+Bona Specification Binder

+Bona Specification Binder
Specification Binder - Table of Contents
PAGES
PRODUCT
Filler
2,3
4,5
6,7
8,9
10,11
12,13
14,15
16,17
18,19
20,21
22,23
24,25
26
27,28
29
30,31
32,33
34,35
36,37
38,39
40
41,42
43
44,45
46,47
48,49
50,51
52,53
54,55
56,57
58,59
60,61
62,63
64,65
66,67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100,101
102,103
104,105
106,107
Pacific Filler
Stain
DriFast Quick Dry Stain
Waterborne Sealer & Finish Systems
Bonaseal
Bona DTS
Bona AmberSeal
Bona Naturale
Bona Indoor Wood Oil
Bona Traffic HD
Bona Traffic Anti-Slip Satin
Bona Traffic
Bona Mega Clear HD
Bona Mega
Bona Mega Booster
Bona Novia
Bona Retarder
Oil-Modified Sealer & Finish Systems
Bona DriFast Quick Dry Sealer
Woodline Polyurethane
Woodline Polyurethane 350
Recoating Systems
Bona Prep
Bona Remover
Bona Rinse
Bona Deep Clean Polish
Sport Floor Systems
Bona Professional Series Sport & Commercial Cleaner Concentrate
Bona Sportive Finish
Bona Sportive 1K Finish
Bona Sport SuperSport Seal
Bona Sport SuperSport
Bona Sport SuperSport One Finish
Bona Sport Sport Seal
Bona Sport DriFast Sport Seal
Bona Sport All Court Polyurethane
Bona Sport Sport Poly
Bona Sport Sport Seal 350
Bona Sport Sport Poly 350
Bona Sport Courtlines Paint
Floor Care
Bona Deep Clean Solution
Bona Pro Series Hardwood Floor Cleaner
Bona Pro Series Hardwood Floor Cleaner Concentrate
Bona Pro Series Hardwood Refill Cartridge
Bona Pro Series Hardwood Floor Refresher
Bona Pro Series Hardwood Floor Mop
Bona Pro Series 18" Hardwood Floor Care Kit
Bona Pro Series 15" Hardwood Floor Care System
Bona Pro Series Natural Oil Floor Cleaner
Bona Pro Series Natural Oil Floor Cleaner System
Bona Pro Series Stone, Tile & Laminate Floor Cleaner
Bona Pro Series Stone, Tile & Laminate Refill Cartridge
Bona Pro Series Stone, Tile & Laminate Floor Refresher
Bona Pro Series Microfiber Pads
Sanding Equipment
Bona Atomic 300 DCS
Bona Atomic 600 DCS
Bona Portable DCS
Bona Power Station Plus
Bona Belt
Bona Edge XL
Bona Edge
Bona Mini Edge
Bona FlexiSand DCS Buffer
Bona DCS Super Vac
Bona DCS Back Vac
Abrasives
Bona BLUE Anti-Static Abrasives
Bona BLUE Edger Discs
Siafast Edger Discs
Bona Double Sided Sanding Discs
Screens
Bona Conditioning Pad
Siafast Delta Sheet
Adhesives
Bona R848
Bona R580
Bona R851
Bona R850T
Bona Pacific Filler™
Finishing
Technical data sheet
A waterborne compound specifically designed for filling cracks, holes, chips, gouges and broken
edges in hardwood floors prior to finishing. Pacific Filler’s high solid content formula is ready to
use, trowelable direct from pail, or can be thinned with water for trowel filling.
Ready to use – easy to spread for trowel filling
Ideal for spot filling
May be thinned with water
Safe to use, nonflammable
Sands easily
Fills the soft grain
Helps minimize grain raise
Available in six wood tones: Red Oak, White Oak, Ash-Maple-Pine, Brazilian Cherry, American
Cherry, and Walnut
Accepts stain like wood
Can be tinted with Universal Color tints to match custom or exotic woods
Dries with minimum shrinkage
Excellent adhesion, bonds tightly to wood
Tools can be cleaned with water before compound dries
Technical data
Physical Characteristics:
Ingredients – Inorganic fillers, water, binders, pigments
Colors – Red Oak, White Oak, Ash-Maple-Pine, Brazilian Cherry, American Cherry, Walnut
Odor – Mild latex odor
Solids – 65-75%
Density – 13.3 lbs/gallon (1.60 S.G)
US Regulatory VOC –250 g/L
Stability – 1 year shelf life in unopened container
Application Characteristics:
Drying Time – 30 minutes to 2 hours, depending on environmental conditions (temperature and
humidity), coverage rate, and size of cracks and holes.
Coverage – 600-800 square feet per gallon
®
Application Tools – Putty knife, Bona Trowel
Packaging – Quart plastic container: Red Oak, White Oak, Ash-Maple-Pine, Brazilian Cherry,
American Cherry, Walnut
1 Gallon plastic container: Red Oak, White Oak, Ash-Maple-Pine, Brazilian Cherry, American
Cherry, Walnut
3-1/2 Gallon plastic container: Ash-Maple-Pine, Red Oak, White Oak
Recommended Use
Apply over bare wood before final sanding cut
®
®
®
®
Formulated for use with Bona Drifast Stain, all Bona waterborne and all other Bona finishing
systems.
Always prepare a test sample on a small area to determine compatibility and color acceptance
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
COMPATIBILITY: Bona Pacific Filler will accept most stains, sealers and finishes in the same
manner as most woods. ALWAYS PREPARE A TEST OR SAMPLE AREA TO DETERMINE
COMPATIBILITY. Do not use wood bleach over Bona Pacific Filler as it may damage the filler.
SANDING AND FINISHING NEW FLOORS: Sand and prepare floor using accepted industry
association methods.
THE PACIFIC FILLER SYSTEM: Bona Pacific Filler™ brand hardwood floor filler is a high solids
content, waterborne compound specifically designed for filling cracks, holes, chips, gouges and
broken edges in hardwood floors prior to finishing. This product has excellent adhesion, staining
and finishing properties with minimum shrinkage.
RECOMMENDED APPLICATORS: Stainless steal trowel, Putty knife
Rev 11/10
This data sheet replaces all previous versions
page 1/2
Bona Pacific Filler™
Finishing
Technical data sheet
MIXING INSTRUCTIONS: Stir thoroughly before using. One to two cups of water may be added
per gallon.
FILLING: Apply Bona Pacific Filler 600-800 sq. ft. per gallon before final sanding with the drum or
belt machine. Thoroughly vacuum dust from cracks and holes before filling. Work the filler as deep
as possible into cavities. To fill and level larger holes or deeper cracks, several applications may be
required. It may be necessary to trowel-fill the entire floor, depending upon the extent of cracks
between strip or parquet floors. Allow sufficient drying time: 30 minutes to 2 hours before final
sanding. Higher humidity or cooler conditions will increase the drying time.
Bona Pacific Filler is tintable with Universal Color tints. Do not exceed more than 1 ounce of tint per
gallon of filler. Use the Bona Pacific Filler that is closest in color to the floor being finished.
Maintenance
CLEAN UP: Clean tools with water
STORAGE AND DISPOSAL: Store at room temperature. Keep container closed when not in use.
Do not store above 100° F (38° C).
Order Information
Item#
AF0001822
AF0001823
AF0001826
AF0001827
AF0001829
AF0001831
AF0001539
AF0001824
AF0001537
AF0001828
AF0001830
AF0001832
AF0001821
AF0001825
AF0001820
Size/Color
Quart – Red Oak
Quart – White Oak
Quart – Ash/Maple/Pine
Quart – Brazilian Cherry
Quart – American Cherry
Quart – Walnut
Gallon – Red Oak
Gallon – White Oak
Gallon – Ash/Maple/Pine
Gallon – Brazilian Cherry
Gallon – American Cherry
Gallon – Walnut
3.5 Gallon – Red Oak
3.5 Gallon – White Oak
3.5 Gallon – Ash/Maple/Pine
Rev 11/10
This data sheet replaces all previous versions
#/Case
8
8
8
8
8
8
2
2
2
2
2
2
1
1
1
page 2/2
®
DriFast Stain
Finishing
Technical data sheet
An oil-modified stain that dries and is recoatable in two hours. A premium quality quick-drying stain
®
for interior hardwood floors, DriFast Stain’s advanced technology formula provides speed and
®
high performance for hardwood floor finishing professionals. Compatabile with all Bona
®
waterborne systems and all other Bona finish systems.
2 hour dry time*
No bleed back
Penetrates, stains, and seals bare wood
800-1,000 sf/gal coverage rate
Available in 14 wood tones and white
All stain colors can be blended, offering an endless color palette
Clean up with mineral spirits
Low odor
Easy touch-ups (mineral spirits for thinning dark or heavy spots)
*6 hours for white under ideal conditions (60-80ºF, 35-75% relative humidity).
Technical data
Physical Characteristics:
Ingredients – Wood tones: Oil-modified resins, mineral spirits (solvent), pigments, driers
White: Oil-modified resins, mineral spirits (solvent), Titanium Dioxide, fillers
Colors – Wood tones: Natural, Golden Oak, Nutmeg, Early American, Provincial, Special Walnut,
Rosewood, Red Mahogany, Jacobean, Ebony, Medium Brown, Antique Brown, Puritan pine,
Cherry.
Pastel: White (Not recommended on white oak due to excessive color variation).
Solids – 35-40%
Density – Wood tones: 7.2-7.5 lbs/gallon (0.86-0.90 s.g.), White: 8.7-9.0 lbs/gallon (1.04-1.8 s.g.)
US Regulatory VOC –550 g/L
Odor – Mild solvent odor
Stability – One year shelf life in unopened container
Flashpoint – 103ºF (39ºC)
Packaging – 1-quart cans · 1-gallon cans
Application Characteristics:
Clarity – Semi-transparent (dry)
Drying Time – 2 hours for wood tones, 6 hours minimum for White, under ideal conditions (60-80º
F, 35-75% relative humidity).
Coverage – 800-1,000 square feet per gallon
Application Tools – Clean cloths, brush, cut-in pad
Recommended Use
Apply only over bare wood
®
®
Prepares the surface for a topcoat of Bona waterborne or any other Bona finish
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
COMPATIBILITY: Bona does not recommend using white stain on white oak due to excessive
color variation. Stain, sealer and finish results may vary widely depending on the wood species,
especially on oily and resinous Exotics. ALWAYS PREPARE A SAMPLE OR TEST AREA TO
DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using accepted
industry association methods. 2. Make your final cut with 80-100 grit paper and screen to 80-100
®
grit. 3. Use a Tampico Brush on a buffer and vacuum thoroughly. 4. Tack with a dry Bona
Microfiber Mop or cloth to remove dust. 5. Apply stain system.
®
®
THE BONA DRIFAST STAIN SYSTEM: Bona DriFast Stain is a redesolving stain designed to
penetrate, stain and seal bare wood. Bona DriFast Stain is designed to work with all Bona finishes.
Colors may be blended with all other Bona DriFast Stains. Visit www.bona.com for additional
product information.
Rev 05/11
This data sheet replaces all previous versions
page 1/2
®
DriFast Stain
Finishing
Technical data sheet
RECOMMENDED APPLICATORS & TOOLS: Brush, cut-in pad, cloth, carpet disc
MIXING INSTRUCTIONS: Shake or stir well before using. Do not thin.
STAINING: 1. After preparing surface, apply Bona DriFast Stain with brush, cut-in pad, cloth or
carpet disc driven by a buffer in the direction of the grain at the coverage rate of 800 – 1000 square
feet per gallon. 2. Allow 1-3 minutes for penetration. Remove excess by hand wiping or buffing with
an absorbent, non-abrasive material. 3. Allow stain to dry thoroughly (minimum 2 hours for wood
tones; 6 hours for white under ideal conditions of 60-80°F (16°-27° C), 35-75% relative humidity).
High humidity and/or low temperature conditions will extend dry time, while increased ventilation
and airflow will reduce dry time. Apply sealer or finish after the recommended dry
time, but within 48 hours after application. 4. Apply any Bona finish system over thoroughly dried
stain.
STORAGE AND DISPOSAL: Store at room temperature. Keep container closed when not in use.
Do not store above 100° F (38° C). Do not transfer contents to other containers for storage and
disposal. In case of spillage, absorb with inert material. Dispose of contaminated absorbent,
container and unused contents in accordance with local, state and federal regulations.
DANGER: RAGS, STEEL WOOL OR WASTE SOAKED WITH BONA DRIFAST STAIN MAY
SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED. IMMEDIATELY AFTER EACH
USE, PLACE RAGS, STEEL WOOL OR WASTE IN A SEALED, WATER-FILLED, METAL
CONTAINER.
Maintenance
CLEAN-UP: Clean application tools and equipment with mineral spirits.
STORAGE AND DISPOSAL: Store at room temperature. Keep container closed when not in use.
Do not store above 100ºF (38ºC). Do not transfer contents to other containers for storage and
disposal. In case of spillage, absorb with inert material. Dispose of contaminated absorbent,
container and unused contents in accordance with local, state and federal regulations.
Order Information
Item #
SS750051100
SS750051101
SS750051102
SS750051103
SS750051104
SS750051105
SS750051106
SS750051107
SS750051108
SS750051109
SS750051110
SS750051111
SS750051112
SS750051113
SS750051114
SS750018100
SS750018101
SS750018102
SS750018103
SS750018104
SS750018105
SS750018106
SS750018107
SS750018108
SS750018109
SS750018110
SS750018111
SS750018112
SS750018113
SS750018114
Size / Color
Quart - Natural
Quart - Nutmeg
Quart - Golden Oak
Quart - Early American
Quart - Provincial
Quart - Special Walnut
Quart - Rosewood
Quart - Red Mahogany
Quart – Jacobean
Quart – Ebony
Quart – White
Quart – Medium Brown
Quart – Antique Brown
Quart – Puritan Pine
Quart – Cherry
Gallon – Natural
Gallon – Nutmeg
Gallon – Golden Oak
Gallon – Early American
Gallon – Provincial
Gallon – Special Walnut
Gallon – Rosewood
Gallon – Red Mahogany
Gallon – Jacobean
Gallon – Ebony
Gallon – White
Gallon – Medium Brown
Gallon – Antique Brown
Gallon – Puritan Pine
Gallon – Cherry
Rev 05/11
This data sheet replaces all previous versions
#/Case
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
page 2/2
®
Bonaseal
Finishing
Technical data sheet
®
®
®
Bonaseal wood floor sealer is specially formulated for use with Bona Naturale , Bona Traffic ,
®
®
Bona Mega , and Bona Strong™ finishes. Bonaseal seals the wood, minimizes grain raise,
provides a build layer, and prevents the finish from penetrating into the wood surface.
Seals the wood, preventing the finish from penetrating
Minimizes tannin bleed, especially on white oak
Reduces tendency for sidebonding
Improves flow and leveling of finish coats
Non-yellowing
Fast drying – 2-3 hours
Virtually odorless
Water clean-up
GREENGUARD certified for indoor air quality
Technical data
Physical Characteristics:
Ingredients – Water, acrylic resin, dipropylene glycol monomethyl ether, defoamers.
Color – Milky white (wet)
pH – 7.8
Solids – 36%
Density – 8.70 lbs/gallon (1.04 S.G.)
US Regulatory VOC – 100 g/L
Gloss Level – N/A
Odor – Non-offending
Packaging – 1-gallon plastic bottle
Application Characteristics:
Clarity – Clear when dry
Leveling – Excellent
Defoaming – Excellent
Drying Time – approximately 2-3 hours (high humidity and/or low temperature conditions will
extend the drying time)
Coverage – 500-600 square feet per gallon
Percent Cured After 24 Hours – N/A
Maximum Cure – 100% after 1 week
Recommended Use
Residential wood floors
Commercial wood floors
For use on newly sanded wood floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
COMPATIBILITY: Stain, sealer and finish results may vary widely depending on the wood species,
especially on oily and resinous Exotics. ALWAYS PREPARE A SAMPLE OR TEST AREA TO
DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using accepted
industry association methods. 2. For a stained floor, make your final cut with 80-100 grit paper
and screen to 80-100 grit. For an unstained floor, make your final cut with 80-100 grit paper and
disc/screen to 120-150 grit. This burnishing will reduce the amount of grain raise. 3. Use a
®
Tampico Brush on a buffer and vacuum thoroughly. 4. Tack with a dry Bona Microfiber Mop or
cloth to remove dust. 5. Apply finish system.
®
THE BONASEAL SYSTEM: Apply 1 coat of Bonaseal and 2 coats of a Bona waterborne finish.
Bonaseal is not recommended over Bona stain. Bonaseal minimizes side-bonding and grain raise,
provides a build layer, and prevents the finish from penetrating into the wood surface. Visit
www.bona.com for additional product information.
®
®
®
RECOMMENDED APPLICATORS: Bona Floor Coater (T-bar), Bona Roller, Bona Cut-In Pad.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
Rev 11/10
This data sheet replaces all previous versions
page 1/2
®
Bonaseal
Finishing
Technical data sheet
MIXING INSTRUCTIONS: SHAKE WELL BEFORE USING – DO NOT THIN. DO NOT ADD
WATER. Insert supplied filter.
SEALING: 1. Pour a 4” wide line of sealer along the starting wall. Go with the grain of the wood.
2. Using a pre-dampened T-bar sleeve, draw the applicator forward with the grain of the wood,
moving the sealer toward the opposite wall. To maintain a wet edge at all times, hold the applicator
at a snowplow angle. 3. At the end of each run, turn the applicator towards you and pad out the
applicator parallel to the wet edge. 4. Feather out all turns. Do not push too hard or too fast to
avoid drips flying off the applicator. 5. BE SURE YOU ARE USING THE RECOMMENDED
COVERAGE OF 500-600 SQ. FT. PER GALLON. DO NOT SPREAD TOO THIN. 6. Allow the first
coat to dry 2-3 hours. High humidity and/or low temperature conditions will extend the dry time
(recommended conditions of 65-80° F (18°C-27°C) 40-60% relative humidity). 7. For smoothest
results, abrade before applying finish coats. Always vacuum and tack thoroughly with a slightly
water dampened Bona Microfiber Mop or cloth after abrading.
INTERCOAT ABRASION: It is not necessary to abrade Bonaseal unless more than 48 hours has
passed since the previous coat was applied. However, for smoothest results, abrade Bonaseal with
a Bona Conditioning Pad and 1-2 Delta sheets as needed. Always vacuum and tack thoroughly
with a slightly water-dampened Bona Microfiber Mop or cloth after abrading.
Maintenance
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container.
This product has a maximum VOC (Volatile Organic Compound) content of 100 grams per
STORAGE: Nonflammable - Bonaseal should be stored in a climate controlled environment. KEEP
FROM FREEZING. Do not store above 100° F (38° C).
Order Information
Item #: WB200018005
Size: 1 Gallon
#/Case: 3
Rev 11/10
This data sheet replaces all previous versions
page 2/2
®
Bona DTS
Finishing
Technical data sheet
®
Bona DTS Deep Tone Sealer is a specially formulated waterborne sanding sealer for use with all
®
Bona waterborne finishes. Bona DTS seals the wood, develops a vibrant look and deep, natural
tone. It abrades easily and prevents the finish from penetrating into the wood surface.
Unique “wet look” appearance adapts to the individual wood species, accentuating the natural
pigmentation and color characteristics
Excellent sandability – hardens rapidly and allows for easy abrasion
Seals the wood, preventing the finish from penetrating
Reduces tendency for sidebonding
Exceptional flow and leveling of finish top coats
Fast drying – 2-3 hours
GREENGUARD certified for indoor air quality
Nonflammable
Water clean-up
Product can be rolled or pulled with a t-bar
Technical data
Physical Characteristics:
Ingredients – Water, polymeric resin, silica derivate, diethylene glycol monoethyl ether, and
polysiloxane.
Color – Milky white (wet)
pH – 7.5 - 7.9
Solids – 31-32%
Density – 8.66 lbs/gallon (1.04 S.G.)
US Regulatory VOC – 250 g/L
Odor – Non-offending
Packaging – 1-gallon plastic bottle
Application Characteristics:
Clarity – Clear when dry
Leveling – Excellent
Defoaming – Excellent
Drying Time – approximately 2-3 hours (high humidity and/or low temperature conditions will
extend the drying time)
Coverage – 450-600 square feet per gallon
Percent Cured After 24 Hours – N/A
Maximum Cure – 100% after 1 week
Recommended Use
Residential wood floors
Commercial wood floors
For use on newly sanded wood floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
COMPATIBILITY: Stain, sealer and finish results may vary widely depending on the wood species,
especially on oily and resinous Exotics. ALWAYS PREPARE A SAMPLE OR TEST AREA TO
DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using accepted
industry association methods. 2. For a stained floor, make your final cut with 80-100 grit paper
and screen to 80-100 grit. For an unstained floor, make your final cut with 80-100 grit paper and
disc/screen to 120-150 grit. This burnishing will reduce the amount of grain raise. 3. Use a
®
Tampico Brush on a buffer and vacuum thoroughly. 4. Tack with a dry Bona Microfiber Mop or
cloth to remove dust. 5. Apply finish system.
®
THE BONA DTS SYSTEM: Apply 1-2 coats of Bona DTS and 2 coats of a Bona waterborne
finish. Bona DTS is not needed when using a Bona stain with a Bona waterborne finish. Bona DTS
minimizes side-bonding and grain raise, provides a build layer and prevents the finish from
penetrating into the wood surface. Visit www.bona.com for additional product information.
Rev 11/10
This data sheet replaces all previous versions
page 1/2
®
Bona DTS
Finishing
Technical data sheet
®
®
®
RECOMMENDED APPLICATORS: Bona Floor Coater (T-bar), Bona Roller, Bona Cut-In Pad.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: SHAKE WELL BEFORE USING – DO NOT THIN. DO NOT ADD
WATER. Insert supplied filter.
SEALING: 1. Pour a 4” wide line of sealer along the starting wall. Go with the grain of the wood.
2. Using a pre-dampened T-bar sleeve, draw the applicator forward with the grain of the wood,
moving the sealer toward the opposite wall. To maintain a wet edge at all times, hold the applicator
at a snowplow angle. 3. At the end of each run, turn the applicator towards you and pad out the
applicator parallel to the wet edge. 4. Feather out all turns. Do not push too hard or too fast to
avoid drips flying off the applicator. 5. BE SURE YOU ARE USING THE RECOMMENDED
COVERAGE OF 450-600 SQ. FT. PER GALLON. DO NOT SPREAD TOO THIN. 6. Allow the first
coat to dry 2-3 hours. High humidity and/or low temperature conditions will extend the dry time
(recommended conditions of 65-80° F (18°C-27°C) 40-60% relative humidity). 7. For smoothest
results, abrade before applying finish coats. Always vacuum and tack thoroughly with a slightly
water dampened Bona Microfiber Mop or cloth after abrading.
INTERCOAT ABRASION: It is not necessary to abrade DTS unless more than 48 hours has
passed since the previous coat was applied. However, for smoothest results, abrade the DTS
sealer coat with a Bona Conditioning Pad and 1-2 Delta sheets as needed or a 150 grit or finer
screen. Always vacuum and tack thoroughly with a slightly water-dampened Bona Microfiber Mop
or cloth after abrading.
Maintenance
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container.
STORAGE: Nonflammable – Bona DTS should be stored in a climate-controlled environment.
KEEP FROM FREEZING. Do not store above 100º F.
Order Information
Item #: WB252018001
Size: 1 Gallon
#/Case: 3
Rev 11/10
This data sheet replaces all previous versions
page 2/2
™
Bona AmberSeal
Finishing
Technical data sheet
Bona AmberSeal is a poly-toned, waterborne sanding sealer specially formulated for use with all
Bona waterborne finishes. Bona AmberSeal combines the color and depth of oil-based products
with the low VOC’s and safety of waterborne sealers. It has excellent abradability, fast dry times
and reduces the potential for sidebonding and tannin bleed. Bona AmberSeal is a nonflammable,
virtually odorless sealer, and is GREENGUARD certified for indoor air quality.
Amber color provides a warm, rich oil-based look
Excellent abradability – hardens rapidly and allows for easy abrasion with screens or
conditioning pads
Seals the wood, preventing the finish from penetrating for maximum build and depth
Reduces tendency for sidebonding
Exceptional flow and leveling of finish top coats
Fast drying – 2-3 hours
GREENGUARD certified for indoor air quality
Nonflammable
Water clean-up
Product can be applied with a t-bar or roller
Technical data
Physical Characteristics:
Ingredients: Water, polymeric resin, silica derivate, diethylene glycol monoethyl ether, and
propylene glycol.
