York | AFFINITY BHP024 | Installation manual | York AFFINITY BHP024 Installation manual

INSTALLATION
MANUAL
AFFINITY™ SERIES
SINGLE PACKAGE HEAT PUMPS
CONTENTS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
MODEL: B*HP024 thru 060
2 thru 5 Ton
(13 SEER)
REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . .3
PRODUCT NOMENCLATURE . . . . . . . . . . . . . . . . . . . .3
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . .15
See the following page for a complete Table of Contents.
NOTES, CAUTIONS AND WARNINGS
Installer should pay particular attention to the words:
NOTE, CAUTION, and WARNING. Notes are intended to
clarify or make the installation easier. Cautions are given
to prevent equipment damage. Warnings are given to
alert installer that personal injury and/or equipment damage may result if installation procedure is not handled
properly.
CAUTION:
READ ALL SAFETY GUIDES BEFORE YOU
BEGIN TO INSTALL YOUR UNIT.
ISO 9001
Certified Quality
SAVE THIS MANUAL
Management System
268709-YIM-C-0908
268709-YIM-C-0908
TABLE OF CONTENTS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
LIST OF FIGURES
Fig. #
Pg. #
1
CENTER OF GRAVITY . . . . . . . . . . . . . . . . . . . . . . . . 4
2
TYPICAL FIELD WIRING DIAGRAM . . . . . . . . . . . . . . 6
PRODUCT NOMENCLATURE . . . . . . . . . . . . . . . . . . . . . . 3
3
CLEARANCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4
DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
LIMITATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5
DEMAND DEFROST “CURVE” SELECTION
JUMPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6
TYPICAL WIRING DIAGRAM BHP MODELS 208/230-1-60 POWER SUPPLY . . . . . . . . . . . . . . . . 16
7
TYPICAL WIRING DIAGRAM BHP MODELS 208/230-3-60 POWER SUPPLY . . . . . . . . . . . . . . . . 17
8
TYPICAL WIRING DIAGRAM BHP MODELS 460/575-3-60 POWER SUPPLY . . . . . . . . . . . . . . . . 18
REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
RIGGING AND HANDLING . . . . . . . . . . . . . . . . . . . . 4
CLEARANCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
DUCTWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
CONDENSATE DRAIN . . . . . . . . . . . . . . . . . . . . . . . . 5
SERVICE ACCESS . . . . . . . . . . . . . . . . . . . . . . . . . . 5
LIST OF TABLES
THERMOSTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
POWER AND CONTROL WIRING . . . . . . . . . . . . . . . 5
Tbl. #
COMPRESSORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1
UNIT APPLICATION DATA . . . . . . . . . . . . . . . . . . . . . 4
SEQUENCE OF OPERATION . . . . . . . . . . . . . . . . . . . . . . 11
2
UNIT DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ANTI-SHORT CYCLE TIMER . . . . . . . . . . . . . . . . . . 11
3
PHYSICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
COOLING OPERATION . . . . . . . . . . . . . . . . . . . . . . 11
4
ELECTRICAL DATA (13 SEER HEAT PUMP /
ELECTRIC HEAT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5
SIDE & BOTTOM SUPPLY AIR BLOWER
PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6
ADDITIONAL STATIC PRESSURE RESISTANCE. . . . 9
7
DEMAND DEFROST SELECTION . . . . . . . . . . . . . . . 12
HEATING OPERATION . . . . . . . . . . . . . . . . . . . . . . 11
DEFROST OPERATION . . . . . . . . . . . . . . . . . . . . . . . 11
HEAT PUMP SAFETY SWITCH OPERATION . . . . . . 12
ELECTRIC HEAT LIMIT SWITCH OPERATION . . . . 12
SECURE OWNER'S APPROVAL . . . . . . . . . . . . . . . . . . . 12
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
NORMAL MAINTENANCE . . . . . . . . . . . . . . . . . . . . 15
Pg. #
8
THERMOSTAT SIGNALS (SINGLE PHASE UNITS) . 13
9
THERMOSTAT SIGNALS (THREE PHASE UNITS) . . 14
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2
Johnson Controls Unitary Products
268709-YIM-C-0908
GENERAL
REPLACEMENT PARTS
YORK Model B*HP units are factory assembled heat
pumps designed for outdoor installation on a roof top or
a slab. Field-installed electric heater accessories are
available to provide supplemental electric heat combined with electric cooling and heating.
Refer to User’s Maintenance and Service Information
Manual for complete listing of replacement parts on this
equipment.
The units are completely assembled on rigid, removable base rails. All piping, refrigerant charge, and electrical wiring is factory installed and tested. The units
require only electric power and duct connections at the
point of installation.
This product must be installed in strict compliance with the enclosed installation instructions
and any applicable local, state, and national
codes including, but not limited to, building,
electrical, and mechanical codes.
The electric heaters have nickel-chrome resistance wire
elements and utilize single point power connection.
INSPECTION
As soon as a unit is received, it should be inspected for
possible damage during transit. If damage is evident,
the extent of the damage should be noted on the carrier's freight bill. A separate request for inspection by
the carrier's agent should be made in writing. Refer to
Form 50.15-NM for additional information.
Improper installation may create a condition
where the operation of the product could cause
personal injury or property damage.
REFERENCE
De-energize the electrical power to the unit
before attempting to inspect, repair or perform
maintenance to the unit.
