E-Tech | ET8 | User`s manual | E-Tech ET8 User`s manual

E-TECH ET8 ALARM CONTROL PANEL AND DIALLER
USER’S MANUAL
E-TECH ET8 CONTROL PANEL V4 – USER’S MANUAL, REVISION 1
A$12.00 INC GST
Versions commencing November 2001
Quality
Endorsed Fictional
Company
ISO9001
E-Tech Security Products Pty Ltd
“Australia’s largest
designer and
manufacturer of
high quality
security products”
HEAD OFFICE:
E-Tech Security Products Pty Ltd
ABN 000 110 110
12 Security Close
Safe Hills NSW 2147 Australia
Ph
+61 23 9988 7766
Fax
+61 23 9988 7765
ET8 V4 INSTALLER MANUAL
Revision 1, November 2001
E-TECH SECURITY PRODUCTS
Australian Communications Authority
TELECOMMUNICATIONS COMPLIANCE
Document Part Number: 890–265
For product:
100–191 ET8 LED Control Panel (V4)
100–688 ET8 LCD Control Panel (V4)
© 2001 E-Tech Security Products Pty Ltd ACN 000 110 110
ET8 V4 installer
Specifications may change without notice.
LIC.No. QEC2074
NSW Head Office only
CONTENTS
Features ...................................................................... 4
Introduction ................................................................. 5
Keypad ........................................................................ 6
Keypad Indicators ...................................................... 7
OPERATION by KEYPAD ........................................... 8
Arming ...................................................................... 9
Disarming .............................................................. 10
Resetting Alarms ................................................... 10
Monitor Mode ........................................................ 11
Panic ...................................................................... 12
Duress .................................................................... 12
Fire Alarm .............................................................. 13
Medical Alarm ....................................................... 13
Excluding Zones ................................................... 14
Alarm Memory ....................................................... 15
OPERATION by RADIO KEY ..................................... 16
PROGRAMMING ....................................................... 17
Programming Options Table ................................ 17
User Code programming ...................................... 18
Entry/Exit Timer programming ............................. 18
Telephone Number programming ....................... 19
Monitoring, Central Station ...................................... 20
Monitoring, Audible .................................................. 21
Wireless Accessories ............................................... 20
Remote Operation by Telephone ............................ 22
E-TECH ACCESSORIES ......................................... 24
Wireless Accessories ........................................... 25
Troubleshooting ........................................................ 26
Installation Record .................................................... 27
OPERATION SUMMARY .......................................... 28
E-TECH ET8 FEATURES
•
8 Fully programmable zones
•
Any combination of hardwire or radio
zones
•
•
Comes complete with an AC plug
pack and supports a 12V 7Ah
battery to maintain systems security
under all power supply conditions
Full radio supervision
•
Monitor Mode (Home Mode)
•
Contact ID Dialler Format
•
Outputs are separately fused with
Automatic Reset Fuses
•
Ultra-Modern and Impact resistant
Housing
•
Day Mode and Door Chime feature.
•
E-Tech Audible Dialler Format
•
30 Event Memory
•
"Follow Me" Audible Dialler Option
•
•
Separate 24 Hour Tamper input
Supports 8 Radio Devices (Radio
PIRs, Radio Reeds etc)
•
Single or Double Trigger Zones
•
Supports 14 Radio Keys
•
•
Remote LED or LCD Keypads (Max 3)
•
Fully programmable via the system
Keypad - Eliminates the need for
expensive programmers or Proms.
All inputs and outputs are heavily
protected against lightning and high
voltage supply transients. An earth
terminal is provided for extra protection
•
Inbuilt Vibration Sensor Analyser
•
15 User Codes
•
All programming data is permanently
stored in a non-volatile EEprom
memory
•
‘Arm only’ codes can be programmed
•
Programmable Inputs to activate
selectable Outputs
•
Designed utilising the latest SMD
Technology
•
Simple to Program and Use.
•
Windows based Up\Down load
Software allows remote programming
and event status
•
True Dynamic Battery Test every time
the Panel is armed / disarmed and
every hour
•
Area Partitionable (2 Areas). Any Zone
can be programmed to any area, as
well as common areas
4
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
INTRODUCTION
The E-Tech ET8 micro computer based 8 zone
control panel is the heart of your security
system to which all your detection devices
connect.
Arming the system may be done through the
keypad or with the use of optional Radio Keys
for Arming by remote control from outside the
premises.
Each Zone of the panel can be connected to
one or more detection devices to protect
separate rooms of your premises.
When you enter the premises the panel will
ignore selected zones for the Entry Delay Time
and will not alarm unless you don’t Disarm the
panel during this allowed time.
Detection devices may be connected to the
ET8 control system directly by cabling or with
optional wireless (Radio) devices.
Detection devices called Passive Infra-Red
Detectors (or P.I.R’s for short) can detect the
movement of an intruder by sensing their body
heat. P.I.R’s are used to cover various critical
areas of your premises where an intruder may
enter or trespass. Another detection device used
is called a Reed Switch. Reed Switches are
attached to windows and doors to detect if a
window or door has been opened. A Reed
Switch consists of a magnet which is normally
attached to the moving part of a window or door
and the Reed switch which mounts to the door
or window frame.
The panel is “Armed” when it is set to detect an
intruder. At other times it is “Disarmed”.
Normally a zone is considered Sealed.
Activation of a detection device will cause the
zone to be Unsealed and may cause an alarm.
