Daikin | ATXS20G2V1B | Operation Manual

00_CV_3P207037-2D.fm Page 1 Wednesday, March 11, 2009 9:15 AM
DAIKIN ROOM AIR CONDITIONER
Operation Manual
MODELS ATXS20G2V1B
ATXS25G2V1B
ATXS35G2V1B
ATXS42G2V1B
ATXS50G2V1B
English
Deutsch
Français
Nederlands
Español
Italiano
ΕλληνικÜ
Portugues
01_EN_3P207037-2D.fm Page 1 Friday, March 13, 2009 9:39 AM
CONTENTS
READ BEFORE OPERATION
Safety precautions ......................................... 2
Names of parts............................................... 4
Preparation Before Operation ........................ 7
OPERATION
AUTO · DRY · COOL · HEAT · FAN
Operation ..................................................... 10
Adjusting the Airflow Direction ..................... 12
COMFORT AIRFLOW Operation ................. 14
INTELLIGENT EYE Operation ..................... 15
POWERFUL Operation ................................ 17
OUTDOOR UNIT QUIET Operation............. 18
ECONO Operation ....................................... 19
TIMER Operation ......................................... 20
Note for Multi System................................... 22
CARE
Care and Cleaning ....................................... 24
TROUBLE SHOOTING
Trouble Shooting.......................................... 27
1
01_EN_3P207037-2D.fm Page 2 Friday, March 13, 2009 9:39 AM
Safety precautions
READ BEFORE OPERATION
•
•
•
•
Keep this manual where the operator can easily find them.
Read this manual attentively before starting up the unit.
For safety reason the operator must read the following cautions carefully.
This manual classifies precautions into WARNING and CAUTION. Be sure to follow all precautions below: they are all
important for ensuring safety.
WARNING
CAUTION
If you do not follow these instructions exactly, the unit may If you do not follow these instructions exactly, the unit may
cause property damage, personal injury or loss of life.
cause minor or moderate property damage or personal injury.
Never do.
Be sure to follow the instructions.
Be sure to earth the air conditioner.
Never cause the air conditioner (including the remote
controller) to get wet.
Never touch the air conditioner (including the remote
controller) with a wet hand.
WARNING
• In order to avoid fire, explosion or injury, do not operate the unit when harmful, among which flammable or
corrosive gases, are detected near the unit.
• It is not good for health to expose your body to the air flow for a long time.
• Do not put a finger, a rod or other objects into the air outlet or inlet. As the fan is rotating at a high speed, it will
cause injury.
• Do not attempt to repair, relocate, modify or reinstall the air conditioner by yourself. Incorrect work will cause electric
shocks, fire etc.
For repairs and reinstallation, consult your Daikin dealer for advice and information.
• The refrigerant used in the air conditioner is safe. Although leaks should not occur, if for
some reason any refrigerant happens to leak into the room, make sure it does not come in
contact with any flame as of gas heaters, kerosene heaters or gas range.
• If the air conditioner is not cooling (heating) properly, the refrigerant may be leaking, so call your dealer.
When carrying out repairs accompanying adding refrigerant, check the content of the repairs with our service staff.
• Do not attempt to install the air conditioner by your self. Incorrect work will result in water leakage, electric shocks or
fire. For installation, consult the dealer or a qualified technician.
• In order to avoid electric shock, fire or injury, if you detect any abnormally such as smell of fire, stop the operation and
turn off the breaker. And call your dealer for instructions.
• Depending on the environment, an earth leakage breaker must be installed. Lack of an earth leakage breaker may
result in electric shocks or fire.
• The air conditioner must be earthed. Incomplete earthing may result in electric shocks. Do not connect the
earth line to a gas pipe, water pipe, lightning rod, or a telephone earth line.
CAUTION
• In order to avoid any quality deterioration, do not use the unit for cooling precision instruments, food, plants,
animals or works of art.
• Never expose little children, plants or animals directly to the air flow.
• Do not place appliances which produce open fire in places exposed to the air flow from the unit or under the
indoor unit. It may cause incomplete combustion or deformation of the unit due to the heat.
2
01_EN_3P207037-2D.fm Page 3 Friday, March 13, 2009 9:39 AM
• Do not block air inlets nor outlets. Impaired air flow may result in insufficient performance or trouble.
• Do not stand or sit on the outdoor unit. Do not place any object on the unit to avoid injury, do not remove the fan guard.
• Do not place anything under the indoor or outdoor unit that must be kept away from moisture. In certain conditions,
moisture in the air may condense and drip.
• After a long use, check the unit stand and fittings for damage.
• Do not touch the air inlet and aluminum fins of outdoor unit. It may cause injury.
• The appliance is not intended for use by young children or infirm persons without supervision.
• Young children should be supervised to ensure that they do not play with the appliance.
• To avoid oxygen deficiency, ventilate the room sufficiently if equipment with burner is used together with the
air conditioner.
• Before cleaning, be sure to stop the operation, turn the breaker off or pull out the supply cord.
• Do not connect the air conditioner to a power supply different from the one as specified. It may cause trouble or fire.
• Arrange the drain hose to ensure smooth drainage. Incomplete draining may cause wetting of the building, furniture
etc.
• Do not place objects in direct proximity of the outdoor unit and do not let leaves and other debris accumulate around
the unit.
Leaves are a hotbed for small animals which can enter the unit. Once in the unit, such animals can cause malfunctions, smoke or fire when making contact with electrical parts.
• Do not operate the air conditioner with wet hands.
• Do not wash the indoor unit with excessive water, only use a slightly wet cloth.
• Do not place things such as vessels containing water or anything else on top of the unit. Water may penetrate into the unit and degrade electrical insulations, resulting in an electric shock.
Installation site.
„ To install the air conditioner in the following types of environments, consult the dealer.
• Places with an oily ambient or where steam or soot occurs.
• Salty environment such as coastal areas.
• Places where sulfide gas occurs such as hot springs.
• Places where snow may block the outdoor unit.
The drain from the outdoor unit must be discharged to a place of good drainage.
Consider nuisance to your neighbours from noises.
„ For installation, choose a place as described below.
• A place solid enough to bear the weight of the unit which does not amplify the operation noise or vibration.
• A place from where the air discharged from the outdoor unit or the operation noise will not annoy
your neighbours.
Electrical work.
• For power supply, be sure to use a separate power circuit dedicated to the air conditioner.
System relocation.
• Relocating the air conditioner requires specialized knowledge and skills. Please consult the dealer if relocation is necessary for moving or remodeling.
