Sharp | R-933S | Product data | Sharp R-933S Product data

Instructions for the use - Installation advices
GAS COOKERS
Models:
EGC 833 ..
EGC 933 ..
100
% ELBA QUALITY
MADE IN ITALY
HOME APPLIANCES
Made in Italy
Dear Customer,
Thank you for having purchased and given your preference to
our product.
The safety precautions and recommendations reported below
are for your own safety and that of others. They will also provide
a means by which to make full use of the features offered by your
appliance.
Please preserve this booklet carefully. It may be useful in future, either to yourself or to others in the event that doubts should
arise relating to its operation.
This appliance must be used only for the task it has explicitly been designed for, that is for cooking foodstuffs. Any
other form of usage is to be considered as inappropriate and
therefore dangerous.
The manufacturer declines all responsibility in the event
of damage caused by improper, incorrect or illogical use of
the appliance.
2
Read the instructions carefully before installing and using the appliance.
CAUTION: this apparatus must only be installed in a permanently
ventilated room in compliance with the applicable regulations.
Important:
This appliance is designed and manufactured solely for the cooking of domestic (household) food and is not suitable for any non
domestic application and therefore should not be used in a commercial environment.
This appliance guarantee will be void if the appliance is used within
a non domestic environment i.e. a semi commercial, commercial
or communal environment.
FIRST USE OF THE OVEN
It is advised to follow these instructions:
• Furnish the interior of the oven as described at chapter “Cleaning and maintenance”.
• Switch on the empty oven on max to eliminate grease from the
heating elements.
• Let the oven cool down and clean the interior of the oven with a
cloth soaked in water and neutral detergent, then dry carefully.
3
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS
After having unpacked the appliance, check to ensure that it is not
damaged and that the oven door closes correctly. In case of doubt,
do not use it and consult your supplier or a professionally qualified
technician.
Packing elements (i.e. plastic bags, polystyrene foam, nails, packing
straps, etc.) should not be left around within easy reach of children,
as these may cause serious injuries.
4
• Do not attempt to modify the technical characteristics of the appliance as this may cause danger to users.
• If you should decide not to use this appliance any longer (or
decide to substitute another model), before disposing of it, it
is recommended that it be made inoperative in an appropriate
manner in accordance to health and environmental protection
regulations, ensuring in particular that all potentially hazardous
parts be made harmless, especially in relation to children who
could play with unused appliances.
• After use, ensure that the knobs are in the off position.
• Household appliances are not intended to be played with by
children.
• Keep children away from the cooker during use.
• Children, or persons with a disability which limits their ability to use
the appliance, should have a responsible person to instruct them
in its use. The instructor should be satisfied that they can use the
appliance without danger to themselves or their surroundings.
• During and after use of the appliance, certain parts will become
very hot. Do not touch hot parts. Care should be taken to avoid
touching heating elements inside the oven.
• Some appliances are supplied with a protective film on steel and
aluminium parts.
This film must be removed before using the appliance.
• WARNING: When correctly installed, your product meets all
safety requirements laid down for this type of product category.
However special care should be taken around the rear or the
underneath of the appliance as these areas are not designed or
intended to be touched and may contain sharp or rough edges,
that may cause injury.
• Fire risk! Do not store flammable material in the oven or in the
storage compartment (some models only).
• Make sure that electrical cables connecting other appliances in
the proximity of the cooker cannot come into contact with the hob
or become entrapped in the oven door.
• Do not line the oven walls with aluminium foil. Do not place baking trays or the drip tray on the base of the oven chamber.
• The manufacturer declines all liability for injury to persons or damage to property caused by incorrect or improper use of the appliance.
• The various components of the appliance are recyclable. Dispose of them in accordance with the regulations in force in your
country.
• Always use oven gloves when removing the shelf and food tray
from the oven whilst hot.
• Do not hang towels, dishcloths or other items on the cooker or its
handle – as this could be a fire hazard.
• Clean the oven regularly and do not allow fat or oils to build up in
the oven base or trays. Remove spillages as soon as they occur.
• Do not stand on the cooker or on the open oven door.
• Always stand back from the cooker when opening the oven door
to allow steam and hot air to escape before removing the food.
• Safe food handling: Leave food in the oven for as short a time
as possible before and after cooking. This is to avoid contamination by organisms which may cause food poisoning. Take particular care during warmer weather.
• This appliance is for domestic use only.
5
1
COOKING HOB
Fig. 1.1
1
3
2
GAS BURNERS
1. Semi-rapid burner (SR) 1,75 kW
2. Rapid burner (R) 3,00 kW
3. Triple-ring burner (TR) 3,50 kW
2
CONTROL PANEL
Fig. 2.1
1
2
3
4
CONTROLS DESCRIPTION
1. Gas oven control knob
2. Rear left burner control knob
3. Front left burner control knob
4. Central right burner control knob
6
5. Gas burners electronic igniter pushbutton (cooktop burners only)
5
3
USE OF THE HOB BURNERS
Each burner is controlled by a gas tap (fig.
