Vitalinq | 94A-07 | Installation manual | Vitalinq 94A-07 Installation manual

TM
by VIS-A-VIS, INC.
7936 Camino Circle
Miami, FL 33143
support@vitalinq.com
(800) 319-6014
Operations and Installation Manual
Vitalinq Communication System
Model 94A-07
CDX-GT565UP
Symbols and Conventions
This icon identifies cautions: information that should be read
before use to prevent damage to the VitalinqTM system.
Trademark and Other Information
SiriusXM subscriptions and Satellite Radio Tuner module sold separately.
www.siriusxm.com.
Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. and its subsidiaries.
All other marks and logos are the property of their respective owners. All rights reserved.
ZAPPIN and Quick-BrowZer are trademarks of Sony Corporation.
Windows Media is either a registered trademark or trademark of Microsoft Corporation in the
United States and/or other countries.
This product contains technology subject to certain intellectual property rights of Microsoft. Use or
distribution of this technology outside of this product is prohibited without the appropriate license(s)
from Microsoft.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the
U.S. and other countries.
VitalinqTM System Specifications
Input Ratings:100-220V~
50-60Hz
1.6A MAX
Operating Temperature: 25˚C (77˚F)
Stereo Power Amplifier Specifications
Output: Speaker outputs
Speaker impedance: Only use with provided 8 ohm speakers
Maximum power output: 8W × 4 (with Vis-A-Vis provided 8 ohm speakers)
For Your Safety
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8.
Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete
outlet.
10.
Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11.
Only use attachments/accessories specified by the manufacturer.
12.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13.
Unplug this apparatus during lightning storms or when unused for long periods of time.
14.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
15.
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
16.
A warning that excessive sound pressure from earphones and headphones can cause hearing
loss.
Table of Contents
1
1.1
Vitalinq™ introduction
System Layout
2
2.1
2.2
2.3
2.4
Setting up the Vitalinq™ system
Description of the Vitalinq™ system
Initial Settings
Adjusting the Headset
Adjusting the Overhead Controls
3
3.1
3.2
Vitalinq™ operating instructions
Initial operation of the headset
Initial operation of the overhead speaker and desk microphone
4
Music system operation
4.1
Getting started
4.1.1 Music system power
4.2
Adjusting setup items
4.2.1 Canceling the DEMO mode
4.2.2 Setting the clock
4.2.3 Additional setup items 4.3
Location of controls & basic operations
4.4Radio
4.4.1 Storing and receiving stations
4.4.2RDS
4.5
CD Functions
4.5.1 Playing a disc
4.6
USB devices
4.6.1 Playing back a USB device
4.7iPod
4.7.1 Playing back a iPod device
4.7.2 Operating an iPod directly
4.8
Pandora® via USB (iPhone)
4.8.1 Playing back Pandora via the USB connector
4.9
Searching and playing tracks
4.9.1 Playing tracks in various modes
4.9.2 Searching a track by name - Quick-BrowZer™
4.9.3 Searching a track by listening to track passages
ZAPPIN™
4.10 Changing the illumination
4.10.1 Changing the color of display and buttons
4.10.2 Advanced color settings
4.11 Sound Settings and Setup Menu
4.11.1 Changing the sound settings
4.11.2 Customizing the equalizer curve - EQ7 Setting
4.12 Auxiliary audio equipment
4.12.1 Connecting the portable audio device
4.12.2 Sirius XM Tuner
4.13 Additional information
4.13.1 Notes on discs
4.13.2 Playback order of MP3/WMA/ AAC files
4.13.3 About iPod
4.13.4 Safety Precautions
5
5.1
5.2
Troubleshooting guide
Communication Troubleshooting Guide
Music Troubleshooting Guide
6
6.1
6.2
6.3
Planning the Vitalinq™ Installation
Procedure room (LAB)
Control room (TEK)
Control room console
7
7.1
7.2
7.3
Installing Vitalinq™ ceiling devices
Installing ceiling devices
Monitor mounted microphone - MM-5
Connection options
Monitor mounted microphone - placement
8
8.1
8.2
Installing the Vitalinq™ console
Front of console
Rear of console
We would like to hear from you. Our phone number is 1-800-319-6014, or email us at support@vitalinq.com.
Please visit us on the web at http://www.vitalinq.com.
We are very interested in helping you to solve any problems or answer any questions you may have with the
operation or installation.
Please call and give us the name and address of the hospital, cath lab phone number and name of the cath lab
director or manager so that we can better serve them. This information can also be submitted via our web site at
www.vitalinq.com. Additionally, an electronic version of this manual can be obtained at our web site.
Thank you for your help.
© Vis-A-Vis 2004-2013
Rev 04/11/2013
1
VITALINQ™ INTRODUCTION
Vitalinq is a communication system designed to
meet the specific needs that arise during diagnostic
and interventional procedures. Vitalinq enables
TM
physicians to have continuous two-way conversation
with control room operators throughout diagnostic
and catheterization procedures. Capable of picking up
by VIS-A-VIS, INC.
conversation in a normal tone of voice, Vitalinq allows
control room operators to respond immediately to
physicians requests. As vital signs are monitored by the control room operator, the physician can
receive up-to-the-moment communication on the patient’s condition.
The Vitalinq communication system provides speakers and microphones for the procedure room
(LAB) and control room (TEK). The speakers are mounted in the ceiling. Control room operators
have the option of using the overhead speaker and desk microphone, or a headset. The procedure
room microphone is attached to the video monitor (or monitor cluster) opposite the physician,
or optionally, integrated into the ceiling by replacing a standard ceiling tile. The unique
construction of our procedure room microphones contribute to Vitalinq’s high intelligibility, even
within the acoustically active space of a full-functioning lab. Designed to minimize the loss of
articulation by reducing the potential echo path, Vitalinq gathers and transmits speech in a highly
efficient manner.
Complete and comprehensive, the Vitalinq removes the need for talk-listen switching, eliminating
the risks posed by breaks in conversation. Physicians and control room operators may converse
without interruption.
Integrated into the console but operationally separate from the communication system is a stereo
system capable of playing music from a variety of sources. Sources include AM/FM radio
(subject to the limitations imposed by building shielding effects), compact discs and music from
external devices such as a smart phone, satellite radio, flash drive or any device capable of output
to a mini-stereo or USB jack.
We strive to provide the most flexible system available. To learn more about Vitalinq’s advanced
capabilities, please contact us at 1-800-319-6014 or by email at info@vitalinq.com.
Advanced capabilities and options include:
• Wireless headset to replace corded headset
• Auxiliary wireless headsets are available for scrub or circulator nurses to provide discreet
communication with the control room operator.
• Remote connections for headsets & foot switches.
• Support for multiple headsets / desk microphones.
• Telephone interconnectability.
Contact us for details.
1
1.1
System layout
2
2
SETTING UP THE VITALINQ™ SYSTEM
2.1
Description of the VITALINQ™ system
The Vitalinq is very easy to use and versatile. The standard system is composed of a pair of music
speakers and a communication speaker in both the procedure and control rooms. The speakers are
mounted overhead in the ceiling. The procedure room also has a microphone, either mounted to
the monitor array opposite the physician or, optionally, overhead in the ceiling. The control room
is where the console is located to which all devices are ultimately connected. Also in the control
room and plugged into the console, are a desk microphone and a headset with foot switch. One desk
microphone, headset and foot switch are included with each system.
