Daikin | RXS24LVJU | Installation manual | Daikin RXS24LVJU Installation manual

R410A Split Series
Installation manual
R410A Split series
Manual de instalación
Serie Split R410A
00_CV_3P300674-2.indd 1
10/18/2011 10:38:43 AM
Safety Precautions
•Read these Safety Precautions carefully to ensure correct installation.
•This manual classifies the precautions into DANGER, WARNING and CAUTION. Be sure to follow all the precautions below: they are all important for ensuring safety.
DANGER ......Indicates an imminently hazardous situation which, if not avoided, will result in death or serious
WARNING ....Failure to follow any of WARNING is likely to result in such grave consequences as death or serious
CAUTION .....Failure to follow any of CAUTION may in some cases result in grave consequences.
•The following safety symbols are used throughout this manual:
Be sure to observe this instruction.
Be sure to establish a ground connection.
Never attempt.
•After completing installation, test the unit to check for installation errors. Give the user adequate instructions
concerning the use and cleaning of the unit according to the Operation Manual.
•Refrigerant gas is heavier than air and replaces oxygen. A massive leak could lead to oxygen depletion, especially
in basements, and an asphyxiation hazard could occur leading to serious injury or death.
•If the refrigerant gas leaks during installation, ventilate the area immediately.
Refrigerant gas may produce a toxic gas if it comes in contact with fire such as from a fan heater, stove or cooking device. Exposure to this gas could cause severe injury or death.
•After completing the installation work, check that the refrigerant gas does not leak.
Refrigerant gas may produce a toxic gas if it comes in contact with fire such as from a fan heater, stove or cooking device.
Exposure to this gas could cause severe injury or death.
•Do not ground units to water pipes, telephone wires or lightning rods because incomplete grounding could cause a
severe shock hazard resulting in severe injury or death, and to gas pipes because a gas leak could result in an
explosion which could lead to severe injury or death.
•Safely dispose of the packing materials.
Packing materials, such as nails and other metal or wooden parts, may cause stabs or other injuries. Tear apart and throw away plastic packaging bags so that children will not play with them. Children playing with plastic bags face the danger of death by suffocation.
•Do not install unit in an area where flammable materials are present due to risk of explosion resulting in serious
injury or death.
•Do not ground units to telephone wires or lightning rods because lightning strikes could cause a severe shock
hazard resulting in severe injury or death, and to gas pipes because a gas leak could result in an explosion which
could lead to severe injury or death.
•Installation shall be left to the authorized dealer or another trained professional.
Improper installation may cause water leakage, electrical shock, fire, or equipment damage.
•Install the air conditioner according to the instructions given in this manual.
Incomplete installation may cause water leakage, electrical shock, fire or equipment damage.
•Be sure to use the supplied or exact specified installation parts.
Use of other parts may cause the unit to come to fall, water leakage, electrical shock, fire or equipment damage.
•Install the air conditioner on a solid base that is level and can support the weight of the unit.
An inadequate base or incomplete installation may cause injury or equipment damage in the event the unit falls off the base or comes loose.
•Electrical work shall be carried out in accordance with the installation manual and the national, state and local
electrical wiring codes.
Insufficient capacity or incomplete electrical work may cause electrical shock, fire or equipment damage.
•Be sure to use a dedicated power circuit. Never use a power supply shared by another appliance. Follow all appropriate electrical codes.
•For wiring, use a wire or cable long enough to cover the entire distance with no splices if possible. Do not use an extension cord. Do not put other loads on the power supply. Use an only a separate dedicated power circuit.
(Failure to do so may cause abnormal heat, electric shock, fire or equipment damage.)
•Use the specified types of wires for electrical connections between the indoor and outdoor units. Follow all state and local electrical codes.
Firmly clamp the inter-unit wire so their terminals receive no external stresses. Incomplete connections or clamping may cause terminal overheating, fire or equipment damage.
