D-Link | ShareCenter Quattro DNS-345 | - D-Link Canada

Table of Contents
Table of Contents
Introduction............................................................... 1
Before.you.Begin...................................................... 2
System.Requirements.............................................. 2
Product Overview ........................................................ 3
Package.Contents.................................................... 3
Features................................................................... 4
Checking.the.Hardware.Requirements..................... 6
Setting.Up.in.Just.a.Few.Easy.Steps....................... 8
Part I.............................................................................. 9
Hardware.Overview................................................ 10
Front.Panel....................................................... 10
Rear.Panel.(Latches)........................................ 14
Rear.Panel.(Connections)................................ 15
Getting Started........................................................... 16
Hardware.Setup...................................................... 16
D-Link.Storage.Utility.............................................. 18
Setup.Wizard.and.Storage.Utility............................ 20
Remove.the.Front.Cover.and.Install.the.Hard.
Drives................................................................ 21
Replace.the.Front.Cover.and.Connect.to.the.
Local.LAN......................................................... 22
Power.and.Device.Selection............................. 23
Admin.Password............................................... 24
Networking.Setup............................................. 25
Dynamic.DNS................................................... 26
D-Link ShareCenter Quattro DNS-345 User Manual
DDNS.Account.Setup....................................... 27
DDNS.Account.and.System.Time..................... 28
Email.Settings.and.Volume.Information............ 29
RAID.Coniguration.and.Encryption.................. 30
Mapping.a.Drive.and.Checking.Volume.
Summary.......................................................... 31
Formatting.Volumes.......................................... 32
Formatting.Hard.Drives.and.Selecting.Add-on.
Packages.......................................................... 33
Add-on.Packages............................................. 34
Wizard.Complete.............................................. 35
Mapping.a.Drive................................................ 36
Part II........................................................................... 39
Managing.your.ShareCenter.Quattro.DNS-345.40
Coniguration - Web UI Login ................................... 41
Web.UI.General.Layout.......................................... 42
Management........................................................... 45
Setup.Wizard.(Web.UI)..................................... 46
Disk.Management................................................... 51
Hard.Drive.Coniguration.................................. 51
Hard.Drive.Coniguration.Wizard...................... 52
JBOD................................................................ 59
RAID.0.............................................................. 64
RAID.1.............................................................. 69
RAID.5.............................................................. 77
i
Table of Contents
RAID.5.+.Spare................................................. 84
RAID.10............................................................ 90
A.Quick.S.M.A.R.T..Test................................... 97
Creating.a.Schedule.for.the.S.M.A.R.T.Test.... 99
Scanning.the.volumes.................................... 100
Volume.Encryption.......................................... 102
Account.Management.-.Creating.Single.Users.... 108
Account.Management.-.Creating.Multiple.Users.. 113
Account.Management.-.Creating.the.same.user.. 117
Account.Management.-.Modify.Users.................. 119
Account.Management.-.Deleting.Users................ 123
Account.Management.-.Importing.Users.............. 124
Account.Management.-.Creating.a.Group............ 127
Account.Management.-.Modifying.a.Group.......... 132
Account.Management.-.Deleting.a.Group............ 137
Quota.Settings................................................ 138
Network.Shares.............................................. 143
Adding/Modifying.New.Network.Shares.
Wizard............................................................. 144
Deleting.a.Network.Share............................... 151
Resetting.the.Network.Shares........................ 153
Adding.New.ISO.Mount.Shares.Wizard.......... 154
Admin.Password............................................. 158
Active.Directory.Settings................................. 159
Distributed.File.System................................... 160
Network.Management..................................... 165
Network.Management.-.DDNS....................... 170
Network.Management.-.UPnP.Router.
D-Link ShareCenter Quattro DNS-345 User Manual
Detection......................................................... 171
Network.Management.-.Port.Forwarding........ 173
Application.Management.-.FTP.server........... 175
UPnP.Server................................................... 179
iTunes.Server................................................. 182
Add.Ons.......................................................... 183
AFP.and.NFS.Services................................... 186
System.Management.-.Language................... 187
System.Management.-.Time.and.Date........... 188
System.Management.-.Device........................ 190
System.Management.-.System.Settings......... 191
System.Management.-.Power.Management.. 192
System.Management.-.Notiications............... 195
System.Management.-.Logs........................... 198
System.Management.-.Firmware.Upgrade..... 199
System.Management.-.SNMP........................ 200
System.Management.-.USB.Devices............. 201
System.Status.-.System.Info.......................... 203
Part III........................................................................ 205
Applications.......................................................... 206
FTP/HTTP.Downloads.................................... 206
Applications.-.FTP.Downloads........................ 211
Remote.Backups............................................ 213
Local.Backups................................................ 218
Local.Backups.-.Time.Machine....................... 219
Local.Backups.-.USB.Backups....................... 220
USB.Print.Server.................................................. 224
P2P.Downloads.-.Settings.............................. 232
ii
Table of Contents
P2P.Downloads.-.Downloads......................... 233
Web.File.Server.............................................. 234
Amazon.S3..................................................... 235
Photo.Center................................................... 236
My.Favorites......................................................... 241
Add.an.Icon.to.My.Favorites........................... 242
Removing.an.Icon.from.My.Favorites............. 243
Knowledge Base ...................................................... 244
What.is.RAID?...................................................... 244
RAID.OPTIONS.............................................. 246
RAID.Comparison.Chart................................. 249
USB.Print.Server.................................................. 250
UPS.Connectivity.................................................. 254
Deleting.a.UPS.Slave........................................... 259
Knowledge Base ...................................................... 261
What.is.Ethernet.Bonding?................................... 261
D-Link ShareCenter Quattro DNS-345 User Manual
iii
Section 1 - Product Overview
Introduction
The D-Link ShareCenter Quattro DNS-345 is a 4-Bay Network Attached Storage device, when used with internal SATA
drives1, enables you to share documents, iles, and digital media such as music, photos, and video with everyone on
the home or ofice network. Remotely accessing iles through the Internet is also possible using the built-in FTP server,
Web File server and WebDAV protocol. Whether you are allowing access locally or over the Internet, keep data safe
by only giving rights to speciic users or groups. When coniguring the DNS-345, you can create and assign users and
groups to folders with either read or read/write permissions. This is ideal for an ofice environment with employeespeciic sensitive data or for the home where you can limit your children to age appropriate material. The DNS-345 will
be available to any computer (PC, MAC, or Linux-based) on your network, without the need to install additional software.
Back up your music, photos, and video collections to the DNS-345 for safekeeping. Then, enjoy the beneits of the
built-in UPnP AV media server as you stream digital content to compatible media players2 (such as those found in
D-Link’s MediaLounge product line). This feature is very convenient as it allows you to turn off a computer that would
normally be needed for the same function.
The DNS-345 has seven RAID modes (Standard, JBOD, RAID 0, RAID 1, RAID 5, RAID 5+SPARE, & RAID 10).
y. Standard.-.creates.a.single.volume.from.one.drive..
y. JBOD.-.combines.all.drives.in.a.linear.fashion.for.maximum.space.eficiency
y. RAID.0.-.uses.all.drives.as.a.single.massive.array.of.storage.with.the.combined.capacity.of.all.the.drives
y. RAID.1.-.also.known.as.disk.mirroring,.the.system.will.save.data.to.all.the.drives.in.the.same.array.simultaneously
y. RAID.5.-.requires.at.least.3.drives..Data.is.split.into.blocks.and.stored.over.all.of.the.drives..Parity.data.is.distributed.amongst.all.of.
y.
y.
the.drives.and.is.used.to.regenerate.lost.data.during.a.drive.failure.
RAID.5+SPARE.-.data.is.a.mirrored.striped.set.with.distributed.parity..If.a.drive.in.the.array.fails,.the.hot.spare.is.used.to.rebuild.the.
array.and.restore.the.redundancy.as.soon.as.possible.
RAID.10.-.is.a.combination.of.RAID.0.(data.striping).and.RAID.1.(mirroring)..It.offers.the.highest.performance.and.data.protection.
1..Hard.Drive(s).not.included.
2..D-Link.cannot.guarantee.full.compatibility.or.proper.playback.with.all.codecs..Playback.capability.depends.on.the.codec.support.of.the.UPnP™.AV.media.player.
D-Link ShareCenter Quattro DNS-345 User Manual
1
Section 1 - Product Overview
To further enhance your ShareCenter’s capabilities you can expand the applications available with the ShareCenter
by using the Add-On feature which allows you to add supported software applications. These applications can add
over the web audio streaming, ile and media sharing, and even blogging capability to your ShareCenter..
Before you Begin
• Check box contents
• Check system requirements
• Ensure that you have the hardware you need for your ShareCenter Quattro device
System Requirements
For best results, the following minimum requirements are recommended on any system used to conigure and
use the ShareCenter™:
„ Computer with: 1Ghz processor / 512 MB RAM / 200 MB available space / CD-ROM drive
„ Internet Explorer version 7, Mozilla Firefox 3, Google Chrome 3 or Apple Safari 4 and above
„ Windows® XP (with Service Pack 2), Windows Vista™ , Windows 7™ ‘
„ Windows 2003 Server
„ Windows 2008 Server
„ Mac OS X 10.5.6 or greater
„ 3.5” SATA Hard Drive(s)
D-Link ShareCenter Quattro DNS-345 User Manual
2
Section 1 - Product Overview
Product Overview
Package Contents
„
„
„
„
„
D-Link ShareCenter™ Quattro DNS-345
CD-ROM with Manual and Software
Quick Installation Guide
Power Cord and 19VDC 4.74A Output Power Adapter
Cat5E Ethernet Cable
CDROM
Quick Installation Guide
Manual
Power Cord
D-Link ShareCenter Quattro DNS-345 User Manual
Software
Ethernet Cable
3
Section 1 - Product Overview
Features
The ShareCenter™ Quattro DNS-345 is an easy to install data storage platform used for remote access through a local network
or from the Internet. This ShareCenter™ supports up to 4 SATA hard drives and includes the product features listed below:
„
„
„
„
„
„
„
„
Four Hard Drive Bays for 3.5” SATA Hard Drives, up to
3TB HDD (or higher)
High Performance Gigabit Ethernet Connectivity
Simpliied Hard Drive Installation Process
OLED Screen - System Information/Temperature,
LAN/Volume status, USB Backups
Supports Remote File Access via Built-in Web File Server,
FTP, or WebDAV
Network Protocols
• Supports DDNS
• Supports UPnP, Bonjour
• Supports PnP-X /LLTD
• Supports VLAN (tags)
• Link Aggregation / Fail-over and Fail-back
for 2 Gigabit Ethernet ports
• Supports UPnP Port Forwarding
Network File Services
• Supports NFS/AFP Server
• Supports uni-code for both Samba and FTP server
• Supports DFS (Microsoft DFS)
Disk Management
• Seven Hard Drive Conigurations: Standard; JBOD;
RAID 0; RAID 1; RAID 5; RAID 5+spare; and RAID 10
• Supports Volume Encryption
• Supports RAID migration: Standard to RAID 1,
Standard to RAID 5, RAID 1 to RAID 5
• Supports Advanced Format HDD
D-Link ShareCenter Quattro DNS-345 User Manual
„
„
„
„
„
• HDD S.M.A.R.T Test
• Supports FAT16/32, NTFS for USB external Storage
Account Management
• Users and Groups can be assigned to Folders with
Read or Read/Write Permissions
• Quotas for Users and Groups
• Supports ISO mount Shares
• Supports Active Directory fpr Windows 2003/2008
Server
FTP Server
• Built-in FTP server for File Access over the Internet
• Supports FTP over SSL/TLS abd FXP
Download Management
• Scheduled downloads from Web or FTP sites
• Supports P2P and aMule downloads
Backup Management
• Supports Local Backup
• Full or Incremental Backup
• Real-time Backups with included Backup Software
• Supports Apple Time Machine
• Supports USB Backups
• Supports Remote Network Backup
• Supports Cloud Storage Backup (Amazon S3)
Power Management for Conserving Energy and Extending
Hard Drive life
• Supports Auto Power Recovery
• Supports Schedule Power ON/OFF
4
Section 1 - Product Overview
„
„
„
Media Streaming
UPnP AV Server for streaming music, photos, and
videos to compatible media
• iTunes software will be able to automatically ind
and play music directly from the ShareCenter Quattro
Supports Add-On Software and Multi-Language Packages
• Blogging with WordPress
• Logitech Squeeze Center
• Audio Streaming
• AjaXplorer
• Photo Station
System Management
• Web Browser coniguration
• Supports HTTPs management
• Network Recycle Bin
• Supports Yahoo Widgets
• Supports System Logging/FTP logging
• Automatic e-mail and SMS notiications
• Supports network UPS
• Supports SNMPv2
• Supports Resource Monitor
D-Link ShareCenter Quattro DNS-345 User Manual
5
Section 1 - Product Overview
Checking the Hardware Requirements
To use your ShareCenter Quattro, you will need at least one hard drive. If you plan to use RAID, which protects your
data against one hard drive failure, you will need at least two hard drives.
Note: For the ShareCenter Quattro, we recommend that you use at least four 1TB high performance drives. This
provides more data drives, better striping performance, and helps distribute loads more effectively.
This section will help you:
• Select the hard drives you will use
• Choose the amount of space to have available on those drives
• Ensure your data is protected
• Understand the basic requirements for a router or switch
Selecting Hard Drives:
You can use hard drives from any manufacturer and with any capacity with your ShareCenter Quattro. All D-Link
devices support standard 3.5” internal SATA drives. If you are unsure, ask your administrator or hard drive retailer/
manufacturer to verify that your hard drives meet this standard
Warning - Any pre-existing data on the drives will be erased during installation.
D-Link ShareCenter Quattro DNS-345 User Manual
6
Section 1 - Product Overview
Determining How Much Hard Drive Space you Need:
In order to protect your data from hard drive failure, your ShareCenter Quattro requires more space than what you will
use for your data, sometimes as much as double or more the amount of space required.
For the best results in calculating how much space is available for your data, always make sure you have more disk
space than what is necessary.
The ShareCenter Quattro DNS-345 makes it easy to increase storage capacity in the future by simply inserting
additional drives or replacing smaller drives with larger ones. This means you can buy the hard drives one day and
then easily expand another day. The DNS-345 accepts standard 3.5-inch internal SATA hard drives, regardless of
manufacturer, capacity, or speed.
For dual disk redundancy, it is recommended that you using two drives for storing data and two for redundancy.
The drives used for redundancy must have a total capacity of at least the sum of the two drives used for storing data.
Using a Router or Switch:
If you are connecting your ShareCenter Quattro to a router or switch, your router or switch needs to support Gigabit
Ethernet (1000Mbit/s) for peek performance. The ShareCenter Quattro will auto-negotiate the highest connection
speed available to your router or switch. If you are using Port Bonding, use a Managed switch.
Using an Uninterrupted Power Supply (UPS):
We highly recommend that you use your ShareCenter Quattro in conjunction with an uninterrupted power supply
(UPS), which will protect against sudden loss in power and power surges.
D-Link ShareCenter Quattro DNS-345 User Manual
7
Section 1 - Product Overview
Setting Up in Just a Few Easy Steps
Once you have unpacked your ShareCenter Quattro from its box and ensured you meet all system and hardware
requirements, it is now time to set up your DNS-345 for use. This can be done in just a few easy steps:
1.
2.
3.
4.
5.
Insert the hard drives
Connect the power and LAN cables to your ShareCenter Quattro
Power on the device
Run the D-Link ShareCenter Setup Wizard to conigure the NAS
Conigure the hard drives
D-Link ShareCenter Quattro DNS-345 User Manual
8
Section 2 - Getting Started
Part I
D-Link ShareCenter Quattro DNS-345 User Manual
9
Section 1 - Product Overview
Hardware Overview
Front Panel
}
Front Bezel
The front bezel comes off to reveal the hard disk drive rack
D-Link ShareCenter Quattro DNS-345 User Manual
10
Section 1 - Product Overview
OLED Screen
Next Button
Power Button
Drive Tray
COMPONENT
OLED.Screen
DESCRIPTION
The OLED screen displays the welcome screen, hard disk information, IP address information for
both LAN ports, irmware version, temperature, and hard drive modes.
Power.Button
Press once to power on the ShareCenter Quattro or conirm USB Backup functions. Press and hold
the button until the OLED screen displays “Shutdown System” to power it down.
Press once to scroll between various modes or cancel USB Backup functions.
With the front cover off, SATA hard drives can be slid in and out of the of ShareCenter Quattro. Use
the tabs on the rear of the ShareCenter Quattro to initially push a HDD out of its connector and tray.
Next.Button
Drive.Tray
D-Link ShareCenter Quattro DNS-345 User Manual
11
Section 1 - Product Overview
Hard Drive(s) Status:
Amber light(s) - the hard
drive(s) are present.
No amber lights - the hard
drive(s) are absent.
The IP address on LAN 1
The IP address on LAN 2
Disconnected means there
is no connection.
System Shutdown
D-Link ShareCenter Quattro DNS-345 User Manual
This
displays
the
irmware version and the
temperature in Celsius
and Fahrenheit.
This displays the drive
name
and
usable
storage capacity.
Welcome to D-Link
ShareCenter
12
Section 1 - Product Overview
Enter Backup mode
D-Link ShareCenter Quattro DNS-345 User Manual
Backup from NAS to USB
Backups are complete
13
Section 1 - Product Overview
Rear Panel (Latches)
}
Rear Hard Drive Latches
Click the rear latches to disconnect the hard drives from the SATA sockets. Note - Remove the front cover before releasing the latches.
