Carrier Access | Network Device Axxius 800 | User manual | Carrier Access Network Device Axxius 800 User manual

Axxius 800
USER MANUAL
Part Number: 770-0104 AG
Product Release: 2.2
May 2004
Copyright 2004 Carrier Access Corporation. All rights reserved.
The information presented in this manual is subject to change without notice and does not represent a
commitment on the part of Carrier Access Corporation. The hardware and software described herein are
furnished under a license or non-disclosure agreement. The hardware, software, and manual may be used or
copied only in accordance with the terms of this agreement. It is against the law to reproduce, transmit,
transcribe, store in a retrieval system, or translate into any medium - electronic, mechanical, magnetic,
optical, chemical, manual, or otherwise - any part of this manual or software supplied with the Axxius 800
for any purpose other than the purchaser’s personal use without the express written permission of Carrier
Access Corporation.
The Carrier Access Logo, Access Navigator, Axxius, solve for x, and NetworkValet are registered trademarks
of Carrier Access Corporation. All other brand or product names are trademarks or registration trademarks of
their respective companies or organizations.
Contact Information:
Carrier Access Corporation
5395 Pearl Parkway
Boulder, CO 80301-2490
Corporate Phone: (800) 495-5455
Fax: (303) 443-5908
www.carrieraccess.com
Customer Support Direct: (800) 786-9929
E-mail: tech-support@carrieraccess.com
Supporting Software Version:
Axxius 800 Controller Release 2.2
Terminal Server Router Release 1.3
PREFACE
Preface
Compliance
Safety
The Axxius 800 is certified by Underwriters Laboratories and is in compliance with UL60950, 3rd Edition;
Safety of Information Technology Equipment and CSA/C22.2 No 60950.
FCC Requirements, Part 15
This equipment has been tested and found to comply with the limits for a Class A digital device pursuant
to Part 15 of the Federal Communications Rules. These limits are designed to provide reasonable
protection against harmful interference when equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instruction manual may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at the user’s own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Requirements, Part 68
This equipment complies with Part 68 of the Federal Commission Rules. On the outside surface of this
equipment is a label that contains, among other information, the FCC registration number, Facility
Interface Code (FIC) and Service Order Code (SOC). This information must be provided to the telephone
company.
FCC Registration Number: US:2Z6MF03B800
Ringer Equivalence: 0.3B REN
Service Center in the USA: Carrier Access Corporation, 5395 Pearl Parkway, Boulder, CO 80301-2490
Preface
Compliance
The Facility Interface Code (FIC) associated with each private line application represents the type of
service that will be provided by the telephone company. The following are currently registered:
Port:
FIC:
SOC:
Jack:
HD Quad T1 1.544 Mbps
04DU9-BN
6.0F
RJ48C
HD Quad T1 1.544 Mbps
04DU9-DN
6.0F
RJ48C
HD Quad T1 1.544 Mbps
04DU9-1KN
6.0F
RJ48C
HD Quad T1 1.544 Mbps
04DU9-1SN
6.0F
RJ48C
HD Quad DS1 ADPCM 1.544 Mbps
04DU9-BN
6.0F
RJ48C
HD Quad DS1 ADPCM 1.544 Mbps
04DU9-DN
6.0F
RJ48C
HD Quad DS1 ADPCM 1.544 Mbps
04DU9-1KN
6.0F
RJ48C
HD Quad DS1 ADPCM 1.544 Mbps
04DU9-1SN
6.0F
RJ48C
Front Interface T1 1.544 Mbps
04DU9-BN
6.0F
RJ48C
Front Interface T1 1.544 Mbps
04DU9-DN
6.0F
RJ48C
Front Interface T1 1.544 Mbps
04DU9-1KN
6.0F
RJ48C
Front Interface T1 1.544 Mbps
04DU9-1SN
6.0F
RJ48C
V.34 Modem Interface
02LS2
9.0F
RJ11C
An FCC-compliant telephone and modular plug is provided with this equipment. This equipment is
designed to be connected to the telephone network or premises wiring using a compatible modular jack
which is Part 68 Compliant. See installation instructions for details.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance
that temporary discontinuance of service may be required. But if advance notice is not practical, the
telephone company will notify the customer as soon as possible. Also, you will be advised of your right to
file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment operations, or procedures that could
affect the operation of the equipment. If this happens, the telephone company will provide advance notice
so that you may make necessary modifications in order to maintain uninterrupted service.
If trouble is experienced with the Axxius 800, please contact the Carrier Access Customer Support at (800)
786-9929 or (303) 442-5455. If the equipment is causing harm to the network, the telephone company may
request you to remove the equipment from the network until the problem is resolved.
No repairs are to be made by you. Repairs are to be made only by Carrier Access or its licensees.
Unauthorized repairs void registration and warranty.
This equipment cannot be used on public coin service provided by the telephone company. Connection to
Party Line Service is subject to state tariffs. (Contact your state public utility commission, public service
commission or corporation commission for information.3
iv
Axxius 800 - Release 2.2
Preface
Compliance
Industry Canada CS-03
Registration Number: IC: 2638A-800
’’NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical
Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration
number signifies that registration was performed based on a Declaration of Conformity indicating that
Industry Canada technical specifications were met. It does not imply that Industry Canada approved the
equipment.”
''NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.3. The REN assigned
to each terminal equipment provides an indication of the maximum number of terminals allowed to be
connected to a telephone interface. The termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices
does not exceed five.''
Industry Canada ICES-003
English
This class A digital apparatus complies with Canadian ICES-003.
French
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
NOTE: See Compliant Installation on page 3-2 for installation instructions to
meet FCC Part 15 requirements.
Axxius 800 - Release 2.2
v
Preface
Safety Information
Safety Information
CAUTION! ALWAYS USE CAUTION WHEN INSTALLING TELEPHONE LINES.
READ THE CAUTIONS BELOW FOR DETAILS ON SAFETY GUIDELINES TO PREVENT
INJURY.
l Never touch uninsulated telephone wires and terminals unless the
telephone line has been disconnected at the Network Interface (NI) as
voltage potentials as high as 300 VAC may be present across the transmit
and receive pairs.
l Only use No. 26 AWG or larger telecommunication line cord, to reduce
the risk of fire.
l Never install telephone wiring during a lightning storm.
l Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
l Refer to the installation section of this manual for a safe and proper
installation procedure. All wiring external to this equipment should follow
the current provision of the National Electrical Code.
vi
Axxius 800 - Release 2.2
Preface
Notices
Notices
This manual contains important information and warnings that must be followed to
ensure safe operation of the equipment.
DANGER! A DANGER NOTICE INDICATES THE PRESENCE OF A HAZARD THAT
CAN OR WILL CAUSE DEATH OR SEVERE PERSONAL INJURY IF THE HAZARD IS
NOT AVOIDED.
CAUTION! A CAUTION NOTICE INDICATES THE POSSIBILITY OF
INTERRUPTING NETWORK SERVICE IF THE HAZARD IS NOT AVOIDED.
WARNING! A WARNING NOTICE INDICATES THE POSSIBILITY OF EQUIPMENT
DAMAGE IF THE HAZARD IS NOT AVOIDED.
NOTE: A Note indicates information to help you understand how to
perform a procedure or how the system works. Notes should be read before
performing the required action.
Axxius 800 - Release 2.2
vii
Preface
Electrostatic Discharge (ESD) Precautions
Electrostatic Discharge (ESD) Precautions
ESD can damage processors, circuit cards, and other electronic components. Always
observe the following precautions before installing a system component.
1. Do not remove a component from its protective packaging until ready to install
it.
2. Wear a wrist grounding strap and attach it to a metal part of the system unit
before handling components. If a wrist strap is not available, maintain contact
with the system unit throughout any procedure requiring ESD protection.
WARNING! INTEGRATED CIRCUITS (ICS) ARE EXTREMELY SUSCEPTIBLE TO
ELECTROSTATIC DISCHARGE. UNLESS YOU ARE A QUALIFIED SERVICE
TECHNICIAN WHO USES TOOLS AND TECHNIQUES THAT CONFORM TO ACCEPTED
INDUSTRY PRACTICES, DO NOT HANDLE ICS.
The ESD warning label appears on packages and storage bags
that contain static-sensitive products and components.
viii
Axxius 800 - Release 2.2
Preface
Warranty
Warranty
Carrier Access Corporation conditionally warrants to BUYER that PRODUCTS are free from substantial
defect in material and workmanship under normal use given proper installation and maintenance for the
period of five years from the date of shipment by Carrier Access Corporation.
BUYER will promptly notify Carrier Access Corporation of any defect in the PRODUCT. Carrier Access
Corporation or its agent will have the right to inspect the PRODUCT or workmanship on BUYER’S or
BUYER’S customer premises. Carrier Access Corporation has the option to: (a) repair, replace or service
at its factory or on the premises the PRODUCT or workmanship found to be defective; or (b) credit
BUYER for the PRODUCT in accordance with Carrier Access Corporation’s depreciation policy.
Refurbished material may be used to repair or replace the PRODUCT. PRODUCTS returned to Carrier
Access Corporation for repair, replacement, or credit will be shipped prepaid to BUYER.
Limitations of Warranty & Limitation of Remedies
Correction of defects by repair, replacement, service or credit will be at Carrier Access Corporation’s
option and constitute fulfillment of all obligations to buyer for breach of warranty.
Carrier Access Corporation assumes no warranty liability with respect to defects in the PRODUCT caused
by: (a) modification, repair, installation, operation or maintenance of the PRODUCT by anyone other than
Carrier Access Corporation or its agent, except as described in Carrier Access Corporation’s
documentation; or (b) the negligent or other improper use of the PRODUCT; or (c) handling or
transportation after title of the PRODUCT passes to BUYER.
Other manufacturer’s equipment purchased by Carrier Access Corporation and resold to BUYER will be
limited to that manufacture’s warranty. Carrier Access Corporation assumes no warranty liability for other
manufacturer’s equipment furnished by BUYER.
Buyer understands and agrees as follows: the warranties in this agreement replace all other warranties,
expressed or implied, and all other obligations or liabilities of Carrier Access Corporation, including any
warranties of merchantability and fitness for a particular purpose. All other warranties are disclaimed and
excluded by Carrier Access Corporation.
The remedies contained in this agreement will be the sole and exclusive remedies whether in contract, tort
or otherwise, and Carrier Access Corporation will not be liable for injuries or damages to persons or
property resulting from any case whatsoever, with the exception of injuries or damages caused by the gross
negligence of Carrier Access Corporation. These limitations apply to all services, software, and products
during and after the warranty period. In no event will Carrier Access Corporation be liable for any special,
incidental, or consequential damages or commercial losses even if Carrier Access Corporation has been
advised thereof.
No agent, distributor, or representative is authorized to make any warranties on behalf of Carrier Access
Corporation or to assume for Carrier Access Corporation any other liability in connection with any of
Carrier Access Corporation’s PRODUCTS, Software, or Services.
Axxius 800 - Release 2.2
ix
Preface
Warranty
Warranty Product Returns
Before returning any equipment to Carrier Access Corporation, first contact the distributor or dealer from
which you purchased the product.
A Return Material Authorization (RMA) number is required for all equipment returned to Carrier Access
Corporation. Call Carrier Access Corporation Customer Support at (800) 786-9929 or (303) 442-5455 for
RMA number, repair/warranty information and shipping instructions. Be prepared to provide the
following information:
x
l
Carrier Access Corporation serial number(s) from the system chassis or circuit card(s)
l
Name of distributor or dealer from which you purchased the product
l
Description of defect
Axxius 800 - Release 2.2
TABLE OF CONTENTS
Table of Contents
Preface
Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
FCC Requirements, Part 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
FCC Requirements, Part 68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Industry Canada CS-03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Industry Canada ICES-003 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Electrostatic Discharge (ESD) Precautions . . . . . . . . . . . . . . . . . . . . . . . viii
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Limitations of Warranty & Limitation of Remedies . . . . . . . . . . . . . . ix
Warranty Product Returns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
1
Base Platform
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controllers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dual DS3 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quad DS1 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FXO Service card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ISDN BRI Service card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OCU-DP Service card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
POTS Service card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quad DS1 ADPCM Service card . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quad DS1/E1 and T1 Service cards . . . . . . . . . . . . . . . . . . . . . . . . . . .
V.35/54 Service cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Server Router (TSR) Service card. . . . . . . . . . . . . . . . . . . . .
1-2
1-3
1-4
1-4
1-4
1-4
1-4
1-4
1-5
1-5
1-5
1-5
1-5
1-5
Table of Contents
Low Speed Protection card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
24 VDC Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
48 VDC I48 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
48 VDC NI48 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Platform Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Control Panel Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Rear Chassis Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Alarm Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Network Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Physical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Built-In Card Handles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Management Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
RS-232 Craft Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
10/100Base-T Ethernet Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Local and Remote Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Control Panel Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
SMB connector (female) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
RS-232 Craft Port (Female DB-9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
DS1 Connection Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
10/100Base-T Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Control Panel Interface Card Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Control Panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15
Alarm LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15
Ethernet LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16
ACO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17
xii
Axxius 800 - Release 2.2
Table of Contents
2
Physical Installation
Unpacking and Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assembly of Axxius 800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
2-2
2-3
2-4
2-5
Electrical Installation and Cabling
Compliant Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Ferrite Beads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Chassis Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Chassis Ground Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
External Alarm Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Visible and Audible Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
BITS Clock 1/BITS Clock 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Slot (1-8) Wire-Wrap Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Standard Telco Color Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
4
Configuration
Setting up a CLI Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Basic System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Initial Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Set Up Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Set Up IP Addresses for Telnet CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Upgrade the Axxius 800 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Set Up a DS0/Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Set Up a DS1/T1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Set Up a DS3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Establish a Static Channel Connection . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Setup of ADPCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Set Up a V.35 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Set Up a Single Channel POTS card. . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Change the IP Address of the DS0 Management Channel . . . . . . . . . 4-10
Axxius 800 - Release 2.2
xiii
Table of Contents
Quick Configuration Reload. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
Setup of DS0 Management Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Equipment Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Set IP Configuration of PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17
Configuring the Axxius Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17
Testing the DS0 Management Channel . . . . . . . . . . . . . . . . . . . . . . . . 4-28
5
CLI Commands
Command Line Interface Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
? or help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
[TAB] usage for word or command completion . . . . . . . . . . . . . . . . . . 5-2
CLI Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
aco (Alarm Cut Off) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
add . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
add (ds1) ais . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
add (router) dhcp server option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
add (router) dns proxy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
add (router) remote. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
add (router) snmp community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
add (router) snmp trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
add (router) static dns host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
add (router) uploaduser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
add (router-lan) filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
add (router-lan) secondary ip address . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
add (router-lan) static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
add (router-wan) firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23
add (router-wan) gre network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26
add (router-wan) nat bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-27
add (router-wan) static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-28
add user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-32
alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-33
clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-34
clear (ds1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-35
clear (ds3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-36
xiv
Axxius 800 - Release 2.2
Table of Contents
clear key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
clear log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
clear (ocudp) performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
clear (router) ip address table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
clear (router) mac address table . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
clear (router) performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel Associated Signaling (CAS) Conversions . . . . . . . . . . . . . .
connect (router-trunk) (t1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delete (ds1) ais . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delete (router) dhcp server option . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delete (router) dns proxy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delete (router) remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delete (router) snmp community . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delete (router) snmp trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delete (router) static dns host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delete (router) uploaduser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delete (router-lan) filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delete (router-lan) secondary ip address . . . . . . . . . . . . . . . . . . . . . . .
delete (router-lan) static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delete (router-wan) firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delete (router-wan) gre network . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delete (router-wan) nat bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delete (router-wan) static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delete user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
disconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
disconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
install (slot) router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
load tftp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
load xmodem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Axxius 800 - Release 2.2
5-37
5-37
5-37
5-38
5-38
5-39
5-40
5-40
5-41
5-42
5-43
5-44
5-44
5-45
5-45
5-46
5-46
5-47
5-48
5-49
5-50
5-53
5-54
5-54
5-55
5-58
5-58
5-58
5-59
5-59
5-59
5-60
5-60
5-61
xv
Table of Contents
log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-62
ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-63
print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-64
print config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-64
print help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-65
rename (router) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-65
reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-66
reset (controller) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-66
reset (router) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-66
reset (router) coldboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-67
restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-67
restore defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-67
rtrping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-68
set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-69
set alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-71
set autoexit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-71
set (bri) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-72
set (bri) mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-73
set (bri) pmsync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-73
set cclabel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-74
set clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-74
set clock (1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-75
set date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-75
set (ds0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-76
set (ds1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-78
set (ds1 card) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-81
set (ds3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-83
set ethernet ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-86
set external alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-86
set (fxo) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-87
set (fxsPS or fxsPSM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-88
set id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-88
set idle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-89
set ip gateway. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-89
xvi
Axxius 800 - Release 2.2
Table of Contents
set ipds0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-90
set key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-91
set login auth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-91
set login support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-92
set lsbackup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-92
set lsprotect enable/disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-93
set lsprotect manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-93
set lsprotect nonrevertive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-94
set lsprotect remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-95
set lsprotect revertive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-96
set (ocudp) baud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-97
set (ocudp) loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-98
set (ocudp) loopdetect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-99
set (ocudp) mvec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-100
set (ocudp) secondary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-100
set (ocudp) selftest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-101
set (ocudp) up/down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-101
set (router) autologout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-102
set (router) default. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-102
set (router) dhcp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-103
set (router) dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-108
set (router) enhanced security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-110
set (router) lmi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-110
set (router) lmi poll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-111
set (router) login auth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-111
set (router) login prompt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-112
set (router) ntp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-112
set (router) password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-114
set (router) port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-115
set (router) ppp auth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-125
set (router) ppp security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-127
set (router) proxy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-129
set (router) reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-131
Axxius 800 - Release 2.2
xvii
Table of Contents
set (router) rip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-131
set (router) snmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-132
set (router) stp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-134
set (router) syslog. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-137
set (router-lan) filter forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-139
set (router-lan) framing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-140
set (router-lan) gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-141
set (router-lan) ip address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-142
set (router-lan) ipx network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-143
set (router-lan) phy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-144
set (router-lan) rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-145
set (router-lan) stp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-147
set (router-lan) up/down. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-149
set (router-trunk) encapsulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-150
set (router-trunk) multilink group . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-150
set (router-trunk) speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-151
set (router-trunk) up/down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-151
set (router-wan) dlci . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-152
set (router-wan) gre . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-153
set (router-wan) ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-155
set (router-wan) ip address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-155
set (router-wan) ipx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-156
set (router-wan) nat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-157
set (router-wan) other . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-159
set (router-wan) ppp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-160
set (router-wan) rip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-162
set (router-wan) stp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-163
set (router-wan) trunk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-165
set (router-wan) up/down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-165
set screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-166
set snmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-167
set time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-168
set user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-169
xviii
Axxius 800 - Release 2.2
Table of Contents
set (v35) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
set (v54) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
set verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show (adpcm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show autoexit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show (bri) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show cclabels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show connect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show connect adpcm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show (ds0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show (ds1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show (ds3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show external alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show (fxo) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show (fxsPS or fxsPSM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show ipds0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show lsprotect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show ntp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show (ocudp). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show (router) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show (router) dhcp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show (router) dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
show (router) dns proxy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Axxius 800 - Release 2.2
5-170
5-172
5-174
5-175
5-176
5-177
5-177
5-178
5-178
5-179
5-180
5-180
5-181
5-182
5-183
5-184
5-184
5-185
5-186
5-186
5-187
5-188
5-189
5-189
5-189
5-190
5-191
5-191
5-192
5-193
5-195
5-196
5-196
xix
Table of Contents
show (router) lmi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-197
show (router) login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-197
show (router) ntp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-198
show (router) port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-199
show (router) ppp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-200
show (router) rip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-201
show (router) snmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-201
show (router) stp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-202
show (router) syslog. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-202
show (router) uploaduser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-203
show (router-lan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-204
show (router-lan) filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-206
show (router-lan) static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-208
show (router-lan) stp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-211
show (router-wan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-212
show (router-wan) firewall. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-214
show (router-wan) nat bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-214
show (router-wan) ppp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-215
show (router-wan) static ip address . . . . . . . . . . . . . . . . . . . . . . . . . . 5-216
show (router-wan) static ip network . . . . . . . . . . . . . . . . . . . . . . . . . 5-216
show (router-wan) static ipx network . . . . . . . . . . . . . . . . . . . . . . . . 5-217
show (router-wan) static mac address . . . . . . . . . . . . . . . . . . . . . . . . 5-217
show (router-wan) static nat address . . . . . . . . . . . . . . . . . . . . . . . . . 5-218
show (router-wan) stp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-218
show (router-wan) trunk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-219
show screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-219
show snmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-220
show syslog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-220
show time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-221
show users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-221
show (v35) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-222
show (v54) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-223
status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-224
xx
Axxius 800 - Release 2.2
Table of Contents
status (adpcm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (adpcm) performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (adpcm) performance history . . . . . . . . . . . . . . . . . . . . . . . . .
status (bri) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (bri) performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (bri) performance history . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (ds0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (ds1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (ds1) performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (ds1) performance history . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (ds3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (ds3) performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (ds3) performance history . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (fxo) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (fxsPS or fxsPSM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status ipds0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status lsprotect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (ocudp) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (ocudp) performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (ocudp) performance history. . . . . . . . . . . . . . . . . . . . . . . . . .
status (router) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (router-lan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (router-trunk) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
status (v54) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
store . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
switch activeimage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
switch controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
switch (ds3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Axxius 800 - Release 2.2
5-225
5-226
5-227
5-228
5-229
5-230
5-230
5-231
5-232
5-233
5-234
5-235
5-236
5-237
5-238
5-239
5-240
5-240
5-241
5-242
5-243
5-244
5-245
5-253
5-254
5-255
5-256
5-257
5-258
5-258
5-258
5-259
5-260
xxi
Table of Contents
telnet (router) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-260
trace route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-261
tracert (router) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-261
6
DS1 Controller Card
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Product Includes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
DS1 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Service Interfaces Supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Network Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Testing and Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Controller Active and Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
CLI Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Built-In Card Handles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
7
DS3 Controller Card
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Product Includes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Network DS3 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Service Interfaces Supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Network Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
xxii
Axxius 800 - Release 2.2
Table of Contents
Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Testing and Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
Controller Active and Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
Controller and DS3 Redundancy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Protection Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Electronics Protection Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Network Protection Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10
Electronics and Network Protection Mode . . . . . . . . . . . . . . . . . . . . . 7-10
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
CLI Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
Built-In Card Handles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12
8
FXO Voice Card
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Software and Hardware Required . . . . . . . . . . . . . . . . . . . .
FXO Transmission Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FXO Signaling Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Card Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLI Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel Associated Signaling (CAS) Conversions . . . . . . . . . . . . . . . . .
Axxius 800 - Release 2.2
8-2
8-3
8-3
8-3
8-3
8-4
8-4
8-4
8-5
8-5
8-6
8-6
8-7
xxiii
Table of Contents
9
ISDN BRI Card
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
ISDN BRI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
3-DS0 BRITE Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Controller Software Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Product Includes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
Network Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
Network Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
Testing & Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
Product Supports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
Card Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6
CLI Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6
LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Wire-Wrap Pinout 2 Wire Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
10
OCU-DP Card
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
Customer Premise Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
SS7 Backhaul Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5
Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5
Controller Software and Hardware Required. . . . . . . . . . . . . . . . . . . . 10-5
Service Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5
Network Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
Loopbacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
xxiv
Axxius 800 - Release 2.2
Table of Contents
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
Card Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7
CLI Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7
Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-8
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9
Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
Line Rates/Line Lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12
Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-13
DDS RJ-48S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-13
Wire-Wrap Pinout 4 Wire Services . . . . . . . . . . . . . . . . . . . . . . . . . 10-14
11
Single Channel POTS Cards
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Software Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FXS Transmission Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Modem Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FXS Signaling Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Built-In Card Handles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Card Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLI Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RJ-11 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Up the Single Channel POTS Line . . . . . . . . . . . . . . . . . . . . . . . .
Set Up the Single Channel POTS Modem . . . . . . . . . . . . . . . . . . . . .
Axxius 800 - Release 2.2
11-2
11-2
11-3
11-3
11-3
11-3
11-3
11-4
11-4
11-5
11-5
11-5
11-6
11-6
11-7
11-8
11-8
11-8
xxv
Table of Contents
12
Power Supply
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2
Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3
Electrical Input Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3
Electrical Output Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4
Interface Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4
Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4
Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5
LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6
Installing/Replacing a Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7
Install a Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7
Remove a Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7
13
Quad DS1 ADPCM Card
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-3
Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-3
Controller Software Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-3
T1 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-3
T1 Interface (continued). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
ADPCM Signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
Network Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5
Testing and Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5
Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5
xxvi
Axxius 800 - Release 2.2
Table of Contents
Card Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6
CLI Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6
Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-8
Cross-Connects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-9
Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-10
Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-11
RJ-48 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-11
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-12
14
Quad T1 & Quad DS1/E1 Card
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-2
Hardened Quad DS1/E1 Service card. . . . . . . . . . . . . . . . . . . . . . . . . 14-2
Hardened Quad T1 Service card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-3
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4
Controller Software Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4
T1 Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4
Network Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4
Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-5
Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-5
Testing and Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-5
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-5
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-6
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-6
Card Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-7
CLI Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-7
Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-8
Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-9
RJ-48 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-9
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-10
Axxius 800 - Release 2.2
xxvii
Table of Contents
15
Terminal Server Router Card
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-2
Quad TSR with TBOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-2
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3
Additional Features on a TSR Card with TBOS . . . . . . . . . . . . . . . . . 15-3
Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-4
Controller Software Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-4
Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-4
WAN Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-4
LAN Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-4
RS-232 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5
Routing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5
Bridging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5
Router Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5
Advanced Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-5
Frame Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-6
Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-6
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-6
MIBs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-6
Equipment Supported for TBOS-to-SNMP Conversion . . . . . . . . . . . 15-7
Testing and Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-7
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-7
Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-7
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-7
Card Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-8
CLI Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-8
Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-17
10Base-T Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-17
RS-232 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-17
TSR Card Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-18
LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-19
xxviii
Axxius 800 - Release 2.2
Table of Contents
16
V.35/.54 Card
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Additional V.54 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Software Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Testing and Diagnostics (V.35/54 card) . . . . . . . . . . . . . . . . . . . . . . .
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Card Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLI Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
V.35 DCE (DB-26) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
16-2
16-3
16-3
16-3
16-3
16-3
16-3
16-3
16-4
16-4
16-4
16-4
16-4
16-5
16-5
16-6
16-7
16-7
16-8
Low Speed Protection Card
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Backup Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Protected Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port Backup and Prioritization:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Software and Hardware Required . . . . . . . . . . . . . . . . . . .
Protection Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switchover Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Cards Supported. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Axxius 800 - Release 2.2
17-2
17-3
17-3
17-3
17-4
17-4
17-4
17-4
17-4
17-5
17-5
17-5
xxix
Table of Contents
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-5
Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-5
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-5
Card Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-6
CLI Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-6
Basic Setup of a Protected System. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-6
LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-8
18
Maintenance
Software Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-2
Loading System Software via TFTP . . . . . . . . . . . . . . . . . . . . . . . . . . 18-2
Loading Router Software via TFTP. . . . . . . . . . . . . . . . . . . . . . . . . . . 18-3
Upgrading System and Router Software via TFTP using Proxy . . . . . 18-5
Upgrading Software Levels via XModem . . . . . . . . . . . . . . . . . . . . . . 18-7
Backup Axxius 800 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-9
Save Controller Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-9
Load Controller Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-10
Hot Swap Service Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-11
A
B
Regulatory Approvals
SNMP Interface
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SNMP Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MIB Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enterprise MIB Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Router Enterprise MIB Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Public MIB Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Router Public MIB Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SNMP Trap Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enterprise Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xxx
B-2
B-2
B-2
B-3
B-4
B-5
B-7
B-8
B-8
B-8
Axxius 800 - Release 2.2
Table of Contents
C
Loopback Tests
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
Test Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
Identify Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
Logs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
Status and Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-7
DS1 Loopbacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-7
DS1 Line Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-7
DS1 Payload Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-9
Receiving DS-1 CSU Loop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-10
DS1 Equipment Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-12
V.35 Loopbacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-14
V.35 Line Loop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-14
V.35 Equipment Loop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-16
V.35/V.54 Loop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-18
V.35/V.54 Service Card Description . . . . . . . . . . . . . . . . . . . . . . . . . C-18
V.54 Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-19
V.54 Equipment Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-20
Glossary
Index
Axxius 800 - Release 2.2
xxxi
Table of Contents
xxxii
Axxius 800 - Release 2.2
CHAPTER
Base Platform
In this Chapter
n
Overview
n
Features
n
Technical Specifications
n
Chassis
n
Built-In Card Handles
n
Management Ports
n
Local and Remote Management
n
Control Panel Interfaces
n
Control Panel LEDs
n
ACO
Base Platform
Overview
Overview
The Axxius 800 Access Integration Platform solves today’s problems of multiple
boxes, scalability, space, power, and environmental constraints associated with
delivering voice and data services. The Axxius 800 defines a new level of functionality
and performance for the access needs of both wireless and wireline service providers,
and enables them to groom and deliver services for more revenue at dramatically lower
costs. Its versatility and scalability in a two rack unit design offers the highest density
and most flexibility to meet the complex network challenges of today and tomorrow.
The Axxius 800's enclosure, commons, and many of the service cards are temperaturehardened and designed to withstand the extreme conditions found in service provider
equipment locations. It is a carrier-quality platform with full redundancy to protect
critical networks. The Axxius 800 Base Platform includes 1+1 Power Supply slots, 1+1
Controller card slots, 1+1 Broadband Interface slots, a Control Panel Interface card,
eight universal Service card slots, and one Low-Speed Interface Protection card slot.
The rear panel of the Axxius chassis is connectorized and designed for the tight
confines of cell sites, outside cabinets, collocations, or central offices. Dual-feed rear
power connectors support power supply redundancy, and inputs for clocking and alarm
connections are easily accessible. In addition, front RJ-48C and rear wire-wrap
terminals provide easy connection points to DSX patch panels from any of the eight
Service card slots.
The DS1 and DS3 Controllers manage the Service cards, providing the physical,
electrical, and logical connections to deliver a complete, integrated, single-unit
solution. The following are the supported Service cards:
l 8-Channel FXO Voice Service card
l Dual V.35/.54 Service card (hardened)
l ISDN BRI Service cards
l OCU-DP Service cards
l Quad DS1 ADPCM Service card (hardened)
l Quad DS1/E1 Service Card (hardened) - E1 supported in future release
l Quad T1 Service card (hardened)
l Single-Channel POTS Service card (hardened)
l Single-Channel POTS Service card with an integrated V.34 modem
l Terminal Server Router (TSR) Service card (hardened)
l Low-Speed Interface Protection card (hardened)
1-2
Axxius 800 - Release 2.2
Base Platform
Features
The Control Panel Interface card provides front access to all the physical interfaces of
the DS1 or DS3 Controller cards. It provides four RJ-48C DS1 connections when using
the DS1 Controller and two sets of DS3 SMB interfaces when using the DS3
Controller. Additionally, the Control Panel Interface Card provides the RS-232 and
10/100Base-TX Ethernet management connections for system configuration and
control. Status indicators are provided for critical, major, minor, and ACO alarm relay
status, and an Alarm Cut Off (ACO) Switch is also provided to silence external audible
alarms.
Note: In the event of a power failure to the unit (5V in the backplane), there are relays
that will cut 1 to 3 and 2 to 4. These relays are hard-wired to +5V, so al long as there is
power, the cut-through does not happen (there is no software control of this feature).
Features
l 24 or 48 VDC power options
l High service availability through circuit protection, redundancy, remote
provisioning and hot-swappable service cards
l All cards hot-swappable
l Supports fully protected Ring, Star, and Cascade network topologies
l High interface density and versatility. 8 service slots for: T1, V.35
l
l
l
l
l
l
10/100Base-T Ethernet, RS-232, POTS, OCU-DP, FXO and ISDN BRI service
cards and Terminal Server Router card for 10/100Base-TX Ethernet
Simplified installation with front access modular or rear wire-wrap connectors
19 or 23 inch rack mountable, 2 RU, passively cooled
10 user-defined alarm inputs
Audio and visual alarm outputs
Primary and secondary BITS clock inputs for external timing source
Operating temperature ranges -40 to 149 ºF (-40 to 65 ºC)
Axxius 800 - Release 2.2
1-3
Base Platform
Controllers
Controllers
The Axxius 800 has two controllers available, one controller can support the system,
however with two controller (same type) the system is redundant.
Dual DS3 Controller
Features two DS3 ports with integrated 3/1/0 cross-connect matrix, providing nonblocking connectivity between the DS3 Controller and any of the 8 service card slots.
Quad DS1 Controller
Features four DS1 ports with integrated CSUs and a built-in 1/0 cross-connect matrix,
providing full, non-blocking connectivity between the controller and any of the 8
service card slots.
Service Cards
All Service cards are hot-swapable and can be installed in any of the 8 service slots of
the Axxius 800 chassis, with the exception of the Low Speed Protection card, which
has a defined slot.
FXO Service card
The FXO service card is an 8 port Foreign Exchange Office (FXO) or Dial Pulse
Termination (DPT) line card. Delivers high-density provisioning of Direct Inward
Dialing (DID) or FX0 telephone services from T1 access circuits.
ISDN BRI Service card
The ISDN Basic Rate Interface (BRI) service card is available in a Dual, Quad or Octal
port option. The ISDN BRI service delivery interfaces enable delivery of high-density,
standards based, ISDN BRI services of T1 access circuits.
1-4
Axxius 800 - Release 2.2
Base Platform
Service Cards
OCU-DP Service card
The OCU-DP service card is available in a Single or Quad port option. The OCU-DP
interface service allows Digital Data Service (DDS) circuit terminations on the Adit
600 platform. Provides the electrical and physical termination of a 4-wire DDS
baseband connection which interfaces with a remote CSU/DSU.
POTS Service card
A Single Channel POTS card provides wireless service providers a standard FXS voice
circuit for communications, with the operations support group under conditions where
the cell site radios are being serviced.
Quad DS1 ADPCM Service card
The 4 port T1 service card can compress and groom voice traffic, which increases
bandwidth utilization and reduces costs. Using Adaptive Differential Pulse Code
Modulation (ADPCM), this card compresses selected voice timeslots from one of the
T1 ports.
Quad DS1/E1 and T1 Service cards
The 4 port T1 service card enables cost-effective provisioning and expansion of T1
bandwidth with full non-blocking digital cross-connection of all timeslots to any
Axxius service card. E1 capability will be supported in a future release.
V.35/54 Service cards
The Dual port V.35 interface service card provides connectivity to high-speed serial
synchronous Data Terminal Equipment (DTE) devices.
Terminal Server Router (TSR) Service card
The Terminal Server Router card provides all IP Router card functions and features,
with the added features of a selectable four port RS-232 and 10/100Base-TX Ethernet
switch with dedicated routing functionality. There is an option of this card which
provides TBOS.
Axxius 800 - Release 2.2
1-5
Base Platform
Power Supplies
Low Speed Protection card
Low speed protection provides backup circuitry for any T1 service port on any Quad
T1 service card in the Axxius chassis. The Relay card provides the physical
connectivity between the “Protected” T1 service port and the “Backup” T1 service port.
Connectivity exists between the Quad T1 service card and the Relay card via the
backplane pins only.
Power Supplies
24 VDC Power Supply
Provides the a standard +24 VDC power supply.
48 VDC I48 Power Supply
Provides the standard -48 VDC power supply.
48 VDC NI48 Power Supply
Provides non-isolated -48 volt to the backplane, to support the FXO and OCU-DP
Service cards.
Technical Specifications
Platform Features
l System Controllers (1 + 1 redundancy)
l Hot-swappable manager, power, and service cards
l Power supplies (1 + 1 redundancy)
l Integrated 3/1/0 digital cross-connect
l TDM transport, Add/Drop, Drop-and-Insert
l Front and rear access for service and network interfaces
1-6
Axxius 800 - Release 2.2
Base Platform
Technical Specifications
Capacities
l 2 x Power Supply cards
l 2 x DS3 or DS1 Controller cards
l 1 x Control Panel Interface card
l 8 x universal service cards
l 36 T1 ports (8 x Quad T1 service cards + 4 on DS1 Controller)
l 1536 DS0 non-blocking cross-connect capability
Redundancy
l 1:1 Controllers (automatic switchover) for provisioning redundancy
l 1:7 T1 interface protection ratio with Low-Speed Interface Protection card
l 1 + 1 Power Supplies
Control Panel Interfaces
l 4 x RJ-48C jacks (Quad DS1 Controller)
l 4 x SMB connectors (2 TX, 2 RX) for DS3 Controller
l 1 x 10/100Base-TX Ethernet RJ-45 jack
l 1 x RS-232 DB9 female jack
l 1 x ACO switch
l Status indicators for critical, major, minor and ACO
Rear Chassis Interfaces
l 8 x 16 wire-wrap pins
l 2 x 2 pin modular plug for dual DC power feeds
l 2 x 3 wire-wrap pins for BITS clock input (primary and secondary)
l 2 x 6 pin modular receptacle for alarm relay outputs
l Audible alarm outputs (3) critical, major and minor
l Visible alarm outputs (3) critical, major and minor
l 2 x 10 pin modular receptacle for environmental monitor inputs
l 2 x 3/16 inch threaded stud for grounding
Axxius 800 - Release 2.2
1-7
Base Platform
Technical Specifications
Alarm Connectors
The alarm contact outputs are per Telcordia definitions for visible and audible. They
operate per the spec with the exception that the audible outputs can be disabled with the
ACO button.
l The alarm output contacts are designed for use at 48V nominal with a current
draw of 0.5A maximum.
l The alarm inputs are dry contact with a current capacity of 10mA.
Network Standards
l ANSI/TIA - T1.403 ESF FDL
Management
l Craft Interface - front access from RS-232 (DB9) or 10/100Base-TX Ethernet
ports
l SNMP
l Dedicated Management DS0 for remote management access
Power
l DC Power: -48 VDC or +24 VDC, 120 W rated input
l OCU-DP and FXO Service cards require -48 VDC Power Supply
l Dual-feed power inputs located on rear panel
Physical Information
l Dimensions: 3.5 in. (H-2 RU) x 17.25 in. (W) x 12.5 in. (D)
8.9 cm (H) x 43.8 cm (W) x 31.75 cm (D)
l Weight: approximately 30 lbs. (13.6 kg) fully loaded
l Rack mount, 19 or 23 inch
Environment
See Installation Environment on page 2-3
1-8
Axxius 800 - Release 2.2
Base Platform
Chassis
Chassis
Future Development
Power
Supplies
(P1 & P2)
Controller
Cards
(A1 & A2)
Ground Terminals
Interface
Card
Future
Development
Slot 1-8 Wire-Wrap Connectors
Axxius 800 - Release 2.2
Service Card
Slots 1-8
BITS
Visible Clock
Alarms 1 and 2
Audible
Alarms
Relay
Card
Power
P1 and P2
External
Alarm
Inputs
1-9
Base Platform
Built-In Card Handles
Built-In Card Handles
Several of the cards for the Axxius 800 are designed with a handle built into the
faceplate to assist in the removal of the card from the chassis. This handle slides out
away from the unit, creating a handle for a more effective grip. The Controller cards
and the Single Channel POTS card have this feature.
Management Ports
RS-232 Craft Port
The Axxius 800 contains an RS-232 craft port for connection through any VT100
terminal, PC, or modem for remote management using the Command Line Interface.
10/100Base-T Ethernet Port
A 10/100Base-T Ethernet Port available for management on the Controller card.
Local and Remote Management
The Controller cards have several local and remote management options available.
Front-panel LEDs quickly communicate alarm, system and line status. The cards can
be configured and managed locally through the RS-232 or Ethernet management
connections on the Interface card using a Command Line Interface (CLI).
A number of remote management options are available to reduce truck roll costs for
most maintenance and troubleshooting activities. The in-band DS0 management
channel on the controller delivers 64 Kbps remote access to the Axxius 800 without
incurring additional facilities costs. Alternatively, as separate Ethernet facility can be
deployed to support out-of-band SNMP network management, and the controller can
also be accessed through the V.34 dial-in modem connection from the Single Channel
POTS with V.34 Modem Service card. Remote configuration, monitoring,
maintenance, and troubleshooting tasks are further simplified from the central Network
Operation Center (NOC) using the graphical interfaces of the NetworkValet EMS.
1-10
Axxius 800 - Release 2.2
Base Platform
Control Panel Interfaces
Control Panel Interfaces
10Base-T
Ethernet
RS-232
DS3 (SMB)
Connectors (4)
DS1 (RJ-48)
Connectors (4)
SMB connector (female)
The recommended mate for the SMB connector is an SMB right angle crimp connector.
Axxius 800 - Release 2.2
1-11
Base Platform
Control Panel Interfaces
RS-232 Craft Port (Female DB-9)
The RS-232 craft port connects via a
female DB-9 connector on the Axxius
800.
1
5
6
9
The pinouts are as follows:
Pin Number
Direction
Description
1
Outbound
Carrier Detect
2
Outbound
Receive Data
3
Inbound
Transmit Data
4
Inbound
Data Terminal Ready
5
6
Outbound
Data Set Ready
7
Inbound
Request to Send
8
Outbound
Clear to Send
9
1-12
Signal Ground
Not Connected
Axxius 800 - Release 2.2
Base Platform
Control Panel Interfaces
DS1 Connection Ports
1
8
1
8
The DS1 connection ports are each equipped with a standard
RJ-28C (female) on the Axxius 800 unit.
The pinouts are as follows:
DS1 (RJ-48C)
Pin
Name
Description
1
Receive Ring
Receive from DS1 network
2
Receive Tip
Receive from DS1 network
3
N/C
Not connected
4
Transmit Ring
To DS1 network
5
Transmit Tip
To DS1 network
6 -8
N/C
Not connected
10/100Base-T Ethernet
The 10/100Base-T Ethernet (female) port to connect to a remote
management tool such as Telnet or an SNMP-based Network
Management System.
The pinouts are as follows:
Ethernet (RJ-45)
Pin
Name
Description
1
Receive +
Receive from network
2
Receive -
Receive from network
3
Transmit +
Transmit to network
4
N/C
Not connected
5
N/C
Not connected
6
Transmit -
Transmit to network
7-8
N/C
Not connected
Axxius 800 - Release 2.2
1-13
Base Platform
Control Panel Interfaces
Control Panel Interface Card Jumpers
The Control Panel Interface card is provided with a jumper that allows the user to put
a -3 dB pad in the transmit DS3 signal path to lower the output to a shorter line length.
This prevents errors when working with very short cables.
There is a simple drawing to assist in setting the Control Panel Interface jumpers.
The jumpers in the second graphic are set to the position farthest from the faceplate,
they are set to -3dB.
1-14
Axxius 800 - Release 2.2
Base Platform
Control Panel LEDs
Control Panel LEDs
Alarm LEDs
LED
State
Description
CRITICAL
Off
No critical alarms present
Red
Critical alarms present
Off
No major alarms present
Red
Major alarm present
Off
No minor alarms present
Red
Minor alarms present
Off
Normal mode. No alarms are being suppressed.
Red
Alarm cutoff active. One or more active alarms
suppressed.
MAJOR
MINOR
ACO
Axxius 800 - Release 2.2
1-15
Base Platform
Control Panel LEDs
Ethernet LEDs
LED
State
Description
STATUS
Off
Link Down
Green
Link Up
Flashing Green
Traffic on Link
When Status LED is on or flashing:
1-16
LED
State
Description
10/100
Off
Link is 10 Mb
Green
Link is 100 Mb
Axxius 800 - Release 2.2
Base Platform
ACO
ACO
The Alarm Cutoff feature permits the operator to temporarily silence the alarm outputs
while testing and repairing the Axxius 800. ACO does not stop alarm messages.
Pressing the ACO pushbutton switch disables the alarm relays and lights the ACO
status LED. This keeps the relay contacts open on the Alarm Output connector. If
another alarm occurs, the alarm relays will be enabled again and the ACO status LED
will go off.
Alarm Cutoff disables the following signals on the Alarm Output connector:
l Critical alarm
l Major alarm
l Minor alarm
The operator also has the option of using the CLI command aco, see aco (Alarm Cut
Off) on page 5-5.
Axxius 800 - Release 2.2
1-17
Base Platform
ACO
1-18
Axxius 800 - Release 2.2
CHAPTER
Physical Installation
In this Chapter
n
Unpacking and Inspection
n
Installation Environment
n
Assembly of Axxius 800
n
Rack Mounting
Physical Installation
Unpacking and Inspection
Unpacking and Inspection
WARNING! OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC
DEVICES.
1. Inspect containers for damage during shipment. Report any damage to the
freight carrier for possible insurance claims.
2. Compare packing list with office records. Report any discrepancies to the
office.
3. Open shipping containers, be careful not to damage contents.
4. Inspect contents and report any damage.
5. If equipment must be returned for any reason, carefully repack equipment in
the original shipping container with original packing materials if possible.
6. If equipment is to be installed later, replace equipment in original shipping
container and store in a safe place until ready to install.
2-2
Axxius 800 - Release 2.2
Physical Installation
Installation Environment
Installation Environment
The environment in which you are installing the Axxius 800 must meet the following
conditions:
DANGER! RESTRICTED ACCESS LOCATION FOR ACCESS 800: ACCESS CAN
ONLY BE GAINED BY SERVICE PERSONNEL OR USERS WHO HAVE BEEN
INSTRUCTED ABOUT THE POTENTIAL SAFETY HAZARDS THAT EXIST. ACCESS
CAN ONLY BE GAINED TO THE EQUIPMENT LOCATION BY THE USE OF A TOOL OR
LOCK AND KEY. TAKE PRECAUTIONS WHEN INSTALLING/SERVICING THE
EQUIPMENT. HAZARDOUS ENERGY LEVELS EXIST ON THE POWER SUPPLY.
BARE TELECOMMUNICATION NETWORK WIRING IS EXPOSED ON THE REAR
PANEL. DISCONNECT FROM NETWORK BEFORE INSTALLING WIRE-WRAP
CONNECTIONS.
NOTE: Installation of unit in Operator Access Locations is possible for 48V
powered units under certain circumstances. Please contact Customer
Service for information on the Axxius DC Input Shroud Kit P/N 790-0027.
l Operating temperature range: -40° to 149° F (-40° to 65° C)
*please see items following that do not operate within this range
l V.34 modem operating temperature range: 32° to 149° F (0° to 65° C)
l FXO, ISDN BRI, and OCU-DP service cards operating temperature range:
32° to 104° F (0° to 40° C)
l Storage temperature range: -40° to 158° F (-40° to 70° C)
l Cooling method is by free air convection
l Maximum operating altitude: 10,000 ft. (3,048 m)
l Minimum operating altitude: 197 ft. (60 m) below sea level
l Maximum non-operating altitude: 40,000 ft. (12,192 m)
l Relative humidity (non-condensing) range: 0 to 95%
Axxius 800 - Release 2.2
2-3
Physical Installation
Assembly of Axxius 800
Assembly of Axxius 800
The cards should be positioned according to the following guidelines:
l Power Supply(s) 24 or 48 VDC
Single Power Supply - slot Power 1 or Power 2
Dual Power Supplies - slot Power 1 and Power 2
l Controller card(s) DS1 or DS3
Single controller card - slot A1 or A2
Dual controller cards - slot A1 and A2
l Interface card
The Interface card is designed with two boards that follow a single guide.
l Service Cards can be in any slot 1 through 8.
Note: Cards that use the front cable connections should be loaded from Slot 8
to 1. This will minimize card access issues due to cable interference.
l Relay Card in the Relay slot.
l Always install blank faceplates in any unused slots.
Future Development
Power
Supplies
(P1 & P2)
2-4
Controller
Cards
(A1 & A2)
Interface
Card
Service Card
Slots 1-8
Relay
Card
Axxius 800 - Release 2.2
Physical Installation
Rack Mounting
Rack Mounting
The Axxius 800 can be mounted on a 19 or 23 inch rack with Carrier Access mounting
brackets.
NOTE: The Axxius 800 requires at least 3/4 inches of free air space above
and below the chassis (approx 1/2 RU) for air circulation.
Always leave at least 14" clearance in front of the unit, to add and remove cards.
Axxius 800 mounted to a 19" rack with mounting brackets
Bracket Ears
to the front
Bracket Ears
to the back
Axxius 800 - Release 2.2
Axxius
Front
Depending on the
customer needs
the mounting
brackets can be
mounted with
fingers to the
front or to the back
of the unit
2-5
Physical Installation
Rack Mounting
To maintain proper convection cooling, maintain at least 1/2 RU between the Axxius
and any other equipment (each Axxius occupies 3 RU of rack space). Therefore, if one
Axxius is mounted above another Axxius, then there would be a total of 1 RU between
them (1/2 RU above the lower unit and 1/2 RU below the upper unit).
Using the 1/2 RU airspace guideline, up to 15 Axxius 800 units may be installed in a
7’ equipment rack.
1
}
2
1/2 RU free space
1/2 RU free space
1/2 RU free space
3
1/2 RU free space
4
5
6
7
8
9
Axxius = 2 RU
Spacing = 1RU
(1/2 above 1/2 below)
10
11
12
13
14
15
2-6
Axxius 800 - Release 2.2
CHAPTER
Electrical Installation and Cabling
In this Chapter
n
Compliant Installation
n
Chassis Connections
n
Power Connections
n
External Alarm Inputs
n
Visible and Audible Alarms
n
BITS Clock 1/BITS Clock 2
n
Slot (1-8) Wire-Wrap Connectors
Electrical Installation and Cabling
Compliant Installation
Compliant Installation
WARNING! ALL TELECOMMUNICATION NETWORK CONNECTIONS MUST USE
MINIMUM
26 AWG WIRE.
1. Mount unit in an area that meets Environment conditions, see Installation
Environment on page 2-3.
2. Unit should have power supply(s), controller(s) and Interface cards installed
before power up.
NOTE: All cards (power supplies, controllers, interface, relay and service)
slide into the unit in the same manner. There are guides for each slot (top
and bottom), which the card follows until it is firmly seated into the
backplane.
3. Ground the system, secure the ground lugs to the terminals using the nuts
provided. Attach #6 or #8 AWG copper wire to the terminal.
4. Install service cards.
5. Install blank faceplates in any slot that is not occupied.
6. Connect BITS Clock 1 and/or 2
7. Connect Alarming
8. Secure the power cable and the ground cable with a plastic tie (not included).
Keep these cables separate from the signal cables.
9. Terminate each signal cable to its appropriate connector.
10. Secure the signal cables using the small holes along the bottom of the rack and
plastic ties (not included).
11. Plug in power, to the system, apply the appropriate power for the installed
Power Supply(s)
3-2
Axxius 800 - Release 2.2
Electrical Installation and Cabling
Compliant Installation
Ferrite Beads
To be compliant with FCC Part 15 EMI limits with the Quad DS1 ADPCM service card
installed:
l Route alarm cables separate from the rear panel tip/ring cabling (wire wrap
pins).
l Install ferrite bead accompanying this card on the visible, audible and
environmental input alarm cable bundle
Ferrite beads shipped with Quad DS1 ADPCM card:
Ferrite Provided
Part Number
Intended For
1 large
P/N 010-0051
Alarm cable
Axxius 800 - Release 2.2
3-3
Electrical Installation and Cabling
Chassis Connections
Chassis Connections
The following illustrations show all connectors on the rear, as well as the front
(interface card) of the Axxius 800.
Visible
Alarms
Ground Terminals
Slot 1-8 Wire-Wrap Connectors
Power Connectors
A and B
Clock
A and B
Audible
Alarms
External
Alarm
Inputs
Back of the Axxius 800:
l
l
l
l
l
l
l
3-4
Audible Alarms
External Alarm Inputs
Visible Alarms
Input (power, P1 and P2)
Bits Clock 1 and 2
Wire-Wrap Connectors (slots 1-8)
Ground Lugs
Axxius 800 - Release 2.2
Electrical Installation and Cabling
Chassis Connections
10Base-T
Ethernet
RS-232
DS3 (SMB)
Connectors (4)
DS1 (RJ-48)
Connectors (4)
Front of the Axxius 800 - Interface Card
l
l
l
l
10Base-T Ethernet (RJ-45)
RS-232 Craft Port
DS3-1 and 2 Transmit and Receive connectors (SMB)
DS1 (1-4) connectors (RJ-48)
For information on this card and all connectors see Control Panel Interfaces on page 1-11.
CAUTION! THE AXXIUS 800 CONTAINS CIRCUIT CARDS AND COMPONENTS THAT
ARE SUBJECT TO DAMAGE BY ELECTROSTATIC DISCHARGE (ESD). ALWAYS
FOLLOW THE ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS, ON PAGE XXII.
Axxius 800 - Release 2.2
3-5
Electrical Installation and Cabling
Chassis Connections
Chassis Ground Connector
Ground Terminals
1. Route wire (#6 or #8 AWG copper) from building ground to lug on Axxius 800.
2. Strip insulation off wire end, if necessary.
Ground Lug
Compression
Screw
Lug Barrel
3. Loosen compression screw until opening is large enough to accept ground wire.
4. Insert ground wire into lug barrel, beneath compression plate and tighten
compression screw.
5. Attach ground lug to chassis
3-6
Axxius 800 - Release 2.2
Electrical Installation and Cabling
Chassis Connections
Power Connections
There are three power supplies available with the Axxius 800; 24 VDC and 48 VDC
and 48 VDC NI, all use this connector. The Axxius 800 supports a redundant power
system, therefore there is INPUT (power) P1 and P2.
Input Power
Power Supply
Rated Amperage
Recommended External
Input Fuse
24 VDC
5 Amp
7 Amp
48 VDC/48 VDC NI
2.5 Amp
3.5 Amp
A separate fuse should be used for each DC input
NOTE: If two power supplies are installed into the system they MUST be
of the same type (24 VDC, 48 VDC or 48 VDC NI).
Wire each connector to a power source:
1. Ensure that no power is present on the two wires to be connected.
DANGER! POSSIBLE SHOCK HAZARD EXISTS, PLEASE FOLLOW
INSTRUCTIONS CAREFULLY.
2. Strip the two wires from the power source so that approximately 5/16 inch of
bare wire is exposed. 16 or 18 AWG insulated copper wire is recommended
for power connections.
3. Insert the Battery Return and DC wires into the appropriate square holes, one
at a time.
4. Tighten screws to clamp wires.
Axxius 800 - Release 2.2
3-7
Electrical Installation and Cabling
Chassis Connections
5. Ensure that no bare wire shows after the wires are installed.
Provided Connector (male)
Tighten screws
to clamp wires
Set Screw
+
-
6. Plug connector in the INPUT (power) connector, as seen in the graphic and
secure with set screws.
7. Apply power to connector.
8. Verify with voltmeter that voltage is correct and polarity is correct.
9. Plug connector(s) into the Axxius 800.
10. A green light should appear on the DC Input LED on the front of the Power
Supply.
3-8
Axxius 800 - Release 2.2
Electrical Installation and Cabling
Chassis Connections
External Alarm Inputs
The external alarm input connector supports 10 alarm inputs and is composed of two
10-pin connectors (two input pairs for each).
External Alarm Input
1. Strip wire so that approximately 5/16 of bare wire is exposed.
back of Axxius
Connector plugged into Axxius
Tighten screw
to clamp wire
Set screw
Wire
2. Insert wire into opening and tighten screw to clamp wire.
3. Ensure that no bare wire shows after the wires are installed.
4. Plug connector in the EXTERNAL ALARMS INPUTS connector, as seen in
the graphic above and secure with set screws.
Axxius 800 - Release 2.2
3-9
Electrical Installation and Cabling
Chassis Connections
Visible and Audible Alarms
The external alarm connectors are six-pin connectors with two output pairs for each
alarm level (pins 1 & 2 for minor, pins 3 & 4 for major and 5 & 6 for critical alarms).
Visible Alarm
Audible Alarm
1. Strip wire so that approximately 5/16 of bare wire is exposed.
pin 1
back of Axxius
Wire
Connectors plugged into Axxius
Set screw
Tighten screw
to clamp wire
2. Insert wire into opening and tighten screw to clamp wire.
3. Ensure that no bare wire shows after the wires are installed.
4. Plug connector in the AUDIBLE ALARMS or VISIBLE ALARMS connector,
as seen in the graphic above and secure with set screws.
3-10
Axxius 800 - Release 2.2
Electrical Installation and Cabling
Chassis Connections
BITS Clock 1/BITS Clock 2
The external alarm connectors are three-pin wire-wrap connectors. One for each, Tip
(T), Ring (R) and Shield (S). Tip and Ring are the two connections for the 100 ohm
differential signal to the box. Shield is for grounding the shield of the clock cable to the
Axxius. If the customer is not using shielded cable, then only the Tip and Ring is
connected.
Bits Clock 1 and 2
back of Axxius
Axxius 800 - Release 2.2
3-11
Electrical Installation and Cabling
Chassis Connections
Slot (1-8) Wire-Wrap Connectors
The Axxius 800 provides wire-wrap connectors for each slot (1-8) of the unit. Pinouts
are clearly labeled with the pins.
CAUTION! DISCONNECT FROM NETWORK BEFORE INSTALLING WIRE-WRAP
CONNECTIONS.
Wire-Wrap Connectors
3-12
Axxius 800 - Release 2.2
Electrical Installation and Cabling
Chassis Connections
Wire-Wrap Pinout for 4 Wire Services
Wire-Wrap Pins
T1
Name
Description
1TX
Port 1
Transmit Ring
To DS1 network
Transmit Tip
To DS1 network
Receive Ring
Receive from DS1 network
Receive Tip
Receive from DS1 network
Transmit Ring
To DS1 network
Transmit Tip
To DS1 network
Receive Ring
Receive from DS1 network
Receive Tip
Receive from DS1 network
Transmit Ring
To DS1 network
Transmit Tip
To DS1 network
Receive Ring
Receive from DS1 network
Receive Tip
Receive from DS1 network
Transmit Ring
To DS1 network
Transmit Tip
To DS1 network
Receive Ring
Receive from DS1 network
Receive Tip
Receive from DS1 network
1RX
2TX
Port 2
2RX
3TX
Port 3
3RX
4TX
4RX
Axxius 800 - Release 2.2
Port 4
3-13