On the front of the console, divided between the top and bottom, are controls for the music system
and controls for talking and listening to the procedure room, respectively. At the rear of the console
are 1/4” jacks for foot switches and a thumbnail adjustable control for the headset talk volume.
Words in BLUE throughout this document refer to labels on the console.
The LISTEN control, FOOT SWITCH jack and HEADSET jack on each side of the console work
together. If a headset is plugged into the HEADSET jack on the left side of the console, the foot
switch for this headset needs to be plugged into the LEFT FOOT SWITCH jack on the rear of
the console. Conversely, if a headset is plugged into the HEADSET jack on the right side of the
console, the foot switch for this headset needs to be plugged into the RIGHT FOOT SWITCH jack
on the rear of the console. When depressed, the foot switch allows the headset to transmit speech to
the procedure room. Without a foot switch connected, the headset constantly transmits sound to the
procedure room.
The volume of the headset earpiece is adjusted using the LISTEN volume control located adjacent to
the HEADSET jack. The volume for the procedure room communication speaker (used to transmit
speech from the control room) is controlled by the HEADSET TALK VOLUME switch located on
the rear of the console.
The OVERHEAD CONTROLS, at the bottom center of the console, are for the desk microphone and
speaker in the control room. In the OVERHEAD CONTROLS section are a TALK switch and an
overhead LISTEN VOLUME control. The BUTTON and TALK VOLUME are only used for setup.
The TALK/MUTE switch on the console should always be in the TALK position when using a desk
mic, and the LED will be RED. The TALK/MUTE switch and its associated LED are used primarily
with a Control room pyramid microphone (optional equipment), which has no other switch. In this
situation, when the LED is RED the people in the procedure room can hear you. With the TALK/
MUTE in MUTE, the LED will be GREEN and the Control room mic is off.
2.2
Initial settings
Turn LISTEN controls to the 12:00 position. LISTEN VOLUME control OFF. Plug power cord into
120 volt AC outlet. Set the TALK/MUTE switch to TALK. The LED above talk switch should be RED.
3
2.3
Adjusting the headset
Put on headset and listen to person in procedure room. LISTEN controls what you hear. HEADSET
TALK, on rear of console controls volume that procedure room hears. The headset microphone tube
telescopes. Move microphone tube tip close to the corner of your mouth. Pressing foot switch allows
you to talk and listen simultaneously to procedure room.
2.4
Adjusting the overhead controls
Unplug the headset. The OVERHEAD controls are at the lower front of the console between the
HEADSET jacks. Turn the LISTEN VOLUME switch to 3 and listen to the Lab. You should be able
to hear background noise. Lock the desk mic in the talk position by depressing the LOCK button
on the microphone base. The blue lamp behind the LOCK button will illuminate. Turn the TALK
VOLUME control clockwise while pressing the BUTTON until you just barely hear feedback squeal.
Release the BUTTON. The TALK volume level is now set. As you switch the LISTEN VOLUME
louder or softer, the sound in the Lab varies by an inverse amount to prevent feedback. When
finished, be sure to unlock the microphone by pressing the LOCK button again. The blue lamp will
go out.
3
VITALINQ™ OPERATING INSTRUCTIONS
OVERHEAD CONTROLS
LISTEN
LISTEN VOLUME
HEADSET
TALK VOLUME
BUTTON
1
OFF
2
3
HEADSET
4
LISTEN
TALK
5
MUTE
94A-07
3.1
ADJUSTING FOR MAXIMUM VOLUME SET LISTEN VOLUME TO 3,
PLACE MUTE SWITCH ON TALK, HOLD BUTTON IN, ADJUST TALK
VOLUME UNTIL FEEDBACK JUST STOPS, THEN RELEASE BUTTON.
FOR SERVICE CALL
1-800-319-6014
Initial operation of the headset
BLUE words are labels on console. Place the TALK switch on MUTE and the LISTEN VOLUME
control at OFF. Turn the headset LISTEN control to the middle of its rotation. The headset is easy to
adjust. The headband slides in and out of the ear-cup. Put the headset on. The headset microphone tube
telescopes. Move it so that the microphone tube tip is near the corner of your mouth. Listen to someone
in the procedure room.
Pressing the foot switch allows you to talk via the headset, to people in the procedure room. You will
hear the people in the procedure room whether the foot switch is pressed or not. Not pressing the
footswitch will mute your voice. Unplugging the foot switch un-mutes the headset microphone. Adjust
the headset LISTEN volume for a comfortable level by means of the volume control labeled LISTEN.
The left headset LISTEN volume control is for a headset plugged into the left jack and the right one
controls the right jack. The foot switches control the same side jack. The white slotted shaft on the rear
by the left footswitch jack labelled HEADSET TALK controls both of the headsets talk volume.
4
3.2
Initial Operation of the overhead speaker and desk microphone
Adjust the LISTEN VOLUME control to a comfortable level for people in the control room. To talk
to the procedure room without using the headset, place the TALK switch in the TALK position.
The GREEN light will turn RED. The desk mic has a push to talk switch on its base. If desired, the
microphone may be locked in the always on mode by pressing the LOCK button on the microphone
base. There is a blue light behind the button that lights up to show that it is locked on. To release the
always on mode, press the LOCK button again. There is a blue light behind the button that lights up
to show that it is locked on.
If the TALK VOLUME control is turned too far clockwise, you will hear a hum or squeal; turn it
down using your thumbnail or small screwdriver, as described in Section 2.5. It is normal to have to
speak louder when using the overhead TALK position. When not in use leave the TALK switch in
MUTE. The talk volume may be adjusted by following the directions on the console.
To lock the microphone in the “always
on” position, press the “Lock” button.
To unlock, press the “Lock” button
again. A blue light behind the button
is illuminated when the microphone is
locked on.
The “Talk” button is used for normal Push-To-Talk operation.
5
4
MUSIC SYSTEM OPERATION
4.1
Getting started
4.1.1 Music system power
button
1
Press to turn on the power/change the source (Radio/CD/USB/AUX).
2
Press for 1 second to turn off the power.
3
Press for more than 2 seconds to turn off the power and display.
4.2
Adjusting setup items
4.2.1
Canceling the DEMO mode
You can cancel the demonstration display which appears when the stereo is off.
1
Press and hold the select button.
The setup display appears.
2
Rotate the control dial until “DEMO” appears, then press it.
3
Rotate the control dial to select “DEMO-OFF,” then press it.
The setting is complete.
4Press O (BACK).
The display returns to normal reception/play mode.
4.2.2
Setting the clock
The clock uses a 12-hour digital indication.
1
Press and hold the select button.
The setup display appears.
2
Rotate the control dial until “CLOCKADJ” appears, then press it.
The hour indication flashes.
3
Rotate the control dial to set the hour and minute.
To move the digital indication, press
–/+.
4
After setting the minute, press the select button.
The setup is complete and the clock starts.
To display the clock, press
4.2.3
.
Additional setup items
1
Press and hold the select button.
The setup display appears.
2
Rotate the control dial until the desired item appears, then press it.
3
Rotate the control dial to select the setting, then press it.*
The setting is complete.
4Press O (BACK).
* For CLOCK-ADJ and BTM settings, step 4 is not necessary.
6
The following items can be set depending on the source and setting:
CLOCK-ADJ (Clock Adjust)
CT (Clock Time)
Activates the CT function: “ON,” “OFF”
BEEP
Activates the beep sound: “ON,” “OFF.”
