Shark | S3101 series | Specifications | Shark S3101 series Specifications

OWNER’S GUIDE
S3101 series
S3202 series
S3101_SERIES-S3202_SERIES_11_ENG_IB_100909.indd 1
08/09/10 4:33 PM
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
For Household Use Only
WHEN USING YOUR SHARK
STEAM MOP, BASIC SAFETY
PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED,
INCLUDING THE FOLLOWING:
®
READ ALL INSTRUCTIONS
BEFORE USING YOUR
STEAM MOP.
DANGER OF SCALDING. Please use caution when
using the steam mop. The steam
emitted from the openings is
very hot.
POLARIZED PLUG:
This appliance has a polarized
plug (one blade is wider than
the other). As a safety feature,
this plug will fit into a polarized
outlet only one way. If the
plug does not fit fully into the
outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. Do not attempt to
defeat this safety feature.
1. Use the system only for its intended use.
2. DO NOT use outdoors.
3. DO NOT leave the appliance
unattended when plugged in.
Always unplug the power cord
from the electrical outlet when
not in use and before servicing.
4. DO NOT allow the appliance to
be used as a toy. Close attention
is necessary when used by or
near children, pets or plants. DO
NOT leave appliance unattended
while connected.
5. Use only as described in this
manual.
6. Use only manufacturer’s
recommended accessories.
7. DO NOT operate the appliance
with a damaged plug or cord,
or if the unit has been dropped
or damaged. To avoid the
risk of electric shock, do not
disassemble or attempt to
repair the appliance on your
own. Return the appliance to
EURO-PRO Operating LLC (see
warranty) for examination and
repair. Incorrect re-assembly
or repair can cause a risk of
electrical shock or injury to
persons when the appliance is
used.
8. To protect against a risk of
electric shock, DO NOT immerse
the steam mop into water or any
other liquids.
9. DO NOT handle plug or steam
mop with wet hands or operate
appliance without shoes.
10.DO NOT pull or carry by power
cord, use power cord as handle,
close a door on the power cord,
or pull the power cord around
sharp edges or corners. Keep
power cord away from heated
surfaces.
TOLL FREE: 1-800-798-7398
S3101_SERIES-S3202_SERIES_11_ENG_IB_100909.indd 2-3
11. DO NOT unplug by pulling on
power cord. To unplug, grasp the
plug not the power cord. Do not
use extension cords or outlets
with inadequate current carrying
capacity.
12.DO NOT put any objects into
openings. Do not use with any
opening blocked.
13.DO NOT put hands or feet under
the steam mop. Unit gets very
hot.
14.Use ONLY on flat, horizontal
surfaces. Do not use on walls,
counters or windows.
15.DO NOT use on leather, wax
polished furniture or floors,
synthetic fabrics, velvet or
other delicate, steam sensitive
materials.
16.DO NOT add cleaning solutions,
scented perfumes, oils or any
other chemicals to the water
used in this appliance as this
may damage the unit or make
it unsafe for use. If you live in a
hard water area, we recommend
using distilled water in your
steam mop.
17. When in use, NEVER turn
the appliance over or on its
side. NEVER DIRECT STEAM
TOWARDS PEOPLE, ANIMALS
OR PLANTS.
18.NEVER LEAVE THE STEAM MOP
IN ONE SPOT ON ANY SURFACE
FOR ANY PERIOD OF TIME
WHEN MICRO-FIBER PAD IS
ATTACHED.
19.Carefully remove the micro-fiber
pad immediately after you have
finished using the steam mop.
20.When cleaning the steam mop,
unplug the power cord from the
electrical outlet and clean with a
dry or damp cloth. Do not pour
water or use alcohol, benzene or
paint thinner on the unit.
21.Extreme caution should be
exercised when using this
appliance to clean stairs.
22.Never use steam mop without micro-fiber pad attached.
23.Keep your work area well lit.
24.Store steam mop indoors in a
cool, dry place.
25.To avoid circuit overload, do not
operate another appliance on
the same socket (circuit) as the
steam cleaner.
26.If an extension cord is absolutely
necessary, an extension cord
rated a minimum of 15 ampere,
14 gage cord should be used.