Detectors such as fire detectors and panic
buttons must be able to generate an alarm at all
times regardless of the panel setting. A zone
with this assignment is called a 24 hour zone.
Some detection devices may be required to
generate an alarm or warning only when the
panel is Disarmed. A zone with this assignment
is called a Day zone.
Before leaving the premises you must Arm the
panel to enable it to detect intruders and
generate an alarm. After arming, the panel will
ignore detectors during the Exit Delay Time to
enable you to depart without triggering an alarm.
Disarming the system may be done by keypad
or with the use of optional Radio Keys.
Monitor mode allows you to Arm selected zones
while others are ignored. Typically, perimeter
zones (doors and windows) can be monitored
while you are at home.
If you wish to split your alarm system into two
areas with access limited to each area by code
numbers then Area operation is used. Radio
Keys can also Arm and Disarm Areas.
The control panel housing and the covers over
external sirens are protected by tamper
switches to detect someone attempting to
disable the security system. Activation of these
switches will cause an instant tamper alarm.
If a detector becomes faulty, you can Exclude
the associated zone so that it is totally ignored
and cannot generate an alarm. Including the
zone will enable it to generate an alarm again.
The control panel is fitted with a rechargeable
stand-by battery to ensure your security system
continues to operate if the mains power is
interrupted. This control panel automatically
tests the battery every hour and whenever you
Arm/Disarm the panel. (Dynamic Battery test).
Whenever an alarm occurs, it may be silenced
with a User Code or by optional Radio Keys,
otherwise it will reset at the end of Alarm Reset
Time.
All alarms are stored in memory and may be
viewed at any time by entering Memory Mode.
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
5
KEYPAD
The ET8 control panel may be supplied with either the LED keypad (100-192) or the E-Tech LCD
Keypad (100-667).
The keypad provides important visual and audible indications and is the main interface for operating
and programming the ET8 control panel.
105mm
90mm
LED KEYPAD
LCD KEYPAD
Backlit LCD
icon display
MEMORY button
PANIC buttons
PANIC
MEMORY
ARM button
ARM
1
2
3
MONITOR button
MONITOR
4
5
6
EXCLUDE button
EXCLUDE
7
8
9
PROGRAM button
PROGRAM
0
ENTER button
Not Ready
PANIC buttons
ARM
1
2
3
MONITOR button
MONITOR
4
5
6
EXCLUDE button
EXCLUDE
7
8
9
MEMORY button
MEMORY
P
0
E
ARM button
PANIC
ENTER
PROGRAM button
ENTER button
Protective flap not shown
Protective flap not shown
The “Not Ready” light is on when the panel is not ready to Arm.
i.e, a zone is unsealed, there may still be movement in the
premises or a door or window left open
DISPLAY TEST (LCD Keypad only)
To display all the keypad icons press and hold
the
button for at least 2 seconds. All the
icons will be on whilst the
button is held
down.
Display Test can be activated at any time either
in operating mode or any program mode.
6
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
135mm
150mm
“Not Ready” light
KEYPAD INDICATORS
LED KEYPAD
STATUS
LCD KEYPAD
ZONES 1~8
OFF
ON
Zone is sealed
Zone is unsealed
READY
Zone is unsealed, or Power fault
or System is Armed,
or phone line fault
Ready to Arm
ARMED
Disarmed
Armed (AREA 1)
ARM2
Disarmed
Armed (AREA 2)
Disarmed
Monitor Mode
FLASHING
Zone alarm
Monitor Mode
(LED Keypad only)
MAINS
Normal
Mains Power is off
BATTERY
Normal
The panel’s backup
battery is low
MEMORY
Normal
EXCLUDE
Normal
Zones are excluded
TAMPER
Normal
Tamper alarm
RADIO
Normal
(And in Memory Mode indicates a
low battery alarm from a radio device)
Indicates that a Radio Key or
other radio device has a
low battery
LINE
Normal
Dialler is on line
Phone line fault or
failure to communicate
PROGRAM
Normal
User Program Mode
Installer Program Mode
Ready to Arm
Not ready to Arm
Not Ready
Memory Mode selected
Receiving radio signal
New alarms in memory
KEYPAD BEEPER SOUNDS
Each key press
1 beep
Valid command
3 beeps
Error
1 long beep
Mains Power is off
or
Panel Battery is low
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
10
10 beeps
7
OPERATION
This section describes the operation of a
USER CODE ASSIGNMENT
typical control panel installation. Keep in
A User Code assigned to an Area can Arm and
Disarm only that Area. User Codes assigned to
both Areas will operate both Areas
simultaneously.
mind that your installation may vary
depending on the selected options and
equipment. The operating instructions which
follow will cover the most common options.
Consult your installation company if you
require further information.
All control panel operations are controlled by
the ET8 LED or LCD keypad except if an
optional key switch or radio control equipment
is installed.
OPERATING RULES
Generally, the panel will be Disarmed. Armed
or Monitor modes provide different levels of
security for your premises when you are home
or away. Three other temporary modes;
Program, Memory and Exclude, allow you to
perform various operations. The panel will
automatically exit from these temporary modes
if you do not press any buttons on the keypad
in a 4 minute period.
If you make a mistake while entering any codes,
press the Enter or E button and start again.
When you are required to enter your access
code, you are given five opportunities to enter it
correctly. After the fifth invalid attempt the alarm
is activated (requiring the correct code to silence
the alarm). This prevents anyone trying to guess
your code by entering random numbers.