Additional information on the design, installation, operation and service of this equipment is available in the
following reference forms:
•
268709 — General Installation
•
035-16605-003 — Electric Heater Accessory
Installer should pay particular attention to the words:
NOTE, CAUTION and WARNING. Notes are intended
to clarify or make the installation easier. Cautions are
given to prevent equipment damage. Warnings are
given to alert installer that personal injury and/or equipment damage may result if installation procedure is not
handled properly.
PRODUCT NOMENCLATURE
PRODUCT NOMENCLATURE
B
3
H P
0
2
4
A
0
6
PRODUCT CATEGORY
B = Single Package Heat Pumps
(Air Cooled)
VOLTAGE CODE
06 = 208/230-1-60
25 = 208/230-3-60
46 = 460-3-60
58 = 575-3-60
PRODUCT GENERATION
3 = Third Generation
4 = Fourth Generation
PRODUCT IDENTIFIER
HP = Heat Pump (13 SEER)
Johnson Controls Unitary Products
NOMINAL COOLING
CAPACITY (MBH)
024 = 24,000 BTUH 042 = 42,000 BTUH
030 = 30,000 BTUH 048 = 48,000 BTUH
036 = 36,000 BTUH 060 = 60,000 BTUH
FACTORY
INSTALLED ELECTRIC HEAT
A = No Electric Heat Installed
3
268709-YIM-C-0908
INSTALLATION
ponents. Unit must be installed on a level roof curb or
appropriate angle iron frame providing adequate support under the compressor/condenser section.
LIMITATIONS
These units must be installed in accordance with the
following national and local safety codes.
1. National Electrical Code ANSI/NFPS No. 70 or Canadian Electrical Code Part 1, C22.1 (latest editions).
2. Local plumbing and waste water codes and other
applicable local codes.
Refer to Table 1 for unit application data and to Table 4
for electric heat application data.
If components are to be added to a unit to meet local
codes, they are to be installed at the dealer's and/or
the customer's expense.
Size of unit for proposed installation should be based
on heat loss/heat gain calculations made in accordance with industry recognized procedures identified
by the Air Conditioning Contractors of America.
TABLE 1: Unit Application Data
Voltage Variation,
1
Min./Max.
208/230 V
Care must be exercised when moving the unit. Do not
remove any packaging until the unit is near the place of
installation. Rig unit with slings placed under the unit.
Spreader bars of sufficient length should be used
across the top of the unit.
BEFORE LIFTING A UNIT, MAKE SURE THAT ITS
WEIGHT IS DISTRIBUTED EQUALLY ON THE
CABLES SO THAT IT WILL LIFT EVENLY.
Units may also be moved or lifted with a fork-lift. Slotted openings in the skid are provided for this purpose.
Forks must pass completely through the base.
Refer to Table 2 for unit weights and to Figure 1 for
approximate center of gravity.
187/253
432/504
575 V
540/630
Wet Bulb Temperature (°F) of Air on
Evaporator Coil, Min./Max.
Condenser Coil, Min.3/Max.
RIGGING AND HANDLING
TABLE 2: Unit Dimensions
2
460 V
Dry Bulb Temperature (°F) of Air on
5. Maintain level tolerance of unit to 1/8" maximum.
57/72
45/125
1. Rated in accordance with ARI Standard 110, utilization
range “A”.
2. “T1" transformer primary tap must be moved from the 230
volt connection to the 208 volt connection for low voltage
applications of 208 volt and below.
3. A low ambient accessory is available for operation down to
0°F.
LOCATION
Size
024
030
036
042
048
060
Shipping
Weight
(lbs.)
356
353
388
440
485
495
Operating
Weight
(lbs.)
351
348
383
435
480
490
“D”
97
96
106
120
132
135
93
93
102
115
127
130
81
81
89
101
111
113
84
84
92
104
115
117
“C”
“B”
49
26
CLEARANCES
4
“C”
“A”
1. Unit is designed for outdoor installation only.
4. For roof top installation, be sure the structure can support the weight of the unit plus any field installed com-
“B”
CENTER OF GRAVITY
FRONT
OF
UNIT
FIGURE 1 - Center of Gravity
3. For ground level installation, a level pad or slab
should be used. The thickness and size of the pad
or slab used should meet local codes and unit
weight. Do not tie the slab to the building foundation.
“A”
“D”
Use the following guidelines to select a suitable location for these units.
2. Condenser must have an unlimited supply of air.
Where a choice of location is possible, position unit
on either north or east side of building.
Dimensions
23
47
All units require certain clearances for proper operation
and service. Refer to Figures 3 & 4 for the clearances
required for construction, servicing and proper unit
operation.
Do not permit overhanging structures or shrubs
to obstruct the condenser air discharge outlets.
Johnson Controls Unitary Products
268709-YIM-C-0908
DUCTWORK
These units are adaptable to downflow use as well as
rear supply and return air duct openings. To convert to
downflow, use the following steps:
1. Remove the duct covers found in the bottom return
and supply air duct openings. There are four (4)
screws securing each duct cover (save these
screws to use later).
Filters should be checked monthly especially since this
unit is used for both heating and cooling.
CONDENSATE DRAIN
A condensate trap is required to be installed in the condensate drain. The plumbing must conform to local
codes. Use a sealing compound on male pipe threads.
Install the condensate drain line (¾" NPTF) to spill into
an open drain.
2. Install the duct covers, removed in step one, to the
rear supply and return air duct openings. Secure
with the four (4) screws used in step one.
3. Seal duct covers with silicone caulk.
Downflow units must have an “L”-shaped supply duct
without any outlets or registers located below the outlet
of the unit.
