User Manual
English
APC Smart-UPS®
5000 VA
208/230 Vac
Tower/Rack-Mount 5U
Uninterruptible Power Supply
990-8500
03/2007
Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
About this UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Unpack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Rack-mount configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Rack-mount to tower conversion procedure . . . . . . . . . . . . . . . . . . . . . . 4
Input hardwire 230 V models only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connect batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Configure bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connect display cable and install bezel . . . . . . . . . . . . . . . . . . . . . . . . . 7
Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connect Equipment and Power to the UPS . . . . . . . . . . . . . . . . . . . . . . . 8
Communication Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Emergency Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Display Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Display Panel Indicators and Function Buttons . . . . . . . . . . . . . . . . . . . 10
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
UPS settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Maintenance, Transport, and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Replace battery modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Two-Year Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
i
Introduction
About this UPS
The American Power Conversion (APC®) Uninterruptible Power Supply (UPS) provides protection for
electronic equipment from utility power blackouts, brownouts, sags and surges. The UPS filters small utility
line fluctuations and isolates electronic equipment from large disturbances by internally disconnecting from
utility line power. The UPS provides continuous power from the internal battery until utility power returns to
safe levels or the battery is fully discharged.
Unpack
Read the Safety Guide before installing the UPS.
Inspect the UPS upon receipt. Notify the carrier and dealer if there is damage.
The packaging is recyclable; save it for reuse or dispose of it properly.
The UPS and the battery modules are heavy. Remove the battery modules to lighten the UPS during
installation. Refer to battery removal instructions on the packaging.
Check the package contents:
•
•
•
•
•
•
•
•
UPS
Front bezel
Display bezel
Top covers (2) and one screw (tower
configuration)
EPO connector
Serial cable
Eight ornamental screws for securing
the unit in the rack
Four cage nuts
Hardware
8
• Two rack-mount brackets (used as
stabilizers in tower configuration)
• Eight pan-head locking screws
• Two rail cleats
• Eight pan-head screws
• Literature kit containing:
– Product documentation
– Smart-UPS® User Manuals CD
– PowerChute® Business Edition CD
– Safety information
– Warranty information
Additional contents for
230 V models:
– IEC power connector
– IEC jumper cables
pan head screws for securing rail cleats to UPS
8
pan head locking screws for securing rack-mount brackets/
stabilizer brackets to the UPS
1
pan head locking screw (black) for securing top covers to
UPS
8
ornamental screws for securing UPS to rack
4
cage nuts for rack installation
2
2
rack-mount brackets for rack-mount configuration
stabilizer brackets for tower configuration
rail cleats
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
1
Specifications
Temperature
Operating
Storage
Maximum
Elevation
Operating
Storage
This unit is intended for indoor use
only. Select a location sturdy enough
32° to 104° F (0° to 40° C)
to handle the weight.
5° to 86° F (-15° to 30° C) charge the UPS battery every six months
Do not operate the UPS where there
86° to 113° F (30° to 45° C) charge the UPS battery every three months
is excessive dust or the temperature
or humidity are outside the specified
limits.
Environmental factors impact battery
6562 ft (2,000 m)
life. High temperatures, poor utility
power, and frequent, short duration
50,000 ft (15,240 m)
discharges will shorten battery life.
Humidity
0 to 95% relative humidity, non-condensing
Weight
215 lbs (98 kg) with battery module
107 lbs (49 kg) without battery module
27 lbs (12 kg) each battery module
215 lbs (98 kg)
NOTE: The model and serial numbers are located on a small, rear panel label. For some models, an additional label
is located on the chassis under the front bezel.
Installation
Rack-mount configuration
This unit is intended for mounting in a four post rack. To order a two post rack-mount kit contact your dealer or
refer to the APC Web site, www.apc.com.
The UPS and the battery modules are heavy. Remove the battery modules to lighten the UPS during
installation. Refer to the battery removal instructions on the packaging.
Install rack-mount brackets and rail cleats
Four screws must be used to secure each rail bracket and rail cleat to the UPS. One rack-mount bracket and one
rail cleat must be secured to the both sides of the UPS.