COMMON AREA ZONES
Zones assigned to both Areas are Armed only
when Area1 and Area2 are both Armed. This
allows the Common Area zone/s to be shared
by both Areas.
For example, Office A and Office B operate as
separate areas but the entrance foyer used by
both offices is assigned to both areas meaning
it will automatically Arm when both Areas have
Armed. The Common Area then automatically
disarms when either Area1 or Area2 Disarms.
OPERATION
Arming and Disarming is carried out as normal
from a single keypad or separate keypads
installed in both areas or by Radio Key.
Area operation only applies to zones when they
are in the Armed state. This means that Day,
24hr and Monitor zones are independent of the
area operations.
Note: Area partitioning is in addition to Monitor
Mode. Any zone may be allocated to any area.
AREA OPERATION
Area Partitioning allows the 8 zones to be split
into two partitions; Area1 and Area2.
The panel then effectively operates as two
separate systems sharing only the siren outputs
and dialler.
8
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
OPERATION
ARMING
LCD KEYPAD
LED KEYPAD
The Ready light must be on
Press...
or...
ARM
ARM
The Not Ready light must be off
ENTER
[User Code]
Press...
ENTER
The Armed light will turn on
• Leave the premises within the Exit Delay Time
• 3 beeps will sound at the end of Exit Delay Time
The control panel must be Armed prior to
vacating the premises in order to detect
intruders. Ensure that the panel is not in
Program, Memory or Exclude modes.
Note: If the panel is already in alarm, you must first
silence the alarm before you can Arm.
If something is wrong when Arming the control
panel, the normal 3 beeps will be replaced by
other warnings.
10
10 beeps means Mains Power is
turned off or the Backup Battery is low.
or...
[User Code]
The
icon will turn on
• Leave the premises within the Exit Delay Time
• 3 beeps will sound at the end of Exit Delay Time
SIREN WARNING:
At the end of the exit time, all zones should be
Sealed. If any are Unsealed, the siren will sound
for 2 seconds as a warning to indicate that those
zones have been automatically excluded. For
maximum security, you should return, Disarm,
check the premises and then Arm again.
Continual warnings could mean that a detector
is faulty and may have to be manually excluded.
If the auto-exclude option is disabled, the siren
will sound for the duration of reset time if a zone
is Unsealed at the end of exit time.
One long beep indicates an invalid
entry or an alarm is outstanding and needs to
be reset by entering your User Code first.
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
9
OPERATION
DISARMING
LCD KEYPAD
LED KEYPAD
Enter the premises through a delay zone
Enter the premises through a delay zone
Press... [User Code]
Press... [User Code]
The
ENTER
Armed light will turn off
When you enter the protected premises through
a delay zone, the keypad responds with regular
beeps* as a reminder to Disarm. You then have
your programmed entry delay time to Disarm
the panel by entering one of your user codes. If
the panel is not Disarmed by the end of the entry
delay time, an alarm will occur.
By using the optional radio keys you may
Disarm your system from within your premises
The
icon will turn off
or from outside your entrance door. There is also
the option to ‘Chirp’ the outside siren three times
and to flash the strobe light for two seconds as
an indication that you have Disarmed your
system.
If you make a mistake in entering your code,
then you must press enter and start again. Five
incorrect entries will cause an alarm.
* If Entry Beeps are programmed on.
RESETTING ALARMS
ALARMS, DEFINITION
Your panel can be reset and the alarm silenced
by the same key sequence as Disarming the
panel.
Alarms may be caused by:
If you arrive at your premises and find the strobe
light flashing (if installed), reset the panel as
above. To check the cause of the alarm, you
can view the alarms in memory by entering
Memory Mode.
10
• A zone has been triggered while Armed
• A Tamper has been triggered
• A PANIC button has been triggered
All of these may cause your sirens and strobe
to operate. Various visual indications relevant
to the alarm will be retained in the memory. If
this occurs, Disarming your control panel will
reset the alarm. The cause of the alarm can be
identified by entering the Alarm Memory Mode
as described on page 15.
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
OPERATION
MONITOR MODE
LCD KEYPAD
LED KEYPAD
Press...
or...
MONITOR
MONITOR
ENTER
[User Code]
Press...
ENTER
The Monitor light will turn on
• Only the zones which have been programmed
by your installer as Monitor zones will be Armed
or...
[User Code]
The
MONITOR icon will turn on
• Only the zones which have been programmed
by your installer as Monitor zones will be Armed
Monitor mode allows you to Arm selected zones
while others are ignored. Typically, perimeter
zones (doors and windows) can be monitored
while you are at home.
If an alarm occurs while in Monitor mode,
Your installer must program which zones will be
active in Monitor mode.
By using the optional Radio Keys you can enter
Monitor Mode by pressing the OFF button twice
within 4 seconds. (Your installer must enable
Radio Key Monitor Arming for this to work).
The panel must be fully Disarmed before Arming
in Monitor Mode.
entering [User Code]
will silence the alarm.
This will also Disarm the panel, so remember to
enter monitor again if needed.
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
11
OPERATION
KEYPAD PANIC
LCD KEYPAD
LED KEYPAD
Press...
or...
PANIC
PANIC
or...
PANIC
PANIC
Both keys together
[User Code]
ENTER
Press...
Both keys together
or...
[User Code]
or...