3.1) assuring the opening and the closing
of the gas supply.
Make the knob symbols match with the indicator on the control panel to obtain:
•
symbol : off
•
symbol : full on (nominal rate)
•
symbol : reduced rate
√√
The maximum aperture position permits rapid boiling of liquids, whereas
the minimum aperture position allows
slower warming of food or maintaining
boiling conditions of liquids.
√√
√√
Fig. 3.1
To reduce the gas flow to minimum,
rotate the knob further anti-clockwise
to point the indicator towards the small
flame symbol.
Other
intermediate
operating
adjustments can be achieved by positioning the indicator between the maximum and minimum aperture positions,
and never between the maximum
aperture and closed positions.
Fig. 3.2
In the event of the burner flames being
accidentally extinguished, turn off the
burner control and do not attempt to
re-ignite the burner for at least 1 min.
N.B. When the cooker is not being
used, set the gas knobs to their closed
positions and also close the cock valve on the gas bottle or the main gas
supply line.
Caution!
The cooking hob becomes very hot
during operation.
Keep children well out of reach.
7
LIGHTING THE BURNERS
To ignite the burner, the following instructions are to be followed:
1. Press in the corresponding knob and
turn counter-clockwise (fig. 3.2 ) to the
full flame position marked by the
(full on) symbol (fig. 3.1).
2. Press the ignition button marked by
the symbol
(fig. 3.3).
The sparks produced by the electrodes situated next to the burner will
light the selected burner.
In the case of a mains failure light the
burner with a match or lighted taper.
3. Adjust the gas valve to the desired position.
To turn it off, turn the knob towards the
right, up to the safety click.
On the control panel, near every knob, there is a diagram that indicates which burner
is controlled by that knob.
The suitable burner must be chosen according to the diameter and the capacity used.
As an indication, the burners and the pots
must be used in the following way:
DIAMETERS OF PANS WHICH MAY
BE USED ON THE BURNERS
BURNERS
MINIMUM
MAXIMUM
Semi-rapid
16 cm
24 cm
Rapid
24 cm
26 cm
Triple-ring
26 cm
28 cm
Wok pan
Max 36 cm
do not use pans with concave or convex bases
If your local gas supply makes it difficult to
light the burner with the knob set to maximum, set the knob to minimum and repeat
the operation.
It is important that the diameter of the pot
be suitable to the potentiality of the burner
so as not to compromise the high output
of the burners and therefore energy waste.
BATTERY IGNITION
A small pot on a large burner does not give
you a boiling point in a shorten amount of
time since the capacity of heat absorption
of a liquid mass depends on the volume
and the surface of the pot.
If the electronic ignition does not work
make sure that the battery, installed on the
back of the cooker, is not flat and has been
installed correctly (see the chapter “Battery
installation”, page 29).
Fig. 3.3
8
CHOICE OF THE BURNER
Fig. 3.4
CORRECT USE OF THE TRIPLE-RING BURNER
The flat-bottomed pans are to be placed directly onto the pan-support.
When using a WOK you need to place the supplied stand in the burner to avoid any faulty
operation of the triple-ring burner (Figs. 3.5a - 3.5b).
IMPORTANT:
The special grille for wok pans (fig. 3.5b) MUST BE PLACED ONLY over the pan-rest for
the triple-ring burner.
WRONG
CORRECT
Fig. 3.5a
Fig. 3.5b
9
4
USE OF THE GAS OVEN
The glass on the oven door reaches
high temperatures during operation.
Keep children away.
The cooker lid must be kept open when
the gas oven is in use.
WARNING:
The door is hot, use the handle.
OVEN DOOR GUARD
The glass on the oven door reaches high
temperatures during operation.
For child safety, a door guard can be fitted
to prevent contact with the hot glass.
The door guard (thermoreflective door inner glass) is supplied as an accessory at
extra cost, if required.
Contact the After-Sales Service and indicate the model name of your product (see
product data plate).
GENERAL FEATURES
The oven is furnished completely clean; it
is advisable however, upon first use, to turn
the oven on to the maximum temperature
(position 10) to eliminate possible traces of
grease from the oven burner.
THERMOSTAT
The numbers 1 to 10 printed on the knob
(fig. 4.1) indicate the increasing oven temperature value (see table 4.2).
To regulate the temperature, make the
chosen number of the knob (fig. 4.1) match
with the indicator on the control panel.
The temperature is kept constant on the
regulated value.
The thermostat which regulates the flow of
gas to the oven burner has a safety valve
which automatically shuts off the gas supply when the flame goes out.