Duct work should be designed and sized according to
the methods of the Air Conditioning Contractors of
America (ACCA), as set forth in their Manual D.
A closed return duct system shall be used. This shall
not preclude use of economizers or ventilation air
intake. Flexible joints may be used in the supply and
return duct work to minimize the transmission of noise.
Hand tighten only.
SERVICE ACCESS
Access to all serviceable components is provided by
the following removable panels:
•
•
•
Blower service access
Electrical/Filter access
Compressor service access
Refer to Figures 3 & 4 for location of these access panels and minimum clearances.
THERMOSTAT
When fastening ductwork to side duct flanges
on unit, insert screws through duct flanges
only. DO NOT insert screws through casing.
Outdoor ductwork must be insulated and
waterproofed.
NOTE: Be sure to note supply and return openings.
Refer to Figure 4 for information concerning rear and
bottom supply and return air duct openings.
The room thermostat should be located on an inside
wall approximately 56" above the floor where it will not
be subject to drafts, sun exposure or heat from electrical fixtures or appliances. Follow manufacturer's
instructions enclosed with the thermostat for general
installation procedure. Six color coded insulated wires
(minimum #18 AWG) should be used to connect thermostat to unit. See Figure 2.
POWER AND CONTROL WIRING
Single phase units are shipped without a filter and is
the responsibility of the installer to secure a filter in the
return air ductwork or install a Filter/Frame Kit
(1FF0114).
Field wiring to the unit must conform to provisions of
the current N.E.C. ANSI/NFPA No. 70 or C.E.C. and/or
local ordinances. The unit must be electrically
grounded in accordance with local codes or, in their
absence, with the N.E.C./C.E.C. Voltage tolerances
which must be maintained at the compressor terminals
during starting and running conditions are indicated on
the unit Rating Plate and Table 3.
A filter rack and a high velocity filters are standard on
three phase units.
The wiring entering the cabinet must be provided with
mechanical strain relief.
Filters must always be used and must be kept clean.
When filters become dirt laden, insufficient air is delivered by the blower, decreasing your unit's efficiency
and increasing operating costs and wear-and-tear on
the unit and controls.
A fused disconnect switch should be field provided for
the unit. If any of the wire supplied with the unit must be
replaced, replacement wire must be of the type shown
on the wiring diagram.
FILTERS
Johnson Controls Unitary Products
5
268709-YIM-C-0908
Electrical line must be sized properly to carry the load.
Each unit must be wired with a separate branch circuit
fed directly from the meter panel and properly fused.
Units are shipped with compressor mountings factoryadjusted and ready for operation.
Refer to Figure 2 for typical field wiring and to the
appropriate unit wiring diagram for control circuit and
power wiring information.
Do Not loosen compressor mounting bolts.
COMPRESSORS
CONTROL WIRING
UNIT TERMINAL STRIP
THERMOSTAT
** = Minimum wire size of 18 AWG
wire should be used for all field
installed 24 volt wire.
PROGRAMMABLE
THERMOSTAT ONLY
NOTE:
HEAT ANTICIPATOR
SHOULD BE SET AT 0.25
AMPS FOR ALL MODELS.
**
24 VOLT TRANSFORMER
*
* = Only required on units with
supplemental electric heat.
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can
cause improper and dangerous operation. Verify proper operation after servicing.
POWER WIRING
REFER TO ELECTRICAL DATA
TABLES TO SIZE THE
DISCONNECT SWITCH,
WIRING & OVERCURRENT
PROTECTION.
REFER TO ELECTRICAL DATA
TABLES TO SIZE THE
DISCONNECT SWITCH,
WIRING & OVERCURRENT
PROTECTION.
FIGURE 2 - Typical Field Wiring DIagram
TABLE 3: Physical Data
Models
030
036
042
048
060
CENTRIFUGAL BLOWER (Dia. x Wd. in.)
FAN MOTOR HP
10 X 8
10 X 8
11 x 10
11 x 10
11 x 10
11 x 10
1/2
1/2
3/4
3/4
3/4
1
3
3
3
3
3
INDOOR
COIL
ROWS DEEP
FINS PER INCH
FACE AREA (Sq. Ft.)
2
15
13
15
16
16
16
4.38
4.38
4.38
5.63
5.63
5.63
22
22
22
22
22
22
OUTDOOR
FAN
PROPELLER DIA. (in.)
FAN MOTOR HP
NOM. CFM TOTAL
1/4
1/4
1/4
1/4
1/4
1/2
1,800
1,800
2,400
2,400
3,000
3,000
1
1
2
2
2
2
OUTDOOR
COIL
ROWS DEEP
FINS PER INCH
FACE AREA (Sq. Ft.)
20
20
20
20
20
20
11.7
11.7
11.7
16.4
16.4
16.4
CHARGE
REFRIGERANT 22 (lbs./oz.)
