __/__/__ [3312] __/__/__ [3412] __/__/__ [3512] __/__/__ [3612] __/__/__ [3712] __/__/__ [3812] __/__/__
[3113] __/__/__ [3213] __/__/__ [3313] __/__/__ [3413] __/__/__ [3513] __/__/__ [3613] __/__/__ [3713] __/__/__ [3813] __/__/__
[3114] __/__/__ [3214] __/__/__ [3314] __/__/__ [3414] __/__/__ [3514] __/__/__ [3614] __/__/__ [3714] __/__/__ [3814] __/__/__
[3115] __/__/__ [3215] __/__/__ [3315] __/__/__ [3415] __/__/__ [3515] __/__/__ [3615] __/__/__ [3715] __/__/__ [3815] __/__/__
[3116] __/__/__ [3216] __/__/__ [3316] __/__/__ [3416] __/__/__ [3516] __/__/__ [3616] __/__/__ [3716] __/__/__ [3816] __/__/__
[3117] __/__/__ [3217] __/__/__ [3317] __/__/__ [3417] __/__/__ [3517] __/__/__ [3617] __/__/__ [3717] __/__/__ [3817] __/__/__
[3118] __/__/__ [3218] __/__/__ [3318] __/__/__ [3418] __/__/__ [3518] __/__/__ [3618] __/__/__ [3718] __/__/__ [3818] __/__/__
[3119] __/__/__ [3219] __/__/__ [3319] __/__/__ [3419] __/__/__ [3519] __/__/__ [3619] __/__/__ [3719] __/__/__ [3819] __/__/__
[3120] __/__/__ [3220] __/__/__ [3320] __/__/__ [3420] __/__/__ [3520] __/__/__ [3620] __/__/__ [3720] __/__/__ [3820] __/__/__
Table 33: Description of sections [3121] to [3821]
Option Description
ON
Section
Option Description
OFF
ON
Disabled

Enabled
1
Arm/disarm with partition 1

Disabled

Enabled
2
Arm/disarm with partition 2

Disabled

Enabled
2
Switch to Stay arm (if no delay zone is opened) 
Disabled

Enabled
3
Arm/disarm with partition 3

Disabled

Enabled
3
Arm/disarm with partition 3

Disabled

Enabled
4
Arm/disarm with partition 4

Disabled

Enabled
4
Arm/disarm with partition 4

Disabled

Enabled
5
Arm/disarm with partition 5

Disabled

Enabled
5
Arm/disarm with partition 5

Disabled

Enabled
6
Arm/disarm with partition 6

Disabled

Enabled
6
Arm/disarm with partition 6

Disabled

Enabled
7
Arm/disarm with partition 7

Disabled

Enabled
7
Arm/disarm with partition 7

Disabled

Enabled
Section [3221]
Partition 2
Switch to Stay arm (if no delay zone is opened) 
Arm/disarm with partition 8

Disabled

Enabled
8
Arm/disarm with partition 8

Disabled

Enabled
Arm/disarm with partition 1

Disabled

Enabled
1
Arm/disarm with partition 1

Disabled

Enabled
2
Arm/disarm with partition 2

Disabled

Enabled
2
Arm/disarm with partition 2

Disabled

Enabled
3
Switch to Stay arm (if no delay zone is opened) 
Disabled

Enabled
3
Arm/disarm with partition 3

Disabled

Enabled
4
Arm/disarm with partition 4

Disabled

Enabled
4
Switch to Stay arm (if no delay zone is opened) 
Disabled

Enabled
5
Arm/disarm with partition 5

Disabled

Enabled
5
Arm/disarm with partition 5

Disabled

Enabled
6
Arm/disarm with partition 6

Disabled

Enabled
6
Arm/disarm with partition 6

Disabled

Enabled
7
Arm/disarm with partition 7

Disabled

Enabled
7
Arm/disarm with partition 7

Disabled

Enabled
Section [3421]
Partition 4
8
1
8
Arm/disarm with partition 8

Disabled

Enabled
8
Arm/disarm with partition 8

Disabled

Enabled
1
Arm/disarm with partition 1

Disabled

Enabled
1
Arm/disarm with partition 1

Disabled

Enabled
2
Arm/disarm with partition 2

Disabled

Enabled
2
Arm/disarm with partition 2

Disabled

Enabled
3
Arm/disarm with partition 3

Disabled

Enabled
3
Arm/disarm with partition 3

Disabled

Enabled
4
Arm/disarm with partition 4

Disabled

Enabled
4
Arm/disarm with partition 4

Disabled

Enabled
5
Switch to Stay arm (if no delay zone is opened) 
Disabled

Enabled
5
Arm/disarm with partition 5

Disabled

Enabled
6
Arm/disarm with partition 6

Disabled

Enabled
6
Switch to Stay arm (if no delay zone is opened) 
Disabled

Enabled
7
Arm/disarm with partition 7

Disabled

Enabled
7
Arm/disarm with partition 7

Disabled

Enabled
Section [3621]
Partition 6
Section [3521]
Partition 5
Section [3721]
Partition 7
Partition Timer Settings | 47
= Default
OFF
1
8
Arm/disarm with partition 8

Disabled

Enabled
8
Arm/disarm with partition 8

Disabled

Enabled
1
Arm/disarm with partition 1

Disabled

Enabled
1
Arm/disarm with partition 1

Disabled

Enabled
2
Arm/disarm with partition 2

Disabled

Enabled
2
Arm/disarm with partition 2

Disabled

Enabled
3
Arm/disarm with partition 3

Disabled

Enabled
3
Arm/disarm with partition 3

Disabled

Enabled
4
Arm/disarm with partition 4

Disabled

Enabled
4
Arm/disarm with partition 4

Disabled

Enabled
5
Arm/disarm with partition 5

Disabled

Enabled
5
Arm/disarm with partition 5

Disabled

Enabled
6
Arm/disarm with partition 6

Disabled

Enabled
6
Arm/disarm with partition 6

Disabled

Enabled
7
Switch to Stay arm (if no delay zone is opened) 
Disabled

Enabled
7
Arm/disarm with partition 7

Disabled

Enabled
8
Arm/disarm with partition 8

Disabled

Enabled
8
Switch to Stay arm (if no delay zone is opened) 
Disabled

Enabled
Section [3821]
Partition 8
Section [3121]
Partition 1
Section
Section [3321]
Partition 3
Digiplex EVO Programming Guide • Partition Settings
Partition Options 1
48 | Partition Timer Settings
Partition Arming/Disarming Options
Table 34: Description of partition arming/disarming options
Option
Partition 1
[3122]
Description
OFF
1
Timed auto-arming

2
No Movement auto-arming

3
Arming method for auto arm (OFF = Force arming; ON = Stay arming)

4
Exit delay termination
5
Future use
6
Future use
7
Future use
8
Follow zone switches to Entry Delay 2, when delay zone is bypassed
ON



Partition 2
[3222]
OFF



ON



Partition 3
[3322]
OFF



ON



Partition 4
[3422]
OFF



ON



Partition 5
[3522]
OFF



OFF



Partition 6
[3622]
ON



ON



Partition 7
[3722]
ON



ON



Partition 8
[3822]
ON



ON



















-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
















= Default
Partition Panic Alarm Options
Table 35: Description of partition panic alarm options
Option
Partition 1
[3123]
Description
OFF
1
Panic 1 (K641/641R: keys 1 & 3; K656: [
])

2
Panic 2 (K641/641R: keys 4 & 6; K656: [
])

3
Panic 3 (K641/K641R: keys 7 & 9; K656: [
4
Panic 1 alarm type (OFF = report only; ON = audible alarm)

5
Panic 2 alarm type (OFF = report only; ON = audible alarm)

6
Panic 3 alarm type (OFF = report only; ON = fire alarm)

7
Always report disarming (OFF = always; ON = only after alarm)

8
Auto-force on regular arming

])

ON








Partition 2
[3223]
OFF








ON








Partition 3
[3323]
OFF








ON








Partition 4
[3423]
OFF








ON








Partition 5
[3523]
OFF








OFF








Partition 6
[3623]
ON








ON








Partition 7
[3723]
ON








ON








Partition 8
[3823]
ON








ON








= Default
Partition Bell Squawk Options
Table 36: Description of partition bell squawk options
Option
Description
Partition 1
[3124]
Digiplex EVO Programming Guide • Partition Settings
OFF
1
Bell squawk upon disarming