Cords rated for less amperage
may overheat. Care should be
taken to arrange cord so that it
cannotbe pulled or tripped over.
27.DO NOT leave unattended when
the system is connected to a
power supply/electrical outlet.
28.DO NOT store unit with damp/
wet micro-fiber cleaning pad
attached. Never leave the steam
mop in one spot on any surface
for any period of time with a
damp or wet micro-fiber cleaning
pad attached as this will damage
your floors
WARNING: Your steam mop
is designed to clean hard floor
surfaces that will withstand high
heat. Do not use on unsealed
wood or unglazed ceramic floors.
On surfaces that have been
treated with wax or some no wax
floors, the sheen may be removed
by the heat and steam action. It
is always recommended to test an
isolated area of the surface to be
cleaned before proceeding. We
also recommend that you check
the use and care instructions from
the floor manufacturer.
www.sharkclean.com
08/09/10 4:33 PM
Quick Start
Quick Start
ASSEMBLE
1 Fit together the extension tubes
as shown in the illustration.
See page 2 for more detailed
assembly instructions. 2
2 Place the micro-fiber cleaning
cloth underneath the mop head,
with quick fastener strips facing
up. Simply press the pad to the
mop to attach it.
5
1
4
3
FILL
3 Remove the cap to fill the
Water Tank. Using the filling
flask and funnel, fill the tank,
keeping the water under the
“MAX FILL” line. Don’t forget to
replace the cap.
ADJUST 4 For your comfort, you can adjust
the height of the mop. Just lift
the latch on the tube 90 degrees
to the open position. Holding
the handle, extend the tube to
the height that’s right for you
and then close latch to locked
position.
TOLL FREE: 1-800-798-7398
S3101_SERIES-S3202_SERIES_11_ENG_IB_100909.indd 4-5
QUICK TIP: If you find the Steam
Mop difficult to push/pull during
use, then simply increase the
height of the pole.
PRIME STEAM
5 Plug in the mop. Wait 30 seconds
for the unit to heat up and the
steam to be ready.
Push the handle toward the mop
head in a pumping motion. To
prime simply pump the handle
10-15 times to generate the
steam.
QUICK TIP: Customize steam
output by slow or fast mopping
with a forward and backward
motion.
www.sharkclean.com
08/09/10 4:33 PM
English
Contents
Thank you for
purchasing
the Shark®
Steam Mop.
GETTING STARTED.................................................................. 2
USING YOUR STEAM MOP....................................................6
USING YOUR ACCESSORIES................................................ 8
CARE OF YOUR STEAM MOP..............................................9
TROUBLESHOOTING............................................................ 10
WARRANTY AND REGISTRATION.....................................11
This manual covers model numbers:
S3101 11
S3101A 11
S3101C 11
S3101CO 11
S3101CP 11
S3101WT 11
S3101Z 11
S3202 11
S3202C 11
TECHNICAL SPECIFICATIONS
Voltage: 120V., 60Hz.
Power:
1550 Watts
Water Capacity: 250 ml (8 oz.)
TOLL FREE: 1-800-798-7398
S3101_SERIES-S3202_SERIES_11_ENG_IB_100909.indd 6-1
www.sharkclean.com
1
08/09/10 4:33 PM
English
Getting Started
When assembling your steam mop there
may be a little water in or around the
water tank. This is because we test all
our steam mops 100% before you buy
them, so you get a quality Shark®
Steam Mop.
3
Each micro-fiber cleaning pad
has a white or blue colored
tab so that you can use a
different pad for different
tasks. Use one color for tough
grime on tile floors, another
color for stubborn spots on
linoleum and another color
for pet stains. Keep your
floors happy! Always attach
the micro-fiber cleaning pad
to the mop head or you may
scratch your floor surface.
2
c
b
a
d
e
f
g*
FIRST THINGS FIRST, YOU NEED TO
KNOW WHAT’S IN THE BOX YOU
JUST OPENED:
a Upper Extension Tube
b Lower Extension Tube (Telescopic)
c Steam Mop Base
d Micro-Fiber Pads
e Filling Flask
f Funnel
g Carpet Glider*
NOTE: The Carpet Glider* (g) is
an optional attachment and is sold
separately.