CAUT ALM - NOT USED
AUX-A*1 (AUX Audio)
Activates the AUX source display: “ON,” “OFF”.
AUTO OFF
Shuts off automatically after a desired time when
the unit is turned off:
•• “NO”, “30S (Seconds)”
•• “30M (Minutes)”
•• “60M (Minutes).”
AUTO SCR (Auto Scroll)
Scrolls long items automatically: “ON,” “OFF.”
ZAP TIME (Zappin Time)
Selects the playback time for the ZAPPIN function.
•• “Z.TIME-1 (about 6 seconds),”
•• “Z.TIME-2 (about 15 seconds),”
•• “Z.TIME-3 (about 30 seconds).”
ZAP BEEP (Zappin Beep)
Has the beep sound between track passages:
“ON,” “OFF.”
LPF FREQ*2 - NOT USED
REAR/SUB- NOT USED
LPF SLOP*2 - NOT USED
DEMO (Demonstration)
Activates the demonstration: “ON,” “OFF.”
SW PHASE*3 - NOT USED
HPF FREQ (High Pass Filter Frequency)
Selects the front/rear speaker cut-off frequency:
“OFF,” “50Hz,”“60Hz,” “80Hz,” “100Hz,” “120Hz.”
DIMMER
Changes the display brightness.
•• “AT”: to dim the display automatically when you
turn lights on. (Available only when the illumination
control lead is connected.)
•• “ON”: to dim the display.
•• “OFF”: deactivate the dimmer.
COLOR (Preset Color)
Selects the preset color of the display and buttons
on the main unit.
CUSTOM-C (Custom Color)
Selects a preset color as a basis for further
customizing.
SND SYNC
Selects the color with sound synchronization:
“ON,” “OFF.”
WHT MENU
Sets the effect when the source is switched: “ON,” “OFF.”
START-WHT
Sets the start up color: “ON,” “OFF.”
7
M.DISPLAY (Motion Display)
“SA”: to show moving patterns and spectrum analyzer.
“OFF”: to deactivate the Motion Display.
HPF SLOP (High Pass Filter Slope)
Selects the HPF slope (effective only when HPF
FREQ is set to other than “OFF”): “1,” “2,” “3.”
LOUDNESS (Dynamic Loudness)
Reinforces bass and treble for clear sound at low
volume levels: “ON,” “OFF.”
ALO (Automatic Level Optimizer)
Adjust the playback volume level of all playback
sources to the optimum level: “ON,” “OFF.”
PARENTAL*4
Sets the parental lock to “ON” or “OFF,” and
edits the passcode.
BTM
*1 When the unit is turned off.
*2 When the audio output is set to “SUB-OUT” or
Rear Bass Enhancer is set to other than “OFF.”
*3 When the audio output is set to “SUB-OUT.”
*4 When the SiriusXM tuner is connected.
4.3
Location of controls and basic operations
This section contains instructions on the location of controls and basic operations.
1
SOURCE/OFF button
Press to turn on the power/change the source (Radio/CD/USB/Pandora USB/AUX).
Press and hold for 1 second to turn off the power.
Press and hold for more than 2 seconds to turn off the power and the display disappears.
2
SEEK +/– buttons
Radio:
To tune in stations automatically (press); find a station manually (press and hold).
CD/USB:
To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and
hold); reverse/fast-forward a track (press and hold).
Pandora USB:
To skip tracks (press
+).
3
ZAP button
To enter ZAPPIN™ mode.
4
Control dial/select button
To adjust volume (rotate); select setup items (press and rotate).
5
Disc slot
Insert the disc (label side up), playback starts.
6
Display window
7
(eject) button
To eject the disc.
8
USB Connector
To connect a USB device.
9
O (BACK) / MODE button
Press to return to the previous display/ select the radio band (FM/AM).
Press and hold to enter/cancel the passenger control/enter the bookmark mode (Pandora USB).
8
10
Front panel release button - LOCKED
11
(BROWSE) button
To enter the Quick-BrowZer™ mode; list the station (Pandora USB).
12
PTY/CAT button
To select PTY in RDS.
13
Number buttons
Radio:
To receive stored stations (press); store stations (press and hold).
CD/USB:
/
: ALBUM ▼/▲(during MP3/WMA/AAC playback)
To skip albums (press); skip albums continuously (press and hold).
: REP*3 page 15
: SHUF page 15
: PAUSE
To pause playback. To cancel, press again.
Pandora USB:
/
: Thumbs down (▼)/up (▲) (press and hold for 1 second)
14
DISP (display) / SCRL (scroll) button
To change display items (press); scroll the display item (press and hold).
15
AUX input jack
To connect a portable audio device.
4.4Radio
4.4.1
Storing and receiving stations
Storing automatically — BTM
1Press
repeatedly until “TUNER” appears.
repeatedly. You can select from FM1, FM2, FM3, AM1 or
To change the band, press
AM2.
2
Press and hold the select button.
The setup display appears.
3
Rotate the control dial until “BTM” appears, then press it.
The unit stores stations in order of frequency on the number buttons.
Storing manually
1
While receiving the station that you want to store, press and hold a number button (
to
) until “MEM” appears.
Receiving the stored stations
1
9
Select the band, then press a number button (
to
).
Tuning automatically
1
Select the band, then press
+/– to search for the station.
Scanning stops when the unit receives a station. Repeat this procedure until the desired station
is received.
Tip
+/– to locate the approximate
If you know the frequency of the station you want to listen to, press and hold
frequency, then press
+/– repeatedly to fine adjust to the desired frequency (manual tuning).
4.4.2RDS
FM stations with Radio Data System (RDS) service send inaudible digital information along with
the regular radio program signal.
Notes
Depending on the country/region, not all RDS functions may be available.
RDS will not work if the signal strength is too weak, or if the station you are tuned to is not
transmitting RDS data.
Changing display items
.
Press
Selecting PTY (Program Types)
Displays the currently received program type. Also searches your selected program type.
1Press
during FM reception.
The current program type name appears if the station is transmitting PTY data.
2
Rotate the control dial until the desired program type appears, then press it.
The unit starts to search for a station broadcasting the selected program type.
Type of programs:
NEWS (News), INFORM (Information), SPORTS (Sports), TALK (Talk), ROCK (Rock), CLS
ROCK (Classic Rock), ADLT HIT (Adult Hits), SOFT RCK (Soft Rock), TOP 40 (Top 40),
COUNTRY (Country), OLDIES (Oldies), SOFT (Soft), NOSTALGA (Nostalgia), JAZZ (Jazz),
CLASSICL (Classical), R AND B (Rhythm and Blues), SOFT R B (Soft Rhythm and Blues),
LANGUAGE (Foreign Language), REL MUSC (Religious Music), REL TALK (Religious Talk),
PERSNLTY (Personality), PUBLIC (Public), COLLEGE (College), WEATHER (Weather)
Note
You may receive a different radio program from the one you select.
Setting CT (Clock Time)
The CT data from the RDS transmission sets the clock.
1
Set “CT-ON” in setup.
Note
The CT function may not work properly even though an RDS station is being received.
10
4.5CD
4.5.1
Playing a disc
This unit can play CD-DA (also containing CD TEXT) and CD-R/CD-RW (MP3/WMA/AAC files).