2
Bell squawk upon arming

3
Bell squawk upon auto-arming

4
Bell squawk during exit delay

5
Bell squawk during entry delay

6
Bell squawk upon remote arming/disarming

7
Ring back: bell squawk if disarmed after alarm

8
Ring back: keypad beeps if disarmed after alarm
= Default

ON








Partition 2
[3224]
OFF








ON








Partition 3
[3324]
OFF








ON








Partition 4
[3424]
OFF








ON








Partition 5
[3524]
OFF








OFF








Partition 6
[3624]
ON








ON








Partition 7
[3724]
ON








ON








Partition 8
[3824]
ON








ON








Digiplex EVO Programming Guide • Partition Settings
Partition One-touch Options
Table 37: Description of partition one-touch options
Option
Description
Partition 1
[3125]
OFF
1
One-touch regular arming

2
One-touch Stay arming

3
One-touch Instant arming

4
One-touch Force arming

5
One-touch Stay or Instant disarming

6
One-touch bypass programming

7
One-touch event display

8
No exit delay when arming with remote control

ON








Partition 2
[3225]
OFF








ON








Partition 3
[3325]
OFF








ON








Partition 4
[3425]
OFF








ON








Partition 5
[3525]
OFF








OFF








Partition 6
[3625]
ON








ON








Partition 7
[3725]
ON








ON








Partition 8
[3825]
ON








ON








= Default
WARNING: If a keypad is assigned to more than one partition, the one-touch feature must be enabled in all the keypad’s assigned partitions. For instance, to enable the one-touch Regular Arming feature of
a keypad assigned to partitions 1, 2, and 5, enable option 1 of sections [3125], [3225], and [3525].
Partition Special Options
Table 38: Description of partition special options
Option
Description
Partition 1
[3126]
OFF

ON

1
Intellizone delay
2
Intellizone double knockout and zone crossing
3
Intellizone zone crossing

4
Auto-force on Stay arming

5
Police code is generated on zone crossing only


6
Future use
7
Future use
8
Future use
-
-




Partition 2
[3226]
OFF




ON






-
-
Partition 3
[3326]
OFF




ON






-
-
Partition 4
[3426]
OFF




ON






-
-
Partition 5
[3526]
OFF




OFF






-
-
Partition 6
[3626]
ON




ON






-
-
Partition 7
[3726]
ON




ON






-
-
Partition 8
[3826]
ON




ON






-
-
= Default
Partition Arming/Disarming Event Call Direction
Table 39: Description of partition arming/disarming event call direction
Option
Description
Partition 1
[3127]
OFF
Partition Timer Settings | 49
1
Call telephone number 1/IP receiver 1

2
Call telephone number 2/IP receiver 2

3
Call telephone number 3/IP receiver 3

4
Call telephone number 4/IP receiver 4

5
Backup on telephone number 1/IP receiver 1

6
Backup on telephone number 2/IP receiver 2

7
Backup on telephone number 3/IP receiver 3

8
Backup on telephone number 4/IP receiver 4

= Default
NOTE: Enable only one option from options 5 to 8 (inclusive).
ON








Partition 2
[3227]
OFF








ON








Partition 3
[3327]
OFF








ON








Partition 4
[3427]
OFF








ON








Partition 5
[3527]
OFF








OFF








Partition 6
[3627]
ON








ON








Partition 7
[3727]
ON








ON








Partition 8
[3827]
ON








ON








50 | Special Arming Exit Delay Settings
Partition Alarm/Alarm Restore Event Call Direction
Table 40: Description of partition alarm/alarm restore event call direction
Option
Partition 1
[3128]
Description
OFF
1
Call telephone number 1/IP receiver 1

2
Call telephone number 2/IP receiver 2

3
Call telephone number 3/IP receiver 3

4
Call telephone number 4/IP receiver 4

5
Backup on telephone number 1/IP receiver 1

6
Backup on telephone number 2/IP receiver 2

7
Backup on telephone number 3/IP receiver 3

8
Backup on telephone number 4/IP receiver 4

ON








Partition 2
[3228]
OFF








ON








Partition 3
[3328]
OFF








ON








Partition 4
[3428]
OFF








ON








Partition 5
[3528]
OFF








OFF








Partition 6
[3628]
ON








ON








Partition 7
[3728]
ON








ON








Partition 8
[3828]
ON








ON








= Default
NOTE: Enable only one option from options 5 to 8 (inclusive).
Partition Tamper/Tamper Restore Event Call Direction
Table 41: Description of partition tamper/tamper restore event call direction
Option
Partition 1
[3129]
Description
OFF
1
Call telephone number 1/IP receiver 1