2
TOLL FREE: 1-800-798-7398
S3101_SERIES-S3202_SERIES_11_ENG_IB_100909.indd 2-3
YOUR SHARK STEAM MOP IS
EASY TO ASSEMBLE
1 First remove all the parts from the
package. We know you’re excited
about the Shark Steam Mop,
but don’t plug it in until it’s fully
assembled and you’ve read all of the
following instructions.
3 Insert the pieces you assembled in
Step 2 into the pump actuator (the
tube that leads to the tank). Push the
extension tube assembly and pump
actuator together in until you hear it
click into place. Insert cord into cord
clip on the shaft of the steam-mop.
IMPORTANT: Always make sure that
your Steam Mop is unplugged from
the wall before you attach the
micro-fiber cleaning pad.
2 Slide the upper extension tube (the
tube with the handle) into the lower
extension tube (the short tube). Push
the two extension tubes together in
until you hear it click into place. See
illustration for a visual explanation.
www.sharkclean.com
3
08/09/10 4:33 PM
English
Getting Started
1
The water tank cap has an
arrow to indicate the locked
and unlocked position.
Each micro-fiber cleaning pad
has a colored tab so that you
can use a different pad for
different tasks. Use one color
for tough grime on tile floors,
another color for stubborn
spots on linoleum and another
color for pet stains. Keep your
floors happy! Always attach
the micro-fiber cleaning pad
to the mop head or you may
scratch your floor surface.
1
PLACING THE MICRO-FIBER PAD
1 Place the micro-fiber cleaning cloth
underneath the mop head, with
the quick fastener strips facing up.
Simply press the pad on to the Steam Mop.
IMPORTANT: Make sure you only
add water to the tank. Chemicals or
cleaning solution may damage the
appliance and could be unsafe for
you and your family.
4
TOLL FREE: 1-800-798-7398
S3101_SERIES-S3202_SERIES_11_ENG_IB_100909.indd 4-5
NOTE: Don’t be alarmed if the first
time you use your Steam Mop, you
notice water inside the water tank or
drops of water in the packaging. It’s
normal to see this water. Your Steam
Mop was 100% tested in the factory
to ensure your safety and your floor’s
happiness. If you see water in the
unit, it’s from these tests.
To order additional Micro-Fiber pads,
feel free to contact us at www.sharkclean.com or
call 1-800-798-7398.
FILLING THE WATER TANK
IMPORTANT: Before you fill up the
tank, make sure your Steam Mop is
unplugged from the wall.
1 First, remove the water tank cap by
turning it counter clockwise to the
unlocked position. See illustration for a visual explanation.
2 The filling flask and funnel included
with your Steam Mop make filling
the water tank as simple as getting a
glass of water from the sink. Fill the
flask with water and use the funnel to
pour it into the tank. Be sure to keep
the water under the MAX FILL line;
just one flask of water is enough for
your Steam Mop. See illustration for
a visual explanation.
3 Replace the water tank cap by
turning it clockwise to the locked
position.
www.sharkclean.com
5
08/09/10 4:33 PM
English
Using Your Steam Mop
1
Now comes the part you’ve been
waiting for – it’s time to use your steam
mop. When you use your steam mop for
the first time or haven’t used the unit
in awhile, it may take a minute or two
for the water to make its way through
the pump and into the heater to create
steam. Get it started by pumping the
handle a few times. If you’ve waited a
few minutes and you still don’t see any
steam, reference the troubleshooting
section on page 10.
When your Steam Mop stops
steaming, it could be out of
water. Unplug the power cord
from the electrical outlet
and refill the water tank at
anytime.
3
4
2
IMPORTANT: Your Steam Mop needs
water to make steam! Never use your
Steam Mop without water in the tank.
Sweep or vacuum your floors
before using your Steam Mop. Your
Steam Mop was designed to get
rid of stuck-on gunk, grime, paw/
footprints and it will do a better job
if yesterday’s cereal crumbs aren’t in
the way.
Visit www.sharkclean.com for other
great quick cleaning products to
complement your Steam Mop.
6
TOLL FREE: 1-800-798-7398
S3101_SERIES-S3202_SERIES_11_ENG_IB_100909.indd 6-7
1 Pull and twist the quick release
cord holder to unwrap the power
cord completely. Plug into a 120volt electrical outlet. The “On” light
will turn green. Success! If your
light doesn’t turn on reference the
Troubleshooting section on page 10.