Color – Amber (wet)
pH – 7.3 - 7.7
Solids – 30-31.5%
Density – 8.68 lbs./gallon (1.04 S.G.)
US Regulatory VOC – 250 g/L
Odor – Non-offending
Packaging – 1 gallon plastic bottle
Application Characteristics:
Clarity – Clear when dry
Leveling – Excellent
Defoaming – Excellent
Drying Time – approximately 2-3 hours (high humidity and/or low temperature conditions will
extend the drying time)
Coverage – 400-500 square feet per gallon
Percent Cured After 24 Hours – N/A
Maximum Cure – 100% after 1 week
Recommended Use
Apply 1-2 coats over bare wood for increased tone, vibrancy, and depth of color
Residential wood floors
Commercial wood floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
COMPATIBILITY: Stain, sealer and finish results may vary widely depending on the wood species,
especially on oily and resinous Exotics. ALWAYS PREPARE A SAMPLE OR TEST AREA TO
DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using accepted
industry association methods. 2. For a stained floor, make your final cut with 80-100 grit paper and
screen to 80-100 grit. For an unstained floor, make your final cut with 80-100 grit paper and
disc/screen to 120-150 grit. This burnishing will reduce the amount of grain raise. 3. Use a Tampico
®
Brush on a buffer and vacuum thoroughly. 4. Tack with a dry Bona Microfiber Mop or cloth to
remove dust. 5. Apply finish system.
THE BONA AMBERSEAL™ SYSTEM: Apply 1-2 coats of Bona AmberSeal and 2 coats of a Bona
waterborne finish. Bona AmberSeal is not needed when using a Bona stain with a Bona
waterborne finish. Bona AmberSeal minimizes side-bonding and grain raise, provides a build layer
Rev 11/10
This data sheet replaces all previous versions
page 1/2
™
Bona AmberSeal
Finishing
Technical data sheet
and prevents the finish from penetrating into the wood surface. Visit www.bona.com for additional
product information.
®
®
®
RECOMMENDED APPLICATORS: Bona Floor Coater (T-bar), Bona Roller, Bona Cut-In Pad.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: SHAKE WELL BEFORE USING – DO NOT THIN. DO NOT ADD
WATER. Insert supplied filter.
SEALING: 1. Pour a 4” wide line of sealer along the starting wall. Go with the grain of the wood.
2. Using a pre-dampened T-bar sleeve, draw the applicator forward with the grain of the wood,
moving the sealer toward the opposite wall. To maintain a wet edge at all times, hold the applicator
at a snowplow angle. 3. At the end of each run, turn the applicator towards you and pad out the
applicator parallel to the wet edge. 4. Feather out all turns. Do not push too hard or too fast to
avoid drips flying off the applicator. 5. BE SURE YOU ARE USING THE RECOMMENDED
COVERAGE OF 400-500 SQ. FT. PER GALLON. Uneven coverage can cause blotchiness, or
color variance. Certain species may require a second coat to achieve desired appearance. 6. Allow
each coat to dry 2-3 hours. High humidity and/or low temperature conditions will extend the dry
time (recommended conditions of 65-80° F (18°C-27°C) 40-60% relative humidity). 7. For
smoothest results, abrade before applying finish coats. Always vacuum and tack thoroughly with a
slightly water dampened Bona Microfiber Mop or cloth after abrading.
INTERCOAT ABRASION: It is not necessary to abrade AmberSeal unless more than 48 hours has
passed since the previous coat was applied. However, for smoothest results, abrade Bona
®
AmberSeal with a Bona Conditioning Pad and 1-2 Delta sheets as needed or a 150 grit or finer
screen. Always vacuum and tack thoroughly with a slightly water-dampened Bona Microfiber Mop
or cloth after abrading.
Maintenance
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container.
This product has a maximum VOC (Volatile Organic Compound) content of 250 grams per
STORAGE: Nonflammable - Bona AmberSeal should be stored in a climate-controlled
environment. KEEP FROM FREEZING. Do not store above 100° F (38° C).
Order Information
Item #: WB252018003
Size: 1 Gallon
#/Case: 3
Rev 11/10
This data sheet replaces all previous versions
page 2/2
®
Bona Naturale
Finishing
Technical data sheet
Bona Naturale® is the next generation of wood floor protection that preserves the true, natural look of
your hardwood floor. With Bona Naturale, you get as close to an untreated look and feel as possible while
still providing your floor with a durable surface.
Along with Bona Naturale’s elegant look and noticeably unique feeling underfoot, this finish also has
superb durability.
For trained, experienced professionals only.
Preserves the true nature of any wood floor, staying as close to an untreated look as possible.
Phenomenal “haptic” properties, giving wood floors a warm and comforting feel underfoot.
Durability equivalent to Bona Traffic®, the best in the industry.
Seamless “touch up” on repairs. Extremely forgiving product.
Classified by Underwriters Laboratories Inc. as to slip resistance only, Control #21KM.
GREENGUARD certified for indoor air quality.
Technical data
Physical Characteristics:
Ingredients – Water, polymeric resin, dipropylene glycol monomethyl ether, silica derivate, and
amorphous silica
Color – Milky white (wet)
pH – 8.1
Solids – 33% (with hardener)
Density – 8.66 lbs/gallon (1.04 S.G.)
US Regulatory VOC Compliant – 210 g/L
Coefficient of Friction = 0.7
Gloss Level – (60°) – 4-6 for Commercial Matte
(85°) – 4-7 for Commercial Matte
Odor – Non-offending
Stability – 1 year shelf life in unopened container
Packaging – 1-gallon plastic bottle
Application Characteristics:
Clarity – Clear and colorless when dry
Leveling – Excellent
Defoaming - Excellent
Drying Time – 2-3 hours
Pot Life – THE FINISH/HARDENER MIXTURE MUST BE USED WITHIN 4 HOURS AFTER IT IS
MIXED. Product properties are diminished after 4 hours. The finish and hardener can only be mixed one
time.
Coverage – 350-400 square feet per gallon
Percent Cured After 24 Hours – 75%
Maximum Cure – 100% after 1 week
Recommended Use
Commercial and residential use including shopping malls, restaurants, offices, retail stores, hospitals,
schools and nursing homes
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
is product has a maxmum VOC (Volatile Organic Com
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
COMPATIBILITY: Bona Naturale® will adhere to most stains and finishes after proper preparation and dry
times. Stain, sealer and finish results may vary widely depending on the wood species, especially on oily
and resinous Exotics. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE
COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using accepted
industry association methods. 2. For a stained floor, make your final cut with 80-100 grit paper and
screen to 80-100 grit. For an unstained floor, make your final cut with 80-100 grit paper and
disc/screen to 120-150 grit. This burnishing will reduce the amount of grain raise. 3. Use a Tampico
Brush on a buffer and vacuum thoroughly. 4. Tack with a dry Bona® Microfiber Mop or cloth to
remove dust. 5. Apply finish system.
THE BONA NATURALE® FINISH SYSTEM: Apply a Bona sealer or Bona stain and 2 coats of Bona
Naturale. Follow label directions. Adding a third coat of Bona Naturale is recommended in heavy-traffic
commercial and residential areas. Visit www.bona.com for additional product information.
Rev 05/11
This data sheet replaces all previous versions
page 1/2
®
Bona Naturale
Finishing
Technical data sheet
RECOMMENDED APPLICATORS: Bona® Roller, Bona® Cut-In Pad.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: SHAKE WELL BEFORE USING. DO NOT THIN. DO NOT ADD WATER. 1.
Shake Bona Naturale finish (Part A) well for 30 seconds. 2. Add Bona Naturale Hardener (Part B) to finish
(Part A). One 12.8 oz. bottle of hardener will activate one gallon of finish. To mix finish amounts of less
than one gallon, use a 1:10 ratio. 3. Immediately shake mixture vigorously for 30-45 seconds. 4. Insert
supplied filter into bottle only after adding hardener. 5. Let sit for 5-10 minutes before applying. BONA
NATURALE CANNOT BE REHARDENED.
FINISHING: 1. Pour a 6” wide line of Bona Naturale across the direction of the flooring, cut-in 12”-18”
away from wall. 2. Saturate the roller with finish. Make sure to roll over all areas where cut-in pad was
used. 3. Set roller down at back side of puddle and pull the roller towards you. Then push back in the
same path feathering past your start point. Do not apply pressure to the roller. Overlap your run by 25%.
Rolling too fast will cause drips to fly off the roller. 4. BE SURE YOU ARE USING THE RECOMMENDED
COVERAGE OF 350-400 SQ. FT. PER GALLON. DO NOT SPREAD TOO THIN. 5. Allow the first coat to
dry 2-3 hours. High humidity and/or low temperature conditions will extend the dry time (recommended
conditions of 65-80° F (18°C-27°C) 40-60% relative humidity). 6. For smoothest results, abrade with a
Bona® Conditioning Pad before applying final coat. Always vacuum and tack thoroughly with a slightly
water dampened Bona Microfiber Mop or cloth after abrading. Allow final coat to dry at least 24 hours
before use.
CAUTION! Do not recap finish/hardener mixture after 4 hours to avoid pressure build-up. Dispose of any
remaining product in accordance with local, state and federal regulations. Decontaminate empty hardener
(Part B) bottle prior to disposal by adding water to the one-quart line. Recap. Shake vigorously. Dispose
of.
POT LIFE: THE FINISH/HARDENER MIXTURE MUST BE USED WITHIN 4 HOURS AFTER IT IS
MIXED. Product properties are diminished after 4 hours. The finish and hardener can only be mixed one
time.
INTERCOAT ABRASION: It is not necessary to abrade between Bona waterborne sealer and finish coats
unless more than 48 hours has passed since the previous coat was applied. For smoothest results,
abrade between all coats as necessary. When using solvent-based sealers, ALWAYS abrade before
finish coats. Always vacuum and tack thoroughly with a slightly water-dampened Bona Microfiber Mop or
cloth after abrading.
RECOATING: Be sure floor is free from wax, polish and oily residues. Follow the Bona Prep® system,
applying 1-2 coats of Bona Naturale finish. Delamination can occur if the Bona Prep process is not
followed; always test for compatibility.
Maintenance
CURING: The curing process takes approximately 7 days (75% cured after 1 day, 90% after 3 days). Do
not replace area rugs until the floor has fully cured. The floor may be walked on after 24 hours, but
remains susceptible to scuffing or marring until completely cured. Furniture may be placed onto floor after
72 hours (90% cured). Do not drag or slide furniture. Use only a dry Bona Microfiber Mop or cloth for
cleaning during the first week.
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container.
FLOOR CARE: Put walk-off mats at all entrance doorways to minimize dirt and grit. Sweep or vacuum
daily and damp-wipe as needed with Bona® Hardwood Floor Cleaner. Use felt pads under furniture legs
and appliances.
STORAGE: Nonflammable - Bona Naturale and Hardener should be stored in a climate controlled
environment. KEEP FROM FREEZING. Do not store above 100° F (38°C).
Order Information
Item#: WT190618001
Size: 1 Gallon
#/Case: 2
Rev 05/11
This data sheet replaces all previous versions
page 2/2
Bona Indoor Wood Oil
Finishing
Technical data sheet
Bona Indoor Wood Oil is a waterborne hardening oil designed to penetrate, seal and protect
hardwood floors, while preserving the natural appearance and elegance of the wood.
Fast turn around time, floors can be treated with one application and ready for use in one day
Available in seven colors – Clear, White, Grey, Black, Light Oak, Dark Oak & Mahogany
SM
GREENGUARD Children & Schools Certified
Made from natural vegetable oils
Easy to repair
Water & soap clean-up
Technical data
Physical Characteristics:
Ingredients
Clear, Light Oak, Dark Oak, Mahogany - Alkyd resin, Linseed oil, DPnB - Dipropylene glycol nbutyl ether, Water, Fatty acid ester
Black - Alkyd resin, Linseed oil, DPnB - Dipropylene glycol n-butyl ether, Water, Carbon black
White, Grey - Alkyd resin, Linseed oil, DPnB - Dipropylene glycol n-butyl ether, Water, Titanium
dioxide
Colors – Clear, Light Oak, Dark Oak, Mahogany, Black, Grey and White
Solids – 90%
Density – 8.0-9.15 lbs/gal (0.96-1.05 S.G.)
US Regulatory VOC – 100 g/L
Odor – Non-offending
Stability – 1 year shelf life in unopened container
Packaging – 1-quart metal cans
Application Characteristics:
Clarity – Semi-transparent
Leveling – N/A
Defoaming - N/A
Drying Time – 24 hours
Coverage – 450-500 square feet per quart
Percent Cured After 24 Hours – 70%
Maximum Cure – 100% after 1 week
Recommended Use
Residential- kitchens, entryways, family rooms, homes with pets, children and high foot traffic
Commercial- restaurants, offices, retail stores
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
COMPATIBILITY: Product results may vary widely depending on the wood species, especially on
oily and resinous Exotics. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE
COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using accepted
industry association methods. 2. Make your final cut with 100-120 grit paper and screen to 120150 grit. 3. Use a Tampico Brush on a dust containment buffer and vacuum thoroughly. 4. Tack
with a dry Bona® Microfiber Mop or cloth. 5. Apply Bona Indoor Wood Oil.
THE BONA INDOOR WOOD OIL SYSTEM: Bona Indoor Wood Oil is designed to penetrate and
seal bare wood in a single coat. In rare instances a second application may be necessary for even
coverage and color appearance. Colors may be mixed with all other Bona Indoor Wood Oil colors
to create custom blends. Visit www.bona.com for additional product information.
RECOMMENDED APPLICATOR & TOOLS: stainless steel trowel, rubber squeegee, stain
applicator pad.
MIXING INSTRUCTIONS: SHAKE AND STIR WELL BEFORE USING. DO NOT THIN.
Rev 03/12
This data sheet replaces all previous versions
page 1/2
Bona Indoor Wood Oil
Finishing
Technical data sheet
APPLICATION – NEWLY SANDED WOOD: 1. After preparing surface, apply Bona Indoor Wood
Oil by hand using a stainless steel trowel or rubber squeegee; or with a stain applicator pad driven
by a 175-rpm buffer. Apply at the coverage rate of 450-500 square feet per quart. 2. Allow
approximately 15-20 minutes for oil to penetrate. 3. Remove excess oil and blend areas using
buffer and a clean, cotton cloth wrapped around a 1” red buffing pad. Change cotton cloth as
needed. 4. Allow oil to dry thoroughly before use (minimum 24 hours under ideal conditions of 6080°F and 35-75% relative humidity). High humidity and or low temperature conditions will extend
dry time, while increased ventilation and airflow will reduce dry time.
APPLICATION – PREVIOUSLY OILED WOOD: 1. Clean surface thoroughly with Bona Natural Oil
Floor Cleaner and allow to dry. 2. Complete any necessary repairs to floor, final sanding to 120 grit.
3. Apply one thin coat of Bona Indoor Oil by hand using a stainless steel trowel or rubber
squeegee; or with a stain applicator pad driven by a 175-rpm buffer. Apply at the coverage rate of
550-600 square feet per quart. 4. Allow approximately 15-20 minutes for oil to penetrate.
5. Remove excess oil and blend areas using buffer and a clean, cotton cloth wrapped around a 1”
red buffing pad. Change cotton cloth as needed. 6. Allow oil to dry thoroughly before use
(minimum 24 hours under ideal conditions of 60-80°F and 35-75% relative humidity). High humidity
and or low temperature conditions will extend dry time, while increased ventilation and airflow will
reduce dry time.
Maintenance
CURING: The curing process takes approximately 7 days. Do not replace area rugs until the floor
has fully cured. The floor may be walked on after 24 hours. Use only a dry Bona Microfiber Mop or
cloth for cleaning during the first week.
CLEAN-UP: Clean tools with water and soap when wet, and mineral spirits when dry. Store tools
in an airtight container.
FLOOR CARE: Put walk-off mats at all entrance doorways to keep out excessive dirt and grit.
®
Sweep or vacuum daily and damp-wipe as needed with Bona Professional Series Natural Oil
Floor Cleaner. Use felt pads under furniture legs and appliances.
STORAGE: Bona Indoor Wood Oil should be stored in a climate-controlled environment. KEEP
FROM FREEZING. Do not store above 100° F.
Order Information
Item #
WO100012001
WO101012001
WO102012001
WO103012001
WO105012001
WO106012001
WO104012001
Size
1 Quart Clear
1 Quart Black
1 Quart White
1 Quart Grey
1 Quart Light Oak
1 Quart Dark Oak
1 Quart Mahogany
AT954233
AT32086000
Applicator Squeegee 1
Wipe-off cloths
10
Rev 03/12
This data sheet replaces all previous versions
#/Case
6
6
6
6
6
6
6
page 2/2
™
Bona Traffic HD
Finishing
Technical data sheet
Bona Traffic HD™ is for hardwood floor owners with an uncompromising attitude towards durability, being
green and looking beautiful. When the wood matters - Bona Traffic HD™.
Significantly outperforms all urethane finishes, including Bona Traffic®, in durability at 24 hours
Unsurpassed scuff, scratch and chemical resistance at full cure
Very low VOCs - less than 125
Very low odor
Clear and colorlesss, which highlights the true color of stained or natural wood floors. Will not change
color over time, allowing for easy touch-up
GREENGUARD Indoor Air Quality Certified®
No sealer needed over a stained floor
Exceptional build with excellent flow and leveling
Available in Commercial Satin, Commercial Semi-Gloss, and Commercial Extra Matte
Fast drying – approximately 2-3 hours
Nonflammable with a non-offending odor
Water clean-up
Technical data
Physical Characteristics:
Ingredients – Water, Polymer(s), and amorphous silica
Color – Milky white (wet)
pH – 7.9
Solids – 34% (with hardener)
Density – 8.70 lbs./gallon (1.04 S.G.)
US Regulatory VOC Compliant – 125 g/L (with hardener)
Coefficient of Friction - = 0.5
Gloss Level – (60°) – 7-10 for Commercial Extra Matte, 15-20 for Commercial Satin,
40-45 for Commercial Semi-Gloss
Odor – Very slight non-offensive odor
Stability – 1 year shelf life in unopened container
Packaging – 1-gallon plastic bottle
Application Characteristics:
Clarity – Clear and colorless when dry
Leveling – Excellent
Defoaming – Excellent
Drying Time – 2-3 hours
Pot Life – THE FINISH/HARDENER MIXTURE MUST BE USED WITHIN 4 HOURS AFTER IT IS
MIXED. Product properties are diminished after 4 hours. The finish and hardener can only be mixed one
time.
Coverage – 350-400 square feet per gallon
Percent Cured After 24 Hours – 80%, 72 hours – 90%
Maximum Cure – 100% after 1 week
Recommended Use
Commercial and residential use including shopping malls, restaurants, offices, retail stores, theater
stages, hospitals, schools, and nursing homes
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using accepted industry
association methods. 2. For a stained floor, make your final cut with 80-100 grit paper and screen to 80100 grit. For an unstained floor, make your final cut with 80-100 grit paper and disc/screen to 120-150
grit. This burnishing will reduce the amount of grain raise. 3. Use a Tampico Brush on a buffer and
vacuum thoroughly. 4. Tack with a dry Bona® Microfiber Mop or cloth. 5. Apply finish system.
THE BONA TRAFFIC HD™ FINISH SYSTEM: Apply a Bona sealer or Bona stain and 2 coats of Bona
Traffic HD. Follow label directions. Adding a third coat of Bona Traffic Commercial is recommended in
heavy-traffic commercial and residential areas. Visit www.bona.com for additional product information.
RECOMMENDED APPLICATORS: Bona® Floor Coater, Bona® Roller, Bona® Cut-In pad.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: SHAKE WELL BEFORE USING. DO NOT THIN. DO NOT ADD WATER. 1.
Shake Bona Traffic finish (Part A) well for 30 seconds. 2. Add Bona Traffic Hardener (Part B) to finish
Rev 09/11
This data sheet replaces all previous versions
page 1/2
™
Bona Traffic HD
Finishing
Technical data sheet
(Part A). One 10.38 oz. bottle of hardener will activate one gallon of finish. To mix finish amounts of less
than one gallon, use a 1:11.33 ratio. 3. Immediately shake mixture vigorously for 30-45 seconds. 4. Insert
supplied filter into bottle only after adding hardener. 5. Let sit for 5-10 minutes before applying. BONA
TRAFFIC CANNOT BE REHARDENED.
FINISHING: 1. Pour a 6” wide line of finish along the starting wall. Go with the grain of the wood.
2. Using a pre-dampened applicator, draw the applicator forward with the grain of the wood,
moving the finish toward the opposite wall. To maintain a wet edge at all times, hold the applicator
at a snowplow angle. 3. At the end of each run, turn the applicator towards you and pad out the
applicator parallel to the wet edge. 4. Feather out all turns. Do not push too hard or too fast to avoid drips
flying off the applicator. 5. BE SURE YOU ARE USING THE RECOMMENDED COVERAGE OF 350-400
SQ. FT. PER GALLON. DO NOT SPREAD TOO THIN. 6. Allow the first coat to dry 2-3 hours. High
humidity and/or low temperature conditions will extend the dry time (recommended conditions of 65-80°
F/ 40-60% relative humidity). 7. For smoothest results, abrade with a Bona® Conditioning Pad before
applying final coat. Always vacuum and tack thoroughly with a slightly water dampened Bona Microfiber
Mop or cloth after abrading. Allow final coat to dry at least 48 hours before use.
CAUTION! Do not recap finish/hardener mixture after 4 hours to avoid pressure build-up. Dispose of any
remaining product in accordance with local, state and federal regulations. Decontaminate empty hardener
(Part B) bottle prior to disposal by adding water to the one-quart line. Recap. Shake vigorously. Dispose
of.
POT LIFE: THE FINISH/HARDENER MIXTURE MUST BE USED WITHIN 4 HOURS AFTER IT IS
MIXED. Product properties are diminished after 4 hours. The finish and hardener can be mixed only one
time.
INTERCOAT ABRASION: It is not necessary to abrade between Bona waterborne sealer and finish coats
unless more than 48 hours has passed since the previous coat was applied. For smoothest results,
abrade between all coats as necessary. When using solvent-based sealers, ALWAYS abrade before
finish coats. Always vacuum and tack thoroughly with a slightly water-dampened Bona Microfiber Mop or
cloth after abrading.
RECOATING:
BONA RECOAT SYSTEM: Guaranteed recoat system designed to safely remove all contaminants and
prepare the floor surface for optimal adhesion of Bona Traffic HD®. See Bona Recoat System for
application directions.
WHEN USING BONA PREP SYSTEM: Be sure floor is free from wax, polish and oily residues. Follow the
Bona Prep® system, applying 1-2 coats of Bona Traffic HD™ finish. Delamination can occur if the Bona
Prep process is not followed; always test for compatibility. NOTE: Bona Traffic HD™ will adhere to most
stains and finishes after proper preparation and dry times. Stain, sealer and finish results may vary widely
depending on the wood species, especially on oily and resinous Exotics. ALWAYS PREPARE A SAMPLE
OR TEST AREA TO DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
Maintenance
CURING: The curing process takes approximately 7 days, (80% cured after 1 day, 90% after 3 days). Do
not replace area rugs until the floor has fully cured. The floor may be walked on after 24 hours, but
remains susceptible to scuffing or marring until completely cured. Furniture may be placed onto floor after
72 hours (90% cured). Do not drag or slide furniture. Use only a dry Bona Microfiber Mop or cloth for
cleaning during the first week.
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container.
FLOOR CARE: Put walk-off mats at all entrance doorways to minimize dirt and grit. Sweep or vacuum
daily and damp-wipe as needed with Bona® Professional Series Hardwood Floor Cleaner. Use felt pads
under furniture legs and appliances.
STORAGE: Nonflammable - Bona Traffic and Hardener should be stored in a climate controlled
environment. KEEP FROM FREEZING. Do not store above 100° F (38° C).
Order Information
Item #
WT155918001
WT155618001
WT155318001
Size
1 Gallon – Extra Matte
1 Gallon – Satin
1 Gallon – Semi Gloss
Rev 09/11
This data sheet replaces all previous versions
No./Case
2
2
2
page 2/2
®
Bona Traffic Anti Slip
Finishing
Technical data sheet
Bona Traffic® Anti-Slip is a 100% polyurethane 2-component waterborne finish offering exceptional
durability and protection for hardwood floors. It has all the features of Bona Traffic® but with the additional
benefit of being formulated to meet the highest standards for slip resistance in workplaces and other
situations with an increased risk of wet spills. With its high friction, Bona Traffic Anti-Slip is an ideal choice
for stairs, nurseries, kitchens and similar locations.