2
Call telephone number 2/IP receiver 2

3
Call telephone number 3/IP receiver 3

4
Call telephone number 4/IP receiver 4

5
Backup on telephone number 1/IP receiver 1

6
Backup on telephone number 2/IP receiver 2

7
Backup on telephone number 3/IP receiver 3

8
Backup on telephone number 4/IP receiver 4

ON








Partition 2
[3229]
OFF








ON








Partition 3
[3329]
OFF








ON








Partition 4
[3429]
OFF








ON








Partition 5
[3529]
OFF








OFF








Partition 6
[3629]
ON








ON








Partition 7
[3729]
ON








ON








Partition 8
[3829]
ON








ON








= Default
NOTE: Enable only one option from options 5 to 8 (inclusive).
Special Arming Exit Delay
Digiplex EVO Programming Guide • Partition Settings
Worksheet 44: Special Arming Exit Delay Settings
Description
(Decimal Values from 000 to 255)
Partition 1
Section
Data
Partition 2
Section
Data
Partition 3
Section
Data
Partition 4
Section
Data
Partition 5
Section
Data
Partition 6
Section
Data
Partition 7
Section
Data
Partition 8
Section
Data
Exit delay for special arming; auto arm, WinLoad/
NEWare arming, etc.)
(Data x 1 sec.; default: 060)
[3130] __/__/__ [3230] __/__/__ [3330] __/__/__ [3430] __/__/__ [3530] __/__/__ [3630] __/__/__ [3730] __/__/__ [3830] __/__/__
Digiplex EVO • Programming Guide
No Movement Schedule
Worksheet 45: No Movement Schedule Settings
Section Partition #
[3131]
1
[3231]
2
[3331]
3
[3431]
4
[3531]
5
[3631]
6
[3731]
7
[3831]
8
Start Time
(From)
Interval
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
Schedule A
Schedule B
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
End Time
(To)
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
S
M
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Days of the Week (Turn ON or OFF)
T
W
T
F
S
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
H
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
WARNING: The Start and End Time of a schedule cannot cross over into another day. For example, to program a shift from 10 PM to 6 AM the next morning,
you must program the schedule as follows: Schedule A – start time: 22:00 and end time: 23:59; then program Schedule B – start time: 00:00 and
end time: 06:00. The schedule will not be interrupted between 23:59 and 00:00.
Special and Trouble Report Codes
Use the following section to program the special and trouble report codes on your EVO system. Use worksheet 46, as well as worksheet 47 on page 52 to record your
settings.
For Ademco Slow, Silent Knight Fast, Sescoa, Ademco Express, or pager formats, key-in desired two-digit hex value from 00 to FF.
Ademco Format
•
•
Use section [4034] (Special System Report Codes), [4035] (Special Arming/Disarming Report Codes), [4036] (Special Alarm Report Codes), and [4037] (Trouble/
Trouble Restore Report Codes) to program a set of default Ademco report codes, using table 44 (Description of the automatic report codes), on page 53.
To program the remaining report codes or change certain defaults, access the individual sections and key-in the desired two-digit hex value, found in table 48
(List of Ademco contact ID report codes), on page 58.
SIA Format
•
•
•
Use section [4034] (Special System Report Codes), [4035] (Special Arming/Disarming Report Codes), [4036] (Special Alarm Report Codes), and [4037] (Trouble/
Trouble Restore Report Codes) to program a set of SIA report codes, using table 44 (Description of the automatic report codes), on page 53.
Codes that have not been set to default can be set as such manually, by entering FF in the appropriate section.
To disable the reporting of an event, enter 00 in the appropriate section.
Special Report Codes
Worksheet 46: Special Report Code Settings
Data
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
Version 2.1
Description
Power up after total power down
Software reset (watchdog)
Test report
Listen-in to follow (request to start session)
WinLoad login request (callback only)
WinLoad log off
Installer in
Installer out
Future use
Future use
Auto-arming
PC arming
Late to close (Auto-arming)
No movement
Partial arming
Quick arming
Early to close (see worksheet 41 on page 45)
Late to close (see worksheet 41 on page 45)
Remote arming (ADM2, LSN4)
Close delinquency
Type
Special Disarming
Report Codes
Section
[3900]
[3901]
[3902]
[3903]
[3904]
[3905]
[3906]
[3907]
[3908]
[3909]
[3910]
[3911]
[3912]
[3913]
[3914]
[3915]
[3916]
[3917]
[3918]
[3919]
Special Alarm
Report Codes
Special Arming
Report Codes
Special System
Report Codes
Type
Section
Data
[3920]
[3921]
[3922]
[3923]
[3924]
[3925]
[3926]
[3927]
[3928]
[3929]
[3930]
[3931]
[3932]
[3933]
[3934]
[3935]
[3936]
[3937]
[3938]
[3939]
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
Description
Cancel auto-arm
Quick disarm
PC disarming
PC disarming after alarm
Cancel alarm
Future use
Early to open (see worksheet 42 on page 46)
Late to open (see worksheet 42 on page 46)
Remote disarming (ADM2, LSN4)
Future use
Emergency panic
Auxiliary panic
Fire panic
Recent closing
Police code
Zone shutdown
Duress
Keypad lockout
Voice lockout
Future use
Special and Trouble Report Codes | 51
Digiplex EVO • Programming Guide
Trouble Report Codes
Section
Data
[3940]
[3941]
[3942]
[3943]
[3944]
[3945]
[3946]
[3947]
[3948]
[3949]
[3950]
[3951]
[3952]
[3953]
[3954]
[3955]
[3956]
[3957]
[3958]
[3959]
[3960]
[3961]
[3962]
[3963]
[3964]
[3965]
[3966]
[3967]
[3968]
[3969]
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
Description
Future use
AC failure
Battery failure
Auxiliary supply
Bell output (disconnected or overload)
Clock loss
Fire loop trouble
Future use
Future use
Future use
Combus fault
Module tamper
ROM check error
Module TLM
Module failure to communicate
Printer fault
Module AC failure
Module battery failure
Module auxiliary failure
Future use
Wireless transmitter battery low
Wireless transmitter supervision trouble
Future use
Future use
Future use
Phone number 1 fail to communicate
Phone number 2 fail to communicate
Phone number 3 fail to communicate
Phone number 4 fail to communicate
Future use
Type
Section
Data
Trouble Restore
Report Codes
Type
Trouble
Report Codes
Worksheet 47: Trouble Report Code Settings
[3970]
[3971]
[3972]
[3973]
[3974]
[3975]
[3976]
[3977]
[3978]
[3979]
[3980]
[3981]
[3982]
[3983]
[3984]
[3985]
[3986]
[3987]
[3988]
[3989]
[3990]
[3991]
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
Description
TLM1 restore
AC failure restore
Battery failure restore
Auxiliary supply restore
Bell output (reconnected or restored)
Clock loss restore
Fire loop trouble restore
Future use
Future use
Future use
Combus fault restore
Module tamper restore
ROM check error restore
Module TLM restore
Module failure to communicate restore
Printer fault restore
Module AC failure restore
Module battery failure restore
Module auxiliary failure restore
Future use
Wireless transmitter battery low restore
Wireless transmitter supervision trouble restore
Additional Settings and Modes
The following section provides information on various other settings and modes applicable to your EVO system.
Table 42: Description of sections [4000] to [4006]
Section Name
Description
[4000]
Display serial number of
control panel and all modules
connected to the combus
After entering section [4000], the keypad will display the eight-digit serial number of the control panel and firmware
version. For Keypads K641/K641R and K656: use the  and  keys to scroll through the serial number of each module
connected to the combus. The firmware version of some modules will also be displayed. For Grafica Keypads: press the
center action key (Next) to scroll through the serial number of each module on the combus.
[4001]
Module reset
Reset a module’s programmed contents to its default settings, by entering its serial number.
[4002]
Locate/unlocate module
Locate a specific module (e.g., detector, zone expander, etc.) connected to the combus, by entering the module's serial
number. The green Locate LED on the module will flash until the serial number is re-entered, or the appropriate Tamper
or Unlocate switch is pressed on the module.
[4003]
Module programming mode
Enter the serial number of the module you wish to program.
Module broadcast
Copy the contents of all programming sections from one module, to one or more modules of the same type.
Enter the serial number of the source module, followed by the serial numbers of the modules you wish to program. To
begin transferring data, press ACC on the K641/K641R keypads, on the K656 keypad, or the center action key (Start)
on Grafica keypads.
Label broadcast
Copy user, door, and partition labels from the control panel, to all keypads and printer modules connected to the
combus. To transmit the labels, enter 0 0 in section [4004]. From the Destination screen, press ACC on the K641/K641R
keypads, on the K656 keypad, or the center action key (Start) on Grafica keypads.
[4005]
Quick module scanning
After entering the section, the control panel will scan all addresses assigned to the modules. If any missing modules are
detected (i.e., detector removed from the combus), the control panel will erase the module's serial number, thus
removing the module from the control panel's memory.
[4006]
Module scanning
After entering the section, the control panel will scan all addresses on the combus. If any missing modules are detected
(i.e., detector removed from the combus), the control panel will erase the module's serial number, thus removing the
module from the control panel's memory. If new modules are detected, the serial number will be entered in the control
panel’s memory.
[4004]
WARNING: The module and label broadcast features will only work when a module is broadcasting its data to a module, or to modules of the same type
and model number.
52 | Additional Settings and Modes
Version 2.1
Digiplex EVO • Programming Guide
Paradox PMC5 Memory Key
Table 43: Description of the Paradox PMC5 memory key sections
Section Description
[4010]
Download from the memory key to the control panel, except zone numbering and sections [0501] to [0532].
[4011]
Download from the memory key to the control panel, including zone numbering and sections [0501] to [0532].
[4012]
Download user labels from the memory key to the control panel.
[4013]
Download installer default (used when resetting from memory key to control panel).
[4020]
Copy the control panel sections to the memory key, except zone numbering and sections [0501] to [0532].
[4021]
Copy the control panel sections to the memory key, including zone numbering and sections [0501] to [0532].
[4022]
Copy the control panel user label to the memory key.
[4023]
Copy the control panel installer default to the memory key.
WARNING: When using the PMC3 Memory Key, sections [4010], [4011], [4020] and [4021] will not include the labels. When using a PMC4 or PMC5, use
sections [4012] and [4022] to transfer labels.
Figure 3: The PMC5 Memory Key.
Locked: Overwriting content is not permitted
Unlocked: Copying and downloading content is permitted
Downloading Content from Memory Key to Control Panel
To download content from the memory key to the control panel, proceed as follows:
1.
Connect the memory key (PMC5) to the connector labelled MEM KEY on the control panel.
2.
To download the contents of the memory key, except zone numbering and sections [0501] to [0532], enter programming mode, and then access section