Rack-mount bracket
four post rack-mount position
Rail cleat
4x
4x
2
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
Install unit in rack
Ensure rack stability prior to installing devices in the rack.
The UPS should be installed at or near the bottom of the rack.
When installing rails in the rack, install two cage nuts above each rail, (see diagram).
Secure the UPS in the rack using the four cage nuts and eight ornamental screws included in the package.
Second cage nut: count three
holes up from first cage nut
First cage nut: count four holes
up from top edge of rail
3 holes
3 holes
4 holes
4 holes
Install batteries
Connect only the first two batteries in the string of three batteries. Be sure that the battery
connectors are fully engages.
Do not connect the single battery or the last battery installed in the string of three batteries.
Close and secure battery doors
Foam spacers
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
4x
3
Rack-mount to tower conversion procedure
The UPS and the battery modules are heavy. Remove the battery modules to lighten the UPS during
installation. Refer to the battery removal instructions on the packaging.
Install stabilizer brackets
Stand the UPS on the side with the embossed marks.
Secure a stabilizer bracket (supplied), to both sides of the UPS.
Secure each bracket with two pan head locking screws (supplied).
4x
Install two top covers
Install the large top cover by placing it in the
slots on the UPS and sliding the cover
forward.
Install the small top cover by placing it in the
slots on the UPS and sliding the cover
forward.
Secure the top covers with a #8 black screw
(supplied).
Install batteries
Connect only the first two batteries in the string of three batteries. Be sure that the battery
connectors are fully engages.
Do not connect the single battery or the last battery installed in the string of three batteries.
Close and secure the battery doors
2x
Foam spacers
2x
4
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
Input hardwire 230 V models only
Hardwiring must be performed by a qualified electrician. Adhere to all national and local regulations.
1. Use a dedicated branch circuit with a maximum of 32 A of over-current protection, (either a circuit
breaker of fuses).
A lower rated branch may be used depending on the requirements of the UPS load.
Allow an additional 600 W for the UPS during the battery replacement procedure.
2. Switch the circuit breaker OFF prior to connecting equipment and power to the UPS.
3. Remove the access panels located on the rear panel of the UPS.
4. Remove the knockout from the input access panel.
5. Use # 10 AWG (5 mm²).
Strip approximately six inches (152.4 mm) of the outer jacket from the input cable exposing the wires.
Strip .5 inch (12.7 mm) of the individual wire coverings.
6. Route the input cable through the hole in the input access panel. Apply an appropriate strain relief.
7. Connect the ground wire prior to connecting the line wires.
8. Replace the access panels and secure each panel with three screws.
Terminal block
L1 L2/N
access panel
input
access panel
Access panel screws
Accessories
Install accessories prior to connecting power to the UPS.
Refer to the APC Web site, www.apc.com for available accessories.
•
•
Input/output hardwire kit
Two post rack option
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
5
Connect batteries
Rack-mount configuration
Tower configuration
Battery disconnect cord
Battery disconnect cord
After all of the batteries have been connected, tuck the battery cables and the battery disconnect cord in the
space provided in the battery doors. This will ensure a secure fit of the bezel to the unit.
Configure bezel
Snap the display out of the bezel. Rotate the bezel and reinstall the display for a tower configuration.
Display
6
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
Connect display cable and install bezel
Rack-mount configuration
Display cable
Tower configuration
Display cable
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
7
Start-up
Connect Equipment and Power to the UPS
1. The UPS features a chassis ground connection screw located on the rear panel, for connecting the ground
leads on transient voltage devices.
Prior to connecting the grounding wire, ensure that the UPS is NOT connected to utility or battery
power.
2. Connect equipment to the UPS.
3. 208 V models: Plug the UPS into a two-pole, three-wire, grounded receptacle only. Avoid using
extension cords.
230 V models: Refer to the Input Hardwire section in this manual.
4. To use the UPS as a master on/off switch be sure all connected equipment is switched on.
Rear Panels
208 V models
230 V models
Start the UPS
1. Press the
button on the front panel to start the UPS.
