Ryobi | RTS30 | Operator`s manual | Ryobi RTS30 Operator`s manual

OPERATOR’S MANUAL
10 in. Table Saw
RTS10
Your table saw has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFERENCE
table of contents
















Introduction.......................................................................................................................................................................2
Warranty............................................................................................................................................................................2
General Safety Rules..................................................................................................................................................... 3-4
Specific Safety Rules..................................................................................................................................................... 4-5
Symbols......................................................................................................................................................................... 6-7
Electrical............................................................................................................................................................................8
Glossary of Terms..............................................................................................................................................................9
Features..................................................................................................................................................................... 10-13
Tools Needed .................................................................................................................................................................13
Loose Parts............................................................................................................................................................... 14-15
Assembly................................................................................................................................................................... 16-23
Operation................................................................................................................................................................... 24-36
Adjustments............................................................................................................................................................... 37-39
Maintenance....................................................................................................................................................................39
Troubleshooting......................................................................................................................................................... 40-41
Parts Ordering/Service...................................................................................................................................... Back Page
INTRODUCTION
This tool has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability have
been given top priority in the design of this product making it easy to maintain and operate.
warranty
RYOBI® POWER TOOL - LIMITED TWO YEAR WARRANTY AND 30 DAY EXCHANGE POLICY
One World Technologies, Inc., warrants its RYOBI® power tools with the following conditions:
30-DAY EXCHANGE POLICY: During the first 30 days after date of purchase, you may either request service under this
warranty or you may exchange any RYOBI® power tool which does not work properly due to defective workmanship or
materials by returning the power tool to the dealer from which it was purchased. To receive a replacement power tool
or requested warranty service, you must present proof of purchase and return all original equipment packaged with the
original product. The replacement power tool will be covered by the limited warranty for the balance of the two year period
from the date of the original purchase.
WHAT THIS WARRANTY COVERS: This warranty covers all defects in workmanship or materials in your RYOBI® power
tool for a period of two years from the date of purchase. With the exception of batteries, power tool accessories are
warranted for ninety (90) days. Batteries are warranted for two years.
HOW TO GET SERVICE: Just return the power tool, properly packaged and postage prepaid, to an Authorized Service
Center. You can obtain the location of the Service Center nearest you by contacting a service representative at One
World Technologies, Inc., P.O. Box 1207, Anderson, SC 29622-1207, by calling 1-800-525-2579 or by logging on to
www.ryobitools.com. When you request warranty service, you must also present proof of purchase documentation, which
includes the date of purchase (for example, a bill of sale). We will repair any faulty workmanship, and either repair or replace
any defective part, at our option. We will do so without any charge to you. We will complete the work in a reasonable time,
but, in any case, within ninety (90) days or less.
WHAT’S NOT COVERED: This warranty applies only to the original purchaser at retail and may not be transferred. This
warranty only covers defects arising under normal usage and does not cover any malfunction, failure or defects resulting
from misuse, abuse, neglect, alteration, modification or repairs by other than Authorized Service Centers. One World
Technologies, Inc. makes no warranties, representations or promises as to the quality or performance of its power tools
other than those specifically stated in this warranty.
ADDITIONAL LIMITATIONS: Any implied warranties granted under state law, including warranties of merchantability or
fitness for a particular purpose, are limited to two years from the date of purchase. One World Technologies, Inc. is not
responsible for direct, indirect, or incidental damages, so the above limitations and exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
2
GENERAL SAFETY RULES
 SECURE WORK. Use clamps or a vise to hold work when
practical. It’s safer than using your hand and frees both
hands to operate tool.
 DON’T OVERREACH. Keep proper footing and balance
at all times.
 MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for better and safer performance. Follow
instructions for lubricating and changing accessories.
 DISCONNECT TOOLS. When not in use, before
servicing, or when changing attachments, blades, bits,
cutters, etc., all tools should be disconnected.
 AVOID ACCIDENTAL STARTING. Be sure switch is off
when plugging in any tool.
 USE RECOMMENDED ACCESSORIES. Consult the
operator’s manual for recommended accessories. The
use of improper accessories may risk injury.
 NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is unintentionally
contacted.
 CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect
its operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
 USE THE RIGHT DIRECTION OF FEED. Feed work into
a blade or cutter against the direction of rotation of blade
or cutter only.
 NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
THE POWER OFF. Don’t leave tool until it comes to a
complete stop.
 PROTECT YOUR LUNGS. Wear a face or dust mask if
the cutting operation is dusty.
 PROTECT YOUR HEARING. Wear hearing protection
during extended periods of operation.
 DO NOT ABUSE CORD. Never yank cord to disconnect
from receptacle. Keep cord away from heat, oil, and sharp
edges.
 When operating a power tool outside, use
an outdoor extension cord marked “W-A”
or “W”. These cords are rated for outdoor use and
reduce the risk of electric shock.
 K E E P B L A D E S C L E A N , S H A R P, and w ith
sufficient set. Sharp blades minimize stalling
and kickback.
 KEEP HANDS AWAY FROM CUTTING AREA. Keep
hands away from blades. Do not reach underneath work
or around or over the blade while blade is rotating. Do not
attempt to remove cut material when blade is moving.
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
READ ALL INSTRUCTIONS
 KNOW YOUR POWER TOOL. Read the operator’s
manual carefully. Learn the saw’s applications and
limitations as well as the specific potential hazards related
to this tool.
 G U A R D A G A I N S T E L E C T R I C A L S H O C K b y
preventing body contact with grounded
surfaces. For example, pipes, radiators, ranges,
refrigerator enclosures.
 KEEP GUARDS IN PLACE and in good working order.
 REMOVE ADJUSTING KEYS AND WRENCHES. Form
habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
 KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents. DO NOT leave tools or pieces
of wood on the saw while it is in operation.
 DO NOT USE IN DANGEROUS ENVIRONMENTS. Do
not use power tools in damp or wet locations or expose
to rain. Keep the work area well lit.
 KEEP CHILDREN AND VISITORS AWAY. All visitors
should wear safety glasses and be kept a safe
distance from work area. Do not let visitors contact
tool or extension cord while operating.
 MAKE WORKSHOP CHILDPROOF with padlocks and
master switches, or by removing starter keys.
 DON’T FORCE TOOL. It will do the job better and safer
at the feed rate for which it was designed.
 USE RIGHT TOOL. Don’t force the tool or attachment to
do a job it was not designed for. Don’t use it for a purpose
not intended.
 USE THE PROPER Extension Cord. Make sure
your extension cord is in good condition. Use only a
cord heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. A wire
gauge size (A.W.G.) of at least 14 is recommended for an
extension cord 25 feet or less in length. If in doubt, use
the next heavier gauge. The smaller the gauge number,
the heavier the cord.
 DRESS PROPERLY. Do not wear loose clothing, gloves,
neckties, or jewelry. They can get caught and draw you
into moving parts. Rubber gloves and nonskid footwear
are recommended when working outdoors. Also wear
protective hair covering to contain long hair.
 ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impactresistant lenses, they are not safety glasses.
3
GENERAL SAFETY RULES
 STAY ALERT AND EXERCISE CONTROL. Watch what
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
 DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
 USE ONLY CORRECT BLADES. Do not use blades with
incorrect size holes. Never use blade washers or blade
bolts that are defective or incorrect. The maximum blade
capacity of your saw is 10 in. (254 mm).
 Before making a cut, be sure all adjustments
are secure.
 BE SURE BLADE PATH IS FREE OF NAILS. Inspect for
and remove all nails from lumber before cutting.
 Never touch blade or other moving parts during
use.
 NEVER START A TOOL WHEN ANY ROTATiNG
C O M P O N E N T I S I N C O N TA C T W I T H T H E
WORKPIECE.
 DO NOT operate A tool while under the
influence of drugs, alcohol, or any
medication.
 When servicing use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
 Use only recommended accessories listed
in this manual or addendums. Use of accessories that
are not listed may cause the risk of personal injury.
Instructions for safe use of accessories are included with
the accessory.
 DOUBLE CHECK ALL SETUPS. Make sure blade is tight
and not making contact with saw or workpiece before
connecting to power supply.
 Blade coasts after being turned off.
 NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
 Inspect TOOL CORDS periodically. If damaged,
have repaired by a qualified service technician at
an authorized service facility. The conductor with
insulation having an outer surface that is green with
or without yellow stripes is the equipment-grounding
conductor. If repair or replacement of the electric cord
or plug is necessary, do not connect the equipmentgrounding conductor to a live terminal. Repair or replace
a damaged or worn cord immediately. Stay constantly
aware of cord location and keep it well away from the
rotating blade.
 Inspect EXTENSION CORDS periodically and
replace if damaged.
 GROUND ALL TOOLS. If tool is equipped with threeprong plug, it should be plugged into a three-hole
electrical receptacle.
 CHECK WITH A QUALIFIED ELECTRICIAN or service
personnel if the grounding instructions are not completely
understood or if in doubt as to whether the tool is properly
grounded.
