Avital | 4200 | Installation guide | Avital 4200 Installation guide

Model 4200
Installation Guide
NOTE: This product is intended for installation by a professional installer only!
Any attempt to install this product by any person other than a trained professional
may result in severe damage to a vehicle’s electrical system and components.
© 2004 Directed Electronics, Inc. Vista, CA
N832002 06-04
table of contents
warning! safety first . . . . . . . . . . . . . . . . . . . . . 3
installation points to remember . . . . . . . . . . . . . 4
before beginning the installation. . . . . . . . . . 4
after the installation . . . . . . . . . . . . . . . . . . 4
deciding on component locations . . . . . . . . . . . . 4
control module . . . . . . . . . . . . . . . . . . . . . . 4
valet/program switch . . . . . . . . . . . . . . . . . . 5
status LED . . . . . . . . . . . . . . . . . . . . . . . . . 5
optional starter kill relay . . . . . . . . . . . . . . . 6
finding the wires you need . . . . . . . . . . . . . . . . . 6
obtaining constant 12V . . . . . . . . . . . . . . . . 6
finding the 12V switched ignition wire . . . . . . 7
finding the starter wire . . . . . . . . . . . . . . . . 7
finding a (+) brake light wire . . . . . . . . . . . . 8
finding the accessory/heater wire . . . . . . . . . 8
finding the RPM input wire . . . . . . . . . . . . . . 9
finding the wait-to-start bulb wire for diesels . 9
wiring diagrams . . . . . . . . . . . . . . . . . . . . . . . 10
primary harness (H1) wiring diagram . . . . . . 10
remote start ribbon harness wiring diagram . . 11
heavy gauge relay satellite wiring diagram . . 11
auxiliary harness (H2) wiring diagram . . . . . . 12
remote start harness (H3) wiring diagram . . . 12
door lock harness (H4) wiring diagram . . . . . 12
remote start auxiliary harness wiring diagram 12
primary harness (H1) wire connection guide . . . . 13
relay key switch interface wire connection guide . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
auxiliary harness (H2) wire connection guide . . . 18
remote start harness (H3) wire connection guide . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
neutral safety switch interface . . . . . . . . . . . . . 21
testing the neutral safety switch . . . . . . . . . 22
The Bitwriter® (p/n 998T)
requires chip version 1.5 or
newer to program this unit.
2
1995 and newer vehicle anti-theft systems (immobi lizers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
passlock I and passlock II (PL-1 and PL-2) . . 24
passkey III (PK-3), transponder-based systems .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
bypassing GM vehicle anti-theft systems . . . . . . .
(VATS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
plug-in LED and valet/program switch . . . . . . . . 26
programmer interface, 3-pin port . . . . . . . . . . . . 26
programming jumpers . . . . . . . . . . . . . . . . . . . 27
light flash (+)/(-) . . . . . . . . . . . . . . . . . . . 27
tach threshold on/off . . . . . . . . . . . . . . . . . 27
transmitter/receiver learn routine . . . . . . . . . . . 28
transmitter configurations . . . . . . . . . . . . . . . . 30
button configuration . . . . . . . . . . . . . . . . . 30
operating settings learn routine . . . . . . . . . . . . 30
feature menus . . . . . . . . . . . . . . . . . . . . . . . . . 32
menu #1. . . . . . . . . . . . . . . . . . . . . . . . . . 32
menu #2. . . . . . . . . . . . . . . . . . . . . . . . . . 33
feature descriptions . . . . . . . . . . . . . . . . . . . . . 34
menu #1. . . . . . . . . . . . . . . . . . . . . . . . . . 34
menu #2. . . . . . . . . . . . . . . . . . . . . . . . . . 36
tach learning . . . . . . . . . . . . . . . . . . . . . . . . . 37
shutdown diagnostics . . . . . . . . . . . . . . . . . . . 38
rapid resume logic . . . . . . . . . . . . . . . . . . . . . . 39
timer mode . . . . . . . . . . . . . . . . . . . . . . . . . . 39
valet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
safety check . . . . . . . . . . . . . . . . . . . . . . . . . . 40
troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 41
wiring quick reference guide . . . . . . . . . . . . . . . 43
relay satellite wiring quick reference guide . . . . . 44
Bitwriter™, Code Hopping™, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn
Routine™, Nite-Lite®, Nuisance Prevention Circuitry®, NPC®, Revenger®, Silent
Mode™, Soft Chirp®, Stinger®, Valet®, Vehicle Recovery System®, VRS®, and Warn
Away® are all Trademarks or Registered Trademarks of Directed Electronics, Inc.
© 2004 Directed Electronics, Inc. Vista, CA
warning! safety first
The following safety warnings must be observed at all times:
■ Due to the complexity of this system, installation of this product must only be performed by an authorized
Directed dealer.
■ When properly installed, this system can start the vehicle via a command signal from the remote control
transmitter. Therefore, never operate the system in an area that does not have adequate ventilation. The following precautions are the sole responsibility of the user; however, authorized Directed dealers should make
the following recommendations to all users of this system:
1. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).
2. When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote
start system must be disabled using the installed toggle switch.
3. It is the user's sole responsibility to properly handle and keep out of reach from children all remote
control transmitters to assure that the system does not unintentionally remote start the vehicle.
4. THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO
T HE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY
ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED.
■ Use of this product in a manner contrary to its intended mode of operation may result in property damage,
personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1)
Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the
keys in the ignition. The user will be responsible for having the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be
performed by an authorized Directed Electronics dealer in accordance with the Safety Check outlined in this
product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult
with the user to fix the problem immediately.
■ After the remote start module has been installed, test the remote start module in accordance with the Safety
Check outlined in this installation guide. If the vehicle starts when performing the Neutral Safety Shutdown
Circuit test, the remote start unit has not been properly installed. The remote start module must be removed
or properly reinstalled so that the vehicle does not start in gear. All installations must be performed by an
authorized Directed Electronics dealer. OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN
GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER
THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE
OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED ELECTRONICS,
INC. WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.
© 2004 Directed Electronics, Inc. Vista, CA
3
installation points to remember
before beginning the installation
IMPORTANT! This product is designed for fuel-injected, automatic transmission vehicles only.
Installing it in a standard transmission vehicle is dangerous and is contrary to its intended use.
■ Please read this entire installation guide before beginning the installation. The installation of this remote
start system requires interfacing with many of the vehicle’s systems. Many new vehicles use low-voltage or
multiplexed systems that can be damaged by low resistance testing devices, such as test lights and logic
probes (computer safe test lights). Test all circuits with a high quality digital multi-meter before making connections.
■ Do not disconnect the battery if the vehicle has an anti-theft-coded radio. If equipped with an air bag, avoid
disconnecting the battery if possible. Many airbag systems will display a diagnostic code through their
warning lights after they lose power. Disconnecting the battery requires this code to be erased, which can
require a trip to the dealer.
■ Remove the domelight fuse. This prevents accidentally draining the battery.
■ Roll down a window to avoid being locked out of the car.
after the installation
■ Test all functions. The "Using Your System" section of the Owner's Guide is very helpful when testing.
■ Complete the vehicle Safety Check outlined in this manual prior to the vehicle reassembly.
deciding on component locations
control module
Things to remember when positioning the control module:
■ Never place the control module in the engine compartment!
■ The first thing a thief will do when hot-wiring a vehicle is to remove the driver's side under-dash panel to
access the starter and ignition wires. You should therefore avoid placing the control module just behind the
driver’s side dash to prevent it from being easily disconnected during a theft attempt.
■ When locating the control module, try to find a secure location that will not require you to extend the harness
wires (they are 1.5 meters long).
4
© 2004 Directed Electronics, Inc. Vista, CA
■ Keep the control module away from the heater core (or any other heat sources) and any obvious leaks.