5/5
5/15
8/8
9/14
12/0
10/4
FILTER
FACE AREA (Sq. Ft./Qty./Size)
COMPRESSOR
HERMETIC Type, (Qty. = 1)
Scroll
Scroll
INDOOR
BLOWER
6
BHP
024
4.28/2/14" x 22"
Reciprocating
Scroll
Scroll
Reciprocating
Johnson Controls Unitary Products
268709-YIM-C-0908
TABLE 4: Electrical Data (13 SEER Heat Pump / Electric Heat)
Size
(Tons)
024
RLA
LRA
MCC
OD Fan
Motors
(each)
FLA
208/230-1-60
9.3
57
15
1.2
4.1
208/230-1-60
13.4
73
21
1.2
4.1
208/230-3-60
9.0
63
14
1.2
4.1
460-3-60
4.5
31
7
0.8
2.1
208/230-1-60
15.4
88
24
1.2
6.0
208/230-3-60
10.2
77
16
1.2
6.0
460-3-60
5.1
39
8
0.8
3.0
575-3-60
4.2
31
7
0.6
2.4
208/230-1-60
16.0
86
24
1.2
6.0
Volt
Compressors
(each)
Supply
Blower
Motor
FLA
030
036
Electric Heat Option
Model
None
2NH04500506
2NH04500706
2NH04501006
None
2NH04500506
2NH04500706
2NH04501006
2NH04501506
None
2NH04501025
2NH04501525
None
2NH04501046
2NH04501546
None
2NH04500506
2NH04500706
2NH04501006
2NH04501506
None
2NH04501025
2NH04501525
None
2NH04501046
2NH04501546
None
2NH04501058
2NH04501558
None
2NP04501006
2NP04501506
2ND04501506
042
208/230-3-60
12.0
84
18
1.2
6.0
460-3-60
5.8
42
9
0.8
3.0
575-3-60
5.1
34
8
0.6
2.4
208/230-1-60
23.4
126
37
1.2
6.0
208/230-3-60
12.9
93
20
1.2
6.0
460-3-60
6.4
47
10
0.8
3.0
575-3-60
5.1
37
8
0.6
2.4
048
Johnson Controls Unitary Products
None
2NP04501025
2NP04501525
None
2NP04501046
2NP04501546
None
2NP04501058
2NP04501558
None
2NP04501006
2NP04501506
2NP04502006
2NP04502506
None
2NP04501025
2NP04501525
2NP04502025
2NP04502525
None
2NP04501046
2NP04501546
2NP04502046
2NP04502546
None
2NP04501058
2NP04501558
2NH04502058
2NH04502558
kW
3.8/5
5.6/7.5
7.5/10
3.8/5
5.6/7.5
7.5/10
11.3/15
7.5/10
11.3/15
10
15
3.8/5
5.6/7.5
7.5/10
11.3/15
7.5/10
11.3/15
10
15
10
15
7.5/10
11.3/15
3.8/5
7.5/10
7.5/10
11.3/15
10
15
10
15
7.5/10
11.3/15
15/20
18.8/25
7.5/10
11.3/15
15/20
18.8/25
10
15
20
25
10
15
20
25
Stages
1
2
2
1
2
2
2
1
1
1
1
1
2
2
2
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
2
2
2
2
1
1
2
2
1
1
2
2
1
1
2
2
Amps
18.1/20.8
27.1/31.3
36.1/41.7
18.1/20.8
27.1/31.3
36.1/41.7
54.2/62.5
20.8/24.1
31.3/36.1
12
18
18.1/20.8
27.1/31.3
36.1/41.7
54.2/62.5
20.8/24.1
31.3/36.1
12
18
9.6
14.4
36.1/41.7
54.2/62.5
18.1/20.8
36.1/41.7
20.8/24.1
31.3/36.1
12
18
9.6
14.4
36.1/41.7
54.2/62.5
72.2/83.3
90.3/104.2
20.8/24.1
31.3/36.1
41.7/48.1
52.1/60.1
12
18
24.1
30.1
9.6
14.4
19.2
24.1
MCA1
(Amps)
Max Fuse2/
Breaker3 Size
(Amps)
16.9
39.5/43
50.8/56
62.1/69
22.1
44.6/48.1
55.9/61.1
67.2/74.1
89.8/100.2
16.6
42.6/46.6
55.6/61.7
8.5
23.5
31
26.5
49/52.5
60.3/65.5
71.6/78.5
94.2/104.6
20
46/50
59/65.1
10.1
25.2
32.7
8.3
20.3
26.3
27.2
72.3/78.5
94.9/104.6
49.8/52.5
72.3/78.5
22.2
48.3/51.6
61.3/66.7
11
26
33.6
9.4
21.4
27.4
36.5
81.6/88.5
104.2/114.6
126.7/140.6
149.3/166.7
23.3
49.4/53.4
62.4/68.4
75.4/83.5
88.5/98.5
11.8
26.8
34.4
41.9
49.4
9.4
21.4
27.4
33.4
39.4
25
40/45
60/60
70/70
30
50/50
60/70
70/80
90/110
20
45/50
60/70
15
25
35
35
50/60
70/70
80/80
100/110
25
50/60
60/70
15
30
35
15
25
30
35
80/80
100/110
60/60
80/80
30
50/60
70/70
15
30
35
15
25
30
45
90/100
110/125
150/150
150/175
30
50/60
70/70
80/90
90/100
15
30
35
45
50
15
25
30
35
40
7
268709-YIM-C-0908
TABLE 4: Electrical Data (13 SEER Heat Pump / Electric Heat) (Continued)
Size
(Tons)
Compressors
(each)
Volt
RLA
LRA
MCC
OD Fan
Motors
(each)
FLA
Supply
Blower
Motor
FLA
208/230-1-60
25.0
150
39
2.3
7.6
208/230-3-60
17.3
123
27
2.3
7.6
460-3-60
8.4
70
13
1.3
3.8
575-3-60
7.0
53
11
1.1
3.0
060
Electric Heat Option
Model
None
2NP04501006
2NP04501506
2NH04502006
2NP04502506
None
2NH04501025
2NH04501525
2NH04502025
2NH04502525
None
2NP04501046
2NH04501546
2NH04502046
2NP04502546
None
2NH04501058
2NH04501558
2NH04502058
2NH04502558
kW
7.5/10
11.3/15
15/20
18.8/25
7.5/10
11.3/15
15/20
18.8/25
10
15
20
25
10
15
20
25
Stages
2
2
2
2
1
1
2
2
1
1
2
2
1
1
2
2
Amps
36.1/41.7
54.2/62.5
72.2/83.3
90.3/104.2
20.8/24.1
31.3/36.1
41.7/48.1
52.1/60.1
12
18
24.1
30.1
9.6
14.4
19.2
24.1
MCA1
(Amps)
Max Fuse2/
Breaker3 Size
(Amps)