 Use only correct electrical devices: 3-wire
extension cords that have 3-prong grounding plugs and
3-pole receptacles that accept the tool’s plug.
 DO NOT MODIFY the plug provided. If it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
 Keep TOOL dry, clean, and free from oil and
grease. Always use a clean cloth when cleaning. Never
use brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
SPECIFIC SAFETY RULES
 FIRMLY BOLT THE SAW TO A WORK BENCH OR LEG
STAND at approximately hip height.
NEVER OPERATE THE SAW ON THE FLOOR.
GUARD AGAINST KICKBACK. Kickback occurs when
the blade stalls rapidly and workpiece is driven back
towards the operator. It can pull your hand into the blade
resulting in serious personal injury. Stay out of blade path
and turn switch off immediately if blade binds or stalls.
 USE RIP FENCE. Always use a fence or straight edge
guide when ripping.
 SUPPORT LARGE PANELS. To minimize risk of blade
pinching and kickback, always support large panels.
 Remove all fences and auxiliary tables
before transporting saw. Failure to do so can result in an
accident causing possible serious personal injury.
 ALWAYS USE BLADE GUARD, Spreader, AND ANTIKICKBACK PAWLS on all “through-sawing” operations.
Through-sawing operations are those in which the blade
cuts completely through the workpiece as in ripping or
cross cutting. Keep the blade guard down, the antikickback pawls down, and the spreader in place.
 ALWAYS SECURE work firmly against the rip fence or
miter gauge. NEVER use the rip fence during the same
operation as the miter gauge.
 When making non-through RIP cuts, always
use a push stick, push block, and/or featherboard so your
hands do not come within 3 inches of the saw blade.
 When ripping narrow stock, always use a push
stick, push block, or featherboard.
4
SPECIFIC SAFETY RULES
 NEVER perform any operation “freehand” which means
using only your hands to support or guide the workpiece.
Always use either the rip fence or miter gauge to position
and guide the work.
 NEVER stand or have any part of your body in line with
the path of the saw blade.
 NEVER reach behind, over, or within three inches of the
blade or cutter with either hand for any reason.
 MOVE THE RIP FENCE out of the way when cross cutting.
 DO NOT USE THE Miter gauge AND RIP FENCE
during the same operation.
 NEVER use rip fence as cutoff gauge when cross
cutting.
 NEVER attempt to free a stalled saw blade without first
turning the saw OFF and disconnecting the saw from the
power source.
 PROVIDE ADEQUATE SUPPORT to the rear and sides
of the saw table for wide or long work pieces.
 AVOID KICKBACKS (work thrown back toward you)
by:
a) Keeping blade sharp.
b) Keeping rip fence parallel to the saw blade.
c) Keeping spreader, anti-kickback pawls, and
blade guard in place and operating.
d) Not releasing the work before it is pushed all the
way past the saw blade using a push stick.
e) Not ripping work that is twisted or warped or
does not have a straight edge to guide along the
fence.
 IF THE POWER SUPPLY CORD IS DAMAGED, it must
be replaced only by the manufacturer or by an authorized
service center to avoid risk.
 Use only recommended accessories listed
in this manual or addendums. Use of accessories that
are not listed may cause the risk of personal injury.
Instructions for safe use of accessories are included with
the accessory.
 make sure the work area has ample lighting
to see the work and that no obstructions will interfere with
safe operation BEFORE performing any work using the
table saw.
 ALWAYS TURN OFF SAW before disconnecting it, to
avoid accidental starting when reconnecting to power
supply.
 ONLY USE BLADES within the thickness range stamped
on the spreader/riving knife.
 THIS TOOL should have the following markings:
a)
b)
c)
d)
e)
f)
g)
h) Never operate saw on floor or below waist height.
Wear eye protection.
Use saw blade guard and spreader/riving knife for
every operation for which it can be used, including
all through sawing.
Keep hands out of the line of saw blade.
Use a push stick when required.
Pay particular attention to instructions on reducing
risk of kickback.
Do not perform any operation freehand.
Never reach around or over the saw blade.
 Never cut more than one piece of material
at a time.
 SAVE THESE INSTRUCTIONS. Refer to them
frequently and use to instruct other users. If you loan
someone this tool, loan them these instructions also.
 AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a sudden slip could cause your hand
to move into the cutting tool.
5
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
Safety Alert
Indicates a potential personal injury hazard.
Read Operator’s Manual
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye Protection
Always wear eye protection marked to comply with ANSI
Z87.1.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
Wet Conditions Alert
Do not expose to rain or use in damp locations.
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
W
Watt
Power
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic of current
No Load Speed
Rotational speed, at no load
Class II Construction
Double-insulated construction
Per Minute
Revolutions, strokes, surface speed, orbits etc., per minute
min
no
.../min
6
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
CAUTION:
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to the nearest
AUTHORIZED SERVICE CENTER for repair. When servicing, use only identical replacement parts.
To avoid serious personal injury, do not attempt to use this
product until you read thoroughly and understand completely the operator’s manual. If you do not understand
the warnings and instructions in the operator’s manual,
do not use this product. Call Ryobi customer service for
assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and, when needed, a full face shield. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye
protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
7
ELECTRICAL
Extension Cords
SPEED AND WIRING
Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug.
When using a power tool at a considerable distance from the
power source, use an extension cord heavy enough to carry
the current that the tool will draw. An undersized extension
cord will cause a drop in line voltage, resulting in a loss of
power and causing the motor to overheat. Use the chart
provided below to determine the minimum wire size required
in an extension cord. Only round jacketed cords listed by
Underwriter's Laboratories (UL) should be used.
The no-load speed of this tool is approximately 5,000 rpm.
This speed is not constant and decreases under a load or
with lower voltage. For voltage, the wiring in a shop is as
important as the motor’s horsepower rating. A line intended
only for lights cannot properly carry a power tool motor. Wire
that is heavy enough for a short distance will be too light for
a greater distance. A line that can support one power tool
may not be able to support two or three tools.
Grounding Instructions
This product must be grounded. In the event of a malfunction or
breakdown, grounding provides a path of least resistance for
electric current to reduce the risk of electric shock. This tool is
equipped with an electric cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged
into a matching outlet that is properly installed and grounded
in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
**Ampere rating (on tool faceplate)
0-2.0
2.1-3.4
3.5-5.0
5.1-7.0 7.1-12.0 12.1-16.0
Cord LengthWire Size (A.W.G.)
25'
16
16
16
16
14
14
50'
16
16
16
14
14
12
100'
16
16
14
12
10
—
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
WARNING:
When working with the tool outdoors, use an extension cord
that is designed for outside use. This is indicated by the
letters “W-A” or “W” on the cord’s jacket.
Improper installation of the grounding plug can result in
a risk of electric shock. When repair or replacement of
the cord is required, do not connect the grounding wire
to either flat blade terminal. The wire with insulation having an outer surface that is green with or without yellow
stripes is the grounding wire.
Before using an extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
WARNING:
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if
in doubt as to whether the tool is properly grounded.
Repair or replace a damaged or worn cord immediately.
This product is for use on a nominal 120 volt circuit and
has a grounding plug similar to the plug illustrated in
figure 1. Only connect the product to an outlet having the
same configuration as the plug. Do not use an adapter with
this product.
Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber,
tools or other obstructions while you are working with a
power tool. Failure to do so can result in serious personal
injury.
WARNING:
Check extension cords before each use. If damaged
replace immediately. Never use product with a damaged
cord since touching the damaged area could cause
electrical shock resulting in serious injury.
Electrical Connection
This product is powered by a precision built electric motor.
It should be connected to a power supply that is 120 V, AC
only (normal household current), 60 Hz. Do not operate
this product on direct current (DC). A substantial voltage
drop will cause a loss of power and the motor will overheat.
If the saw does not operate when plugged into an outlet,
double check the power supply.
Grounding
Pin
8
120 V Grounded
outlet
Fig. 1
GLOSSARY OF TERMS
Anti-Kickback Pawls (radial arm and table saws)
A device which, when properly installed and maintained,
is designed to stop the workpiece from being kicked back
toward the front of the saw during a ripping operation.
Arbor
The shaft on which a blade or cutting tool is mounted.
Bevel Cut
A cutting operation made with the blade at any angle other
than 90° to the table surface.
Compound Cut
A cross cut made with both a miter and a bevel angle.
Cross Cut
A cutting or shaping operation made across the grain or the
width of the workpiece.
Cutterhead (planers and jointer planers)
A rotating cutterhead with adjustable blades or knives. The
blades or knives remove material from the workpiece.
Dado Cut
A non-through cut which produces a square-sided notch or
trough in the workpiece (requires a special blade).
Featherboard
A device used to help control the workpiece by holding
it securely against the table or fence during any ripping
operation.
FPM or SPM
Feet per minute (or strokes per minute), used in reference
to blade movement.
Freehand
Performing a cut without the workpiece being guided by a
fence, miter gauge, or other aids.