■ The higher the control module is in the vehicle, the better the transmitter range will be. Some good control
module locations: Above the glove box, inside the center console, above the under-dash fuse box, or above
the radio.
valet/program switch
Ensure that the location you pick for this switch has sufficient clearance to the rear. The switch should be well
hidden. It should be placed so that passengers or stored items (such as items placed in a glove box or center
console) cannot accidentally bump it. The switch fits in a 9/32-inch hole.
IMPORTANT! When the vehicle is delivered, please show the user where the Valet®/Program
switch is located and how to disarm the system using the switch.
status LED
Things to remember when positioning the status LED:
■ It should be visible from both sides and the rear of the vehicle, if possible.
■ It needs at least 1/2-inch clearance to the rear.
■ It is easiest to use a small removable panel, such as a switch blank or a dash bezel. Remove it before drilling
your 9/32-inch hole.
■ Use quick-disconnects near the LED wires if the panel is removable. This lets mechanics or other installers
remove the panel without having to cut the wires.
© 2004 Directed Electronics, Inc. Vista, CA
5
optional starter kill relay
If the optional starter kill relay or its connections are immediately visible upon removal of the under-dash panel,
they can easily be bypassed. Always make the relay and its connections difficult to discern from the factory
wiring! Exposed yellow butt connectors do not look like factory parts, and will not fool anyone! For this reason,
routing the starter kill wires away from the steering column is recommended.
finding the wires you need
Now that you have determined where each component will be located, your next step is to find the wires in the
vehicle that the security system will be connected to.
IMPORTANT! Do not use a 12V test light to locate these wires! All testing described in this
manual assumes the use of a digital multimeter.
obtaining constant 12V
We recommend two possible sources for 12V constant: The (+) terminal of the battery, or the constant 12V supply
to the ignition switch. Always install a fuse within 12 inches of this connection. If the fuse will also be powering other circuits, such as door locks, a power window module, or a Nite-Lite® headlight control system, fuse
accordingly.
IMPORTANT! Do not remove the fuse holder on the red wire. It ensures that the control module
has its own fuse, of the proper value, regardless of how many accessories are added to the main
power feed.
6
© 2004 Directed Electronics, Inc. Vista, CA
finding the 12V switched ignition wire
The ignition wire is powered when the key is in the run or start position. This is because the ignition wire powers
the ignition system (spark plugs, coil) as well as the fuel delivery system (fuel pump, fuel injection computer).
Accessory wires lose power when the key is in the start position to make more current available to the starter motor.
How to find (+)12V ignition with your multimeter:
1. Set to DCV or DC voltage (12V or 20V is fine).
2. Attach the (-) probe of the meter to chassis ground.
3. Probe the wire you suspect of being the ignition wire. The steering
column harness or ignition switch harness is an excellent place to find
this wire.
4. Turn the ignition key switch to the run position. If your meter reads
(+)12V, go to the next step. If it does not read (+)12V, probe another wire.
5. Now turn the key to the start position. The meter display should stay steady, not dropping by more than a
few tenths of a volt. If it drops close to or all the way to zero, go back to Step 3. If it stays steady at (+)12V,
you have found an ignition wire.
finding the starter wire
The starter wire provides 12V directly to the starter or to a relay controlling starter. In some vehicles, it is
necessary to power a cold start circuit. A cold start circuit will test exactly like a starter circuit, but it does not
control the starter. Instead, the cold start circuit is used to prime the fuel injection system for starting when the
vehicle is cold.
© 2004 Directed Electronics, Inc. Vista, CA
7
How to find the starter wire with your multimeter:
1. Set to DCV or DC voltage (12V or 20V is fine).
2. Attach the (-) probe of the meter to chassis ground.
3. Probe the wire you suspect of being the starter wire. The steering
column is an excellent place to find this wire. Remember you do not
need to interrupt the starter at the same point you test it. Hiding your
optional starter kill relay and connections is always recommended.
4. Turn the ignition key switch to the start position. Make sure the car is
not in gear! If your meter reads (+)12V, go to the next step. If it doesn’t, probe another wire.
5. Cut the wire you suspect of being the starter wire.
6. Attempt to start the car. If the starter engages, reconnect it and go back to Step 3. If the starter does not
turn over, you have the right wire.
finding a (+) brake light wire
Most vehicles use a (+) brake light circuit. The (+) brake light wire is often found near the brake pedal. The same
wire can often be accessed in the kick panel or running board.
How to find a (+) brake light wire with your multimeter:
1. Set to DCV or DC voltage (12V or 20V is fine).
2. Attach the (-) probe of the meter to chassis ground.
3. Probe the wire you suspect of being the brake light wire.
4. Press the brake pedal. If your meter shows (+)12V, release the brake pedal and make sure it goes back to
zero.
5. If it does return to zero, this is the correct brake wire.
finding the accessory/heater wire
An accessory/heater wire will show +12V when the key is in the accessory and run positions. It will not show
+12V during the cranking cycle. There will often be more than one accessory wire in the ignition harness. The
correct accessory wire will power the vehicle's climate control system. Some vehicles may have separate wires for
the blower motor and the air conditioning compressor. In such cases, it will be necessary to add a relay to power
the second accessory wire.
8
© 2004 Directed Electronics, Inc. Vista, CA
finding the RPM input wire
To test for a tachometer wire, a multimeter capable of testing AC voltage must be used. The tachometer wire will
show between 1V and 6V AC. In multi-coil ignition systems, the system can learn individual coil wires. Individual
coil wires in a multi-coil ignition system will register lower amounts of AC voltage. Also, if necessary, the system
can use a fuel injector control wire for engine speed sensing. Common locations for a tachometer wire are the
ignition coil itself, the back of the gauges, engine computers, and automatic transmission computers.
IMPORTANT! Do not test tachometer wires with a test light or logic probe. The vehicle will be
damaged.
How to find a tachometer wire with your multimeter:
1. Set to ACV or AC voltage (12V or 20V is fine).
2. Attach the (-) probe of the meter to chassis ground.
3. Start and run the vehicle.
4. Probe the wire you suspect of being the tachometer wire with the red probe of the meter.
5. If this is the correct wire the meter will fluctuate with the rpm of the motor and read between 1V and 6V.
finding the wait-to-start bulb wire for diesels
In diesel vehicles it is necessary to interface with the wire that turns on the WAIT TO START light in the dashboard. This wire illuminates the bulb until the vehicle’s glow plugs are properly heated. When the light goes out
the vehicle can be started. This wire is always available at the connector leading to the bulb in the dashboard.
It can also be found at the Engine Control Module (ECM) in many vehicles.
To test and determine the polarity of this wire:
1. Set your multimeter to DCV or DC voltage (12 or 20V is fine).
2. Attach the (+) probe of the meter to (+)12V.
3. Probe the wire that you suspect leads to the bulb with the (-) probe of the meter.
4. Turn the ignition switch to the ON position.
5. If the meter indicates 12 volts until the light goes out you have isolated the correct wire and the wire's polarity is negative (ground while the bulb is on).
6. If the meter reads zero volts until the light goes out and then reads 12 volts, you have isolated the correct
wire and the wire's polarity is positive.
© 2004 Directed Electronics, Inc. Vista, CA
9
wiring diagrams
primary harness (H1) wiring diagram
The primary harness supplied with this unit is the standard 12-pin harness used by Directed Electronics, Inc.
security systems. Three wires in the plug are not used. The upgrade from this unit to a security system would
simply require unplugging and exchanging control units and connecting the necessary wires to the vehicle. The
functions of all the wires that are used in the primary harness are outlined in the following wiring diagram and
the wire connections are described in the wire connection guides.