1
Insert the disc (label side up).
Playback starts automatically.
To eject the disc, press
.
Note
When ejecting/inserting a disc, keep any USB devices disconnected to avoid damage to the disc.
Changing display items
Displayed items may differ depending on the disc type, recording format and settings.
Press
4.6
.
USB devices
• MSC (Mass Storage Class)-type USB devices compliant with the USB standard can be used.
• Corresponding codec is MP3 (.mp3), WMA (.wma), AAC (.m4a) and AAC (.mp4).
• Backup of data in a USB device is recommended.
4.6.1
Playing back a USB device
1
Open the USB cover, then connect the USB device to the USB connector with its USB
cable.
Playback starts.
If a USB device is already connected, to start playback, press
“USB” appears.
To stop playback, press and hold
repeatedly until
for 1 second.
To remove the USB device, stop the USB playback, then remove the USB device.
Notes
Do not use USB devices so large or heavy that they may fall down due to vibration, or cause a loose
connection.
Do not detach the front panel during playback of the USB device, otherwise USB data may be damaged.
Changing display items
Displayed items may differ depending on the USB device, recording format and settings.
11
Press
.
Notes
The maximum number of displayable data is as follows.
• folders (albums): 128
• files (tracks) per folder: 500
It may take time for playback to begin, depending on the amount of recorded data.
DRM (Digital Rights Management) files may not be played.
During playback or fast-forward/reverse of a VBR (Variable Bit Rate) MP3/WMA/AAC file, elapsed playing
time may not display accurately.
Playback of the following MP3/WMA/AAC files is not supported.
• lossless compression
• copyright-protected
4.7iPod
In these Operating Instructions, “iPod” is used as a general reference for the iPod functions on the
iPod and iPhone, unless otherwise specified by the text or illustrations.
4.7.1
Playing back iPod
Before connecting the iPod, turn down the volume of the unit.
1
Open the USB cover, then connect the iPod to the USB connector with the USB connection
cable for iPod (not supplied)*.
The tracks on the iPod start playing automatically from the point last played.
If an iPod is already connected, to start playback press
appears. (“IPD” appears in the display when iPod is recognized.)
Press and hold
repeatedly until “USB”
for 1 second to stop playback.
To remove the iPod, stop the iPod playback, then remove the iPod.
Caution for iPhone
When you connect an iPhone via USB, telephone volume is controlled by iPhone itself. In order to
avoid sudden loud sound after a call, do not increase the volume on the unit during a telephone call.
Tip
iPod is recharged while the unit is turned on.
12
Resuming mode
When the iPod is connected to the dock connector, playback starts in the mode set by the iPod. In
this mode, the following buttons do not function.
•
(REP)
•
(SHUF)
Changing display items
Press
.
Note
Some letters stored in iPod may not be displayed correctly.
Skipping albums, podcasts, genres, playlists and artists
To
Skip
Skip continuously
4.7.2
Do this
/
(ALBUM ▼/▲) [press once for each]
Press
/
(ALBUM ▼/▲) [hold to desired point]
Press and hold
Operating an iPod directly — Passenger control
You can operate an iPod directly even when connected to the dock connecter.
1
During playback, press and hold
.
“MODE IPOD” appears and you will be able to operate the iPod directly.
To exit the passenger control, press and hold
and the play mode will change to iPod mode.
. Then “MODE AUDIO” will appear
Note
The volume can be adjusted only by the unit.
4.8
Pandora® via USB (iPhone)
Pandora Radio is available to stream music through your iPhone. You can control Pandora on a
USB-connected iPhone from this unit.
Download the latest version of Pandora and obtain more information from www.pandora.com
Notes
Certain Pandora service functions may not be available.
Pandora’s service is currently only available in the U.S.
4.8.1
Playing back Pandora via the USB (external) connector
Before connecting the iPhone, turn down the volume of the unit.
1
13
Open the USB cover, then connect the iPhone to the USB connector with the USB
connection cable for iPhone (not supplied)*
2Press
repeatedly until “PANDORA USB” appears.
3
Launch Pandora on the iPhone.
4
Adjust the volume on this unit.
To pause playback
. To cancel, press again.
Press
To skip a song
+.
Press
Notes
You cannot skip back to the previous song.
Pandora limits the number of skips allowed.
“Thumbs” feedback
The “Thumbs Up” or “Thumbs Down” feedback allows you to personalize stations to suit your
preference.
Thumbs Up
During playback, press and hold
(▲) for 1 second.
Thumbs Down
During playback, press and hold
(▼) for 1 second.
Station list
The station list allows you to easily select a desired station.
1
During playback, press (BROWSE).
2Press
3
+ to select the sorting order “DATE” or “A-Z.”
Rotate the control dial to select the desired station, then press it.
Playback starts.
QuickMix
QuickMix allows you to listen to songs played on one or more Pandora stations in your station list randomly.
Edit your QuickMix station selections on the device before connection.
Bookmarking
The song or artist currently being played can be bookmarked and stored in your Pandora account.
1
During playback, press and hold
until “BOOKMARK” appears.
2
Rotate the control dial to select “TRK” (Track) or “ART” (Artist), then press it.
14
4.9
Searching and playing tracks
4.9.1
Playing tracks in various modes
You can listen to tracks repeatedly (repeat play) or in random order (shuffle play). Available play
modes differ depending on the selected sound source.
1
During playback, press
(REP) or
(SHUF) repeatedly until the desired play
mode appears.
Playback in selected play mode may take time to start.
Repeat play
Select
TRACK
N ALBUM
N PODCAST*1
N ARTIST*1
N PLAYLIST*1
N GENRE*1
N OFF
To play
track repeatedly.
album repeatedly.
podcast repeatedly.
artist repeatedly.
playlist repeatedly.
genre repeatedly.
track in normal order (Normal play).
Shuffle play
Select
SHUF ALBUM
SHUF DISC*2
SHUF PODCAST*1
SHUF ARTIST
SHUF PLAYLIST
SHUF GENRE*1
SHUF DEVICE*3
SHUF OFF
To play
album in random order.
disc in random order.
podcast in random order.
artist in random order.
playlist in random order.
genre in random order.
track in normal order.
track in normal order (Normal play).
*1 iPod only
*2 CD only
*3 USB and iPod only
15
4.9.2
Searching a track by name — Quick-BrowZer™
You can search for a track in a CD or USB device easily by category.
1Press
(BROWSE)*.
The unit enters the Quick-BrowZer mode, and the list of search categories appears.
When the track list appears, press O (BACK) repeatedly until the desired search category appears.
(BROWSE) for more than 2 seconds to directly return to the
* During playback, press
beginning of the category list (USB only).
2
Rotate the control dial to select the desired search category, then press it to confirm.
3
Repeat step 2 until the desired track is selected.
Playback starts.
To exit the Quick-BrowZer mode, press
(BROWSE).
Searching by skip items — Jump mode
When many items are in a category, you can search the desired item quickly.
1Press
+ in Quick-BrowZer mode.
The item name will appear.
2
Rotate the control dial to select the item near the one desired.
It skips in steps of 10% of the total item number.
3
Press the select button.
The display returns to the Quick-BrowZer mode and the selected item appears.
4
Rotate the control dial to select thedesired item and press it.
Playback starts if the selected item is a track.
To cancel Jump mode, press O (BACK) or
–.