Push Blocks (for jointer planers)
Device used to feed the workpiece over the jointer planer
cutterhead during any operation. This aid helps keep the
operator’s hands well away from the cutterhead.
Gum
A sticky, sap-based residue from wood products.
Heel
Alignment of the blade to the fence.
Kerf
The material removed by the blade in a through cut or the
slot produced by the blade in a non-through or partial cut.
Kickback
A hazard that can occur when the blade binds or stalls,
throwing the workpiece back toward operator.
Miter Cut
A cutting operation made with the workpiece at any angle
to the blade other than 90°.
Set
The distance that the tip of the saw blade tooth is bent (or
set) outward from the face of the blade.
Push Blocks (for table saws)
Device used to hold the workpiece during cutting operations. This aid helps keep the operator’s hands well away
from the blade.
Push Sticks (for table saws)
Device used to push the workpiece during cutting operations. A push stick should be used for narrow ripping operations. The aid helps keep the operator’s hands well away
from the blade.
Resaw
A cutting operation to reduce the thickness of the workpiece
to make thinner pieces.
Resin
A sticky, sap-based substance that has hardened.
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object in one
minute.
Ripping or Rip Cut
A cutting operation along the length of the workpiece.
Riving Knife/Spreader/Splitter (table saws)
A metal piece, slightly thinner than the blade, which helps
keep the kerf open and also helps to prevent kickback.
Saw Blade Path
The area over, under, behind, or in front of the blade. As it
applies to the workpiece, that area which will be or has been
cut by the blade.
Snipe (planers)
Depression made at either end of a workpiece by cutter
blades when the workpiece is not properly supported.
Through Sawing
Any cutting operation where the blade extends completely
through the thickness of the workpiece.
Throw-Back
The throwing back of a workpiece usually caused by the
workpiece being dropped into the blade or being placed
inadvertently in contact with the blade.
Workpiece or Material
The item on which the operation is being done.
Non-Through Cuts
Any cutting operation where the blade does not extend
completely through the thickness of the workpiece.
Worktable
Surface where the workpiece rests while performing a
cutting, drilling, planing, or sanding operation.
Pilot Hole (drill presses)
A small hole drilled in a workpiece that serves as a guide for
drilling large holes accurately.
9
FEATURES
PRODUCT SPECIFICATIONS
Input......................................................................15 Amps
No Load Speed..................................... 5,000 r/min. (RPM)
Cutting Depth at 0°....................................................... 3 in.
Cutting Depth at 45°...............................................2-5/8 in.
Blade Arbor............................................................... 5/8 in.
Blade Diameter........................................................... 10 in.
Blade Tilt.................................................................0° - 45°
Rating................................................120 V, AC only, 60 Hz
BLADE GUARD
spreader/ RIVING
KNIFE
RIP FENCE
FRONT
RAIL
anti-kickback
pawls
LOCKING
LEver
MITER
gauge
SCALE
BEVEL
SCALE
SWITCH
HEIGHT/bevel
ADJUSTING
HANDWHEEL
BEVEL
LOCKING
LEVER
Fig. 2
10
FEATURES
HEIGHT/BEVEL ADJUSTING HANDWHEEL - Located on
the front of the cabinet, use this handwheel to lower and
raise the blade for height adjustments or blade replacement. This handwheel also makes the adjustment for bevel
angles easy.
KNOW YOUR TABLE SAW
See Figure 2.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
MITER GAUGE - The miter gauge aligns the wood for a
cross cut. The easy-to-read indicator shows the exact angle
for a miter cut.
ANTI-KICKBACK PAWLS - Kickback is a hazard in which
the workpiece is thrown back toward the operator. The teeth
on the removable anti-kickback pawls point away from the
workpiece. If the workpiece should be pulled back toward
the operator, the teeth dig into the wood to help prevent or
reduce the possibility of kickback.
MITER GAUGE GROOVEs - The miter gauge rides in the
grooves on the saw table.
RIP FENCE - A sturdy metal fence guides the workpiece
and is secured with the locking lever.
SCALE - Located on the front rail, the easy-to-read scale
provides precise measurements for rip cuts.
BEVEL SCALE - The easy-to-read scale on the front of the
cabinet shows the exact blade angle.
SPREADER / RIVING KNIFE - A removable metal piece
of the blade guard assembly, slightly thinner than the saw
blade, which helps keep the kerf open and prevent kickback.
When in the through sawing, or “up” position, it is higher
than the saw blade and becomes a spreader. When in the
non-through sawing, or “down” position, it is below the saw
blade teeth and becomes a riving knife.
BLADE - This saw is provided with a 24-tooth, 10 in. carbide
blade. The blade is raised and lowered with the height/bevel
adjusting handwheel. Bevel angles are locked with the bevel
locking lever.
WARNING:
SWITCH ASSEMBLY - This saw has an easy access power
switch located below the front rail. To lock the switch in the
OFF position, remove the switch key from the switch. Place
the key in a location that is inaccessible to children and
others not qualified to use the tool.
Do not use blades rated less than the speed of this tool.
Failure to heed this warning could result in personal
injury.
BLADE GUARD - Always keep the removable blade guard
down over the saw blade for through-sawing cuts.
Bevel LOCKING LEVER - This lever, placed just under
the saw table surface on the front of the cabinet, locks the
angle setting of the blade.
11
FEATURES
Operating Components
WARNING:
The upper portion of the blade projects up through the table
and is surrounded by an insert called the throat plate. The
height of the blade is set with a handwheel on the front of
the cabinet. To accommodate wide panels, the saw table
has rails on each side. Detailed instructions are provided in
the Operation section of this manual for the basic cuts: cross
cuts, miter cuts, bevel cuts, and compound cuts.
ALWAYS remove the switch key when the tool is not in
use and keep it in a safe place. In the event of a power
failure, turn the switch off ( O ) and remove the key. This
action will prevent the tool from accidentally starting
when power returns.
The rip fence is used to position work for lengthwise cuts.
A scale on the front rail shows the distance between the rip
fence and the blade.
WARNING:
ALWAYS make sure your workpiece is not in contact with
the blade before operating the switch to start the tool.
Failure to heed this warning may cause the workpiece to
be kicked back toward the operator and result in serious
personal injury.
It is very important to use the blade guard assembly for
all through-sawing operations. The blade guard assembly
includes: riving knife/spreader/splitter, anti-kickback pawls,
and plastic blade guard.
SWITCH assembly
See Figure 3.
This saw is equipped with a switch assembly that has a
built-in locking feature. This feature is intended to prevent
unauthorized and possible hazardous use by children and
others.
WARNING:
To reduce the risk of accidental starting, Always make
sure the switch is in the off ( O ) position before plugging
tool into the power source.
TO TURN YOUR SAW ON:
 With the switch key inserted into the switch, lift the switch
to turn on ( l ).
SWITCH
ON
TO TURN YOUR SAW OFF:
 Press the switch down to turn off ( O ).
SWITCH
OFF
TO lock your saw:
 Press the switch down.
 Remove the switch key from the switch and store in a
safe, secure location.
SWITCH KEY
SWITCH IN LOCKED POSITION
Fig. 3
12
FEATURES
BLADES
WARNING:
For maximum performance, it is recommended that you
use the 24-tooth, 10 in. carbide-tipped combination blade
provided with your saw. Additional blade styles of the same
high quality are available for specific operations such as
ripping. Your local dealer can provide you with complete
information.
Do not use blades rated less than the speed of this tool.
Failure to heed this warning could result in personal
injury.
Kerf width must be within the limits stamped on the spreader/
riving knife.
TOOLS NEEDED
The following tools (not included or drawn to scale) are needed for assembly and making adjustments:
Framing Square
Phillips
Screwdriver
FlatHEAD
Screwdriver
COMBINATION
SQUARE
SOCKET WRENCH
with 10 mm and
11 mm socket
C-CLAMPS
Fig. 4
13
LOOSE PARTS
The following items are included with the table saw:
d
c
e
b
f
A
g
M
L
h
K
j
I
Fig. 5
A. Anti-Kickback Pawls................................................. 1
B. Blade Guard.............................................................. 1
C. Switch Key................................................................ 1
D. Handle....................................................................... 1
E. Miter Gauge.............................................................. 1
F. Rip Fence.................................................................. 1
G. Locking Lever........................................................... 1
14
H. Screw........................................................................ 2
I. Open End Wrench..................................................... 1
J. Closed End Wrench.................................................. 1
K. Hex Key (5 mm)........................................................ 1
L. Push Stick Storage Screw........................................ 2
M.Push Stick................................................................. 1
LOOSE PARTS
The following items are included with the table saw leg stand:
I
G
D
C
C
D
E
I
F
E
B
H
A
A
E
I
B
H
H
F
I
H
A.Lower Brace...............................................................2
B.Lower Side Brace.......................................................2
C.Upper Brace...............................................................2
D.Upper Side Brace.......................................................2
E.Hex Nut....................................................................20
15
Fig. 6
F. Carriage Bolt (1/4 - 20 x 1/2 in.)...............................16
G.Carriage Bolt (1/4 - 20 x 1-3/8 in.).............................4
H Foot............................................................................4
I. Leg.............................................................................4
ASSEMBLY
UNPACKING
WARNING:
This product requires assembly.