D-Link ShareCenter Quattro DNS-345 User Manual
14
Section 1 - Product Overview
Rear Panel (Connections)
HDD Eject Lever
Cooling Fan
HDD Eject Lever
Reset Button
Power Receptacle
Gigabit Ethernet Ports
Cord Hook
HDD Eject Lever
USB Port
Cooling Fan
HDD Eject Lever
COMPONENT
Cooling.Fan
Gigabit.Ethernet.Ports
Power.Receptacle
USB.Port
Reset.Button
HDD.Eject.Lever
DESCRIPTION
The.cooling.fan.is.used.to.cool.the.hard.drives.and.features.speed.control..When.the.unit.is.irst.powered.on.
the.fans.rotate.at.a.low.speed.and.rotate.at.a.high.speed.when.the.temperature.rises.above.49.°C.
Use.the.Gigabit.Ethernet.Ports.to.connect.the.ShareCenter.Quattro.to.the.local.network..The.port.is.equipped.
with.both.a.LAN.Link/Trafic.(R).and.Speed.LED.(L).to.indicate.connectivity.and.trafic.respectively.to.the.
local.LAN..Dual.LAN’s.support.Port.Bonding.
Connect.the.supplied.power.cord.to.the.receptacle.
A.single.USB.2.0.(Type.A).connector..The.USB.Host.port.is.for.Print.Servers,.USB.memory.disks,.or.USB.
UPS.monitoring.
Press.and.hold.this.button.for.more.than.5.seconds.to.reset.the.unit.to.factory.defaults.
Use.each.slot’s.lever.to.eject.the.HDD.drive..
D-Link ShareCenter Quattro DNS-345 User Manual
15
Section 2 - Getting Started
Getting Started
Hardware Setup
This.User.Guide.will.help.you.get.your.ShareCenter.Quattro.set.up.in.just.a.few.steps..To.install.the.ShareCenter.
Quattro.on.your.local.network,.refer.to.the.steps.below:
Slide Up
Remove. the. front. panel:. Firmly. grip.
the. panel. and. slide. it. up. until. the. 4.
panel.hooks.clear.the.slot.openings.
Insert.one.3.5”.SATA.hard.drive.into.
an.available.drive.bay.
Note:.Make.sure.to.align.the.drive.connector.to.the.SATA.connector.at.the.back.edge.inside.the.drive.bay.of.the.
ShareCenter.Quattro..Gently.push.the.drive.in.until.it.connects..When.a.drive.is.inserted.properly,.you.will.feel.it.“seat”.
into.the.connector..Some.hard.drives.that.are.thin.or.oddly.shaped.may.need.to.be.guided.carefully.into.position..If.a.
drive.is.not.properly.seated,.the.hard.drive.icon.will.not.illuminate.on.the.OLED.screen.after.powering.on.the.device.
D-Link ShareCenter Quattro DNS-345 User Manual
16
Section 2 - Getting Started
Re-attach.the.front.panel..Align.the.4.
panel. hooks. with. the. corresponding.
slots.on.the.chassis.and.slide.the.front.
panel.down.until.it.is.irmly.seated.
Connect. an. Ethernet. cable. to. the..
LAN.1.Ethernet.port..This.cable.should.
connect. the. ShareCenter. Quattro.
to. your. local. network. via. a. router,.
switch,. or. directly. to. a. computer. for.
coniguration.
Connect. the. power. adapter. to. the.
power.receptacle.
D-Link ShareCenter Quattro DNS-345 User Manual
17
Section 1 - Product Overview
D-Link Storage Utility
When irst powered on, during the initial boot sequence, the ShareCenter will wait to be assiend an IP address via DHCP.
If it does not receive a DHCP assigned IP address, the ShareCenter will be automatically assigned a 169.254.xxx.xxx
address. It is recommended that you use the included D-Link Storage Utility software when accessing and coniguring
the ShareCenter for the irst time. If you want to change the IP address before logging in or you have having trouble
connecting to the ShareCenter IP address, you can then use the Storage Utility software included on the product CD
to locate the device on your network and make any necessary changes.
The D-Link Storage Utility displays any
Storage Device
Letters
ShareCenter™ devices it detects on the
network here
Click Refresh to refresh the device list
Click Coniguration to access the Web based
coniguration of the ShareCenter™
Configure the LAN Settings for the
ShareCenter™ here
Click Apply to save changes to the LAN
Settings
Click Connect to connect to the iSCSI target
Click Management to edit the information
Volumes available for mapping are displayed
here
Choose an available drive letter. Click Connect
to map the selected volume. Click Disconnect
to disconnect the selected mapped volume
Click About to view the software version of the
Easy Search Utility.
Click Exit to close the utility.
D-Link ShareCenter Quattro DNS-345 User Manual
18
Section 1 - Product Overview
Select. the. ShareCenter. from. the. list. and. click. the.
Coniguration. button.. This. will. launch. the. computer’s.
default.web.browser.and.direct.it.to.the.IP.address.listed.
for.the.device..Make.sure.the.browser.is.not.conigured.
to.use.a.proxy.server.
Note:.The.computer.used.to.access.the.ShareCenter
web-based.coniguration.manager.must.be.on.the.same.
subnet. as.the.ShareCenter.. If.your. network. is. using. a.
DHCP.server.and.the.computer.receives.IP.settings.from.
DHCP.server,.the.ShareCenter.will.automatically.be.in.
the.same.subnet.
D-Link ShareCenter Quattro DNS-345 User Manual
19
Section 2 - Getting Started
Setup Wizard and Storage Utility
The ShareCenter Setup Wizard is the companion software to your DNS-345, enabling you to easily set up and manage
your ShareCenter Quattro. You can now install the ShareCenter Setup wizard from the resource CD that came with
your product.
To run the Setup Wizard, insert the ShareCenter Quattro CD into your CD-ROM drive:
Click.Setup.Wizard.Utility
The.Setup.Wizard.will.step.you.through.the.
coniguration. of. getting. your. ShareCenter.
Quattro.ready.for.immediate.use..Select.the.
Language.of.your.choice.and.click.the.Start.
button.
D-Link ShareCenter Quattro DNS-345 User Manual
20
Section 2 - Getting Started
Remove the Front Cover and Install the Hard Drives
Follow.the.instructions.to.remove.the.front.
cover.of.your.ShareCenter.Quattro.
Click.Next.to.continue.
Follow.the.instructions.to.slide.either.one.or.
two.hard.drive(s).into.an.available.hard.drive.
bay.of.your.ShareCenter.
Click.Next.to.continue.
D-Link ShareCenter Quattro DNS-345 User Manual
21
Section 2 - Getting Started
Replace the Front Cover and Connect to the Local LAN.
With.the.hard.drives.installed.properly.into.
each. bay,. close. the. chassis. by. sliding. the.
panel.down.into.place.
Click.Next.to.continue.
D-Link ShareCenter Quattro DNS-345 User Manual
Connect.a.Cat5E.Ethernet.cable.with.RJ-45.
connectors.to.your.ShareCenter.and.connect.
the. other. end. to. a. switch. or. router. (Local.
LAN).
Click.Next.to.continue.
22
Section 2 - Getting Started
Power and Device Selection
Connect. the. power. adapter. connector.
to. the. power. receptacle. at. the. back. of.
the. ShareCenter.. Then. power. on. the.
ShareCenter™.by.pressing.the.power.button.
located..under.the.OLED.screen.
With. the. power. on,. press. the. Next. button.
on.the.device.and.check.and.make.sure.the.
IP. address. of. your. ShareCenter. Quattro.
matches.what.you.see.on.the.screen.
Click.Next.to.continue.
Click.Next.to.continue.
D-Link ShareCenter Quattro DNS-345 User Manual
23
Section 2 - Getting Started
Admin Password
Enter.the.administrator.password..If.this.is.
the.irst.time.you.are.doing.the.installation.on.
this.NAS,.leave.the.password.blank.
Click.Next.to.continue.
D-Link ShareCenter Quattro DNS-345 User Manual
In.this.step.you.can.create.a.new.password.
for.the.‘Admin”.username..It.is.recommended.
you.set.a.password,.however.you.may.also.
leave.the.ields.blank.
Click.Next.to.continue.
24
Section 2 - Getting Started
Networking Setup
You. may. either. use. Static. IP. or. DHCP. to.
conigure.the.irst.IP.network.settings.of.the.
ShareCenter.. If. you. select. Static. IP. then.
enter.the.IP.parameters.as.listed.
You. may. either. use. Static. IP. or. DHCP. to.
conigure.the.second.IP.network.settings.of.
the.ShareCenter..If.you.select.Static.IP.then.
enter.the.IP.parameters.as.listed.
Click.Next.to.continue.
Click.Next.to.continue.
D-Link ShareCenter Quattro DNS-345 User Manual
25
Section 2 - Getting Started
Dynamic DNS
If.you.want.your.ShareCenter.to.be.part.of.
a. Windows. Workgroup. network,. enter. the.
workgroup. name,. a. name. for. the. device,.
and. a. description.. The. name. you. entered.
will.be.used.whenever.you.map.one.of.the.
ShareCenter™.volumes.as.a.Network.Drive.
Click.Next.to.continue.
D-Link ShareCenter Quattro DNS-345 User Manual
Click. the. ‘Yes’. radio. button. if. you. already.
have. a. DDNS. account. to. use. for. the.
ShareCenter.Quattro.DDNS..Click.the.‘No’.
radio.button.and.proceed.to.step.16.to.obtain.
a.new.DDNS.account.
Click.Next.to.continue.
26
Section 2 - Getting Started
DDNS Account Setup
Enter. the. DDNS. parameters. requested. in.
this.window.so.that.your.ShareCenter.can.
be.accessed.by.a.URL.over.the.Internet.
Click.Yes.to.go.to.a.Wizard.with.instructions.
and. links. on. how. to. obtain. a. free. DDNS.
account..
Click.Next.to.continue.
Click. No. skips. the. DDNS. account. setup.
wizard. and. transfers. you. back. to. the.
ShareCenter.Setup.Wizard.
D-Link ShareCenter Quattro DNS-345 User Manual
27
Section 2 - Getting Started
DDNS Account and System Time
Follow.the.steps.listed.here.in.order.to.create.
a. DDNS. account. and. conigure. your. LAN.
equipment. and. ShareCenter. to. work. with.
the.new.settings.
Click.Close.to.continue.
D-Link ShareCenter Quattro DNS-345 User Manual
Select. the. ShareCenter. system. time. date.
and.timezone.settings.using.this.step..You.
can.set.the.time.and.date.manually,.from.an.
NTP.server,.or.from.the.computers.settings..
The.timezone.is.set.manually.
Click.Next.to.continue.
28
Section 2 - Getting Started
Email Settings and Volume Information
Configure. an. e-mail. service. with. the.
ShareCenter. to. receive. e-mail. events. to.
alert.users.of.any.changes.to.the.system.
You. must. have. all. mail. server. information.
nearby.or.contact.your.systems.administrator.
for.assistance.
This.step.shows.the.conigured.Volumes.set.
up.on.the.ShareCenter.Quattro.
Click.Next.to.continue.
Click.Next.to.continue.
D-Link ShareCenter Quattro DNS-345 User Manual
29
Section 2 - Getting Started
RAID Coniguration and Encryption
Select. one. of. the. 4. Volume. File. Systems.
desired.. Clicking. on. each. ile. system. type.
radio.button.will.give.a.description.if.needed..
For.more.information.concerning.the.different.
RAID.Disk.Formats.please.refer.to.the.user.
manual.
Once.the.RAID.coniguration.is.complete,.the.
ShareCenter.Quattro.prompts.you.to.encrypt.
each.or.all.drives..Check.the.box.next.to.the.
hard.drive(s).you.wish.to.encrypt.
Click.Next.to.continue.
Click.Next.to.continue.
D-Link ShareCenter Quattro DNS-345 User Manual
30
Section 2 - Getting Started
Mapping a Drive and Checking Volume Summary
This.step.allows.you.to.map.the.volume(s).
created.as.network.drive(s).on.your
computer.
Click.Next.to.continue.
Review.the.detailed.summary.of.your.volume.
coniguration.here.before.clicking.next.and.
starting.the.drive.format..If.necessary.use.the.
PREV.button.to.go.back.and.reconigure.the.
RAID.comiguration.of.the.volume(s).
Click.Next.to.continue.
D-Link ShareCenter Quattro DNS-345 User Manual
31
Section 2 - Getting Started
Formatting Volumes
When. you. click. Next,. a. warning. message.
will.appear.to.inform.you.that.all.data.on.the.
drive(s).will.be.lost..Click.Yes.to.proceed.or.
No.to.exit.
Click.Next.to.continue.
During. the. format. process. the. wizard.
displays.a.percentage.complete.bar.for.each
hard.drive.
Click.Next.to.continue.
D-Link ShareCenter Quattro DNS-345 User Manual
32
Section 2 - Getting Started
Formatting Hard Drives and Selecting Add-on Packages
The.wizard.will.notify.you.when.formatting.is.
complete.successfully.
Click.Next.to.continue.
Your. ShareCenter. supports. Add-On.
packages.. Here. you. may. install. the. Audio.
Streamer,. Blog,. SqueezeCenter,. Photo.
Center,. aMule,. and. AjaXplorer. add-ons.
which.extend.the.application.functionality.of.
your.ShareCenter.Quattro.
Click.Next.to.continue.
D-Link ShareCenter Quattro DNS-345 User Manual
33
Section 2 - Getting Started
Add-on Packages
The. wizard. will. notify. you. that. the. Add-on.
packages.are.installed.successfully.
The. next. screen. allows. you. to. enable. or.
disable.the.installed.add-on.packages.
Click.Next.to.continue.
Click.Next.to.continue.
D-Link ShareCenter Quattro DNS-345 User Manual
34
Section 2 - Getting Started
Wizard Complete
our ShareCenter Quattro is now installed and ready
to use. If your drives are mapped using the wizard, you
will be able to access them under your ‘My Computer’
icon.
If you did not use the wizard to map the drives, you
can manually map or access the created volumes
through your computers operating system. Detailed
conigurations using the Web UI is explained in the
coniguration section of this manual.
The.ShareCenter.Setup.Wizard.is.complete..
Click.Finish.to.exit.the.wizard.and.start.using.
your.DNS-345.NAS.
Click.Next.to.continue.
D-Link ShareCenter Quattro DNS-345 User Manual
35
Section 2 - Getting Started
Mapping a Drive
!" ! #$%&' () *)+$ ,-. +/%01 2%0#)3/ 4 () !55'// %( (6$)+16 2%0#)3/ 78"9)$'$.
Click. Start,. then. Computer. (the. name. of.
your.computer)..
This.screen.shows.some.details.on.selecting.
a.network.drive.
On.the.right-side.panel.is.a.list.of.your.hard.
drives,. removable. storage. ,. and. network.
locations.. If. you. do. not. have. any. network.
locations,.this.may.be.the.irst.time.you.set.
up.a.network.drive..Begin.by.clicking.on.‘Map
network drive’.
Click.Browse.to.ind.your.network.
D-Link ShareCenter Quattro DNS-345 User Manual
36
Section 2 - Getting Started
Windows.will.automatically.detect.all.devices.
on.your.network.including.your.DNS-345.
D-Link ShareCenter Quattro DNS-345 User Manual
Click.on.your.NAS.to.see.the.volumes.you.
created. earlier.. Then. select.the. volume.
that.you.wish.to.access.and.click.OK.
37
Section 2 - Getting Started
After. selecting. your. volume,. click. Finish
proceed.
D-Link ShareCenter Quattro DNS-345 User Manual
The.drive.will.then.appear.in.your.Windows.
Explorer. in. green.. This. means. the. drive. is.
active.and.ready.for.use..
38
Section 2 - Getting Started
Part II
D-Link ShareCenter Quattro DNS-345 User Manual
39
Section 1 - Product Overview
Managing your ShareCenter Quattro DNS-345
ShareCenter Quattro is the key interface in managing your DNS-345. IT is a browser-based utility that allows you to
manage and conigure the different tools and services available. ShareCenter is divided into three main sections.
1. Management
2. Applications
3. My Favorites
These sections are divided into the essential features of the ShareCenter Quattro.
SECTION
Management
FEATURE
Setup.Wizard
System.Status
DESCRIPTION
Step by step guide through password & time settings, connectivity, and device
coniguration
Conigures disk volumes, RAID, and performs disk diagnostics
Conigures. user. and. group. management,. network. shares,. active. directory.
paths,.and.distributed.ile.systems
Conigures LAN, Dynamic DNS, and Port Forwarding
Conigures.FTP,.UPnP,.iTunes.server.conigurations,.Add-ons,.AFP,.and.NFS.
services
Conigures.language,.time.and.date,.device,.and.system.settings..Also.allows.
you.to.control.power,.notiications,.view.logs,.do.irmware.upgrades,.SNMP.
checks.and.manage.USB.devices.