41.2
86.3/93.2
108.9/119.3
131.4/145.3
154/171.4
31.5
57.6/61.6
70.6/76.6
83.6/91.7
96.7/106.7
15.6
30.6
38.2
45.7
53.2
12.9
24.9
30.9
36.9
42.9
50
100/100
110/125
150/150
175/175
40
60/70
80/80
90/100
100/110
20
35
40
50
60
15
25
35
40
45
1. Minimum Circuit Ampacity.
2. Maximum Over Current Protection per standard UL 1995.
3. Fuse or HACR circuit breaker size installed at factory or field installed.
TABLE 5: Side & Bottom Supply Air Blower Performance
Size
(Tons)
024
030
036
042
048
060
8
Blower Speed
Low (1)
Low/Medium (2)
Medium (3)
Medium/High (4)
High (5)
Low (1)
Low/Medium (2)
Medium (3)
Medium/High (4)
High (5)
Low (1)
Low/Medium (2)
Medium (3)
Medium/High (4)
High (5)
Low (1)
Low/Medium (2)
Medium (3)
Medium/High (4)
High (5)
Low (1)
Low/Medium (2)
Medium (3)
Medium/High (4)
High (5)
Low (1)
Low/Medium (2)
Medium (3)
Medium/High (4)
High (5)
CFM
721
769
882
971
828
991
1091
1189
1025
1214
1370
1241
1406
1536
1656
1342
1596
1705
1806
1898
1580
1614
1733
2003
2214
0.2
W
82
93
131
171
110
168
214
269
158
237
305
221
299
376
466
249
397
476
561
652
394
419
508
737
968
RPM
600
628
704
773
673
754
807
861
769
764
779
702
759
808
858
717
817
858
895
929
859
874
924
1030
1104
CFM
611
694
812
916
759
934
1041
1144
1235
906
1125
1276
1416
1151
1325
1461
1584
1687
1250
1513
1624
1726
1819
1504
1540
1663
1922
2089
External Static Pressure (Inch Water Gauge)
0.4
0.6
0.8
W
RPM CFM
W
RPM
CFM
W
97
705
112
730
610
126
832
147
797
736
162
889
651
177
188
857
851
205
939
775
219
957
249
982
887
261
125
771
187
839
868
205
922
783
221
234
883
983
253
958
910
269
288
927
1091
305
994
1027
318
347
970
1186
360
1028 1125
368
175
856
260
839
1034
283
913
942
307
330
846
1179
354
913
1078
377
413
872
1314
436
932
1206
454
1441
530
970
1326
538
245
778
1058
268
853
324
826
1242
349
893
1158
373
403
869
1384
427
928
1305
449
492
912
1509
515
966
1430
533
590
955
1611
610
1004 1527
620
273
789
422
875
1432
447
934
1354
474
501
911
1545
526
966
1466
549
587
945
1646
610
995
1564
628
679
977
1736
698
1023 1646
709
420
917
446
931
536
976
1588
559
1026 1501
572
746
1069 1829
746
1104 1712
728
918
1121 1949
859
1136 1785
787
RPM
979
1019
1052
1003
1033
1061
1086
987
981
993
1022
959
988
1019
1051
995
1021
1046
1069
1072
1134
1148
CFM
681
788
785
912
1007
971
1083
1182
1072
1223
1344
1428
1276
1386
1476
1547
1528
1576
1.0
W
230
266
273
316
352
397
460
521
396
468
542
615
501
571
639
706
659
689
RPM
1097
1120
1106
1132
1147
1048
1051
1070
1025
1046
1070
1097
1058
1077
1096
1112
1146
1154
Johnson Controls Unitary Products
268709-YIM-C-0908
TABLE 6: Additional Static Pressure Resistance1,2
RESISTANCE, IWG
DESCRIPTION
CFM
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
Wet Indoor Coil
0.01 0.01 0.01 0.02 0.01
0.02
0.03
0.04
0.04
0.03
0.04
0.04
0.05
0.05
0.06
2000
0.07
Economizer
0.00 0.00 0.00 0.01 0.01
0.01
0.01
0.02
0.03
0.04
0.05
0.06
0.07
0.07
0.08
0.08
Filter/Frame Kit
0.01 0.02 0.02 0.02 0.02
0.02
0.03
0.03
0.03
0.03
0.04
0.05
0.05
0.06
0.06
0.07
Electric Heat
0.02 0.03 0.03 0.03 0.04
0.04
0.05
0.06
0.07
0.08
0.09
0.10
0.01
0.11
0.11
0.12
1. Deduct these resistance values from the available external static pressures shown in the respective Blower Performance Table.