 Carefully lift saw from the carton and place it on a level
work surface.
NOTE: This tool is heavy. To avoid back injury, keep your
knees bent and lift with your legs, not your back, and get
help when needed.
Do not lift the saw without help. Hold it close to your
body. Keep your knees bent and lift with your legs, not
your back. Ignoring these precautions can result in back
injury.
WARNING:
WARNING:
Never stand directly in line with the blade or allow hands
to come closer than 3 in. to the blade. Do not reach over
or across the blade. Failure to heed this warning can
result in serious personal injury.
Do not use this product if any parts on the Loose Parts List
are already assembled to your product when you unpack
it. Parts on this list are not assembled to the product by
the manufacturer and require customer installation. Use
of a product that may have been improperly assembled
could result in serious personal injury.
WARNING:
 Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
 Do not discard the packing material until you have
carefully inspected the tool, identified all loose parts, and
satisfactorily operated the tool.
NOTE: Remove the foam block from between the saw’s
housing and the motor by first beveling the blade (see
page 28).
 The saw is factory set for accurate cutting. After
assembling it, check for accuracy. If shipping has
influenced the settings, refer to specific procedures
explained in this manual.
 If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
To avoid serious personal injury, always make sure the
table saw is securely mounted to a workbench or an
approved leg stand. NEVER operate the saw on the floor.
Mounting Holes
The table saw must be mounted to a firm supporting surface
such as a workbench or leg stand. Four bolt holes have been
provided in the saw’s base for this purpose. Each of the
four mounting holes should be bolted securely using 1/4 in.
machine bolts, lock washers, and hex nuts (not included).
Bolts should be of sufficient length to accommodate the
saw base, lock washers, hex nuts, and the thickness of the
workbench. Tighten all four bolts securely.
Carefully check the workbench after mounting to make sure
that no movement can occur during use. If any tipping, sliding, or walking is noted, secure the workbench to the floor
before operating.
WARNING:
If any parts are damaged or missing, do not operate
this tool until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
WARNING:
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
16
ASSEMBLY
TO ASSEMBLE THE LEG STAND
See Figure 7.
Assembly is best done in the area where the saw will be used.
If you are unsure about the description of any part, refer to
the drawing. If any parts are missing, delay assembling until
you have obtained the missing part(s).
CARRIAGE
Bolt
upper
brace
Hex
Nut
 Take the following from a small hardware pack:
16 bolts (1/4 - 20 x 1/2 in.)
16 hex nuts (1/4 - 20)
 Take 4 legs and 8 braces from loose parts.
 Place an upper brace inside two of the legs, with the
legs wide end up. (Upper braces have two large holes in
each end.) Make sure the dimples on the leg align with
the small holes on the brace.
upper Side
brace
LEG
Lower
Brace
 Align the large holes on the brace and the legs. Insert
the bolts. Add hex nuts and hand tighten. Repeat for the
other upper brace. These are the front and back sets.
Lower SIDE
Brace
 For the side sets, install an upper side brace on two
legs. Add hardware and finger tighten.
 Use the same steps to install the lower braces. Tighten
all hex nuts securely with the socket wrench.
hex
nut
foot
 Install a foot to the bottom of each leg.
carriage
bolt
Fig. 7
 Move the leg set to desired location.
Mounting THE TABLE saw base ON THE
leg stand
See Figure 8.
 Take the following from a small hardware pack:
4 carriage bolts (1/4-20 x 1-3/8 in.)
4 hex nuts (1/4-20)
Note: This hardware was in the pack with hardware for
assembling the leg stand and leveling feet.
 Place the table saw base on the leg stand. Align the holes
in the table with the holes in the end braces.
 Place a bolt in each hole. Secure with a hex nut. Hand
tighten.
 Repeat for three remaining holes. Tighten all hardware
securely with the socket wrench.
CARRIAGE
Bolt
hex
nut
Fig. 8
17
ASSEMBLY
to install the Handle
See Figure 9.
 Hold the nylon nut securely and turn the screw counterclockwise to remove the nut completely.
NOTE: Do not remove the screw from the handle.
 Place the nylon nut into the recessed hole on the back
of the height/bevel adjusting handwheel and hold in
place.
 Slide the handle, screw, and washer into the hole on the
height/bevel adjusting handwheel.
 Using a flathead screwdriver, turn the screw clockwise
and tighten in place.
Handle
SCREW
TO Install the locking LEVER
See Figure 10.
 Slide the locking lever over the exposed end of the rip
fence making certain the handle is inserted as far as
possible.
WASHER
NYLON
NUT
 Align the holes in the rip fence and the holes in the lever.
Secure using the screws.
HEIGHT/BEVEL
ADJUSTING HANDWHEEL
Fig. 9
locking
LEVER
to remove/replace the THROAT PLATE
See Figure 11.
 Lower the blade by turning the height/bevel adjusting
handwheel counterclockwise.
 To remove the throat plate, place your index finger in
the hole and lift the front end pulling the throat plate out
toward the front of the saw.
 To reinstall the throat plate, slip the tab into the slot at
the back of the saw and push down to secure in place.
SCREWS
rip
fence
Fig. 10
THROAT
PLATE
spreader/ RIVING
KNIFE
Fig. 11
Fig. 11
18
ASSEMBLY
to CHANGE BETWEEN A spreader AND A
riving knife
release lever
(UNLOCKED)
See Figure 12.
This saw is shipped with the spreader/riving knife placed
in the non-through cutting or “down” position (riving knife
position).
NOTE: The spreader/riving knife must be placed in the
through cutting, or “up” position (spreader position), for all
other cutting operations.
 Unplug the saw.
To place in spreader position (or “up” position for all
through cutting):
 Remove the throat plate.
 Raise the saw blade by turning the height/bevel adjusting
handwheel clockwise.
 Unlock the release lever by pulling it up.
 Grasp the spreader and pull it towards the right side of
the saw to release the spreader from the spring-loaded
riving clamp.
 Pull the spreader up until the internal pins are engaged
and the spreader is above the saw blade.
 Lock the release lever by pushing the lever down.
 Reinstall the throat plate.
To place in riving knife position (or “down” position for
all non-through cutting):
 Remove the throat plate.
in “UP” POSITION for through cutting
release lever
(LOCKED)
 Raise the saw blade by turning the height/bevel adjusting
handwheel clockwise.
 Unlock the release lever by pulling it up.
 Push the riving knife down until it is below the saw
blade.
 Lock the release lever by pushing the lever down.
 Reinstall the throat plate.
in “down” position for non-through cutting
Fig. 12
19
ASSEMBLY
TO check SAW BLADE installation
OPEN END blade
wrench
See Figure 13.
caution:
CLOSED END blade
wrench
blade nut
To work properly, the saw blade teeth must point down
toward the front of the saw. Failure to do so could cause
damage to the saw blade, the saw, or the workpiece.
 Unplug the saw.
 Lower the saw blade and remove the throat plate.
 Make sure the bevel locking lever is securely pushed to
the right. Raise the saw blade to its full height by turning
the height/bevel adjusting handwheel clockwise.
 Place spreader/riving knife in “up” position.
To loosen the blade:
 Using the open end blade wrench, place the flat open
end on the flats on the arbor shaft.
 Insert the closed end blade wrench over the blade nut.
Holding both wrenches firmly, pull the closed end wrench
forward to the front of the machine.
To tighten the blade:
 Using the open end blade wrench, place the flat open
end into the flats on the arbor shaft.
 Insert the closed end blade wrench over the blade nut.
Holding both wrenches firmly, push the closed end wrench
to the back of the machine. Make sure the blade nut is
securely tightened. Do not overtighten.
 Reinstall the throat plate.
 Check all clearances for free blade rotation.
Fig. 13
20
ASSEMBLY
TO INSTALL THE BLADE GUARD AND ANTIKICKBACK PAWLS
BLADE
guard
See Figures 14 - 16.
guard
LEVER
WARNING:
Replace dull or damaged anti-kickback pawls. Dull or
damaged pawls may not stop a kickback increasing the
risk of serious personal injury.
NOTE: Anti-kickback pawls should only be installed for
through cuts.
 Unplug the saw.
 Raise the saw blade by turning the height/bevel adjusting
handwheel clockwise.
Fig. 14
 Place spreader/riving knife in “up” position.
pawl
handle
To install blade guard:
 Lift the guard lever up to unlock.
 With the front of the blade guard raised, lower the back
of the guard into the middle hole of the spreader/riving
knife. Push the front of the guard down until it is parallel to the table (see figure 15). If the blade guard is not
parallel to the table, the riving knife is not in the spreader
(or “up”) position.
button
ANTI-KICKBACK
PAWLS
 Lock the guard in place by pushing the guard lever
down.
To install anti-kickback pawls:
 Press and hold the button on the right side of the antikickback pawls.