3
01_EN_3P207037-2D.fm Page 4 Friday, March 13, 2009 9:39 AM
Names of parts
„ Indoor Unit
1
2
3
4
5
7
10
11
6
9
8
16
14
13
15
12
4
01_EN_3P207037-2D.fm Page 5 Friday, March 13, 2009 9:39 AM
„ Outdoor Unit
20/25/35/42 class
50 class
17
17
19
19
20
20
21
18
18
21
„
Indoor Unit
1. Air filter
2. Titanium Apatite Photocatalytic
Air-Purifying Filter:
• These filters are attached to the inside of the air
filters.
3. Air inlet
4. Front panel
5. Panel tab
6. Room temperature sensor:
• It senses the air temperature around the unit.
7. INTELLIGENT EYE sensor:
• It detects the movements of people and automatically switches between normal operation
and energy saving operation. (page 15.)
8. Display
9. Air outlet
10. Flaps (horizontal blades): (page 12.)
11. Louvers (vertical blades):
• The louvers are inside of the air outlet.
(page 12.)
12. Indoor Unit ON/OFF switch: (page 10.)
• Push this switch once to start operation.
Push once again to stop it.
• The operation mode refers to the following
table.
Mode
AUTO
Temperature
setting
25°C
Airflow rate
AUTO
• This switch is useful when the remote controller
is missing.
13. Operation lamp (green)
14. TIMER lamp (yellow): (page 20.)
15. INTELLIGENT EYE lamp (green): (page 15.)
16. Signal receiver:
• It receives signals from the remote controller.
• When the unit receives a signal, you will hear a
short beep.
• Operation start .............beep-beep
• Settings changed..........beep
• Operation stop ..............beeeeep
„ Outdoor Unit
17. Air inlet: (Back and side)
20. Drain hose
18. Air outlet
21. Earth terminal:
• It is inside of this cover.
19. Refrigerant piping and inter-unit cable
5
01_EN_3P207037-2D.fm Page 6 Friday, March 13, 2009 9:39 AM
„ Remote Controller
1
R
2
5
ECONO
ON/OFF
3
POWERFUL
TEMP
6
4
7
MODE
QUIET
9
10
FAN
COMFORT
SWING
8
11
SENSOR
13
ON
CANCEL
12
16
OFF
TIMER
15
18
17
14
<ARC433A85>
1. Signal transmitter:
• It sends signals to the indoor unit.
2. Display:
• It displays the current settings.
(In this illustration, each section is shown with all
its displays ON for the purpose of explanation.)
3. ECONO button:
ECONO operation (page 19.)
4. POWERFUL button:
POWERFUL operation (page 17.)
5. TEMPERATURE adjustment buttons:
• It changes the temperature setting.
6. ON/OFF button:
• Press this button once to start operation.
Press once again to stop it.
7. MODE selector button:
• It selects the operation mode.
(AUTO/DRY/COOL/HEAT/FAN) (page 10.)
6
8. QUIET button: OUTDOOR UNIT QUIET
operation (page 18.)
9. FAN setting button:
• It selects the airflow rate setting.
10. SWING button:
• Ajusting the Airflow Direction. (page 12.)
11. SWING button:
• Louvers (vertical blades) (page 12.)
12. COMFORT/SENSOR button:
• COMFORT AIRFLOW and INTELLIGENT
EYE operation (page 14, 15.)
13. ON TIMER button: (page 21.)
14. OFF TIMER button: (page 20.)
15. TIMER Setting button:
• It changes the time setting.
16. TIMER CANCEL button:
• It cancels the timer setting.
17. CLOCK button: (page 9.)
18. RESET button:
• Restart the unit if it freezes.
• Use a thin object to push.
01_EN_3P207037-2D.fm Page 7 Friday, March 13, 2009 9:39 AM
Preparation Before Operation
„ To set the batteries
1. Slide the front cover to take it off.
Position + and
– correctly!
2
2. Set two dry batteries AAA.LR03
(alkaline).
–
+
+
–
3. Set the front cover as before.
3
1
ATTENTION
„ About batteries
• When replacing the batteries, use batteries of the same type, and replace the two old batteries
together.
• When the system is not used for a long time, take the batteries out.
• The batteries will last for approximately one year. If the remote controller display begins to fade and
the degradation of reception performance occurs within a year, however, replace both two batteries
with new size AAA.LR03(alkaline).
• The attached batteries are provided for the initial use of the system.
The usable period of the batteries may be short depending on the manufactured date of the air
conditioner.
7
01_EN_3P207037-2D.fm Page 8 Friday, March 13, 2009 9:39 AM
Preparation Before Operation
„ To operate the remote
controller
• To use the remote controller, aim the transmitter
at the indoor unit. If there is anything to block
signals between the unit and the remote controller, such as a curtain, the unit will not operate.
• Do not drop the remote controller. Do not get it wet.
• The maximum distance for communication is
about 7m.
Receiver
„ To fix the remote controller
holder on the wall
1. Choose a place from where the signals reach the unit.
R
2. Fix the holder to a wall, a pillar, or
similar location with the screws
procured locally.
3. Place the remote controller in the
remote controller holder.
Remote controller
holder
Set.
l To remove, pull it upwards.
ATTENTION
„ About remote controller
• Never expose the remote controller to direct sunlight.
• Dust on the signal transmitter or receiver will reduce the sensitivity. Wipe off dust with soft cloth.
• Signal communication may be disabled if an electronic-starter-type fluorescent lamp (such as
inverter-type lamps) is in the room. Consult the shop if that is the case.
• If the remote controller signals happen to operate another appliance, move that appliance to somewhere else, or consult the shop.
8
01_EN_3P207037-2D.fm Page 9 Friday, March 13, 2009 9:39 AM
„ To set the clock
R
1. Press “CLOCK button”.
is displayed.
blinks.
2. Press “TIMER setting button” to
set the clock to the present time.
Holding down “
” or “
” button
rapidly increases or decreases the time
display.
ECONO
POWERFUL
ON/OFF
TEMP
3. Press “CLOCK button”.
blinks.
MODE
QUIET
„ Turn the breaker ON
• Turning ON the breaker opens once and
closes the flaps. (This is a normal procedure.)
FAN
COMFORT
SWING
2
SENSOR
ON
CANCEL
1, 3
OFF
TIMER
NOTE
„ Tips for saving energy
• Be careful not to cool (heat) the room too much.
Keeping the temperature setting at a moderate level helps save energy.
• Cover windows with a blind or a curtain.
Blocking sunlight and air from outdoors increases the cooling (heating) effect.
• Clogged air filters cause inefficient operation and waste energy. Clean them
once in about every two weeks.
Recommended temperature setting
For cooling: 26°C – 28°C
For heating: 20°C – 24°C
„ Please note
• The outdoor unit consumes some power to have its electric components work even while it is not operating.