Electrical Installation and Cabling
Chassis Connections
Wire-Wrap Pinout 2 Wire Services
3-14
Wire-Wrap Pins
Description
T1
Channel 1 Tip
R1
Channel 1 Ring
T2
Channel 2 Tip
R2
Channel 2 Ring
T3
Channel 3 Tip
R3
Channel 3 Ring
T4
Channel 4 Tip
R4
Channel 4 Ring
T5
Channel 5 Tip
R5
Channel 5 Ring
T6
Channel 6 Tip
R6
Channel 6 Ring
T7
Channel 7 Tip
R7
Channel 7 Ring
T8
Channel 8 Tip
R8
Channel 8 Ring
Axxius 800 - Release 2.2
Electrical Installation and Cabling
Chassis Connections
Standard Telco Color Code
Circuit connections are made at the wire-wrap connectors. The pinouts are as follows:
Pair
Pin Location
Function
Color Code
1
26
1
Tip Channel 1
Ring Channel 1
White/Blue
Blue/White
2
27
2
Tip Channel 2
Ring Channel 2
White/Orange
Orange/White
3
28
3
Tip Channel 3
Ring Channel 3
White/Green
Green/White
4
29
4
Tip Channel 4
Ring Channel 4
White/Brown
Brown/White
5
30
5
Tip Channel 5
Ring Channel 5
White/Slate
Slate/White
6
31
6
Tip Channel 6
Ring Channel 6
Red/Blue
Blue/Red
7
32
7
Tip Channel 7
Ring Channel 7
Red/Orange
Orange/Red
8
33
8
Tip Channel 8
Ring Channel 8
Red/Green
Green/Red
9
34
9
Tip Channel 9
Ring Channel 9
Red/Brown
Brown/Red
10
35
10
Tip Channel 10
Ring Channel 10
Red/Slate
Slate/Red
11
36
11
Tip Channel 11
Ring Channel 11
Black/Blue
Blue/Black
12
37
12
Tip Channel 12
Ring Channel 12
Black/Orange
Orange/Black
13
38
13
Tip Channel 13
Ring Channel 13
Black/Green
Green/Black
14
39
14
Tip Channel 14
Ring Channel 14
Black/Brown
Brown/Black
Axxius 800 - Release 2.2
3-15
Electrical Installation and Cabling
Chassis Connections
Pair
3-16
Pin Location
Function
Color Code
15
40
15
Tip Channel 15
Ring Channel 15
Black/Slate
Slate/Black
16
41
16
Tip Channel 16
Ring Channel 16
Yellow/Blue
Blue/Yellow
17
42
17
Tip Channel 17
Ring Channel 17
Yellow/Orange
Orange/Yellow
18
43
18
Tip Channel 18
Ring Channel 18
Yellow/Green
Green/Yellow
19
44
19
Tip Channel 19
Ring Channel 19
Yellow/Brown
Brown/Yellow
20
45
20
Tip Channel 20
Ring Channel 20
Yellow/Slate
Slate/Yellow
21
46
21
Tip Channel 21
Ring Channel 21
Violet/Blue
Blue/Violet
22
47
22
Tip Channel 22
Ring Channel 22
Violet/Orange
Orange/Violet
23
48
23
Tip Channel 23
Ring Channel 23
Violet/Green
Green/Violet
24
49
24
Tip Channel 24
Ring Channel 24
Violet/Brown
Brown/Violet
25
50
25
Not used/Spare at this
time
Violet/Slate
Slate/Violet
Axxius 800 - Release 2.2
CHAPTER
Configuration
In this Chapter
n
Setting up a CLI Connection
n
System Information
n
Basic System Setup
n
Quick Configuration Reload
n
Setup of DS0 Management Channel
Configuration
Setting up a CLI Connection
Setting up a CLI Connection
NOTE: The Default IP address of the Axxius 800 Controller (DS1 or DS3)
is 10.0.0.10.
To connect to the CLI, set up the connection:
l If connecting via the ethernet 10Base-T connection, use a Telnet TCP/IP
program to access the CLI. This requires an IP address of the Controller. The
Controllers are shipped with the IP address set to 10.0.0.10, if this address has
been changed and is not known, use HyperTerm to access the Controller and
use the CLI command show ip. If an IP address needs to be set use the CLI
command set ethernet ip address {ip-addr}.
l If connecting via RS-232 (HyperTerm), the port settings should be set to:
Bits per second: 9600
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
l Set your Terminal Emulation to: VT100
NOTE: Note: When using Tera Term TCP/IP, CLI commands will not be
recognized until the following setup is completed.
l In Tera Term go to Setup/Terminal.
l Set the New-line/Transmit value "CR+LF".
4-2
Axxius 800 - Release 2.2
Configuration
System Information
System Information
Once a management session has bee initiated (Telnet or Hyperterm) the system
information will be displayed similar to the following:
Carrier Access - Axxius Product Line
02:03:08 01/01/2002
Login: helen
Status Equipment:
CardType
Status
+24 V
Healthy
Card not installed
SW Vers
SLOT P1
SLOT P2
CLEI
SIPUMR0DAA
SLOT A1
SLOT A2
T1x4
Active
Card not installed
1.0.1
SIIX4W0DAA
SLOT B1
SLOT B2
Card not installed
Card not installed
SLOT
SLOT
SLOT
SLOT
SLOT
SLOT
SLOT
SLOT
TSRx4
T1x4
V35x2
V35x2
T1x4
T1x4
T1x4
FXSPSMx1
1.00
1.73
2.01
2.01
NOT AVAIL
SIIXFWBDAA
SIC3HK0CAA
SIC3HK0CAA
1
2
3
4
5
6
7
8
Present
Present
Present
Present
Not Present
Not Present
Not Present
Present
0.01
Alarms:
Time
Date
Severity Description
00:00:14 01/01/2002 Major
1:1-TSR Ethernet Link Down
Total=1
Status Sessions:
Session
User
Login Port
* TELNET2
helen
10.0.0.0
* indicates current session
Show Autoexit:
Autoexit is off.
Axxius 800 - Release 2.2
4-3
Configuration
Basic System Setup
Basic System Setup
Initial Setup
Use the following commands for your initial setup, for further information see the
specific command listed in Chapter 5, CLI Commands.
Command
Description
set date dd/mm/yyyy
Set the system date, using the format
day/month/year. See the set date command for
details.
set time {hh:mm:ss}
Set the system time. See the set time command
for details.
set id {“id-name”}
Set the systemID name. Remember to enclose
this name in quotes. See the set id command for
details.
set clock {nonrevertive|
revertive|switch}
Set the signal clock switching. See the set clock
command for details.
set {clock1|clock2} {source}
Set the primary and secondary clock source.
See the set clock (1 and 2) command for details.
set ethernet ip address
{ip-addr} [mask]
Set the Ethernet IP address and optionally the
subnet mask, for the Axxius 800. See the set
ethernet ip address command for details.
set ip gateway {ip-addr}
Set the IP gateway for the Axxius 800. See the
set ip gateway command for details.
clear log
Initialize the event log. See the clear key
command for details.
status equipment [slot]
See the status of the equipment. See the status
equipment command for details.
NOTE: Removing an active Controller is not recommended, use the
switch controller command to change the Active Controller to Standby and
then remove the Controller card.
4-4
Axxius 800 - Release 2.2
Configuration
Basic System Setup
Set Up Security
Use the following commands to set up the security on the Axxius 800.
Command
Description
set user {"user-name"}
level {1-3}
Specify the user name and the security level.
See set user command for details.
set user {"user-name"}
password
Set a password for the user. See set user
command for details.
Set Up IP Addresses for Telnet CLI
Use the following commands to setup Telnet addresses for Command Line Interface
(CLI).
Command
Description
set ethernet ip address
{ip-addr} {mask}
Set the Ethernet IP address, in the
conventional IP address format. See the set
ethernet ip address command for more
details.
set ip gateway {ip-addr}
Set the IP gateway, in the conventional IP
address format. See the set ip gateway
command for more details.
Upgrade the Axxius 800 Software
Use the following commands to determine the Controller software level, then upgrade
the software to the latest version.
Command
Description
status equipment
Determine the software level. See the status
equipment command for more information.
load tftp {ip-addr} {"filename"} (or load xmodem)
Load the new software to the Axxius 800.
See the load tftp and load xmodem
command for more information.
Axxius 800 - Release 2.2
4-5
Configuration
Basic System Setup
Set Up a DS0/Channel
Use the following commands to set up a DS0.
Command
Description
set {ds0-addr} type
{data|voice}
Set the channel type. See set (ds0) command
for details.
set {ds0-addr} signal
{ls|gs|emw|emdw|emi|emicpd}
Set the signaling option for the channel. See
set (ds0) command for details.
Set Up a DS1/T1
Use the following commands to set up a DS1/T1. See the set (ds1) command for more
details.
4-6
Command
Description
set {ds1-addr} up
Activate the port.
set {ds1-addr} fdl
{none|t1403}
Set the Facilities Data Link (FDL)
capabilities.
set {ds1-addr} framing
{d4| esf}
Set the framing option for the DS1.
set {ds1-addr} id
{"id-name"}
Set the circuit identification name for the
DS1.
set {ds1-addr} lbo {1-8}
Set the line buildout value for the DS1.
set {ds1-addr} linecode
{ami|b8zs}
Set the linecode for the DS1.
set {ds1-addr} loopdetect
{on|off}
Set the detection/reaction to CSU
loopcodes.
set {ds1-addr} threshold
{day|min15} {bes|css|dm|es
|lcv|les|pcv|sefs|ses|uas)
Set default thresholds for the DS1.
Axxius 800 - Release 2.2
Configuration
Basic System Setup
Set Up a DS3
Use the following commands to set up a DS3. See the set (ds3) command for more
details.
Command
Description
set {ds3-addr} up
Activate the port.
set {ds3-addr} id
{"id-name"}
Set the DS3 ID.
set {ds3-addr} clock
{loop|normal}
Set the transmit clock source.
set {ds3-addr} berthreshold
{value}
Set the Bit Error Rate protection switchover
threshold.
set {ds3-addr} dejitter
{off|on}
Set the De-jitter buffer on or off.
set {ds3-addr} equipment id
{"string"}
Set the DS3 equipment PMDL ID string.
set {ds3-addr} facility id
{"string"}
Set the DS3 facility PMDL ID string.
set {ds3-addr} frame
{"string"}
Set the DS3 frame PMDL ID string.
set {ds3-addr} framing
{cbit|m23}
Set the framing option for the DS3.
set {ds3-addr} location id
{"string"}
Set the DS3 location PMDL ID string.
set {ds3-addr} portnum
{"string"}
Set the DS3 port number PMDL string.
set {ds3-addr} gennum
{"string"}
Set the DS3 generation number PMDL
string.
set {ds3-addr} loopdetect
{off|on}
Set the detection/reaction to CSU
loopcodes.
Axxius 800 - Release 2.2
4-7
Configuration
Basic System Setup
Command
Description
set {ds3-addr} protect
{off|on}
Set port protection on the DS3.
set {ds3-addr} reversion
{off|on}
Set protection reversion on the DS3.
set {ds1-addr} threshold
{day|min15} {ccv|ces|cses|lcv
|les|pcv|pes|pses|sefs|uas)
Set default thresholds for a DS3.
set {ds3-addr} unit
{"string"}
Set the DS3 unit code PMDL string.
Establish a Static Channel Connection
Use the following commands to establish a static channel connection.
4-8
Command
Description
set {ds0-addr} type
{voice|data}
Set the channel type for the channel you
want to map. See set (ds0) command for
details.
set {ds0-addr} signal {emdw|
emi|emicpd|emw|gs|ls}
Set the signaling option for the channel you
want to map. See set (ds0) command for
details.
connect {slot:port}
{slot:port}
Connect the channels. See the show connect
command for details.
Axxius 800 - Release 2.2
Configuration
Basic System Setup
Setup of ADPCM
Command
Description
Connect T1 cable to port 1 of the ADPCM service card
set {adpcm_card-addr}
{none|map1|map2|map3}
Enable compressing by selecting Map type. Note:
none disables compression.
show (adpcm_card-addr}
Displays the status of the card, and the mapping.
connect 2:1:1-12 2:4:1-12
Set ADPCM cross-connects. The example
connects all 24 channels of the ADPCM to the 12
channels of the T1 (now compressed) on port 4.
This example is with map2
show connect {2:1)
Displays the connections made above.
Set Up a V.35 Port
Use the following commands to set up a V.35 port.
Command
Description
set {v35-addr} cts
{cd|high|low|rts}
Set the Clear to Send operation mode. See set
(v35) command for details.
set {v35-addr} data
{invert|normal}
Set the data mode. See set (v35) command for
details.
set {v35-addr} clock
{source|external}
Set the clock mode. See set (v35) command for
details.
set {v35-addr} speed
{56K|64K}
Set the speed. See set (v35) command for details.
set {v35-addr} txclkinv
{invert|normal}
Set the transmit clock inversion mode. See set
(v35) command for details.
set {v35-addr} rxclkinv
{invert|normal}
Set the receive clock inversion mode. See set
(v35) command for details.
Axxius 800 - Release 2.2
4-9
Configuration
Basic System Setup
Set Up a Single Channel POTS card
Use the following commands to set up a POTS card.
Command
Description
set {fxsPS-addr|fxsPSM-addr}
{ls|lsrb}
Set the signaling option for the port. See the
set (fxsPS or fxsPSM) command for details.
set {fxsPS-addr|fxsPSM-addr}
rxgain {n}
Set the receive gain/loss in dB. See the set
(fxsPS or fxsPSM) command for details.
set {fxsPS-addr|fxsPSM-addr}
txgain {n}
Set the transmit gain/loss in dB. See the set
(fxsPS or fxsPSM) command for details.
Change the IP Address of the DS0 Management Channel
Use the following commands to change the IP over DS0 Management Channel for the
Axxius 800.
Command
Description
set ipds0 down
Set the DS0 management channel down
set ipds0 ip address {ip-addr} Set the DS0 management channel IP address.
set ipds0 up
4-10
Set the DS0 management channel up.
Axxius 800 - Release 2.2
Configuration
Quick Configuration Reload
Quick Configuration Reload
The print config command can be used as a quick way to reload a configuration
into an Axxius unit, in the event that the configuration has been lost due to software
reload problems or operator error.
The download of the file generated by the print config command can be done by
direct connect to the RS-232 port or via Telnet, BUT the upload from the PC back to
the Axxius can only be done via direct RS-232 connection. The reason for this is that
there will not be an IP address in the Axxius because it is at the factory default at this
time.
The procedure described below is based on using Hyperterm.
Download Config File:
1. Connect to the unit using Hyperterm via the RS-232 port.
2. Type print config (do not hit [ENTER]).
3. Select Transfer/Capture Text... from the menu bar.
4. Name the file so that is can be accessed when needed.
Axxius 800 - Release 2.2
4-11
Configuration
Quick Configuration Reload
5. Select the [START] button, the window will close and the operator will be
returned to the Axxius command line.
6. Press [ENTER] to download. Axxius will generate an executable file of all
configurable commands and save it to the file location defined above.
7. The download is complete when the text has finished scrolling on the screen
and the Axxius ID prompt displays again.
Load Config File Back to Unit:
1. Select File/Properties
from the menu bar.
2. Select the Settings tab.
4-12
Axxius 800 - Release 2.2
Configuration
Quick Configuration Reload
3. Select the ASCII Setup button.
4. Set the Line delay to 50 milliseconds and the Character delay to 5
milliseconds.
5. Select the [OK] button back to the Main HyperTerminal screen.
6. Select Transfer/Send Text File... from the menu bar.
Hyperterm will now send the configuration to the Axxius exactly as it was saved
in the Download Config File process.
Axxius 800 - Release 2.2
4-13
Configuration
Setup of DS0 Management Channel
Setup of DS0 Management Channel
The DS0 Management Channel provides an alternative to the FDL link for
management information where FDL is unavailable. The Access Navigator and the
remote Axxius 800 will use IP packets to communicate management and control
information over the DS0 Management channel. A DS0 Channel will be used in the
remote Axxius 800 to send and receive the management IP packets.
The Navigator sends and receives the IP packets over its Ethernet connection while the
remote Axxius sends and receives the IP packets over a DS0 channel. A channelized
router takes the IP messages from the Ethernet to send them over DS0 channels (WAN)
and vice versa. The DS0s coming out of the router are on a single T1. It connects to the
Navigator, where the DS0s are cross-connected to the remote Axxius.
The following procedure will walk you through the basic setup of a DS0 Management
Channel.
Axxius
Axxius
with Router
192.168.201.101
IP packets carry Remote
Mgmt messages
(Axxius1)
192.168.202.1
One Management
T1 DS0 for each
Remote Axxius 800
T1 DS0 carrying
IP Packets
PC
192.168.201.102
Access
Navigator
EOD messages
carry ISDN
192.168.201.100
Axxius
(Axxius2)
192.168.202.2
Voice
Switch
4-14
Axxius 800 - Release 2.2
Configuration
Setup of DS0 Management Channel
Equipment Required
l Access Navigator (version 1.7)
l (1) Collocated Router
This example uses a Axxius 800 (version 1.0) with a Axxius TSR card
(version 1.0)
l Remote Axxius
(1-24) Axxius 800 (version 1.0)
l PC
l Cables
Ethernet
T1
Axxius
with Router
192.168.201.101
IP packets carry Remote
Mgmt messages
Axxius
(Axxius1)
192.168.202.1
One Management
T1 DS0 for each
Remote Axxius 800
T1 DS0 carrying
IP Packets
PC
192.168.201.102
Access
Navigator
192.168.201.100
Axxius
(Axxius2)
192.168.202.2
Basic Setup
Axxius 800 - Release 2.2
4-15
Configuration
Setup of DS0 Management Channel
The following is the Address and DS1 assignments used in this example. This will
configure 1 Access Navigator, one TSR and 24 remote Axxius units.
LAN addr
WAN addr
Navigator
DS1
Navigator mgmt
DS0 to Router
Axxius
Axxius DS0
to Navigator
Navigator
192.168.201.100
-
-
-
-
Router
192.168.201.101
-
32
-
-
PC
192.168.201.102
-
-
-
-
Axxius1
-
192.168.202.1
1
32:1
a:1:1
Axxius2
-
192.168.202.2
2
32:2
a:1:2
Axxius3
-
192.168.202.3
3
32:3
a:1:3
Axxius4
-
192.168.202.4
4
32:4
a:1:4
Axxius5
-
192.168.202.5
5
32:5
a:1:5
Axxius6
-
192.168.202.6
6
32:6
a:1:6
Axxius7
-
192.168.202.7
7
32:7
a:1:7
Axxius8
-
192.168.202.8
8
32:8
a:1:8
Axxius9
-
192.168.202.9
9
32:9
a:1:9
Axxius10
-
192.168.202.10
10
32:10
a:1:10
Axxius11
-
192.168.202.11
11
32:11
a:1:11
Axxius12
-
192.168.202.12
12
32:12
a:1:12
Axxius13
-
192.168.202.13
13
32:13
a:1:13
Axxius14
-
192.168.202.14
14
32:14
a:1:14
Axxius15
-
192.168.202.15
15
32:15
a:1:15
Axxius16
-
192.168.202.16
16
32:16
a:1:16
Axxius17
-
192.168.202.17
17
32:17
a:1:17
Axxius18
-
192.168.202.18
18
32:18
a:1:18
Axxius19
-
192.168.202.19
19
32:19
a:1:19
Axxius20
-
192.168.202.20
20
32:20
a:1:20
Axxius21
-
192.168.202.21
21
32:21
a:1:21
Axxius22
-
192.168.202.22
22
32:22
a:1:22
Axxius23
-
192.168.202.23
23
32:23
a:1:23
Axxius24
-
192.168.202.24
24
32:24
a:1:24
4-16
Axxius 800 - Release 2.2
Configuration
Setup of DS0 Management Channel
Set IP Configuration of PC
1. Set IP Address to 192.168.201.102
2. Set Gateway to 192.168.201.101 (Router LAN Address)
Configuring the Axxius Router
NOTE: The Remote Axxius WAN address MUST have a different subnet
than the Axxius Controller Ethernet address.
WAN Connections
The following WAN connections are made from a default condition with one (1)
TSR card installed set with factory defaults.
NOTE: An Axxius TSR is capable of managing 24 virtual WAN
connections through one of the ports of the Controller card. If support of
more than 24 Axxius units is required a Quad T1 and TSR card(s) can be
added; this however, can only be done on the collocated TSR, not on a
remote Axxius.
1. From the CLI execute the following command to connect one DS0 to each one
of the 24 WANs.
Command
Description
set local off
Sets the Axxius to be configured through CLI
set a:1 down
Sets port 1 of the Controller as Out-of-Service
disconnect a
Disconnects all connections to slot a (controller)
set a:1:1-24 type data
Sets all DS0s on the DS1-1 to data signaling type
connect a:1:1 1:1:1
Connects first DS0 of port 1 of the Controller to
port 1, WAN 1 of the Router in slot 1.
connect a:1:2 1:1:2
Connects second DS0 of port 1 of the Controller to port
1, WAN 2 of the Router in slot 1.
connect a:1:3 1:1:3
Up to 24 WAN connections (a:1:24 1:1:24)
Axxius 800 - Release 2.2
4-17
Configuration
Setup of DS0 Management Channel
Add and Enable all Remote Axxius Needed
Telnet into the TSR card
1. From the CLI execute a Telnet command to the TSR card.
Telnet {slot}
Example: telnet 1
The example will Telnet into the router located in slot 1.
2. Enter password (default is "admin") and select [ENTER].
3. Select Terminal Emulation (scroll with [TAB]) and select [ENTER].
Once you are in the router, the [TAB] key will move you through the menus
and the [SPACEBAR] will scroll you through selections in < >.
4-18
Axxius 800 - Release 2.2
Configuration
Setup of DS0 Management Channel
Configure Trunk Connections
1. Select Configuration < Profile Directory > -> from the Router Main
Menu and select [ENTER].
2. Select Router CARD <Setup - > from the Profile window and select
[ENTER].
3. Select Trunk <Configure - > and select [ENTER].
Axxius 800 - Release 2.2
4-19
Configuration
Setup of DS0 Management Channel
4. For all WAN port numbers already assigned a DS0 for management select
< Frame-Relay 1490 > as the WAN connections type.
5. Select the PVC Management as < Disabled >.
6. Select the [ESC] key to Exit and <Yes> to save changes. This will return
to the Trunk Configure window. For these configuration changes to take
effect, you must Reinitialize the Router.
Configure the Local Axxius Profile
1. Select Configuration < Profile Directory > -> from the Router Main
Menu and select [ENTER].
2. Select LocalUnit LAN <Setup - > and select [ENTER].
4-20
Axxius 800 - Release 2.2
Configuration
Setup of DS0 Management Channel
3. Set the following on this screen:
Select the IP Protocol Eth II (X), all others should not be selected.
Set the LAN Networks Updates for IP and IPX to < Neither >.
Set the LAN IP Address to 192.168.201.101 (Router IP Address) along
with the Subnet Mask of 255.255.255.0.
4. Select [ESC] to exit menu and <Yes> to save changes.
Create a Remote Axxius Profile for all Remotes
1. Select RemoteUnit WAN <Setup > from the Profile Directory main
window and select [ENTER].
Axxius 800 - Release 2.2
4-21
Configuration
Setup of DS0 Management Channel
2. Set the following on this screen:
Rename RemoteUnit (default name) to Axxius1.
Set WAN Networks Updates for IP to <Never>.
Set WAN IP: Numbered to <No>.
3. [TAB] to Setup: <Static/VPN Networks > (scroll to this selection if it is
not displayed).
Note: if the IP Protocol is set to <Bridge > this option will not be
available.
4. Set Setup Static: to <IP Networks> (scroll to this selection if it is not
displayed)
5. Select [CTRL A] to add a Static IP Address.
4-22
Axxius 800 - Release 2.2
Configuration
Setup of DS0 Management Channel
6. Set Device Name to Axxius1
Set the IP Address to 192.168.202.1 (Axxius1 WAN address)
Set the Subnet Mask to 255.255.255.255
Set the Metric to 1
7. Select [ESC] to exit and <Yes> to save changes.
8. Select Setup: <Trunk Port > and select [ENTER].
Axxius 800 - Release 2.2
4-23
Configuration
Setup of DS0 Management Channel
9. Select the following on this screen:
At the Select WAN Port Number: < None>, scroll from None to 1 (which
is the remote Axxius1).
Set DLCI to 16.
10. Select [ESC] to exit the Trunk Port configuration window.
11. Select [ESC] to exit and <Yes> to save changes.
4-24
Axxius 800 - Release 2.2
Configuration
Setup of DS0 Management Channel
Reinitialize the Router
1. Select Exit <Reinitialize > from the Router main window and select
[ENTER].
2. Select <YES> and select [ENTER] to Reinitialize the TSR Card. This will
save all the changes recently made to the Router.
Axxius 800 - Release 2.2
4-25
Configuration
Setup of DS0 Management Channel
Configuration of Remote Axxius
Note: The Ethernet cannot be connected to the Remote Axxius during the
setup of the DS0.
Use the following commands to setup the IP over DS0 Management Channel for
each Remote Axxius 800. connect to the Axxius1, use the following CLI
commands to setup the DS0 Management Channel.
Note: the following commands are assuming that the Remote Units are set to
factory defaults.
4-26
Command
Description
set local off
Sets the Axxius to be configured through CLI
set a:1 down
Sets the port 1 of the Controller as Out-of-Service
disconnect a
Disconnects all connections to slot a (controller),
assuming there are not any established cross-connects
that need to remain.
set a:1:1-24 type data
Sets all DS0s on port 1 of the Controller to data
signaling type
set ipds0 assign a:1:24
Assigns the DS0 as the IP management channel
set ipds0 ip address
192.168.202.1
255.255.255.0
Set the DS0 management channel IP address (the
Axxius1 WAN address is inserted here)
set ipds0 up
Set the DS0 management channel up
set snmp nms1
xxx.xxx.xxx.xxx
Sends alarms to server. Sends alarms to server.
xxx.xxx.xxx.xxx is the IP Address of the server.
show connect a:1
Displays connections to port 1 of the Controller
show ipds0
Will display the configurations of the DS0 management
channel
status ipds0
Will display the operational status (up/down) of the
DS0 management channel to the Navigator
Axxius 800 - Release 2.2
Configuration
Setup of DS0 Management Channel
Configuration of Access Navigator
Note: The Ethernet cannot be connected to the Remote Axxius during the
setup of the DS0.
The following setup, creates a path from the Axxius Router to the remote Axxius.
Note: the following commands are assuming that the Access Navigator is set
to factory defaults.
Command
Description
set ds1 1-32 down
Sets 1-32 Out-of-Service
set ethernet ip address
192.168.201.100
255.255.255.0
Sets the Ethernet IP address of the Navigator and it’s
subnet mask
set ip gateway
192.168.201.101
Sets the gateway (router address)
set ds1 32 type groom
Sets DS1 32 to groom
set ds0 32:1-24 type data
Sets DS0 32 1-24 to data signaling type
set ds1 1 remote device
mgmt caip 192.168.202.1
Sets DS1 1 as the Management Channel with the Router
(address listed)
set ds0 1:24 type data
Sets DS0 1-24 to data signaling type
connect 1:24 32:1
Connects DS1 1:DS0 24 to DS1 32, DS0 1
set ds1 32 up
Sets DS1 32 In Service
set ds1 1 up
Sets DS1 1 In Service
set snmp nms1
xxx.xxx.xxx.xxx
Sends alarms to server. xxx.xxx.xxx.xxx is the IP
Address of the server.
show ds1 1
Displays DS1 1 information
show ip
Displays IP Address information
show connect 1
Displays connections on DS1 1
status remote 1
Displays the status of the Management Channel
Axxius 800 - Release 2.2
4-27
Configuration
Setup of DS0 Management Channel
Testing the DS0 Management Channel
After the DS0 management channels has been setup with one Remote Axxius, test the
management channel.
1. PING 192.168.202.1 (Axxius1) from the Axxius Router.
2. PING 192.168.202.1 (Axxius1) from the Navigator.
3. PING 192.168.202.1 from the PC.
4. Telnet 192.168.202.1 from the PC to the Remote Axxius.
Once the Management Channel is working properly, add additional Remote units. Test
the DS0 Management Channel after each additional unit has been setup.
With the successful completion of the setup and test of the DS0 Management Channels,
the Ethernet may be reattached to the network.
4-28
Axxius 800 - Release 2.2
CHAPTER
CLI Commands
In this Chapter
n
Command Line Interface Help
n
CLI Commands
CLI Commands
Command Line Interface Help
During a CLI session, help is available at any time.
? or help
Type a ? (or "help" before a command) at any time for quick command information
> add ?
add ..................... Create users or profiles
{rtr_card-addr} ...... Create profile, object or service on a router
{rtr_lan-addr} ....... Create object or service on the router LAN
user ................. Create user with manager level access.
NOTE: The scrolling feature, will always scroll through the command/
options in alphabetical order.
[TAB] usage for word or command completion
Use [TAB] for command word completion:
> sh [TAB]
> show
Use [TAB] to view command levels:
> [TAB]
will scroll through the base commands
> aco [TAB]
> add [TAB]
> alarms [TAB]
> clear [TAB]
> connect [TAB]
> delete
... etc.
Use [TAB] to view command options, add a space after the base command with the use of
5-2
Axxius 800 - Release 2.2
CLI Commands
the [TAB] feature, scroll through all available options for this command:
> set [TAB]
will scroll through the set commands, with each <TAB>
> set alarms [TAB]
> set autoexit [TAB]
> set clock1
... etc.
If another space is placed after the command and [TAB] is pressed again, the next
command level will display (if any):
> set snmp [TAB] will scroll through all the set SNMP options
> set snmp contact [TAB]
> set snmp getcom [TAB]
> set snmp location [TAB]
> set snmp name
Axxius 800 - Release 2.2
... etc.
5-3
CLI Commands
CLI Commands
For maneuverability through these commands, all command names in blue or italics are
hyperlinked.
5-4
aco (Alarm Cut Off)
print
add
rename (router)
alarms
reset
clear
restore
connect
rtrping
delete
set
disconnect
show
exit
status
install
store
load
switch
log
telnet
ping
trace route
Axxius 800 - Release 2.2
CLI Commands
aco (Alarm Cut Off)
aco (Alarm Cut Off)
Use the aco command to activate the Alarm Cut Off, which opens the alarm relay contacts on
the back of the unit.
Syntax: aco
Example: aco
ACO LED
Off
Yellow
Normal mode. No alarms are being suppressed.
Alarm cutoff active. One or more active alarms suppressed.
To turn off ACO, all alarms must be cleared, or the operator can reset the controller, which will
set the ACO back to the default (off) state.
Axxius 800 - Release 2.2
5-5
CLI Commands
add
add
Use the add command to create users, interfaces, services or profiles.
See the following sections for detailed information on the following add commands
add (ds1) ais
add (router) dhcp server option
add (router) dns proxy
add (router) remote
add (router) snmp community
add (router) snmp trap
add (router) static dns host
add (router) uploaduser
add (router-lan) filter
add (router-lan) secondary ip address
add (router-lan) static
add (router-wan) firewall
add (router-wan) gre network
add (router-wan) nat bypass
add (router-wan) static
add user
5-6
Axxius 800 - Release 2.2
CLI Commands
add
add (ds1) ais
Use the add (ds1) ais command to add DS1s to a list for the AIS Forwarding feature. The DS1
enabled for AIS forwarding will be checked against the DS1s defined in the list.
Note: If no list is defined, AIS will go to all the DS1s cross-connected to that DS1.
Syntax: add {ds1-addr} ais {all|{ds1-addr1}, [ds1-addr2],
[ds1-addr3], [ds1-addr4]}
Example: add 1:1 ais 2:1, 3:1, 4:1, 5:1
{ds1-addr}
Enter the DS1 that has AIS enabled.
The Controller DS1 addresses are different on the DS3 and DS1 Controller, however the
DS1 address on the services cards does not change with Controller type (DS3 or DS1).
DS1 Address on a DS3 Controller in the form {slot:port:channel}
slot
A for the DS3 Controller card.
port
Port number, list or all.
ds1 channel Channel number, list or all.
DS1 Address on a DS1 Controller or service cards (with DS1 or DS3 controller) in
the form {slot:port}
slot
A for the DS1 Controller card, or 1-8 for service cards.
port
Port number, list or all.
all
Creates a AIS DS1 list all DS1s in the system to be configured to trigger sending AIS.
{ds1-addr1}, [ds1-addr2], [ds1-addr3], [ds1-addr4]
Creates a AIS DS1 list of up to 4 DS1s to be configured to trigger sending AIS.
Axxius 800 - Release 2.2
5-7
CLI Commands
add
add (router) dhcp server option
Use the add (router) dhcp server option command to add optional DHCP server
attributes that will be advertised every time a DHCP client discovery is initiated. This
provisioning takes effect immediately and can only be performed when the DHCP
server is enabled.
Syntax: add {rtr_card-addr} dhcp server option {tag} {setting}
Example: add 2 dhcp server option
add 2 dhcp server option
add 2 dhcp server option
add 2 dhcp server option
add 2 dhcp server option
add 2 dhcp server option
add 2 dhcp server option
20.0.0.1 100.150.3.97
19 false
13 byte1 200
160 byte2 3200
170 byte4 0xFEDCBA98
12 "www.carrieraccess.com"
150 192.168.0.33
150 192.168.0.33 10.40.1.1
{rtr_card-addr} - The slot number (1-8) that contains the Router (TSR) card.
{tag} - Range is 1-254. Options tags are unique, duplicate numbers will be rejected. To
change an option with the same tag, the old option must be deleted and then the new
option re-entered. 0 = off. Reserved numbers 6, 15, 44, 46, 47, 50, 51, 53, 54, 61.
{settings}
{true/false}
{byte1|byte2|byte4} {value}
{"string"}
{ip-addr} [ip-addr] [ip-addr]
[ip-addr]
5-8
Boolean uses true or false
byte1 = send value in 1 byte
byte2 = send value in 2 bytes
byte3 = send value in 4 bytes
value = any numeric value.
Unidentified with a maximum of 50
characters, enclosed in quotes.
IP address in the form xxx.xxx.xxx.xxx,
where xxx is a number from 0 to 255.
Axxius 800 - Release 2.2
CLI Commands
add
add (router) dns proxy
Use the add (router) dns proxy command to enable DNS proxy and add a remote DNS server
address to the specified Router card.
Syntax: add {rtr_card-addr} dns proxy {"domain-name"}
{ip-addr} {"profile-name"}
Example: add 2 dns proxy "Domain1" 192.168.100.245 "Texas"
Example will add a DNS proxy server "Domain1" with address
192.168.100.245 to the WAN named "Texas" on the TSR in slot 2.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"domain-name"}
The domain name for the external DNS server. Name must be enclosed in quotes, with a
maximum length of 42 characters.
{ip-addr}
The IP address of the external DNS server, in the form of xxx.xxx.xxx.xxx, where xxx is
between 0-255.
{"profile-name"}
The profile name for the Router interface that is used to reach this destination. Name must
be enclosed in quotes, with a maximum length of 11 characters.
add (router) remote
Use the add (router) remote command to add a remote WAN profile to the WAN profile table
on the specified Router card.
Syntax: add {rtr_card-addr} remote {"profile-name"}
Example: add 6 remote "Texas"
The example will add a remote WAN named "Texas" to the WAN profile table
for the TSR in slot 6.
{rtr_card-addr}
The slot number (1-8) of the Axxius chassis that contains the Router card.
{"profile-name"}
The name of the remote WAN profile to add with a maximum length of 11 characters. This
name must be enclosed in quotes.
Axxius 800 - Release 2.2
5-9
CLI Commands
add
add (router) snmp community
Use the add (router) snmp community command to add a SNMP community to an interface
on the specified Router card.
Syntax: add {rtr_card-addr} snmp community {read|write|both}
{"community-name"} {ip-addr}
Example: add 2 snmp community both "commune" 192.168.100.245
The example will allow the host 192.168.100.245 read/write access to the TSR
card SNMP agent using the community name "commune". The TSR is located
in slot 2.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{read|write|both}
both
read
write
Will set the community to be read/write
Will set the community to be read-only
Will set the community to be write-only
{"community-name"}
Name of the community to add with a maximum length of 10 characters. Must be enclosed
in quotes.
{ip-addr}
The IP address of the host that can access the SNMP agent via this community, in the form
of xxx.xxx.xxx.xxx, where xxx is between 0-255. The address "0.0.0.0" allows any host.
5-10
Axxius 800 - Release 2.2
CLI Commands
add
add (router) snmp trap
Use the add (router) snmp trap command to specify a destination to send SNMP trap
messages for the specified Router card.
Syntax: add {rtr_card-addr} snmp trap
{"community-name"} {ip-addr} {"profile-name"}
Example: add 3 snmp trap "commune" 192.168.100.245
"RemoteAxxius"
The example will add a trap destination of 192.168.100.245 on the interface
"RemoteAxxius" and use the community name "commune" in the messages.
The Router is located in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"community-name"}
The community name to use in each trap message, with a maximum of 10 characters.
{ip-addr}
The IP address of the destination trap to add, in the form of xxx.xxx.xxx.xxx, where xxx is
between 0-255.
{"profile-name"}
The profile name for the TSR interface that is used to reach this destination. Maximum of
11 characters and this name must be enclosed in quotes.
Axxius 800 - Release 2.2
5-11
CLI Commands
add
add (router) static dns host
Use the add (router) static dns host command to add a static DNS host record for resolving a
domain name to an IP address if the DNS server cannot provide the information. The DNS
resolver will first attempt to resolve the name by querying the configured DNS servers. If this
does not yield the information, the DNS resolver will consult this list of static entries. This
command will fail if the DNS resolver is not enabled.
Syntax: add {rtr_card-addr} static dns host
{ip-addr} {"domain-name"}
Example: add 2 dns host 192.168.100.245 "myhost.some.net"
Example will add a static DNS host record with address 192.168.100.245 and
domain named "myhost.some.net" on the TSR in slot 2.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{ip-addr}
The IP address of the host, in the form of xxx.xxx.xxx.xxx, where xxx is between 0-255.
{"domain-name"}
The domain name of the host. Name must be enclosed in quotes, with a maximum length
of 41 characters.
5-12
Axxius 800 - Release 2.2
CLI Commands
add
add (router) uploaduser
Use the add (router) uploaduser command to specify a host that is allowed to upload either
the configuration or software files to the specified Router card.
Syntax: add {rtr_card-addr} uploaduser {code|config|both}
{all|ip-addr} {"profile-name"}
Example: add 3 uploaduser code all "LosAngeles"
The example will allow any user to upload the code file from the TSR interface
named "LosAngeles". The TSR is located in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{both|code|config}
both
code
config
Will allow user to upload both the code file and the configuration file
from the Router
Will allow user to upload the code file from the Router
Will allow user to upload the configuration file from the Router
{all|ip-addr}
all
ip-addr
Will allow upload from anywhere
The IP address to allow upload boot from. In the form of
xxx.xxx.xxx.xxx, where xxx is between 0-255
{"profile-name"}
The name of the remote WAN or LAN profile that can be used for the upload. This name
must be enclosed in quotes.
Axxius 800 - Release 2.2
5-13
CLI Commands
add
add (router-lan) filter
Use the add (router-lan) filter commands to add filters to the specified LAN interface.
add (router-lan) filter address
Use the add (router-lan) filter address command to add an address filter to the table of
Layer 2 filters applied to the specified LAN interface.
Syntax: add {rtr_lan-addr} filter address {both|dest|source}
{mac-addr} {"filter-name"}
Example: add 2:1 filter address both 0x00e09700e9cd "Server1"
{tsr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
The slot number (1-8) that contains the Router card.
port
Port number of the Router.
"profile-name" The profile name for the Router interface. Name must be enclosed in
quotes, with a maximum length of 11 characters.
{both|dest|source}
both
dest
source
Filter by both source and destination
Filter by destination only
Filter by source only
{mac-addr}
The MAC address to add to the learned address table for the LAN, in the form a
6-octet HEX value, 0xxxxxxxxxxxx. Please note that the MAC address is preceeded by a
0x.
{"filter-name"}
A symbolic name given to identify a filter rule. This name must be enclosed in quotes, with
a maximum of 8 characters.
5-14
Axxius 800 - Release 2.2
CLI Commands
add
add (router-lan) filter custom
Use the add (router-lan) filter custom command to add a custom filter to the table of
Layer 2 filters applied to the specified LAN interface.
Syntax: add {rtr_lan-addr} filter custom {pkt-offset} {mask}
{match} {"filter-name"}
Example: add 2:1 filter custom 16 0xFFFF0000 0x45000000
"MyRule"
The example will add a custom layer-2 filter that will match all packets that
contain the hex value 4500 at the 16th octet past the MAC header.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
Slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{pkt-offset}
This field will designate where within a packet (past the MAC header) the system is to
begin looking for a matching character string. The offset value range is 0 to 60 bytes. To
create a filter for the data in the MAC header, use the address and Protocol filters. See charts
on the following page for Ethernet Frame and IP Packet formats.
Note: an offset of 12 will create a Source IP Address filter
an offset of 16 will create a Destination IP Address filter
{mask}
The 32-bit mask to indicate which bits to compare to the match value starting at the offset
position. The mask is entered as a 32-bit hexadecimal value (all Fs is exact match
FFFFFFFF).
{match}
The 32-bit match value that is used to match the incoming packet. The match value is
entered as a 32-bit hexadecimal value.
{"filter-name"}
A symbolic name given to identify a filter rule. This name must be enclosed in quotes, with
a maximum of 8 characters.
Axxius 800 - Release 2.2
5-15
CLI Commands
add
Ethernet Frame and IP Packet Format
Ethernet 802.3 (raw) Frame - Datalink Header
6 bytes
6 bytes
2 bytes
46 to 1500 bytes
Dest MAC Source MAC
Length
"FFF" followed by the data
4 bytes
FCS
------------Datalink (MAC) Header--------- ----Data and CRC (Frame Check Sequence)---
Version
(4 bits)
IP Packet Format
Type-of-Service
(8 bits)
Header Length
Total Length
(4 bits)
(16 bits)
Identification
Flags
Fragment Offset
(16 bits)
(3 bits)
(13 bits)
Time-to-Live (8 bits)
Protocol (8 bits)
Header Checksum (16 bits)
Source IP Address
Destination IP Address
IP Options (+ padding)
Data portion of Datagram
----------------------------------------------- 32 Bits -------------------------------------------------
5-16
Axxius 800 - Release 2.2
CLI Commands
add
add (router-lan) filter protocol
Use the add (router-lan) filter protocol command to add a protocol filter to the table of
Layer 2 filters applied to the specified LAN interface. Note that you only need to identify
either an Ethernet or IEEE value, but not both. The other should be entered as 0.
Syntax: add {rtr_lan-addr} filter protocol {ether-type}
{ieee-value} {"filter-name"}
Example: add 2:1 filter protocol 0x0807 0x0 "XNSrule"
The example will add a custom layer-2 filter that will match all XNS packets.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
Slot number (1-8) that contains the Router card.
port
Port number of the Router.
"profile-name" The profile name for the Router interface. Name must be enclosed in
quotes, with a maximum length of 11 characters.
{ether-type}
This assigned Ethernet value for this protocol. The ether-type is entered as a 16-bit
hexadecimal value. See Ethernet Protocol Types on page D-6 for protocol number and
descriptions.
{ieee-value}
The assigned IEEE value for this protocol. The IEEE value is the same as the SDAP and
SSAP values in a SNAP packet. The match value is entered as a 8-bit hexadecimal value.
{"filter-name"}
A symbolic name given to identify a filter rule. This name must be enclosed in quotes, with
a maximum of 8 characters.
Axxius 800 - Release 2.2
5-17
CLI Commands
add
add (router-lan) secondary ip address
Use the add (router-lan) secondary ip address command to add a secondary IP address and
subnet to the specified LAN interface. The Router will then be capable of routing between the
various subnets on the LAN interface or between any of the LAN subnets and any WAN subnet.
A maximum of 8 secondary IP addresses can be added to the LAN interface.
Syntax: add {rtr_lan-addr} secondary ip address
{ip-addr [mask]|ip-addr/bits}
Example: add 4:1 secondary ip address 192.168.1.1 255.255.255.0
The example will add a secondary IP address of 192.168.1.1 and a subnet mask
of 255.255.255.0.
To view the secondary IP addresses, use the show 4:1 command
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{ip-addr [mask]|ip-addr/bits}
ip-addr
mask
bits
5-18
The IP address of the Host to query, in the form of xxx.xxx.xxx.xxx,
where xxx is between 0-255.
The mask of the secondary IP address, in the form of
xxx.xxx.xxx.xxx, where xxx is between 0-255.
The subnet mask, specified as the number of ones bits in the mask
value. Range is between 1-32.
Axxius 800 - Release 2.2
CLI Commands
add
add (router-lan) static
Use the add (router-lan) static commands to add static elements on the specified LAN
interface.
add (router-lan) static ip address
Use the add (router-lan) static ip address command to add a static IP address to the table
of learned addresses on the specified LAN interface. This command is typically used in
bridging.
Syntax: add {tsr_lan-addr} static ip address {"addr-name"}
{ip-addr}
Example: add 3:1 static ip address "JDoe" 195.168.201.140
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
Slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{"addr-name"}
A symbolic name for this static ip address. This name must be enclosed in quotes, with a
maximum of 8 characters.
{ip-addr}
The IP address of the learned address table for the LAN, in the form of xxx.xxx.xxx.xxx,
where xxx is between 0-255.
Axxius 800 - Release 2.2
5-19
CLI Commands
add
add (router-lan) static ip network
Use the add (router-lan) static ip network command to add a static IP network (route) to
the specified LAN interface.
Syntax: add {rtr_lan-addr} static ip network {ip-addr} {mask}
{next-hop-ip-addr} [metric]
Example: add 3:1 static ip network 195.168.201.0 255.255.255.0
194.120.20.15 3
The example will add a static route to 192.168.201.0, with mask 255.255.255.0
and the next hop at 194.120.20.15 and a metric of 3 to the local LAN interface
on the Router card in slot 3.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
Slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{ip-addr}
The IP address of the static IP network to set, in the form of xxx.xxx.xxx.xxx, where xxx
is between 0-255.
{mask}
The mask of the static IP network, in the form of xxx.xxx.xxx.xxx, where xxx is between
0-255.
{next-hop-ip-addr}
The IP address of the next hop gateway for this route, in the form of xxx.xxx.xxx.xxx,
where xxx is between 0-255.
[metric]
Enter a numeric value indicating the distance from your local network to the destination
network. Although this value was originally measured by the number of gateways between
the two networks, the number may be modified, either higher or lower, to indicate a desired
priority. This field is only used on IP networks. Valid entries range from 1 to 15. (Please
note that a value of 1 usually indicates a direct network.)
5-20
Axxius 800 - Release 2.2
CLI Commands
add
add (router-lan) static ipx network
Use the add (router-lan) static ipx network command to add a static IPX network (route)
to the specified LAN interface.
Syntax: add {tsr_lan-addr} static ipx network {network} {hops}
{ticks} {next-hop-mac-addr}
Example: add 3:1 static ipx network 0x11 2 4 0x00e09700e9cd
The example will add a static IPX route to network 0x11, a hop count 2, a tick
count 4, a next hop Router at MAC address 00:e0:97:00:e9:cd.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
Slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{network}
The IPX network number in HEX (0x...). This number must be preceeded by 0x.
{hops}
The numeric value (of hops) indicating the distance from your Local (LAN) network to the
destination network.
{ticks}
The distance between two networks as measured in time increments (1/18th of a second).
Like hops, ticks may be used to designate primary and secondary routes to the same
network.
{next-hop-mac-addr}
The MAC address of the next hop Router, in the form a 6-octet HEX value separated by
colons, xxxxxxxxxxxx. This number must be preceeded by 0x.
Axxius 800 - Release 2.2
5-21
CLI Commands
add
add (router-lan) static mac address
Use the add (router-lan) static mac address command to add a static MAC address to the
table of learned addresses on the specified LAN interface. This command is typically used
in bridging.
Syntax: add {rtr_lan-addr} static mac address
{"network-name"} {mac-addr}
Example: add 3:1 static mac address "JDoe" 0x00e09700e9cd
The example will add a static MAC address, 00:e0:97:00:e9:cd named "JDoe",
to the tables for the LAN interface on the TSR card in slot 3.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
Slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{"network-name"}
A symbolic name given to identify this static MAC address. This name must be enclosed
in quotes, with a maximum of 7 characters.
{mac-addr}
The MAC address to add to the learned address table for the LAN, in the form a 6-octet
HEX value separated by colons, 0xxxxxxxxxxxxx. This number must be preceeded by 0x.
5-22
Axxius 800 - Release 2.2
CLI Commands
add
add (router-wan) firewall
Use the add (router-wan) firewall command to add a firewall rule to a WAN.
Syntax: add {rtr_card-addr} {"wan-name"} firewall
{rule-number} {drop|pass} {incoming|inout|outgoing}
{alarm|log|nolog} {service} {dest-ip-addr/bits} {srcip-addr/bits}
Example: add 3 "LosAngeles" firewall 1 pass incoming nolog http
203.1.21.17/32 0.0.0.0/0
The example will add a firewall rule that allows HTTP (TCP port 80) access
from any outside host to an inside web server at 203.1.21.17 to the TSR card in
slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{rule-number}
Firewall rules are processed in sequence until the first matching rule is found.
{drop|pass}
drop
pass
Do not allow the packet to be forwarded
Allow the packet to be forwarded
{incoming|inout|outgoing}
incoming
inout
outgoing
Matches packets for sessions originated from an outside host
Matches packets for sessions originated from either an inside or outside
host
Matches packets for sessions originated from an inside host
{alarm|log|nolog}
alarm
log
nolog
Axxius 800 - Release 2.2
Add an entry to alarm log for packets that match this rule
Add an entry to event log for packets that match this rule
Do not add an entry to the logs for packets that match this rule
5-23
CLI Commands
add
{service}
finger
ftp
gopher
http
icmp
nntp
ping
pop3
smtp
snmp
tcp
telnet
udp
wais
protocol
Display information about users
File Transfer Protocol
Document search and retrieval
World Wide Web
Internet Control Message Protocol
Network News Transfer
ICMP echo request/reply
Post Office Protocol Version 3
Simple Mail Transfer
Simple Network Management Protocol
Transmission Control Protocol
port number (0 - 65535) or range
User interface to remote unit
User Datagram Protocol
port number (0 - 65535) or range
Wide Area Information Services
Enter a protocol number. Note: for list of protocols and numbers see,
Protocol Number in Firewall Filters on page D-2.
{protocol-number}= number between 0-255
0 = any protocol
{dest-ip-addr/bits}
The destination IP Address and number of significant bits. The IP Address is in the form of
xxx.xxx.xxx.xxx, where xxx is between 0-255. The address "0.0.0.0/0" matches any
address.
dest-ip-addr
bits
5-24
Enter the IP Address of the local device or network that this rule will
affect. If you enter the address of a local device, this rule will affect
only the session establishments of the local device and the
destination address entered in the Remote IP Address/Network field,
below. The IP Address is in the form of xxx.xxx.xxx.xxx, where xxx
is between 0-255.
Use this field to identify the number of bits, from left to right that
will be used to match the IP Address field within the data packet.
Range is between 1-32.
Axxius 800 - Release 2.2
CLI Commands
add
{src-ip-addr/bits}
The destination IP address and number of significant bits. The address "0.0.0.0/0" matches
any address.
src-ip-addr
bits
Axxius 800 - Release 2.2
Enter the IP Address of the remote device or network that this rule
will affect. If you enter the address of a remote device, this rule will
affect only the session establishments of the remote device and the
destination address entered in the dest-ip-addr/bits command above.
The IP Address is in the form of xxx.xxx.xxx.xxx, where xxx is
between 0-255.
Use this field to identify the number of bits, from left to right that
will be used to match the IP Address field within the data packet.
Range is between 1-32.
5-25
CLI Commands
add
add (router-wan) gre network
Use the add (router-wan) gre network command to add a "by network" Generic Route
Encapsulation (GRE) tunnel to a WAN.
Syntax: add {rtr_card-addr} {"wan-name"} gre network
{ip-addr mask|ip-addr/bits} {metric}
{remote-ip-addr} {"tunnel-name"}
Example: add 3 "LosAngeles" gre network 10.0.0.0/8 3 2.2.2.2
"LATunnel"
The example will set the WAN interface named "LosAngeles" in slot 3 to pass
all packets destined for a host on subnet 10.0.0.0 through a GRE tunnel to
2.2.2.2.
Note: A set 3 "LosAngeles" gre ip by network command is required before
this command.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{ip-addr mask|ip-addr/bits}
ip-addr
mask
ip-addr
bits
The IP address and the subnet mask of the IP network to tunnel, each in the
form of xxx.xxx.xxx.xxx, where xxx is between 0-255.
The IP Address of the IP network to tunnel, in the form of xxx.xxx.xxx.xxx,
where xxx is between 0-255.
The subnet mask, specified as the number of ones bits in the mask value.
Range is between 1-32.
{metric}
Enter a numeric value indicating the distance from your local network to the destination
network. Valid entries range from 1 to 15.
{remote-ip-addr}
The IP address of the far end of this tunnel, in the form of xxx.xxx.xxx.xxx, where xxx is
between 0-255.
{"tunnel-name"}
A symbolic name for this tunnel. Maximum of 12 characters and must be enclosed in
quotes.
5-26
Axxius 800 - Release 2.2
CLI Commands
add
add (router-wan) nat bypass
Use the add (router-wan) nat bypass command to add subnets to the list of source addresses
that will not be subject to NAT translation when passing through a NAT enabled WAN
interface.
Syntax: add {rtr_card-addr} {"wan-name"} nat bypass
{ip-addr mask|ip-addr/bits}
Example:
The following example displays the configuration necessary to add two secondary IP
subnets to the LAN that do not get NAT translation performed on them when their packets
pass through the NAT on the WAN. In this example, packets leaving the "RemoteUnit"
WAN whose source IP address in the 10.0.0.0 subnet will be NAT translated to
211.103.55.1 before transmission. Packets leaving the "RemoteUnit" WAN whose source
IP address is in the 156.65.0.0 or 201.23.16.0 subnets will be transmitted unmodified.
set
add
add
set
set
add
add
1:1 ip address 10.0.0.1 255.0.0.0
1:1 secondary ip address 156.65.0.1 255.255.255.0
1:1 secondary ip address 201.23.16.1 255.255.255.0
1 "RemoteUnit" nat enable
1 "RemoteUnit" nat address 211.103.55.1 1
1 "RemoteUnit" nat bypass 156.65.0.0. 255.255.0.0
1 "RemoteUnit" nat bypass 201.23.16.0. 255.255.255.0
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{ip-addr mask|ip-addr/bits}
ip-addr mask
bits
Axxius 800 - Release 2.2
The IP address and subnet mask or host to bypass the NAT
translation, each in the form of xxx.xxx.xxx.xxx, where xxx is
between 0-255.
Use this field to identify the number of bits, from left to right that will
be used to match the IP Address field within the data packet. Range is
between 1-32.
5-27
CLI Commands
add
add (router-wan) static
Use the add (router-wan) static commands to add static elements on the specified WAN
interface.
add (router-wan) static ip address
Use the add (router-wan) static ip address command to add a static IP address to the table
of learned addresses on the specified WAN interface. This command is typically used in
bridging.
Syntax: add {rtr_card-addr} {"wan-name"} static ip address
{"name"} {ip-addr}
Example: add 3 "LosAngeles" static ip address "Pasadena"
195.168.201.140
The example will add a static IP address, 192.168.201.140, named "Pasadena"
to the tables for the WAN interface named "LosAngeles" on the TSR card in slot
3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{"name"}
A symbolic name to help remember the purpose of this entry. Maximum of 7 characters and
must be enclosed in quotes.
{ip-addr}
The IP address to add to the learned address table for the WAN, in the form of
xxx.xxx.xxx.xxx, where xxx is between 0-255.
5-28
Axxius 800 - Release 2.2
CLI Commands
add
add (router-wan) static ip network
Use the add (router-wan) static ip network command to add a static IP network (route)
to the specified WAN interface.
Syntax: add {rtr_card-addr} {"wan-name"} static ip network
{ip-addr} {mask} {metric}
Example: add 3 "LosAngeles" static ip network 195.168.201.0
255.255.255.0 3
The example will add a static route to 195.168.201.0, with mask 255.255.255.0
and a metric of 3 to the WAN interface named "LosAngeles" on the Router card
in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{ip-addr}
The IP address of the static IP network, in the form of xxx.xxx.xxx.xxx, where xxx is
between 0-255.
{mask}
The mask of the static IP network, in the form of xxx.xxx.xxx.xxx, where xxx is between
0-255.
{metric}
A numeric value indicating the distance from your local network to the destination network.
Valid entries range from 1 to 15. (Please note that a value of 1 usually indicates a direct
network).
Axxius 800 - Release 2.2
5-29
CLI Commands
add
add (router-wan) static ipx network
Use the add (router-wan) static ipx network command to add a static IPX network (route)
to the specified WAN interface.
Syntax: add {rtr_card-addr} {"wan-name"} static ipx network
{network} {hops} {ticks}
Example: add 3 "LosAngeles" static ipx network 0x11 2 4
The example will add a static IPX Router to network 0x11, with a hop count of
2 and a tick count of 4 to the WAN interface named "LosAngeles" on the Router
card in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{network}
The IPX network number in HEX (0x...)
{hops}
The numeric value (of hops) indicating the distance from your Local (LAN) network to the
destination network.
{ticks}
The distance between two networks as measured in time increments (1/18th of a second).
Like hops, ticks may be used to designate primary and secondary routes to the same
network. Although both the hops and ticks values are considered when determining routing
priority, for Novell networks, the tick value is considered first.
5-30
Axxius 800 - Release 2.2
CLI Commands
add
add (router-wan) static mac address
Use the add (router-wan) static mac address command to add a static MAC address to
the table of learned addresses on the specified WAN interface. This command is typically
used in bridging.
Syntax: add {rtr_card-addr} {"wan-name"} static mac address
{"name"} {mac-addr}
Example: add 3 "LosAngeles" static mac address "JDoe"
x000e09700e9cd
The example will add a static MAC address, 00:e0:97:00:e9:cd named "JDoe"
to the tables for the WAN interface named "LosAngeles" on the Router card in
slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{"name"}
A symbolic name to help remember the purpose of this entry. This name is a maximum of
7 characters and must be enclosed in quotes.
{mac-addr}
The MAC address to add to the learned address table for the LAN, in the form a
6-octet HEX value, 0xxxxxxxxxxxx. Please note that the MAC address is preceeded
by a 0x
Axxius 800 - Release 2.2
5-31
CLI Commands
add
add (router-wan) static nat address
Use the add (router-wan) static nat address command to add a static NAT bi-directional
mapping to the specified WAN interface. This command will fail if NAT is not enabled, if
the NAT address specified is in the NAT pool, or if the local or NAT address is not unique
within the complete group of static NAT mappings.
Syntax: add {rtr_card-addr} {"wan-name"} static nat address
{local-ip-addr} {nat-ip-addr}
Example: add 3 "LosAngeles" static nat address 10.0.0.5
34.56.102.222
The example will add a static NAT mapping between local IP address 10.0.0.5
to the public IP address 34.56.102.222 on the WAN interface named
"LosAngeles" on the Router card in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{local-ip-addr}
The IP address of the local IP host, in the form of xxx.xxx.xxx.xxx, where xxx is between
0-255.
{nat-ip-addr}
The NAT public IP address, in the form of xxx.xxx.xxx.xxx, where xxx is between 0-255.
add user
Use the add user command to create users with management level access (the highest level)
with no password. After adding a user, use the set user command to change the access level and
set the password for the new user. See also,set user, delete user.
Syntax: add user {"user-name"}
Example: add user "jsmith"
The example has added a new user named jsmith.
{"user-name"}
The user-name is the a user ID to add to the system. Text is a single word, with no blank
spaces and must be enclosed in quotes. Maximum of 10 characters.
5-32
Axxius 800 - Release 2.2
CLI Commands
alarms
alarms
Use the alarms command to display the active alarms. The report can be filtered by address,
category and/or severity (major, minor, alert). The alarms command alone, displays a full alarm
report.
Syntax: alarms [slot|slot:port|slot:port:channel] [category]
[severity]
Example: alarms a:1
Time
Date
Severity
00:00:10 01/01/2004 Major
Total=1
Description
A:1:1-DS1 Loss Of Frame
[slot|slot:port|slot:port:channel]
slot
port
channel
A for the controller card, or 1-8 for service cards.
Port number.
Channel number
[category]
ds1
env
equipment
fxs
tsr
v35
All DS1 facility alarms
Environmental Alarms
Equipment alarms not related to a DS1 interface
FXS facility alarms
TSR facility alarms
V.35 facility alarms
[severity]
alert
critical
info
major
minor
Axxius 800 - Release 2.2
Alert alarms (threshold crossing)
Critical alarms
Information alarms
Major alarms (service effecting)
Minor alarms (non-service affecting)
5-33
CLI Commands
clear
clear
User the clear command to clear logs, performance data and tables.
clear (ds1)
clear (ds3)
clear key
clear log
clear (ocudp) performance
clear (router) ip address table
clear (router) mac address table
clear (router) performance
5-34
Axxius 800 - Release 2.2
CLI Commands
clear
clear (ds1)
Use the clear (ds1) command to clear specified DS1 performance data.
Syntax: clear {ds1-addr} performance {setting}
Example: clear a:1 performance all
Clears all performance data on DS1 1 (port 1) on the DS1 Controller card.
{ds1-addr}
The Controller DS1 addresses are different on the DS3 and DS1 Controller, however the
DS1 address on the services cards does not change with Controller type (DS3 or DS1).
DS1 Address on a DS3 Controller in the form {slot:port:channel}
slot
A for the DS3 Controller card.
port
Port number, range or all.
ds1 channel Channel number, range or all.
DS1 Address on a DS1 Controller (DS1 mode) or service cards (with DS1 or DS3
controller) in the form {slot:port}
slot
A for the DS1 Controller card (DS1 mode), or 1-8 for service cards.
port
Port number, range or all.
{setting}
all
bes
css
dm
es
lcv
les
pcv
sefs
ses
uas
Axxius 800 - Release 2.2
Clear all performance data
Clear bes (bursty errored seconds) performance data.
Clear css (controlled slip seconds) performance data.
Clear dm (degraded minutes) performance data.
Clear es (errored seconds) performance data.
Clear lcv (line code violations) performance data.
Clear les (line errored seconds) performance data.
Clear pcv (path code violations) performance data.
Clear sefs (severely errored frame seconds) performance data.
Clear ses (severely errored seconds) performance data.
Clear uas (unavailable seconds) performance data.
5-35
CLI Commands
clear
clear (ds3)
Use the clear (ds3) command to clear specified DS3 performance data.
Note this command applies only when using a DS3 Controller card.
Syntax: clear {ds3-addr} performance {setting}
Example: clear a:1 performance all
Clears all performance data on DS3 1 (port 1) on the Controller card.
{ds3-addr}
DS3 address in the form {slot:port}.
slot
port
A for the controller card, or 1-8 for service cards.
Port number, range or all.
{setting}
all
ccv
ccvfe
ces
cesfe
cses
csesfe
lcv
les
pcv
pes
pses
sefs
uas
uasfe
5-36
Clear all performance data
Clear ccv (C-bit code violations) performance data.
Clear far end ccv (C-bit code violations) performance data.
Clear ces (C-bit errored seconds) performance data.
Clear far end ces (C-bit errored seconds) performance data.
Clear cses (C-bit severely errored seconds) performance data.
Clear far end cses (C-bit severely errored seconds) performance data.
Clear lcv (line code violations) performance data.
Clear les (line errored seconds) performance data.
Clear pcv (path code violations) performance data.
Clear pes (P-bit errored seconds) performance data.
Clear pses (P-bit severely errored seconds) performance data.
Clear sefs (severely errored frame seconds) performance data.
Clear uas (unavailable seconds) performance data.
Clear far end uas (unavailable seconds) performance data.
Axxius 800 - Release 2.2
CLI Commands
clear
clear key
Use the clear key command to remove a specific keyed feature. To acquire a feature key code,
contact Carrier Access Customer Service.
Syntax: clear [rtr_card-addr] key {"key-code"}
Example: clear key "q0B8yma2IsSL+1BarY0u"
[rtr_card-addr]
The slot number (1-8) that contains the Router card. This optional parameter is used for
router specific keyed features.
{"key-code"} - The key code is entered to enable the specific feature.
clear log
Use the clear log command to clear the event log. This will clear the log without asking for
confirmation.
Syntax: clear log
clear (ocudp) performance
Use the clear (ocudp) performance command to clear OCU-DP status counters.
Syntax: clear {ocudp-addr} performance
Example: clear 3:1 performance
Clears status counters on port 1 of the OCU-DP card in slot 3.
{ocudp-addr}
In the form {slot:port}.
slot
port
Axxius 800 - Release 2.2
Slot number (1-8) that contains the OCU-DP card.
Port number, range or all.
5-37
CLI Commands
clear
clear (router) ip address table
Use the clear (router) ip address table command to flush the learned entries from the IP
address table for the specified interface from the specified Router card.
Syntax: clear {rtr_card-addr} ip address table
["profile-name"]
Example: clear 2 ip address table
The example will clear all the entries on the IP address table.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
["profile-name"]
The name for the Router interface profile. This name must be enclosed in quotes, with a
maximum of 11 characters.
Note: the profile-name is optional, if not specified the tables for all interfaces will be
cleared.
clear (router) mac address table
Use the clear (router) mac address table command to flush the learned entries from the MAC
address table for the specified interface from the specified TSR card.
Syntax: clear {rtr_card-addr} mac address table
["profile-name"]
Example: clear 2 mac address table "LosAngeles"
The example will clear all the entries on the "LosAngeles" interface, MAC
address table.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
["profile-name"]
The name for the Router interface profile. This name must be enclosed in quotes, with a
maximum of 11 characters.
Note: the profile-name is optional, if not specified the tables for all interfaces will be
cleared.
5-38
Axxius 800 - Release 2.2
CLI Commands
clear
clear (router) performance
Use the clear (router) performance command to clear the runtime statistics that are displayed
by the status (router) performance command. This command takes effect immediately.
Syntax: clear {rtr_card-addr} performance {all|lan|wan}
Example: clear 4 performance all
The example will clear all of the runtime statistics on the router card in slot 4.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{all|lan|wan}
all
lan
wan
Axxius 800 - Release 2.2
Clear both LAN and WAN statistics
Clear the LAN statistics only.
Clear the WAN statistics only.
5-39
CLI Commands
connect
connect
Use the connect command to create two-way connections between any DS0 channels of the
service or controller cards.
Syntax: connect {slot:port|slot:port:channel}
{slot:port|slot:port:channel}
Use the disconnect command to delete connections.
Example: connect A:2:1-24 3:1
Connects all 24 channels on port address #2 (DS1) on the controller card
(slot A) to port address #1 V.35 in slot 3.
{slot:port|slot:port:channel}
slot
port
channel
A for the controller card, or 1-8 for service cards.
Port number or range.
Channel number or range, for T1 ports.
Channel Associated Signaling (CAS) Conversions
Cross-connects are done at a DS0 level. The following rules need to be kept in mind while
performing cross-connects for the voice cards.
FXO Analog
DS0
LS
GS
DPT
LSCPD DPT = Dial Pulse Termination
T1 DS0
5-40
EMDW = E&M Delayed Wink start
LS
Y
N
N
Y
EMI = E&M Immediate start
GS
N
Y
N
N
EMICPD = E&M Immediate Start with Calling
Party Disconnect
EMDW
N
N
N
N
EMW = E&M Wink start
EMI
N
N
Y
N
GS = Ground Start
EMICPD
N
N
N
N
LS = Loop Start
EMW
N
N
N
N
LSCPD = Loop Start Calling Party Disconnect
Axxius 800 - Release 2.2
CLI Commands
connect
connect (router-trunk) (t1)
Use the connect (router-trunk) (t1) command to create two-way connections between the
Router port trunk connections and any DS0 channels of the service card or Controller.
Syntax: connect {rtr_trunk-addr}
{slot:port|slot:port:channel}
Use the disconnect command to delete connections.
Note: addresses can also be in the following order:
connect {slot:port|slot:port:channel}
{rtr_trunk-addr}
Example: connect 5:1:1 a:2:1-12
Connects 12 channels on port address #2 (DS1) on the controller card (slot A)
to trunk 1 on the Router in slot 5.
{rtr_trunk-addr}
The Router trunk address is in the form {slot:port:trunk}.
slot
port
trunk
The slot number (1-8) that contains the Router card.
Port number of the TSR is 1. Note: there are 4 physical ports but only one
logical one used for addressing.
Trunk number for this port, 1-24.
{slot:port|slot:port:channel}
slot
port
channel
Axxius 800 - Release 2.2
A for the controller card, or 1-8 for service cards.
Port number or range (port must be a T1).
Channel number or range, for T1 ports.
5-41
CLI Commands
delete
delete
Use the delete command to remove users, interfaces, services or profiles.
See the following sections for detailed information on the following delete commands
delete (ds1) ais
delete (router) dhcp server option
delete (router) dns proxy
delete (router) remote
delete (router) snmp community
delete (router) snmp trap
delete (router) static dns host
delete (router) uploaduser
delete (router-lan) filter
delete (router-lan) secondary ip address
delete (router-lan) static
delete (router-wan) firewall
delete (router-wan) gre network
delete (router-wan) nat bypass
delete (router-wan) static
delete user
5-42
Axxius 800 - Release 2.2
CLI Commands
delete
delete (ds1) ais
Use the delete (ds1) ais command to delete DS1s from the AIS DS1 list. The DS1 that is AIS
enabled will be checked against the DS1s defined in the list.
Note: If no DS1s are defined, and AIS is enabled, the default will be all the DS1s in the
system. If all DS1s are removed from the lit the default of all the DS1s in the system will
be applied.
Syntax: delete {ds1-addr} ais {ds1-addr1}, [ds1-addr2],
[ds1-addr3], [ds1-addr4]
Example: delete 1:1 ais 2:1
{ds1-addr}
Enter the DS1 that has AIS enabled.
The Controller DS1 addresses are different on the DS3 and DS1 Controller, however the
DS1 address on the services cards does not change with Controller type (DS3 or DS1).
DS1 Address on a DS3 Controller in the form {slot:port:channel}
slot
A for the DS3 Controller card.
port
Port number, range or all.
ds1 channel Channel number, range or all.
DS1 Address on a DS1 Controller or service cards (with DS1 or DS3 controller) in
the form {slot:port}
slot
A for the DS1 Controller card, or 1-8 for service cards.
port
Port number, range or all.
{ds1-addr1}, [ds1-addr2], [ds1-addr3], [ds1-addr4]
Deletes a DS1 from the AIS DS1 list. The user can delete 1 to 4 DS1s from the list.
Axxius 800 - Release 2.2
5-43
CLI Commands
delete
delete (router) dhcp server option
Use the delete (router) dhcp server option command to delete optional DHCP server attributes
that will be advertised every time a DHCP client discovery is initiated. This provisioning takes
effect immediately and can only be performed when the DHCP server is enabled.
Syntax: delete {rtr_card-addr} dhcp server option {tag}
Example: add 2 dhcp server option 13
{rtr_card-addr}
The slot number (1-6) that contains the Router (IP, CMG or TSR) card.
{tag}
An existing tag to be removed. Use the show (router) dhcp command to see current options.
delete (router) dns proxy
Use the delete (router) dns proxy command to remove a remote DNS server address from the
specified Router card. If this command is directed to delete the only a DNS proxy server address
then DNS proxy is disabled.
Syntax: delete {rtr_card-addr} dns proxy {ip-addr}
Example: delete 2 dns proxy 192.168.100.245
The example will delete a DNS proxy server address of 192.168.100.245 from
the Router in slot 2.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{ip-addr}
The IP address of the external DNS server, in the form of xxx.xxx.xxx.xxx, where xxx is
between 0-255.
5-44
Axxius 800 - Release 2.2
CLI Commands
delete
delete (router) remote
Use the delete (router) remote command to delete a remote WAN profile from the WAN
profile table on the specified Router card.
Syntax: delete {rtr_card-addr} remote {"profile-name"}
Example: delete 6 remote "Texas"
The example will delete a remote WAN named "Texas" from the WAN profile
table for the Router in slot 6.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"profile-name"}
The name of the remote WAN profile to delete. This name must be enclosed in quotes, with
a maximum of 12 characters.
delete (router) snmp community
Use the delete (router) snmp community command to delete an SNMP community entry on
the specified Router card.
Syntax: delete {rtr_card-addr} snmp community
{"community-name"} {ip-addr}
Example: delete 2 snmp community "commune" 192.168.100.245
The example will delete the previously added SNMP community named
"commune" from the TSR in slot 2.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"community-name"}
The name of an existing community with a maximum of 12 characters, enclosed in quotes.
{ip-addr}
The IP address of the host that can access the SNMP agent via this community, in the form
of xxx.xxx.xxx.xxx, where xxx is between 0-255. The address "0.0.0.0" allows any host.
Axxius 800 - Release 2.2
5-45
CLI Commands
delete
delete (router) snmp trap
Use the delete (router) snmp trap command to delete a trap destination from the specified
Router card.
Syntax: delete {rtr_card-addr} snmp trap
{"community-name"} {ip-addr}
Example: delete 2 snmp trap "commune" 192.168.100.245
The example will delete the previously added SNMP community named
"commune" from the Router in slot 2.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"community-name"}
The name of an existing community. This name must be enclosed in quotes, with a
maximum of 12 characters.
{ip-addr}
The IP address of the destination trap to delete, in the form of xxx.xxx.xxx.xxx, where xxx
is between 0-255.
delete (router) static dns host
Use the delete (router) static dns host command to delete a static DNS host record.
Syntax: delete {rtr_card-addr} static dns host
{ip-addr} {"domain-name"}
Example: delete 2 dns host 192.168.100.245 "myhost.some.net"
Example will delete a DNS host entry with address 192.168.100.245 and
domain named "myhost.come.net" on the Router in slot 2.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{ip-addr}
The IP address of the host, in the form of xxx.xxx.xxx.xxx, where xxx is between 0-255.
{"domain-name"}
The domain name of the host with a maximum length of 41 characters, enclosed in quotes.
5-46
Axxius 800 - Release 2.2
CLI Commands
delete
delete (router) uploaduser
Use the delete (router) uploaduser command to remove an existing host that is allowed to
upload either the configuration or software files to the specified Router card.
Syntax: delete {rtr_card-addr} uploaduser
{all|ip-addr} {"profile-name"}
Example: delete 3 uploaduser "LosAngeles"
The example will remove any user for upload of a code file from the TSR
interface named "LosAngeles". The TSR is located in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{all|ip-addr}
all
ip-addr
Will delete all upload users.
The IP address of the host, in the form of xxx.xxx.xxx.xxx, where xxx is
between 0-255.
{"profile-name"}
The name of the remote WAN or LAN profile specified in the entry to be removed. This
name must be enclosed in quotes.
Axxius 800 - Release 2.2
5-47
CLI Commands
delete
delete (router-lan) filter
Use the delete (router-lan) filter command to delete a single filter rule from the table of Layer
2 filters applied to the specified LAN interface.
Syntax: delete {rtr_lan-addr} filter
{address|custom|protocol|all} {"filter-name"}
Example: delete 2:1 filter address "Server1"
This example will delete a previously created address filter names "Server1".
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
Slot number (1-8) that contains the Router card
Port number of the Router.
The profile name for the Router interface. Name must be enclosed in
quotes, with a maximum length of 11 characters.
{address|custom|protocol|all}
address
custom
protocol
all
A previously created address filter
A previously created custom filter
A previously created protocol filter
All filter rules. this options does not require a filter-name to follow
{"filter-name"}
A symbolic name given to identify a filter rule. This name must be enclosed in quotes, with
a maximum of 8 characters.
5-48
Axxius 800 - Release 2.2
CLI Commands
delete
delete (router-lan) secondary ip address
Use the delete (router-lan) secondary ip address command to delete a secondary IP address
and subnet to the specified LAN interface.
Syntax: delete {rtr_lan-addr} secondary ip address
{ip-addr [mask]|ip-addr/bits}
Example: delete 4:1 secondary ip address 192.168.1.1
The example will delete a secondary IP address of 192.168.1.1.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
The slot number (1-8) that contains the Router card
port
Port number of the Router.
"profile-name" The profile name for the Router interface. Name must be enclosed in
quotes, with a maximum length of 11 characters
{ip-addr [mask]|ip-addr/bits}
ip-addr
mask
bits
Axxius 800 - Release 2.2
The IP address of a current secondary IP address, in the form of
xxx.xxx.xxx.xxx, where xxx is between 0-255.
The mask of the secondary IP address, in the form of
xxx.xxx.xxx.xxx, where xxx is between 0-255
The subnet mask, specified as the number of ones bits in the mask
value. Range is between 1-32.
5-49
CLI Commands
delete
delete (router-lan) static
Use the delete (router-lan) static commands to delete static elements from the specified LAN
interface.
delete (router-lan) static ip address
Use the delete (router-lan) static ip address command to delete a static IP address entry
from the specified LAN interface.
Syntax: add {rtr_lan-addr} static ip address {ip-addr}
Example: add 3:1 static ip address 195.168.201.140
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
Slot number (1-8) that contains the Router card
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters
{ip-addr}
The IP address of the learned address table for the LAN, in the form of xxx.xxx.xxx.xxx,
where xxx is between 0-255.
5-50
Axxius 800 - Release 2.2
CLI Commands
delete
delete (router-lan) static ip network
Use the delete (router-lan) static ip network command to delete a static IP network from
the specified LAN interface.
Syntax: delete {rtr_lan-addr} static ip network {ip-addr}
{mask} {next-hop-ip-addr}
Example: delete 3:1 static ip network 195.168.201.0
255.255.255.0 194.120.20.15
The example will delete the existing static IP network from the LAN interface
of the Router card in slot 3.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
Slot number (1-8) that contains the Router card
port
Port number of the Router.
"profile-name" The profile name for the Router interface. Name must be enclosed in
quotes, with a maximum length of 11 characters
{"profile-name"}
The IP address of the static IP network, in the form of xxx.xxx.xxx.xxx, where xxx is
between 0-255.
{ip-addr}
The IP address of the static IP network, in the form of xxx.xxx.xxx.xxx, where xxx is
between 0-255.
{mask}
The mask of the static IP network, in the form of xxx.xxx.xxx.xxx, where xxx is between
0-255.
{next-hop-ip-addr}
The IP address of the next hop gateway for this route, in the form of xxx.xxx.xxx.xxx,
where xxx is between 0-255.
Axxius 800 - Release 2.2
5-51
CLI Commands
delete
delete (router-lan) static ipx network
Use the delete (router-lan) static ipx network command to delete a static IPX network
(route) to the specified LAN interface.
Syntax: delete {rtr_lan-addr} static ipx network {network}
{next-hop-ip-addr}
Example: delete 3:1 static ipx network 0x11 0x00e09700e9cd
The example will delete a static IPX route to network 0x11, using a next hop
Router at MAC address 00:e0:97:00:e9:cd, from the LAN interface on the
Router card in slot 3.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
Slot number (1-8) that contains the Router card.
port
Port number of the Router.
"profile-name" The profile name for the Router interface. Name must be enclosed in
quotes, with a maximum length of 11 characters.
{network}
The IPX network number in HEX (0x...).
{next-hop-ip-addr}
The MAC address of the next hop Router, in the form a 6-octet HEX value, in the form
0xxxxxxxxxxxxx. Please note the address is preceeded by 0x.
5-52
Axxius 800 - Release 2.2
CLI Commands
delete
delete (router-lan) static mac address
Use the delete (router-lan) static mac address command to delete a static MAC address
