advertisement
Product Category
TLM 100T • Installation Guide
The TLM 100T is a secure tabletop mounting enclosure for an iPad ® in a landscape orientation. The enclosure is compatible with the iPad 2, iPad 3, and iPad 4.
Installing an iPad in a TLM 100T
1. Use the provided Extron removal tool to ease the faceplate away from the back panel. Start by releasing the catches at the bottom and gradually work around the sides until the faceplate lifts off.
2.
3.
4.
Remove the metal frame.
Remove the base cover, using the Extron removal tool.
Run the iPad charging cable through the hole at the bottom of the TLM 100T back panel, then through the cable raceway in the base of the unit, and out the back of the base.
NOTE:
Leave about 1½ inches (3.8 cm) of charging cable free to connect to the iPad.
1 8
5.
6.
7.
Place the iPad in the rear enclosure. The power switch must be in the top left corner.
Place the metal frame with the rubber pads in contact with the iPad.
Use the provided #6 spanner bit and the eight provided spanner drive screws to secure the metal frame.
ATTENTION:
Do not overtighten the screws.
8.
9.
Replace the faceplate. Ensure it is in the correct orientation with the
Extron name at the bottom.
Replace the TLM 100T base cover.
Power Switch
2 6
5
7
Spanner Drive Screws (8) secure the metal frame to the TLM 100T back panel.
TLM 100T Faceplate snaps to unit (11 plcs.)
4
3 iPad
TLM 100T
Back Panel.
Tabletop Mounting Options
TLP 100T rear view with the base cover removed.
Securing the TLM 100T to a Tabletop
The TLM 100T can stand on any convenient tabletop. If required, use two screws in the two mounting holes in the base to secure the unit to the desktop (see the figure at right).
1.
2.
Drill two holes through the desktop. The two holes must be 3.07 inches (78 mm) apart and 3/8 inch (9.5 mm) in diameter.
Fasten the base to the desktop with two #8 wood screws (not provided) through the desktop from underneath into the two holes in the base of the TLM 100T.
Installing the TLM 100T on an SMA-1 Swivel Mount
The TLM 100T can be mounted with the Extron SMA-1 swivel mount adapter, allowing it to swivel up to 359° (see the SMA-1 Swivel Mount Adapter Kit User Guide at www.extron.com
).
1.
2.
3.
4.
Determine where the SMA-1 and TLM 100T are to be mounted.
Mount the SMA-1 and configure the set screws as described in the SMA-1
Swivel Mount Adapter Kit User Guide.
Remove the rear and base covers of the TLM 100T, using the Extron removal tool.
Remove the hole plug from the base of the TLM 100T to reveal the mounting hole.
TLP 100T Base View
Mounting Holes for screws (2)
Hole Plug for
SMA-1 mounting
1
5.
6.
7.
Place the base over the conduit of the SMA-1.
Secure the TLM 100T with the backing plate and locking nut of the SMA-1.
Replace the base and rear covers.
Securing the TLM 100T with a Kensington Lock
For additional security, attach a Kensington Security Lock (not provided) to the metal-reinforced slot at the rear edge of the base (see the figure at right), following the instructions provided by the manufacturer.
Power Switch
Rear Cover
Wall Mounting Options
ATTENTION:
Do not install the iPad until after the
TLM 100T has been mounted.
The TLM 100T can be mounted using a VESA adapter or to a junction box. For either of these options, the TLM 100T base and rear covers must be removed.
Preparation: Removing the TLM 100T Base
1. Remove the base cover.
2.
3.
4.
Remove the rear cover.
If required, remove the rear enclosure knock-out to route the iPad cable.
Remove the four screws holding the hinges to the rear enclosure (see diagram at right).
VESA-Mounting
The TLM 100T can be VESA mounted using, for example, the Extron LPVM-1.
1.
2.
3.
4.
Run the iPad charging cable through the knock-out or the hole at the bottom of the rear enclosure.
Locate the four VESA mount holes, marked M4.
Follow the instructions of the manufacturer to mount the TLM 100T.
Install the iPad as described in “Installing an iPad in a TLM 100T” on the previous page.
TLM 100T Rear Panel (exterior)
Mounting to a Junction Box
The TLM 100T can be mounted directly to a junction box.
1.
2.
3.
4.
Run the iPad charging cable through the knock-out or the hole at the bottom of the rear enclosure.
Locate the appropriate holes, using the figure at right.
Mount the TLM 100T with the appropriate screws (not provided)
Install the iPad as described in “Installing an iPad in a TLM 100T” on the previous page.
2G
1G
EU/MK
2G
Speaker Cover
Notch to Remove
Rear Cover
Base Cover
Notch to Remove
Base Cover
Slot for Kensington Lock
1G
1G
VESA Mounting Holes (4)
Cable Knock-out
Hinges (4)
2G
1G
EU/MK
2G
Changing the Front Faceplate
The TLM 100T is shipped with a faceplate that allows access to the iPad home button and the front facing camera. The TLM 100A, which must be purchased separately, is an alternative faceplate for users that do not need access to these features. To install the TLM 100A:
1.
2.
Remove the existing faceplate using the Extron removal tool.
Clip the TLM 100A into place.
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
(Inside Asia Only)
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+4000.398766
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
2
© 2012 Extron Electronics All rights reserved. www.extron.com
TLM 100T Rear Panel (interior)
1G = EU or MK Junction Box
2G = US Junction Box
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
Inside India Only
+91.80.3055.3777
+91.80.3055.3737 FAX
68-2322-50 Rev. A
11 12
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 TLM 100T Installation Guide
- 1 Installing an iPad in a TLM 100T
- 1 Tabletop Mounting Options
- 1 Securing the TLM 100T to a Tabletop
- 1 Installing the TLM 100T on an SMA-1 Swivel Mount
- 2 Securing the TLM 100T with a Kensington Lock
- 2 Wall Mounting Options
- 2 Preparation: Removing the TLM 100T Base
- 2 VESA-Mounting
- 2 Mounting to a Junction Box
- 2 Changing the Front Faceplate
- 2 Extron Contact Information