ENTER
(If Keypad Panic Shortcut has been enabled by your installer)
The keypad PANIC function may have been
programmed to be either AUDIBLE - activates
siren or buzzers, or SILENT - If your system is
monitored by a Central Station, sends a PANIC
report by dialler. (If PANIC reports have been
enabled by your installer).
(If Keypad Panic Shortcut has been enabled by your installer)
PANIC cannot be used while the panel is in
Program, Memory or Exclude mode.
Note: Your installer may have installed a separate
PANIC button. To activate the panic alarm simply
press that button.
KEYPAD DURESS ALARM
LCD KEYPAD
LED KEYPAD
Press...
9
Press...
[User Code]
[User Code]
Disarms and sends a Duress Alarm report by dialler.
Disarms and sends a Duress Alarm report by dialler.
1. If your system is monitored by a central monitoring station
2. If Duress Alarm Report has been enabled by your installer
1. If your system is monitored by a central monitoring station
2. If Duress Alarm Report has been enabled by your installer
Duress Alarm can be programmed to sound
the RESET output.
1. By default, Duress Alarm does not sound the RESET output
Digits 5, 6 & 8 in front of the user code can also
be used trigger the Duress alarm
A DURESS alarm can be triggered to alert the
Central Station that you are being forced to
Disarm the panel against your will.
To Disarm and send a DURESS alarm, prefix
your User Code with one of the digits 5, 6, 8 or
9 when Disarming.
12
Duress Alarm can be programmed to sound
the RESET output.
1. By default, Duress Alarm does not sound the RESET output
Digits 5, 6 & 8 in front of the user code can also
be used trigger the Duress alarm
DURESS alarms are only used if your system is
monitored by a Central Station.
DURESS IS NORMALLY NOT ENABLED. TO
ENABLE THE DURESS FUNCTION, CONSULT
YOUR INSTALLER
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
OPERATION
KEYPAD FIRE ALARM
LCD KEYPAD
LED KEYPAD
Press...
Press...
Sounds the siren (Fire Alarm siren sound)
Sounds the siren (Fire Alarm siren sound)
1. If Keypad Fire Alarm has been enabled by your installer
Sends a Fire Alarm report by dialler.
1. If your system is monitored by a central monitoring station
2. If Fire Alarm Report has been enabled by your installer
1. If Keypad Fire Alarm has been enabled by your installer
Sends a Fire Alarm report by dialler.
1. If your system is monitored by a central monitoring station
2. If Fire Alarm Report has been enabled by your installer
KEYPAD MEDICAL ALARM
LCD KEYPAD
LED KEYPAD
Press...
Press...
Sends a Medical Alarm report by dialler.
Sends a Medical Alarm report by dialler.
1. If your system is monitored by a central monitoring station
2. If Medical Alarm Report has been enabled by your installer
Medical Alarm does not sound sirens.
1. If your system is monitored by a central monitoring station
2. If Medical Alarm Report has been enabled by your installer
Medical Alarm does not sound sirens.
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
13
OPERATION
EXCLUDING ZONES
LCD KEYPAD
LED KEYPAD
ENTER
Press...
or...
The
[User Code]
Press...
or...
ENTER
Exclude light will turn on
[User Code]
The
EXCLUDE icon will turn on
Enter the zone number of the zone/s to be Excluded
Enter the zone number of the zone/s to be Excluded
[Zone No.]
[Zone No.]
ENTER
[Zone No.]
ENTER
The zone light of each Excluded zone will turn on
Press...
The
ENTER
to exit Exclude mode
Exclude light will flash continuously
If a detector becomes faulty and cannot be
Sealed when arming the panel, then its zone
may be Excluded so that it does not generate
alarms.
When zones have been Excluded, the EXCLUDE
light flashes continuously while the panel is
Disarmed and also when Armed.
[Zone No.]
The zone light of each Excluded zone will turn on
Press...
The
to exit Exclude mode
EXCLUDE icon will flash continuously
Zone Exclude IS not permanent. Excluded
zones are automatically INCLUDED next time the
panel is Disarmed.
Zones can be manually included by the same
method as Excluding. Simply use the
sequence to turn OFF the
[ZONE NUMBER]
zone lights to be Included.
Zones can only be Excluded when the panel is
Disarmed.
NOTES
• EXCLUDE E works only when the panel is Disarmed.
• EXCLUDE [User Code] E works in any state.
• EXCLUDE [User Code] E can only exclude the zones in the Area assigned to that code.
14
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
OPERATION
VIEWING EVENT MEMORY
LCD KEYPAD
LED KEYPAD
ENTER
Press...
or...
The
[User Code]
Press...
or...
ENTER
Memory light will turn on
The
[User Code]
MEMORY icon will turn on
Press...
Press...
The most recent event will be displayed
The most recent event will be displayed
Press...
Press...
The next most recent event will be displayed
The next most recent event will be displayed
Press...
Press...
...and so on (up to 30 events)
...and so on (up to 30 events)
Press...
ENTER
to exit Memory mode
The ET8 Control Panel stores a comprehensive
Alarm Memory, including Arming, Disarming,
Low Battery, Mains Fail and Alarm events.
The memory is constantly upgraded and the last
30 events are always available for viewing.
This Memory display can only be selected while
the panel is in the Disarmed state.
Press...
to exit Memory mode
TO CLEAR THE MEMORY LIGHT
The MEMORY light flashes continuously when
an alarm has occurred as a reminder to view
the alarm memory.