H1/1
H1/2
H1/3
______
______
______
H1/4 ______
ORANGE
WHITE
WHITE/BLUE
BLACK/WHITE
H1/5 ______
H1/6 ______
BLUE
(-) REMOTE START ACTIVATION INPUT
(-)200 mA DOMELIGHT SUPERVISION OUTPUT
(-) SECOND UNLOCK OUTPUT
NO FUNCTION
BLACK
H1/9 ______
10
(+)/(-) SELECTABLE LIGHT FLASH OUTPUT
NO FUNCTION
H1/7 ______
H1/8 ______
(-) 500 mA ARMED OUTPUT
(-) CHASSIS GROUND INPUT
NO FUNCTION
H1/10 ______
BROWN
H1/11 ______
RED
H1/12 ______
RED/WHITE
(-) HORN HONK OUTPUT
(+) CONSTANT POWER INPUT
(-)200 mA CHANNEL 2 VALIDITY OUTPUT
© 2004 Directed Electronics, Inc. Vista, CA
remote start ribbon harness wiring diagram
1
______
2
______
3
______
4
______
5
______
6
______
7
______
PINK/WHITE
YELLOW
PINK
(-) 200 mA PROGRAMMABLE ACC/IGN OUTPUT
(+) IGNITION INPUT TO REMOTE START
(-) 200 mA IGNITION RELAY TURN-ON
ORANGE
(-) 200 mA ACCESSORY RELAY TURN-ON
PURPLE
(-) 200 mA STARTER RELAY TURN-ON
ORANGE/BLACK
BLUE
(-) ANTI-GRIND OUTPUT/GROUND WHEN ARMED OUTPUT
(-) 200 mA STATUS OUTPUT
heavy gauge relay satellite wiring diagram
1
______
2
______
3
______
4
______
5
______
6
______
7
______
8
______
PURPLE
GREEN
RED
ORANGE
RED
PINK
RED/WHITE
PINK/WHITE
© 2004 Directed Electronics, Inc. Vista, CA
(+) STARTER OUTPUT TO STARTER (STARTER SIDE)
STARTER INPUT FROM IGNITION (KEY SIDE)
(+) (30A) HIGH CURRENT 12V INPUT
(+) OUTPUT TO ACCESSORY CIRCUIT
(+) (30A) HIGH CURRENT 12V INPUT
(+) OUTPUT TO IGNITION CIRCUIT
HIGH CURRENT 12V INPUT
(+) OUTPUT TO SECOND IGNITION/ACCESSORY CIRCUIT
11
auxiliary harness (H2) wiring diagram
H2/1
H2/2
H2/3
H2/4
______
______
______
______
VIOLET/BLACK
(-) CHANNEL 4 OUTPUT
GREEN/WHITE
(-) FACTORY REARM OUTPUT
GRAY/BLACK
(-) WAIT-TO-START INPUT
LIGHT GREEN/BLACK
(-) FACTORY DISARM
remote start harness (H3) wiring diagram
H3/1
H3/2
H3/3
______
______
______
BLUE/WHITE
(-) 200 mA 2ND STATUS/REAR DEFOGGER - LATCHED/PULSED
GRAY
BROWN
(-) HOOD PINSWITCH SHUTDOWN WIRE
(+) BRAKE SWITCH SHUTDOWN WIRE
H3/4 ______
VIOLET/WHITE
TACHOMETER INPUT WIRE
H3/5 ______
BLACK/WHITE
(-) NEUTRAL SAFETY SWITCH INPUT
door lock harness (H4) wiring diagram
H4/1 ______
GREEN
H4/2 ______
H4/3 ______
(-) LOCK (+) UNLOCK
NO FUNCTION
BLUE
(+) LOCK (-) UNLOCK
remote start auxiliary harness wiring diagram
12
1
______
2
______
3
______
4
______
BLUE
ORANGE
PINK
PURPLE
(-) 200 mA STATUS OUTPUT
(-) 200 mA ACCESSORY RELAY TRIGGER
(-) 200 mA IGNITION RELAY TRIGGER
(-) 200 mA STARTER RELAY TRIGGER
© 2004 Directed Electronics, Inc. Vista, CA
primary harness (H1) wire connection guide
H1/1 ORANGE (-) ground-when-armed output
This wire supplies a (-)500 mA ground as long as the system is armed. This output ceases as soon as the system
is disarmed. The orange wire may be wired to an optional Directed Electronics, Inc. 8618 starter kill relay.
H1/2 WHITE (+/-) selectable light flash output
As shipped, this wire should be connected to the (+) parking light wire. If the light flash polarity jumper is moved
to the opposite position (see Internal Programming Jumpers section), this wire supplies a (-)200 mA output.
This is available for driving (-) light control wires in Toyota, Lexus, BMW, some Mitsubishi, some Mazda, and
various other models.
(+) Positive Light Flash Output
(-) Light Flash Output
NOTE: For parking light circuits that draw 10 amps or more, the internal jumper must be switched
to a (-) light flash output. (See the Internal Programming Jumper section of this guide.) P/N
8617 or a standard automotive SPDT relay must be used on the H1/2 light flash output harness
wire.
© 2004 Directed Electronics, Inc. Vista, CA
13
H1/3 WHITE/BLUE (-) remote start activation input
This input comes from the factory set to 2 activation pulses. This means that it is necessary to have 2 consecutive ground pulses on the white/blue wire for the remote start to activate or to deactivate. The same holds true
for the remote control activation when set to a two pulse setting it is necessary to press the
button twice
for the remote start to activate or deactivate.
NOTE: When the activation pulse count can be programmed to 1, 2, or 3 pulses when changed
it will affect both activation inputs; the White/Blue wire and the remote control activation.
H1/4 BLACK /WHITE (-) 200 mA domelight supervision output
Connect this wire to the optional domelight supervision relay as shown below:
IMPORTANT! This output is only intended to drive a relay. It cannot be connected directly to the
domelight circuit because the output cannot support the current draw of one or more light
bulbs.
H1/6 BLUE second unlock
This output is used for progressive door unlock. A progressive unlock system unlocks the driver's door when the
unlock (disarm) button is pressed and unlocks the passenger doors if the unlock (disarm) button is pressed again
14
© 2004 Directed Electronics, Inc. Vista, CA
within 15 seconds after unlocking the driver's door. The BLUE wire outputs a low current (-) pulse on the second
press of the unlock button of the transmitter. This negative unlock output is used to unlock the passenger doors.
NOTE: The second unlock output feature is not available if the double pulse unlock feature
is turned on.
H1/8 BLACK (-) chassis ground connection
Remove any paint and connect this wire to bare metal, preferably with a factory bolt rather than your own screw.
(Screws tend to either strip or loosen with time.) We recommend grounding all your components, including the
siren, to the same point in the vehicle.
H1/10 BROWN (-) horn honk output
This wire supplies a (-) 200 mA output that can be used to honk the vehicle horn. It outputs a single pulse when
locking the doors with the remote, and two pulses when unlocking with the remote. This wire will also output
pulses for 30 seconds when the Panic Mode is activated. If the vehicle has a (+) horn circuit, an optional relay
can be used to interface with the system, as shown below.
© 2004 Directed Electronics, Inc. Vista, CA
15
H1/11 RED (+)12V constant power input
Before connecting this wire, remove the supplied fuse. Connect to the battery positive terminal or the constant
12V supply to the ignition switch.
NOTE: Always use a fuse within 12 inches of the point you obtain (+)12V. Do not use the 10A
fuse in the harness for this purpose. This fuse is intended to protect the module.
H1/12 RED/WHITE Channel 2, (-) 200 mA output
When the system receives the code controlling Channel 2, for longer than 1.5 seconds, the RED/WHITE wire will
supply an output as long as the transmission continues. This is often used to operate a trunk/hatch release or
other relay-driven function.
IMPORTANT! Never use this wire to drive anything except a relay or low-current input! The transistorized output
can only supply 200 mA of current. Connecting directly to a solenoid, motor, or other high-current device will
cause it to fail.
16
© 2004 Directed Electronics, Inc. Vista, CA
relay key switch interface wire
connection guide
All except the red heavy gauge wires leading from the relay satellite are used to energize high current circuits in
the vehicle. It is crucial that these connections are made correctly so that they are capable of handling the
current demands. For this reason, scotch locks, T-taps and other such connectors should not be used.