OVEN BURNER
It carries out normal “oven cooking”.
The gas flow to the burner is regulated by
a thermostat which allow to maintain the
oven temperature constant.
The control of the temperature is assured
by a thermostatic probe positioned inside
the oven.
The probe must be always kept in its housing, in a clean condition, as an incorrect
position or encrustment may cause an alteration in the control of the temperature.
The gas oven is provided with:
•
One gas burner (wattage: 3,20 kW),
located at the bottom, providing safety
valve device.
1
2
3
0
1
4
6
7
8
9
10
5
Fig. 4.1
Table. 4.2
IGNITION OF THE OVEN BURNER
ATTENTION: Never turn the control
knob before opening the oven door.
To ignite the oven burner:
1. Open the oven door to the full extent.
WARNING: Risk of explosion! The
oven door must be open during this
operation.
2. Approach a flame to the hole ‘A’ of the
oven floor (fig. 4.3) before turning the
gas thermostat.
3. Press in the oven control knob and
turn counter-clockwise (fig. 4.4) to position 10. Never turn the gas thermostat before approaching a flame to
the hole “A” of the floor.
Never continue this operation for
more than 15 seconds. If the burner
has still not ignited, wait for about
1 minute prior to repeating the ignition.
4. Check that the burner has lit; if not,
turn the knob clockwise back to “
”
(OFF) and repeat the procedure from
step 2.
5. Gently close the oven door and set the
oven control knob to the required temperature.
If the flame extinguishes for any reason,
the safety valve will automatically shut off
the gas supply to the burner.
To re-light the burner, first turn the oven
control knob to position “
” (OFF), wait
for at least 1 minute and then repeat the
lighting procedure.
COOKING EXAMPLES
Temperatures are approximate as they
vary depending on the quality and amount
of food.
Remember to use ovenproof dishes and
to adjust the oven temperature during cooking if necessary.
DISHES
TEMPERATURE
Lasagne
Baked pasta
Pizza
Creole rice
Baked onions
Spinach crêpes
Potatoes baked in milk
Stuffed tomateos
Cheese soufflé
Roast veal
Grilled veal chops
Chicken breasts with tomato
Grilled chicken - roast chicken
Veal loaf
Roast beef
Fillet of sole
Aromatic hake
Beignets
Ring cake
Plum tart
Jam tartlets
Sponge cake
Sweet dough
Sweet puffs
Plain sponge cake
190°C
190°C
220°C
190°C
190°C
185°C
185°C
180°C
170°C
180°C
210°C
180°C
190°C
175°C
170°C
175°C
170°C
160°C
150°C
170°C
160°C
170°C
160°C
170°C
170°C
A
Fig. 4.3
Fig. 4.4
11
5
CLEANING AND MAINTENANCE
GENERAL ADVICE
ENAMELLED PARTS
•
When the appliance is not being used,
it is advisable to keep the gas tap closed.
•
The periodical lubrication of the gas
taps must be done only by specialized
personnel.
•
If a tap becomes stiff, do not force;
contact your local After Sales Service
Centre.
All the enamelled parts must be cleaned
with a sponge and soapy water or other
non-abrasive products.
Dry preferably with a microfibre or soft
cloth.
Acidic substances like lemon juice, tomato
sauce, vinegar etc. can damage the enamel if left too long.
•
It is advisable to clean when the appliance is cold and especially when
cleaning the enamelled parts.
•
Avoid leaving alkaline or acidic substances (lemon juice, vinegar, etc.) on
the surfaces.
•
Avoid using cleaning products with a
chlorine or acidic base.
•
Important: The use of suitable protective clothing/gloves is recommended
when handling or cleaning of this appliance.
WARNING
When correctly installed, your product
meets all safety requirements laid down
for this type of product category.
However special care should be taken
around the rear or the underneath of the
appliance as these areas are not designed or intended to be touched and may
contain sharp or rough edges, that may
cause injury.
STAINLESS STEEL, ALUMINIUM
PARTS, PAINTED AND SILK-SCREEN PRINTED SURFACES
Clean using an appropriate product.
Always dry thoroughly.
IMPORTANT: these parts must be cleaned
very carefully to avoid scratching and abrasion. You are advised to use a soft cloth
and neutral soap.
CAUTION: Do not use abrasive substances or non-neutral detergents as these
will irreparably damage the surface.
Attention! The appliance gets very hot, mainly around the cooking areas. It is very
important that children are not left alone in the kitchen when you are cooking.
Do not use a steam cleaner because the moisture can get into the appliance thus
make it unsafe.
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door
glass or the glass lid (models with glass lid only) since they can scratch the surface, which may result in shattering of the glass.
12
GAS TAPS
BURNERS
Periodic lubrication of the gas taps must be
carried out by specialist personnel only.