Connecting outdoor unit ARXS20/25/35/42 : 1-15W
Other outdoor units : 15-20W
The outdoor unit consumes 40 to 55W of power at the time of compressor preheating.
• If you are not going to use the air conditioner for a long period, for example in spring or autumn, turn the breaker OFF.
• Use the air conditioner in the following conditions.
Mode
COOL
HEAT
DRY
Operating conditions
Outdoor temperature: 〈2AMX〉 10 to 46°C
〈3AMX〉 –10 to 46°C
〈ARXS〉 –10 to 46°C
Indoor temperature: 18 to 32°C
Indoor humidity: 80% max.
Outdoor temperature: 〈2AMX〉 –15 to 20°C
〈3AMX〉 –15 to 20°C
〈ARXS〉 –15 to 20°C
Indoor temperature: 10 to 30 °C
Outdoor temperature: 〈2AMX〉 10 to 46°C
〈3AMX〉 –10 to 46°C
〈ARXS〉 –10 to 46°C
Indoor temperature: 18 to 32°C
Indoor humidity: 80% max.
If operation is continued out of this range
• A safety device may work to stop the operation.
(In multi system, it may work to stop the operation of the outdoor unit only.)
• Condensation may occur on the indoor unit and drip.
• A safety device may work to stop the operation.
• A safety device may work to stop the operation.
• Condensation may occur on the indoor unit and drip.
• The operation of the system outside the above humidity or temperature range may cause a safety device to disable the system.
9
01_EN_3P207037-2D.fm Page 10 Friday, March 13, 2009 9:39 AM
AUTO · DRY · COOL · HEAT · FAN Operation
OPERATION
The air conditioner operates with the operation mode of your
choice.
From the next time on, the air conditioner will operate with the
same operation mode.
R
„ To start operation
1. Press “MODE selector button”
and select a operation mode.
• Each pressing of the button advances the
mode setting in sequence.
: AUTO
4
ECONO
ON/OFF
TEMP
POWERFUL
2, 3
1
: DRY
: COOL
MODE
: HEAT
QUIET
FAN
COMFORT
: FAN
SWING
5
SENSOR
ON
CANCEL
OFF
TIMER
2. Press “ON/OFF button” .
• The OPERATION lamp lights up.
„ To stop operation
3. Press “ON/OFF button” again.
• Then OPERATION lamp goes off.
„ To change the temperature setting
4. Press “TEMPERATURE adjustment button”.
DRY or FAN mode
AUTO or COOL or HEAT mode
Press “
“
The temperature setting is not variable.
” to raise the temperature and press
” to lower the temperature.
Set to the temperature you like.
C
10
01_EN_3P207037-2D.fm Page 11 Friday, March 13, 2009 9:39 AM
„ To change the airflow rate setting
5. Press “FAN setting button”.
DRY mode
AUTO or COOL or HEAT or FAN mode
Five levels of airflow rate setting from “
The airflow rate setting is not variable.
plus “
”“
” to “
”
” are available.
• Indoor unit quiet operation
When the airflow is set to “ ”, the noise from the indoor unit will become quieter.
Use this when making the noise quieter.
NOTE
„ Note on HEAT operation
• Since this air conditioner heats the room by taking heat from outdoor air to indoors, the heating
capacity becomes smaller in lower outdoor temperatures. If the heating effect is insufficient, it
is recommended to use another heating appliance in combination with the air conditioner.
• The heat pump system heats the room by circulating hot air around all parts of the room.
After the start of heating operation, it takes some time before the room gets warmer.
• In heating operation, frost may occur on the outdoor unit and lower the heating capacity. In
that case, the system switches into defrosting operation to take away the frost.
• During defrosting operation, hot air does not flow out of indoor unit.
• A pinging sound may be heard during defrosting operation, which, however does not mean
that the air conditioner has failures.
„ Note on COOL operation
• This air conditioner cools the room by blowing the hot air in the room outside, so if the
outside temperature is high, the performance of the air conditioner drops.
„ Note on DRY operation
• The computer chip works to rid the room of humidity while maintaining the temperature as
much as possible. It automatically controls temperature and airflow rate, so manual
adjustment of these functions is unavailable.
„ Note on AUTO operation
• In AUTO operation, the system selects a temperature setting and an appropriate operation
mode (COOL or HEAT) based on the room temperature at the start of the operation.
• The system automatically reselects setting at a regular interval to bring the room
temperature to user-setting level.
• If you do not like AUTO operation, manually change the set temperature.
„ Note on airflow rate setting
• At smaller airflow rates, the cooling (heating) effect is also smaller.
11
01_EN_3P207037-2D.fm Page 12 Friday, March 13, 2009 9:39 AM
Adjusting the Airflow Direction
You can adjust the airflow direction to increase your comfort.
„ To adjust the horizontal
blades (flaps)
R
1. Press “SWING button”.
• “
” is displayed on the LCD and the flaps
will begin to swing.
2. When the flaps have reached the
desired position, press “SWING
button” once more.
ECONO
POWERFUL
ON/OFF
TEMP
• The flaps will stop moving.
• “
” disappears from the LCD.
MODE
QUIET
1, 2
FAN
COMFORT
SWING
3, 4
SENSOR
ON
CANCEL
OFF
TIMER
„ To adjust the vertical blades (louvers)
3. Press “SWING button
• “
”.
” is displayed on the LCD.
4. When the louvers have reached the desired position, press the
“SWING button
” once more.
• The louvers will stop moving.
• “
” disappears from the LCD.
12
01_EN_3P207037-2D.fm Page 13 Friday, March 13, 2009 9:39 AM
„ To start 3-D Airflow
1. 3. Press the “SWING button
” and the “SWING button
”:
the “ ” and “
” display will light up and the flap and louvers will
move in turn.
„ To cancel 3-D Airflow
2. 4. Press either the “SWING button
” or the “SWING button
”.
Notes on flaps and louvers angles
• When “SWING button” is selected, the flaps
swinging range depends on the operation mode.
(See the figure.)
Three-Dimensional (3-D) Airflow
• Using three-dimensional airflow circulates
cold air, which tends to collected at the
bottom of the room, and hot air, which tends
to collect near the ceiling, throughout the
room, preventing areas of cold and hot
developing.
„ ATTENTION
• Always use a remote controller to adjust the
angles of the flaps and louvers. If you
attempt to move it forcibly with hand when it
is swinging, the mechanism may be broken.
• Always use a remote controller to adjust the
louvers angles. In side the air outlet, a fan is
rotating at a high speed.
In DRY mode or
COOL mode
COMFORT AIRFLOW 5˚
(page 14.)
15˚
Upper limit 50˚
Lower limit
Stop operation
In HEAT mode
Stop operation
30˚
Upper limit 70˚
Lower limit
80˚
COMFORT AIRFLOW (page 14.)