– The battery charges to 90% capacity during the first four hours of normal operation. Do not
expect full battery run capability during this initial charge period.
– Refer to the APC Web site, www.apc.com for battery runtimes.
2. For optimal computer system security, install PowerChute Smart-UPS monitoring software.
8
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
Communication Ports
SERIAL PORT
Use only the supplied cable to connect to the serial port. A standard serial
interface cable is incompatible with the UPS.
Emergency Power Off
The emergency power off (EPO) feature is user configurable. EPO provides immediate de-energizing of
connected equipment from a remote location, without switching to battery operation.
1. Use the EPO connector supplied with the UPS.
2. Use a normally-open contact to connect the +24 terminal to the IN terminal. External voltage is not
required.
3. Wire the four-pin connector to the EPO system.
EPO PORT
(located on rear panel)
EPO
Connector
The EPO interface is a Safety Extra Low Voltage (SELV) circuit. Connect it only to other SELV circuits.
The EPO interface monitors circuits that have no determined voltage potential. Such closure circuits
may be provided by a switch or relay properly isolated from the utility. To avoid damage to the UPS, do
not connect the EPO interface to any circuit other than a closure type circuit.
Use one of the following cable types to connect the UPS to the EPO switch.
•
•
•
•
•
•
CL2: Class 2 cable for general use.
CL2P: Plenum cable for use in ducts, plenums, and other spaces used for environmental air.
CL2R: Riser cable for use in a vertical run in a floor-to-floor shaft.
CLEX: Limited use cable for use in dwellings and for use in raceways.
For installation in Canada: Use only CSA certified, type ELC, (extra-low voltage control cable).
For installation in other countries: Use standard low-voltage cable in accordance with national and
local regulations.
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
9
Operation
Display Panels
208 V models
230 V models
Display Panel Indicators and Function Buttons
Indicator
LED
Indicator Title
Description
On Line
The UPS is supplying utility power to the connected equipment,
(see Troubleshooting).
AVR Trim
The UPS is compensating for a high utility voltage. Refer to the APC Web site,
www.apc.com for AVR settings.
AVR Boost
The UPS is compensating for a low utility voltage. Refer to the APC Web site,
www.apc.com for AVR settings.
On Battery
The UPS is supplying battery power to the connected equipment.
Overload
The connected equipment is drawing more than the UPS power rating allows,
(see Troubleshooting).
Replace Battery/Battery The battery is disconnected or must be replaced, (see Troubleshooting).
Disconnected
10
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
Indicator
LED
230 V
208 V
Indicator Title
Diagnostic
Utility Voltage
The UPS has a diagnostic feature that indicates the utility voltage.
The UPS starts a self-test as part of this procedure. The self-test does not affect the
voltage display.
Press and hold the
button to view the utility voltage bar graph indicator. As
soon as the on-line LED starts flashing indicating a self-test is in progress, the fiveLED Battery Charge indicator will show the utility input voltage.
Refer to the figure on the left for the voltage reading.
Values are not listed on the UPS.
The indicator on the UPS shows the voltage is between the displayed value on the
list and the next higher value, (see Troubleshooting).
Battery
Charge
Feature
Button
Description
Feature Title
Function
Power On
Press this button to turn on the UPS. Continue reading for additional
capabilities.
Self-Test
Automatic: The UPS performs a self-test automatically when tuned on, and
every two weeks thereafter (by default). During the self-test, the UPS
briefly operates the connected equipment on battery.
Manual: Press and hold the
self-test.
button for a few seconds to initiate the
Cold Start
When there is no utility power and the UPS is off, the cold start feature will
switch the UPS and connected equipment onto battery power,
(see Troubleshooting).
Power Off
Press this button to turn off the UPS.
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
11
Configuration
UPS settings
Settings are adjusted through PowerChute software or optional SmartSlot accessory cards.