entry to the specified LAN interface.
Syntax: delete {rtr_lan-addr} static mac address {mac-addr}
Example: delete 3:1 static mac address 0x00e09700e9cd
The example will delete a static MAC address, 00:e0:97:00:e9:cd, from the
LAN interface of the Router card in slot 5.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
The slot number (1-8) that contains the Router card
port
Port number of the Router.
"profile-name" The profile name for the Router interface. Name must be enclosed in
quotes, with a maximum length of 11 characters
{mac-addr}
The MAC address to add to the learned address table for the LAN, in the form a
6-octet HEX value, 0xxxxxxxxxxxx. Note that the MAC address is preceeded by a 0x.
delete (router-wan) firewall
Use the delete (router-wan) firewall command to delete a firewall rule from a WAN.
Syntax: delete {rtr_card-addr} {"wan-name"} firewall
{all|rule-number}
Example: delete 3 "LosAngeles" firewall all
The example will remove all firewalls rules on the Router in slot 3, for the
profile "LosAngeles".
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{all|rule-number}
all
rule-number
Axxius 800 - Release 2.2
Delete all firewall rules on this WAN
The specific firewall rule to delete
5-53
CLI Commands
delete
delete (router-wan) gre network
Use the delete (router-wan) gre network command to delete a "by network" GRE tunnel to a
WAN.
Syntax: delete {rtr_card-addr} {"wan-name"} gre network
{ip-addr mask|ip-addr/bits}
Example: delete 3 "LosAngeles" gre network 10.0.0.0/8
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{ip-addr mask|ip-addr/bits}
ip-addr mask
ip-addr
bits
The IP address and the subnet mask of the IP network to tunnel, each
in the form of xxx.xxx.xxx.xxx, where xxx is between 0-255.
The IP Address of the IP network to tunnel, in the form of
xxx.xxx.xxx.xxx, where xxx is between 0-255.
The subnet mask, specified as the number of ones bits in the mask
value. Range is between 1-32.
delete (router-wan) nat bypass
Use the delete (router-wan) nat bypass command to delete an IP subnet or host from the list
of the source addresses that will not be subject to NAT Translation when passing through a NAT
enabled WAN interface.
Syntax: delete {rtr_card-addr} {"wan-name"} nat bypass
{ip-addr}
Example: delete 1 "RemoteUnit" nat bypass 156.65.0.0
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{ip-addr}
IP address or host to delete, in the form of xxx.xxx.xxx.xxx, where xxx is between 0-255.
5-54
Axxius 800 - Release 2.2
CLI Commands
delete
delete (router-wan) static
Use the delete (router-wan) static commands to delete a static element from the WAN
interface.
delete (router-wan) static ip address
Use the delete (router-wan) static ip address command to delete a static IP address on the
specified WAN interface.
Syntax: delete {rtr_card-addr} {"wan-name"} static ip address
{ip-addr}
Example: delete 3 "LosAngeles" static ip address
195.168.201.140
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{ip-addr}
The IP address to delete from the WAN, in the form of xxx.xxx.xxx.xxx, where xxx is
between 0-255.
Axxius 800 - Release 2.2
5-55
CLI Commands
delete
delete (router-wan) static ip network
Use the delete (router-wan) static ip network command to delete a static IP network from
the specified WAN interface.
Syntax: delete {rtr_card-addr} {"wan-name"} static ip network
{ip-addr} {mask}
Example: delete 3 "LosAngeles" static ip network 195.168.201.0
255.255.255.0
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{ip-addr}
IP address of the static IP network, in the form of xxx.xxx.xxx.xxx, where xxx is between
0-255.
{mask}
Mask of the static IP network, in the form of xxx.xxx.xxx.xxx, where xxx is between 0-255.
delete (router-wan) static ipx network
Use the delete (router-wan) static ipx network command to delete a static IPX network
(route) to the specified WAN interface.
Syntax: delete {rtr_card-addr} {"wan-name"} static ipx network
{network}
Example: delete 3 "LosAngeles" static ipx network 0x11
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{network}
The IPX network number in HEX (0x...)
5-56
Axxius 800 - Release 2.2
CLI Commands
delete
delete (router-wan) static mac address
Use the delete (router-wan) static mac address command to delete a static MAC address
entry from the specified WAN interface.
Syntax: delete {rtr_card-addr} {"wan-name"} static mac address
{mac-addr}
Example: delete 3 "LosAngeles" static mac address
0x00e09700e9cd
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{mac-addr}
The MAC address to add to the learned address table for the LAN, in the form
0xxxxxxxxxxxxx. Please note the address is preceeded by 0x.
delete (router-wan) static nat address
Use the delete (router-wan) static nat address command to delete a static NAT mapping
from the specified WAN interface.
Syntax: delete {rtr_card-addr} {"wan-name"} static nat address
{local-ip-addr} {nat-ip-addr}
Example: delete 3 "LosAngeles" static nat address 10.0.0.5
34.56.102.222
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{local-ip-addr}
IP address of the local IP host, in the form of xxx.xxx.xxx.xxx, where xxx is between 0-255.
{nat-ip-addr}
The NAT public IP address, in the form of xxx.xxx.xxx.xxx, where xxx is between 0-255.
Axxius 800 - Release 2.2
5-57
CLI Commands
disconnect
delete user
The delete user command will remover a user created by the add user command.
Syntax: delete user {"user-name"}
Example: delete user "jsmith"
{"user-name"}
The user-name is an existing user ID in the system. This name must be enclosed in quotes.
disconnect
disconnect
Remove a connection created using the connect command.
Syntax: disconnect
{slot|slot:port|slot:port:channel|slot:port:trunk}
Example: disconnect A:2:1-24 3:1
Disconnects all 24 channels on port address #2 (DS1) on the controller card (slot
A) to port address #1 V.35 in slot 3.
NOTE: The operator can remove connections for all of a slot {slot}, a port
within a slot {slot:port}, or for specific channel {slot:port:channel}
{slot|slot:port|slot:port:channel|slot:port:trunk}
slot
port
channel
trunk
5-58
A for the controller card, or 1-8 for service cards.
Port number or range.
Channel number or range, for T1 ports.
Trunk number for this port, 1-24.
Axxius 800 - Release 2.2
CLI Commands
exit
exit
Use the exit command to log out of the Command Line Interface (CLI).
Syntax: exit
Example: > exit
Logging out of Carrier Access - Axxius Product Line
install
install (slot) router
The Axxius 800 Controller card automatically creates a backup of the configuration of any
router cards in their respective slot. If a router card is removed and replaced with a another card
(of the same type) the backup of the configuration from the first occupying card is loaded onto
the replacing card. This command will stop this function and the replacing router card will retain
its configuration.
Syntax: install {number} {cmg|router|tsr}
Example: install 5 router
{number}
The slot number (1-8) of the card to download the software file to.
{cmg|router|tsr}
The router type. Note: Only the TSR is supported in the this release.
To replace a router card in slot 5 and retain its loaded configuration file:
1. Remove current router card in slot 5 of the Axxius system.
2. With the CLI command enter:
> install 5 router
ok
3. When an "ok" is displayed the replacement router card may be inserted into
slot 5.
Axxius 800 - Release 2.2
5-59
CLI Commands
load
load
WARNING! BEFORE LOADING A DOWN-LEVEL OF ROUTER CODE TO AN
ADIT, SAVE THE CONFIGURATION TO A FILE. CONFIGURATION MAY BE RESET TO
THE DEFAULT SETTING AND CURRENT CONFIGURATION LOST.
load tftp
The load tftp command will download software via TFTP to the Controller or to the TSR card.
Note: A TFTP server must be running on the host system for this command to be successful.
Syntax: load {ctrlr-id|number} tftp {ip-addr} {"file-name"}
Example: load a1 tftp 192.102.3.168 "axxius1_0_all.mgm"
The example will download the Controller software file "axxius1_0_all.mgm"
to the Controller in slot 1, via TFTP.
Example: load 5 tftp 172.26.100.25 "tsr1_20.mgm"
The example will download the Router software file "tsr1_20.mgm" to a TSR
card in slot 5 via TFTP.
Example: load 5 tftp 172.26.100.25 "config.txt"
The load tftp command is modified to add special processing when a filename
ends with "txt". In this case, the .txt file is handled as an ASCII file containing
CLI commands to configure the Axxius 800.
{ctrlr_id|number}
ctrlr_id
rtr_card-addr
Controller identifier to download the software to.
A1, A2 All, Active or Standby. Note: always load to the standby
controller, in a redundant system, reset and switch controllers,
then load again to the new standby controller.
Slot number (1-8) of a Router card to load the software file to.
{ip-addr}
The host IP address in the form of xxx.xxx.xxx.xxx, where xxx is a number from 0-255. If
not supplied the host IP address from the database will be used.
{"file-name"}
The software file to load including path. Must be enclosed with quotes.
The file-type of the downloading files must be .mgm, or .txt.
5-60
Axxius 800 - Release 2.2
CLI Commands
load
load xmodem
Use the load xmodem command to download software via Xmodem. This command is only
available with an RS-232 connection. If you are using Telnet, see load tftp command.
Syntax: load {ctrlr-id} xmodem
Example: load a2 xmodem
The example initiates an modem transfer to the Controller card in slot A2.
Do you really want to do this?
Enter Y at the prompt to continue, or N to cancel the download.
Y - the system will prompt you to select the appropriate local file. With the file selected, the
system will complete the download, reboot, and run the installation for flash upgrade. Screen
example following.
**** System Boot ****
Copyright 1999,2000 Carrier Access Corporation.
XMODEM transfer started
Validating image(fast)..........................SUCCEEDED!
Erasing FLASH:..........................Finished Erasing FLASH!
Erasing FLASH:..........................Finished Erasing FLASH!
Programming Flash..........................SUCCEEDED!
In 5 seconds the system will boot from Flash
Press any key to stop boot . 5 . 4 . 3 . 2 . 1 . 0
Looking for valid application image in Flash...
Executing application image from Flash
Attached TCP/IP interface to cpm unit 0
Attaching interface lo0...done
Axxius startup
{ctrlr_id}
ctrlr_id
Axxius 800 - Release 2.2
Controller identifier to download the software to.
A1, A2 All, Active or Standby
5-61
CLI Commands
log
log
log
Displays the event log. Where the optional [slot:port:channel], [category], and [severity] are
variables used to narrow down the log displayed. The log command without any options
displays a full log.
Syntax: log [slot|slot:port] [category] [severity]
Example: log a:1
Time
Date
Severity
00:00:08 01/01/2002 Major
00:00:08 01/01/2002 Major
00:00:08 01/01/2002 Major
Total=3
Description
A:1:28-DS1 Loss Of Frame
A:1:27-DS1 Loss Of Frame
A:1:26-DS1 Loss Of Frame
[slot|slot:port|slot:port:channel]
slot
port
channel
A for the controller card, or 1-8 for service cards
Port number (not a range)
Channel number or range
[category]
slot
port
channel
slot
port
channel
slot
port
A for the controller card, or 1-8 for service cards
Port number (not a range)
Channel number or range
A for the controller card, or 1-8 for service cards
Port number (not a range)
Channel number or range
A for the controller card, or 1-8 for service cards
Port number (not a range)
[severity]
alert
critical
info
major
minor
5-62
Alert events (threshold crossing)
Critical events
Information events
Major events (service effecting)
Minor events (non-service affecting)
Axxius 800 - Release 2.2
CLI Commands
ping
ping
ping
Use the ping command to perform a ping test from the Controller and report the result. If the
host is reachable, each individual response will be displayed.
Syntax: ping {ip-addr} [count] [length]
Example: ping 192.168.3.196 7 5000
Pinging 192.168.3.196 with 5000 bytes of data:
Reply
Reply
Reply
Reply
Reply
Reply
Reply
from
from
from
from
from
from
from
192.168.3.196:
192.168.3.196:
192.168.3.196:
192.168.3.196:
192.168.3.196:
192.168.3.196:
192.168.3.196:
bytes=5000
bytes=5000
bytes=5000
bytes=5000
bytes=5000
bytes=5000
bytes=5000
time=90ms
time=144ms
time=186ms
time=90ms
time=90ms
time=90ms
time=90ms
> ping 192.168.10.196 7 5000
PING 192.168.10.196: 5000 data bytes
no answer from 192.168.10.196
{ip-addr}
The host IP address of the device to query, in the form of xxx.xxx.xxx.xxx, where xxx is a
number from 0-255.
[count]
This optional parameter sets the number of pings to send. Range is 1 to 32, default is 5.
[length]
This optional parameter sets the number of bytes to send in the ICMP echo request payload.
Range is 0 to 8000, default is 56.
Axxius 800 - Release 2.2
5-63
CLI Commands
print
print
Use the print command to display the help information or print the configuration file.
Syntax: print {config|help}
print config
Print the configuration file for the Axxius 800. The operator may then save this to a text file,
which can be sent to another Axxius to automatically configure the system with the original
Axxius 800 configuration.
Syntax: print config [rtr_card-addr]
[rtr_card-addr] - The slot number (1-8) that contains the Router card.
Example: print config 5
This example would produce a configuration file of the Router in slot 5.
Axxius> print config 5
set verification off
-set 5 password view
{password} is manual
-set 5 password config {password} is manual
-set 5 password admin {password} is manual
-set 5 enhanced security enable
is manual
-set 5 password security {password} is manual
delete 5 remote "RemoteUnit"
set 5 stp enable
rename 5 "LocalUnit" "LocalAxxius"
set 5:1 ip address 192.168.3.195 255.255.255.0
add 5:1 secondary ip address 192.168.3.194 255.255.255.0
set 5:1 up
set 5:1 collision threshold high 500
add 5 remote "RemoteUnit"
reset 5
Example: print config
This example would produce a configuration file of the Controller.
1.
While in a Telnet session to an Adit 600 select Terminal/Start Logging.
2.
Name the file.
3.
Type the CLI command print config.
4.
Select Terminal/Stop Logging.
See Load Controller Configuration on page 18-10 for instructions to reload configuration to
Controller card.
5-64
Axxius 800 - Release 2.2
CLI Commands
rename (router)
print help
Print the complete help file to the screen.
Syntax: print help
Example: print help
This example would print the entire help text, which can be scrolled though with
Enter or Spacebar.
rename (router)
Use the rename (router) command to change the name of a local LAN or remote WAN profile
on the specified Router card. Profile names cannot contain spaces and must be unique on a
particular TSR card.
Syntax: rename {rtr_card-addr} {"old-profile-name"}
{"new-profile-name"}
Example: rename 6 "Chicago" "Milwaukee"
This example will change the name of the WAN profile from "Chicago" to
"Milwaukee", for the Router in slot 6.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"old-profile-name"}
The current LAN or WAN profile name. This name must be enclosed in quotes.
{"new-profile-name"}
The new profile name of a LAN or WAN profile. This name has a maximum length of 11
characters, and must be enclosed in quotes.
Axxius 800 - Release 2.2
5-65
CLI Commands
reset
reset
reset (controller)
Use the reset (controller) command to reboot the system. Reset alone will reboot the entire
system.
Syntax: reset [ctrlr-addr|active|standby]
Example: reset a1
Will reset the controller in the controller slot 1.
Do you really want to reset (y/n)? y
**** System Boot ****
Copyright 1999,2000 Carrier Access Corporation.
{ctrlr_card-addr|active|standby}
ctrlr_card-addr Resets the Controller in the defined slot number (a1 or a2)
active
Resets the active Controller
standby
Resets the standby Controller
WARNING!
THE COMMANDS reset AND reset active ARE SERVICE AFFECTING
COMMANDS.
reset (router)
Use the reset (router) command to reboot the Router. All new configuration since the last
reset will be in use.
Syntax: reset {rtr_card-addr}
Example: reset 1
The example will reset the Router card in slot 1.
Do you really want to do this ?
OK
y
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
5-66
Axxius 800 - Release 2.2
CLI Commands
restore
reset (router) coldboot
Use the reset (router) coldboot command to reboot the Router. This will reboot including a
power cycle to the Router card.
Syntax: reset {rtr_card-addr} coldboot
Example: > reset 2 coldboot
OK
The example will coldboot the Router card in slot 2.
{rtr_card-addr}
The slot number (1-8) that contains the Router (TSR) card.
restore
Use the restore command to restore system properties.
Note: to restore Router defaults see set (router) default.
restore defaults
Loads factory defaults for all settings. This command will not take effect until the system is
rebooted using the reset command.
Syntax: restore defaults
Example: restore defaults
For the restore default changes to take effect send a reset command.
Further configuration changes made before a reset will be lost.
Axxius 800 - Release 2.2
5-67
CLI Commands
rtrping
rtrping
Use the rtrping command to request that the Router perform a ping test and report the result.
Syntax: rtrping {rtr_card-addr} {dest-ip-addr|"domain-name"}
[count] [count length] [count length source-ip-addr]
Example: rtrping 4 192.168.100.97
> rtrping 4 192.168.100.97
Pinging 192.168.100.97 with 56 bytes of data:
Reply
Reply
Reply
Reply
Reply
from
from
from
from
from
192.168.100.97:
192.168.100.97:
192.168.100.97:
192.168.100.97:
192.168.100.97:
bytes=56
bytes=56
bytes=56
bytes=56
bytes=56
time<10ms
time<10ms
time<10ms
time<10ms
time<10ms
> rtrping 4 192.168.103.239
Pinging 192.168.103.239 with 56 bytes of data:
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{dest-ip-addr|"domain-name"}
dest-ip-addr
"domainname"
The IP Address of the IP network to tunnel, in the form of
xxx.xxx.xxx.xxx, where xxx is between 0-255.
The domain name to use for this query, with a maximum of 43characters,
enclosed in quotes. Example: rtrping 3 "www.carrieraccess.com"
[count]
This optional parameter sets the number of pings to send. Range is 1 to 32, default is 5.
[length]
This optional parameter sets the number of bytes to send in the ICMP echo request payload.
Range is 0 to 8000, default is 56.
{source-ip-addr}
Override the IP address that will be used as the source IP address in the ICMP echo request,
must be one of the Router interface IP addresses. Default is to use the IP address of the
interface from which the ping is sent. The IP address, in the form of xxx.xxx.xxx.xxx,
where xxx is a number from 0-255.
5-68
Axxius 800 - Release 2.2
CLI Commands
set
set
set alarms
set autoexit
set (bri)
set (bri) mode
set (bri) pmsync
set cclabel
set clock
set clock (1 and 2)
set date
set (ds0)
set (ds1)
set (ds1 card)
set (ds3)
set ethernet ip address
set external alarm
set (fxo)
set (fxsPS or fxsPSM)
set id
set idle
set ip gateway
set ipds0
set key
set login auth
set login support
set lsbackup
set lsprotect enable/disable
set lsprotect manual
set lsprotect nonrevertive
set lsprotect remove
set lsprotect revertive
Axxius 800 - Release 2.2
set (ocudp) baud
set (ocudp) loopback
set (ocudp) loopdetect
set (ocudp) mvec
set (ocudp) secondary
set (ocudp) selftest
set (ocudp) up/down
set (router) autologout
set (router) default
set (router) dhcp
set (router) dns
set (router) enhanced security
set (router) lmi
set (router) lmi poll
set (router) login auth
set (router) login prompt
set (router) ntp
set (router) password
set (router) port
set (router) ppp auth
set (router) ppp security
set (router) proxy
set (router) reboot
set (router) rip
set (router) snmp
set (router) stp
set (router) syslog
set (router-lan) filter forward
set (router-lan) framing
set (router-lan) gateway
5-69
CLI Commands
set
set (router-lan) ip address
set (router-lan) ipx network
set (router-lan) phy
set (router-lan) rip
set (router-lan) stp
set (router-lan) up/down
set (router-trunk) encapsulation
set (router-trunk) multilink group
set (router-trunk) speed
set (router-trunk) up/down
set (router-wan) dlci
set (router-wan) gre
set (router-wan) ip
set (router-wan) ip address
set (router-wan) ipx
5-70
set (router-wan) nat
set (router-wan) other
set (router-wan) ppp
set (router-wan) rip
set (router-wan) stp
set (router-wan) trunk
set (router-wan) up/down
set screen
set snmp
set time
set user
set (v35)
set (v54)
set verification
Axxius 800 - Release 2.2
CLI Commands
set
set alarms
Use the set alarms to manually set an alarm state for testing.
Syntax: set alarms {critical|major|minor} {off|on}
Example: set alarms critical on
The example set the alarm state of critical on.
{ciritical|major|minor}
critical
major
minor
Sets a critical alarm
Sets a major alarm.
Sets a minor alarm.
{off|on}
off
on
Disables the alarm state.
Enable the alarm state.
set autoexit
Use the set autoexit to set the autoexit feature.
Syntax: set autoexit {off|on}
Example: set autoexit on
The example will enable the auto-exit feature.
{off|on}
off
on
Axxius 800 - Release 2.2
Turn off the automatic logout option.
Enable the automatic exit option. Users will be automatically logged off
after 20 minutes of inactivity.
5-71
CLI Commands
set
set (bri)
Use the set (bri) command to setup the ISDN BRI card.
Syntax: set {bri-addr} {day|hour} {es|ses} {value}
Example: set 3:4 threshold day ses 30
To set the daily threshold to 30 Severely Errored Seconds on port 4 of a BRI card
in slot 3.
{bri-addr}
The {slot:port} address of the BRI card you want to apply the changes to.
slot
port
A for the controller card, or 1-8 for service cards.
Port number or range.
{setting}
crv
Set the Call Reference Value, when the BRI is set to 4:1 mode (lt4to1tdm). The CRV
value is between 1-768. Note: The CRV value for the BRI ports MUST be set the
same by both the Axxius 800 and the Access Navigator.
down
Take the ISDN line Out-of-Service.
threshold
Set the defect thresholds for ISDN lines to one of the following:
day
hour
value
Set the thresholds for the daily intervals.
es
Set the threshold for Errored Seconds (ES)
ses
Set the threshold for Severely Errored Seconds (SES)
Set the thresholds for hourly intervals.
es
Same as above
ses
Same as above
Range is 1 - 65535 seconds.
up
Put the ISDN line In-Service.
5-72
Axxius 800 - Release 2.2
CLI Commands
set
set (bri) mode
Use the set (bri) mode command to set the mode for the ISDN BRI Service.
Syntax: set {bri_card-addr} mode {setting}
Example: set 4 mode nt3ds0
To set the BRI card in slot 4 to use 3 DS0 LUNT
{bri_card-addr}
The slot number (1-8) of the Adit chassis that contains the BRI card.
{setting}
lt3ds0
nt3ds0
Set the BRI card mode to 3 DS0 LULT, used primarily for a subscriber line.
Set the BRI card mode to 3 DS0 LUNT, used primarily for a central office
connection.
set (bri) pmsync
Use the set (bri) pmsync command to set the source for performance monitoring
synchronization.
Syntax: set {bri_card-addr} pmsync {setting}
Example: set 4 pmsync axxius
To set the BRI card in slot 4 source for performance monitoring synchronization
to Axxius.
{bri_card-addr}
The slot number (1-8) that contains the BRI card.
{setting}
Set the operating mode to one of the following:
axxius
switch
Axxius 800 - Release 2.2
Set source to the Axxius
Set source to the switch
5-73
CLI Commands
set
set cclabel
Use the set cclable command to set a user defined cross-connect label.
Syntax: set cclabel {addr} {"label"}
Example: set cclabel a:1:1 "Idle Ch"
The example will set a user connect label "Idle Ch" on the DS0 a:1:1.
{addr}
ds0-addr
fxsPS-addr
fxsPSM-addr
tsr_trunk-addr
v35-addr
In the form of {slot:port|slot:port:channel}.
In the form of {slot:port}.
In the form of {slot:port}.
In the form of {slot:port:channel}.
In the form of {slot:port}.
{label}
The user defined label can be up to 8 characters, and must be enclosed in quotes.
set clock
Use the set clock command to configure signal clock switching.
Syntax: set clock {nonrevertive|revertive|switch}
Example: set clock nonrevertive
The example set the signal clock to nonrevertive mode.
{nonrevertive|revertive|switch}
nonrevertive
revertive
switch
5-74
Nonrevertive mode, meaning that the clock will not switch back to a
recently failed clock once that clock is restored
Revertive mode, the clock will automatically switch back and forth, if
possible, to a known good clock signal source
Force a signal clock switch-over. Allows the user to manually switch
from the primary clock to the secondary clock, and vice versa. Clock
source must be healthy for a switch to take place. This command is
not valid in revertive mode.
Axxius 800 - Release 2.2
CLI Commands
set
set clock (1 and 2)
Use the set clock (1 and 2) command to set the master transmit clock. The primary master clock
source may be used to clock each DS1 transmitter. The clock circuit automatically switches to
the secondary clock source if the primary clock fails.
Syntax: set {clock1|clock2} {source}
Example: set clock1 a:1
To set the primary master clock source to A:1.
Example: set clock2 1:2
Set the secondary master clock source to Quad T1 in slot 1 source selected.
{clock1}
Set primary master transmit clock source.
{clock2}
Set secondary master transmit clock source.
{source}
Set the clock source to one of the following:
bits1_t1
bits2_t1
bri-addr
Select BITS1 T1
Select BITS2 T1
Clock recovered from the BRI port on the BRI card (BRI card must be in
LUNT and 3DS0 mode)
Clock recovered from the DS1 receiver
Internal stratum 4E oscillator
ds1-addr
internal
NOTE: To set DS3 clocking see set (ds3) clock command.
set date
Use the set date command to set the date.
Syntax: set date {mm/dd/yyyy}
Example: set date 1/1/2002
The example will set the date to January 1, 2002.
{mm/dd/yyyy}
mm
dd
yyyy
Axxius 800 - Release 2.2
Represents the month. Range is 1-12, single digits can be entered.
Represents the Day. Range is 1-31, single digits can be entered.
Represents the year. Range is 1999-2106.
5-75
CLI Commands
set
set (ds0)
Use the set (ds0) command to setup one or all DS0s in a DS1. The command specifies DS0 or
range of DS0s, and the setting to apply.
set(ds0) signal
Use the set (ds0) signal command to setup one or all DS0s in a DS1 signal.
Syntax: set {ds0-addr} signal {emdw|emi|emicpd|emw|gs|ls}
Example: set a:1:1-4 signal emi
To set the signal type to E&M immediate start for channels 1-4, port 1, slot A
on a DS1 Controller.
{ds0-addr}
The Controller DS0 addresses are different on the DS3 and DS1 Controller, however the
DS0 address on the service cards does not change with Controller type (DS3 or DS1).
DS0 Address on a DS3 Controller in the form {slot:port:channel:sub-channel}
slot
A for the DS3 Controller card.
port
Port number, range or all.
ds1 channel DS1 channel number, range or all.
ds0 channel DS0 channel number, range or all.
DS0 Address on a DS1 Controller or service cards (with DS1 or DS3 controller) in
the form {slot:port:channel}
slot
A for the DS1 Controller card, or 1-8 for service cards.
port
Port number, range or all.
channel
Channel number, range or all.
{emdw|emi|emicpd|emw|gs|ls}
emdw
emi
emicpd
emw
gs
ls
5-76
E&M delayed wink start. Used for ANI/DNS
E&M immediate start with ringback (used for D3 PLAR and DPT)
E&M immediate start with calling party disconnect with ringback
E&M wink start
Ground start signaling
Loop start signaling
Axxius 800 - Release 2.2
CLI Commands
set
set(ds0) type
Use the set (ds0) type command to setup one or all DS0s in a DS1 signal type.
Syntax: set {ds0-addr} type {data|voice}
Example: set 3:1:1-4 type voice
To set the traffic type to voice on channels 1-4 on port 1 of slot 3 on a service
card.
{ds0-addr}
The Controller DS0 addresses are different on the DS3 and DS1 Controller, however the
DS0 address on the service cards does not change with Controller type (DS3 or DS1).
DS0 Address on a DS3 Controller in the form {slot:port:channel:sub-channel}
slot
A for the DS3 Controller card.
port
Port number, range or all.
ds1 channel DS1 channel number, range or all.
ds0 channel DS0 channel number, range or all.
DS0 Address on a DS1 Controller or service cards (with DS1 or DS3 controller) in
the form {slot:port:channel}
slot
A for the DS1 Controller card, or 1-8 for service cards.
port
Port number, range or all.
channel
Channel number, range or all.
{data|voice}
data
voice
Axxius 800 - Release 2.2
Set the DS0 up to carry data (clear channel)
Set the DS0 up to carry voice traffic (robbed-bit signaling)
5-77
CLI Commands
set
set (ds1)
Use the set (ds1) command to set up DS1 interfaces. The command specifies a range of
interfaces and the setting to apply.
Syntax: set {ds1-addr} {setting}
Example: set a:1 framing esf
To set DS1 1 (port 1) on a DS1 Controller to use ESF framing.
{ds1-addr}
The Controller DS1 addresses are different on the DS3 and DS1 Controller, however the
DS1 address on the services cards does not change with Controller type (DS3 or DS1). \
DS1 Address on a DS3 Controller in the form {slot:port:channel}
slot
A for the DS3 Controller card.
port
Port number, range or all.
ds1 channel Channel number, range or all.
DS1 Address on a DS1 Controller or service cards (with DS1 or DS3 controller) in
the form {slot:port}
slot
A for the DS1 Controller card, or 1-8 for service cards.
port
Port number, range or all.
{setting}
ais
down
equipment
fdl
framing
5-78
Enable/Disable AIS Forwarding on the DS1. Default is Disabled
Set the DS1 as Out-of-Service
Set equipment loopback on the DS1
loopdown
Disable equipment loopback on the DS1
loopup
Enable equipment loopback on the DS1
Set the Facilities Data Link (FDL) capabilities
none
Disable FDL output messages
t1403
Enable T1.403 FDL performance messages
Set the DS1 framing type to one of the following:
d4
To D4 Superframe (SF) framing
esf
To Extended Superframe (ESF) framing
Axxius 800 - Release 2.2
CLI Commands
set
id
Set the DS1 circuit identification name. This is the same as dsx1Circuit
Identifier from DS1 MIB transmission vendor’s identification. String
text must be enclosed in quotes.
Example: set {ds1-addr} id {"id-name"}
lbo
line
linecode
loopdetect
payload
Axxius 800 - Release 2.2
{id-name} = transmission vendor’s ID, up to 30 characters, in quotes.
Set the Line Build Out (LBO) to one of the following: Note: this
options is not applicable on a DS1 within a DS3.
1
DSX-1 equalization for 0-133 feet (equivalent to CSU
attenuation for LBO of 0dB)
2
DSX-1 equalization for 133-266 feet
3
DSX-1 equalization for 266-399 feet
4
DSX-1 equalization for 399-533 feet
5
DSX-1 equalization for 533-655 feet
6
CSU attenuation for LBO of -7.5dB
7
CSU attenuation for LBO of -15dB
8
CSU attenuation for LBO of -22.5dB
Turn a line loopback to the DS1 interface on or off. If the line command
is not used, the default for line loopback is loopdown.
loopdown
Disable the line loopback
loopup
Enable a DS1 line loopback toward the DS1 drop
Set the DS1 interface line coding to one of the following. If the linecode
command is not used, the default for linecode is B8ZS.
Note: this options is not applicable on a DS1 within a DS3.
ami
Alternate Mark Inversion line coding
b8zs
Binary 8 Zero Substitution line coding.
Enable detection of CSU loop code (10000 - loopup; 100 - loopdown)
on
Enable detection
off
Disable detection
Apply a payload loopback to the DS1 interface. If the payload
command is not used, the default for payload loopback is loopdown.
loopdown
Disable the payload loopback
loopup
Enable the payload loopback
5-79
CLI Commands
set
threshold
up
5-80
Set default thresholds for a DS1. Defaults for all are 0.
day
Set threshold for a daily interval
bes
Bursty errored seconds range: 0 - 86400
css
Controlled slip seconds range: 0 - 86400
dm
Degraded minutes range: 0 - 1440
es
Errored seconds range: 0 - 86400
lcv
Line code violations range: 0 - 133401600
les
Line errored seconds range: 0 - 86400
pcv
Path code violations range: 0 - 133401600
sefs
Severely errored frame seconds range: 0 - 86400
ses
Severely errored seconds range: 0 - 86400
uas
Unavailable seconds range: 0 - 86400
min15
Set threshold for a 15 minute interval
bes
Bursty errored seconds range: 0 - 900
css
Controlled slip seconds range: 0 - 900
dm
Degraded minutes range: 0 - 15
es
Errored seconds range: 0 - 900
lcv
Line code violations range: 0 - 1389600
les
Line errored seconds range: 0 - 900
pcv
Path code violations range: 0 - 1389600
sefs
Severely errored frame seconds range: 0 - 900
ses
Severely errored seconds range: 0 - 900
uas
Unavailable seconds range: 0 - 900
Set the DS1 as In-Service. Enables alarm reporting (and LED) for the
port specified
Axxius 800 - Release 2.2
CLI Commands
set
set (ds1 card)
Use the set (ds1 card) commands to configure DS1 card types. These commands apply to the
Quad DS1/E1 (hardened) and Quad DS1 ADPCM (hardened) service cards.
set (ds1 card) spantype
Use the set (ds1 card) spantype command to set the span type (T1 or E1) on the DS1 type
card. Note: this CLI command is not supported in this release.
Syntax: set {ds1_card-addr} {e1span|t1span}
Example: set 6 e1span
To set the Quad DS1/E1 card in slot 6 to E1 mode.
{ds1_card-addr}
The slot number (1-6) that contains a DS1 type card (Quad DS1/E1 or Quad DS1 ADPCM
service card).
{e1span|t1span}
e1span
t1span
Axxius 800 - Release 2.2
Enables E1 capability on this card.
Enables T1 capability on this card. (Default)
5-81
CLI Commands
set
set (ds1 card) adpcm map
Use the set (ds1 card) adpcm map command to set voice compression map on the Quad
DS1 ADPCM card.
Syntax: set {adpcm_card-addr} adpcm {none|map1|map2|map3}
Example: set 5 adpcm map1
{adpcm_card-addr} - The slot number (1-6) that contains the Quad DS1 ADPCM card.
{none|map1|map2|map3}
none
map1, map2 or map3
DS0
Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
5-82
None will disable compression on the card. Default.
Map setting, see chart below
MAP 1
X-Port
Backplane
Analog
Bus
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
64n
X1/2
X3/4
X5/6
X7/8
X9/10
X11/12
X14/15
X16/17
X18/19
X20/21
X22/23
X24
Not Avail
MAP 2
X-Port
Backplane
Analog
Bus
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
X1/2
X3/4
X5/6
X7/8
X9/10
X11/12
X13/14
X15/16
X17/18
X19/20
X21/22
X23/24
X-Port
Analog
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
32n
64n
MAP 3
Backplane
Bus
X1/2
X3/4
X5/6
X7/8
X9/10
X11/12
X13/14
X15/16
X17/18
X19/20
X21/22
X24
Not Avail
Axxius 800 - Release 2.2
CLI Commands
set
set (ds3)
Use the set (ds3) command to set up DS3 interfaces. The command specifies a range of
interfaces and the setting to apply.
Syntax: set {ds3-addr} {setting}
Example: set a:1 framing m23
To set DS3 1 (port 1) on a DS3 Controller (slot A) to use M23 framing.
{ds3-addr}
DS3 address in the form {slot:port}.
slot
port
A for the controller card, or 1-8 for service cards.
Port number, range or all.
{setting}
down
up
berthreshold
clock
dejitter
equipment
facility id
Axxius 800 - Release 2.2
Set the DS3 as Out-of-Service
Set the DS3 as In-Service. Enables alarm reporting (and LED) for the
port specified
Set Bit Error Rate protection switchover threshold.
{value}
4-8 for 10e-4 to 10e-8
Set the transmit clock source
loop
Set to clock recovered from the DS3 receive
normal
Set to master transmit clock source
Turn the De-jitter buffer on or off
off
De-jitter buffer off
on
De-jitter buffer on
Set equipment loopback on the DS3 or PMDL (Path Maintenance Data
Link) ID
id
Set the DS3 equipment PMDL ID string
Command syntax: set {ds3-addr} equipment id
{"string"}
{"string"} = transmission vendor’s identification, up to
30 characters, enclosed in quotes.
loopdown
Disable equipment loopback on the DS3
loopup
Enable equipment loopback on the DS3
Set the DS3 facility PMDL ID string
Command syntax: set {ds3-addr} facility id {"string"}
{"string"} = transmission vendor’s identification, up to 38 characters,
enclosed in quotes.
5-83
CLI Commands
set
frame
framing
gennum
id
line
location id
loopdetect
payload
portnum
protect
5-84
Set the DS3 frame PMDL ID string
Command syntax: set {ds3-addr} frame {"string"}
{"string"} = transmission vendor’s identification, up to 10 characters,
enclosed in quotes.
Set the DS3 framing type
cbit
To C-bit framing
m23
To M23 framing
Set the DS3 generator number PMDL string
Command syntax: set {ds3-addr} gennum {"string"}
{"string"} = transmission vendor’s identification, up to 38 characters,
enclosed in quotes.
Set the DS3 ID.
Command syntax: set {ds3-addr} id {"id-name"}
{"id-name"} = up to 30 characters, enclosed in quotes.
Set a line loopback on the DS3.
loopdown
Disable loopback on the DS3
loopup
Enable loopback on the DS3
Set the DS3 location PMDL ID string
Command syntax: set {ds3-addr} location id {"string"}
{"string"} = transmission vendor’s identification, up to 11 characters,
enclosed in quotes.
Set detection of loopback requests
off
Disable detection of loopback requests
on
Enable detection of loopback requests
Set the payload loopback on the DS3
loopdown
Disable the payload loopback
loopup
Enable the payload loopback
Set the DS3 port number PMDL string
Command syntax: set {ds3-addr} portnum {"string"}
{"string"} = transmission vendor’s identification, up to 38 characters,
enclosed in quotes.
Set port protection on the DS3
off
Disable port protection of loopback requests
on
Enable port protection of loopback requests
Axxius 800 - Release 2.2
CLI Commands
set
reversion
Set protection reversion on the DS3
off
Disable protection reversion of loopback requests
on
Enable protection reversion of loopback requests
threshold
Set defect thresholds for a DS3. Defaults for all are 0.
unit
Axxius 800 - Release 2.2
day
Set threshold for a daily interval
ccv
C-bit code violation range: 0 - 86400
ces
C-bit errored seconds range: 0 - 86400
cses
C-bit severely errored seconds range: 0 - 86400
lcv
Line code violations range: 0 - 133401600
les
Line errored seconds range: 0 - 86400
pcv
Path code violations range: 0 - 133401600
pes
P-bit errored seconds range: 0 - 86400
pses
P-bit severely errored seconds range: 0 - 86400
sefs
Severely errored frame seconds range: 0 - 86400
uas
Unavailable seconds range: 0 - 86400
min15
Set threshold for a 15 minute interval
ccv
C-bit code violation range: 0 - 86400
ces
C-bit errored seconds range: 0 - 86400
cses
C-bit severely errored seconds range: 0 - 86400
lcv
Line code violations range: 0 - 133401600
les
Line errored seconds range: 0 - 86400
pcv
Path code violations range: 0 - 133401600
pes
P-bit errored seconds range: 0 - 86400
pses
P-bit severely errored seconds range: 0 - 86400
sefs
Severely errored frame seconds range: 0 - 86400
uas
Unavailable seconds range: 0 - 86400
Set the DS3 unit code PDML string
Command syntax: set {ds3-addr} unit {"string"}
{"string"} = transmission vendor’s identification, up to 6 characters,
enclosed in quotes.
5-85
CLI Commands
set
set ethernet ip address
Use the set ethernet ip address command to set the Ethernet address for the Axxius 800.
Syntax: set ethernet ip address {ip-addr} [mask]
Example: set ethernet ip address 172.26.100.25 255.255.255.0
{ip-addr}
Set the IP address for the Axxius 800, using the form xxx.xxx.xxx.xxx, where xxx is a
number from 0 to 255.
[mask]
Set the subnet mask, using the form xxx.xxx.xxx.xxx, where xxx is a number from 0 to 255.
This is an optional setting.
set external alarm
Use the set external alarm command to set the external alarm inputs.
Syntax: set external alarm {alarm-num}
{[severity]|[description]}
Example: set external alarm 1 "test"
The example will set the external alarm #1 description name to "test".
Example: set external alarm 2 major
The example will set the external alarm #2 severity level to major.
Example: set external alarm 3 critical "test2"
The example will set the external alarm #3 severity level to critical, with a
description name of "test2".
{alarm-num}
Set the alarm number to configure, range is 1-10.
[severity]
Set the alarm severity level to the following:
critical
info
minor
major
5-86
Set the external alarm severity level to critical
Set the external alarm severity level to information
Set the external alarm severity level to minor
Set the external alarm severity level to major
Axxius 800 - Release 2.2
CLI Commands
set
set (fxo)
Use the set (fxo) command to setup one or all of the voice channels of an FXO card. The
command specifies the list of voice channels within that card, and the setting to apply.
Syntax: set {fxo-addr} {setting}
Example: set 2:1 signal ls
Set the FXO on slot 2, port 1 to signaling type loop start.
{fxo-addr}
List of voice channels to apply setting to, in the form {slot:port}.
slot
port
Slot number 1-8, location of the FXO card
Port number or range
{setting}
rxgain
signal
txgain
Axxius 800 - Release 2.2
The receive level range is -9 to +7 (db). Available values are -9, -7, -6, -5,
-4, -3, -2, 0, 2, 3, 4, 5, 6, and 7
Set the DS0 signaling type
dpt
Set the DS0 to Dial Pulse Terminate
gs
Set the DS0 to Ground Start signaling
ls
Set the DS0 to Loop Start signaling
lscpd
Set the DS0 to Loop Start Calling Party Disconnect
The transmit level range is -9 to +7 (db). Available values are -9, -7, -6,
-5, -4, -3, -2, 0, 2, 3, 4, 5, 6, and 7
5-87
CLI Commands
set
set (fxsPS or fxsPSM)
Use the set (fxsPS or fxsPSM) command to setup voice channels of an Single Channel POTS
card (FXS PS) or the POTS card with modem (FXS PSM). The command specifies the list of
voice channels, and the setting to apply.
Syntax: set {fxsPS-addr|fxsPSM-addr} {setting}
Example: set 3:1 signal ls
To set the port on slot 3 to Loop Start signaling.
{fxsPS-addr|fxsPSM-addr}
Voice channels to apply setting to, in the form of {slot:port}.
slot
port
Slot number 1-8, location of the FXS PS or FXS PSM card
Port number or range
{setting}
rxgain
signal
txgain
The receive level range is -12 to +6 (db). Available in .25 dB increments
Set the DS0 signaling type
ls
Set to Loop Start signaling
lsrb
Set to Loop Start signaling with reverse battery
Transmit level range is -12 to +6 (db). Available in .25 dB increments
set id
Use the set id command to the unit ID.
Syntax: set id {"id-name"}
Example: set id "Axxius800"
Axxius800>
{"id-name"}
The name must be unique with a maximum of 20 characters. Name must be enclosed in
quotes.
5-88
Axxius 800 - Release 2.2
CLI Commands
set
set idle
Use the set idle command to set the system-wide idle code sent on DS0s.
Syntax: set idle {pattern}
Example: set idle 0xff
{pattern}
A hexadecimal number with a range from 0x00 to 0xff. This number must be preceeded by
0x.
set ip gateway
Use the set ip gateway command to set the IP gateway address (also known as the default route)
for the Axxius 800. The command specifies the numeric Internet Protocol (IP) address. The new
gateway address will not take effect until Controller is reset (reset command).
Syntax: set ip gateway {ip-addr}
Example: set ip gateway 192.168.100.1
{ip-addr}
Set the IP gateway address for the Axxius 800, using the form xxx.xxx.xxx.xxx, where xxx
is a number from 0 to 255.
Axxius 800 - Release 2.2
5-89
CLI Commands
set
set ipds0
Use the set ipds0 command to setup the DS0 management channel.
Note: the DS0 selected as the DS0 management channel can only reside on the Controller T1.
Syntax: set ipds0 {setting} [ds0-addr|ip-addr]
Example: set ipds0 assign a:1:24
The example sets the DS0 management channel to slot A, port 1, channel 24.
{setting}
assign
delete
down
ip address
navalarm
up
Assign the DS0 as the IP management channel
Removes the IP over DS0 management channel [default]
Set the DS0 management channel down (disables) [default]
Set the DS0 management channel’s IP address and optional subnet mask
Set reporting of Access Navigator alarm. If IP over DS0 management is
up and a Navigator is not attached, an alarm will be set. This command
allows the operator to suppress the alarm in instances when the Axxius is
not connected to a Navigator.
Off - Set reporting of Navigator alarm off.
On - Set reporting of Navigator alarm on.
Set the DS0 management channel up (enables)
[ds0-addr|ip-addr]
The Controller DS0 addresses are different on the DS3 and DS1 Controller.
DS0 Address on a DS3 Controller in the form {slot:port:channel:sub-channel}
slot
A for the DS3 Controller card.
port
Port number, range or all.
ds1 channel DS1 channel number, range or all.
ds0 channel DS0 channel number, range or all.
DS0 Address on a DS1 Controller in the form {slot:port:channel}
slot
A for the DS1 Controller card.
port
Port number, range or all.
ip-addr Setup the DS0 management channel IP address and the optional subnet mask,
in the form of xxx.xxx.xxx.xxx, where xxx is between 0-255.
5-90
Axxius 800 - Release 2.2
CLI Commands
set
set key
Use the set key command to enable a specific keyed feature. To acquire a feature key code,
contact Carrier Access Customer Service. Currently, keyed features (if available) can be
enabled on a Controller or a Router.
Syntax: set [rtr_card-addr] key {"key-code"}
Example: set 4 key "q0B8yma2IsSL+1BarY0u"
[rtr_card-addr]
The slot number (1-8) that contains the Router card. This optional parameter is used for
router specific keyed features. If a slot is not entered, key is directed to the Controller.
{"key-code"}
The key code is entered to enable the specific feature.
set login auth
Use the set login auth command to set the authentication method for controller logins, with
local database or external RADIUS server. When set to RADIUS the controller will try the
configured RADIUS servers first. If none of the configured RADIUS server reply to the request,
the controller will use its local database of users to authenticate the login. An attempt set login
authentication to RADIUS will fail if there is not at least 1 RADIUS server configured.
Syntax: set login auth {local|radius}
Example: set login auth radius
The example will set the login authentication process to RADIUS.
{local|radius}
local
radius
Axxius 800 - Release 2.2
Authenticate user logins via the controller database. Default.
Authenticate user logins via the external RADIUS servers.
5-91
CLI Commands
set
set login support
Use the set login support command to enable or disable the internal login accounts for Carrier
Access Support personnel for the Controller and Router cards.
Syntax: set login support {disable|enable}
Example: set login support disable
The example will prohibit logins via Carrier Access Support passwords.
{disable|enable}
disable
enable
Prohibit logins via Carrier Access Support passwords.
Allow logins via Carrier Access Support passwords.
set lsbackup
Use the set lsbackup commands to define the backup protection slot. The service card in this
slot must be a hardened Quad T1 service card and can be in any of the 8 Axxius service card
slots.
Syntax: set lsbackup {t1_card-addr} [remove]
Example: set lsbackup 8
Example: set lsbackup 8 remove
{t1_card-addr}
The slot number (1-8) that contains a hardened Quad T1 Service card to be used as backup.
Note: only one card may be defined as the backup protection card. If this command
is applied to a second slot the following message will appear:
*-New Backup slot cannot be assigned--old assignment must be
removed first.
To change the backup protection card, a set lsbackup {slot} remove command must be
applied first.
[remove]
This setting will stop the defined T1 service card as a backup card. Note: the correct slot
for the current backup protection card must be used.
5-92
Axxius 800 - Release 2.2
CLI Commands
set
set lsprotect enable/disable
Use the set lsprotect enable/disable command to set the global enable or disable the Low
Speed Protection options on the system.
Syntax: set lsprotect {disable|enable}
Example: set lsprotect disable
{disable|enable}
disable
enable
disable Low Speed Protection on the Axxius system
enable Low Speed Protection on the Axxius system
set lsprotect manual
Use the set lsprotect manual command to set manual mode control for protected ports. Note:
this command is effective only if lsprotect is enabled (set lsprotect enable).
Syntax: set lsprotect {slot:port} manual
{disable|enable|release|switchback|switchover} [hold]
Example: set lsprotect 5:1 manual enable
{slot:port}
The {slot:port} address of the protected port to be configured.
slot
port
Slot number (1-8) where a Quad T1 card is located
Port number or range (1-4)
{disable|enable|release|switchback|switchover}
disable
enable
release
switchback
switchover
Axxius 800 - Release 2.2
Disables protection for protected port(s)
Enables protection for protected port(s) that have been automatically or
manually disabled.
Releases manual hold for protected port(s).
Switches protected port(s) back to home circuit(s).
[hold] Holds manual switchbacks in-force until user releases hold.
Manually switches protected ports to backup circuit(s).
[hold] Holds manual switchbacks in-force until user releases hold.
5-93
CLI Commands
set
set lsprotect nonrevertive
Use the set lsprotect nonrevertive command to set low speed protected port(s) to non-revertive
mode.
When a port is in non-revertive mode and a failure occurs the port is switched to the protection
port, and will remain there until manually reset. However, if the port becomes healthy again and
another port has a failure the first port will revert, and the second port will then be protected.
Syntax: set lsprotect {slot:port} nonrevertive [priority]
[1-7]
Example: set lsprotect 5:1 nonrevertive priority 2
{slot:port}
The {slot:port} address of the protected port to be configured.
slot
port
Slot number (1-8) where a Quad T1 card is located
Port number or range (1-4)
[priority]
An optional parameter, which defines the port priority in the event that multiple protection
requests are received for the same port number on different cards.
[1|2|3|4|5|6|7]
A parameter set with low speed priority, which sets the value of the port priority. Range is
1-7, default is 7. Priority 1 is the highest priority, 7 is the lowest priority.
5-94
Axxius 800 - Release 2.2
CLI Commands
set
set lsprotect remove
Use the set lsprotect remove command to remove port from protected mode.
Syntax: set lsprotect {slot:port} remove
Example: set lsprotect 5:2 remove
Do you really want to do this? y
*-Protected port(s) not removed since they were not previously
assigned.
Example: set lsprotect 5:2 remove
> set lsprotect 5:2 remove
Do you really want to do this? y
OK
{slot:port}
The {slot:port} address of the protected port to be configured.
slot
port
Axxius 800 - Release 2.2
Slot number (1-8) where a Quad T1 card is located
Port number or range (1-4)
5-95
CLI Commands
set
set lsprotect revertive
Use the set lsprotect revertive command to set low speed protected port(s) to revertive mode.
When a port is set to revertive mode and a failure occurs the port is switched to the protection
port. After 5 minutes, with no failures, the port reverts back. If there are 3 reverts in a 24 hour
period the port is locked out and will remain with the protection port for 24 hours of no failures,
or is manually reset. With 24 hours of no failures one of the 3 reverts is removed from the
counter, and if another failure occurs the counter goes back up to 3 and will go into lockout
mode again.
Syntax: set lsprotect {slot:port} revertive [priority|reset]
[1-7]
Example: set lsprotect 5:2 revertive priority 2
Example: set lsprotect 6:1 revertive reset
Slot 6 Port 1 is currently in protective backup.
Resetting the automatic Lockout will cause service interruption
for port(s) currently being backed up. Traffic will be forced
back to the home port(s)
{slot:port}
The {slot:port} address of the protected port to be configured.
slot
port
Slot number (1-8) where a Quad T1 card is located
Port number or range (1-4)
[priority|reset]
priority
reset
An optional parameter, which defines the port priority in the event that
multiple protection requests are received for the same port number on
different cards
If the port is already in a protective mode "reset can be selected. The
following message will appear.
[1|2|3|4|5|6|7]
A parameter set with low speed priority, which sets the value of the port priority. Range is
1-7, default is 7. Priority 1 is the highest priority, 7 is the lowest priority.
5-96
Axxius 800 - Release 2.2
CLI Commands
set
set (ocudp) baud
Use the set (ocudp) baud command to configure the Baud Rate for OCU-DP ports.
Syntax: set {ocudp-addr} baud {rate}[sw56|sw56cp]
Example: set 3:2 baud 2400
Set the baud rate on port 2 to 2400, on the OCU-DP card in slot 3.
{ocudp-addr}
The {slot:port} address of the OCU-DP card you want to apply the changes to.
slot
port
Slot number (1-8) where the OCU-DP is located
Port number or range.
{rate}
2400
4800
9600
19200
38400
56000*
64000
Set OCU-DP baud rate to 2400
Set OCU-DP baud rate to 4800
Set OCU-DP baud rate to 9600
Set OCU-DP baud rate to 19200
Set OCU-DP baud rate to 38400
Set OCU-DP baud rate to 56000. This is the default.
sw56
Set to switched 56 service
sw56cp
Set to switched 56 service with call progress capability. Sends
special call progress CMI codes to DSU.
Set OCU-DP baud rate to 64000
Axxius 800 - Release 2.2
5-97
CLI Commands
set
set (ocudp) loopback
Use the set (ocudp) loopback command to manually set OCU/CSU loopback tests.
Syntax: set {ocudp-addr} loopback {csu|ocu} {loopdown|loopup}
Example: set 3:2 loopback csu loopdown
{ocudp-addr}
The {slot:port} address of the OCU-DP card you want to apply the changes to.
slot
port
Slot number (1-8) where the OCU-DP is located
Port number or range.
{csu|ocu}
csu
ocu
Set CSU manual loopback tests
Set OCU manual loopback tests
{loopdown|loopup}
loopdown*
loopup
5-98
Stop CSU/OCU manual loopback test. Loopdown is default.
Start CSU/OCU manual loopback test
Axxius 800 - Release 2.2
CLI Commands
set
set (ocudp) loopdetect
Use the set (ocudp) loopdetect to configure the OCU non-latching/latching loopback code
detection.
Syntax: set {ocudp-addr} loopdetect {csu|dsu|ocu} {llb|nllb}
{disable|enable}
Example: set 3:2 loopdetect csu llb enable
{ocudp-addr}
The {slot:port} address of the OCU-DP card to apply the changes to.
slot
port
Slot number (1-8) where the OCU-DP is located
Port number or range.
{csu|dsu|ocu}
csu
dsu
ocu
Set CSU manual loop codes detection
Set DSU manual loop codes detection
Set OCU manual loop codes detection
{llb|nllb}
llb
nllb
Set up latching loopback detection
Set up non-latching loopback detection
{disable|enable}
disable
enable
Axxius 800 - Release 2.2
Disable loop detection
Enable loop detection
5-99
CLI Commands
set
set (ocudp) mvec
Use the set (ocudp) mvec to set Majority Vote Error Correction (MVEC).
Syntax: set {ocudp-addr} mvec {disable|enable}
Example: set 3:2 mvec enable
{ocudp-addr}
The {slot:port} address of the OCU-DP card you want to apply the changes to.
slot
port
Slot number (1-8) where the OCU-DP is located
Port number or range.
{disable|enable}
disable*
enable
Disable the error correct. Disable is default.
Enable the error correct
set (ocudp) secondary
Use the set (ocudp) secondary to configure the secondary channel service.
Syntax: set {ocudp-addr} secondary {disable|enable}
Example: set 3:2 secondary enable
{ocudp-addr}
The {slot:port} address of the OCU-DP card you want to apply the changes to.
slot
port
Slot number (1-8) where the OCU-DP is located
Port number or range.
{disable|enable}
disable*
enable
5-100
Disable the secondary channel service. Disable is default.
Enable the secondary channel service
Axxius 800 - Release 2.2
CLI Commands
set
set (ocudp) selftest
Use the set (ocudp) selftest to initiate the OCU-DP card to perform a self test. This request will
display a message to wait 8 seconds before requesting selftest status with the status command.
Syntax: set {ocudp-addr} selftest
Example: set 3:2 selftest
{ocudp-addr}
The {slot:port} address of the OCU-DP card you want to apply the changes to.
slot
port
Slot number (1-8) where the OCU-DP is located
Port number or range.
set (ocudp) up/down
Use the set (ocudp) up/down to put the OCU-DP line In or Out-of-Service.
Syntax: set {ocudp-addr} {down|up}
Example: set 3:2 up
Set the OCU-DP card in slot 3, port 2 as In-Service.
{ocudp-addr}
The {slot:port} address of the OCU-DP card you want to apply the changes to.
slot
port
Slot number (1-8) where the OCU-DP is located
Port number or range.
{up|down}
down
up
Set OCU-DP port as Out-of-Service
Set OCU-DP port as In-Service
Axxius 800 - Release 2.2
5-101
CLI Commands
set
set (router) autologout
Use the set (router) autologout command to set the period of time of inactivity after which the
user will be automatically logged-out of a Telnet session.
Syntax: set {rtr_card-addr} autologout {minutes}
Example: set 3 autologout 0
The example will disable the auto-logout timer in the Router in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{minutes}
The minutes of inactivity before auto-logout occurs. Range is 0-255. An entry of "0" will
disable the auto-logout timer.
set (router) default
Use the set (router) default command to reset the TSR card to its default configuration settings.
This command will cause the TSR card to perform a reboot.
Syntax: set {rtr_card-addr} default
Example: set 3 default
Do you really want to do this ? y
OK
The example will reset the Router in slot 3 to its defaults.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
5-102
Axxius 800 - Release 2.2
CLI Commands
set
set (router) dhcp
Use the set (router) dhcp commands to configure the DHCP functions.
set (router) dhcp disable
Use the set (router) dhcp disable command to disable both DHCP server and DHCP relay
functionality for the specified Router card.
Syntax: set {rtr_card-addr} dhcp disable
Example: set 3 dhcp disable
The example will set the Router in slot 3 to disable DHCP.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
set (router) dhcp relay server
Use the set (router) dhcp relay server command to enable a DHCP relay and assign a
DHCP server address for the specified Router card.
Syntax: set {rtr_card-addr} dhcp relay server
{server-number} {ip-addr} {"profile-name"}
Example: set 3 dhcp relay server 1 134.200.3.45 "remotewan"
The example will set the TSR in slot 3 to enable DHCP relay server 1 at IP
address 134.200.3.45 on WAN "remotewan".
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{server-number}
The server number (1 or 2) to specify.
{ip-addr}
The IP address of the server to relay to, in the form of xxx.xxx.xxx.xxx, where xxx is
between 0-255.
{"profile-name"}
The profile name for the Router interface that is used to reach this destination. This name
must be enclosed in quotes.
Axxius 800 - Release 2.2
5-103
CLI Commands
set
set (router) dhcp server dnsserver
Use the set (router) dhcp server dnsserver command to set the IP address of up to 4 DNS
servers that the DHCP server will inform the clients of.
Syntax: set {rtr_card-addr} dhcp server dnsserver {number}
{ip-addr}
Example: set 5 dhcp server dnsserver 4 122.104.33.220
The example will set the 4th DNS server address for the DHCP server on the
Router card in slot 5 to 122.104.33.220
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{number}
The DNS server entry, 1-4.
{ip-addr}
The address of the DNS server, in the form of xxx.xxx.xxx.xxx, where xxx is between
0-255.
set (router) dhcp server domain
Use the set (router) dhcp server domain command to select the domain name to provide
to DHCP clients.
Syntax: set {rtr_card-addr} dhcp server domain
{"domain-name"}
Example: set 5 dhcp server domain "carrieraccess.com"
The example sets the domain name to "carrieraccess.com" in the DHCP server
on the TSR in slot 5.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"domain-name"}
The domain name, with a maximum of 43 characters. Name must be enclosed in quotes.
5-104
Axxius 800 - Release 2.2
CLI Commands
set
set (router) dhcp server duration
Use the set (router) dhcp server duration command to set the lease duration that the
DHCP server applies to client assignments.
Syntax: set {rtr_card-addr} dhcp server duration
{hours:minutes}
Example: set 5 dhcp server duration 3:45
The example set the lease duration for the DHCP server on the Router in slot 5
to 3 hours and 45 minutes.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{hours:minutes}
The lease duration in hours and minutes, in the form of HH:MM.
HH = 1-999, MM = 1-60.
set (router) dhcp server netbios nameserver
Use the set (router) dhcp server netbios nameserver command to set the NetBIOS Name
Server (NBNS - RFC 1001/1002) that the DHCP server provides to clients.
Syntax: set {rtr_card-addr} dhcp server netbios nameserver
{1|2} {ip-addr}
Example: set 5 dhcp server netbios nameserver 1 192.168.100.80
Note: DHCP server must first be enabled with the "startaddr" command. See set
(router) dhcp server startaddr on page 5-107.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{1|2}
The NetBIOS Name Server entry.
{ip-addr}
The NBNS IP address, in the form of xxx.xxx.xxx.xxx, where xxx is between 0-255.
Axxius 800 - Release 2.2
5-105
CLI Commands
set
set (router) dhcp server netbios nodetype
Use the set (router) dhcp server netbios nodetype command to set the NetBIOS node
type (see RFC 1001/1002) that the DHCP server provides to clients.
Syntax: set {rtr_card-addr} dhcp server netbios nodetype
{type-number}
Example: set 5 dhcp server netbios nodetype 1
The example will set the NetBIOS node type to B-node.
Note: DHCP server must first be enabled with the "startaddr" command. See set
(router) dhcp server startaddr on page 5-107.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{type-number}
The value is specified as a single octet that identifies the client type.
1
2
B-node
P-node
4
8
M-node
H-node
set (router) dhcp server netbios scope
Use the set (router) dhcp server netbios scope command to set the NetBIOS scope value
(see RFC 1001/1002) that the DHCP server provides to clients.
Syntax: set {rtr_card-addr} dhcp server netbios scope
{scope-name}
Example: set 5 dhcp server netbios scope "Accounting"
Note: DHCP server must first be enabled with the "startaddr" command. See set
(router) dhcp server startaddr on page 5-107.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{scope-name}
The Scope is a DHCP option that represents a grouping of computers on a subnet using the
same NetBIOS name. Enter up to 41 alphanumeric characters for the scope-name, enclosed
in quotes.
5-106
Axxius 800 - Release 2.2
CLI Commands
set
set (router) dhcp server startaddr
Use the set (router) dhcp server startaddr command to enable the DHCP server on the
specified Router card.
Syntax: set {rtr_card-addr} dhcp server startaddr
{ip-addr} {count}
Example: set 4 dhcp server startaddr 134.200.3.1 254
The example will set the TSR in slot 4 to enable the DHCP server with 254
address pool starting at 134.200.3.1.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{ip-addr}
The starting address of the client address pool, in the form of xxx.xxx.xxx.xxx, where xxx
is between 0-255.
{count}
The number of IP addresses in the client address pool (1-254).
Axxius 800 - Release 2.2
5-107
CLI Commands
set
set (router) dns
Use the set (router) dns commands to set Domain Name Server (DNS) options.
set (router) dns domain
Use the set (router) dns domain command to set the default domain that the DNS resolver
will add to any name queries that are not fully qualified.
Syntax: set {rtr_card-addr} dns domain {domain-name"}
Example: set 3 dns domain "mycompany.com"
The example will set the default domain to "mycompany.com" for the Router in
slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"domain-name"}
The domain name, with a maximum of 43 characters. Name must be enclosed in quotes.
set (router) dns name
Use the set (router) dns name command to set the TSR card host name.
Syntax: set {rtr_card-addr} dns name {"host-name"}
Example: set 3 dns name "Axxius25"
The example will set the Router card host name to "Axxius25" for the Router in
slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"host-name"}
The host name for the Router card. This name must be enclosed in quotes, with a maximum
of 15 characters.
5-108
Axxius 800 - Release 2.2
CLI Commands
set
set (router) dns resolver
Use the set (router) dns resolver command to enable/disable use of DNS resolver to
convert domain names to IP addresses. The DNS server address must be set before the DNS
resolver can be enabled.
Syntax: set {rtr_card-addr} dns resolver {disable|enable}
Example: set 3 dns resolver disable
The example will disable the DNS resolver for the Router in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{disable|enable}
disable
enable
Disable DNS resolver
Enable DNS resolver
set (router) dns server
Use the set (router) dns server command to configure the IP address of DNS servers.
Syntax: set {rtr_card-addr} dns server {1|2} {ip-addr}
Example: set 3 dns server 1 10.10.10.0
The example will set the IP address of the DNS server number 1 to 10.10.10.0
for the Router in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{1|2}
1
2
Setup IP address of DNS server 1
Setup IP address of DNS server 2
{ip-addr}
The IP address, in the form of xxx.xxx.xxx.xxx, where xxx is between 0-255.
Axxius 800 - Release 2.2
5-109
CLI Commands
set
set (router) enhanced security
Use the set (router) enhanced security command to enable or disable enhanced login security
on the TSR. When enabled the user will not receive any login prompt or other output until the
security password is typed. The security password is set via the set (router) password command.
Syntax: set {rtr_card-addr} enhanced security
{disable|enable}
Example: set 5 enhanced security enable
The example will enable the enhanced security on the Router card in slot 5.
Note: A set 5 password security "password" command must be completed
before the enhanced security can be enabled.
See, set (router) password on page 5-114
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{disable|enable}
disable
enable
Disable enhanced login security
Enable enhanced login security
set (router) lmi
Use the set (router) lmi command to specify the Local Management Interface (LMI) protocol
to use for the specified Router card.
Syntax: set {rtr_card-addr} lmi {annexd|disable|lmi}
Example: set 5 lmi annexd
The example will configure LMI on the Router card in slot 5 to
Annex D.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{annexd|disable|lmi}
annexd
disable
lmi
5-110
Set LMI to Annex D.
Disable LMI on the TSR.
Set LMI to LMI rev1 (DLCI 1023)
Axxius 800 - Release 2.2
CLI Commands
set
set (router) lmi poll
Use the set (router) lmi poll command to specify the Local Management Interface (LMI) for
the specified Router card.
Syntax: set {rtr_card-addr} lmi poll {counter|interval}
{value}
Example: set 5 lmi poll counter 15
The example will configure LMI poll count to 15, on the Router card in slot 5.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{counter|interval}
counter
interval
Set the LMI count. {value} = count of how many link status enquiries can
go un-responded before the link is declared down. Range is 0-255.
Set LMI period {value} = LMI period. Range is between 0-255 seconds.
set (router) login auth
Use the set (router) login auth command to specify how login authentication for this
router should be performed. The router supports a configuration setting for each router card
to determine how the router card logins are to be authenticated, as per one of the following
choices: authenticate router logins from the router card local database (default), or
authenticate router logins identically to Controller logins. The last choice will cause the
router logins to be authenticated via the Controller’s database of users and passwords, as
configured for the Controller.
Syntax: set {rtr_card-addr} login auth
{controller|local|radius}
Example: set 1 login auth controller
The example will set the TSR card in slot 1 to use the same login setting as the
Controller.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{controller|local|radius}
controller
local
radius
Axxius 800 - Release 2.2
Use the Controller’s login auth setting
Authenticate logins locally
Authenticate logins with RADIUS server
5-111
CLI Commands
set
set (router) login prompt
Use the set (router) login prompt command to enable/disable the login prompt on the
specified Router card.
Syntax: set {rtr_card-addr} login prompt {disable|enable}
Example: set 1 login prompt enable
The example will set the Router card to require a login with Telnets from the
Controller.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{controller|local|radius}
disable
enable
Disable the login prompt
Enable the login prompt
set (router) ntp
Use the set (router) ntp command to setup Network Time Protocol (NTP) parameters.
Note: not operational in this release.
set (router) ntp enable/disable
Use the set (router) ntp enable/disable command to enable/disable NTP processing.
Syntax: set {rtr_card-addr} ntp {disable|enable}
Example: set 1 ntp enable
The example will enable NTP processing on the Router card in slot 1.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{disable|enable}
disable
enable
5-112
Disable NTP processing
Enable NTP processing
Axxius 800 - Release 2.2
CLI Commands
set
set (router) ntp poll
Use the set (router) ntp poll command to specify polling of the NTP server every defined
number of seconds. Note: not operational in this release.
Syntax: set {rtr_card-addr} ntp poll {seconds}
Example: set 1 ntp poll 120
The example will Poll the Network Time Protocol server every 2 minutes, for
the Router card in slot 1.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{seconds}
The number of seconds between polls. Seconds range is 16 to 1024. Default is 16.
set (router) ntp server
Use the set (router) ntp server command to specify the IP address of the NTP server.
Note: not operational in this release.
Syntax: set {rtr_card-addr} ntp server {ip-addr}
Example: set 1 ntp server 10.10.10.0
The example will set the address to be used to access the NTP server to
10.10.10.0, on the Router in slot 1.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{ip-addr}
The IP address of the NTP server, in the form of xxx.xxx.xxx.xxx, where xxx is between
0-255. Setting the NTP server value to 0.0.0.0 will cause the Router to listen to and
process NTP broadcasts.
Axxius 800 - Release 2.2
5-113
CLI Commands
set
set (router) ntp timezone
Use the set (router) ntp timezone command to specify the timezone offset relative to GMT
for this TSR. Note: not operational in this release.
Syntax: set {rtr_card-addr} ntp timezone {hour-offset}
[minute-offset]
Example: set 1 ntp timezone -5
The example will specify the gateway time to be 5 hours from GMT (Greenwich
Mean Time), which equates to Eastern Standard time, for the Router in slot 1.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{hour-offset}
Used to calculate gateway time from GMT. The hour-offset range is -12 to 12.
[minute-offset]
Used to calculate gateway time from GMT. The minute-offset range is 0 to 60.
set (router) password
Use the set (router) password command to manage password access on the specified Router
card.
Syntax: set {rtr_card-addr} password {setting} {"password"}
Example: set 5 password view "Fred"
The example will set the password to the view level to "Fred" on the Router card
in slot 5.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{setting}
admin
config
security
view
Set Administration level password on the Router.
Set Configuration level password on the Router.
Set Security level password on the Router.
Set View level password on the Router.
{"password"}
A password with a maximum of 15 characters. Password must be enclosed in quotes, and
is case-sensitive.
5-114
Axxius 800 - Release 2.2
CLI Commands
set
set (router) port
Use the set (router) port command to set port characteristics on a Terminal Server Router
(TSR) card.
set (router) port baudrate
Use the set (router) port baudrate command to set the baud rate on a TSR port.
Syntax: set {tsr_card-addr} port {port-number} baudrate
{value}
Example: set 5 port 2 baudrate 38400
The example will set the baud rate to 38400 on the second port on the TSR card
in slot 5.
{tsr_card-addr}
The slot number (1-8) that contains the TSR card.
{port-number}
The port number (1-4) of the TSR card.
{value}
The values listed below are the baud rates that have been tested and are selectable with the
auto-completion feature. A rate that is not listed may be manually typed in the {value}
field, range is 11 to 691200. Not all baud rates will resolve exactly, in this circumstance the
closest possible rate will be chosen and the user informed of the rate.
1200
2400
4800
9600
19200
38400
57600
115200
Set baud rate to 1200
Set baud rate to 2400
Set baud rate to 4800
Set baud rate to 9600
Set baud rate to 19200
Set baud rate to 38400
Set baud rate to 57600
Set baud rate to 115200
Axxius 800 - Release 2.2
5-115
CLI Commands
set
set (router) port databits
Use the set (router) port databits command to set the data bits on a TSR port.
Syntax: set {tsr_card-addr} port {port-number} databits
{5|6|7|8}
Example: set 5 port 2 databits 6
The example will set the data bits to 6 on the port 2 on the TSR card in slot 5.
{tsr_card-addr}
The slot number (1-8) that contains the TSR card.
{port-number}
The port number (1-4) of the TSR card.
{5|6|7|8}
Allowable data bits. Note: If 1.5 Stop Bits is selected, the Data Bits setting MUST be 5
Data Bits, if 2 Stop Bits is selected, 5 Data Bits MUST NOT be selected. See set (router)
port stopbits on page 5-122.
set (router) port dsr low reset
Use the set (router) port dsr low reset command to cause a RE-232 session to terminate
when DSR (Data Set Ready) goes low. This setting can be issued when the card is
physically strapped for Ethernet, but has not effect. This setting also only goes into effect
when the DSR signal is high. This setting can be done for any application type but is only
active for termserv and rawtcp modes.
Syntax: set {tsr_card-addr} port {port-number} dsr low reset
{disable|enable}
Example: set 5 port 2 dsr low reset enable
{tsr_card-addr}
The slot number (1-8) that contains the TSR card.
{port-number}
The port number (1-4) of the TSR card.
{disable|enable}
disable
enable
5-116
Disable will not use the reset feature. Default
Enable causes the session to teardown when DSR goes low.
Axxius 800 - Release 2.2
CLI Commands
set
set (router) port flowcontrol
Use the set (router) port flowcontrol command to set the flow control on a TSR port. This
command controls the transfer of messages or characters between two points in a data
network to prevent congestion, or loss of data when the receiving device’s buffer begins to
reach its capacity.
Syntax: set {tsr_card-addr} port {port-number} flowcontrol
{none|rtscts|xonxoff}
Example: set 5 port 2 flowcontrol none
The example will set the flowcontrol to none on the second port on the TSR card
in slot 5.
{tsr_card-addr}
The slot number (1-8) that contains the TSR card.
{port-number}
The port number (1-4) of the TSR card.
{none|rtscts|xonxoff}
none
rtscts
xonxoff
Axxius 800 - Release 2.2
Set flow control to none
Set flow control to hardware
Set flow control to xonxoff
5-117
CLI Commands
set
set (router) port inactivity timer
Use the set (router) port inactivity timer command to set the inactivity timeout for a
RS-232 session. This setting can be issued when the card is physically strapped for
Ethernet, bus has no effect. When this timer is set, the socket will be reset when no data is
sent or received on the port for the number of minutes the timer is set to. This timer can be
set for any application type, but is only active for termserv and rawtcp modes.
Syntax: set {tsr_card-addr} port {port-number} inactivity
timer {disable|time}
Example: set 5 port 2 inactivity timer 30
{tsr_card-addr}
The slot number (1-8) that contains the TSR card.
{port-number}
The port number (1-4) of the TSR card.
{disable|time}
disable
time
Disable will not use a inactivity timer. Default.
The inactivity timer will cause the session to timeout and teardown when
a value is entered. Range is 1 - 999.
set (router) port ip
Use the set (router) port ip command to set an IP address for a TSR port.
Syntax: set {tsr_card-addr} port {port-number} ip {ip-addr}
Example: set 5 port 2 ip 192.100.1.1
The example will set the IP address on the second port on the TSR card in
slot 5 to 192.100.1.1.
{tsr_card-addr}
The slot number (1-8) that contains the TSR card.
{port-number}
The port number (1-4) of the TSR card.
{ip-addr}
The IP address for the defined port, in the form of xxx.xxx.xxx.xxx, where xxx is between
0-255.
5-118
Axxius 800 - Release 2.2
CLI Commands
set
set (router) port name
Use the set (router) port name command to set define name for a TSR port.
Syntax: set {tsr_card-addr} port {port-number} name {"name"}
Example: set 5 port 2 name "portname"
The example will set a port name on the second port on the TSR card in
slot 5 to "portname".
{tsr_card-addr}
The slot number (1-8) that contains the TSR card.
{port-number}
The port number (1-4) of the TSR card.
{name}
Port identifier, with up to 15 characters, enclosed in quotes.
set (router) port parity
Use the set (router) port parity command to set the parity on a TSR port.
Syntax: set {tsr_card-addr} port {port-number} parity
{even|none|odd}
Example: set 5 port 2 parity none
The example will set the parity on the second port on the TSR card in
slot 5 to none.
{tsr_card-addr}
The slot number (1-8) that contains the TSR card.
{port-number}
The port number (1-4) of the TSR card.
{even|none|odd}
even
none
odd
Set even parity to the TSR port
Set no parity to the TSR port
Set odd parity to the TSR port
Axxius 800 - Release 2.2
5-119
CLI Commands
set
set (router) port passive
Use the set (router) port passive command to set the TSR port to passive. This command
will terminate any active telnet connection on this interface and will reinitialize its
associated TCP socket.
Syntax: set {tsr_card-addr} port {port-number} passive
Example: set 1 port 2 passive
Do you wish to do this (y/n)?
{tsr_card-addr}
The slot number (1-8) that contains the TSR card.
{port-number}
The port number (1-4) of the TSR card.
set (router) port password
Use the set (router) port password command to set the password on a TSR port.
Syntax: set {tsr_card-addr} port {port-number} password
{"password"}
Example: set 1 port 2 password "test"
This command will set the password for port 2 on the TSR card in slot 1 to "test".
{tsr_card-addr}
The slot number (1-8) that contains the TSR card.
{port-number}
The port number (1-4) of the TSR card.
{"password"}
A password with a maximum of 15 characters, enclosed in quotes.
5-120
Axxius 800 - Release 2.2
CLI Commands
set
set (router) port prompt
Use the set (router) port prompt command to set the authentication prompt on a TSR port.
Syntax: set {tsr_card-addr} port {port-number} prompt
{disable|enable}
Example: set 1 port 2 prompt enable
This command will enable the authentication prompt for port 2 on the TSR card
in slot 1.
{tsr_card-addr}
The slot number (1-8) that contains the TSR card.
{port-number}
The port number (1-4) of the TSR card.
{disable|enable}
disable
enable
Disable the Authentication Prompt on a TSR port
Set the Authentication Prompt on a TSR port
set (router) port protocolport
Use the set (router) port protocolport command to set the protocol port on a TSR port.
Syntax: set {tsr_card-addr} port {port-number} protocolport
{protocol-port}
Example: set 1 port 2 protocolport 1024
This command will set the protocol port to 1024 for port 2 on the TSR card in
slot 1.
{tsr_card-addr}
The slot number (1-8) that contains the TSR card.
{port-number}
The port number (1-4) of the TSR card.
{protocol-port}
The protocol port range is 1 - 65525. 0 is the wildcard, any port designator.
Axxius 800 - Release 2.2
5-121
CLI Commands
set
set (router) port stopbits
Use the set (router) port stopbits command to set the number of stop bits on a TSR port.
The stop bit is an interval at the end of each Asynchronous Character that allows the
receiving computer to pause before the start of the next character.
Syntax: set {tsr_card-addr} port {port-number} stopbits
{1|1.5|2}
Example: set 5 port 2 stopbits 1
The example will set the number of stop bits on the second port on the TSR card
in slot 5 to 1.
{tsr_card-addr} - The slot number (1-8) that contains the TSR card.
{port-number} - The port number (1-4) of the TSR card.
{1|1.5|2}
Stop bits values available. Note: If 1.5 Stop Bits is selected, the Data Bits setting MUST
be 5 Data Bits, if 2 Stop Bits is selected, 5 Data Bits MUST NOT be selected.
set (router) port tbos map description
Use the set (router) port tbos map description command to set a description attribute for
one of the eight available TBOS displays. This setting can be issued when the card is
physically strapped for Ethernet, but has no effect. This setting can be done for any