The MEMORY light stops flashing after the
memory is viewed as shown above.
The MEMORY light is automatically cleared
next time the panel is Armed.
MEMORY MODE - EVENTS INDICATED BY KEYPAD LIGHTS:
LIGHT
Zone lights 1~8
ARM
(no lights)
TAMPER
EXCLUDE
BATTERY
MAINS
RADIO, BATTERY, ZONE
RADIO, BATTERY, ARM
ALARM EVENT
Zone alarm
Panel Armed
Panel Disarmed
Tamper alarm (Siren cover, panel etc)
Panic alarm
Low Battery
Mains power failure
Radio Device battery low
Radio Key battery low
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
15
RADIO KEY OPERATION
E-TECH RADIO KEY 3 BUTTON
The optional E-Tech Radio Key allows you to Arm, Disarm and
activate PANIC. The Radio Key can also Arm Monitor Mode, (if this
has been enabled by your installer).
ARMING
Press the ON button.
• The keypad will give 3 beeps.
• The outside siren will give 1 ‘chirp’. (If enabled by your installer)
• The strobe light will flash briefly
DISARMING
Press the OFF button.
• The keypad will give 3 beeps.
• The outside siren will give 3 ‘chirps’. (If enabled by your installer).
• The strobe light will flash briefly.
ARMING MONITOR MODE
Press the OFF button twice within 4 seconds.
• The keypad will give 9 beeps.
• The outside siren will NOT ‘chirp’.
• The strobe light will flash briefly.
PANIC
Press and hold the PANIC button for at least 4 seconds.
• The siren and strobe will activate, (If enabled by your installer)
• The dialler will report a Panic alarm, (If enabled by your installer
and if your system is monitored by a central station).
Press the OFF button to reset a Panic alarm
* The E-Tech Radio Key is optional and is not supplied with any E-Tech control panels as standard
* E-Tech radio products require a E-Tech Radio Interface (100-200) to be fitted to the control panel.
16
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
PROGRAMMING
Various system options, as listed below, can
be programmed by the user. These options
can only be accessed from Program Mode.
User Codes may need to be re-programmed
if a person has forgotten their code, to give a
new user access to the system or to give
someone temporary access.
User Codes 2-15 can be set as Arm Only
Codes. These codes can Arm but cannot
Disarm the panel. (Useful for assigning to
cleaners, tradesmen etc.)
You may need to change the Entry and Exit
timers if you find the delays are too long or
short.
If Audible Monitoring is programmed by your
installer, the ‘Follow Me’ Telephone Number is
the telephone number the dialler will call in the
event of an alarm.
If your E-Tech ET8 panel is monitored by a
Central Station, the Follow Me number is
ignored.
For all other programming changes, talk to
your installer.
The panel will automatically exit Program
Mode is no buttons are pressed within a 4
minute period.
FACTORY DEFAULT MASTER CODE IS: 123
PROGRAMMING OPTIONS TABLE
OPTION No
FACTORY
DEFAULT
User Code 1 (Master Code)
P11E
123
User Code 2
P12E
3 to 6 digits
User Code 3
P13E
3 to 6 digits
User Code 4
P14E
3 to 6 digits
User Code 5
P15E
3 to 6 digits
User Code 6
P16E
3 to 6 digits
User Code 7
P17E
3 to 6 digits
User Code 8
P18E
3 to 6 digits
User Code 9
P19E
3 to 6 digits
User Code 10
P20E
3 to 6 digits
User Code 11
P21E
3 to 6 digits
User Code 12
P22E
3 to 6 digits
User Code 13
P23E
3 to 6 digits
User Code 14
P24E
3 to 6 digits
User Code 15
P25E
Entry Delay 1
P26E
20 seconds
1 to 99 sec
Entry Delay 2
P27E
60 seconds
10 to 990 sec
Exit Delay
P28E
60 seconds
1 to 99 sec
Follow Me Telephone No.
P00E
OPTION
RANGE
PROGRAMMED
3 to 6 digits
3 to 6 digits
Up to 15 digits
NOTE: The Entry Delay 2 timer programs in 10 second intervals.
Example: if a value of 6 is programmed, the time is 60 seconds.
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
17
PROGRAMMING
PROGRAMMING USER CODES
LCD KEYPAD
LED KEYPAD
Press...
[Master Code]
ENTER
Enters Program Mode. The PROGRAM light will be on.
Press...
[Option No.]
ENTER
The two digit option number for the code to be programmed.
The existing code (if any) will be displayed.
Press... [NEW CODE]
ENTER
[NEW CODE]
ENTER
[Master Code]
Enters Program Mode. The PROGRAM light will be on.
Press...
[Option No.]
The two digit option number for the code to be programmed.
The existing code (if any) will be displayed.
Press... [NEW CODE]
[NEW CODE]
Enter the new code twice. The new code will be displayed.
Enter the new code twice. The new code will be displayed.
Press...
To exit Program Mode
ENTER
Press...
Press...
To exit Program Mode
EXAMPLES
The panel must be in Program Mode. (Program light ON)
To program User Code 1 (The Master Code) to be 1234: P11E 1234 E 1234 E
To program User Code 2 as an ARM ONLY code to be 5678: P12E ARM E 5678
E 5678 E
When an Arm Only code is displayed, the ARM light or icon is displayed, followed by the digits of the code
PROGRAMMING TIMERS
LCD KEYPAD
LED KEYPAD
Press...