Meets the ADA recommendation for accesible routes and ramps according to ASTM 2047
Meets the German Industrial Norm for slip resistance DIN 51 130 with a rating of R10
Clear and colorless, which highlights the true color of stained or natural wood floors. Will not change
color over time, allowing for easy touch-up
GREENGUARD certified for indoor air quality
No sealer needed over a stained floor
Exceptional build with excellent flow and leveling
Fast drying- Approximately 2-3 hours
Nonflammable with a non-offending odor
Water clean-up
Technical data
Physical Characteristics:
Ingredients – Water, polymeric resin, dipropylene glycol monomethyl ether, and amorphous silica.
Color – Milky white (wet)
pH – 7.5 - 7.9
Solids – 34% (with hardener)
Density – 8.70 lbs/gallon (1.04 S.G.)
US Regulatory VOC Compliant – 210 g/L
Coefficient of Friction = 0.8
Gloss Level – (60°) – Approximately 25
Odor – Non-offending, slight ammonia
Stability – One year shelf life in unopened container
Packaging – 1-gallon plastic bottle
Application Characteristics:
Clarity – Clear and colorless when dry
Leveling – Excellent
Defoaming – Excellent
Drying Time – 2-3 hours
Pot Life – THE FINISH/HARDENER MIXTURE MUST BE USED WITHIN 4 HOURS AFTER IT IS
MIXED. Product properties are diminished after 4 hours. The finish and hardener can only be mixed one
time.
Coverage – 350-400 square feet per gallon
Percent Cured After 24 Hours – 75%, 72 hours – 90%
Maximum Cure – 100% after 1 week
Recommended Use
Commercial and reisdential use including shopping malls, restaurants, offices, retail stores, theater
stages, hospitals, schools, and nursing homes, where slip resistance is required.
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
COMPATIBILITY: Bona Traffic Anti-Slip will adhere to most stains and finishes after proper preparation
and dry times. Stain, sealer and finish results may vary widely depending on the wood species, especially
on oily and resinous Exotics. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE
COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using accepted
industry association methods. 2. For a stained floor, make your final cut with 80-100 grit paper and
screen to 80-100 grit. For an unstained floor, make your final cut with 80-100 grit paper and disc/screen to
120-150 grit. This burnishing will reduce the amount of grain raise. 3. Use a Tampico Brush on a buffer
and vacuum thoroughly. 4. Tack with a dry Bona® Microfiber Mop or cloth. 5. Apply finish system.
THE BONA TRAFFIC® ANTI-SLIP FINISH SYSTEM: Apply a Bona sealer or Bona stain and 2 coats of
Bona Traffic Anti-Slip. Follow label directions. Adding a third coat of Bona Traffic Anti-Slip is
recommended in heavy-traffic commercial and residential areas. Visit www.bona.com for additional
product information.
RECOMMENDED APPLICATORS: Bona® Floor Coater, Bona® Roller, Bona® Cut-In pad.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
Rev 05/11
This data sheet replaces all previous versions
page 1/2
®
Bona Traffic Anti Slip
Finishing
Technical data sheet
MIXING INSTRUCTIONS: SHAKE WELL BEFORE USING. DO NOT THIN. DO NOT ADD WATER. 1.
Shake Bona Traffic Anti-Slip finish (Part A) well for 30 seconds. 2. Add Bona Traffic Hardener (Part B) to
finish (Part A). One 12.8 oz. bottle of hardener will activate one gallon of finish. To mix finish amounts of
less than one gallon, use a 1:10 ratio. 3. Immediately shake mixture vigorously for 30-45 seconds. 4.
Insert supplied filter into bottle only after adding hardener. 5. Let sit for 5-10 minutes before applying.
BONA TRAFFIC ANTI-SLIP CANNOT BE REHARDENED.
FINISHING: 1. Pour a 6” wide line of finish along the starting wall. Go with the grain of the wood.
2. Using a pre-dampened applicator, draw the applicator forward with the grain of the wood, moving the
finish toward the opposite wall. To maintain a wet edge at all times, hold the applicator at a snowplow
angle. 3. At the end of each run, turn the applicator towards you and pad out the applicator parallel to the
wet edge. 4. Feather out all turns. Do not push too hard or too fast to avoid drips flying off the applicator.
5. BE SURE YOU ARE USING THE RECOMMENDED COVERAGE OF 350-400 SQ. FT. PER GALLON.
DO NOT SPREAD TOO THIN. 6. Allow the first coat to dry 2-3 hours. High humidity and/or low
temperature conditions will extend the dry time (recommended conditions of 65-80°F/40-60% relative
humidity). 7. For smoothest results, abrade with a Bona® Conditioning Pad before applying final coat.
Always vacuum and tack thoroughly with a slightly water dampened Bona Microfiber Mop or cloth after
abrading. Allow final coat to dry at least 24 hours before use.
CAUTION! Do not recap finish/hardener mixture after 4 hours to avoid pressure build-up. Dispose of any
remaining product in accordance with local, state and federal regulations. Decontaminate empty hardener
(Part B) bottle prior to disposal by adding water to the one-quart line. Recap. Shake vigorously. Dispose
of.
POT LIFE: THE FINISH/HARDENER MIXTURE MUST BE USED WITHIN 4 HOURS AFTER IT IS
MIXED. Product properties are diminished after 4 hours. The finish and hardener can be mixed only one
time.
This product has a maximum VOC (Volatile Organic Compound) content of 210 grams per
INTERCOAT ABRASION: It is not necessary to abrade between Bona waterborne sealer and finish coats
unless more than 48 hours has passed since the previous coat was applied. For smoothest results,
abrade between all coats as necessary. When using solvent-based sealers, ALWAYS abrade before
finish coats. Always vacuum and tack thoroughly with a slightly water-dampened Bona Microfiber Mop or
cloth after abrading.
RECOATING: Be sure floor is free from wax, polish and oily residues. Follow the Bona Prep® system,
applying 1-2 coats of Bona Traffic Anti-Slip finish. Delamination can occur if the Bona Prep process is not
followed and the floor has not been tested for compatibility.
Maintenance
CURING: The curing process takes approximately 7 days, (75% cured after 1 day, 90% after 3 days). Do
not replace area rugs until the floor has fully cured. The floor may be walked on after 24 hours, but
remains susceptible to scuffing or marring until completely cured. Furniture may be placed onto floor after
72 hours (90% cured). Do not drag or slide. Use only a dry Bona Microfiber Mop or cloth for cleaning
during the first week.
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container.
FLOOR CARE: Put walk-off mats at all entrance doorways to keep out excessive dirt and grit. Sweep or
vacuum daily and damp-wipe as needed with Bona® Hardwood Floor Cleaner. Use Bona® Self-Adhesive
Felt Pads under furniture legs and appliances.
STORAGE: Nonflammable - Bona Traffic Anti-Slip and Hardener should be stored in a climate-controlled
environment. KEEP FROM FREEZING. Do not store above 100° F.
Order Information
Item #: WT153918001
Size: 1 Gallon
#/Case: 2
Rev 05/11
This data sheet replaces all previous versions
page 2/2
®
Bona Traffic
Finishing
Technical data sheet
For heavy-traffic commercial and residential hardwood floors, Bona Traffic® provides the ultimate in
durability and beauty, outperforming any finish in the industry- moisture cure, solvent-based, oil-modified
or other waterborne finishes.
Unsurpassed durability – outperforms moisture cure finishes without the hazardous side effects, and
with all the benefits of a waterborne finish
The application feel of a solvent-based finish
Faster curing rate allows quicker access to the floor
Clear and colorless, which highlights the true color of stained or natural wood floors. Will not change
color over time, allowing for easy touch-up
GREENGUARD certified for indoor air quality
Classified by Underwriters Laboratories Inc. as to slip resistance only, Control #21KM
No sealer needed over a stained floor
Exceptional build with excellent flow and leveling
Available in Commercial Satin, Commercial Semi-Gloss, and Commercial Gloss
Fast drying – approximately 2-3 hours
Nonflammable with a non-offending odor
Water clean-up
Technical data
Physical Characteristics:
Ingredients – Water, polymeric resin, dipropylene glycol monomethyl ether,2,6,8-trimethyl-4nonypolyethylene glycol ether, and amorphous silica.
Color – Milky white (wet)
pH – 7.9
Solids – 34% (with hardener)
Density – 8.70 lbs./gallon (1.04 S.G.)
US Regulatory VOC Compliant – 210 g/L (with hardener)
Coefficient of Friction - = 0.5
Gloss Level – (60°) – 15-20 for Commercial Satin
40-45 for Commercial Semi-Gloss
65-70 for Commercial Gloss
Odor – Non-offending, slight ammonia
Stability – 1 year shelf life in unopened container
Packaging – 1-gallon plastic bottle
Application Characteristics:
Clarity – Clear and colorless when dry
Leveling – Excellent
Defoaming – Excellent
Drying Time – 2-3 hours
Pot Life – THE FINISH/HARDENER MIXTURE MUST BE USED WITHIN 4 HOURS AFTER IT IS
MIXED. Product properties are diminished after 4 hours. The finish and hardener can only be mixed one
time.
Coverage – 350-400 square feet per gallon
Percent Cured After 24 Hours – 75%, 72 hours – 90%
Maximum Cure – 100% after 1 week
Recommended Use
Commercial and residential use including shopping malls, restaurants, offices, retail stores, theater
stages, hospitals, schools, and nursing homes
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
COMPATIBILITY: Bona Traffic® will adhere to most stains, sealers and finishes after proper preparation
and dry times. Stain, sealer and finish results may vary widely depending on the wood species, especially
on oily and resinous Exotics. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE
COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using accepted
industry association methods. 2. For a stained floor, make your final cut with 80-100 grit paper and
screen to 80-100 grit. For an unstained floor, make your final cut with 80-100 grit paper and
disc/screen to 120-150 grit. This burnishing will reduce the amount of grain raise. 3. Use a Tampico
Brush on a buffer and vacuum thoroughly. 4. Tack with a dry Bona® Microfiber Mop or cloth to
remove dust. 5. Apply finish system.
Rev 09/11
This data sheet replaces all previous versions
page 1/2
®
Bona Traffic
Finishing
Technical data sheet
THE BONA TRAFFIC® FINISH SYSTEM: Apply a Bona sealer or Bona stain and 2 coats of Bona
Traffic®. Follow label directions. Adding a third coat of Bona Traffic is recommended in heavy-traffic
commercial and residential areas. Visit www.bona.com for additional product information.
RECOMMENDED APPLICATORS: Bona® Floor Coater (T-bar), Bona® Roller, Bona® Cut-In pad.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: SHAKE WELL BEFORE USING. DO NOT THIN. DO NOT ADD WATER. 1.
Shake Bona Traffic finish (Part A) well for 30 seconds. 2. Add Bona Traffic Hardener (Part B) to finish
(Part A). One 12.8 oz. bottle of hardener will activate one gallon of finish. To mix finish amounts of less
than one gallon, use a 1:10 ratio. 3. Immediately shake mixture vigorously for 30-45 seconds. 4. Insert
supplied filter into bottle only after adding hardener. 5. Let sit for 5-10 minutes before applying. BONA
TRAFFIC CANNOT BE REHARDENED.
FINISHING: 1. Pour a 6” wide line of finish along the starting wall. Go with the grain of the wood.
2. Using a pre-dampened T-bar sleeve, draw the applicator forward with the grain of the wood,
moving the finish toward the opposite wall. To maintain a wet edge at all times, hold the applicator
at a snowplow angle. 3. At the end of each run, turn the applicator towards you and pad out the
applicator parallel to the wet edge. 4. Feather out all turns. Do not push too hard or too fast to avoid drips
flying off the applicator. 5. BE SURE YOU ARE USING THE RECOMMENDED COVERAGE OF 350-400
SQ. FT. PER GALLON. DO NOT SPREAD TOO THIN. 6. Allow the first coat to dry 2-3 hours. High
humidity and/or low temperature conditions will extend the dry time (recommended conditions of 65-80° F
(18°C-27°C) 40-60% relative humidity). 7. For smoothest results, abrade with a Bona® Conditioning Pad
before applying final coat. Always vacuum and tack thoroughly with a slightly water dampened Bona
Microfiber Mop or cloth after abrading. Allow final coat to dry at least 24 hours before use.
CAUTION! Do not recap finish/hardener mixture after 4 hours to avoid pressure build-up. Dispose of any
remaining product in accordance with local, state and federal regulations. Decontaminate empty hardener
(Part B) bottle prior to disposal by adding water to the one-quart line. Recap. Shake vigorously. Dispose
of.
POT LIFE: THE FINISH/HARDENER MIXTURE MUST BE USED WITHIN 4 HOURS AFTER IT IS
MIXED. Product properties are diminished after 4 hours. The finish and hardener can be mixed only one
time.
INTERCOAT ABRASION: It is not necessary to abrade between Bona waterborne sealer and finish coats
unless more than 48 hours has passed since the previous coat was applied. For smoothest results,
abrade between all coats as necessary. When using solvent-based sealers, ALWAYS abrade before
finish coats. Always vacuum and tack thoroughly with a slightly water-dampened Bona Microfiber Mop or
cloth after abrading.
RECOATING:
BONA RECOAT SYSTEM: Guaranteed recoat system designed to safely remove all contaminants and
prepare the floor surface for optimal adhesion of Bona Traffic®. See Bona Recoat System for application
directions.
WHEN USING BONA PREP SYSTEM: Be sure floor is free from wax, polish and oily residues. Follow the
Bona Prep® system, applying 1-2 coats of Bona Traffic® finish. Delamination can occur if the Bona Prep
process is not followed; always test for compatibility. NOTE: Bona Traffic® will adhere to most stains and
finishes after proper preparation and dry times. Stain sealer and finish results may vary widely depending
on the wood species, especially on oily and resinous exotics. ALWAYS PREPARE A SAMPLE OR TEST
AREA TO DETERMINE COMPATABILITY, APPEARANCE AND DESIRED RESULTS.
Maintenance
CURING: The curing process takes approximately 7 days, (75% cured after 1 day, 90% after 3 days). Do
not replace area rugs until the floor has fully cured. The floor may be walked on after 24 hours, but
remains susceptible to scuffing or marring until completely cured. Furniture may be placed onto floor after
72 hours (90% cured). Do not drag or slide furniture. Use only a dry Bona Microfiber Mop or cloth for
cleaning during the first week.
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container.
FLOOR CARE: Put walk-off mats at all entrance doorways to minimize dirt and grit. Sweep or vacuum
daily and damp-wipe as needed with Bona® Hardwood Floor Cleaner. Use felt pads under furniture legs
and appliances.
STORAGE: Nonflammable - Bona Traffic and Hardener should be stored in a climate controlled
environment. KEEP FROM FREEZING. Do not store above 100° F (38° C).
Order Information
Item #
WT154218001
WT150318075
WT150618075
Size
1 Gallon – Gloss
1 Gallon – Semi Gloss
1 Gallon – Satin
Rev 09/11
This data sheet replaces all previous versions
No./Case
2
2
2
page 2/2
Bona Mega® Clear HD™
Finishing
Technical data sheet
®
®
Bona Mega Clear HD™ takes Bona Mega to the next level. The addition of a second
component and the removal of the amber tint combine to increase the physical performance and
®
provide a new look to the Bona Mega family. These new options allow the floor owner and
contractor to meet various performance and appearance demands at an incredible value.
No amber tint – finish will not yellow over time
2 component, crosslinked formula
®
- Improved chemical resistance over Bona Mega
®
- Increased scuff/scratch resistance over Bona Mega
No limited pot life and no wasted finish
Exceptional build and clarity
Excellent flow and leveling
Available in gloss, semi-gloss or satin
®
GREENGUARD Indoor Air Quality Certified
Fast drying – Approximately 2-3 hours
Nonflammable and virtually odorless
Water clean-up
Technical data
Physical Characteristics:
Ingredients – Water, Polymer(s), Diethylene Glycol Monoethyl Ether.
Color – Milky white (wet)
pH – 7.9
Solids – 30%
Density – 8.75 lbs./gallon (1.05 S.G.)
US Regulatory VOC – 250 g/L
Gloss Level (60°) >85 for gloss, 45-55 for semi-gloss, 25-35 for satin
Odor – Non-offending
Stability – 1 year shelf life in unopened container
Packaging – 1-gallon plastic bottle + 2.5oz plastic bottle
Application Characteristics:
Clarity – Clear when dry
Leveling – Excellent
Defoaming - Excellent
Drying Time – 2-3 hours
Coverage – 500-600 square feet per gallon
Percent Cured After 24 Hours – 70%
Maximum Cure – 100% after 1 week
Recommended Use
Heavy-traffic residential- kitchens, entryways, family rooms, homes with pets, children and
high foot traffic
Commercial- restaurants, offices, retail stores
Hospitals, schools and universities, nursing homes
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
®
COMPATIBILITY: Bona Mega Clear HD will adhere to most stains and finishes after proper
preparation and dry times. Stain, sealer and finish results may vary widely depending on the wood
species, especially on oily and resinous Exotics. Bona Mega will appear slightly amber on white,
bleached or pastel floors. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE
COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using accepted
industry association methods. 2. For a stained floor, make your final cut with 80-100 grit paper and
screen to 80-100 grit. For an unstained floor, make your final cut with 80-100 grit paper and
disc/screen to 120-150 grit. This burnishing will reduce the amount of grain raise. 3. Use a Tampico
®
Brush on a buffer and vacuum thoroughly. 4. Tack with a dry Bona Microfiber Mop or cloth to
remove dust. 5. Apply finish system.
Rev 03/12
This data sheet replaces all previous versions
page 1/2
Bona Mega® Clear HD™
Finishing
Technical data sheet
THE BONA MEGA CLEAR HD FINISH SYSTEM: Apply a Bona sealer or Bona stain and 2 coats
of Bona Mega Clear HD. Follow label directions. Adding a third coat of Bona Mega Clear HD is
recommended in heavy-traffic commercial and residential areas. Visit www.bona.com for additional
product information.
®
®
®
RECOMMENDED APPLICATORS: Bona Floor Coater (T-bar), Bona Roller, Bona Cut-In Pad.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: SHAKE WELL BEFORE USING. DO NOT THIN. DO NOT ADD
WATER.
1. Shake Bona Mega Clear HD finish (Part A) well for 30 seconds. 2. Open the crosslinker bottle
and add an equal part of water to the crosslinker. Shake well. 3. Add crosslinker & water mixture
to Bona Mega Clear HD within 15minutes. 4. Insert supplied filter into bottle only after adding
crosslinker. 5. Shake vigorously and let sit 5-10 minutes.
FINISHING: 1. Pour a 6 wide line of finish along the starting wall. Go with the grain of the wood.
2. Using a pre-dampened applicator, draw the applicator forward with the grain of the wood,
moving the finish toward the opposite wall. To maintain a wet edge at all times, hold the applicator
at a snowplow angle. 3. At the end of each run, turn the applicator towards you and pad out the
applicator parallel to the wet edge. 4. Feather out all turns. Do not push too hard or too fast to
avoid drips flying off the applicator. 5. BE SURE YOU ARE USING THE RECOMMENDED
COVERAGE OF 500-600 SQ. FT. PER GALLON. DO NOT SPREAD TOO THIN. 6. Allow the first
coat to dry 2-3 hours. High humidity and/or low temperature conditions will extend the dry time
(recommended conditions of 65-80°F/40-60% relative humidity). 7. For smoothest results, abrade
®
with a Bona Conditioning Pad before applying final coat. Always vacuum and tack thoroughly with
a slightly water dampened Bona Microfiber Mop or cloth after abrading. Allow final coat to dry at
least 24 hours before use.
POT LIFE: The finish/crosslinker mixture is active for 8 hours after it is mixed. Within 2-3 days,
crosslinker may be added one additional time.
INTERCOAT ABRASION: It is not necessary to abrade between Bona waterborne sealer and
finish coats unless more than 48 hours has passed since the previous coat was applied. For
smoothest results, abrade between all coats as necessary. When using solvent-based sealers,
ALWAYS abrade before finish coats. Always vacuum and tack thoroughly with a slightly waterdampened Bona Microfiber Mop or cloth after abrading.
®
RECOATING: Be sure floor is free from wax, polish and oily residues. Follow the Bona Prep
system, applying 1-2 coats of Bona Mega Clear HD. If Recoating a Factory Prefinished Floor, DO
®
®
NOT USE Bona Mega finish. Use Bona Naturale or Bona Traffic finishes with the Bona Prep
system. Delamination can occur if the Bona Prep process is not followed; always test for
compatibility.
Maintenance
CURING: The curing process takes approximately 7 days, (70% cured after 1 day, 90% after 3
days). Do not replace area rugs until the floor has fully cured. The floor may be walked on after 24
hours, but remains susceptible to scuffing or marring until completely cured. Furniture may be
placed onto floor after 72 hours (90% cured). Do not drag or slide furniture. Use only a dry Bona
Microfiber Mop or cloth for cleaning during the first week.
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container.
FLOOR CARE: Put walk-off mats at all entrance doorways to minimize dirt and grit. Sweep or
®
vacuum daily and damp-wipe as needed with Bona Hardwood Floor Cleaner. Use felt pads under
furniture legs and appliances.
STORAGE: Nonflammable - Bona Mega Clear HD should be stored in a climate controlled
environment. KEEP FROM FREEZING. Do not store above 100° F. (38° C)
Order Information
Item #
WT200018001
WT200318001
WT200618001
Size
1 Gallon-Gloss
1 Gallon-Semi-Gloss
1 Gallon- Satin
Rev 03/12
This data sheet replaces all previous versions
#/Case
3
3
3
page 2/2
®
Bona Mega
Finishing
Technical data sheet
®
Bona Mega is the revolutionary, oxygen-crosslinking, waterborne wood floor finish for use on
heavy-traffic interior residential and commercial floors.
Bona Mega’s unique OCP (Oxygen-Crosslinking Polyurethane) formula uses the oxygen in the air
®
as the crosslinker. Bona Mega is the world’s leading waterborne finish, providing exceptional
durability, beauty and value.
Oxygen-crosslinking, 100% polyurethane waterborne formula with extraordinary performance,
ease of application and durability
No limited pot life and no wasted finish
Natural wood color enhances the beauty of the wood
Exceptional build and clarity
Excellent flow and leveling
Available in gloss, semi-gloss or satin
GREENGUARD certified for indoor air quality
Fast drying – Approximately 2-3 hours
Nonflammable and virtually odorless
Water clean-up
Technical data
Physical Characteristics:
Ingredients – Water, polymeric resins, propylene based glycol ethers, silica derivate, surfactants.
Color – Milky white (wet)
pH – 7.9
Solids – 32.5%
Density – 8.75 lbs./gallon (1.05 S.G.)
US Regulatory VOC – 150 g/L
Gloss Level (60°) >90 for gloss, 45-50 for semi-gloss, 25-30 for satin
Odor – Non-offending
Stability – 1 year shelf life in unopened container
Packaging – 1-gallon plastic bottle
Application Characteristics:
Clarity – Clear when dry
Leveling – Excellent
Defoaming - Excellent
Drying Time – 2-3 hours
Coverage – 500-600 square feet per gallon
Percent Cured After 24 Hours – 70%
Maximum Cure – 100% after 1 week
Recommended Use
Heavy-traffic residential- kitchens, entryways, family rooms, homes with pets, children and
high foot traffic
Commercial- restaurants, offices, retail stores
Hospitals, schools and universities, nursing homes
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
®
COMPATIBILITY: Bona Mega will adhere to most stains and finishes after proper preparation and
dry times. Stain, sealer and finish results may vary widely depending on the wood species,
especially on oily and resinous Exotics. Bona Mega will appear slightly amber on white, bleached
or pastel floors. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE
COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using accepted
industry association methods. 2. For a stained floor, make your final cut with 80-100 grit paper and
screen to 80-100 grit. For an unstained floor, make your final cut with 80-100 grit paper and
disc/screen to 120-150 grit. This burnishing will reduce the amount of grain raise. 3. Use a Tampico
®
Brush on a buffer and vacuum thoroughly. 4. Tack with a dry Bona Microfiber Mop or cloth to
remove dust. 5. Apply finish system.