Function
Factory
Default
User Selectable
Choices
Description
Automatic
Self-Test
On startup and
every 14 days
(336 hours)
there after
• On startup and every
7 days (168 hours)
there after
• On startup and every
14 days (336 hours)
there after
• On startup only
• No self-test
Set the interval at which the UPS will execute a
self-test.
UPS ID
UPS_IDEN
Up to eight characters
(alphanumeric)
Uniquely identify the UPS, (i.e. server name or
location) for network management purposes.
Date of Last
Battery
Replacement
Manufacture
Date
mm/dd/yy
Reset this date when you replace the battery
module.
Minimum Capacity
Before Return from
Shutdown
0 percent
•
•
•
•
Voltage Sensitivity
The UPS detects
and reacts to line
voltage distortions
by transferring to
battery operation to
protect the
connected
equipment.
High sensitivity
Alarm Delay
Control
Enable
• Enable
• Mute
• Disable
Shutdown Delay
90 seconds
•
•
•
•
12
0%
15%
30%
45%
• 60%
• 75%
• 90%
Brightly
illuminated: high
sensitivity
Dimly illuminated:
medium sensitivity
No illumination:
low sensitivity
0s
90 s
180 s
270 s
Specify the percentage to which batteries will
be charged following a low battery shutdown
before powering connected equipment.
Adjust by pressing the VOLTAGE SENSITIVIY
switch (rear panel). Use a pointed object, (such
as a pen) to do so.
Note: In situations of poor power quality, the
UPS may frequently transfer to battery
operation. If the connected equipment can
operate normally under such conditions, reduce
the sensitivity setting to conserve battery
capacity and service life.
Mute ongoing alarms or disable all alarms.
•
•
•
•
360 s
450 s
540 s
630 s
Set the interval between the time when the UPS
receives a shutdown command and actual
shutdown.
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
Function
Low Battery
Warning
PowerChute
software interface
provides automatic,
unattended
shutdown when
approximately two
minutes of battery
operated run time
remains.
Factory
Default
2 minutes
LED is located
on rear panel
Synchronized
Turn-on Delay
0 seconds
High Transfer Point
208 V models:
225 Vac
230 V models:
253 Vac
Low Transfer Point
208 V models:
182 Vac
230 V models:
208 Vac
Output Voltage
230 V models
User Selectable
Choices
Description
Brightly
illuminated:
low battery warning
level of about 2 minutes
Dimly illuminated:
low battery
warning level of about
5 minutes
No illumination:
low battery warning
level is about 8 minutes
The low-battery warning beeps are continuous
when two minutes of run time remain.
To change the default interval setting, use a
pointed object such as a pen to press the
VOLTAGE SENSITIVIY switch (rear panel),
while
•
•
•
•
Specify the time the UPS will wait after the
return of utility power before start up, (to avoid
branch circuit overload).
0s
60 s
120 s
180 s
•
•
•
•
240 s
300 s
360 s
420 s
• 225 Vac
• 229 Vac
• 233 Vac
237 Vac
• 253 Vac
• 257 Vac
• 261 Vac
• 265 Vac
•
• 182 Vac
• 178 Vac
•
• 174 Vac
• 170 Vac
• 196 Vac
• 200 Vac
• 204 Vac
• 208 Vac
• 220 Vac
• 230 Vac
• 240 Vac
pressing the
button, (front display).
Change the low battery warning interval setting
to the time that the operating system or system
software requires to safely shut down.
To avoid unnecessary use of the battery where
utility voltage is chronically high, set the high
transfer point higher if the connected
equipment can tolerate this condition.
To avoid unnecessary use of the battery where
utility voltage is chronically low, set the low
transfer point lower if the connected equipment
can tolerate this condition.
Set the output voltage of the UPS.
230 Vac
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
13
Troubleshooting
Use this chart to solve minor UPS installation and operation problems. Refer to www.apc.com for assistance
with complex UPS problems.
Problem and/or Possible Cause
Solution
UPS will not turn on
The battery is not connected properly.
button not pushed.
Check that the battery connector is fully engaged.
Press the
button once to power-up the UPS and connected equipment.