Displays.system.and.hard.drive.information.along.with.resource.monitoring
FEATURE
FTP/HTTP.Downloads
Remote.Backup
Local.Backups
DESCRIPTION
Conigure FTP and HTTP download settings
Conigure remote backup services
Conigures local backups, Time Machine© settings, and USB backups
P2P.Downloads
Web.File.Server
Amazon.S3
Conigure your P2P downloads and control your download schedules
Create,.conigure,.and.manage.your.web.ile.server.settings
Create,.modify,.and.delete.your.Amazon.S3©.settings
Disk.Management
Account.Management
Network.Management
Application.Management
System.Management
SECTION
Applications
D-Link ShareCenter Quattro DNS-345 User Manual
40
Section 4 - Coniguration
Coniguration - Web UI Login
To manage and access your ShareCenter Quattro DNS-345, open a web browser from our Systems Requirements
list, type in the IP address of your NAS, and login. When you were coniguring your DNS-345, you set up your LAN
settings. Under these settings you will ind your IP address. Enter the IP address into your browser to navigate to the
ShareCenter login page.
The following Login screen will appear:
Select System Administrator
and enter the password set using
the Setup Wizard.
Note: The computer, used to access the ShareCenter
web-based coniguration, manager must be on the same
subnet as the ShareCenter. Quattro. If your network
is using a DHCP server and the computer receives
IP settings from the DHCP, the ShareCenter™ will
automatically be in the same subnet.
D-Link ShareCenter Quattro DNS-345 User Manual
Click Login.
41
Section 4 - Coniguration
Web UI General Layout
After logging in, the ShareCenter web UI will navigate you to the ‘My Favorites’ tab by default. You will see the Applications
and Management tabs alongside of it. You will ind the coniguration icons in the Management tab.
}
The My
Favorites
screen
D-Link ShareCenter Quattro DNS-345 User Manual
42
Section 4 - Coniguration
}
The
Applications
screen
D-Link ShareCenter Quattro DNS-345 User Manual
43
Section 4 - Coniguration
}
The
Management
screen
D-Link ShareCenter Quattro DNS-345 User Manual
44
Section 4 - Coniguration
Management
:;< =>?>@<A<?B B>C DE?B>F?G B;< H<BIJ KFL>MNO PFGQ =>?>@<A<?BO RDDEI?B =>?>@<A<?BO S<BTEMQ =>?>@<A<?BO RJJUFD>BFE? =>?>@<A<?BO HVGB<A =>?>@<A<?BO >?N
Status icons. Click on each of the icons to see the submenus.
D-Link ShareCenter Quattro DNS-345 User Manual
45
Section 4 - Coniguration
Setup Wizard (Web UI)
The ShareCenter Quattro has a System Wizard that allows you to quickly conigure some of the basic device settings. Click the System Wizard icon to start the Setup Wizard.
Click the Run Wizard button to start the setup
wizard.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
46
Section 4 - Coniguration
Update the administrator account password here
and conirm the password or leave it blank.
Click Next to continue.
Set the timezone to the appropriate geographical zone
closest to your location from the drop-down menu.
Click Next to continue.
Click Skip to ignore these settings.
D-Link ShareCenter Quattro DNS-345 User Manual
47
Section 4 - Coniguration
The ShareCenter LAN 1 parameters can either use
DHCP to obtain its IP settings dynamically or Static
to set them manually in the parameters below.
Click Skip to ignore these settings.
Click Next to continue.
The ShareCenter LAN 2 parameters can either use
DHCP to obtain its IP settings dynamically or Static
to set them manually in the parameters below.
Click Skip to ignore these settings.
D-Link ShareCenter Quattro DNS-345 User Manual
48
Section 4 - Coniguration
Here you can assign a workgroup and name to
the ShareCenter in addition to a short description.
Click Next to continue.
Click Skip to ignore these settings.
Click Account to enter your e-mail address in
the boxes below. The e-mail account will then
receive Event Alerts from the ShareCenter. Click
Anonymous to create a random account with no
speciic settings.
Click Skip to ignore these settings.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
49
Section 4 - Coniguration
Click Finish to continue.
Click the Previous button to go back and heck your
settings. If you are satisied with the settings, click
the Finish button to save and continue. Click Exit
to end the wizard without saving the settings.
D-Link ShareCenter Quattro DNS-345 User Manual
50
Section 4 - Coniguration
Disk Management
Hard Drive Coniguration
Wo setup the Hard Drive RAID coniguration of your ShareCenter, click on the Management tab and then the Disk Management icon. Select the Hard Drive Coniguration
menu item on the left of the window. This menu will allow you to set the RAID type and format your hard drives.
XYZ[ \Z]^_ ˆour ShareCenter hard drives can be conigured and
Coniguration
formatted in various RAID conigurations here.
`aZZ_bc dY][ ef ghi jklmin oki opkiojq frksoggij ghi tuev wrxyz{koglrx |lpp
Type
be displayed here.
}_c d~\ €plw rx ghln ‚{ggrx gr po{xwh o |lƒokj ghog oppr|n qr{ gr
type and ReFormat
select the RAID coniguration and format the drives.
~ac„…d_†a]‡[ ef qr{ homi whrnix tuev ‰Š‹ on ghi wrxyz{koglrx rŒglrx
Coniguration
ŽbY†‡_
AutoRebuild
\]Y†‡_
AutoRebuild
then set the Auto-Rebuild function here using the radio
buttons.
xo‚plxz u{grŠti‚{lpj |lpp ki‚{lpj o folpij tuev ‰Š‹ jklmi
when a new drive has replaced the degraded one.
ef qr{ jr xrg |oxg gr o{grsoglwoppq ki‚{lpj jklmin ofgik o
failure when using the RAID 1-5 functionality then you can
check this option.
Note: You can still rebuild a drive using the RAID 1-5
functionality however you must initiate the rebuild
manually.
‘YbaY‡ ef u{grŠti‚{lpj ln jlno‚pij ghix qr{ wox {ni ghi ’ox{op
Rebuild Now
Rebuild option by clicking this button.
D-Link ShareCenter Quattro DNS-345 User Manual
51
Section 4 - Coniguration
Hard Drive Coniguration Wizard
“”•– —˜™ š›œš ˜– ž”• Ÿ •ž ¡¢£¤ ž—¥• ¦–§ ¡•¨©˜ª«¦ž¬ ­™žž˜– œ– ž”• ¤œ® ¯¦–¦°•«•–ž¨±¦ª§ ¤ªœ²• ³˜–´°™ª¦žœ˜– «•–™ ¦ µœ¶¦ª§ µœ›› ®ž¦ªž· ¦››˜µœ–° —˜™ ž˜ ¸˜ª«¦ž —˜™ª §ªœ²•®
and create the volume RAID format. The following is an example of a standard volume coniguration:
The ‘Hard Drive Configuration’ page shows
the current RAID configuration under
‘Current RAID Type’.
The options below provide other choices.
1. Set RAID type and Re-Format
2. Conigure Newly Inserted Hard Drive(s)
Click ‘Set RAID Type and Re-Format’
D-Link ShareCenter Quattro DNS-345 User Manual
52
Section 4 - Coniguration
The ‘Physical Disk Information’ page displays all
of the hard drives on the DNS-345. It shows the
array number, vendor, model, serial number, and
drive capacity.
Click Next to continue.
The ‘Select a RAID Type’ page gives you six
different RAID options to configure your hard
drives. Select the type you wish to use.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
53
Section 4 - Coniguration
Select Standard to create separate volumes for
each individual drive.
Click Next to continue.
Choose a volume or volumes that you would like
to encrypt.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
54
Section 4 - Coniguration
Select Auto Mount if you wish to mount the
drive(s) without entering a password every time.
Enter the encryption password and enter it again
to conirm.
Click Next to continue.
The ‘Volume Configuration Summary’ shows
details on all of the conigured drives. Check the
details on the list and click Format to continue or
click Previous to make changes.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
55
Section 4 - Coniguration
A warning message will appear to inform you that
all volumes and data will be formatted and erased.
Click Next to continue.
Partitioning will now begin. Please be patient while
this process takes place. Do not turn off your NAS
during this process.
D-Link ShareCenter Quattro DNS-345 User Manual
56
Section 4 - Coniguration
Once the partition is completed, the format process
will begin. A graphical bar will show the volume
being formatted. Please be patient during this
process. Do not turn off your NAS during this
process.
If you would like to change your settings at this
stage, click Exit.
The system will now update all of the changes
made.
Please be patient during this process. Do not turn
off your NAS during this process.
D-Link ShareCenter Quattro DNS-345 User Manual
57
Section 4 - Coniguration
The wizard is now complete. It will show the volume
number(s), ile system selected, the type of RAID,
and the disk formation in the RAID.
Click Finish to complete the process and start using
your DNS-345.
D-Link ShareCenter Quattro DNS-345 User Manual
58
Section 4 - Coniguration
JBOD
Select JBOD to create a single volume from all of
the drives.
Click Next to continue.
Choose a volume or volumes that you would like
to encrypt.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
59
Section 4 - Coniguration
If you decided not to encrypt the volume, a volume
coniguration summary page will show the details
of your coniguration.
Click Format to continue or Previous make
changes.
If you are encrypting the volume, select Auto Mount,
enter a password, and conirm the password.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
60
Section 4 - Coniguration
The ‘Volume Configuration Summary’ shows
details on all of the conigured drives. Check the
details on the list and click Format to continue or
click Previous to make changes.
ShareCenter will now prepare the volume for
partitioning.
D-Link ShareCenter Quattro DNS-345 User Manual
61
Section 4 - Coniguration
A warning message will appear to inform you that
all volumes and data will be formatted and erased.
Click Next to continue.
Once the partition is completed, the format process
will begin. A graphical bar will show the volume
being formatted. Please be patient during this
process. Do not turn off your NAS during this
process.
If you would like to change your settings at this
stage, click Exit.
D-Link ShareCenter Quattro DNS-345 User Manual
62
Section 4 - Coniguration
The system will now update all of the changes
made.
Please be patient during this process. Do not turn
off your NAS during this process.
The wizard is now complete. It will show the volume
number(s), ile system selected, the type of RAID,
and the disk formation in the RAID.
Click Finish to complete the process and start using
your DNS-345.
D-Link ShareCenter Quattro DNS-345 User Manual
63
Section 4 - Coniguration
RAID 0
Select RAID 0 to mirror all of the drives
Click Next to continue.
Select a capacity for RAID 0 (in GB) then check the
box next to ‘Conigure the remaining disk space
as JBOD’ if you wish to conigure the remaining
space as JBOD.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
64
Section 4 - Coniguration
Choose a volume or volumes that you would like
to encrypt.
Click Next to continue.
The ‘Volume Configuration Summary’ shows
details on all of the conigured drives. Check the
details on the list and click Format to continue or
click Previous to make changes.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
65
Section 4 - Coniguration
A warning message will appear to inform you that
all volumes and data will be formatted and erased.
Click Next to continue.
Partitioning will now begin. Please be patient while
this process takes place. Do not turn off your NAS
during this process.
D-Link ShareCenter Quattro DNS-345 User Manual
66
Section 4 - Coniguration
Once the partition is completed, the format process
will begin. A graphical bar will show the volume
being formatted. Please be patient during this
process. Do not turn off your NAS during this
process.
If you would like to change your settings at this
stage, click Exit.
The system will now update all of the changes
made.
Please be patient during this process. Do not turn
off your NAS during this process.
D-Link ShareCenter Quattro DNS-345 User Manual
67
Section 4 - Coniguration
The wizard is now complete. It will show the volume
number(s), ile system selected, the type of RAID,
and the disk formation in the RAID.
Click Finish to complete the process and start using
your DNS-345.
D-Link ShareCenter Quattro DNS-345 User Manual
68
Section 4 - Coniguration
RAID 1
Select RAID 1. All the drives are striped.
Click Next to continue.
Enter the amount of disk space you would like to
assign to the irst volume for RAID 1.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
69
Section 4 - Coniguration
Enter the amount of disk space you would like to
assign to the second volume for RAID 1.
Click Next to continue.
Click Enable Auto-rebuild to ix a RAID if it becomes
corrupted.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
70
Section 4 - Coniguration
Choose a volume or volumes that you would like
to encrypt.
Click Next to continue.
A warning message will appear, stating that your
device will have some latency.
Click Yes to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
71
Section 4 - Coniguration
Select Auto Mount to conigure the volume to
mount when the device becomes active.
Enter a password and conirm it.
Click Next to continue.
The ‘Volume Configuration Summary’ shows
details on all of the conigured drives. Check the
details on the list and click Format to continue or
click Previous to make changes.
D-Link ShareCenter Quattro DNS-345 User Manual
72
Section 4 - Coniguration
The next window will ask you to conirm your drive
selection.
Click Yes to agree.
Click No to exit.
Partitioning will now begin. Please be patient while
this process takes place. Do not turn off your NAS
during this process.
D-Link ShareCenter Quattro DNS-345 User Manual
73
Section 4 - Coniguration
Once the partition is completed, the format process
will begin. A graphical bar will show the volume
being formatted. Please be patient during this
process. Do not turn off your NAS during this
process.
If you would like to change your settings at this
stage, click Exit.
ShareCenter will format the second drive of the
volume as well
If you would like to change your settings at this
stage, click Exit.
D-Link ShareCenter Quattro DNS-345 User Manual
74
Section 4 - Coniguration
The system will now update all of the changes
made.
Please be patient during this process. Do not turn
off your NAS during this process.
The wizard is now complete. It will show the volume
number(s), ile system selected, the type of RAID,
and the disk formation in the RAID.
Click Finish to complete the process and start using
your DNS-345.
D-Link ShareCenter Quattro DNS-345 User Manual
75
Section 4 - Coniguration
Once you have completed the wizard. ShareCenter
will return to the main screen.
The RAID configuration you just set will be
displayed.
D-Link ShareCenter Quattro DNS-345 User Manual
76
Section 4 - Coniguration
RAID 5
Select RAID 5. All the drives are striped.
Click Next to continue.
Select a capacity for RAID 5 (in GB) then check the
box next to ‘Conigure the remaining disk space
as JBOD’ if you wish to conigure the remaining
space as JBOD.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
77
Section 4 - Coniguration
Click Enable Auto-rebuild to ix a RAID if it becomes
corrupted.
Click Next to continue.
Choose a volume or volumes that you would like
to encrypt.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
78
Section 4 - Coniguration
A warning message will appear, stating that your
device will have some latency.
Click Next to continue.
Select Auto Mount to conigure the volume to
mount when the device becomes active.
Enter a password and conirm it.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
79
Section 4 - Coniguration
The ‘Volume Configuration Summary’ shows
details on all of the conigured drives. Check the
details on the list and click Format to continue or
click Previous to make changes.
Click Next to continue.
The next window asks you to conirm your selection
to format the drives.
Click Yes to agree.
Click No to exit.
D-Link ShareCenter Quattro DNS-345 User Manual
80
Section 4 - Coniguration
Partitioning will now begin. Please be patient while
this process takes place. Do not turn off your NAS
during this process.
Once the partition is completed, the format process
will begin. A graphical bar will show the volume
being formatted. Please be patient during this
process. Do not turn off your NAS during this
process.
If you would like to change your settings at this
stage, click Exit.
D-Link ShareCenter Quattro DNS-345 User Manual
81
Section 4 - Coniguration
The system will now update all of the changes
made.
ShareCenter will format the second drive of the
volume too.
If you would like to change your settings at this
stage, click Exit.
D-Link ShareCenter Quattro DNS-345 User Manual
82
Section 4 - Coniguration
Once you have completed the wizard. ShareCenter
will return to the main screen.
The RAID configuration you just set will be
displayed.
D-Link ShareCenter Quattro DNS-345 User Manual
83
Table of Contents
RAID 5 + Spare
Select RAID 5. All the drives are striped.
Click Next to continue.
Click Create Spare Disk. This creates a
RAID 5 plus the spare.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
84
Table of Contents
The volume is now conigured for RAID 5 plus
the spare.
Click Next to continue.
Choose a volume or volumes that you would like
to encrypt.
A warning message will warn you that the system
will operate slower.
Click Yes to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
85
Table of Contents
Select Auto Mount if you wish to mount the
drive(s) without entering a password every time.
Enter the encryption password and enter it again
to conirm.
Click Next to continue.
ShareCenter will now show the Volume
Coniguration Summary.
Make sure under type it reads RAID5 + Spare.
Check the details on the list and click Format to
continue or click Previous to make changes.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
86
Table of Contents
The next window asks you to conirm your selection
to format the drives.
Click Yes to agree.
Click No to exit.
Partitioning will now begin. Please be patient while
this process takes place. Do not turn off your NAS
during this process.
D-Link ShareCenter Quattro DNS-345 User Manual
87
Table of Contents
Once the partition is completed, the format process
will begin. A graphical bar will show the volume
being formatted. Please be patient during this
process. Do not turn off your NAS during this
process.
If you would like to change your settings at this
stage, click Exit.
The system will now update all of the changes
made.
Please be patient during this process. Do not turn
off your NAS during this process.
D-Link ShareCenter Quattro DNS-345 User Manual
88
Table of Contents
The wizard is now complete. It will show the volume
number(s), ile system selected, the type of RAID,
and the disk formation in the RAID.
Click Finish to continue.
Once you have completed the wizard. ShareCenter
will return to the main screen.
The RAID configuration you just set will be
displayed.
D-Link ShareCenter Quattro DNS-345 User Manual
89
Section 4 - Coniguration
RAID 10
Select RAID 10. All drives are mirrored then striped.
Click Next to continue.