In the event of operating faults in the gas
taps, call the Service Department.
They can be removed and washed with
soapy water only.
They will remain always perfect if cleaned
with products used for silverware.
After cleaning or wash, check that burnercaps and burner-heads are dry before placing them in the respective housings.
INSIDE OF OVEN
The oven should always be cleaned after
use when it has cooled down.
The cavity should be cleaned using a mild
detergent solution and warm water.
Suitable proprietary chemical cleaners
may be used after first consulting with the
manufacturers recommendations and testing a small sample of the oven cavity.
Abrasive cleaning agents or scouring pads/
cloths should not be used on the cavity surface.
Check that the electrode S (figs. 5.2, 5.4)
next to each burner is always clean to ensure trouble-free sparking.
Note: The electrode “S” must be very
carefully cleaned.
To avoid damage to the electric ignition
do not use it when the burners are not
in place.
NOTE: The manufacturers of this appliance will accept no responsibility for damage
caused by chemical or abrasive cleaning.
Let the oven cool down and pay special
attention no to touch the hot surfaces
inside the oven cavity.
Fire risk! Do not store flammable material
in the oven.
OVEN DOOR
CORRECT REPLACEMENT OF THE
SEMI-RAPID AND RAPID BURNERS
It is very important to check that the burner
flame distributor “F” and the cap “C” has
been correctly positioned (see figs. 5.25.3) - failure to do so can cause serious
problems.
The internal glass of the oven door can be
easily removed for cleaning by unscrewing
the two lateral fixing screws (fig. 5.1).
CORRECT REPLACEMENT OF THE
TRIPLE RING BURNER
Fig. 5.1
The triple ring burner must be correctly positioned (see fig. 5.6); the burner rib must
be enter in their logement as shown by the
arrow (see fig. 5.4).
The burner correctly positioned must not
rotate (fig. 5.5).
Then position the cap A and the ring B
(figs. 5.5 - 5.6).
13
C
F
S
Fig. 5.2
Fig. 5.3
S
Fig. 5.4
A
B
Fig. 5.5
14
Fig. 5.6
GLASS LID (only for models with
glass lid)
For cleaning purposes, the lid can be easily removed upwards once taken to the
upright position.
Should the hinges slip off, replace them in
their housing being careful that:
• The right housing must receive the
hinge marked “D” while the left housing must receive the hinge marked
“S” (Fig. 5.7)
REGULATING OF THE BALANCE
Lower the lid and check the correct balance.
While opened at 45° it should hang up.
If necessary, register the calibration of the
hinge springs using the screws “R” (fig.
5.7).
Models with glass lid
Do not shut lid when
burner alight.
ATTENTION
Do not lower the glass lid when the
gas burners are still hot or when
the oven is working or still hot.
Do not lay on the glass lid hot pans
and heavy kitchen utensils.
Dry off any liquid whitch may have
spilt on the cover before opening it.
SOME MODELS ONLY
R
D
S
Fig. 5.7
15
Advice for the installer
IMPORTANT
16
•
Cooker installation must only be carried out by QUALIFIED TECHNICIANS and in
compliance with local safety standards. Failure to install the appliance correctly could
invalidate any manufacturer’s warranty.
•
The appliance must be installed in compliance with regulations in force in your country
and in observation of the manufacturer’s instructions.
•
Some appliances are supplied with a protective film on steel and aluminium parts.
This film must be removed before using the cooker.
6
INSTALLATION
The cooker affords class “1” protection against overheating of surrounding surfaces.
The installation conditions, concerning protection against overheating of the surfaces adjacent to the cooker, must conform to Figs. 6.1 and 6.2.
A space of at least 2 cm must be left between the cooker and any adjacent furniture, which
must not exceed the height of the cooktop.
If the cooker is installed adjacent to furniture which is higher than the gas hob cooktop, a
gap of at least 30 cm must be left between the side of the cooker and the furniture.
The veneered syntetical material and the glue used must be resistant to a temperature of
90°C in order to avoid ungluing or deformations.
Curtains must not be fitted immediatly behind appliance or within 500 mm of the sides.
If the cooker is located on a pedestal it is necessary to provide safety measures to prevent
falling out.
The appliance must be housed in heat resistant units.
The walls of the units must not be higher than work top and must be capable of resisting temperatures of 75 °C above room temperature.
Do not instal the appliance near inflammable materials (eg. curtains).
■■
Class 1
450 mm
650 mm
Gas connection made cm
using
0
rubber hose which 5must be
visible and easily inspected
or using rigid or flexible metal
pipe.
500 mm
300 mm
50
cm
m
20 m
m
20 m
Fig. 6.1
Fig. 6.2
17
VENTILATION REQUIREMENTS
The appliance must be installed in compliance with applicable local regulations concerning ventilation and the evacuation of exhaust gases.