 Align the slot in the pawls over the rear hole in the spreader/
riving knife.
 Push the pawl handle down snapping them into place
and release the button.
NOTE: Pull on the pawl handle to make sure pawls are
securely locked.
NOTE: Blade alignment with the spreader can be adjusted
for different blade widths. Refer to: To Check and Align the
Spreader/Riving Knife and Saw Blade. Check the blade guard
assembly for clearances and free movement.
Fig. 15
correct
incorrect
21
Fig. 16
ASSEMBLY
TO Check and Align the spreader/riving
knife and Saw Blade
hex key
See Figures 17 - 18.
To check alignment of the spreader/riving knife:
 Unplug the saw.
 Raise the saw blade by turning the height/bevel adjusting
handwheel clockwise.
 Remove the anti-kickback pawls and blade guard
assembly. Place a framing square or straight edge against
both the saw blade and the spreader.
Note: Place framing square between carbide teeth and
measure from blade. This step will insure framing square
is square against blade from the front to back of blade.
 The saw blade and spreader/riving knife are aligned when
the framing square contacts both the blade and spreader/
riving knife evenly with no gaps.
If the spreader/riving knife is out of alignment with the saw
blade, adjustment is needed. The spreader/riving knife must
be in alignment front to back (horizontally) and top to bottom (vertically).
SPREADER/
riving knife
framing
square
Fig. 17
HORIZontAL ADJUSTMENT
To adjust (horizontally):
 Remove the blade guard assembly and anti-kickback
pawls.
 Raise the blade to its full height.
 Insert the hex key through the slot on the back of the
saw. Two adjustment screws can be accessed through
the slot.
 Turn the adjustment screws to reposition the spreader/
riving knife left or right as needed to align the spreader/
riving knife with the saw blade.
 Once properly aligned, securely retighten the screws.
To adjust (vertically):
 Push either side of the riving knife to align it top to bottom with the blade. Check its position after adjustment
to ensure that it is vertically aligned with the blade.
FRAMING
SQUARE
SPREADER/
riving knife
blade
VERTICAL ADJUSTMENT
FRAMING
SQUARE
SPREADER/
riving knife
blade
Fig. 18
22
ASSEMBLY
PUSH STICK STORAGE
push stick storage
SCREW(S)
See Figure 19.
 Insert the push stick storage screws from the loose parts
bag into the holes on the side of the saw table. Use a
Phillips head screwdriver to tighten screws securely.
 Place the slots in the push stick over the screws and slide
the push stick toward the back of the saw.
PUSH STICK
Fig. 19
23
OPERATION
from the workpiece and may contact the blade. Kickback can
cause serious injury. Use precautions to avoid the risks.
Kickback can be caused by any action that pinches the
blade in the wood such as:
WARNING:
Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is sufficient to inflict severe injury.











WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes, resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this tool. The use
of attachments or accessories not recommended can
result in serious personal injury.
Making a cut with incorrect blade depth
Sawing into knots or nails in the workpiece
Twisting the wood while making a cut
Failing to support work
Forcing a cut
Cutting warped or wet lumber
Using the wrong blade for the type of cut
Not following correct operating procedures
Misusing the saw
Failing to use the anti-kickback pawls
Cutting with a dull, gummed-up, or improperly set
blade
AVOIDING KICKBACK
 Always use the correct blade depth setting. The top of
the blade teeth should clear the workpiece by 1/8 in. to
1/4 in.
 Inspect the work for knots or nails before beginning a
cut. Knock out any loose knots with a hammer. Never
saw into a loose knot or nail.
 Always use the rip fence when rip cutting. Use the miter
gauge when cross cutting. This helps prevent twisting
the wood in the cut.
 Always use clean, sharp, and properly-set blades. Never
make cuts with dull blades.
 To avoid pinching the blade, support the work properly
before beginning a cut.
 When making a cut, use steady, even pressure. Never
force cuts.
 Do not cut wet or warped lumber.
 Use extra caution when cutting some prefinished or
composition wood products as the anti-kickback pawls
may not always be effective.
 Always guide your workpiece with both hands or with
push sticks and/or push blocks. Keep your body in a
balanced position to be ready to resist kickback should
it occur. Never stand directly in line with the blade.
 Use of a featherboard will help hold the workpiece securely
against the saw table or fence.
 Clean the saw, blade guard, under the throat plate, and any
areas where saw dust or scrap workpieces may gather.
 Use the right type of blade for the cut being made.
 Always use the spreader / riving knife for every operation
where it is allowed. The use of this device will greatly
reduce the risk of kickback.
WARNING:
Although many of the illustrations in this manual are
shown with the blade guard removed for clarity, do not
operate the saw without the blade guard unless specifically instructed to do so.
APPLICATIONS
You may use this tool for the purposes listed below:
 Straight line cutting operations such as cross cutting,
ripping, mitering, beveling, and compound cutting
 Cabinet making and woodworking
NOTE: This table saw is designed to cut wood and wood
composition products only. It is not designed for cutting large
panels. Depending on the shape of the panel, use the rip
fence or miter gauge. If the panel is too large to use either
the rip fence or the miter gauge, it is too large for this saw.
Basic Operation of the TABLE Saw
The 3-prong plug must be plugged into a matching outlet
that is properly installed and grounded according to all local
codes and ordinances. Improper connection of the equipment can result in electric shock. Do not modify the plug if
it will not fit the outlet. Have the correct outlet installed by
a qualified electrician. Refer to the Electrical section in this
manual.
CAUSES OF KICKBACK
Kickback can occur when the blade stalls or binds, kicking
the workpiece back toward you with great force and speed. If
your hands are near the saw blade, they may be jerked loose
24
OPERATION
cutting aids
See Figure 20.
Push sticks are devices that may be used for pushing a
workpiece through the blade in any rip cut. When making
non-through cuts or ripping narrow stock, always use a
push stick, push block, and/or featherboard so your hands
do not come within 3 inches of the saw blade. They can be
made in various sizes and shapes from scrap wood and
used in a specific project. The stick must be narrower than
the workpiece, with a 90˚ notch in one end and shaping for
a grip on the other end.
A push block has a handle fastened by recessed screws
from the underside. Use push blocks for narrow cuts and
all non-through cuts.
PUSH STICKS
PUSH BLOCKS
CAUTION:
Fig. 20
Be sure the screws in a push block are recessed to avoid
damaging the saw or workpiece.
AUXILIARY FENCE
An auxiliary fence is a device used to close the gap between
the rip fence and the saw table. Always make and use and
auxiliary fence when ripping material 1/8 in. or thinner.
How to Make and ATTACH an auxiliary
fence (for rip cutting thin
workpiece)
18 1/2 in.
18-1/2
in.
See Figure 21.
Rip fence holes are used to secure an auxiliary fence which
requires a piece of wood 3/4 in. thick, 3-1/2 in. wide, and
18-1/2 in. long to make.
4 1/4 3-1/2
in.
in.
in.
3/41/2in.
Fig. 21
To attach the auxiliary fence to the rip fence:
 Place the wood against the rip fence and resting firmly
on the saw table.
 From the back side of the rip fence, secure the wood to
the fence using 1-1/2 in. wood screws.
STOP
jig
handle
How to Make a jig (for rip cutting
narrow workpiece)
See Figure 22.
If ripping a narrow workpiece places the hands too close to
the blade, it will be necessary to make and use a jig.
jig
To make a jig:
 Attach a handle to a long, straight piece of wood and
secure from the underside using recessed screws.
 Cut an L-shaped stop in the side of the jig.
To use a jig:
 Position the workpiece flat on the table with the edge
flush against the jig and against the stop.
 Holding the jig handle and using a push block, make the
rip cut as described on page 33 later in this section.
Fig. 22
25
OPERATION
FEATHERBOARD
WARNING:
A featherboard is a device used to help control the
workpiece by holding it securely against the table or fence.
Featherboards are especially useful when ripping small
workpieces and for completing non-through cuts. The end
is angled with a number of short kerfs to give a friction hold
on the workpiece and locked in place on the table with a
C-clamp. Test to ensure it can resist kickback.
Mount the featherboard in front of the saw blade. If
positioned improperly, kickback can result from the
featherboard pinching the workpiece and binding the
blade in the saw kerf. Failure to heed this warning can
result in serious personal injury.
HOW TO MOUNT A FEATHERBOARD
HOW TO MAKE A FEATHERBOARD
See Figure 24.
Completely lower the saw blade. Position the rip fence to
the desired adjustment for the cut to be performed and lock.
Place the workpiece against the fence and over the saw
blade area. Adjust the featherboard to apply resistance to
the workpiece just forward of the blade. Securely tighten the
adjusting clamp knob to secure the featherboard in place.
Attach C-clamps to further secure the featherboard to the
edge of the saw table.
See Figure 23.
The featherboard is an excellent project for the saw.
Select a solid piece of lumber approximately 3/4 in. thick,
2-1/2 in. wide and 12 in. long. Mark the center of the width
on one end of the stock. Miter the width to 70° (see page
33 for information on miter cuts).