2. The pressure thru the economizer is greater for 100% outdoor air than for 100% return air. If the resistance of the return air duct system is less than
0.25 IWG, the unit will deliver less CFM during full economizer operation.
CLEARANCES
(Minimum)
Front
12"
Back
0”
Left Side (Filter Access)
24”
Right Side
24”
Below Unit1
0”
Above Unit2
36” For Condenser Air Discharge
MINIMUM CLEARANCE OF 1"
ALL SIDES FOR THE FIRST 3'
OF DUCT FOR 20 & 25 kW.
ZERO INCHES THEREAFTER,
FOR ALL OTHER HEATERS,
ZERO INCH CLEARANCE ALL
SIDES FOR ENTIRE LENGTH
OF DUCT.
1. Units may be installed on combustible floors made from wood or
class A, B or C roof covering material.
2. Units must be installed outdoors. Overhanging structures or shrubs
should not obstruct outdoor air discharge outlet.
NOTE: FOR UNITS APPLIED WITH A ROOF CURB, THE MINIMUM
CLEARANCE MAY BE REDUCED FROM 1 INCH TO 1/2 INCH
BETWEEN COMBUSTIBLE ROOF CURB MATERIAL AND THE
SUPPLY DUCT.
3'
FLEXIBLE DUCT
COLLAR
FIGURE 3 - Clearances
Johnson Controls Unitary Products
9
268709-YIM-C-0908
FRONT
A (OVERALL)
UNIT SIZE
2
DIMENSION
“A”
024 - 036
33
042 - 060
41
2
1
4
NPTF
FRONT
BACK
NPTF
1
1
1
FIGURE 4 - Dimensions
10
Johnson Controls Unitary Products
268709-YIM-C-0908
SEQUENCE OF OPERATION
ANTI-SHORT CYCLE TIMER
This unit has an anti-short cycle timer built in to the
defrost control. This timer will not permit the compressor to start within five minutes after the completion of
the last cycle or power interruption. To bypass the antishort cycle feature, short the “TEST” pins together for 2
seconds.
The following sequences of operation are based on
using a standard single-stage heat pump thermostat.
gizes contactor coil M1 and power is supplied to
the compressor and outdoor fan motor. The reversing valve remains in the heating position. When the
fan switch on the thermostat is in the “AUTO” position, the indoor blower is energized at the heating
airflow.
3. For units equipped with supplementary electric
heat, when the heat pump cannot meet the
demand, the thermostat “W” sends 24 volts to “W2”
on the fan control board. This signal also is sent
through the defrost control terminals “W” and “W6”
and back to the fan control “W1”. The 24 volt signal
energizes all stages of electric heat.
COOLING OPERATION
1. When the fan switch on the thermostat is in the
“ON” position, the 24 volts at “G” will bring on the
indoor blower motor at the cooling airflow. When
the fan switch on the thermostat is in the “AUTO”
position, the blower operates only when there is a
call for cooling by the thermostat.
2. On a call for cooling, the thermostat sends 24 volts
to “Y” and “O” on the fan control and defrost control
boards. The reversing valve solenoid is energized,
and after the anti-short cycle period is complete
contactor coil M1 is energized. Power is supplied
to the compressor and outdoor fan motor, and the
reversing valve switched to the cooling position.
When the fan switch on the thermostat is in the
“AUTO” position the indoor blower motor is energized at the cooling airflow.
3. When the demand for cooling has been satisfied,
the 24 volt “Y” signal is removed, and the M1 contactor is de-energized. When the fan switch on the
thermostat is in the “ON” position, the indoor
blower motor continues to run. If the fan switch is in
the “AUTO” position. the indoor motor ramps down
over a 30-second period.
HEATING OPERATION
1. When the fan switch on the thermostat is in the
“ON” position, the 24 volts at “G” brings on the
indoor blower motor at the heating flow. When the
fan switch on the thermostat is in the “AUTO” position, the blower operates when there is a call for
heating by the thermostat.
2. On a call for heating, the thermostat sends 24 volts
to “Y” on the fan control board. After the anti-short
cycle period is complete, the 24 volt signal ener-
Johnson Controls Unitary Products
4. When the heating demand is satisfied, the electric
heat is de-energized when the 24 volt “W” signal is
removed, and the M1 contactor is de-energized
when the 24 volt “Y” signal is removed. When the
fan switch on the thermostat is in the “ON” position,
the indoor blower continues to run. When the fan
switch is in the “AUTO” position, the indoor blower
motor ramps down over a 15-second period.
Please refer to Tables 8 and 9 for more information.
Defrost Operation
The demand defrost control implements a temperature
differential (”delta-T”) demand defrost algorithm. The
heat pump is allowed to operate in the heating mode
until the combination of outdoor ambient and outdoor
coil temperatures indicate that defrosting is necessary.
When coil temperature is below the initiate point for the
ambient temperature continuously for 4-1/2 minutes,
the heat pump is put into a defrost cycle. This 4-1/2
minute timer eliminates unnecessary defrost cycles
caused by refrigeration surges such as those that
occur at the start of a heating cycle.
A timed inhibit feature prevents the system from
responding to a call for defrost less than 20 minutes
after the initiation of the previous defrost. After the 20
minute inhibit time has expired, temperature conditions
must call for defrost continuously for 4-1/2 minutes
before a defrost cycle is initiated. A temperature inhibit
feature prohibits defrost if the coil temperature is above
40°F.