[Master Code]
ENTER
Enters Program Mode. The PROGRAM light will be on.
Press...
[Option No.*]
ENTER
The existing time will be displayed.
The new time will be displayed.
To exit Program Mode
EXAMPLES
[Option No.*]
Press... [NEW TIME]
Press...
To exit Program Mode
The panel must be in Program Mode. (Program light ON)
To program Entry Delay Time1 to be 15 seconds: P26E 15
To program Exit Delay Time to be 40 seconds: P28E 40 E
18
Press...
The new time will be displayed.
ENTER
Press...
[Master Code]
Enters Program Mode. The PROGRAM light will be on.
The existing time will be displayed.
ENTER
Press... [NEW TIME]
Press...
E
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
PROGRAMMING
PROGRAMMING THE FOLLOW-ME TELEPHONE NUMBER
LCD KEYPAD
LED KEYPAD
Press...
[Master Code]
ENTER
Enters Program Mode. The PROGRAM light will be on.
Press...
[Option No.*]
ENTER
The existing telephone number (if any) will be displayed.
Press... [NEW TELEPHONE NUMBER]
ENTER
The new telephone number will be displayed.
Press...
[Option No.*]
The existing telephone number (if any) will be displayed.
Press... [NEW TELEPHONE NUMBER]
Press...
To exit Program Mode
EXAMPLES
[Master Code]
Enters Program Mode. The PROGRAM light will be on.
The new telephone number will be displayed.
ENTER
Press...
Press...
To exit Program Mode
The panel must be in Program Mode. (Program light ON)
To program the Follow Me Telephone Number to be 9123 1234: P00E
To DELETE the Follow Me Telephone Number: P00E MEMORY E
912341234 E
* For a list of option numbers, see the Programming Options Table on page 17
To enter PROGRAM MODE
[Master Code]
To exit PROGRAM MODE
ENTER
ENTER
[Master Code]
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
19
MONITORING
CENTRAL STATION MONITORING
CENTRAL STATION MONITORING
The ET8 control panel has an on-board digital
dialler which can send detailed alarm messages
to a Central Monitoring Station.
MONITORED PREMISES
TELEPHONE LINE
MONITORING STATION
The digital messages can include information
about the zone or zones which caused the
alarm, tamper alarms, low battery or mains
failure reports, and it can also (by user number)
identify the users who Arm and Disarm the
system.
Central Station Monitoring is highly
recommended and is the most effective method
of monitoring your ET8 alarm system. For
further information about 24 hour monitoring,
contact your installer or E-Tech Security
Products.
20
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
AUDIBLE MONITORING
AUDIBLE MONITORING
FIXED TELEPHONE
MONITORED PREMISES
TELEPHONE LINE
MOBILE TELEPHONE
The ET8 can also be programmed to send
audible messages to any telephone or mobile
phone.
When programmed for audible monitoring, the
ET8 calls a pre-programmed number (or
numbers) and sounds a series of beeps over
the phone. These beeps can identify the zone
or zones which caused the alarm and well as
several other alarm types.
FOLLOW ME TELEPHONE NUMBER
The Follow Me Telephone Number is the
telephone number to which the ET8 sends
alarm reports when Audible Monitoring is
enabled.
The Follow Me Telephone Number can be
changed by the user in User program Mode.
If the Follow Me Telephone Number is
programmed, the Primary and Secondary
telephone numbers are ignored, even if
programmed. (When Audible Monitoring is
enabled).
See page 19 for information on programming
the Follow Me Telephone Number.
AUDIBLE MONITORING SEQUENCE
When triggered by an alarm, the ET8 will dial
the programmed telephone number/s and
output the audible message for 45 seconds or
until it is acknowledged.
ACKNOWLEDGING THE ALARM
* The Primary and Secondary telephone numbers are normally only
used for central station monitoring. These numbers can only be
programmed in Installer Program Mode.
** The Follow Me Telephone Number replaces the Primary AND
Secondary telephone numbers.
The person receiving the call can then
key
acknowledge the alarm by pressing the
on their telephone. Press the
key for at least
2 seconds during pauses in the audible
message.
If the alarm is not acknowledged, the keypad’s
LINE light will flash continuously until the panel
is next Armed.
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
21
REMOTE OPERATION
OPERATING THE ET8 BY TELEPHONE
The ET8 will allow a user to call in to the
panel, using a standard DTMF telephone,
and remotely Arm or Disarm all areas and
also turn on or off Aux 1 and Aux 2.
To ensure security of operation a user can
only carry out remote operations after entering
a valid user code.
WHAT’S NEEDED:
• A telephone with DTMF tones.
• A Valid User code programmed in the
ET8.
• The ET8 to be connected (via Mode 3
socket) to a working telephone line at the
installed premises.
• You need to know the telephone number of
the line that the ET8 is connected to.
SEQUENCE OF OPERATION.
1. Phone the ET8 telephone number and
listen for the required number of rings
(ring ring...ring ring) and then hang up.
2. Wait 10 seconds and then call the number
again within 50 seconds.
3. The ET8 will answer the second call
immediately, sound a beep for 2 seconds
then, after a pause, it will sound a lower
frequency tone. The ET8 is now ready to
receive telephone commands.
button on the telephone. This
4. Press the
tells the ET8 that telephone commands will
follow. It will respond with either 3 beeps if
all OK (One long beep means try again).
5. Now enter a valid User Code (that is
normally used for Arming or Disarming the
ET8) followed by the
button.