In FAN mode
Upper limit
5˚
80˚
Lower limit
Stop operation
13
01_EN_3P207037-2D.fm Page 14 Friday, March 13, 2009 9:39 AM
COMFORT AIRFLOW Operation
The flow of air will be in the upward direction while in
cooling mode and in the downward direction while in
heating mode, which will provide a comfortable wind
that will not come in direct contact with people.
R
„ To start COMFORT
AIRFLOW operation
1. Press “COMFORT/SENSOR button”
and select “ ” on the LCD.
• Each time the “COMFORT/SENSOR
button” is pressed a different setting option
is displayed on the LCD.
• By selecting “
” from the following
icons, the air conditioner will be in COMFORT
AIRFLOW operation combined with
INTELLIGENT EYE operation. (page 16.)
ECONO
POWERFUL
MODE
QUIET
ON/OFF
TEMP
FAN
COMFORT
SWING
1, 2
SENSOR
Blank
ON
CANCEL
OFF
„ To cancel COMFORT
AIRFLOW operation
TIMER
2. Press “COMFORT/SENSOR button”.
• Press the button to select “Blank”.
Notes on “COMFORT AIRFLOW Operation”
• The flap position will change, preventing air from blowing directly on the occupants of the room.
• POWERFUL operation and COMFORT AIRFLOW operation cannot be used at the same time.
• The volume of air will be set to AUTO. If the upward and downward airflow direction is
selected, the COMFORT AIRFLOW function will be canceled.
• Priority is given to the function of whichever button is pressed last.
• The COMFORT AIRFLOW function makes the following airflow direction adjustments.
The flaps will move upward while cooling so that the airflow will be directed upward.
The flaps will move downward while heating so that the airflow will be directed downward.
Cooling operation
14
Heating operation
01_EN_3P207037-2D.fm Page 15 Friday, March 13, 2009 9:39 AM
INTELLIGENT EYE Operation
“INTELLIGENT EYE” is the infrared sensor which
detects the human movement.
R
„ To start INTELLIGENT EYE
operation
1. Press “COMFORT/SENSOR button”
and select “ ” on the LCD.
• Each time the “COMFORT/SENSOR
button” is pressed a different setting option
is displayed on the LCD.
• By selecting “
” from the following
icons, the air conditioner will be in COMFORT
AIRFLOW operation combined with
INTELLIGENT EYE operation. (page 16.)
Blank
ECONO
POWERFUL
MODE
QUIET
ON/OFF
TEMP
FAN
COMFORT
SWING
1, 2
SENSOR
„ To cancel the INTELLIGENT
EYE operation
ON
CANCEL
OFF
TIMER
2. Press “COMFORT/SENSOR button”.
• Press the button to select “Blank”.
[EX.]
When somebody in the room
• Normal operation
The air conditioner is in normal
operation while the sensor is
detecting the movement of people.
When nobody in the room
• 20 min. after, start energy
saving operation.
The set temperature is shifted in
±2ºC steps.
Somebody back in the room
• Back to normal operation.
The air conditioner will return to
normal operation when the sensor
detects the movement of people
again.
15
01_EN_3P207037-2D.fm Page 16 Friday, March 13, 2009 9:39 AM
INTELLIGENT EYE Operation
“INTELLIGENT EYE” is useful for Energy Saving
„ Energy saving operation
• Change the temperature –2°C in heating / +2°C in cooling / +2°C in dry mode from set temperature.
• Decrease the airflow rate slightly in FAN mode only. If no presence detected in the room for
20 minutes.
Notes on “INTELLIGENT EYE”
• Application range is as follows.
Vertical angle 90˚
(Side View)
Horizontal angle 110˚
(Top View)
7m
55˚ 55˚
7m
90˚
• Sensor may not detect moving objects further than 7m away. (Check the application range)
• Sensor detection sensitivity changes according to indoor unit location, the speed of
passersby, temperature range, etc.
• The sensor also mistakenly detects pets, sunlight, fluttering curtains and light reflected off of
mirrors as passersby.
• INTELLIGENT EYE operatipon will not go on during powerful operation.
• NIGHT SET MODE (page 20.) will not go on during use of INTELLIGENT EYE operation.
„ To combine “COMFORT AIRFLOW Operation” and
“INTELLIGENT EYE Operation”
1. Press “COMFORT/SENSOR button” and select “
” on the LCD.
• Each time the “COMFORT/SENSOR button” is pressed a different setting option is
displayed on the LCD.
Blank
2. Press “COMFORT/SENSOR button”.
• Press the button to select “Blank”.
• The air conditioner can go into operation with the COMFORT AIRFLOW and INTELLIGENT
EYE functions combined.
• The volume of air will be set to AUTO. If the upward and downward airflow direction is
selected, the CONFORT AIRFLOW operation will be canceled.
Priority is given to the function of whichever button is pressed last.
CAUTION
• Do not place large objects near the sensor.
Also keep heating units or humidifiers outside the sensor’s detection area. This sensor can
detect undesirable objects.
• Do not hit or violently push the INTELLIGENT EYE sensor. This can lead to damage and
malfunction.
16
01_EN_3P207037-2D.fm Page 17 Friday, March 13, 2009 9:39 AM
POWERFUL Operation
POWERFUL operation quickly maximizes the cooling
(heating) effect in any operation mode. You can get the
maximum capacity .
R
„ To start POWERFUL
operation
1. Press “POWERFUL button”.
• POWERFUL operation ends in 20minutes.
Then the system automatically operates
again with the previous settings which were
used before POWERFUL operation.
• “
” is displayed on the LCD.
• When using POWERFUL operation, there
are some functions which are not available.
„ To cancel POWERFUL
operation
2. Press “POWERFUL button” again.
• “
” disappears from the LCD.
ECONO
POWERFUL
ON/OFF
TEMP
1, 2
MODE
QUIET
FAN
COMFORT
SWING
SENSOR
ON
CANCEL
OFF
TIMER
NOTE
„ Notes on POWERFUL operation
• POWERFUL Operation cannot be used together with ECONO, QUIET, or COMFORT
Operation. Priority is given to the function of whichever button is pressed last.
• POWERFUL Operation can only be set when the unit is running. Pressing the operation
stop button causes the settings to be canceled, and the “ ” disappears from the LCD.
• POWERFUL operation will not increase the capacity of the air conditioner if the air
conditioner is already in operation with its maximum capacity demonstrated.
• In COOL and HEAT mode
To maximize the cooling (heating) effect, the capacity of outdoor unit must be increased
and the airflow rate be fixed to the maximum setting.
The temperature and airflow settings are not variable.