The UPS is not connected to utility
power supply.
Check that the power cable from the UPS to the utility power supply is
securely connected at both ends.
Very low or no utility voltage
Check the utility power supply to the UPS by plugging in a table lamp. If the
light is very dim, have the utility voltage checked.
UPS will not turn off
The UPS is experiencing an internal
fault
Do not attempt to use the UPS. Unplug the UPS and have it serviced
immediately.
UPS beeps occasionally
Normal UPS operation when running
on battery.
None: The UPS is protecting the connected equipment. Press the
to silence this alarm.
button
UPS is not providing expected backup time
The UPS battery(s) are weak due to a
recent power outage or battery(s) are
near the end of their service life.
Charge the battery(s). Batteries require recharging after extended outages.
Batteries can wear faster when put into service often or when operated at
elevated temperatures. If the battery(s) are near the end of their service life,
consider replacing the battery(s) even if the replace battery LED is not yet
illuminated.
All LEDs are illuminated and the UPS emits a constant beeping
The UPS is experiencing an internal
fault.
Do not attempt to use the UPS. Unplug the UPS and have it serviced
immediately.
Front panel LEDs flash sequentially
The UPS has been shut down remotely
through software or an optional
accessory card.
None: The UPS will restart automatically when utility power returns.
All LEDs are off and the UPS is plugged into a wall outlet
The UPS is shut down or the battery is
discharged from an extended outage.
14
None: The UPS will restart automatically when utility power is restored and
the battery has a sufficient charge.
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
Problem and/or Possible Cause
Solution
The Overload LED is illuminated and the UPS emits a sustained alarm tone
The UPS is overloaded.
The connected equipment exceeds the specified “maximum load” as defined
in Specifications on the APC Web site, www.apc.com.
The alarm remains on until the overload is removed. Disconnect nonessential
equipment from the UPS to eliminate the overload condition.
The UPS continues to supply power as long as it is online and the circuit
breaker does not trip; the UPS will not provide power from batteries in the
event of a utility voltage interruption.
The Replace Battery/Battery Disconnected LED is illuminated
The Replace Battery/Battery
Disconnected LED flashes and a short
beep is emitted every two seconds to
indicate the battery is disconnected.
Check that the battery connectors are fully engaged.
Weak battery
Allow the battery to recharge for 24 hours and perform a self-test. If the
problem persists after recharging, replace the battery.
Failure of a battery self-test: Replace
Battery/Battery Disconnected LED
illuminates and the UPS emits short
beeps for one minute. The UPS repeats
the alarm every five hours.
Allow the battery to recharge for 24 hours. Perform the self-test procedure to
confirm the replace battery condition. The alarm stops and the LED clears if
the battery passes the self-test.
If the battery fails again, it must be replaced. The connected equipment is
unaffected.
The input circuit breaker trips
The connected equipment exceeds the
specified “maximum load” as defined
in Specifications on the APC Web site,
www.apc.com.
Unplug all nonessential equipment from the UPS.
Reset the circuit breaker.
The AVR Boost or AVR Trim LEDs are illuminated
The system is experiencing very high or
low utility voltage.
Have a qualified service personnel check your facility for electrical
problems. If the problem persists, contact the utility company for further
assistance.
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
15
Problem and/or Possible Cause
Solution
There is no utility power
There is no utility power and the UPS is
off.
Use the cold start feature to supply power to the connected equipment front
the UPS battery(s).
Press and hold the
button. There will be a short beep followed by a
longer beep. Release the button during the second beep.
UPS operates on battery although line voltage exists
The UPS input circuit breaker trips.
Unplug all nonessential equipment from the UPS.
Reset the circuit breaker.
Your system is experiencing very high,
low or distorted line voltage.
Move the UPS to a different outlet on a different circuit: Inexpensive fuel
powered generators may distort the voltage. Test the input voltage with the
utility voltage display, (see Operation). If acceptable to the connected
equipment, reduce the UPS sensitivity.
Battery Charge and Load LEDs flash simultaneously
The UPS has shut down.