[4010]. Depending on the memory key, the labels may or may not be included.
3.
To download the contents of the memory key, including zone numbering and sections [0501] to [0532], enter programming mode, and then access section
[4011]. Depending on the memory key, the labels may or may not be included.
4.
After the keypad emits a confirmation beep, remove the memory key.
Copy Content from Control Panel to Memory Key
To copy content from the control panel to the memory key, proceed as follows:
1.
Connect the memory key (PMC5) to the connector labelled MEM KEY on the control panel. Ensure that the write-protect jumper on the memory key is ON.
2.
To copy the contents to the memory key, except zone numbering and sections [0501] to [0532], enter programming mode, and then access section [4020].
Depending on the memory key, the labels may or may not be included.
3.
To copy the contents to the memory key, including zone numbering and sections [0501] to [0532], enter section [4021]. Depending on the memory key, the
labels may or may not be included.
4.
After the keypad emits a confirmation beep, remove the memory key. Remove the memory key’s jumper, so you do not accidentally overwrite its contents.
WARNING: When using the PMC3 Memory Key, sections [4010], [4011], [4020] and [4021] will not include the labels. When using a PMC4 or PMC5, use
sections [4012] and [4022] to transfer labels.
Automatic Report Code Programming
When using contact ID or SIA Reporting formats (see worksheet 25 on page 40), default report codes can be programmed automatically. After automatic defaults
are set, they can be changed and the remaining report codes can be set manually.
Table 44: Description of the automatic report codes
Section Report Code
Description
[4030]
All report codes reset to 00
Resets all codes from sections [0201] - [0296], [0701] - [0832], [2001] - [2199], and [3900] - [3999], to 00;
sections [4031] to [4037] reset all the report codes in the following sections, to their default values which
appear in table 47 (List of automatic report codes), on page 55
[4031]
All report codes reset to FF
[0201] to [0296], [0701] to [0832], [2001] to [2199], and [3900] to [3999]
[4032]
Zone alarm/alarm restore and zone
tamper/tamper restore
[0201] to [0296]
[4033]
User/keyswitch arming and disarming
[0701] to [0832] and [2001] to [2199]
[4034]
Special report codes
[3900] to [3909]
[4035]
Special arming/disarming report codes
[3910] to [3929]
[4036]
Special alarm report codes
[3930] to [3939]
[4037]
Trouble and trouble restore report codes
[3940] to [3999]
Version 2.1
Additional Settings and Modes | 53
Digiplex EVO • Programming Guide
Software Reset
To set specific software parameters back to their initial, default values, proceed as follows:
1.
Enter programming mode (see Entering Programming Mode on page 3 for details).
2.
Enter section [4049] to unlock the software reset function.
3.
Enter the four-digit section corresponding to the software reset you wish to perform.
If you want to reset more than one section, enter section [4049] to unlock the software reset function once again.
Table 45: Description of software reset sections ([4040] to [4049])
Section Description
[4040]
Entering this section will reset all programmable sections, from [0001] to [3999], to their factory default values.
[4041]
Entering this section will reset the system master code to 123456.
[4042]
Entering this section will reset all zone programming, including sections [0961] to [0984], to their default values.
[4043]
Entering this section will reset all access control sections, from [2201] to [2712] (excluding door labels), to their default values.
[4044]
Entering this section will reset all user code sections, from [1001] to [1999] and [2001] to [2199], to their default values.
[4045]
Entering this section will reset programming of all dialer sections ([3051] to [3081]), VDMP3 sections ([3087] to [3098]), and control panel sections
([3020] to [3043] and [3900] to [3991]), to their default values.
[4046]
Entering this section will reset all partition sections, from [3101] to [3833] (excluding partition labels), to their default values.
[4047]
Entering this section will reset programming of all PGM sections ([0901] to [0959]) and all keyswitch sections ([0501] to [0632]), as well as all keyswitch
arming/disarming report code sections ([0701] to [0832]), to their default values.
[4048]
Entering this section will clear all user labels, door labels, partition labels, module labels, and zone labels, from sections [0301] to [0396].
[4049]
Entering this section will unlock software reset for sections [4040] to [4048].
Installer Function Keys
To access the installer functions, press and hold 0, enter the installer code, and then:
•
For keypads K641/K641R and K656: press the key indicated in table 46, that corresponds to the function you wish to activate.
•
For Grafica keypads: press the center action key (Options), highlight the desired function, and then press the center action key (Ok).
Table 46: Description of installer functions for the K641/K641R and K656 keypads
Function
Description
Test report
Sends the Test Report report code programmed in section [3902], to the monitoring station.
Call WinLoad software
Will dial the PC telephone number programmed in section [3010], to initiate communication with a
computer using the WinLoad software.
Answer WinLoad software
Will force the control panel to answer a call made by the monitoring station, which is using the
WinLoad software.
Cancel communication
Cancels all communication with the WinLoad software or with the monitoring station, until the next
reportable event.
Installer test mode
This mode allows you to perform walk tests, where the bell or siren will squawk to indicate opened
zones.
To exit, press MEM (for K641/K641R) or (for K656). Partitions cannot be armed if the installer test
mode is enabled.
MEM
Start module scan
The keypad will display the serial number of each module on the combus.
TRBL
Combus voltmeter
To verify if the combus is supplying sufficient power, press and hold 0, enter the installer code, and
press either ACC or , depending on the type of keypad. A reading of 12.3V or lower, at the panel’s
service keypad connector, indicates that the voltage is too low. The voltage may drop during the
control panel battery test.
ACC
54 | Additional Settings and Modes
K641/K641R
K656
STAY
STAY
FORCE
SLEEP
ARM
ARM
DISARM
OFF
Version 2.1
Digiplex EVO • Programming Guide
Automatic Report Codes
Table 47: List of automatic report codes
System Event
Default Contact ID Report Code
(when using sections [4032] to [4037])
Default SIA Report Code
(when using sections [4032] to [4037])
Arming with master code (##)
3 4A1
Close by user
CL
Closing report
Arming with user code (##)
3 4A1
Close by user
CL
Closing report
Arming with keyswitch (##)
3 4A9
Keyswitch close
CS
Closing keyswitch
Auto arming
3 4A3
Automatic close
CA
Automatic closing
Arm with PC software
3 4A7
Remote arm/disarm
CQ
Remote arming
Late to close
3 452
Late to close
OT
Late to close
No movement
3 452
Late to close
NA
No movement arming
Partial arming
1 456
Partial arm
CG
Close area
Quick arming
3 4A8
Quick arm
CL
Closing report
Remote arm (voice)
3 4A7
Remote arm
CQ
Arm with voice module
Delinquency closing
1 654
System inactivity
CD
System inactivity
Disarm with master code (##)
1 4A1
Open by user
OP
Opening report
Disarm with user code (##)
1 4A1
Open by user
OP
Opening report
Disarm with keyswitch (##)
1 4A9
Keyswitch open
OS
Opening keyswitch
Disarm after alarm with master code (##)
1 4A1
Open by user
OP
Opening report
Disarm after alarm with user code (##)
1 4A1
Open by user
OP
Opening report
Disarm after alarm with keyswitch (##)
1 4A9
Keyswitch open
OS
Opening keyswitch
Cancel alarm with master code (##)
1 4A6
Cancel
OR
Disarm from alarm
Cancel alarm with user code (##)
1 4A6
Cancel
OR
Disarm from alarm
Cancel alarm with keyswitch (##)
1 4A6
Cancel
OS
Opening keyswitch
Auto arming cancellation
1 464
Auto-arm time extended
CE
Closing extend
Cancel alarm with PC software
1 4A6
Cancel
OR
Disarm from alarm
Voice disarm
1 4A7
Remote arm/disarm
OQ
Remote disarming
Disarm with PC software
1 4A7
Remote arm/disarm
OQ
Remote disarming
Disarm after an alarm with PC software
1 4A7
Remote arm/disarm
OQ
Remote disarming
Version 2.1
Quick disarm
1 4A8
Quick disarm
OP
Opening report
Zone Bypassed (##)
1 57A
Zone bypass
UB
Untyped zone bypass
Zone alarm (##)
1 13A
Burglary alarm
BA
Burglary alarm
Fire alarm (##)
1 11A
Fire alarm
FA
Fire alarm
Early to Disarm by User
1 451
Early to open
OK
Early to open
Late to Disarm by User
1 452
Late to open
OJ
Late to open
Zone alarm restore (##)
3 13A
Burglary alarm restore
BH
Burglary alarm restore
Fire alarm restore (##)
3 11A
Fire alarm restore
FH
Fire alarm restore
24-hr Gas alarm (##)
1 13A
Burglary alarm
GA
Gas alarm
24-hr Heat alarm (##)
1 13A
Burglary alarm
KA
Heat alarm
24-hr Water alarm (##)
1 13A
Burglary alarm
WA
Water alarm
24-hr Freeze alarm (##)
1 13A
Burglary alarm
ZA
Freeze alarm
Gas alarm restore
24-hr Gas alarm restore (##)
3 13A
Burglary alarm restore
GR
24-hr Heat alarm restore (##)
3 13A
Burglary alarm restore
KR
Heat alarm restore
24-hr Water alarm restore (##)
3 13A
Burglary alarm restore
WR
Water alarm restore
24-hr Freeze alarm restore (##)
3 13A
Burglary alarm restore
ZR
Freeze alarm restore
Panic 1: emergency
1 12A
Panic alarm
PA
Panic alarm
Panic 2: medical
1 1AA
Medical alarm
MA
Medical alarm
Panic 3: fire
1 115
Pull station
FA
Fire alarm
Recent closing
3 459
Recent close
CR
Recent closing
Burglary alarm
Police code
1 139
Burglary alarm
BM
Global zone shutdown
1 574
Group bypass
CG
Close area
Duress alarm
1 121
Duress
HA
Hold-up alarm
Additional Settings and Modes | 55
Digiplex EVO • Programming Guide
Table 47: List of automatic report codes (Continued)
System Event
Default Contact ID Report Code
(when using sections [4032] to [4037])
Default SIA Report Code
(when using sections [4032] to [4037])
Zone shutdown (##)
1 57A
Zone bypass
UB
Zone tampered (##)
1 144
Sensor tamper
TA
Untyped zone bypass
Tamper alarm
Zone tamper restore (##)
3 144
Sensor tamper restore
TR
Tamper restoral
Keypad lockout
1 421
Access denied
JA
User code tamper
AC failure
1 3A1
AC loss
AT
AC trouble
Battery failure
1 3A9
Battery test failure
YT
System battery trouble
Auxiliary supply trouble
1 3AA
System trouble
YP
Power supply trouble
Bell output current limit
1 321
Bell 1
YA
Bell fault
Bell absent
1 321
Bell 1
YA
Bell fault
Clock lost
1 626
Time/date inaccurate
JT
Time changed
Fire loop trouble
1 373
Fire trouble
FT
Fire trouble
TLM trouble restore
3 351
Telco 1 fault restore
LR
Phone line restoral
AC failure restore
3 3A1
AC loss restore
AR
AC restoral
Battery failure restore
3 3A9
Battery test restore
YR
System battery restoral
Auxiliary supply trouble restore
3 3AA
System trouble restore
YQ
Power supply restored
Bell output current limit restore
3 321
Bell 1 restore
YH
Bell restored
Bell absent restore
3 321
Bell 1 restore
YH
Bell restored
Clock programmed
3 625
Time/date reset
JT
Time changed
Fire loop trouble restore
3 373
Fire trouble restore
FJ
Fire trouble restore
Combus fault
1 333
Expansion module failure
ET
Expansion trouble
Module tamper
1 145
Expansion module tamper