Prepare the saw for ripping as discussed on page 33. Set
the rip fence to allow approximately a 1/4 in. “finger” to be
cut in the stock. Feed the stock only to the mark previously
made at 6 in. Turn the saw Off and allow the blade to completely stop rotating before removing the stock. Reset the
rip fence and cut spaced rips into the workpiece to allow
approximately 1/4 in. fingers and 1/8 in. spaces between
the fingers.
push block
featherboard
push
stick
Bevel
Locking
Lever
Fig. 24
2 1/2 in.
1/4 in.
70°
1/8 in.
3/4 in.
4 in.
12 in.
Fig. 23
26
operation
types of cuts
See Figure 25.
There are six basic cuts: 1) the cross cut, 2) the rip cut, 3)
the miter cut, 4) the bevel cross cut, 5) the bevel rip cut, and
6) the compound (bevel) miter cut. All other cuts are combinations of these basic six. Operating procedures for making
each kind of cut are given later in this section.
1
Cross Cut
WARNING:
Always make sure the blade guard and anti-kickback
pawls are in place and working properly when making
these cuts to avoid possible injury.
2
Rip Cut
Cross cuts are straight 90° cuts made across the grain of
the workpiece. The wood is fed into the cut at a 90° angle
to the blade, and the blade is vertical.
3
Rip cuts are made with the grain of the wood. To avoid
kickback while making a rip cut, make sure one side of the
wood rides firmly against the rip fence.
Miter Cut
Miter cuts are made with the wood at any angle to the
blade other than 90°. The blade is vertical. Miter cuts tend
to “creep” during cutting. This can be controlled by holding
the workpiece securely against the miter gauge.
4
Bevel cuts are made with an angled blade. Bevel cross cuts
are across the wood grain, and bevel rip cuts are with the
grain.
Bevel Cross Cut
Compound (or bevel) miter cuts are made with an angled
blade on wood that is angled to the blade. Be thoroughly
familiar with making cross cuts, rip cuts, bevel cuts, and
miter cuts before trying a compound miter cut.
5
CUTTING TIPS
Rabbet cuts are non-through cuts which can be either rip
cuts or cross cuts. Carefully read and understand all sections
of this operator’s manual before attempting any operation.
Bevel Rip Cut
WARNING:
6
Do not use blades rated less than the speed of this tool.
Failure to heed this warning could result in personal
injury.
Compound (bevel) Miter Cut
 The kerf (the cut made by the blade in the wood) will be
wider than the blade to avoid overheating or binding.
Make allowance for the kerf when measuring wood.
 Make sure the kerf is made on the waste side of the
measuring line.
 Cut the wood with the finish side up.
 Knock out any loose knots with a hammer before making
the cut.
 Always provide proper support for the wood as it comes
out of the saw.
Fig. 25
27
operation
TO CHANGE BLADE DEPTH
gullet
See Figure 26.
The blade depth should be set so that the outer points of
the blade are higher than the workpiece by approximately
1/8 in. to 1/4 in. but the lowest points (gullets) are below
the top surface.
 Turn the bevel lock lever to the right.
 Raise the blade by turning the height/bevel adjusting
handwheel clockwise or lower it by turning the handwheel
counterclockwise.
Fig. 26
TO CHANGE BLADE ANgle (BEVEL)
90º adjustment
SCREW
See Figure 27.
This table saw has a rack and pinion bevel control that allows
you to make angled cuts from 90° to 45°.
Note: A 90° cut has a 0° bevel and a 45° cut has a 45°
bevel.
 Unplug the saw.
45º adjustment
SCREW
bevel
locking
lever
 Loosen bevel control by turning bevel lock lever all the
way to the left. If it needs to be further loosened, pull
spring-loaded bevel lock lever out and rotate it back to
the right. Release bevel locking lever and allow it to seat
(lock) in its original position. Turn it to the left again until
loose.
height/bevel
adjusting
handWHEEL
 Move the height adjusting handwheel to the right to bevel
to 45° bevel angle.
 Tighten bevel control by turning bevel lock lever to the
right. If it needs to be tightened more, pull the springloaded bevel lock lever out and rotate it to the left. Then
release bevel lock lever and allow it to return to its original
position. Rotate to the right again. Repeat this process
until bevel lock lever is securely tightened.
TO DECREASE
ANGLE
TO INCREASE
ANGLE
Fig. 27
To Adjust the Bevel indicator
See Figure 28.
COMBINATION
SQUARE
If the bevel indicator is not at zero when the saw blade is at
90°, adjust the indicator by loosening the screw and setting
it at 0° on the bevel scale. Retighten the screw.
height/bevel
adjusting
handWHEEL
screw
28
BEVEL
LOCKING
LEVER
bevel
indicator
Fig. 28
operation
WARNING:
clamp
screw
To reduce the risk of injury, always make sure the rip fence
is parallel to the blade before beginning any operation.
locking
lever
TO use the Rip Fence
See Figure 29.
 Place the rear lip on the rear of the saw table and pull
slightly toward the front of the unit.
 Lower the front end of the rip fence onto the guide
surfaces on top of the front rail.
 With the rip fence flat on the saw table, push the fence
towards the front rail to align the fence to the saw
table.
 Push the locking lever down to align and secure the
fence.
Check for a smooth gliding action. If adjustments are needed,
see To Check the Alignment of the Rip Fence to the Blade
in the Adjustment section of this manual.
rip
fence
REAR
LIP
 Make two or three test cuts on scrap wood. If the cuts
are not true, repeat the process.
NOTE: The rip fence must be secure when the locking
handle is engaged. To increase the grip of the rip fence
on the rear lip of the table, tighten the clamp screw on
the rear of the rip fence by turning it clockwise.
Rip
fence
Blade
Scale
To Set the rip fence Scale indicator
to the Blade
See Figure 29.
Use the indicator on the rip fence to position the fence along
the scale on the front rail.
Note: The anti-kickback pawls and blade guard assembly
must be removed to perform this adjustment. Reinstall the
blade guard assembly when the adjustment is complete.
2 in.
Begin with the blade at a zero angle (straight up).
 Unplug the saw.
 Loosen the rip fence by lifting the locking lever.
 Using a framing square, set the rip fence 2 in. from the
blade tip edge.
 Loosen the screw on the scale indicator and align with
the 2 in. mark as shown.
 Tighten the screw and check the dimension and the rip
fence.
2 in.
mark
29
Scale
indicator
Locking
lever
Front
rail
Fig. 29
operation
TO use the miter gauge
See Figure 30.
The miter gauge provides greater accuracy in angled cuts.
For very close tolerances, test cuts are recommended.
MITER
GAUGE BODY
There are two miter gauge grooves, one on either side of
the blade. When making a 90° cross cut, you can use either
miter gauge groove. When making a beveled cross cut (the
blade tilted in relation to the table) the miter gauge should be
located in the groove on the right so that the blade is tilted
away from the miter gauge and your hands.
LOCK
KNOB
MITER
GAUGE
The miter gauge can be turned 60° to the right or left.
Fig. 30
 Loosen the lock knob.
 With the miter gauge in the miter gauge groove, rotate the
gauge until the desired angle is reached on the scale.
 Retighten the lock knob.
MITER GAUGE
reversed
TO use the miter gauge in a reverse
position
See Figure 31.
For larger workpieces, the miter gauge can be reversed in
the miter gauge grooves. It will be necessary when reversing the miter gauge to clamp the workpiece to the miter
gauge body.
Fig. 31
30
operation
heeling (paralleling) the blade to the
miter gauge groove
See Figures 32 - 34.
adjusting
SCREWS
WARNING:
RIGHT MITER
gauge GROOVE COMBINATION
SQUARE
The blade must be parallel to the miter gauge groove so
the wood does not bind resulting in kickback. Failure to
do so could result in serious personal injury.
Do not loosen any screws for this adjustment until you
have checked with a square and made test cuts to be sure
­adjustments are necessary. Once the screws are loosened,
these items must be reset.
 Unplug the saw.
 Remove the blade guard and anti-kickback pawls.
Raise the blade by turning the height/bevel adjusting
handwheel.
 Mark beside one of the blade teeth at the front of the
blade. Place a combination square even with the front
of the saw table and the side of the saw blade as shown
in figure 32.
 Turn the blade so the marked tooth is at the back.
 Move the combination square to the rear and again
measure the distance. If the distances are the same, the
blade is square.
If the distances are different:
 Place spreader/riving knife in “down” position.
 Loosen the adjusting screws, located on top of the saw
table.
NOTE: If the back of the blade was too far from the combination square, place a block of wood on the left side
of the blade and push it into the blade until the blade is
square. Retighten the screws.
If the back of the blade was too close to the combination
square, place a block of wood on the right side of the blade
and push it into the blade until the blade is square.
 Retighten the screws.
adjusting
SCREWS
Fig. 32
COMBINATION
SQUARE
Fig. 33
WARNING:
To reduce the risk of injury from kickback, align the rip
fence to the blade following any blade adjustments.