01_EN_3P300674-2.indd 1
10/5/2011 2:41:53 PM
Safety Precautions
•After connecting all wires be sure to shape the cables so that they do not put undue stress on the electrical covers,
panels or terminals.
Install covers over the wires. Incomplete cover installation may cause terminal overheating, electrical shock, fire or equipment damage.
•When installing or relocating the system, be sure to keep the refrigerant circuit free from all substances other than
the specified refrigerant (R410A), such as air.
(Any presence of air or other foreign substance in the refrigerant circuit causes an abnormal pressure rise which may result in rupture, resulting
in injury.)
•During pump-down, stop the compressor before removing the refrigerant piping.
If the compressor is still running and the stop valve is open during pump-down, air will be sucked in when the refrigerant piping is removed,
causing abnormally high pressure which could lead to equipment damage or and personal injury.
•During installation, attach the refrigerant piping securely before running the compressor.
If the refrigerant pipes are not attached and the stop valve is open during pump-down, air will be sucked in when the compressor is run,
causing abnormally high pressure which could lead to equipment damage and personal injury.
•Be sure to install a ground fault circuit interrupter breaker.
Failure to install a ground fault circuit interrupter breaker may result in electrically shocks, or fire personal injury.
•Do not install the air conditioner where gas leakage would be exposed to open flames.
If the gas leaks and builds up around the unit, it may catch fire.
•Establish drain piping according to the instructions of this manual.
Inadequate piping may cause water damage.
•Tighten the flare nut according to the specified torque. A torque wrench should be used.
If the flare nut is tightened too much, the flare nut may crack over time and cause refrigerant leakage.
•Do not touch the heat exchanger fins.
Improper handling may result in injury.
•Be very careful about product transportation.
Some products use PP bands for packaging. Do not use any PP bands for a means of transportation. It is dangerous.
•Make sure to provide for adequate measures in order to prevent that the outdoor unit be used as a shelter by small
Small animals making contact with electrical parts can cause malfunctions, smoke or fire. Please instruct the customer to keep the area around
the unit clean.
•The temperature of refrigerant circuit will be high, please keep the inter-unit wire away from copper pipes that are
not thermally insulated.
•Electrical work must be performed in accordance with the NEC/CEC by authorized personnel only.
Accessories supplied with the outdoor unit:
A Installation manual
C Tube
D Binding band
01_EN_3P300674-2.indd 2
B Drain socket assembly
10/5/2011 2:41:54 PM
Precautions for Selecting the Location
Choose a place solid enough to bear the weight and vibration of the unit, where the operation sounds will not be amplified.
Choose a location where the hot air discharged from the unit or the operation sounds will not disturb the neighbors of the user.
Avoid installing near bedrooms so that operation sounds will not be a problem.
There must be sufficient space for carrying the unit into and out of the site.
There must be sufficient space for air passage and no obstructions around the air inlet and the air outlet.
The site must be free from the possibility of flammable gas leakage in a nearby place.
Install units, power cords and inter-unit wire at least 10ft (3m) away from television and radio sets. This is to prevent interference
to images and sounds. (Noises may be heard even if they are more than 10ft (3m) away depending on radio wave conditions.)
8) In coastal areas or other places with salty atmosphere of sulfate gas, corrosion may shorten the life of the air conditioner.
9) Since drain flows out of the outdoor unit, do not place anything under the unit which must be kept away from moisture.
Cannot be installed hanging from ceiling or stacked.
When operating the air conditioner in a low outdoor ambient
temperature, be sure to follow the instructions described below.
•To prevent exposure to wind, install the outdoor unit with its suction
side facing the wall.
•Never install the outdoor unit at a site where the suction side may
be exposed directly to wind.
•To prevent exposure to wind, it is recommended to install a baffle
plate on the air discharge side of the outdoor unit.
•In heavy snowfall areas, select an installation site where the snow
will not affect the unit.