Intensive and prolonged use may require extra ventilation, e.g. opening a window,
or more efficient ventilation increasing the mechanical suction power if this is fitted.
CHOOSING SUITABLE SURROUNDINGS
The room where the gas appliance is to be installed must have a natural flow of air so that
the gas can burn (in compliance with applicable local regulations).
The flow of air must come directly from one or more openings made in the outside walls
with a free area of at least 200 cm2 (or refer to applicable local regulations).
The openings should be near the floor and preferably on the side opposite the exhaust for
combustion products and must be so made that they cannot be blocked from either the
outside or the outside.
When these openings cannot be made, the necessary air can come from an adjacent room
which is ventilated as required, as long as it is not a bed room or a danger area (in compliance with applicable local regulations).
In this case, the kitchen door must allow the passage of the air.
DISCHARGING PRODUCTS OF COMBUSTION
Extractor hoods connected directly to the outside must be provided, to allow the products
of combustion of the gas appliance to be discharged (Fig. 6.3).
If this is not possible, an electric fan may be used, attached to the external wall or the window; the fan should have a capacity to circulate air at an hourly rate of 3-5 times the total
volume of the kitchen (Fig. 6.4).
The fan can only be installed if the room has suitable vents to allow air to enter, as described under the heading “Choosing suitable surroundings”.
H min 650 mm
Extractor hood
for products of
combustion
Fig. 6.3
18
Air vent
Electric fan to
extract products
of combustion
Air vent
Fig. 6.4
7
GAS SECTION
GAS INSTALLATION REQUIREMENTS
Important !
•
The walls adjacent to the cooker must be of heat-resistant material.
•
Before installation, make sure that the local distribution conditions (gas type
and pressure) and the adjustment of this appliance are compatible. The appliance adjustment conditions are given on the plate or the label.
•
This appliance must be installed and serviced only by a suitably qualified, registered installer. The installer shall refer to the local standards in force.
•
Failure to install the appliance correctly could invalidate any manufacturer’s
warranty.
This appliance is supplied for use on Natural gas, LPG or Town Gas (check the gas regulation label attached on the appliance).
•
•
•
Appliances supplied for use on Natural gas: they are adjusted for this gas only and
cannot be used on any other gas (LPG or Town gas) without modification.
The appliances are manufactured for conversion to LPG and Town gas.
Appliances supplied for use on LPG: they are adjusted for this gas only and cannot be
used on any other gas (Natural or Town gas) without modification.
The appliances are manufactured for conversion to Natural and Town gas.
Appliances supplied for use on Town gas: they are adjusted for this gas only and cannot be used on any other gas (Natural gas or LPG) without modification.
The appliances are manufactured for conversion to Natural gas and LPG.
If the Natural gas/LPG/Town gas conversion kit is not supplied with the appliance this kit
can be purchased by contacting the After-Sales Service.
19
CONNECTING THE APPLIANCE TO THE GAS SUPPLY
The gas connection must be carried out by an authorised person according to the relevant
standards.
Ensure that the room in which the cooker is to be installed is adequately ventilated, in compliance with applicable regulations.
•
Connect the cooker to the gas mains utilizing rigid or flexible pipes.
•
The gas supply is connected at the rear of the cooker to the terminal of the gas inlet
pipe (Fig. 7.1).
The connection pipe must not cross the rear of the appliance.
IF CONNECTING THE APPLIANCE TO A GAS CYLINDER POSITIONED INSIDE THE GAS
COMPARTMENT, FOLLOW ALSO THE INFORMATION AS PER CHAPTER “GAS CYLINDER
CONNECTION” AND FIGURE 7.4.
ok
THE PIPE DOES NOT CROSS THE REAR PANEL OF THE COOKER.
IN CASE OF CROSSING THE BACK PANEL, ENSURE THE PIPE IS POSITIONED
CLOSE TO THE BOTTOM PART OF THE APPLIANCE.
ok
Fig. 7.1
POSSIBLE GAS CONNECTIONS
GAS CONNECTION WITH A RUBBER HOSE
Important!
A rubber hose connection shall only be made if permitted by the applicable local
regulations.
The gas connection is made up of:
• the terminal fitting of the inlet pipe;
• the brass connector;
• sealing washer/s;
• the appropriate hose holder (for Natural/Town gas or LPG).
Important! If the brass connector is not already fitted on the appliance (but supplied in a separate kit), screw that connector to the terminal of the gas inlet pipe
before starting the connection to the gas supply.
Use two spanners when connecting the brass connector.
20
Connecting the cooker to Natural or Town gas
1. If not already fitted, fit the Natural/Town gas hose holder on the inlet pipe, making sure
that you place the sealing washer between them (as shown in Fig. 7.2).