application type but is only used when type is set to TBOS.
Note: this command is only available on a TSR card that has TBOS feature enabled.
Syntax: set {tsr_card-addr} port {port-number} tbos map {mapaddr} description {"text-string"}
Example: set 5 port 2 tbos map 4 description "Site 7, St. Louis,
MO"
{tsr_card-addr} - The slot number (1-8) that contains the TSR card.
{port-number} - The port number (1-4) of the TSR card.
{map-addr}
One of the eight TBOS displays available for monitoring equipment. Range is 1 - 8.
{"text-string"}
The TBOS map description command assigns a text string (0 - 19 characters) to a
designated display number. Default is an empty string ("").
5-122
Axxius 800 - Release 2.2
CLI Commands
set
set (router) port tbos map display
Use the set (router) port tbos map display command to set a TBOS (Telemetry Byte
Oriented Serial) display map value for one of the eight TBOS display available for
monitoring equipment. This setting can be issued when the card is physically strapped for
Ethernet, but has no effect. This setting can be done for any application type but is only used
when type is set to TBOS.
Note: this command is only available on a TSR card that has TBOS feature enabled.
Syntax: set {tsr_card-addr} port {port-number} tbos map {mapaddr} display {device|none}
Example: set 5 port 2 tbos map 4 display lynx_ds3
{tsr_card-addr} - The slot number (1-8) that contains the TSR card.
{port-number} - The port number (1-4) of the TSR card.
{map-addr}
One of the eight TBOS displays available for monitoring equipment. Range is 1 - 8.
{device|none}
device-type
none
Axxius 800 - Release 2.2
alcatel_mdr_4000
Alcatel MDR-4000 radio for
monitoring
lynx_1_4_port_prot_sw
Proxium Lynx radio
lynx_8_port_prot_sw
Proxium Lynx radio
lynx_ds3
Proxium Lynx radio
lynx_hd_31145_10
Proxium Lynx radio
lynx_hd_31145_1f
Proxium Lynx radio
None will disable monitoring for that TBOS display.
5-123
CLI Commands
set
set (router) port type
Use the set (router) port type command to set the application being used for a RS-232
(serial) port. This setting can be issued when the card is physically strapped for Ethernet,
but has no effect. This command applies to the TSR only.
Syntax: set {tsr_card-addr} port {port-number} type
{termserv|rawtcp|tbos}
Example: set 5 port 2 type tbos
{tsr_card-addr} - The slot number (1-8) that contains the TSR card.
{port-number} - The port number (1-4) of the TSR card.
{termserv|rawtcp|tbos}
termserv
rawtcp
tbos
5-124
Terminal server. Default.
Raw TCP.
TBOS (Telemetry Byte Oriented Serial). Note: this setting
requires TBOS feature to be enabled on the TSR service card.
Contact Customer Service for information on purchasing this
software keyed feature.
Axxius 800 - Release 2.2
CLI Commands
set
set (router) ppp auth
Use the set (router) ppp auth command to configure the PPP (Point-to-Point Protocol)
authentication on the specified Router card.
set (router) ppp auth byremote protocol
Syntax: set {rtr_card-addr} ppp auth byremote protocol
{chap|none|pap}
Example: set 5 ppp auth byremote protocol none
The example will set the Router in slot 5 to not allow PPP authentication of this
Axxius by the remote PPP device.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{chap|none|pap}
chap
none
pap
Set to the CHAP protocol.
The remote PPP device cannot authenticate this Axxius (default).
Set to the PAP protocol.
set (router) ppp auth byremote secret
Syntax: set {tsr_card-addr} ppp auth byremote secret
{"password"}
Example: set 5 ppp auth byremote secret "public"
The example will set the PPP authentication secret/password for the TSR in slot
5 to "public"
Note: A set (router) ppp auth by remote protocol command must be
completed before this command can be implemented.
{tsr_card-addr}
The slot number (1-8) that contains the TSR card.
{"password"}
A password with a maximum of 15 characters, enclosed in quotes.
Axxius 800 - Release 2.2
5-125
CLI Commands
set
set (router) ppp auth byremote user
Syntax: set {rtr_card-addr} ppp auth byremote user
{profilename|"protocol-name"}
Example: set 5 ppp auth byremote user profilename
The example will set the PPP authentication user name for the Router in slot 5
to equal the profile name.
Note: A set (router) ppp auth byremote protocol command must be
completed before this command can be implemented.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{profilename|"protocol-name"}
profilename
"protocol-name"
Use the profile name as the CHAP or PAP user name.
The CHAP or PAP user name. A maximum of 16 characters,
enclosed in quotes.
set (router) ppp auth ofremote protocol
Syntax: set {rtr_card-addr} ppp auth ofremote protocol
{chap|none|pap}
Example: set 5 ppp auth ofremote protocol none
The example will set the Router in slot 5 to not allow PPP authentication of this
Axxius by the Router.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{chap|none|pap}
chap
none
pap
5-126
Set to the CHAP protocol.
The remote PPP device cannot authenticate this Axxius (default).
Set to the PAP protocol.
Axxius 800 - Release 2.2
CLI Commands
set
set (router) ppp security
Use the set (router) ppp security command to set up the local external security server, that the
Router will use to authenticate remote PPP devices.
set (router) ppp security address
Syntax: set {rtr_card-addr} ppp security address
{ip-addr}
Example: set 5 ppp security address 10.1.1.1
The example will set external security server address to 10.1.1.1, for the Router
in slot 5.
Note: A set (router) ppp security server command must be completed before
this command can be implemented.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{ip-addr}
The IP address, in the form of xxx.xxx.xxx.xxx, where xxx is between 0-255.
set (router) ppp security password
Syntax: set {rtr_card-addr} ppp security password {"password"}
Example: set 5 ppp security password "public"
The example will set the password to a local external security server to "public",
for the Router in slot 5.
Note: A set (router) ppp auth by remote protocol command must be
completed before this command can be set.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"password"}
A password with a maximum of 15 characters. Password must be enclosed in quotes.
Axxius 800 - Release 2.2
5-127
CLI Commands
set
set (router) ppp security server
Syntax: set {rtr_card-addr} ppp security server
{none|radius|tacacs}
Example: set 5 ppp security server none
The example will set the Router in slot 5 to not use an external security server
to authenticate remote PPP devices.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{none|radius|tacacs}
none
radius
tacacs
5-128
Do not use an external security server to authenticate remote PPP devices
(default).
Will set the server to use the RADIUS (Remote Authentication Dial-In
Service) protocol. RADIUS is a client/server-based authentication
software system.
Will set the server to use the TACACS+ (Terminal Access Controller
Access Control System) protocol. TACACS+ provides services of
authentication, authorization and accounting independently.
Axxius 800 - Release 2.2
CLI Commands
set
set (router) proxy
Use the set (router) proxy command to enable/disable proxy ARP mode on the Router. This
command will add an IP interface between the Controller and the Router over the backplane. In
this way the Controller can be accessed by IP hosts over the Router’s LAN/WAN interfaces
without using the Controller’s physical Ethernet interface.
Syntax: set {rtr_card-addr} proxy {disable|enable} [ip-addr]
[mask|bits]
Example: set ethernet ip address 10.0.0.1 255.0.0.0
set 3:1 ip address 192.168.100.1/24
set 3 proxy enable 192.168.100.80/24
set ip gateway 192.168.100.80
Set a Router card port to proxy ARP for the Adit 600, where the Router card is
located in slot 3. In this example the Controller is reachable at 192.168.100.80
and Router at 192.168.100.1.
Example: set ethernet ip address 10.0.0.1 255.0.0.0
set 3:1 ip address 192.168.100.1/24
set 3 proxy enable 192.168.100.80/24
set ip gateway 192.168.100.1
Set a Router card port to proxy ARP for the Adit 600, where the Router card is
located in slot 3. In this example the Controller and Router will share address
192.168.100.1 on the Router. Telnet and SNMP connections to 192.168.100.1
will connect to the Controller.
{rtr_card-addr}
The slot number (1-8) that contains the Router (TSR) card.
{disable|enable}
When proxy ARP is enabled the Router will allow both the Router and Controller to be
accessed from the Router LAN and WAN interfaces.
{ip-addr}
Set the IP address for the proxy interface on the Adit 600, using the form xxx.xxx.xxx.xxx,
where xxx is a number from 0 to 255.
[mask|bits]
mask
bits
Set the subnet mask, using the form xxx.xxx.xxx.xxx, where xxx is a number
from 0 to 255. This is an optional setting.
Use this field to identify the number of bits, from left to right that will be used
to match the IP Address field within the data packet. Range is between 1-32.
Axxius 800 - Release 2.2
5-129
CLI Commands
set
There are numerous cases of IP address assignments for the proxy and each
case causes slightly different behavior:
Proxy address is in the same subnet as the Controller LAN address. If the
Controller Ethernet IP address and the proxy IP address are in the same subnet, either
since both addresses are the same or they fall into the same subnet based on address
and mask, the Controller will attempt to use the Ethernet interface to send packets to
other hosts in that subnet. Once an external host has sent a packet to the Controller that
arrives on the proxy interface, the Controller will then use the proxy interface for all
communication to that host.
Proxy address is in a different subnet than the Controller LAN address. If the
Controller Ethernet IP address and the proxy IP address are in different subnets based
on address and mask, then the Controller will use either the Ethernet interface or proxy
interface to send packets to other hosts, based on which subnet the host is in or, which
subnet the IP gateway is on.
Proxy address is equal to one of the Router’s numbered IP addresses. If the
Controller proxy IP address is equal to one of the Router’s own numbered IP addresses
or equal to one of the Router’s static NAT addresses that maps to one of the Router’s
numbered IP addresses, then the Controller and Router will appear to be a single IP
host to devices on any of the Router’s interfaces.
This is a very useful mode that will make the Controller and Router appear to be a
single IP device. When working in this mode, all management traffic directed to the
Router will be forwarded internally to the Controller instead. This includes Telnet,
SNMP, Adit-Navigator socket applications. When configured this way, an external
host Telnet to the Router will go to the Controller login prompt and CLI.
If the proxy interface is to be the primary IP interface between the Controller and other
hosts, then it is highly recommended that the IP gateway be set to the same address as the
proxy address. This will make the proxy interface the default route for IP datagrams.
It is highly recommended for optimum connectability, that the Controller’s proxy IP
address be a unique host address in one of the Router subnets or be equal to one of the
Router IP addresses if the user wishes to have both devices share a single IP address, and
that the IP gateway address be set to equal the proxy address.
5-130
Axxius 800 - Release 2.2
CLI Commands
set
set (router) reboot
Use the set (router) reboot command to set automatic reboot after an upload of code or
configuration file.
Syntax: set {rtr_card-addr} reboot {code|config}
{disable|enable}
Example: set 5 reboot both disable
Disable automatic reboot after upload for the Router in slot 5.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{code|config}
code
config
Automatic reboot after code upload
Automatic reboot after configuration upload
{disable|enable}
disable
enable
Will disable automatic reboot
Will enable the automatic reboot after upload of a file
set (router) rip
Use the set (router) rip command to specify RIP packets to transmit and receive.
Syntax: set {rtr_card-addr} rip {recv|send} {v1|v2|v1and2}
Example: set 3 rip recv v1
The example will configure receive RIP on the Router card in slot 3 to V1.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{recv|send}
recv
send
Set RIP receive version
Set RIP send version
{v1|v2|v1and2}
v1
v2
v1and2
Axxius 800 - Release 2.2
Set RIP to version 1
Set RIP to version 2
Set RIP to version 1 and version 2
5-131
CLI Commands
set
set (router) snmp
Use the set (router) snmp command to set the SNMP contact, location and name on the
specified Router card.
set (router) snmp contact
Use the set (router) snmp contact command to set the value of sysContact on the specified
Router card.
Syntax: set {rtr_card-addr} snmp contact
{"contact-name"}
Example: set 1 snmp contact "John Doe"
The example will set the value of sysContact on the Router card in slot 1 to "John
Doe".
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"contact-name"}
The value of sysContact, with a maximum of 64 ASCII characters. Name must be enclosed
in quotes.
set (router) snmp location
Use the set (router) snmp location command to set the value of sysLocation on the
specified Router card.
Syntax: set {rtr_card-addr} snmp location
{"location-name"}
Example: set 1 snmp location "Newark"
The example will set the value of sysLocation on the Router card in slot 1 to
"Newark".
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"location-name"}
The value of sysLocation, with a maximum of 64 ASCII characters. Name must be
enclosed in quotes.
5-132
Axxius 800 - Release 2.2
CLI Commands
set
set (router) snmp name
Use the set (router) snmp name command to set the value of sysName on the specified
Router card.
Syntax: set {rtr_card-addr} snmp name {"system-name"}
Example: set 1 snmp name "AxxiusRouters"
The example will set the value of sysName on the TSR card in slot 1 to
"AxxiusRouters".
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"system-name"}
The value of sysName, with a maximum of 64 ASCII characters. Name must be enclosed
in quotes.
Axxius 800 - Release 2.2
5-133
CLI Commands
set
set (router) stp
Use the set (router) stp commands to configure the Spanning Tree Protocol on the Router.
Note: Enter {slot} only, if {slot:port} is entered the command will be directed to the Router
LAN and not the Router Card.
set (router) stp bridge forwarddelay
Use the set (router) stp bridge forwarddelay command to configure Spanning Tree
bridge forward delay value for the bridge. The bridge forward delay is the time spent by a
Port in the Listening or Learning States before the transitioning to the Learning or
Forwarding State, respectively.
Syntax: set {rtr_card-addr} stp bridge forwarddelay {value}
Example: set 3 stp bridge forwarddelay 15
The example will set the Spanning Tree bridge forward delay time to 15
seconds, on the Router in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{value}
The value can range from 4 to 30 seconds, with a default of 15.
set (router) stp bridge hellotime
Use the set (router) stp bridge hellotime command to configure Spanning Tree bridge
hello time value for the bridge.
Syntax: set {rtr_card-addr} stp hellotime {value}
Example: set 3 stp bridge hellotime 3
The example will set the Spanning Tree bridge hello time to 3 seconds, on the
Router in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{value}
The value can range from 1 to 10 seconds, with a default of 2.
5-134
Axxius 800 - Release 2.2
CLI Commands
set
set (router) stp bridge maxage
Use the set (router) stp bridge maxage command to configure Spanning Tree maximum
age value for the bridge. The bridge max age value specifies the maximum age of received
protocol information before it is discarded.
Syntax: set {rtr_card-addr} stp maxage {value}
Example: set 3 stp bridge maxage 15
The example will set the Spanning Tree bridge max age to 15 seconds, on the
Router in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{value}
The value can range from 6 to 40 seconds, with a default of 20.
set (router) stp bridge priority
Use the set (router) stp bridge priority command to configure Spanning Tree priority
value for the bridge.
Syntax: set {rtr_card-addr} stp priority {value}
Example: set 3 stp bridge priority 32768
The example will set the Spanning Tree bridge priority to 32768, on the Router
in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{value}
The value can range from 0 to 65535, with a default of 32768.
Axxius 800 - Release 2.2
5-135
CLI Commands
set
set (router) stp enable/disable
Use the set (router) stp enable/disable command to enable and disable Spanning Tree
Protocol on the Router.
Syntax: set {rtr_card-addr} stp {disable|enable}
Example: set 3 stp enable
The example will enable Spanning Tree on the Router in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
Note: Enter {slot} only. If {slot:port} is entered the command will be directed to the
Router LAN and not the Router Card.
{disable|enable}
disable
enable
5-136
Disable Spanning Tree protocol
Enable Spanning Tree protocol
Axxius 800 - Release 2.2
CLI Commands
set
set (router) syslog
Use the set (router) syslog commands to configure the Router to send alarm and event
messages to a Syslog server.
set (router) syslog enable/disable
Use the set (router) syslog enable/disable command to enable and disable sending alarm
and event messages to an external Syslog server from the Router.
Syntax: set {rtr-addr} syslog {disable|enable}
Example: set 3 syslog enable
The example will enable alarms and event messages to the external Syslog
server, on the Router card in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{disable|enable}
disable
enable
Disable Syslog protocol
Enable Syslog protocol
set (router) syslog facility
Use the set (router) syslog facility command to set the Syslog facility value that the Router
card will report to a syslog server in each message.
Syntax: set {rtr_card-addr} syslog facility {value}
Example: set 3 syslog facility 16
The example will set the Syslog facility value to 16, on the Router in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{value}
The range of valid facility values is from 0 to 23, with a default of 16 (local use 0).
Axxius 800 - Release 2.2
5-137
CLI Commands
set
set (router) syslog level
Use the set (router) syslog level command to set the Syslog severity level. Events of all
severity levels lower in number (more severe) will be sent to the Syslog server.
Syntax: set {rtr_card-addr} syslog level {severity}
Example: set 3 syslog level 4
The example will set the Syslog severity level to 4, on the Router card in
slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{severity}
The severity threshold level can range from 0 to 7.
set (router) syslog server
Use the set (router) syslog server command to set the IP address of an external Syslog
server.
Syntax: set {rtr_card-addr} syslog server {ip-addr}
Example: set 3 syslog server 10.0.0.1
The example will set the external Syslog server IP address to 10.0.0.1, on the
Router card in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{ip-addr}
Set the IP address for the external Syslog server, using the form xxx.xxx.xxx.xxx, where
xxx is a number from 0 to 255.
5-138
Axxius 800 - Release 2.2
CLI Commands
set
set (router-lan) filter forward
Use the set (router-lan) filter forward command to specify the forwarding mode for Layer 2
filters on the LAN interface.
Syntax: set {rtr_lan-addr} filter forward
{matching|nontmatching}
Example: set 3:1 filter forward notmatching
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{matching|nontmatching}
matching
notmatching
Axxius 800 - Release 2.2
Only those frames matching a rule will be forwarded.
Only those frames NOT matching a rule will be forwarded.
5-139
CLI Commands
set
set (router-lan) framing
Use the set (router-lan) framing command to specify which Ethernet frame types are
supported on the LAN interface.
Syntax: set {rtr_lan-addr} framing {ipx|other}
{ieee8022|ieee8023|ethii|snap} {disable|enable}
Example: set 3:1 framing ipx ieee8022 enable
The example will enable the 802.2 frame type for IPX packets on the LAN of
the Router card in slot 3.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{ipx|other}
ipx
other
Enable or disable a frame type for the IPX protocol
Enable or disable a frame type for protocols other than IP and IPX
{ieee8022|ieee8023|ethii|snap}
ethii
ieee8022
ieee8023
snap
Ethernet II framing
IEEE 802.2 framing
IEEE 802.3 framing
LLC/SNAP framing
{disable|enable}
disable
enable
5-140
Disable the frame type
Enable the frame type
Axxius 800 - Release 2.2
CLI Commands
set
set (router-lan) gateway
Use the set (router-lan) gateway command to specify a default IP gateway for the specified
LAN interface. If there is no static network entry to 0.0.0.0, then this address is used as the
default gateway for packets with no explicit route.
Syntax: set {rtr_lan-addr} gateway {ip-addr}
Example: set 3:1 gateway 192.168.201.144
The example will set the local LAN interface on slot 3 to use a default gateway
at IP address 192.168.201.144.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{ip-addr}
The IP address of the gateway, in the form of xxx.xxx.xxx.xxx, where xxx is between
0-255.
Axxius 800 - Release 2.2
5-141
CLI Commands
set
set (router-lan) ip address
Use the set (router-lan) ip address command to specify an IP address for the specified LAN
interface. When first installed the Router card’s LAN interface has a default IP address of
10.0.0.1 with subnet mask of 255.0.0.0.
Syntax: set {rtr_lan-addr} ip address {ip-addr} [mask]
Example: set 3:1 ip address 192.168.202.244 255.255.255.0
The example will set the local LAN interface on slot 3 to IP address
192.168.202.244, with a subnet mask of 255.255.255.0.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{ip-addr}
The Router IP address, in the form of xxx.xxx.xxx.xxx, where xxx is between
0-255.
[mask]
The subnet mask, in the form of xxx.xxx.xxx.xxx, where xxx is between 0-255.
5-142
Axxius 800 - Release 2.2
CLI Commands
set
set (router-lan) ipx network
Use the set (router-lan) ipx network command to specify IPX network numbers for the four
IPX LAN frame types. This enables the Axxius to Router IPX to Remote (WAN) networks,
even if an IPX server does not exist on the local LAN. Typically, the Axxius will learn its
external network number. However, if the local LAN does not have a server or if the IPX RIP
setting is set to <Neither>, and you wish to Router IPX to Remote (WAN) networks, the
external network number must be defined.
Syntax: set {rtr_lan-addr} ipx network
{ieee8022|ieee8023|ethii|snap} {network}
Example: set 3:1 ipx network ieee8022 000000fl
The example will set the local LAN interface on slot 3 to IP address
192.168.202.244, with a subnet mask of 255.255.255.0.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{ieee8022|ieee8023|ethii|snap}
ethii
ieee8022
ieee8023
snap
Ethernet II framing
IEEE 802.2 framing
IEEE 802.3 framing
LLC/SNAP framing
{network}
External IPX network, specified as an 8-digit hexadecimal number.
Axxius 800 - Release 2.2
5-143
CLI Commands
set
set (router-lan) phy
Use the set (router-lan) phy command to specify the Ethernet PHY (physical specifications)
speed and mode.
NOTE: It is highly recommended that this setting be left at autonegotiation. Connecting Ethernet devices with incompatible setting can
lead to severe network performance degradation, increased collisions, late
collisions, CRC errors, and undetected data corruption.
Syntax: set {rtr_lan-addr} phy {setting}
Example: set 3:1 phy full100
The example will force the Ethernet PHY to 100 MHz full-duplex on the Router
in slot 3.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{setting}
auto
full10
full100
half10
half100
5-144
Auto-negotiate (highly recommended).
10 MHz full-duplex.
100 MHz full-duplex.
10 MHz half-duplex.
100 MHz half-duplex.
Axxius 800 - Release 2.2
CLI Commands
set
set (router-lan) rip
Use the set (router-lan) rip commands to specify RIP for the specified LAN interface.
set (router-lan) rip ip
Use the set (router-lan) rip ip command to specify the IP RIP for the specified LAN
interface.
Syntax: set {rtr_lan-addr} rip ip {both|neither|recv|send}
Example: set 2:1 rip ip send
The example will set RIP on the local LAN interface on slot 2 to send.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{both|neither|recv|send}
both
neither
recv
send
Axxius 800 - Release 2.2
Enable IP RIP (or IPX RIP and SAP) in both directions.
Shut IP RIP (or IPX RIP and SAP) off completely.
Enable IP RIP (or IPX RIP and SAP) in the receive direction only.
Enable IP RIP (or IPX RIP and SAP) in the send direction.
5-145
CLI Commands
set
set (router-lan) rip ipx
Use the set (router-lan) rip ipx command to specify the IPX RIP and SAP for the specified
LAN interface.
Syntax: set {rtr_lan-addr} rip ipx {both|neither|recv|send}
Example: set 2:1 rip ipx send
The example will set RIP and SAP on the local LAN interface on slot 2 to send.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{both|neither|recv|send}
both
neither
recv
send
5-146
Enable IPX RIP (or IPX RIP and SAP) in both directions.
Shut IPX RIP (or IPX RIP and SAP) off completely.
Enable IPX RIP (or IPX RIP and SAP) in the receive direction
only.
Enable IPX RIP (or IPX RIP and SAP) in the send direction.
Axxius 800 - Release 2.2
CLI Commands
set
set (router-lan) stp
Use the set (router-lan) stp commands to configure the Spanning Tree Protocol on this
interface.
set (router-lan) stp enable/disable
Use the set (router-lan) stp enable/disable command to enable/disable Spanning Tree
Protocol on this interface. To enable STP on an interface it must be enabled globally with
the set (router) stp enable command.
Syntax: set {rtr_lan-addr} stp {disable|enable}
Example: set 3:1 stp enable
The example will enable Spanning Tree on the LAN for this interface.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{disable|enable}
disable
enable
Axxius 800 - Release 2.2
Disable Spanning Tree on this interface.
Enable Spanning Tree on this interface.
5-147
CLI Commands
set
set (router-lan) stp port cost
Use the set (router-lan) stp port cost command to configure Spanning Tree path cost
value for this bridge port.
Syntax: set {rtr_lan-addr} stp port cost {port-cost-value}
Example: set 3:1 stp port cost 100
Sets the Spanning Tree port cost value at 100, on the Router in slot 3.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
Slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{port-cost-value}
The value can range from 1 to 65535, higher values represent slower data paths. For a 100
Mb LAN a value of 19 is recommended. For a 10 Mb LAN a value of 100 is recommended.
set (router-lan) stp port priority
Use the set (router-lan) stp port priority command to configure Spanning Tree priority
value for this bridge port.
Syntax: set {rtr_lan-addr} port priority
{port-priority-value}
Example: set 3:1 stp port priority 128
The example will set the STP port priority to 128, on the Router in slot 3.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
Slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{port-priority-value}
Spanning Tree port priority for this bridge port. Range from 0 to 255, with a default of 128.
5-148
Axxius 800 - Release 2.2
CLI Commands
set
set (router-lan) up/down
Use the set (router-lan) up/down command to set the specified LAN interface up or down.
When the Router port is set down, a link failure will not cause an alarm. This can be used to
eliminate alarms from Router ports that are not in-use. When the Router port is set up, a link
failure on the Ethernet port will cause an alarm to be reported to the Axxius 800.
Syntax: set {rtr_lan-addr} {down|up}
Example: set 2:1 down
The example will set the local LAN interface on slot 2 down.
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
Slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
{down|up}
down
up
Axxius 800 - Release 2.2
Set the Router as Out-of-Service. This command turns off the LED and
disables alarm reporting for the Router specified.
Set the Router as In-Service. This command turns on the LED and
enables alarm reporting for the Router specified.
5-149
CLI Commands
set
set (router-trunk) encapsulation
Use the set (router-trunk) encapsulation command to specify the encapsulation to use on the
TSR interface.
Syntax: set {rtr_trunk-addr} encapsulation {setting}
Example: set 2:1:5 encapsulation pppofr
The example will configure encapsulation on the Router card in slot 2, port 1,
trunk 5 to PPP over.
{rtr-trunk-addr}
slot
port
trunk
Slot number (1-8) that contains the Router card
Port number of the Router
Trunk number for this port, 1-24
{setting}
fr
ppp
pppofr
Frame Relay as per RFC 2427
Point-to-Point Protocol (PPP) as per RFC 1661 and 1662
PPP over Frame Relay as per RFC 1973
set (router-trunk) multilink group
Use the set (router-trunk) multilink group command to specify a Router trunk to be part of a
multilink PPP group. Note: It is recommended, for performance, that all of the individual links
in the multilink group have approximately the same bandwidth.
Syntax: set {rtr-trunk-addr} multilink group {number}
Example: set 3:1:1-2 multilink group 1
The example will form a multilink PPP group that combines trunk 1 and 2.
set 3:1:3 multilink group
The example will add a third trunk to the multilink PPP group from above.
{rtr-trunk-addr}
slot
port
trunk
Slot number (1-8) that contains the Router card
Port number of the Router
Trunk number for this port, 1-24
{number}
The multilink group number. Range is 1-24.
5-150
Axxius 800 - Release 2.2
CLI Commands
set
set (router-trunk) speed
Use the set (router-trunk) speed command to specify the data speed for each DS0 in the
given trunk. This command takes effect upon transition of the trunk to active. This
command applies to the TSR card only.
Syntax: set {tsr-trunk-addr} speed {56|64}
Example: set 3:1:23 speed 56
The example will set the data speed of trunk 23 in the TSR in slot 3 to 56 Kbps.
{tsr-trunk-addr}
slot
port
trunk
Slot number (1-8) that contains the TSR card
Port number of the Router
Trunk number for this port, 1-24
{56|64}
56
64
56 Kbps data speed
64 Kbps data speed. 64 is the default.
set (router-trunk) up/down
Use the set (router-trunk) up/down command to set the WAN trunk up or down. When the
Router trunk is set down a link failure will not cause an alarm. This can be used to eliminate
alarms from Router trunks that are not in-use. When the Router trunk is set up, a link failure on
the WAN trunk will cause an alarm to be reported to the Axxius.
Syntax: set {rtr_trunk-addr} {down|up}
Example: set 2:1:1 down
The example will set the first Router trunk interface on slot 2 down.
{rtr-trunk-addr}
slot
port
trunk
Slot number (1-8) that contains the Router card
Port number of the Router
Trunk number for this port, 1-24
{up|down}
down
up
Axxius 800 - Release 2.2
Set the WAN down.
Set the WAN up.
5-151
CLI Commands
set
set (router-wan) dlci
Use the set (router-wan) dlci command to set the DLCI (Data Link Connection Identifier) for
a specified WAN interface.
Syntax: set {rtr_card-addr} {"wan-name"} dlci {value}
Example: set 1 "LosAngeles" dlci 16
The example will set the WAN interface named "LosAngeles" on the Router
card in slot 1 to use DLCI value 16.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{value}
DLCI value to use, 16-1022
5-152
Axxius 800 - Release 2.2
CLI Commands
set
set (router-wan) gre
Use the set (router-wan) gre command to configure Generic Routing Encapsulation tunneling
for a specified WAN interface.
set (router-wan) gre address
Use the set (router-wan) gre address command to configure the IP addresses for GRE
tunneling for a specified WAN interface.
Syntax: set {rtr_card-addr} {"wan-name"} gre address
{local_ip-addr} [remote-ip-addr] ["tunnel-name"]
Example: set 3 "LosAngeles" gre address 10.0.0.0 20.0.0.0
"LATunnel"
The example will set the WAN interface named "LosAngeles" to the IP
addresses to be 10.0.0.0 and 20.0.0.0.
Note: A set 3 "LosAngeles" gre ip all command is required before this
command.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{local-ip-addr}
The IP Address of the local end of the tunnel, in the form of xxx.xxx.xxx.xxx, where xxx
is between 0-255.
[remote-ip-addr]
The IP Address of the far end of the tunnel, required if GRE tunneling is set to All,
prohibited if GRE tunneling is set to By Network. In the form of xxx.xxx.xxx.xxx, where
xxx is between 0-255.
["tunnel-name"]
A symbolic name to give to this tunnel, required if GRE tunneling is set to All, prohibited
if GRE tunneling is set to By Network. Up to 12 characters, enclosed in quotes.
Axxius 800 - Release 2.2
5-153
CLI Commands
set
set (router-wan) gre ip
Use the set (router-wan) gre ip command to configure the GRE tunneling of the IP
protocol for a specified WAN interface.
Syntax: set {rtr_card-addr} {"wan-name"} gre ip
{all|bynetwork|disable}
Example: set 3 "LosAngeles" gre ip all
The example will set the WAN interface "LosAngeles" in slot 3, to pass all
packets through a GRE tunnel.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{all|bynetwork|disable}
all
bynetwork
disable
Tunnel all packets on this interface to the tunnel destination address.
Tunnel packets based on their destination address by matching GRE
network entries, see add (router-wan) gre network command.
Disable GRE tunneling.
set (router-wan) gre ipx
Use the set (router-wan) gre ipx command to configure the GRE tunneling of the IPX
protocol for a specified WAN interface.
Syntax: set {rtr_card-addr} {"wan-name"} gre ipx {all|disable}
Example: set 3 "LosAngeles" gre ipx all
The example will set the WAN interface named "LosAngeles" in slot 3, to pass
all IPX packets through a GRE tunnel.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{all|disable}
all
disable
5-154
Tunnel all packets on this interface to the tunnel destination address.
Disable GRE tunneling.
Axxius 800 - Release 2.2
CLI Commands
set
set (router-wan) ip
Use the set (router-wan) ip command to set the IP traffic handling on the WAN interface.
Syntax: set {rtr_card-addr} {"wan-name"} ip
{block|bridge|route}
Example: set 1 "LosAngeles" ip route
Sets the WAN interface named "LosAngeles" on the Router in slot 1 to route IP.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{block|bridge|route}
block
bridge
route
Set the WAN to block IP.
Set the WAN to bridge IP.
Set the WAN to route IP.
set (router-wan) ip address
Use the set (router-wan) ip address command to set the IP address for a WAN interface.
Syntax: set {rtr_card-addr} {"wan-name"} ip address
{ip-addr} [mask]|unnumbered}
Example: set 1 "LosAngeles" ip address 100.2.2.2 255.255.255.0
The example will set the WAN interface named "LosAngeles" on the Router in
slot 1 to the IP address 100.2.2.2, with a subnet mask of 255.255.255.0.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{ip-addr}
Router IP address, in the form of xxx.xxx.xxx.xxx, where xxx is between 0-255.
[mask]
The subnet mask, in the form of xxx.xxx.xxx.xxx, where xxx is between 0-255.
{unnumbered}
Treat this as an un-numbered interface, as per RFC 1812.
Axxius 800 - Release 2.2
5-155
CLI Commands
set
set (router-wan) ipx
Use the set (router-wan) ipx command to set the IPX traffic handling on the specified WAN
interface.
Syntax: set {rtr_card-addr} {"wan-name"} ipx {setting}
Example: set 1 "LosAngeles" ipx bridge
The example will set the WAN interface named "LosAngeles" in slot 1, to
bridge IPX.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{setting}
block
bridge
optimize
Set the WAN to block IPX.
Set the WAN to bridge IPX with optimized local advertising IPX
servers and networks.
Set the WAN to bridge IPX with optimized local advertising of
IPX servers and networks.
Setting to optimize enables the Axxius to use Carrier Access’
network optimization feature, which ensures that only necessary
data is transmitted over the WAN connection. The Axxius will
initiate IPX learning mode. Learning mode is effective for
optimizing bandwidth usage for IPX RIP, SAP, serialization and
watchdog (IPX and SPX) packets. If you choose this option, the
Axxius will initiate learning mode in order to gain knowledge of
local and remote networks and services. Once it knows of remote
networks and services, it can advertise the information on the local
LAN on behalf of the remote networks and servers.
5-156
Axxius 800 - Release 2.2
CLI Commands
set
set (router-wan) nat
Use the set (router-wan) nat commands to configure Network Address Translation (NAT) on
a specified WAN interface.
set (router-wan) nat address
Use the set (router-wan) nat address command to configure Network Address
Translation (NAT) public addresses for a specified WAN interface.
Syntax: set {rtr_card-addr} {"wan-name"} nat address
{assigned|ip-addr} [count]
Example: set 1 "LosAngeles" nat address 201.17.172.11 8
The example will set the WAN interface named "LosAngeles" on the Router in
slot 1 to perform NAT translation to one of 8 public address from 201.17.172.11
to 201.17.172.19.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{assigned|ip-addr}
assigned
ip-addr
The NAT address assigned by remote.
The Router IP address, in the form of xxx.xxx.xxx.xxx, where xxx
is between 0-255.
[count]
An optional field defining the number of public addresses in the NAT pool. Default is 1
Axxius 800 - Release 2.2
5-157
CLI Commands
set
set (router-wan) nat enable/disable
Use the set (router-wan) nat command to enable and disable Network Address Translation
(NAT) on a specified WAN interface.
Syntax: set {rtr_card-addr} {"wan-name"} nat {disable|enable}
Example: set 1 "LosAngeles" nat enable
The example will set the WAN interface named "LosAngeles" on the Router
card in slot 1 to enable NAT mapping.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{disable|enable}
disable
enable
Disable NAT mapping.
Enable NAT mapping.
set (router-wan) nat ports
Use the set (router-wan) nat ports command to configure Network Address Translation
(NAT) to dynamically map ports or preserve them. This field should only be set to
"preserved" if an application that you are using requires a specific port number.
Syntax: set {rtr_card-addr} {"wan-name"} nat ports
{dynamic|preserved}
Example: set 1 "LosAngeles" nat ports dynamic
The example will set the WAN interface named "LosAngeles" on the Router
card in slot 1 to enable dynamic NAT port mapping.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{dynamic|preserved}
dynamic
preserved
5-158
Set NAT port mapping to be dynamic.
Preserve original port.
Axxius 800 - Release 2.2
CLI Commands
set
set (router-wan) other
Use the set (router-wan) other command to set the traffic handling of protocols other than IP
or IPX on the specified WAN interface.
Syntax: set {rtr_card-addr} {"wan-name"} other {block|bridge}
Example: set 1 "LosAngeles" other bridge
The example will set the WAN interface named "LosAngeles" in slot 1, to
bridge other protocols.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{block|bridge}
block
bridge
Axxius 800 - Release 2.2
Set the WAN to block protocols other than IP or IPX.
Set the WAN to bridge protocols other than IP or IPX.
5-159
CLI Commands
set
set (router-wan) ppp
Use the set (router) ppp command to configure the PPP (Point-to-Point Protocol) on the
specified Router card.
set (router-wan) ppp auth ofremote user
Use the set (router-wan) ppp auth ofremote user command to set the CHAP or PAP
name by which a remote PPP device is authenticated by this Axxius.
Syntax: set {rtr_card-addr} {"wan-name"} ppp auth ofremote
user {profilename|"protocol-name"}
Example: set 5 "LosAngeles" ppp auth ofremote user profilename
The example will set the PPP authentication user name for the WAN interface
named "LosAngeles" tin slot 1 to equal the profile name.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{profilename|"protocol-name"}
profilename
"protocol-name"
5-160
Use the profile name as the CHAP or PAP user name.
CHAP or PAP user name. Up to 16 characters, enclosed in quotes.
Axxius 800 - Release 2.2
CLI Commands
set
set (router-wan) ppp compression
Use the set (router-wan) ppp compression command to configure the PPP compression
with the remote PPP device.
Syntax: set {rtr_card-addr} {"wan-name"} ppp compression
{setting}
Example: set 5 "LosAngeles" ppp compression enable
The example will set PPP to attempt to negotiate PPP compression on the WAN
interface named "LosAngeles" in slot 1.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{setting}
disable
easy
enable
hard
Disable PPP compression negotiation (default).
Typical data on this interface is easy to compress, such as text files (default).
Enable PPP compression negotiation.
Typical data on this interface is hard to compress, such as binary files.
set (router-wan) ppp security server
Use the set (router-wan) ppp security server command to set the security server with the
remote PPP device.
Syntax: set {rtr_card-addr} {"wan-name"} ppp security server
{external|local}
Example: set 5 "LosAngeles" ppp security server local
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{external|local}
external
local
Axxius 800 - Release 2.2
PPP External Security Server
PPP Local Security Server
5-161
CLI Commands
set
set (router-wan) rip
Use the set (router-wan) rip commands to set the type of RIP updates on the WAN interface.
set (router-wan) rip ip updates
Use the set (router-wan) rip ip updates command to set the type of RIP updates on the
specified WAN interface.
Syntax: set {rtr_card-addr} {"wan-name"} rip ip updates
{never|periodic|triggered}
Example: set 1 "LosAngeles" rip ip updates never
The example will set the WAN interface named "LosAngeles" on the Router
card in slot 1 to not sent RIP updates.
{rtr_card-addr} - The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{setting}
never
periodic
triggered
Set the WAN to not send RIP updates.
Set the WAN to send periodic RIP updates.
Set the WAN to send triggered RIP updates.
set (router-wan) rip ipx updates
Use the set (router-wan) rip ipx updates command to set the type of IPX RIP updates on
the specified WAN interface.
Syntax: set {rtr_card-addr} {"wan-name"} rip ipx updates
{never|periodic|triggered}
Example: set 1 "LosAngeles" rip ipx updates never
Sets the WAN interface "LosAngeles" to not sent RIP updates.
{rtr_card-addr} - The slot number (1-8) that contains the TSR card.
{"wan-name"} - The WAN interface to modify. The name must be enclosed in quotes.
{setting}
never
periodic
triggered
5-162
Set the WAN to not send RIP updates.
Set the WAN to send periodic RIP updates.
Set the WAN to send triggered RIP updates.
Axxius 800 - Release 2.2
CLI Commands
set
set (router-wan) stp
Use the set (router-wan) stp commands to configure the Spanning Tree Protocol on the
specified WAN interface.
set (router-wan) stp enable/disable
Use the set (router-wan) stp enable/disable command to enable and disable Spanning
Tree Protocol on this interface. To enable Spanning Tree on an interface it must first be
enabled globally with the set (router) stp enable command and the WAN must be set to
bridge the IP protocol.
Syntax: set {rtr_card-addr} {"wan-name"} stp {disable|enable}
Example: set 3 stp enable
The example will enable Spanning Tree on this interface.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{disable|enable}
disable
enable
Axxius 800 - Release 2.2
Disable Spanning Tree on this interface.
Enable Spanning Tree on this interface.
5-163
CLI Commands
set
set (router-wan) stp port cost
Use the set (router-wan) stp port cost command to configure Spanning Tree path cost
value for this bridge port.
Syntax: set {rtr_card-addr} {"wan-name"} stp port cost
{port-cost-value}
Example: set 3 stp port cost 650
The example sets the Spanning Tree port cost value at 650, on the Router card
in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{port-cost-value}
The value can range from 1 to 65535, with higher values representing slower data paths. A
value of 15625/# of DS0s is recommended.
set (router-wan) stp port priority
Use the set (router-wan) stp port priority command to configure Spanning Tree priority
value for this bridge port.
Syntax: set {rtr_card-addr} {"wan-name"} port priority
{port-priority-value}
Example: set 3 stp port priority 128
The example sets the Spanning Tree port priority to 128, on the Router in slot 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{port-priority-value}
The value can range from 0 to 255 seconds, with a default of 128.
5-164
Axxius 800 - Release 2.2
CLI Commands
set
set (router-wan) trunk
Use the set (router-wan) trunk command to configure the trunk port or multilink group for a
specified WAN interface. If the trunk encapsulation is subsequently changed, this trunk
assignment is reset to 0.
Syntax: set {rtr_card-addr} {"wan-name"} trunk
[multilink-group] {number}
Example: set 1 "LosAngeles" trunk 3
The example will set the WAN interface named "LosAngeles" on the Router
card in slot 1 to be mapped to trunk 3.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
[multilink-group]
This optional parameter, indicates that the number is the multilink group to use, else the
number is the trunk number to use.
{number} - Number of the trunk or multilink group to use, range is 1-24.
set (router-wan) up/down
Use the set (router-wan) up/down command to set the specified WAN interface up or down.
Syntax: set {rtr_card-addr} {"wan-name"} {down|up}
Example: set 1 "LosAngeles" up
The example will enable the WAN interface named "LosAngeles" on the Router
card in slot 1.
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
{down|up}
down
up
Axxius 800 - Release 2.2
Set the Router WAN to disabled.
Set the Router WAN to enabled.
5-165
CLI Commands
set
set screen
Use the set screen command to set the height of the scrolling output screen, in number of lines.
For example, if the screen height is set to 40 lines, the Command Line Interface (CLI) will print
the maximum of 40 lines of a long output before pausing. To set the screen to scroll without
pausing, set the screen height to 0.
Syntax: set screen {screen-height|off}
Where screen-height is the number of lines in the scrolling output screen.
5-166
Axxius 800 - Release 2.2
CLI Commands
set
set snmp
Use the set snmp command to set the Simple Network Management Protocol (SNMP) MIB-II
System Group objects.
Syntax: set snmp {setting} {"string"}
Where {setting} is as below, and {string} is its value.
Example: set snmp name "Axxius 1"
To set the SNMP system name to "Axxius 1"
Example: set snmp nms 2 192.168.3.50
Set the second SNMP NMS IP address to 192.168.3.50
{setting}
Set the values for any of the following SNMP MIB-II System Group object
contact {string}
getcom {string}
location {string}
name {string}
nms {n}
{ip-addr|none}
setcom {string}
trapauth
{disable|enable}
trapcom {string}
trapevent {setting}
trapvers {1|2}
Axxius 800 - Release 2.2
SysContact. 1 - 255 characters, enclosed in quotes
SNMP Get-Community. 1 - 32 characters, enclosed in quotes
SysLocation. 1 - 255 characters, enclosed in quotes
Set the value of the SysName (name enclosed by quotes).
Set the IP address of the SNMP manager where the SNMP agent
will send traps (up to 3 NMS addresses). The {n} is a number
from 1 to 3, to differentiate your NMS addresses.
none = no address set.
Set the value of the SNMP Set-Community string.
Enable or disable authentication traps.
Set the value for the SNMP Trap-Community string. 1 - 32
characters, enclosed in quotes
Set minimum severity level for (enterprise) event trap generation.
all
Set event trap severity limit to ’all’.
critical
Set event trap severity limit to ’critical’.
major
Set event trap severity limit to ’major’.
minor
Set event trap severity limit to ’minor’.
warning
Set event trap severity limit to ’warning’.
none
Set event trap severity limit to ’none’.
Set SNMP trap version number, 1 or 2.
Example: set snmp trapvers 1
5-167
CLI Commands
set
set time
Use the set time command to set the time.
Syntax: set time {hh:mm:ss}
Example: set time 12:00:00
The example will set the time to 12 noon.
{hh:mm:ss}
Where hh:mm:ss is the time in hours, minutes, and seconds, using a 24-hour clock.
5-168
Axxius 800 - Release 2.2
CLI Commands
set
set user
Use the set user command to modify attributes for a specific user that have been created with
the add user command.
set user level
Use the set user level command to set the user access level.
Syntax: set user {"user-name"} level {1|2|3}
Example: set user "paul" level 2
{"user-name"}
The user-name is a user ID to add to the system. Text is a single word, with no blank spaces
and must be enclosed in quotes.
{1| 2| 3}
Sets the level of access.
Level 1
Level 2
Level 3
Manager has full access to ALL commands. Typically, there is only one
designated user at this level
Operator has access to all commands except for the add user and set user
commands
Monitor (read only) has access to commands that display reports and status
set user password
Use the set user password to set the password for a defined user.
Syntax: set user {"user-name"} password
Example: set user "john" password [Enter]
New Password: ****
New Password again: ****
{"user-name"}
The user-name is an existing user ID in the system. Text is a single word, with no blank
spaces and must be enclosed in quotes.
Axxius 800 - Release 2.2
5-169
CLI Commands
set
set (v35)
Use the set (v35) command to setup V.35 ports. The command specifies the range of channels
within that card, and the setting to apply.
Syntax: set {v35-addr} {setting}
Example: set 6:1 rxclk normal
To set port 1 (v.35) on slot 6 to no inversion on the receive clock
{v35-addr}
In the form of {slot:port}.
slot
port
Slot number (1-8) of the Axxius chassis where the V.35 card is located
Port number or range.
{setting}
Setting to apply one of the following:
clock
cts
data
equipment
line
rxclkinv
5-170
Set the clock source to one of the following:
external
to the external source
source
to the internal Stratum 4E oscillator
Set the Clear To Send operation mode to one of the following:
cd
follow CD
high
force CTS high
low
force CTS low
rts
follow RTS
Set the data mode to one of the following:
invert
invert the receive and transmit data
normal
do not invert receive and transmit data
Sets the V.35 port to equipment loopback, which loops the transmit V.35
signal back toward the V.35 receive (toward the T1)
loopdown
disable equipment loopback
loopup
enable equipment loopback
Sets the V.35 port to line loopback, which loops the received V.35 signal
back toward the V.35 signal toward the V.35 transmit (away from T1)
loopdown
disable line loopback
loopup
enable line loopback
Set the receive clock invert mode to one of the following:
invert
invert the receive clock
normal
do not invert the receive clock
Axxius 800 - Release 2.2
CLI Commands
set
speed
txclkinv
Axxius 800 - Release 2.2
Set the data rate for each DS0 to which a V.35 is crossconnected
56
56K data rate
64
64K data rate
Set the transmit clock invert mode to one of the following:
invert
invert the transmit clock
normal
do not invert the transmit clock
5-171
CLI Commands
set
set (v54)
Use the set (v54) command to setup V.54 Loopback Test Parameters. The command specifies
the range of channels within that card, and the setting to apply.
Syntax: set {v54-addr} v54 {setting} [off|on] [n] [nnn]
Example: set 6:1 v54 equipment clear
The example will clear the loop test counter on the V.54 card in slot 6, port 1.
{v54-addr}
In the form of {slot:port}.
slot
port
Slot number (1-8) of the Axxius chassis where the V.35/54 card is located
Port number or range.
{setting}
equipment
address
Set the V.54 Equipment (Tx) parameters:
Syntax: set {v54-addr} v54 equipment address {nnn}
Set V.54 loop test address [nnn]
Set the address to be tested.
[nnn] {nnn} must be one of the following:
0 - 255.1, 3, 5, 7, 9, 11, 13, 15,17, 19, 21, 23, 25, 27, 29, 31, 37, 39,
43, 45, 47, 51, 53, 55, 59, 61, 63, 85, 87, 91, 95, 111, 119, 127, 255
(255 disables). See chart below.
clear
Syntax: set{v54-addr} v54 equipment clear
Clear the bit error rate counters during BER test
ignoreack
Syntax: set{v54-addr} v54 equipment ignoreack
{off|on}
Ignore V.54 ACK check [off|on]
Ignore acknowledge from remote equipment. This allows potential
testing with non-compliant equipment by ignoring the acknowledge
phase. WARNING: When choosing this option, the V.35 card
will no longer be compliant with the V.54 specification. Use for
debug purposes only.
loopdown
Syntax: set{v54-addr} v54 equipment loopdown
Stop the test sequence
loopup
Syntax: set{v54-addr} v54 equipment loopup
Start the test sequence
5-172
Axxius 800 - Release 2.2
CLI Commands
set
pattern
Syntax: set{v54-addr} v54 equipment pattern {n}
Set V.54 test pattern n is from the following:
0 = QRSS pattern (default)
1 = 2047 pattern
2 = 215 -1 pattern
3 = 220 -1 pattern (QRSS with no bit stuffing)
prepcnt
network
address
Syntax: set {v54-addr} v54 equipment prepcnt {nnn}
Set V.54 Rx prep-pattern count {nnn}
nnn = the number of times that the preparatory pattern must be
received to be recognized.
Set the V.54 Network loop address.
Syntax: set {v54-addr} v54 network address {nnn}
Set the address of the port to {nnn}.
{nnn} must be one of the following:
1, 3, 5, 7, 9, 11, 13, 15,17, 19, 21, 23, 25, 27, 29, 31, 37, 39, 43, 45,
47, 51, 53, 55, 59, 61, 63, 85, 87, 91, 95, 111, 119, 127, 255 (255
disables). See chart below.
disable
Syntax: set {v54-addr} v54 network disable
Disable V.54 loop test
enable
Syntax: set {v54-addr} v54 network enable
Enable V.54 loop test
prepcnt
Syntax: set {v54-addr} v54 network prepcnt {nnn}
Sets the preparatory pattern response count.
nnn = the number of times that the preparatory pattern must be
received to be recognized.
[nnn] chart
0x01 - 1
0x03 - 3
0x05 - 5
0x07 - 7
0x09 - 9
0x0B - 11
0x0D - 14
0x0F - 15
0x11 - 17
0x13 - 19
0x15 - 21
0x17 - 23
0x19 - 25
0x1B - 27
Axxius 800 - Release 2.2
0x1D - 29
0x1F - 31
0x25 - 37
0x27 - 39
0x2B - 43
0x2D - 45
0x2F - 47
0x33 - 51
0x35 - 53
0x37 - 55
0x3B - 59
0x3D - 61
0x3F - 63
0x55 - 85
0x57 - 87
0x5B - 91
0x5F - 95
0x6F - 111
0x77 - 119
0xFF - 255*
5-173
CLI Commands
set
set verification
Use the set verification command to enable or disable verification prompts.
Syntax: set verification {off|on}
Example: set verification off
The example will cause yes/no verification messages to be suppressed.
{off|on}
off
on
5-174
Turn yes/no verification prompts off.
Turn yes/no verification prompts on.
Axxius 800 - Release 2.2
CLI Commands
show
show
The following show commands are linked to a detailed description of each command.
show (adpcm)
show autoexit
show (bri)
show cclabels
show clock
show connect
show connect adpcm
show date
show (ds0)
show (ds1)
show (ds3)
show ethernet
show external alarms
show (fxo)
show (fxsPS or fxsPSM)
show id
show image
show impedance
show ip
show ipds0
show login
show lsprotect
show ntp
show (ocudp)
show radius
show (router)
show (router) dhcp
show (router) dns
show (router) lmi
show (router) login
Axxius 800 - Release 2.2
show (router) ntp
show (router) port
show (router) ppp
show (router) rip
show (router) snmp
show (router) stp
show (router) syslog
show (router) uploaduser
show (router-lan)
show (router-lan) filter
show (router-lan) static
show (router-lan) stp
show (router-wan)
show (router-wan) firewall
show (router-wan) nat bypass
show (router-wan) ppp
show (router-wan) static ip address
show (router-wan) static ip network
show (router-wan) static ipx network
show (router-wan) static mac address
show (router-wan) static nat address
show (router-wan) stp
show (router-wan) trunk
show screen
show snmp
show syslog
show time
show users
show (v35)
show (v54)
5-175
CLI Commands
show
show (adpcm)
Use the show (adpcm) command to display the settings for the ADPCM card.
Syntax: show {adpcm-addr}
Example: > show 6:1
show 6:1
SLOT 6:
Settings for DS1 1:
Circuit ID:
Up/Down:
Framing:
Line Coding:
Line Build Out:
(CSU 0dB)
Loop Code Detection:
Loopback:
FDL Type:
ADPCM:
ADPCM Map:
CAC DS1# 6:1
UP
ESF
B8ZS
DSX-1 EQUALIZATION FOR 0-133 ft.
ON
OFF
None
Enabled
2
Performance Threshold Settings
unavailable seconds:
severely errored seconds:
errored seconds:
sev. errored frame seconds:
line errored seconds:
controlled slip seconds:
bursty errored seconds:
degraded minutes:
total linecode violations:
total pathcode violations:
15 min.
0
0
0
0
0
0
0
0
0
0
1 day
0
0
0
0
0
0
0
0
0
0
{adpcm-addr}
The ADPCM address is in the form {slot|slot:port}. Where {slot} displays information for
all ports on the card, {slot:port} for only the defined port.
slot
port
5-176
Slot number (1-8) where the ADPCM card is located
Port number, range or all.
Axxius 800 - Release 2.2
CLI Commands
show
show autoexit
Use the show autoexit command to display whether autoexit is on or off. If on, the time-out
period is displayed.
Syntax: show autoexit
Example: > show autoexit
Autoexit is off.
show (bri)
Use the show (bri) command to display settings for BRIs.
Syntax: show {bri-addr}
Example: > show 5:1
The example will display the settings for port 1 (BRI) on slot 5.
SLOT 5:
Settings for BRI Port 1:
Mode:
Up/Down:
CRV:
Performance Sync Source:
Auto Activate:
Performance Threshold Settings
LT3DS0
UP
0
AXXIUS
OFF
errored seconds:
severely errored seconds:
1 hour
-----40
10
25
1 day
-----100
{bri-addr}
The BRI address is in the form {slot|slot:port}. Where {slot} displays information for all
ports on the card, {slot:port} for only the defined port.
slot
port
Axxius 800 - Release 2.2
Slot number (1-8) where the BRI card is located
Port number, range or all.
5-177
CLI Commands
show
show cclabels
The show cclabels command displays all user defined DS0 cross-connect labels.
Syntax: show cclabels
Example: show cclabels
> show cclabels
Current DS0 Connection Labels:
---------------------------’label1’
’label2’
’label3’
’test’
---------’label4’
---------’V35label’
show clock
The show clock command displays the primary and secondary clocks.
Syntax: show clock
Example: show clock
This example will display the primary and secondary clock source.
> show clock
5-178
Primary Master Transmit Clock Source:
Internal
Secondary Transmit Clock Source:
Internal
Axxius 800 - Release 2.2
CLI Commands
show
show connect
The show connect command displays the static connections for channels and ports.
Syntax: show connect {slot|slot:port|slot:port:channel|
slot:port:channel:sub-channel}
Example: show connect a:1:1-4
From
A:01:01
A:01:02
A:01:03
A:01:04
Desc
DATA DS0
DATA DS0
DATA DS0
DATA DS0
Desc
To
Comment
{slot|slot:port|slot:port:channel|slot:port:channel|sub-channel}
slot
port
channel
sub-channel
Axxius 800 - Release 2.2
Slot number A is the Controller card or 1-8 for service cards.
Port number, range or all.
Channel number, range or all.
Sub-channel number, range or all.
5-179
CLI Commands
show
show connect adpcm
The show connect adpcm command displays the connections for the ADPCM port.
Syntax: show connect adpcm {adpcm-addr}
Example: show connect 1:1
> show connect adpcm 1:1
From
Desc
-------------- ------------1:01:01(01/02)
DATA
DS0
1:01:02(03/04)
DATA
DS0
1:01:03(05/06)
DATA
DS0
1:01:04(07/08)
DATA
DS0
1:01:05(09/10)
DATA
DS0
1:01:06(11/12)
DATA
DS0
1:01:07(13/14)
DATA
DS0
1:01:08(15/16)
DATA
DS0
1:01:09(17/18)
DATA
DS0
1:01:10(19/20)
DATA
DS0
1:01:11(21/22)
DATA
DS0
1:01:12(23/24)
DATA
DS0
<-->
<-->
<-->
<-->
<-->
<-->
<-->
<-->
<-->
<-->
<-->
<-->
Desc
------------DS0
DATA
DS0
DATA
DS0
DATA
DS0
DATA
DS0
DATA
DS0
DATA
DS0
DATA
DS0
DATA
DS0
DATA
DS0
DATA
DS0
DATA
DS0
DATA
To
---------1:04:01
1:04:02
1:04:03
1:04:04
1:04:05
1:04:06
1:04:07
1:04:08
1:04:09
1:04:10
1:04:11
1:04:12
{adpcm-addr}
slot
port
The slot number (1-8) that contains the DS1 ADPCM card.
Port number is 1
show date
The show date command displays the date in dd/mm/yyyy format.
Syntax: show date
Example: > show date
date: 08/10/2002
5-180
Axxius 800 - Release 2.2
CLI Commands
show
show (ds0)
The show (ds0) command displays settings for DS0s.
Syntax: show {ds0-addr}
Example: show a:2:1-2
In the following example, the show (ds0) command has queried slot A
(Controller card), port 2, channels 1 through 2.
>show a:2:1-2
SLOT A:
Settings for DS1
Type:
SLOT A:
Settings for DS1
Type:
1:
channel
DATA
1:
1:
channel
DATA
2:
{ds0-addr}
The Controller DS0 addresses are different on the DS3 and DS1 Controller, however the
DS0 address on the service cards does not change with Controller type (DS3 or DS1).
DS0 Address on a DS3 Controller in the form {slot:port:channel:sub-channel}
slot
A for the DS3 Controller card.
port
Port number, range or all.
ds1 channel DS1 channel number, range or all.
ds0 channel DS0 channel number, range or all.
DS0 Address on a DS1 Controller or service cards (with DS1 or DS3 controller) in
the form {slot:port:channel}
slot
A for the DS1 Controller card, or 1-8 for service cards.
port
Port number, range or all.
channel
Channel number, range or all.
Axxius 800 - Release 2.2
5-181
CLI Commands
show
show (ds1)
The show (ds1) command displays settings for DS1s.
Syntax: show {ds1-addr}
Example: show 1:1
SLOT A:
Settings for DS1 1:
Circuit ID:
CAC DS1# A:1
Up/Down:
DOWN
Framing:
ESF
Line Coding:
B8ZS
Line Build Out:
DSX-1 EQUALIZATION FOR 0-133 ft.(CSU 0dB)
Loop Code Detection:ON
Loopback:
OFF
FDL Type:
None
AIS Forwarding:
Enabled
AIS DS1 List:
2:1, 3:1, 4:1, 5:1
Performance Threshold Settings
unavailable seconds:
severely errored seconds:
errored seconds:
sev. errored frame seconds:
line errored seconds:
controlled slip seconds:
bursty errored seconds:
degraded minutes:
total linecode violations:
total pathcode violations:
15 min.
0
0
0
0
0
0
0
0
0
0
1 day
0
0
0
0
0
0
0
0
0
0
{ds1-addr}
The Controller DS1 addresses are different on the DS3 and DS1 Controller, however the
DS1 address on the services cards does not change with Controller type (DS3 or DS1).
DS1 Address on a DS3 Controller in the form {slot:port:channel}
slot
A for the DS3 Controller card.
port
Port number, range or all.
channel
Channel number, range or all.
DS1 Address on a DS1 Controller or service cards (with DS1 or DS3 controller) in
the form {slot:port}
slot
A for the DS1 Controller card, or 1-8 for service cards.
port
Port number, range or all.
5-182
Axxius 800 - Release 2.2
CLI Commands
show
show (ds3)
The show (ds3) command displays the current settings for a DS3.
Syntax: show {ds3-addr}
Example: show a:1
SLOT A:
Settings for DS3 Port 1:
Circuit ID:
Up/Down:
De-jitter Buffer:
Framing:
Transmit Clock:
Loop Code Detection:
Loopback:
Berthreshold:
Protection Switching:
Protection Reversion:
Equipment ID:
Location ID:
Frame ID:
Unit ID:
Facility ID:
Port Number:
Generator Number:
FE Equipment ID:
FE Location ID:
FE Frame ID:
FE Unit ID:
FE Facility ID:
FE Port Number:
FE Generator Number:
CAC T3# A:1
UP
OFF
M23
NORMAL
OFF
OFF
0
OFF
OFF
Performance Threshold Settings
unavailable seconds:
sev. errored frame seconds:
cbit sev. errored seconds:
cbit errored seconds:
pbit sev. errored seconds:
pbit errored seconds:
line errored seconds:
line code violations:
cbit code violations:
pbit code violations:
Axxius 800 - Release 2.2
15 min.
0
0
0
0
0
0
0
0
0
0
1 day
0
0
0
0
0
0
0
0
0
0
5-183
CLI Commands
show
{ds3-addr}
In the form of {slot:port}.
slot
port
A for the controller card (DS3)
Port number or range.
show ethernet
The show ethernet command displays Ethernet and IP settings.
Example: show ethernet
> show ethernet
IP Address and Mask:
IP Address of the Gateway:
MAC Address:
198.162.3.196 255.255.255.0
192.168.3.202
00:E0:97:00:A9:33
show external alarms
The show external alarms command displays the external alarm setting.
Example: show external alarms
> show external alarms
Alarm
1
2
3
4
5
6
7
8
9
10
5-184
Severity
Minor
Minor
Minor
Minor
Minor
Minor
Minor
Minor
Minor
Minor
Description
User
User
User
User
User
User
User
User
User
User
Alarm
Alarm
Alarm
Alarm
Alarm
Alarm
Alarm
Alarm
Alarm
Alarm
Axxius 800 - Release 2.2
CLI Commands
show
show (fxo)
The show (fxo) command displays the settings for FXOs.
Syntax: show {fxo-addr}
Example: show 7:1
The example shows settings for port 1 on the FXO card i slot 7.
> show 7:1
SLOT 7:
Settings for FXO:
Type:
Signaling:
RxGain:
TxGain:
channel 1:
VOICE
LS
-6
dB
-3
dB
{fxo-addr}
In the form of {slot:port}.
slot
port
Axxius 800 - Release 2.2
Location of the FXO card, slot 1-8.
Port number, range or "all".
5-185
CLI Commands
show
show (fxsPS or fxsPSM)
The show (fxsPS or fxsPSM) command displays the settings for the Single Channel POTS
card without modem (FXS PS) or with modem (FXS PSM).
Syntax: show {fxsPS-addr|fxsPSM-addr}
Example: show 8:1
The example shows settings for the FXS PS card in slot 8.
> show 8:1
SLOT 8:
Settings for FXS:
Type:
Signaling:
RxGain:
TxGain:
channel 1:
VOICE
LS
-6
dB
-3
dB
{fxsPS-addr|fxsPSM-addr}
In the form of {slot:port}.
slot
port
Slot number (1-8) that the FXS PS card is located
Port number is 1.
show id
The show id command displays the system ID for the Axxius 800.
Syntax: show id
Example: show id
The example shows the ID of a Axxius 800 labeled "Axxius 8001"
Axxius 8001> show id
ID: Axxius 8001
5-186
Axxius 800 - Release 2.2
CLI Commands
show
show image
The show image command displays the application images stored in the Controller or Router.
Syntax: show [rtr_card-addr] image
Example: show image
> show image
App. Image: Ver=7.0 Fri Aug 29 06:40:42 2003 - ACTIVE
App. Image: Ver=7.0 Thu Aug 14 13:01:18 2003 - BACKUP
Example: show 5 image
> show 5 image
SLOT 5:
App. Image: Ver=1.30K
App. Image: Ver=1.21H
Fri Apr 09 11:53:13 2004 - ACTIVE
Mon Mar 29 09:54:36 2004 - BACKUP
[rtr_card-addr]
The Router card slot number (1-8) to retrieve the image information from. Note: If no slot
number is entered, the image information is retrieved from the Controller.
Axxius 800 - Release 2.2
5-187
CLI Commands
show
show impedance
The show impedance command displays the impedance settings for FXS 5G card.
Syntax: show impedance
Example: show impedance
Index
1
2
3
4
5
6
+
+
+
+
+
+
Impedance
(.110µF ||
(.047µF ||
(.072µF ||
(.100µF ||
(.137µF ||
(.115µF ||
120
150
150
200
215
220
Ohms
Ohms
Ohms
Ohms
Ohms
Ohms
820
510
830
680
1k
820
Ohms)
Ohms)
Ohms)
Ohms)
Ohms)
Ohms)
7
8
9
10
11
12
13
220
270
300
370
400
400
600
Ohms
Ohms
Ohms
Ohms
Ohms
Ohms
Ohms
+
+
+
+
+
+
(.120µF
(.120µF
(.220µF
(.310µF
(.033µF
(.050µF
820
910
1k
620
500
500
Ohms)
Ohms)
Ohms)
Ohms)
Ohms)
Ohms)
14
15
16
17
18
19
600
600
600
800
900
900
Ohms
Ohms
Ohms
Ohms
Ohms
Ohms
+ 1.00µF
+ 1.50µF
+ 2.16µF
+ 2.16µF
||
||
||
||
||
||
CODEC
A-law
A-law
A-law
A-law
A-law
A-law
A-law
A-law
A-law
A-law
A-law
A-law
A-law
µ-law
A-law
µ-law
A-law
A-law
µ-law
Country
Norway
Malaysia
Belgium
China
France
Austria, Germany,
Mexico, Switzerland
Australia
Finland
United Kingdom
New Zealand
Denmark
Greece
Korea, Indonesia,
Italy, Poland,
Russia, Spain,
Thailand, China
Japan
Saudi Arabia
Korea
Netherlands
Brazil
USA, Taiwan
NOTE: Note: In general, µ-Law settings are used for T1 applications,
A-Law settings are used for E1 applications.
5-188
Axxius 800 - Release 2.2
CLI Commands
show
show ip
The show ip command displays the IP Address information for the Axxius 800.
Syntax: show ip
Example: show ip
IP Address and Mask:
IP Address of the Gateway:
192.168.3.193
192.168.3.202
255.255.255.0
OK
show ipds0
The show ipds0 command displays the settings for the DS0 management channel.
Syntax: show ipds0
Example: show ipsd0
Administrative state:
DS0 Selected:
IP Address and Mask:
DOWN
a:1:1
192.168.210.1
255.255.255.0
show login
The show login command displays the RADIUS login authentication configuration settings for
the Controller.
Syntax: show login
Example: show login
Login Authentication Parameters:
Authentication Type: local
Support Logins: enabled
Axxius 800 - Release 2.2
5-189
CLI Commands
show
show lsprotect
The show lsprotect command displays the low speed protection information.
Syntax: show lsprotect
Example: show lsprotect
> SHOW lsprotect
Low Speed Protection Settings:
Low Speed Protection Global Service Enable: ENABLED
Backup Slot Settings:
Backup Slot: 7
Backup Slot Type: Quad T1
Protected Port Settings:
SLOT:
----3
3
3
3
5
6
6
6
6
PORT:
----1
2
3
4
1
1
2
3
4
TYPE:
----QT1:
QT1:
QT1:
QT1:
QT1:
QT1:
QT1:
QT1:
QT1:
T1
T1
T1
T1
T1
T1
T1
T1
T1
REVERSION:
---------NONREVERTIVE
NONREVERTIVE
NONREVERTIVE
NONREVERTIVE
NONREVERTIVE
REVERTIVE
REVERTIVE
REVERTIVE
REVERTIVE
PRIORITY:
--------1
1
1
1
2
7
7
3
7
Number of Protected Ports: 9
5-190
Axxius 800 - Release 2.2
CLI Commands
show
show ntp
The show ntp command displays settings for Network Time Protocol.
Syntax: show ntp
Example: show ntp
NTP Settings:
NTP:
Disabled
NTP Server Address:
0.0.0.0
NTP Polling Interval (seconds):
16
NTP Timezone (offset from GMT): 0 hours 0 minutes
show (ocudp)
Use the show (ocudp) to display baud, loopdetect, error correction, switched and enhanced
switched service and secondary channel provisioning.
Syntax: show {ocudp-addr}
Example: show 2:1
SLOT 2:
Settings for OCUDP Port 1:
Up/Down:
Baudrate:
Loopdetect Types Enabled:
Error Correction:
Secondary Channel:
UP
56000
CSU Non-Latching
DSU Non-Latching
OCU Non-Latching
DISABLE
DISABLE
{ocudp-addr}
The {slot:port} address of the OCU-DP card to display.
slot
port
Axxius 800 - Release 2.2
Slot number (1-8) where the OCU-DP is located. If no port is specified,
all ports will be displayed.
Port number or range.
5-191
CLI Commands
show
show radius
The show radius command displays the RADIUS configuration settings for the Controller.
Syntax: show radius
Example: show radius
RADIUS Configuration Parameters:
Authentication:
NAS Identifier:
Retry count:
Timeout (sec):
Server(1) :
Server(2) :
Server(3) :
5-192
disabled
3
3
UNUSED
UNUSED
UNUSED
Axxius 800 - Release 2.2
CLI Commands
show
show (router)
The show (router) command displays the settings for the Router card.
Syntax: show {rtr_card-addr}
Example: show 1
SLOT 1:
LMI Settings for Router:
LMI:
Disabled
RIP Setting for Router:
RIP Mode Receive:
RIP Mode Send:
RIP1
RIP1
PPP Authentication/Security Settings for Router:
Authentication by Remote:
Protocol:
None
User ID:
Local Profile Name
Authentication of Remote:
Protocol:
None
Local Security Server:
Type:
None
PPP Statistics for Slot-1:
Up/Down
Remote Name State Time
RemoteUnit DOWN 5m19s
x
Packets
0
SNMP Settings for Router:
SNMP Communities:
Address
Name
public
0.0.0.0
Tx
Packets
0
Tx
Octets
0
Access
Read
SNMP Trap Destinations:
Address
Name
public
0.0.0.0
Name:
Contact:
Location:
Rx
Octets
0
Location
Local LAN
unknown
unknown
unknown
DHCP Server/BOOTP Relay Agent Settings for Router:
DHCP:
Disabled
DNS Proxy Settings for Router:
Total: 0
Axxius 800 - Release 2.2
5-193
CLI Commands
show
Spanning Tree Protocol Settings for Router:
Spanning Tree:
Disabled
Syslog Settings for Router:
Syslog:
Disabled
TFTP Upload/Download User Settings for Router:
Reboot After Code is Loaded:
Yes
Reboot After Configuration is Loaded:
Yes
IP Address
Total: 0
Client Site
Upload/Download
Code
Config
LAN Profile Name for Router:
LocalUnit
10.0.0.1
WAN Profile Name(s) for Router:
RemoteUnit
Unnumbered
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
5-194
Axxius 800 - Release 2.2
CLI Commands
show
show (router) dhcp
The show (router) dhcp command displays the current DHCP settings for the Router card.
Syntax: show {rtr_card-addr} dhcp
Example: show 5 dhcp
The following 3 examples, shows there is different information is displayed
depending on the settings.
> show 5 dhcp
SLOT 5:
DHCP Server/BOOTP Relay Agent Settings for Router:
DHCP: Disabled
> show 5 dhcp
SLOT 3:
DHCP Server/BOOTP Relay Agent Settings for Router:
DHCP/BOOTP Relay Agent: Enabled
BOOTP Relay Servers:
192.168.1.1
at RemoteUnit
0.0.0.0
at RemoteUnit
> show 5 dhcp
SLOT 3:
DHCP Server/BOOTP Relay Agent Settings for Router:
DHCP Server:
Enabled
Server Domain:
Starting IP Address:
192.100.1.1
Number:
25
Lease Duration:
0:00
Domain Name Servers:
0.0.0.0
0.0.0.0
0.0.0.0
NetBIOS over TCP/IP Settings:
Node Type:
0
Scope:
NetBIOS Name Servers: 0.0.0.0
0.0.0.0
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
Axxius 800 - Release 2.2
5-195
CLI Commands
show
show (router) dns
The show (router) dns command displays the current DNS setup for the Router card.
Syntax: show {rtr_card-addr} dns
Example: show 3 dns
> show 3 dns
SLOT 3:
DNS Settings:
DNS Resolver:
DNS Server 1 IP Address:
DNS Server 2 IP Address:
DNS Host Name:
DNS Default Domain:
Disabled
0.0.0.0
0.0.0.0
domaintest
DNS Static Host List:
Total: 0
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
show (router) dns proxy
The show (router) dns proxy command displays the current DNS Proxy setup for the Router
card.
Syntax: show {rtr_card-addr} dns proxy
Example: show 3 dns proxy
> show 3 dns proxy
SLOT 3:
DNS Proxy Settings for Router:
Total: 0
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
5-196
Axxius 800 - Release 2.2
CLI Commands
show
show (router) lmi
The show (router) lmi command displays the current Local Management Interface (LMI)
settings for the Router card.
Syntax: show {rtr_card-addr} lmi
Example: show 5 lmi
The example shows the LMI settings for the Router card in slot 5.
> show 5 lmi
SLOT 5:
LMI Settings for Router:
LMI: Disabled
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
show (router) login
The show (router) login command displays the Router login configuration.
Syntax: show {rtr_card-addr} login
Example: show 1 login
SLOT 1:
Login Settings for Router:
Authentication: Local
Login Prompt:
Enabled
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
Axxius 800 - Release 2.2
5-197
CLI Commands
show
show (router) ntp
The show (router) ntp command displays settings for NTP options.
Syntax: show {rtr_card-addr} ntp
Example: show 4 ntp
The example shows the NTP options for the Router card in slot 4.
> show 4 ntp
SLOT 4:
NTP Settings for QTSR:
NTP:
Disabled
NTP Server:
0.0.0.0
NTP Interval (seconds):120
NTP Timezone (offset from GMT):0 hours 0 minutes
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
5-198
Axxius 800 - Release 2.2
CLI Commands
show
show (router) port
The show (router) port command displays the current TSR ports configuration. This command
applies to the Terminal Server Router card only.
Syntax: show {tsr_card-addr} port
Example: show 1 port
SLOT 1:
Port Profiles for Terminal Server Router:
Port 1
Name: none
Type: RS-232
Asynchronous Settings
Socket: 10.10.11.1:23 TCP
Baud Rate
9600
Data Bits
8
Stop Bits
1
No Parity
No Flowcontrol
Port 2
Name: none
Type: RS-232
Asynchronous Settings
Socket: 10.10.11.2:23 TCP
Baud Rate
9600
Data Bits
8
Stop Bits
1
No Parity
No Flowcontrol
Port 3
Name: none
Type: Ethernet
Port 4
Name: none
Type: Ethernet
{tsr_card-addr}
The slot number (1-8) that contains the TSR card.
Axxius 800 - Release 2.2
5-199
CLI Commands
show
show (router) ppp
The show (router) ppp command displays the current Local PPP (Point-to-Point Protocol)
authentication and security settings for the Router card.
Syntax: show {rtr_card-addr} ppp
Example: show 5 ppp
> show 5 ppp
SLOT 5:
PPP Authentication/Security Settings for Router:
Authentication by Remote:
Protocol:
CHAP
Secret:
public
User ID:
Local Profile Name
Authentication of Remote:
Protocol:
CHAP
Local Security Server:
Type:
Radius
IP Address:
168.0.0.100
Password:
test
PPP Statistics for Slot-4:
Up/Down
Rx
Rx
Tx
Tx
Remote Name State Time
Packets
Octets
Packets
Octets
----------- ----- --------- ---------- --------- --------- ----RemoteAxxius
DOWN 26m36s
0
0
0
0
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
5-200
Axxius 800 - Release 2.2
CLI Commands
show
show (router) rip
The show (router) rip command displays the current RIP settings for the Router card.
Syntax: show {rtr_card-addr} rip
Example: show 5 rip
SLOT 5:
RIP Settings for Router:
RIP Mode Receive:
RIP2
RIP Mode Send:
Rip2
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
show (router) snmp
The show (router) snmp command displays the current SNMP settings for the specified Router
card.
Syntax: show {rtr_card-addr} snmp
Example: show 5 snmp
SLOT 5:
SNMP Settings for Router:
SNMP Communities:
Address
Name
public
0.0.0.0
Access
Read
SNMP Trap Destinations:
Address
Name
public
0.0.0.0
Location
Local LAN
Statistics Averaging Interval:
1 min.
Name:
Contact:
Location:
unknown
unknown
unknown
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
Axxius 800 - Release 2.2
5-201
CLI Commands
show
show (router) stp
The show (router) stp command displays the current Spanning Tree Protocol settings for the
specified Router card.
Syntax: show {rtr_card-addr} stp
Example: show 5 stp
> show 5 stp
SLOT 5:
Spanning Tree Protocol Settings for Router:
Spanning Tree:
Enabled
Bridge Hello Time:
2 seconds
Bridge Max Age:
20 seconds
Bridge Forward Delay: 15 seconds
Bridge Priority:
32768
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
show (router) syslog
The show (router) syslog command displays the current Syslog setup for the Router card.
Syntax: show {rtr_card-addr} syslog
Example: show 5 syslog
> show 5 syslog
SLOT 5:
Syslog Settings for Router:
Syslog:
Enabled
Facility:
20
Level:
3
Server IP Address:
192.168.3.3
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
5-202
Axxius 800 - Release 2.2
CLI Commands
show
show (router) uploaduser
The show uploaduser command displays the current list of users allowed to upload and
download configuration and code files.
Syntax: show {rtr_card-addr} uploaduser
Example: show 5 uploaduser
> show 5 uploaduser
SLOT 5:
TFTP Upload/Download User Settings for Router:
Reboot After Code is Loaded:
Yes
Reboot After Configuration is Loaded:
Yes
IP Address
--------------Any
Total: 1
Client Site
----------Axxius1
Upload/Download
Code
Config
--------X
X
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
Axxius 800 - Release 2.2
5-203
CLI Commands
show
show (router-lan)
The show (router-lan) command displays the settings for the router card.
Syntax: show {rtr_lan-addr}
Example: show 3:1
> show 3:1
SLOT 3:
Settings for TSR LAN 1:
Profile Name:
Up/Down:
Proxy:
Physical link:
MAC Address:
IP Settings:
IP Address and Mask:
Default Router:
Enabled Frame Types:
RIP Direction:
LocalUnit
UP
Disabled
Automatic
00:E0:97:FF:FF:FE
10.0.0.1
0.0.0.0
Ethernet II
Neither
255.0.0.0
IPX Settings:
Enabled Frame Types: Ethernet II,IEEE 802.2,IEEE 802.3,SNAP
RIP Direction:
Neither
802.2 Ext. Network:
00000000
Eth II Ext. Network:
00000000
SNAP
Ext. Network:
00000000
802.3 Ext. Network:
00000000
Other Settings:
Enabled Frame Types:
Ethernet II, IEEE 802.2, SNAP
LAN Spanning Tree Pro7tocol Settings for LocalUnit:
Spanning Tree:
Disabled
Static IP Network Settings for LocalUnit:
Total: 0
Static IPX Network Settings for LocalUnit:
Total: 0
Static IP Address Settings for LocalUnit:
5-204
Axxius 800 - Release 2.2
CLI Commands
show
Total: 0
Static MAC Address Settings for LocalUnit:
Total: 0
LAN Filters Enabled for LocalUnit:
Forward Mode: Forward ALL Frames NOT Matching Filters
Filter Type
Total: 0
Source/Dest
Filter Name
LAN MAC Address Filters Defined for LocalUnit:
Total: 0
LAN Protocol Filters Defined for LocalUnit:
Total: 0
LAN Custom Filters Enabled Defined for LocalUnit:
Total: 0
Settings for TSR WAN RemoteUnit:
State:
Enabled
IP Settings:
Mode:
Route
WAN Network Updates: Never
GRE Tunneling:
Disabled
IPX Settings:
Mode:
Blocked
Other Settings:
Mode:
Blocked
NAT Gateway:
WAN Numbered IP:
Disabled
No
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
Axxius 800 - Release 2.2
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed in
quotes, with a maximum length of 11 characters.
5-205
CLI Commands
show
show (router-lan) filter
The show (router-lan) filter command displays the current LAN Layer 2 data filters applied to
the LAN on the specified Router card.
Syntax: show {rtr_lan-addr} filter
[address|all|custom|protocol]
Example: show 5:1 filter
> show 5:1 filter
SLOT 5:
LAN Filters Enabled for Axxius50:
Forward Mode: Forward ALL Frames NOT Matching Filters
Filter Type
----------Protocol
Protocol
Total: 2
Source/Dest
-----------
Filter Name
----------XNSrule
XNSrule
Example: show 5:1 filter all
> show 5:1 filter all
SLOT 5:
LAN MAC Address Filters Defined for Axxius50:
Total: 0
LAN Protocol Filters Defined for Axxius50:
Protocol Name
------------SPANTRE
XNSrule
XNSrule
Total: 3
Ethernet Value
-------------0
807
807
IEEE Value
---------42
0
0
LAN Custom Filters Enabled Defined for Axxius50:
Total: 0
5-206
Axxius 800 - Release 2.2
CLI Commands
show
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}
slot
port
"profile-name"
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
[address|custom|protocol|all]
This setting will display the defined filter types of the specified filters.
address
custom
protocol
all
Axxius 800 - Release 2.2