PURPLE (+) starter output
After cutting the starter wire connect the PURPLE wire to the end going to the starter motor.
GREEN starter kill
After cutting the starter wire connect the GREEN wire to the end going to the key side of the ignition.
RED (2) (+)12V input for relays
Remove the two 30 amp fuses prior to connecting these wires and do not replace them until the satellite has
been plugged into the control module. These wires are the source of current for all the circuits the relay satellite
will energize. They must be connected to a high current source. Since the factory supplies (+) 12V to the key
switch that is used to operate the motor, it is recommended that these wires be connected there.
NOTE: If the factory supplies two separate (+) 12V feeds to the ignition switch, connect one RED
wire of the satellite to each feed at the switch.
ORANGE (+) accessory output
Connect this wire to the accessory wire in the vehicle that powers the climate control system.
PINK (+) ignition output
Connect this wire to the ignition wire in the vehicle.
PINK/WHITE (+) output to second ignition/accessory circuit
Connect this wire to the second ignition or accessory wire in the vehicle (selectable menu feature 2-9).
RED/WHITE 12 V input
If additional current capacity is needed cut this wire, add a fuse adequate for the circuit to be supplied, and
connect to an additional 12V source.
© 2004 Directed Electronics, Inc. Vista, CA
17
auxiliary harness (H2) wire connection guide
H2/1 VIOLET/BLACK (-) channel 4 output
This wire provides 200 mA programmable output. (See Feature Descriptions section of this guide.)
H2/2 GREEN/WHITE factory rearm output
This wire sends a negative pulse every time the remote start shuts down or the doors are locked. This can be
used to pulse the arm wire of the vehicle's factory anti-theft device. Use a relay to send a (-) or (+) pulse to the
arm wire.
H2/3 GRAY/BLACK (-) diesel wait-to-start bulb input
Connect this wire to the wire in the vehicle that sends the signal to turn on the WAIT-TO-START bulb in the dashboard. In most diesels the wire is negative (ground turns on the bulb) and the GRAY/BLACK can be directly
connected to the wire in the vehicle. If the vehicle uses a positive wire (12V to turn on the bulb) a relay must
be used to change the polarity. (See Finding the Wait-To-Start Bulb Wire For Diesels section of this guide.) Here
are some common colors of this wire:
■ Chevrolet and GMC trucks: Light Blue or Dark Blue
■ Ford Trucks: Black/Pink
■ Dodge Ram Trucks: Orange/Black or Black/Orange
NOTE! A 1-amp diode must be installed in line on the factory wire between the wait-to-start
indicator and the ECM. (See the following diagram for details.)
18
© 2004 Directed Electronics, Inc. Vista, CA
H2/4 LIGHT GREEN/BLACK (-) auxiliary output
This wire sends a negative pulse every time the remote start is activated or the doors are unlocked. This can be
used to pulse the disarm wire of the vehicle's factory anti-theft device. Use a relay to send a (-) or (+) pulse to
the disarm wire as shown in the following diagrams.
Relay for Negative (-) Disarm Wire
© 2004 Directed Electronics, Inc. Vista, CA
Relay for Positive (+) Disarm Wire
19
remote start harness (H3) wire connection guide
H3/1 BLUE/WHITE status/defogger output
This wire supplies a 200mA output as soon as the module begins the remote start process. The H3/1 BLUE wire
can also be used to activate the defogger trigger (latched/pulsed) 10-seconds after the remote start engages.
(See the Feature Descriptions section in this guide for details about programming this output.)
H3/3 GRAY (-) hood pinswitch input
This wire MUST be connected to hood pinswitch. This input will disable or shut down the remote start when the hood
is opened.
H3/4 BROWN (+) brake switch input
This wire MUST be connected to the vehicle's brake light wire. This is the wire that shows (+) 12V when the brake
pedal is pressed. The remote start will be disabled or shut down any time the brake pedal is pressed.
H3/5 VIOLET/WHITE tachometer input
This input provides the module with information about the engine's revolutions per minute (RPMs). It can be
connected to the negative side of the coil in vehicles with conventional coils. In multi-coil and high energy ignition systems locating a proper signal may be more difficult. (See Installation Points to Remember section of this
guide for finding the tachometer wire.) Once connected, you must teach the system the tach signal. (See Tach
Learning section of this guide.)
H3/6 BLACK/WHITE neutral safety switch input
Connect this wire to the toggle (override) switch as shown in Figure A. Connect the other wire from the toggle
switch to the PARK/NEUTRAL switch in the vehicle. This wire will test with ground with the gear selector either
in PARK or NEUTRAL. This will prevent the vehicle from accidentally being started while in a drive gear. This input
MUST rest at ground in order for the remote start system to operate. Connected properly the vehicle will only
start while in PARK or NEUTRAL.
In some vehicles, the PARK/NEUTRAL position switch activates a factory starter lock out that will not allow the
starter to operate in a drive gear. In these vehicles, connect this wire to the toggle switch as shown in Figure
B. Connect the other wire from the toggle switch to chassis ground.
20
© 2004 Directed Electronics, Inc. Vista, CA
Figure A
Figure B
IMPORTANT! Always perform the Vehicle Safety Check section of this guide to verify that the
vehicle cannot be started in ANY drive gear and that the override switch is functioning properly.
neutral safety switch interface
Some vehicles combine the column shift mechanism and the mechanical neutral safety switch into one mechanical part. In these vehicles, it is impossible to interface the remote start system before the neutral safety switch.
With this type of vehicle, if the vehicle is left in a drive gear and the remote start system is activated, the vehicle
will move and may cause damage to persons or property.
According to available information, vehicles known to be manufactured this way are most General Motors trucks,
sport utility vehicles and column shifting passenger vehicles. Available information also indicates that pre-1996
Dodge Dakota pickups with 2.5 liter motors are also manufactured this way.
GM vehicles that have the neutral safety switch built into the column shifter can usually be identified by a purple
starter wire. Typically, vehicles that use an outboard mechanical switch use a yellow wire from the ignition switch
to the mechanical switch and a purple wire from the mechanical switch to the starter itself. Remember, this is
only a rule of thumb and is not intended as a substitute for proper testing.
We suggest the following procedure to test for vehicles manufactured in this way.
NOTE: You must complete the remote start system installation before doing the following test.
Ensure that the remote start system is functioning normally. This includes connecting to the
brake as a shut-down.
© 2004 Directed Electronics, Inc. Vista, CA
21
testing the neutral safety switch
1. Make sure there is adequate clearance to the front and rear of the vehicle because it may move slightly.
2. Make sure the hood is closed and there are no remote start shut-downs active.
3. Set the emergency brake.
4. Turn the key to the "run" position, this will release the shifter.
5. Place the car in drive (D).
6. Place your foot directly over the brake pedal, but do not depress it. Be ready to step on the brake if the
starter engages.
7. Activate the remote start system.
8. If the starter engages, immediately depress the brake to shut the remote start system down. If the starter
does not engage, no additional safety system is required.
If the starter engages and the vehicle is a General Motors product or Dodge Dakota pickup, refer to the following text and diagrams for an alternative shut-down method which will prevent the starter from engaging. If the
vehicle is not a General Motors product or a Dodge Dakota pickup, please call Directed Electronics, Inc. Technical
Support for an alternative shut-down method. Do not return the vehicle to the customer until this feature is properly installed!
Every vehicle built this way requires that the shifter be placed in park to remove the keys from the ignition. As
a result, it is possible to use the key-in-ignition sense switch to prevent remote starting if the keys are in the
ignition. The diagrams in this section illustrate how to accomplish this.