TA
Tamper alarm
Module ROM_RAM_error
1 3A4
ROM checksum bad
YF
Parameter checksum fail
Module TLM trouble
1 352
Telco 2 fault
LT
Phone line trouble
Module fail to communicate to monitoring station
1 354
Fail to communicate
YC
Communication fails
Printer fault
1 336
Local printer failure
VT
Printer trouble
Module AC failure
1 3A1
AC loss
AT
AC trouble
Module battery failure
1 3A9
Battery test failure
YT
System battery trouble
Module auxiliary supply trouble
1 3AA
System trouble
YP
Power supply trouble
Combus fault restore
3 333
Expansion module failure restore
ER
Expansion restoral
Module tamper restore
3 145
Expansion module tamper restore
TR
Tamper restoral
Module ROM_RAM_error restore
3 3A4
ROM checksum bad restore
YG
Parameter changed
Phone line restoral
Module TLM restore
3 352
Telco 2 fault restore
LR
Early to arm by user
3 451
Early to close
CK
Early to close
Late to arm by user
3 452
Late to close
CJ
Late to close
Zone excluded on Force arming
1 57A
Zone bypass
XW
Zone forced
Zone went back to arm status
3 57A
Zone bypass restore
UU
Zone included
Printer fault restore
3 336
Local printer failure restore
VR
Printer restore
Module AC restore
3 3A1
AC loss restore
AR
AC restoral
Module battery restore
3 3A9
Battery test failure restore
YR
System battery restoral
Module auxiliary supply restore
3 3AA
System trouble restore
YQ
Power supply restored
Fail to communicate with monitoring station
1 354
Fail to communicate
YC
Communication fails
Module RF low battery
1 384
RF transmitter low battery
XT
Transmitter battery trouble
Module RF supervision trouble
1 381
Loss of supervision - RF
US
Untype zone supervision
Module RF battery restore
3 384
RF transmitter battery restore
XR
Transmitter battery restoral
Module RF supervision restore
3 381
Supervision restore - RF
UR
Untyped zone restoral
Cold start
1 3A8
System shutdown
RR
Power up
Warm start
1 3A5
System reset
YW
Watchdog reset
Test report engaged
1 6A2
Periodic test report
TX
Test report
Listen-in request
1 606
Listen-in to follow
LF
Listen-in to follow
56 | Additional Settings and Modes
Version 2.1
Digiplex EVO • Programming Guide
Table 47: List of automatic report codes (Continued)
System Event
Version 2.1
Default Contact ID Report Code
(when using sections [4032] to [4037])
Default SIA Report Code
(when using sections [4032] to [4037])
WinLoad login request
1 411
Call back Request
RB
Remote program begin
PC software communication finished
1 412
Successful - download access
RS
Remote program success
Installer on site
1 627
Program mode entry
LB
Local program
Installer programming finished
1 628
Program mode exit
LS
Local program success
Module fail to communicate restore
3 354
Fail to communicate restore
YK
Communication restore
Missing PCS module
1 552
Radio transmitter disabled
YS
Communication trouble
GSM RF jam
1 552
Radio transmitter disabled
YS
Communication trouble
GSM no service
1 552
Radio transmitter disabled
YS
Communication trouble
GPRS FTC IPR512
1 354
Fail to communicate
YA
Communication fails
Missing IP module
1 552
Radio transmitter disabled
YS
Communication trouble
IP no service
1 552
Radio transmitter disabled
YS
Communication trouble
Communication fails
IP100 FTC IPR512
1 354
Fail to communicate
YA
Missing PCS module restore
3 552
Radio transmitter restore
YK
Communication restore
GSM RF jam restore
3 552
Radio transmitter restore
YK
Communication restore
GPRS FTC IPR512 restore
3 354
Fail to communicate restore
YK
Communication restore
Missing IP module restore
3 552
Radio transmitter restore
YK
Communication restore
IP no service restore
3 552
Radio transmitter restore
YK
Communication restore
IP100 FTC IPR512 restore
3 354
Fail to communicate restore
YK
Communication restore
Additional Settings and Modes | 57
Digiplex EVO • Programming Guide
Contact ID Report Codes
If using the Ademco contact ID format, enter the two-digit hexadecimal value (under the column heading Value intable 48) to program the desired report codes into
sections [0201] to [0296], [0701] to [0832], [2001] to [2199], and [3900] to [3999].
01
101
Personal emergency
02
102
Fire Alarm
04
111
Smoke
05
Water Flow
06
07
114
Heat
08
115
Pull Station
09
Duct
0A
Low temperature
161
162
Value
Loss of air flow
2F
331
Polling loop open
50
Carbon monoxide detected
30
332
Polling loop short
51
333
Expansion module failure
52
163
Tank level
31
334
Repeater failure
53
200
Fire supervisory
32
335
Local printer paper out
54
336
Local printer failure
55
337
Exp. module DC low
56
338
Exp. module low batt
57
339
Exp. module reset
58
341
Exp. module tamper
59
342
Exp. module AC lost
5A
343
Exp. module self-test fail
5B
201
202
Low water pressure
Low CO2
33
34
203
Gate valve sensor
35
204
Low water level
36
205
Pump activated
37
Flame
0B
206
Pump failure
38
Near Alarm
0C
300
System trouble
39
120
Panic alarm
0D
301
AC loss
3A
121
Duress
0E
302
Low system battery
3B
122
Silent
0F
303
RAM checksum bad
3C
10
124
Duress - access granted
11
130
Duress - egress granted
Burglary
12
13
Value
System peripheral
118
Audible
CID # Reporting Code
330
117
123
Type
2E
304
ROM checksum bad
3D
305
System reset
3E
306
307
Panel program changed
Self-test failure
3F
40
4F
344
RF receiver jam detected
5C
350
Communication
5D
351
Telco fault 1
5E
352
Telco fault 2
5F
353
Long range radio
60
354
Fail to communicate
61
355
Loss of radio supervision
62
356
Loss of central polling
63
Long range radio VSWR
problem
64
65
Perimeter
14
308
System shutdown
41
132
Interior
15
309
Battery test failure
42
357
133
24-hour
16
310
Ground fault
43
370
Protection loop
134
Entry/exit
17
311
Battery missing/dead
44
371
Protection loop open
66
135
Day/night
18
312
Power supply over current
45
372
Protection loop short
67
136
Outdoor
19
313
Engineer reset
46
373
Fire trouble
68
137
Tamper
1A
320
Sounder relay
47
374
Exit error alarm
69
138
Near alarm
1B
321
Bell 1
48
375
Panic zone trouble
6A
139
Intrusion verifier
1C
376
Hold-up zone trouble
6B
140
General alarm
1D
141
Polling loop open
1E
142
Polling loop short
1F
143
Extension module failure
20
144
Sensor tamper
21
145
Expansion module tamper
22
146
Silent burglary
147
Sensor supervision failure
150
24-hour non-burglary
25
151
Gas detected
26
152
Refrigeration
27
153
Loss of heat
28
154
Water leakage
29
155
Foil break
2A
156
Day trouble
2B
157
Low bottled gas level
2C
158
High temperature
2D
58 | Additional Settings and Modes
Protection Loop Troubles
(370)
131
322
Bell 2
49
323
Alarm relay
4A
377
Swinger trouble
6C
324
Trouble relay
4B
378
Cross-zone trouble
6D
325
Reversing relay
4C
380
Sensor trouble
6E
326
Notification appliance chk. #3
4D
381
Loss of supervision - RF
6F
327
Notification appliance chk. #4
4E
382
Loss of supervision - RPM
70
383
Sensor tamper
71
23
384
RF transmitter low battery
72
24
385
Smoke detector hi sensitivity
73
386
Smoke detector low sensitivity
74
387
Intrusion detector hi
sensitivity
75
388
Intrusion detector low
sensitivity
76
389
Sensor self-test failure
77
Sensor Troubles
(380)
Panic Alarms
(120)
Combustion
159
System Troubles
(300 & 310)
Fire Alarms
(110)
113
125
Burglar Alarms
(130)
03
110
116
General Alarms
(140)
Fail to report in
CID # Reporting Code
System Peripheral Troubles
(330 & 340)
Medical alarm
Type
Table 48: List of Ademco contact ID report codes
Communication Troubles
(350 & 360)
100
112
24-hour Non-burglary
(150 & 160)
Value
Fire Supervisory
(200 & 210)
CID # Reporting Code
Sounder/Relay Troubles
(320)
Medical Alarms
(100)
Type
24-hour Non-burglary
(150 & 160) (cont.)
Table 48: List of Ademco contact ID report codes
Table 48: List of Ademco contact ID report codes
391
Sensor watch trouble
78
392
Drift compensation error
79
393
Maintenance alert
7A
Version 2.1
Digiplex EVO • Programming Guide
Table 48: List of Ademco contact ID report codes
Table 48: List of Ademco contact ID report codes
CID # Reporting Code
Access Control
(420)
Special Troubles
(450 & 460)
Type
CID # Reporting Code
Value
Type
CID # Reporting Code
Value
7B
520
Sounder/relay disabled
A9
601
Manual trigger test
BD
401
Open/close by user
7C
521
Bell 1 disable
AA
602
Periodic test report
BE
402
Group open/close
7D
522
Bell 2 disable
AB
603
Periodic RF transmission
BF
403
Automatic open/close
7E
406
Cancel
7F
407
Remote arm/disarm
80
408
Quick arm
81
409
Keyswitch open/close
82
411
Callback request made
412
Successful - download access
Alarm relay disable
AC
604
Fire test
C0
524
Trouble relay disable
AD
605
Status report to follow
C1
525
Reversing relay disable
AE
606
Listen-in to follow
C2
526
Notification appliance chk. #3
disabled
AF
607
Walk test mode
C3
B0
Periodic test - system trouble
present
C4
527
Notification appliance chk. #4
disabled
608
83
84
609
Video xmitter active
C5
531
Module added
B1
611
Point test Ok
C6
532
Module removed
B2
612
Point not tested
C7
551
Dialer disabled
B3
613
Intrusion zone walk tested
C8
614
Fire zone walk tested
C9
615
Panic zone walk tested
CA
616
Service request
CB
621
Event log reset
CC
622
Event log 50% full
CD
85
414
System shutdown
86
415
Dialer shutdown
87
Successful upload
88
421
Access denied
89
422
Access report by user
8A
423
Forced access
8B
424
Egress denied
8C
425
Egress granted
8D
552
Radio transmitter disabled
B4
Test/Misc
(600)
Unsuccessful access
523
Communication Disabled
(550 & 560)
413
Sounder Relay Disables
(520)
Open/close
416
Version 2.1
Value
400
570
Zone bypass
B5
623
Event log 90% full
CE
571
Fire bypass
B6
624
Event log overflow
CF
572
24-hour zone bypass
B7
625
Time/date reset
D0
573
Burglary bypass
B8
626
Time/date inaccurate
D1
574
Group bypass
B9
627
Program mode entry
D2
Program mode exit
D3
426
Access door propped open
8E
427
Access point door status
monitor trouble
8F
428
Access point request to exit
90
429
Access program mode entry
91
575
Swinger bypass
BA
628
Access zone shunt
BB
629
32-hour event log marker
D4
Access point bypass
BC
630
Schedule change
D5
Bypasses
(570)
Remote Access
(410)
Open/Close
(400)
Type
Table 48: List of Ademco contact ID report codes
430
Access program mode exit
92
576
431
Access threat level change
93
577
432
Access relay/trigger fail
94
631
Exception schedule change
D6
433
Access RTE shunt
95
632
Access schedule change
D7
654
System inactivity
D8
434
Access DSM shunt
96
441
Armed stay
97
442
Keyswitch armed stay
98
450
Exception open/close
99
451
Early open/close
9A
452
Late open/close
9B
453
Failed to open
9C
454
Failed to close
9D
455
Auto-arm failed
9E
456
Partial arm
9F
457
User exit error
A0
458
User on premises
A1
459
Recent close
A2
461
Wrong code entry
A3
462
Legal code entry
A4
463
Re-arm after alarm
A5
464
Auto-arm time extended
A6
465
Panic alarm reset
A7
466
Service ON/OFF premises
A8
Additional Settings and Modes | 59
Digiplex EVO • Programming Guide
Keypad Programming
Use the following section to program keypads on your EVO system. Use worksheets 48 to 50 to record your settings.
K641/K641R and K656
The keypad’s serial number can be found on the keypad’s PC board. It can also be viewed by pressing and holding 0, entering the installer code, and then accessing
section [0000]. The keypad’s firmware version is also displayed in this section.
Figure 4: The K641/K641R and K656 keypads.
K641/K641R
K656
Table 49: Description of sections [001] to [006] for the K641/K641R and K656 keypads
Section [006]
General Options 3 (K641R only)
OFF
ON
Section
1
Partition 1