Display Address filters only.
Display Custom filters only.
Display Protocol filters only.
Display all the defined filters.
5-207
CLI Commands
show
show (router-lan) static
The show (router-lan) static commands to display the current list of static entries for the LAN
on the specified Router card.
show (router-lan) static ip address
The show (router-lan) static ip address command displays the current list of static IP
address entries for the LAN on the specified TSR card.
Syntax: show {rtr_lan-addr} static ip address
Example: show 5:1 static ip address
> show 5:1 static ip address
SLOT 5:
Static IP Address Settings for Axxius50:
Device Name
----------Axxius122
Total: 1
IP Address
--------------120.0.0.10
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
5-208
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed in
quotes, with a maximum length of 11 characters.
Axxius 800 - Release 2.2
CLI Commands
show
show (router-lan) static ip network
The show (router-lan) static ip network command displays the current list of static IP
network entries for the LAN on the specified Router card.
Syntax: show {rtr_lan-addr} static ip network
Example: show 5:1 static ip network
SLOT 5:
Static IP Network Settings for Adit50:
Network
100.0.0.0
Total: 1
Subnet Mask
255.0.0.0
Metric
1
Next Gateway
192.136.43.52
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.
show (router-lan) static ipx network
The show (router-lan) static ipx network command displays the current list of static IPX
network entries for the LAN on the specified Router card.
Syntax: show {rtr_lan-addr} static ipx network
Example: show 5:1 static ipx network
> show 5:1 static ipx network
SLOT 5:
Static IPX Network Settings for Axxius50:
Total: 0
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
Axxius 800 - Release 2.2
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the TSR interface. Name must be enclosed in
quotes, with a maximum length of 11 characters.
5-209
CLI Commands
show
show (router-lan) static mac address
The show (router-lan) static mac address command displays the current list of static
MAC address entries for the LAN on the specified Router card.
Syntax: show {rtr_lan-addr} static mac address
Example: show 5:1 static mac address
SLOT 5:
Static MAC Address Settings for Adit50:
Device Name
Axxius 66
Total: 1
MAC Address
00:E0:97:00:E9:CD
{tsr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
5-210
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed in
quotes, with a maximum length of 11 characters.
Axxius 800 - Release 2.2
CLI Commands
show
show (router-lan) stp
The show (router-lan) stp command displays the current Spanning Tree Protocol settings for
the specified LAN interface.
Syntax: show {rtr_lan-addr} stp
Example: show 3:1 stp
> show 3:1 stp
SLOT 3:
LAN Spanning Tree Protocol Settings for LocalUnit:
Spanning Tree:
Enabled
Port Cost:
100
seconds
Port Priority:
128
seconds
{rtr_lan-addr}
The Router address is in the form {slot:port} or {slot "profile-name"}.
slot
port
"profile-name"
Axxius 800 - Release 2.2
The slot number (1-8) that contains the Router card.
Port number of the Router.
The profile name for the Router interface. Name must be enclosed in
quotes, with a maximum length of 11 characters.
5-211
CLI Commands
show
show (router-wan)
The show (router-wan) command displays the current configuration settings for the specified
WAN interface.
Syntax: show {rtr_card-addr} {"wan-name"}
Example: show 3 "RemoteUnit"
> show 3 "RemoteUnit"
SLOT 3:
Settings for TSR WAN LosAngeles:
State:
Enabled
IP Settings:
Mode:
Route
WAN Network Updates: Never
GRE Tunneling:
Disabled
IPX Settings:
Mode:
Blocked
Other Settings:
Mode:
Blocked
NAT Gateway:
WAN Numbered IP:
Disabled
No
WAN PPP Authentication/Security Settings for RemoteUnit:
Authentication of Remote User:
User ID:
Remote Profile Name: RemoteUnit
Security Server:
Local
Compression:
Typical Data:
Disabled
Easy to Compress
PPP Statistics for Slot-3:
Up/Down
Remote Name State Time
RemoteUnit
DOWN 38m30s
Rx
Packets
0
Rx
Octets
0
Tx
Packets
0
Tx
Octets
0
WAN Trunk Setting for RemoteUnit:
No Trunk Assigned
5-212
Axxius 800 - Release 2.2
CLI Commands
show
WAN Spanning Tree Protocol Settings for RemoteUnit:
Spanning Tree:
Disabled
WAN Static IP Network Settings for RemoteUnit:
Total: 0
WAN Static IPX Network Settings for RemoteUnit:
Total: 0
WAN Static IP Address Settings for RemoteUnit:
Total: 0
WAN Static MAC Address Settings for RemoteUnit:
Total: 0
WAN Static NAT Address Settings for RemoteUnit:
Total: 0
WAN Firewall Settings for RemoteUnit:
Service(s)
1.
Telnet
Last ! Any
LAN Device(s)
WAN Device(s)
100.2.3.4/32
<==
*
*
<== ==> *
Lo
Log
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
An existing WAN interface to modify. The name must be enclosed in quotes.
Axxius 800 - Release 2.2
5-213
CLI Commands
show
show (router-wan) firewall
The show (router-wan) firewall command displays the current firewall filter settings for the
specified WAN interface.
Syntax: show {rtr_card-addr} {"wan-name"} firewall
Example: show 5 "LosAngeles" firewall
> show 5 "LosAngeles" firewall
SLOT 5:
WAN Firewall Settings for LosAngeles:
Service(s)
1. SMTP
2. Telnet
Last ! Any
LAN Device(s)
192.0.0.0/8
100.0.0.0/24
*
WAN Device(s)
==> 192.0.0.0/8
==> 200.0.0.0/24
<== ==> *
Log
Log
Alm
{rtr_card-addr} - The slot number (1-8) that contains the Router card.
{"wan-name"} - The WAN interface to modify. The name must be enclosed in quotes.
show (router-wan) nat bypass
Use the show (router-wan) nat bypass command to see the current list of NAT bypass entries
for the WAN interface on the specified Router card.
Syntax: show {rtr_card-addr} {"wan-name"} nat bypass
Example: show 2 "RemoteUnit" nat bypass
SLOT 2:
WAN NAT Bypass Address Settings for RemoteAdit:
IP Address
156.65.0.0
201.23.16.0
Total: 2
Netmask
255.255.255.0
255.255.255.0
{rtr_card-addr} - The slot number (1-8) that contains the Router card.
{"wan-name"} - The WAN interface to modify. The name must be enclosed in quotes.
5-214
Axxius 800 - Release 2.2
CLI Commands
show
show (router-wan) ppp
The show (router-wan) ppp command displays the current PPP (Point-to-Point Protocol)
settings for the specified WAN interface.
Syntax: show {rtr_card-addr} {"wan-name"} ppp
Example: show 5 "LosAngeles" ppp
> show 5 "LosAngeles" ppp
SLOT 5:
WAN PPP Authentication/Security Settings for LosAngeles:
Authentication of Remote User:
User ID:
Remote Profile Name: LosAngeles
Security Server:
Local
Compression:
Typical Data:
PPP Statistics for Slot-4:
Disabled
Easy to Compress
Up/Down
Rx
Rx
Tx
Tx
Remote Name State Time
Packets
Octets
Packets
Octets
------------ ----- --------- ---------- --------- ---------- --RemoteAxxius
DOWN 26m36s
0
0
0
0
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
Axxius 800 - Release 2.2
5-215
CLI Commands
show
show (router-wan) static ip address
The show (router-wan) static ip address command displays the current list of static IP address
entries for the specified WAN interface.
Syntax: show {rtr_card-addr} {"wan-name"} static ip address
Example: show 5 "LosAngeles" static ip address
> show 5 "LosAngeles" static ip address
SLOT 5:
WAN Static IP Address Settings for LosAngeles:
Total: 0
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
show (router-wan) static ip network
The show (router-wan) static ip network command displays the current list of static IP
network entries for the specified WAN interface.
Syntax: show {rtr_card-addr} {"wan-name"} static ip network
Example: show 5 "LosAngeles" static ip network
> show 5 "LosAngeles" static ip network
SLOT 5:
WAN Static IP Network Settings for LosAngeles:
Network
200.1.1.0
Total: 1
Subnet Mask
255.255.255.0
Metric
1
Remote Tunnel Addr
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
5-216
Axxius 800 - Release 2.2
CLI Commands
show
show (router-wan) static ipx network
The show (router-wan) static ipx network command displays the current list of static IPX
network entries for the specified WAN interface.
Syntax: show {rtr_card-addr} {"wan-name"} static ipx network
Example: show 5 "LosAngeles" static ipx network
SLOT 5:
WAN Static IPX Network Settings for LosAngeles:
Network
00000011
Total: 1
Hops
2
Ticks
4
Next IPX Router
00:00:00:00:00:00
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
show (router-wan) static mac address
The show (router-wan) static mac address command displays the current list of static IP MAC
address entries for the specified WAN interface.
Syntax: show {rtr_card-addr} {"wan-name"} static mac address
Example: show 5 "LosAngeles" static mac address
SLOT 5:
WAN Static MAC Address Settings for LosAngeles:
Device Name
Axxius32
Total: 1
MAC Address
00:E0:97:00:E9:CD
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
Axxius 800 - Release 2.2
5-217
CLI Commands
show
show (router-wan) static nat address
The show (router-wan) static nat address command displays the current static NAT address
entries for the specified WAN interface.
Syntax: show {rtr_card-addr} {"wan-name"} static nat address
Example: show 5 "LosAngeles" static nat address
> show 5 "RemoteUnit" static nat address
SLOT 5:
WAN Static NAT Address Settings for RemoteUnit:
Total: 0
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
show (router-wan) stp
The show (router-wan) stp command displays the current Spanning Tree Protocol settings for
the specified WAN interface.
Syntax: show {rtr_card-addr} {"wan-name"} stp
Example: show 5 "LosAngeles" stp
> show 5 "LosAngeles" stp
SLOT 5:
WAN Spanning Tree Protocol Settings for LosAngeles:
Spanning Tree:
Enabled
Port Cost:
651
seconds
Port Priority:
128 seconds
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
5-218
Axxius 800 - Release 2.2
CLI Commands
show
show (router-wan) trunk
The show (router-wan) trunk command displays the current trunk assignment for the specified
WAN interface.
Syntax: show {rtr_card-addr} {"wan-name"} trunk
Example: show 5 "LosAngeles" trunk
> show 5 "LosAngeles" trunk
SLOT 5:
WAN Trunk Setting for LosAngeles:
WAN Port Number:
1
Connection Type:
PPP
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
{"wan-name"}
The WAN interface to modify. The name must be enclosed in quotes.
show screen
The show screen command displays the screen settings.
Example: show screen
Screen Height = 23
Axxius 800 - Release 2.2
5-219
CLI Commands
show
show snmp
The show snmp command displays the SNMP settings.
Example: show snmp
SNMP Settings:
System Name:
System Location:
System Contact:
GET Community:
SET Community:
TRAP Community:
Trap version:
Authentication TRAP
Event TRAP
NMS 1:
NMS 2:
NMS 3:
public
desktop
public
0
disabled
none
show syslog
The show syslog command displays settings for the system log.
Syntax: show syslog
Example: show syslog
Syslog Settings:
5-220
Syslog:
Disabled
Server
IP Address
Facility
Threshold Level
1
2
3
0.0.0.0
0.0.0.0
0.0.0.0
16
16
16
3
3
3
Axxius 800 - Release 2.2
CLI Commands
show
show time
The show time command displays the system time, in 24 hour hh:mm:ss format.
Syntax: show time
Example: show time
> show time
time:
00:22:51
show users
The show users command displays a list of all users and their settings, and if they are logged
on at the time (0=not logged on, 1=logged on).
Syntax: show users
Example: > show users
User
---* jack
Level
----1
Last Login
---------00:00:13 01/01/1999
Logged In
--------1
* indicates self
Axxius 800 - Release 2.2
5-221
CLI Commands
show
show (v35)
Use the show (v35) to display current settings for V.35 card.
Syntax: show {v35-addr}
Example: show 2:1
The example shows settings for port 1 (V.35) on slot 2.
> show 2:1
SLOT 2:
Settings for V35 Port 1:
CTS:
Timing:
Rx Clock Inversion:
Tx Clock Inversion:
Data Inversion:
Data Speed:
Data Rate:
Loopback:
Always High
Source
Normal
Normal
Normal
64K
None
{v35-addr}
In the form {slot|slot:port}.
slot
port
5-222
slot (1-8) location of a V.35 card.
Port number or range.
Axxius 800 - Release 2.2
CLI Commands
show
show (v54)
Use the show (v54) to display current settings for V.54 card.
Syntax: show {v54-addr}
Example: show 3:1
The example shows settings for port 1 (V.54) on slot 3.
> show 3
SLOT 3:
Settings for V35 Port 1:
CTS:
Timing:
Rx Clock Inversion:
Tx Clock Inversion:
Data Inversion:
Data Speed:
Data Rate:
V.54 Rx LB:
V.54 Rx Addr:
V.54 Test Addr:
V.54 Tx Prep count:
V.54 Rx Prep count:
V.54 Test Pattern:
V.54 Ignore ACK:
Loopback:
Always High
Source
Normal
Normal
Normal
64K
disabled
0
0
15
15
QRSS
OFF
None
{v54-addr}
In the form {slot|slot:port}.
slot
port
Axxius 800 - Release 2.2
slot (1-8) location of a V.35/54 card.
Port number or range.
5-223
CLI Commands
status
status
Use the status command to see the status of the system clocks, DS0s, DS1s, equipment, and the
DS0 Management Channel.
status (adpcm)
status equipment
status (adpcm) performance
status (fxo)
status (adpcm) performance history
status (fxsPS or fxsPSM)
status (bri)
status ipds0
status (bri) performance
status lsprotect
status (bri) performance history
status (ocudp)
status clock
status (ocudp) performance
status (ds0)
status (ocudp) performance history
status (ds1)
status (router)
status (ds1) performance
status (router-lan)
status (ds3) performance history
status (router-trunk)
status (ds3)
status sessions
status (ds3) performance
status (v54)
status (ds3) performance history
5-224
Axxius 800 - Release 2.2
CLI Commands
status
status (adpcm)
Use the status (adpcm) command to display the status information for the ADPCM card.
Syntax: status {adpcm-addr}
Example: status 6:1
> status 6:1
SLOT 6:
Status for DS1
Receive:
Transmit:
Loopback:
1:
Loss of Signal
RAI/Yellow Alarm
OFF
{adpcm-addr}
The ADPCM address is in the form {slot|slot:port}. Where {slot} displays information for
all ports on the card, {slot:port} for only the defined port.
slot
port
Axxius 800 - Release 2.2
Slot number (1-8) where the ADPCM card is located
Port number. range 1-4. If no port is entered all ports will be displayed.
5-225
CLI Commands
status
status (adpcm) performance
Use the status (adpcm) performance command to display the performance statistics for the
current (15 min) and previous (15 min, hour and day) information for the ADPCM card.
Syntax: status {adpcm-addr} performance
Example: status 6:1 performance
> status 6:1 performance
SLOT 6:
Performance Statistics for DS1
1:
current
15 min.
15 min.
unavailable seconds:
69
900
severely errored seconds:
0
0
errored seconds:
0
0
sev. errored frame seconds:
0
0
line errored seconds:
0
0
controlled slip seconds:
0
0
bursty errored seconds:
0
0
degraded minutes:
total linecode violations:
total pathcode violations:
elapsed time in current
valid 15 min. intervals
valid 15 min. intervals
* - indicates threshold
0
0
0
15 min. interval:
in hour:
in Day:
has been crossed.
0
0
0
1 hour
3600
0
0
0
0
0
0
previous
1 day
7200
0
0
0
0
0
0
0
0
0
0
0
0
1:09
4
8
{adpcm-addr}
The ADPCM address is in the form {slot:port}.
slot
port
5-226
Slot number (1-8) where the ADPCM card is located
Port number, range or all.
Axxius 800 - Release 2.2
CLI Commands
status
status (adpcm) performance history
Use the status (adpcm) performance history command to display performance statistics for
the current 15 minute interval and all previous 15 minute intervals (up to a total of 96) for the
ADPCM card.
Syntax: status {adpcm-addr} performance history
Example: status 6:1 performance history
> status 6:1 performance history
SLOT 6:
Performance Statistics for DS1 1:
UAS SES ES SEFS LES CSS BES
curr. interval: 317
0
0
0
0
0
0
prev. intvl 1: 900
0
0
0
0
0
0
prev. intvl 2: 900
0
0
0
0
0
0
prev. intvl 3: 900
0
0
0
0
0
0
prev. intvl 4: 900
0
0
0
0
0
0
.
.
.
prev. intvl 93: 900
0
0
0
0
0
0
prev. intvl 94: 900
0
0
0
0
0
0
prev. intvl 95: 900
0
0
0
0
0
0
prev. intvl 96: 900
0
0
0
0
0
0
totals:
21181
0
0
0
0
0
0
elapsed time in current 15 min. interval:
valid 15 min. intervals in data:
DM
0
0
0
0
0
LCV
0
0
0
0
0
PCV
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
5:17
96
{adpcm-addr}
The ADPCM address is in the form {slot:port}.
slot
port
Axxius 800 - Release 2.2
Slot number (1-8) where the ADPCM card is located
Port number, range or all.
5-227
CLI Commands
status
status (bri)
Use the status (bri) command to display the status information for the ISDN BRI card.
Syntax: status {bri-addr}
Example: status 3:1
The example displays status of port 1 (BRI) on slot 3.
> status 3:1
SLOT 3:
Status for BRI Port 1:
Loopback:
Corrupt CRC:
NONE
NONE
{bri-addr}
The BRI address, in the form {slot:port}.
slot
port
5-228
The slot number (1-8) that contains the BRI card
Port number, range or all
Axxius 800 - Release 2.2
CLI Commands
status
status (bri) performance
Use the status (bri) performance command to display the performance statistics for the current
(hour and day) and previous (hour and day) for the ISDN BRI card.
Syntax: status {bri-addr} performance
Example: status 3:1 performance
> status 3:1 performance
SLOT 3:
Performance Statistics for BRI Port 1:
current
1 hour
errored seconds:
0
severely errored seconds:
0
block errors:
0
previous
1 hour
0
0
0
current
day
0
0
previous
day
0
0
elapsed time in current 1-hour interval: 00:38:00
completed 1-hour intervals in data:
0
{bri-addr}
The BRI address, in the form {slot:port}.
slot
port
Axxius 800 - Release 2.2
The slot number (1-8) that contains the BRI card
Port number, range or all
5-229
CLI Commands
status
status (bri) performance history
Use the status (bri) performance history command to display the performance statistics for
the current 1 hour interval and all previous 1 hour intervals for the ISDN BRI card.
Syntax: status {bri-addr} performance history
Example: status 5:1 performance history
SLOT 5:
Performance Statistics for BRI Port 1:
HSES
HES
current interval
0
0
prev. interval 1
0
0
prev. interval 2
0
totals:
0
0
BE
0
0
DES
0
0
DSES
0
0
0
0
0
elapsed time in current 1-hour interval: 00:37:38
completed 1-hour intervals in data:
2
{bri-addr}
The BRI address, in the form {slot:port}.
slot
port
The slot number (1-8) that contains the BRI card
Port number, range or all
status clock
Use the status clock command to display the current status of the primary and secondary clocks.
Syntax: status clock
Example: status clock
Active Clock Source: Secondary
Primary:
Clock Source:
Clock Status:
Secondary:
Clock Source:
Clock Status:
5-230
Slot A DS1 1
Out of Service
Internal
In Service
Axxius 800 - Release 2.2
CLI Commands
status
status (ds0)
Use the status (ds0) command to display the current status of the specified DS0.
Syntax: status {ds0-addr}
Example: status a:1:1
Displays the current status of the DS0s on port 1 on slot A
(controller card), port 1, channel 1.
> status a:1:1
DS0
A:1:1
Rx AB
11
Tx AB
01
Signal
EMW
T1
Traffic
TP
N
Display Descriptions
Rx AB - AB bits received by the FXS or FXO port
Tx AB -
AB bits transmitted by the FXS or FXO port
Signal -
Signaling mode for which the port is configured
T1 TP -
T1 Status
Trunk Processing
{ds0-addr}
The Controller DS0 addresses are different on the DS3 and DS1 Controller, however the
DS0 address on the service cards does not change with Controller type (DS3 or DS1).
DS0 Address on a DS3 Controller in the form {slot:port:channel:sub-channel}
slot
A for the DS3 Controller card.
port
Port number, range or all.
ds1 channel DS1 channel number, range or all.
ds0 channel DS0 channel number, range or all.
DS0 Address on a DS1 Controller or service cards (with DS1 or DS3 controller) in
the form {slot:port:channel}
slot
A for the DS1 Controller card, or 1-8 for service cards.
port
Port number, range or all.
channel
Channel number, range or all.
Axxius 800 - Release 2.2
5-231
CLI Commands
status
status (ds1)
Use the status (ds1) command to display the current status of a DS1.
Syntax: status {ds1-addr} [performance] [history]
Example: status a:1
SLOT A:
Status for DS1
Receive:
Transmit:
Loopback:
1:
Traffic
Traffic
OFF
Example: status 1:1
SLOT A:
Status for DS1
Receive:
Transmit:
Loopback:
1:
Loss of Signal
AIS
OFF
{ds1-addr}
The Controller DS1 addresses are different on the DS3 and DS1 Controller, however the
DS1 address on the services cards does not change with Controller type (DS3 or DS1).
DS1 Address on a DS3 Controller in the form {slot:port:channel}
slot
A for the DS3 Controller card.
port
Port number, range or all.
channel
Channel number, range or all.
DS1 Address on a DS1 Controller or service cards (with DS1 or DS3 controller) in
the form {slot:port}
slot
A for the DS1 Controller card (DS1 mode), or 1-8 for service cards.
port
Port number, range or all.
5-232
Axxius 800 - Release 2.2
CLI Commands
status
status (ds1) performance
Use the status (ds1) performance command to display the performance statistics for the
current (15 min) and previous (15 min, hour and day) information of a DS1.
Syntax: status {ds1-addr} performance
Example: status a:1 performance
SLOT A:
Performance Statistics for DS1
1:
current
15 min.
15 min.
unavailable seconds:
89
900
severely errored seconds:
0
0
errored seconds:
0
0
sev. errored frame seconds:
0
0
line errored seconds:
0
0
controlled slip seconds:
0
0
bursty errored seconds:
0
0
degraded minutes:
total linecode violations:
total pathcode violations:
elapsed time in current
valid 15 min. intervals
valid 15 min. intervals
* - indicates threshold
0
0
0
15 min. interval:
in hour:
in Day:
has been crossed.
0
0
0
previous
1 hour
1 day
2700
2700
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1:29
3
3
{ds1-addr}
The Controller DS1 addresses are different on the DS3 and DS1 Controller, however the
DS1 address on the services cards does not change with Controller type (DS3 or DS1).
DS1 Address on a DS3 Controller in the form {slot:port:channel}
slot
A for the DS3 Controller card.
port
Port number, range or all.
channel
Channel number, range or all.
DS1 Address on a DS1 Controller or service cards (with DS1 or DS3 controller) in
the form {slot:port}
slot
A for the DS1 Controller card (DS1 mode), or 1-8 for service cards.
port
Port number, range or all.
Axxius 800 - Release 2.2
5-233
CLI Commands
status
status (ds1) performance history
Use the status (ds1) performance history command to display performance statistics for the
current 15 minute interval and all previous 15 minute intervals (up to a total of 96) of a DS1.
Syntax: status {ds1-addr} performance history
Example: status a:1 performance history
SLOT A:
Performance Statistics for DS1
curr.
prev.
prev.
prev.
prev.
UAS SES
interval: 288
intvl 1: 900
intvl 2: 900
intvl 3: 900
intvl 4: 900
totals:
3888
ES
0
0
0
0
0
0
1:
SEFS
0
0
0
0
0
LES CSS BES DM
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
elapsed time in current 15 min. interval:
valid 15 min. intervals in data:
0
0
LCV
0
0
0
0
0
PCV
0
0
0
0
0
0
0
4:48
4
{ds1-addr}
The Controller DS1 addresses are different on the DS3 and DS1 Controller, however the
DS1 address on the services cards does not change with Controller type (DS3 or DS1).
DS1 Address on a DS3 Controller in the form {slot:port:channel}
slot
A for the DS3 Controller card.
port
Port number, range or all.
channel
Channel number, range or all.
DS1 Address on a DS1 Controller or service cards (with DS1 or DS3 controller) in
the form {slot:port}
slot
A for the DS1 Controller card (DS1 mode), or 1-8 for service cards.
port
Port number, range or all.
5-234
Axxius 800 - Release 2.2
CLI Commands
status
status (ds3)
Use the status (ds3) command to display the current status of the specified DS3.
Syntax: status {ds3-addr}
Example: status a:1
> status a:1
SLOT A:
Status for DS3
Status for DS3
Receive:
Transmit:
Loopback:
1
DS1
1:
1:
Loss of Framing
Traffic
OFF
{ds3-addr}
In the form of {slot port}:
slot
port
Axxius 800 - Release 2.2
A, with a DS3 controller card installed.
Port number or range. Range of ports is 1-2
5-235
CLI Commands
status
status (ds3) performance
Use the status (ds3) performance command to display the performance statistics for the
current (15 min) and previous (15 min, hour and day) information of a DS3.
Syntax: status {ds3-addr} performance
> status a:1 performance
SLOT A:
Performance Statistics for DS3 Port 1:
Near End Statistics:
current previous
15 min.
15 min.
unavailable seconds:
0
0
sev. errored frame seconds:
0
0
sev. errored c-bit seconds:
0
0
errored c-bit seconds:
0
0
sev. errored p-bit seconds:
0
0
p-bit errored seconds:
0
0
line errored seconds:
0
0
total linecode violations:
total pathcode violations:
total cbitcode violations:
Far End Statistics:
unavailable seconds:
sev. errored c-bit seconds:
errored c-bit seconds:
total cbitcode violations:
elapsed time in current
valid 15 min. intervals
valid 15 min. intervals
* - indicates threshold
0
0
0
0
0
0
0
0
0
0
15 min. interval:
in hour:
in Day:
has been crossed.
0
0
0
0
1 hour
0
0
0
0
0
0
0
1 day
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
4:24
3
3
{ds3-addr}
In the form of {slot port}:
slot
port
5-236
A, with a DS3 controller card installed.
Port number or range. Range of ports is 1-2
Axxius 800 - Release 2.2
CLI Commands
status
status (ds3) performance history
Use the status (ds3) performance history command to display performance statistics for the
current 15 minute interval and all previous 15 minute intervals (up to a total of 96) of a DS1.
Syntax: status {ds3-addr} performance
> status a:1 performance history
SLOT A:
Performance Statistics for DS3 Port 1:
Near End Statistics:
UAS SEFS CSES
curr. interval:
0
0
0
totals:
0
CES PSES
0
0
0
0
0
Far End Statistics:
UAS CSES
curr. interval:
0
0
CES
0
CCV
0
totals:
0
0
0
0
PES
0
LES
0
0
0
LCV
0
PCV
0
0
0
0
elapsed time in current 15 min. interval:
valid 15 min. intervals in data:
7:27
0
{ds3-addr}
In the form of {slot port}:
slot
port
Axxius 800 - Release 2.2
A, with a DS3 controller card installed.
Port number or range. Range of ports is 1-2
5-237
CLI Commands
status
status equipment
Use the status equipment command to display current equipment information of the Axxius
800.
Syntax: status equipment [slot]
Example: status equipment
Axxius> status equipment
SLOT P1
SLOT P2
CardType
Status
+24 V
Healthy
Card not installed
SLOT A1
SLOT A2
T3x2
T3x2
SLOT B1
SLOT B2
Card not installed
Card not installed
SLOT
SLOT
SLOT
SLOT
SLOT
SLOT
SLOT
SLOT
TSRx4
T1x4
V35x2
V35x2
BRIx8
OCUDPx1
FXOx8
FXSPSMx1
Example:
1
2
3
4
5
6
7
8
Active
Hot Standby
Present
Not Present
Present
Present
Present
Present
Present
Present
SW Vers
CLEI
SIPUMR0DAA
2.1.0
2.1.0
SIIX60FDAA
SIIX60FDAA
1.03
SIC380XCAA
2.01
2.01
1.11
1.01
1.12
0.01
SIC3HK0CAA
SIC3HK0CAA
SIIXUX0DAA
SIIXA4DDAA
SIIXPV0DAA
status equipment a2
Axxius> status equipment a2
SLOT A2:
Product:
Card Type:
Status:
Card Revision:
BootCode Revision:
SW Revision:
CLEI:
5-238
Axxius 800
Controller with T3x2 Services
Active
A.00
1.6
2.1.0 (build: 6)
SIIX60FDAA
Axxius 800 - Release 2.2
CLI Commands
status
Example: status equipment 3
The example with display the status of the card in slot 4. In this example a TSR
card is in this slot.
> status equipment 3
SLOT 3
CardType:
Status:
SW Revision:
BootCode Version:
FPGA Revision:
CLEI:
TSRx4
Present
1.30H
2.22
1.01
SIL1UW0EAA
[slot]
If a slot number is not entered, the status of the all slots will be displayed.
slot
A for the controller card, or 1-8 for service cards.
status (fxo)
Use the status (fxo) to display the current near-end line status of the specified FXO.
Syntax: status {fxo-addr}
Example: status 5:2
The example displays status of port 2 (FXO) on slot 5.
> status 5:2
FXO
--5:2
Rx AB
----01
Tx AB
----10
Signal=>T1 sig
-------------GS=>GS
T1
----------------Traffic
TP
-N
See Display Descriptions on page 5-231 for definitions of column headings.
{fxo-addr}
slot
port
Axxius 800 - Release 2.2
The slot number (1-8) that contains the FXO card
Port number or range.
5-239
CLI Commands
status
status (fxsPS or fxsPSM)
Use the status (fxsPS or FXS PSM) to display the current near-end line status of the specified
FXS PS or FXS PS card with modem.
Syntax: status {fxsPS-addr|fxsPSM-addr}
Example: status 4:1
The example displays status of port 1 (FXS PS) on slot 4.
> status 4:1
FXS
--4:1
Rx AB
----01
Tx AB
----01
Signal=>T1 Sig T1
TP
-------------- ----------------- -LS => LS
Traffic
N
{fxsPS-addr|fxsPSM-addr}
In the form {slot|slot:port}, since there is only one port the system will display the same
information with either address.
slot
port
Slot number (1-8) of the FXS PS or FXS PSM card
Port number or range.
status ipds0
Use the status ipds0 command to display the current status of the DS0 management channel.
Syntax: status ipds0
Example: status ipds0
> status ipds0
Operational state:
5-240
DOWN
Axxius 800 - Release 2.2
CLI Commands
status
status lsprotect
Use the status lsprotect command to display the current status of the low speed protection
cards.
Syntax: status lsprotect
Example: status lsprotect
> status lsprotect
Low Speed Protection Status:
Low Speed Protection Global Service Enable: ENABLED
Low Speed Protection Operational Status: ENABLED
Relay Card Status, Slot 9: INSTALLED
Backup Slot: 7
Backup Slot Type: Quad T1
Backup Slot Port Status:
PORT: LOS: LCV: XMIT:
1
NO
NO NORM
2
NO
NO NORM
3
NO
NO NORM
4
NO
NO NORM
PRES:
PRES
PRES
PRES
PRES
Protected Port Status:
SLOT: PORT: TYPE: BACKUP: ENABLED: SWITCHMODE: LOCKOUT: LOS: LCV: XMIT:
PRES:
3
1
QT1
NO
NO
MANUAL
N/A
YES NO NORM PRES
3
2
QT1
NO
NO
MANUAL
N/A
YES NO NORM PRES
3
3
QT1
NO
NO
MANUAL
N/A
YES NO NORM PRES
3
4
QT1
NO
NO
MANUAL
N/A
YES NO NORM PRES
5
1
QT1
NO
NO
MANUAL
N/A
YES NO NORM PRES
6
1
QT1
NO
NO
MANUAL
CNT= 2
YES NO NORM PRES
6
2
QT1
NO
NO
MANUAL
CNT= 2
YES NO NORM PRES
6
3
QT1
NO
NO
MANUAL
CNT= 2
YES NO NORM PRES
6
4
QT1
NO
NO
MANUAL
CNT= 2
YES NO NORM PRES
Number of Protected Ports: 9
Axxius 800 - Release 2.2
5-241
CLI Commands
status
status (ocudp)
Use the status (ocudp) command to displaystatus for selftest and loopbacks.
Syntax: status {ocudp-addr}
Example: status 2:1
SLOT 2:
Status for OCUDP Port 1:
Selftest:
Results as of 23:25:48 01/07/2001
Datapath:
PASS
FPGA:
PASS
OCU:
PASS
OCU Manual Loopback:
CSU Manual Loopback:
NONE
NONE
OCU NonLatching Loopback:
DSU NonLatching Loopback:
CSU NonLatching Loopback:
NONE
NONE
NONE
OCU Latching Loopback:
DSU Latching Loopback:
CSU Latching Loopback:
NONE
NONE
NONE
{ocudp-addr}
The {slot:port} address of the OCU-DP card to display.
slot
port
5-242
Slot number (1-8) where the OCU-DP is located
Port number or range.
Axxius 800 - Release 2.2
CLI Commands
status
status (ocudp) performance
Use the status (ocudp) performance command to display performance statistics for the current
15 minute interval, previous 15 minute interval, previous 1 hour interval, and for the previous
day.
Syntax: status {ocudp-addr} performance
Example: status 2:1 performance
> status 2:1 performance
SLOT 2:
Performance Statistics for OCUDP Port 1:
current
previous
15 min.
15 min.
1 hour
1 day
----------- ----------- ----------- ---------out of service seconds:
775
0
0
0
loss of frame seconds:
0
0
0
0
loss of signal seconds:
784
0
0
0
bipolar violations seconds:
0
0
0
0
elapsed time in current 15 min. interval: 13:27
valid 15 min. intervals in hour:
0
valid 15 min. intervals in Day:
0
{ocudp-addr}
The {slot:port} address of the OCU-DP card to display.
slot
port
Axxius 800 - Release 2.2
Slot number (1-8) where the OCU-DP is located
Port number or range.
5-243
CLI Commands
status
status (ocudp) performance history
Use the status (ocudp) performance history command to display performance statistics for the
current 15 minute interval and all previous 15 minute intervals (up to a total of 96).
Syntax: status {ocudp-addr} performance history
Example: status 2:1 performance history
> status 2:1 performance history
SLOT 2:
Performance Statistics for OCUDP Port 1:
curr. interval:
prev. intvl 1:
prev. intvl 2:
totals:
OOS
----248
899
886
=====
2033
BPV
----0
0
0
=====
0
LOF
----0
0
0
=====
0
LOS
----248
900
896
=====
2044
elapsed time in current 15 min. interval:
valid 15 min. intervals in data:
4:14
2
{ocudp-addr}
The OCUDP address is in the form {slot|slot:port}. Where {slot} displays information for
all ports on the card, {slot:port} for only the defined port.
slot
port
5-244
Slot number (1-8) where the ADPCM card is located
Port number, range or all.
Axxius 800 - Release 2.2
CLI Commands
status
status (router)
status (router) alarms
Use the status (router) alarms command to display the current alarm log from the
specified TSR card.
Syntax: status {tsr_card-addr} alarms
Example: status 5 alarms
ROUTER BLADE ALARM LOG REPORT Slot-5
Message
Count
Time
Jan
4 22:26:47.0 Ethernet Link 5:1 Down.
{tsr_card-addr}
The slot number (1-8) that contains the TSR card.
status (router) dns
Use the status (router) dns command to display the current state of DNS resolver and the
entries in the DNS cache.
Syntax: status {tsr_card-addr} dns
Example: status 4 dns
> status 4 dns
ROUTER BLADE DNS RESOLVER REPORT Slot-4
DNS RESOLVER IS ENABLED
My DNS Ip Address 10. 0. 0. 1
My DNS Hostname
Axxius25.test
Primary
DNS Server
Secondary DNS Server
10. 10. 10.
0. 0. 0.
0
0
{tsr_card-addr}
The slot number (1-8) that contains the TSR card.
Axxius 800 - Release 2.2
5-245
CLI Commands
status
status (router) events
Use the status (router) events command to display the current event log from the specified
Router card.
Syntax: status {rtr_card-addr} events
Example: status 5 events
> status 5 events
ROUTER BLADE EVENTS LOG REPORT Slot-5
Time
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Jan
Message
Count
10 0:56:44.8 Download EVE.RPT by Controller
10 0:54:27.4 Download complete in 0.0 secs [17440
10 0:54:27.4 Download ALM.RPT by Controller
10 0:14:23.5 ADMIN login terminated
10 0:14:21.8 Download complete in 0.1 secs [61600
10 0:14:21.7 Download config.cfg by Controller
10 0:14:21.6 Send CFG Change Notice to Controller
10 0:14:20.7 NVRAM Flash Task Wakeup Event Sent
10 0:10:56.5 Login accepted at ADMIN level
10 0:03:29.9 ADMIN login terminated
10 0:03:28.5 Download complete in 0.1 secs [60880
10 0:03:28.4 Download config.cfg by Controller
10 0:03:28.3 Send CFG Change Notice to Controller
10 0:03:27.4 NVRAM Flash Task Wakeup Event Sent
10 0:02:48.7 Login accepted at ADMIN level
9 23:29:34.5 Download complete in 0.1 secs [60160
9 23:29:34.3 Download config.cfg by Controller
9 23:29:34.3 Send CFG Change Notice to Controller
9 23:29:33.4 NVRAM Flash Task Wakeup Event Sent
9 23:28:35.7 Download complete in 0.1 secs [60000
9 23:28:35.5 Download config.cfg by Controller
bps]
bps]
- PASS
bps]
- PASS
bps]
- PASS
bps]
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
5-246
Axxius 800 - Release 2.2
CLI Commands
status
status (router) ip address table
Use the status (router) ip address table command to display the current IP address table
for the specified TSR card.
Syntax: status {tsr_card-addr} ip address table
["profile-name"]
Example: status 5 ip address table
>
status 5 ip address table
ROUTER BLADE IP ADDRESSES REPORT Slot-5
Axxius50 has learned 2 IP Addresses from 1 Port.
Display: <IP Address >
Learned From: <All Ports
Port Name
1.
2.
Local LAN
Local LAN
Static
Direct
>
IP Address
MAC Address
120.0.0.10
192.168.3.196
00E09701E574
Example: status 5 ip address table "Axxius50"
> status 5 ip address table "Axxius50"
ROUTER BLADE IP ADDRESSES REPORT Slot-5
Axxius50 has learned 2 IP Addresses
Display: <IP Address >
Learned From: <Local LAN >
1.
2.
Static
Direct
IP Address
MAC Address
120.0.0.10
192.168.3.196
00E09701E574
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
["profile-name"]
The profile name for the TSR interface that is used to reach this destination. Name must be
enclosed in quotes, with a maximum length of 11 characters.
Axxius 800 - Release 2.2
5-247
CLI Commands
status
status (router) ip network table
Use the status (router) ip network table command to display the current table of learned
IP Networks for the specified interface on the Router card.
Syntax: status {rtr_card-addr} ip network table
["profile-name"]
Example: status 5 ip network table
> status 5 ip network table
ROUTER BLADE IP NETWORKS REPORT Slot-5
Total Entries-3 on 2 Ports
Display: <IP Networks > Learned From: <All Ports
Network
1. Static 200.1.1.0
2. Static 100.0.0.0
3. Direct 192.168.3.0
>
Subnet Mask
Metric Next Gateway
Port Name
255.255.255.0
1
LosAngeles
255.0.0.0
1
192.136.43.52
Local LAN
255.255.255.0
1
192.168.3.196
Local LAN
Example: status 5 ip network table "Axxius50"
> status 5 ip network table "Axxius50"
ROUTER BLADE IP NETWORKS REPORT Slot-5
Total Entries-2 on Local LAN
Display: <IP Networks > Learned From: <Local LAN >
Network
1. Static 100.0.0.0
2. Direct 192.168.3.0
Subnet Mask
255.0.0.0
255.255.255.0
Metric Next Gateway
Frame
1
192.136.43.52
Eth II
1
192.168.3.196
Eth II
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
["profile-name"]
The profile name for the Router interface that is used to reach this destination. Name must
be enclosed in quotes, with a maximum length of 11 characters.
5-248
Axxius 800 - Release 2.2
CLI Commands
status
status (router) ipx network table
Use the status (router) ipx network table command to display the current table of learned
IPX Networks for the specified interface on the Router card.
Syntax: status {rtr_card-addr} ipx network table
["profile-name"]
Example: status 5 ipx network table
> status 5 ipx network table
ROUTER BLADE IPX NETWORKS REPORT Slot-5
Total Entries-4 on 1 Ports
Display: <IPX Networks> Learned From: <All Ports
1.
2.
3.
4.
Network Hops Ticks Next IPX Router
Static 00000011 2
4
Static 00000011 2
4
Static 00000011 2
4
Static 00000011 2
4
>
Port Name Frame Type
LosAngeles
802.3
LosAngeles
802.2
LosAngeles
SNAP
LosAngeles Eth II
Example: status 5 ipx network table "Axxius50"
> status 5 ipx network table "Axxius50"
ROUTER BLADE IPX NETWORKS REPORT Slot-5
Total Entries-0 on Local LAN
Display: <IPX Networks> Learned From: <Local LAN >
Network Hops Ticks
No Records to Display...
Next IPX Router
Frame Type
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
["profile-name"]
The profile name for the Router interface that is used to reach this destination. Name must
be enclosed in quotes, with a maximum length of 11 characters.
Axxius 800 - Release 2.2
5-249
CLI Commands
status
status (router) ipx server table
Use the status (router) ipx server table command to display the current table of learned
IPX Servers for the specified interface on the Router card.
Syntax: status {rtr_card-addr} ipx server table
["profile-name"]
Example: status 4 ipx server table
> status 4 ipx server table
ROUTER BLADE IPX SERVERS REPORT Slot-4
Total Entries-0 on 0 Ports
Display: <IPX Servers > Learned From: <All Ports
Network
Hops Type Name
Port Name
>
Frame Type
No Records to Display...
Example: status 5 ipx server table "Axxius50"
> status 5 ipx server table "Axxius50"
ROUTER BLADE IPX SERVERS REPORT Slot-5
Total Entries-0 on Local LAN
Display: <IPX Servers > Learned From: <Local LAN >
Network
Hops Type Name
Frame Type
No Records to Display...
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
["profile-name"]
The profile name for the Router interface that is used to reach this destination. Name must
be enclosed in quotes, with a maximum length of 11 characters.
5-250
Axxius 800 - Release 2.2
CLI Commands
status
status (router) mac address table
Use the status (router) mac address table command to display the current table of learned
MAC Addresses for the specified interface on the Router card.
Syntax: status {rtr_card-addr} mac address table
["profile-name"]
Example: status 5 mac address table
> status 5 mac address table
ROUTER BLADE MAC ADDRESSES REPORT Slot-5
Axxius50 has learned 2 MAC Addresses from 1 Port.
Display: <MAC Address>
Learned From: <All Ports
1.
2.
Port Name
Local LAN
Local LAN
>
MAC Address
Direct 00E09701E574
Static 00E09700E9CD
Example: status 5 mac address table "Axxius50"
> status 5 mac address table "Axxius50"
ROUTER BLADE MAC ADDRESSES REPORT Slot-5
Axxius50 has learned 2 MAC Addresses
Display: <MAC Address>
Learned From: <Local LAN >
1.
2.
MAC Address
Direct 00E09701E574
Static 00E09700E9CD
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
["profile-name"]
The profile name for the Router interface that is used to reach this destination. Name must
be enclosed in quotes, with a maximum length of 11 characters.
Axxius 800 - Release 2.2
5-251
CLI Commands
status
status (router) performance
Use the status (router) performance command to display the current runtime statistics
from the specified Router card.
Syntax: status {rtr_card-addr} performance
Example: status 5 performance
ROUTER BLADE PERFORMANCE REPORT Slot-5
Run-time Statistics for Axxius50.
LAN Packet Totals:
WAN Packet Totals:
Remote’s
Name
LosAngeles
Received 0
Received 0
Forwarded
to WAN
0 pps
Transmitted 0
Transmitted 0
Errors 0
Errors 0
Throughput
Comp. Ratio
to/from WAN
to/from WAN
0 /0
bps
/
Remote
conns.
0
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
status (router) stp
Use the status (router) stp command to display the current Spanning Tree state from the
specified Router card.
Syntax: status {rtr_card-addr} stp
Example: status 5 stp
ROUTER BLADE SPANNING TREE PROTOCOL REPORT Slot-5
STP Stats
No Enabled STP Ports Detected.
STP View
Bridge Priority: 32768 Address:00E09701E574
Root Priority: 32768 Address:00E09701E574
Root Port: 0 Path Cost 0
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
5-252
Axxius 800 - Release 2.2
CLI Commands
status
status (router-lan)
Use the status (router-lan) command to display the current Router status information.
Syntax: status {rtr_lan-addr)
Example: status 3:1
The example displays status of the Router card in slot 3.
> status 3:1
SLOT 3:
Status for TSR Card
Run Status:
PORT 1
TELNET:
TRANSMIT:
RECEIVE:
RS-232
UP
YES
YES
PORT 2
TELNET:
TRANSMIT:
RECEIVE:
RS-232
UP
YES
YES
PORT 3
TELNET:
TRANSMIT:
RECEIVE:
RS-232
UP
YES
YES
PORT 4
TELNET:
TRANSMIT:
RECEIVE:
RS-232
UP
YES
YES
Running
{rtr_lan-addr}
The Router address is in the form {slot:port|slot "profile-name"}.
slot
port
profile-name
Axxius 800 - Release 2.2
The slot number (1-8) that contains the Router card.
Port number, or all.
Existing LAN identifier, enclosed in quotes.
5-253
CLI Commands
status
status (router-trunk)
Use the status (router-trunk) command to display the current status information for the
specified Trunk on the Router card.
Syntax: status {rtr_trunk-addr)
Example: status 3:1:1-4
> status 3:1:1-4
SLOT 3:
Status for TSR 1
Link Alarm:
SLOT 3:
Status for TSR 1
Link Alarm:
SLOT 3:
Status for TSR 1
Link Alarm:
SLOT 3:
Status for TSR 1
Link Alarm:
Trunk 1:
NO
Trunk 2:
NO
Trunk 3:
NO
Trunk 4:
NO
{rtr_trunk-addr}
The Router trunk address is in the form {slot:port:trunk}.
slot
port
trunk
5-254
The slot number (1-8) that contains the Router card.
Port number of the Router.
Trunk number, a range or "all" can be used here. Port numbers are 1-24.
Axxius 800 - Release 2.2
CLI Commands
status
status sessions
Use the status sessions command to display the current status of all active CLI sessions.
Syntax: status sessions
Example: status sessions
> status sessions
Session
------* TELNET1
User
---paul
Login Port
---------192.168.1.1
* indicates current session
Axxius 800 - Release 2.2
5-255
CLI Commands
status
status (v54)
Use the status (v54) to display the current near-end line status of the V.54 card.
Syntax: status {v54-addr}
Example: status 3:all
The example displays status of all ports (V.54) on slot 3.
> status 3:all
SLOT 3:
Status for V35 PORT 1:
DCD:
Low
CTS:
Low
DSR:
Low
RTS:
Low
DTR:
Low
BERT:
N/A
SLOT 3:
Status for V35 PORT 2:
DCD:
Low
CTS:
Low
DSR:
Low
RTS:
Low
DTR:
Low
BERT:
N/A
{v54-addr}
slot
port
The slot number (1-8) that contains the V.54 card
Port number or range.
Display Descriptions
DCD CTS DSR RTS DTR BERT -
5-256
Data Carrier Detect indicates port is receiving a carrier signal
Clear to Send indicates port is ready to receive data
Data Set Ready indicates port is ready to send data
Request to Send
Data Terminal Ready
Bit Error Rate Test
Axxius 800 - Release 2.2
CLI Commands
store
store
The store command is used to upload a software file from a defined slot to a defined location
on a PC, via TFTP. Currently uploads for general use are only permitted for the Controller and
TSR card configuration files.
Syntax: store {number} tftp {ip-addr} {"file-name"}
Example: store 5 tftp 192.168.2.35 "d:\AxxiusBackup\file.cfg"
Filename: d:\AxxiusBackup\file.cfg
Source IP Address: 198.162.3.196
Target IP Address: 192.168.43.52
Source Card Slot:
5
Source Card Type:
tsrx1
’store tftp’ will be executed with the above parameters.
A TFTP server must be running on the host system.
Do you really want to do this? y
Card software download in progress. Please be patient...
Software transfer command completed.
{number}
Slot number (1 to 8) that you are uploading the software from.
{ip-addr}
Host IP address in the form of xxx.xxx.xxx.xxx, where xxx is a number from 1 to 255. If
not supplied, the host IP address from the database will be used.
{"file-name"}
This will name the configuration file that you are storing. File must be a .cfg file and
enclosed in quotes.
Axxius 800 - Release 2.2
5-257
CLI Commands
switch
switch
switch activeimage
Use the switch activeimage command to switch the active with the backup application images
stored in a Controller or Router card.
Syntax: switch [rtr_card-addr] activeimage
Example: switch activeimage
> switch activeimage
Do you really want to do this? y
OK
[rtr_card-addr] - The Router card slot number (1 - 8) to retrieve the image information
from. Note: If no slot number is entered, the image information is retrieved from the
Controller.
switch controller
Use the switch controller command to switch to the standby controller.
Note: for redundant Axxius systems only.
Syntax: switch controller
Example: switch controller
> switch controller
Do you really want to do this? y
Standby controller not found.
5-258
Switch Command Canceled!
Axxius 800 - Release 2.2
CLI Commands
switch
switch (ds3)
Use the switch (ds3) command to switch to the standby DS3 port.
Note: for redundant Axxius systems only.
Syntax: switch {ds3-addr}
Example: switch a:1
> switch a:1
Do you really want to do this? y
OK
{ds3-addr}
In the form of {slot port}:
slot
port
Axxius 800 - Release 2.2
A for the controller card
Port number (1 or 2).
5-259
CLI Commands
telnet
telnet
telnet (router)
Use the telnet (router) command to establish a Telnet session from the Axxius 800 CLI to the
Router card menu-driven user interface.
Syntax: telnet {rtr_lan-addr}
Example: telnet 3
The example will Telnet into a TSR in Slot 3.
> telnet 3
Connected.
Escape character is ’^]’.
Attempting Carrier Access Router connection...
Router [Wed Apr 24, 2002 13:00:15] (<CR> to login)
Password >******
Select a terminal type...
(<space> or <back-space> to toggle, <CR> to accept)
Terminal: <VT100>
{rtr_lan-addr}
The Router address is in the form {slot:port|slot "profile-name"}}.
slot
port
profile-name
5-260
The slot number (1-8) that contains the Router card.
Port number of the Router.
Existing WAN identifier, enclosed in quotes.
Axxius 800 - Release 2.2
CLI Commands
trace route
trace route
tracert (router)
Use the tracert (router) command to invoke a Trace Route to a host device on a network of a
particular TSR Router. Trace Route responses will be returned to user screen as each hop host
device response packet is received or the timeout return data is provided for a hop. The output
will have DNS names only if DNS resolver is enabled and DNS server can resolve host IP. The
optional parameters [ttlbeg] and [ttlmax] allot the user to define the range of hops the trace route
will query. An response with an * indicates no response from the host.
Syntax: tracert {rtr_card-addr} {ip-addr|"domain-name"}
[type] [src-ip] [ttlbeg] [ttlmax] [udp-port]
Example: tracert 2 10.40.15.70 udp
Example: tracert 3 ""www.google.com" ICMP 192.168.100.100 1 32
Tracert 3 www.google.com 192.168.100.100 5 32 in progress…
Hops Ave.
Host
1
<10 ms 99.90.9.254 nat1xt-tw-gw.carrieraccess.com
2
<10 ms 65.243.6.17
3
10 ms 137.39.6.200
4
20 ms 152.63.101.134 0.so-3-1-0.XL2.DFW9.ALTER.NET
5
20 ms 152.63.102.6 0.so-0-0-0.XR2.DFW9.ALTER.NET
6
10 ms 152.63.100.221 184.ATM7-0.BR4.DFW9.ALTER.NET
7
*
*
8
10 ms 208.172.130.104 agr4-loopback.Dallas.cw.net
9
10 ms 208.172.139.9 dcr1-so-0-2-0.Dallas.cw.net
10
580 ms 216.33.153.188 csr1-ve241.SantaClarasc3.cw.net
11
60 ms 64.68.64.210
this.is.an.device.name.2.long.2show.all.of.name...
12
70 ms 216.239.47.2
13
60 ms 216.239.33.101 www.google.com
Trace Terminated: 13 Hops, Hop range 1-13
{rtr_card-addr}
The slot number (1-8) that contains the Router card.
Axxius 800 - Release 2.2
5-261
CLI Commands
trace route
{ip-addr|"domain-name"}
ip-addr
domain-name
The IP address for trace route to use for this query, in the form of
xxx.xxx.xxx.xxx, where xxx is between 0-255.
The domain name for the external DNS server. Name must be
enclosed in quotes, with a maximum length of 42 characters.
[type]
icmp
udp
Internet Control Message Protocol (ICMP) method of trace routing is
the most widely used and has the best reliability. This is the default.
User Datagram Protocol (UDP) method requires that all devices in
the chain of the trace route support probes on the particular UDP
port. This method is not recommended.
[src-ip]
This optional parameter, only applies it [type] is set to ICMP. This defines the source IP
address in the ICMP echo request and must be one of the router interface IP addresses.
Default is to use the IP address of the interface from which the ping is sent.
[ttlbeg]
This optional parameter allows the user to define the beginning (or the minimum) of the
range of hops the trace route will query. Range is 1 - [ttlmax] value. Default is 1.
[ttlmax]
This optional parameter allows the user to define the end (or the maximum) of the range of
hops the trace route will query. Range is [ttlbeg] - 255 value. Default is 30.
[udp-port]
This optional parameter only applies if [type] is set to UDP. Range is 1 - 65535, with a
default of 33434.
5-262
Axxius 800 - Release 2.2
CHAPTER
DS1 Controller Card
In this Chapter
n
Overview
n
Features
n
Technical Specifications
n
Configuration
n
Built-In Card Handles
n
LEDs
DS1 Controller Card
Overview
Overview
The Quad port DS1 Controller card drives the Axxius 800 Access Integration Platform,
delivering a cost-effective, compact solution enabling wireless service providers to
optimize cell site access facilities, rescue up to 35% of stranded cell sit bandwidth and
deliver additional revenue generating services at dramatically lower costs.
The DS1 Controller card features 4 DS1 ports with integrated CSUs and a built-in 1/0
cross-connect matrix. This provides full, non-blocking connectivity between the
Controller and any of the 8 Service card slots. The Controller connects to the control
panel unit for physical termination of the on-board DS1 circuits, as well as access to
the RS-232 and Ethernet management interfaces.
The DS1 Controller card manages all the other Axxius Service cards providing the
physical, electrical and logical connections to deliver a complete wireless cell site
solution.
The DS1 Controller card has several local and remote management options available.
Front-panel LEDs quickly communicate alarm, system and line status. The card can be
configured and managed locally through the RS-232 or Ethernet management
connections on the Control Panel using a Command Line Interface (CLI).
A number of remote management options are available to reduce truck roll costs for
most maintenance and troubleshooting activities. The in-band DS0 management
channel on the Controller delivers 64 Kbps remote access to the Axxius without
incurring additional facility costs. Alternatively, a separate Ethernet facility can be
deployed to support out-of-band SNMP network management and the Controller can
also be accessed through the V.34 dial-in modem connection from the Order Wire
POTS with Modem Service card.
NOTE: Removing an active Controller is not recommended, use the
switch controller command to change the Active Controller to Standby and
then remove the Controller card.
6-2
Axxius 800 - Release 2.2
DS1 Controller Card
Features
Features
l Rescues up to 35% or more of network bandwidth commonly wasted at the cell
l
l
l
l
l
l
l
site or when providing fractional T1 service
Provides full, non-blocking DS0 cross-connect connectivity between the DS1
Controller card and any of the eight service card slots
Supports up to 36 T1 ports
Performs framing and coding conversion between T1 ports
Features an integrated 1/0 digital cross-connect for service grooming and
provisioning
Four DS1 ports built into the Controller terminate multiple network connections
and support drop-and-insert applications
Software selectable DS1 or DSX interfaces
Enables remote SNMP, or Telnet provisioning, performance monitoring, and
testing of services and network conditions
Axxius 800 - Release 2.2
6-3
DS1 Controller Card
Technical Specifications
Technical Specifications
Product Includes
l Built-in non-blocking 1/0 Digital Cross-connect System for up to 36 T1 ports
l Robbed-bit (voice) and clear channel (data) signaling on the same DS1
l Integral quad T1 ports that support drop-and-insert applications
l T1.231 performance monitoring statistics: 96 15-minute segments
l
l
l
l
l
(24 hour period)
Performance report messages
Front-panel LED indicators for DS1 status, major and minor alarms, and alarm
cut-off status are located on the Control Panel Interface card
Controller support for Terminal Server Router card code download through its
Ethernet management port
Configurations automatically stored in non-volatile memory
SNMP agent, supporting MIB objects:
- RFC 1213 (MIB-II)
- RFC 1659 (V.35)
- RFC 1907 (SNMPv2-MIB)
- RFC 2011 (IP-MIB)
6-4
- RFC 2233 (IF-MIB)
- RFC 2494 (DS0-MIB)
- RFC 2495 (DS1/E1-MIB)
Axxius 800 - Release 2.2
DS1 Controller Card
Technical Specifications
Management
l Local
l
l
l
l
- RS-232 craft port interface drives up to 50 ft. (15.24 m) cable, and provides a
Command Line Interface (CLI) using ASCII terminal or PC with terminal
emulation software, modem using XMODEM or PPP sessions
Remote
- 10/100Base-TX Ethernet management port provides
• Local IP management connectivity
• RJ-45 connector
• 10/100Base-TX Ethernet link LED status indicator
• IP management over a dedicated DS0 bearer channel
- CLI management via the V.34 modem port on the Single Channel POTS with
Modem Service card
Integrated TFTP client for remote download of Controller software upgrades
SNMP agent for use with SNMP-based Element Management Systems
CLI offers three levels of password controlled security
DS1 Interface
l Selectable four DS1 ports from the Connector Panel operating at 1.544 Mbps
l
l
l
l
l
l
l
± 50 bps
4 DS1 ports operating at 1.544 Mbps
Expansion to 36 DS1 ports in a single chassis using Quad DS1 Service Cards
SF (D4) and ESF framing, AMI or B8ZS line coding (DS1 operation)
Short-haul or long-haul loop settings for DS1
4 RJ-48C connectors located on the front of the Control Panel Interface Card
Integrates DS1 CSU functionality for direct connection to DS1 lines
Offers secondary solid-state fuseless protection to lightning and power cross
incidents.
Axxius 800 - Release 2.2
6-5
DS1 Controller Card
Technical Specifications
Service Interfaces Supported
l Dual V.35/.54 Service card (hardened)
l FXO Voice Service card
l ISDN BRI Service card
l OCU-DP Service card
l Quad DS1 ADPCM Service card (hardened)
l Quad T1 Service card (hardened)
l Single Channel POTS Service card (hardened)
l Single Channel POTS with Modem Service card
l Terminal Server Router (TSR) card (hardened)
Network Standards
l AT&T Pub 54016, TR 62411
l ANSI T1-403, T1.102, T1.231
l ITU G.703, G.704
l TBR 12 and 13
Clocking
l Loop-timed from any DS1
l External from BITS clock input (T1.101, T1.102 signal type)
l Revertive or non-revertive (provisionable) clock switching provides automatic
backup to secondary DS1 should the primary DS1 fail
l Operates as a Stratum 4E device as defined by Telcordia GR-1244-CORE and
AT&T TR 62411
6-6
Axxius 800 - Release 2.2
DS1 Controller Card
Technical Specifications
Alarms
l Three visible alarm outputs, critical, major and minor
l Three audible alarm outputs, critical, major and minor
l Alarm Cut-Off for audible alarm outputs
l Ten external alarm inputs (user definable)
l Alarm contacts accessible from external alarm connector
l All alarms are logged in an event log
l Loss of power triggers minor alarm
l Generates SNMP traps for alarming (MIB objects)
Testing and Diagnostics
l Standard T1 line and payload loopbacks
l Local loopback
l T1.231 performance history
Power Consumption
l 6 W maximum
Environment
In addition to the systems environment requirements, the following applies to the
DS1 Controller card. For additional information see Installation Environment” on
page 2-3.
l Operating temperature range of the DS1 Controller card: -40° to 149° F
(-40° to 65° C)
Physical
l Dimensions: 3.5 in. (H) x 0.75 in. (W) x 11.25 in. (D)
8.9 cm (H) x 1.9 cm (W) x 28.6 cm (D)
l Weight: 10.2 oz. (0.29 kg)
Axxius 800 - Release 2.2
6-7
DS1 Controller Card
Controller Active and Standby
Controller Active and Standby
The Axxius 800 can function fully with a single Controller card, however Controller
redundancy is available with two like Controllers (DS1 or DS3) installed. When two
Controllers are installed in a system, one is always Active and the other is Standby. The
Standby can have 2 conditions:
l Hot Standby - meaning that the card is ready to take over for the active and the
switch will not affect service
l Cold Standby - meaning that the card is ready to go active (healthy) but for some
reason (code of the 2 controllers is not the same) it will need to reconfigure the
box when it goes active, which will be service affecting.
There are two ways to identify the status of the Controllers.
1. CLI Command status equipment
> status equipment
CardType
Status
+24 V
Healthy
Card not installed
SW Vers
SLOT P1
SLOT P2
SLOT A1
SLOT A2
T1x4
T1x4
1.1.0
1.1.0
SIIX4W0DAA
SIIX4W0DAA
SLOT B1
SLOT B2
Card not installed
Card not installed
1.00
1.73
2.01
2.01
1.11
1.01
1.12
0.01
NOT AVAIL
SIIXFWBDAA
SIC3HK0CAA
SIC3HK0CAA
SIIXUX0DAA
SIIXA4DDAA
SIIXPV0DAA
SLOT
SLOT
SLOT
SLOT
SLOT
SLOT
SLOT
SLOT
SLOT
1
2
3
4
5
6
7
8
9
Active
Hot Standby
TSRx4
Present
T1x4
Present
V35x2
Present
V35x2
Present
BRIx8
Present
OCUDPx1
Present
FXOx8
Present
FXSPSMx1
Present
Card not installed
CLEI
SIPUMR0DAA
2. Visually looking at the Controller cards.
Active - STAT LED will be solid green.
Hot Standby - STAT LED will be solid yellow
Cold Standby - STAT LED will be flashing yellow
6-8
Axxius 800 - Release 2.2
DS1 Controller Card
Configuration
Configuration
Options on the Quad DS1 Controller card are set by the Command Line Interface
(CLI). Note: the faceplate state DS1/E1 Controller, the E1 feature is not supported on
this release.
CLI Commands
The following commands are used to configure the Quad DS1 Controller card. For
detailed information on these commands, see Chapter 5, CLI Commands.
l
l
l
l
l
l
l
l
l
l
connect
Creates two-way connections between channels
disconnect
Removes a connection created by the connect command
set clock (1 and 2)
Sets the primary and secondary transmit clock
set date
Sets the date for the system
set (ds1)
Sets up the DS1 interfaces (up, down, BP violation, FDL, framing, ID string,
line build out, line loopup, linecode, loopdetect, payload, threshold)
set ipds0
Sets up the DS0 management channel (assign, disable, down, IP address, up)
show (ds1)
Displays current settings for DS1 (circuit ID, up, down, framing, line
coding, clock source, line build out, loop code detection, loop back, FDL
type)
show ipds0
Displays the settings for the DS0 management channel
status (ds1)
Displays the status of the DS1 (receive, transmit, loopback)
status ipds0
Display the status of the DS0 management channel
Axxius 800 - Release 2.2
6-9
DS1 Controller Card
Built-In Card Handles
Built-In Card Handles
The Controller card is designed with a handle built into the faceplate to assist in the
removal of the card from the chassis. This handle slides out away from the unit,
creating a handle for a more effective grip.
LEDs
The DS1 Controller has a set of six LEDs. The table below describes each LED.
LED
State
Description
STAT
Green
Active
Red
Failed
Flashing Red
System Reset
Yellow
Hot Standby
Flashing Yellow
Cold Standby
Alternating
Red/Yellow
Application Loading
Off
Port Shutdown
Green
Good Line
Slow Blink Green
Loopback
Red
LOS
Slow Blink Red
LOF, AIS
Fast Blink Red
Card Failure
Yellow
Code Violation
Slow Blink
Yellow
RAI
LINE
STAT
(1-4)
6-10
Axxius 800 - Release 2.2
CHAPTER
DS3 Controller Card
In this Chapter
n
Overview
n
Features
n
Technical Specifications
n
Configuration
n
Built-In Card Handles
n
LEDs
DS3 Controller Card
Overview
Overview
The Dual port DS3 Controller card drives the Axxius 800 Access Integration Platform,
delivering a cost-effective, compact solution enabling wireless service providers to
optimize cell site access facilities, rescue up to 35% of stranded cell sit bandwidth and
deliver additional revenue generating services at dramatically lower costs.
The DS3 Controller card features 2 DS3 ports with integrated 3/1/0 cross-connect
matrix. This provides full, non-blocking connectivity between the DS3 Controller and
any of the 8 Service card slots, enabling the Axxius to operate as both a service delivery
platform at the cell site and as a small M13 multiplexer delivering T1/FT1 tributaries
to remote cell site locations. The DS3 Controller connects to the control panel unit for
physical termination of the on-board DS3 circuits, as well as access to the RS-232 and
Ethernet management interfaces.
The DS3 Controller card manages all the other Axxius Service cards providing the
physical, electrical and logical connections to deliver a complete wireless cell site
solution.
The DS3 Controller card has several local and remote management options available.
Front-panel LEDs quickly communicate alarm, system and DS3 line status. The card
can be configured and managed locally through the RS-232 or Ethernet management
connections on the Control Panel using a Command Line Interface (CLI).
A number of remote management options are available to reduce truck roll costs for
most maintenance and troubleshooting activities. The in-band DS0 management
channel on the Controller delivers 64 Kbps remote access to the Axxius without
incurring additional facility costs. Alternatively, a separate Ethernet facility can be
deployed to support out-of-band SNMP network management and the Controller can
also be accessed through the V.34 dial-in modem connection from the Order Wire
POTS with Modem Service card. Remote configuration, monitoring, maintenance and
troubleshooting tasks are further simplified from the central Network Operation Center
(NOC) using the graphical interfaces of the NetworkValet.
NOTE: Removing an active Controller is not recommended, use the
switch controller command to change the Active Controller to Standby and
then remove the Controller card.
7-2
Axxius 800 - Release 2.2
DS3 Controller Card
Features
Features
l 2 DS3 ports built into the Controller deliver bandwidth to the resident cell site for
l
l
l
l
service delivery applications and distribute residual bandwidth to remote cell
sites
Rescues up to 35% of network bandwidth commonly stranded at the cell sites
Provides full, non-blocking connectivity between the DS3 Controller card and
any of the 8 service card slots
Features an integrated 3/1/0 digital cross-connect for service grooming and
restoration
Enables remote SNMP, EMS or Telnet provisioning, monitoring and testing of
services and network conditions.
Technical Specifications
Product Includes
l Built-in non-blocking 3/1/0 Digital Cross-connect System
l Robbed-bit (voice) and clear channel (data) signaling on the same DS3
l Integral dual DS3 ports that support drop-and-insert applications
l RFC 2496 performance monitoring statistics: Ninety-six 15 minute segments
l
l
l
l
l
(24 hour period)
Performance Report Messages
Front-panel LED indicators for DS3 system and line status
Controller support for Terminal Server Router card code download through its
Ethernet management port
Configurations automatically stored in non-volatile memory
SNMP agent, supporting MIB objects:
- RFC 1213 (MIB-II)
- RFC 1659 (V.35)
- RFC 1907 (SNMPv2-MIB)
- RFC 2011 (IP-MIB)
Axxius 800 - Release 2.2
- RFC 2233 (IF-MIB)
- RFC 2494 (DS0-MIB)
- RFC 2496 (DS3-MIB)
7-3
DS3 Controller Card
Technical Specifications
Management
l Local
- RS-232 craft port interface drives up to 50 ft. (15.24 m) cable, and provides a
Command Line Interface (CLI) using ASCII terminal or PC with terminal
emulation software, modem using XMODEM or PPP sessions
l Remote
- 10/100Base-TX Ethernet management port provides
• Local IP management connectivity
• RJ-45 connector
• 10/100Base-TX link LED status indicator
• IP management over a dedicated DS0 bearer channel
- CLI management via the V.34 modem port on the Order Wire Single Channel
POTS with Modem Service card
- GUI management from NetworkValet EMS
l Integrated TFTP client for remote download of controller software upgrades
l SNMP agent for use with NetworkValet
l CLI offers three levels of password controlled security
Network DS3 Interface
l Line Rate: 44.746 Mbps ± 20 ppm
l Line Code: B3ZS Bipolar with three zero substitution
l Framing format: M23 and C-bit parity
l Transmit impedance: 75 Ω ± 5%, unbalanced
l Transmit jitter attenuation: Meets ANSI T1.102 requirements
l Transmit amplitude: Meets ANSI T1.102 pulse mask with 0.36 to 0.85 Vp
requirements
l Transmit length (cable): 500 ft. (152.4 m) to crossconnect
l Receive sensitivity: -10 dB w/r DSX-3 120 mVp to 900 mVp input range with
automatic gain control circuit
7-4
Axxius 800 - Release 2.2
DS3 Controller Card
Technical Specifications
Service Interfaces Supported
l Dual V.35/.54 Service card (hardened)
l FXO Voice Service card
l ISDN BRI Service card
l OCU-DP Service card
l Quad DS1 ADPCM Service card (hardened)
l Quad T1 Service card (hardened)
l Single Channel POTS Service card (hardened)
l Single Channel POTS with Modem Service card
l Terminal Server Router (TSR) card (hardened)
Network Standards
l ANSI T1-403 and T1.404
Clocking
l Loop-timed from any DS1 within the DS3
l External BITS clock
l Revertive or non-revertive (provisionable) clock switching provides automatic
backup to secondary DS3 should the primary DS3 fail
l Operates as a Stratum 4E device as defined by Telcordia GR-1244-CORE and
AT&T TR 62411
Alarms
l Three visible alarm outputs, critical, major and minor
l Three audible alarm outputs, critical, major and minor
l Alarm Cut-Off for audible alarm outputs
l Ten alarm inputs
l Alarm contacts accessible from external alarm connector
l All alarms are logged in an event log
l Loss of power triggers minor alarm
l Generates SNMP traps for alarming (MIB objects)
Axxius 800 - Release 2.2
7-5
DS3 Controller Card
Technical Specifications
Testing and Diagnostics
l Supports maintenance signals specified in ANSI T1.404 (Section 7.1)
l Standard DS3 line and payload loopbacks
l RFC 2496 performance history
Power Consumption
l 10 W maximum
Environment
In addition to the systems environment requirements, the following applies to the DS3
Controller card. For additional information see Installation Environment on page 2-3.
l Operating temperature range of the DS3 Controller card: -40° to 149° F
(-40° to 65° C)
Physical
l Dimensions: 3.5 in. (H) x 0.75 in. (W) x 11.25 in. (D)
8.9 cm (H) x 1.9 cm (W) x 28.6 cm (D)
l Weight: 10.2 oz. (0.29 kg)
7-6
Axxius 800 - Release 2.2
DS3 Controller Card
Controller Active and Standby
Controller Active and Standby
The Axxius 800 can function fully with a single Controller card, however Controller
redundancy is available with two like Controllers (DS1 or DS3) installed. When two
Controllers are installed in a system, one is always Active and the other is Standby. The
Standby can have 2 conditions:
l Hot Standby - meaning that the card is ready to take over for the active and the
switch will not affect service
l Cold Standby - meaning that the card is ready to go active (healthy) but for some
reason (code of the 2 controllers is not the same) it will need to reconfigure the
box when it goes active, which will be service affecting.
There are two ways to identify the status of the Controllers.
1. CLI Command status equipment
> status equipment
SLOT P1
SLOT P2
CardType
Status
+24 V
Healthy
Card not installed
SLOT A1
SLOT A2
T3x4
T3x4
SLOT B1
SLOT B2
Card not installed
Card not installed
SLOT
SLOT
SLOT
SLOT
SLOT
SLOT
SLOT
SLOT
SLOT
1
2
3
4
5
6
7
8
9
Active
Hot Standby
TSRx4
Present
T1x4
Present
V35x2
Present
V35x2
Present
BRIx8
Present
OCUDPx1
Present
FXOx8
Present
FXSPSMx1
Present
Card not installed
SW Vers
1.1.0
1.1.0
1.00
1.73
2.01
2.01
1.11
1.01
1.12
0.01
CLEI
SIPUMR0DAA
SIIX4W0DAA
SIIX4W0DAA
NOT AVAIL
SIIXFWBDAA
SIC3HK0CAA
SIC3HK0CAA
SIIXUX0DAA
SIIXA4DDAA
SIIXPV0DAA
2. Visually looking at the Controller cards.
Active - STAT LED will be solid green.
Hot Standby - STAT LED will be solid yellow
Cold Standby - STAT LED will be flashing yellow
Axxius 800 - Release 2.2
7-7
DS3 Controller Card
Controller and DS3 Redundancy
Controller and DS3 Redundancy
Protection Modes
The Axxius 800 can be provisioned with one or two DS3 Controller cards and
connections to one or two DS3 lines, which will provide the following levels of
protection:
l Electronics Protection – when provisioned with two Controller cards and only
one DS3 line, only the Controller cards can be protected
l Network Protection – when provisioned with one Controller and two
independent DS3 lines, only the DS3 lines can be protected.
l Electronics and Network Protection – when provisioned with two Controller
cards and two independent DS3 lines, both the controller cards and the DS3 lines
can be protected
Electronics Protection Mode
In this mode there are two DS3 Controllers installed the Axxius 800, but only one DS3
line connected.
The electronics mode of protection provides Controller card redundancy. Because there
is only one DS3 connected, there is no DS3 redundancy. The receive path from the DS3
line is simultaneously applied to the receiver of both Controller cards (see Figure). This
enables both controllers to monitor the condition of the DS3 line so both are
continuously framed up to the incoming signal. The Controller-select signal disables
the outputs of the low-speed receive paths on the standby Controller and enables the
low-speed receive paths on the active controller. The active Controller’s transmit signal
is connected to the transmit path of the DS3 line through a relay, while the standby is
disconnected until a protection switch occurs.
The automatic redundancy mode is used to enable and disable protection switching. If
the redundancy control process determines the active controller is malfunctioning, or a
maintenance switch is invoked (the switch command), a protection switch will occur.
This means that the active Controller relinquishes control to the secondary Controller.
This is done by enabling the standby Controller’s receive path and disabling the
originally active Controller’s low-speed receive path (Controller-select signal) and
7-8
Axxius 800 - Release 2.2
DS3 Controller Card
Controller and DS3 Redundancy
switching the output paths so that the transmit path of the DS3 line is connected to the
standby Controller. Service interruptions (hits) will be taken on both the DS3 and lowspeed connections during this type of switch. However, since the standby Controller is
already framed up to the incoming signal, the hits are minimal.
Electronics Protection Mode
28/21 LS
XMT Stream
DS3OUT+
28/21 LS
RCV Stream
Active
(Primary)
M13 Mux
Controller
xmt
rcv
Primary
DS3
DS3IN+
Enable
28/21 LS
XMT Stream
DS3OUT+
28/21 LS
RCV Stream
Standby
(Secondary)
M13 Mux
Controller
DS3IN+
Disable
Controller
Select
Electronics Protection Mode of the Axxius DS3
The Axxius does not provide a non-revertive mode in electronic protection. No
automatic switchback will occur (as with a revertive Network Protection), but if the
currently active Controller malfunctions, etc. another protection switch will occur if the
mate is in a standby mode.
Axxius 800 - Release 2.2
7-9
DS3 Controller Card
Controller and DS3 Redundancy
Network Protection Mode
The network mode of protection requires a single Controller with two independent DS3
channels. The cross connects are set up identically for both DS3s. Both revertive and
non-revertive modes are applicable. Two DS3 framers are present on the DS3
Controller card. Both are framed to their respective incoming data. Backplane data is
sent to both transmitters and is sent out both interfaces. On loss of signal or high bit
error rate, software will switch from Primary to Secondary interface. In revertive
mode, if the signal returns to the Primary interface or the BERT level is restored for a
period of time, software will return control to the Primary interface. In non-revertive
mode, return to the Primary interface would be by command only or if the secondary
line fails and the primary has returned to normal operation.
Electronics and Network Protection Mode
The highest level of protection, electronics and network protection, allows both the
Controller cards and the DS3 lines to be switched. This mode is available with two
Controllers and two active DS3 lines. Network protection switching must be enabled
and cross connects set up. In this mode, the primary Controller is connected to the both
the primary DS3 line and the secondary DS3 lines (TX and RX). The low-speed
transmit streams are multiplexed, framed and simultaneously broadcast on both the
primary and secondary DS3 lines, thus transmitting the identical payload to the far-end
service and protection line. Also, each Controller is framed up to both its DS3 lines
and the Controller select signal determines which Controller has access to the lowspeed cards, and thus carries the service.
If the active Controller malfunctions, if the DS3 line condition deteriorates, or a
maintenance switch is invoked (the switch command), a protection switch will occur in
the Axxius DS3, which enables the secondary DS3 path through the other Controller
card. If revertive switching is enabled after a five minute delay (beginning when the
previously-active controller’s error rate equals zero) the Axxius DS3 will switch back
to the previously-active Controller and DS3 line, if there is no longer a malfunction in
that path during the five-minute delay. If revertive switching is not enabled no switchback will occur.
NOTE: After a switching event in revertive mode, switching cannot occur
again until the original Controller and DS3 line have experienced 5 minutes
of error-free operation. The 5-minute delay is built-in, and conforms to
standards to prevent oscillation during poor DS3 line conditions.
7-10
Axxius 800 - Release 2.2
DS3 Controller Card
Configuration
Configuration
Options on the DS3 Controller card are set by the following CLI commands.
CLI Commands
The following commands are used to configure the DS3 Controller card. For detailed
information on these commands, see Chapter 5, CLI Commands.
l
l
l
l
l
l
l
l
l
l
l
connect
Creates two-way connections between channels
disconnect
Removes a connection created by the connect command
set clock
Sets the signal clock switching
set clock (1 and 2)
Sets the primary and secondary transmit clock
set date
Sets the date for the system
set (ds3)
Sets up the DS3 interfaces (up, down, berthreshold, clock, dejitter,
equipment, facility ID, frame, framing, generator number, ID, line loopup,
location ID, loopdetect, payload, port number, protect, reversion, threshold,
unit ID)
set ipds0
Sets up the DS0 management channel (assign, disable, down, IP address, up)
show (ds3)
Displays current settings for a DS3
show ipds0
Displays the settings for the DS0 management channel
status (ds3)
Displays the status of the DS3 (receive, transmit, loopback)
status ipds0
Display the status of the DS0 management channel
Axxius 800 - Release 2.2
7-11
DS3 Controller Card
Built-In Card Handles
Built-In Card Handles
The Controller card is designed with a handle built into the faceplate to assist in the
removal of the card from the chassis. This handle slides out away from the unit,
creating a handle for a more effective grip.
LEDs
The DS3 Controller has a set of six LEDs. The table below describes each LED.
LED
State
Description
STAT
Green
Active
Red
Failed
Flashing Red
System Reset
Yellow
Hot Standby
Flashing Yellow
Cold Standby
Alternating
Red/Yellow
Application Loading
Off
NO transport or port shutdown
Green
Good Line
Slow Blink Green
Loopback
Red
LOS
Slow Blink Red
LOF, AIS
Fast Blink Red
Card Failure
Yellow
Standby, when path protection is active
Slow Blink
Yellow
RAI, IDLE, or if protection is active
Out-of-Service
LINE
STAT
(1-2)
3-4 are not
used on this
card
7-12
Axxius 800 - Release 2.2
CHAPTER
FXO Voice Card
In this Chapter
n
Overview
n
Features
n
Technical Specifications
n
Card Configuration
-
CLI Commands
DIP Switch Settings
n
LEDs
n
Channel Associated Signaling (CAS)
Conversions
FXO Voice Card
Overview
Overview
The FXO Voice Service card provides high-density provisioning of reliable Foreign
Exchange Office (FXO) or Direct Inward Dialing (DID) telephone services. Eight FXO
or Dial Pulse Terminate (DPT) telephone line channels can be deployed on each FXO
Service card. These cards can be inserted into any of the eight service card slots of the
Axxius 800 Access Integration Platform. This allows the provisioning of up to 64 FXO
or DPT lines in a single Axxius 800 chassis.
The FXO function sinks battery current and detects ringing voltage originating from
the central office or PBX line, enabling the transport of dial tone and calling features
to remote locations. When configured as a DPT interface, the channels sink and detect
forward and reverse line current, emulating the functions of a central office DID line.
DID service provides the necessary dialed digits to ring a telephone extension directly
through a PBX, without requiring attendant intervention. DPT and FXO functions are
also used with Automatic Call Distributor (ACD), voice mail, and Computer
Telephony Integration (CTI) applications.
A unique range of software-controlled signaling capabilities connects virtually any
type of 2-wire battery-sink telephone line service. Supported features include caller ID,
calling party disconnect, distinctive ringing, ground start, and E&M signaling
conversion. Automatic impedance balancing provides echo-free service connections
across a wide range of customer equipment and line conditions. V.90 transmission
ensures optimal dial-up modem performance.
As a component of the Axxius 800 platform, the FX0 Service card as several local and
remote management options available through the Axxius 800 Controller. The card can
be locally configured and managed using the Command Line Interface (CLI). Frontpanel LEDs indicate call progress and channel status. Remote management is
accomplished using the graphical configuration, management and maintenance
interfaces available in future releases of the NetworkValet (EMS).
8-2
Axxius 800 - Release 2.2
FXO Voice Card
Features
Features
l Delivers FXO or DID telephone services from T1 access circuits
l Supports CLASS services including caller ID, calling party disconnect and
distinctive ringing
l Provides up to 64 FXO or DPT voice lines in one Axxius 800 chassis, occupying
just two rack units of equipment space (19 or 23- inch rack)
l Complies with NEBS Level 3 standards for loop range and ringing protection for
end office and customer premises
l Offers fuseless overvoltage and overcurrent protection to minimize service calls
from lightning and power cross incidents
Technical Specifications
Controller Software and Hardware Required
l Release 1.1 or higher is required for the FXO Service card
l -48V NI48V Power Supply (P/N 740-0084) is required for this card
FXO Transmission Performance
l Return Loss: ERL > 26 dB, SRL > 18 dB with respect to 900Ω
+ 2.16µF
l Transhybrid Loss: ERL > 26 dB, SRL > 18 dB with respect to 900Ω + 2.16µF
l Idle Noise: A/D < 16 dBrnC0, D/A, 12 dBrnC0
l Crosstalk Coupling: < 70 dB at 0 dBrn0
l Signal/Distortion: > 35 dB with 1004 Hz, 0 dBm0 input
l Overload: +3.0 dBm/900Ω
l Frequency Response: +0.3 dB -1.0 dB from 300 to 3400 Hz
l Encoding: µ-law 255 for U.S. and Canada as defined in CCITT G.711 and G.712
l Terminating Impedance: 900Ω + 2.16µF
l Transmit Gain/Loss: +7 to -9 dB, CLI selectable
l Receive Gain/Loss: +7 to -9 dB, CLI selectable
l Modem Support: Full compatibility with V.90 modems
Axxius 800 - Release 2.2
8-3
FXO Voice Card
Technical Specifications
FXO Signaling Performance
l DC Loop Range: > 1600Ω loop or ground start