Diagram A applies to all General Motors vehicles at the time of publication of this guide. Diagram B applies to
all pre-1996 Dodge Dakota pickup trucks with 2.5 liter motors. This solution has one side effect - if the customer
inserts the key in the ignition with the driver's door open, the remote start system will shut down. If this interface is used it is important to inform the customer to close the driver’s door before inserting the key into the
ignition when the remote start is active. This will allow the customer to turn the key on and shut the remote
start down by pressing the brake without the key sense wire shutting down the unit prematurely.
In addition, you must connect a tan (+) shut-down input to the yellow wire on the relay satellite ribbon cable.
This prevents the remote start system from activating if the key is left in the "run" position. If your remote start
system only has one tan input, you must use diodes to isolate the ignition circuit from the brake switch input.
However, due to future manufacturer changes in vehicles, it is possible that this may not apply to all vehicles.
In addition, color variations are possible from model to model; make sure to test the circuit carefully. Please call
Directed Electronics, Inc. Technical Support if you need assistance in making this interface.
IMPORTANT! Once the interface is complete, attempt to remote start the vehicle with the
door closed and the key in the ignition. The vehicle should not start. If it does, recheck the
connections.
22
© 2004 Directed Electronics, Inc. Vista, CA
Diagram A - General Motors trucks, sport utility vehicles and column shifting passenger vehicles:
Diagram B - Pre-1996 Dodge Dakota pickups with 2.5 liter motors:
© 2004 Directed Electronics, Inc. Vista, CA
23
1995 and newer vehicle anti-theft systems
(immobilizers)
1995 and newer vehicle anti-theft systems (immobilizers) require a bypass module. The bypass module allows for
easy interfacing, while still maintaining the OEM system’s integrity.
passlock I and passlock II (PL-1 and PL-2)
The Passlock I and Passlock II systems can be found in the following General Motors vehicles:
■ ‘95 and newer Cavalier and Sunfire
■ ‘96 and newer Achieva, Grand Am, and Skylark
■ ‘97 and newer Intrigue, Malibu, and Cutlass
■ ‘98 and newer trucks, vans, SUVs
■ ‘99 and newer Alero
■ 2000 and newer Impala and Saturn
Passlock I and II systems are VATS-evolved. Passlock systems still rely on the R-code to start, but the pellet is no
longer placed in the key. The resistor can now be found in the key switch. This allows for a greater number of
possible R-codes. In addition, Passlock systems require “seeing” the correct R-code at the correct time. To bypass
Passlock I and II, p/n 555L or p/n 555T is required.
passkey III (PK-3), transponder-based systems
The Passkey III system can be found in the following vehicles:
■ ‘97 and newer Park Avenue
■ ‘98 and newer Cadillac
■ ‘99 and newer U vans, Transport, Montana, and Silhouette
■ 2000 and newer Grand Prix, Lesabre, Monte Carlo, Lumina, Bonneville
■ 2001 and newer Aurora, Aztek and Rendezvous
Other transponder-based systems include: Acura, BMW, Dodge/Chrysler/Jeep, Ford, Honda, Infinity, Mazda,
Mercedes, Mitsubishi, Nissan, Toyota, Volkswagon, and Volvo.
PK-3 and the transponder-based systems use a transponder system that locks out the ignition and fuel system.
This transponder system is comprised of two parts. The first part, the transceiver, circles the key switch
and is activated when the key is placed in the key switch or turned to the run position. Upon activation, the
transceiver will excite the transponder, which is located (but not visible) in the head of the ignition key. The key
24
© 2004 Directed Electronics, Inc. Vista, CA
transponder will then send a unique code back to the transceiver for evaluation. If the code matches a
valid code of the system, the vehicle will be allowed to start. Most of these transponder-based systems can be
bypassed using p/n 555U. Some may require additional parts from the vehicle manufacturer. Consult you dealer
for the applications. For most Ford PATS transponders, as well as Lexus and Toyotas, p/n 555F can be used, except
for the following vehicles, which will require p/n 555U : ‘97 and newer Mark VII, and 2000 and newer
Taurus/Sable, Contour/Mystique and Focus.
bypassing GM vehicle anti-theft systems (VATS)
Vehicles with the GM VATS (Pass Key) systems have a resistor embedded in the ignition key. If the VATS decoder
module does not measure the proper resistance when the vehicle is started, the starter and fuel pump may be
disabled for up to ten minutes. An optional "VATS pack" of resistors is available (p/n 652T). One of the resistors in
the pack will match the resistor in the key.
The VATS wires will be two very light-gauge wires coming out of the steering column. The colors of the wires vary,
but they are often contained in orange tubing - either both will be white wires, or one wire will be purple/white
and the other white/black. Determine the value of the resistor in the key. Then follow the diagram below to
bypass VATS during remote start operation. If the 3/1 BLUE status output has been programmed for factory security re-arm, use the H3/2 BLUE/BLACK third ignition output to control the relay.
NOTE: When connecting to the VATS wires, it is not important which wire is cut.
WHITE OR WHITE/BLACK
TO IGNITION KEY SWITCH
WHITE OR PURPLE/WHITE
PROPER RESISTOR VALUE
H3/1 BLUE OR
H3/2 BLUE/BLACK
85
86
87 87A
X
CUT
30
X
(+) 12V CONSTANT FUSED
DIA-621
© 2004 Directed Electronics, Inc. Vista, CA
TO VATS DECODER MODULE
25
plug-in LED and valet/program switch
These plug into the module. The status LED plugs into the small two-pin socket, while the Valet®/Program switch
should be plugged into the larger blue two-pin connector. The status LED fits in a 9/32-inch hole.
Status LED
Valet®/Program Switch
DIA-41
programmer interface, 3-pin port
The black 3-pin port is provided for programming of the unit. The unit can also be programmed using the
Bitwriter. When using the Bitwriter, it is possible to configure any and all of the programmable functions as well
as lock the Transmitter/Receiver and System Features Learn Routines so that unauthorized users cannot change
the configuration or program transmitters to the unit.
When the learn routines have previously been programmed using the Bitwriter, they may have been locked.
Before proceeding with reprogramming the learn routines, they must be unlocked with the Bitwriter - this
cannot be done manually with the Valet switch.
26
© 2004 Directed Electronics, Inc. Vista, CA
programming jumpers
light flash (+)/(-)
This jumper is used to determine the light flash output polarity. In the (+) position, the on-board relay is enabled
and the unit will output (+)12V on the WHITE wire, H1/2. In the (-) position, the on-board relay is disabled. The
WHITE wire, H1/2, will supply a 200mA (-) output suitable for driving factory parking light relays.
NOTE: For parking light circuits that draw 10 amps or more, the internal jumper must be switched
to a (-) light flash output. P/N 8617 or a standard automotive SPDT relay must be used on the
H1/2 light flash output harness wire.
tach threshold on/off
In most cases, this jumper can be left in the OFF position. Some new vehicles use less than 12 volts in their
ignition systems. The unit may have trouble learning the tach signal in these vehicles. Changing the jumper to
the ON setting changes the trigger threshold of the digital tach circuit so it will work properly with these vehicles. The vehicles affected include many newer Dodge/Chrysler/Plymouth vehicles, such as the Neon, Cirrus,
Stratus, Breeze and LH-based vehicles.
© 2004 Directed Electronics, Inc. Vista, CA
27
transmitter/receiver learn routine
The system comes with transmitters that have been taught to the receiver. The receiver can store up to 4 different transmitter codes in memory. Use the following learn routine to add transmitters to the system or to change
button assignments if desired.
The learn routine may be locked if previously programmed using the Bitwriter. If the horn generates one long
honk when attempting to program the unit, the learn routine is locked and must be unlocked using the Bitwriter™
before proceeding.
The Valet/Program switch, plugged into the blue port, is used for programming. There is a basic sequence of steps
to remember whenever programming this unit: Key, Choose, Transmit and Release.
1.
Key. Turn the ignition to the ON position.
2.
Choose. Within 10 seconds, press and release the Program switch the number of times corresponding to the desired channel listed below. Once you have selected the channel, press
the switch once more and HOLD it. The LED will flash and the horn will honk (if connected)
to confirm the selected channel. Do not release the Program switch.