Disabled

Enabled
2
Partition 2

Disabled

Enabled
3
Partition 3

Disabled

Enabled
4
Partition 4

Disabled

Enabled
5
Partition 5

Disabled

Enabled
6
Partition 6

Disabled

Enabled
7
Partition 7

Disabled

Enabled
8
Partition 8

Disabled

Enabled
1
Display code entry

Disabled

Enabled
Section [002]
Assigning Doors to Partitions
Option Description
Option Description
OFF
ON
1
Door assigned to partition 1

Disabled

Enabled
2
Door assigned to partition 2

Disabled

Enabled
3
Door assigned to partition 3

Disabled

Enabled
4
Door assigned to partition 4

Disabled

Enabled
5
Door assigned to partition 5

Disabled

Enabled
6
Door assigned to partition 6

Disabled

Enabled
7
Door assigned to partition 7

Disabled

Enabled
8
Door assigned to partition 8

Disabled

Enabled
1
Mute keypad

Disabled

Enabled
Display exit delay

Disabled

Enabled
2
Exit delay beep

Disabled

Enabled
Display entry delay

Disabled

Enabled
3
Door left open pre-arm*

Disabled

Enabled
4
Confidential mode (not for UL
installations)

Disabled

Enabled
4
Chime on zone closure

Disabled

Enabled
5
Exit confidential mode

Enter code

Press
button
5
Door left open alarm feedback*

Silent

Audible
6
Future use

-

-
6
Door left open alarm follows*

Alarm
restore

Beep timer
7
Future use

-

-
7
Door forced alarm*

Silent

Audible
8
Time display option

yy/mm/dd

dd/mm/yy
8
Door forced alarm*

Alarm
restore

Beep timer
1
System and clock trouble beep

Disabled

Enabled
1
PGM state**

N.O.

N.C.
Deactivati
on event

PGM timer
2
Communicator trouble beep

Disabled

Enabled
3
Module and combus trouble beep

Disabled

Enabled
4
All zone trouble beep

Disabled

Enabled
5
Future use

-

-
6
Future use

-

-
7
Time format

24 hr. clock

12 hr. clock
8
Audible feedback on access
request

Disabled

Enabled
1
Card activates door unlocked
schedule

Disabled

Enabled
2
Door left open alarm

Disabled

Enabled
3
Door forced open alarm

Disabled

Enabled
4
Future use

-

-
5
Keypad tamper

Disabled

Enabled
6
Re-lock door

After
opening

After
closing
7
Future use

-

-
8
Unlock on REX

Disabled

Enabled
60 | Keypad Programming
Section [004]
General Options 2
2
3
Section [006]
PGM and Tamper Options
Section [005]
Beep on Trouble
Section [003]
General Options 1
Section [001]
Keypad Partition Assignment
Section
2
PGM deactivation mode**

3
PGM base time

1 sec.