Rev 05/11
This data sheet replaces all previous versions
page 1/2
®
Bona Mega
Finishing
Technical data sheet
®
THE BONA MEGA FINISH SYSTEM: Apply a Bona sealer or Bona stain and 2 coats of Bona
Mega. Follow label directions. Adding a third coat of Bona Mega is recommended in heavy-traffic
commercial and residential areas. Visit www.bona.com for additional product information.
®
®
®
RECOMMENDED APPLICATORS: Bona Floor Coater (T-bar), Bona Roller, Bona Cut-In Pad.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: SHAKE WELL BEFORE USING. DO NOT THIN. DO NOT ADD
WATER. Insert supplied filter.
FINISHING: 1. Pour a 4” wide line of finish along the starting wall. Go with the grain of the wood.
2. Using a pre-dampened T-bar sleeve, draw the applicator forward with the grain of the wood,
moving the finish toward the opposite wall. To maintain a wet edge at all times, hold the applicator
at a snowplow angle. 3. At the end of each run, turn the applicator towards you and pad out the
applicator parallel to the wet edge. 4. Feather out all turns. Do not push too hard or too fast to
avoid drips flying off the applicator. 5. BE SURE YOU ARE USING THE RECOMMENDED
COVERAGE OF 500-600 SQ. FT. PER GALLON. DO NOT SPREAD TOO THIN. 6. Allow the first
coat to dry 2-3 hours. High humidity and/or low temperature conditions will extend the dry time
(recommended conditions of 65-80° F (18°C-27° C) 40-60% relative humidity). 7. For smoothest
®
results, abrade with a Bona Conditioning Pad before applying final coat. Always vacuum and tack
thoroughly with a slightly water dampened Bona Microfiber Mop or cloth after abrading. Allow final
coat to dry at least 24 hours before use.
INTERCOAT ABRASION: It is not necessary to abrade between Bona waterborne sealer and
finish coats unless more than 48 hours has passed since the previous coat was applied. For
smoothest results, abrade between all coats as necessary. When using solvent-based sealers,
ALWAYS abrade before finish coats. Always vacuum and tack thoroughly with a slightly waterdampened Bona Microfiber Mop or cloth after abrading.
®
RECOATING: Be sure floor is free from wax, polish and oily residues. Follow the Bona Prep
system, applying 1-2 coats of Bona Mega. If Recoating a Factory Prefinished Floor, DO NOT USE
®
®
Bona Mega finish. Use Bona Naturale or Bona Traffic finishes with the Bona Prep system.
Delamination can occur if the Bona Prep process is not followed; always test for compatibility.
Maintenance
CURING: The curing process takes approximately 7 days, (70% cured after 1 day, 90% after 3
days). Do not replace area rugs until the floor has fully cured. The floor may be walked on after 24
hours, but remains susceptible to scuffing or marring until completely cured. Furniture may be
placed onto floor after 72 hours (90% cured). Do not drag or slide furniture. Use only a dry Bona
Microfiber Mop or cloth for cleaning during the first week.
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container.
FLOOR CARE: Put walk-off mats at all entrance doorways to minimize dirt and grit. Sweep or
®
vacuum daily and damp-wipe as needed with Bona Hardwood Floor Cleaner. Use felt pads under
furniture legs and appliances.
STORAGE: Nonflammable - Bona Mega should be stored in a climate controlled environment.
KEEP FROM FREEZING. Do not store above 100° F. (38° C)
Order Information
Item #
WT130018001
WT130318001
WT130618001
Size
1 Gallon-Gloss
1 Gallon-Semi-Gloss
1 Gallon- Satin
Rev 05/11
This data sheet replaces all previous versions
#/Case
3
3
3
page 2/2
™
Bona Mega Booster
Finishing
Technical data sheet
Bona Mega Booster™ is the newest innovation to the Bona waterborne finish family. This performance
enhancing additive for Bona Mega® promotes increased durability, chemical resistance and adhesion. Combined
with Bona Mega it is ideal for prolonging the life and enhancing the beauty of residential and commercial wood
floors.
Promotes maximum durability
Increased chemical resistance
Increased adhesion, allowing Bona Mega® with Bona Mega Booster™ to be used on re-coats
Exceptional build and clarity
Excellent flow and leveling
GREENGUARD certified for indoor air quality.
Fast drying - Approximately 2-3 hours
Technical data
Physical Characteristics:
Ingredients – Polyfunctional aziridine, diethylene glycol monoethyl ether acetate, and dipropylene glycol
monomethyl ether.
Color – Milky white (wet)
pH – 7.9
Solids – 31.5%
Density – 8.68 lbs/gallon (1.04 S.G.)
US Regulatory VOC– 250 g/L when used with Bona Mega®
Gloss Level – (60°) >90 for gloss, 45-50 for semi-gloss, 25-30 for satin
Odor – Non-offending
Stability – 1 year shelf life in unopened container
Packaging – 8 oz. plastic bottle – Mega Booster only
Application Characteristics:
Clarity – Clear when dry
Leveling – Excellent
Defoaming - Excellent
Drying Time – 2-3 hours
Coverage – 500-600 square feet per gallon
Percent Cured After 24 Hours – 70%
Maximum Cure – 100% after 1 week
Recommended Use
Heavy-traffic residential- kitchens, entryways, family rooms, homes with pets, children and high foot traffic
Commercial- restaurants, offices, retail stores
Hospitals, schools and universities, nursing homes
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET FOR THIS PRODUCT.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
MIXING INSTRUCTIONS: ONLY MIX BONA MEGA BOOSTER™ WITH BONA MEGA FINISH. DO NOT THIN.
DO NOT ADD WATER.
1. Shake Bona Mega® finish (Part A) well for 30 seconds. 2. Add Bona Mega Booster (Part B) to finish (Part A).
One bottle of Bona Mega Booster will activate one gallon of Bona Mega. To mix finish amounts of less than one
gallon, use a 1:16 ratio. 3. Immediately shake mixture vigorously for 15 to 30 seconds. 4. Insert supplied filter
into Bona Mega bottle. 5. Let sit for 5-10 minutes before applying.
POT LIFE: The finish/booster mixture is active for 8 hours after it is mixed. Within 2-3 days, Bona Mega Booster
may be added one additional time.
Maintenance
STORAGE: Bona Mega Booster should be stored in a climate- controlled environment. KEEP FROM
FREEZING. Do not store above 100º F (38º C).
Order Information
Item#: WH800061001
Size: 8 oz.
#/Case: 12
Rev 05/11
This data sheet replaces all previous versions
page 1/1
Bona Novia
™
Finishing
Technical data sheet
Unsurpassed flow and leveling, defoaming, and numerous application options make Bona Novia
the easiest to use waterborne finish on the market. When Bona Novia is used with Bona
™
AmberSeal , it is a budget sensitive, dependable alternative to any oil-based system.
™
Developed especially to replace oil-based finishes
Clear and colorless, which highlights the true color of stained or natural wood floors. Will not
change color over time, allowing for easy touch-up
Forgiving/easy application. Can be applied with most applicators using a variety of techniques
One-component. No limited pot life or wasted finish
Exceptional build and clarity
Excellent flow and leveling
GREENGUARD certified for indoor air quality
Fast drying – Approximately 2-3 hours
Non-flammable and virtually odorless
Water clean-up
Available in Gloss, Semi-gloss, or Satin
Technical data
Physical Characteristics:
Ingredients: Water, polymeric resins, dipropylene glycol monomethyl ether, dipropylene glycol nbutyl ether
Color – Milky white (wet)
pH – 7.5 – 7.9
Solids – 30 – 32%
Density – 8.70 lbs./gallon (1.04 S.G.)
US Regulatory VOC – 220 g/L
Gloss Level – (60°) – >85 for gloss, 45-50 for semi-gloss, 25-30 for satin
Odor – Non-offending
Stability – 1 year shelf life in unopened container
Packaging – 1-gallon plastic bottle
Application Characteristics:
Clarity – Clear and colorless when dry
Leveling – Excellent
Defoaming - Excellent
Drying Time – 2-3 hours
Coverage – 500-600 square feet per gallon
Percent Cured After 24 Hours – 70%
Maximum Cure – 100% after 1 week
Recommended Use
Residential- kitchens, entryways, family rooms, homes with pets, and/or children
Anywhere an oil-based finish would be used
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
COMPATIBILITY: Bona Novia™ will adhere to most stains and finishes after proper preparation
and dry times. Stain, sealer and finish results may vary widely depending on the wood species,
especially on oily and resinous Exotics. ALWAYS PREPARE A SAMPLE OR TEST AREA TO
DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using accepted
industry association methods. 2. For a stained floor, make your final cut with 80-100 grit paper and
screen to 80-100 grit. For an unstained floor, make your final cut with 80-100 grit paper and
disc/screen to 120-150 grit. This burnishing will reduce the amount of grain raise. 3. Use a Tampico
®
Brush on a buffer and vacuum thoroughly. 4. Tack with a dry Bona Microfiber Mop or cloth to
remove dust. 5. Apply finish system.
Rev 05/11
This data sheet replaces all previous versions
page 1/2
Bona Novia
™
Finishing
Technical data sheet
THE BONA NOVIA™ FINISH SYSTEM: Apply a Bona sealer or Bona stain and 2 coats of Bona
Novia. Follow label directions. Adding a third coat of Bona Novia is recommended in heavy-traffic
commercial and residential areas. Visit www.bona.com for additional product information.
®
®
®
RECOMMENDED APPLICATORS: Bona Roller, Bona Floor Coater (T-bar), Bona Cut-In Pad.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: SHAKE WELL BEFORE USING. DO NOT THIN. DO NOT ADD
WATER. Insert supplied filter.
FINISHING: 1. Pour a 6” wide line of Bona Novia across the direction of the flooring, cut-in 12”-18”
away from wall. 2. Saturate the roller with finish. Make sure to roll over all areas where cut-in pad
was used. 3. Set roller down at back side of puddle and pull the roller towards you. Then push back
in the same path feathering past your start point. Do not apply pressure to the roller. Overlap your
run by 25%. Rolling too fast will cause drips to fly off the roller. 4. BE SURE YOU ARE USING THE
RECOMMENDED COVERAGE OF 500-600 SQ. FT. PER GALLON. DO NOT SPREAD TOO
THIN. 5. Allow the first coat to dry 2-3 hours. High humidity and/or low temperature conditions will
extend the dry time (recommended conditions of 65-80° F (18° C-27° C) 40-60% relative humidity).
®
6. For smoothest results, abrade with a Bona Conditioning Pad before applying final coat. Always
vacuum and tack thoroughly with a slightly water dampened Bona Microfiber Mop or cloth after
abrading. Allow final coat to dry at least 24 hours before use.
INTERCOAT ABRASION: It is not necessary to abrade between Bona waterborne sealer and
finish coats unless more than 48 hours has passed since the previous coat was applied. For
smoothest results, abrade between all coats. When using solvent-based sealers, ALWAYS abrade
before finish coats. Always vacuum and tack thoroughly with a slightly water-dampened Bona
Microfiber Mop or cloth after abrading. is product has a maximum VOC (Volatile Organic
®
RECOATING: Be sure floor is free from wax, polish and oily residues. Follow the Bona Prep
system, applying 1-2 coats of Bona Novia. If Recoating a Factory Prefinished Floor, DO NOT USE
®
®
Bona Novia finish. Use Bona Naturale or Bona Traffic finishes with the Bona Prep system.
Delamination can occur if the Bona Prep process is not followed; always test for compatibility.
Maintenance
CURING: The curing process takes approximately 7 days, (70% cured after 1 day, 90% after 3
days). Do not replace area rugs until the floor has fully cured. The floor may be walked on after 24
hours, but remains susceptible to scuffing or marring until completely cured. Furniture may be
placed onto floor after 72 hours (90% cured). Do not drag or slide furniture. Use only a dry Bona
Microfiber Mop or cloth for cleaning during the first week.
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container.
FLOOR CARE: Put walk-off mats at all entrance doorways to keep out excessive dirt and grit.
®
Sweep or vacuum daily and damp-wipe as needed with Bona Hardwood Floor Cleaner. Use felt
pads under furniture legs and appliances.
STORAGE: Nonflammable - Bona Novia should be stored in a climate controlled environment.
KEEP FROM FREEZING. Do not store above 100° F (38° C).
Order Information
Item #:
WT230018002
WT230318002
WT230618002
Size/Sheen
1 Gallon/Gloss
1 Gallon/Semi-Gloss
1 Gallon/Satin
Rev 05/11
This data sheet replaces all previous versions
#/Case
3
3
3
page 2/2
Bona Retarder
Coatings
Technical data sheet
Bona Retarder is designed to retard the drying/curing process of Bona waterborne finishes,
allowing for more open time in less than ideal working environments, such as very hot/dry climates.
Technical data
Physical Characteristics:
Ingredients – Water and diethylene glycol monoethyl ether.
Color – Clear
Density – 8.33 lbs./gallon (1.0 S.G.)
US Regulatory VOC – <275 g/l when used with a Bona Waterborne Finish
Odor – Non-offending
Stability – 1 year shelf life in unopened container
Packaging – 5.4 ounce plastic bottle
Recommended Use
®
®
®
Can be added to any Bona waterborne finish (Bona Naturale , Bona Traffic , Bona Traffic HD ,
®
Bona Mega , and Bona Novia™) to retard the drying/curing process.
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
MIXING INSTRUCTIONS: Add one 5.4oz. bottle of Bona Retarder to 1 gallon of Bona waterborne
finish (Bona Traffic, Bona Traffic HD, Bona Mega, Bona Novia) then shake thoroughly for 15 – 20
seconds. Once mixed, apply finish according to label instructions.
Order Information
Item #
WX100053001
Size
5.4 ounces.
Rev 05/11
This data sheet replaces all previous versions
#/Case
12
page 1/1
®
®
Bona DriFast Sealer
Finishing
Technical data sheet
A quick drying, polyurethane sanding sealer. Designed to penetrate and seal bare wood.
®
Compatible with all Bona stains, oil-modified and waterborne finishes.
Easy application
Penetrates and seals the wood
Fast drying – 1 ½ - 2 hours
Rapid hardness development
Sands easily for use as a sanding sealer
Meets ASTM D 1640 for quick-dry sealers
VOC Compliant under U.S. EPA regulations
Clean up with mineral spirits
Technical data
Physical Characteristics:
Ingredients – Mineral spirits (solvent), urethane resins, silica, driers.
Color – wet – amber; dry – light amber
Solids – 37%
Density – 7.21 lbs/gallon (0.866 S.G.)
US Regulatory VOC – 550 g/L
Odor – Mineral spirits
Stability – One year shelf life in unopened container
Flash Point – 103º F (39º C)
Packaging – 1-gallon can, 5-gallon pail
Application Characteristics:
Clarity – Clear
Leveling – Excellent
Defoaming – Excellent/complete
Drying Time – 1-1/2 - 2 hours
Application Tools – Lambswool applicator, synthetic floor coater
Coverage – 600-700 square feet per gallon
Percent Cured After 24 Hours – 60%
Maximum Cure – 2 weeks
Recommended Use
®
Formulated for use under all Bona oil-modified and waterborne finishes.
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
®
®
COMPATIBILITY STATEMENT: Bona DRIFAST Sealer is designed to penetrate and seal bare
®
wood. It is compatible with all Bona stains, oil-modified and waterborne finishes. ALWAYS
PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY IF USING ANYTHING
®
OTHER THAN A BONA PRODUCT.
PREPARATION: SANDING AND FINISHING
1. Sand and prepare floor using NOFMA-accepted methods. NOTE: It may be necessary to first
trowel-fill the entire floor, depending on the extent of cracks between strip and parquet flooring.
2. Make your final cut with 80-grit paper and screen to 80-100-grit screen. 3. Vacuum thoroughly.
4. Tack with dry microfiber mop. 5. Apply sealer and finish system (see finish directions).
APPLICATION: STIR WELL BEFORE USING!
®
1. After preparing surface, apply DRIFAST Sealer at 600-700 sq. ft. per gallon with lambswool
applicator or synthetic floor coater applicator.
2. Avoid leaving puddles of excessive amounts of sealer on the floor.
3. Allow surface to thoroughly dry (1 1/2 - 2 hours). High humidity and/or low temperature
conditions will extend the drying time while increased ventilation and airflow will reduce dry time.
®
4. Abrade surface thoroughly with a Bona Conditioning Pad or a used 120-grit screen before
finishing.
5. Vacuum thoroughly and tack with mineral spirits.
Rev 11/10
This data sheet replaces all previous versions
page 1/2
®
®
Bona DriFast Sealer
Finishing
Technical data sheet
®
6. Apply a Bona oil-modified or waterborne finish.
STORAGE AND DISPOSAL: Keep container closed when not in use. Do not transfer contents to
other containers for storage and disposal. Do not return used material to the original container;
reapply or dispose of. In case of spillage, absorb with inert material. Dispose of contaminated
absorbent, container and/or unused contents in accordance with local, state and federal
regulations.
®
DANGER: RAGS, STEEL WOOL OR WASTE SOAKED WITH DRIFAST SEALER MAY
SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED. IMMEDIATELY AFTER EACH
USE, PLACE RAGS, STEEL WOOL OR WASTE IN A SEALED, WATER-FILLED METAL
CONTAINER.
Maintenance
CLEAN-UP: Clean applicator tools and equipment with mineral spirits.
STORAGE AND DISPOSAL: Keep container closed when not in use. Do not transfer contents to
other containers for storage and disposal. Do not return used material to the original container;
reapply or dispose of. In case of spillage, absorb with inert material. Dispose of contaminated
absorbent, container and/or unused contents in accordance with local, state and federal
regulations.
Order Information
Item #:
Quart: SB750051001
1 Gallon: SB750018172
5 Gallon: SB750018173
#/Case:
Quart:
6
1 Gallon: 4
5 Gallon: 1
Rev 11/10
This data sheet replaces all previous versions
page 2/2
®
Woodline Polyurethane
Finishing
Technical data sheet
A premium, oil-modified wood floor finish formulated for interior use on residential and commercial
wood floors.
Provides a tough, protective coat
Slight amber color - enhances natural color of wood
Does not require thinning under normal environmental and application conditions (65º-75ºF, 4060% relative humidity)
Available in gloss, semi-gloss and satin
Self-leveling
Will adhere to most solvent-based stains and finishes and most waterborne finishes after proper
preparation, drying times and curing times
Technical data
Physical Characteristics:
Ingredients –
Satin and Semi-Gloss: Oil-modified polyurethane resin, mineral spirits (solvent), driers, silica
Gloss: Oil-modified polyurethane resin, mineral spirits (solvent), alkyd resin, driers
Color – Gold amber
Solids – 43.5%
Density – Gloss: 7.3 lbs/gallon (.87 S.G.); Satin and Semi-Gloss: 7.8 lbs./gallon (.94 S.G.)
US Regulatory VOC – 510 g/L
Gloss Level – Gloss: (60º) >90º; Semi-Gloss: 60; Satin: 30
Odor – Mineral spirits
Stability – One year shelf life in unopened container
Flash Point – Satin and Semi-Gloss: 103º F; 103º F (39ºC); Gloss: 110º F (43ºC)
Packaging – 5 gallon pail · 1 gallon can · 1 quart can
Application Characteristics:
Clarity – Gloss: Clear; Satin and Semi-Gloss: Slightly opaque
Coverage – 500 square feet per gallon
Percent Cured After 24 Hours – 40%
Maximum Cure – 100% after 2 weeks
®
Application Tools – Bona Brush, lambswool applicator
Leveling – Good
Defoaming – Excellent
Drying Time – 8-12 hours
Recommended Use
Residential
Commercial
Not recommended over white or pastel stains
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
®
COMPATIBILITY: BONA WOODLINE POLYURETHANE is not recommended over shellac,
lacquer sanding sealers, fillers or stains containing stearates. Polyurethane finishes will have a
slight ambering effect over light colored surfaces. Bona Woodline Poly will adhere to most stains
and finishes after proper preparation and dry times. Stain, sealer and finish results may vary widely
depending on the wood species, especially on oily and resinous Exotics. ALWAYS PREPARE A
SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED
RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using accepted
industry association methods. 2. For a stained floor, make your final cut with 80-100 grit paper and
screen to 80-100 grit. For an unstained floor, make your final cut with 80-100 grit paper and
disc/screen to 120-150 grit. This burnishing will reduce the amount of grain raise. 3. Use a Tampico
Brush on a buffer and vacuum thoroughly. 4. Tack with a dry Bona® Microfiber Mop or cloth to
remove dust. 5. Apply finish system.
®
THE BONA WOODLINE POLY SYSTEM: Bona Woodline Poly is a 3-coat system. For an
®
®
unstained floor, apply 1 coat of Bona Drifast Sealer according to label directions, followed by 2
®
®
coats of Bona Woodline Poly. For a stained floor, apply a Bona Drifast Stain according to label
Rev 11/10
This data sheet replaces all previous versions
page 1/2
®
Woodline Polyurethane
Finishing
Technical data sheet
directions, followed by 2 coats of Bona Woodline Poly. Adding a third coat of Bona Woodline Poly
is recommended in heavy-traffic commercial and residential areas. Visit www.bona.com for
additional product information.
RECOMMENDED APPLICATORS: Lambswool applicator, natural bristle brush, snowplow tool,
flocked foam paint pad and roller. NOTE: Use a clean applicator for sealer and a separate clean
applicator for finish.
MIXING INSTRUCTIONS: STIR WELL BEFORE USE. DO NOT THIN.
FINISHING: 1. Apply Bona Woodline Poly going with the grain of the wood. 2. Be sure to feather
out each stroke to avoid applicator marks. 3. BE SURE YOU ARE USING THE RECOMMENDED
COVERAGE OF 500 SQ FT PER GALLON. 4. Allow each coat to dry thoroughly (approximately 812 hours). High humidity and/or low temperature conditions will extend dry time while increased
ventilation and airflow will reduce dry time (recommended conditions of 65-80°F (18°C-27° C)/ 4060% relative humidity). 5. Abrade in-between all coats with a 120 – 150 grit screen or maroon
pad. 6. Thoroughly vacuum and wipe with a clean, lint-free, water dampened cloth between coats
of finish. If desired, a third coat may be applied. Allow final coat to dry a minimum of 24 hours
before use and avoid heavy traffic for 72 hours.
®
RECOATING: Be sure floor is free from wax, polish and oily residues. Follow the Bona Prep
system, applying 1-2 coats of Bona Woodline Poly. If Recoating a Factory Prefinished Floor, DO
®
®
NOT USE Bona Woodline Poly. Use Bona Naturale or Bona Traffic finishes with the Bona Prep
system. Delamination can occur if the Bona Prep process is not followed and the floor has not
been tested for compatibility.
DANGER: RAGS, STEEL WOOL OR WASTE SOAKED WITH BONA WOODLINE
POLYURETHANE MAY SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED.
IMMEDIATELY AFTER EACH USE, PLACE RAGS, STEEL WOOL OR WASTE IN A SEALED,
WATER-FILLED, METAL CONTAINER.
Maintenance
CURING: The curing process takes approximately 14 days. The floor may be walked on after 24
hours, but the floor is susceptible to scuffing or marring prior to completion of the curing time.
Do not replace walk-off mats until finish is fully cured. Furniture may be placed onto floor after 72
hours (90% cured). Do not drag or slide furniture. Do not clean with water or detergent during the
curing process. Use only a dry cloth for cleaning during the first two weeks.
CLEAN-UP: Clean application tools and equipment with mineral spirits.
®
FLOOR CARE: Maintain your hardwood floor with Bona Professional Series floor care products.
STORAGE AND DISPOSAL: Store at room temperature. Keep container closed when not in use.
Do not store above 100° F (38° C). Do not transfer contents to other containers for storage and
disposal. In case of spillage, absorb with inert material. Dispose of contaminated absorbent,
container and unused contents in accordance with local, state and federal regulations.
Order Information
Item#
ST750051058
ST750351064
ST750651061
ST750018059
ST750318065
ST750618062
ST750055060
ST750355066
ST750655063
Size / Sheen
Quart – Gloss
Quart – Semi-Gloss
Quart – Satin
Gallon – Gloss
Gallon – Semi-Gloss
Gallon – Satin
5 Gallon – Gloss
5 Gallon – Semi-Gloss
5 Gallon – Satin
Rev 11/10
This data sheet replaces all previous versions
#/Case
6
6
6
4
4
4
1
1
1
page 2/2
®
Woodline 350 Polyurethane
Technical data sheet
A premium, low VOC oil-modified wood floor finish for interior use on residential and commercial
wood floors.