l Ringer Equivalency Number (REN): 0.4B (AC)
l Ringing Voltage Detection: detects Class A ringing follows distinctive ringing
l FXO DC Resistance: 100Ω
l Maximum DC: 150 mA
l Overvoltage: UL 1950, FCC Part 68 lightning protection
l Overcurrent: 600 V rms, 60 Amps
l Protection: solid-state (fuseless) overvoltage and over current protection
l Termination Type: FXO loop start or ground start, switch selectable per card or
via management interface per channel
l Signaling Selection: DPT functionality enabled/disabled on all 8 channels
l Address Signaling: DTMF or dial pulse
l Calling Party Disconnect: detects and forwards current interruption to disconnect
answering devices and modems
Environment
In addition to the systems environment requirements, the following applies to the FXO
card. For additional information see Installation Environment on page 2-3.
l Operating temperature range: 32° to 104° F (0° to 40° C)
Physical
l Connections made on wire-wrap pins on rear panel
l Dimensions: 3.5 in. (H) x 0.75 in. (W) x 11.25 in. (D)
8.9 cm (H) x 1.9 cm (W) x 28.6 cm (D)
l Weight: 9.1 oz. (0.26 kg)
8-4
Axxius 800 - Release 2.2
FXO Voice Card
Card Configuration
Card Configuration
The FXO voice card can be configured, to support either FXO loop start or FXO ground
start signaling, with various transmit and receive attenuation options.
CLI Commands
The following commands are used to configure the FXO card. For detailed information
on these commands, see Chapter 5, CLI Commands.
l
l
l
l
l
l
connect
Creates two-way connections between channels
disconnect
Removes a connection created by the connect command
set (fxo)
To setup the voice channels parameters (rx gain, signal, tx gain)
show (fxo)
Displays the settings (type, signaling, RxGain, TxGain) for the FXO
status (ds0)
Displays the status (AB bits received, AB bits transmitted, signal, trunk
processing) of the DS0s (AB Bit Monitoring)
status (fxo)
Displays the status (AB bits received, AB bits transmitted, signal, T1
activity, trunk processing) of the specified FXO (AB Bit Monitoring)
Axxius 800 - Release 2.2
8-5
FXO Voice Card
DIP Switch Settings
DIP Switch Settings
The FXO card DIP switches are not functional on the Axxius 800 platform.
LEDs
Each FXO port on a card has its own LED, described in the table below.
8-6
State
Loop Start
Meaning
Ground Start
Meaning
Dial Pulse Termination
Meaning
Off
N/A
Idle (tip open)
Idle (loop open)
Green
Idle
Tip ground
(incoming seizure)
Incoming seizure
Red
N/A
Ring ground
(outgoing seizure)
Loop closure (outgoing
seizure)
Yellow
Call in progress
Call in progress
Call in progress (reverse
battery)
Flashing
green
Ringing
Ringing
N/A
Axxius 800 - Release 2.2
FXO Voice Card
Channel Associated Signaling (CAS) Conversions
Channel Associated Signaling (CAS)
Conversions
Cross-connects are done at a DS0 level. The following rules need to be kept in mind
while performing cross-connects for a FXO voice card.
FXO Card DS0 Signaling
GS
DPT
T1 DS0 Signaling Type
LS
LS (loop start)
Valid
Invalid
Invalid
Valid
GS (ground start)
Invalid
Valid
Invalid
Invalid
EMDW (E&M delayed wink start)
Invalid
Invalid
Invalid
Invalid
EMI (E&M immediate start)
Invalid
Invalid
Valid
Invalid
EMICPD (E&M Immediate Start with Calling
Party Disconnect)
Invalid
Invalid
Invalid
Invalid
EMW (E&M wink start)
Invalid
Invalid
Invalid
Invalid
LS = Loop Start
GS = Ground Start
Axxius 800 - Release 2.2
LSCPD
DPT = dial Pulse Termination
LSCPD = Loop Start Calling Party Disconnect
8-7
FXO Voice Card
Channel Associated Signaling (CAS) Conversions
8-8
Axxius 800 - Release 2.2
CHAPTER
ISDN BRI Card
In this Chapter
n
Overview
n
Features
n
Technical Specifications
n
Card Configuration
-
CLI Commands
n
LEDs
n
Connector Pinouts
-
Wire-Wrap Pinout 2 Wire Services
ISDN BRI Card
Overview
Overview
The ISDN BRI Service Cards enable service providers and enterprises to deploy highdensity, standards-based, ISDN Basic Rate Interface (BRI) services over one or more
T1 or DSL access lines using TDM or ATM transport. ISDN voice, data, and real-time
video applications may be cost effectively deployed as part of any integrated
broadband service delivery.
ISDN BRI
BRI provides an end-to-end digital connection for customers with voice, data and video
needs. BRI has 2 Bearer (B) channels at 64 Kbps for voice or data and 1 Data or Delta
(D) channel at 16 Kbps for signal and control. With some ISDN BRI devices, the two
B-channels can be aggregated together for 128 Kbps capacity.
3-DS0 BRITE Mode
The ISDN BRI Card supports the 3-DS0 BRITE mode of operation. In this mode, three
DS0 channels support a BRI channel, providing eight BRI per T1. The BRI channel
consists of two B and a D channel (2B+D) which is also transported in a full DS0. The
D-channel supports the Embedded Operations Channel (EOC) and is used to pass
signaling and other management information, such as loopback commands.
The following is an example of how a Axxius 800 with a ISDN BRI card can function
as a Line Unit Network Termination (LUNT) with central office applications, and a
Line Unit Line Termination (LULT) with subscriber lines.
LUNT
Mode
BRI
Groom
DS1s
Drop
DS1s
Axxius 800
Switch
ISDN
U-BRITE
Interface
LULT
Mode
BRI
NT1
Axxius 800
Access
Navigator
ISDN BRI Service Using 3DS0 Mode
9-2
Axxius 800 - Release 2.2
ISDN BRI Card
Features
Features
l Enables carriers to economically bundle ISDN with all other services at 64 Kbps
l
l
l
l
or 128 Kbps over T1 access lines
Configurable as either Line Unit Line Terminal (LULT) for interfacing to ISDN
switch interfaces at the central office, or Line Unit Network Terminal (LUNT)
for customer premises deployment
Provides direct NTU service demarcation for ISDN video conferencing, 128
Kbps dial-up Internet, point-of-sale terminals, and ISDN Centrex or telephone
applications
Enables high service density with up to 56 ISDN BRI lines from 7 T1 lines in a
single Axxius 800 chassis, occupying two RU of equipment space (19-inch rack)
Offers solid-state fuseless protection for central office NEBS compliance and
customer premises FCC and UL safety requirements
Technical Specifications
Controller Software Required
l Release 1.1 or higher is required for the ISDN BRI service card
Product Includes
l Works with all standard Carrier Serving Area (CSA) loops - maximum 18,000 ft.
l
l
l
l
l
l
l
l
range (#26 AWG copper)
Supports standard Telcordia 3-DS0 mode
Line coding: 2B1Q
Line Rate: 160 Kbps (80 kbaud)
Front-panel multi-function LEDs provide out-of-Service, LOS/Self-test fail,
ES/SES detected, Sync, Loopback, and Normal indications
Interoperable with other standards-based ISDN BRI equipment
B1, B2, and 2B+D payload loopbacks supported
Maximum bridged tap length is 2.5 kft. (762 m)
Rear-accessed U-interface connections
Axxius 800 - Release 2.2
9-3
ISDN BRI Card
Technical Specifications
Management
l Standard ISDN SNMP MIB supported
Network Interface
l 3 DS0 mode: Uses 3 contiguous DS0 channels per ISDN BRI channel on T1
Network Standards
l Telcordia TR-NWT-000397 (1993)
l Telcordia TR-TSY-000821 (1991)
l Telcordia TR-TSY-000829 (1989)
l ANSI T1.601.1992
l ITU-T Q.920, Q.921
Clocking
l Loop timing derived from Channel 1 of ISDN BRI card or any Axxius 800 T1
line
Testing & Diagnostics
l Initiates 2B+D, B1, or B2 loopbacks toward the BRI at the NT1
l Performs self test at power up
l 3 DS0 mode: supports external loopback testing via EOC messages from the
switch
Product Supports
l TR-821 alarms
l TR-397/TR-829/TR-821 Generic Segmented Performance Monitoring
l TR-829 multi-EOC messages in 3 DS0 mode
l Metallic DC test signature in Line Unit Network Terminal (LUNT) mode
9-4
Axxius 800 - Release 2.2
ISDN BRI Card
Technical Specifications
Power
l Maximum power input: 6 W (8 port)
l Solid-state fuseless protection
Environment
In addition to the systems environment requirements, the following applies to the ISDN
BRI card. For additional information see Installation Environment, on page 2-3.
l Operating temperature range: 32° to 104° F (0° to 40° C)
Physical
l Dimensions: 3.5 in. (H) x 0.75 in. (W) x 11.25 in. (D)
8.9 cm (H) x 1.9 cm (W) x 28.6 cm (D)
l Weight: 6.9 oz. (0.20 kg)
Axxius 800 - Release 2.2
9-5
ISDN BRI Card
Card Configuration
Card Configuration
BRI card options are set with the Command Line Interface (CLI). For additional
information on these commands, see Chapter 5, CLI Commands.
CLI Commands
l
l
l
l
l
l
l
l
l
l
l
l
l
9-6
connect
Creates two-way connections between channels
disconnect
Removes a connection created by the connect command
set (bri)
Setup of ISDN ports (up/down, threshold, call reference value)
set (bri) mode
Set up ISDN cards mode of operation (3-DS0 or 4:1)
set (bri) pmsync
Set up the BRI card source for performance monitoring synchronization
set (ds0)
For cross-connect to ISDN, must be data type
status (ds1)
Displays line status or performance statistics of a specific DS1
set clock
Set the primary and secondary (clock1/clock2) master transmit clock source
show (bri)
Displays BRI port configuration
show clock
Displays actual clock source
show (ds1)
Displays DS1 configuration
status (bri)
Displays port status or performance statistics for the specified BRI
status clock
Displays actual clock status and source
Axxius 800 - Release 2.2
ISDN BRI Card
LEDs
LEDs
There is an LED for each ISDN BRI on a card. The function for each LED is listed
below:
State
Description
Off
Line U-interface is attempting synchronization, or BRI is
out of service.
Red
Line alarm (LOS or self test failure)
Yellow
ES or SES has occurred.
Flashing yellow
Line U-interface is synchronized with customer equipment,
but is not passing customer data.
Flashing green
Line U-interface is in external loopback toward the switch at
the unit.
Green
Normal (Line U-interface is active and transparently passing
customer data.)
Axxius 800 - Release 2.2
9-7
ISDN BRI Card
Connector Pinouts
Connector Pinouts
Wire-Wrap Pinout 2 Wire Services
The following pinout applies to the wire-wrap pinout for the slot of the ISDN BRI card.
9-8
Wire-Wrap Pins
Description
T1
Channel 1 Transmit Tip
R1
Channel 1 Transmit Ring
T2
Channel 2 Transmit Tip
R2
Channel 2 Transmit Ring
T3
Channel 3 Transmit Tip
R3
Channel 3 Transmit Ring
T4
Channel 4 Transmit Tip
R4
Channel 4 Transmit Ring
T5
Channel 5 Transmit Tip
R5
Channel 5 Transmit Ring
T6
Channel 6 Transmit Tip
R6
Channel 6 Transmit Ring
T7
Channel 7 Transmit Tip
R7
Channel 7 Transmit Ring
T8
Channel 8 Transmit Tip
R8
Channel 8 Transmit Ring
Axxius 800 - Release 2.2
CHAPTER
OCU-DP Card
In this Chapter
n
Overview
n
Features
n
Technical Specifications
n
Card Configuration
-
CLI Commands
Basic Setup
n
LEDs
n
Jumper Settings
n
Alarms
n
Line Rates/Line Lengths
n
Connector Pinouts
-
DDS RJ-48S
Wire-Wrap Pinout 4 Wire Services
OCU-DP Card
Overview
Overview
The Single Port and Quad Port all-rate OCU-DP Service Cards provide electrical and
physical termination of the 4-wire Digital Data Service (DDS) that is traditionally used
to interconnect lower-speed serial synchronous Data Terminal Equipment (DTE)
devices such as routers, Frame Relay Access Devices (FRAD), or video conferencing
equipment. Now DDS can be integrated with DS0 voice, fractional T1 data, ISDN, and
IP services – over multiple T1s or DS3s. This enables service providers to deliver
transport for legacy enterprise data networking or Common Channel Signaling (CCS)
circuits commonly used in Signaling System 7 (SS7) telephone networks using one
card for all standard DDS types. Plus, it can be used as a replacement for low-density,
unmanaged D4 channel banks.
The OCU-DP Service Cards provide scalable, independently configurable,
synchronous data service rates from 2.4 Kbps to 64 Kbps, including Switched 56 Kbps
data rates. Up to eight OCU-DP cards can be inserted into any of the service card slots
of the Axxius 800, providing up to 32 DDS connections. These cards enable industryleading density and cost per port at Central Offices (COs) hub and collocations
(COLOs) and cell sites.
For example, the Axxius 800 OCU-DP ports can be groomed and mapped into any of
the DS1 or DS3 ports of the Controller. The Axxius 800's (3/1/0) digital cross-connect
functionality offers DS0 service grooming, T1 drop-and-insert, and voice access
integration not available in traditional multiplexers.
The OCU-DP Service Cards have several local and remote management options
available through the Axxius 800 Controllers. Cards can be locally configured and
managed using the Command Line Interface (CLI). Remote management is
accomplished directly over either an in-band DS0 management channel or a separate
SNMP network connection, alternatively, remote management can be achieved
through the Access Navigator® over the Facility Data Link (FDL) or an in-band
dedicated DS0. Remote management will be further simplified using the graphical
configuration, and management and maintenance interfaces available in future releases
of the NetworkValet™ Enhanced Management System (EMS).
10-2
Axxius 800 - Release 2.2
OCU-DP Card
Overview
Customer Premise Application
Local Loop: 4-wire DDS
Bipolar AMI, RZ
Four RJ-48S 4-wire
keyed jacks
T1
Secondary
Primary
PSTN
-45 dB maximum loop loss, all rates
RS-232
ADIT800
600
Axxius
or V.35
2.4 - 72 KBPS
DSU/CSU
Line Rates
Primary Channel / Primary and Secondary
Only
OCU DP
DS0A data channel format
Channel
64 KBPS / 72 KBPS
56 KBPS / 72 KBPS
38.4 KBPS / 51.2 KBPS
19.2 KBPS / 25.6 KBPS
9.6 KBPS / 12.8 KBPS
4.8 KBPS / 6.4 KBPS
2.4 KBPS / 3.2 KBPS
CAC Confidential
In this model, the carrier deploys the Axxius 800 in conjunction with DDS DSU/CSUs
to provide standards-based DDS access for customer data terminal needs. In essence,
the Axxius 800 integrates the DDS capabilities that were traditionally served by D4 or
DLC Remote Terminal equipment into a customer premise multi-service solution.
Axxius 800 - Release 2.2
10-3
OCU-DP Card
Overview
SS7 Backhaul Application
Axxius 800
In this application, the carrier uses the OCU to transfer signaling and call information
between MSCs.
10-4
Axxius 800 - Release 2.2
OCU-DP Card
Features
Features
l Provides available baseband data rates from 2.4 to 72 Kbps
l Supports primary and secondary channel services, 64K clear channel service, and
l
l
l
l
l
l
l
4-wire Switched-56 service
Complies with AT&T Pub. 62310
Offers Bipolar Violation (BPV), Loss of Frame (LOF-DDSII), Loss of Signal
(LOS) and Out-of-Service (OOS) performance counters: 15 minute, 1 hour and
24 hour intervals available
Offers BPV, OOS, LOF and LOS selectable alarm thresholds
Supplies built-in self-tests including data path and RAM test status and TDM and
CSU failures
Supports DDS network control codes for OCU, CSU and DSU latching and nonlatching service loopbacks
Supports system timing from any T1 line and provides it to the connected DTE
Deploys up to 32 OCU-DP service ports in a single Axxius 800 chassis
Technical Specifications
Controller Software and Hardware Required
l Release 1.1 or higher is required for the OCU-DP service card
l -48V NI48V Power Supply (P/N 740-0084) is required for this card
Service Interface
l Single-port OCU-DP interface
-
One RJ-48S front-panel jack
Wire-wrap pins for rear-panel connection
l Quad-port OCU-DP interface
-
Four RJ-48S front-panel jack
Wire-wrap pins for rear-panel connection
Axxius 800 - Release 2.2
10-5
OCU-DP Card
Technical Specifications
Network Interface
l Each OCU port DS0 cross-connected to T1 port
Loopbacks
OCU, CSU and DSU:
l Manual loopbacks activate via CLI
l Non-latching loopbacks activate via network code
l Latching loopbacks activate via network code
Clocking
l Loop-timed from any T1 in the platform
l Sources clock to the DTE device
Power Consumption
l 6 W maximum, Quad-Port OCU-DP card
l 3 W maximum, Single-Port OCU-DP card
Environment
In addition to the systems environment requirements, the following applies to the
OCU-DP card. For additional information see Installation Environment on page 2-3.
l Operating temperature range: 32° to 104° F (0° to 40° C)
Physical
l Dimensions: 3.5 in. (H) x 0.75 in. (W) x 11.25 in. (D)
8.9 cm (H) x 1.9 cm (W) x 28.6 cm (D)
l Weight: 5.7 oz. (0.16 kg)
10-6
Axxius 800 - Release 2.2
OCU-DP Card
Card Configuration
Card Configuration
OCU-DP card options are set with the Command Line Interface (CLI). For additional
information on these commands, see Chapter 5, CLI Commands.
CLI Commands
Configuration Commands
l
l
l
l
l
set lsbackup
Set up OCU-DP port baud rate
set (ocudp) loopdetect
Set OCU-DP non-latching/latching loopback code detection
set (ocudp) mvec
Set Majority Vote Error Correction (MVEC)
set (ocudp) secondary
Set up the secondary channel service
set (ocudp) up/down
Set the OCU-DP line In or Out-of-Service.
Test Commands
l
l
set (ocudp) loopback
Set the manual loopback tests
set (ocudp) selftest
Start the OCU-DP self test
OCU-DP Status Commands
l
l
l
clear (ocudp) performance
Clear OCU-DP status counters
show (ocudp)
Displays OCU-DP card configuration (baud, loopdetect, error correction,
switched and enhanced switched service and secondary channel
provisioning)
status (ocudp)
Displays the status or performance statistics of the OCU-DP card (OOS,
LOF, LOS and BPV seconds)
Axxius 800 - Release 2.2
10-7
OCU-DP Card
Card Configuration
Basic Setup
10-8
Command
Description
set {ocudp-addr} baud
{2400|4800|9600|19200|38400|
56000*|64000}
Set the OCU-DP Baud rate.
Where ocudp-addr = {slot:port} of the
OCU-DP card to apply settings to.
set {ocudp-addr} up
Set the OCU-DP port 1 up.
show {ocudp_card-addr}
Show the OCU-DP card settings.
Where ocudp_card-addr = {slot} of the
OCU-DP card.
disconnect a
Disconnects all connections to slot a
(controller)
set {ds0-addr} type data
Sets a DS0 data signaling type
connect {ds0-addr}
{ocudp-addr}
Connects DS0 (in previous step) to OCU-DP
port (in previous step).
show connect
(ocudp_card-addr}
Displays connect information for OCU-DP
card.
Axxius 800 - Release 2.2
OCU-DP Card
LEDs
LEDs
There are two LEDs for each channel on the OCU-DP card. The function for each LED
is listed below:
State
Description
Yellow Flickering
ALL
Boot Software in control.
Green (walking down)
Red (walking up)
ALL
Application Software in control
(repeated 3.5 times).
Red, slow flash
ALL
In Boot. Application flash code checksums
did not match and Boot is waiting for
application download.
Red
ALL
In Application code waiting for Controller to
issue SW/HW revision request. This is the
first request that comes from the OCU-DP
card manager in the Controller.
Green
Yellow
Top
Bottom
Port in Self-test. Duration is 5-8 seconds.
Off
Top
Bottom
Port is set down (Out-Of-Service).
Green
Top
Port is receiving valid signals.
Red
Top
Port is receiving no signal (primary) or no
frame sync (secondary or clear channel).
Red Flashing
Bottom
Port is receiving bipolar violations
Yellow
Bottom
Port is in loopback.
Axxius 800 - Release 2.2
10-9
OCU-DP Card
Jumper Settings
Jumper Settings
The P1 and P2 Jumpers are defaulted to RJ-48S, which are the set of pins nearest the
bottom of the service card. With the jumper in this position the signals are routed to the
RJ-48S connector(s) on the face of the card. To route the signals to the 25-pin Telco
connector at the rear of the unit, move the jumpers to the backplane position, which is
the set of pins toward the top of the service card.
P1 applies to connectors 1 and 2 (connector 2 only with the 4 port card).
P2 applies to connectors 3 and 4 (for the four port card only).
Top of Card
Front of
Card
10-10
P1 is set to
RJ-48S Position
P2 is set to
25-Pin Telco
Position
Axxius 800 - Release 2.2
OCU-DP Card
Alarms
Alarms
The OCU-DP cards and supporting Controller Software will support the following
alarms:
Alarm/
Event
Severity
Category
Description
Card
Detect
Information
Equipment
OCU-DP card inserted
Card
Removed
Information
Equipment
OCU-DP card removed
Out of
Service
(OOS)
Major
Facility
Network sending Out-ofService code (OOS) or
card has LOS.
Correct with Network or
replace or deprovision the
card.
Los of
Signal
(LOS)
Major
Facility
No signal at customer link.
Correct with Customer
data path, replace the card,
or reconnect the drop.
Los of
Frame
(LOF)
Major
Facility
Framing patter not
detected at customer link.
Correct with Customer
data path, replace the card,
or reconnect the drop.
Bipolar
Violation
(BPV)
Minor
Facility
Excessive violations on
customer interface.
Correct with the incoming
signal, or deprovision card.
Axxius 800 - Release 2.2
Clear Mechanism
(alarms only)
10-11
OCU-DP Card
Line Rates/Line Lengths
Line Rates/Line Lengths
All lengths were measured to meet a BER of 10-7 with up to 45 dB of cable attenuation
at the Nyquist frequency for 56, 64 and 72 Kbps, and 40 dB all other rates.
Service Data
Rate
Primary Channel /
Secondary Channel
Max. Loop Distance (24 AWG)
Primary Channel only/Primary &
Secondary Channel
2.4 Kbps
2.4 Kbps/3.2 Kbps
13.8 miles/12.7 miles
(22.3 km/20.4 km)
4.8 Kbps
4.8 Kbps/6.4 Kbps
11.0 miles/10.0 miles
(17.7 km/16.1 km)
9.6 Kbps
9.6 Kbps/12.8 Kbps
8.0 miles/13.3 miles
(13.0 km/12.2 km)
19.2 Kbps
19.2 Kbps/25.6 Kbps
6.3 miles/5.9 miles
(10.1 km/9.4 km)
38.4 Kbps
38.4 Kbps/51.2 Kbps
5.5 miles/5.3 miles
(8.8 km/8.5 km)
56 Kbps
56 Kbps/72 Kbps
5.1 miles/4.7 miles
(8.2 km/7.6 km)
64 Kbps
64 Kbps
4.7 miles
(7.6 km)
10-12
Axxius 800 - Release 2.2
OCU-DP Card
Connector Pinouts
Connector Pinouts
The OCU-DP is part of the network, it connect to customer equipment.
DDS RJ-48S
The pinout for RJ-48S female is as follows:
1
8
Pin
Function
Description
1
Receives Data (R-1)
From Customer to Network Interface
2
Receives Data (T-1)
From Customer to Network Interface
3-6
Not Used
7
Transmits Data (T)
From Network Interface to Customer
8
Transmits Data (R)
From Network Interface to Customer
Note: The above listed functions are relative to this port.
Axxius 800 - Release 2.2
10-13
OCU-DP Card
Connector Pinouts
Wire-Wrap Pinout 4 Wire Services
The following pinout applies to the wire-wrap pinout for the slot of the OCU-DP card.
Wire-Wrap Pins
T1
Name
Description
1RX
Port 1
Receive Ring
Receive from DS1 network
Receive Tip
Receive from DS1 network
Transmit Ring
To DS1 network
Transmit Tip
To DS1 network
Receive Ring
Receive from DS1 network
Receive Tip
Receive from DS1 network
Transmit Ring
To DS1 network
Transmit Tip
To DS1 network
Receive Ring
Receive from DS1 network
Receive Tip
Receive from DS1 network
Transmit Ring
To DS1 network
Transmit Tip
To DS1 network
Receive Ring
Receive from DS1 network
Receive Tip
Receive from DS1 network
Transmit Ring
To DS1 network
Transmit Tip
To DS1 network
1TX
2RX
Port 2
2TX
3RX
Port 3
3TX
4RX
4TX
10-14
Port 4
Axxius 800 - Release 2.2
CHAPTER
Single Channel POTS Cards
In this Chapter
n
Overview
n
Features
n
Technical Specifications
n
Card Configuration
-
CLI Commands
n
Connector Pinouts
n
LEDs
n
Basic Configuration
Single Channel POTS Cards
Overview
Overview
A Single Channel POTS card provides wireless service
providers a standard FXS voice circuit for
communications, with the operations support group
under conditions where the cell site radios are being
serviced. The Single Channel POTS card features a
single RJ-11 telecom connection, and is available with
or without an integrated V.34 modem for remote
management of the Axxius platform over a dial-in
connection. These cards can be inserted into any service
card slot of the Axxius 800.
The integrated dial-in V.34 modem port connects the
remote technician to the Axxius DS3 or T1 Controller
card for remote CLI configuration. Additional local or
remotely management options are available for the
Service card as a component of the Axxius 800
platform. The card can be configured using CLI or via
or NetworkValet graphical interface.
Features
l Provides a lifeline order wire connection for
communications from the remote cell sites during
radio maintenance
l Offers solid-state overvoltage and fuseless
overcurrent protection from lightning and power
cross incidents
11-2
Axxius 800 - Release 2.2
Single Channel POTS Cards
Technical Specifications
Technical Specifications
Controller Software Required
l Release 1.0 or higher is required for the POTS Service cards
FXS Transmission Performance
l Return Loss: ERL > 28 dB, SRL > 20 dB with respect to 900Ω
+ 2.16µF
l Transhybrid Loss: ERL > 28 dB, SRL > 20 dB with respect to 900Ω + 2.16µF
l Idle Noise: A/D < 25 dBrnC0
l Signal/Distortion: > 45 dB with 1004 Hz, 0 dBm0 input
l Terminating Impedance: 900Ω + 2.16µF
l Transmit Gain/Loss: +4 to -12 dB (in .25 increments)
l Receive Gain/Loss: +4 to -12 dB (in .25 increments)
l Overload: +3.0 dBm0
l Frequency Response: +0 dB -1.0 dB from 300 to 3400 Hz
l Longitudinal Balance: >50 dB
l Modem support: full compatibility with V.90 modems
Modem Performance
l The Single Channel POTS card modem is registered for direct connection to the
PSTN
FXS Signaling Performance
l DC Loop Range: 512 Ω
l Loop Feed: Nominal -48 VDC with 26mA current limit
l Ringing Voltage: 40 V rms, 20 Hz
l Maximum Ringers: 2 REN, FCC Class B ringers
l FXS Signaling: FXS loop start
Axxius 800 - Release 2.2
11-3
Single Channel POTS Cards
Technical Specifications
Physical
l POTS connections are through front panel RJ-11
l Dimensions: 3.5 in. (H) x 0.75 in. (W) x 11.25 in. (D)
8.9 cm (H) x 1.9 cm (W) x 28.6 cm (D)
l Weight: Single Channel POTS - 5.1 oz. (0.14 kg)
Single Channel POTS w/Modem - 6.0 oz. (0.17 kg)
Environment
In addition to the systems environment requirements, the following applies to the
Single Channel POTS card. For additional information see Installation Environment on
page 2-3.
Single Channel POTS card with Modem
Note: this card is not hardened.
l
Operating temperature range: 32° to 149° F (0° to 65° C)
Single Channel POTS card
l Operating temperature range: -40° to 149° F (-40° to 65° C)
11-4
Axxius 800 - Release 2.2
Single Channel POTS Cards
Built-In Card Handles
Built-In Card Handles
The Single Channel POTS cards are designed with a handle built into the faceplate to
assist in the removal of the card from the chassis. This handle slides out away from the
unit, creating a handle for a more effective grip.
Card Configuration
The Single Channel POTS card can be configured, using CLI commands.
CLI Commands
The following commands are used to configure the POTS cards. For detailed
information on these commands, see Chapter 5, CLI Commands.
l
l
l
l
l
connect
Creates two-way connections between channels
disconnect
Removes a connection created by the connect command
set (fxsPS or fxsPSM)
To setup the voice channels parameters (rx gain, signal, tx gain).
show (fxsPS or fxsPSM)
Displays the settings (type, signaling, rx gain, tx gain) for the FXS PS cards.
status (fxsPS or fxsPSM)
Displays the status (AB bits received, AB bits transmitted, signal, T1
activity, trunk processing) of the specified FXS PS cards.
Axxius 800 - Release 2.2
11-5
Single Channel POTS Cards
Connector Pinouts
Connector Pinouts
RJ-11 Connector
There is one RJ-11 (female) connector on the front of the POTS card and two RJ-11
connectors on the POTS card with modem.
1
6
The pinouts are as follows:
11-6
Pin
Name
Description
1
n/c
Not connected
2
n/c
Not connected
3
R
Ring
4
T
Tip
5
n/c
Not connected
6
n/c
Not connected
Axxius 800 - Release 2.2
Single Channel POTS Cards
LEDs
LEDs
The POTs channel LED (left) status is described in the table below.
State
Loop Start Meaning
Off
Calling Party Disconnect
Green
Idle
Red
N/A
Yellow
Call in progress
Flashing green
Ringing
The second LED (right) is a status LED for the MODEM.
Axxius 800 - Release 2.2
State
Description
Off
Calling Party Disconnect
Green
Ringing
Yellow
Carrier Detect
11-7
Single Channel POTS Cards
Basic Configuration
Basic Configuration
WARNING! DO NOT INSTALL TWO SINGLE CHANNEL POTS SERVICE CARDS
WITH MODEM IN A AXXIUS CHASSIS. IF YOU DO, THE SYSTEM WILL HANG. TO
RESOLVE, YOU MUST REMOVE BOTH CARDS AND PLUG ONLY ONE BACK IN.
Set Up the Single Channel POTS Line
Use the following commands to set up an analog port.
Command
Description
set a:1:1 type voice
Set the DSO to voice. See set (ds0) for details.
connect a:1:1 8:1
Connect the DSO A:1:1 to port 1 of the Single
Channel POTS card in slot 8. See the set (fxsPS or
fxsPSM) command for details.
Assign this DS0 a phone line
Connect phone
Test phone for dial-tone
Set Up the Single Channel POTS Modem
Use the following commands to set up an analog port.
Command
Description
Connect a phone line to
the Modem port
11-8
>atdt3032180000
Via HyperTerm call the line
(phone number)
MODEM>
Once a modem connection is made, the screen
will reflect this.
Axxius 800 - Release 2.2
CHAPTER
Power Supply
In this Chapter
n
Overview
n
Features
n
Technical Specifications
n
Input Power
n
LEDs
n
Installing/Replacing a Power Supply
Power Supply
Overview
Overview
The Axxius 800 Power Supply options operate from either 24 VDC or 48 VDC to
supply 5V power to the Axxius platform. A single Power Supply is capable of
powering the entire Axxius 800 unit. Equipping the Axxius with two Power Supplies
provides a simultaneously shared, redundant power feed to the unit. Front panel LEDs
provide easy-to-read power status and alarms. The Power Supply can remotely notify
network operations and monitoring centers of power faults through the Axxius SNMP
or NetworkValet EMS.
The 48 VDC power supply is available in two versions:
48 VDC I48 - the standard -48 VDC power supply.
48 VDC NI48 - provides non-isolated -48 volt to the backplane, to support the
FXO and OCU-DP Service cards.
Features
l Enables the Axxius 800 to be powered from 24 VDC or 48 VDC sources
l Output voltage galvanometrically isolated from input voltage; supports either
l
l
l
l
l
l
l
l
12-2
+ or - input voltage
Supports high capacity applications
Redundant sharing design for service critical applications
Active sharing circuitry ensures long life for both Power Supplies
Thermally hardened for operation from -40 to 149 ºF ambient temperatures
Input current inrush-limiting feature prevents excessive system voltage droop
and false fuse trips
Ensures service availability with LED status, monitoring, and remote alarming
capabilities
Facilitates quick and simple installation using connectorized design
Meets UL and CSA safety requirements
Axxius 800 - Release 2.2
Power Supply
Technical Specifications
Technical Specifications
Components
l 24 VDC Power Supply
l 48 VDC NI48 Power Supply
l 48 VDC I48 Power Supply
l Cable connector
Electrical Input Characteristics
Input power fully isolated from circuit and chassis ground
24 VDC
l
24 (21.0 to 30.0) VDC, +5 ADC, 120 W rated input
l
Startup at 22 V maximum
l
Low voltage shutdown at 19 V minimum
l
High voltage shutdown at 33 V minimum
l
Maximum cold start inrush current: 15 A peak at 30 VDC
48 VDC
l
48 (41.0 to 60.0) VDC, 2.5 ADC, 120 W rated input
l
Startup at 44 V maximum
l
Low voltage shutdown at 37.5 V minimum
l
High voltage shutdown at 66.0 V minimum
l
Maximum cold start inrush current: 7.5 A peak at 60 VDC
Electrical Output Characteristics
l 5 VDC, 20 A maximum
Axxius 800 - Release 2.2
12-3
Power Supply
Technical Specifications
Alarms
l Communicates status to Controller when 24 or 48 VDC input voltage is low
Interface Connectors
l Rear PCB connector: Axxius 800 backplane
Environment
In addition to the systems environment requirements, the following applies to the
Power Supplies. For additional information see Installation Environment on page 2-3.
l Operating temperature range of the Power Supplies: -40° to 149° F
(-40° to 65° C)
Physical
l Connections made on front of card using RJ-11 connector
l Dimensions: 3.5 in. (H) x 1.75 in. (W) x 11.25 in. (D)
8.9 cm (H) x 4.4 cm (W) x 28.6 cm (D)
l Weight: 1 lb. 2 oz. (0.51 kg)
12-4
Axxius 800 - Release 2.2
Power Supply
Input Power
Input Power
The following graphic displays the back of the Axxius chassis, with the Input power
for the Power Supply slot A and B noted.
Axxius 800 - Release 2.2
12-5
Power Supply
LEDs
LEDs
Both power supply cards have identical LEDs, as described in
the table below.
LED
State
Description
DC
Input
Off
DC input missing or fuse blown
Yellow
Under or over-voltage
Green
Valid DC input present
Off
No 5V output (neither power supply
operating)
Red
5V output not functioning (2nd unit
operating)
Green
5V output good
Output
Voltage
Status
12-6
Axxius 800 - Release 2.2
Power Supply
Installing/Replacing a Power Supply
Installing/Replacing a Power Supply
Power
1
Power
2
Front
Install a Power Supply
The Axxius has redundant Power Supply System capability. The unit will run on one
power supply (and not be redundant) or can have 2 power supplies installed.
1. Connect the power cord to the associated connector (Power 1 or Power 2).
See Power Connections on page 3-7 for details on the Power Connector.
Note: this step is for installation only.
2. Simply slide the Power Supply into the Power 1 or Power 2 slot following card
guides.
3. Press gently on the faceplate of the power supply to ensure that the connector
on the power supply is fully mated to its mating connector on the backplane.
4. Both front panel LEDs should illuminate green.
Remove a Power Supply
Remove power supply by grasping faceplate at top and bottom and pulling power
supply straight out of the case. If this is a redundant system, this will not effect power
to the system.
Axxius 800 - Release 2.2
12-7
Power Supply
Installing/Replacing a Power Supply
12-8
Axxius 800 - Release 2.2
CHAPTER
Quad DS1 ADPCM Card
In this Chapter
n
Overview
n
Features
n
Technical Specifications
n
Card Configuration
-
CLI Commands
Cross-Connects
Basic Setup
n
Jumper Settings
n
Connector Pinouts
n
RJ-48 Connector
LEDs
Quad DS1 ADPCM Card
Overview
Overview
The Quad DS1 ADPCM Service card is a component of the Axxius 800 Access
Integration Platform. With the ADPCM Service card, the Axxius 800 provides an
intelligent, compact device that can compress and groom voice traffic, which increases
bandwidth utilization and reduces costs. Using Adaptive Differential Pulse Code
Modulation (ADPCM), the ADPCM Service card compresses selected voice timeslots
from one of the T1 ports. Compression maps are CLI configurable for the ADPCM
port.
The ADPCM Service card is capable of packing two analog voice channels into a single
DS0 and functions simultaneously as a digital cross-connect switch for grooming,
bypassing or switching any combination of 64 kbps timeslots. It supports four T1
circuits and includes integral T1 CSU circuitry. V.35/RS-530 high-speed data ports, for
integral DSU operation, can be added to the platform with the Dual V.35 Service Card
and gives users the ability to drop and insert local data into available timeslots.
The ADPCM Service card utilizes industry-standard ADPCM voice compression
techniques to increase the voice capacity of T1 links. It offers flexible timeslot
assignments for mapping and configuration of compressed and non-compressed clear
channels to groom voice and data to meet network traffic requirements between remote
cell sites and the Mobile Switching Center (MSC). Data and digital traffic (i.e., GSM,
CDMA, and TDMA) can ride along with compressed analog voice traffic over standard
T1 circuits for supporting mixed analog and digital cellular sites.
The Axxius 800 DS1 or DS3 Controller Cards manage and control the ADPCM Service
card. The ADPCM Card is a highly integrated single-module solution that can be fully
integrated with additional service cards. Hardware investments are protected as user
networking needs change.
NOTE: There are 4 ports on the DS1 ADPCM Service card, only port 1
supports the ADPCM function.
13-2
Axxius 800 - Release 2.2
Quad DS1 ADPCM Card
Features
Features
l 32 Kbps ADPCM voice compression
l Supports Clear Channel Signaling and line formatting for 32 Kbps ADPCM
l
l
l
l
l
voice-band signals according to ANSI T1.302-1989
Grooms the voice and data mix from selectable channel control options
Supports up to 14.4 Kbps analog encoded data
4 DS1/T1 interfaces with integrated CSU, (DSX1 or DS1 port selections)
Operates end-to-end with existing transcoder equipment at the MSC
One modular integrated platform for DS3, DS1, V.35, POTS, 10/100 interfaces
Technical Specifications
Controller Software Required
l Release 2.0 or higher is required for the ADPCM service card
T1 Interface
l 4 T1 ports operating at 1.544 Mbps ±50 bps
l T1 Port 1 provides ADPCM voice compression capability
l Expansion to 36 T1 ports in a single chassis using Quad T1 or Quad DS1
l
l
l
l
l
l
l
ADPCM Service cards
SF (D4) or ESF framing, AMI or B8ZS line coding (DS1 operation)
Short-haul or long-haul loop settings for T1
4 RJ-48C front interface access (Control Panel Interface card) or rear wire-wrap
pins (selectable)
T1 Line Interface: T1-CSU or T1-DSX (field selectable)
Line Build Out (DSX-1): 655 feet
Receive Sensitive (DS1): 0 to -22 dB @ 772KHz ALBO
Output Level (DS1): Selectable at 0 to -22 dB
Axxius 800 - Release 2.2
13-3
Quad DS1 ADPCM Card
Technical Specifications
T1 Interface (continued)
l Jitter: meets AT&T Pub. TR-62411
l Solid-state fuseless overvoltage and overcurrent line protection
l Channel status LEDs
l Less than 3 ms signaling latency
l Less than 10 ms overall Axxius 800 system signaling latency
ADPCM Signaling
l Clear Channel Signaling passed on 64K clear channel
l 24-channel 32 Kbps ADPCM compression
Management
l Managed by Axxius 800 DS1 or DS3 Controller Craft or SNMP Interface
Synchronization
l Provides reference clock to backplane from selected T1
Network Standards
l RFC 2495
l ANSI T1.403-1995, T1.231-1993
l ITU G.703, G.704
l 32 Kbps ADPCM voice compression per ANSI T1.302-1989
Clocking
l Loop-timed from any T1
l External from BITS clock input (T1.101, T1.102 signal type)
l Revertive or non-revertive (provisionable) clock switching provides automatic
backup to secondary T1 should the primary T1 fail
l Operates as a Stratum 4E device as defined by Telcordia GR-1244-CORE and
AT&T TR 62411
13-4
Axxius 800 - Release 2.2
Quad DS1 ADPCM Card
Technical Specifications
Alarms
l Support standard T1.403 alarms
l LOS (Loss of Signal), Red, Yellow, Blue
l ESF Performance Error Count Threshold
l Timing Loss
l All alarms are logged in an event log
l Loss of power triggers minor alarm
l Generates SNMP traps for alarming
Testing and Diagnostics
l T1.403 payload loopbacks (ESF only)
l T1.403 remote and local line loopbacks (ESF and SF)
l T1.231 Performance History (15 minute intervals, 24 hour totals)
l T1.403 Performance Report Messages (PRMs)
Power Consumption
l Less than 4.5 W per card
Environment
For systems environment requirements, see Installation Environment on page 2-3.
Physical
l Dimensions: 3.5 in. (H) x 0.75 in. (W) x 11.25 in. (D)
8.9 cm (H) x 1.9 cm (W) x 28.6 cm (D)
l Weight: 5.1 oz. (0.14 kg)
Axxius 800 - Release 2.2
13-5
Quad DS1 ADPCM Card
Card Configuration
Card Configuration
All options on the this Service card are set using the Command Line Interface (CLI).
CLI Commands
The following commands are used to configure the Quad DS1 ADPCM card. For
detailed information on these commands, see Chapter 5, CLI Commands.
l
l
l
l
l
l
l
l
l
l
13-6
connect
Creates two-way connections between channels.
disconnect
Removes a connection created by the connect command.
set (ds1 card) adpcm map
Sets the voice compression map on the ADPCM card (none, map 1, map 2
or map 3).
set (ds1)
Sets up the DS1 interfaces (clock, up, down, fdl, framing, id string, lbo, line,
linecode, loopdetect).
set lsbackup
Defines the backup protection slot.
set lsprotect enable/disable
Enables or disables the Low Speed Protection options on the system.
set lsprotect manual
Sets the manual mode control for protected ports.
set lsprotect nonrevertive
Defines the port non-revertive status and priority level.
set lsprotect remove
Removes port from protected mode.
set lsprotect revertive
Defines the port revertive status and priority level.
Axxius 800 - Release 2.2
Quad DS1 ADPCM Card
Card Configuration
l
l
l
l
l
l
l
show (adpcm)
Displays current settings for the ADPCM card (circuit ID, up.down,
framing, line coding, line build out, loop code detection, loop back, fdl type,
ADPCM, ADPCM Map)
show connect adpcm
Displays the connections for the ADPCM port.
show (ds1)
Displays current settings for DS1
show lsprotect
Displays the low speed protection settings.
status (adpcm)
Displays the status of the ADPCM card (receive, transmit, loopback)
status (ds1)
Displays the status of the DS1 (receive, transmit, loopback)
status lsprotect
Displays the current status of the low speed protection cards.
Axxius 800 - Release 2.2
13-7
Quad DS1 ADPCM Card
Card Configuration
Basic Setup
Before configuring the DS1 ADPCM card, there are some basics that need to be
considered:
l All DS0s to be compressed reside on T1 number 1 of the ADPCM card
l ADPCM is capable of transporting any combination of 64 and 32K
l All 24 DS0s can be transported either compressed or uncompressed, but not both
at the same time.
l All DS0s to be compressed must be set to type data.
The following is a basic setup:
Command
Description
Connect T1 cable to port 1 of the ADPCM service card
13-8
set {adpcm_card-addr}
{none|map1|map2|map3}
Enable compressing by selecting Map type.
Note: none disables compression. See the
following section on Maps.
show (adpcm_card-addr}
Displays the status of the card, and the mapping.
set {2:1:1-12} type data
Set the channel (DS0) type to data on the
ADPCM channels. See set (ds0) command for
more information.
set {2:4:1-12} type data
Set the channel (DS0) type to data on the
channels for cross-connect. See set (ds0)
command for more information.
connect 2:1:1-12 2:4:1-12
Set cross-connects.
The example connects all 24 channels of the
ADPCM to the 12 channels of the T1 (now
compressed) on port 4. Example is with map2
show connect adpcm {2:1)
Displays the connections made above.
Axxius 800 - Release 2.2
Quad DS1 ADPCM Card
Card Configuration
Cross-Connects
It is important to note that all timeslots are cross-connected in pairs. The actual pairs
that can be cross-connected are dependant upon which of the 3 supported mappings are
set using the set (ds1 card) adpcm map command.
Map1
l
Channels 1-12 and 14-23 are compressed into 11 DS0s (2 to 1 compression)
l Channel 24 is used for 64K non-compressed data (mapped to channel 12)
l Channel 13 is idle (cannot be used)
l Channel pairing is as follows:
1/2, 3/4, 5/6, 7/8, 9/10, 11/12, 14/15, 16/17, 18/19, 20/21, 22/23 (mapped to
channels 1-11)
Note: 13 and 24 are not included in the pairing. See above bullets.
Map2
l
Channels 1-24 are compressed into 12 DS0s (2 to 1 compression)
l Channel pairing is as follows:
1/2, 3/4, 5/6, 7/8, 9/10, 11/12, 13/14, 15/16, 17/18, 19/20, 21/22, 23/24
(mapped to channels 1-12)
Map 3
l Channels 1-22 are compressed into 11 DS0s (2 to 1 compression)
l Channel 24 is used for 64K non-compressed data (mapped to channel 12)
l Channel 23 is idle (cannot be used)
l Channel pairing is as follows:
1/2, 3/4, 5/6, 7/8, 9/10, 11/12, 13/14, 15/16, 17/18, 19/20, 21/22 (mapped to
channels 1-11)
Note: 23 and 24 are not included in the pairing. See above bullets.
Example: connect 2:1:1 2:4:1
The above example will connect the ADPCM pair 1 (which are
actually channels 1 and 2) to channel 1 (now compressed) on port 4.
Example: connect 2:1:1-12 2:4:1-12
With Map 1, the example will connect the ADPCM pairs 1-11 (which
is actually channels 1-23 - no 12) to channels 1-11 (now compressed)
on port 4 and channel 24 (12) to channel 12 (non-compressed data).
Axxius 800 - Release 2.2
13-9
Quad DS1 ADPCM Card
Jumper Settings
Jumper Settings
The P2 and P3 Jumpers are defaulted to RJ-48, which are the set of pins nearest the
connectors. In this position the DS1 signals (TX and RX) are routed to the RJ-48
connectors on the face of the card, see RJ-48 Connector on page 13-11 for pinout
information. To route the DS1 signals to the wire-wrap connector at the rear of the unit,
move all the jumpers to the "backplane" position (the two rightmost pins for each
signal). See Slot (1-8) Wire-Wrap Connectors on page 3-12 for more information on
these connectors.
P2 and P3 Jumpers
Faceplate of ADPCM card
BACKPLANE
22
24
1
3
22
13-10
BACKPLANE
RJ48
Jumper set to
RJ-48 connector
on the front of
the card
3
RJ48
Jumper set to
Wire-Wrap
connectors on the
back of the chassis
1
1
P3
3
24
1
22
P2
3
24
24
Axxius 800 - Release 2.2
Quad DS1 ADPCM Card
Connector Pinouts
Connector Pinouts
RJ-48 Connector
There are four RJ-48 (female) connectors on the front of the Quad DS1 ADPCM Card.
1
8
The pinouts are as follows:
Pin
Name
Description
1
Receive Ring
Receive from DS1 network
2
Receive Tip
Receive from DS1 network
3
n/c
Not connected
4
Transmit Ring
To DS1 network
5
Transmit Tip
To DS1 network
6-7
n/c
Not connected
8
Chassis Ground
Axxius 800 - Release 2.2
13-11
Quad DS1 ADPCM Card
LEDs
LEDs
Each channel on the Quad DS1 ADPCM card has two LEDs. The description of the top
LED is shown below, the bottom LED is not used with this application.
13-12
State
Description
Top LED
(active)
Off
Off line
Green
Normal
Bottom LED
(not used)
Red
Loss of Signal (LOS)
Yellow
Bipolar Violation (BPV)
Flashing Green
Loopback active
Flashing Yellow
Yellow Alarm
(Remote Alarm Indication)
Flashing Red (Slow)
Loss of Frame (LOF) or Alarm
Indication Signal (AIS)
Flashing Red (Fast)
Self-test Failure
Axxius 800 - Release 2.2
CHAPTER
Quad T1 & Quad DS1/E1 Card
In this Chapter
n
Overview
n
Features
n
Technical Specifications
n
Card Configuration
- CLI Commands
n
Jumper Settings
n
Connector Pinouts
- RJ-48 Connector
n
LEDs
Quad T1 & Quad DS1/E1 Card
Overview
Overview
The Hardened Quad T1 and DS1/E1 Service cards enable wireless service providers to
cost-effectively provision and expand network bandwidth and groom available DS0s
onto other T1 tributaries for optimal T1 bandwidth utilization. The card can be inserted
into any slot of the eight-slot Axxius 800 and is software selectable for DS1 or DSX
operation. It provide full 1/0 cross-connect capability, drop-and-insert functionality
and supports fractional and full T1 services, as well as DS0 trunking. This service card
has been specifically hardened to stand up to the extreme environmental conditions
commonly associated with wireless cell site deployments.
NOTE: The E1 functionality of this card is not currently supported on the
Axxius platform.
When fully equipped with eight Quad T1 Service cards plus the four-port DS1
Controller, an Axxius 800 can support up to 36 T1 ports. This available bandwidth
enables the Axxius to cost-effectively address fixed-wireless service distribution,
mobile wireless backhaul and daisy-chained DS0 distribution to remote cell sites. The
flexible T1 Service card features four front-panel 8-pin RJ-48C shielded connectors.
The T1 Service card can be locally or remotely managed as a component of the Axxius
800 platform. The card can be configured using a Command Line Interface (CLI).
Hardened Quad DS1/E1 Service card
This card is configurable to DS1 or E1 (E1 will be supported in the future) with a single
CLI command, regardless of Controller type.
Hardened Quad T1 Service card
The Hardened Quad T1 Service card enables cost-effective provisioning and expansion
of T1 bandwidth with full non-blocking digital cross-connection of all timeslots to any
Adit service card.
14-2
Axxius 800 - Release 2.2
Quad T1 & Quad DS1/E1 Card
Features
Features
l Integrated T1 CSU functionality with FCC registration for direct connection to
l
l
l
l
l
l
l
l
l
T1 lines
B8ZS or AMI encoding and SF (D4) or ESF framing
Local, line and payload loopbacks
Framing and coding conversion between T1 ports
Flexible system clock timing, which may be derived from or provided to any T1
Up to eight Quad T1 Service cards plus the four ports from the DS1 Controller in
a single Axxius 800 for a total of 36 DS1s/CSUs per chassis
Full non-blocking Digital Cross-connection System (DCS) of all timeslots to any
Axxius Service card
ESF performance reporting
Payload and line loopback
Secondary solid-state fuseless protection to lightning and AC power cross
incidents
Axxius 800 - Release 2.2
14-3
Quad T1 & Quad DS1/E1 Card
Technical Specifications
Technical Specifications
Controller Software Required
l Release 1.0 or higher is required for the Quad T1service card
T1 Interface
l 4 T1 ports operating at 1.544 Mbps (DS1) or 2.048 Mbps (E1)
±50 bps
l Expansion to 36 T1 ports in a single chassis using Quad T1 Service cards
l SF (D4) or ESF framing, AMI or B8ZS line coding
l Short-haul or long-haul loop settings for T1
l 4 RJ-48C front interface access (Control Panel Interface card) or rear wire-wrap
l
l
l
l
l
l
l
l
l
pins (selectable)
T1 Line Interface: T1-CSU or T1-DSX (field selectable)
Line Build Out (DSX-1): 655 feet
Receive Sensitive (DS1): 0 to -22 dB @ 772KHz ALBO
Output Level (DS1): Selectable at 0 to -22 dB
Jitter: Meets AT&T Pub. TR 62411
Solid-state fuseless overvoltage and overcurrent T1 line protection
Channel status LEDs
Less than 3 ms signaling latency
Less than 10 ms overall Axxius 800 system signaling latency
Network Standards
l RFC 2495
l ANSI T1.403-1995, T1.231-1993
l AT&T TR 62411, TR 54016
l ITU G.703, G.706, G.823, I.431
l TBR 12 and 13
14-4
Axxius 800 - Release 2.2
Quad T1 & Quad DS1/E1 Card
Technical Specifications
Clocking
l Loop-timed from any T1
l External from BITS clock input (t1.101, t1.102 signal type)
l Revertive or non-revertive (provisionable clock switching provides automatic
backup to secondary T1 should the primary T1 fail
l Operates as a Stratum 4E device as defined by Telcordia GR-1244-CORE and
AT&T TR 62411
Alarms
l Support standard T1.403 alarms
l LOS (Loss of Signal), Red, Yellow, Blue
l ESF Performance Error Count Threshold
l Timing Loss
l All alarms are logged in an event log
l Loss of power triggers minor alarm
l Generates SNMP traps for alarming
Testing and Diagnostics
l T1.403 payload loopbacks (ESF only)
l T1.403 remote and local line loopbacks (ESF and SF)
l T1.231 Performance History (15 minute intervals, 24 hour totals)
l T1.403 Performance Report Messages (PRMs)
Power Consumption
l Less than 4.5 W per card
Axxius 800 - Release 2.2
14-5
Quad T1 & Quad DS1/E1 Card
Technical Specifications
Environment
In addition to the systems environment requirements, the following applies to the Quad
T1 (hardened) card. For additional information see Installation Environment on page
2-3.
l Operating temperature range of the Quad T1 card: -40° to 149° F
(-40° to 65° C)
Physical
l Dimensions: 3.5 in. (H) x 0.75 in. (W) x 11.25 in. (D)
8.9 cm (H) x 1.9 cm (W) x 28.6 cm (D)
l Weight: 5.1 oz. (0.14 kg)
14-6
Axxius 800 - Release 2.2
Quad T1 & Quad DS1/E1 Card
Card Configuration
Card Configuration
All options on the this card are set using the Command Line Interface (CLI).
CLI Commands
The following commands are used to configure the Quad T1 card. For detailed
information on these commands, see Chapter 5, CLI Commands.
l
l
l
l
l
l
l
l
l
l
l
l
l
connect
Creates two-way connections between channels.
disconnect
Removes a connection created by the connect command.
set (ds1)
Sets up the DS1 interfaces
set lsbackup
Defines the backup protection slot.
set lsprotect enable/disable
Enables or disables the Low Speed Protection options on the system.
set lsprotect manual
Sets the manual mode control for protected ports.
set lsprotect nonrevertive
Defines the port non-revertive status and priority level.
set lsprotect remove
Removes port from protected mode.
set lsprotect revertive
Defines the port revertive status and priority level.
show lsprotect
Displays the low speed protection settings.
show (ds1)
Displays current settings for DS1
status (ds1)
Displays the status of the DS1 (receive, transmit, loopback)
status lsprotect
Displays the current status of the low speed protection cards.
Axxius 800 - Release 2.2
14-7
Quad T1 & Quad DS1/E1 Card
Jumper Settings
Jumper Settings
The P2 and P3 Jumpers are defaulted to RJ-48, which are the set of pins nearest the
connectors. In this position the DS1 signals (TX and RX) are routed to the RJ-48
connectors on the face of the card, see RJ-48 Connector on page 14-9 for pinout
information. To route the DS1 signals to the wire-wrap connector at the rear of the unit,
move all the jumpers to the "backplane" position (the two rightmost pins for each
signal). See Slot (1-8) Wire-Wrap Connectors on page 3-12 for more information on
these connectors.
P2 and P3 Jumpers
Faceplate of T1 Card
BACKPLANE
22
24
1
3
22
14-8
BACKPLANE
RJ48
Jumper set to
RJ-48 connector
on the front of
the card
3
RJ48
Jumper set to
Wire-Wrap
connectors on the
back of the chassis
1
1
P3
3
24
1
22
P2
3
24
24
Axxius 800 - Release 2.2
Quad T1 & Quad DS1/E1 Card
Connector Pinouts
Connector Pinouts
RJ-48 Connector
There are four RJ-48 (female) connectors on the front of the Quad T1 and DS1/E1
Cards.
1
8
The pinouts are as follows:
Pin
Name
Description
1
Receive Ring
Receive from DS1 network
2
Receive Tip
Receive from DS1 network
3
n/c +
Not connected
4
Transmit Ring
To DS1 network
5
Transmit Tip
To DS1 network
6-7
n/c
Not connected
8
Chassis Ground
Axxius 800 - Release 2.2
14-9
Quad T1 & Quad DS1/E1 Card
LEDs
LEDs
Each channel on the card has two LEDs. The description of the top LED is shown
below, the bottom LED is not used with this application.
Top LED
(active)
Bottom LED
(not used)
14-10
State
Description
Off
Off line
Green
Normal
Red
Loss of Signal (LOS)
Yellow
Bipolar Violation (BPV)
Flashing Green
Loopback active
Flashing Yellow
Yellow Alarm
(Remote Alarm Indication)
Flashing Red (Slow)
Loss of Frame (LOF) or Alarm
Indication Signal (AIS)
Flashing Red (Fast)
Self-test Failure
Axxius 800 - Release 2.2
CHAPTER
Terminal Server Router Card
In this Chapter
n
Overview
n
Features
n
Technical Specifications
n
Card Configuration
-
CLI Commands
n
Connector Pinout
n
LEDs
Terminal Server Router Card
Overview
Overview
The Quad-Port Terminal Server Router (TSR) card combines the performance and
expand ability of a selectable four-port RS-232 and 10/100Base-TX Ethernet switch
with dedicated routing functionality in a low-cost solution to help wireless service
providers remotely manage cell site LMU and switching devices, and deliver routing
capabilities needed to offer 3G applications services. The ability to remotely manage
these cell site devices significantly reduces maintenance truck rolls costs, and enables
the wireless service provider to focus their efforts on expanding their cell site coverage
for increased revenues.
The TSR card employs a dedicated processor to ensure high performance and product
feature expansion. A powerful set of standard features includes IP and IPX routing,
Layer 2 bridging, ML-PPP, networking security and management capabilities to
integrate services in the digital last mile. The four RJ-45 ports can be configured as
either RS-232 or 10/100Base-TX Ethernet connections to support remote device
management from the Network Operations Center (NOC) or 3G routed data
applications services. The Axxius 800’s modular design supports up to eight TSR
cards.
The TSR card is SNMP or Command Line Interface (CLI) manageable. Management
connectivity is provided either by directly through the user data port connection on the
TSR card, or through the DS1 or DS3 Controller cards as a component of the Axxius
800 platform.
Quad TSR with TBOS
The Quad-Port Terminal Server Router (TSR) card with TBOS-to-SNMP conversion,
offers a fully integrated solution to convert and transport TBOS alarms. The TBOS data
received on the TSR card’s RS-232 ports are stored and made available via SNMP
GETs. Alarms from TBOS-monitored equipment are converted to SNMP traps and
transported over the WAN DS0 to the Network Operation Center's SNMP Trap
Manager. This eliminates the need for a separate TBOS alarm monitoring system for
fixed microwave backhaul systems and reduces bandwidth expense. Up to 8 TBOS
devices can be cascaded off a single TSR RS-232 port.
15-2
Axxius 800 - Release 2.2
Terminal Server Router Card
Features
Features
l Enables remote management of cell site resources
l Supplies 4 selectable RS-232 synchronous or 10/100Base-TX Ethernet
connections per card
l Supports up to 8 Router cards per Axxius 800 chassis
- Multi-point networking with up to 24 WAN connections per router
- Each WAN connection can be provisioned with multiple DS0s
- Deliver more than 2 T1s bandwidth per Router card; up to 60 DS0s per Router
card
l Ensures high performance and feature expansion
l Enables management via menu-driven or CLI Router interface
l Supports packet filtering and Spanning Tree Protocol
l Allows network address and port translation (NAT, PAT)
l Enables multiple T1 facilities to function as a single IP WAN interface using
ML-PPP for bandwidth scalability beyond a single T1
l Supports Dynamic Host Configuration Protocol (DHCP)
l Delivers 3,700 packets per second throughput (64 byte packets)
Additional Features on a TSR Card with TBOS
l Decodes the TBOS protocol to recover the individual alarm data points
l SNMP traps based upon changes to monitored alarm conditions
l Supports SNMP traps and GETs for the monitored alarm data
l Daisy chain up to 8 TBOS displays off 1 TSR RS-232 port
Axxius 800 - Release 2.2
15-3
Terminal Server Router Card
Technical Specifications
Technical Specifications
Controller Software Required
l Release 1.0 or higher is required for the TSR service card
l Release 2.0 or higher to support a TSR Service card with TBOS
l TSR release 1.2 or higher to support all features listed in this chapter
Management
l CLI driven via RS-232 or Ethernet
l Menu-driven via RS-232 or Ethernet, see the Terminal Server Router User
l
l
l
l
l
l
Manual for information on the Menu-driven software
SNMP
Ping, Trace Route
Ethernet management port
IP management DS0 bearer channel
Code download via TFTP
Configuration upload and download via TFTP
WAN Interface
l Any DS1 or DS3 interface on the Axxius 800 platform
l Up to 24 WAN interfaces per Router
l Up to 60 DS0s bandwidth per Router
l PPP, Frame Relay, PPP in Frame Relay and GRE tunneling
LAN Interface
l A single 10/100Base-TX auto-sensing port/auto-MDIX ports
l 8-pin RJ-45 modular jacks
15-4
Axxius 800 - Release 2.2
Terminal Server Router Card
Technical Specifications
RS-232 Interface
l Up to 4 RS-232 DCE ports
l Selectable asynchronous data rates and data parameters
l 8-pin RJ-45 modular jacks
l RJ-45-to-DB9 adapter cable available
Routing
l IPX RIP/SAP
l IP RIPv1, RIPv2, RIPv/RIPv2 compatibility mode
l Static routing
l Classless routing (CIDR)
Bridging
l IEEE 802.1D MAC bridging, using the Spanning Tree Algorithm and Protocol
Router Performance
l Minimum of 3,000 64-byte packets per second throughput
Advanced Capabilities
l DHCP server, BOOTP Relay
l SysLog
l Domain Name Server (DNS) proxy
l DNS resolver
l Simple Network Time Protocol (SNTP) support for timing from a separate
network server
l Secondary IP Address
l RS-232 terminal server
l RS-232 TBOS support: RS-422 TBOS support can be provided using an external
RS-232 to RS-422 converter
Axxius 800 - Release 2.2
15-5
Terminal Server Router Card
Technical Specifications
Frame Relay
l RFC 1490 encapsulation
l ANSI T1.617 Annex D LMI
l ITU Q.933 Annex A LMI
Filtering
l Filtering up to Layer 4, stateful
Security
l Three user accounts
l Three levels of security
l PAP and CHAP
l Network Address Translation (NAT)
l NAT Bypass
l Port Address Translation (PAT)
MIBs
l RFC 1212 (Concise MIB)
l RFC 2011 (IP)
l RFC 1213 (MIB II)
l RFC 2115 (Frame Relay)
l RFC 1406 (DS1/E1)
l RFC 2233 (Interface)
l RFC 1471 (LCP/PPP)
l Enterprise MIB, including
l RFC 1473 (IP/PPP)
l RFC 1643 (Ethernet)
l RFC 1659 (RS-232)
15-6
equipment-specific MIBs to
support GET operation on
TBOS-monitored equipment
Axxius 800 - Release 2.2
Terminal Server Router Card
Technical Specifications
Equipment Supported for TBOS-to-SNMP Conversion
l Proxim Lynx.sc Microwave Radio Models 31250, 31600, 31250, 31650
l Proxim Lynx.HD Microwave Radio Models 31350-10, 31850-10, 31145-10,
31145-F
l Proxim Lynx DS-3 Microwave Radio Models 27710-91, 27750-91
l Proxim Lynx Hot Standby Protection Switch Models 31455, 31420
l Alcatel MDR-4000 Microwave Digital Radio
Testing and Diagnostics
l Ping, Trace Route
l WAN monitor
Power
l Less than 5 W
Environment
In addition to the systems environment requirements, the following applies to the
Terminal Server Router card. For additional information see Installation Environment
on page 2-3.
l Operating temperature range of the TSR card: -40° to 149° F
(-40° to 65° C)
Physical
l Dimensions: 3.5 in. (H) x 0.75 in. (W) x 11.25 in. (D)
8.9 cm (H) x 1.9 cm (W) x 28.6 cm (D)
l Weight: 5.2 oz. (0.15 kg)
Axxius 800 - Release 2.2
15-7
Terminal Server Router Card
Card Configuration
Card Configuration
The Terminal Server Router card has the option of configuration through CLI or the
TSR Menu-driven software, which is accessed through Telnet. The following CLI
commands are all TSR related. For information on the TSR Menu-driven software, see
the Terminal Server Router User Manual.
NOTE: With this release TBOS features are set with the TSR Menu-driven
software. See the Terminal Server Router User Manual for more
information.
CLI Commands
Many of the router features can be configured directly with CLI commands. For
configuration of features not covered with CLI commands, the operator must use the
TSR Menu-driven software. For detailed information on the following TSR
commands, see Chapter 5, CLI Commands.
l
l
l
l
l
l
l
15-8
add (router) dhcp server option
Enable add optional DHCP server attributes every time a DHCP client
discovery is initiated.
add (router) dns proxy
Enable DNS proxy and add a remote DNS server address to the TSR card.
add (router) remote
Add a remote WAN profile to the WAN profile table.
add (router) snmp community
Add a SNMP community to an interface on the TSR card.
add (router) snmp trap
To specify a destination to send SNMP trap messages.
add (router) static dns host
Add a static DNS host record for resolving a domain name to an IP address
if the DNS server cannot provide the information.
add (router) uploaduser
To specify a host that is allowed to upload configuration/software files.
Axxius 800 - Release 2.2
Terminal Server Router Card
Card Configuration
l
l
l
l
l
l
l
l
l
l
l
l
l
l
add (router-lan) filter
Add an address filter to the table of Layer 2 filter applied specified LAN
interface.
add (router-lan) secondary ip address
Add a secondary IP address and subnet to the LAN interface.
add (router-lan) static
Add a static element on the specified LAN.
add (router-wan) firewall
Add a firewall rule to a WAN.
add (router-wan) gre network
Add a "by network" GRE tunnel to a WAN.
add (router-wan) static
Add a static IP address to the table of learned addresses on the WAN
interface. This command is typically used in bridging.
clear (router) ip address table
Flush the learned entries from the IP address table for the specific interface
from the specified TSR card.
clear (router) mac address table
Flush the learned entries from the MAC address table for the specific
interface from the specified TSR card.
connect (router-trunk) (t1)
Creates two-way connections between the router port trunk connections and
any DS0 channels of the service card or controller.
delete (router) dhcp server option
Remove optional DHCP server attributes.
delete (router) dns proxy
Remove a remote DNS server address from the specified TSR card.
delete (router) remote
Delete a remote WAN profile from the WAN profile table.
delete (router) snmp community
Delete an SNMP community entry.
delete (router) snmp trap
Delete a trap destination from the TSR card.
Axxius 800 - Release 2.2
15-9
Terminal Server Router Card
Card Configuration
l
l
l
l
l
l
l
l
l
l
l
delete (router) static dns host
Delete a static DNS host record.
delete (router) uploaduser
Remove an existing authorized uploaduser.
delete (router-lan) filter
Remove a a single filter rule from the table of Layer 2 filters applied to the
specified LAN interface.
delete (router-lan) secondary ip address
Delete a secondary IP address from the LAN interface.
delete (router-lan) static
Remove a static element from the LAN interface.
delete (router-wan) firewall
Remove a firewall rule from a WAN.
delete (router-wan) gre network
Remove a "by network" GRE tunnel to a WAN.
delete (router-wan) static
Delete a static element from the WAN interface.
disconnect {slot:port:trunk}
Removes a connection created by the connect {trunk-addr}{t1-addr}
install (slot) router
Will prepare the controller for the insertion of a new router card that will
keep its currently loaded configuration.
load tftp
Will download software via TFTP to the Controller or the TSR card.
WARNING! BEFORE LOADING A DOWN-LEVEL OF ROUTER CODE TO AN
ADIT, SAVE THE CONFIGURATION TO A FILE. CONFIGURATION MAY BE RESET TO
THE DEFAULT SETTING AND CURRENT CONFIGURATION LOST.
l
15-10
rename (router) (router-wan/lan)
Change the name of a remote WAN or local LAN profile on the TSR card.
Axxius 800 - Release 2.2
Terminal Server Router Card
Card Configuration
l
l
l
l
l
l
l
l
l
l
l
l
l
l
reset (router)
Reboot the Router. All new configuration since the last configuration will be
in-use.
set (router) default
Reset the router to its default configuration settings, and will reboot.
set (router) dhcp
Configure the DHCP functions.
set (router) dns
Set the Domain Name Server options.
set (router) enhanced security
Enable the enhanced logging security on the Router.
set (router) lmi
Specify the Local Management Interface (LMI) protocol to use for the
Router.
set (router) login auth
Define the login authentication type.
set (router) login prompt
Enable and disable the login prompt.
set (router) ntp
Set the Network Time Protocol parameters.
set (router) password
Manage password access on the router.
set (router) port
Set port characteristics on a Terminal Server Router card.
set (router) ppp auth
Configure the Point-to-Point Protocol authentication on the router card.
set (router) ppp security
Set up the local external security server that the router will use to
authenticate remote PPP devices.
set (router) proxy
Configures Router in-use basics (up, down and proxy).
Axxius 800 - Release 2.2
15-11
Terminal Server Router Card
Card Configuration
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
15-12
set (router) reboot
Set automatic reboot after an upload of code or configuration file.
set (router) rip
Specify version of RIP packets to transmit and receive.
set (router) snmp
Set the SNMP contact, location, name on the router.
set (router) stp
Set the Spanning Tree Protocol on the router (card).
set (router) syslog
Set the router to send alarm and event messages to a Syslog server.
set (router-lan) filter forward
Set the forwarding mode for Layer 2 filters on the LAN interface.
set (router-lan) gateway
Specify a default IP gateway for the specified LAN interface.
set (router-lan) ip address
Specify an IP address for the specified LAN interface.
set (router-lan) ipx network
Specify an IPX address for the specified LAN interface.
set (router-lan) phy
Specify the Ethernet PHY (physical specifications) speed and mode.
set (router-lan) rip
Specify IP RIP for the LAN interface.
set (router-lan) stp
Specify the Spanning Tree Protocol on the LAN interface.
set (router-lan) up/down
Set the LAN interface up or down.
set (router-trunk) encapsulation
Specify the encapsulation to use on the TSR interface.
set (router-trunk) multilink group
Specify a router trunk to be part of a multilink PPP group.
set (router-trunk) up/down
Set the TSR trunk up or down.
Axxius 800 - Release 2.2
Terminal Server Router Card
Card Configuration
l
l
l
l
l
l
l
l
l
l
l
l
l
l
set (router-wan) dlci
Configure the DLCI for a specified WAN interface that will be using a frame
relay encapsulated trunk.
set (router-wan) gre
Configure the Generic Routing Encapsulation tunneling for a specified
WAN interface.
set (router-wan) ip
Set the IP traffic handling on the WAN interface.
set (router-wan) ip address
Set the IP address for a WAN interface.
set (router-wan) ipx
Set the IPX traffic handling on the WAN interface.
set (router-wan) nat
Configure Network Address Translation (NAT) on a specified WAN
interface.
set (router-wan) other
Set the traffic handling of protocols other than IP or IPX on the specified
WAN interface.
set (router-wan) ppp
Configure the Point-to-Point Protocol on the specified WAN interface.
set (router-wan) rip
Set the type or RIP updates on the WAN interface.
set (router-wan) stp
Configure the trunk port for a specified WAN interface.
set (router-wan) trunk
Configure the trunk port or multilink group for a specified WAN interface.
set (router-wan) up/down
Set the specified WAN interface up or down.
show (router)
Displays the current TSR settings.
show (router) dhcp
Displays the current DHCP settings for the TSR card.
Axxius 800 - Release 2.2
15-13
Terminal Server Router Card
Card Configuration
l
l
l
l
l
l
l
l
l
l
l
l
l
l
15-14
show (router) dns
Displays the current DNS settings for the TSR card.
show (router) dns proxy
Displays the current DNS Proxy settings for the TSR card.
show (router) lmi
Displays the current Local Management Interface settings for the router
card.
show (router) login
Displays the current Local Management Interface (LMI) settings for the
router card.
show (router) login
Displays the current Local Management Interface (LMI) settings for the
router card.
show (router) ntp
Displays the current NTP settings for the router card.
show (router) port
Displays the current TSR port configuration.
show (router) ppp
Displays the current Local PPP authentication and security settings for the
router card.
show (router) rip
Displays the current RIP settings for the router card.
show (router) snmp
Displays the current SNMP settings for the router card.
show (router) stp
Displays the current Spanning Tree Protocol settings for the router card.
show (router) syslog
Displays the current Syslog setup settings for the router card.
show (router) uploaduser
Displays the current list of users allowed to upload and download
configuration and code files.
show (router-lan)
Displays the current LAN settings for the router card.
Axxius 800 - Release 2.2
Terminal Server Router Card
Card Configuration
l
l
l
l
l
l
l
l
l
l
l
l
l
show (router-lan) filter
Displays the current LAN Layer 2 data filters applied to the LAN on the
router card.
show (router-lan) static
Displays the current list of static entries for the LAN on the router card.
show (router-lan) stp
Displays the current Spanning Tree Protocol settings for the specified LAN
interface.
show (router-wan)
Displays the current configuration for the specified WAN.
show (router-wan) firewall
Displays the current firewall filter settings for the specified WAN interface.
show (router-wan) ppp
Displays the current PPP settings for the specified WAN interface.
show (router-wan) static ip address
Displays the current list of static IP address entries for the specified WAN
interface.
show (router-wan) static ip network
Displays the current list of static IP network entries for the specified WAN
interface.
show (router-wan) static mac address
Displays the current list of static IP MAC address entries for the specified
WAN interface.
show (router-wan) stp
Displays the current Spanning Tree Protocol settings for the specified WAN
interface.
show (router-wan) trunk
Displays the current trunk assignments for the specified WAN interface.
status (router)
Displays the current Router status information (alarms, DNS, events, IP
address table, IP network table, IPX network table, IPX server table, MAC
address table, performance, STP).
status (router-lan)
Displays the current router status information.
Axxius 800 - Release 2.2
15-15
Terminal Server Router Card
Card Configuration
l
l
l
15-16
status (router-trunk)
Displays the current state of the DNS resolver and the entries in the DNS
cache.
store
Save a software file from a slot to a defined location on a PC, via TFTP.
telnet (router)
Establish a Telnet session from the Axxius 800 CLI to the router port user
interface.
Axxius 800 - Release 2.2
Terminal Server Router Card
Connector Pinout
Connector Pinout
10Base-T Ethernet
1
8
The pinout for the RJ-48C (female) connectors on the front of the
card are as follows:
Pin
Name
Description
1
Receive +
Receive from network
2
Receive -
Receive from network
3
Transmit +
Transmit to network
4-5
N/C
Not connected
6
Transmit -
Transmit to network
7-8
N/C
Not connected
RS-232
If the card is set to use the RS-232 connector
(with jumpers) use the above RS-232 pinouts.
There is a RS-232 to DB-9 converter cable
available, P/N 005-0106.
The pinout is as follows:
RJ-45
DB-9
RS-232
1
8
CTS (Input)
2
7
RTS (Output)
3
6
DSR (Input)
4
3
TXD (Output)
5
2
RXD (Input)
6
1
DCD (Input)
7
4
DTR (Output)
8
5
SG (Filtered)
NA
9
RI (Not Used)
Axxius 800 - Release 2.2
1
8
1
5
6
9
15-17
Terminal Server Router Card
Connector Pinout
TSR Card Jumpers
The jumpers on the TSR card select the use of the 10/100Base-T (RJ-45) or RS-232.
There is one jumper for each port on the card. Each jumper can be set to
10/100Base-T or RS-232, independent of the others.
Connector
Placement
10/100Base-T
Position is farthest away from the front of the card
RS-232
Position closest to the front of the card
In the following graphic all port jumpers are set to 10/100Base-T Ethernet.
Card Front
15-18
Axxius 800 - Release 2.2
Terminal Server Router Card
LEDs
LEDs
The TSR service card has 2 LEDs per port.
At Power-up
TOP LED
Bottom LED
Description
Off
Off
Loss of power
Red
Red
Card is inoperative
Flashing Red
Flashing Red
Self-test or Boot in-process
TOP LED
Bottom LED
Description
Green Solid (Link)
Green Solid (Link)
Port set for Ethernet - see below
Flashing Red
Flashing Red
Self-test or Boot in-process
Normal Operation
Port Set for Ethernet
Top LED indicates 100M Link, Bottom LED indicates 10M Link
State
Description
Off
No Ethernet link
Green
Link but no activity
Red Flashing
Current Ethernet collision
Green Flashing
Current Ethernet receive
Yellow Flashing
Current Ethernet transmit
Port Set for RS-232
TOP LED
Bottom LED
Description
Yellow
Flashing Yellow
Current transmit
Yellow
Flashing Green
Current receive
Yellow
Off
No Activity
Axxius 800 - Release 2.2
15-19
Terminal Server Router Card
LEDs
15-20
Axxius 800 - Release 2.2
CHAPTER
V.35/.54 Card
In this Chapter
n
Overview
n
Features
n
Technical Specifications
n
Card Configuration
-
CLI Commands
n
Cables
n
Connector Pinouts
n
V.35 DCE (DB-26)
LEDs
V.35/.54 Card
Overview
Overview
The Hardened Dual V.35/.54 Service card enables wireless service providers to
provision connectivity to high-speed serial synchronous Data Terminal Equipment
(DTE) devices commonly deployed in the cell sites. V.35 service connections
supporting frame relay or transparent bit streams can be configured over one or more
T1 access lines to deliver DS0 bandwidths to wireless cell site devices such as CDPD,
RFFP and data routing equipment. This service card has been specifically hardened to
stand up to the extreme environmental conditions commonly associated with wireless
cell site deployments.
The V.35/.54 Service card provides scalable high-speed data service capacity to grow
as bandwidth requirements in the cell sites increase. Up to 8 V.35/.54 Service cards can
be equipped in an Axxius 800 platform. Integrated digital cross-connect System (DCS)
capability supports service grooming and full drop-and-insert functionality, features
not available in traditional CSU/DSU offerings.
Each V.35 port supports any n x 56/64 Kbps rate up to 1.536 Mbps. Both ports may
operate simultaneously at any supported speed. Flexible clocking options include loop
timing from any T1 line and the ability to supply system clock to the connected DTE,
allowing support for a wide range of data networking applications. Additionally, each
V.35 port supports V.54 loopback pattern recognition, generation and timing control to
troubleshoot service from the network or the end device to theV.35 electrical interface.
The V.35/.54 Service card can be locally or remotely managed as a component of the
Axxius 800 platform. The card can be configured using a Command Line Interface
(CLI) or via NetworkValet graphical interface.
16-2
Axxius 800 - Release 2.2
V.35/.54 Card
Features
Features
l Each port provides any n x 56/ 64 Kbps data rate up to 1.536 Mbps on each port
l Full non-blocking cross-connection of all timeslots to any T1 access line
l Up to 16 V.35 ports may be equipped in a single Axxius 800 platform
l Supports adaptation and tansport over TDM facilities
Additional V.54 Features
l V.54 Loop Test capability
Technical Specifications
Controller Software Required
l Release 1.0 or higher is required for the V.35/54 service card
Service Interface
l Two V.35 interfaces:
-
Configured as DCE
Two sub-miniature DB-26 connectors
DB26 to V.35 adapter cables available
Network Interface
l T1 N x DS0, where N = 1-24
Clocking
l Looped-timed from any T1 card installed
l Sources clock to the DTE device
Axxius 800 - Release 2.2
16-3
V.35/.54 Card
Technical Specifications
Testing and Diagnostics (V.35/54 card)
l Addressable V.54 loop up and loop down (127-code) pattern generation/
detection
l 2047, 215-1, 220-1 and QRSS Test Patterns with error counter
Power
l 2 W maximum
Environment
In addition to the systems environment requirements, the following applies to the
V.35/54 (hardened) card. For additional information see Installation Environment on
page 2-3.
l Operating temperature range of the V.35/54 card: -40° to 149° F
(-40° to 65° C)
Physical
l Dimensions: 3.5 in. (H) x 0.75 in. (W) x 11.25 in. (D)
8.9 cm (H) x 1.9 cm (W) x 28.6 cm (D)
l Weight: 4.6 oz. (0.13 kg)
Accessories
Sub-miniature DB-26 to Winchester adapter cables are required to interface DTE with
the Dual V.35 card. Gender refers to the Winchester connector. One cable per port.
l P/N 005-0008 V.35 Male 10 Ft. (3.05 m) cable
l P/N 005-0009 V.35 Male 25 Ft. (7.62 m) cable
l P/N 005-0010 V.35 Male 50 Ft. (15.24 m) cable
l P/N 005-0011 V.35 Female 10 Ft. (3.05 m) cable
16-4
Axxius 800 - Release 2.2
V.35/.54 Card
Card Configuration
Card Configuration
The V.35/54 card can be configured, using the Command Line Interface (CLI).
CLI Commands
The following commands are used to configure the V.35 cards. For detailed
information on these commands, see Chapter 5, CLI Commands.
l
l
l
l
l
l
connect
Creates two-way connections between channels.
disconnect
Removes a connection created by the connect command.
set (v35)
Setup of channels of a V.35 card (clock, clear to send, data, equipment, line,
receive clock invert, speed, transmit clock invert).
set (v54)
Set the V.54 loopback test parameters.
show (v54)
Displays the current settings for V.54 (CTS, timing, Rx clock inversion, Tx
clock inversion, data inversion, data speed, data rate, Rx LB, Rx Addr, test
address, Tx Prep count, Rx Prep count, test pattern, ignore ACK, loopback)
status (v54)
Displays the current near-end line status of the specified V.54 (DCD, CTS,
DSR, RTS, DTR, BERT).
Axxius 800 - Release 2.2
16-5
V.35/.54 Card
Cables
Cables
Depending on your application, you will need to purchase one or more of the available
Carrier Access Corporation V.35 data cables:
Part Number
Description
Notes
005-0014
V.35 Female
10-foot cable
005-0068
V.35 Female
25-foot cable
These cables are used to provide the V.35 DCE
interface on a male connector to typical DTE
applications. Order one cable per V.35 port.
005-0069
V.35 Female
50-foot cable
005-0010
V.35 Male
50-foot cable
005-0009
V.35 Male
25-foot cable
005-0008
V.35 Male
10-foot cable
005-0189
DB-25 V.35 Female
50-foot cable
005-0188
DB-25 V.35 Female
25-foot cable
005-0187
DB-25 V.35 Female
10-foot cable
005-0186
DB-25 V.35 Female
6-foot cable
V.35 data cables with male connector for
connecting a router with a female V.35
Winchester connector or other data equipment to
a Adit 600 V.35 data port (sub-miniature DB26). Order one cable per V.35 port.
These cables are used to provide a DB-25 DCE
V.35 female interface for connection to a male
DB-25 DTE V.35 interface. Order one per port.
These cables can be purchased at a licensed Carrier Access distributor.
16-6
Axxius 800 - Release 2.2
V.35/.54 Card
Connector Pinouts
Connector Pinouts
V.35 DCE (DB-26)
The V.35 DCE data port connection is made at the sub-miniature DB-26 connector on
the Axxius 800 using the 10-foot, 25-foot, or 50 foot Carrier Access DTE V.35 cable
equipped with a sub-miniature DB-26 connector and a 34-pin Winchester connector.
This cable is used to connect the Axxius 800 V.35 DCE data ports to synchronous V.35
DTE data sources up to 1.536 Mbps, all rates (1-24) Nx56 or Nx64 channel-rate
progression.
The Carrier Access Corporation V.35 data cables are built according to the pin
assignments listed below:
Sub-miniature
DB-26
Signal
Winchester 34-pin
(female)
Paired
Signals
1 (+ Shield)
←
Protective Ground →
A