CHANNEL NUMBER
FUNCTION
1
Auto Learn
2
Arm Panic On/Panic Off
3
Disarm Panic Off
4
Silent Mode Channel 2
5
Remote Start
6
Channel 4
7
Short Run/Turbo
8
Timer Mode
9
Arm/Disarm/Panic
10
Panic Only
11
Delete All Transmitters
WIRE COLOR
RED/WHITE
VIOLET/BLACK
*NOTE: For Auto Learn Configurations, see Transmitter Configurations section of this guide.
**NOTE: If any button from a known transmitter is programmed to Channel 11, all transmitters will be erased from memory and will revert to the default feature settings. This is
useful in cases where the customer's transmitters are lost or stolen.
28
© 2004 Directed Electronics, Inc. Vista, CA
3.
Transmit. While HOLDING the Valet/Program switch, press the button on the transmitter
that you would like to control the selected receiver channel. The unit will chirp to confirm
that the code has been successfully programmed. It is not possible to teach a transmitter
button to the system more than once.
4.
Release. Once the code is learned, the Valet/Program switch can be released.
You can advance from programming one channel to another by releasing the Valet/Program switch and tapping
it to advance channels and then HOLDING it. For instance: You have programmed Channel 1 and you want to
program Channel 2. Release the Valet/Program switch. Press it one time and release it to advance from Channel
1 to Channel 2. Now, press and HOLD the Valet/Program switch. The LED will flash two times and the horn will
honk twice (if connected). As before, do not release it.
If you want to program Channel 3 after programming Channel 1, release the Valet/Program switch, press it twice
and release it to advance to Channel 3. Then press it once more and HOLD it. The horn will honk three times (if
connected) and the LED will flash three times to confirm it is ready to receive the code from the transmitter.
Learn Routine will be exited if:
■ Ignition is turned off.
■ Program switch is pressed too many times.
■ More than 15 seconds elapses between programming steps.
One long horn honk indicates that Learn Routine has been exited.
© 2004 Directed Electronics, Inc. Vista, CA
29
transmitter configurations
The transmitters can be programmed with the separate or single button arm/disarm configurations by using the
Auto-learn functions in the Transmitter/Receiver Learn Routine.
button configuration
controls the Lock/Panic ON/Panic OFF function.
controls the Disarm/Panic OFF function.
controls Silent Mode™and an Auxiliary Output.
controls Remote Start.
+
+
+
controls Timer mode.
controls Turbo/Short Run.
controls Channel 4 output.
operating settings learn routine
The System Features Learn Routine™ dictates how the unit operates. Due to the number of features, the
features have been divided into two menus. It is possible to access and change any of the feature settings using the Valet®/Program switch. However, this process can be greatly simplified by using the Bitwriter™.
Any of the settings can be changed and then assigned to one of up to four transmitters, a feature called Owner
Recognition. Each time that particular transmitter is used to disarm the system, the assigned feature settings will
be recalled. Owner Recognition is only possible when programming the unit via the Bitwriter.
The learn routine may be locked if previously programmed using the Bitwriter. If the horn generates one
long honk when attempting to program the unit, the learn routine is locked and must be unlocked using
the Bitwriter™ before proceeding.
30
© 2004 Directed Electronics, Inc. Vista, CA
To program the features using the Valet switch:
1.
Key. Turn the ignition on and then back off.
2.
Select Menu. Press and HOLD the Valet®/Program switch. When the LED flashes once and
the horn honks Menu One has been selected. Continue to hold the switch until the LED
flashes twice and the horn honks twice Menu Two has now been selected. Release the
switch after the Menu choice has been selected.
3.
Choose. Within 10 seconds, press and release the Valet®/Program switch the number of
times corresponding to the feature number you want to program and then press and hold
the switch. (See Feature Menus.)
After a second, the LED will flash to indicate which feature you have accessed. For example, in Menu Two, groups
of eight flashes would indicate access to the activation pulse setting (Feature 2-8). The horn will also honk eight
times (if connected).
4.
Transmit. The transmitter is used to select the desired setting. Pressing
will change
the feature to the LED ON setting (or will flash once for features with more than 2 settings). The horn will honk once (if connected). Pressing
will change the setting to
the LED OFF setting (or will flash two or more times for features with more than 2 settings).
5.
Release. The Valet®/Program switch can now be released.
You can advance from feature to feature by pressing and releasing the Valet®/Program switch the number of times
necessary to get from the feature you just programmed to the feature you wish to access. For example, in Menu
One, if you just programmed Feature 1-2 and you next want to program Feature 1-3 to off, release the
Valet/Program switch. Press and release it once to advance from Feature 1-2 to Feature 1-3. Then press it once
more and HOLD it. The LED will flash in groups of 3 and the horn will honk 3 times (if connected) to confirm that
you have accessed Feature 1-3.
The learn routine will be exited if:
■ The ignition is turned on.
■ The Valet/Program switch is pressed too many times.
■ More than 15 seconds elapses between programming steps.
One long horn honk (if connected) indicates that the Learn Routine has been exited.
© 2004 Directed Electronics, Inc. Vista, CA
31
feature menus
Factory default settings are indicated in bold in the following feature tables.
menu #1
FEATURE
NUMBER
DEFAULT - LED ON SETTING
(PRESS CHANNEL 1)
LED OFF SETTING
(PRESS CHANNEL 2)
1-1
Active arming
Passive arming
1-2
Chirps ON
Chirps OFF
1-3
Ignition lock ON
Ignition lock OFF
1-4
Ignition unlock ON
Ignition unlock OFF
1-5
Active locking
Passive locking
1-6
Panic with ignition ON
Panic with ignition OFF
1-7
Door lock pulse duration 0.8 seconds
Door lock pulse duration 3.5 seconds.
1-8
Double Unlock Pulse OFF
Double Unlock Pulse ON
1-9
Channel 2 delayed validity
Channel 2 latched (2), latch reset with ignition
(3), 30 second timed (4)
1-10
FAD with Channel 2 ON
FAD with Channel 2 OFF
1-11
Security features ON
Security features OFF (starter kill)
1-12
Code Hopping ON
Code Hopping OFF
1-13
Channel 4 Validity
Latched, Latch reset with ignition, 30-sec.
timed
NOTE: The numbers in parentheses indicate the number of times the LED will flash.
*N
32
© 2004 Directed Electronics, Inc. Vista, CA
menu #2
FEATURE
NUMBER
DEFAULT - LED ON SETTING
(PRESS CHANNEL 1)
LED OFF SETTING
(PRESS CHANNEL 2)
2-1
Engine check ON
Engine check OFF
2-2
Tachometer engine check
Voltage engine check
2-3
12 minutes run time
24 minutes, 60 minutes run time
2-4
Flashing parking light output
Constant parking light output
2-5
Cranking time 0.6 sec. (1)*
Cranking time 0.8 (2), 1.0 (3), 1.2 (4), 1.4 (5),
1.6 (6), 1.8 (7), 2.0 (8), 4.0 (9) sec.*
2-6
Voltage check high level
Voltage check low level
2-7
Short run (turbo) 1 minute
3, 5, 10 minutes
2-8
Activation pulse: 1 (1)
Activation pulses: 2 (2), 3 (3)
2-9
2nd Ignition output
2nd Accessory output
2-10
Accessory state during wait to start OFF
Accessory state during wait to start ON
2-11
2nd status output NORMAL
Rear defogger latch, rear defogger pulse
2-12
Anti-Grind ON
Anti-Grind OFF
NOTE: The numbers in parentheses indicate the number of times the LED will flash.
*N
© 2004 Directed Electronics, Inc. Vista, CA
33
feature descriptions
The features of the system are described below. Features that have additional settings that can be selected only
when programming with the Bitwriter are indicated by the following icon:
menu #1
1-1 ACTIVE/PASSIVE ARMING: When active arming is selected, the starter kill will arm (if connected) only when
the transmitter is used. When set to passive arming, the starter kill will arm (if connected) 30 seconds after the
ignition key is turned off.