Provides a tough, protective coat
Slight amber color – enhances natural color of wood
Does not require thinning under normal environmental and application conditions (65º-80ºF, 4060% relative humidity)
Available in gloss, semi-gloss and satin
Self-leveling
Adheres to most solvent-based stains and finishes and most waterborne finishes after proper
preparation, drying times and curing times
Easy to apply
Low odor formula
VOC compliant in most areas (check with your Bona distributor)
Technical data
Physical Characteristics:
Ingredients –
Satin and Semi-Gloss: Oil-modified polyurethane resin, mineral spirits (solvent), exempt solvent,
vegetable oil, silica, driers.
Gloss: Oil-modified polyurethane resin, mineral spirits (solvent), exempt solvent, vegetable oil,
driers.
Color – Gold amber
Solids – 53.0%
Density – Gloss: 7.6 lbs./gallon (.91 S.G.); Satin and Semi-Gloss: 7.8 lbs./gallon (.94 S.G)
US Regulatory VOC – 350 g/L
Gloss Level – Gloss: (60º) >90; Semi-Gloss: 60; Satin: 40
Odor – Mineral spirits
Stability – One year shelf life in unopened container
Flash Point - 104º F (40º C)
Packaging – 1 gallon can
Application Characteristics:
Clarity – Gloss: Clear; Satin and Semi-Gloss: Slightly opaque
Coverage – 550-600 square feet per gallon
Leveling – Good
Defoaming – Excellent
Drying Time – 18-24 hours
Coverage – 550-600 square feet per gallon
Percent Cured After 24 Hours – 40%
Maximum Cure – 100% after 2 weeks
®
Application Tools – Heavyweight T-bar, Bona Brush, lambswool applicator
Recommended Use
Residential
Commercial
Not recommended over white or pastel stains
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
®
COMPATIBILITY: BONA WOODLINE 350 POLYURETHANE is not recommended over shellac,
lacquer sanding sealers, fillers or stains containing stearates. Polyurethane finishes will have a
slight ambering effect over light colored surfaces. Bona Woodline 350 Poly will adhere to most
stains and finishes after proper preparation and dry times. Stain, sealer and finish results may vary
widely depending on the wood species, especially on oily and resinous Exotics. ALWAYS
PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY, APPEARANCE AND
DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using accepted
industry association methods. 2. For a stained floor, make your final cut with 80-100 grit paper and
screen to 80-100 grit. For an unstained floor, make your final cut with 80-100 grit paper and
disc/screen to 120-150 grit. This burnishing will reduce the amount of grain raise. 3. Use a Tampico
Rev 11/10
This data sheet replaces all previous versions
page 1/2
Finishing
®
Woodline 350 Polyurethane
Finishing
Technical data sheet
®
Brush on a buffer and vacuum thoroughly. 4. Tack with a dry Bona Microfiber Mop or cloth to
remove dust. 5. Apply finish system.
®
THE BONA WOODLINE 350 POLY SYSTEM: Bona Woodline 350 Poly is a 3-coat system. For
®
®
an unstained floor, apply 1 coat of Bona Drifast Sealer according to label directions, followed by
®
®
2 coats of Bona Woodline 350 Poly. For a stained floor, apply a Bona Drifast Stain according to
label directions, followed by 2 coats of Bona Woodline 350 Poly. Adding a third coat of Bona
Woodline 350 Poly is recommended in heavy-traffic commercial and residential areas. Visit
www.bona.com for additional product information.
RECOMMENDED APPLICATORS: Lambswool applicator, natural bristle brush, snowplow tool,
flocked foam paint pad and roller.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: STIR WELL BEFORE USE. DO NOT THIN.
FINISHING: 1. Apply Bona Woodline 350 Poly going with the grain of the wood. 2. Be sure to
feather out each stroke to avoid applicator marks. 3. BE SURE YOU ARE USING THE
RECOMMENDED COVERAGE OF 500 SQ FT PER GALLON. 4. Allow each coat to dry
thoroughly (approximately 8-12 hours). High humidity and/or low temperature conditions will extend
dry time while increased ventilation and airflow will reduce dry time (recommended conditions of
65-80°F (18°C-27° C)/ 40-60% relative humidity). 5. Abrade in-between all coats with a 120 – 150
grit screen or maroon pad. 6. Thoroughly vacuum and wipe with a clean, lint-free, water dampened
cloth between coats of finish. If desired, a third coat may be applied. Allow final coat to dry a
minimum of 24 hours before use and avoid heavy traffic for 72 hours.
®
RECOATING: Be sure floor is free from wax, polish and oily residues. Follow the Bona Prep
system, applying 1-2 coats of Bona Woodline 350 Poly. If Recoating a Factory Prefinished Floor,
®
®
DO NOT USE Bona Woodline 350 Poly. Use Bona Naturale or Bona Traffic finishes with the
Bona Prep system. Delamination can occur if the Bona Prep process is not followed and the floor
has not been tested for compatibility.
DANGER: RAGS, STEEL WOOL OR WASTE SOAKED WITH BONA WOODLINE
POLYURETHANE MAY SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED.
IMMEDIATELY AFTER EACH USE, PLACE RAGS, STEEL WOOL OR WASTE IN A SEALED,
WATER-FILLED, METAL CONTAINER.
Maintenance
CURING: The curing process takes approximately 14 days. The floor may be walked on after 24
hours, but the floor is susceptible to scuffing or marring prior to completion of the curing time.
Furniture may be placed onto floor after 72 hours (90% cured). Do not drag or slide furniture. Do
not replace walk-off mats until finish is fully cured. Do not clean with water or detergent during the
curing process. Use only a dry cloth for cleaning during the first two weeks.
CLEAN-UP: Clean application tools and equipment with mineral spirits.
®
FLOOR CARE: Maintain your hardwood floor with Bona Professional Series floor care products.
STORAGE AND DISPOSAL: Store at room temperature. Keep container closed when not in use.
Do not store above 100º F (38º C). Do not transfer contents to other containers for storage and
disposal. In case of spillage, absorb with inert material. Dispose of contaminated absorbent,
container and unused contents in accordance with local, state and federal regulations.
Order Information
Item #
ST750018113
ST750318115
ST750618133
Size / Sheen
Gallon – Gloss
Gallon – Semi-Gloss
Gallon – Satin
Rev 11/10
This data sheet replaces all previous versions
#/Case
4
4
4
page 2/2
®
Bona Prep
Finishing
Technical data sheet
®
Bona Prep is a specially formulated recoat adhesion system for all types of polyurethane finished
hardwood floors, including factory prefinished floors. Bona Prep conditions and prepares the
existing finish to optimize adhesion of the new coat of finish.
Cleans and conditions existing finish to optimize adhesion of new coat of finish.
Fast – just spray and buff.
Easy – doesn’t require special training or certification.
Convenient – pre-mixed and ready to use.
Bona prep system removes scuffs and surface scratches, rather than just covering them.
®
No extra tools needed. Minimal dust with a Bona Conditioning Pad. Provides “dust free”
®
abrading when used with Bona’s DCS buffer.
Economical
Technical data
Physical Characteristics:
Ingredients – Surfactants, Dipropylene Glycol Monomethyl Ether, Ethylene Glycol Monobutyl
Ether, water, other proprietary ingredients
Color – Amber (wet)
pH – 7.0 – 8.0
Solids – <1%
Density – 8.32 lbs/gallon (1.0 S.G.)
VOC - <2%
Odor – Light antiseptic
Stability – 1 year shelf life
Packaging – 32 oz. plastic spray bottle and 1 gallon jug
Application Characteristics:
Clarity – Negligible residue (dry)
Drying Time – 15 - 20 minutes
®
Application Tools – Bona Conditioning Pad and buffer
Coverage – 2,000 sq. ft./gal. (approx).
Recommended Use
For all polyurethane-finished hardwood floors.
Aluminum oxide, ceramic, and other factory prefinished floors.
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
®
Bona Prep conditions, deep cleans and prepares the existing finish to optimize adhesion of the
new coat of finish. This product is designed to be used full-strength and packaged, DO NOT
DILUTE.
PRIOR TO USE:
Prepare a sample test area using the Bona Prep System to determine general compatibility prior
to recoating.
For factory prefinished flooring, contact the manufacturer for specific recoat recommendations.
NOTE: Do not use this product on any floor that has been waxed, polished, oiled or has been
maintained with a commercial coating.
HOW TO USE:
1. Vacuum or sweep floor thoroughly to remove loose dirt and grit.
®
2. Use Bona Prep as a spray buff solution with a standard speed (175 rpm) buffer and a Bona
Conditioning Pad. Spray Bona Prep over a large section of the floor (approximately 3’x12’) at the
rate of 2,000 square feet per gallon.
®
3. Before spray buffing the next section, remove all residues immediately, using a Bona Microfiber
Mop dampened with Bona Prep.
NOTE: overlap sections to ensure that no areas are missed.
Rev 11/10
This data sheet replaces all previous versions
page 1/2
®
Bona Prep
Finishing
Technical data sheet
®
4. Abrade the floor once it has dried using two Bona Conditioning Pads (one driving the
other).Beveled edges and any visibly unabraded areas should be cleaned and abraded by hand.
®
5. Tack the floor again to remove dust using a Bona Mop or a wrung-out cotton towel or cloth
®
dampened with Bona Prep .
6. Allow the floor to dry completely. Then apply a Bona waterborne or oil-modified finishing system
within 2 hours.
®
®
NOTE: If recoating a factory prefinished floor, use only Bona Traffic , Bona Naturale , or Bona
Strong™.
Maintenance
CLEAN-UP: Clean all tools and equipment with water.
®
STORAGE: Non-flamable – Bona Prep should be stored in a climate controlled environment.
Keep from freezing. Do not store above 100° F (38° C).
Order Information
Item #:
WM700018158
WM700051153
Size
1 Gallon
32 oz.
Rev 11/10
This data sheet replaces all previous versions
#/Case
4
8
page 2/2
Bona Remover™
Coatings
Technical data sheet
Part of the Bona Recoat System™, Bona Remover is formulated to break down contaminants
known to cause finish adhesion issues, such as acrylic polishes, waxes, oil soaps, over-spray from
furniture cleaners/dusters, and any other contaminants on a polyurethane finished wood floor or a
pre-finished wood floor. Bona Remover™ also aides in abrading the wood floor to maximize
®
adhesion of Bona Traffic .
GREENGUARD Indoor Air Quality Certified
Non-flammable
Non-toxic
hour meter
®
Technical data
Physical Characteristics:
Ingredients – Water, ethoxylated alcohol, Diethylene glycol ether, phenoxyethanol, and
Dipropylene Glycol n-butyl ether.
Color – Beige
pH – 10 - 11
Solids - 18%
Density – 9.5 lbs./gallon (1.1 S.G.)
VOC – 3%
Odor – Slight solvent
Stability – 1 year shelf life
Packaging – 1 gallon plastic bottle
Application Characteristics:
®
Application Tools – Bona Roller
Recommended Use
All types of residential and commercial polyurethane finished wood floors
Pre-finished, aluminum-oxide floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
MIXING INSTRUCTIONS: Shake product vigorously for 15-20 seconds or until all settled product is
thoroughly mixed.
APPLICATION DIRECTIONS: Prior to application, protect surrounding areas using blue tape
and/or plastic sheeting or trowels to prevent possible staining from accidental contact with Bona
Remover. In the event of a spill, immediately wipe up affected area using a clean towel and water.
1. Pour a 4” wide line of Bona Remover along starting wall. 2. Saturate the roller with product from
the pour line. Set roller down at back side of puddle and pull the roller towards you approximately
4-5 feet. Then push back in the same path beyond your original start point. BE SURE YOU ARE
USING THE RECOMMENDED COVERAGE OF 400 – 500 SQ. FT. PER GALLON. DO NOT
SPREAD TOO THIN. DO NOT COVER MORE FLOOR THAN YOU WILL BE ABLE TO ABRADE
AND RINSE IN 20-30 MINUTES (APROXIMATELY 200 SQ FT). 3. Using a 175rpm rotary buffer,
equipped with the Bona recoat abrasive drive plate, abrade the section of floor coated with Bona
Remover. Abrade with the grain up and back over the same path. Start the next pass by
overlapping the previous pass by 50%. 4. Hand-abrade any corners and sections missed by the
buffer with 120 grit paper. 5. Using a window squeegee, squeegee Bona Remover material out
from the wall. 6. Using the Bona PowerScrubber™ filled with Bona Rinse (refer to Bona Rinse
directions for mixing instructions), remove and clean all Bona Remover from floor. 7. Repeat steps
1 through 6 until entire floor has been treated. 8. TO GUARANTEE ALL CONTAMINATES HAVE
BEEN REMOVED AND MEET THE BONA RECOAT SYSTEM WARRANTY, IT IS REQUIRED
THAT THE ENTIRE FLOOR BE PREPARED A SECOND TIME FOLLOWING STEPS 1 – 7
(DURING SECOND PASS IT IS NOT NECESSARY TO HAND ABRADE). 9. Using a clean terry
towel or microfiber cloth and warm water, wipe down the perimeter of the floor, approximately 1”
out from the wall where the Bona PowerScrubber could reach. It may also be necessary to wipe
down all the baseboards and any other areas Bona Remover has come in contact with. 10.
Relocate buffer, Bona recoat abrasive drive plate, applicators and all other equipment besides the
Bona PowerScrubber from the floor. Thoroughly clean with water the Bona PowerScrubber
brushes, squeegees, power cord and your shoes/work boots of any remaining Bona Remover.
Perform a final “Rinse” step on the entire floor using the Bona PowerScrubber and Bona Rinse.
This step will help ensure the floor is clean of any Bona Remover due to foot prints or missed areas
Rev 05/11
This data sheet replaces all previous versions
page 1/2
Bona Remover™
Coatings
Technical data sheet
during the initial rinse steps. 11. Wet tack the entire floor with water. Prior to finish application feel
floor with hand, if floor feels gritty or rough in areas, you have not removed all the Bona Remover.
Repeat steps 9 & 10. 12. Allow floor to dry and following label instructions apply one coast of Bona
Traffic or Bona Traffic HD. IF A SECOND COAT OF BONA TRAFFIC IS NEEDED, INTER-COAT
ABRASION IS NOT REQUIRED UNLESS 48 HOURS OR MORE HAVE PAST. IF INTER-COAT
ABRASION IS NEEDED, ABRADE WITH A 320 GRIT MAROON PAD ONLY. THE BONA
RECOAT PROCESS TEMPORARILY WEAKENS THE FINISH SYSTEM AND AGGRESSIVE
ABRASION COULD CAUSE DAMAGE TO TOTAL FINISH SYSTEM.
Maintenance
Clean-Up: Clean all tools and equipment with warm water.
Order Information
Item #: WM800018001
#/Case: 2
Rev 05/11
This data sheet replaces all previous versions
page 2/2
Bona® Rinse™
Coatings
Technical data sheet
Part of the Bona Recoat System™, Bona Rinse is specifically designed to thoroughly clean and
rinse Bona Remover and any contaminants Bona Remover has broken down from the hardwood
floor.
GREENGUARD Indoor Air Quality Certified
Non-flammable
Non-toxic
hour meter
®
Technical data
Physical Characteristics:
Ingredients – Water, ethoxylated alcohol, Diethylene glycol ether, phenoxyethanol, and
Dipropylene Glycol n-butyl ether.
Color - Green
pH – 7-8
Solids – 0.7%
Density – 8.3 lbs./gallon (1.0 S.G.)
VOC – 3%
Odor – Slight solvent
Stability – 1 year shelf life
Packaging – 1 gallon plastic bottle
Application Characteristics:
Application Tools – Bona Power Scrubber™
Recommended Use
All types of unwaxed residential and commercial polyurethane finished wood floors
Pre-finished, aluminum-oxide floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
MIXING INSTRUCTIONS: For use with the Bona PowerScrubber™.
DO NOT USE UNDILUTTED.
ONLY USE TO RINSE BONA REMOVER.
IF USED AS A CLEANER BONA RINSE MAY DULL OR DAMAGE THE FLOOR.
Dilute Bona Rinse at a 4:1 ratio (4 parts water to 1 part concentrate). When used with the Bona
PowerScrubber, add half a gallon of concentrate to the solution tank, then add 2 gallons of water.
APPLICATION DIRECTIONS: Refer to Bona PowerScrubber™ set-up and operational
procedures. Do not allow any excess solution to pool or puddle on the wood floor. Wipe up
immediately. 1. Using the Bona PowerScrubber, clean with the grain of the wood when possible,
moving the Bona PowerScrubber up and back in the same path. Only dispense Bona Rinse agent
on the forward pass. If Bona Remover has dried or is not being removed completely it will be
necessary to dispense Bona Rinse on the backward pass or make a second pass. 2. On
subsequent passes overlap the previous pass by 20%. 3. Continue process until all Bona Remover
has been rinsed from the floor.
Maintenance
Clean-Up: Clean all tools and equipment with warm water.
Order Information
Item #: WM810018001
#/Case: 2
Rev 05/11
This data sheet replaces all previous versions
page 1/1
Bona DC Polish™
Coatings
Technical data sheet
A durable, urethane acrylic blend with an exceptionally fast dry time and no waxy build-up. Adds a
high gloss or low gloss protective layer and fills in microscratches, evening out the appearance of
the floor.
Excellent flow and leveling
Available in high gloss & low gloss
®
GREENGUARD Indoor Air Quality Certified
Fast drying – approximately 1 hour
No limited pot life and no wasted finish
Nonflammable and virtually odorless
Water clean-up
Technical data
Physical Characteristics:
Ingredients – Water, polymers, diethylene glycol monoethyl ether, and surfactants
Color – Milky white (wet)
pH – 8.0-9.0
Solids – 10% - High Gloss. 13% - Low Gloss
Density – 8.39 lbs./gallon (1.01 S.G.)
US Regulatory VOC – <1%
Gloss Level (60°) >80 for High Gloss, 30-40 Low Gloss
Odor – Non-offending
Stability – 1 year shelf life in unopened container
Packaging – 1-gallon plastic bottle
Application Characteristics:
Clarity – Clear when dry
Leveling – Excellent
Defoaming - Excellent
Drying Time – 1 hour
Coverage – 2,000 square feet per gallon
Percent Cured After 24 Hours – 90%
Maximum Cure – 100% after 72 hours
Recommended Use
Residential- kitchens, entryways, family rooms, homes with pets, children and high foot traffic
as a maintence coating.
Use every 1-3 months depending on foot traffic.
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
RECOMMENDED APPLICATORS: Bona Microfiber Applicator Pad
MIXING INSTRUCTIONS: Gently rock bottle back and forth for 30 seconds.
APPLICATION DIRECTIONS:
1. Remove all furniture, rugs, etc. from floor to be treated.
2. Dry sweep the entire floor using Bona’s microfiber dusting pad to remove any loose dirt and
debris.
3. Deep clean entire floor using the Bona Deep Clean System™. For most wood floors one or
two cleaning passes with the Bona PowerScrubber™ filled with Bona Deep Clean Solution™
will thoroughly clean the floor. For heavily soiled areas more passes may be needed to
remove ground in dirt. Upon completion of deep cleaning, damp tack(using water only) entire
floor to remove any excess cleaning solution missed by the autoscrubber.
4. Pour a 2”-3” wide line of polish going across the grain of the wood floor. Work in small
sections to avoid polish drying on the floor prior to being smoothed out.
5. Using the Bona Microfiber Applicator Pad, spread/pull the polish across the floor. Once
spread, smooth the polish out by pulling and pushing the applicator with the grain. When
Rev 01/12
This data sheet replaces all previous versions
page 1/2
Bona DC Polish™
Coatings
Technical data sheet
6.
lowering or lifting the applicator pad from the floor, do so in a gradual and gentle manner,
avoiding hard stops and starts. In most cases, the applicator pad will allow application in
corners and under toe kicks. If you cannot reach a portion of the floor, us a cut in pad or foam
brush to apply. Continue to work the floor in sections till entire floor is coated.
Be sure you are applying the polish at 2000 square feet per gallon.
For Best Results: Always test in an inconspicuous section of the floor before use. Coverage
should be 2000 square feet per bottle. Do not apply the product too thin or streaking can occur.
Coat the entire floor to ensure an even appearance.
Precautions: Do not use over any floor that has been waxed, oiled or polished. Wax, oil and polish
will prevent Bona DC Polish from adhering. Only use a clean Bona Microfiber Applicator pad to
apply Bona DC Polish. Use of contaminated applicator pads or string, cotton, or sponge mops will
cause a cloudy white appearance. Do not mix with any other products.
DRY TIMES: Allow floor to dry for 1 hour before light foot traffic. Allow 24 hours before gently
replacing furniture and normal foot traffic.
Maintenance
CURE TIME: 70% cured after 2 hours (light foot traffic), 90% cured after 24 hours (normal foot
traffic, furniture may be gently replaced), 100% fully cured after 72 hours. Do not replace carpets or
area rugs, clean floor, or expose to heavy traffic for one week.
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container
STABILITY: One year shelf life in unopened container
STORAGE: Nonflammable – Bona DC Polish should be stored in a climate controlled environment.
Keep from freezing. Do not store above 100F.
Order Information
Item #
WP510018002
WP500318002
Size
1 Ga. - High Gloss
1 Ga. - Low Gloss
Rev 01/12
This data sheet replaces all previous versions
#/Case
2
2
page 2/2
Bona Pro Series Sport &
Commercial Cleaner
Floor Care
Technical data sheet
A professional strength, non-toxic, waterborne cleaner formulated for unwaxed, polyurethane
finished wood floors. This environmentally responsible cleaner leaves no residue and will not dull
the floor’s finish.
Professional formula
Specially formulated for use on hardwood floors
Leaves no dulling residue
pH neutral
Non-flammable
Non-toxic
GREENGUARD certified for Children and Schools program
hour meter
Technical data
Physical Characteristics:
Ingredients – Water, anionic and nonionic surfactants, and glycol ether solvents
Color – Brilliant purple solution (wet)
pH – 6.0 - 8.0
Solids - 2%
Density – 8.39 lbs./gallon (1.01 S.G.)
VOC – < 3%
Odor – Non-Offending
Stability – 1 year shelf life in an unopened container
Packaging – 5 gallon pail
Application Characteristics:
Drying Time – 15-20 minutes
®
Application Tools – Bona Mop or soft cloth
Recommended Use
All types of unwaxed, sport and commercial polyurethane finished wood floors
Pre-finished, aluminum-oxide floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
Mix one part Bona hardwood floor cleaner concentrate to seven parts water.
For Regular Maintenance of Finished Floors:
1. Vacuum, sweep or dust mop
2. Mist
3. Clean. Rinse cleaning pad often to avoid streaking
Maintenance
Clean-Up: Clean all tools and equipment with warm water.
Order Information
Item #:
5 Gallon: WM700055160
Rev 11/10
This data sheet replaces all previous versions
page 1/1
™
Bona Sportive Finish
Finishing
Technical data sheet
A premium VOC compliant, two-component waterborne wood floor sport finish. Specifically
formulated for professional use on maple floors, providing a tough, high-build urethane finish.
SM
GREENGUARD Children & Schools Certified
Slightly amber
Provides excellent chemical resistance
Protects against perspiration and routine cleaning
Easy to maintain
Available in gloss
MFMA approved
Virtually odorless
Fast drying – Approximately 2-3 hours
Nonflammable
Water clean-up
Will adhere to most solvent-based and waterborne finishes after proper preparation, drying and
curing times
Technical data
Physical Characteristics:
Ingredients – Water, polymeric resin, propylene based glycol ethers and dipropylene glycol
monomethyl ether
Color – Milky, off white (wet)
pH – 7.8
Solids – 32%
Viscosity – (#4 Ford cup @ 25° C) 18.5 seconds
Density – 8.66 lbs./gallon (1.04 S.G.)