2 For your comfort, you can adjust the
height of the mop. Just lift the latch
on the tube 90 degrees to the open
position. Holding the handle, extend
the tube to the height that’s right for
you and then close latch to locked
position.
3 It takes about 30 seconds for the
steam to get going. Now pump the
handle a few times to prime the
pump and activate steam.
4 Mop with a forward and backward
motion to customize steam output
automatically.
QUICK TIP: If you find the Steam
Mop difficult to push/pull during use,
then simply increase the height of
the pole.
IMPORTANT: When your floors are
sparkling clean and you’re finished
with your Steam Mop, unplug it from
the electrical outlet and carefully
remove the micro-fiber cleaning
pad from the mop head. Always
remove the micro-fiber cleaning pad
from the mop head when you have
finished using your Steam Mop to
avoid damage to your floors. The
steam will make your micro-fiber
cleaning pad very hot. You may want
to wait a couple of minutes to let it
cool off before you remove it.
www.sharkclean.com
7
08/09/10 4:33 PM
Using Your Accessories (optional)
English
Care of Your Steam Mop
The Steam Mop won’t clean
your carpeting or areas rugs,
but it’s great for deodorizing
and freshening carpets and
area rugs.
Always remove the microfiber cleaning pad from the
Steam Mop head when you
store your Steam Mop to
avoid damage to your floors.
2
1
THE CARPET GLIDER (optional)
Just like you, your Steam Mop
is versatile! The carpet glider
transforms your Steam Mop in no
time. Now you can freshen and
deodorize your carpets and area
rugs with the power of steam.
PUTTING THE CARPET GLIDER ON
1 Set the carpet glider on the carpet
with the smooth side down. Place
the mop head, with the cleaning pad
attached, on top of the carpet glider.
Your Steam Mop will rest on top of
the glider, not attach to it.
8
TOLL FREE: 1-800-798-7398
S3101_SERIES-S3202_SERIES_11_ENG_IB_100909.indd 8-9
USING THE CARPET GLIDER
2 Plug in your Steam Mop and begin
freshening your carpet by pushing
the mop and glider back and forth to
release steam, just as you do on hard
floors. When the carpet is nice and
fresh and you’re finished using the
Steam Mop, unplug it and store it as
you would normally.
KEEPING YOUR MICRO-FIBER
CLEANING PAD AS GOOD AS NEW
Your steam activated micro-fiber
cleaning pad works wonders for you,
so return the favor by giving it the
care it deserves.
1 Wash pads in warm water. Wash
separately from other laundry.
Only use liquid detergent. (no
powder detergent) Don’t use any
fabric softeners.
Line dry or dry on a low dryer
setting.
2 If there are loose threads on the pad
careful cut the thread with scissors.
Don’t pull on them or cut at the base.
KEEPING YOUR STEAM MOP
IN TIP-TOP SHAPE
If you love your Steam Mop, let it
show. Caring for your Steam Mop
and properly storing it means you’ll
get the same super steam action you
expect each time you use it.
IMPORTANT: Both your Steam Mop
and the water inside it can get very
hot, so let it cool down completely
before you store it.
IMPORTANT: Always store the
Steam Mop in a safe place away from
children and high traffic areas. NOTE: It’s a good idea to use
distilled water in your tank to help
prolong the life of your Steam Mop,
especially if you live in an area with
hard water.
www.sharkclean.com
9
08/09/10 4:33 PM
Trouble Shooting
PROBLEM
English
Ordering Replacement Parts
POSSIBLE REASONS & SOLUTIONS
The Steam Mop
will not turn-on.
Your steam-mop should be securely plugged into a 120V AC electrical outlet only. Check your fuse or breaker.
If your unit still doesn’t work, give us a call 1-800-798-7398.
Steam Mop will not
make steam.
Is there water in the water tank? If not, add water to your
Steam Mop following instructions.
Steam Mop leaves
water on the floor.
Is your micro-fiber cleaning pad too wet? Why don’t
you unplug your Steam Mop and change the micro-fiber
cleaning pad.
Steam Mop left white
spot on the floor.