• In DRY mode
The temperature setting is lowered by 2.5°C and the airflow rate is slightly increased.
• In FAN mode
The airflow rate is fixed to the maximum setting.
• When using priority-room setting
See “Note for multi system”. (page 22.)
17
01_EN_3P207037-2D.fm Page 18 Friday, March 13, 2009 9:39 AM
OUTDOOR UNIT QUIET Operation
OUTDOOR UNIT QUIET operation lowers the noise
level of the outdoor unit by changing the frequency and
fan speed on the outdoor unit. This function is
convenient during night.
R
„ To start OUTDOOR UNIT
QUIET operation
1. Press “QUIET button”.
• “
” is displayed on the LCD.
„ To cancel OUTDOOR UNIT
QUIET operation
2. Press “QUIET button” again.
• “
ECONO
POWERFUL
MODE
QUIET
” disappears from the LCD.
ON/OFF
TEMP
FAN
COMFORT
SWING
SENSOR
ON
1, 2
CANCEL
OFF
TIMER
NOTE
„ Note on OUTDOOR UNIT QUIET operation
• If using a multi system, this function will work only when the OUTDOOR UNIT QUIET
operation is set on all operated indoor units.
However, if using priority-room setting, see “Note for multi system”. (page 22.)
• This function is available in COOL, HEAT, and AUTO modes.
(This is not available in FAN and DRY mode.)
• POWERFUL operation and OUTDOOR UNIT QUIET operation cannot be used at the
same time.
Priority is given to the function of whichever button is pressed last.
• OUTDOOR UNIT QUIET operation will drop neither the frequency nor fan speed if the
frequency and fan speed have been already dropped low enough.
18
01_EN_3P207037-2D.fm Page 19 Friday, March 13, 2009 9:39 AM
ECONO Operation
ECONO operation is a function which enables efficient
operation by limiting the maximum power consumption
value.
R
„ To start ECONO operation
1. Press “ECONO button” .
•“
” is displayed on the LCD.
„ To cancel ECONO
operation
1, 2
ECONO
POWERFUL
ON/OFF
TEMP
2. Press “ECONO button” again.
•“
” disappears from the LCD.
MODE
Running current and
power consumption
QUIET
Normal
operation
Maximum during
normal operation
Maximum during
ECONO Mode
FAN
COMFORT
SWING
SENSOR
ON
CANCEL
OFF
TIMER
ECONO
Mode
Time
From start up until set
temperature is reached
• This diagram is a representation for illustrative purposes only.
* The maximum running current and power consumption of the air conditioner in ECONO
mode vary with the connecting outdoor unit.
NOTE
• ECONO Operation can only be set when the unit is running. Pressing the OFF button
causes the setting to be canceled, and the “ ” disappears from the LCD.
• ECONO operation is a function which enables efficient operation by limiting the power
consumption of the outdoor unit (operating frequency).
• ECONO operation functions in AUTO, COOL, DRY and HEAT modes.
• POWERFUL and ECONO operation cannot be used at the same time.
Priority is given to the function of whichever button is pressed last.
• Power consumption may not drop even if ECONO operation is used of the level of power
consumption is already low.
19
01_EN_3P207037-2D.fm Page 20 Friday, March 13, 2009 9:39 AM
TIMER Operation
Timer functions are useful for automatically switching the
air conditioner on or off at night or in the morning. You
can also use OFF TIMER and ON TIMER in combination.
R
„ To use OFF TIMER
operation
• Check that the clock is correct.
If not, set the clock to the present time.
(page 9.)
1. Press “OFF TIMER button”.
is displayed.
ECONO
POWERFUL
ON/OFF
TEMP
blinks.
2. Press “TIMER Setting button”
until the time setting reaches the
point you like.
• Every pressing of either button increases or
decreases the time setting by 10 minutes.
Holding down either button changes the setting rapidly.
MODE
QUIET
FAN
COMFORT
SWING
SENSOR
ON
CANCEL
2
4
OFF
TIMER
1, 3
3. Press “OFF TIMER button” again.
• The TIMER lamp lights up.
„ To cancel the OFF TIMER operation
4. Press “CANCEL button”.
• The TIMER lamp goes off.
NOTE
• When TIMER is set, the present time is not displayed.
• Once you set ON, OFF TIMER, the time setting is kept in the memory. (The memory is
canceled when remote controller batteries are replaced.)
• When operating the unit via the ON/OFF Timer, the actual length of operation may vary from
the time entered by the user.
„ NIGHT SET MODE
When the OFF TIMER is set, the air conditioner automatically adjusts the temperature
setting (0.5°C up in COOL, 2.0°C down in HEAT) to prevent excessive cooling (heating) for
your pleasant sleep.
20
01_EN_3P207037-2D.fm Page 21 Friday, March 13, 2009 9:39 AM
„ To use ON TIMER operation
• Check that the clock is correct. If not, set the
clock to the present time.
(page 9.)
R
1. Press “ON TIMER button”.
is displayed.
blinks.
2. Press “TIMER Setting button”
until the time setting reaches the
point you like.
• Every pressing of either button increases or
decreases the time setting by 10 minutes.
Holding down either button changes the
setting rapidly.
3. Press “ON TIMER button” again.
ECONO
POWERFUL
MODE
QUIET
• The TIMER lamp lights up.
ON/OFF
TEMP
FAN
COMFORT
SWING
SENSOR
ON
1, 3
CANCEL
4
OFF
TIMER
2
„ To cancel ON TIMER
operation
4. Press “CANCEL button”.
• The TIMER lamp goes off.
„ To combine ON TIMER and OFF TIMER
• A sample setting for combining the two timers is shown below.
Display
(Example)
Present time: 11:00 p.m.
(The unit operating)
OFF TIMER at 0:00 a.m.
ON TIMER at 7:00 a.m.
Combined
ATTENTION
„ In the following cases, set the timer again.
• After a breaker has turned OFF.
• After a power failure.
• After replacing batteries in the remote controller.
21
01_EN_3P207037-2D.fm Page 22 Friday, March 13, 2009 9:39 AM
Note for Multi System
〈〈 What is a “Multi System”? 〉〉
This system has one outdoor unit connected to multiple indoor units.
„ Selecting the Operation Mode
1. With the Priority Room Setting
present but inactive or not present.
A
room
Outdoor
unit
B
room
Living
room
C
room
When more than one indoor unit is operating, priority is
given to the first unit that was turned on.
In this case, set the units that are turned on later to the
same operation mode (*1) as the first unit.
Otherwise, they will enter the Standby Mode, and the operation lamp will flash; this does not indicate malfunction.
(*1)
• COOL, DRY and FAN mode may be used at the same time.
• AUTO mode automatically selects COOL mode or HEAT mode based on the room temperature.