US Regulatory VOC – 200 g/L
Gloss Level – (60°) 90
Odor – Non-offending
Stability – 1 year shelf life in unopened container
Packaging – 5-gallon plastic pail · Comes complete with crosslinker
Application Characteristics:
Clarity – Clear when dry
Leveling – Excellent
Defoaming – Excellent
Drying Time – 2-3 hours
Coverage – 500-600 square feet per gallon
Percent Cured After 24 Hours – 70%; after 72 hours – 90%
Maximum Cure – 100% after 1 week
Recommended Use
Basketball courts
Volleyball courts
Racquetball, squash and badminton courts
Multi-purpose gym, stage, aerobic and dance floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET FOR THIS
PRODUCT.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
COMPATIBILITY: Bona Sportive will adhere to most stains, paints, sealers and finishes after
proper preparation and dry times. Stain, sealer, paint and finish results may vary widely depending
on the wood species, especially on oily and resinous types. ALWAYS PREPARE A SAMPLE OR
TEST AREA TO DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using MFMAaccepted methods. 2. Make your final cut with 100-120 grit paper. Screen with 100-120-grit screen.
3. Vacuum thoroughly. 4. Dry tack thoroughly. 5. Apply sealer and finish system (see finish
directions).
THE SPORTIVE FINISH SYSTEM: Bona Sportive is a 4 coat system, 1-2 coats of a Bona Sport
Sealer (follow sealer directions), CourtLines paint (if desired), and 2-3 coats of Bona Sportive.
Rev 11/10
This data sheet replaces all previous versions
page 1/2
™
Bona Sportive Finish
Finishing
Technical data sheet
RECOMMENDED APPLICATORS: Light weight T-bar with the Bona Floor Coater Sleeve.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: SHAKE OR STIR WELL BEFORE USING. Open the crosslinker bottle
and add an equal part of water to the crosslinker. Shake well. Add the crosslinker/water mixture to
the Bona Sportive within 15 minutes. Shake or stir immediately and let sit 5-10 minutes.
FINISHING: 1. Pour a 4” wide line of finish along the starting wall. 2. Using a clean, pre-dampened
applicator; draw the applicator forward, with the grain of the wood, moving the finish toward the
opposite wall. Go with the grain of the wood. 3. At the end of each run, turn the applicator towards
you and pad out the applicator parallel to the wet edge. 4. Feather out all turns. Do not push too
hard or too fast to avoid drips flying off the applicator. 5. Missed areas can be touched up if seen
right away. 6. To prevent lapping and dry marks, be sure you are using the recommended
coverage of 500-600 sq. ft. per gallon. Be careful not to spread the finish too thin. 7. Allow your first
coat to dry 2-3 hours. High humidity and/or low temperature conditions will extend the drying time
while increased ventilation and airflow will reduce dry time (recommended conditions of 65-80º F
(18-27º C), 40-60% relative humidity). Allow final coat to dry at least 48 hours before use.
INTERCOAT ABRASION FOR FLOORS WITH GAMELINES: See sealer instructions for proper
sequence of sealer, gamelines and finish coats. Before applying gamelines, abrade with Bona
Conditioning Pads or used 150 grit screens and vacuum and tack thoroughly. Note: If paint will not
be applied for 24 hours or longer, floor must be re-abraded to ensue proper adhesion. Apply
gamelines using Bona Courtlines sport floor paint. IF USING ANOTHER MANUFACTURER’S
PAINT, BEFORE APPLYING GAMELINES, ALWAYS PREPARE A SAMPLE OR TEST AREA TO
DETERMINE COMPATABILITY AND ADHESION.
INTERCOAT ABRASION FOR FLOORS WITHOUT GAMELINES: It is not necessary to abrade
between Bona waterborne sealer and finish coats unless more than 48 hours has passed since the
previous coat was applied. For smoothest results, abrade between all coats as necessary. When
using solvent-based sealers, ALWAYS abrade before finish coats. Always vacuum and tack
thoroughly with a slightly water-dampened Bona Microfiber Mop or cloth after abrading.
RECOATING: Be sure floor is free from wax, polish, and oily residues. Follow the Bona Prep®
system, applying 1-2 coats of Bona Sportive finish. Delamination can occur if the Bona Prep
process is not followed; always test for compatibility.
Maintenance
CURING: The curing process takes approximately 7 days, (70% cured after 1 day, 90% after 3
days). Do not replace area rugs until the floor has fully cured. The floor may be walked on after 24
hours, but remains susceptible to scuffing or marring until completely cured. Use only a dry Bona
Microfiber Mop or cloth for cleaning during the first week.
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container.
MAINTENANCE: Put walk-off mats at all entrance doorways to keep out excessive dirt and grit.
See Bona® Professional Series Sport and Commercial Cleaner Concentrate instructions for
cleaning and maintenance information.
STORAGE: Nonflammable – Bona Sportive should be stored in a climate-controlled environment.
KEEP FROM FREEZING. Do not store above 100º F.
Order Information
Item#
WT133055004
Size
5 Gallon
Rev 11/10
This data sheet replaces all previous versions
#/Case
1
page 2/2
™
Bona Sportive 1K Finish
Finishing
Technical data sheet
A premium VOC compliant, one-component waterborne wood floor sport finish. Specifically
formulated for professional use on maple floors, providing a tough, high-build urethane finish.
SM
GREENGUARD Children & Schools Certified
Slightly amber
Provides excellent chemical resistance
Protects against perspiration and routine cleaning
Easy to maintain
Available in gloss
MFMA approved
Virtually odorless
Fast drying – Approximately 2-3 hours
Non-flammable
Water clean-up
Will adhere to most solvent-based and waterborne finishes after proper preparation, drying and
curing times
Technical data
Physical Characteristics:
Ingredients – Water, polymeric resin, propylene based glycol ethers and dipropylene glycol
monomethyl ether
Color – Milky, off white (wet)
pH – 7.8
Solids – 32%
Viscosity – (#4 Ford cup @ 25° C) 18.5 seconds
Density – 8.66 lbs./gallon (1.04 S.G.)
US Regulatory VOC – 175 g/L
Gloss Level – (60°) 90
Odor – Non-offending
Stability – 1 year shelf life in unopened container
Packaging – 5-gallon plastic pail
Application Characteristics:
Clarity – Clear when dry
Leveling – Excellent
Defoaming – Excellent
Drying Time – 2-3 hours
Coverage – 500-600 square feet per gallon
Percent Cured After 24 Hours – 70%; after 72 hours – 90%
Maximum Cure – 100% after 1 week
Recommended Use
Basketball courts
Volleyball courts
Racquetball, squash and badminton courts
Multi-purpose gym, stage, aerobic and dance floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET FOR THIS
PRODUCT.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
COMPATIBILITY: Bona Sportive 1K will adhere to most stains, paints, sealers and finishes after
proper preparation and dry times. Stain, sealer, paint and finish results may vary widely depending
on the wood species, especially on oily and resinous types. ALWAYS PREPARE A SAMPLE OR
TEST AREA TO DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using MFMAaccepted methods. 2. Make your final cut with 100-120 grit paper. Screen with 100-120-grit screen.
3. Vacuum thoroughly. 4. Dry tack thoroughly. 5. Apply sealer and finish system (see finish
directions).
THE SPORTIVE 1K FINISH SYSTEM: Bona Sportive 1K is a 4 coat system, 1-2 coats of a Bona Sport
Sealer (follow sealer directions), CourtLines paint (if desired), and 2-3 coats of Bona Sportive 1K.
Rev 01/11
This data sheet replaces all previous versions
page 1/2
™
Bona Sportive 1K Finish
Finishing
Technical data sheet
RECOMMENDED APPLICATORS: Light weight T-bar with the Bona Floor Coater Sleeve.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: SHAKE OR STIR WELL BEFORE USING.
FINISHING: 1. Pour a 4” wide line of finish along the starting wall. 2. Using a clean, pre-dampened
applicator; draw the applicator forward, with the grain of the wood, moving the finish toward the
opposite wall. Go with the grain of the wood. 3. At the end of each run, turn the applicator towards
you and pad out the applicator parallel to the wet edge. 4. Feather out all turns. Do not push too
hard or too fast to avoid drips flying off the applicator. 5. Missed areas can be touched up if seen
right away. 6. To prevent lapping and dry marks, be sure you are using the recommended
coverage of 500-600 sq. ft. per gallon. Be careful not to spread the finish too thin. 7. Allow your first
coat to dry 2-3 hours. High humidity and/or low temperature conditions will extend the drying time
while increased ventilation and airflow will reduce dry time (recommended conditions of 65-80º F
(18-27º C), 40-60% relative humidity). Allow final coat to dry at least 48 hours before use.
INTERCOAT ABRASION FOR FLOORS WITH GAMELINES: See sealer instructions for proper
sequence of sealer, gamelines and finish coats. Before applying gamelines, abrade with Bona
Conditioning Pads or used 150 grit screens and vacuum and tack thoroughly. Note: If paint will not
be applied for 24 hours or longer, floor must be re-abraded to ensue proper adhesion. Apply
gamelines using Bona Courtlines sport floor paint. IF USING ANOTHER MANUFACTURER’S
PAINT, BEFORE APPLYING GAMELINES, ALWAYS PREPARE A SAMPLE OR TEST AREA TO
DETERMINE COMPATABILITY AND ADHESION.
INTERCOAT ABRASION FOR FLOORS WITHOUT GAMELINES: It is not necessary to abrade
between Bona waterborne sealer and finish coats unless more than 48 hours has passed since the
previous coat was applied. For smoothest results, abrade between all coats as necessary. When
using solvent-based sealers, ALWAYS abrade before finish coats. Always vacuum and tack
thoroughly with a slightly water-dampened Bona Microfiber Mop or cloth after abrading.
RECOATING: Be sure floor is free from wax, polish, and oily residues. Follow the Bona Prep®
system, applying 1-2 coats of Bona Sportive 1K finish. Delamination can occur if the Bona Prep
process is not followed; always test for compatibility.
Maintenance
CURING: The curing process takes approximately 7 days, (70% cured after 1 day, 90% after 3
days). Do not replace area rugs until the floor has fully cured. The floor may be walked on after 24
hours, but remains susceptible to scuffing or marring until completely cured. Use only a dry Bona
Microfiber Mop or cloth for cleaning during the first week.
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container.
MAINTENANCE: Put walk-off mats at all entrance doorways to keep out excessive dirt and grit.
See Bona® Professional Series Sport and Commercial Cleaner Concentrate instructions for
cleaning and maintenance information.
STORAGE: Nonflammable – Bona Sportive 1K should be stored in a climate-controlled
environment. KEEP FROM FREEZING. Do not store above 100º F.
Order Information
Item#
WT133055007
Size
5 Gallon
Rev 01/11
This data sheet replaces all previous versions
#/Case
1
page 2/2
®
Bona Sport
™
Bona SuperSport Seal
Finishing
Technical data sheet
®
Bona Sport SuperSport™ Seal is a unique product specifically designed and developed for use on
wood sport floors. SuperSport Seal’s quick-drying, non-ambering formula reduces grain raise and
prepares the floor for a protective top coat of SuperSport finish. SuperSport Seal seals the wood,
provides a high build layer with elasticity, and prevents the finish from penetrating the wood
surface. SuperSport Seal gives floors the build and depth of finish required for sport floors.
Seals the wood, preventing the finish from penetrating, keeping more finish on top of the wood.
Minimizes sidebonding
Non-yellowing
Virtually odorless
Fast drying
Nonflammable
Water clean-up
Technical data
Physical Characteristics:
Ingredients – Water, acrylic resin, Dipropylene Glycol Monomethyl Ether, defoamers.
Color – Milky, off white (wet)
pH – 7.8
Solids – 35%
Density – 8.66 lbs./gallon (1.04 S.G.)
US Regulatory VOC – 100 g/L
Gloss Level – N/A
Odor – Non-offending
Stability – 1 year shelf life in unopened container
Packaging – 5-gallon plastic pail · 1-gallon plastic bottle
Application Characteristics:
Clarity – Clear when dry
Leveling – Excellent
Defoaming – Excellent
Drying Time – 2-3 hours
®
®
®
Application Tools - Bona Brush, flocked foam Bona Swivel Head Floor Coater, Bona Swedish
Roller
Coverage – 450-550 square feet per gallon
Percent Cured After 24 Hours – N/A
Maximum Cure – 100% after 1 week
Recommended Use
Basketball courts
Volleyball courts
Racquetball and squash courts
Badminton courts
Multi-purpose gym and stage
Aerobic and dance floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
COMPATIBILITY: Stain, sealer, paint and finish results may vary widely depending on the wood
species, especially on oily and resinous types. ALWAYS PREPARE A SAMPLE OR TEST AREA
TO DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using MFMAaccepted methods. 2. Make your final cut with 100-120-grit paper. Screen with 100-120-grit screen.
3. Vacuum thoroughly. 4. Dry tack thoroughly. 5. Apply sealer and finish system (see finish
directions).
Rev 11/10
This data sheet replaces all previous versions
page 1/2
®
Bona Sport
™
Bona SuperSport Seal
Finishing
Technical data sheet
THE BONA SUPER SPORT SEAL SYSTEM: Bona Super Sport Seal is a 4 coat system: 1 coat of
Bona Super Sport Seal, 1 coat of a Bona waterborne sport floor finish, CourtLines paint (if desired),
and 2 additional Bona waterborne finish coats.
®
RECOMMENDED APPLICATORS: Light weight T-bar with the Bona Floor Coater Sleeve.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: Remove lid and stir thoroughly before using.
FINISHING: 1. Pour a 4” wide line of sealer along the starting wall. Go with the grain of the wood.
2. Using a clean, pre-dampened applicator, draw the applicator forward, with the grain of the wood,
moving the finish toward the opposite wall. Holding the applicator at a “snowplow” angle will
maintain a wet edge at all times. 3. At the end of each run, turn the applicator toward you and pad
out the applicator parallel to the wet edge. 4. Feather out all turns. If pushed too hard or too fast,
drips will fly off the applicator. 5. Missed areas can be touched up if seen right away. 6. To prevent
lapping and dry marks, be sure you are using the recommended coverage of 450-550 sq.ft.
per gallon. Be careful not to spread the finish too thin. 7. Allow Bona SUPERSPORT SEAL to dry
2-3 hours. High humidity and/or low temperature conditions will extend the drying time while
increased ventilation and airflow will reduce dry time (recommended conditions of 65-80°F (18-27°
C), 40-60% relative humidity). Apply a Bona waterborne sport floor finish.
INTERCOAT ABRASION FOR FLOORS WITH GAMELINES: Apply gamelines over the first coat
of finish. Note: DO NOT apply gamelines directly over Bona Super Sport Seal. Before applying
gamelines, abrade with Bona Conditioning Pads or used 150 grit screens and vacuum and tack
thoroughly. IF USING ANOTHER MANUFACTURER’S PAINT, BEFORE APPLYING GAMELINES,
ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATABILITY AND
ADHESION.
INTERCOAT ABRASION FOR FLOORS WITHOUT GAMELINES: It is not necessary to abrade
between Bona waterborne sealer and finish coats unless more than 48 hours has passed since the
previous coat was applied. For smoothest results, abrade between all coats as necessary. When
using solvent-based sealers, ALWAYS abrade before finish coats. Always vacuum and tack
thoroughly with a slightly water-dampened Bona Microfiber Mop or cloth after abrading.
Maintenance
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container.
STORAGE: Nonflammable - Bona Super Sport Seal should be stored in a climate controlled
environment. KEEP FROM FREEZING. Do not store above 100° F (38° C).
Order Information
Item#: WB200055091
Size: 5 Gallon
#/Case: 1
Rev 11/10
This data sheet replaces all previous versions
page 2/2
®
Bona Sport
™
SuperSport
Finishing
Technical data sheet
The top sport finish for durability and appearance. A premium two-component waterborne wood floor
finish. Specifically formulated for professional use on maple sport floors, providing a tough, high-build
urethane finish.
The most durable sport floor finish available
Non-yellowing – stays clean and clear even after several recoats
Provides excellent chemical resistance
Protects against perspiration and routine cleaning
Easy to maintain
Available in gloss
MFMA approved
Virtually odorless
Fast drying – Approximately 2-3 hours
Nonflammable
Water clean-up
Will adhere to most solvent-based and waterborne finishes and proper preparation, drying, and curing
times
Technical data
Physical Characteristics:
Ingredients – Water, polyurethane resin, N-Methyl-2-Pyrrolidone, Dipropylene Glycol Monomethyl Ether
and Dipropylene Glycol n-Butyl Ether
Color – Milky, off white (wet)
pH – 8.3
Solids – 28%
Viscosity – (#4 Ford cup @ 25° C) approx. 16 seconds
Density – 8.52 lbs./gallon (1.02 S.G.)
US Regulatory VOC – 350 g/L
Gloss Level – (60º) 88+
Odor – Non-offending
Stability – 1 year shelf life in unopened container
Packaging – 5-gallon plastic pail · Comes complete with crosslinker
Application Characteristics:
Clarity – Clear when dry
Leveling – Excellent
Defoaming – Excellent
Drying Time – 2-3 hours
Application Tools - Bona® Brush, flocked foam Bona® Swivel Head Floor Coater, Bona® Swedish Roller
Coverage – 500-600 square feet per gallon
Percent Cured After 24 Hours – 80%; after 72 hours – 90%
Maximum Cure – 100% in one week
Recommended Use
Basketball courts
Volleyball courts
Racquetball, squash and badminton courts
Multi-purpose gym, stage, aerobic and dance floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
COMPATIBILITY: Bona Super Sport will adhere to most stains, paints, sealers and finishes after proper
preparation and dry times. Stain, sealer, paint and finish results may vary widely
depending on the wood species, especially on oily and resinous types. ALWAYS PREPARE A SAMPLE
OR TEST AREA TO DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using MFMA-accepted
methods. 2. Make your final cut with 100-120-grit paper. Screen with 100-120-grit
screen. 3. Vacuum thoroughly. 4. Dry tack thoroughly. 5. Apply sealer and finish system (see finish
directions).
Rev 11/10
This data sheet replaces all previous versions
page 1/2
®
Bona Sport
™
SuperSport
Finishing
Technical data sheet
THE SUPER SPORT FINISH SYSTEM: Bona Super Sport is a 4 coat system, 1-2 coats of a Bona Sport
Sealer (follow sealer directions), CourtLines paint (if desired), and 2-3 coats of Bona Super Sport.
RECOMMENDED APPLICATORS: Light weight T-bar with the Bona® Floor Coater Sleeve.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: SHAKE OR STIR WELL BEFORE USING. Open the crosslinker bottle and
add an equal part of water to the crosslinker. Shake well. Add the crosslinker/water
mixture to Bona SUPERSPORT within 15 minutes. Shake or stir immediately and let sit 5-10 minutes.
FINISHING: 1. Pour a 4” wide line of finish along the starting wall. Go with the grain of the wood. 2. Using
a clean, pre-dampened applicator; draw the applicator forward, with the grain of the wood, moving the
finish toward the opposite wall. Holding the applicator at a “snowplow” angle will maintain a wet edge at
all times. 3. At the end of each run, turn the applicator toward you and pad out the applicator parallel to
the wet edge. 4. Feather out all turns. If pushed too hard or too fast, drips will fly off the applicator. 5.
Missed areas can be touched up if seen right away. 6. To prevent lapping and dry marks, be sure you are
using the recommended coverage of 500-600 sq.ft. per gallon. Be careful not to spread the finish too thin.
7. Allow your first coat to dry 2-3 hours. High humidity and/or low temperature conditions will extend the
drying time while increased ventilation and airflow will reduce dry time (recommended conditions of 6580°F (18-27° C), 40-60% relative humidity). Allow final coat to dry at least 48 hours before use.
INTERCOAT ABRASION FOR FLOORS WITH GAMELINES: See sealer instructions for proper
sequence of sealer, gamelines and finish coats. Before applying gamelines, abrade with Bona
Conditioning Pads or used 150 grit screens and vacuum and tack thoroughly. Note: If paint will not be
applied for 24 hours or longer, floor must be re-abraded to ensure proper adhesion.
Apply gamelines using Bona CourtLines® sport floor paint. IF USING ANOTHER
MANUFACTURER’S PAINT, BEFORE APPLYING GAMELINES, ALWAYS PREPARE A SAMPLE OR
TEST AREA TO DETERMINE COMPATABILITY AND ADHESION.
INTERCOAT ABRASION FOR FLOORS WITHOUT GAMELINES: It is not necessary to abrade between
Bona waterborne sealer and finish coats unless more than 48 hours has passed
since the previous coat was applied. For smoothest results, abrade between all coats as necessary.
When using solvent-based sealers, ALWAYS abrade before finish coats. Always
vacuum and tack thoroughly with a slightly water-dampened Bona Microfiber Mop or cloth after abrading.
RECOATING: Be sure floor is free from wax, polish and oily residues. Follow the Bona Prep™ system,
applying 1-2 coats of Bona Super Sport finish. Delamination can occur if the Bona
Prep process is not followed; always test for compatibility.
Maintenance
CURING: The curing process takes approximately 7 days, (70% cured after 1 day, 90% after 3 days). Do
not replace area rugs until the floor has fully cured. The floor may be walked on after 24 hours, but
remains susceptible to scuffing or marring until completely cured. Use only a dry Bona Microfiber Mop or
cloth for cleaning during the first week.
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container.
MAINTENANCE: Put walk-off mats at all entrance doorways to keep out excessive dirt and grit. See
Bona® Professional Series Sport and Commercial Cleaner Concentrate instructions for
cleaning and maintenance information.
STORAGE: Nonflammable - Bona Super Sport should be stored in a climate controlled environment.
KEEP FROM FREEZING. Do not store above 100° F (38° C).
Order Information
Item #: WT760055090
Size: 5 Gallon
#/Case: 1
Rev 11/10
This data sheet replaces all previous versions
page 2/2
®
Bona Sport
™
SuperSport One
Finishing
Technical data sheet
SuperSport™ is the leading one-component sport finish for durability and appearance. A premium
waterborne wood floor finish, it’s specifically formulated for professional use on maple sport floors,
providing a tough, urethane finish with good build.
Provides excellent chemical resistance
Protects against perspiration and routine cleaning
Easy to maintain
Available in gloss
MFMA approved
Virtually odorless
Fast drying – Approximately 2-3 hours
Nonflammable
Water clean-up
Will adhere to most solvent-based and waterborne finishes and proper preparation, drying, and
curing times
Slightly amber
Technical data
Physical Characteristics:
Ingredients – Water, polymeric resin, Propylene-based glycol ether, levelling and defoaming
agents.
Color – Milky white (wet)
pH – 8.0
Solids – 32.5%
Viscosity – (#4 Ford cup @ 25° C) approx. 17 seconds
Density – 8.66 lbs./gallon (1.04 S.G.)
US Regulatory VOC – 145 g/L
Odor – Non-offending
Stability – 1 year shelf life in unopened container
Packaging – 5-gallon plastic pail
Application Characteristics:
Clarity – Clear when dry
Leveling – Excellent
Defoaming – Excellent
Drying Time – 2-3 hours
®
®
®
Application Tools - Bona Brush, flocked foam Bona Swivel Head Floor Coater, Bona Swedish
Roller
Coverage – 500-600 square feet per gallon
Percent Cured After 24 Hours – 70%; after 72 hours – 90%
Maximum Cure – 100% after 1 week
Recommended Use
Basketball courts
Volleyball courts
Racquetball, squash and badminton courts
Multi-purpose gym, stage, aerobic and dance floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
COMPATIBILITY: Bona Super Sport One will adhere to most stains, paints, sealers and finishes
after proper preparation and dry times. Stain, sealer, paint and finish results may vary widely
depending on the wood species, especially on oily and resinous types. ALWAYS PREPARE A
SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED
RESULTS.
Rev 11/10
This data sheet replaces all previous versions
page 1/2
®
Bona Sport
™
SuperSport One
Finishing
Technical data sheet
SANDING AND PREPARATION OF NEW FLOORS: 1. Sand and prepare floor using MFMAaccepted methods. 2. Make your final cut with 100-120-grit paper. Screen with 100-120-grit
screen. 3. Vacuum thoroughly. 4. Dry tack thoroughly. 5. Apply sealer and finish system (see finish
directions).
THE SUPER SPORT ONE FINISH SYSTEM: Bona Super Sport One is a 4 coat system, 1-2 coats
of a Bona Sport Sealer (follow sealer directions), CourtLines paint (if desired), and 2-3
coats of Bona Super Sport One.
®
RECOMMENDED APPLICATORS: Light weight T-bar with the Bona Floor Coater Sleeve.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: Remove lid and stir thoroughly before using.
FINISHING: 1. Pour a 4” wide line of finish along the starting wall. Go with the grain of the wood. 2.