Construct a large canopy.
Construct a pedestal.
Install the unit high enough off the
ground to prevent burying in snow.
Precautions on Installation
3/4 inch
•Check the strength and level of the installation ground so that the unit will not cause any operating vibration or noise after installed.
•In accordance with the foundation drawing, fix the unit securely by means of the foundation bolts. (Prepare 4 sets of 5/16 or 3/8 inch (M8 or M10) foundation bolts, nuts and washers each which are available on the market.)
•It is best to screw in the foundation bolts until their ends are 3/4 inch (20mm) from the foundation surface.
01_EN_3P300674-2.indd 3
10/5/2011 2:41:54 PM
Outdoor Unit Installation Drawings
Max. allowable piping length
** Min. allowable piping length
Max. allowable piping height
* Additional refrigerant
required for refrigerant
pipe exceeding
32.8ft (10m) in length.
98.4ft (30m)
4.92ft (1.5m)
65.6ft (20m)
0.21oz/ft (20g/m)
Gas pipe
O.D. 5/8 inch (15.9mm)
Liquid pipe
O.D. 1/4 inch (6.4mm)
* Be sure to add the proper amount of additional refrigerant.
Failure to do so may result in reduced performance.
** The suggested shortest pipe length is 4.92ft (1.5m), in order to avoid
noise from the outdoor unit and vibration.
(Mechanical noise and vibration may occur depending on how
the unit is installed and the environment in which it is used.)
Wrap the insulation
pipe with the finishing
tape from bottom to top.
Allow 11-13/16 inch (300mm)
of work space below the
ceiling surface.
** Set the piping length
from 4.92ft (1.5m) to
98.4ft (30m).
9-7/8 (250) fro
m wall
If there is the danger of the unit falling
or overturning, fix the unit with
foundation bolts, or with wire or other
If the location does not have good
drainage, place the unit on a level
mounting base (or a plastic pedestal).
Install the outdoor unit in a level
position. Failure to do so may result in
water leakage or accumulation.
Allow space for piping
and electrical servicing.
Right side plate
13 350)
t b s)
oo er
(F ent
Also insulate the connection on the outdoor unit.
unit : inch (mm)
Level mounting base
(available separately)
Clamping material
Insulation tube
Bottom frame
Use tape or insulating material on all connections
to prevent air from getting in between the copper
piping and the insulation tube.
Be sure to do this if the outdoor unit is installed
01_EN_3P300674-2.indd 4
10/5/2011 2:41:54 PM
Installation Guidelines
•Where a wall or other obstacle is in the path of outdoor unit’s inlet or outlet airflow, follow the installation guidelines below.
•For any of the below installation patterns, the wall height on the outlet side should be 47-1/4 inch (1200mm) or less.
Wall facing one side
More than
3-15/16 (100)
Walls facing two sides
More than
13-3/4 (350)
or less
Walls facing three sides
More than
13-3/4 (350)
More than
3-15/16 (100)
More than
1-15/16 (50)
More than
3-15/16 (100)
More than
1-15/16 (50)
More than
13-3/4 (350)
More than
1-15/16 (50)
Top view
Top view
Side view
unit: inch (mm)
Outdoor Unit Installation
Installing outdoor unit
1) When installing the outdoor unit, refer to “Precautions for Selecting the Location” and the “Outdoor Unit Installation Drawings”.
2) If drain work is necessary, follow the procedures below.
Drain work
•Use drain plug for drainage.
•If the drain port is covered by a mounting base or floor surface, place additional foot bases of at least 3-15/16 inch
(100mm) in height under the outdoor unit’s feet.
•In cold areas, do not use a drain socket (A), drain caps (B) and a drain hose with the outdoor unit. (Otherwise, drain water may freeze, impairing heating performance.)
1) Insert drain receiver (C) onto drain socket (A) and drain cap (B) beyond 4
projections around drain socket and drain cap.