Searching by alphabetical order — Alphabet search
When an iPod is connected to the unit, you can search for a desired item alphabetically.
1Press
+ in Quick-BrowZer mode.
2
Rotate the control dial to select the first letter of the desired item, then press it.
A list of items beginning with the selected letter appears in alphabetical order.
3
Rotate the control dial to select the desired item, then press it.
Playback starts if the selected item is a track.
To cancel Alphabet search, press O (BACK) or
–.
Notes
In Alphabet search, a symbol or article (a/an/the) before the selected letter of the item is excluded.
Depending on the search item you select, only Jump mode may be available.
Alphabet search may take some time, depending on the amount of tracks.
16
4.9.3
Searching a track by listening to track passages — ZAPPIN™
While playing back short track passages in a CD or USB device in sequence, you can search for a track
you want to listen to. ZAPPIN mode is suitable for searching for a track in shuffle or shuffle repeat mode.
1Press
during playback.
Playback starts from a passage of the next track. You can select the playback time.
2
Press the select button or
when a track you want to listen is played back.
The track that you select returns to normal play mode from the beginning.
Pressing O (BACK) also confirms a track to playback.
Tips
Press
Press
4.10
/
+/– in ZAPPIN mode to skip a track.
(ALBUM ▼/▲) in ZAPPIN mode to skip album.
Changing the illumination
4.10.1 Changing the color of display and buttons — Dynamic Color Illuminator
Dynamic Color Illuminator allows you to change the color of the display and buttons on the main unit to
match the car’s interior. You can select from 12 preset colors, customized color and 5 preset patterns.
Preset colors:
RED, AMBER, M_AMBER, YELLOW, WHITE, LIGHT GREEN, GREEN, LIGHT BLUE, SKY
BLUE, BLUE, PURPLE, PINK.
Preset patterns:
RAINBOW, OCEAN, SUNSET, FOREST, RANDOM.
1
Press and hold the select button.
The setup display appears.
2
Rotate the control dial until “COLOR” appears, then press it.
3
Rotate the control dial to select the desired preset color, then press it.
4Press O (BACK).
Note
If the control dial is rotated rapidly, the color of the display and the buttons may change too quickly.
Customizing the display and button color — Custom Color
You can register a customized color for the display and buttons.
1
17
Press and hold the select button.
The setup display appears.
2
Rotate the control dial until “CUSTOM-C” appears, then press it.
3
Rotate the control dial until “BASE” appears, then press it.
You can select a preset color as a basis for further customizing.
When you select “BASE,” customized color is overwritten.
4
Rotate the control dial to select from “RGB RED,” “RGB GRN,” or “RGB BLUE,”
then press it.
5
Rotate the control dial to adjust the color range, then press it.
Adjustable color range: “0” – “32.”
You cannot set “0” for all color ranges.
6Press O (BACK).
4.10.2 Advanced color setting
Changing the color with sound synchronization — Sound Synchronization
When you select a preset pattern, sound synchronization becomes effective.
1
Press and hold the select button.
The setup display appears.
2
Rotate the control dial until “SND SYNC” appears, then press it.
3
Rotate the control dial to select “SYNC-ON,” then press it.
4Press O (BACK).
Displaying clear color — White Menu
You can display the menu more clearly (White) without concern for color setting.
1
Press and hold the select button.
The setup display appears.
2
Rotate the control dial until “WHT MENU” appears, then press it.
3
Rotate the control dial to select “WHITE-ON,” then press it.
4Press O (BACK).
To cancel White Menu, select “OFF” on step 3.
Start up effect — Start White
When you push
on, the color of display and the buttons on the main unit turns
white once, and then the color changes to the customized color.
1
Press and hold the select button.
The setup display appears.
2
Rotate the control dial until “STARTWHT” appears, then press it.
3
Rotate the control dial to select “WHITE-ON,” then press it.
4
Press (BACK).
To cancel Start White, select “OFF” on step 3.
18
4.11
Sound Settings and Setup Menu
4.11.1 Changing the sound settings
Adjusting the sound characteristics
1
During reception/playback, press the select button.
2
Rotate the control dial until the desired menu item appears, then press it.
3
Rotate the control dial to select the setting, then press it.
4Press O (BACK).
The following items can be set:
EQ7 PRESET
EQ7 SETTING
POSITION - NOT USED
BALANCE
Adjusts the sound balance: “RIGHT-15” – “CENTER” – “LEFT-15.”
FADER
Adjusts the relative level between rooms: “FRONT-15” – “CENTER” – “REAR-15.”
DM+
RB ENH (Rear Bass Enhancer) - NOT USED
SW LEVEL (Subwoofer Level) - NOT USED
AUX VOL*1 (AUX Volume level)
Adjusts the volume level for each connected auxiliary equipment: “+18 dB” – “0 dB” – “–8 dB.”
This setting negates the need to adjust the volume level between sources.
*1 When AUX source is activated
Selecting the sound quality — EQ7 Preset
You can select an equalizer curve from 7 equalizer curves (XPLOD, VOCAL, EDGE, CRUISE,
SPACE, GRAVITY, CUSTOM or OFF).
1
During reception/playback, press the select button.
2
Rotate the control dial until “EQ7 PRESET” appears, then press it.
3
Rotate the control dial until the desired equalizer curve appears, then press it.
4Press O (BACK).
To cancel the equalizer curve, select “OFF” in step 3.
Tip
The equalizer curve setting can be memorized for each source.
19
4.11.2 Customizing the equalizer curve — EQ7 Setting
“CUSTOM” of EQ7 allows you to make your own equalizer settings.
1
Select a source, then press the select button.
2
Rotate the control dial until “EQ7 SETTING” appears, then press it.
3
Rotate the control dial until “BASE” appears, then press it.
You can select an equalizer curve as a basis for further customizing.
4
Rotate the control dial to select the equalizer curve, then press it.
5
Setting the equalizer curve.
1. Rotate the control dial to select the frequency range, then press it.
BAND1: 63 Hz
BAND2: 160 Hz
BAND3: 400 Hz
BAND4: 1 kHz
BAND5: 2.5 kHz
BAND6: 6.3 kHz
BAND7: 16.0 kHz
2. Rotate the control dial to adjust the volume level, then press it.
The volume level is adjustable in 1 dB steps, from -6 dB to +6 dB.
Repeat steps 1 and 2 to adjust other frequency ranges.
6Press O (BACK) twice.
The equalizer curve is stored in “CUSTOM.”
DM+ Advanced
DM+ Advanced improves digitally compressed sound by restoring high frequencies lost in the
compression process.
1
During playback, press the select button.
2
Rotate the control dial until “DM+” appears, then press it.
3
Rotate the control dial to select “ON,” then press it.
4Press O (BACK).
Tip
The DM+ setting can be memorized for each source.
20
4.12 Auxiliary audio equipment
By connecting an optional portable audio device to the AUX input jack (stereo mini jack) on the unit
and then simply selecting the source, you can listen on your car speakers.
4.12.1 Connecting the portable audio device
1
Turn off the portable audio device.
2
Turn down the volume on the unit.
3
Connect the portable audio device to the unit with a connecting cord (not supplied)*.
* Be sure to use a straight type plug.
Adjusting the volume level
Be sure to adjust the volume for each connected audio device before playback.
1
Turn down the volume on the unit.
2Press
repeatedly until “AUX” appears.