Select a capacity for RAID 10 (in GB) then check
the box next to ‘Conigure the remaining disk space
as JBOD’ if you wish to conigure the remaining
space as JBOD.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
90
Section 4 - Coniguration
Click Enable Auto-rebuild to repair a RAID if it
becomes corrupted.
Click Next to continue.
Choose a volume or volumes that you would like
to encrypt.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
91
Section 4 - Coniguration
A warning message will warn you that the system
will operate slower.
Click Next to continue.
Select Auto Mount to conigure the volume to
mount when the device becomes active.
Enter a password and conirm it.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
92
Section 4 - Coniguration
The ‘Volume Configuration Summary’ shows
details on all of the conigured drives. Check the
details on the list and click Format to continue or
click Previous to make changes.
A warning message will appear to inform you that
all volumes and data will be formatted and erased.
Click Yes to continue.
Click No to exit.
D-Link ShareCenter Quattro DNS-345 User Manual
93
Section 4 - Coniguration
Partitioning will now begin. Please be patient while
this process takes place. Do not turn off your NAS
during this process.
Once the partition is completed, the format process
will begin. A graphical bar will show the volume
being formatted. Please be patient during this
process. Do not turn off your NAS during this
process.
If you would like to change your settings at this
stage, click Exit.
D-Link ShareCenter Quattro DNS-345 User Manual
94
Section 4 - Coniguration
The system will now update all of the changes
made.
Please be patient during this process. Do not turn
off your NAS during this time.
The wizard is now complete. It will show the volume
number(s), ile system selected, the type of RAID,
and the disk formation in the RAID.
Click Finish to complete the process and start using
your DNS-345.
D-Link ShareCenter Quattro DNS-345 User Manual
95
Section 4 - Coniguration
Once you have completed the wizard. ShareCenter
will return to the main screen.
The RAID configuration you just set will be
displayed.
D-Link ShareCenter Quattro DNS-345 User Manual
96
Section 4 - Coniguration
A Quick S.M.A.R.T. Test
To perform the Quick S.M.A.R.T. Test, select the
drive or volume then select the Quick Test radio
button and click Start.
A warning message will prompt you to stop all
services and network activity.
Click Yes to continue the Quick S.M.A.R.T. test.
D-Link ShareCenter Quattro DNS-345 User Manual
97
Section 4 - Coniguration
The test will run and a percentage completed will
display under the Progress Tab.
The Start button will change to a Stop button.
Stop Button
Progress Tab
When the test is complete, the results will be
displayed under the Results Tab.
Results Tab
D-Link ShareCenter Quattro DNS-345 User Manual
98
Section 4 - Coniguration
Creating a Schedule for the S.M.A.R.T Test
To create a schedule, select the disks/volumes to
run the test on. Then under Schedule, select the
period (Daily/Weekly/Monthly) and from the dropdown list select the time.
Click Create
To view the Schedule List, click on the schedule
list arrow. A new table will appear showing details
of the new schedule created.
To delete a scheudle, click on the Trash Can.
D-Link ShareCenter Quattro DNS-345 User Manual
99
Section 4 - Coniguration
Scanning the volumes
¹º»¼ ½¾¿À ÁÂÃľÅÆ¿ » ÇÆÈÉÃÅ Èà ÈÆ¿È ÈÉÆ Å¾¿ÀÊs ile system on your ShareCenter Quattro. Scan Disk scans your disks ile system for
errors and/or corruption.
Click Management, then Disk Management, and
then Scan Disk.
Select the volume from the drop-down list you
wish to scan.
Click Scan Disk
D-Link ShareCenter Quattro DNS-345 User Manual
100
Section 4 - Coniguration
A warning message will prompt you to stop running
all services (hard drive and network activity)
Click Yes to proceed
Click No to cancel
The DNS-345 will initialize the volume(s) and begin
scanning.
Please wait while the software scans your machine
or click Exit to cancel the scan.
When the scan is complete, the table will either
display Success or Failure.
Click Finish to exit.
D-Link ShareCenter Quattro DNS-345 User Manual
101
Section 4 - Coniguration
Volume Encryption
Ëolume Encryption begins at the disk level right after you inished selecting you RAID option. Volume Encryption allows you to mount
the volume on startup without the need to re-enter a password at every login. Once encryption is set in Auto Mount, the drives will
automatically mount whenever the NAS starts up. Let’s take a look at the steps needed to complete Volume Encryption.
Under Hard Drive Coniguration, select the volume
you wish to encrypt. A warning message will appear
noting that enabling this option might impact the
performance of the device.
Click Yes to continue.
Next, you will be prompted to conigure the drive.
Select Auto Mount if you wish to setup encryption
when the NAS starts up.
Enter a password, then conirm it and click Next
to continue.
..NB:.Please.take.note.that.once.you.enable.volume.encryption.throughput.will.be.much.slower.
D-Link ShareCenter Quattro DNS-345 User Manual
102
Section 4 - Coniguration
If the passwords do not match then a message
will appear.
Click Yes, to re-enter the matching passwords.
The Volume Coniguration Summary shows which
volumes are encrypted and which ones are not.
Click Format to start the formatting process.
D-Link ShareCenter Quattro DNS-345 User Manual
103
Section 4 - Coniguration
A message will appear asking you to conirm your
hard drive selection for formatting.
Click Yes to start the formatting process.
Please be patient as the partitioning and formatting
process begins.
D-Link ShareCenter Quattro DNS-345 User Manual
104
Section 4 - Coniguration
When formatting is complete, a table displaying
the volumes formatted, partitioned, and encrypted
will appear.
Click Finish to close this window.
Go to Disk Management, Volume Encryption to
see a list of encrypted volumes.
Select the volume(s) you wish to modify. Your
selection(s) will turn ÌÍÎ.
Click Modify.
D-Link ShareCenter Quattro DNS-345 User Manual
105
Section 4 - Coniguration
Enter the password into the ield provided and
click Apply.
You have the option to enable Auto Mount and
enter a new password. If you choose not to enable
Auto Mount you can leave this ield blank.
Click Apply to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
106
Section 4 - Coniguration
The volumes will be partitioned and formatted
once again.
Please be patient while this process takes place.
Do not turn off your NAS during this process.
The wizard will return you to the Volume Encryption
page where you can view the encrypted volumes.
D-Link ShareCenter Quattro DNS-345 User Manual
107
Section 4 - Coniguration
Account Management - Creating Single Users
ÏÐÑ ÒÓÑÔÓÕÖÔ×ØÙÓ ÚÑÛØ ÜÓ ØÓÑÝ Þ× ßÔÑàÞÑ àÛÝ ÚàÛàáÑ ØÓÑÔ àÛÝ áÔ×ØÙ àßß×ØÛÞÓâ ÒÙ Þ× ãäå ØÓÑÔÓ àÛÝ æç áÔ×ØÙÓ ßàÛ èÑ ßÔÑàÞÑÝâ éê
default, all users have read and write access to all folders. However access rules can be created and edited in the Network Shares
menu.
Click Management, Account Management.
Under Users/Groups, User Settings click Create
The User Setup Wizard will appear.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
108
Section 4 - Coniguration
In Step 1, select ‘Create a Single User’
Click Next
In Step 2, enter the user name and password for
the new user.
Click Next to continue
D-Link ShareCenter Quattro DNS-345 User Manual
109
Section 4 - Coniguration
In Step 3, add the user to a group by entering the
group details. (If no group exists click Next)
Click Next to continue.
In Step 4, select the network share settings. Select
Read Only, Read/Write, or Deny Access.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
110
Section 4 - Coniguration
Assign Privileges/Access Methods for the user(s).
Check the options you need.
Click Next to continue.
WebDAV is one of the options.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
111
Section 4 - Coniguration
In Step 5, enter the amount of disk space you wish
to assign the user on each volume. Enter zero to
provide unlimited disk space to the user.
Click Next to continue.
The inal step is a summary of all the conigurations
you made.
Click Finish to accept the changes.
Click Exit to cancel the changes.
D-Link ShareCenter Quattro DNS-345 User Manual
112
Section 4 - Coniguration
Account Management - Creating Multiple Users
In Step 1, select ‘Create a Multiple user’
Click Next
Enter a username.
Enter the account prefix (Eg. this could be a
department in the company).
Enter the amount of users you want to create. Next
to the input ield is the remaining amount of users
you can add to the NAS.
Enter a password and conirm it.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
113
Section 4 - Coniguration
In Step 3, add the user to a group by entering the
group details.(If no group exists click Next)
Click Next to continue.
In Step 4, select the network share settings. Select
Read Only, Read/Write, or Deny Access.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
114
Section 4 - Coniguration
Assign Privileges/Access Methods for the user(s).
Check the options you need
Click Next to continue.
In Step 5, enter the amount of disk space you
wish to assign the user on each volume. Type 0 to
provide unlimited disk space to the user.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
115
Section 4 - Coniguration
The inal step is a summary of all the conigurations
you made.
Click Finish to accept the changes.
Click Exit to cancel the changes.
The User Settings window will show a list of the
users created.
D-Link ShareCenter Quattro DNS-345 User Manual
116
Section 4 - Coniguration
Account Management - Creating the same user
Click Management, Account Management.
Under Users/Groups, User Settings click Create
The User Setup Wizard will appear.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
117
Section 4 - Coniguration
In Step 1, select ‘Create a Single User’
Click Next
If you have created the same user twice, a
message will appear prompting you to enter a new
username.
Click Yes and enter a new username.
D-Link ShareCenter Quattro DNS-345 User Manual
118
Section 4 - Coniguration
Account Management - Modify Users
Click the user you wish to modify. The user will be
highlighted in red.
Click Modify to continue.
The User Setup Wizard will appear.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
119
Section 4 - Coniguration
In Step 1, change the username or password.
Click Next to continue
Change the Network Share Settings accordingly.
Click Next to continue
D-Link ShareCenter Quattro DNS-345 User Manual
120
Section 4 - Coniguration
Reassign Privileges/Access Methods for the
user(s).
Check the options you need
Click Next to continue.
In Step 4, enter the re-assigned amount of disk
space you wish to assign the user on each volume.
Type 0 to provide unlimited disk space to the user.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
121
Section 4 - Coniguration
The inal step is a summary of all the conigurations
you made.
Click Finish to accept the changes.
Click Exit to cancel the changes.
A message will appear stating the user details have
been changed successfully.
Click Yes to exit the wizard.
D-Link ShareCenter Quattro DNS-345 User Manual
122
Section 4 - Coniguration
Account Management - Deleting Users
Click the user you wish to delete. The user will be
highlighted in red.
Click Delete to continue.
A message will appear prompting you to conirm
deleting the user.
Click Yes to conirm.
The user is now automatically removed from the
list.
D-Link ShareCenter Quattro DNS-345 User Manual
123
Section 4 - Coniguration
Account Management - Importing Users
Click Account Management, Users/Groups
Click Import Users
The Import Users Wizard will start.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
124
Section 4 - Coniguration
In Step 1, click Download to see a sample ile.
Click Overwrite Duplicate Accounts if this is
necessary
Click Choose File to import the list.
Click Next to continue
Assign the privileges and access methods.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
125
Section 4 - Coniguration
If there are problems with the user list, the wizard
will show the errors in red on the table.
The Summary will show a list of imported users.
Click Finish to close the wizard or go back to
change the import ile.
D-Link ShareCenter Quattro DNS-345 User Manual
126
Section 4 - Coniguration
Account Management - Creating a Group
Click Account Management, Users/Groups
Click the blue arrow and the Group Settings will
appear.
Click New to create a new Group.
The Group Setup Wizard will now start.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
127
Section 4 - Coniguration
In Step 1, enter a Group Name.
Click Next to continue
In Step 2, click the checkbox to select the user(s)
you wish to add to the group.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
128
Section 4 - Coniguration
Select the Network Share Settings (read, read/
write, deny access) for the corresponding disk
volume for the group.
Click Next to continue.
Select the Assigned Privileges for the group.
The greyed out selections are there by default.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
129
Section 4 - Coniguration
Select the appropriate WebDAV settings.
Click Next to continue.
Enter the amount of space you want to assign
to the group for each volume. Enter zero to give
unlimited disk space to the group.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
130
Section 4 - Coniguration
The wizard is now complete. The last step shows a
summary of the group you created. Click Previous
to change your settings or Finish to end the wizard.
Under Group Settings, a table will show the group
you just created.
D-Link ShareCenter Quattro DNS-345 User Manual
131
Section 4 - Coniguration
Account Management - Modifying a Group
Click Account Management, Users/Groups
Click the blue arrow and the Group Settings table
will appear.
Select the group you want to modify. Your selection
will turn red.
Click Modify to change the settings for the Group.
D-Link ShareCenter Quattro DNS-345 User Manual
132
Section 4 - Coniguration
The Group Setup Wizard will now start.
Click Next to continue.
In Step 1, make the necessary modiications to
the group(s).
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
133
Section 4 - Coniguration
Select the appropriate Network Share Settings (read,
read/write, deny access) for the corresponding disk
volume for the group.
Click Next to continue.
Select the appropriate Assigned Privileges to the
group.
The greyed out selections are there by default and
cannot be modiied.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
134
Section 4 - Coniguration
Edit the amount of space you want to assign to the
group for each volume. Enter zero to give unlimited
disk space to the group.
Click Next to continue.
When editing the quota, make sure the size is not
smaller than the user quota on his/her account.
Click Yes to change the quota.
D-Link ShareCenter Quattro DNS-345 User Manual
135
Section 4 - Coniguration
The wizard is now complete and will show a
summary of the group you edited.
Click Previous to change your settings or Finish
to end the wizard. Exit will cancel all changes you
made.
D-Link ShareCenter Quattro DNS-345 User Manual
136
Section 4 - Coniguration
Account Management - Deleting a Group
Select the Group you want to delete.
Click Delete.
A warning message will appear asking you to verify
if you want to delete the Group.
Click Yes to delete the Group.
Click No to cancel your decision.
D-Link ShareCenter Quattro DNS-345 User Manual
137
Section 4 - Coniguration
Quota Settings
ëìí îìïðíñíòóíð ôõïóóðö ÷õøøöðó÷ ÷óöðïùí úõöóï÷ ûöð üöóì ùðöõø ïòý þòýþÿþýõï ÷ ÷÷þùòþòù ï úõöóï óö ï ùðöõø öð õ÷íð þ þ þó óìí ï öõòó öû ÷óöðïùí ï ö ïóíý
users and groups do not have a quota.
ýíûïõ ó
Click Enable to activate Quota Settings. The status
will now display ‘Started’, notifying you that the
Quota Settings have begun.
To Modify a User’s Quota Settings, click the blue
arrow to reveal a table of users.
D-Link ShareCenter Quattro DNS-345 User Manual
138
Section 4 - Coniguration
Select the User. Your selection will turn red.
Click Modify to change his/her settings.
The Quota Settings coniguration box will display
the user account you want to modify.
Enter a new volume quota amount.
Click Apply to conirm your settings.
D-Link ShareCenter Quattro DNS-345 User Manual
139
Section 4 - Coniguration
The modiied quota settings will be displayed in
the table.
For Group Quota Settings, click the blue drop
down arrow to view the group quota table.
D-Link ShareCenter Quattro DNS-345 User Manual
140
Section 4 - Coniguration
Select the group. Your selection will turn red.
Click Modify.
The Group Quota Settings screen will display the
group you want to modify.
Enter the new quota volume settings for the current
group.
Click Apply.
D-Link ShareCenter Quattro DNS-345 User Manual
141
Section 4 - Coniguration
The table under the Group Quota Settings window
will display the modiied quota settings.
D-Link ShareCenter Quattro DNS-345 User Manual
142
Section 4 - Coniguration
Network Shares
! "
be removed irst. This can be done simply by clicking on the Delete button. You can also mount .iso iles in the ISO Mount Shares Settings. When a user has access to a
mounted .iso, he/she will have also have access to all the iles on it.
#$%&'() *+,($-.
/ ISO Mount
Shares
add, modify, and remove both new and existing Network
Share and ISO Mount Share Settings.
To add a rule click on the New button. To modify an
existing rule click on the Modify button. To remove a
rule click on the Delete button.
To select a rule, simply click on the rule. Your selection
will turn red, indicating it is selected for use.
At the bottom of the table, the user can navigate through
pages and also refresh the window by click on the
Refresh button.
Click on the Reset Network Shares button to reset the
network access list to the default coniguration,
D-Link ShareCenter Quattro DNS-345 User Manual
143
Section 4 - Coniguration
Adding/Modifying New Network Shares Wizard
. To add a Network Share click on the New button. An easy to conigure wizard will
/01 234435678 91:;637 5644 <19:=6>1 035 ;3 ?<< ? 715 @1;53=A B0?=1 37 ;01 B0?=1C17;1=
launch.
This window welcomes the user to the setup
wizard for creating a new network share.
In this wizard the user will be able to:
1) Select share folders.
2) Conigure shared folder access rights.
3) Conigure network access settings.
4) View a summary of the coniguration before
completing.
Click Next to continue.
Select the Share Folder from one of the
volumes.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
144
Section 4 - Coniguration
DEFEGH HIE JKEL MGGNJOHK NL PLNJQ RISGI MLE
allowed to access this folder(s). Select All
Accounts to allow access to this folder to all
the accounts. Select Speciic User/group to
only allow certain users or groups access to this
folder.
Click Next to continue.
Select the appropriate access rights for the
share. Options to choose from are Read Only,
Read/Write, and Deny Access.