The internal temperature of the UPS has
exceeded the allowable threshold for
safe operation.
Check that the room temperature is within the specified limits for operation.
Check that the UPS is properly installed, allowing for adequate ventilation.
Allow the UPS to cool down. Restart the UPS. If the problem persists,
contact APC at www.apc.com.
Diagnostic utility voltage
All five LEDs are illuminated.
The line voltage is extremely high and should be checked by an electrician.
There is no LED illumination.
The line voltage is extremely low and should be checked by an electrician.
On Line LED
There is no LED illumination.
The UPS is running on battery, or it must be turned on.
The LED is blinking.
The UPS is running an internal self-test.
16
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
Maintenance, Transport, and Service
Replace battery modules
This UPS has easy-to-replace, hot-swappable battery modules. Replacement is a safe procedure, isolated from
electrical hazards. You may leave the UPS in the rack and connected equipment on during the replacement
procedure.
Once the batteries are disconnected the connected equipment is not protected from power outages.
Refer to the appropriate replacement battery user manual for battery module installation instructions. See your
dealer or contact APC at www.apc.com for information on replacement battery modules.
Be sure to deliver the spent battery(s) to a recycling facility or ship it to APC in the
replacement battery packing material.
Open battery doors
4x
Remove spent batteries from the UPS
Pull the battery disconnect cords
attached to the battery connectors.
DO NOT pull the battery cables to
disconnect the batteries.
Battery
disconnect
cord
Install new batteries
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
17
Service
If the UPS requires service do not return it to the dealer. Follow these steps:
1. Review the problems discussed in Troubleshooting to eliminate common problems.
2. If the problem persists, contact APC Customer Support through the
APC Web site, www.apc.com.
– Note the model number of the UPS, the serial number located on the back of the unit, and the date
purchased. If you call APC Customer Support, a technician will ask you to describe the problem
and attempt to solve it over the phone. If this is not possible, the technician will issue a Returned
Material Authorization Number (RMA#).
– If the UPS is under warranty, repairs are free.
– Procedures for servicing or returning products may vary internationally. Refer to the APC Web
site for country specific instructions.
3. Pack the UPS in its original packaging. If this is not available:
– Pack the UPS carefully to avoid damage in transit. Never use Styrofoam beads for packaging.
– Damage sustained in transit is not covered under warranty.
4. Always DISCONNECT THE UPS BATTERY before shipping in compliance with U.S. Department
of Transportation (DOT) and IATA regulations. The battery may remain in the UPS.
5. Mark the RMA# on the outside of the package.
6. Return the UPS by insured, prepaid carrier to the address given to you by Customer Support.
18
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
Two-Year Warranty
The limited warranty provided by American Power Conversion (APC®) in this statement of Limited Factory Warranty applies only to
products you purchase for your commercial or industrial use in the ordinary course of your business.
Terms of warranty
APC warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase. The
obligation of APC under this warranty is limited to repairing or replacing, at its sole discretion, any such defective products. This warranty
does not apply to equipment that has been damaged by accident, negligence or misapplication or has been altered or modified in any way.
Repair or replacement of a defective product or part thereof does not extend the original warranty period. Any parts furnished under this
warranty may be new or factory-remanufactured.
Non-transferable warranty
This warranty extends only to the original purchaser who must have properly registered the product. The product may be registered at the
APC Web site, www.apc.com.