Always make sure the rip fence is parallel to the blade
before beginning any operation.
BLADE TOO CLOSE TO MITER GAUGE GROOVE
Fig. 34
31
operation
MAKING CUTS
CROSS CUT
This table saw can perform a variety of cuts that are not all
mentioned in this manual. DO NOT attempt to make any cuts
not covered here unless you are thoroughly familiar with the
proper procedures and necessary accessories. Your local
library has many books on table saw usage and specialized
woodworking procedures for your reference.
PLACE right HAND ON
MITER Gauge HERE
The blade provided with the saw is a high-quality combination blade suitable for ripping and cross cut operations. Carefully check all setups and rotate the blade one full revolution
to assure proper clearance before connecting saw to power
source. Stand slightly to the side of the blade path to reduce
the chance of injury should kickback occur.
WARNING:
Do not use blades rated less than the speed of this tool.
Failure to heed this warning could result in personal
injury.
Fig. 35
Use the miter gauge when making cross, miter, bevel, and
compound miter cuts. To secure the angle, lock the miter
gauge in place by twisting the lock knob clockwise. Always
tighten the lock knob securely in place before use.
SWITCH
OFF
SWITCH
ON
NOTE: It is recommended that you place the piece to be
saved on the left side of the blade and that you make a test
cut on scrap wood first.
MAKING a cross cut
See Figures 35 - 36.
WARNING:
Make sure the blade guard assembly is installed and
working properly to avoid serious possible injury.
SWITCH KEY
WARNING:
Using the rip fence as a cutoff gauge when cross cutting
will result in kickback which can cause serious personal
injury.
 Remove the rip fence.
 Set the blade to the correct depth for the workpiece.
SWITCH IN LOCKED POSITION
 Set the miter gauge to 0° and tighten the lock knob.
 Make sure the wood is clear of the blade before turning
on the saw.
 Turn the saw on.
 Let the blade build up to full speed before moving the
workpiece into the blade.
 Hold the workpiece firmly with both hands on the miter
gauge and feed the workpiece into the blade.
Fig. 36
Note: The hand closest to the blade should be placed
on the miter gauge lock knob and the hand farthest from
the blade should be placed on the workpiece.
 When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
32
operation
making a RIP cut
RIP CUT
See Figure 37.
BLADE
RIP
FENCE
WARNING:
Make sure the blade guard assembly is installed and
working properly to avoid serious possible injury.
 Set the blade to the correct depth for the workpiece.
 Position the rip fence the desired distance from the blade
for the cut and securely lock the handle.
 Make sure the wood is clear of the blade before turning
on the saw.
 When ripping a long workpiece, place a support the same
height as the table surface behind the saw for the cut
work.
 Turn the saw on.
 Position the workpiece flat on the table with the edge
flush against the rip fence. Let the blade build up to full
speed before feeding the workpiece into the blade.
 Once the blade has made contact with the workpiece, use
the hand closest to the rip fence to guide it. Make sure
the edge of the workpiece remains in solid contact with
both the rip fence and the surface of the table. If ripping
a narrow piece, use a push stick and/or push blocks to
move the piece through the cut and past the blade.
 When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
SCALE
Fig. 37
MITER Gauge
ANGLED
MITER CUT
BLADE
STRAIGHT
making a miter cut
See Figure 38.
WARNING:
Make sure the blade guard assembly is installed and
working properly to avoid possible serious injury.
 Remove the rip fence.
 Set the blade to the correct depth for the workpiece.
 Set the miter gauge to the desired angle and tighten the
lock knob.
 Make sure the wood is clear of the blade before turning
on the saw.
 Turn the saw on.
 Let the blade build up to full speed before moving the
workpiece into the blade.
 Hold the workpiece firmly with both hands on the miter
gauge and feed the workpiece into the blade.
NOTE: The hand closest to the blade should be placed
on the miter gauge lock knob and the hand farthest from
the blade should be placed on the workpiece.
Fig. 38
 When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
33
operation
making a bevel cross cut
VIEWED FROM THE FRONT, BELOW THE TABLE SAW
See Figures 39 - 40.
TO LOOSEN
WARNING:
TO
TIGHTEN
Make sure the blade guard assembly is installed and
working properly to avoid possible serious injury.







Remove the rip fence.
Unlock the bevel locking lever.
Adjust the bevel angle to the desired setting.
Lock the bevel locking lever.
Set the blade to the correct depth for the workpiece.
Set the miter gauge to 0° and tighten the lock knob.
Make sure the wood is clear of the blade before turning
on the saw.
Bevel
LOCKING LEVER
 Turn the saw on.
 Let the blade build up to full speed before moving the
workpiece into the blade.
 Hold the workpiece firmly with both hands on the miter
gauge and feed the workpiece into the blade.
NOTE: The hand closest to the blade should be placed
on the miter gauge lock knob and the hand farthest from
the blade should be placed on the workpiece.
 When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
height/bevel
ADJUSTING
HANDWHEEL
Fig. 39
BEVEL CROSS CUT
making a bevel rip cut
BLADE ANGLED
See Figure 41.
MITER Gauge
STRAIGHT
WARNING:
Make sure the blade guard assembly is installed and
working properly to avoid serious personal injury.
WARNING:
The rip fence must be on the right side of the blade to
avoid trapping the wood and causing kickback. Placement of the rip fence to the left of the blade will result in
kickback and the risk of serious personal injury.
 Remove the miter gauge.





Fig. 40
Unlock the bevel locking lever.
Adjust the bevel angle to 0º.
Lock the bevel locking lever.
Set the blade to the correct depth for the workpiece.
Position the rip fence the desired distance from the blade
for the cut and securely lock the handle.
 Make sure the wood is clear of the blade before turning
on the saw.
 When ripping a long workpiece, place a support the same
height as the table surface behind the saw for the cut
work.
 Turn the saw on.
34
operation
 Position the workpiece flat on the table with the edge
flush against the rip fence. Let the blade build up to full
speed before feeding the workpiece into the blade.
BEVEL RIP CUT
RIP FENCE
BLADE
ANGLED
 Once the blade has made contact with the workpiece, use
the hand closest to the rip fence to guide it. Make sure
the edge of the workpiece remains in solid contact with
both the rip fence and the surface of the table. If ripping
a narrow piece, use a push stick and/or push blocks to
move the piece through the cut and past the blade.
 When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
SCALE
making a compound (bevel) miter cut
See Figure 42.
WARNING:
Make sure the blade guard assembly is installed and
working properly to avoid possible serious injury.
Fig. 41
 Remove the rip fence.
 Unlock the bevel locking lever.
COMPOUND (BEVEL) MITER CUT
 Adjust the bevel angle to the desired setting.
PLACE left HAND ON Miter
gauge HERE
 Lock the bevel locking lever.
 Set the blade to the correct depth for the workpiece.
 Set the miter gauge to the desired angle and tighten the
lock knob.
 Make sure the wood is clear of the blade before turning
on the saw.
 Turn the saw on.
 Let the blade build up to full speed before moving the
workpiece into the blade.
 Hold the workpiece firmly with both hands on the miter
gauge and feed the workpiece into the blade.
NOTE: The hand closest to the blade should be placed
on the miter gauge lock knob and the hand farthest from
the blade should be placed on the workpiece.
 When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
Fig. 42
35
operation
making a NON-THROUGH cut
NON-THROUGH CUT
See Figure 43.
BLADE GUARD
REMOVED
WARNING:
DO NOT install dado blades on this machine. The arbor
shaft has insufficient threads to mount a dado blade.
Mounting a dado blade could result in the risk of serious
personal injury.
Non-through cuts (made with a standard 10 in. blade) can be
made with the grain (ripping) or across the grain (cross cut).
The use of a non-through cut is essential to cutting grooves.
DO NOT perform bevel non-through cuts on this machine.
PUSH
STICK
This is the only type cut that is made without the blade guard
assembly installed. Make sure the blade guard assembly is
reinstalled upon completion of this type of cut.
Read the appropriate section which describes the type of
cut in addition to this section on non-through cuts. For example, if your non-through cut is a straight cross cut, read
and understand the section on straight cross cuts before
proceeding.
Fig. 43
 Set the blade to the correct depth for the workpiece.
 Depending on the shape and size of the wood, use either
the rip fence or miter gauge.
 Plug the saw into the power source and turn the saw
on.
 Let the blade build up to full speed before moving the
workpiece into the blade.
 Always use push blocks, push sticks, and/or featherboards
when making non-through cuts to reduce the risk of serious injury.
 When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
Once all non-through cuts are completed:
Unplug your saw.
 Reinstall the spreader/riving knife in the “up” position
then install the blade guard and anti-kickback pawls.
WARNING:
When making a non-through cut, the blade is covered
by the workpiece during most of the cut. Be alert to the
exposed blade at the start and finish of every cut to reduce the risk of personal injury.