7
←
Signal Ground →
B
2
←
Transmit Data A 
P


14
←
Transmit Data B 
S
3

Receive Data A →
R
16

Receive Data B →
T
4
←
RTS 
C
20
←
DTR 
H
5

CTS →
D
6

DSR →
E
12

Test Mode →
K
8

CD (RLSD) →
F
11
←
External Clock A 
U
24
←
External Clock B 
W
10

Xmit Clock A →
Y


23

Xmit Clock B →
AA

Axxius 800 - Release 2.2










16-7
V.35/.54 Card
Connector Pinouts
Sub-miniature
DB-26
Signal
Winchester
34-pin (female)
Paired
Signals
15

Receive Clock A →
V

17

Receive Clock B →
X
22
←
Local Loopback 
J


25
←
Remote Loopback 
BB

9, 13, 18
Open Pins/No Contact
19, 21, 26
Open Pins/No Contact
L, N, NN
LEDs
Each V.35 port has an LED, with definitions as shown in the table below.
16-8
State
Description
Off
No T1 Assignment
Green
Normal (CD/RTS) Active
Red
CD inactive (T1-side failure)
Yellow
RTS inactive (equipment-side failure)
Flashing Yellow
Loopback toward T1 or equipment loop test
Flashing Green
Loopback toward equipment or network loop test
Axxius 800 - Release 2.2
CHAPTER
Low Speed Protection Card
In this Chapter
n
Overview
n
Features
n
Technical Specifications
Card Configuration
- CLI Commands
- Basic Setup of a Protected System
n LEDs
n
Low Speed Protection Card
Overview
Overview
Low speed protection provides backup circuitry for any T1 service port on a Quad T1
service card or Quad DS1 ADPCM service card in the Axxius chassis. The Relay card
provides the physical connectivity between the “Protected” T1 service port and the
“Backup” T1 service port. Connectivity exists between the Service card and the Relay
card via the backplane pins only.
The service card slot that is configured for the “Backup card” is specified using CLI
commands. Additionally, the commands enable the user to specify what service card
(T1 or DS1 ADPCM) is to be protected and which port(s) on that card are to be
protected. In this manner, the protection card provides protection on an individual port
basis as opposed to a per card basis. Therefore protection is available for multiple cards
at the same time, as long as the port needing protection is not already being used by the
Backup card. For example if a Quad T1 card, slot 1, port 1 requires protection, the
Backup card port 1 is used to provide that protection. Ports 2-4 are still available for
protection on the remaining protected service cards.
A protected system can contain both T1 and DS1 ADPCM service cards. However, the
ADPCM mapping must be set the same on all cards in the protected system for Port #1
to be protected. Note: ports 2-4 are not effected by the ADPCM feature configuration.
See the following chart:
BACKUP CARD
17-2
PROTECTED CARD
T1 Service
Card
DS1 ADPCM Card
(ADPCM set to
"none")
DS1 ADPCM Card
(ADPCM set to "map1",
"map2" or "map3")
T1 Service Card
supported
supported
not supported
DS1 ADPCM Card
(ADPCM set to "none")
supported
supported
not supported
DS1 ADPCM Card
(ADPCM set to "map1",
"map2" or "map3")
not supported
not supported
supported
Axxius 800 - Release 2.2
Low Speed Protection Card
Overview
The Backup Card
A Quad T1 or Quad DS1 ADPCM service card can be configured as the “Backup card”.
The Backup card provides T1 port protection for other installed T1 service cards, and
can occupy any one of the eight service card slots.
Note: It is imperative that the slot designated for the backup card have NO wirewrap connections.
Protected Cards
The Quad T1/Quad DS1 ADPCM service cards to be protected can occupy any of the
7 remaining service card slots (backup card occupies the 8th slot). One or all four ports
can be protected, though each series of ports (all 1s, 2s, 3s and port 4s) have one backup
T1 port. The Axxius system can use other service cards in any of the 8 service card slots
without interference with the Low Speed Protection system.
Port Backup and Prioritization:
Priorities can be set for these protected ports (1-7) where 1 is the highest priority and
the default setting is 7. If more than 1 fault occurs at the same time the port with the
higher priority is granted the protection. In cases where traffic from a lower priority
port is already switched to backup, the traffic is forced back to the failed port to provide
the higher priority traffic with the backup port. When port protection requests are set at
the same level, protection is granted on a "first come, first serve" basis.
Ba
R
c k el a
up
y
Ca Ca r
T1 Protected Cards
d
rd
Above port #1 of the backup card provides a single T1 backup to all the protected T1’s,
port #1 in the system. This scenario is the same for the Backup port #2, port #3, and
port #4.
Axxius 800 - Release 2.2
17-3
Low Speed Protection Card
Features
Features
l Redundant 1:7 T1 interface protection
l Maintains service during card swaps
l Four T1 ports provide hot-standby backup for up to 28 T1 ports
l Any of the eight service slots can be designated as a Backup card slot
l Seven selectable protection priority levels
l Selectable 24-hour lockout feature
l Enables remote SNMP, or Telnet provisioning, monitoring and testing of services
and network conditions
Technical Specifications
Controller Software and Hardware Required
l Controller software Release 1.2 or higher is required for the Low Speed
Protection card
l Quad T1 Service cards (2 min.) requires Quad T1 Release 2.0 or higher
l Quad DS1 ADPCM Service cards (2 min.) Requires Controller Release 2.0 or
higher
Protection Capacity
l 1:7 T1 ports
Switchover Criteria
l Active card removal
l Line code violation count
l Loss of Signal/Loss of Frame
l All zeros
l Internally shorted pair
l Active card power loss
17-4
Axxius 800 - Release 2.2
Low Speed Protection Card
Technical Specifications
Service Cards Supported
l Quad T1 Service Card (hardened)
l DS1/E1 Service Card (hardened)
l Quad DS1 ADPCM Service Card (hardened)
Management
l RS-232/V.24 asynchronous craft port
l 10Base-T Ethernet management port
l Command Line Interface (CLI) from both the local asynchronous port and remote
Telnet sessions
l Menu-driven configuration and management interfaces
l SNMP agent for use with SNMP-based Element Management Systems
Alarms
l Switchover to hot-standby card
l Switchback to normal
Power
l 2.5 W maximum
Environment
In addition to the systems environment requirements, the following applies to the
Low-Speed Interface Protection Relay card. For additional information see Installation
Environment on page 2-3.
l Operating temperature range of the card: -40° to 149° F (-40° to 65° C)
Physical
l Dimensions: 3.5 in. (H) x 0.75 in. (W) x 11.25 in. (D)
8.9 cm (H) x 1.9 cm (W) x 28.6 cm (D)
l Weight: 7.4 oz. (0.21 kg)
Axxius 800 - Release 2.2
17-5
Low Speed Protection Card
Card Configuration
Card Configuration
CLI Commands
The following commands are used to configure the Low Speed Protection cards. For
detailed information on these commands, see Chapter 5, CLI Commands.
l
l
l
l
l
l
l
l
set lsbackup
Defines the backup protection slot.
set lsprotect enable/disable
Enables or disables the Low Speed Protection options on the system.
set lsprotect manual
Sets the manual mode control for protected ports.
set lsprotect nonrevertive
Defines the port non-revertive status and priority level.
set lsprotect remove
Removes port from protected mode.
set lsprotect revertive
Defines the port revertive status and priority level.
show lsprotect
Displays the low speed protection settings.
status lsprotect
Displays the current status of the low speed protection cards.
Basic Setup of a Protected System
To set up a Protected System, the following is required:
l
l
l
17-6
Axxius 800 with software 1.2 or higher
Low Speed Protection (Relay) card
2 - 6 Quad DS1/E1 or T1 Service Cards
1 designated as the Backup card, others to be protected
Axxius 800 - Release 2.2
Low Speed Protection Card
Card Configuration
Use the following steps to set up a Protected System.
1. Install a Relay card in the Axxius Relay slot.
2. Set the jumpers on the Quad T1 cards to route the signal to the wire-wrap pins,
see Jumper Settings on page 14-8 for detailed instructions.
3. Prewire the chassis for Quad T1 cards (wire-wrap pins).
Note: It is imperative that the slot designated for the Quad T1 backup
card have NO wire-wrap connections.
4. Install the Backup Quad T1 card into the designated service card slot (no
prewire).
5. Install Quad T1 cards that are to be protected into the prewired card slots.
Note: These QT1 cards can be in any slot, as well as other card types. Also
removal and/or replacement of any of these service cards will not effect
service to cards in adjacent slots.
Perform the following CLI commands to configure the system for protection.
Command
Description
set lsbackup {t1_card-addr}
This command defines the backup slot (can
be any slot)
set lsprotect enable
To enable the Low Speed Protection option
set lsprotect {slot:port}
{revertive|nonrevertive}
[priority] [1-7]
This command defines the protected cards.
Set all ports to revertive or non-revertive as
necessary with an optional priority level
show lsprotect
To display the current settings
status lsprotect
To display the current status
With the above steps protection is now provided for the specified cards. Any
single protected card can be pulled from its slot with only minimal interruption
to service. Since protection is on a 1xN basis once protection is provided for a
failed port other ports cannot be protected at the same time.
Axxius 800 - Release 2.2
17-7
Low Speed Protection Card
LEDs
LEDs
The Low Speed Protection card has 10 LEDs, which are defined below.
LED
State
Description
STAT
Green
Enabled
Red
Disabled
Off
The corresponding slot is not being protected
via the Protection card.
Yellow
One or more ports of the corresponding slot are
being protected via the Protection card.
Slot Status
(1-8)
Each channel on the Quad T1 card has two LEDs. The description of the top
LED is shown below, the bottom LED is not used with this application.
Quad T1 Backup Card
State
Description
Off
Not set up as Backup
Green
Port is switched to protection mode (the port it is protecting
will be flashing green)
Red
Displays red on backup card after other T1 port in same line
is set up to be protected
Flashing Green
Port is set up and ready to grant backup when needed
Flashing Yellow
Port is booting up to be backup card
Quad T1 Protected Card
17-8
State
Description
Off
Not set up as Backup
Green
Protected port is healthy and not in protected mode
Red
Displays red on backup card after other T1 port in same line
is set up to be protected
Flashing Green
Port has failed and the Backup card has granted protection
Flashing Yellow
Port is booting up to be backup card
Axxius 800 - Release 2.2
CHAPTER
Maintenance
In this Chapter
n
Software Loading
n
Upgrading Software Levels via XModem
Backup Axxius 800 Configuration
n
Loading System Software via TFTP
Save Controller Configuration
Load Controller Configuration
Hot Swap Service Card
Maintenance
Software Loading
Software Loading
Loading System Software via TFTP
1. Login to the Axxius 800, using a terminal emulation program or via Telnet.
NOTE: The tftp utility provided by Carrier Access with the downloadable
software must be running, in the same directory as the software file.
Command
Description
load standby tftp {ip-addr}
"file-name"
CLI command to load software to the Standby
Controller. See the load tftp command for
details.
reset standby
Do you really want to do
this ? Y
Reset the Standby Controller. You will be asked
to confirm this command, answer Y (Yes). See
reset (controller) command for details.
status equipment
Check the Standby Controller status, when it
displays hot standby go on to the next step. If hot
standby does not display stop here. If you go
further you may affect service. Start the
process again and if you are not successful call
Customer Service. See status equipment
command for more details.
switch controller
Set the signal clock switching. See the set clock
command for details.
Note: You will be disconnected from the unit when switching Controllers. Re-establish
connection with Axxius.
18-2
load standby tftp {ip-addr}
"file-name"
CLI command to load software to the Standby
Controller. See the load tftp command for
details.
reset standby
Do you really want to do
this ? Y
Reset the Standby Controller. You will be asked
to confirm this command, answer Y (Yes). See
reset (controller) command for details.
Axxius 800 - Release 2.2
Maintenance
Software Loading
Loading Router Software via TFTP
1. Login to the Axxius 800, using a terminal emulation program or via Telnet.
2. Enter:
load [rtr_card-addr] tftp {ip-addr} "file-name"
The tftp utility provided by Carrier Access with the downloadble software
must also be running, in the same directory as the software file.
3. After download, the program will be loaded from RAM into the flash memory
and the system will automatically restart. Wait until the boot menu prompt is
displayed before powering down the unit. If the download fails and no prompt
is seen after a full minute, cycle power and repeat the process.
4. Re-establish communication with the CLI using a terminal emulation program
or Telnet. Check all configurations and system operation.
Command
Description
load {rtr_card-addr} tftp
{ip-addr} "file-name"
CLI command to load software to the Standby
Controller. See the load tftp command for
details.
reset standby
Do you really want to do
this ? Y
Reset the Standby Controller. You will be asked
to confirm this command, answer Y (Yes). See
reset (controller) command for details.
status equipment
Check the Standby Controller status, when it
displays hot standby go on to the next step. If hot
standby does not display stop here. If you go
further you may affect service. Start the
process again and if you are not successful call
Customer Service. See status equipment
command for more details.
switch controller
Set the signal clock switching. See the set clock
command for details.
You will be disconnected from the unit when switching Controllers. Re-establish connection
with Axxius.
Axxius 800 - Release 2.2
18-3
Maintenance
Software Loading
18-4
Command
Description
load standby tftp {ip-addr}
"file-name"
CLI command to load software to the Standby
Controller. See the load tftp command for
details.
reset standby
Do you really want to do
this ? Y
Reset the Standby Controller. You will be asked
to confirm this command, answer Y (Yes). See
reset (controller) command for details.
Axxius 800 - Release 2.2
Maintenance
Software Loading
Upgrading System and Router Software via TFTP using
Proxy
Required:
- Router Service card (TSR) release 1.0 or higher
- Controller software 1.1 or higher
- Ethernet cable connected to port on front of Router card
1. Set up the Proxy with the following commands
set
set
set
set
ethernet ip address {ip-addr} [mask]
{rtr_lan-addr} ip address {ip-addr} [mask]
{rtr_card-addr} proxy enable {ip-addr} [mask]
ip gateway {ip-addr}
Example: (example with router in slot 3)
set
set
set
set
ethernet ip address 10.0.0.1 255.0.0.0
3:1 ip address 192.168.100.1/24
3 proxy enable 192.168.100.80/24
ip gateway 192.168.100.80
NOTE: See Chapter 5, CLI Commands for more information on these
commands.
1. Login to the Axxius 800 using the Proxy IP address, (example:
192.168.100.80) using a terminal emulation program or via Telnet.
2. Enter: load [slot] tftp {ip-addr} "file-name"
where [slot] = the slot number of a router card. If no slot number is listed, the
file is loaded to the Controller.
{ip-addr} = the IP address of the host device holding the downloadable
software
"file-name" = the software file name, including path, if needed. Enclosed in
quotes. Example: "c:\cac_sw\axxius1_0_z_all.mgm".
This example loads axxius1_0_z_all.mgm via tftp from the C drive and
CAC_sw subdirectory. The path information must be provided.
The tftp utility provided by Carrier Access with the downloadable software
must also be running, in the same directory as the software file.
Axxius 800 - Release 2.2
18-5
Maintenance
Software Loading
3. After download, the program will be loaded from RAM into the flash memory
and the system will automatically restart. Wait until the boot menu prompt is
displayed before powering down the unit. If the download fails and no prompt
is seen after a full minute, cycle power and repeat the process.
4. Re-establish communication with the CLI using a terminal emulation program
or Telnet. Check all configurations and system operation.
18-6
Axxius 800 - Release 2.2
Maintenance
Software Loading
Upgrading Software Levels via XModem
The following upgrade can also be performed through the POTS modem.
1. Login to the Axxius 800.
2. Enter: load {ctrlr-id} xmodem
to download the application from the binary file. This will start the system
looking for an xmodem download.
ctrlr_id
Controller identifier to download the software to.
A1, A2 All, Active or Standby. Note: Always load code to the
Standby Controller.
The Axxius 800 will prompt you to send the file. Use one of the following
methods:
Using HyperTerminal
l Pull down the Transfer menu
l Select Send File Provide the filename (and path if required), confirm
that the xmodem protocol is used for the transfer, and start the
download with the Send button
l A window will show the progress of the download.
Using Procomm
l Pull down the File menu
l Select Connection Directory
l Under the Data tab, use the Basic Options button to confirm that the
xmodem protocol is used for file transfers
l Pull down the Data menu, select Send File, provide the filename, and
start the download
Another Terminal Emulation Program
When using another terminal emulation program, confirm the use of xmodem
protocol at 9600 baud, provide filename (and path) and initiate the download.
Axxius 800 - Release 2.2
18-7
Maintenance
Software Loading
3. The binary file name is usually in the format: AxxiusAxxius.pkt. At 9600 baud,
the file transfer will take approximately 20 minutes.
4. After download, the program will be loaded from RAM into the flash memory
and the system will automatically restart. Wait until the boot menu prompt is
displayed before powering down the unit. If the download fails and no prompt
is seen after a full minute, cycle power and repeat the process.
5. Re-establish communication with the CLI using a terminal emulation program.
Check all configurations and system operation.
18-8
Axxius 800 - Release 2.2
Maintenance
Backup Axxius 800 Configuration
Backup Axxius 800 Configuration
A text file from the current configuration can be generated to reload the in the event the
configuration has been lost due to card or software problems. The download of the file,
generated by the print config command, can be done by direct connect to the
RS-232 port or via Telnet. The upload of the file from the PC back to the Axxius 800
can only be done via direct RS-232 connection. This is because the Axxius 800 will be
at factory default and an IP address is not assigned to the Axxius 800.
Save Controller Configuration
The following example is shown with a Hyperterm session, with Telnet selections in
parenthesis, other programs may be used and the process is similar, however the menu
selections may be different.
1. Start a HyperTerm session to an Axxius 800.
2. Type the CLI command print config and do not hit [ENTER].
3. Type select Transfer/Capture Text from the drop-down menu.
(Telnet - Terminal/Start Logging)
4. Name the file, select OK.
5. Return to the CLI command print config and hit [ENTER].
This process will exclude the print config command itself, from the
configuration file you are creating.
6. (Telnet - Select Terminal/Stop Logging).
7. Save configuration file as a .txt file, if necessary (Telnet will create a .log file,
which will need to be "saved as" a .txt file).
Axxius 800 - Release 2.2
18-9
Maintenance
Backup Axxius 800 Configuration
Load Controller Configuration
1. Open HyperTerm session with the Axxius 800 unit.
2. In HyperTerm, select File/Properties/Settings/ASCII Setup.
3. Set the Line delay to 300 ms and the Character delay to 5 ms.
4. Select OK to save ASCII Setup and OK to save Hyperterm Properties.
5. Select Transfer/Send Text File.
6. Select .txt file from previous steps.
7. Click Open.
8. Configuration will load.
18-10
Axxius 800 - Release 2.2
Maintenance
Hot Swap Service Card
Hot Swap Service Card
To Hot-Swap (replace) a service card while the unit is powered on, follow the steps
below:
1. Gently slide the Service card straight out of the slot.
2. Gently slide the new Service card into the empty slot.
3. Ensure that the new card is fastened securely into the connector at the back of
the unit.
Axxius 800 - Release 2.2
18-11
Maintenance
Hot Swap Service Card
18-12
Axxius 800 - Release 2.2
APPENDIX
Regulatory Approvals
In this Appendix
This appendix contains a chart of all the components of the Axxius 800 and
their Regulatory Approvals.
Regulatory Approvals
X
A-2
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
CS-03
ICES-003 Class A
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
CSA C22.2 No. 60950-00
FCC Part 15, Class A
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
NEBS Level 3 cert, type 2 & 4 equip
UL60950
A x x iu s 8 0 0 C h a s s i s
D S 3 C o n t ro ll e r
D S 1 C o n t ro ll e r
L o w S p e e d P ro t e c t i o n
F XO
IS D N B R I
O C U -D P
P O TS
Q uad DS 1 A DP CM
Q uad D S 1/E 1
Q u a d T1
V . 3 5 / 5 4 (h a rd e n e d )
T S R (1 . 2 )
24 V DC P S
4 8 V D C P S N I4 8
4 8 V D C P S I4 8
Canada
FCC Part 68
USA
A x x i u s 8 0 0 C h a ssi s
X
X
X
X
X
X
X
M e e t s t h i s c o m p l ia n c e
D o e s n o t m e e t t h is c o m p l ia n c e
D e s ig n e d t o m e e t N E B s (n o t C e r t ifie d )
Axxius 800 - Release 2.2
APPENDIX
SNMP Interface
In this Appendix
n
Overview
n
SNMP Basics
n
Enterprise MIB Support
n
Router Enterprise MIB Support
n
Public MIB Support
n
Router Public MIB Support
n
SNMP Trap Reports
SNMP Interface
Overview
Overview
The Simple Network Management Protocol (SNMP) enables network operations
centers (NOCs) to monitor and manage network elements across an internetwork. The
Axxius 800 supports SNMP through its Ethernet port, which provides access to the
carrier’s TCP/IP management network.
SNMP Basics
SNMP is a mechanism for managing TCP/IP networks. It works by exchanging
information between an SNMP Manager and an SNMP Agent.
Carrier Access also offers NetworkValet® EMS, Java-based SNMP management
programs for Windows and Solaris computers, that provide a graphical user interface
to simplify management of the Axxius 800 and other Carrier Access products.
MIB Structure
The SNMP Agent displays network information in a Management Information Base
(MIB). MIBs are machine-to-machine interfaces that arrange and present information
according to industry standards such as RFC 1213. MIBs are tree-like structures
comprising nodes and leaves. Nodes are branch points used to divide information into
categories. Leaves have object values that can be examined and changed. Common
MIB objects include system names, performance statistics, and control values.
Control values are typically Integer types. This enables the object’s value to represent
a specific control selection. Selections are usually written in the “name(value)” format.
For example, the selection “closed(1)” means that the “closed” state is indicated by a
value of “1”.
B-2
Axxius 800 - Release 2.2
SNMP Interface
Enterprise MIB Support
Enterprise MIB Support
This release is with full SNMPv1 and SNMPv2c support. Enterprise MIBs are defined
using only SMIv2 (as noted in the table).
Enterprise MIB Name
Enterprise MIB Filename
Axxius-SYSTEM-MIB
Axxius-system.mib
Axxius-DS1-MIB
Axxius-ds1.mib
Axxius-DS3-MIB
Axxius-ds3.mib
CARRIERACCESS-GENERIC- MIB
carrieraccess-generic.mib
CARRIERACCESS-TC-MIB
carrieraccess-tc.mib
CAGEN-GENERIC-MIB
cagen-generic.mib
CAGEN-SLOT-MIB
cagen-slot.mib
CAGEN-SYSTEM-MIB
cagen-system.mib
CAGEN-ALARM-MIB
cagen-alarm.mib
CAGEN-EVENT-MIB
cagen-event.mib
CAGEN-TRAPS-MIB
cagen-traps.mib
CAGEN-DS0-MIB
cagen-ds0.mib
CAGEN-DS1-MIB
cagen-ds1.mib
CAGEN-DS3-MIB
cagen-ds3.mib
CAGEN-FX-MIB
cagen-fx.mib
CAGEN-V35-MIB
cagen-v35.mib
CAGEN-TSR-MIB
cagen-tsr.mib
CAGEN-BRI-MIB
cagen-bri.mib
CAGEN-OCUDP-MIB
cagen-ocudp.mib
CAGEN-IF-FACTORY-MIB
cagen-if-factory.mib
Axxius 800 - Release 2.2
B-3
SNMP Interface
Router Enterprise MIB Support
Router Enterprise MIB Support
Enterprise MIB Name
Enterprise MIB Filename
Router Specific
CAGENROUTER-CARDPROFILE-MIB
caGenRouter-CardProfile.mib
CAGENROUTER-FILTERS-MIB
caGenRouter-Filters.mib
CAGENROUTER-LANPROFILE-MIB
caGenRouter-LanProfile.mib
CAGENROUTER-MANAGEMENT-MIB
caGenRouter-Mgt.mib
CAGENROUTER-REPORTS-MIB
caGenRouter-Reports.mib
CAGENROUTER-SPANTREE-MIB
caGenRouter-SpanTree.mib
CAGENROUTER-STATIC-MIB DEFINITIONS
caGenRouter-Static.mib
CAGENROUTER-DNS-MIB
caGenRouter-DNS.mib
CAGENROUTER-NTPPROFILE-MIB
caGenRouter-NTPProfile.mib
CAGENROUTER-TRUNK-MIB
caGenRouter-Trunk.mib
CAGENROUTER-WANPROFILE-MIB
caGenRouter-WanProfile.mib
CAGENROUTER-MIB
caGenRouter.mib
CAGENROUTER-TC-MIB
caGenRouter-tc.mib
CAGENTSR-MIB
caGenTsr.mib
Common with Controller
B-4
CARRIERACCESS-GENERIC-MIB
carrieraccess-generic.mib
CARRIERACCESS-TC-MIB
carrieraccess-tc.mib
CAGEN-GENERIC-MIB
cagen-generic.mib
CAGEN-SYSTEM-MIB
cagen-system.mib
CAGEN-TSR-MIB
cagen-tsr.mib
Axxius 800 - Release 2.2
SNMP Interface
Public MIB Support
Public MIB Support
MIB
RFC1155
(RFC-1155-smi.MIB)
RFC1212
(RFC-1212.MIB)
Table
Comments
RFC1213 (RFC-1213-MIB)
system
interfaces
ip
icmp
tcp
udp
snmp
egp not supported
Supports V.35 Card
Rs232AsnycPortTable
not supported
IANAifType-MIB
rs232PortTable
rs232SyncPortTable
rs232InSigTable
rs232OutSigTable
system
sysORTable
snmp
ip
ipAddrTable
ipNetToMediaTable
icmp
ifTable
ifXTable
ifStackTable
IANAifType
RFC2493 (PerHist-TC-MIB)
Performance History TC
RFC1215
(RFC-1215.MIB)
RFC1215-TRAP
(RFC-1215-TRAP.MIB)
RFC1659 (RFC1659-MIB)
RFC1907 (SNMPv2-MIB)
RFC2011 (IP-MIB)
RFC2233 (IF-MIB)
Axxius 800 - Release 2.2
SMIv2 Extension of
RFC1213
SMIv2 Extension of
RFC1213
IfTestTable,
ifRcvAddressTable not
supported
Used by RFC2233; no
objects
Defines textual
conventions; no objects
B-5
SNMP Interface
Public MIB Support
MIB
Table
Comments
RFC2494 (DS0-MIB,
DS0BUNDLE-MIB)
dsx0ConfigTable
dsx0ChanMappingTable
dsx0BundleTable
dsx1ConfigTable
dsx1CurrentTable
dsx1IntervalTable
dsx1TotalTable
dsx3ConfigTable
dsx3CurrentTable
dsx3TotalTable
dsx3FarEndConfigTable
dsx3FarEndCurrentTable
dsx3FarEndIntervalTable
dsx3FarEndTotalTable
SNMP TC
Dsx0BondingTable not
supported
RFC2495 (DS1-MIB)
RFC2496 (DS3-MIB)
RFC2571 (SNMPFRAMEWORK-MIB)
Far End Tables and
Fractional Table not
supported
dsx3FracTable not
supported
Defines textual
conventions1 no objects
RFC3291 (RFC3291-MIB)
SNMPV2-CONF-MIB
SNMPV2-SMI-MIB
SNMPV2-TC-MIB
B-6
Axxius 800 - Release 2.2
SNMP Interface
Router Public MIB Support
Router Public MIB Support
MIB
RFC1213 (RFC-1213-MIB)
RFC1907 (SNMPv2-MIB)
Table
system
interfaces
ip
icmp
tcp
udp
snmp
system
snmp
RFC2011 (IP-MIB)
ip
icmp
RFC2233 (IF-MIB)
ifTable
IANAifType-MIB
IANAifType
Axxius 800 - Release 2.2
Comments
egp not supported
SMIv2 Extension of
RFC1213 SysORTable not
supported
SMIv2 Extension of
RFC1213.
IpAddrTable not supported.
Routing table and
ipNetToMediaTable
supported by Enterprise mibs.
IfTestTable,
ifRcvAddressTable,
ifXTable, ifStackTable not
supported
Used by RFC2233; no objects
B-7
SNMP Interface
SNMP Trap Reports
SNMP Trap Reports
The Axxius 800 can send the following SNMP trap reports.
Standard Traps
Trap
Description
Test Method
authentication Occurs when a bad community string is used.
Failure
Attempt a Get or Set
using an invalid
community string.
linkDown
Sent when a DS1 changes from an up (in-service) state to Disconnect an ina down (out-of-service) state. It is not sent when a DS1 is service DS1.
set “down” by a manual command.
Also sent when a DS1 is set up manually, if it is in an outof-service state.
linkUp
Sent when a DS1 changes from a down (out-of-service)
state to an up (in-service) state. It is not sent when a DS1
is set “up” by a manual command.
coldStart
Sent whenever the SNMP agent is restarted as a result of a Cycle the power off
software reset or unit powerup.
and on.
Connect a DS1 and
put it into service.
Enterprise Traps
Trap
Description
Test Method
caGenEventLo This trap is generated when an event has been logged into the
gTrap
device's Event Log. This trap contains 5 mandatory variable
bindings and may contain up to 3 optional variable bindings.
The mandatory variable bindings are caGenEventLogIndex,
caGenEventSeverity, caGenEventCategory,
caGenEventCode, and caGenEventDate. The optional
variable bindings are caGenEventInfoParam1,
caGenEventInfoParam2 and caGenEventAdditionalText. The
optional variable bindings (if present) will always appear at
the end of the variable binding list.
B-8
Axxius 800 - Release 2.2
APPENDIX
Loopback Tests
In this Appendix
n
Overview
n
DS1 Loopbacks
n
V.35 Loopbacks
n
V.35/V.54 Loop
Loopback Tests
Alarms
Alarms
Test Alarm
The Axxius 800 alarm functions can be manually tested using the following command
for setting critical, major and minor alarms. Turning alarms on or off will produce
alarm messages and log entries stating the alarm event was manually set/cleared by the
user.
Syntax: set alarms {critical|major|minor} {off|on}
Identify Alarm
Alarm indicators
l
LEDs - When an Alarm is triggered, the LED will display a red/yellow
indicator light, which will stay on until the Alarm is cleared. The following
is the LED information for the Control Panel Interface card. For LED
information for a specific service card see the chapter for that card.
LED
State
Description
CRITICAL
Off
No critical alarms present
Red
Critical alarms present
Off
No major alarms present
Red
Major alarm present
Off
No minor alarms present
Red
Minor alarms present
Off
Normal mode. No alarms are being
suppressed.
Red
Alarm cutoff active. One or more active
alarms suppressed.
MAJOR
MINOR
ACO
C-2
Axxius 800 - Release 2.2
Loopback Tests
Alarms
The following are hyperlinks to all the card LED information:
DS1 Controller Card, LEDs
DS3 Controller Card, LEDs
FXO Voice Card, LEDs
ISDN BRI Card, LEDs
OCU-DP Card, LEDs
Single Channel POTS Cards, LEDs
Quad DS1 ADPCM Card, LEDs
Quad T1 & Quad DS1/E1 Card, LEDs
Terminal Server Router Card, LEDs
V.35/.54 Card, Connector Pinouts
Low Speed Protection Card, LEDs
Power Supply, LEDs
Axxius 800 - Release 2.2
C-3
Loopback Tests
Alarms
Display Alarms
Use the alarms command to display the active alarms. Each alarm is related to a
particular address and has a severity category (major, minor, critical, alert). The
report can be filtered by port address and/or severity.
Syntax: alarms [slot|slot:port|slot:port:channel] [category]
[severity]
> alarms
Time
07:35:45
07:35:21
07:34:57
00:00:20
00:00:05
00:00:05
Total=6
Date
Severity Description
01/04/2002 Major
Test Major Alarm
01/04/2002 Minor
Test Minor Alarm
01/04/2002 Critical Test Critical Alarm
01/01/2002 Major
6:1-TSR Ethernet Link Down
01/01/2002 Major
A:2-DS1 Loss Of Signal
01/01/2002 Major
A:1-DS1 Loss Of Signal
Category = bri|ds1|env|equipment|fxo|fxs|rtr|v35
Severity = alert|critical|info|major|minor
Clear Alarm
Once an alarm is identified then the process of clearing it can begin.
l
l
l
l
l
C-4
Silence Alarm, if necessary (Alarm Cut Off CLI command: aco)
Check Connection
Check Cable, replace if necessary
Check hardware and replace if necessary
Call Customer Service
Axxius 800 - Release 2.2
Loopback Tests
Logs
Logs
Display the event log to view a log of all system events, or narrow the view to only
display specific information.
Syntax: log [slot|slot:port] [category] [severity]
Example: log
Time
Date
Severity Description
----
----
-------- -------------------------------
00:00:11 01/01/2002 Info
8-FXSPSMx1 Card Detected
00:00:10 01/01/2002 Major
A:2:1-DS1 Loss Of Frame
00:00:10 01/01/2002 Major
A:1:1-DS1 Loss Of Frame
00:00:09 01/01/2002 Major
A:2:28-DS1 Loss Of Frame
00:00:09 01/01/2002 Major
A:2:27-DS1 Loss Of Frame
00:00:09 01/01/2002 Major
A:2:26-DS1 Loss Of Frame
00:00:08 01/01/2002 Major
A:2:20-DS1 Loss Of Frame
00:00:08 01/01/2002 Major
A:2:19-DS1 Loss Of Frame
00:00:08 01/01/2002 Major
A:2:18-DS1 Loss Of Frame
00:00:04 01/01/2002 Info
6-V35x2H Card Detected
00:00:02 01/01/2002 Info
Transmit Clock Source:Internal
00:00:02 01/01/2002 Info
A-T3x2 Card Detected
00:00:01 01/01/2002 Info
A1-Became The Active Controller
00:00:01 01/01/2002 Info
System Powerup
Total=14
Category = bri|ds1|env|equipment|fxo|fxs|rtr|v35
Severity = alert|critical|info|major|minor
Axxius 800 - Release 2.2
C-5
Loopback Tests
Status and Performance
Status and Performance
The following status commands will display vital information regarding the system that
will aid in troubleshooting. All commands listed below are hyperlinked to the CLI
command.
status (adpcm)
status (bri)
status clock
status (ds0)
status (ds1)
status (ds3)
status equipment
status (fxo)
status (fxsPS or fxsPSM)
status ipds0
status (ocudp)
status (router)
status (router-lan)
status (router-trunk)
status (v54)
C-6
Axxius 800 - Release 2.2
Loopback Tests
Overview
Overview
A loopback test is a diagnostic procedure in which a signal is transmitted and returned
to the sending device after passing through all or a portion of a network or circuit. The
returned signal is compared with the transmitted signal in order to evaluate the integrity
of the equipment or transmission path.
DS1 Loopbacks
Note: T1 LEDs flash green during any DS1 loopback.
DS1 Line Loop
Loops at DS1 (at framer), signal not reframed. Have DS1 vendor check for framing/
errors.
Local
DTE
Local
DCE
V.35
T1
DS1
Network
Axxius
Loops DS1 as shown
Signal Not Reframed
Enable Line Loopback
> set a:1 line loopup
OK
Axxius 800 - Release 2.2
C-7
Loopback Tests
DS1 Loopbacks
View Status of Loopback
> status a:1
SLOT A:
Status for DS1
Receive:
Transmit:
Loopback:
1:
Traffic
Traffic
LINE
Disable Line Loopback
> set a:1 line loopdown
OK
View Status of Loopback
> status a:1
SLOT A:
Status for DS1
Receive:
Transmit:
Loopback:
C-8
1:
Traffic
Traffic
OFF
Axxius 800 - Release 2.2
Loopback Tests
DS1 Loopbacks
DS1 Payload Loop
Loops at DS1 (in framer) and reframes the T1. Have DS1 vendor check for framing/
errors.
Local
DTE
Local
DCE
V.35
T1
DS1
Network
Axxius
Loops DS1 as shown
Reframes the T1
Enable Payload Loopback
> set a:1 payload loopup
OK
View Status of Loopback
> status a:1
SLOT A:
Status for DS1
Receive:
Transmit:
Loopback:
1:
Traffic
Traffic
PAYLOAD
Disable Payload Loopback
> set a:1 payload loopdown
OK
View Status of Loopback
> status a:1
SLOT A:
Status for DS1
Receive:
Transmit:
Loopback:
Axxius 800 - Release 2.2
1:
Traffic
Traffic
OFF
C-9
Loopback Tests
DS1 Loopbacks
Receiving DS-1 CSU Loop
Causes a line Loopback. Loopup code sent by remote unit or network. Occurs at local
DS1 CSU. Have DS1 vendor check for framing/errors.
Local
DTE
Local
DCE
V.35
T1
CSU Loopup
Code
DS1
Network
Axxius
Loopup Code Sent by Remote Unit
Signal Not Reframed
Enable Detection of CSU Loopcode
Enable detection of CSU loop code (10000 for loopup; 100 for loopdown).
> set a:1 loopdetect on
OK
C-10
Axxius 800 - Release 2.2
Loopback Tests
DS1 Loopbacks
View Status of Loopback
> show a:1
SLOT A:
Settings for DS1 1:
Circuit ID:
Up/Down:
Framing:
Line Coding:
Line Build Out:
(CSU 0dB)
Loop Code Detection:
Loopback:
FDL Type:
CAC DS1# A:1
UP
ESF
B8ZS
DSX-1 EQUALIZATION FOR 0-133 ft.
ON (Default)
OFF
None
Performance Threshold Settings
unavailable seconds:
severely errored seconds:
errored seconds:
sev. errored frame seconds:
line errored seconds:
controlled slip seconds:
bursty errored seconds:
degraded minutes:
total linecode violations:
total pathcode violations:
> status a:1
SLOT A:
Status for DS1
Receive:
Transmit:
Loopback:
Axxius 800 - Release 2.2
15 min.
0
0
0
0
0
0
0
0
0
0
1 day
0
0
0
0
0
0
0
0
0
0
1:
Traffic
Traffic
LINE
C-11
Loopback Tests
DS1 Loopbacks
DS1 Equipment Loop
Note: Quad T1 LED flashes green during equipment loop.
Local
DTE
Local
DCE
V.35
T1
DS1
Network
Axxius
Loops DS1 as shown
Enable Equipment Loopback
Where a Quad T1 card is in slot 5.
> set 5:1 equipment loopup
OK
View Status of Loopback
> show 5:1
SLOT 5:
Settings for DS1 1:
Circuit ID:
Up/Down:
Framing:
Line Coding:
Line Build Out:
(CSU 0dB)
Loop Code Detection:
Loopback:
FDL Type:
CAC DS1# 5:1
UP
ESF
B8ZS
DSX-1 EQUALIZATION FOR 0-133 ft.
ON
EQUIPMENT
None
Performance Threshold Settings
unavailable seconds:
severely errored seconds:
C-12
15 min.
0
0
1 day
0
0
Axxius 800 - Release 2.2
Loopback Tests
DS1 Loopbacks
errored seconds:
sev. errored frame seconds:
line errored seconds:
controlled slip seconds:
bursty errored seconds:
degraded minutes:
total linecode violations:
total pathcode violations:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Disable Equipment Loopback
> set 5:1 equipment loopdown
OK
View Status of Loopback
> show 5:1
SLOT 5:
Settings for DS1 1:
Circuit ID:
Up/Down:
Framing:
Line Coding:
Line Build Out:
(CSU 0dB)
Loop Code Detection:
Loopback:
FDL Type:
CAC DS1# 5:1
UP
ESF
B8ZS
DSX-1 EQUALIZATION FOR 0-133 ft.
ON
OFF
None
Performance Threshold Settings
unavailable seconds:
severely errored seconds:
errored seconds:
sev. errored frame seconds:
line errored seconds:
controlled slip seconds:
bursty errored seconds:
degraded minutes:
total linecode violations:
total pathcode violations:
Axxius 800 - Release 2.2
15 min.
0
0
0
0
0
0
0
0
0
0
1 day
0
0
0
0
0
0
0
0
0
0
C-13
Loopback Tests
V.35 Loopbacks
V.35 Loopbacks
V.35 Line Loop
Note: V.35 LED flashes green during line loop.
Loop occurs at V.35 port. Check for sync and errors at local data port.
Local
DTE
Local
DCE
V.35
Axxius
T1
Line
Loopback
Enable Line Loopback
Where a V.35 card is in slot 6.
> set 6:1 line loopup
OK
View Status of Loopback
> show 6:1
SLOT 6:
Settings for V35 Port 1:
CTS:
Timing:
Rx Clock Inversion:
Tx Clock Inversion:
Data Inversion:
Data Speed:
Data Rate:
Loopback:
C-14
Always High
Source
Normal
Normal
Normal
64K
1536 K
Line
Axxius 800 - Release 2.2
Loopback Tests
V.35 Loopbacks
Disable Line Loopback
> set 6:1 line loopdown
OK
View Status of Loopback
> show 6:1
SLOT 6:
Settings for V35 Port 1:
CTS:
Timing:
Rx Clock Inversion:
Tx Clock Inversion:
Data Inversion:
Data Speed:
Data Rate:
Loopback:
Axxius 800 - Release 2.2
Always High
Source
Normal
Normal
Normal
64K
1536 K
None
C-15
Loopback Tests
V.35 Loopbacks
V.35 Equipment Loop
Note: V.35 LED flashes yellow during equipment loop.
Loops at local V.35 port. Check for sync and errors at remote data port, with or without
BERT.
Local
DTE
Equipment
Loopback
Local
DCE
V.35
T1
Axxius
Enable Equipment Loopback
Where a V.35 card is in slot 6.
> set 6:1 equipment loopup
OK
View Status of Loopback
> show 6:1
SLOT 6:
Settings for V35 Port 1:
CTS:
Timing:
Rx Clock Inversion:
Tx Clock Inversion:
Data Inversion:
Data Speed:
Data Rate:
Loopback:
C-16
Always High
Source
Normal
Normal
Normal
64K
1536 K
Equipment
Axxius 800 - Release 2.2
Loopback Tests
V.35 Loopbacks
Disable Equipment Loopback
> set 6:1 equipment loopdown
OK
View Status of Loopback
> show 6:1
SLOT 6:
Settings for V35 Port 1:
CTS:
Timing:
Rx Clock Inversion:
Tx Clock Inversion:
Data Inversion:
Data Speed:
Data Rate:
Loopback:
Axxius 800 - Release 2.2
Always High
Source
Normal
Normal
Normal
64K
1536 K
None
C-17
Loopback Tests
V.35/V.54 Loop
V.35/V.54 Loop
V.35/V.54 Service Card Description
The V.35 Card with V.54 Loop Test provides the capability for the V.35 card to detect
network loop back initiation signals and provide a network loop back for loop testing.
Each channel of the V.35 will continuously monitor the incoming data bit stream for a
particular loop pattern. On detection of the pattern the channel will acknowledge the
loop test request and put the channel into loop back. The channel will then continuously
monitor for the loop test end pattern. On detection of the loop end pattern the channel
will remove loop back and resume normal operation. Front panel LED’s will indicate
Loop test. Each channel can also initiate the loop test pattern causing another V.54
compatible device to loop back. The channel will then transmit a test pattern and
calculate bit error rate (BER).
View V.35/V.54 Card Configuration
Where a V.35/V.54 card is in slot 6.
> show 6:1
SLOT 6:
Settings for V35 Port 1:
CTS:
Timing:
Rx Clock Inversion:
Tx Clock Inversion:
Data Inversion:
Data Speed:
Data Rate:
V.54 Rx LB:
V.54 Rx Addr:
V.54 Test Addr:
V.54 Tx Prep count:
V.54 Rx Prep count:
V.54 Test Pattern:
V.54 Ignore ACK:
Loopback:
C-18
Always High
Source
Normal
Normal
Normal
64K
768 K
disabled
255
255
15
15
QRSS
OFF
None
Axxius 800 - Release 2.2
Loopback Tests
V.35/V.54 Loop
V.54 Loop
Note: Local LED flashes yellow, remote LED flashes green.
Local
DTE
Local
DCE
V.35
T1
Remote
DCE
V.35
T1
Remote
DTE
Network
Axxius
Equipment
Unit
Axxius
Network
Unit
V.54
Loopback
Enable V.54 Loop
Where a V.35/V.54 card is in slot 6.
> set 6:1 v54 network enable
OK
View Status of Loopback
> show 6:1
SLOT 6:
Settings for V35 Port 1:
CTS:
Timing:
Rx Clock Inversion:
Tx Clock Inversion:
Data Inversion:
Data Speed:
Data Rate:
V.54 Rx LB:
V.54 Rx Addr:
V.54 Test Addr:
V.54 Tx Prep count:
V.54 Rx Prep count:
V.54 Test Pattern:
V.54 Ignore ACK:
Loopback:
Axxius 800 - Release 2.2
Always High
Source
Normal
Normal
Normal
64K
768 K
enabled
255
255
15
15
QRSS
OFF
None
C-19
Loopback Tests
V.35/V.54 Loop
V.54 Equipment Loopback
Enable V.54 Equipment Loopup
Where a V.35/V.54 card is in slot 6.
> set 6:1 v54 equipment loopup
OK
View Status of Loopback
> show 6:1
SLOT 6:
Settings for V35 Port 1:
CTS:
Timing:
Rx Clock Inversion:
Tx Clock Inversion:
Data Inversion:
Data Speed:
Data Rate:
V.54 Rx LB:
V.54 Rx Addr:
V.54 Test Addr:
V.54 Tx Prep count:
V.54 Rx Prep count:
V.54 Test Pattern:
V.54 Ignore ACK:
Loopback:
Always High
Source
Normal
Normal
Normal
64K
768 K
enabled
255
255
15
15
QRSS
OFF
Equipment(V.54)
> status 6:1
SLOT 6:
Status for V35 PORT 1:
DCD:
High
CTS:
High
DSR:
High
RTS:
High
DTR:
High
BERT:
RUNNING (Syncing up)
C-20
Axxius 800 - Release 2.2
Loopback Tests
V.35/V.54 Loop
> status 6:1
SLOT 6:
Status for V35 PORT 1:
DCD:
High
CTS:
High
DSR:
High
RTS:
High
DTR:
High
BERT:
RUNNING
BITS:
8386950
ERRS:
0
BER:
0.00000000
Disable V.54 Equipment Loopup
> set 6:1 v54 equipment loopdown
OK
View Status of Loopback
> status 6:1
SLOT 6:
Status for V35 PORT 1:
DCD:
High
CTS:
High
DSR:
High
RTS:
High
DTR:
High
BERT:
Complete
BITS:
109030350
ERRS:
0
BER:
0.00000000
BERT DATE:
1/5/2001 01:39:18
Axxius 800 - Release 2.2
C-21
Loopback Tests
V.35/V.54 Loop
C-22
Axxius 800 - Release 2.2
GLOSSARY
Glossary
10Base-T
The most widely installed Ethernet local area networks (LANs) use
ordinary telephone twisted-pair wire. When used on Ethernet, this carrier
medium is known at 10BASE-T. 10BASE-T supports Ethernet’s 10
Mbps transmission speed.
100Base-TX
100Base-TX is a 100 Mbps local area network, know as Fast Ethernet.
ADPCM
Adaptive Differential Pulse Code Modulation. A speech coding method
which uses fewer bits than the traditional PCM (Pulse Code Modulation).
ADPCM allows encoding of voice signals in half the space PCM allows.
Annex D
A frame relay standard extension dealing with the communication and
signaling between customer premises and equipment and frame relay
network equipment for the purpose of querying network status
information.
Analog
The telephone transmission of voice, video or image. Telephone
transmission and/or switching that is not digital.
authentication
The process of identifying an individual, usually based on a username
and password combination, although the process can be many more
steps. In security systems, authentication is distinct from authorization,
which is the process of giving individuals access to system objects based
on their identity. Authentication merely ensures that the individual is
who he or she claims to be, but says nothing about the access rights of the
individual. Authentication in whatever form, is usually followed by
authorization.
Glossary
authorization
authorization
The process of granting or denying access to a network resource. Most
computer security systems are based on a two-step process, sometimes
more. The first stage is authentication, which ensures that a user is who
he or she claims to be and in some cases, that the user is not already on
the system. The second stage is authorization, which allows the user
access in varied degrees to various resources based on the preassigned
privileges associated with the user’s identity.
B-channel
Short for Bearer-channel, the main data channel in an ISDN connection.
Basic Rate ISDN (BRI) service consists of two 64 Kbps B-channels, and
one D-channel for transmitting control information.
B8ZS
Bipolar 8-Zero Substitution, a coding scheme that maintains ones
density.
backplane
A common bus at the rear of the computer chassis connecting each circuit
card slot to the other parts of the system. Motherboards on modern PCs
are a general equivalent. It also distributes low-voltage AC and DC,
filtered and un-filtered power to each slot.
bandwidth
The amount of data that can travel through a channel in a given period of
time. Bandwidth is usually measured in cycles per second (hertz) or in
bits per second (BPS). The larger the bandwidth, the more information
the network can handle. ISDN is usually 64KB, 128KB or 256KB.
ASDL and DSL are generally faster than ISDN and sometimes faster
than cable. Cable connections are usually 500KB or 1MB. T1 is 1.5MB
and T3 is 45MB.
Basic Rate
Interface (BRI)
Basic Rate Interface is an Integrated Services Digital Network (ISDN)
interface typically used by smaller sites and customers. This interface
consists of a single 16 Kbps Data (or "D") channel plus 2 Bearer (or "B")
channels for voice and/or data.
BER
Bit Error Rate, the number of erred bits divided by the total number of
bits.
BERT
Bit Error Rate Tester
Glossary - 2
Axxius 800 - Release 2.2
Glossary
bipolar
bipolar
The predominant signaling method used for digital transmission
services, such as DDS and T1. The signal carrying the binary value
alternates between positive and negative. Zero and one values are
represented by the signal amplitude at either polarity, while no-value
"spaces" are at zero amplitude.
Bipolar
Violation (BPV)
The presence of two consecutive "one" bits of the same polarity on the T
carrier line.
bit
Contraction of the words "binary" and "digit".
Bit Error Rate
Test (BERT)
A test that reflects the ratio of errored bits to the total number transmitted.
Usually shown in exponential form (10^-6) to indicate that one out of a
certain number of bits are in error.
bit robbing
Telephony coined phrase to describe a transmission process. The
technique in T1 multiplexing in which the least significant bit (bit 8) of
each byte in selected frames is "robbed" from being used to carry
message information, and instead is used to carry signaling information.
bps
Bits per second
BPV
Bipolar Violation.
BRI
Basic Rate Interface (2b+d) in ISDN.
bridge
A bridge is any hardware device that connects two physically distinct
network segments, usually at a lower network layer than would a router,
however the two terms are often interchanged. A device that connects
two local-area networks (LANs), or two segments of the same LAN. The
two LANs being connected can be alike or dissimilar. Unlike routers,
bridges are protocol independent. They simply forward packets without
analyzing and re-routing messages. Consequently, they’re faster than
routers, but also less versatile.
Axxius 800 - Release 2.2
Glossary - 3
Glossary
broadband
broadband
A technology that provides an extremely wide and fast bandwidth so that
many people can simultaneously use the service. It is generally
associated with multiple types of transmissions on the same connection
such as voice, data, video and digital or analog information.
C-bit Coding
Violation
(CCV)
For C-bit Parity and SYNTRAN DS3 applications, this is the count of
coding violations reported via the C-bits. For C-bit Parity, it is a count of
CP-bit parity errors occurring in the accumulation interval. For
SYNTRAN, it is a count of CRC-9 errors occurring in the accumulation
interval.
C-bit Errored
Seconds (CES)
An CES is a second with one or more CCVs OR one or more Out of
Frame defects OR a detected incoming AIS. This count is only for the
SYNTRAN and C-bit Parity DS3 applications. This gauge is not
incremented when UASs are counted.
C-bit Severely
Errored
Seconds (CSES)
A CSES is a second with 44 or more CCVs OR one or more Out of Frame
defects OR a detected incoming AIS. This count is only for the
SYNTRAN and C-bit Parity DS3 applications. This gauge is not
incremented when UAS are counted.
CDPD
Cellular Digital Packet Data. A radio technology that supports the
transmission of packet data to speeds of up to 19.2 Kbps over the existing
analog AMPS (Advanced Mobile Phone Service) cellular network, with
appropriate CDPD upgrades.
Central Office
(CO)
Where telephone companies terminate customer lines and locate
switching equipment to interconnect those lines with other networks.
Challenge
Handshake
Authorization
Protocol
(CHAP)
A strong authentication method used with PPP for user login. A type of
authentication in which the authentication agent (typically a network
server) sends the client program a key to be used to encrypt the username
and password. This enables the username and password to be transmitted
in an encrypted form to protect them against eavesdroppers. When using
CHAP, the username/password is sent encrypted over the connection,
preventing sniffing. See also PAP.
Glossary - 4
Axxius 800 - Release 2.2
Glossary
channel
channel
A generic term for a communications path on a given medium;
multiplexing techniques allow providers to put multiple channels over a
single medium.
Channel
Associated
Signaling (CAS)
A form of circuit state signaling in which the circuit state is indicated by
one or more bits of signaling status sent repetitively and associated with
that specific circuit.
CIDR
Classless Inter-Domain Routing. CIDR is a new addressing scheme for
the Internet which allows for more efficient allocation of IP addresses
than the old Class A, B, and C address scheme.
Circuit
Identifier
This is a character string specified by the circuit vendor, and is useful
when communicating with the vendor during the troubleshooting
process.
Clear Channel
A digital circuit where no framing or control bits (i.e. for signaling) are
required, thus making the full bandwidth available for communications.
For example, a 56 Kbps circuit is typically a 64 Kbps digital circuit with
8 Kbps used for signaling. Sometimes called Switched-56.
CLI
Command Line Interface
Classless
Routing
See CIDR
cold-standby
In a redundant DS3 controller setup, the standby controller can be in two
states, the hot-standby signifies that the card is ready to go active
(healthy) but for some reason (code of the 2 controllers is not the
same) it will need to reconfigure the box when it goes active,
which will be service affecting. Also see hot-standby.
Command Line
The command line is where you enter MS-DOS commands.
Community
Name
String that defines an administrative relationship between SNMP
entities.
Axxius 800 - Release 2.2
Glossary - 5
Glossary
Constant Bit Rate (CBR)
Constant Bit
Rate (CBR)
Refers to the transmission properties that data, video and voice uphold
when traversing a transport medium. Information traveling at a constant
bit rate means there is no fluctuation in signal integrity.
CSU
Channel Service Unit, the interface to the T1 line that terminates the local
loop.
Customer
Premise
Equipment
(CPE)
On digital circuits provided by the telephone company, any terminating
hardware owned by the user and not by the Telco (telephone company)
is generically referred to as CPE.
Cyclic
Redundancy
Check (CRC)
A check sum indicator based on the remainder of a polynomial
calculation performed on the transmitted data that is used to verify, with
some fixed probability of correctness, whether that data was transmitted.
D4 Superframe
(SF)
D4 Superframe (SF) Framing Format. The most popular framing format
in the T1 environment. Its name stems from the way framing is
performed in the D-series of channel banks from AT&T. There are 12
separate 193-bit frames in a superframe. The D4 framing bit is used to
identify both the channel and the signaling frame. In D4 framing,
signaling for voice channels is carried in-band by every channel along
with the encoded voice. “Robbed bit signaling” is a technique used in D4
channel banks to convey signaling information. With this technique, the
eighth bit (least significant bit) of each of the 24 8-bit timeslots is
“robbed” every sixth frame to convey voice related signaling information
(on-hook, off-hook, etc.) for each voice channel.
Data Terminal
Equipment
(DTE)
Data Terminal Equipment refers to communications hardware such as
computers, terminals, and similar equipment, as opposed to DCE such as
modems.
DDS
Digital Data System. DDS is a private line digital service, typically with
data rates at 2400, 4800, 9600 and 56000 bits per second.
Glossary - 6
Axxius 800 - Release 2.2
Glossary
DHCP
DHCP
Dynamic Host Configuration Protocol. DHCP is a network configuration
that allows maintenance to be performed from a central site rather than
by end users.
download
To transfer data from a larger "host" system to a smaller "client" system’s
hard drive or other local storage device.
Drop & Insert
(D&I)
As applied to T1, D&I refers to the process whereby one DS0 channel is
demultiplexed out of the DS1 synchronous bit stream at one port of a
digital channel back and another DS0 inserted back in.
DS0
Digital Signal Zero, the standard bandwidth for digitized voice channels.
DS1
Digital Signal Level 1. A digital signal transmitted at a nominal rate of
1.544 Mbps.
DS3
Digital Signal Level 3. A digital signal transmitted at a nominal rate of
44.736 Mbps.
DSU/CSU
Data Service Unit/Channel Service Unit. A device terminating a digital
channel on a customer’s premises where it performs line coding, line
conditioning and equalization functions while responding to the receipt
of loopback codes sent from the Central Office (CO) A DSU/CSU sits
between the digital line coming in from the CO and devices such as
channel banks or data communications devices.
Dual Tone
MultiFrequency
(DTMF)
Dual Tone Multi-Frequency is the system used by touch-tone telephones.
DTMF assigns a specific sound frequency, or tone, to each key so that it
can easily be identified by a monitoring microprocessor. That frequency
is then translated into a usable analog or digital signal. This is commonly
known as Touch Tone.
Dynamic Host
Configuration
Protocol
(DHCP)
A network configuration that allows maintenance to be performed from
a central site rather than by end users.
Axxius 800 - Release 2.2
Glossary - 7
Glossary
E&M Signaling
E&M Signaling
A signaling arrangement that uses separate leads, called respectively the
E lead and the M lead, for the signaling and voice signals. The M lead
(derived from ‘Mouth’) transmits ground or battery to the distant end of
the circuit, while incoming signals are received as either a grounded or
open condition on the E (derived from ‘Ear’) lead. The E&M tie trunk
interface functions as a de facto standard in the PBX - T1 multiplexer
Telco environment.
Earth ground
A wire conductor that terminates in the earth for electrical purposes. It is
generally the negative side of the circuit and is most important in
alternating current (AC) circuits. Chassis Ground is the general term
used in direct current (DC) circuits.
Electromagnetic
Interference
(EMI)
Equipment used in high speed data systems, including ATM, that
generate and transmit many signals in the radio frequency portion of the
electromagnetic spectrum. Interference to other equipment or radio
services may result if sufficient power from these signals escape the
equipment enclosures or transmission media. National and international
regulatory agencies (FCC, CISPR, etc.) set limits for these emissions.
Class A is for industrial use and Class B is for residential use.
Ethernet
Ethernet is a particular network topology and protocol, especially useful
in LANs. It comes in various speeds and is often regarded as THE current
technology for general network direct connection. The current
connectivity is generally considered to be 10Base-T or 100Base-T, while
the backbone, if one is used, is coaxial cable or Fiber optics. There is also
a 1000Base-T for certain specialty copper joining situations.
Facilities Data
Link (FDL)
FDL supports the communication of various network information in the
form of in-service monitoring and diagnostics.
File Transfer
Protocol (FTP)
An Internet protocol that enables you to transfer files between computers
on the Internet.
filter
An operating parameter used with routers that can be set to block the
transfer of packets from one LAN to another.
Glossary - 8
Axxius 800 - Release 2.2
Glossary
frame
frame
A fragment of data that is packaged into a frame format, which comprises
a header, payload, and trailer.
frame relay
A packet-switching protocol for connecting devices on a Wide Area
Network (WAN). Frame Relay networks in the U.S. support data transfer
rates at T1 (1.544 Mbps) and T3 (45 Mbps) speeds. Most telephone
companies now provide Frame Relay service for customers who want
connections at 56 Kbps to T1 speeds. However, it is being replaced in
some areas by faster technologies, such as ATM.
FX
Foreign Exchange. A Central Office trunk which has access to a distant
central office. Dial Tone is returned from that distant Central Office, and
a location can be reached in the area of the foreign Central Office by
dialing a local number. This will provide easier access for customers in
that area and calls may be made anywhere in the foreign exchange area
for a flat rate.
FXO
Foreign Exchange Office. Foreign exchange (FX) service is a service
that can be ordered from the telephone company that provides local
telephone service from a central office which is outside (foreign to) the
subscriber’s exchange area. Simply, a user can pick up the phone in one
city and receive a dial tone in the foreign city. This kind of connection is
provided by a type of trunk called foreign exchange (FX) trunk. FX trunk
signaling can be provided over analog or T1 links. Connecting POTS
telephones to a computer telephony system via T1 links requires a
channel bank configured with FX type connections.
FXS
Foreign Exchange Station.
gateway
A link from one computer system to a different computer system.
ground
A physical connection to the earth or other reference point.
ground start
(GS)
A method of signaling from a terminal or subscriber loop to a switch, in
which method one side of a cable pair is temporarily grounded
Axxius 800 - Release 2.2
Glossary - 9
Glossary
GUI
GUI
Graphical User Interface, pronounced "GOOEY". A set of screen
presentations and metaphors that utilize graphic elements such as icons
in an attempt to make an operating system easier to use.
High Density
Bipolar 3
(HDB3)
A bipolar coding method that does not allow more than 3 consecutive
zeros.
High level Data
Link Control
(HDLC)
The HDLC protocol secures information in a data frame that allows
devices to control data flow and correct errors. For any HDLC
communications session, one station is designated primary and the other
secondary.
hop
Each individual short trip that packets make from router to router, as they
are routed to their destination is a Hop.
host
A computer that allows users to communicate with other host computers
on a network.
hot-standby
In a redundant DS3 controller setup, the standby controller can be in two
states, the hot-standby signifies that the card is ready to take over for the
active and the switch will not affect service. Also see cold-standby.
hub
A common connection point for devices in a network. Hubs are
commonly used to connect segments of a LAN. A hub contains multiple
ports.
IP
Internet Protocol
Integrated
Services Digital
Network
(ISDN)
A technology offered by telephone carriers that allows for the rapid
transfer of voice and data. ISDN supports data transfer rates of 64 Kbps
(64,000 bits per second). Most ISDN lines offered by telephone
companies give you two lines at once, called B channels. You can use
one line for voice and the other for data, or you can use both lines for data
to give you data rates of 128 Kbps, slightly more than 2 times the data
rate provided by today’s fastest modems.
Glossary - 10
Axxius 800 - Release 2.2
Glossary
ISDN BRI
ISDN BRI
Integrated Services Digital Network. BRI, which is 144,000 bits per
second and designed for the desktop.
internet
"A network of networks," the Internet supports FTP, WWW, Gopher,
E-Mail, Telnet, and many other world-wide information transfer
protocols and services. ISPs provide an effective interface with the
Internet. The Internet itself is made up of thousands of LANs and WANs,
all using TCP/IP to provide information services to millions of users. A
worldwide network of networks that all use the TCP/IP communications
protocol and share a common address space.
Internet
Protocol (IP)
Internet Protocol, the method by which most Internet activity takes place.
Members with access to TCP/IP through a SLIP or PPP connection can
connect to many ISP services in this manner. As the name implies, it is a
protocol for network activity. Most current networks support some sort
of TCP or IP directly or indirectly.
IP address
A string of four numbers separated by periods (such as 111.22.3.144)
used to represent a computer on the Internet. The format of the address is
specified by the Internet Protocol in RFC 791. Each of the four number
must be 255 or less; they may be 0.
jitter
Interference on an analog line caused by a variation of a signal from its
reference timing slots. Jitter can cause problems in the receipt of data and
any subsequent processing of that data.
kbps
A transmission speed. Kilobits (thousands of bits) per second.
kilobyte (kb)
A representative word meaning one thousand bytes.
LAN (Local
Area Network)
A group of computers at a single location (usually an office or home) that
are connected by phone lines, network cables of various configurations
or coaxial cable. Usually controlled and administered by a system or
network administrator.
Axxius 800 - Release 2.2
Glossary - 11
Glossary
Line Coding Violation (LCV)
Line Coding
Violation
(LCV)
This parameter is a count of both BPVs and EXZs occurring over the
accumulation period. An EXZ increments the LCV by one regardless of
the length of the zero string.
Line Errored
Seconds (LES)
A Line Errored Second is a second in which one or more CVs occurred
OR one or more LOS defects.
Line Interface
Unit (LIU)
Typically, a controller device in a D-type channel bank, that incorporates
a controller, channel service unit (CSU), ringing generator and power
converter on a single card to interface between the T1 network and the
analog functions of the channel bank.
LLC
Logical Link Control. A protocol developed by the IEEE 802.2
committee for data-link-level transmission control
LMI
Local Management Interface. A specification for the use of frame-relay
products that define a method of exchanging status information between
devices such as routers.
LMU
Line Monitor Unit.
LOF
Loss of Frame.
LOS
Los of Signal.
loop back test
Any test in which a test signal is injected at one end of a circuit, is looped
back at the other end, and monitored at the originating end.
loop start (LS)
A method of demanding dial tone from the central office by completing
an electrical pathway between the outbound and return conductors of a
telephone line. Loop start is employed by single-line telephone
instruments, for example
loopback
A diagnostic test in which a signal is transmitted across a medium while
the sending device waits for its return.
Glossary - 12
Axxius 800 - Release 2.2
Glossary
LULT
LULT
Line Unit Line Termination
LUNT
Line Unit Network Termination
Management
Information
Base (MIB)
A data base of objects, with attributes and values, representing the
manageable components of a network device. Used in SNMP. There are
industry standardized MIBs and proprietary MIBs
Media Access
Control (MAC)
The lower of the two sub-layers of the data link layer defined by the
IEEE. The MAC sub-layer handles access to shared media, such as
whether token passing or contention will be used. The MAC contains the
standardized data link layer address that is required for every port or
device that connects to a LAN. Other devices in the network use these
addresses to locate specific ports in the network and to create and update
routing tables and data structures. MAC addresses are 6 bytes long and
are controlled by the IEEE.
Mean Time
Between
Failures
(MTBF)
This was an effort to establish a figure that gives an estimate of the
reliability of a piece of equipment. The higher the MTBF rating, the
longer the equipment should last.
megabyte (MB)
A measurement of storage capacity equal to approximately 1 million
bytes (1,048,576 bytes).
modem
MOdulator-DEModulator, a device that takes digital computer signal,
converts it to analog, and sends it across the phone line. Another modem
on the reverse does the exact opposite action. Modems transfer data at
different speeds or rates, called baud.
multiplexor
A complex piece of telephone equipment which combines the data
stream of several leased lines for transmission over a single higher
bandwidth leased line. Multiplexors are used in the construction of
WANs.
network
A set of computers linked to one another for data sharing, or the link
itself.
Axxius 800 - Release 2.2
Glossary - 13
Glossary
Network Address Translation (NAT)
Network
Address
Translation
(NAT)
An Internet standard that enables a local-area network (LAN) to use one
set of IP addresses for internal traffic and a second set of addresses for
external traffic. A NAT box located where the LAN meets the Internet
makes all necessary IP address translations.
OOS
Out of Service.
OCU-DP
Office Channel Unit, Data Port. A channel bank unit used to interface
between the channel bank and a customer’s DDS, DSU or DSU.
P-bit Coding
Violation (PCV)
For all DS3 applications, a coding violation error event is a P-bit Parity
Error event. A P-bit Parity Error event is the occurrence of a received Pbit code on the DS3 M-frame that is not identical to the corresponding
locally-calculated code.
P-bit Errored
Seconds (PES)
A PES is a second with one or more PCVs OR one or more Out of Frame
defects OR a detected incoming AIS. This gauge is not incremented
when UASs are counted.
P-bit Severely
Errored
Seconds (PSES)
A PSES is a second with 44 or more PCVs OR one or more Out of Frame
defects OR a detected incoming AIS. This gauge is not incremented
when UASs are counted.
packet
A unit of data sent across a network. When a large block of data is to be
sent over a network, it is broken up into several packets, sent, and the
reassembled at the other end. The exact layout of an individual packet is
determined by the protocol and network architecture being used.
Packet InterNet
Grouper
(PING)
PING is a program used to test whether a particular network destination
on the Internet is online (i.e. working) by repeatedly bouncing a "signal"
off a specified address and seeing how long that signal takes to complete
the round trip. No return signal - site is down or unreachable. Portion is
returned - trouble with the connection.
Glossary - 14
Axxius 800 - Release 2.2
Glossary
Password Authentication Protocol (PAP)
Password
Authentication
Protocol (PAP)
An authentication protocol that allows Point-to-Point Protocol peers to
authenticate one another.
Peak Cell Rate
(PCR)
The Peak Cell Rate, in cells/sec, is the cell rate which the source may
never exceed.
PLAR
Private Line, Automatic Ringdown. A leased voice circuit that connects
two single instruments together. When either handset is lifted, the other
instrument automatically rings.
PMDL
Path Maintenance Data Link.
Point-to-Point
Protocol (PPP)
Provides a standard means of encapsulating data packets sent over a
single-channel WAN link. It is the standard WAN encapsulation
protocol for the interoperability of bridges and routers.
port
A physical address that is associated with a physical connecting device.