3
Start playback of the portable audio device at a moderate volume.
4
Set your usual listening volume on the unit.
5
Adjust the input level.
4.12.2 SiriusXM tuner
By connecting an optional SiriusXM tuner, you can use the features and functions of the SiriusXM
satellite radio (Sirius and XM subscriptions sold separately). For more details on the services, visit
the following web site: http://www.siriusxm.com/
Selecting channels
21
1
During playback, press
(BROWSE) to enter the browse mode.
2
Rotate the control dial to select the desired channel, then press it.
Selecting categories
1
During playback, press
to enter browse mode.
2
Rotate the control dial to select the desired category, then press it.
Parental control
The channels containing unsuitable contents for children are preset to block. To unblock the channel,
enter the passcode.
1
On the set up menu, rotate the control dial to select “PARENTAL,” then press it.
2
Rotate the control dial to select “LOCK SEL,” then press it.
3
Rotate the control dial to select “OFF,” then press it.
4
On the passcode input display, enter the four-digit passcode, then press the control dial.
The initial passcode is “0000.”
To change the passcode
1
On the set up menu, rotate the control dial to select “PARENTAL,” then press it.
2
Rotate the control dial to select “CODE EDIT,” then press it.
3
On the current passcode input display, enter the current passcode, then press the control
dial.
The initial passcode is “0000.”
4
On the new passcode input display, enter new 4-digit passcode, then press the control dial.
Displaying the SiriusXM Radio ID
1
During playback, press (BROWSE) to enter the browse mode.
2
Rotate the control dial to select the channel “0,” then press it.
Changing display items
Press
.
22
4.13 Additional Information
4.13.1 Notes on discs
• Do not expose discs to direct sunlight or heat sources such as hot air ducts, nor leave it in a car
parked in direct sunlight.
• Before playing, wipe the discs with a cleaning cloth from the center out. Do not use solvents such
as benzine, thinner, commercially available cleaners.
• This unit is designed to play back discs that conform to the Compact Disc (CD) standard.
DualDiscs and some of the music discs encoded with copyright protection technologies do not
conform to the Compact Disc (CD) standard, therefore, these discs may not be playable by this unit.
Discs that this unit CANNOT play
• Discs with labels, stickers, or sticky tape or paper attached.
Doing so may cause a malfunction, or may ruin the disc.
• Discs with non-standard shapes (e.g., heart, square, star).
Attempting to do so may damage the unit.
• 8 cm (3 1/4 in) discs.
Notes on CD-R/CD-RW discs
• The maximum number of: (CD-R/CD-RW only)
»» folders (albums): 150 (including root folder)
»» files (tracks) and folders: 300 (may less than 300 if folder/file names contain many characters)
»» displayable characters for a folder/file name: 32 (Joliet)/64 (Romeo)
• If the multi-session disc begins with a CDDA session, it is recognized as a CD-DA disc, and
other sessions are not played back.
• Discs that this unit CANNOT play
»» CD-R/CD-RW of poor recording quality.
»» CD-R/CD-RW recorded with an incompatible recording device.
»» CD-R/CD-RW which is finalized incorrectly.
»» CD-R/CD-RW other than those recorded in music CD format or MP3 format conforming to
ISO9660 Level 1/Level 2, Joliet/Romeo or multi-session.
4.13.2 Playback order of MP3/WMA/ AAC files
23
4.13.3 About iPod
You can connect to the following iPod models. Update your iPod devices to the latest software
before use.
Made for
• iPod touch (4th generation)
• iPod touch (3rd generation)
• iPod touch (2nd generation)
• iPod touch (1st generation)
• iPod classic
• iPod with video*
• iPod nano (6th generation)
• iPod nano (5th generation)
• iPod nano (4th generation)
• iPod nano (3rd generation)
• iPod nano (2nd generation)
• iPod nano (1st generation)*
• iPhone 4
• iPhone 3GS
• iPhone 3G
• iPhone
* Passenger control is not available for iPod nano (1st generation) or iPod with video.
“Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed
to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to
meet Apple performance standards. Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards. Please note that the use of this accessory with iPod
or iPhone may affect wireless performance.
4.13.4 Safety precautions
WARNING
To prevent injury or fire, take the following precautions:
• To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools)
inside the unit.
• If the unit starts to emit smoke or strange smells, turn off the power immediately and call us.
• Be careful not to drop the unit or subject it to strong shock. The unit may break or crack because
it contains glass parts.
• Do not touch the liquid crystal fluid if the LCD is damaged or broken due to shock. The liquid
crystal fluid may be dangerous to your heath or even fatal. If the liquid crystal fluid from the
LCD contacts your body or clothing, wash it off with soap immediately.
24
CAUTION
To prevent damage to the machine, note the following:
Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of water splashing.
Do Not Load 3-in. CDs in the CD slot
If you try to load a 3 in. CD with its adapter into the unit, the adapter might separate from the CD
and damage the unit.
Do Not Load CDs with attached labels
If you try to load a CD with an attached label, it may jam and damage the unit.
The following malfunctions may result from using such discs:
• Inability to eject a disc (due to a label or sticker peeling off and jamming the eject mechanism).
• Inability to read audio data correctly (e.g., playback skipping, or no playback) due to heat
shrinking of a sticker or label causing a disc to warp.
NOTE:
The illustrations of the display and the panel appearing in this manual are examples used to explain
more clearly how the controls are used. Therefore, what appears on the display in the illustrations
may differ from what appears on the display on the actual equipment, and some of the illustrations
on the display may represent something impossible in actual operation.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a dry soft cloth. If the faceplate is stained badly,
wipe the stain off with a cloth moistened with neutral cleaner, then wipe neutral detergent off.
Applying spray cleaner directly to the unit may affect its mechanical parts. Wiping the faceplate
with a hard cloth or using a volatile liquid such as thinner or alcohol may damage the surface or
erase characters.
Cleaning the CD Slot
As dust tends to accumulate in the CD slot, clean it every once in a
while. Your CDs can get scratched if you put them in a dusty CD slot.
25
5
TROUBLESHOOTING GUIDE
VITALINQ™ Communications Troubleshooting Guide
Call us first! We want to hear from you. 1-800-319-6014 or support@vitalinq.com
The communication system between the procedure room and control room is very easy to repair. All
devices unplug for easy replacement.
5.1
Most likely problems
Nothing works.
Check to see that the power cord is plugged in, and that the white (or grey), and blue cables are
plugged into the proper jacks.
No music.
Check to see that the white and blue cables are plugged all the way into the proper jacks. Try a CD.
FM or AM stations may be blocked by the shielding effect of the building. See section 4 for music
system operating instructions.
People in Procedure Room hear unwanted speech or noise from Control Room.
If the Console ‘TALK’ switch is up (LED is red) and the desk mic talk bar is depressed or locked on,
the people in the Procedure Room will hear the Control Room via the Control Room microphone.
This will also happen if a headset is connected and the Foot Switch is pressed or it is unplugged or
not plugged in all the way.
Operator can’t hear people in the Procedure Room while wearing Headset.
Verify that Headset LISTEN control is turned clockwise; Verify that Headset plug is in all the way.
Try another Headset. Try plugging the Headset into the other jack on the Console and adjust its
LISTEN control. Verify that the Foot Switch is plugged into the same side jack.