Exclusions
APC shall not be liable under the warranty if its testing and examination disclose that the alleged defect in the product does not exist or was
caused by end user or any third person misuse, negligence, improper installation or testing. Further, APC shall not be liable under the
warranty for unauthorized attempts to repair or modify wrong or inadequate electrical voltage or connection, inappropriate on-site
operation conditions, corrosive atmosphere, repair, installation, start-up by non-APC designated personnel, a change in location or
operating use, exposure to the elements, Acts of God, fire, theft, or installation contrary to APC recommendations or specifications or in
any event if the APC serial number has been altered, defaced, or removed, or any other cause beyond the range of the intended use.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BY OPERATION OF LAW OR OTHERWISE, OF PRODUCTS SOLD,
SERVICED OR FURNISHED UNDER THIS AGREEMENT OR IN CONNECTION HEREWITH. APC DISCLAIMS ALL IMPLIED
WARRANTIES OF MERCHANTABILITY, SATISFACTION AND FITNESS FOR A PARTICULAR PURPOSE. APC EXPRESS
WARRANTIES WILL NOT BE ENLARGED, DIMINISHED, OR AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL
ARISE OUT OF, APC RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN CONNECTION WITH THE
PRODUCTS. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER
WARRANTIES AND REMEDIES. THE WARRANTIES SET FORTH ABOVE CONSTITUTE APC SOLE LIABILITY AND
PURCHASER EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTIES. APC WARRANTIES EXTEND ONLY TO
PURCHASER AND ARE NOT EXTENDED TO ANY THIRD PARTIES.
IN NO EVENT SHALL APC, ITS OFFICERS, DIRECTORS, AFFILIATES OR EMPLOYEES BE LIABLE FOR ANY FORM OF
INDIRECT, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, ARISING OUT OF THE USE, SERVICE OR
INSTALLATION, OF THE PRODUCTS, WHETHER SUCH DAMAGES ARISE IN CONTRACT OR TORT, IRRESPECTIVE OF
FAULT, NEGLIGENCE OR STRICT LIABILITY OR WHETHER APC HAS BEEN ADVISED IN ADVANCE OF THE POSSIBILITY
OF SUCH DAMAGES. SPECIFICALLY, APC IS NOT LIABLE FOR ANY COSTS, SUCH AS LOST PROFITS OR REVENUE, LOSS
OF EQUIPMENT, LOSS OF USE OF EQUIPMENT, LOSS OF SOFTWARE, LOSS OF DATA, COSTS OF SUBSTITUENTS, CLAIMS
BY THIRD PARTIES, OR OTHERWISE.
NO SALESMAN, EMPLOYEE OR AGENT OF APC IS AUTHORIZED TO ADD TO OR VARY THE TERMS OF THIS WARRANTY.
WARRANTY TERMS MAY BE MODIFIED, IF AT ALL, ONLY IN WRITING SIGNED BY AN APC OFFICER AND LEGAL
DEPARTMENT.
Warranty claims
Customers with warranty claims issues may access the APC customer support network through the Support page of the APC Web site,
www.apc.com/support. Select your country from the country selection pull-down menu. Open the Support tab at the top of the Web page to
obtain contact information for customer support in your region.
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
19
Regulatory Information
Regulatory Agency Approvals, Radio Frequency Warnings, Declaration of Conformity
FCC Compliance Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the
instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case users will be required to take whatever measures may be necessary to correct the interference at
their own expense.
208 V models
LISTED 42C2
E95463
230 V models
N 394
geprüf te
Sich erh eit
APC Worldwide Customer Support
Customer support for this or any other APC product is available at no charge in any of the following ways:
•
Refer to the APC Web site to access documents in the APC Knowledge Base and to submit customer
support requests.
– www.apc.com (Corporate Headquarters)
Connect to localized APC Web sites for specific countries, each of which provides customer
support information.
– www.apc.com/support/
Global support searching APC Knowledge Base and using e-support.
• Contact an APC Customer Support center by telephone or e-mail.
Local, country-specific centers:
go to www.apc.com/support/contact for information.
Contact the APC representative or other distributor from whom you purchased your APC product for
information on how to obtain local customer support.
Entire contents copyright 2007 American Power Conversion Corporation. All rights reserved. Reproduction in whole or in part without
permission is prohibited.
APC, the APC logo, Smart-UPS and PowerChute are trademarks of American Power Conversion Corporation. All other trademarks,
product names, and corporate names are the property of their respective owners and are used for informational purposes only.
20
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
Date of product declaration
Smart-UPS 5000 VA 208/230 Vac Tower/Rack-Mount 5U User Manual
21
Download PDF