2) Insert drain socket and drain caps into their matching drain hole; Drain socket
(A) into drain hole I and drain caps (B) into drain hole II and III. After insertion,
turn them about 40° clockwise.
(A) Drain socket
(B) Drain cap
(Be sure not to insert them into wrong drain
holes, or there causes water leakage.)
(View from bottom)
(C) Drain receiver
Check that the drain receiver (C) is correctly engaged with the projections of the drain socket (A) and drain cap (B).
Otherwise, water leakage may result.
(4 points)
(4 points)
3) C
onnect vinyl hose on the market (internal diameter of 1 inch (25mm)) to drain socket (A).
(If the hose is too long and hangs down, fix it carefully to prevent the kinks.)
4) Make sure that there is no water leakage from portion I, II, or III.
If the drain holes of the outdoor unit are covered with the mounting bracket or the floor, raise the unit to provide the space of
more than 3-15/16 inch (100mm) under the leg of the outdoor unit.
01_EN_3P300674-2.indd 5
10/5/2011 2:41:55 PM
Outdoor Unit Installation
Flaring the pipe end
1) Cut the pipe end with a pipe cutter.
2) Remove burrs with the cut surface facing downward so that the chips do not enter the pipe.
3) Put the flare nut on the pipe.
4) Flare the pipe.
5) Check that the flaring is properly made.
(Cut exactly at
right angles.)
Set exactly at the position shown below.
Remove burrs.
Flare tool for R410A
Conventional flare tool
Clutch-type (Rigid-type) Wing-nut type (Imperial-type)
0-0.020 inch
0.039-0.059 inch
Flare’s inner surface
must be flaw-free.
0.059-0.079 inch
The pipe end must
be evenly flared in a
perfect circle.
Make sure that the
flare nut is fitted.
•Do not use mineral oil on flared part.
•Prevent mineral oil from getting into the system as this would reduce the lifetime of the units.
•Never use piping which has been used for previous installations. Only use parts which are delivered with the unit.
•Never install a drier to this R410A unit in order to guarantee its lifetime.
•The drying material may dissolve and damage the system.
•Incomplete flaring may cause refrigerant gas leakage.
Refrigerant piping
•Use the flare nut fixed to the main unit to prevent it from cracking and deteriorating from age.
•To prevent gas leakage, apply refrigeration oil only to the inner surface of the flare. (Use refrigeration oil for R410A.)
•Use torque wrenches when tightening the flare nuts to prevent damage to the flare nuts and gas leakage.
• Align the centers of both flares and tighten the flare
nuts 3 or 4 turns by hand. Then tighten them fully with
the torque wrenches.
[Apply oil]
Do not apply refrigeration
oil to the outer surface.
Apply refrigeration oil to
the inner surface of the
Flare nut
Do not apply refrigeration oil to
the flare nut to avoid tightening
with excessive torque.
Flare nut tightening torque
Valve cap tightening torque
Gas side
Liquid side
Gas side
Liquid side
5/8 inch (15.9mm)
1/4 inch (6.4mm)
5/8 inch (15.9mm)
1/4 inch (6.4mm)
45.6-55.6ft • lbf
10.4-12.7ft • lbf
35.5-44.0ft • lbf
15.9-20.2ft • lbf
(61.8-75.4N • m)
(14.2-17.2N • m)
(48.1-59.7N • m)
(21.6-27.4N • m)
Service port cap tightening torque
7.9-10.8ft • lbf
(10.8-14.7N • m)
01_EN_3P300674-2.indd 6
10/5/2011 2:41:55 PM
Purging air and checking gas leakage
•Do not mix any substance other than the specified refrigerant (R410A) into the refrigeration cycle.
•When refrigerant gas leaks occur, ventilate the room as soon and as much as possible.
•R410A, as well as other refrigerants, should always be recovered and never be released directly into the environment.