1 min.
4
PGM Override**

Disabled

Enabled
5
Keypad tamper

Disabled

Enabled
6
Future use

-

-
7
Future use

-

-
8
Future use

-

-
= Default
* Section/option is only available on K641R.
** Section/option is only available on K641 and K656.
Version 2.1
Digiplex EVO • Programming Guide
Worksheet 48: Keypad Settings for Sections [007] to [013]
Section
Data
Description
Default Setting
[007]
___/___/___
(005-255 sec.)
Confidential mode timer
120
[008]
___/___/___
(000-255; see option 3 in section [006])
PGM timer
005
[008]
___/___/___
(000-255 sec.)
Door unlocked period*
005
[009]
___/___/___
(005-255 sec. added to section [008])
Door unlocked period extension*
015
[010]
___/___/___
(000-255 sec.)
Door left open interval*
060
[011]
___/___/___
(000-255 sec.)
Door left open pre-alarm timer*
015
[012]
___/___/___
(000-255 sec.)
Beep timer for door left open alarm*
005
[013]
___/___/___
(000-255 sec.)
Beep timer for door forced open alarm*
005
* Section/option is only available on K641R.
Worksheet 49: Door Unlocked Schedule (K641R only)
Section
Interval
Start Time
(From)
End Time
(To)
S
M
[017]
Schedule A
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
___ ___ : ___ ___
___ ___ : ___ ___
1
1
2
2
Days of the Week (Turn ON or OFF)
T
W
T
F
S
3
3
4
4
5
5
6
6
7
7
H
8
8
Table 50: Description of sections [3080] to [3081]
Option Description
Section [018]
Beeping Assignment
Section
OFF
ON
1
Partition 1