protocol
Procedure or set of rules.
PVC
Permanent Virtual Circuit. A PVC is a permanent channel connection
between two ATM devices. PVC’s allow network transmissions to be
started without having to first establish a connection with the end point
ATM device. When a PVC is constructed, the end points of the
connection will agree upon a path in which data will travel, and therefore
agree upon the route that data will travel to reach its destination.
RIP
Routing Information Protocol. RIP is based on distance vector
algorithms that measure the shortest path between two points on a
network, based on the addresses of the originating and destination
devices. The shortest path is determined by the number of "hops"
between those points. Each router maintains a routing table, or routing
database, of known addresses and routes; each router periodically
broadcasts the contents of its table to neighboring routers in order that the
entire network can maintain a synchronized database.
Axxius 800 - Release 2.2
Glossary - 15
Glossary
robbed bit
robbed bit
A type of analog signaling that will occasionally steal information bits
used for circuit signaling coding.
router
A computer or internet working device that directs traffic and moves
packets between networks. A hardware architecture used in LANs,
MANs, WANs, the Internet and Intranets. A device that connects any
number of LANs. Routers use headers and a forwarding table to
determine where packets go, and they use ICMP to communicate with
each other and configure the best route between any two hosts.
signal
A generated electrical impulse that is a change in voltage to trigger an
event.
Simple Network
Management
Protocol
(SNMP)
SNMP is the most common method by which network managements
applications can query a management agent using a supported MIB
(Management Information Base). SNMP operates at the OSI application
layer.
slot
As it applies to the Adit 600 is the position in the chassis for the
controller, power supply or a service card (A, power or 1-6 for service
cads).
As it applies to the Axxius 800 is the position in the chassis for the
controller, power supply or a service card (A1, A2, P1, P2 or 1-8 for
service cards).
span
A span is a logical name for an access port into the Access Bank
II. A span carries Voice/Data information to/from the Access
Bank.
Spanning Tree
Spanning Tree Protocol is a link management protocol that provides path
redundancy while preventing undesirable loops in the network. For an
Ethernet network to function properly, only one active path can exist
between two stations.
Glossary - 16
Axxius 800 - Release 2.2
Glossary
star network
star network
A star is a network topology that connects all devices to a central location
called a hub. Traditional star networks are designed to be easily
expandable because hubs can be connected to additional hubs of other
networks. A star is the opposite of a ring network. Also see BUS
network.
static
In communications, interference (static) that destroys the integrity of
signals on a line. Noise can come from a variety of sources, including
radio waves, nearby electrical wires, lightning, and bad connections. One
of the major advantages of fiber optic cables over metal cables is that
they are much less susceptible to noise.
subnet mask
32-bit quantity indicating which bits in an IP address identify the
physical network
subrate
multiplexing
The process of combining lower data rates into a single 64 Kbps channel
signal.
subscriber line
The telephone line connecting the local Telco CO to the customer’s
telephone instrument or telephone system.
switch
In networks, a device that filters and forwards packets between LAN
segments. Switches operate at the data link layer (layer 2) of the OSI
Reference Model and therefore support any packet protocol. LANs that
use switches to join segments are called switched LANs or, in the case of
Ethernet networks, switched Ethernet LANs. See contact.
synchronous
See asynchronous as an opposing technology. Data transmission using
synchronization bytes, instead of start/stop bits, to control the
transmission. In xDSL, video streams are considered to be synchronous
in nature.
T1
Trunk Level 1. A digital transmission link with a total signaling speed of
1.544 Mbps. T1 is a standard for the digital transmission in North
America
Axxius 800 - Release 2.2
Glossary - 17
Glossary
TBOS
TBOS
Telemetry Byte Oriented Serial. TBOS is an alarm monitoring and
control prototype for telephone network equipment.
telnet
An Internet standard protocol that enables a computer to function as a
terminal working from a remote computer.
TFTP
Trivial File Transfer Protocol.
Time Division
Multiplexing
(TDM)
TDM systems offer a synchronous transmission of data over a fixed
bandwidth channel. The most popular TDM transports are a T1 (1.5
Mbps) transport and a T3 (45 Mbps) transport. This transmission
medium is ideal for traffic requiring a CBR transport, such as voice.
traffic
The load of packets carried by a network or portion of a network. Heavy
traffic slows down the response time of the individual packets.
Transmission
Only (TO)
An operating mode on a 4-wire E&M card that provides dedicated oneway transmission paths to radio and modem equipment uncorrupted by
the insertion of A/B robbed bit signaling.
trap
A mechanism permitting a device to automatically send an alarm for
certain network events to a management station.
Trivial File
Protocol
(TFTP)
Trivial File Transfer Protocol. A simplified version of FTP that transfers
files but does not provide password protection or user-directory
capability.
trunk
A telephone communication path or channel between two points, one
usually being a Central Office (CO).
trunk port
An input on a PABX or KSU that is used to interface the system with CO
lines.
upload
To send a file from one computer to another via modem or other
telecommunication method. Uploading is usually accomplished by FTP
technology.
Glossary - 18
Axxius 800 - Release 2.2
Glossary
V.90
V.90
The standard for full-duplex modems sending and receiving data across
phone lines at up to 56,600 bps, approved by the International
Telecommunication Union (ITU) in February, 1998.
VC MUX
Virtual Channel Multiplexer.
Voice Over IP
(VoIP)
An emerging technology that is, voice delivered using the Internet
Protocol, is a term used in IP telephony for a set of facilities for managing
the delivery of voice information using the Internet Protocol (IP). In
general, this means sending voice information in digital form in discrete
packets rather than in the traditional circuit committed protocols of the
public switched telephone network (PSTN). A major advantage of VOIP
and Internet telephony is that it avoids the tolls charged by ordinary
telephone service.
Wide Area
Network
(WAN)
A private long distance network that uses leased lines to connect
computers or LANs. A wide area network is a linking of computers not
physically attached through conventional network connectivity. Usually
the WAN connection is a dedicated or high grade dial up phone link. It
is often done with T1 or T3 connections but can also be through satellite
or other technologies.
Wink
A signal sent between two telecommunications devices as part of a
handshaking protocol. It is a momentary interruption in SF (Single
Frequency) tone, indicating that the distant Central Office (CO) is ready
to receive the digits that have just been dialed. In telephone switching
systems, a single supervisory pulse.
Axxius 800 - Release 2.2
Glossary - 19
Glossary
Glossary - 20
Axxius 800 - Release 2.2
INDEX
Numerics
Index
10/100Base-T Ethernet Connector . . . . . . . . 1-13
10Base-T . . . . . . . . . . . . . . . . . . . . . .Glossary-1
26-pin micro-SCSI
V.35 card . . . . . . . . . . . . . . . . . . . . . . . . . 16-7
V.35/V.54 cards . . . . . . . . . . . . . . . . . . . . 16-6
3-DSO BRITE mode . . . . . . . . . . . . . . . . . . . 9-2
A
ACO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17
aco (alarm Cut Off) command . . . . . . . . . . . . 5-5
add
(ds1)
ais command . . . . . . . . . . . . . . . . . . . . . 5-7
(router)
dhcp server option command . . . . . . . . 5-8
dns proxy command . . . . . . 5-7, 5-9, 5-43
remote command . . . . . . . . . . . . . . . . . . 5-9
snmp community command . . . . . . . . 5-10
snmp trap command . . . . . . . . . . . . . . 5-11
static dns host command . . . . . . . . . . . 5-12
uploaduser command . . . . . . . . . . . . . . 5-13
(router-lan)
filter
address command . . . . . . . . . . . . . . 5-14
custom command . . . . . . . . . . . . . . 5-15
protocol command . . . . . . . . . . . . . . 5-17
secondary ip address command . . . . . . 5-18
static
ip address command . . . . . . . . . . . . 5-19
ip network command . . . . . . . . . . . . 5-20
ipx network command . . . . . . . . . . 5-21
mac address command . . . . . . . . . . 5-22
(router-wan)
firewall command . . . . . . . . . . . . . . . . 5-23
gre network command . . . . . . . . . . . . . 5-26
nat bypass command . . . . . . . . . . . . . . 5-27
static
ip address command . . . . . . . . . . . . 5-28
ip network command . . . . . . . . . . . 5-29
ipx network command . . . . . . . . . . 5-30
mac address command . . . . . . . . . . 5-31
nat address command . . . . . . . . . . . 5-32
command . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
user command . . . . . . . . . . . . . . . . . . . . . 5-32
ADPCM mapping . . . . . . . . . . . . . . . . . . . . 5-82
Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-2
clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-4
display . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-4
identify . . . . . . . . . . . . . . . . . . . . . . . . . . .C-2
indicators . . . . . . . . . . . . . . . . . . . . . . . . . .C-2
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-2
alarm connector . . . . . . . . . . . . . . . . . . 3-9, 3-10
Alarm LEDs . . . . . . . . . . . . . . . . . . . . . . . . . 1-15
alarms command . . . . . . . . . . . . . . . . . . . . . 5-33
alert alarm . . . . . . . . . . . . . . . . . . . . . 5-33, 5-62
Analog . . . . . . . . . . . . . . . . . . . . . . . . Glossary-1
Annex D . . . . . . . . . . . . . . . . . . . . . . . Glossary-1
autologout . . . . . . . . . . . . . . . . . . . . . . . . . 5-102
B
B8ZS . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-2
Index
C
Base Platform . . . . . . . . . . . . . . . . . . . . . . . . 1-1
ACO . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17
Card Removal Handles 1-10, 6-10, 7-12, 11-5
Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Control Panel Interfaces . . . . . . . . . . . . . 1-11
Local and Remote Management . . . . . . . 1-10
Management Ports . . . . . . . . . . . . . . . . . 1-10
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
basic CLI system setup . . . . . . . . . . . . . . . . . 4-4
Basics, SNMP . . . . . . . . . . . . . . . . . . . . . . . . B-2
baud rate . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-97
BER . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-2
BERT . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-2
bipolar . . . . . . . . . . . . . . . . . . . . . . . . Glossary-3
Bipolar 8 Zero Substitution . . . . . . . . Glossary-2
bipolar violation . . . . . . . . . . . . . . . . Glossary-3
Bit . . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-3
Bits Clock connection . . . . . . . . . . . . . . . . . 3-11
bps . . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-3
BPV . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-3
BRI . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-3
C
cable
V.35 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-7
cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
ferrite beads . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Card Removal Handles . .1-10, 6-10, 7-12, 11-5
CAS . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-5
Channel Associated Signaling . . . . . . . . . . . 5-40
FXO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
chassis dimensions . . . . . . . . . . . . . . . . . . . . 1-8
Chassis Ground Connector . . . . . . . . . . . . . . 3-6
CIDR . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-5
Classless Routing . . . . . . . . . . . . . . . Glossary-5
clear
(ocudp) performance command . . . . . . . 5-37
(router)
Index - 2
performance command . . . . . . . . . . . . 5-39
(router) ip address table command . . . . . 5-38
(router) mac address table command . . . 5-38
alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4
command . . . . . . . . . . . . . . . . . . . . . . . . 5-34
ds1 command . . . . . . . . . . . . . . . . . . . . . 5-35
ds3 command . . . . . . . . . . . . . . . . . . . . . 5-36
key command . . . . . . . . . . . . . . . . . . . . . 5-37
log command . . . . . . . . . . . . . . . . . . . . . 5-37
clear channel . . . . . . . . . . . . . . . . . . . Glossary-5
CLI (Command Line Interface) 1-10, Glossary-5
CLI commands
aco (Alarm Cut Off) . . . . . . . . . . . . . . . . . 5-5
add . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
(ds1)
ais . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
(router)
dhcp server option . . . . . . . . . . . . . . 5-8
dns proxy . . . . . . . . . . . . .5-7, 5-9, 5-43
remote . . . . . . . . . . . . . . . . . . . . . . . 5-9
snmp community . . . . . . . . . . . . . . 5-10
snmp trap . . . . . . . . . . . . . . . . . . . . 5-11
static dns host . . . . . . . . . . . . . . . . . 5-12
uploaduser . . . . . . . . . . . . . . . . . . . 5-13
(router-lan)
filter address . . . . . . . . . . . . . . . . . . 5-14
filter custom . . . . . . . . . . . . . . . . . . 5-15
filter protocol . . . . . . . . . . . . . . . . . 5-17
secondary ip address . . . . . . . . . . . 5-18
static ip address . . . . . . . . . . . . . . . 5-19
static ip network . . . . . . . . . . . . . . . 5-20
static ipx network . . . . . . . . . . . . . . 5-21
static mac address . . . . . . . . . . . . . 5-22
(router-wan)
firewall . . . . . . . . . . . . . . . . . . . . . . 5-23
gre network . . . . . . . . . . . . . . . . . . 5-26
nat bypass . . . . . . . . . . . . . . . . . . . . 5-27
static ip address . . . . . . . . . . . . . . . 5-28
static ip network . . . . . . . . . . . . . . . 5-29
Axxius 800 - Release 2.2
Index
C
static ipx network . . . . . . . . . . . . . . 5-30
static mac address . . . . . . . . . . . . . . 5-31
static nat address . . . . . . . . . . . . . . . 5-32
user . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-32
alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-33
clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-34
(ocudp) performance . . . . . . . . . . . . . . 5-37
(router)
performance . . . . . . . . . . . . . . . . . . . 5-39
(router) ip address table . . . . . . . . . . . . 5-38
(router) mac address table . . . . . . . . . . 5-38
ds1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-35
ds3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-36
key . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-37
log . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-37
connect . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-40
(router-trunk) (t1) . . . . . . . . . . . . . . . . 5-41
delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-42
(ds1)
ais . . . . . . . . . . . . . . . . . . . . . . . . . . 5-43
(router)
dhcp server option . . . . . . . . . . . . . . 5-44
dns proxy . . . . . . . . . . . . . . . . . . . . . 5-44
remote . . . . . . . . . . . . . . . . . . . . . . . 5-45
snmp community . . . . . . . . . . . . . . . 5-45
snmp trap . . . . . . . . . . . . . . . . . . . . . 5-46
static dns host . . . . . . . . . . . . . . . . . 5-46
uploaduser . . . . . . . . . . . . . . . . . . . . 5-47
(router-lan)
filter . . . . . . . . . . . . . . . . . . . . . . . . . 5-48
secondary ip address . . . . . . . . . . . . 5-49
static ip address . . . . . . . . . . . . . . . . 5-50
static ip network . . . . . . . . . . . . . . . 5-51
static ipx network . . . . . . . . . . . . . . 5-52
static mac address . . . . . . . . . . . . . . 5-53
(router-wan)
firewall . . . . . . . . . . . . . . . . . . . . . . 5-53
gre network . . . . . . . . . . . . . . . . . . . 5-54
nat bypass . . . . . . . . . . . . . . . . . . . . 5-54
Axxius 800 - Release 2.2
static ip address . . . . . . . . . . . . . . . . 5-55
static ip network . . . . . . . . . . . . . . . 5-56
static ipx network . . . . . . . . . . . . . . 5-56
static mac address . . . . . . . . . . . . . . 5-57
static nat address . . . . . . . . . . . . . . . 5-57
user . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-58
disconnect . . . . . . . . . . . . . . . . . . . . . . . . 5-58
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-59
install (slot) router . . . . . . . . . . . . . . . . . . 5-59
load
tftp . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-60
xmodem . . . . . . . . . . . . . . . . . . . . . . . . 5-61
log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-62
ntp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-191
ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-63
print
config . . . . . . . . . . . . . . . . . . . . . . . . . 5-64
help . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-65
rename (router) . . . . . . . . . . . . . . . . . . . . 5-65
reset
(controller) . . . . . . . . . . . . . . . . . . . . . 5-66
(router) . . . . . . . . . . . . . . . . . . . . . . . . 5-66
(router) coldboot . . . . . . . . . . . . . . . . . 5-67
restore defaults . . . . . . . . . . . . . . . . . . . . 5-67
rtrping . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-68
set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-69
(bri) . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-72
mode . . . . . . . . . . . . . . . . . . . . . . . . 5-73
pmsync . . . . . . . . . . . . . . . . . . . . . . 5-73
(ds0) . . . . . . . . . . . . . . . . . . . . . . . . . . 5-76
signal . . . . . . . . . . . . . . . . . . . . . . . . 5-76
type . . . . . . . . . . . . . . . . . . . . . . . . . 5-77
(ds1 card) . . . . . . . . . . . . . . . . . . . . . . 5-81
adpcm map . . . . . . . . . . . . . . . . . . . 5-82
t1/e1 spantype . . . . . . . . . . . . . . . . . 5-81
(ds1) . . . . . . . . . . . . . . . . . . . . . . . . . . 5-78
(ds3) . . . . . . . . . . . . . . . . . . . . . . . . . . 5-83
clock . . . . . . . . . . . . . . . . . . . . . . . . 5-83
(ds3) clock . . . . . . . . . . . . . . . . . . . . . . 5-83
Index - 3
Index
C
(fxo) . . . . . . . . . . . . . . . . . . . . . . . . . . 5-87
(fxsPS) . . . . . . . . . . . . . . . . . . . . . . . . 5-88
(ocudp)
baud . . . . . . . . . . . . . . . . . . . . . . . . 5-97
loopback . . . . . . . . . . . . . . . . . . . . . 5-98
loopdetect . . . . . . . . . . . . . . . . . . . . 5-99
mvec . . . . . . . . . . . . . . . . . . . . . . . 5-100
secondary . . . . . . . . . . . . . . . . . . . 5-100
selftest . . . . . . . . . . . . . . . . . . . . . . 5-101
up/down . . . . . . . . . . . . . . . . . . . . 5-101
(router)
autologout . . . . . . . . . . . . . . . . . . . 5-102
default . . . . . . . . . . . . . . . . . . . . . . 5-102
dhcp . . . . . . . . . . . . . . . . . . . . . . . 5-103
disable . . . . . . . . . . . . . . . . . . . 5-103
relay server . . . . . . . . . . . . . . . . 5-103
server dnsserver . . . . . . . . . . . . 5-104
server domain . . . . . . . . . . . . . . 5-104
server duration . . . . . . . . . . . . . 5-105
server netbios nameserver . . . . 5-105
server netbios nodetype . . . . . . 5-106
server netbios scope . . . . . . . . . 5-106
server startaddr . . . . . . . . . . . . . 5-107
dns . . . . . . . . . . . . . . . . . . . . . . . . 5-108
domain . . . . . . . . . . . . . . . . . . . 5-108
name . . . . . . . . . . . . . . . . . . . . . 5-108
resolver . . . . . . . . . . . . . . . . . . . 5-109
server . . . . . . . . . . . . . . . . . . . . 5-109
enhanced security . . . . . . . . . . . . . 5-110
lmi . . . . . . . . . . . . . . . . . . . . . . . . . 5-110
poll . . . . . . . . . . . . . . . . . . . . . . 5-111
login
auth . . . . . . . . . . . . . . . . . . . . . . 5-111
prompt . . . . . . . . . . . . . . . . . . . 5-112
ntp . . . . . . . . . . . . . . . . . . . . . . . . . 5-112
enable/disable . . . . . . . . . . . . . . 5-112
poll . . . . . . . . . . . . . . . . . . . . . . 5-113
server . . . . . . . . . . . . . . . . . . . . 5-113
timezone . . . . . . . . . . . . . . . . . . 5-114
Index - 4
password . . . . . . . . . . . . . . . . . . .
port . . . . . . . . . . . . . . . . . . . . . . . .
baudrate . . . . . . . . . . . . . . . . . .
databits . . . . . . . . . . . . . . . . . . .
dsr low reset . . . . . . . . . . . . . . .
flowcontrol . . . . . . . . . . . . . . .
inactivity timer . . . . . . . . . . . . .
ip . . . . . . . . . . . . . . . . . . . . . . .
name . . . . . . . . . . . . . . . . . . . .
parity . . . . . . . . . . . . . . . . . . . .
passive . . . . . . . . . . . . . . . . . . .
password . . . . . . . . . . . . . . . . .
prompt . . . . . . . . . . . . . . . . . . .
protocolport . . . . . . . . . . . . . . .
stopbits . . . . . . . . . . . . . . . . . . .
tbos map description . . . . . . . .
tbos map display . . . . . . . . . . .
type . . . . . . . . . . . . . . . . . . . . .
ppp auth . . . . . . . . . . . . . . . . . . . .
byremote protocol . . . . . . . . . .
byremote secret . . . . . . . . . . . .
byremote user . . . . . . . . . . . . .
ofremote protocol . . . . . . . . . .
ppp security . . . . . . . . . . . . . . . . .
address . . . . . . . . . . . . . . . . . . .
password . . . . . . . . . . . . . . . . .
server . . . . . . . . . . . . . . . . . . . .
proxy . . . . . . . . . . . . . . . . . . . . . .
reboot . . . . . . . . . . . . . . . . . . . . . .
rip . . . . . . . . . . . . . . . . . . . . . . . . .
snmp . . . . . . . . . . . . . . . . . . . . . . .
contact . . . . . . . . . . . . . . . . . . .
location . . . . . . . . . . . . . . . . . .
name . . . . . . . . . . . . . . . . . . . .
stp . . . . . . . . . . . . . . . . . . . . . . . . .
bridge forwarddelay . . . . . . . . .
bridge hellotime . . . . . . . . . . . .
bridge maxage . . . . . . . . . . . . .
bridge priority . . . . . . . . . . . . .
5-114
5-115
5-115
5-116
5-116
5-117
5-118
5-118
5-119
5-119
5-120
5-120
5-121
5-121
5-122
5-122
5-123
5-124
5-125
5-125
5-125
5-126
5-126
5-127
5-127
5-127
5-128
5-129
5-131
5-131
5-132
5-132
5-132
5-133
5-134
5-134
5-134
5-135
5-135
Axxius 800 - Release 2.2
Index
C
enable/disable . . . . . . . . . . . . . . 5-136
syslog . . . . . . . . . . . . . . . . . . . . . . 5-137
enable/disable . . . . . . . . . . . . . . 5-137
facility . . . . . . . . . . . . . . . . . . . . 5-137
level . . . . . . . . . . . . . . . . . . . . . . 5-138
server . . . . . . . . . . . . . . . . . . . . . 5-138
(router-lan)
filter forward . . . . . . . . . . . . . . . . . 5-139
framing . . . . . . . . . . . . . . . . . . . . . 5-140
gateway . . . . . . . . . . . . . . . . . . . . . 5-141
ip address . . . . . . . . . . . . . . . . . . . . 5-142
ipx network . . . . . . . . . . . . . . . . . . 5-143
phy . . . . . . . . . . . . . . . . . . . . . . . . . 5-144
rip . . . . . . . . . . . . . . . . . . . . . . . . . 5-145
ip . . . . . . . . . . . . . . . . . . . . . . . . 5-145
ipx . . . . . . . . . . . . . . . . . . . . . . . 5-146
stp . . . . . . . . . . . . . . . . . . . . . . . . . 5-147
enable/disable . . . . . . . . . . . . . . 5-147
port cost . . . . . . . . . . . . . . . . . . . 5-148
port priority . . . . . . . . . . . . . . . . 5-148
up/down . . . . . . . . . . . . . . . . . . . . . 5-149
(router-trunk)
encapsulation . . . . . . . . . . . . . . . . . 5-150
multilink group . . . . . . . . . . . . . . . 5-150
up/down . . . . . . . . . . . . . . . . . . . . . 5-151
(router-trunk) speed . . . . . . . . . . . . . . 5-151
(router-wan)
dlci . . . . . . . . . . . . . . . . . . . . . . . . . 5-152
ip . . . . . . . . . . . . . . . . . . . . . . . . . . 5-155
ip address . . . . . . . . . . . . . . . . . . . . 5-155
ipx . . . . . . . . . . . . . . . . . . . . . . . . . 5-156
nat . . . . . . . . . . . . . . . . . . . . . . . . . 5-157
address . . . . . . . . . . . . . . . . . . . 5-157
enable/disable . . . . . . . . . . . . . . 5-158
ports . . . . . . . . . . . . . . . . . . . . . 5-158
other . . . . . . . . . . . . . . . . . . . . . . . . 5-159
ppp . . . . . . . . . . . . . . . . . . . . . . . . . 5-160
auth ofremote user . . . . . . . . . . 5-160
compression . . . . . . . . . . . . . . . 5-161
Axxius 800 - Release 2.2
security server . . . . . . . . . . . . . . 5-161
rip . . . . . . . . . . . . . . . . . . . . . . . . . 5-162
ip updates . . . . . . . . . . . . . . . . . 5-162
ipx updates . . . . . . . . . . . . . . . . 5-162
stp . . . . . . . . . . . . . . . . . . . . . . . . . 5-163
enable/disable . . . . . . . . . . . . . . 5-163
port cost . . . . . . . . . . . . . . . . . . 5-164
port priority . . . . . . . . . . . . . . . . 5-164
trunk . . . . . . . . . . . . . . . . . . . . . . . 5-165
up/down . . . . . . . . . . . . . . . . . . . . 5-165
(v35) . . . . . . . . . . . . . . . . . . . . . . . . . 5-170
(v54) . . . . . . . . . . . . . . . . . . . . . . . . . 5-172
alarms . . . . . . . . . . . . . . . . . . . . . . . . . 5-71
autoexit . . . . . . . . . . . . . . . . . . . . . . . . 5-71
cclabel . . . . . . . . . . . . . . . . . . . . . . . . . 5-74
clock . . . . . . . . . . . . . . . . . . . . . . . . . . 5-74
clock1 . . . . . . . . . . . . . . . . . . . . . . . . . 5-75
date . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-75
ethernet ip address . . . . . . . . . . . . . . . . 5-86
external alarms . . . . . . . . . . . . . . . . . . 5-86
id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-88
idle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-89
ip gateway . . . . . . . . . . . . . . . . . . . . . . 5-89
ipds0 . . . . . . . . . . . . . . . . . . . . . . . . . . 5-90
key . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-91
login
auth . . . . . . . . . . . . . . . . . . . . . . . . . 5-91
support . . . . . . . . . . . . . . . . . . . . . . 5-92
lsbackup . . . . . . . . . . . . . . . . . . . . . . . 5-92
lsprotect
enable/disable . . . . . . . . . . . . . . . . . 5-93
manual . . . . . . . . . . . . . . . . . . . . . . 5-93
nonrevertive . . . . . . . . . . . . . . . . . . 5-94
remove . . . . . . . . . . . . . . . . . . . . . . 5-95
revertive . . . . . . . . . . . . . . . . . . . . . 5-96
screen . . . . . . . . . . . . . . . . . . . . . . . . 5-166
snmp . . . . . . . . . . . . . . . . . . . . . . . . . 5-167
time . . . . . . . . . . . . . . . . . . . . . . . . . . 5-168
user . . . . . . . . . . . . . . . . . . . . . . . . . . 5-169
Index - 5
Index
C
level . . . . . . . . . . . . . . . . . . . . . . .
password . . . . . . . . . . . . . . . . . . . .
verification . . . . . . . . . . . . . . . . . . . .
show . . . . . . . . . . . . . . . . . . . . . . . . . . .
(bri) . . . . . . . . . . . . . . . . . . . . . . . . . .
(ds0) . . . . . . . . . . . . . . . . . . . . . . . . .
(ds1) . . . . . . . . . . . . . . . . . . . . . . . . .
(ds3) . . . . . . . . . . . . . . . . . . . . . . . . .
(fxo) . . . . . . . . . . . . . . . . . . . . . . . . .
(fxsPS) . . . . . . . . . . . . . . . . . . . . . . .
(ocudp) . . . . . . . . . . . . . . . . . . . . . . .
(router) . . . . . . . . . . . . . . . . . . . . . . .
dhcp . . . . . . . . . . . . . . . . . . . . . . .
dns . . . . . . . . . . . . . . . . . . . . . . . .
dns proxy . . . . . . . . . . . . . . . . . . .
lmi . . . . . . . . . . . . . . . . . . . . . . . . .
login . . . . . . . . . . . . . . . . . . . . . . .
ntp . . . . . . . . . . . . . . . . . . . . . . . . .
port . . . . . . . . . . . . . . . . . . . . . . . .
ppp . . . . . . . . . . . . . . . . . . . . . . . .
rip . . . . . . . . . . . . . . . . . . . . . . . . .
snmp . . . . . . . . . . . . . . . . . . . . . . .
stp . . . . . . . . . . . . . . . . . . . . . . . . .
syslog . . . . . . . . . . . . . . . . . . . . . .
uploaduser . . . . . . . . . . . . . . . . . .
(router-lan) . . . . . . . . . . . . . . . . . . . .
filter . . . . . . . . . . . . . . . . . . . . . . .
static . . . . . . . . . . . . . . . . . . . . . . .
ip address . . . . . . . . . . . . . . . . .
ip network . . . . . . . . . . . . . . . .
ipx network . . . . . . . . . . . . . . .
mac address . . . . . . . . . . . . . . .
stp . . . . . . . . . . . . . . . . . . . . . . . . .
(router-wan) . . . . . . . . . . . . . . . . . . .
firewall . . . . . . . . . . . . . . . . . . . . .
nat bypass . . . . . . . . . . . . . . . . . . .
ppp . . . . . . . . . . . . . . . . . . . . . . . .
static
ip address . . . . . . . . . . . . . . . . .
Index - 6
5-169
5-169
5-174
5-175
5-177
5-181
5-182
5-183
5-185
5-186
5-191
5-193
5-195
5-196
5-196
5-197
5-197
5-198
5-199
5-200
5-201
5-201
5-202
5-202
5-203
5-204
5-206
5-208
5-208
5-209
5-209
5-210
5-211
5-212
5-214
5-214
5-215
5-216
ip network . . . . . . . . . . . . . . . .
ipx network . . . . . . . . . . . . . . .
mac address . . . . . . . . . . . . . . .
static mac address . . . . . . . . . . . .
stp . . . . . . . . . . . . . . . . . . . . . . . . .
trunk . . . . . . . . . . . . . . . . . . . . . . .
(v35) . . . . . . . . . . . . . . . . . . . . . . . . .
(v54) . . . . . . . . . . . . . . . . . . . . . . . . .
adpcm . . . . . . . . . . . . . . . . . . . . . . . .
autoexit . . . . . . . . . . . . . . . . . . . . . . .
cclables . . . . . . . . . . . . . . . . . . . . . . .
clock . . . . . . . . . . . . . . . . . . . . . . . . .
connect . . . . . . . . . . . . . . . . . .5-178,
connect adpcm . . . . . . . . . . . . . . . . .
date . . . . . . . . . . . . . . . . . . . . . . . . . .
ethernet . . . . . . . . . . . . . . . . . . . . . . .
id . . . . . . . . . . . . . . . . . . . . . . . . . . . .
image . . . . . . . . . . . . . . . . . . . . . . . .
impedance . . . . . . . . . . . . . . . . . . . .
ip . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ipds0 . . . . . . . . . . . . . . . . . . . . . . . . .
login . . . . . . . . . . . . . . . . . . . . . . . . .
radius . . . . . . . . . . . . . . . . . . . . . . . .
screen . . . . . . . . . . . . . . . . . . . . . . . .
snmp . . . . . . . . . . . . . . . . . . . . . . . . .
syslog . . . . . . . . . . . . . . . . . . . . . . . .
time . . . . . . . . . . . . . . . . . . . . . . . . . .
users . . . . . . . . . . . . . . . . . . . . . . . . .
show external alarms . . . . . . . . . . . . . .
show lsprotect . . . . . . . . . . . . . . . . . . . .
status . . . . . . . . . . . . . . . . . . . . . . . . . . .
(adpcm) . . . . . . . . . . . . . . . . . . . . . .
performance . . . . . . . . . . . . . . . . .
performance history . . . . . . . . . . .
(bri) . . . . . . . . . . . . . . . . . . . . . . . . . .
performance . . . . . . . . . . . . . . . . .
performance history . . . . . . . . . . .
(ds0) . . . . . . . . . . . . . . . . . . . . . . . . .
(ds1) . . . . . . . . . . . . . . . . . . . . . . . . .
5-216
5-217
5-217
5-218
5-218
5-219
5-222
5-223
5-176
5-177
5-178
5-178
5-179
5-180
5-180
5-184
5-186
5-187
5-188
5-189
5-189
5-189
5-192
5-219
5-220
5-220
5-221
5-221
5-184
5-190
5-224
5-225
5-226
5-227
5-228
5-229
5-230
5-231
5-232
Axxius 800 - Release 2.2
Index
D
performance command . . . . . . . . . 5-233
performance history . . . . . . . . . . . 5-234
(ds3) . . . . . . . . . . . . . . . . . . . . . . . . . . 5-235
performance . . . . . . . . . . . . . . . . . . 5-236
performance history . . . . . . . . . . . 5-237
(fxo) . . . . . . . . . . . . . . . . . . . . . . . . . . 5-239
(fxsPS) . . . . . . . . . . . . . . . . . . . . . . . . 5-240
(fxsPSM) . . . . . . . . . . . . . . . . . . . . . . 5-240
(ocudp) . . . . . . . . . . . . . . . . . . . . . . . . 5-242
performance . . . . . . . . . . . . . . . . . . 5-243
performance history . . . . . . . . . . . 5-244
(router)
alarms . . . . . . . . . . . . . . . . . . . . . . 5-245
dns . . . . . . . . . . . . . . . . . . . . . . . . . 5-245
events . . . . . . . . . . . . . . . . . . . . . . . 5-246
ip address table . . . . . . . . . . . . . . . 5-247
ip network table . . . . . . . . . . . . . . . 5-248
ipx network table . . . . . . . . . . . . . . 5-249
ipx server table . . . . . . . . . . . . . . . 5-250
mac address table . . . . . . . . . . . . . 5-251
performance . . . . . . . . . . . . . . . . . . 5-252
stp . . . . . . . . . . . . . . . . . . . . . . . . . 5-252
(router-lan) . . . . . . . . . . . . . . . . . . . . . 5-253
(router-trunk) . . . . . . . . . . . . . . . . . . . 5-254
(v54) . . . . . . . . . . . . . . . . . . . . . . . . . 5-256
clock . . . . . . . . . . . . . . . . . . . . . . . . . 5-230
equipment . . . . . . . . . . . . . . . . . . . . . 5-238
ipds0 . . . . . . . . . . . . . . . . . . . . . . . . . 5-240
lsprotect . . . . . . . . . . . . . . . . . . . . . . . 5-241
sessions . . . . . . . . . . . . . . . . . . . . . . . 5-255
store . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-257
switch
(ds3) . . . . . . . . . . . . . . . . . . . . . . . . . . 5-259
activeimage . . . . . . . . . . . . . . . . . . . . 5-258
controller . . . . . . . . . . . . . . . . . . . . . . 5-258
telnet
(router) . . . . . . . . . . . . . . . . . . 5-260, 5-261
clock
set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-74
Axxius 800 - Release 2.2
set DS3 . . . . . . . . . . . . . . . . . . . . . . . . . . 5-83
show . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-178
status . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-230
clock1
set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-75
clock2
set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-75
Command Line . . . . . . . . . . . . . . . . . Glossary-5
Command Line Interface (CLI) . . . . . . . . . . 1-10
connect
(router-trunk) (t1) command . . . . . . . . . . 5-41
command . . . . . . . . . . . . . . . . . . . . . . . . . 5-40
Control Panel
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15
Control Panel Interface Jumpers . . . . . . . . . 1-14
Control Panel Interfaces . . . . . . . . . . . . . . . 1-11
Controller card
DS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
card configuration . . . . . . . . . . . . . . . . . 6-9
CLI commands . . . . . . . . . . . . . . . . . . . 6-9
DS3
card configuration . . . . . . . . . . . . . . . . 7-11
CLI commands . . . . . . . . . . . . . . . . . . 7-11
crossconnect
channel associated signaling (CAS)
Conversion . . . . . . . . . . . . . . . 5-40
command . . . . . . . . . . . . . . . . . . . . . . . . . 5-40
CSU . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-6
D
date
set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-75
show . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-180
DCE
data port V.35 card . . . . . . . . . . . . . . . . . 16-7
DDS . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-6
delete
(ds1)
ais command . . . . . . . . . . . . . . . . . . . . 5-43
Index - 7
Index
D
(router)
dhcp server option command . . . . . . . 5-44
dns proxy command . . . . . . . . . . . . . . 5-44
remote command . . . . . . . . . . . . . . . . 5-45
snmp community command . . . . . . . . 5-45
snmp trap command . . . . . . . . . . . . . . 5-46
static dns host command . . . . . . . . . . . 5-46
uploaduser command . . . . . . . . . . . . . 5-47
(router-lan)
filter command . . . . . . . . . . . . . . . . . . 5-48
secondary ip address command . . . . . 5-49
static ip address command . . . . . . . . . 5-50
static ip network command . . . . . . . . . 5-51
static ipx network command . . . . . . . . 5-52
static mac address command . . . . . . . 5-53
(router-wan)
firewall command . . . . . . . . . . . . . . . . 5-53
gre network command . . . . . . . . . . . . 5-54
nat bypass command . . . . . . . . . . . . . . 5-54
static ip address command . . . . . . . . . 5-55
static ip network command . . . . . . . . . 5-56
static ipx network command . . . . . . . . 5-56
static mac address command . . . . . . . 5-57
static nat address command . . . . . . . . 5-57
command . . . . . . . . . . . . . . . . . . . . . . . . . 5-42
user command . . . . . . . . . . . . . . . . . . . . . 5-58
DHCP . . . . . . . . . . . . . . . . . . . . . . . . Glossary-7
Diagnostics and Performance Tools
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
DIP switches
FXO voice card . . . . . . . . . . . . . . . . . . . . . 8-6
disconnect
command . . . . . . . . . . . . . . . . . . . . . . . . . 5-58
display alarms . . . . . . . . . . . . . . . . . . . . . . . . C-4
DS0 . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-7
label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-74
signaling types . . . . . . . . . . . . . . . . . . . . . 8-7
status . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-231
Index - 8
DS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-40, 8-7
Connection Ports . . . . . . . . . . . . . . . . . . 1-13
Connector . . . . . . . . . . . . . . . . . . . . . . . . 1-13
connector pinout . . . . . . . . . . . . . . . . . . . 1-13
Controller card . . . . . . . . . . . . . . . . . . . . . 6-1
card configuration . . . . . . . . . . . . . . . . 6-9
CLI commands . . . . . . . . . . . . . . . . . . . 6-9
technical specifications . . . . . . . . . . . . 6-4
Equipment Loop . . . . . . . . . . . . . . . . . . . C-12
Line Loop . . . . . . . . . . . . . . . . . . . . . . . . . C-7
Loopbacks . . . . . . . . . . . . . . . . . . . . . . . . . C-7
DS1
Equipment Loop . . . . . . . . . . . . . . C-12
Line Loop . . . . . . . . . . . . . . . . . . . . . C-7
Payload Loop . . . . . . . . . . . . . . . . . . C-9
Receiving DS1
CSU Loop . . . . . . . . . . . . . . . . . . . C-10
Payload Loop . . . . . . . . . . . . . . . . . . . . . . C-9
status . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-232
status performance . . . . . . . . . . . . . . . . 5-233
status performance history . . . . . . . . . . 5-234
DS3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Controller card
card configuration . . . . . . . . . . . . . . . 7-11
CLI commands . . . . . . . . . . . . . . . . . . 7-11
Controller card . . . . . . . . . . . . . . . . . . . 7-1
technical specifications . . . . . . . . . . . . 7-3
set
clock . . . . . . . . . . . . . . . . . . . . . . . . . . 5-83
status . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-235
performance history . . . . . . . . . . . . . 5-237
status performance . . . . . . . . . . . . . . . . 5-236
DSO signaling types . . . . . . . . . . . . . . . . . . . 8-7
DTE V.35 cable . . . . . . . . . . . . . . . . . . . . . 16-7
Dual V.35 card . . . . . . . . . . . . . . . . . .16-1, 17-1
cables . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-6
card configuration . . . . . . . . . . . . . .16-5, 17-6
CLI commands . . . . . . . . . . . . . . . .16-5, 17-6
connector pinouts . . . . . . . . . . . . . . . . . . 16-7
Axxius 800 - Release 2.2
Index
E
features . . . . . . . . . . . . . . . . . . . . . . 16-3, 17-4
LEDs . . . . . . . . . . . . . . . . . . . . . . . 16-8, 17-8
overview . . . . . . . . . . . . . . . . . . . . 16-2, 17-2
E
Electronics Protection Mode . . . . . . . . . . . . . 7-8
EMDW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
EMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
EMW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
encapsulation . . . . . . . . . . . . . . . . . . . . . . . 5-150
enhanced security . . . . . . . . . . . . . . . . . . . . 5-110
Enterprise MIB Support . . . . . . . . . . . . . . . . B-3
Ethernet
connector . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16
ethernet
connector pinout . . . . . . . . . . . . . . . . . . . 1-13
show . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-184
exit command . . . . . . . . . . . . . . . . . . . . . . . . 5-59
external alarms . . . . . . . . . . . . . . . . . . . . . . . 5-86
F
faceplates . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7
FDL . . . . . . . . . . . . . . . . . . . . . . . . . .Glossary-8
ferrite beads . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
foreign exchange office (FXO) card . . . . . . . 8-1
Frame . . . . . . . . . . . . . . . . . . . . . . . . .Glossary-9
FX . . . . . . . . . . . . . . . . . . . . . . . . . . . .Glossary-9
FXO . . . . . . . . . . . . . . . . . . . . . . . . . .Glossary-9
FXO Voice card . . . . . . . . . . . . . . . . . . . . . . . 8-1
card configuration . . . . . . . . . . . . . . . . . . . 8-5
Channel Associated Signaling . . . . . . . . . . 8-7
CLI commands . . . . . . . . . . . . . . . . . . . . . . 8-5
DIP switch settings . . . . . . . . . . . . . . . . . . 8-6
features . . . . . . . . . . . . . . . . . . . . 6-3, 7-3, 8-3
LEDs . . . . . . . . . . . . . . . . . . . 6-10, 7-12, 8-6
overview . . . . . . . . . . . . . . . . . . 6-2, 7-2, 8-2
signaling types . . . . . . . . . . . . . . . . . . . . . . 8-7
technical specifications . . . . . . . . . . . . . . . 8-3
Axxius 800 - Release 2.2
FXS . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-9
FXS Voice card . . . . . . . . . . . . . . . . . . . . . . 11-1
card configuration . . . . . . . . . . . . . . . . . . 11-5
CLI commands . . . . . . . . . . . . . . . . . . . . 11-5
features . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7
overview . . . . . . . . . . . . . . . . . . . . . . . . . 11-2
technical specifications . . . . . . . . . . . . . . 11-3
G
Ground . . . . . . . . . . . . . . . . . . . . . . . . Glossary-9
ground start (GS) . . . . . . . . . . . . . . . . . . . . . . 8-7
H
HDB3 . . . . . . . . . . . . . . . . . . . . . . . . Glossary-10
hot swap cards . . . . . . . . . . . . . . . . . . . . . . . 12-7
I
impedance settings . . . . . . . . . . . . . . . . . . . 5-188
Input Power Fuse . . . . . . . . . . . . . . . . . . . . . . 3-7
insert cards . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7
install (slot) router command . . . . . . . . . . . . 5-59
IP . . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-10
IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-86
ISDN BRI . . . . . . . . . . . . . . . . 9-2, Glossary-11
ISDN BRI card . . . . . . . . . . . . . . . . . . 9-1, 10-1
3-DSO BRITE mode . . . . . . . . . . . . . . . . . 9-2
card configuration . . . . . . . . . . . . . . . . . . . 9-6
CLI commands . . . . . . . . . . . . . . . . . . . . . 9-6
connector pinouts . . . . . . . . . . . . . . . . . . . 9-8
features . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
overview . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
technical specifications . . . . . . . . . . . . . . . 9-3
J
jumpers
Interface card . . . . . . . . . . . . . . . . . . . . . . 1-14
Index - 9
Index
L
L
label
DS0 connection . . . . . . . . . . . . . . . . . . . . 5-74
FXSPS connection . . . . . . . . . . . . . . . . . 5-74
Router trunk connection . . . . . . . . . . . . . 5-74
V.35 connection . . . . . . . . . . . . . . . . . . . 5-74
LEDs
dual V.35 card . . . . . . . . . . . . . . . . 16-8, 17-8
FXO voice card . . . . . . . . . . . 6-10, 7-12, 8-6
FXS voice card . . . . . . . . . . . . . . . . . . . . 11-7
ISDN BRI card . . . . . . . . . . . . . . . . . . . . . 9-7
OCU-DP card . . . . . . . . . . . . . . . . . . . . . 10-9
power supply . . . . . . . . . . . . . . . . . . . . . . 12-6
quad DS1 ADPCM . . . . . . . . . . . . . . . . 13-12
quad T1 . . . . . . . . . . . . . . . . . . . . . . . . . 14-10
router card . . . . . . . . . . . . . . . . . . . . . . . 15-19
LLC . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-12
LMI . . . . . . . . . . . . . 5-110, 5-111, Glossary-12
load
tftp command . . . . . . . . . . . . . . . . . . . . . 5-60
xmodem command . . . . . . . . . . . . . . . . . 5-61
local and remote network management . . . . 1-10
Local Management . . . . . . . . . . . . . . . . . . . 1-10
LOF . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-12
log command . . . . . . . . . . . . . . . . . . . . . . . . 5-62
Loopback
DS1
Equipment Loop . . . . . . . . . . . . . . . . . C-12
Line Loop . . . . . . . . . . . . . . . . . . . . . . . C-7
Payload Loop . . . . . . . . . . . . . . . . . . . . C-9
Receiving DS1
CSU Loop . . . . . . . . . . . . . . . . . . . . . . C-10
V.35 Equipment Loop . . . . . . . . . . . . . . . C-16
V.35 Line Loop . . . . . . . . . . . . . . . . . . . . C-14
V.35/V.54 Loop . . . . . . . . . . . . . . . . . . . C-18
loopback . . . . . . . . . . . . . . . . . . . . . Glossary-12
loopstart . . . . . . . . . . . . . . . . . . . . . . Glossary-12
LOS . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-12
Index - 10
LS (Loop Start) . . . . . . . . . . . . . . . . . . . . . . . 8-7
LULT . . . . . . . . . . . . . . . . . . . . . . . Glossary-13
LUNT . . . . . . . . . . . . . . . . . . . . . . . Glossary-13
M
Management Ports . . . . . . . . . . . . . . . . . . . 1-10
Management, Local and Remote . . . . . . . . 1-10
MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
Enterprise support . . . . . . . . . . . . . . . . . . . B-3
public support . . . . . . . . . . . . . . . . . . . . . . B-5
router Enterprise support . . . . . . . . . . . . . B-4
router public support . . . . . . . . . . . . . . . . . B-7
Structure . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
N
network management . . . . . . . . . . . . . . . . . 1-10
O
OCU-DP . . . . . . . . . . . . . . . . . . . . . Glossary-14
OCU-DP card . . . . . . . . . . . . . . . . . . . . . . . 10-1
alarms . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
basic setup . . . . . . . . . . . . . . . . . . . . . . . 10-8
card configuration . . . . . . . . . . . . . . . . . . 10-7
CLI commands . . . . . . . . . . . . . . . . . . . . 10-7
connector pinouts . . . . . . . . . . . . . . . . . 10-13
features . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5
jumper settings . . . . . . . . . . . . . . . . . . . 10-10
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9
overview . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
technical specifications . . . . . . . . . . . . . . 10-5
OOS . . . . . . . . . . . . . . . . . . . . . . . . Glossary-14
P
password
ppp . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-127
router . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-114
user . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-169
Physical Information . . . . . . . . . . . . . . . . . . . 1-8
ping
Axxius 800 - Release 2.2
Index
Q
command . . . . . . . . . . . . . . . . . . . . . . . . . 5-63
pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-11
10Base-T Ethernet . . . . . . . . . . . . . . . . . 15-17
10Base-T ethernet . . . . . . . 10-13, 11-6, 14-9
Dual V.25 card . . . . . . . . . . . . . . . . . . . . . 16-7
external alarm connector . . . . . . . . . 3-9, 3-10
ISDN BRI card . . . . . . . . . . . . . . . . . . . . . 9-8
OCU-DP card . . . . . . . . . . . . . . . . . . . . . 10-13
quad DS1 ADPCM card . . . . . . . . . . . . 13-11
quad T1 card . . . . . . . . . . . . . . . . . 11-6, 14-9
RJ-48C . . . . . . . . . . . . . . . . . . . . . . . . . . 15-17
Router card . . . . . . . . . . . . . . . . . . . . . . . 10-13
RS-232 . . . . . . . . . . . . . . . . . . . . . . . . . . 15-17
TSR card . . . . . . . . . . . . . . . . . . . . . . . . 15-17
PLAR . . . . . . . . . . . . . . . . . . . 5-76, Glossary-15
port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-115
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . 12-1
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6
removal . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7
print
config command . . . . . . . . . . . . . . . . . . . 5-64
help command . . . . . . . . . . . . . . . . . . . . . 5-65
Protection
Electronics . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Protocol . . . . . . . . . . . . . . . . . . . . . .Glossary-15
Public MIB Support . . . . . . . . . . . . . . . . . . . B-5
PVC . . . . . . . . . . . . . . . . . . . . . . . . .Glossary-15
Q
Quad DS1 ADPCM card . . . . . . . . . . . . . . . 13-1
card configuration . . . . . . . . . . . . . . . . . . 13-6
CLI commands . . . . . . . . . . . . . . . . . . . . . 13-6
connector pinouts . . . . . . . . . . . . . . . . . . 13-11
cross-connects . . . . . . . . . . . . . . . . . . . . . 13-9
features . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-3
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-12
overview . . . . . . . . . . . . . . . . . . . . . . . . . 13-2
technical specifications . . . . . . . . . . . . . . 13-3
Quad T1 card . . . . . . . . . . . . . . . . . . . . . . . . 14-1
Axxius 800 - Release 2.2
card configuration . . . . . . . . . . . . . . . . . . 14-7
CLI commands . . . . . . . . . . . . . . . . . . . . 14-7
connector pinouts . . . . . . . . . . . . . 11-6, 14-9
features . . . . . . . . . . . . . . . . . . . . . . . . . . 14-3
jumper settings . . . . . . . . . . . . . . 13-10, 14-8
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-10
overview . . . . . . . . . . . . . . . . . . . . . . . . . 14-2
technical specifications . . . . . . . . . . . . . . 14-4
R
reboot . . . . . . . . . . . . . . . . . . . . . . . . . 5-66, 5-67
router . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-131
Receiving DS1
CSU Loop . . . . . . . . . . . . . . . . . . . . . . . .C-10
remote and local network management . . . . 1-10
Remote Management . . . . . . . . . . . . . . . . . . 1-10
remove cards . . . . . . . . . . . . . . . . . . . . . . . . 12-7
rename (router) command . . . . . . . . . . . . . . 5-65
reset
(controller) . . . . . . . . . . . . . . . . . . . . . . . . 5-66
(router) coldboot command . . . . . . . . . . . 5-67
(router) command . . . . . . . . . . . . . . . . . . 5-66
restore defaults command . . . . . . . . . . . . . . 5-67
RIP . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-15
RJ-45 Connector . . . . . . . . . . . . . . . . . . . . . 1-13
RJ-48C . . . . . . . . . . . . . . . . . . 11-6, 13-11, 14-9
RJ-48C connector . . . . . . . . . . . . . . . . . . . . 1-13
Robbed Bit . . . . . . . . . . . . . . . . . . . . Glossary-16
Router
Enterprise MIB Support . . . . . . . . . . . . . .B-4
Public MIB Support . . . . . . . . . . . . . . . . .B-7
Router card
CLI commands . . . . . . . . . . . . . . . . . . . . 15-8
connector pinouts . . . . . . . . . . . . . . . . . 10-13
features . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-19
overview . . . . . . . . . . . . . . . . . . . . . . . . . 15-2
technical specifications . . . . . . . . . . . . . . 15-4
RS-232 . . . . . . . . . . . . . . . . . . . . . . . . . 1-10, 4-2
Index - 11
Index
S
connector pinout . . . . . . . . . . . . . . . . . . . 1-12
data port . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
rtrping command . . . . . . . . . . . . . . . . . . . . . 5-68
S
security
enhanced . . . . . . . . . . . . . . . . . . . . . . . . 5-110
Service Cards . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-69
(bri)
command . . . . . . . . . . . . . . . . . . . . . . 5-72
mode command . . . . . . . . . . . . . . . . . . 5-73
pmsync command . . . . . . . . . . . . . . . . 5-73
(ds0)
command . . . . . . . . . . . . . . . . . . . . . . 5-76
signal command . . . . . . . . . . . . . . . . . 5-76
type command . . . . . . . . . . . . . . . . . . . 5-77
(ds1 card)
t1/e1 spantype command . . . . . . . . . . 5-81
(ds1 card) adpcm map command . . . . . . 5-82
(ds1 card) command . . . . . . . . . . . . . . . . 5-81
(ds1) command . . . . . . . . . . . . . . . . . . . . 5-78
(ds3)
clock command . . . . . . . . . . . . . . . . . . 5-83
command . . . . . . . . . . . . . . . . . . . . . . 5-83
(fxo) command . . . . . . . . . . . . . . . . . . . . 5-87
(fxsPS) command . . . . . . . . . . . . . . . . . . 5-88
(ocudp)
baud command . . . . . . . . . . . . . . . . . . 5-97
loopback command . . . . . . . . . . . . . . . 5-98
loopdetect command . . . . . . . . . . . . . . 5-99
mvec command . . . . . . . . . . . . . . . . . 5-100
secondary command . . . . . . . . . . . . . 5-100
selftest command . . . . . . . . . . . . . . . 5-101
up/down command . . . . . . . . . . . . . . 5-101
(router)
autologout command . . . . . . . . . . . . 5-102
default command . . . . . . . . . . . . . . . 5-102
dhcp
Index - 12
command . . . . . . . . . . . . . . . . . . .
disable command . . . . . . . . . . . . .
relay server command . . . . . . . . .
server dnsserver command . . . . . .
server domain command . . . . . . .
server duration command . . . . . . .
server netbios nameserver
command . . . . . . . .
server netbios nodetype command
server netbios scope command . .
server startaddr command . . . . . .
dns . . . . . . . . . . . . . . . . . . . . . . . . . .
domain command . . . . . . . . . . . . .
name command . . . . . . . . . . . . . .
resolver command . . . . . . . . . . . .
server command . . . . . . . . . . . . . .
enhanced security command . . . . . .
lmi . . . . . . . . . . . . . . . . . . . . . . . . . .
poll command . . . . . . . . . . . . . . .
login
auth command . . . . . . . . . . . . . . .
prompt command . . . . . . . . . . . . .
ntp . . . . . . . . . . . . . . . . . . . . . . . . . . .
enable/disable command . . . . . . .
poll command . . . . . . . . . . . . . . .
server command . . . . . . . . . . . . . .
timezone command . . . . . . . . . . .
password command . . . . . . . . . . . . .
port
baudrate command . . . . . . . . . . . .
command . . . . . . . . . . . . . . . . . . .
databits command . . . . . . . . . . . .
dsr low reset command . . . . . . . .
flowcontrol command . . . . . . . . .
inactivity timer command . . . . . .
ip command . . . . . . . . . . . . . . . . .
name command . . . . . . . . . . . . . .
parity command . . . . . . . . . . . . . .
passive command . . . . . . . . . . . . .
5-103
5-103
5-103
5-104
5-104
5-105
5-105
5-106
5-106
5-107
5-108
5-108
5-108
5-109
5-109
5-110
5-110
5-111
5-111
5-112
5-112
5-112
5-113
5-113
5-114
5-114
5-115
5-115
5-116
5-116
5-117
5-118
5-118
5-119
5-119
5-120
Axxius 800 - Release 2.2
Index
S
password command . . . . . . . . . . . . 5-120
prompt command . . . . . . . . . . . . . 5-121
protocolport command . . . . . . . . . 5-121
stopbits command . . . . . . . . . . . . . 5-122
tbos map description command . . . 5-122
tbos map display command . . . . . . 5-123
type command . . . . . . . . . . . . . . . . 5-124
ppp auth . . . . . . . . . . . . . . . . . . . . . . . 5-125
byremote protocol command . . . . . 5-125
byremote secret command . . . . . . . 5-125
byremote user command . . . . . . . . 5-126
ofremote protocol command . . . . . 5-126
ppp security . . . . . . . . . . . . . . . . . . . . 5-127
address command . . . . . . . . . . . . . 5-127
password command . . . . . . . . . . . . 5-127
server command . . . . . . . . . . . . . . 5-128
proxy command . . . . . . . . . . . . . . . . . 5-129
reboot command . . . . . . . . . . . . . . . . 5-131
rip command . . . . . . . . . . . . . . . . . . . 5-131
snmp . . . . . . . . . . . . . . . . . . . . . . . . . 5-132
contact command . . . . . . . . . . . . . 5-132
location command . . . . . . . . . . . . . 5-132
name command . . . . . . . . . . . . . . . 5-133
stp . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-134
bridge forwarddelay command . . . 5-134
bridge hellotime command . . . . . . 5-134
bridge maxage command . . . . . . . 5-135
bridge priority command . . . . . . . . 5-135
enable/disable command . . . . . . . . 5-136
syslog . . . . . . . . . . . . . . . . . . . . . . . . . 5-137
enable/disable command . . . . . . . . 5-137
facility command . . . . . . . . . . . . . . 5-137
level command . . . . . . . . . . . . . . . 5-138
server command . . . . . . . . . . . . . . 5-138
(router-lan)
filter forward command . . . . . . . . . . . 5-139
framing command . . . . . . . . . . . . . . . 5-140
gateway command . . . . . . . . . . . . . . . 5-141
ip address command . . . . . . . . . . . . . 5-142
ipx network command . . . . . . . . . . . . 5-143
Axxius 800 - Release 2.2
name - see rename command . . . . . . . 5-65
phy command . . . . . . . . . . . . . . . . . . 5-144
rip
command . . . . . . . . . . . . . . . . . . . 5-145
ip command . . . . . . . . . . . . . . . . . 5-145
ipx command . . . . . . . . . . . . . . . . 5-146
stp
enable/disable command . . . . . . . . 5-147
port cost command . . . . . . . . . . . . 5-148
port priority command . . . . . . . . . 5-148
stp command . . . . . . . . . . . . . . . . . . . 5-147
up/down command . . . . . . . . . . . . . . 5-149
(router-trunk)
encapsulation command . . . . . . . . . . 5-150
multilink group command . . . . . . . . . 5-150
speed command . . . . . . . . . . . . . . . . . 5-151
up/down command . . . . . . . . . . . . . . 5-151
(router-wan)
dlci command . . . . . . . . . . . . . . . . . . 5-152
ip address command . . . . . . . . . . . . . 5-155
ip command . . . . . . . . . . . . . . . . . . . . 5-155
ipx command . . . . . . . . . . . . . . . . . . . 5-156
name - see rename command . . . . . . . 5-65
nat
address command . . . . . . . . . . . . . 5-157
command . . . . . . . . . . . . . . . . . . . 5-157
enable/disable command . . . . . . . . 5-158
ports command . . . . . . . . . . . . . . . 5-158
other command . . . . . . . . . . . . . . . . . 5-159
ppp
auth ofremote user command . . . . 5-160
command . . . . . . . . . . . . . . . . . . . 5-160
compression command . . . . . . . . . 5-161
security server command . . . . . . . 5-161
rip
command . . . . . . . . . . . . . . . . . . . 5-162
ip updates command . . . . . . . . . . . 5-162
ipx updates command . . . . . . . . . . 5-162
stp
command . . . . . . . . . . . . . . . . . . . 5-163
Index - 13
Index
S
enable/disable command . . . . . . . 5-163
port cost command . . . . . . . . . . . . 5-164
port priority command . . . . . . . . . 5-164
trunk command . . . . . . . . . . . . . . . . . 5-165
up/down command . . . . . . . . . . . . . . 5-165
(v35) command . . . . . . . . . . . . . . . . . . . 5-170
(v54) command . . . . . . . . . . . . . . . . . . . 5-172
alarms command . . . . . . . . . . . . . . . . . . . 5-71
autoexit command . . . . . . . . . . . . . . . . . . 5-71
cclabel command . . . . . . . . . . . . . . . . . . 5-74
clock command . . . . . . . . . . . . . . . . . . . . 5-74
clock1 command . . . . . . . . . . . . . . . . . . . 5-75
clock2 command . . . . . . . . . . . . . . . . . . . 5-75
command . . . . . . . . . . . . . . . . . . . . . . . . . 5-69
date command . . . . . . . . . . . . . . . . . . . . . 5-75
ethernet ip address command . . . . . . . . . 5-86
external alarms command . . . . . . . . . . . . 5-86
FXO transmit and receive levels . . . . . . . . 8-1
FXS transmit and receive levels . . . . . . . 11-1
id command . . . . . . . . . . . . . . . . . . . . . . . 5-88
idle command . . . . . . . . . . . . . . . . . . . . . 5-89
ip gateway command . . . . . . . . . . . . . . . 5-89
ipds0 command . . . . . . . . . . . . . . . . . . . . 5-90
key command . . . . . . . . . . . . . . . . . . . . . 5-91
login
auth command . . . . . . . . . . . . . . . . . . . 5-91
support command . . . . . . . . . . . . . . . . 5-92
lsbackup command . . . . . . . . . . . . . . . . . 5-92
lsprotect
enable/disable command . . . . . . . . . . . 5-93
manual command . . . . . . . . . . . . . . . . 5-93
nonrevertive command . . . . . . . . . . . . 5-94
remove command . . . . . . . . . . . . . . . . 5-95
revertive command . . . . . . . . . . . . . . . 5-96
screen command . . . . . . . . . . . . . . . . . . 5-166
snmp command . . . . . . . . . . . . . . . . . . . 5-167
time command . . . . . . . . . . . . . . . . . . . . 5-168
user
command . . . . . . . . . . . . . . . . . . . . . 5-169
Index - 14
level command . . . . . . . . . . . . . . . . .
password command . . . . . . . . . . . . .
verification command . . . . . . . . . . . . . .
show . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(bri) command . . . . . . . . . . . . . . . . . . .
(ds0) command . . . . . . . . . . . . . . . . . . .
(ds1) command . . . . . . . . . . . . . . . . . . .
(ds3) command . . . . . . . . . . . . . . . . . . .
(fxo) command . . . . . . . . . . . . . . . . . . .
(fxsPS) command . . . . . . . . . . . . . . . . .
(ocudp) command . . . . . . . . . . . . . . . . .
(router) . . . . . . . . . . . . . . . . . . . . . . . . .
dhcp command . . . . . . . . . . . . . . . . .
dns command . . . . . . . . . . . . . . . . . .
dns proxy command . . . . . . . . . . . . .
lmi command . . . . . . . . . . . . . . . . . .
login command . . . . . . . . . . . . . . . . .
ntp command . . . . . . . . . . . . . . . . . .
port command . . . . . . . . . . . . . . . . . .
ppp command . . . . . . . . . . . . . . . . . .
rip command . . . . . . . . . . . . . . . . . . .
snmp command . . . . . . . . . . . . . . . .
stp command . . . . . . . . . . . . . . . . . .
syslog command . . . . . . . . . . . . . . . .
uploaduser command . . . . . . . . . . . .
(router-lan)
command . . . . . . . . . . . . . . . . . . . . .
filter command . . . . . . . . . . . . . . . . .
static
ip address command . . . . . . . . . . .
ip network command . . . . . . . . . .
ipx network command . . . . . . . . .
mac address command . . . . . . . . .
static command . . . . . . . . . . . . . . . . .
stp command . . . . . . . . . . . . . . . . . .
(router-wan)
command . . . . . . . . . . . . . . . . . . . . .
firewall command . . . . . . . . . . . . . . .
nat bypass command . . . . . . . . . . . .
5-169
5-169
5-174
5-175
5-177
5-181
5-182
5-183
5-185
5-186
5-191
5-193
5-195
5-196
5-196
5-197
5-197
5-198
5-199
5-200
5-201
5-201
5-202
5-202
5-203
5-204
5-206
5-208
5-209
5-209
5-210
5-208
5-211
5-212
5-214
5-214
Axxius 800 - Release 2.2
Index
S
ppp command . . . . . . . . . . . . . . . . . . 5-215
static
ip address command . . . . . . . . . . . 5-216
ip network command . . . . . . . . . . . 5-216
ipx network command . . . . . . . . . . 5-217
mac address command . . . . . . . . . 5-217
static mac address command . . . . . . . 5-218
stp command . . . . . . . . . . . . . . . . . . . 5-218
trunk command . . . . . . . . . . . . . . . . . 5-219
(v35) command . . . . . . . . . . . . . . . . . . . 5-222
(v54) command . . . . . . . . . . . . . . . . . . . 5-223
adpcm command . . . . . . . . . . . . . . . . . . 5-176
autoexit command . . . . . . . . . . . . . . . . . 5-177
cclabels command . . . . . . . . . . . . . . . . . 5-178
clock command . . . . . . . . . . . . . . . . . . . 5-178
connect adpcm command . . . . . . . . . . . 5-180
connect command . . . . . . . . . . . 5-178, 5-179
date command . . . . . . . . . . . . . . . . . . . . 5-180
ethernet command . . . . . . . . . . . . . . . . . 5-184
external alarms command . . . . . . . . . . . 5-184
id command . . . . . . . . . . . . . . . . . . . . . . 5-186
image command . . . . . . . . . . . . . . . . . . . 5-187
impedance command . . . . . . . . . . . . . . . 5-188
ip command . . . . . . . . . . . . . . . . . . . . . . 5-189
ipds0 command . . . . . . . . . . . . . . . . . . . 5-189
login command . . . . . . . . . . . . . . . . . . . 5-189
lsprotect command . . . . . . . . . . . . . . . . . 5-190
ntp command . . . . . . . . . . . . . . . . . . . . . 5-191
radius command . . . . . . . . . . . . . . . . . . . 5-192
screen command . . . . . . . . . . . . . . . . . . 5-219
snmp command . . . . . . . . . . . . . . . . . . . 5-220
syslog command . . . . . . . . . . . . . . . . . . 5-220
time command . . . . . . . . . . . . . . . . . . . . 5-221
users command . . . . . . . . . . . . . . . . . . . 5-221
SMB Connector . . . . . . . . . . . . . . . . . . . . . . 1-11
SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-167
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-167
SNMP Basics . . . . . . . . . . . . . . . . . . . . . . . . B-2
SNMP Interface . . . . . . . . . . . . . . . . . . . . . . B-1
Axxius 800 - Release 2.2
MIB Structure . . . . . . . . . . . . . . . . . . . . . .B-2
SNMP Basics . . . . . . . . . . . . . . . . . . . . . . .B-2
SNMP Trap Reports . . . . . . . . . . . . . . . . . . .B-8
Spanning Tree . . . . . . . . . . . . . . . . . Glossary-16
status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-224
(adpcm)
performance command . . . . . . . . . . . 5-226
performance history command . . . . . 5-227
(adpcm) command . . . . . . . . . . . . . . . . . 5-225
(bri)
command . . . . . . . . . . . . . . . . . . . . . . 5-228
performance command . . . . . . . . . . . 5-229
performance history command . . . . . 5-230
(ds0) command . . . . . . . . . . . . . . . . . . . 5-231
(ds1)
command . . . . . . . . . . . . . . . . . . . . . . 5-232
performance history command . . . . . 5-234
(ds1) command
performance . . . . . . . . . . . . . . . . . . . 5-233
(ds3)
command . . . . . . . . . . . . . . . . . . . . . . 5-235
performance command . . . . . . . . . . . 5-236
performance history command . . . . . 5-237
(fxo) command . . . . . . . . . . . . . . . . . . . 5-239
(fxsPS) command . . . . . . . . . . . . . . . . . 5-240
(fxsPSM) command . . . . . . . . . . . . . . . . 5-240
(ocudp) . . . . . . . . . . . . . . . . . . . . . . . . . 5-242
performance command . . . . . . . . . . . 5-243
performance history command . . . . . 5-244
(router)
alarms command . . . . . . . . . . . . . . . . 5-245
dns command . . . . . . . . . . . . . . . . . . 5-245
events command . . . . . . . . . . . . . . . . 5-246
ip address table command . . . . . . . . . 5-247
ip network table command . . . . . . . . 5-248
ipx network table command . . . . . . . 5-249
ipx server table command . . . . . . . . . 5-250
mac address table command . . . . . . . 5-251
performance command . . . . . . . . . . . 5-252
Index - 15
Index
T
stp command . . . . . . . . . . . . . . . . . . . 5-252
(router-lan) . . . . . . . . . . . . . . . . . . . . . . 5-253
(router-trunk) command . . . . . . . . . . . . 5-254
(v54) command . . . . . . . . . . . . . . . . . . . 5-256
clock command . . . . . . . . . . . . . . . . . . . 5-230
equipment command . . . . . . . . . . . . . . . 5-238
ipds0 command . . . . . . . . . . . . . . . . . . . 5-240
lsprotect command . . . . . . . . . . . . . . . . 5-241
sessions command . . . . . . . . . . . . . . . . . 5-255
store command . . . . . . . . . . . . . . . . . . . . . 5-257
Structure, MIB . . . . . . . . . . . . . . . . . . . . . . . . B-2
switch
(ds3) command . . . . . . . . . . . . . . . . . . . 5-259
activeimage command . . . . . . . . . . . . . 5-258
controller command . . . . . . . . . . . . . . . 5-258
T
T1 . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-17
DSO signaling types . . . . . . . . . . . . . . . . . 8-7
TDM controller card . . . . . . . . . . . . . . . . . . . 3-1
telnet (router) command . . . . . . . . 5-260, 5-261
TFTP . . . . . . . . . . . . . . . . . . . 5-60, Glossary-18
time
set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-168
show . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-221
transmit clock source . . . . . . . . . . . . . . . . . . 5-75
Trap Reports
SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-8
TSR card
connector pinouts . . . . . . . . . . . . . . . . . 15-17
connectors . . . . . . . . . . . . . . . . . . . . . . . . 16-7
pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . 16-7
V.35 Equipment Loop . . . . . . . . . . . . . . . . . C-16
V.35 Line Loop . . . . . . . . . . . . . . . . . . . . . . C-14
V.35 Loopbacks . . . . . . . . . . . . . . . . . . . . . C-14
V.35 Equipment Loop . . . . . . . . . . . . . . C-16
V.35 Line Loop . . . . . . . . . . . . . . . . . . . C-14
V.35/V.54 Loop . . . . . . . . . . . . . . . . . . . C-18
V.35 set command . . . . . . . . . . . . . . . . . . 5-170
V.35/V.54 cards
cables . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-6
V.35/V.54 Loop . . . . . . . . . . . . . . . . . . . . . C-18
V.54 Service Card Description . . . . . . . . . . C-18
V.54 set command . . . . . . . . . . . . . . . . . . 5-172
VC MUX . . . . . . . . . . . . . . . . . . . . . Glossary-19
verification . . . . . . . . . . . . . . . . . . . . . . . . 5-174
voice channels
FXO . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-87
W
weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
U
Unpacking and Inspection . . . . . . . . . . . . . . . 2-2
uploaduser . . . . . . . . . . . . . . . 5-13, 5-47, 5-203
user levels . . . . . . . . . . . . . . . . . . . . . . . . . 5-169
V
V.35 card . . . . . . . . . . . . . . . . . . . . . . 16-1, 17-1
cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-6
Index - 16
Axxius 800 - Release 2.2
Download PDF