•Use a vacuum pump for R410A exclusively. Using the same vacuum pump for different refrigerants may damage the vacuum
pump or the unit.
•When piping work is completed, it is necessary to purge the air and check for gas
•If using additional refrigerant, perform air purging from the refrigerant pipes and indoor unit using a vacuum pump, then charge additional refrigerant.
•Use a hexagonal wrench (3/16 inch (4mm)) to operate the stop valve rod.
•All refrigerant pipe joints should be tightened with a torque wrench at the specified tightening torque.
Pressure meter
pressure gauge
valve Valve caps
Vacuum pump Service port valve
1) Connect projection side of charging hose (which comes from gauge manifold) to gas stop valve’s service port.
2) Fully open gauge manifold’s low-pressure valve (Lo) and completely close its high-pressure valve (Hi). (High-pressure valve subsequently requires no operation.)
3) Do vacuum pumping and make sure that the compound pressure gauge reads –29.9inHg (–0.1MPa).*1
4) Close gauge manifold’s low-pressure valve (Lo) and stop vacuum pump. (Keep this state for a few minutes to make sure that the compound pressure gauge pointer does not swing back.)*2
5) Remove caps from liquid stop valve and gas stop valve.
6) Turn the liquid stop valve’s rod 90 degrees counterclockwise with a hexagonal wrench to open valve.
Close it after 5 seconds, and check for gas leakage.
Using soapy water, check for gas leakage from indoor unit’s flare and outdoor unit’s flare and valve rods.
After the check is complete, wipe all soapy water off.
7) Disconnect charging hose from gas stop valve’s service port, then fully open liquid and gas stop valves.
(Do not attempt to turn valve rod beyond its stop.)
8) Tighten valve caps and service port caps for the liquid and gas stop valves with a torque wrench at the specified torques.
*1. Pipe length vs. vacuum pump run time
Pipe length
Up to 49.2ft (15m)
More than 49.2ft (15m)
Run time
Not less than 10 min.
Not less than 15 min
*2. If the compound pressure gauge pointer swings back, refrigerant may have water content or a loose pipe joint may exists. Check
all pipe joints and retighten nuts as needed, then repeat steps 2) through 4).
01_EN_3P300674-2.indd 7
10/5/2011 2:41:55 PM
Outdoor Unit Installation
Refilling the refrigerant
Check the type of refrigerant to be used on the machine nameplate.
Precautions when adding R410A
Fill from the gas pipe in liquid form.
It is a mixed refrigerant, so adding it in gas form may cause the refrigerant composition to change, preventing normal operation.
1) Before filling, check whether the cylinder has a siphon attached or not. (It should have something like “liquid filling siphon
attached” displayed on it.)
Filling a cylinder with an attached siphon
Filling other cylinders
Stand the cylinder upright when
Turn the cylinder upside-down
when filling.
There is a siphon pipe inside, so the
cylinder need not be upside-down to
fill with liquid.
•Be sure to use the R410A tools to ensure pressure and to prevent foreign objects entering.
Refrigerant piping work
7-1Caution on pipe handling
1) Protect the open end of the pipe against dust and moisture.
2) All pipe bends should be as gentle as possible. Use a pipe bender for bending.
7-2Selection of copper and heat insulation materials
If no flare cap is
available, cover the
flare mouth with
tape to keep dirt or
water out.
When using commercial copper pipes and fittings, observe the following:
1) Insulation material: Polyethylene foam
Heat transfer rate: 0.041 to 0.052W/mK (0.024 to 0.030Btu/fth°F (0.035 to 0.045kcal/mh°C))
Be sure to use insulation that is designed for use with HVAC Systems.
2) Be sure to insulate both the gas and liquid piping and to provide insulation dimensions as below.