The ET8 will respond with 3 beeps if it
recognises the code or 1 long beep to
signal the code was invalid and to try
again.
6. Enter the required command.
See: Summary Of Telephone Commands.
7. Press
to finish. This tells the ET8 to
hang up. Also, hang up your telephone.
NOTES
• If the ET8 does not receive commands for periods longer than 10 seconds it will
assume that the call is finished and it will hang up.
• If an alarm occurs which requires the ET8 to dial out while attempting remote
control, the ET8 will treat the alarm as a priority, give a constant tone as a warning
and then hang up.
• When all remote control commands are finished press
hang up.
22
to force the ET8 to
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
REMOTE OPERATION
EXAMPLE: ARMING THE ET8 BY TELEPHONE
1. Dial the ET8 telephone number. Listen for one double ring then hang up.
2. Wait 10 seconds, then dial the ET8 telephone number again.
The ET8 will answer immediately and gives a 2 second beep followed by low tone.
3. PRESS
To prepare the ET8 (
4. PRESS [User Code]
3 beeps)
to authorise the next command (
5. PRESS
to Arm the panel (
6. PRESS
to finish and hang up
3 beeps)
3 beeps)
AUDIBLE FEEDBACK
3 BEEPS:
• The User Code is valid
• Successful Arming or Disarming
• An Auxiliary output has been turned ON.
1 LONG BEEP:
• ET8 is already Armed
• Invalid code. Try again.
1 SHORT BEEP:
• An Auxiliary output has been turned OFF.
SUMMARY OF TELEPHONE COMMANDS
Prepare to receive commands
Arm Areas
Disarm Areas
Turn Aux 1 Output ON or OFF
Turn Aux 2 Output ON or OFF
Finished – hang up
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
23
E-TECH ACCESSORIES
QUANTUM - 15m passive infra-red detector with
selectable pulse count; suitable for domestic
and commercial installations. PetAware model
available.
100-021
Quantum
100-226
Quantum
Plus
100-210
Quantum
Dual
100-048
Quantum 360
QUANTUM PLUS - 15m passive infra-red
detector with selectable pulse count,
temperature compensation and downward
looking ‘creep’ zones.
MOTION DETECTORS
E-Tech manufactures a range of high quality
and efficient motion detectors - including
passive infra-red detectors, dual technology /
microwave and infra-red devices as well as
ceiling mounted 360° detectors.
QUANTUM DUAL - 15m combination microwave
and passive infra-red detector. This combination
of detection technologies virtually eliminates the
possibility of unwanted alarms but faithfully
detects humans. PetAware model available.
All E-Tech detectors are designed using the
most modern technology and techniques that
ensure superior reliability and performance.
QUANTUM 360 - Ceiling mounted 360° passive
infra-red detector with selectable pulse count
and sensitivity. Provides 8 metre coverage
mounted at standard 2.4 metre ceiling height.
PET AWARE DETECTORS
The E-Tech Quantum™ Pet Aware PIR and Pet
Aware DUAL are able to discriminate between
household pets and
unwanted
human
intruders, allowing you
to secure your home
with your pets indoors.
CCTV
The E-Tech range of Closed Circuit TV
equipment includes Dome cameras, B/W or
Colour cameras, Miniature hidden cameras,
Monitors - even digital video recorders and
remote telephone video systems.
24
SIRENS
The range of warning devices includes horn
speakers, polytough siren covers, internal
‘screamers’ and satellite sirens with their own
battery backup.
SWITCHES
A variety of switches are available for protecting
doors and windows. The line-up includes
surface and flush mount reed switches,
emergency buttons, roller door reed switches
and the unique E-Techensor™ vibration sensor
for highly effective perimeter protection.
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
WIRELESS PRODUCTS
RADIO ACCESSORIES
Ask your installer about the range of E-Tech
radio devices for the optional extra
convenience of wireless remote control and
wireless detection.
Operating your E-Tech
security system can be as
convenient as opening your
car door. The E-Tech Radio Key™ provides
the benefits of separate ON, OFF and PANIC
buttons in a slim, waterproof remote control.
* E-Tech radio products require a E-Tech Radio
Interface (100-200) to be fitted to the control
panel.
E-TECH RADIO KEYPAD
A unique fully portable radio
keypad. The E-Tech Radio
Keypad provides totally
wireless Arming/Disarming of
the E-Tech ET8, ET16 & D24
control panels.
Also operates Monitor mode and Panic when
used with the E-Tech ET16, D24 panels.
The E-Tech radio Keypad is suitable for use as
a portable keypad or for adding an extra
keypad in areas where it is not possible to
install wires.
E-TECH RADIO PIR
E-Tech Radio PIR (Passive
Infrared) motion detector for
wireless motion detection.
Can be used in combination
with E-Tech hardwired detectors
in areas where it is not possible
to install wires. Includes long life
E-TECH RADIO KEY PENDANT
Fully waterproof pendant style
transmitter can be used as a
portable wireless Panic button.
Supplied with a neckchain as well
as wristwatch straps. Ideal for use
as a medical alarm for the elderly
or infirm. (Central Station Monitoring is
especially recommended when used for medical
alarm purposes). Includes long life lithium battery.
E-TECH RADIO REED SWITCH
E-Tech Radio Reed Switch for
wireless door and window
protection. Includes long life
lithium battery.
E-TECH RADIO KEY 3 BUTTON
Fully waterproof, ultra slim 3
button Radio Key for remote
control of the control panel.