Don’t leave your steam-mop on the floor with a damp or
wet cleaning pad.
Do you have hard water? If you do you might want to
switch to distilled water.
b
The pad might be dirty, change the pad.
If you washed the pocket with powder detergent then the
pad might have residual detergent left on it. Wash it again
with liquid detergent.
Floors are cloudy,
streaky or spotty
after steaming.
If you are cleaning in a kitchen area where there might be a
build-up of grease then use a de greasing agent such as an
all-purpose cleaner or dish soap and paper towels to clean
the area first.
This might be leftover from past cleaners used on the floor
surface. Use the steam mop a few more times and see if the leftover cloudiness is removed. 10
c
You might have left the mop in the same spot for too long.
Do you have hard water? If you do you might want to
switch to distilled water.
Steam Mop is hard
to push.
a
ORDERING REPLACEMENT PARTS
To order additional parts and
accessories, feel free to contact us at
www.sharkclean.com or
call 1-800-798-7398.
NOTE: Some parts may be available
at your local retailer.
PART
PART NO.
a Micro-Fiber Pads
b Filling Flask & Funnel
c Carpet Glider
XT3101W
1015SO
XCG3101
Make sure the cleaning pad is on properly.
If you find the Steam Mop difficult to push/pull during use,
then simply increase the height of the pole.
TOLL FREE: 1-800-798-7398
S3101_SERIES-S3202_SERIES_11_ENG_IB_100909.indd 10-11
www.sharkclean.com
11
08/09/10 4:33 PM
ONE (1) YEAR LIMITED WARRANTY
English
Notes
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions
within the warranty period, return the complete appliance and accessories, freight prepaid. For
Customer Service support, call 1 (800) 798-7398 or visit our website www.sharkclean.com.
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating
LLC will repair or replace it free of charge. Proof of purchase date and a check made payable
to EURO-PRO Operating LLC in the amount of $ 9.95 to cover the cost of return shipping and
handling must be included. *
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or
replacement of the unit at our option. This warranty does not cover normal wear of parts and
does not apply to any unit that has been tampered with or used for commercial purposes. This
limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage
due to faulty packaging or mishandling in transit. This warranty does not cover damage or
defects caused by or resulting from damages from shipping or repairs, service or alterations to
the product or any of its parts, which have been performed by a repair person not authorized by
EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or
conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to
the specific obligations expressly assumed by it under the terms of the limited warranty. In no
event is EURO-PRO Operating LLC liable for incidental or consequential damages of any nature
whatsoever. Some states/provinces do not permit the exclusion or limitation of incidental or
consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address and
phone number with a note giving purchase information, model number and what you believe
is the problem with item. We recommend you insure the package (as damage in shipping is
not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”. We are constantly striving to improve our products, therefore the specifications
contained herein are subject to change without notice.
OWNERSHIP REGISTRATION CARD FOR
CANADIAN CONSUMERS ONLY
Please complete and return within ten (10) days of purchase. The registration will enable
us to contact you in the event a product defect is discovered. By returning this card you
acknowledge to have read and understood the instructions for use, and warnings set
forth in the accompanying instructions.
RETURN TO: EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec H4S 1A7
PURCHASER: ……………………………………..........................………………………………………………………............
ADDRESS: …………………………………………………………………..........................……………………………...............
DATE OF PURCHASE: ……………….................…….. MODEL: …………........……...................................
NAME AND ADDRESS OF STORE: …………..........................................………………………………………..
12
TOLL FREE: 1-800-798-7398
S3101_SERIES-S3202_SERIES_11_ENG_IB_100909.indd 12-13
www.sharkclean.com
13
08/09/10 4:33 PM
U.S.: EURO-PRO Operating LLC
Newton, MA 02459
Canada:
EURO-PRO Operating LLC
4400 Bois Franc
Ville St. Laurent, Québec H4S 1A7
1-800-798-7398
www.sharkclean.com
COPYRIGHT© EURO-PRO OPERATING LLC 2010
PRINTED IN CHINA S3101.SERIES.EF.100908
S3202.SERIES.EF.100908
Illustrations may differ from actual product.
S3101_SERIES-S3202_SERIES_11_ENG_IB_100909.indd 14
08/09/10 4:33 PM
Download PDF