HEADSET AND FOOTSWITCH MUST BE CONNECTED TO OPPOSITE SIDE FROM
DESK MIC CONNECTION. IF HEADSET IS PLUGGED INTO SAME SIDE AS DESK MIC,
THE HEADSET MIC WILL BE MUTED.
Doctor can’t hear the Operator.
•
•
•
•
Verify that Headset plug is in all the way.
Try another Headset.
Unplug the Foot Switch. If the Doctor can hear, then replace Foot Switch.
Move Headset and Foot Switch to jacks on the other side of Console. (The left and right sides of
the Console are separate Headset channels.)
• On the rear of the Console are small white slotted shaft, which controls Headsets ‘TALK’volume.
The‘TALK’and ’LISTEN’ volume controls and Foot Switch control the Headset plugged into the
same side of the console.
• Place the ‘TALK-MUTE Switch’ in the up (“TALK”) position. Press the desk mic talk bar. (This
uses the desk microphone and not the Headset.) If the Doctor can now hear the Operator then the
problem is that the Headset or Headset circuit of the Console is not working. If the Doctor still
can’t hear, the problem is either in the White Cable, the Console or the Cath Lab microphone.
26
5.2
Music troubleshooting guide
The following checklist will help you remedy problems you may encounter with your unit.
General
No sound
• The volume is too low.
• The CD is incompatible with the disc format (MP3/WMA).
• The unit is turned off. Turn unit ON by Pressing (SOURCE).
No beep sound.
The beep sound is canceled (see 4.2.3).
The contents of the memory have been erased.
The power to the unit has been disconnected (unplugged).
During playback or reception, demonstration mode starts.
If no operation is performed for 5 minutes with “DEMO-ON” set, demonstration mode starts.
Set “DEMO-OFF” (see 4.2.1).
The display disappears from/does not appear in the display window.
The dimmer is set “DIM-ON” (see 4.2.3).
The display disappears if you press and hold ( SOURCE/OFF).
Press and hold ( SOURCE/OFF) on the unit until the display appears.
The Auto Off function does not operate.
The unit is turned on. The Auto Off function activates after turning off the unit.
Turn off the unit.
USB playback
You cannot play back items via a USB hub.
This unit cannot recognize USB devices via a USB hub.
Cannot play back items.
A USB device does not work.
Reconnect it.
The USB device takes longer to play back.
The USB device contains files with a complicated tree structure.
A beep sounds.
During playback, the USB device has been disconnected.
Before disconnecting a USB device, make sure to stop playback first for data protection.
The sound is intermittent.
The sound may be intermittent at a high-bit-rate of more than 320 kbps.
27
CD Playback
The disc cannot be loaded.
• Another disc is already loaded.
• The disc has been forcibly inserted upside down or in the wrong way.
The disc does not playback.
• Defective or dirty disc.
• The CD-Rs/CD-RWs are not for audio use (see 4.10).
MP3/WMA/AAC files cannot be played back.
The disc is incompatible with the MP3/WMA/AAC format and version (see 4.10).
MP3/WMAAAC files take longer to play back than others.
The following discs take a longer time to start playback.
• a disc recorded with a complicated tree structure.
• a disc recorded in Multi Session.
• a disc to which data can be added.
The display items do not scroll.
• For discs with very many characters, those may not scroll.
• “A.SCRL” is set to “OFF”. Set “A.SCRL-ON” (see 4.2.3).
Press and hold (DSPL)(SCRL).
The sound skips.
Defective or dirty disc.
The operation buttons do not function., The disc will not eject.
Unplug the unit momentarily.
Radio reception
The stations cannot be received. The sound is hampered by noises.
• Check the frequency.
• An external antenna may be necessary. Call us.
Preset tuning is not possible.
• Store the correct frequency in the memory.
• The broadcast signal is too weak.
Automatic tuning is not possible.
• Setting of the local seek mode is not correct.
»» Tuning stops too frequently: Set “LOCAL-ON” (see 4.2.3).
»» Tuning does not stop at a station: Set “LOCAL-OFF(see 4.2.3).
• The broadcast signal is too weak.
Perform manual tuning.
During FM reception, the “ST” indication flashes.
• Tune in the frequency accurately.
• The broadcast signal is too weak.
Set “MONO-ON” (see 4.2.3).
28
An FM program broadcast in stereo is heard in monaural.
The unit is in monaural reception mode.
Set “MONO-OFF’ (see 4.2.3).
RDS
PTY displays “- - - - - - - -.”
• The current station is not an RDS station.
• RDS data has not been received.
• The station does not specify the program type.
Error Displays/Messages
CHECKING
The unit is confirming the connection of a USB device.
Wait until confirming the connection is finished.
ERROR
• The disc is dirty or inserted upside down.
Clean or insert the disc correctly.
• A blank disc has been inserted.
• The disc cannot play due to a problem.
Insert another disc.
• USB device was not automatically recognized.
Reconnect it again.
• Press
to remove the disc.
FAILURE (Illuminates until any button is pressed.) - Call us.
HUB NO SUPRT (HUB Not Support)
USB hub is not supported on this unit.
NO DEV
(SOURCE/OFF) is selected without a USB device connected. A USB device or a USB cable has
been disconnected during playback.
Be sure to connect a USB device and USB cable.
NO MUSIC
The disc does not contain a music file.
Insert a music CD in this unit or MP3 playable changer.
NO NAME
A disc/track name is not written in the track.
RESET
The CD unit cannot be operated due to a problem.
Momentarily unplug the unit.
29
INSTALLATION
6
PLANNING THE VITALINQ™ INSTALLATION
There are microphones and speakers for the procedure room and for the control room. The control
room utilizes a desk microphone or a headset. The procedure room microphone is either a 24”
square, pyramid shaped microphone that replaces a ceiling tile or a monitor mounted microphone.
All cables are pre-terminated and may be run free or in conduit, subject to local regulations.
Using the layout in “7.1 Installing ceiling devices” and the instructions in 6.1 and 6.2, find locations
for the microphones and speakers. Remove the ceiling tiles at these locations and check for adequate
space above the ceiling. The tiles will be used in “7.1 Installing ceiling devices.” Relocate only if
necessary. Follow local regulations regarding securing these devices.
6.1
Procedure room (LAB)
In the procedure room, the pyramid microphone should be above the table in front of the physician.
Alternatively, a video monitor mounted microphone may be used if the pyramid isn’t feasible. For
the physician to hear best, the communication speaker should be near the physician and more than
six feet away from the microphone and the door to the control room. The music speakers should be
placed about four feet on either side of the physician, usually at the ends of the table. Follow local
regulations regarding securing these devices.
6.2
Control room (TEK)
In the control room, the operator’s desk microphone should be placed in a position convenient for the
operator. For the best operation, the communication speaker should be more than six feet away from
the microphone and the door to the procedure room. The music speakers should be placed in the ceiling,
three or four feet on either side of the operator. If provided, the optional auxiliary wireless headset
should be located near the console. Follow local regulations regarding securing these devices.
6.3
Control room console
The cables from the ceiling devices need to connect to the rear of the desk console. See layout in “7.1.
Installing ceiling devices.” If you are installing before the walls are sheet-rocked, use a junction
box near the console and one in the ceiling. Connect them with a 1” conduit. Cables can be pulled
through by staggering the connectors. Follow local regulations regarding securing these devices.
The communication system has volume controls for headset and overhead devices. Headset jacks are
on the front of the console and foot switch / desk microphone jacks are on the rear.