2. Connect the cooker to the gas supply using a suitable rubber hose (internal diameter 13 mm).
The hose must comply with the applicable local regulations and be of the correct construction for the type of gas being used.
3. Make sure that the hose is tightly and securely fitted at both ends.
4. Use a standard hose clamp (not supplied) to fasten the hose.
Connecting the cooker to LPG
1. If not already fitted, fit the LPG hose holder on the inlet pipe, making sure that you
place the sealing washer between them (as shown in Fig. 7.2).
Important! The LPG hose holder is composed by Natural/Town gas hose holder with LPG hose adapter screwed at the bottom end (interposing the proper
sealing washer between them).
2. Connect the cooker to the gas supply using a suitable rubber hose (internal diameter
8 mm).
The hose must comply with the applicable local regulations and be of the correct construction for the type of gas being used.
3. Make sure that the hose is tightly and securely fitted at both ends.
4. Use a standard hose clamp (not supplied) to fasten the hose.
5. Install a gas pressure regulator.
Important! To comply with applicable local regulations, a gas pressure regulator
(conforming to the local regulations in force) must be installed when connecting the
cooker to an LPG cylinder.
When connecting the cooker to the gas supply with a rubber hose, make sure that
the hose is as short as possible, without twists or kinks.
the hose is not longer than 750 mm (or refer to applicable local regulations) and does
not come into contact with sharp edges, corners or moving parts. Use a single rubber
hose only; never connect the appliance with more than one rubber hose.
• the hose is not under tension, twisted, kinked, or too tightly bent, neither while the
appliance is in use nor while it is being connected or disconnected.
• the hose does not come into contact with any part of the cooker with a surface temperature of 70°C or above (or refer to applicable local regulations).
• the hose is not subject to excessive heat by direct exposure to flue products or by
contact with hot surfaces.
• the hose can easily be inspected along its entire length to check its condition.
• the hose is replaced at the printed due date or if it shows signs of wear or damage, and
replaced regardless of its condition after a maximum of three years.
• you inform the customer that the gas cylinder valve or the gas supply valve immediately by the cooker should be closed when the cooker is not in use.
• you inform the customer that the hose should not be subjected to corrosion by acidic
cleaning agents.
•
•
After connecting the cooker to the gas supply, make sure that you
• check that the connections are correctly sealed using a soapy solution, but never a
naked flame.
• check whether the injectors are correct for the type of gas being used. If not, follow the
instructions under “GAS MAINTENANCE”.
• replace the sealing washer/s on the slightest sign of deformation or imperfection. The
sealing washer/s is/are the part/s which guarantees a good seal in the gas connection.
• use two spanners when fitting the parts (Fig. 7.2).
21
Gas connection with rubber hose holders
Note: if not already fitted on the inlet pipe,
the hose holders are supplied with the product in a separate kit.
Inlet pipe
Manifold male
pipe fitting
1/2” G cylindrical
(ISO 228-1) male
Sealing washer (#)
1/2” G cylindrical
(ISO 228-1) female
Brass connector (#)
1/2” G cylindrical
(ISO 228-1) male
Sealing washer (#)
1/2” G cylindrical
(ISO 228-1) female
Hose holder for Natural/Town gas
(#) If not already fitted on the inlet
pipe, it is supplied with the
appliance in a separate kit
1/2” G cylindrical
(ISO 228-1) female
Hose holder for Natural/Town gas
LPG hose adapter sealing washer
Hose clamp (not supplied)
Hose adapter for LPG
Hose clamp (not supplied)
Rubber hose (not supplied) for LPG
connection (internal diameter 8 mm)
LPG
Rubber hose (not supplied) for
Natural/Town gas connection
(internal diameter 13 mm)
Natural or Town gas
Fig. 7.2
GAS CONNECTION WITH RIGID PIPES OR A FLEXIBLE PIPE
The gas connection is made up of:
• the terminal fitting of the inlet pipe;
• the brass connector;
• sealing washers.
Important!
■■
■■
If fitted, remove the hose holder from the terminal fitting of the inlet pipe.
If the brass connector is not already fitted on the appliance (but supplied in a
separate kit), screw that connector to the terminal of the gas inlet pipe before
starting the connection to the gas supply.
Use two spanners when connecting the brass connector.
When connecting the cooker to the gas supply with rigid pipes or a flexible pipe, make
sure that
• you use rigid pipes or a flexible pipe complying with applicable local regulations. The
flexible pipe shall be of the correct construction for the type of gas being used.
• if compression fittings are used, you tighten them firmly using two spanners (Fig. 7.3).
• the connection with rigid metal pipes does not cause stress or pressure to the gas piping.