This procedure can also be used to block certain
users from accessing certain folders.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
145
Section 4 - Coniguration
TU VWX YZ[Z\] ^ Y_Z\`a\ XYZb c dbWX_ `e f]Z_ g
then this step allows you to set the access rights
for each User conigured on the ShareCenter
Click Next to continue.
If you selected speciic user/group in Step 2 then
this step allows you to set the access rights for
each Group conigured on the ShareCenter.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
146
Section 4 - Coniguration
hiji kli mnij opq pnnrsq tjrurvisin kw klrn nlpjix
Opportunistic locks (oplocks) are a characteristic
of the LAN Manager networking protocol
implemented in the 32-bit Windows family.
Oplocks are guarantees made by a server for
a shared logical volume to its clients. These
guarantees inform the Client that a ile’s content
will not be allowed to be changed by the server,
or if some change is imminent, the client will be
notiied before the change is allowed to proceed.
Oplocks are designed to increase network
performance when it comes to network ile
sharing. However it is recommended to set the
share oplocks to No (off) when using ile-based
database applications. When enabled, the ile
attribute “Map Archive” will be copied as the ile
is being stored on the ShareCenter Quattro.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
147
Section 4 - Coniguration
yz{z |}z ~z{ €‚ ƒ„‚ …†{z ‡{†|†€†ˆ
privileges that a user can use to access this
share. Options to choose from are FTP, NFS and
WebDAV. CIFS and AFP are set as default.
•
•
•
•
•
CIFS is short for Common Internet File
System.
AFP is short for Apple Filing Protocol.
FTP is short for File Transfer Protocol
NFS is short for Network File System.
WebDAV is short for Web-based Distributed
Authoring and Versioning.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
148
Section 4 - Coniguration
‰Š‹Š ŒŠ ŽŠ‹ ‘’ “’”•Ž‹Š ŒŠ –—˜
settings for
this share. FTP access can be:
1) FTP Anonymous None (No Access).
2) FTP Anonymous Read Only (Limited Access).
3) FTP Anonymous Read/Write (Full Access).
Click Next to continue.
If you checked NFS as an access method to
your network share then this step allows you to
set the parameters below:
•
•
•
Host - Allowable host address that can
access using NFS (* indicates all hosts)
Root Squash - Disables writing to the Root
owned directories and iles on the system
when the user has root access privileges.
Write - provide write permission to the ile
system.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
149
Section 4 - Coniguration
ebDAV as an access method
in Step 3, then this step will allow you to set the
access parameters.
™š ›œ žŸ ž¡ ¢ £
Click Next to continue.
Here a summary of the created shares will be
displayed.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
150
Section 4 - Coniguration
Deleting a Network Share
¤¥¦¥§¨ ¨©¥ ª¥¨«¬­® ¤©¯­¥ °¬± «²³© ¨¬ ´¥¦¥¨¥µ
Your selection will turn red.
Click Delete.
A warning message will appear prompting you to
verify if you wish to delete te Share.
Click Yes to delete.
Click No to Cancel.
D-Link ShareCenter Quattro DNS-345 User Manual
151
Section 4 - Coniguration
¶·¸ ¹¸º¸»¸¹ ¼·½¾¸ ¿Àºº Á¸ ¾¸ÂÃĸ¹ žÃ »·¸
Network Share List.
D-Link ShareCenter Quattro DNS-345 User Manual
152
Section 4 - Coniguration
Resetting the Network Shares
ÆÇÈÇÉÊ ÊËÇ
Reset Network Shares button.
A warning message will prompt you to conirm
your selection.
Click Yes to conirm.
Click No to cancel.
D-Link ShareCenter Quattro DNS-345 User Manual
153
Section 4 - Coniguration
Adding New ISO Mount Shares Wizard
. To add an ISO Mount, click on the New button. An
ÌÍÎ ÏÐÑÑÐÒÓÔÕ ÖÎ×ØÓÐÔ ÒÓÑÑ ÙÎÖ×ÚÓÛÎ ÍÐÒ ØÐ ÜÙÙ Ü ÔÎÒ ÝÞß àÐáÔØ ÐÔ ØÍÎ ÞÍÜÚÎâÎÔØÎÚ
easy to conigure wizard will launch.
The wizard provides these options
1. Select the .iso ile to be mounted.
2. Set the users and groups access rights to the
mounted .iso ile.
3. Add a comment describing the ile and select
the appropriate network protocols.
4. Conirm the changes.
Click Next to continue.
Expand one of your Volume File System trees to
select the desired .iso ile.
Check the box to the left of the .iso ile to select
it.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
154
Section 4 - Coniguration
ãääåæç èééêää ëìåíåîêæêä ïð ïñåä òóô õðöçï
share.
•
•
Select All Accounts to assign the ISO Mount
share read/deny privileges to all users.
Select Speciic User/Group in order to
assign read/deny privileges to individual
users and groups.
Click Next to continue.
The user can assign Read Only or Deny
Access privileges to the ISO Mount share here.
Click on the appropriate radio button for the
privileges you would like to assign.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
155
Section 4 - Coniguration
÷øø ù úûüüýþÿ ÿ
ùÿ øý
Share.
ú
ý
ÿ
ý
û
þÿ
Click Next to continue.
Assign more protocol privileges that a user can
use to access this share. Options to choose from
are FTP, NFS and WebDAV. CIFS and AFP are
set as default.
•
•
•
•
•
CIFS is short for Common Internet File
System.
AFP is short for Apple Filing Protocol.
FTP is short for File Transfer Protocol
NFS is short for Network File System.
WebDAV is short for Web-based Distributed
Authoring and Versioning.
•
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
156
Section 4 - Coniguration
summary of the share will be displayed.
Click on the Finish button to accept the change
and complete the wizard.
Through the D-Link Storage Utility, the ISO
Mount Share can now be mapped to your
computer as a normal network share.
D-Link ShareCenter Quattro DNS-345 User Manual
157
Section 4 - Coniguration
Admin Password
The Administrator Settings allows you to change
the Username and Password settings.
Enter a new Username
Type the original Password
Enter a New Password
Conirm the New Password
Click Save Settings to accept the changes
Click Don’t Save Settings to cancel changes
D-Link ShareCenter Quattro DNS-345 User Manual
158
Section 4 - Coniguration
Active Directory Settings
Allows you to conigure and communicate with a Windows Active Directory.
Active Directory is a Windows Server Service that
allows you or your company to manage an Active
Directory.
Check the box next to Enable Active Directory.
!" #! $! %&'( ) *)++,&*% ! -& # #! Active Directory server.
Enter a valid Username and Password provided by your systems
administrator.
Enter the DNS 1 and/or DNS 2 IP addresses.
Enter a Workgroup if required.
Enter a Real Name.
Enter an Active Directory Server name.
Click Save Settings to connect to the Active Directory.
Click Don’t Save Settings to cancel.
D-Link ShareCenter Quattro DNS-345 User Manual
159
Section 4 - Coniguration
Distributed File System
./012/34156 7/85 9:015; 5<=3850 = 351152 >85 ;=<=?5;5<1 0:015; @/1AB41 1A5 CB;D8/C=1/B<0 BE 0511/<? 4D 5=CA /<6/F/64=8 >85 0:015;G
Click Account Management,then Distributed
File System.
Check the Enable Distributed File System box.
A new table list will appear called the Root Folder
List.
Note:.For.Administrators.-.Setup.a.username.and.password.identical.to.each.PC.connected.to.the.NAS.for.DFS.to.work..
D-Link ShareCenter Quattro DNS-345 User Manual
160
Section 4 - Coniguration
Once you have access to the Root Folder List, click
New to create a new folder list.
You will be prompted to enter a Root Folder Name
in the ield.
Click Apply.
The Root Folder List will now show the new root
folder name and provide options to Modify, Delete,
or Conig Link.
D-Link ShareCenter Quattro DNS-345 User Manual
161
Section 4 - Coniguration
To modify a folder within the list, click Modify.
Enter a new folder name and click Apply.
The modiied name will be shown in the table.
To delete the folder list just click Delete.
D-Link ShareCenter Quattro DNS-345 User Manual
162
Section 4 - Coniguration
To Conig Link a Root Folder List click the Conig
Link button.
A new Root Folder Name table will appear below
the current Root Folder List.
Click New to conigure it.
The Distributed File System Settings box will
appear.
Enter a Local Share Name
Enter the Host IP address
Enter the Remote Share Folder or click Get
Remote Share Folder and click Apply
D-Link ShareCenter Quattro DNS-345 User Manual
163
Section 4 - Coniguration
If you do not know the Remote Share Folder
location, a warning message will appear notifying
you that the wizard was unable to ind the Remote
Share Folder.
Click Yes to enter the remote share folder manually.
Once you have entered the correct details, the
local share is created, displaying the host IP and
remote share folder address.
To delete a remote folder click the delete button.
D-Link ShareCenter Quattro DNS-345 User Manual
164
Section 4 - Coniguration
Network Management
HIJKLMN OPQPRISIQJ TLQJMLUV PQW SPQPRIV PUU XVVYIV MIZIMMXQR JL [\H VIJJXQRV] ^_IQ J`LYR` aLYM [\H VIJJXQRV KIMI TLQbRYMIW XQ J`I
Setup Wizard, it can still be conigured here. The LAN setup wizard allows you to conigure both LAN cards as a single device. This is
Ethernet Port Bonding and provides a more direct management of your LAN throughput. It also enables redundancy. If one of the ports
should fail, the other acts as backup. The network load is balanced across all links.
Go to Network Management, then LAN Setup.
Select the LAN port you wish to conigure. Your
selection will turn red.
Click Setup.
D-Link ShareCenter Quattro DNS-345 User Manual
165
Section 4 - Coniguration
The LAN setup wizard gives you the option to
conigure two main settings.
IP settings and VLAN settings.
Click Next to continue.
Step 1 allows you conigure your LAN settings.
Here you can choose between DHCP settings or
you can manually conigure your own LAN.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
166
Section 4 - Coniguration
Step 2 requires you to setup your VLAN settings.
Select the Enable radio button to enable VLAN
or click the Disable radio button to disable VLAN.
Enter a VLAN identiication number and click Next.
Step 3 shows a summary of what you just
conigured.
Click Finish to exit the wizard.
D-Link ShareCenter Quattro DNS-345 User Manual
167
Section 4 - Coniguration
co conigure the Link Aggregation settings, click the Enable radio button, then under option, select Round Robin. You can select other
link aggregation options from the drop-down list. The other options include Balance-XOR, Broadcast, 802.3ad, Adaptive Transmit Load
Balancing, and Adaptive Load Balancing.
For the Default Gateway, select either LAN 1 or LAN 2. The default gateway is your primary LAN port for accessing data on your
network.
A window will appear to inform you that changes
will take place after you login again.
Click OK, then logout and log back in to allow the
changes to take effect.
The wizard combined both LAN ports under one
coniguration group.
dee fghe iejklmn go ploq Aggregation termiinology under the help ile.
1..
D-Link ShareCenter Quattro DNS-345 User Manual
168
Section 4 - Coniguration
The basic LAN Setup also includes Link Speed
Settings and LLTD Settings. Choose the option
that suits your needs and click Save Settings to
continue.
Note:.Link.aggregation,.or.IEEE.802.3ad,.is.a.computer.networking.term.which.describes.using.multiple.Ethernet.network.
cables/ports.in.parallel.to.increase.the.link.speed.beyond.the.limits.of.any.one.single.cable.or.port,.and.to.increase.the.
redundancy.for.higher.availability..Link.aggregation.is.an.inexpensive.way.to.set.up.a.high-speed.backbone.network.
that.transfers.much.more.data.than.any.one.single.port.or.device.can.deliver..Link.aggregation.also.allows.the.network’s.
backbone.speed.to.grow.incrementally.as.demand.on.the.network.increases,.without.having.to.replace.everything.and.
buy.new.hardware..The.ShareCenter.Quattro.DNS-345.provides.this.feature.to.better.enable.the.network.it’s.on..Apply.
various.link.aggregation.options.that.warrant.support.for.your.network.
D-Link ShareCenter Quattro DNS-345 User Manual
169
Section 4 - Coniguration
Network Management - DDNS
rrst uvw xy uzw{|}~y €w {y ‚vƒ„… †‡ ˆ€w‰w„Šuz‹ Œ ‡ ƒww„Šz~| Žu}„z‹‡Œ ‡ ƒww„Šz~| Ž‘~yy y~„€zw‡Œ ’‡ wz“€”Œ z~ •‡ ‚‚‚.tzo.
com setup.
Go to Network Management, then Dynamic DNS.
Click Enable to select Dynamic DNS, then from
the drop-down list select the server, enter the Host
Name, username, password, verify the password,
and click Save Settings.
–—˜™š ›™œ™› ˜— ˜™ žŸ ¡¢£ žž–¤ ¥¡˜™ œ—› ¦—›™ §™˜¨¡©¥ —¢ ª›™¨˜¡¢« ¬—­› ž¬¢¨¦¡ª ž–¤ ª—¢¢™ª˜¡—¢ ®¡˜ žŸ ¡¢£ ¯›—§­ª˜¥° ˜˜¯¥š±±®®®.dlinkddns.com/howto.
D-Link ShareCenter Quattro DNS-345 User Manual
170
Section 4 - Coniguration
Network Management - UPnP Router Detection
²ou can conigure UPnP router detection and Port Forwarding in Network Management.
Note: You will need a UPnP router on your network.
Login and select Network Management, then click
the blue button to reveal the UPnP router settings.
Click Test to run a search.
The DNS-345 is searching for a router. Do not turn
off your NAS.
D-Link ShareCenter Quattro DNS-345 User Manual
171
Section 4 - Coniguration
A message will notify you that the wizard has found
a UPnP router on the network.
Click the blue arrow to reveal the Port Forwarding
options.
D-Link ShareCenter Quattro DNS-345 User Manual
172
Section 4 - Coniguration
Network Management - Port Forwarding
Login and select Network Management, then click
the blue arrow to reveal Port Forwarding settings.
Click Add.
The Port Forwarding wizard will starts.
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
173
Section 4 - Coniguration
In Step 1, select the Port Forwarding Rule that best
suits your needs.
Click Next to continue.
Select the default service you wish to Port Forward.
Note: You can select more than one port.
Click Previous to change the Port Forward Rule
or Finish to end the wizard.
D-Link ShareCenter Quattro DNS-345 User Manual
174
Section 4 - Coniguration
Application Management - FTP server
³´µ Application Management section allows you to conigure many services for your DNS-345. The server and service settings include:
FTP server, UPnP AV server, iTunes server, selected Add on features, AFP, and NFS services. Let’s begin by looking at coniguration
options for the FTP server.
Click Application Management,then FTP server.
From the drop-down menu select the amount of
users you want to give access to.
Set an idle time
Conigure the default FTP port
Select a default port range or select a passive
mode type
Select a language
Select the correct low control
Click to enable SSL/TLS and click Enable FXP to
continue
Click Save Settings to save the changes.
D-Link ShareCenter Quattro DNS-345 User Manual
175
Section 4 - Coniguration
The window expands to include a Blocked IP list
and FTP Server Status reports.
Click the blue arrow to see the drop-down list.
Click New to block a speciic IP address.
Enter the IP address of a machine you wish to
block.
Select permanent if you wish to block the IP
address permanently or Temporary if you wish to
set a time frame.
If your choice is permanent, click Apply and
continue.
D-Link ShareCenter Quattro DNS-345 User Manual
176
Section 4 - Coniguration
If your choice was Temporary, then you need to
select a blocked time frame.
Click Apply to continue.
The Blocked IP list will display the IP addresses
you blocked.
D-Link ShareCenter Quattro DNS-345 User Manual
177
Section 4 - Coniguration
Click the blue arrow next to FTP server status to
reveal the FTP details.
The FTP server is stopped by default. Click Start
FTP server to run the process.
D-Link ShareCenter Quattro DNS-345 User Manual
178
Section 4 - Coniguration
UPnP Server
¶·¸ ¹·º»¸¼¸½¾¸» ¿¸º¾À»¸Á º Âýà ÄV Server. This server provides the ability to stream photos, music and videos to UPnP AV compatible network media players. If the server
is enabled, the ShareCenter will be automatically detected by UPnP AV compatible media players on your local network. Click the Refresh All button to update all the
shared iles and folder lists.
Click Application Management, then UPnP
server.
Click the Enable radio button to enable the UPnP
server.
Click Add to conigure the UPnP share.
Select the volume you like to share and click
Apply.
D-Link ShareCenter Quattro DNS-345 User Manual
179
Section 4 - Coniguration
The system will not build the media library.
When the system has inished building the media
library, a sucess message will appear.
Click Yes to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
180
Section 4 - Coniguration
The selected volume will appear in the table under
the UPnP server.
D-Link ShareCenter Quattro DNS-345 User Manual
181
Section 4 - Coniguration
iTunes Server
To conigure the iTunes Server click Application
Management, then iTunes Server.
Click Enable next to iTunes Server.
Select the folder (usually Root) to place and share
your iTunes.
Enter a Password.
Select a Language.
Select an Auto Refresh option.
Click Save Settings.
ÅÆÇÈÉ ÈÊËÌÍÎÊÏ ÇÐÈ ÎÑunes server on the ShareCenter, launch iTunes. In your iTunes utility, select the ShareCenter and enter the iTunes server password if required.
Select the ShareCenter. When prompted, enter in the iTunes server password.