Therefore, AUTO mode is available when selecting the same operation mode as that of the room
with the first unit to be turned on.
〈CAUTION〉
Normally, the operation mode in the room where the unit is first run is given priority, but the following situations are
exceptions, so please keep this in mind.
If the operation mode of the first room is FAN Mode, then using Heating Mode in any room after this will give priority to
heating. In this situation, the air conditioner running in FAN Mode will go on standby, and the operation lamp will flash.
2. With the Priority Room Setting active.
See “Priority Room Setting” on the next page.
„ NIGHT QUIET Mode (Available only for cooling operation)
NIGHT QUIET Mode requires initial programming during installation. Please consult your retailer or dealer for assistance.
NIGHT QUIET Mode reduces the operation noise of the outdoor unit during the night time hours to prevent
annoyance to neighbors.
• The NIGHT QUIET Mode is activated when the temperature drops 5°C or more below the highest temperature
recorded that day. Therefore, when the temperature difference is less than 5°C, this function will not be activated.
• NIGHT QUIET Mode reduces slightly the cooling efficiency of the unit.
„ OUTDOOR UNIT QUIET Operation (page 18.)
1. With the Priority Room Setting present but inactive or not present.
When using the OUTDOOR UNIT QUIET operation feature with the Multi system, set all indoor units to
OUTDOOR UNIT QUIET operation using their remote controllers.
When clearing OUTDOOR UNIT QUIET operation, clear one of the operating indoor units using their remote controller.
However OUTDOOR UNIT QUIET operation display remains on the remote controller for other rooms.
We recommend you release all rooms using their remote controllers.
2. With the Priority Room Setting active.
See “Priority Room Setting” on the next page.
„ Cooling / Heating Mode Lock (Available only for heat pump models)
The Cooling / Heating Mode Lock requires initial programming during installation.Please consult your retailer or dealer
for assistance. The Cooling / Heating Mode Lock sets the unit forcibly to either Cooling or Heating Mode. This function
is convenient when you wish to set all indoor units connected to the Multi system to the same operation mode.
22
01_EN_3P207037-2D.fm Page 23 Friday, March 13, 2009 9:39 AM
„ Priority Room Setting
The Priority Room Setting requires initial programming during installation. Please consult your
retailer or dealer for assistance.
The room designated as the Priority Room takes priority in the following situations;
1. Operation Mode Priority.
As the operation mode of the Priority Room takes precedence, the user can select a different
operation mode from other rooms.
〈Example〉
* Room A is the Priority Room in the examples.
When COOL mode is selected in Room A while operating the following modes in Room B,C and D:
Operation mode in Room B, C and D
COOL or DRY or FAN
Status of Room B, C and D when the unit in Room A is in COOL mode
Current operation mode maintained
HEAT
The unit enters Standby Mode. Operation resumes when the
Room A unit stops operating.
AUTO
If the unit is set to COOL mode, operation continues. If set to
HEAT mode, it enters Standby Mode. Operation resumes when
the Room A unit stops operating.
2. Priority when POWERFUL operation is used.
〈Example〉
* Room A is the Priority Room in the examples.
The indoor units in Rooms A,B,C and D are all operating. If the unit in Room A enters POWERFUL
operation, operation capacity will be concentrated in Room A. In such a case, the cooling (heating)
efficiency of the units in Rooms B,C and D may be slightly reduced.
3. Priority when using OUTDOOR UNIT QUIET operation.
〈Example〉
* Room A is the Priority Room in the examples.
Just by setting the unit in Room A to QUIET operation, the air conditioner starts OUTDOOR UNIT
QUIET operation.
You don’t have to set all the operated indoor units to QUIET operation.
23
01_EN_3P207037-2D.fm Page 24 Friday, March 13, 2009 9:39 AM
Care and Cleaning
CARE
CAUTION
Before cleaning, be sure to stop the operation and
turn the breaker OFF.
Units
„ Indoor unit, Outdoor unit and Remote controller
1. Wipe them with dry soft cloth.
„ Front panel
1. Open the front panel.
• Hold the panel by the tabs on the two sides and lift
it unitl it stops with a click.
2. Remove the front panel.
• Lift the front panel up, slide it slightly to the right,
and remove it from the horizontal axle.
3. Clean the front panel.
• Wipe it with a soft cloth soaked in water.
• Only neutral detergent may be used.
• In case of washing the panel with water, dry it with
cloth, dry it up in the shade after washing.
4. Attach the front panel.
• Set the 2 keys of the front panel into the slots and
push them in all the way.
• Close the front panel slowly and push the panel at
the 3 points.
( 1 on each side and 1 in the middle.)
Fit the key
into the slot.
CAUTION
•
•
•
•
Don’t touch the metal parts of the indoor unit. If you touch those parts, this may cause an injury.
When removing or attaching the front panel, use a robust and stable stool and watch your steps carefully.
When removing or attaching the front panel, support the panel securely with hand to prevent it from falling.
For cleaning, do not use hot water above 40°C, benzine, gasoline, thinner, nor other volatile oils, polishing compound, scrubbing brushes, nor other hand stuff.
• After cleaning, make sure that the front panel is securely fixed.
24
01_EN_3P207037-2D.fm Page 25 Friday, March 13, 2009 9:39 AM
Filters
1. Open the front panel. (page 24.)
2. Pull out the air filters.
• Push a little upwards the tab at the center of each
air filter, then pull it down.
3. Take off the Titanium Apatite
Photocatalytic Air-Purifying Filter.
• Hold the recessed parts of the frame and unhook
the four claws.
Titanium Apatite
Photocatalytic
Air-Purifying Filter
4. Clean or replace each filter.
See figure.
Filter frame
Tab
5. Set the air filter and Titanium Apatite
Photocatalytic Air-Purifying Filter as
they were and close the front panel.
Air filter
Push
• Insert claws of the filters into slots of the front panel.
Close the front panel slowly and push the panel at
the 3 points. (1 on each side and 1 in the middle.)
„ Air Filter
1. Wash the air filters with water or clean them with
vacuum cleaner.
• If the dust does not come off easily, wash them with neutral detergent
thinned with lukewarm water, then dry them up in the shade.
• It is recommended to clean the air filters every two weeks.
„ Titanium Apatite Photocatalytic
Air-Purifying Filter
The Titanium Apatite Photocatalytic Air-Purifying Filter can be renewed
by washing it with water once every 6 months. We recommend replacing it once every 3 years.
[ Maintenance ]
1. Vacuum dusts, and soak in warm water or water for about 10 to 15
minutes if dirt is heavy.