• the flexible pipe is not under tension, twisted, kinked or too tightly bent, neither while the
appliance is in use nor while it is being connected or disconnected.
22
•
•
•
•
•
•
•
•
the flexiple pipe does not exceed 2000 mm in length (or refer to applicable local regulations) and does not come into contact with sharp edges, corners or moving parts. Use
a single flexible pipe only; never connect the cooker with more than one flexible pipe.
the flexible pipe can easily be inspected along its entire length to check its condition; if it
has an expiry date, it should be replaced before that date.
if using a flexible pipe which is not entirely made of metal, make sure that it does not
come into contact with any part of the cooker with a surface temperature of 70°C or
above (or refer to applicable local regulations).
the hose is not subject to excessive heat by direct exposure to flue products or by contact with hot surfaces.
the rigid or flexible pipe is replaced if it shows signs of wear or damage.
a gas pressure regulator, in compliance with the applicable local regulations, is installed
when connecting to an LPG cylinder.
you inform the customer that the cylinder valve or the supply valve immediately by the
appliance should be closed when the cooker is not in use.
you inform the customer that the rigid or flexible pipe should not be subjected to corrosion by acidic cleaning agents.
After connecting the cooker to the gas supply, make sure that you
• check that the connections are correctly sealed using a soapy solution, but never a
naked flame.
• check whether the injectors are correct for the type of gas being used. If not, follow the
instructions under “GAS MAINTENANCE”.
• replace the sealing washer/s on the slightest sign of deformation or imperfection. The
sealing washer/s is/are the part/s which guarantee/s a good seal in the gas connection.
• use two spanners when connecting the rigid or flexible pipe (Fig. 7.3).
Gas connection with rigid or flexible pipe
Note: if already fitted on the inlet pipe,
remove the rubber hose holder
Inlet pipe
Manifold male
pipe fitting
Sealing washer (#)
1/2” G cylindrical
(ISO 228-1) male
1/2” G cylindrical
(ISO 228-1) female
Brass connector (#)
1/2” G cylindrical
(ISO 228-1) male
(#) If not already fitted on the inlet
pipe, it is supplied with the
appliance in a separate kit
Sealing washer (#)
1/2” G cylindrical
(ISO 228-1) female
Flexible pipe
(not supplied)
1/2” G cylindrical
(ISO 228-1) female
Rigid pipe
(not supplied)
Fig. 7.3
23
GAS CYLINDER CONNECTION
The connection between the hose connector on the cooker and the regulator of the
gas cylinder must be made using a 60 cm
long flexible hose conforming to applicable
standards, and hose clamps.
The connection hose must be inserted in
the hose support (fig. 7.4) and pushed over
the hose connectors to the full depth.
IMPORTANT:
Only 13 kg maximum cylinders may be
used in the cylinder compartment, and they
must be positioned in such a way that the
regulator and shut-off cock are easily accessible.
When changing the gas cylinder, do not
withdraw the hose from the support.
Installation and replacement of gas
cylinders must only be carried out by
qualified persons.
Hose
clamp
Pressure
regulator
Hose
support
Hose length:
60 cm
Gas cylinder:
13 kg maximum
24
Hose
clamp
Fig. 7.4
GAS MAINTENANCE
TABLE FOR THE CHOICE OF THE INJECTORS
0,75
0,45
93
87
66
Ø injector
[1/100 mm]
-
-
-
Ring
opening
[mm]
135
129
101
Ø injector
[1/100 mm]
5 (*)
-
-
-
Ring
opening
[mm]
270
310
280
192
Ø injector
[1/100 mm]
5 (*)
-
-
-
Ring
opening
[mm]
Town Gas
G110 8 mbar
1,75
1,50
130
Natural Gas
G20 20 mbar
3,00
Fully open(*)
LPG
G30 28-30 mbar
G31 37 mbar
Semi-rapid (SR)
3,50
86
Reduced
power
[kW]
Rapid (R)
0,85
Nominal
power
[kW]
Triple-ring (TR)
3,20
BURNERS
Oven
(*) = Reference value
AIR VENT NECESSARY FOR GAS COMBUSTION = (2 m3/h x kW)
7,00
6,00
3,50
Air necessary for combustion [m3/h]
Rapid (R)
6,40
Semi-rapid (SR)
BURNERS
Triple-ring (TR)
In case of difficulty in the gas taps operation, call Service.
•
Oven
LUBRICATION OF THE GAS TAPS
IMPORTANT
25
All intervention regarding installation maintenance of the appliance must be fulfilled with
original factory parts.
The manufacturer declines any liability resulting from the non-compliance of this obligation.
REPLACEMENT OF THE INJECTORS
If the injectors are not supplied they can
be obtained from the “Service Centre”.
Semi-rapid and
rapid burners
J
Select the injectors to be replaced according to the “Table for the choice of the
injectors”.