Click OK.
D-Link ShareCenter Quattro DNS-345 User Manual
Media stored on the ShareCenter will then be available for use in iTunes.
182
Section 4 - Coniguration
Add Ons
ÒÓÔ ÕÖÖ ×Ø ÙÔØÚ ÛÜÜÝÞß ÙÚÜàáâÜÔ ÛââÜáãÛàáÝØ ßÝäàÞÛåÔ àÝ ÛÖÖ ÔæàÔØÖÔÖ äÚØãàáÝØÛÜáàç àÝ çÝÚå èÓÛåÔéÔØàÔå. The Add on software is available from the D-Link website in your
country and some of them are available from the Installation Wizard. Below is a list of some of the supported Add-ons available.
Click the Refresh All button to update all the shared iles and folder lists.
Click Application Management, then Add Ons.
Click Choose File to locate the add on packages
on your local hard drive.
Once you have located the ile, select it and click
Open.
D-Link ShareCenter Quattro DNS-345 User Manual
183
Section 4 - Coniguration
Once the path of the package has been located,
click Apply to add the package.
Under Add-ons, a red message will appear to show
that the installation of the package was successful.
Click the Start button under Start/Stop.
D-Link ShareCenter Quattro DNS-345 User Manual
184
Section 4 - Coniguration
Click the Applications button at the top of the
browser. You will see your add-ons installed here.
Click it to enable the add-on.
òóëôõöï÷ø÷
ùúûüýþÿ  ýÿ û
û üýþÿ -like” interface
which can download and upload ShareCenter iles over
the internet. Ajaxplorer also allows a user, on any internet
connection, to stream video/audio and view image iles that
are stored on the ShareCenter.
ïíï
êøðíø÷
ÿÿ  ûÿ ý ÿ û  ÿ
share your photos over the web. It provides a convenient
interface from which you can create albums of photos with
descriptions. The albums are then accessible over the
web using HTTP so that your family and friends can then
view your ShareCenter stored photos from any internet
connection.
queezeCenter
•  ûÿ ÿ ÿ ÿ ÿ Media Squeezebox player so that it can play music iles
stored on your ShareCenter.
öï
(Wordpress)
òìîï
Streamer

û ÿ ÿ û
êëìíîïðñ Your ShareCenter CPU resources will be reduced depending on the
number of Add-ons you have enabled. Therefore for optimal performance make
sure to disable any add-ons not in use.
Note: To check the complete list of Add-on application software available consult
your local D-Link support page .
ë ìöø
û!þ
û " ûýýþûÿ #ÿ 
û û û
ÿ#
different media. It enables users to search for P2P iles over
networks. It works on all major platforms.
 û ÿ þÿ •
the ShareCenter’s internet connection the Blog created using
WordPress can be accessed and commented on from any
internet connection.
urn your ShareCenter into an Internet Streaming Music
site. From your ShareCenter, the Audio Streamer add-on
can transmit multiple streams of playing music iles to any
internet connection.
D-Link ShareCenter Quattro DNS-345 User Manual
185
Section 4 - Coniguration
AFP and NFS Services
$%& '%()&*&+,&) -.//0),- 1//2& 3424+5 '&)vice for connectivity with MAC OS based computers. If you need to use AFP service enable it here otherwise leave it disabled to
reduce CPU resource overhead.
The ShareCenter supports Network File System (NFS) service. To enable this multi-platform ile system on your ShareCenter enable it here. Otherwise disable the option to
prevent unnecessary CPU overhead. Click the ‘Refresh All’ button to update all the shared iles and folder lists.
Click Application Management, then AFP
Service.
Click the Enable radio button to turn AFP services
on
Click Save Settings to save the AFP services.
Click Application Management, then NFS
Service.
Click the Enable radio button to turn NFS services
on.
Click Save Settings to save the NFS service.
D-Link ShareCenter Quattro DNS-345 User Manual
186
Section 4 - Coniguration
System Management - Language
678 9:;<=:<8 >:?@A 789> =A8BA ?=ACDEFG8 C78 HIJKLMN CD C78FB A>8?FO? B8<FD;P HDQ;9D:R SD=B 9:;<=:<8 >:?@ TBDE C78 HKUF;@ Q8VAFC8 DB C78 WH :;R TD99DQ C78 F;ACB=?CFD;A
below. When you disable the language pack, the GUI will return to English.
Click System Management , then Language to
install a new language.
Click Choose File
Browse your computer hard drive for the selected
pack and click Apply.
If you have not selected a language package, a
message will prompt you to locate one.
Click Yes to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
187
Section 4 - Coniguration
System Management - Time and Date
XYZ Xime and Date coniguration option allows you to conigure, update, and maintain the correct time and date on the internal system clock. In this section you can set the
time zone that you are in, and set the NTP (Network Time Protocol) Server in order to periodically update your system time from the NTP Server. You can also use the time
and date of your compute as the system time.
Click System Management, then Time and Date.
Select the Set Time from My Computer button.
A conirmation message will appear.
Select the time zone.
D-Link ShareCenter Quattro DNS-345 User Manual
188
Section 4 - Coniguration
Select the NTP server.
Click Save Settings.
D-Link ShareCenter Quattro DNS-345 User Manual
189
Section 4 - Coniguration
System Management - Device
[\] ^]_`a] b]cc`deb fge] ghhijb kil ci gbb`ed g jimnemilfo dgp]o gd^ ^]bam`fc`id ci c\] ^]_`a]q rou can access this device by typing the host name in the URL section of
your web browser. For example: http://dlink-d10001
Click System Management, then Device.
Enter a Workgroup.
Enter a Name.
Enter a Description.
Click Save Settings to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
190
Section 4 - Coniguration
System Management - System Settings
stuvwx swvvyz{u |}~y€wu wut‚ƒƒwuu„…w †wv‡}wu v~ ƒ~zv}~… t~‡} ˆ‰s‚Š‹Œ Žuw}u ƒz }wuv}v vw ‰‘s’ }wuv~}w vw utuvwx v~ yv“s original state, set idle times, shutdown the
system, conigure settings, and conigure system temperature settings.
Click System Management , then System
Settings.
Click the Restart button to restart the DNS-345
Click the blue arrow to view the drop down list.
Click the Restore button to restore the system to
factory defaults.
Click the blue arrow to view the drop down list.
Click the Shutdown button to shutdown the
system.
Under Coniguration Settings, choose the ile you
want to load, click Load
Under Idle Time, click the blue arrow to view the
drop down list.
Type in the inactive time and click save settings.
Under System Temperature Threshold, click the
blue arrow to view the temperature settings.
Change the settings according to your needs and
click Save Settings.
D-Link ShareCenter Quattro DNS-345 User Manual
191
Section 4 - Coniguration
System Management - Power Management
”–— ˜–™š—›—œ—š žŸ™š ¡ ¢—š £™œ™¤—¥—œ ¦—™Ÿš— ™§§ ¢¨ © Ÿ  ª œ«¤Ÿš— –— ¬š­®—¨  ¨–Ÿ ¬ ¢œ ¢–­§— ¯ ¢—š š—¥™­œ¨ ª œ¨™œ  –— ¬—®­ª—° ”–— ¬š­®—¨ ¢­§§ ¯ ¢—š Ÿ¯
again when data is accessed.
Click System Management , then Power
Management.
Click Enable to enable hard drive hibernation.
Then from the drop-down list select a time frame.
Click the blue arrow to reveal Power Recovery.
Select Enable to use Power Recovery.
Click Save Settings to continue
D-Link ShareCenter Quattro DNS-345 User Manual
192
Section 4 - Coniguration
Click the blue arrow to reveal the Fan Control
Settings
Select a type of control settings
Click Save Settings to continue.
Click the blue arrow to reveal Power On/Off
Schedule Settings
Click Enable and choose the day and time for the
schedule.
Click Save Settings to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
193
Section 4 - Coniguration
Click the blue arrow to reveal OLED Display
Settings
Click Enable to Display the OLED for a speciic
time period.
Click Save Settings to continue
D-Link ShareCenter Quattro DNS-345 User Manual
194
Section 4 - Coniguration
System Management - Notiications
±²³ ´²µ¶³·³¸¹³¶ º»µ¹¹¶¼ ´½¾¹³¿ Àµ¸µÁ³¿³¸¹  ü¹ÄÅƵ¹Ä¼¸¾ dzµ¹»¶³ Ƶ¸ ȳ Ƽ¸ÅÁ»¶³É ¹¼ ¾³¸É ³Ê¿µÄË ¸¼¹ÄÅƵ¹Ä¼¸¾ ¹²µ¹ µË³¶¹ ½¼» µÈ¼»¹ ¼Ì³¶µ¹Ä¼¸µË µ¸É ɶÄͳ ¾¹µ¹»¾
conditions. These alerts can prove helpful in managing and safeguarding important data.
Click System Management, then Notiications,
and then E-mail Settings
Create an account by entering your e-mail details.
Click Save Settings to continue
Click System Management, then Notiications,
and then SMS Settings.
Follow the instructions on the wizard.
Click Next to proceed
D-Link ShareCenter Quattro DNS-345 User Manual
195
Section 4 - Coniguration
Step 1 Enter your SMS provider details.
Click Next to continue.
Click Save Settings to proceed.
D-Link ShareCenter Quattro DNS-345 User Manual
196
Section 4 - Coniguration
Click System Management, then Notiications,
and then Event Settings.
Select the events you wish to enable.
Click Save Settings to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
197
Section 4 - Coniguration
System Management - Logs
ÎÏÐÑÏÒ ÐÑÓ ÔÕÖ× ØÓÒÙ ÏÐÓØ ÚÕÙ ÛÜÒ ×ÓÐÙÝ ÚÕÙÞ ßÑÜÞÓàÓÒÐÓÞ ÐÕ ÞÓÛÓÏáÓ ÔÕÖ âáÓÒÐ× ãÞÕØ ÕÐÑÓÞ ßÑÜÞÓàÓÒÐÓÞ× ÕÞ ×ÓÒä ÐÑÓ ßÑÜÞÓàÓÒÐÓÞås log events to another ShareCenter or
SysLog server. You can also view the NAS system logs and the FTP logs here.
Click System Management, then Logs
Click the blue arrow to reveal the Server Settings
Click Enable Syslog
Enter an IP address
Click Save Settings.
Click the blue arrow to reveal the Logs
D-Link ShareCenter Quattro DNS-345 User Manual
198
Section 4 - Coniguration
System Management - Firmware Upgrade
æçè éêëìíîëè ïðñëîòè óîñè ìîôèõ êö õêìð÷è öø ùçèùô úøë îûò üð÷øîò ûèí ýëìíîëè ëè÷èîõèõ öø öçè òèþêùèÿ æçêõ õèùöêøû ðëøþêòèõ î ÷êûô öø ùçèùô úøë ûèí ýëìíîëè øû öçè
D-Link support website. If new irmware is available, download the ile to your local computer.
Click System Management, then Firmware
Upgrade
Click the blue arrow to reveal the current irmware
version.
Click Choose File to locate the new irmware
Click Browse/Open
Click Apply
The system will now reboot. Do not disconnect
the power.
D-Link ShareCenter Quattro DNS-345 User Manual
199
Section 4 - Coniguration
System Management - SNMP
Click System Management, then SNMP
Click Enable to activate SNMP.
Enter the SNMP community details.
Enable notiications and specify the IP address.
Click Save Settings to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
200
Section 4 - Coniguration
System Management - USB Devices
!"#$ %& '() *+#, -
Click the blue arrow button to reveal the UPS
Settings.
Click to enable the Network UPS.
Enter an IP address and click Save Settings.
The UPS Status will show the current status of
your UPS.
Click the blue arrow to reveal the USB storage
Information.
It displays information on the manufacturer, product
name, and size(capacity).
D-Link ShareCenter Quattro DNS-345 User Manual
201
Section 4 - Coniguration
Click the blue arrow to reveal Printer Information.
It displays information on the manufacturer, product
type, and connection details.
D-Link ShareCenter Quattro DNS-345 User Manual
202
Section 4 - Coniguration
System Status - System Info
./0 123405 146473 89:;<5648;9 3=<009 ><;?8@03 89:;<5648;9 ;9 4/0 AB1CDEFG 123405 H9:; ><;?8@03 89:;<5648;9 ;9 4/0 IJB >;<43K A0?8=0 H9:;<5648;9K 69@ L6<@ A<8?0
information. Hard Drive Info displays information on all hard drives including the manufacture details, temperatures, size, and status. Resource Monitor offers more detailed
specs on the CPU, Memory, Bandwidth, and Processes.
Click System Status, then System Info
Click the blue arrow from each of the headings to
reveal information on each segment.
LAN Information, Device Information, and Volume
Information.
Click System Status, then Hard Drive Info
Click the blue arrow to reveal a table of hard drive
information.
D-Link ShareCenter Quattro DNS-345 User Manual
203
Section 4 - Coniguration
Click the blue arrow to reveal the Resource
Monitoring details.
The monitor provides information on the CPU,
memory, bandwidth, and processes in action.
D-Link ShareCenter Quattro DNS-345 User Manual
204
Section 4 - Coniguration
Part III
D-Link ShareCenter Quattro DNS-345 User Manual
205
Section 4 - Coniguration
Applications
FTP/HTTP Downloads
Schedule ile and folder backups from an FTP server, web server, or local network share. Always test the URL before applying changes. This will help to ensure a successful
download.
MNOPQRST
•UV WXV YZ[\] ^_WW]`U W] UVaVbW WXV WcdV ]e UVY ver that the
source iles/folders for the Schedule Downloads are located
on. Click the HTTP radio button to specify that the source
iles are located on a web server. Click the FTP radio button
to specify that the source iles/folders are located on an FTP
server.
fRQgh iPOjRk
l`WVY WXV a]m\` \`e]YnZW\]` e]Y WXV U\WV WXZW b]`WZ\`U WXV oaVU
that you want to schedule for downloading. If no password
is required, choose Anonymous. If a password is required,
choose Account and provide the user name and password.
pqPShNrP
l`WVY WXV _UVY `ZnV XVYVs
tNqquRSk
l`WVY WXV dZUUv]Y[ XVYVs
wTxP
yVaVbW V\WXVY File or Folder from the drop-down list
depending on whether you wish to download a ile or a
folder. Choose File if you wish to download a speciic ile.
Choose Folder if you wish to download all the iles in a
speciic folder.
pzf
l`WVY WXV {|}~ ||} U\WV Z[[YVUU e]Y WXV UbXV[_aV[
download. Click on Test to verify access to the site address
and ile/folder. If you have chosen File from the above drop
down list, you must specify the exact ile in the URL path,
including the ile extension. (e.g. http://example.com/test/
testile.txt).
D-Link ShareCenter Quattro DNS-345 User Manual
206
Section 4 - Coniguration
€‚ƒ „…
†‡ˆ‰Š ˆ‹‰ Œ‰ŽŽ ‘‰Œˆ‡’ˆ“‡ “‡ ˆ‹‰ ‡ˆ‰Š‡’” ‘Š–‰Œ —“Š ˆ‹‰ ‘“˜‡”“’‘‰‘ ”‰Œ “Š —“”‘‰ŠŒ ˆ“ ™‰ Œ’–‰‘ ˆ“š ›”Žœ Browse to browse the internal
drives.
ƒžŸƒ
— ¡“¢ ˜“¢”‘ ”œ‰ ˆ“ Š‰‡’£‰ ’ ”‰ ’—ˆ‰Š ˆ ‹’Œ ™‰‰‡ ‘“˜‡”“’‘‰‘ —Š“£ ˆ‹‰ Œ‰Ž‰‘ ¤¥¥¦§¨¥¦ Œ‰Šver, enter the name you would like the ile to be
renamed to in this ield.
©žª«ªƒ
¯°ƒž
¬Œ‰ ˆ‹‰ ‘Š“­‘“˜‡ £‰‡¢ ˆ“ Œ‰”‰Žˆ ˆ‹‰ ”’‡®¢’®‰ ¢Œ‰‘ ‡ ˆ‹‰ ”‰ “Š —“”‘‰Š ˆ‹’ˆ ¡“¢ ’Š‰ ˆŠying to download.
±‰”‰Žˆ ˆ‹‰ ‘’ˆ‰ ’‡‘ ˆ£‰ —“Š ˆ‹‰ ‘“˜‡”“’‘ ˆ“ “ŽŽ¢Š.
ƒ²«³³´žª
— ¡“¢ ˜Œ‹ ˆ“ ŒŽ‹‰‘¢”‰ ’ Š‰Ž¢ŠŠ‡® ™’Žœ¢µ Œ‰”‰Žˆ ˆ‹‰ ‘‰ŒŠ‰‘ ‡ˆ‰Šval (daily, weekly, or monthly) and the time you want the backup to start.
€²°ƒ¶«·ƒ
¦‰‡‘‡® ’‡‘ Ž“£”‰ˆ‰‘ ‘“˜‡”“’‘ ‰–‰‡ˆŒ ˜”” ™‰ ”Œˆ‰‘ ‹‰Š‰š ¥‹‰ Ž¢ŠŠ‰‡ˆ Œˆ’ˆ¢Œ —“Š ‰’Ž‹ ‰–‰‡ˆ Œ ‘Œ”’¡‰‘ ‹‰Š‰š ‡ ’‘‘ˆ“‡µ ˆ‹‰Š‰ Œ ’‡ “ˆ“‡
Download
List
to delete a download event at any time. Current download statistics, such as % completed and download speed, are displayed for each event.