Using a clean, pre-dampened applicator; draw the applicator forward, with the grain of the wood,
moving the finish toward the opposite wall. Holding the applicator at a “snowplow” angle will
maintain a wet edge at all times. 3. At the end of each run, turn the applicator toward you and pad
out the applicator parallel to the wet edge. 4. Feather out all turns. If pushed too hard or too fast,
drips will fly off the applicator. 5. Missed areas can be touched up if seen right away. 6. To prevent
lapping and dry marks, be sure you are using the recommended coverage of 500-600 sq.ft. per
gallon. Be careful not to spread the finish too thin. 7. Allow your first coat to dry 2-3 hours. High
humidity and/or low temperature conditions will extend the drying time while increased ventilation
and airflow will reduce dry time (recommended conditions of 65-80°F (18-27° C), 40-60% relative
humidity). Allow final coat to dry at least 48 hours before use.
INTERCOAT ABRASION FOR FLOORS WITH GAMELINES: See sealer instructions for proper
sequence of sealer, gamelines and finish coats. Before applying gamelines, abrade with Bona
Conditioning Pads or used 150 grit screens and vacuum and tack thoroughly. Note: If paint will not
be applied for 24 hours or longer, floor must be re-abraded to ensure proper adhesion. Apply
®
gamelines using Bona CourtLines sport floor paint. IF USING ANOTHER MANUFACTURER’S
PAINT, BEFORE APPLYING GAMELINES, ALWAYS PREPARE A SAMPLE OR TEST AREA TO
DETERMINE COMPATABILITY AND ADHESION.
INTERCOAT ABRASION FOR FLOORS WITHOUT GAMELINES: It is not necessary to abrade
between Bona waterborne sealer and finish coats unless more than 48 hours has passed
since the previous coat was applied. For smoothest results, abrade between all coats as
necessary. When using solvent-based sealers, ALWAYS abrade before finish coats. Always
vacuum and tack thoroughly with a slightly water-dampened Bona Microfiber Mop or cloth after
abrading.
RECOATING: Be sure floor is free from wax, polish and oily residues. Follow the Bona Prep™
system, applying 1-2 coats of Bona Super Sport One finish. Delamination can occur if the
Bona Prep process is not followed; always test for compatibility.
Maintenance
CURING: The curing process takes approximately 7 days, (70% cured after 1 day, 90% after 3
days). Do not replace area rugs until the floor has fully cured. The floor may be walked on
after 24 hours, but remains susceptible to scuffing or marring until completely cured. Use only a dry
Bona Microfiber Mop or cloth for cleaning during the first week.
CLEAN-UP: Application tools should be cleaned with water and stored in an airtight container.
MAINTENANCE: Put walk-off mats at all entrance doorways to keep out excessive dirt and grit.
®
See Bona Professional Series Sport and Commercial Cleaner Concentrate instructions for
cleaning and maintenance information.
STORAGE: Nonflammable - Bona Super Sport One should be stored in a climate controlled
environment. KEEP FROM FREEZING. Do not store above 100° F (38° C).
Order Information
Item#
WT133055001
Size
5 Gallon
#/Case
1
Rev 11/10
This data sheet replaces all previous versions
page 2/2
®
Bona Sport
Sport Seal
Finishing
Technical data sheet
Oil-modified sealer for sport and all-purpose floors. For use over newly sanded sport floors. Bona
®
Sport Sport Seal meets the federal and most state clean air quality standards.
®
®
®
Formulated for use with Bona Sport Sport Poly and Bona Sport All Court Poly
Oil-modified polyurethane sport floor sealer
Seals the wood, providing a build layer and prevents the finish from penetrating
Does not require thinning under normal environmental and application conditions
For use over newly sanded sport floors
Technical data
Physical Characteristics:
Ingredients – Oil-modifed polyurethane resin, mineral spirits (solvent), driers, defoamers.
Color – Light amber
Solids – 43%
Density – 7.3 lbs./gallon (.88 S.G.)
US Regulatory VOC – 500 g/L
Viscosity – (#4 Ford cup @ 25° C) approx. 17 seconds
Odor – Mineral spirits
Stability – 1 year shelf life in unopened container
Flash Point – 110º F (42ºC)
Packaging – 5-gallon pail
Application Characteristics:
Clarity – Clear when dry
Leveling – Good
Defoaming – Good
Drying Time – 8-12 hours
Application Tools – Brush, lambswool applicator
Coverage – 500-600 square feet per gallon
Percent Cured After 24 Hours – N/A
Maximum Cure – 2 weeks
Recommended Use
Basketball courts
Volleyball courts
Racquetball, squash and badminton courts
Multi-purpose gym, stage, aerobic and dance floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND SAFETY MATERIAL DATA SHEET.
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
COMPATIBILITY: Stain, sealer, paint and finish results may vary widely depending on the wood
species, especially on oily and resinous types. ALWAYS PREPARE A SAMPLE OR TEST AREA
TO DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND FINISHING NEW FLOORS: 1. Sand and prepare floor using MFMA-accepted
methods.. 2. Make your final cut with 100-120-grit paper. Screen with 100-120-grit screen. 3.
Vacuum thoroughly. 4. Tack with mineral spirits. 5. Apply sealer and finish system (see finish
directions).
BONA SPORT SEAL SYSTEM: Bona Sport Seal is a 4 coat system. 2 coats of Bona Sport Seal,
Bona CourtLines paint (if desired) and 2 coats of a Bona Sport finish.
RECOMMENDED APPLICATORS: Heavy weight T-bar, Lambs wool applicator.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: Remove lid and stir thoroughly before using. DO NOT THIN.
Rev 03/11
This data sheet replaces all previous versions
page 1/2
®
Bona Sport
Sport Seal
Finishing
Technical data sheet
SEALING: 1. After preparing surface, apply Bona SPORT SEAL at 500-600 sq. ft. per gallon with
heavy weight T-bar. 2. Avoid leaving puddles of excessive amounts of sealer. 3. Allow to
thoroughly dry with adequate ventilation (8-12 hours). High humidity and/or low temperatures will
extend drying time; increased ventilation and air flow will reduce dry time (recommended conditions
®
of 65-80°F (18-27° C), 40-60% relative humidity). 4. Abrade surface thoroughly with Bona
Conditioning Pads or used 120-grit screens before finishing. 5. Vacuum thoroughly and tack with
®
water. 6. Apply a Bona Sport oil–modified or waterborne finish.
INTERCOAT ABRASION FOR FLOORS WITH GAMELINES: Apply gamelines over the second
®
coat of Bona Sport Sealer. Before applying gamelines, abrade with 120-grit screens and vacuum
and tack thoroughly. Note: If paint will not be applied for 24 hours or longer, floor must be re®
abraded to ensure proper adhesion. Apply gamelines using Bona CourtLines sport floor paint. IF
USING ANOTHER MANUFACTURER’S PAINT, BEFORE APPLYING GAMELINES, ALWAYS
PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY AND ADHESION.
®
®
After applying gamelines using CourtLines paint, once per day, abrade entire floor with Bona
Conditioning Pads or used 120 or 150 grit screens. Always vacuum and tack thoroughly after
abrading. Apply finish coat within 24 hours.
INTERCOAT ABRASION FOR FLOORS WITHOUT GAMELINES: Abrade between all sealer and
finish coats using Bona Conditioning Pads or 120 to 150 grit screens to ensure adhesion. Always
vacuum and tack thoroughly after abrading.
DANGER: RAGS, STEEL WOOL OR WASTE SOAKED WITH SPORT SEAL MAY
SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED. IMMEDIATELY AFTER EACH
USE, PLACE RAGS, STEEL WOOL OR WASTE IN A SEALED, WATER-FILLED METAL
CONTAINER.
Maintenance
CLEAN-UP: Clean application tools and equipment with mineral spirits.
STORAGE AND DISPOSAL: Store at room temperature. Keep container closed when not in use.
Do not store above 100° F (38° C). Do not transfer contents to other containers for storage and
disposal. In case of spillage, absorb with inert material. Dispose of contaminated absorbent,
container and unused contents in accordance with local, state and federal regulations.
Order Information
Item#
SB750055109
Size
5 Gallon
Rev 03/11
This data sheet replaces all previous versions
#/Case
1
page 2/2
®
Bona Sport
DriFast™Sport Seal
Finishing
Technical data sheet
®
Bona Sport Drifast™ Sport Seal is a quick-drying, oil-modified sealer designed to penetrate and
®
seal bare wood. Compatible with all Bona paints and oil-modified and waterborne sport finishes.
For professional use only.
Fast drying - 1.5 - 2 hours
Penetrates and seals the wood
Easy application
Rapid hardness development for earlier access to the floor
Meets ASTM D 1640 for quick-dry sealers
Clean-up with mineral spirits
Technical data
Physical Characteristics:
Ingredients – Mineral spirits (solvent), urethane resins, silica, driers
Color – Wet – amber; Dry – light amber
Solids – 37%
Density – 7.21 lbs./gallon (.866 S.G.)
US Regulatory VOC – 550 g/L
Odor – Mineral spirits
Stability – One year shelf life in unopened container
Flash Point - 103ºF (39ºC)
Packaging – 5-gallon pail
Application Characteristics:
Clarity – Clear
Leveling – Excellent
Defoaming – Excellent/complete
Drying Time – 1-1/2 - 2 hours
Application Tools – Lambswool applicator, synthetic floor coater
Coverage – 600-700 square feet per gallon
Percent Cured After 24 Hours – 60%
Maximum Cure – 2 weeks
Recommended Use
®
Formulated for use under all Bona Sport oil-modified and waterborne sport finishes.
Basketball courts
Volleyball courts
Racquetball, squash and badminton courts
Multi-purpose gym, stage, aerobic and dance floors
Directions
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
COMPATIBILITY: Stain, sealer, paint and finish results may vary widely depending on the wood
species, especially on oily and resinous types. ALWAYS PREPARE A SAMPLE OR TEST AREA
TO DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND FINISHING NEW FLOORS: 1. Sand and prepare floor using MFMA-accepted
methods.. 2. Make your final cut with 100-120-grit paper. Screen with 100-120-grit screen. 3.
Vacuum thoroughly. 4. Tack with mineral spirits. 5. Apply sealer and finish system (see finish
directions).
BONA DRIFAST SPORT SEAL SYSTEM: Bona Drifast Sport Seal is a 4 coat system, 1 coat of
Bona Drifast Sport Seal, 1 coat of a Bona Sport finish, Bona CourtLines paint (if desired) and 2-3
coats of a Bona Sport finish.
RECOMMENDED APPLICATORS: Heavy weight T-bar, Lambs wool applicator.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: Remove lid and stir thoroughly before using. DO NOT THIN.
Rev 11/10
This data sheet replaces all previous versions
page 1/2
®
Bona Sport
DriFast™Sport Seal
Finishing
Technical data sheet
®
SEALING: 1. After preparing surface, apply Bona DRIFAST SPORT SEAL at 600-700 sq. ft. per
gallon with heavy weight T-bar. 2. Avoid leaving puddles of excessive amounts of sealer. 3. Allow
to thoroughly dry with adequate ventilation (1½ -2 hours). High humidity and/or low temperatures
will extend drying time; increased ventilation and air flow will reduce dry time (recommended
conditions of 65-80°F (18-27° C), 40-60% relative humidity). 4. Abrade surface thoroughly with
®
Bona Conditioning Pads or used 120-grit screens before finishing. 5. Vacuum thoroughly and tack
®
with water. 6. Apply a Bona Sport oil–modified or waterborne finish.
INTERCOAT ABRASION FOR FLOORS WITH GAMELINES: Apply gamelines over the first coat
of finish. NOTE: DO NOT APPLY GAMELINES DIRECTLY TO BONA DRIFAST SPORT SEAL.
Before applying gamelines, abrade with 120-grit screens and vacuum and tack thoroughly. Note: If
paint will not be applied for 24 hours or longer, floor must be re-abraded to ensure proper
®
adhesion. Apply gamelines using Bona CourtLines sport floor paint. IF USING ANOTHER
MANUFACTURER’S PAINT, BEFORE APPLYING GAMELINES, ALWAYS PREPARE A SAMPLE
OR TEST AREA TO DETERMINE COMPATIBILITY AND ADHESION. After applying gamelines
®
®
using CourtLines paint, once per day, abrade entire floor with Bona Conditioning Pads or used
120 or 150 grit screens. Always vacuum and tack thoroughly after abrading. Apply finish coat within
24 hours.
INTERCOAT ABRASION FOR FLOORS WITHOUT GAMELINES: Abrade between all sealer and
finish coats using Bona Conditioning Pads or 120 to 150 grit screens to ensure adhesion. Always
vacuum and tack thoroughly after abrading.
DANGER: RAGS, STEEL WOOL OR WASTE SOAKED WITH DRIFAST SPORT SEAL MAY
SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED. IMMEDIATELY AFTER EACH
USE, PLACE RAGS, STEEL WOOL OR WASTE IN A SEALED, WATER-FILLED METAL
CONTAINER.
Maintenance
CLEAN-UP: Clean application tools and equipment with mineral spirits.
STORAGE AND DISPOSAL: Store at room temperature. Keep container closed when not in use.
Do not store above 100° F (38° C). Do not transfer contents to other containers for storage and
disposal. In case of spillage, absorb with inert material. Dispose of contaminated absorbent,
container and unused contents in accordance with local, state and federal regulations.
Order Information
Item#
SB750055112
Size
5 Gallons
Rev 11/10
This data sheet replaces all previous versions
#/Case
1
page 2/2
®
Bona Sport
®
All Court Polyurethane
Finishing
Technical data sheet
®
Bona All Court Polyurethane is a premium quality, oil-modified polyurethane developed
®
specifically for the wood sport floor industry. All Court provides an extremely tough, high build
gloss finish with superior flow and leveling.
Provides a tough protective coat
Provides excellent chemical resistance
Superior flow and leveling
Protects against perspiration and routine cleaning
Light amber color enhances natural color of wood
MFMA approved
Easy to maintain
Available in gloss
Will adhere to most solvent-based and waterborne finishes after proper preparation, drying, and
curing times
Technical data
Physical Characteristics:
Ingredients – Oil-modified polyurethane resin, mineral spirits (solvent), driers.
Color – Light amber
Solids – 43%
Viscosity – (#4 Ford cup @ 25° C) approx. 14-16 seconds
Density – 7.3 lbs./gallon (0.9 S.G.)
US Regulatory VOC – 500 g/L
Gloss Level (60º) – 90+
Odor – Mineral spirits
Stability – One year shelf life in unopened container
Flash Point - 103ºF (39ºC)
Packaging – 5-gallon pail
Application Characteristics:
Clarity – Clear when dry
Leveling – Excellent
Defoaming – Excellent
Drying Time – 8-12 hours
Application Tools – Brush, lambswool applicator
Coverage –600 square feet per gallon
Percent Cured After 24 Hours – 50%
Maximum Cure – 2 weeks
Recommended Use
Basketball courts
Volleyball courts
Racquetball, squash and badminton courts
Multi-purpose gym, stage, aerobic and dance floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
®
COMPATIBILITY: Bona All Court is not recommended over shellac, lacquer sanding sealers,
fillers or stains containing stearates. Oil modified finishes will have a slight ambering effect over
light colored surfaces. Bona All Court will adhere to most finishes after proper preparation and dry
times. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY,
APPEARANCE AND DESIRED RESULTS.
SANDING AND FINISHING NEW FLOORS: 1. Sand and prepare floor using MFMA-accepted
methods.. 2. Make your final cut with 100-120-grit paper. Screen with 100-120-grit screen. 3.
Vacuum thoroughly. 4. Tack with mineral spirits. 5. Apply sealer and finish system (see finish
directions).
Rev 11/10
This data sheet replaces all previous versions
page 1/2
®
Bona Sport
®
All Court Polyurethane
Finishing
Technical data sheet
®
THE BONA ALL COURT SYSTEM: Bona All Court is a 4-coat system, 1-2 coats of a Bona oilmodified sport sealer, CourtLines paint (if desired) and 2-3 coats of Bona All Court.
RECOMMENDED APPLICATORS: Heavy weight T-bar, Lambs wool applicator.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: Remove lid and stir thoroughly before using. DO NOT THIN.
FINISHING: 1. Apply Bona ALL COURT with a heavy weight T-bar applicator. Go with the grain of
the wood applying a thin, uniform coat. 2. BE SURE YOU ARE USING THE RECOMMENDED
COVERAGE OF 600 SQ FT PER GALLON. 3. Avoid leaving puddles of excessive amounts of
finish on the floor. 4. Allow first coat to dry thoroughly (approximately 8-12 hours). High humidity
and/or low temperature conditions will extend dry time while increased ventilation and airflow will
reduce dry time (recommended conditions of 65-80°F (18°-27° C)/40-60% relative humidity). 5. For
proper adhesion, abrade between coats of finish. Allow final coat to dry a minimum of 72 hours
before use.
INTERCOAT ABRASION FOR FLOORS WITH GAMELINES: See sealer instructions for proper
sequence of sealer, gamelines and finish coats. Before applying gamelines, abrade with 120-grit
screens and vacuum and tack thoroughly. Note: If paint will not be applied for 24 hours or longer,
®
floor must be re-abraded to ensure proper adhesion. Apply gamelines using Bona CourtLines
sport floor paint. IF USING ANOTHER MANUFACTURER’S PAINT, BEFORE APPLYING
GAMELINES, ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE OMPATIBILITY
®
AND ADHESION. After applying gamelines using CourtLines paint, once per day, abrade entire
®
floor with Bona Conditioning Pads or used 120 or 150 grit screens. Always vacuum and tack
thoroughly after abrading. Apply finish coat within 24 hours.
INTERCOAT ABRASION FOR FLOORS WITHOUT GAMELINES: Abrade between all sealer and
finish coats using Bona Conditioning Pads or 120 to 150 grit screens to ensure adhesion. Always
vacuum and tack thoroughly after abrading.
®
RECOATING: Be sure floor is free from wax, polish and oily residues. Follow the Bona Prep
system, applying 1-2 coats of Bona ALL COURT. Delamination can occur if the Bona Prep process
is not followed; always test for compatibility.
DANGER: RAGS, STEEL WOOL OR WASTE SOAKED WITH BONA ALL COURT MAY
SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED. IMMEDIATELY AFTER EACH
USE, PLACE RAGS, STEEL WOOL OR WASTE IN A SEALED, WATER-FILLED METAL
CONTAINER.
Maintenance
CURING: The curing process takes approximately 14 days. The floor may be walked on after 24
hours, but the floor is susceptible to scuffing or marring prior to completion of the curing time. Do
not replace athletic or walk-off mats until finish is fully cured. Do not clean with water or detergent
during the curing process.
CLEAN-UP: Clean application tools and equipment with mineral spirits.
MAINTENANCE: Put walk-off mats at all entrance doorways to keep out excessive dirt and grit.
®
See Bona Professional Series Sport and Commercial Cleaner Concentrate instructions for
cleaning and maintenance information.
STORAGE AND DISPOSAL: Store at room temperature. Keep container closed when not in use.
Do not store above 100° F (38° C). Do not transfer contents to other containers for storage and
disposal. In case of spillage, absorb with inert material. Dispose of contaminated absorbent,
container and unused contents in accordance with local, state and federal regulations.
Order Information
Item#
ST750055153
Size
5 Gallon
Rev 11/10
This data sheet replaces all previous versions
#/Case
1
page 2/2
®
Bona Sport
Sport Poly
Finishing
Technical data sheet
®
Bona Sport Sport Poly is a premium quality, oil-modified polyurethane developed specifically for
the wood sport floor market. Sport Poly provides an extremely tough, high build gloss finish with
®
excellent chemical resistance, protecting against perspiration and routine cleaning. Bona Sport
Sport Poly meets the federal and most state clean air quality standards.
High solids, oil-modified polyurethane
Provides a tough protective coat
Provides excellent chemical resistance
Protects against perspiration and routine cleaning
Light amber color enhances natural color of wood
MFMA approved
Easy to maintain
Available in gloss
Will adhere to most solvent-based and waterborne finishes after proper preparation, drying, and
curing times
Technical data
Physical Characteristics:
Ingredients – Oil-modified polyurethane resin, mineral spirits (solvent), driers.
Color – Light amber
Solids – 50%
Viscosity – (#4 Ford cup @ 25° C) approx. 21-24 seconds
Density – 7.5 lbs./gallon (.90 S.G.)
US Regulatory VOC – 450 g/L
Gloss Level – (60º) - 90+
Odor – Mineral spirits
Stability – One year shelf life in unopened container
Flash Point - 110ºF (40ºC)
Packaging – 5-gallon pail
Application Characteristics:
Clarity – Clear when dry
Leveling – Good
Defoaming – Excellent
Drying Time – 12-16 hours
Application Tools – Brush, lambswool applicator
Coverage – 600 square feet per gallon
Percent Cured After 24 Hours – 50%
Maximum Cure – 2 weeks
Recommended Use
Basketball courts
Volleyball courts
Racquetball, squash and badminton courts
Multi-purpose gym, stage, aerobic and dance floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
®
COMPATIBILITY: Bona Sport Poly is not recommended over shellac, lacquer sanding sealers,
fillers or stains containing stearates. Oil modified finishes will have a slight ambering effect over
light colored surfaces. Bona Sport Poly will adhere to most finishes after proper preparation and
dry times. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY,
APPEARANCE AND DESIRED RESULTS.
SANDING AND FINISHING NEW FLOORS: 1. Sand and prepare floor using MFMA-accepted
methods. 2. Make your final cut with 100-120-grit paper. Screen with 100-120-grit screen. 3.
Rev 11/10
This data sheet replaces all previous versions
page 1/2
®
Bona Sport
Sport Poly
Finishing
Technical data sheet
Vacuum thoroughly. 4. Tack with mineral spirits. 5. Apply sealer and finish system (see finish
directions).
®
THE BONA SPORT SPORT POLY SYSTEM: Bona Sport Poly is a 4-coat system, 1-2 coats of a
Bona oil-modified sport sealer, CourtLines paint (if desired) and 2-3 coats of Bona Sport Poly.
RECOMMENDED APPLICATORS: Heavy weight T-bar, Lambs wool applicator.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: Remove lid and stir thoroughly before using. DO NOT THIN.
FINISHING: 1. Apply Bona Sport Poly with a heavy weight T-bar applicator. Go with the grain of
the wood applying a thin, uniform coat. 2. BE SURE YOU ARE USING THE RECOMMENDED
COVERAGE OF 600 SQ FT PER GALLON. 3. Avoid leaving puddles of excessive amounts of
finish on the floor. 4. Allow first coat to dry thoroughly (approximately 12-16 hours). High humidity
and/or low temperature conditions will extend dry time while increased ventilation and airflow will
reduce dry time (recommended conditions of 65-80°F (18°-27° C)/40-60% relative humidity). 5. For
proper adhesion, abrade between coats of finish. Allow final coat to dry a minimum of 72 hours
before use.
INTERCOAT ABRASION FOR FLOORS WITH GAMELINES: See sealer instructions for proper
sequence of sealer, gamelines and finish coats. Before applying gamelines, abrade with 120-grit
screens and vacuum and tack thoroughly. Note: If paint will not be applied for 24 hours or longer,
®
floor must be re-abraded to ensure proper adhesion. Apply gamelines using Bona CourtLines
sport floor paint. IF USING ANOTHER MANUFACTURER’S PAINT, BEFORE APPLYING
GAMELINES, ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE
®
COMPATIBILITY AND ADHESION. After applying gamelines using CourtLines paint, once per
®
day, abrade entire floor with Bona Conditioning Pads or used 120 or 150 grit screens. Always
vacuum and tack thoroughly after abrading. Apply finish coat within 24 hours.
INTERCOAT ABRASION FOR FLOORS WITHOUT GAMELINES: Abrade between all sealer and
finish coats using Bona Conditioning Pads or 120 to 150 grit screens to ensure adhesion. Always
vacuum and tack thoroughly after abrading.
®
RECOATING: Be sure floor is free from wax, polish and oily residues. Follow the Bona Prep
system, applying 1-2 coats of Bona Sport Poly. Delamination can occur if the Bona Prep process is
not followed; always test for compatibility.
DANGER: RAGS, STEEL WOOL OR WASTE SOAKED WITH BONA SPORT POLY MAY
SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED. IMMEDIATELY AFTER EACH
USE, PLACE RAGS, STEEL WOOL OR WASTE IN A SEALED, WATER-FILLED METAL
CONTAINER.
Maintenance
CURING: The curing process takes approximately 14 days. The floor may be walked on after 24
hours, but the floor is susceptible to scuffing or marring prior to completion of the curing time. Do
not replace athletic or walk-off mats until finish is fully cured. Do not clean with water or detergent
during the curing process.