1-2 CHIRPS ON/OFF: This feature controls the chirps that confirm arming and disarming of the system. A siren or
horn must be connected to the H1/10 BROWN wire.
1-3 IGNITION LOCK ON/OFF: When turned on, the doors will lock three seconds after the ignition is turned on and
unlock when the ignition is turned off.
1-4 IGNITION UNLOCK ON/OFF: When ON this feature will unlock the doors when the ignition is turned off.
1-5 ACTIVE/PASSIVE LOCKING: If passive arming is selected in Menu One, Feature 1-1, then the system can be
programmed to either lock the doors when passive arming occurs, or only lock the doors when the system is armed
with a transmitter. Active locking means the doors will not lock when the system passively arms. Passive locking
means that the doors will lock whenever the system passively arms the optional starter kill (if connected).
1-6 PANIC WITH IGNITION ON/OFF: This feature allows the user to panic the system sounding the siren while the
ignition is on.
1-7 DOOR LOCK PULSE DURATION: Some European vehicles, such as Mercedes-Benz and Audi, require longer lock
and unlock pulses to operate the vacuum pump. Programming the system to provide 3.5 second pulses will accommodate the door lock interface in these vehicles. The default setting is 0.8 second door lock pulses.
1-8 DOUBLE PULSE UNLOCK OFF/ON: Some vehicles require two pulses on a single wire to unlock the doors. When
the double pulse unlock feature is turned on, the BLUE H4/3 wire will supply two negative pulses instead of a
single pulse. At the same time, the GREEN H4/1 wire will supply two positive pulses instead of a single pulse.
This makes it possible to directly interface with double pulse vehicles without any extra parts.
34
© 2004 Directed Electronics, Inc. Vista, CA
1-9 CHANNEL 2:
■ In the delayed validity default setting the Channel 2 output will output a negative (-) signal after the
button is pressed for more than 1.5 seconds and will continue until the button is released.
■ The latched output selection will output a negative signal as soon as the
button is pressed and will
continue until the button is pressed again.
■ The latched/reset with ignition output selection operates just like the latched output but will reset or stop
when the ignition is turned on.
■ The 30-second timed output selection will latch the Channel 2 output on for 30 seconds when the remote
button is pressed or until the button is pressed again within the 30 seconds.
1-10 FACTORY ALARM DISARM (FAD) WITH CHANNEL TWO ON/OFF: Any time Channel 2 is activated from the
remote transmitter the factory disarm output will pulse to disarm the vehicle’s factory anti-theft device. This
option can be programmed off if desired.
1-11 SECURITY FEATURES ON/OFF: When On the security features (starter kill and panic) will activate if the ignition key is turned On while the doors are locked. When Off the security features (starter kill and panic) will not
activate if the ignition key is turned On while the doors are locked.
1-12 CODE-HOPPING ON/OFF: The system features Code-Hopping as an option. To use Code-Hopping technology,
this feature must be programmed On.
1-13 CHANNEL 4: This output can be programmed to produce a validity output that will stay active as long as
the transmitter button assigned to that channel is pressed, a latched output, a latched output reset with ignition, or a 30-second timed output.
© 2004 Directed Electronics, Inc. Vista, CA
35
menu #2
2-1 ENGINE CHECK ON/OFF: In the default setting the remote start will monitor either the vehicle's tach wire or
voltage depending on the programming of Feature 2-2. If programmed off, the vehicle will crank for the programmed crank time (Feature 2-5) and will not verify with tach or voltage that the vehicle is running. In the off
setting, if the vehicle fails to start, the ignition can stay on for the entire run duration. Using tach or voltage
check is always recommended if possible.
2-2 TACH WIRE SENSE/VOLTAGE SENSE: If the tachometer signal wire is used, this feature must be left in the
default (tach wire connected) setting. If programmed to the voltage sense setting, the unit will crank the starter
for a preset time that can be programmed in Feature 2-5. Once the starter has been engaged, the system will
check the voltage level to verify the engine is running. The threshold for the voltage level test can be programmed in Feature 2-6. When using voltage sense mode, connection of the H3/5 WHITE tachometer input is not
necessary.
2-3 RUN TIME 12/24/60 MINUTES: This feature controls how long the engine will run before it “times out”
and shuts down. Programmed to the default setting the engine will run for 12 minutes. If the 24-minute
run time is desired, change this feature to the on-board LED off setting.
2-4 FLASHING PARKING LIGHT OUTPUT: In the default setting, the unit will flash the vehicle’s parking lights while
remote started. The constant setting will turn the parking lights on solidly for the entire run duration.
2-5 CRANKING TIME 0.6/0.8/1.0/1.2/1.4/1.6/1.8/2.0/4.0: If feature 2-2 is programmed to the voltage sense
setting, the crank time must be set to the appropriate duration. The default setting is 0.6 seconds. If a different crank time is desired, select feature 2.5 and (while pressing the Valet®/Program switch) advance to the next
time by pressing the channel 2 button. The unit will flash the LED to indicate which time is selected. Once the
4.0 second setting is reached the next press of channel 2 will reset the system to the shortest setting.
2-6 VOLTAGE CHECK LEVEL HIGH/LOW: This feature only functions when Feature 2-2 is programmed to voltage
sense. Some vehicles have many accessories, which are turned on when remote started. In these vehicles, the
variation of voltage between the engine off and the vehicle running is very slight and the remote start unit may
“think” the vehicle has not started. This can cause the remote start to shut down after the vehicle has been
started. If this is the case, program this feature to the LOW position.
2-7 SHORT RUN (TURBO TIMER): When the
and
buttons on the transmitter are pressed simultane-
ously, the vehicle will continue to run for the programmed short-run time. The factory default is 1 minute.
2-8 ACTIVATION PULSE COUNT: This feature allows the number of pulses to activate the remote start feature to
be changed from 1, 2, or 3 pulses. The pulse count programmed to start the vehicle will also be the same required
to shut down the remote start.
36
© 2004 Directed Electronics, Inc. Vista, CA
2-9 2 nd IGNITION/ACCESSORY OUTPUT: This will allow the PINK/WHITE to be used as a 2nd ignition or an accessory.
2-10 ACCESSORY STATE DURING WAIT-TO-START: This will allow the programming of the accessory wire during the
wait-to-start period of a diesel motor. When ON the accessory comes on when the wait-to-start output is activated and stays on, dropping out during crank and returning once the car has started. When OFF the accessory
will activate as a normal accessory.
2-11 2nd STATUS OUTPUT: This status will activate 10 seconds after the car has started. It is intended to operate
the defogger circuit. The output can be programmed to a latched or a pulsed output. When programmed to the
latched output the status will only stay active for 10 minutes.
2-12 ANTI-GRIND ON/OFF: With the anti-grind On (default) the ground-when-armed output will be active during
remote start operation. If accessories such as a voice module or window module are added to the unit, it may be
necessary to program this feature off.
tach learning
To learn the tach signal:
1.
Start the vehicle with the key.
2.
Within 5 seconds, press and HOLD the Valet/Program switch.
3.
The LED will light constant when the tach signal is learned.
4.
Release the Program switch.
DRW-96
© 2004 Directed Electronics, Inc. Vista, CA
37
shutdown diagnostics
The unit has the ability to report the cause of the last shutdown of the remote start system.
To enter diagnostic mode:
1.
Turn the ignition off.
2.
Press and HOLD the Valet/Program switch.
3.
Turn the ignition on and then off.
4.
Release the Valet/Program switch.
5.
Press and release the Valet/Program switch.