With separate buttons for ON
(Arm), OFF (Disarm) and PANIC functions.
Includes long life lithium battery.
E-TECH RADIO SMOKE DETECTOR
Radio Smoke Detector using Ionisation smoke
detection technology. With on board sounder.
A single battery powers the
smoke detector and the
transmitter. Includes 9V
lithium battery.
lithium battery.
Also available, the 100-663PET radio Pet Aware
model, which detects humans but is immune to
household pets.
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
25
TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
REMEDY
Zone light on or long beeps when
Arming
One or more Zone Detection Devices
(e.g., PIR, Reed Switch) may be
Unsealed
Close door or window, find the cause
of movement
10 beeps from keypad
MAINS light flashing
BATTERY light flashing
Make sure the plug pack is plugged in
The mains power may be off,
...or the panel’s backup battery may be low, and the power point is turned on.
...or a Radio Device battery may be low. Call your installer.
1 long beep from keypad
Invalid keypad entry
Press E button and try again
2 second siren at the end of Exit
Delay time
A zone was Unsealed at the end of Exit
Delay time
Disarm the panel and check all zones
Strobe light is flashing
There has been an alarm
Reset the alarm by Disarming the
panel and check the Alarm Memory
Siren sounds while the panel is
Disarmed
A 24 hour zone has been triggered.
E.g, Siren Tamper, Box Tamper, Panic
Button.
Reset the alarm by Disarming the
panel and call your installer.
EXCLUDE light is flashing
A zone/s has been Excluded
TAMPER light flashing
The 24 hour Tamper input has
triggered
Call your installer
ALARM MEMORY light is flashing
There are alarms in memory
To clear the ALARM MEMORY light,
view the Alarm memory otherwise the
light will clear next time you Arm the
panel.
Cannot enter Program Mode
The panel is Armed.
Only the Master Code can enter
Program Mode.
Disarm the panel before attempting to
enter Program Mode.
Try again using the Master Code.
26
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
INSTALLATION RECORD
INSTALLATION RECORD
Date purchased:
Date installed:
Installation Company:
Telephone:
E-TECH ET8
ALARM CONTROL PANEL
Monitoring Company:
ZONES
DEVICE TYPE
PIR, Reed
switch, etc
DESCRIPTION
P74E Report (dialler)
P57E SIREN OUTPUT
P56E SONALERT OUTPUT
P54E RESET OUTPUT
P52E 24 HOUR
P51E MONITOR
Minutes
P46E AREA 2
P29E SIREN RESET TIME
P45E AREA 1
Seconds
P40E INSTANT
Seconds
P28E EXIT DELAY TIME
P42E HANDOVER
P27E ENTRY DELAY TIME 2
ZONE ASSIGNMENT
P43E ENTRY DELAY 2
Seconds
P41E ENTRY DELAY 1
P26E ENTRY DELAY TIME 1
P55E STROBE OUTPUT
Telephone:
Entrance, bedroom1, etc
1
2
3
4
5
6
7
8
OPTION No
CODE
User Code 1
Master
Code
CODE HOLDER
P11E
User Code 2
P12E
User Code 3
P13E
User Code 4
P14E
User Code 5
P15E
User Code 6
P16E
User Code 7
P17E
User Code 8
P18E
User Code 9
P19E
User Code 10
P20E
User Code 11
P21E
User Code 12
P22E
User Code 13
P23E
User Code 14
P24E
User Code 15
P25E
AREA 1
AREA 2
RADIO KEY
CODE (Y/N)
(Keypad Code only)
© 2001 E-Tech Security Products
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
27
OPERATION SUMMARY
OPERATION
or...
[User Code]
ARM
[User Code]
DISARM
ENTER
[User Code]
x2
[User Code]
PANIC
or...
PANIC
or...
PANIC
PANIC
ENTER
or...
[User Code]
Press twice within 4 seconds
P69E 5E must be ON
Both keys together
[User Code]
ENTER
(Keypad Panic Shortcut
must be ON, P62E 4E)
ENTER
[x] [User Code]
KEYPAD DURESS
[User Code]
ENTER
MONITOR
MONITOR
or...
ENTER
MONITOR MODE
or...
Both keys together
or...
[User Code]
(Keypad Panic Shortcut
must be ON, P62E 4E)
or...
[x] [User Code]
ENTER
To Disarm and report a Duress Alarm, add any of the digits 5, 6, 8 or 9 before the User Code when Disarming
ENTER
EXCLUDE
EXCLUDING ZONES
or...
[User Code]
EXCLUDE
[Zone No.]
[Zone No.]
ENTER
ENTER
ENTER
MEMORY
ALARM MEMORY
or...
Press
MEMORY
MEMORY
ENTER
28
RADIO KEY
ENTER
ARM
ARM
PANIC
LCD KEYPAD
LED KEYPAD
ENTER
or...
Enter the zone numbers
to be Excluded
[Zone No.]
[Zone No.]
[User Code]
Enter the zone numbers
to be Excluded
To exit Exclude mode
To exit Exclude mode
ENTER
[User Code]
ENTER
repeatedly to display the last
30 events
To exit Memory mode
or...
Press
[User Code]
repeatedly to display
the last 30 events
To exit Memory mode
E-TECH ET8 V4 CONTROL PANEL - USER MANUAL
Hold
Press and hold for 4 seconds
(P68E 3E & 4E must be OFF)
Download PDF