Mute

Audible
2
Partition 2

Mute

Audible
3
Partition 3

Mute

Audible
4
Partition 4

Mute

Audible
5
Partition 5

Mute

Audible
6
Partition 6

Mute

Audible
7
Partition 7

Mute

Audible
8
Partition 8

Mute

Audible
= Default
Worksheet 50: PGM Activation and Deactivation
Description
Event Group
Section
Data
Feature Group
Section
Data
Section
Data
Section
Data
PGM activation
PGM deactivation
[009]
[013]
[010]
[014]
[011]
[015]
__/__/__
__/__/__
[012]
[016]
__/__/__
__/__/__
__/__/__
__/__/__
__/__/__
__/__/__
Start #
End #
WARNING: All event groups, except groups 064 to 067, can be used to program the module’s PGM. See Programmable Outputs on page 19, for details.
Label Programming
Each section, from [101] to [148], [200] to [204], and [301] to [396], contains one label with a maximum of 16 characters. These sections contain the following
labels:
•
Sections [101] to [148]: zone 01 to zone 48, respectively
•
Section [200] = Paradox security
•
Sections [201] to [204]: first area, second area, third area, and fourth area
•
Sections [301] to [396]: code 01 to code 96, respectively
After entering the section corresponding to the desired label, the label can be re-programmed to suit your installation needs (see table 51). For example, section
[101] (Zone 01) can be changed to Front Door.
Table 51: Description of the special function keys, used for programming labels on the K641/K641R and K656 keypads
Function
Description
Insert space
Insert a blank space at the current cursor’s position.
Delete
Delete the character or blank space found at the cursor’s current position.
Delete until end of entry
Delete all characters and spaces to the right of the cursor, as well as at the cursor’s current position.
Numeric/alphanumeric
Toggle from numeric to alphanumeric keys, and vice versa. Numeric: keys 0 to 9 represent numbers 0
to 9; alphanumeric: refer to table 52.
K641/K641R
K656
STAY
STAY
FORCE
SLEEP
ARM
ARM
DISARM
OFF
MENU
Lower/upper case
Toggle from lower to upper case, and vice versa.
BYP
Special characters
After pressing this key, the cursor will turn into a flashing black square. Using the special characters
outlined in figure 5, enter the three-digit number for the desired character.
MEM
Version 2.1
Keypad Programming | 61
Digiplex EVO • Programming Guide
Figure 5: Special characters for label programming.
Table 52: Description of alphanumeric key inputs
Key
Press Key
Once
Press Key
Twice
Press Key
Three Times
1
A
B
C
2
D
E
F
3
G
H
I
4
J
K
L
5
M
N
O
6
P
Q
R
7
S
T
U
8
V
W
X
9
Y
Z
Using the Memory Key
Table 53: Description of memory key sections ([510] to [520])
Section Description
[510]
Download all content from the memory key (keypad sections [001] to [396], as well all labels and messages) to the keypad.
[520]
Copy the keypad sections [001] to [396], as well as labels and messages to the memory key.
Downloading Content from Memory Key to Keypad
To download content from the memory key to the keypad (refer to figure 6), proceed as follows:
1.
Connect the memory key to the connector labelled KEY on the keypad.
2.
Enter the keypad’s programming mode, and then access section [510].
3.
Wait for two separate confirmation beeps, and then remove the memory key.
Figure 6: Downloading from memory key to keypad and vice-versa.
Downloading from memory
key to keypad
Copying from keypad to
memory key
Copying Content from Keypad to the Memory Key
To copy content from the memory key to the keypad (refer to figure 6), proceed as follows:
1.
Connect memory key to the connector labelled KEY on the keypad. Ensure that the write-protect jumper is ON (refer to figure 7).
2.
Enter the keypad’s programming mode, and then access section [520].
3.
Wait for two separate confirmation beeps, and then remove the memory key. Remove the memory key’s jumper, so you do not accidentally overwrite its contents.
Figure 7: The PMC5 Memory Key.
Locked: Overwriting content is not permitted
Unlocked: Copying and downloading content is permitted
62 | Keypad Programming
Version 2.1
Digiplex EVO • Programming Guide
Combus Voltmeter
To verify if the combus is supplying sufficient power, press and hold 0, enter the installer code, and press ACC on the K641/K641R keypads, or on the K656 keypad.
A reading of 10.5V or lower, indicates to a distant module that the voltage is too low. The voltage may drop during the control panel battery test.
Updating Firmware Using WinLoad
To update your system firmware:
1.
Connect the product to your PC, using a 307USB Direct Connect Interface or CV4USB Converter.
NOTE: If you are using the 307USB to upgrade a keypad that features a four-pin serial connector, you must first disconnect the GRN and YEL combus wires.
2.
3.
4.
5.
6.
7.
8.
Launch WinLoad.
Click the In-Field Programmer icon.
Verify the product information located in the In-Field Firmware Programmer window.
If the firmware programmer automatically detects your control panel, proceed to the next step. If it does not automatically detect your control panel, click
Com Port Settings and select the correct Com port. Once the correct port has been selected, click the Refresh Product Info button to connect with the panel.
To check for new firmware updates, click Download Firmware from the Web.
From the Select Firmware drop-down menu, select the firmware version you wish to install. If you have already downloaded the PUF file from paradox.com,
click [...], and then select your PUF file from the appropriate location.
Click Update Product Firmware. When the download process comes to an end, the update is complete.
Hardware Connections for the Control Panel
The following section provides information on certain hardware connections for your EVO 48/EVO192 control panel. For detailed information, including connection
diagrams, refer to the EVO48/EVO192 Installation Guide. The installation guide is available from paradox.com.
Milliamp Consumption
Worksheet 51: Milliamp Consumption of Various Devices
Device
QTY
Consumption for
Each
Total
(mA)
PCS Communicator Module
__________
x 600 mA
__________
Grafica graphic LCD keypads (K07)
__________
x 130 mA
__________
LCD keypads (K641, K656)
__________
x 110 mA
__________
LCD keypads with built-in reader (K641R)
__________
x 120 mA
__________
LED keypads (K648)
__________
x 110 mA
__________
Motion detector modules (DG85, DM50/60/70)
__________
x 30 mA
__________
Door contact modules (ZC1)
__________
x 15 mA
__________
1-Zone expansion modules (ZX1)
__________
x 30 mA
__________
4-Zone expansion modules (ZX4)
__________
x 30 mA
__________
8-Zone expansion modules (ZX8)
__________
x 30 mA
__________
Magellan wireless expansion modules (RTX3)
__________
x 35 mA
__________
4-PGM expansion modules (PGM4)
__________
x 150 mA
__________
Printer modules (PRT3)
__________
x 25 mA
__________
DVACS modules (DVAC)
__________
x 40 mA
__________
Annunciator modules (ANC1)
__________
x 20 mA
__________
InTouch voice-assisted arm/disarm modules (ADM2)
__________
x 105 mA
__________
Hub and bus isolator (HUB2)
__________
x 50 mA
__________
Access control module (ACM12)
(The ACM12 consumes 130mA from its own power supply and cannot be powered by the
combus; the ACM11 consumes 120mA when connected to the combus for power)
__________
x 120 mA
__________
Listen-in module (LSN4)
__________
x 60 mA
__________
Internet module (IP100)
__________
x 110 mA
__________
Plug-in voice module (VDMP3)
__________
x 35 mA
__________
PCS module
__________
x 600 mA
__________
Other devices such as hardwired motion detectors
__________
Grand Total
(The maximum available milliamps is 700 mA)
Version 2.1
__________
__________
Hardware Connections for the Control Panel | 63
Digiplex EVO • Programming Guide
Using worksheet 51 on page 63, proceed as follows:
1.
Calculate the total number of milliamps (mA) required by each device, module, and accessory in your EVO system. Make sure to take into account devices connected to the control panel’s PGM outputs. Since the bell output has its own power supply, do not include the sirens which are connected to it in your
calculation.
2.
If the grand total is less than 700 mA, proceed to step 3. If the value is greater, an external power supply will be required to provide the additional power
needed.
3.
Due to the degradation of a power signal over long distances (if such is the case, the PS17 Paradox Power Supply Module is recommended), each length (or
run) of wire in the system can support only a specific number of milliamps (mA). Using table 54, determine how many milliamps each run of wire can support.
NOTE: The total number of milliamps (mA) can never surpass 700 mA.
Table 54: Milliamp reference table for different wire gauges
Available
Milliamps (mA)
30 m (100 ft.)
Length
(of each run of wire)
Available
Milliamps (mA)
Length
(of each run of wire)
Available
Milliamps (mA)
700
30 m (100 ft.)
700
30m (100 ft.)
700
61 m (200 ft.)
700
91 m (300 ft.)
700
61 m (200 ft.)
682
61m (200 ft.)
429
91 m (300 ft.)
454
91m (300 ft.)
286
122 m (400 ft.)
152 m (500 ft.)
700
122 m (400 ft.)
341
122m (400 ft.)
214
690
152 m (500 ft.)
273
152m (500 ft.)
171
183m (600 ft.)
143
183 m (600 ft.)
575
213 m (700 ft.)
493
244 m (800 ft.)
431
274 m (900 ft.)
383
305 m (1000 ft.)
345
457 m (1500 ft.)
230
610 m (2000 ft.)
172
762 m (2500 ft.)
138
914 m (3000 ft.)
115
Wire
Gauge
183 m (600 ft.)
227
213 m (700 ft.)
195
244 m (800 ft.)
170
274 m (900 ft.)
151
305 m (1000 ft.)
136
Wire
Gauge
24 AWG
(Surface: 0.205 sq. mm)
Length
(of each run of wire)
22 AWG
(Surface: 0.326 sq. mm)
18 AWG
(Surface: 0.823 sq. mm)
Wire
Gauge
Connecting the Combus in Noisy Environments
When installing the combus wires in proximity to high electrical interference, such as neon lights, motors, high-voltage wiring, and transformers, or if connecting
the combus across separate buildings, you must use shielded cables. Connect the shielded cable as follows:
•
Within the same building: strip the outer jacket at one end of the shielded cable to expose the shield. Connect the shield to the control panel ground (not the
dialer ground), while leaving the shield at the other end of the cable open (floating).
•
Across separate buildings: strip the outer jacket at one end of the shielded cable to expose the shield. In the same building that houses the control panel,
connect the exposed shield to a cold water pipe or any other earth ground available, while leaving the shield at the other end of the cable open (floating). The
same configuration applies to any subsequent building.
Built-in RTC
Digiplex EVO panels incorporate an RTC directly on the PC board. The RTC will save the control panel’s internal clock when both the AC and battery power have
been lost. After power is lost and then restored, the control panel will verify with the RTC and retrieve the time. The control panel will then verify and compare its
time with the time stored in the RTC, every hour. If the times differ, the control panel will reset its internal clock to the time saved in the RTC. The RTC uses a 3V
lithium battery (CR2032) with a battery life of 11 years. Install the battery as shown in figure 8.
Figure 8: Changing the RTC’s lithium battery.
WARNING: When replacing the RTC’s battery, beware of the following, possible hazards:
•
•
If the lithium battery is installed incorrectly, there is the chance that it may explode. Replace only with the same or an equivalent type, recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
Do not connect a DGP2-TM1 Time Module to the MEM KEY connector. Connecting a DGP2-TM1 will create time errors within the panel, and features
that use the control panel's internal clock (e.g., auto-arming) will not function properly. In addition, re-program the control panel’s clock after
replacing the 3V lithium battery.
64 | Hardware Connections for the Control Panel
Version 2.1
Digiplex EVO • Programming Guide
Trouble Display
The following section provides information on the different trouble groups associated with your EVO 48/EVO192 control panel.
K641/K641R and K648
To view the trouble display on the K641/K641R and K648 keypads:
1.
Press TRBL.
2.
To view the specific trouble:
a.
For K648, press the numerical symbol corresponding to the Group heading.
b.
For K641/K641R, press the trouble’s corresponding number key and use the  and  keys.
K656
To view the trouble display on the K656 keypad:
1.
Press MENU.
2.
Press 5 or scroll to the View Trouble sub-menu using the  and  keys, and then press ENTER.
3.
Press the trouble’s corresponding number key and use the  and  keys to view the specific trouble.
Grafica
To view the trouble display on Grafica keypads:
1.
Enter your access code.
2.
Using the scroll keys, highlight Trouble and then press the center action key (Ok). The troubles will appear by trouble group. If more than one trouble group
appears, highlight the desired group before pressing the center action key (View), to view the specific trouble.
Trouble Groups
Table 55: Trouble groups for the EVO system
4
Bell current limit
5
Bell absent
6
ROM check error
7
RAM check error
Description
Press 5 to display the tampered
zone or zones
9: GSM Troubles
Group
Version 2.1
#
Description
1
Missing GSM module
3
GSM RF jam
supervision
4
No service
5
Fail to communicate
with IP receiver 1
Group
Group
Fail to Com. 1
3
Fail to Com. 2
4
Fail to Com. 3
5
Fail to Com. 4
6
Fail to Com. PC
Description
Press 6 to display the zone(s)
assigned to wireless devices with
low batteries
#
Description
6
Fail to communicate
with IP receiver 2
7
Fail to communicate
with IP receiver 3
8
Fail to communicate
with IP receiver 4
9
IP receiver unregistered
Group
Group
1
Module tamper
2
Module ROM check
error
3
Module TLM trouble
4
Module Fail to Com.
5
Printer trouble
6
Module AC failure
7
Module battery failure
8
Module supply output
Description
Press 7 to display the zone(s)
experiencing a communication,
a fire loop, or CleanMe™ trouble.
#
Description
1
Missing IP module
2
No service
3
Fail to communicate
with IP receiver 1
4
Fail to communicate
with IP receiver 2
Group
4: Network (Combus) Troubles
Aux. current limit
2
Description
Group
8: Clock Loss
3
TLM1
#
Group
10: IP Troubles
(cont.)
Battery trouble
1
Group
3: Module Trouble
2
Description
7: Zone Fault
AC failure
#
10: IP Troubles
1
Group
2: Communicator
Description
6: Zone Low Battery
5: Zone Tamper
Group
#
9: GSM Troubles
(cont.)
1: System
Group
#
Description
1
Missing keypad
2
Missing module
3
Missing voice module
6
General failure
7
Combus overload
Description
Press 8 to re-program the time
#
Description
5
Fail to communicate
with IP receiver 3
6
Fail to communicate
with IP receiver 4
7
IP receiver unregistered
Trouble Display | 65
Notes
The whole Paradox team wishes you a successful and easy installation. We hope this product performs to your complete satisfaction. Should you have any questions
or comments, please contact us.
For support, please contact your local distributor, or dial 1-800-791-1919 (in North America) or
+1-450-491-7444 (outside North America), Monday to Friday, from 8:00 a.m. to 8:00 p.m. EST.
You may also e-mail us at [email protected].
Additional information can be found at PARADOX.COM
Printed in Canada - 09/2010
PARADOX.COM
EVO-EP05

advertisement

Key Features

  • Program zones and keyswitches
  • Configure programmable outputs
  • Set up remote controls
  • Assign doors to the system
  • Create schedules
  • Manage access levels
  • Understand report codes
  • Troubleshoot system issues

Frequently Answers and Questions

What is the default installer code?
The default installer code is 000000.
How do I enter programming mode?
Press and hold the 0 key, enter your installer code, enter the four-digit section you want to program, and then enter the required data.
How do I reset the panel to its default settings?
Press and hold the RESET and AUX buttons for four seconds.
How do I program a zone?
Enter section [0400], enter the zone number, enter the zone's serial number and input number, enter the zone parameters, enter the report codes, and then enter the label.
What are the different zone definitions?
The zone definitions include disabled, stay, force, Intellizone, delay before transmission, and various alarm types such as pulsed, silent, report only, delayed 24-hour fire, and standard 24-hour fire.
How do I program a user code?
Enter section [0500], enter a user code number, enter the user code, and then select the user code options.

Related manuals

Download PDF

advertisement