A refresh button is also provided to produce updated listings at any time.
D-Link ShareCenter Quattro DNS-345 User Manual
207
Section 4 - Coniguration
Login and select Applications, then FTP/HTTP
Select HTTP by clicking on the radio button.
Enter a URL.
Click Test to test the URL.
Under Save To, click the Browse button to save
your HTTP iles.
Enter (optional) details under Rename.
D-Link ShareCenter Quattro DNS-345 User Manual
208
Section 4 - Coniguration
Click Test to test the URL. The test results will
either show pass or fail.
Click Close to proceed.
Select a date and time for the download settings
Select a recurring backup time frame.
Click Save Setting to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
209
Section 4 - Coniguration
The table below will show the HTTP downloads.
To edit an item, select it irst then click Modify.
To delete an item, select it irst then click on the
Delete button.
D-Link ShareCenter Quattro DNS-345 User Manual
210
Section 4 - Coniguration
Applications - FTP Downloads
Click Applications, then FTP
Select Account as the Login Method.
Enter a username, password.
Select a type
Enter a URL
Browse to a location to save iles to.
Select the Language and Scheduling
Click Save Settings.
The table below will now show the FTP path and
status.
D-Link ShareCenter Quattro DNS-345 User Manual
211
Section 4 - Coniguration
For Anonymous settings:
Click the Anonymous radio button and follow the
rest of step 1.
Since the Login Method is Anonymous, the
username and password sections are greyed out.
Click Save Settings once complete.
D-Link ShareCenter Quattro DNS-345 User Manual
212
Section 4 - Coniguration
Remote Backups
¸¹º»¼¹ ½¾¿ÀÁÂà ¾ÄÄ»Åà ƻÁ ¼» Ǿ¿À Á ƻÁÈ Éʾȹ˹̼¹È ¼» ¾Ì»¼Ê¹È Éʾȹ˹̼¹È »È ÍÎÌÁÏ É¹Èver or vice versa from a remote ShareCenter or Linux Server to your
ShareCenter. Use the Create button in the remote backups list to start a wizard where you can conigure your ShareCenter’s Remote Backup functionality.
ÐÑÒÓÔÕ
remote
backup
service
ÖÒ××ØÙÚÛ
Ëʹ¿À ¼ÊÎÃ Ç»Ï ¼» ¹Ì¾ÇĹ ¼Ê¹ ȹº»¼¹ Ǿ¿ÀÁ ùÈver
functionality to access a remote NAS or Linux server.
Note: If you are not using the Remote Backup functionality
of your ShareCenter leave this box unchecked so that
your ShareCenter’s performance will not be affected by the
additional overhead used by this process.
ÜÌÂÁ¼ ¾ ¾ÃÃÅ»ÈÝ Ê¹È¹ ¼Ê¾¼ ¼Ê¹ ȹº»¼¹ ¿Äι̼ ÅÎÄÄ ÁùÞ
ßÕàÙáÕ
âÊÎà Îà ¼Ê¹ ÄÎü »ã ȹº»¼¹ Ǿ¿ÀÁ ä»Çà ÇÁÎļ ÇÆ ÂȹÃÃÎÌå ¼Ê¹
æÚÕÒáÕ
ËÄοÀ ¼Ê¹ Create button to build a new remote backup job
Backups list
Create button above the list to conigure each job.
on your ShareCenter.
çÙÛèéê
ËÄοÀ ¼ÊÎà ÇÁ¼¼»Ì ¼» º¾À¹ ¿Ê¾Ìå¹Ã ¼» Æ»ÁÈ ¹ÏÎüÎÌå ¸¹º»¼¹
Backup jobs in the Remote Backup list. You must select the
remote backup job irst and then click the modify button.
ëÕÔÕáÕ
âo remove a Remote Backup job select the job in the list and
then click the Delete button.
D-Link ShareCenter Quattro DNS-345 User Manual
213
Section 4 - Coniguration
Remote Backups - Create wizard
ìíîï ðñò óôõóö ÷íî Create button above the Remote Backup list a wizard will start, guiding you to conigure a new Remote Backup job.
øùúûüýù
ù Service Type
þõÿô ðÿ ÷íî ÿ÷îÿ ñ ÷íî õ ü : backup from the local NAS to a remote NAS
or vice versa.
NAS to Linux back from the local NAS to a Linux ile
system or vice versa
Local to Remote: sets the backup source as the local NAS
and the target destination for the backup iles as the remote
NAS or Linux ile system.
Remote To Local: sets the backup source as the remote
NAS or Linux ile system and the target destination for the
backup iles as the local NAS.
D-Link ShareCenter Quattro DNS-345 User Manual
214
Section 4 - Coniguration
Local
Settings
Remote
Settings
the name used to refer to the backup job
which will be listed later in the Remote Backup list.
Folder Path: select a local network share folder or ile as
the target or source for the backup job.
!" The backup process uses Rsync protocol and
needs to know the IP address of the destination source or
target device for the backup. Input the IP of the remote NAS
or Linux ile system.
Enable Encryption: Checking this box will enable SSH
encryption of the iles that are transferred (backed up) over
the network between the local and remote devices.
Ignore existing ile(s):Checking this box prevents the
backup process from writing over any iles in the target
ile system that are not part of the backup iles or folders.
Therefore any existing iles in the target system are
preserved.
Incremental backup support Num (#): Checking this
box provides multiple backup-capability at scheduled times.
The irst backup The irst backup in an incremental series
captures all the iles for backup. Subsequent backups are
incremental in that only the iles and the folders that have
changed in the backup source since the last incremental
backup will need to be backed up. Each incremental backup
builds a complete snapshot of the backup source however
only the initial backup contains all the original iles and
folders. The subsequent backups in the incremental series
contain new iles and folders plus the links to the irst
incremental backup.
D-Link ShareCenter Quattro DNS-345 User Manual
215
Section 4 - Coniguration
#$%& '(
Remote
Settings
#$%& /
Schedule
Settings
)%*+$% ,-$.: Using the browse button, select the ile
system (folder) path to the remote target or source system
for backup.
012345634 78439
Manual: Check either yes or no selection below to start
the backup (yes) immediately on completion of the wizard or
(no) manually start the backup from the Remote Backup list.
Once - select this option to run the Remote Backup once at
a speciic date and time set here.
Scheduled: select this option to set the backup to occur
daily, weekly, monthly per a speciic schedule.
D-Link ShareCenter Quattro DNS-345 User Manual
216
Section 4 - Coniguration
:;<= >?
Finished
J<KL;<
Backups list
@ABCD EF GHI Finish button if you are satisied with all
the settings of the Backup job created. Otherwise click
on the Previous button to go back and make changes.
Alternatively click on Exit to end the coniguration without
adding a Remote Backup job.
MNOP: The name of the Remote Backup job.
Schedule: When the Remote Backup job will execute.
Status: Current status which can be
• Ready the remote backup job is ready to be executed.
• Finished the remote backup job has executed completely
and successfully.
• Failed the Remote backup job was unsuccessful during
execution.
Enable/Disable: If the button shows a red circle the remote
backup job is enabled. Clicking the red button will disable
the remote backup job ad the button will change to a green
right pointing triangle. Clicking the green triangle will
enable the job again.
Backup now : Clicking this button will execute the backup
job immediately as long as the job is enabled.
D-Link ShareCenter Quattro DNS-345 User Manual
Restore: Clicking this button will write the backup iles
and folders back into the source ile system from the backup
target system (reverse the ile direction).
Navigation buttons: Use these buttons to move up and
down in the list when there are multiple jobs conigured.
Refresh Button: Click this button during a backup or
recovery process to monitor the progress by updating the
progress completed bar.
217
Section 4 - Coniguration
Local Backups
QRSTUVWT WXRYW ZWT Y[U \XWUT] ^YR_V`a \]Xb cST WXRYW [TcdX]_ aSY]T X\ cST UTefRT X] \]Xb cST WXRYW RXb`VcT]. Always test the URL before applying changes. This will help to
ensure a successful download.
ghijklmn
rlkst ujivlw
•aT cST ]YUfX ^VccX[a cX aTWTRc cST ^YR_V` bTcSXUo p\ qXV]
NAS device has two volumes you can click the Internal
Backup radio button to backup the data from the irst
volume to the second volume and vice-versa. The Internal
Backup feature also allows you to backup an existing folder
on a volume to another folder on the same volume but
nested folders in the same volume are not allowed.
If you want to backup the data from your PC or another
NAS device to your NAS device, click the LAN Backup radio
button.
x[cT] cST WXyf[ f[\X]bYcfX[ \X] cST afcT cSYc RX[cYf[a cST ZWTa
that you want to schedule downloads from. If no password
is required choose Anonymous. If a password is required
choose Account and provide the user name and password.
This option is only available for LAN Backups.
z{jmth|j
x[cT] cST VaT] [YbT VaTU ST]Too
}h{{~lmw
x[cT] cST `YaadX]U VaTU ST]To
n€j
QTWTRc File or Folder, depending on what you want to
download or backup.
zr
x[cT] the URL of the site or server you are initiating a transfer
from. E.g. ftp://123.456.789/Test or ftp://123.456.789/test.
txt
‚hƒj l
x[cT] Y eYWfU UTacf[YcfX[ U]feT X[ cST QSY]T„T[cT], or click
jth|j
x[cT] cST ]T[YbTU ZWT [YbT ST]To
Browse to select the destination.
D-Link ShareCenter Quattro DNS-345 User Manual
…vjt
x[cT] cST UYcT Y[U cfbT qXV dY[c cST aRSTUVWTU ^YR_V` X]
download to initiate.
j†‡mmstk
Backup
‰t†mj|jtihŠ
Backup
ˆTafy[YcT cST f[cT]val and time you want the backup or
download to run unattended.
“q UT\YVWc YWW WXRYW ^YR_V`a Y[U ZWT‹\XWUT] UXd[WXYUa
are in Overwrite mode, meaning that identical iles in the
destination folder will be overwritten by the source iles.
Checking Incremental Backup will have the ShareCenter
Quattro compare identical ile names at the source and
destination. Files will only be overwritten if the source ile is
more recent.
218
Section 4 - Coniguration
Local Backups - Time Machine
ŒŽ ‘’Ž”– —˜˜”™ ’ š› ’” ‘”–œš› ’ ž—›Ÿ–’› ” ’—’ Ž’ ‘”¡ — —‘¢š£ ¤’Ž–—’Ž”– Ž– ’ ¥—‘ ¦ž § Œime Machine. In order to use this function, the AFP
service is required. The AFP service will start automatically as soon as this function is enabled.
¨©ª«¬­ ®¯°­
Machine
®¯°­
Machine
Settings list
´­µ
¶­¬­·­
¹­°º»­ ª¬¬
Network
Shares
Ÿ˜Ž‘¢ ’Ž ’” –— ˜ ’ Œime Machine function to work with
a MAC OS X Time Machine. The Time Machine Settings list
will appear when this checkbox is ticked.
± ˜Ž’ ”² ¤’Ž–—’Ž”– ²”˜¤› ”– ’ ³’™”›¢ ž—›
associated with the Time Machine backup.
±¤¤ — ³±ž ²”˜¤› — — Œime Machine destination.
¸˜’ — ³±ž ²”˜¤› ’š£ — — Œime Machine destination.
¸˜’ —˜˜ ’ ³±ž ²”˜¤› Ž– ’ ˜Ž’ ‘”–œš›¤ — Œime
Machine Destinations.
D-Link ShareCenter Quattro DNS-345 User Manual
219
Section 4 - Coniguration
Local Backups - USB Backups
¼½¾¿ ¿ÀÁ¾ÃÄ ÅÆÆÃÇ¿ ½À È¿ÀÉ Âà ÁÃÄÊËÈÉÀ ½À ̽ÅÉÀÍÀÄÂÀÉ ¿Ã ½Å ¾Â ÎÀÁÃÏÀ¿ Å ÎÅÁÐÈÑ ÒÀ¿Â¾ÄžÃÄ ÓÃÉ ÅÄÔ ÕÌÖ ÒÀ×¾ÁÀ ½Å ¾¿ ÁÃÄÄÀÁÂÀÒ Âà ÔÃÈÉ ØÙÌÚÛÜÝÞ ßou can connect a
USB lash drive for uploading irmware, use an external hard drive to copy data from your NAS to the external storage, or connect another NAS for USB backup.
MTP Backups is a data solution that continuously secures your data and makes restoration easy. It allows for digital media data to be synchronized between your NAS and
portable devices. The main beneit to using MTP backups is that there is no need for drivers. The protocol resides on the NAS and all conigurations take place between your
NAS and the portable device.
D-Link ShareCenter Quattro DNS-345 User Manual
220
Section 4 - Coniguration
Click Applications, then Local Backup, and then
USB Backups
Click Browse under Destination. Find the volume
you want to backup to and click Save Settings.
All iles in this volume now support MTP.
Under USB Backups click the Enable radio button
Under Category, select your USB backup format,
USB to NAS or NAS to USB.
Clock Browse to locate your source.
D-Link ShareCenter Quattro DNS-345 User Manual
221
Section 4 - Coniguration
Under Source, select the path where you want to
backup.
Click Apply to continue.
Click Browse to ind the destination.
Select the path or USB device for your backup.
Click Apply to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
222
Section 4 - Coniguration
Select the Type you wish to copy
Click Save Settings.
D-Link ShareCenter Quattro DNS-345 User Manual
223
Section 4 - Coniguration
USB Print Server
The.ShareCenter.features.a.built-in.USB.print.server,.giving.users.the.ability.to.share.a.printer.on.their.local.network...
Connect.a.USB.printer.to.the.USB.port.on.the.back.of.the.ShareCenter..It.is.important.to.ensure.that.the.printer’s.drivers.
are.already.installed.on.any.computer.you.want.to.print.from.
Adding.a.Printer:
Click Start and select Printers and Faxes.
D-Link ShareCenter Quattro DNS-345 User Manual
224
Section 4 - Coniguration
Select Add a printer.
The.Windows®.Add.Printer.Wizard.will.launch:
Click Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
225
Section 4 - Coniguration
When prompted to choose a local, or network
printer, select “A network printer, or a
printer attached to another computer.”
Click Next to continue.
Select “Browse for a printer” and click Next
to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
226
Section 4 - Coniguration
Select Double-click DNS-345 from the Shared
Printers list to expand the tree.
Select the available USB printer, and click
Next to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
227
Section 4 - Coniguration
The.following.printer.driver.messages.will.appear:
Click Yes to continue.
Click OK to continue and select
a printer driver.
Select the appropriate printer driver from the
list and click OK to complete the wizard. If the
driver is not in the list, select Have Disk.
D-Link ShareCenter Quattro DNS-345 User Manual
228
Section 4 - Coniguration
Insert the print driver CD or browse to the
appropriate directory.
Select the appropriate driver ile, and click
Open to continue.
Click OK to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
229
Section 4 - Coniguration
Verify the driver is correct, and click OK
to continue.
The wizard will install the printer drivers, and
return a completion screen. Click Finish.
D-Link ShareCenter Quattro DNS-345 User Manual
230
Section 4 - Coniguration
The printer should now appear as an
available printer.
D-Link ShareCenter Quattro DNS-345 User Manual
231
Section 4 - Coniguration
P2P Downloads - Settings
àá âãäå æçáè éêè ëìá ëêáíîèïç ðñð òêóáôêìò æìáìîçæçáâ åçââäáîå
õöõ
üýþÿ ý
Schedule
ý
Download
õý
ÿ
÷çïç âãç èåçï ëìá çáìøôç êï òäåìøôç âãç ùççï âê ùççï úèáëâäêáû
àá âãç øôêë
ùïêäòçò âãç èåçï ëìá ëêáíîèïç âãç ïèááäáî
schedule for P2P downloads. Simply select the Start and
Stop block for the appropriate Time and Date.
÷çïç âãç èåçï ëìá çáìøôç êï òäåìøôç âãç ìèâêæìâäë òêóáôêìò
option.
ãç
èåçï ëìá ëãêêåç óãçâãçï âê ìôôêó âãç òçäëç âê
automatically choose an incoming connections port or
conigure the incoming connections port manually.
ÿ
ý Path
ÿýÿ
÷çïç âãç èåçï ëìá ëêáíîèïç åççòäáî êùâäêáåû
ãç
âêïïçáâ ùìâãå óäôô øç òäåùôìéçò ãçïçû
÷çïç âãç èåçï ëìá ëãêêåç âê çáìøôç êï òäåìøôç âãç çáëï yption
used.
ÿþ
Control
÷çïç âãç èåçï ëìá ëãêêåç âê ìôôêó âãç òçäëç âê ìèâêæìâäëìôôé
choose the bandwidth control speed, or you can manually
conigure the maximum download rate and maximum
upload rate. Enter the value -1 to set the respective ield to
unlimited.
D-Link ShareCenter Quattro DNS-345 User Manual
232
Section 4 - Coniguration
P2P Downloads - Downloads
‡ *++ ,-../01
from URL
*++ ,-../01
from File
9:9
Downloads
list
</=->/
Completed
!! " ! #$% &'& !"% ("! ($)
2
3(! 4"#$!! 5" ‡ 5" 7"% 8" " 3( 5" # !"% ("!!
onto your PC. This allows you to load the torrent ile from
your local PC.
2
$ %$ !"% (( $ ; 6 %$(( 7 !$4(5!)