The nozzle diameters, expressed in hundredths of a millimetre, are marked on the
body of each injector.
REPLACEMENT OF THE INJECTORS OF THE COOKTOP BURNERS
Fig. 7.5a
To replace the injectors proceed as follows:
•
Remove pan supports and burners
from the cooktop.
Triple-ring burner
•
Using a wrench, substitute the nozzle
injectors “J” (figs. 7.5a - 7.5b) with those most suitable for the kind of gas for
which it is to be used.
J
The burners are conceived in such a
way so as not to require the regulation
of the primary air.
ADJUSTING OF THE MINIMUM OF
THE COOKTOP BURNERS
Fig. 7.5b
In the minimum position the flame must
have a length of about 4 mm and must remain lit even with a quick turn from the maximum position to that of minimum.
The flame adjustment is done in the following way:
26
•
Turn on the burner.
•
Turn the tap to the MINIMUM position.
•
Take off the knob.
•
With a small flat screwdriver turn the
screw inside the tap rod to the correct
regulation (fig. 7.6).
Normally for G30/G31 (LPG), tighten up
the regulation screw.
Fig. 7.6
OPERATIONS TO BE EXECUTED
FOR THE REPLACEMENT OF THE
INJECTOR OF THE OVEN BURNER
•
Lift and remove the lower panel inside
the oven.
•
Remove the burner securing screw
(fig. 7.7).
•
Withdraw the burner as shown in figure 7.8 and rest it inside the oven.
Take care not to damage the wire to
the safety valve probe.
•
Using a 7 mm box spanner, unscrew
the injector (indicated by the arrow in
fig. 7.8) and replace it by the proper
one according to the kind of gas.
•
Then replace the burner repeating the
above steps in reverse order.
Fig. 7.7
PRIMARY
BURNER
AIR
OF
THE
OVEN
With a screwdriver untighten the two screws
(fig. 7.9) and move forward or backward
the air ring to close or open the air flow,
according to the “Table for the choice of the
injectors”.
Light the burner and check the flames.
Fig. 7.9
Ring opening
Fig. 7.8
27
Flame faulty
in primary
air
Flame
correct
Flame with
excess
primary air
long, yellow
and trembling
clear interior
blue cone
short and sharp
too blue interior
cone tending to
detach
air regulating
tube, too
closed
correct distance of the
tube
CAUSE
air regulating
tube, too
open
ADJUSTMENT OF THE OVEN BURNER MINIMUM
Considering that in the minimum position
the flame must have a length of about 4
mm and must remain lit even with a brusque passage from the maximum position
to that of minimum.
The flame adjustment is done in the following way:
•
•
Flame
correct
Flame faulty
in primary air
Flame with
excess
primary air
•
•
turn on the burner by setting the thermostat knob on position 10 (maximum.);
remove the knob and unscrew the bypass screw “G” (fig. 7.10) about three
times by passing a small flat screwdriver (Ø 3 mm blade, 100 mm length)
through the panel opening;
re-mount the knob and let the oven
heat up for about 10 minutes, then
bring the knob to position 1 (minimum)
to operate the thermostat by-pass;
after having removed the knob again
and being very careful not to turn the
tap rod, slowly screw the by-pass
screw “G” (fig. 7.10) until you obtain a
flame of 3-4 mm in height.
Normally for LPG (G30/G31), tighten up
the regulation screw.
G
Fig. 7.10
28
8
BATTERY INSTALLATION
INSTALLING THE BATTERY
Insert a type C battery (1.5 Volt) into he
battery compartment on the back of the cooker (fig. 8.1).
This battery is the power supply for the
electronic ignition of gas burners (cooktop
burners only).
Batteries last on average for about two years (alkaline battery) depending on how often the electronic ignition is used.
Notes for battery installation or replacement:
•
Only use a type C 1.5 Volt battery.
•
Check for correct polarity (fig. 8.2 and
label to the side of the battery compartment).
Fig. 8.1
Important notes:
•
Remove the battery if the cooker is not
going to be used for a long time.
•
If the battery leaks, replace it immediately. Avoid touching the leaked liquid
and make sure it does not come into
contact with clothes or other items.
•
Clean the battery compartment carefully before installing the new one.
•
Note: The battery is a potential source
of danger for children. Keep them
away.
•
Dispose of flat batteries properly.
1,5 V
Fig. 8.2
29
30
31
The manufacturer cannot be held responsible for possible inaccuracies due to printing or transcription errors in the
present booklet.
The manufacturer reserves the right to make all modifications to its products deemed necessary for manufacturer
commercial reasons at any moment and without prior notice, without jeopardising the essential functional and safety
characteristics of the appliances.
HOME APPLIANCES
Made in Italy
Cod. 1104228- ß1
Download PDF