WARNING:
Never feed wood with your hands when making any nonthrough cut such as rabbets. To avoid personal injury, always use push blocks, push sticks, and featherboards.






Unplug the saw.
Remove the blade guard and anti-kickback pawls.
Place spreader / riving knife in “down” position.
Unlock the bevel locking lever.
Adjust the bevel angle to 0º
Lock the bevel locking lever.
36
ADJUSTMENTS
WARNING:
closed end
blade
WRENCH
OPEN END
blade
WRENCH
Before performing any adjustment, make sure the tool is
unplugged from the power supply and the switch is in the
OFF position. Failure to heed this warning could result in
serious personal injury.
The table saw has been adjusted at the factory for making
very accurate cuts. However, some of the components might
have been jarred out of alignment during shipping. Also,
over a period of time, readjustment will probably become
necessary due to wear.
To avoid unnecessary set-ups and adjustments, a good practice is to check your setups carefully with a framing square
and make practice cuts in scrap wood before making finish
cuts in good workpieces. Do not start any adjustments until
you have checked with a square and made test cuts to be
sure adjustments are needed.
Fig. 44
Blade
arbor
shaft
TO REPLACe THE BLADE
See Figures 44 - 46.
 Unplug the saw.
 Remove the blade guard and anti-kickback pawls.
 Lower the saw blade and remove the throat plate.
 Make sure the bevel locking lever is locked.
 Raise the saw blade to full height.
 Insert the open end blade wrench onto the flats on the
arbor shaft.
 Insert the closed end blade wrench over the blade nut.
Holding both wrenches firmly, pull the closed end wrench
(right side) forward while pushing the open end wrench
(left side) to the back of the saw. Remove the nut.
 Unlock the release locking lever and remove the blade.
To install a standard blade:
 Place the new blade on the arbor shaft (the teeth
must point down toward the front of the saw to work
properly).
 Place the blade washer and the blade nut over the arbor
shaft. Be sure the dome side of the blade washer faces
the blade and that all items are snug against the arbor
housing. Make sure the blade nut is securely tightened.
Do not overtighten.
 Lock the release lever.
 Rotate the blade by hand to make sure it turns freely.
 Lower the saw blade and reinstall the throat plate.
Blade
washer
Blade
nut
Fig. 45
THROAT
PLATE
spreader /
riving knife
BLADE
NOTE: To replace the blade with an accessory blade, follow
the instructions provided with the accessory.
Fig. 46
37
ADJUSTMENTS
TO SET the blade at 0° and 45°
0° adjustment
screw
See Figures 47 - 49.
The angle settings of the saw have been set at the factory
and, unless damaged in shipping, should not require setting during assembly. After extensive use, they may need
to be checked.
45° adjustment
SCREW
 Unplug the saw.
 Raise the blade.
If the blade is not perfectly vertical (0°):
 Loosen the adjustment screw and the bevel locking
lever.
 Place a combination square beside the blade on the left.
Lock the angle by pushing the bevel locking lever down
and retighten the adjustment screw.
Fig. 47
 Turn the handle until the bevel indicator points to zero.
If the handle is turned as far as possible and doesn’t
indicate zero properly, you may need to adjust the bevel
indicator.
BEVEL
handle
COMBINATION
SQUARE
BLADE
0°
NOTE: It will be necessary to remove the handle to adjust
the bevel indicator.
If the blade is not an exact 45°:
 Loosen the adjustment screw and the bevel locking
lever.
 Place a combination square beside the blade on the
left.
BEVEL
LOCKING
LEVER
 Turn the handle until the bottom of the blade has moved
completely to the left side of the slot. Lock the angle by
pushing the bevel locking lever.
BEVEL
INDICATOR
 If the blade is not an exact 45°, loosen the 45° adjustment
screw and the bevel locking lever.
Fig. 48
 Adjust the bevel indicator to 45°.
BLADE
 Make a test cut.
COMBINATION
SQUARE
45°
BEVEL
LOCKING
LEVER
BEVEL
INDICATOR
BEVEL
HANDLE
38
Fig. 49
ADJUSTMENTS
TO CHECK THE ALIGNMENT OF THE RIP FENCE
TO THE BLADE
framing
square
See Figure 50.
 Unplug the saw.
 Raise the locking lever to permit the rip fence to be
moved.
 Place a framing square beside the blade and move the
rip fence up to the square. Take the dimension on the rip
scale.
 Move the fence back and turn the framing square 180°
to check the other side.
 If the two dimensions are not the same, loosen the two
bolts on the fence and align it.
 Retighten the two bolts.
 Make two or three test cuts on scrap wood. If the cuts
are not true, repeat the process.
rip fence
blade
locking
lever
BOLTS
Fig. 50
MAINTENANCE
WARNING:
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken, or
destroy plastic which may result in serious personal
injury.
WARNING:
 Periodically check all clamps, nuts, bolts, and screws for
tightness and condition. Make sure the throat plate is in
good condition and in position.
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
 Check the blade guard assembly.
 To maintain the table surfaces, fence, and rails,
periodically apply paste wax to them and buff to provide
smooth functioning.
WARNING:
Before performing any maintenance, make sure the tool
is unplugged from the power supply and the switch is in
the off ( O ) position. Failure to heed this warning could
result in serious personal injury.
 Protect the blade by cleaning out sawdust from
underneath the table and in the blade teeth. Use a resin
solvent on the blade teeth.
 Clean plastic parts only with a soft damp cloth. DO
NOT use any aerosol or petroleum solvents.
GENERAL MAINTENANCE
LUBRICATION
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrication is required.
39
TROUBLESHOOTING
Problem
Cause
Solution
Blade is out of balance.
Replace blade.
Blade is damaged.
Replace blade.
Saw is not mounted securely.
Tighten all hardware.
Work surface is uneven.
Reposition on flat surface.
Blade is warped.
Check saw blade installation. Replace blade if
necessary.
Rip fence not mounted correctly.
Remount the rip fence.
Rails are dirty or sticky.
Clean and wax rails.
Clamp screw is out of adjustment.
Adjust clamp screw counterclockwise.
Rip fence does not lock at
rear.
Clamp screw is out of adjustment.
Adjust clamp screw clockwise.
Cutting binds or burns work.
Blade is dull.
Replace or sharpen blade.
Blade is heeling.
See page 31 on "Heeling the Blade".
Work is fed too fast.
Slow the feed rate.
Rip fence is misaligned.
Align the rip fence.
Wood is warped.
Replace the wood. Always cut with convex
side to table surface.
Spreader is out of alignment.
See “To check and align the spreader/riving knife
and saw blade” in the Assembly section.
Blade not properly sharpened or set.
Resharpen or set blade.
Excess vibration.
Rip fence does not move
smoothly.
Wood edges away from rip
fence when ripping.
40
Troubleshooting
Problem
Saw does not make accurate
90˚ or 45˚ cuts.
Cause
Solution
Positive stops inside cabinet need
adjusting (Bevel Cuts).
Adjust positive stops.
Miter gauge is misaligned (Miter
Cuts).
Adjust the miter gauge.
Height/bevel adjusting handwheel is hard to turn.
Gears or screw post inside
cabinet are clogged with saw
dust.
Clean the gears or screw post.
Saw does not start.
Motor cord or wall cord is not
plugged in.
Plug in motor cord or wall cord.
Circuit fuse is blown.
Replace circuit fuse.
Circuit breaker is tripped.
Reset circuit breaker.
Cord or switch is damaged.
Have the cord or switch replaced at your
nearest authorized service center.
Blade is dull or dirty.
Clean, sharpen, or replace blade.
Blade is wrong type for cut being
made.
Replace with correct type.
Blade is mounted backwards.
Remount blade.
Blade does not lower when
turning height/bevel adjusting
handwheel.
Locking lever is not at full left
position.
Move locking lever to left.
Motor labors in rip cut.
Blade not proper for rip cut.
Change blade; rip blade typically has fewer
teeth.
Blade makes poor cuts.
41
OPERATOR’S MANUAL
10 in. Table Saw
RTS10
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
•lead from lead-based paints,
•crystalline silica from bricks and cement and other masonry products, and
•arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specially designed to filter out microscopic
particles.
• Parts and Service
Prior to requesting service or purchasing replacement parts, please obtain your model
and serial number from the product data plate.
•
MODEL NUMBER
•
SERIAL NUMBER
RTS10
• How to obtain Replacement Parts:
Replacement parts can be purchased online at www.ryobitools.com or by calling
1-800-525-2579. Replacement parts can also be obtained at one of our Authorized
Service Centers.
• How to locate an Authorized Service Center:
Authorized Service Centers can be located online at www.ryobitools.com or by calling
1-800-525-2579.
• How to obtain Customer or Technical Support:
To obtain Customer or Technical Support please contact us at 1-800-525-2579.
RYOBI® is a registered trademark of Ryobi Limited used under license.
ONE WORLD TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson, SC 29625
Phone 1-800-525-2579
www.ryobitools.com
987000-864
1-18-10 (REV:05)
42
Download PDF