2. Do not remove filter from frame when washing with water.
3. After washing, shake off remaining water and dry in the shade.
4. Since the material is made out of polyester, do not wring out the filter when removing water from it.
[ Replacement]
1. Remove the tabs on the filter frame and replace with a new filter.
• Dispose of the old filter as non-flammable waste.
25
01_EN_3P207037-2D.fm Page 26 Friday, March 13, 2009 9:39 AM
NOTE
• Operation with dirty filters:
(1) cannot deodorize the air.
(2) cannot clean the air.
(3) results in poor heating or cooling. (4) may cause odour.
• To order Titanium Apatite Photocatalytic Air-Purifying Filter contact to the service shop
there you bought the air conditioner.
• Dispose of the old filter as non-flammable waste.
Item
Titanium Apatite Photocatalytic Air-Purifying Filter
(without frame) 1 set
Part No.
KAF970A46
Check
Check that the base, stand and other fittings of the outdoor unit are not decayed or corroded.
Check that nothing blocks the air inlets and the outlets of the indoor unit and the outdoor unit.
Check that the drain comes smoothly out of the drain hose during COOL or DRY operation.
• If no drain water is seen, water may be leaking from the indoor unit. Stop operation and consult the service shop if this is the case.
„ Before a long idle period
1. Operate the “FAN only” for several hours on a fine day to dry out the
inside.
• Press “MODE selector button” and select “FAN” operation.
• Press “ON/OFF button” and start operation.
2. After operation stops, turn off the breaker for the room air conditioner.
3. Clean the air filters and set them again.
4. Take out batteries from the remote controller.
NOTE
• When a multi outdoor unit is connected, make sure the heating operation is not used at
the other room befure you use the fan operation. (page 22.)
26
01_EN_3P207037-2D.fm Page 27 Friday, March 13, 2009 9:39 AM
Trouble Shooting
TROUBLE SHOOTING
These cases are not troubles.
The following cases are not air conditioner troubles but have some reasons. You may just continue using it.
Case
Explanation
Operation does not start soon.
• When ON/OFF button was
pressed soon after
operation was stopped.
• When the mode was
reselected.
• This is to protect the air conditioner.
You should wait for about 3 minutes.
Hot air does not flow out soon
after the start of heating
operation.
• The air conditioner is warming up. You should wait for 1 to 4 minutes.
(The system is designed to start discharging air only after it
has reached a certain temperature.)
The heating operation stops
suddenly and a flowing sound
is heard.
• The system is taking away the frost on the outdoor unit.
You should wait for about 3 to 8 minutes.
The outdoor unit emits water or
steam.
„ In HEAT mode
• The frost on the outdoor unit melts into water or steam
when the air conditioner is in defrost operation.
„ In COOL or DRY mode
• Moisture in the air condenses into water on the cool
surface of outdoor unit piping and drips.
Mist comes out of the indoor
unit.
„ This happens when the air in the room is cooled into mist by
the cold airflow during cooling operation.
The indoor unit gives out odour. „ This happens when smells of the room, furniture, or cigarettes
are absorbed into the unit and discharged with the airflow.
(If this happens, we recommend you to have the indoor unit
washed by a technician. Consult the service shop where you
bought the air conditioner.)
The outdoor fan rotates while
the air conditioner is not in
operation.
„ After operation is stopped:
• The outdoor fan continues rotating for another 60
seconds for system protection.
„ While the air conditioner is not in operation:
• When the outdoor temperature is very high, the outdoor
fan starts rotating for system protection.
The operation stopped
suddenly.
(OPERATION lamp is on.)
„ For system protection, the air conditioner may stop
operating on a sudden large voltage fluctuation.
It automatically resumes operation in about 3 minutes.
No remote controller signals are • The batteries are dying and the remote controller is malfuncdisplayed.
tioning. Replace all the batteries with new size AAA alkaline
The remote controller sensitivity is low.
batteries. For details, refer to “To set the batteries” of this
manual. (page 7.)
The display is low in contrast or
* If the reset button is provided, press the reset button after the
blacked out.
batteries are replaced.
The display runs out of control.
27
01_EN_3P207037-2D.fm Page 28 Friday, March 13, 2009 9:39 AM
Check again.
Please check again before calling a repair person.
Case
The air conditioner does not
operate.
(OPERATION lamp is off.)
Check
• Hasn’t a breaker turned OFF or a fuse blown?
• Isn’t it a power failure?
• Are batteries set in the remote controller?
• Is the timer setting correct?
Cooling (Heating) effect is poor. • Are the air filters clean?
• Is there anything to block the air inlet or the outlet of the
indoor and the outdoor units?
• Is the temperature setting appropriate?
• Are the windows and doors closed?
• Are the airflow rate and the air direction set appropriately?
• Is the unit set to the INTELLIGENT EYE mode?
(page 15.)
Operation stops suddenly.
(OPERATION lamp flashes.)
• Are the air filters clean?
An abnormal functioning
happens during operation.
• The air conditioner may malfunction with lightning or radio
waves. Turn the breaker OFF, turn it ON again and try
operating the air conditioner with the remote controller.
28
• Is there anything to block the air inlet or the outlet of the
indoor and the outdoor units?
Clean the air filters or take all obstacles away and turn the
breaker OFF. Then turn it ON again and try operating the air
conditioner with the remote controller. If the lamp still flashes,
call the service shop where you bought the air conditioner.
• Are operation modes all the same for indoor units
connected to outdoor units in the multi system?
If not, set all indoor units to the same operation mode and
confirm that the lamps blink.
Moreover, when the operation mode is in “AUTO”, set all
indoor unit operation modes to “COOL” or “HEAT” for a
moment and check again that the lamps are normal.
If the lamps stop blinking after the above steps, there is no
malfunction.
(page 22.)
01_EN_3P207037-2D.fm Page 29 Friday, March 13, 2009 9:39 AM
Call the service shop immediately.
WARNING
■ When an abnormality (such as a burning smell) occurs, stop operation and turn the breaker OFF.
Continued operation in an abnormal condition may result in troubles, electric shocks or fire.
Consult the service shop where you bought the air conditioner.
■ Do not attempt to repair or modify the air conditioner by yourself.
Incorrect work may result in electric shocks or fire.
Consult the service shop where you bought the air conditioner.
If one of the following symptoms takes place, call the service shop immediately.
n
n
n
n
n
n
The power cord is abnormally hot or damaged.
An abnormal sound is heard during operation.
The safety breaker, a fuse, or the earth leakage breaker
cuts off the operation frequently.
A switch or a button often fails to work properly.
There is a burning smell.
Water leaks from the indoor unit.
Turn the breaker
OFF and call the
service shop.
■ After a power failure
■ Lightning
The air conditioner automatically resumes operation
If lightning may strike the neighbouring area, stop operin about 3 minutes. You should just wait for a while.
ation and turn the breaker OFF for system protection.