The LED will now report the last system shutdown by flashing for one minute in the following grouped patterns:
LED FLASHES
SHUTDOWN MODE
One
System timed out
Two
Over-rev shutdown
Three
Low or no RPM
Four
Transmitter Shutdown (or optional push-button)
Six
(+/-) Shutdown
Seven
(-) Neutral safety shutdown
Eight
Wait-to-start timed out
The LED will stop flashing when the ignition is turned on.
38
© 2004 Directed Electronics, Inc. Vista, CA
rapid resume logic
The Rapid Resume Logic feature ensures that when the security system is powered back up after power has been
disconnected, the system will resume the same state it was in before power was lost. For example, if power is
disconnected during a full trigger sequence, the system will still be in the full trigger sequence when power is
reconnected to the unit. If power is disconnected while the unit is disarmed, it will still be disarmed when power
is restored.
timer mode
By pressing the remote
and
buttons the parking lights will flash 4 times and then start the vehicle and run for the set dura-
tion. The remote start can be shut off by the transmitter by pressing the remote start button
and remain in timer mode, but if any
other shut down zones or the ignition becomes active the timer mode will cancel.
1.
Press Timer mode buttons.
2.
The vehicle will confirm with 4 parking light flashes.
3.
A 1-second delay will start.
4.
The system will start the car and will run for the specified duration, unless shut down by the remote start button
with the remote start button
5.
. If shut down
the system will remain in timer mode.
The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down wires.
To exit timer mode, turn the ignition switch on any time the engine is running. The parking lights will flash 4 times, indicating timer mode
has been exited.
5.
The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down wires.
© 2004 Directed Electronics, Inc. Vista, CA
39
valet mode
To enter or exit Valet® Mode with the Valet®/Program switch:
1.
Turn the ignition on and then off.
2.
Within 10 seconds, press and release the Valet®/Program switch.
The status LED will light solid if you have entered Valet® Mode, and will go out if you have exited Valet® Mode.
safety check
Before vehicle reassembly, the remote system must be checked to ensure safe and trouble-free operation. The following test procedure must be used to verify proper installation and operation of the system. The installation
must be completed before testing, including connection to the brake switch and hood switch.
1. Test the BRAKE shutdown circuit: With the vehicle in Park (P), activate the remote start system. Once the
engine is running, press the brake pedal. The engine should shut down immediately. If the engine continues
to run, check the brake circuit connection.
2. Test the HOOD PIN shutdown circuit: With the vehicle in Park (P), open the hood. Activate the remote start
system. The vehicle should not start. If the starter engages, check your hood pin and connections.
NOTE: If programmed for Diesel Mode, the system will turn on the ignition, but the starter should
not engage with the hood open.
3. Test the NEUTRAL SAFETY shutdown circuit:
IMPORTANT! Make sure there is adequate clearance to the front and rear of the vehicle before
attempting this test.
a. Make sure the hood is closed and no other shutdown circuits are active.
b. Set the emergency brake.
c. Turn the ignition key to the run position but do not start the engine.
d. Put the vehicle in Drive (D).
e. Put your foot over the brake pedal but do not press down on it. Be ready to step on the brake to shutdown the remote start system.
40
© 2004 Directed Electronics, Inc. Vista, CA
f.
Activate the remote start system.
■ If the starter engages, immediately step on the brake to shut down the system. If it does engage,
recheck the neutral safety input connection. The vehicle may use a mechanical neutral safety switch.
(See H3/5 BLACK/WHITE neutral safety switch input in Remote Start Harness Wire Connection Guide
section of this guide.)
■ If the starter does not engage, the test is complete.
Once the system passes the three tests, the vehicle can be re-assembled and delivered. Do not the use the remote
start system or finalize the installation if it fails any of the safety check tests.
troubleshooting
■ The ignition comes on, but the starter will not crank.
Does it start with the key in the ignition? If so, does the vehicle have a VATS Pass-Key system?
Will it start with the brake pedal depressed? (Make sure to disconnect the brake shutdown when performing this
test.) If so, it may have a brake/starter interlock.
Is the correct starter wire being energized? Check by energizing it yourself with a fused test lead.
■ The starter cranks for six seconds but does not start.
Either the wrong ignition wire is being energized, the unit's ignition and accessory wires have been connected
backwards, or the vehicle has two ignition circuits. Try activating the unit with the ignition key in the “run” position. If the vehicle then runs normally, retest your ignition system.
■ The starter continues to crank even though the engine has started.
Has the tach wire been learned? See Tach Learning section of this guide.
Is the tach wire receiving the correct information? Either the wrong tach wire has been used, or a bad connection exists.
■ The climate control system does not work while the unit is operating the vehicle.
Either the wrong accessory wire is being energized or more than one ignition or accessory wire must be energized in order to operate the climate control system.
■ The remote start will not activate.
1. Check harnesses and connections. Make sure the harnesses are fully plugged into the remote start module.
Make sure there are good connections to the vehicle wiring.
2. Check voltage and fuses. Use a meter and check for voltage between the red wire in the 5 pin ribbon harness
and the black ground wire. If you have less than battery voltage, check both 30A fuses on the relay satel© 2004 Directed Electronics, Inc. Vista, CA
41
lite. Also make sure that the ground wire is going to a chassis ground and not to something under the dash.
3. Check diagnostics. The diagnostics will tell you which shutdown is active or not connected.
■ The remote start will activate but the starter never engages.
1. Check for voltage on the purple starter wire two seconds after the remote start becomes active. If there is
voltage present, skip to Step 4. If there is not voltage present, advance to Step 2.
2. Check the 30A fuses.
3. Check diagnostics. If the gray/black wire is detecting ground upon activation, the starter will not crank.
4. Make sure the purple starter wire is connected on the starter side of the optional starter kill relay.
5. Does the vehicle have an immobilizer? Some immobilizer systems will not allow the vehicle to crank if active.
6. Check connections. The two red heavy gauge input wires on the relay satellite should have solid connections.
"T-taps", or "scotch locks" are not recommended for any high current heavy gauge wiring. Also, if the vehicle
has more than one 12-volt input wire, then connect one red wire to each.
■ The vehicle starts, but immediately dies.
1. Does the vehicle have an immobilizer? The vehicles immobilizer will cut the fuel and/or spark during unauthorized starting attempts.
2. Is the remote start programmed for voltage sense? If so, the start time may not be set high enough, or you
may have to adjust the voltage threshold in programming. Voltage sense will not work on some vehicles.
3. Check diagnostics. Sometimes a shutdown will become active during cranking or just after cranking.
■ The vehicle starts, but the starter keeps running.
1. Is the system programmed for engine checking off or voltage sense? When programmed for either of these
features, the engine cranks for the preprogrammed crank time regardless of how long it takes to start the
vehicle to actually start. Adjust to a lower cranking time.
2. Was the Tach Learn successful? The LED must light solidly and brightly to indicate a successful learn.
3. Make sure that there is a tach signal right at the purple/white tach input wire of the remote start. If not,
recheck the connection to the vehicle’s tach wire and make sure the wire is not broken or shorted to ground
leading to the remote start.
■ The vehicle will start and run only for about 10 seconds.
1. Is the remote start programmed for voltage sense? Try programming the unit for low voltage reference. If
this does not work, a tach wire should be used.
2. Check diagnostics.
42
© 2004 Directed Electronics, Inc. Vista, CA
wiring quick reference guide
© 2004 Directed Electronics, Inc. Vista, CA
43
44
PURPLE starter side starter wire
GREEN key side starter wire
RED 12V constant input
ORANGE accessory output
BLUE (-) status output
ORANGE (-) 200mA 2nd accessory output
VIOLET (-) 200mA starter output
PINK (-) 200mA 3rd ignition output
These signals are from the
Relay Satellite ribbon harness
and are provided to drive
additional optional relays.
Relay Satellite
ribbon harness
PINK/WHITE 2nd ignition output
RED/WHITE 12V constant input
PINK ignition output
RED 12V constant input
Heavy guage wires
relay satellite wiring quick reference guide
© 2004 Directed Electronics, Inc. Vista, CA
Download PDF