A forced-defrost feature puts the system into a defrost
period every 6 hours and 4 minutes to recirculate lubricants, unless the coil temperature is above 40°F. All
defrost timing occurs only while the compressor is on.
11
268709-YIM-C-0908
During the defrost mode, the defrost control will provide
a 24 volt signal from terminal “W1/66” to the fan control
terminal “W1”. This signal will energize electric heat
stage 1, if the unit is so equipped.
For trouble shooting purposes, the defrost cycle can be
manually initiated by shorting the “TEST” pins together
for 5 seconds. Defrost will terminate normally during
the “TEST” mode.
TABLE 7: Demand Defrost Selection
Unit
B*HP 036, 048, 060
B*HP 024, 030
B*HP 042
Pin Position
1
2
3
AMBG
R
C
The limit switch responds to over temperature conditions in the air duct. Opening of the device results in
dropping power to the relays. The control logic will also
respond by turning off the relays. After four limit cycle
trips the unit goes into a 1 hour soft lockout period. If
during this period the control “sees” another limit cycle,
the unit will go into a hard lockout condition. Once in a
hard lockout state, the fan is locked on and the heaters
are disabled. Only a power cycle will clear this state.
X/L
R
C
Y
Y
O
O
W1/66
FAN
VALVE
COND
HIGH VOLTAGE
W W1/66
W
REV
PRESSURE
SWITCH
M
FIGURE 5 - Demand Defrost “Curve” Selection
Jumper
Heat Pump Safety Switch Operation
If the unit is equipped with the field installed upgrade
safety package, the refrigeration system will be protected against high or low refrigerant pressure and low
indoor coil temperature. If any of these three safety
12
1. Removing power from the control's thermostat 1st
stage (Y) input for a time not to exceed 5 seconds
(ON-OFF-ON).
Electric Heat Limit Switch Operation
AMBIENT
COIL G
COIL
X/L
DEMAND
DEFROST
SELECTION
JUMPER
(JUMPER
IS SHOWN
IN POSITION
#1)
Resetting the lockout function is accomplished by;
2. Removing power from “R” for more than 2 seconds.
3. Shorting the “TEST” pins together for more than 2
seconds.
TEST
1
2
3
4
switches opens, the unit will be shut off for the 5 minute
anti-short cycle time. Once this has expired, a six hour
elapsed run timer begins. If a second opening of a
safety switch occurs during this six hour period, the
compressor will be locked out.
During the soft lockout period, the fan responds to thermostat input but the heaters are enabled. This is to
sense a failed heater relay. The limit cycle count is
reset at the start of a heat request. If the limit remains
open for period of 80 seconds or more, the control is
immediately put into a hard lockout condition. Only a
power cycle will clear this state.
SECURE OWNER'S APPROVAL
When the system is functioning 1/6 properly, secure
the owner's approval. Show him the location of all disconnect switches and the thermostat. Teach him how
to start and stop the unit and how to adjust temperature
settings within the limitations of the system.
Johnson Controls Unitary Products
268709-YIM-C-0908
TABLE 8: Thermostat Signals (Single Phase Units)
SIGNAL
“G”
STATE
ON
BOARD FUNCTION
FAN INSTANT ON
OFF
FAN INSTANT OFF
ON
FAN INSTANT ON
COMPRESSOR AND OUTDOOR FAN INSTANT ON (AFTER ANTI-SHORT CYCLE DELAY)
REVERSING VALVE ENERGIZED
SYSTEM OPERATES IN COOLING
OFF
COMPRESSOR AND OUTDOOR FAN INSTANT OFF
FAN 60 SEC. DELAY OFF
ON
FAN INSTANT ON
COMPRESSOR AND OUTDOOR FAN INSTANT ON (AFTER ANTI-SHORT CYCLE DELAY)
SYSTEM OPERATES IN HEATING
OFF
COMPRESSOR AND OUTDOOR FAN INSTANT OFF
FAN 60 SEC. DELAY OFF
ON
FAN INSTANT ON
HEATER BANK 1 ELEC. HEAT INSTANT ON
HEATER BANK 2 ELEC. HEAT 10 SEC. DELAY ON
HEATER BANK 3 ELEC. HEAT 20 SEC. DELAY ON
OFF
HEATER BANK 3 ELEC. HEAT INSTANT OFF
HEATER BANK 2 ELEC. HEAT 1/2 SEC. DELAY OFF
HEATER BANK 1 ELEC. HEAT 1 SEC. DELAY OFF
FAN 10 SEC. DELAY OFF
ON
FAN INSTANT ON
COMPRESSOR AND OUTDOOR FAN INSTANT ON
SYSTEM OPERATES IN HEATING
HEATER BANK 1 ELEC. HEAT INSTANT ON
HEATER BANK 2 ELEC. HEAT 10 SEC. DELAY ON
HEATER BANK 3 ELEC. HEAT 20 SEC. DELAY ON
OFF
COMPRESSOR AND OUTDOOR FAN INSTANT OFF
HEATER BANK 3 ELEC. HEAT INSTANT OFF