Remove Completed button to
remove inished downloads. Sometimes identifying inished
jobs, when multiple downloads exist, can be dificult. This
option makes it is easier for the user to remove inished
downloads from the list with a single click.
? ($6 "
Details button allows the user to view the iles that are
being downloaded for each torrent.
@/1ABC
?
,-DEFDE
?
Down,Bottom
"45 ! 4 ($ 6 " torrent ile hosted on the internet. The BitTorrent download
manager will add the torrent ile to the download manager
and begin downloading your iles.
Top, Up, Down and Bottom buttons allow the user
to move the selected P2P download in the task list. The
downloads at the top of the list carries more priority than the
one list below them.
IA>BJA1B-0
</L./MN
ask window there are a couple of
navigation controls. When multiple tasks exist, the user can
select how many tasks will be displayed by using the dropdown menu. The user can also navigate to other pages when
more than one page exists.
 7""K "8 &'& ?
Refresh button allows the user to refresh the P2P task
list so it displays the most updated statistics.
?
Delete button allows the user to remove a selected
download. This will remove not only the torrent ile, but also
the partially downloaded iles too.
@/C/1/
?
G1A.1 H G1-D
?
Start and Stop buttons allow users to start and stop
selected P2P downloads in the task list.
D-Link ShareCenter Quattro DNS-345 User Manual
233
Section 4 - Coniguration
Web File Server
Whenever you cannot mount the network shares of your NAS, use the Web File Server to access the iles using a browser over the internet. If the network, that your
ShareCenter is connected to is using NAT then you will need to forward HTTP port 80 across your router for access over the internet.
OP
OPYZ[\
Up button to go up (or back) one directory in
the folder structure of the selected network share.
˜QRS TUVTW SXQ
]QUQTS ^ _Q`SVa^SVba RbU_Qc Va ^ aQSdbcW `X^cQ ef a^gVh^SVah
in the folder view on the left. Then left click the Upload
button to open a dialogue window where you can browse
to select a ile on your computer for uploading to the
destination folder.
iZjkYZ[\
]QUQTS ^ lUQ Sb _bdaUb^_ Sb fbmc TbnomSQc ef a^gVh^SVah Va
the folder view on the left. When you ind the ile left click
on it in the folder. Your selection will be highlighted in red.
Next click on the Download button and save or open the
ile as needed.
pqrsqtu
iZjkYZ[\
|ZP}
~Zq
iqYqwq
pqk[ƒq
…sZPqswyqt
the Refresh button to update the folder and ile
view of the Web File Server.
vqrw xYyxz
.
{bdaUb^_` SXQ lUQ Sb fbmc TbnomSQc
Copies the ile to the clipboard and opens a wizard to allow
you to select the folder to paste the ile into. Once you have
chosen the folder clicking OK to paste the ile into the folder.
€bgQ` SXQ lUQ Sb ^ aQd RbU_Qc ba SXQ _V`W
‚QnbgQ` SXQ `QUQTSQ_ lUQ Rcbn _V`W
„UUbd` fbm Sb TbalhmcQ ^ aQd lUQ a^nQ Rbc SXQ `QUQTSQ_ lUQ
{V`oU^f` SXQ lUQ ocboQcSVQ` `mTX ^` bdaQc`XVo† ^TTQ``
rights, and modify time.
D-Link ShareCenter Quattro DNS-345 User Manual
234
Section 4 - Coniguration
Amazon S3
Amazon S3 is an adjustable online storage facility. This feature is used on your DNS-345 to store and retrieve any amount of data. The Amazon S3 feature allows you to
create and modify iles that interact with your NAS in the cloud. Data can be stored and retrieved through a simple web interface from your NAS. Stored objects cannot be
larger than 5GBs, but users can store an unlimited amount of objects. All objects are retrievable with a unique key code assigned to each user.
D-Link ShareCenter Quattro DNS-345 User Manual
235
Section 1 - Product Overview
Photo Center
Photo Center is an Add-On tool for photos. You can create individual albums, group albums, Gallery’s, and etc. This application is managed and placed on your DNS-345
from the Applications window.
Login to your ShareCenter
Click Management, then click Application
Management.
D-Link ShareCenter Quattro DNS-345 User Manual
236
Section 1 - Product Overview
Click Add Ons
Then click Choose File to ind the Photo Center
Application on your computer.
Browse through your computer to ind the folder
for the application.
Click Open.
D-Link ShareCenter Quattro DNS-345 User Manual
237
Section 1 - Product Overview
The File Path has now been set.
Click Apply to continue.
Photo Center is now installed on the NAS.
Below File Path it should read Install Successfully.
In the table, you will see the Photo Center
application listed.
D-Link ShareCenter Quattro DNS-345 User Manual
238
Section 1 - Product Overview
Click the green arrow under Start/Stop to activate
the application.
Return to the Application window.
Photo Center will now appear under the Enabled
Add-Ons section.
Click Photo Center to launch the application.
D-Link ShareCenter Quattro DNS-345 User Manual
239
Section 1 - Product Overview
Under Launch, there is a brief description of Photo
Center.
Click Launch Interface to enter the online
program.
The application will now open in a new tab in your
browser. The program is ready to create a Gallery
in the following manners:
Add Albums
Add Comments
Add Items
Edit Albums
Edit Permissions
D-Link ShareCenter Quattro DNS-345 User Manual
240
Section 4 - Coniguration
My Favorites
The My Favorites tab allows you to add any icon you routinely access from the Applications or Management Tab in one
convenient location for quick and easy access. You can add icons to the My Favorites tab using two different methods.
D-Link ShareCenter Quattro DNS-345 User Manual
241
Section 4 - Coniguration
Add an Icon to My Favorites
ou can either right click the icon and select: Add to My Favorites or use the Drag and Drop method.
ˆ‰Š‹Š Œ‹Š Ž ‘Š‰’“  Œ’’”•– Œ• —™•  š› œŒ‹”Š“ž Ÿ
Both are shown below.
Method 1:
Right click on an icon in the applications
or management tab and click on the
Add to My Favorite menu item from the
command list that appears.
Method 2:
Click and hold the left mouse button
down over the icon and drag it over to the
My Favorites tab. You will see a white
arrow pointing to the My Favorites tab
while you are dragging the icon.
D-Link ShareCenter Quattro DNS-345 User Manual
242
Section 4 - Coniguration
Removing an Icon from My Favorites
o remove an Icon from the My Favorites tab, simply right click on it and select Remove From My Favorite in the context selection that appears.
Right click an Icon in the My Favorites
tab and select the Remove From My
Favorite option. The Icon alias should
disappear from the My Favorites tab view.
D-Link ShareCenter Quattro DNS-345 User Manual
243
Section 5 - Knowledge Base
Knowledge Base
What is RAID?
¡¢£¤¥ ¦§¨©ª «¨© ¡¬­®¯­°¯ª ¢©©°± ¨« £¯­¬²¬¯­¬¯ª ¤³¦´¦¥ ³¦ ° µ¨¶·³¯°ª³¨¯ ¨« ª¸¨ ¨© ¶¨©¬ ­³¦´¦ ¸³ª§ ª§¬ °³¶ ¨« ²©¨¹³­³¯º «°®»ª ª¨»¬©°¯µ¬ °¯­ ²¬©«¨©¶°¯µ¬ ³¶²©¨¹¬¶¬¯ª¼ ½§¬©¬
are several different levels of RAID, with each one providing a different method of sharing or distributing data amongst the drives. The ShareCenter™ Quattro supports JBOD,
RAID 0, RAID 1, and Standalone.
¾¿ÀÁ Ä
RAID 0 provides data striping, which spreads out blocks
of data over all the drives, but does not provide data
redundancy.
Although performance is improved, the lack of fault
tolerance means that if one drive fails, all data in the array
will be lost.
D-Link ShareCenter Quattro DNS-345 User Manual
¾¿ÀÁ Â
¡¢£¤ à ²©¨¹³­¬¦ ¶³©©¨©³¯º ¨¹¬© ¶®»ª³²»¬ ­³¦´¦¥ ¸³ª§ ª§¬ ¦°¶¬
read/write speed of a single disk. A RAID 1 array can only be as
large as it’s smallest member disk.
Because the data is stored on multiple disks,
RAID 1 provides fault tolerance and protection, in addition to
performance advantages.
244
Section 4 - Coniguration
ÅÆÇÈ É
RAID 5 provides data striping with distributed parity, which stores information that can be used to reconstruct data. A
RAID 5 array will be the size of all the combined disks capacity minus the capacity of one disk, e.g. If there are 4x 80GB
disks in the array, the arrays capacity will be 240GB (3x80GB).
Implementing RAID 5 on the ShareCenter Pro allows it to continue operating even if one of the disks fails.
The diagram below indicates the operation of RAID 5:
D-Link ShareCenter Quattro DNS-345 User Manual
245
Section 4 - Coniguration
RAID OPTIONS
ÊËÌË ÍÎ Ï ÐÍÎÑ ÒÓ ÑÔË ÕÖ×Ø ÒÙÑÍÒÚÎ ÏÛÏÍÐÏÜÐË ÒÚ ÑÔË ÝÔÏÌËÞËÚÑËÌ ßàÏÑÑÌÒ ØáÝâãäå
Standard RAID - creates a single volume for one
drive or more drives.
JBOD - allows you to create a large virtual disk
drive by concatenating two or more smaller drives
together. The individual hard drives that makes
up a JBOD RAID can be different sizes and
manufacturers. The total size of the JBOD RAID
is the combined total of all the individual drives in
the set.
RAID 0 lets you assign two or more disks as a striped set. Once you create
the striped set, you will see it as a single disk drive. But when you write data to
the RAID 0 striped set, the data will be distributed across all of the drives that
make up the set. Because each disk has less to do, it takes less time to write
the data. The same is true when reading data; instead of a single disk having
to seek out and then send a large block of data, multiple disks each stream
their part of the data stream. As a result, RAID 0 striped sets can provide a
dynamic increase in disk performance.
D-Link ShareCenter Quattro DNS-345 User Manual
246
Section 4 - Coniguration
RAID 1 lets you assign two disks as a mirrored set.
Once you create the mirrored set, you will see it
as a single disk drive. But when you write data to
the mirrored set, it will duplicate the data across all
members of the set. This ensures that your data is
protected against loss if any hard drive in the RAID
1 set fails. In fact, as long as any single member
of the set remains functional, you will continue to
operate normally, with complete access to your
data.
RAID 5 is another striping RAID level, designed to
increase the speed of disk reads and writes. RAID
5 provides drive failure tolerance, allowing any
single drive in the array to fail without losing any
data in the array. When a drive fails, the RAID 5
array can still be used to read or write data. Once
the failed drive is replaced, the RAID 5 array can
enter a data recovery mode, where the parity data
in the array is used to rebuild the missing data on
the newly installed drive.
D-Link ShareCenter Quattro DNS-345 User Manual
247
Section 4 - Coniguration
RAID 10 is a nested RAID system created by
combining RAID 1 and RAID 0. The combination
is known as a stripe of mirrors. The difference is
that each member of the striped set has its data
mirrored. This ensures that if any single drive in
the RAID 10 array fails, the data is not lost. RAID
10 requires a minimum of four drives and can be
expanded in pairs.
D-Link ShareCenter Quattro DNS-345 User Manual
248
Section 4 - Coniguration
RAID Comparison Chart
RAID level
Minimum Drives
Protection
Description
Standard
1
None
C r e a t e s a s i n g l e Saves on costs
volume for one drive
or several drives
No data protection
like proper RAID
JBOD
1
None
Allows you to create a Saves on costs
large virtual disk drive
by concatenating two
or more smaller drives
together.
No redundancy
and limited data
protection.
RAID 0
2
None
Data striping without
redundancy
High Performance
No data protection,
one drive fails, all is
lost
RAID 1
2
Single drive failure
Disk mirroring
High data protection
High redundancy
cost because all
data is duplicated,
twice the storage
capacity is required
RAID 5
3
Single drive failure
Block-level data
striping with
distributed parity
High data protection,
support multiple
simultaneous reads
and writes
Write performance is
slower than RAID 0
or RAID 1
RAID 5+Spare
3
Single drive failure
Data striping across
all drives.
High data protection.
RAID 10
4
1 Disk per mirrored
stripe
Combination of RAID Highest data
0 (data striping) and protection, can
RAID 1 (mirroring)
tolerate multiple
drive failures.
D-Link ShareCenter Quattro DNS-345 User Manual
Strengths
Weaknesses
High redundancy
cost because all
data is duplicated,
twice the storage
capacity is required.
249
Section 5 - Knowledge Base
USB Print Server
ver, giving users the ability to share a printer on their local network. Connect a USB printer to the USB port on the back of
the ShareCenter™. It is important to ensure that the printer’s drivers are already installed or available on any computer you want to print from.
æçè éçêëèìèíîèëï ðèêîñëèò ê óñôõîöôí ÷éø ùëôíî òèë
Note: Only Printer function is supported. The ShareCenter does not support the copy and scan functions of Multi-Function Printers.
Log into ShareCenter
D-Link ShareCenter Quattro DNS-345 User Manual
250
Section 5 - Knowledge Base
Click Management
Click System Management, then USB Devices.
Click the blue arrow to view the Printer Information.
D-Link ShareCenter Quattro DNS-345 User Manual
251
Section 5 - Knowledge Base
Connect to your ShareCenter with Samba and
then double click the lP icon.
The.Windows®.Add.Printer.Wizard.will.launch:
Select the printer driver from the installed
Manufacturer list or use the Have Disk button
to browse for the printer driver ile.
Click OK to continue.
D-Link ShareCenter Quattro DNS-345 User Manual
252
Section 5 - Knowledge Base
Once you have selected the proper driver
as shown in the browse list then click OK to
install the printer.
The printer is now installed and the printer
queue will appear.
D-Link ShareCenter Quattro DNS-345 User Manual
253
Section 5 - Knowledge Base
úûü ýûþÿüü
UPS Connectivity
üÿ üþÿü þ ý ý þ üÿvice, giving users the ability to share the UPS on their local network. Connect a UPS to the USB port on the back
of the ShareCenter™.
Log into ShareCenter
D-Link ShareCenter Quattro DNS-345 User Manual
254
Section 5 - Knowledge Base
Click Management
Click System Management, then USB Devices.
Click the blue arrow next to UPS Settings. There
are two modes, Standalone and Master.
The UPS Status screen shows the mode,
manufacturer, product type, battery charge meter,
and status
D-Link ShareCenter Quattro DNS-345 User Manual
255
Section 5 - Knowledge Base
Under Mode, select Master from the drop-down list
Click Add
Enter the IP address of the other NAS on the
network.
Click the ‘+’ button to add more IP addresses. If you
do not add an IP address a message will appear.
D-Link ShareCenter Quattro DNS-345 User Manual
256
Section 5 - Knowledge Base
The message will asks you to enter an IP address.
Click Yes to continue.
Once you have entered an IP address, the system
will check its database for IP address records.
D-Link ShareCenter Quattro DNS-345 User Manual
257
Section 5 - Knowledge Base
The UPS Settings table will display the
IP address(es) you added.
D-Link ShareCenter Quattro DNS-345 User Manual
258
Section 5 - Knowledge Base
Deleting a UPS Slave
Under Management, System Management, UPS
Devices, select the IP address. Your selection will
turn red.
Click Delete.
The DNS-345 will process your request.
D-Link ShareCenter Quattro DNS-345 User Manual
259
Section 5 - Knowledge Base
The IP address will no longer be listed in the table.
D-Link ShareCenter Quattro DNS-345 User Manual
260
Section 5 - Knowledge Base
Knowledge Base
What is Ethernet Bonding?
Ž s perspective, channel bonding or “port trunking” -- combines both of the computer’s interfaces into a single interface that looks like nothing out of the
ordinary to your applications. A combined logical interface can provide load balancing and fault tolerance. The OS can alternate which interface it uses to send trafic, or it
can gracefully fail over between them in the event of a problem. You can even use it to balance your trafic between multiple wide area network (WAN) connections, such as
DSL and cable, or dialup and your next door neighbor’s unsecured Wi-Fi.
The DNS-345 has several options under Link Aggregation. Here are there uses:
Round-robin mode is good for general purpose load balancing between the adapters, and if one of them fails, the link will stay active via the other. The other six mode
options provide features for different setups.
• Mode 1, active backup, uses just one adapter until it fails, then switches to the other.
• Mode 2, balance XOR, tries to balance trafic by splitting up outgoing packets between the adapters, using the same one for each speciic destination when possible.
• Mode 3, broadcast, sends out all trafic on every interface.
• Mode 4, dynamic link aggregation, uses a complex algorithm to aggregate adapters by speed and other settings.
• Mode 5, adaptive transmit load balancing, redistributes outgoing trafic on the ly based on current conditions.
• Mode 6, adaptive load balancing, does the same thing, but attempts to redistribute incoming trafic as well by sending out ARP updates.
Complex modes are most likely unnecessary for home use. If you have a lot of network trafic you are looking to manage, consult the bonding driver documentation. For
most folks, bonding’s fault tolerance and failover is a larger gain than any increased link speed. For example, bonding two WAN links gives you load balancing and fault
tolerance between them, but it does not double your upstream throughput, since each connection (such as a Web page HTTP request) has to take one or the other route.
D-Link ShareCenter Quattro DNS-345 User Manual
261
Download PDF