Gas pipe
Gas side
Liquid side
O.D. 5/8 inch
O.D. 1/4 inch
Minimum bend radius
1-15/16 inch (50mm) 1-3/16 inch (30mm)
or more
or more
Thickness Thickness 0.039 inch (1.0mm) 0.031 inch (0.8mm)
Be sure to
place a cap.
Gas pipe thermal
Liquid pipe thermal
I.D. 5/16-13/32 inch
I.D. 5/8-25/32 inch
Thickness 13/32 inch (10mm) Min.
Inter-unit wire
Gas pipe
Liquid pipe
Liquid pipe
Finishing tape
Drain hose
•Use separate thermal insulation pipes for gas and liquid refrigerant pipes.
01_EN_3P300674-2.indd 8
10/5/2011 2:41:56 PM
Pump Down Operation
In order to protect the environment, be sure to pump down when relocating or disposing of the unit.
Remove the valve cap from liquid stop valve and gas stop valve.
Carry out forced cooling operation.
After 5 to 10 minutes, close the liquid stop valve with a hexagonal wrench.
After 2 to 3 minutes, close the gas stop valve and stop forced cooling operation.
Forced cooling operation
Service port
Gas stop valve
■■ Using the indoor unit on/off switch
Liquid stop valve
Press the indoor unit ON/OFF switch for at least 5 seconds. (The operation will start.)
• Forced cooling operation will stop automatically after around 15 minutes. To stop the operation, press the indoor unit ON/OFF switch.
valve cap
■■ Using the indoor unit’s remote controller
Press “MODE” button and select the cooling mode.
Press “ON/OFF” button to turn on the system.
Press both of “TEMP” button and “MODE” button at the same time.
Press “MODE” button twice. ( will be displayed and the unit will enter forced cooling operation.)
Forced cooling operation will stop automatically after around 30 minutes. To stop the operaion, press “ON/OFF” button.
■■ Using the outdoor unit forced cooling operation switch
Forced cooling operation can be performed when the outdoor unit forced cooling operation switch is pressed within
around 3 minutes after power is supplied.
Press the switch (SW1). (The operation will start.)
• Forced cooling operation will stop automatically after around 15 minutes.
To stop the operation, press the switch (SW1).
switch (SW1)
•Do not use tapped wires, stranded wires, extension cords, or starburst connections, as they may cause overheating, electrical shock, or fire.
•Do not use locally purchased electrical parts inside the product. (Do not branch the power for the drain pump, etc., from the
terminal block.) Doing so may cause electric shock or fire.
•Be sure to install a ground fault circuit interrupter breaker. (One that can handle higher harmonics.) (This unit uses an inverter, which means that it must be used a ground fault circuit interrupter breaker capable handling
harmonics in order to prevent malfunctioning of the ground fault circuit interrupter breaker itself.)
•Use an all-pole disconnection type breaker with at least 1/8 inch (3mm) between the contact point gaps.
•When carrying out wiring connection, take care not to pull at the conduit.
•Do not connect the power wire to the indoor unit. Doing so may cause electric shock or fire.
•Do not turn on the safety breaker until all work is completed.
1) Strip the insulation from the wire (3/4inch (20mm)).
2) Connect the connection wires between the indoor and outdoor units so that the terminal numbers match. Tighten the terminal screws securely. We recommend a flathead screwdriver be used to tighten the screws.
01_EN_3P300674-2.indd 9
Firmly fix the wires with
the terminal screws.
Use AWG16 if the connection wire
length is less than 32.8ft (10m), or
AWG14 if it is 32.8ft (10m) or more.
Outdoor unit
1 23
L1 L2 GR
Use AWG 14 wires.
Ground fault
circuit interrupter
Power supply
60Hz 208-230V
10/5/2011 2:41:56 PM
<Method of mounting conduit>
Pass wires through the conduit and secure them with a lock nut.
Lock nut
Wire retainer
Conduit mounting plate
Service port
Conduit mounting plate
1/2 inch (21.3mm)
Power supply terminal block
D Binding band
C Tube
Secure the wires firmly
using the binding band, as
shown in the figure.