HEATER BANK 2 ELEC. HEAT 1/2 SEC. DELAY OFF
HEATER BANK 1 ELEC. HEAT 1 SEC. DELAY OFF
FAN 60 SEC. DELAY OFF
ON
FAN INSTANT ON
HEATER BANK 1 ELEC. HEAT INSTANT ON
HEATER BANK 2 ELEC. HEAT 10 SEC. DELAY ON
HEATER BANK 3 ELEC. HEAT 20 SEC. DELAY ON
OFF
HEATER BANK 3 ELEC. HEAT INSTANT OFF
HEATER BANK 2 ELEC. HEAT 1/2 SEC. DELAY OFF
HEATER BANK 1 ELEC. HEAT 1 SEC. DELAY OFF
FAN 10 SEC. DELAY OFF
“G” & “Y” & “O”
“G” & “Y”
“G” & “W”
“G” & “Y” & “W”
“W”
Johnson Controls Unitary Products
13
268709-YIM-C-0908
TABLE 9: Thermostat Signals (Three Phase Units)
SIGNAL
“G”
STATE
ON
OFF
FAN INSTANT OFF
ON
FAN INSTANT ON
COMPRESSOR AND OUTDOOR FAN INSTANT ON (AFTER ANTI-SHORT CYCLE DELAY)
REVERSING VALVE ENERGIZED
SYSTEM OPERATES IN COOLING
OFF
COMPRESSOR AND OUTDOOR FAN INSTANT OFF
FAN 60 SEC. DELAY OFF
ON
FAN INSTANT ON
COMPRESSOR AND OUTDOOR FAN INSTANT ON (AFTER ANTI-SHORT CYCLE DELAY)
SYSTEM OPERATES IN HEATING
OFF
COMPRESSOR AND OUTDOOR FAN INSTANT OFF
FAN 60 SEC. DELAY OFF
ON
FAN INSTANT ON
HEATER BANK 1, 2 & 3 ELEC. HEAT INSTANT ON
HEATER BANK 4, 5 & 6 ELEC. HEAT 10 SEC. DELAY ON
OFF
HEATER BANK 4, 5 & 6 ELEC. HEAT INSTANT OFF
HEATER BANK 1, 2 & 3 ELEC. HEAT 1/2 SEC. DELAY OFF
FAN 10 SEC. DELAY OFF
ON
FAN INSTANT ON
COMPRESSOR AND OUTDOOR FAN INSTANT ON
SYSTEM OPERATES IN HEATING
HEATER BANK 1, 2 & 3 ELEC. HEAT INSTANT ON
HEATER BANK 4, 5 & 6 ELEC. HEAT 10 SEC. DELAY ON
OFF
COMPRESSOR AND OUTDOOR FAN INSTANT OFF
HEATER BANK 4, 5 & 6 ELEC. HEAT INSTANT OFF
HEATER BANK 1, 2 & 3 ELEC. HEAT 1/2 SEC. DELAY OFF
FAN 60 SEC. DELAY OFF
ON
FAN INSTANT ON
HEATER BANK 1, 2 & 3 ELEC. HEAT INSTANT ON
HEATER BANK 4, 5 & 6 ELEC. HEAT 10 SEC. DELAY ON
OFF
HEATER BANK 4, 5 & 6 ELEC. HEAT INSTANT OFF
HEATER BANK 1, 2 & 3 ELEC. HEAT 1/2 SEC. DELAY OFF
FAN 10 SEC. DELAY OFF
“G” & “Y” & “O”
“G” & “Y”
“G” & “W”
“G” & “Y” & “W”
“W”
14
BOARD FUNCTION
FAN INSTANT ON
Johnson Controls Unitary Products
268709-YIM-C-0908
MAINTENANCE
NORMAL MAINTENANCE
Exercise care when cleaning the coil so that
the coil fins are not damaged.
Prior to any of the following maintenance procedures, shut off all power to the unit, to avoid
personal injury.
Do not permit the hot condenser air discharge
to be obstructed by overhanging structures or
shrubs.
TROUBLESHOOTING
Periodic maintenance consists of changing or cleaning
filters and general cleaning of the outdoor coil.
FILTERS - Inspect once a month. Replace Disposable
or clean Permanent Type as necessary. DO NOT
replace Permanent Type with Disposable.
MOTORS - Indoor and outdoor fan motors are permanently lubricated and require no maintenance.
OUTDOOR COIL - Dirt should not be allowed to accumulate on the outdoor coil surface or other parts in the
air circuit. Cleaning should be as often as necessary to
keep the coil clean. Use a brush, vacuum cleaner
attachment, or other suitable means. If water is used to
clean the coil, be sure that the power to the unit is shut
off prior to cleaning.
Johnson Controls Unitary Products
Troubleshooting of components necessarily
requires opening the electrical control box with
the power connected to the unit. Use extreme
care when working with live circuit! Check the
unit nameplate for the correct range before
making any connections with line terminals.
The wire number or color and terminal designations referred to may vary. Check the wiring
label inside the control box access panel for
the correct wiring.
15
268709-YIM-C-0908
FIGURE 6 - Typical Wiring Diagram BHP Models - 208/230-1-60 Power Supply
16
Johnson Controls Unitary Products
268709-YIM-C-0908
FIGURE 7 - Typical Wiring Diagram BHP Models - 208/230-3-60 Power Supply
Johnson Controls Unitary Products
17
268709-YIM-C-0908
FIGURE 8 - Typical Wiring Diagram BHP Models - 460/575-3-60 Power Supply
18
Johnson Controls Unitary Products
268709-YIM-C-0908
Johnson Controls Unitary Products
19
Subject to change without notice. Printed in U.S.A.
Copyright © 2008 by Johnson Controls, Inc. All rights reserved.
Johnson Controls Unitary Products
5005 York Drive
Norman, OK 73069
268709-YIM-C-0908
Supersedes: 268709-YIM-B-0807
Download PDF