Disposal requirements
Your product and the batteries supplied with the controller are marked with this symbol. This symbol means
that electrical and electronic products and batteries shall not be mixed with unsorted household waste.
For batteries, a chemical symbol can be printed beneath the symbol. This chemical symbol means
that the battery contains a heavy metal above a certain concentration. Possible chemical symbols are:
„ Pb: lead (>0.004%)
Do not try to dismantle the system yourself: the dismantling of the product, treatment of the refrigerant, of oil and
of other parts must be done by a qualified installer in accordance with relevant local and national legislation.
Units and waste batteries must be treated at a specialized treatment facility for re-use, recycling and recovery.
By ensuring correct disposal, you will help to prevent potential negative consequences for the environment and human health.
Please contact the installer or local authority for more information.
We recommend periodical maintenance.
In certain operating conditions, the inside of the air conditioner may get foul after several seasons of use, resulting in poor performance. It is recommended to have periodical maintenance by a specialist aside from regular
cleaning by the user. For specialist maintenance, contact the service shop where you bought the air conditioner.
The maintenance cost must be born by the user.
Important information regarding the refrigerant used.
This product contains fluorinated greenhouse gases covered by the Kyoto Protocol.
Refrigerant type:R410A
GWP(1) value:1975
(1) GWP = global warming potential
Periodical inspections for refrigerant leaks may be required depending on European or local legislation.
Please contact your local dealer for more information.
29
01_EN_3P207037-2D.fm Page 30 Friday, March 13, 2009 9:39 AM
Fault diagnosis.
FAULT DIAGNOSIS BY REMOTE CONTROLLER
In the ARC433 series, the temperature display sections on the main unit indicate corresponding codes.
1. When the TIMER CANCEL button is held down for 5 seconds, a “ ” indication flashes on the
temperature display section.
R
ECONO
POWERFUL
MODE
QUIET
ON/OFF
TEMP
FAN
COMFORT
SWING
SENSOR
ON
CANCEL
TIMER CANCEL button
It cancels the timer setting.
OFF
TIMER
2. Press the TIMER CANCEL button repeatedly until a continuous beep is produced.
• The code indication changes as shown below, and notifies with a long beep.
SYSTEM
INDOOR UNIT
OUTDOOR
UNIT
CODE
00
UA
U0
U2
U4
A1
A5
A6
C4
C9
EA
E1
E5
E6
E7
E8
F3
F6
H0
H6
H8
H9
J3
J6
L3
L4
L5
P4
MEANING
NORMAL
INDOOR-OUTDOOR UNIT COMBINATION FAULT
REFRIGERANT SHORTAGE
DROP VOLTAGE OR MAIN CIRCUIT OVERVOLTAGE
FAILURE OF TRANSMISSION (BETWEEN INDOOR UNIT AND OUTDOOR UNIT)
INDOOR PCB DEFECTIVENESS
HIGH PRESSURE CONTROL OR FREEZE-UP PROTECTOR
FAN MOTOR FAULT
FAULTY HEAT EXCHANGER TEMPERATURE SENSOR
FAULTY SUCTION AIR TEMPERATURE SENSOR
COOLING-HEATING SWITCHING ERROR
CIRCUIT BOARD FAULT
OL STARTED
FAULTY COMPRESSOR START UP
DC FAN MOTOR FAULT
OVERCURRENT INPUT
HIGH TEMPERATURE DISCHARGE PIPE CONTROL
HIGH PRESSURE CONTROL (IN COOLING)
SENSOR FAULT
OPERATION HALT DUE TO FAULTY POSITION DETECTION SENSOR
CT ABNORMALITY
FAULTY SUCTION AIR TEMPERATURE SENSOR
FAULTY DISCHARGE PIPE TEMPERATURE SENSOR
FAULTY HEAT EXCHANGER TEMPERATURE SENSOR
ELECTRICAL PARTS HEAT FAULT
HIGH TEMPERATURE AT INVERTER CIRCUIT HEATSINK
OUTPUT OVERCURRENT
FAULTY INVERTER CIRCUIT HEATSINK TEMPERATURE SENSOR
NOTE
1. A short beep and two consecutive beeps indicate non-corresponding codes.
2. To cancel the code display, hold the TIMER CANCEL button down for 5 seconds. The code display
also cancel itself if the button is not pressed for 1 minute.
30
01_EN_3P207037-2D.fm Page 31 Friday, March 13, 2009 9:39 AM
LED ON OUTDOOR UNIT PCB
2AMX, 3AMX series
GREEN
RED
MICROCOMPUTER
NORMAL
MALFUNCTION
DETECTION
LED-A
LED1 LED2 LED3 LED4
DIAGNOSIS
NORMAL
CHECK INDOOR UNIT
HIGH PRESSURE PROTECTOR WORKED OR FREEZE-UP IN OPERATING UNIT OR STAND-BY UNIT
∗ OVERLOAD RELAY WORKED OR HIGH DISCHARGE PIPE TEMPERATURE
FAULTY COMPRESSOR START
INPUT OVERCURRENT
∗ THERMISTOR OR CT ABNORMALITY
HIGH TEMPERATURE SWITCHBOX
HIGH TEMPERATURE AT INVERTER CIRCUIT HEATSINK
∗ OUTPUT OVERCURRENT
∗ REFRIGERANT SHORTAGE
LOW VOLTAGE TO MAIN CIRCUIT OR MOMENTARY VOLTAGE LOSS
REVERSING SOLENOID VALVE SWITCHING FAILURE
FAN MOTOR FAULT
[NOTE 1]
POWER SUPPLY FAULT OR [NOTE 2]
GREEN
RED
NORMALLY
FLASHING
NORMALLY OFF
ON
FLASHING
OFF
IRRELEVANT
LED ON OUTDOOR UNIT PCB
2AMX, 2AMXS series
GREEN
MICROCOMPUTER
NORMAL
DIAGNOSIS
LED-A
NORMAL
CHECK INDOOR UNIT
[NOTE 1]
POWER SUPPLY FAULT OR [NOTE 2]
GREEN
NORMALLY
FLASHING
ON
FLASHING
OFF
NOTE
1. Turn the power off and then on again. If the LED display recurs,the outdoor unit PCB is faulty.
2. Diagnosis marked
∗ Do not apply to some cases. For details, refer to the service guide.
31
01_EN_3P207037-2D.fm Page 32 Friday, March 13, 2009 9:39 AM
MEMO
32
00_CV_3P207037-2D.fm Page 2 Wednesday, March 11, 2009 9:15 AM
Two-dimensional bar code is a code
for manufacturing.
3P207037-2D M07B015B (0903)
HT
Download PDF