30
7
INSTALLING VITALINQ™ CEILING DEVICES
7.1
Installing ceiling devices
There are two modular, gray eight conductor jacks on the microphone pyramid, communication
speaker and music speakers. The Ethernet cables can be connected to the ceiling devices in any
convenient sequence. The devices mount in the ceiling. The peak of the pyramid goes up. The flange
rests on the ceiling tile grid.
If there isn’t room for a 24” x 24” pyramid or if you have a non-grid ceiling, a monitor mounted
microphone is available. See Sections 7.2 and 7.3.
1. Determine placement of all ceiling devices. In the procedure room, a microphone pyramid
should be located above the table in front of the physician. A communications speaker should be
located in the general area near the physician and more than six feet away from the microphone
and the door to the control room. A right music speaker should be located at the table end that
would be to the right of the physician, and a left music speaker at the table end that would be to
the left of the physician. In the control room, the communication speaker should be more than six
feet away from the microphone and the door to the procedure room. Music speakers should be
located left and right appropriate to the operator position.
2. Remove the ceiling tiles in the locations you have determined for the ceiling devices.
3. In the speaker box, the communication speakers are packed individually and are marked
COMM. The 2 pairs of music speakers are packed individually, two left and two right and are
marked MUSIC. A speaker support plate is provided for each speaker.
* Be careful when handling the support plate as the edges can be sharp!!
Take the ceiling tiles you removed in step 2 and draw a straight line on the backside from corner to
corner. Place the support plate over the lines you drew on the tile and line up the template with the
lines to center the template. The plate must not extend past the edges of the tile. Mark the circle and
cut it out with a knife or drywall saw. Remove the grille of the speaker by rotating the securing legs
on the back of the speaker and gently pushing them down towards the speaker grille. Replace the
legs after grille removal to their original position. Put the speaker in the hole from the front side of
the tile. Position the support plate over the speaker on the rear of the tile. Rotate out the legs on the
back and screw down the four phillips head screws on the front to pull the legs against the support
plate. Be careful not to over tighten the screws. If needed after installation, the grill may be
removed with a bent paperclip.
31
Speaker installation detail
Speaker
Support
Plate
Speaker
(Mounting Dogs
Extended)
Tile shown cut
away for clarity
Follow local regulations regarding securing these ceiling devices. If none apply, add a safety wire
(ceiling hanger wire) from the grid support to the device.
4. Install all devices into selected locations.
All speakers and the pyramids have dual GRAY jacks, and there is no particular sequence for
interconnection. This allows for much flexibility in cable routing. Connect all of the devices in
the procedure room (LAB), including COMM speaker, pyramid (if provided) and the two MUSIC
speakers (left and right) with short white cables. The procedure room device nearest the console is
connected to the console with a long white cable. Spare cables and connectors are provided. In the
control room, connect COMM and the two MUSIC speakers (left and right) with short blue cables.
Connect the control room device nearest the console to it, with a blue cable.
NOTE: Older devices having BLACK jacks cannot be used with this system.
32
7.2
Monitor mounted microphone - MM5 - connection options
If a monitor mounted microphone is supplied, there are different options for connections.
See below:
SEE NOTE 3
CAT5 to
LAB speakers
SEE
NOTES
BNC to BNC
coupler
(supplied)
BNC & CAT5
extension
cables not
provided
MM-5 Monitor
microphone
BNC Connection to
MM-5 Jack using
BNC to RCA adapter
VITALINQ
CONSOLE
33
BNC/RCA coax
to CAT5 cable
adaptor
NOTES:
There are 3 options for connection
of Monitor Mic to Console, depending
on availability of cable & ease of
accessibility.
1. Monitor Mic can be run directly
to Console AUX RCA jack using an
existing available video cable with the
supplied BNC to RCA adapter.
2. Monitor Mic cabling can be run into
ceiling space or equipment room and
connected to a BNC to CAT5 adapter
box with a BNC to RCA adapter. A
separate CAT5 cable is run to
the console. Both the White CAT5 cable
and the MM-5 cable connect to the LAB
jack using the enclosed splitter.
3. Alternatively, the adapter box can be
inserted into the ceiling device loop in
the Lab using the enclosed splitter
inserted into the Connection box as
needed.
White CAT5 cable
to splitter in
console LAB jack
Vis-A-Vis, Inc.
7936 Camino Circle
Miami, FL 33143
vitalinq@bellsouth.net
305-274-3713
© Vis-A-Vis 2004-2008
MM-5 MONITOR MICROPHONE LAB CONNECTIONS
7.3
Monitor mounted microphone placement
Monitor Mic MM-5 shown mounted to Video monitor bezel with supplied Dual-Lock™.
Pick-up pattern is about 180º in the horizontal plane and about 20º in the vertical plane. Mic cable is
coax with a BNC plug. An adapter box is provided with a BNC jack and an Ethernet jack.
Cabling to the console may be either Ethernet or coax.
34
8
INSTALLING THE VITALINQ™ CONSOLE
8.1
Front of Console
Plug the headset into a headset jack on the front of the console closest to the operator’s normal
working location.
OVERHEAD CONTROLS
LISTEN
LISTEN VOLUME
HEADSET
TALK VOLUME
BUTTON
1
OFF
2
3
HEADSET
4
LISTEN
TALK
5
MUTE
94A-07
ADJUSTING FOR MAXIMUM VOLUME SET LISTEN VOLUME TO 3,
PLACE MUTE SWITCH ON TALK, HOLD BUTTON IN, ADJUST TALK
VOLUME UNTIL FEEDBACK JUST STOPS, THEN RELEASE BUTTON.
FOR SERVICE CALL
1-800-319- 6014
Note:
The Console is usually placed on control room counter near operator. If this is not possible,
it may be placed in another location, convenient for operation of music controls. An optional
remote connection for the headset and footswitch may located near the operator.
35
8.2
Rear of console
• Plug the Desk Mic into the jack marked FOOT SWITCH OR AUX IN on the opposite side from
the headset. For example, if you plug the headset into the right jack, plug the desk mic into
the left one.
• Plug the white Procedure room cable into the jack marked LAB WHITE.
• Plug the blue Control room cable into the jack marked TEK BLUE.
• Plug foot switch into foot switch jack on the SAME side that you plugged in the headset.
• The jacks marked MM5, BLACK, YELLOW, or SILVER are used for optional equipment.
• Instructions for using these jacks are included with the equipment.
• The ANT jack is provided for using an external antenna in weak reception areas.
When a monitor mounted microphone (MM5) is provided, there are many factors that influence
its connections, so there are many options. See Section 3.2 for all options. The monitor mounted
microphone can be directly connected to the MM5 jack with a BNC to RCA adapter.
• Plug the three conductor power cable into the POWER jack. Don’t plug it in to an AC power
outlet yet.
Proceed to Section 2: “Setting up the VITALINQ™ system”
NO USER SERVICEABLE PARTS INSIDE
CALL 1-800-319-6014 FOR SERVICE
RIGHT
FOOT
SWITCH
OR AUX IN
MM5
AUX
S
T
POWER
LEFT
FOOT
SWITCH
HEAD OR AUX IN
SET
TALK
ANT
TEK
BLUE
LAB
WHITE
BLACK
VITALINQ
94A07
YELLOW
SILVER
S
L
SECURITY
CABLE
36
Download PDF