Secure firmly, making sure
no outside pressure is
exerted on the terminals.
• Use the specified wires and
connect them securely.
• Shape the wires so that there
is no lifting of the service hatch
or other structural parts.
Observe the notes mentioned following when wiring to the power supply terminal block.
Precautions to be taken for power supply wiring.
01_EN_3P300674-2.indd 10
10/5/2011 2:41:57 PM
•When connecting the connection wires to the terminal block
using a single core wire, be sure to perform curling.
Problems with the work may cause heat and fires.
Stripping wire at terminal block
•If the stranded wires must be used, make sure to use the round
crimp-style terminal for connection to the power supply terminal
block. Place the round crimp-style terminals on the wires up to
the covered part and secure in place.
Round crimp-style
Stranded wire
•Ground terminal installation Use the following method when installing the
round crimp-style terminal.
Round crimpstyle terminal
Flat washer
Flat washer
Round crimpstyle terminal
3) Pull the wire and make sure that it does not disconnect. Then fix the wire in place with a wire stop.
Facility Setting
(cooling at low outdoor temperature)
This function is designed for facilities such as equipment or computer rooms. It is never to be used in a
residence or office where people occupy the space.
1) You can expand the operation range to 14°F (–10°C) by turning on switch B (SW4) on the PCB. If the outdoor temperature falls
to –0.4°F (–18°C) or lower, the operation will stop. If the outdoor temperature rises, the operation will start again.
Turn on
switch B.
•If the outdoor unit is installed where the heat exchanger of the unit is exposed to direct wind, provide a windbreak wall.
•Intermittent noises may be produced by the indoor unit due to the outdoor fan turning on and off when using facility settings.
•Do not place humidifiers or other items which might raise the humidity in rooms where facility settings are being used. A humidifier might cause dew condensation from the indoor unit outlet vent.
•Use the indoor unit at the highest level of airflow rate.
01_EN_3P300674-2.indd 11
10/5/2011 2:41:58 PM
Trial Operation and Testing
Trial operation and testing
1-1Measure the supply voltage and make sure that it falls in the specified range.
1-2Trial operation should be carried out in either cooling or heating mode.
•In cooling mode, select the lowest programmable temperature; in heating mode, select the highest programmable
1) Trial operation may be disabled in either mode depending on the room temperature.
2) After trial operation is complete, set the temperature to a normal level (78°F to 82°F (26°C to 28°C) in cooling mode,
68°F to 75°F (20°C to 24°C) in heating mode).
3) For protection, the system disables restart operation for 3 minutes after it is turned off.
1-3Carry out the test operation in accordance with the operation manual to ensure that all functions and parts,
such as fin movement, are working properly.
•The air conditioner requires a small amount of power in its standby mode. If the system is not to be used for some
time after installation, shut off the circuit breaker to eliminate unnecessary power consumption.
•If the circuit breaker trips to shut off the power to the air conditioner, the system will restore the original operation
mode when the circuit breaker is opened again.
Test items
Test items
Indoor and outdoor units are installed properly on solid bases.
Fall, vibration, noise
No refrigerant gas leaks.
Incomplete cooling/heating
Refrigerant gas and liquid pipes and indoor drain hose extension are
thermally insulated.
Water leakage
Draining line is properly installed.
Water leakage
System is properly grounded.
Electrical leakage
The specified wires are used for inter-unit wiring.
Inoperative or burn damage
Indoor or outdoor unit’s air inlet or air outlet has clear path of air. Stop valves are opened.
Incomplete cooling/heating
Indoor unit properly receives remote control commands.
01_EN_3P300674-2.indd 12
10/5/2011 2:41:58 PM
Two-dimensional bar code is a code
for manufacturing.
00_CV_3P300674-2.indd 2
(1111) HT
10/18/2011 10:38:43 AM
Download PDF