CLEAN-UP: Clean application tools and equipment with mineral spirits.
MAINTENANCE: Put walk-off mats at all entrance doorways to keep out excessive dirt and grit.
®
See Bona Professional Series Sport and Commercial Cleaner Concentrate instructions for
cleaning and maintenance information.
STORAGE AND DISPOSAL: Store at room temperature. Keep container closed when not in use.
Do not store above 100° F (38° C). Do not transfer contents to other containers for storage and
disposal. In case of spillage, absorb with inert material. Dispose of contaminated absorbent,
container and unused contents in accordance with local, state and federal regulations.
Order Information
Item#
ST750055111
Size
5 Gallon
Rev 11/10
This data sheet replaces all previous versions
#/Case
1
page 2/2
®
Bona Sport
Sport Seal 350
Finishing
Technical data sheet
Oil-modified sealer for sport and all-purpose hardwood floors. For use over newly sanded sport
®
floors. Bona Sport Sport Seal 350 is specially formulated to meet all federal and state clean air
quality standards.
®
Formulated for use with Bona Sport Sport Poly 350
Oil-modified polyurethane sport floor sealer
Seals the wood, providing a build layer and prevents the finish from penetrating
For use over newly sanded sport floors
Technical data
Physical Characteristics:
Ingredients – Oil-modified polyurethane resin, mineral spirits (solvent), polysiloxane, driers,
defoamers
Color – Light amber
Solids – 51-54%
Viscosity – (#4 Ford cup @ 25° C) approx. 22-26 seconds
Density – 7.7 lbs./gallon (.92 S.G.)
US Regulatory VOC – 350 g/L
Odor – Mineral spirits
Stability – One year shelf life in unopened container
Flash Point - >104ºF (PMCC)
Packaging – 5-gallon pail
Application Characteristics:
Clarity – Clear when dry
Leveling – Good
Defoaming – Good
Drying Time – 18-24 hours (based on recommended coverage rate, under ideal conditions)
Application Tools – heavy weight synthetic applicator
Coverage – 600-700 square feet per gallon
Percent Cured After 24 Hours – N/A
Maximum Cure – 2 weeks
Recommended Use
Basketball courts
Volleyball courts
Racquetball, squash and badminton courts
Multi-purpose gym, stage, aerobic and dance floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
COMPATIBILITY: Stain, sealer, paint and finish results may vary widely depending on the wood
species, especially on oily and resinous types. ALWAYS PREPARE A SAMPLE OR TEST AREA
TO DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND FINISHING NEW FLOORS: 1. Sand and prepare floor using MFMA-accepted
methods. 2. Make your final cut with 100-120-grit paper. Screen with 100-120-grit screen.
3. Vacuum thoroughly. 4. Tack with mineral spirits. 5. Apply sealer and finish system (see finish
directions).
BONA SPORT SEAL 350 SYSTEM: Bona Sport Seal 350 is a 3 or 4 coat system. 1 or 2 coats of
Bona Sport Seal 350, Bona CourtLines paint (if desired) and 2 coats of a Bona Sport finish.
RECOMMENDED APPLICATORS: Heavy weight T-bar, Lambs wool applicator.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: Remove lid and stir thoroughly before using. DO NOT THIN.
Rev 03/11
This data sheet replaces all previous versions
page 1/2
®
Bona Sport
Sport Seal 350
Finishing
Technical data sheet
SEALING: 1. After preparing surface, apply Bona SPORT SEAL 350 at 600-700 sq. ft. per gallon
with heavy weight T-bar. 2. Avoid leaving puddles of excessive amounts of sealer. 3. Allow to
thoroughly dry with adequate ventilation (18-24 hours). High humidity and/or low temperatures will
extend drying time; increased ventilation and air flow will reduce dry time (recommended
conditions of 65-80°F (18-27° C), 40-60% relative humidity). 4. Abrade surface thoroughly with
Bona® Conditioning Pads or used 120-grit screens before finishing. 5. Vacuum thoroughly and
®
tack with water. 6. Apply a Bona Sport oil–modified or waterborne finish.
INTERCOAT ABRASION FOR FLOORS WITH GAMELINES: Apply gamelines over the first or
®
second coat of Bona Sport Seal 350. Before applying gamelines, abrade with 120-grit screens
and vacuum and tack thoroughly. Note: If paint will not be applied for 24 hours or longer, floor must
®
be re-abraded to ensure proper adhesion. Apply gamelines using Bona CourtLines sport floor
paint. IF USING ANOTHER MANUFACTURER’S PAINT, BEFORE APPLYING GAMELINES,
ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY AND
®
ADHESION. After applying gamelines using CourtLines paint, once per day, abrade entire floor
®
with Bona Conditioning Pads or used 120 or 150 grit screens. Always vacuum and tack thoroughly
after abrading. Apply finish coat within 24 hours.
INTERCOAT ABRASION FOR FLOORS WITHOUT GAMELINES: Abrade between all sealer and
finish coats using Bona Conditioning Pads or 120 to 150 grit screens to ensure adhesion. Always
vacuum and tack thoroughly after abrading.
DANGER: RAGS, STEEL WOOL OR WASTE SOAKED WITH SPORT SEAL 350 MAY
SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED. IMMEDIATELY AFTER EACH
USE, PLACE RAGS, STEEL WOOL OR WASTE IN A SEALED, WATER-FILLED METAL
CONTAINER.
Maintenance
CLEAN-UP: Clean application tools and equipment with mineral spirits.
STORAGE AND DISPOSAL: Store at room temperature. Keep container closed when not in use.
Do not store above 100° F (38° C). Do not transfer contents to other containers for storage and
disposal. In case of spillage, absorb with inert material. Dispose of contaminated absorbent,
container and unused contents in accordance with local, state and federal regulations.
Order Information
Item#
SB750055111
Size
5 Gallon
Rev 03/11
This data sheet replaces all previous versions
#/Case
1
page 2/2
®
Bona Sport
Sport Poly 350
Finishing
Technical data sheet
®
Bona Sport Sport Poly 350 is a premium quality, oil-modified polyurethane developed specifically
for the wood sport floor market. Sport Poly 350 is low VOC, and provides an extremely tough, high
build gloss finish with excellent chemical resistance, protecting against perspiration and routine
®
cleaning. Bona Sport Poly 350 is specially formulated to meet all federal and state clean air quality
standards.
High solids, oil-modified polyurethane
Provides a tough protective coat
Provides excellent chemical resistance
Protects against perspiration and routine cleaning
Light amber color enhances natural color of wood
MFMA approved
Easy to maintain
Available in gloss
Will adhere to most solvent-based and waterborne finishes after proper preparation, drying, and
curing times
Technical data
Physical Characteristics:
Ingredients – Oil-modified polyurethane resin, mineral spirits (solvent), driers.
Color – Amber
Solids – 52-55%
Viscosity – (#4 Ford cup @ 25° C) approx. 22-26 seconds
Density – 7.6 lbs./gallon (.91 S.G.)
US Regulatory VOC – 350 g/L
Gloss Level (60º) – 90+
Odor – Mineral spirits
Stability – One year shelf life in unopened container
Flash Point - 104ºF (40ºC)
Packaging – 5-gallon pail
Application Characteristics:
Clarity – Clear when dry
Leveling – Good
Defoaming – Excellent
Drying Time – 18-24 hours (based on recommended coverage rate, under ideal conditions)
Application Tools – Heavyweight synthetic applicator
Coverage – 600 square feet per gallon
Percent Cured After 24 Hours – 50%
Maximum Cure – 2 weeks
Recommended Use
Basketball courts
Volleyball courts
Racquetball, squash and badminton courts
Multi-purpose gym, stage, aerobic and dance floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
®
COMPATIBILITY: Bona Sport Poly 350 is not recommended over shellac, lacquer sanding
sealers, fillers or stains containing stearates. Oil modified finishes will have a slight ambering effect
over light colored surfaces. Bona Sport Poly 350 will adhere to most finishes after proper
preparation and dry times. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE
COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.
SANDING AND FINISHING NEW FLOORS: 1. Sand and prepare floor using MFMA-accepted
methods. 2. Make your final cut with 100-120-grit paper. Screen with 100-120-grit screen. 3.
Rev 11/10
This data sheet replaces all previous versions
page 1/2
®
Bona Sport
Sport Poly 350
Finishing
Technical data sheet
Vacuum thoroughly. 4. Tack with mineral spirits. 5. Apply sealer and finish system (see finish
directions).
THE BONA SPORT POLY 350 SYSTEM: Bona Sport Poly 350 is a 3-coat system, 1 coat of a
Bona oil-modified sport sealer, CourtLines paint (if desired) and 2 coats of Bona Sport Poly 350.
RECOMMENDED APPLICATORS: Heavy weight T-bar, Lambs wool applicator.
NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.
MIXING INSTRUCTIONS: Remove lid and stir thoroughly before using. DO NOT THIN.
FINISHING: 1. Apply Bona Sport Poly 350 with a heavy weight T-bar applicator. Go with the grain
of the wood applying a thin, uniform coat. 2. BE SURE YOU ARE USING THE RECOMMENDED
COVERAGE OF 600 SQ FT PER GALLON. 3. Avoid leaving puddles of excessive amounts of
finish on the floor. 4. Allow first coat to dry thoroughly (approximately 18-24 hours). High humidity
and/or low temperature conditions will extend dry time while increased ventilation and airflow will
reduce dry time (recommended conditions of 65-80°F (18°-27° C)/40-60% relative humidity). 5. For
proper adhesion, abrade between coats of finish. Allow final coat to dry a minimum of 72 hours
before use.
INTERCOAT ABRASION FOR FLOORS WITH GAMELINES: See sealer instructions for proper
sequence of sealer, gamelines and finish coats. Before applying gamelines, abrade with 120-grit
screens and vacuum and tack thoroughly. Note: If paint will not be applied for 24 hours or longer,
®
floor must be re-abraded to ensure proper adhesion. Apply gamelines using Bona CourtLines
sport floor paint. IF USING ANOTHER MANUFACTURER’S PAINT, BEFORE APPLYING
GAMELINES, ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE
®
COMPATIBILITY AND ADHESION. After applying gamelines using CourtLines paint, once per
®
day, abrade entire floor with Bona Conditioning Pads or used 120 or 150 grit screens. Always
vacuum and tack thoroughly after abrading. Apply finish coat within 24 hours.
INTERCOAT ABRASION FOR FLOORS WITHOUT GAMELINES: Abrade between all sealer and
finish coats using Bona Conditioning Pads or 120 to 150 grit screens to ensure adhesion. Always
vacuum and tack thoroughly after abrading.
®
RECOATING: Be sure floor is free from wax, polish and oily residues. Follow the Bona Prep
system, applying 1-2 coats of Bona Sport Poly 350. Delamination can occur if the Bona Prep
process is not followed; always test for compatibility.
DANGER: RAGS, STEEL WOOL OR WASTE SOAKED WITH BONA SPORT POLY 350 MAY
SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED. IMMEDIATELY AFTER EACH
USE, PLACE RAGS, STEEL WOOL OR WASTE IN A SEALED, WATER-FILLED METAL
CONTAINER.
Maintenance
CURING: The curing process takes approximately 14 days. The floor may be walked on after 24
hours, but the floor is susceptible to scuffing or marring prior to completion of the curing time. Do
not replace athletic or walk-off mats until finish is fully cured. Do not clean with water or detergent
during the curing process.
CLEAN-UP: Clean application tools and equipment with mineral spirits.
MAINTENANCE: Put walk-off mats at all entrance doorways to keep out excessive dirt and grit.
See Bona® Professional Series Sport and Commercial Cleaner Concentrate instructions for
cleaning and maintenance information.
STORAGE AND DISPOSAL: Store at room temperature. Keep container closed when not in use.
Do not store above 100° F (38° C). Do not transfer contents to other containers for storage and
disposal. In case of spillage, absorb with inert material. Dispose of contaminated absorbent,
container and unused contents in accordance with local, state and federal regulations.
Order Information
Item#
ST750055155
Size
5 Gallon
Rev 11/10
This data sheet replaces all previous versions
#/Case
1
page 2/2
®
Bona Sport
®
Courtlines Sport Floor Paint
Technical data sheet
®
Courtlines is a high-solids, fast-drying, solvent-based graphic arts sport paint, manufactured
specifically for use with both waterborne and oil-modified sport floor sealers and finishes. Available
®
in fifteen vibrant primary colors, all Courtlines paints are blendable to achieve an endless array of
®
custom colors. A low viscosity formula with excellent flow and levelling, Courtlines provides onecoat coverage that won’t peel off when removing tape.
Specifically formulated for sport game lines, lettering, and logos
Use with Bona waterborne or oil-modifed finishes
15 vibrant colors, blendable for an unlimited possibility of custom colors
Fast drying with 24 hour recoat
VOC compliant
Very low odor – does not contain Xylene
High solids
Low viscosity
Excellent flow and leveling
Available in quarts
Technical data
Physical Characteristics:
Ingredients – Alkyd resins, odourless mineral spirits, pigments, driers, titanium dioxide
Base Colors – Red, yellow, green, lt. blue, dark blue, orange, brown, black, white, gold, maroon,
purple, lt. beige, gray, NC blue
Odor – Non-offending low odor
Solids – Colors: 47-51%; White: 66%
Flash Point - 100º F (TCC)
Density – Colors: 7.6-7.9 lbs./gallon; White: 11.1 lbs./gallon
US Regulatory VOC – Does not exceed 490 g/L
Stability – One year shelf life in unopened container
Packaging – 1-quart cans
Application Characteristics:
Coverage – 500-600 sq. ft. per gallon (125-150 square feet per quart)
Leveling – Excellent
Drying Time – 24 hour recoat
Application Tools – Brush, roller
Recommended Use
Basketball courts
Volleyball courts
Racquetball, squash and badminton courts
Multi-purpose gym, stage, aerobic and dance floors
Directions
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
COMPATIBILITY: Bona CourtLines Paint will adhere to most finishes and sealers after proper
preparation and dry times. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE
COMPATIBILITY. Bona CourtLines paints are blendable to achieve any custom color desired.
Blending rather than tinting, maintains brightness and application characteristics.
®
THE BONA COURTLINES PAINT SYSTEM: See sealer instructions for proper sequence of
sealer, gamelines and finish coats.
RECOMMENDED APPLICATORS: 1/4” nap roller, brush
NOTE: Use separate, clean roller/brush for each color of paint.
GAMELINES APPLICATION: 1. Before application, thoroughly abrade entire floor following
sealer/finish directions. Make sure paint is applied within 24 hours of floor being abraded. Reabrade if necessary. 2. Tape gamelines according to MFMA specifications. 3. Stir paint thoroughly.
Do not thin. 4. Apply evenly with the grain of the wood, using a brush or 1/4” nap roller. Apply a thin
Rev 11/10
This data sheet replaces all previous versions
page 1/2
Finishing
®
Bona Sport
®
Courtlines Sport Floor Paint
Technical data sheet
coat of paint at a rate of 500-600 sqft/gallon (125-150 square feet per quart). More than one coat
may be needed. Apply second coat once first coat is dry to the touch (1-4 hours). 5. Allow paint to
dry 24 hours before coating with finish. Additional dry time may be needed in cooler temperatures
®
and high humidity. 6. Abrade the entire floor with Bona Conditioning Pads or a used 120 or 150
screens. 7. Sweep, vacuum and tack with water. Allow floor to dry 30 minutes prior to applying
finish. Apply finish within 24 hours of abrading. Re-abrade if necessary. Note: When working with
more than one container of the same color, intermix to ensure uniformity. When mixing “custom”
colors, mix enough paint to cover entire job to ensure uniformity.
®
DANGER: RAGS, STEEL WOOL OR WASTE SOAKED WITH COURTLINES MAY
SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED. IMMEDIATELY AFTER EACH
USE, PLACE RAGS, STEEL WOOL OR WASTE IN A SEALED, WATER-FILLED, METAL
CONTAINER.
Maintenance
CLEAN-UP: Clean application tools and equipment with mineral spirits.
STORAGE AND DISPOSAL: Store at room temperature. Keep container closed when not in use.
Do not store above 100° F (38° C). Do not transfer contents to other containers for storage and
disposal. In case of spillage, absorb with inert material. Dispose of contaminated absorbent,
container and unused contents in accordance with local, state and federal regulations.
Order Information
Item#
SC750051112
SC750051113
SC750051114
SC750051115
SC750051116
SC750051117
SC750051118
SC750051119
SC750051120
SC750051154
SC750051155
SC750051156
SC750051157
SC750051158
SC750051159
Color
Lt. Blue
Red
Green
White
Black
Orange
Dark Blue
Yellow
Brown
Purple
Gold
Maroon
Gray
Lt. Beige
N.C. Blue
Rev 11/10
This data sheet replaces all previous versions
No./Case
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Lbs./Case
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
page 2/2
Finishing
Bona® Deep Clean Solution
Floor Care
Technical data sheet
A professional strength, non-toxic, waterborne cleaner formulated for unwaxed, polyurethane
finished wood floors. This environmentally responsible cleaner leaves no residue and will not dull
the floor’s finish.
Non-foaming, commercial strength hardwood floor cleaner designed specifically for the Bona
PowerScrubber™ and autoscrubbers
Leaves no dulling residue
pH neutral
Non-flammable
Non-toxic
SM
GREENGUARD Children & Schools Certified
hour meter
Technical data
Physical Characteristics:
Ingredients – Water, Ethoxylated alcohol, Diethylene glycol n-butyl ether, and Phenoxyethanol
Color – Aquamarine
pH – 7.0 - 8.0
Solids - 1%
Density – 8.35 lbs./gallon (1.0 S.G.)
VOC - <1%
Odor – Slight solvent
Stability – 1 year shelf life
Packaging – 1 gallon plastic bottle
Application Characteristics:
Drying Time – 15-20 minutes
®
Application Tools – Bona PowerScrubber™, Autoscrubbers
Recommended Use
All types of unwaxed, residential and commercial polyurethane finished wood floors
Pre-finished, aluminum-oxide floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
MIXING INSTRUCTIONS: For use with the Bona PowerScrubber™ and other autoscrubbers.DO
NOT USE UNDILUTTED. Dilute Bona Deep Clean Solution at a 4:1 ratio (4 parts Water to 1 part
concentrate). When used with the Bona PowerScrubber, add half a gallon of concentrate to the
solution tank then add 2 gallons of water.
CLEANING DIRECTIONS: Refer to autoscrubber manufacture’s set-up and operational
procedures. Do not allow excess solution to pool or puddle on the wood floor. Wipe up
immediately. For most wood floors one or two cleaning passes with the Bona PowerScrubber will
thoroughly clean the floor. For heavily soiled areas more passes may be needed to remove ground
dirt. Wet tack entire floor to remove any drips or wet spots autoscrubber may have missed.
Maintenance
Clean-Up: Clean all tools and equipment with warm water.
Order Information
Item #: WM760018001
#/Case: 2
Rev 03/12
This data sheet replaces all previous versions
page 1/1
Bona® Pro Series Hardwood
Cleaner
Technical data sheet
A professional strength, non-toxic, waterborne cleaner formulated for unwaxed, polyurethane finished
wood floors. This environmentally responsible cleaner leaves no residue and will not dull the floor’s finish.
Professional formula
Specially formulated for use on hardwood floors
Leaves no dulling residue
pH neutral
Non-flammable
Non-toxic
GREENGUARD certified for Children and Schools program
hour meter
Technical data
Physical Characteristics:
Ingredients – Water, Glycol Ether Solvents, Non-ionic and Anionic Surfacants
Color – Light purple (wet)
pH – 7.0 - 8.0
Solids - <1%
Density – 8.34 lbs./gallon (1.0 S.G.)
VOC - <1%
Odor – Non-Offending
Stability – 1 year shelf life
Packaging – 32 oz. Spray · Gallon Refill
Application Characteristics:
Drying Time – 15-20 minutes
Application Tools – Bona® Mop or soft cloth
Recommended Use
All types of unwaxed, residential and commercial polyurethane finished wood floors
Pre-finished, aluminum-oxide floors
Also great for wood cabinets
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
For Regular Maintenance of Finished Floors:
1.
Vacuum, sweep or dust mop
2.
Mist
3.
Clean. Rinse cleaning pad often to avoid streaking
Maintenance
Clean-Up: Clean all tools and equipment with warm water.
Order Information
Item#
32 oz: WM700051187
Gallon: WM700018174
#/Case
32 oz: 8
Gallon: 4
Rev 11/10
This data sheet replaces all previous versions
page 1/1
Floor Care
Bona® Pro Series Floor Cleaner
Concentrate
Technical data sheet
A professional strength, non-toxic, waterborne cleaner formulated for unwaxed, polyurethane finished
wood floors. This environmentally responsible cleaner leaves no residue and will not dull the floor’s finish.
Professional formula
Specially formulated for use on hardwood floors
Leaves no dulling residue
pH neutral
Non-flammable
Non-toxic
GREENGUARD certified for Children and Schools program
hour meter
Technical data
Physical Characteristics:
Ingredients – Water, anionic and nonionic surfactants, and glycol ether solvents
Color – Brilliant purple solution (wet)
pH – 6.0 - 8.0
Solids - 2%
Density – 8.39 lbs./gallon (1.01 S.G.)
VOC – < 3%
Odor – Non-Offending
Stability – 1 year shelf life in an unopened container
Packaging – 4 oz. bottle · Gallon
Application Characteristics:
Drying Time – 15-20 minutes
Application Tools – Bona® Mop or soft cloth
Recommended Use
All types of unwaxed, residential and commercial polyurethane finished wood floors
Pre-finished, aluminum-oxide floors
Also great for wood cabinets
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
Mix one part Bona hardwood floor cleaner concentrate to seven parts water.
For Regular Maintenance of Finished Floors:
1.
Vacuum, sweep or dust mop
2.
Mist
3.
Clean. Rinse cleaning pad often to avoid streaking
Maintenance
Clean-Up: Clean all tools and equipment with warm water.
Order Information
Item#
4oz:
WM700049040
Gallon: WM700018176
#Case:
4oz:
24
Gallon: 4
Rev 11/10
This data sheet replaces all previous versions
page 1/1
Floor Care
Bona® Pro Series Hardwood
Refill Cartridge
Technical data sheet
Bona’s Professional Series Hardwood refill cartridge contains Bona’s professional strength, noresidue hardwood cleaner in a ready-to-use cartridge for the hardwood floor spray mop.
Safe for wood
No dulling residue
Quick and easy
®
Use with Bona Hardwood floor mop
meter
Technical data
Physical Characteristics:
Ingredients – Water, Glycol Ether Solvents, Non-ionic and Anionic Surfactants
Color – Light purple (wet)
pH – 7.0 - 8.0
Solids - <1%
Density – 8.34 lbs./gallon (1.0 S.G.)
VOC - <1%
Odor – Non-Offending
Stability – 1 year shelf life
Packaging – 28.75 oz. plastic bottle
Application Characteristics:
Drying Time – 15-20 minutes
®
Application Tools – Bona Hardwood Floor Mop
Recommended Use
All types of unwaxed, residential and commercial polyurethane finished wood floors
Pre-finished, aluminum-oxide floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
Remove cap from hardwood floor cleaner and click into place on mop.
Maintenance
Always store mop with the bottle inserted.
Order Information
Item#: WM700058005
#/Case: 8
Rev 11/10
This data sheet replaces all previous versions
page 1/1
Floor Care
Bona® Pro Series Hardwood
Floor Refresher
Technical data sheet
Professional formula refresher provides a clear, highly durable gloss to polyurethane finished wood floors
that are dull, worn, scratched, or shows signs of wear. This non-toxic, waterborne formula restores the
beauty of wood floors, leaves no build-up, and is recoatable.
Professional formula
Specially formulated for use on hardwood floors
Restores shine
Easy application
Urethane maintenance coating
Dries in one hour
Non-toxic
Recoatable with finish
GREENGUARD certified for indoor air quality
hour meter
Technical data
Physical Characteristics:
Ingredients – Water, polymeric resins, Diethylene Gylcol Monoethyl Ether
Color – Milky white (wet)
pH – 8.0
Solids – 10 - 12%
Density – 8.39 lbs./gallon (1.01 S.G.)
Gloss Level – (60º)>80
Odor – Non-Offending
Flash Point – None
Stability – 1 year shelf life
VOC – Does not exceed 2%
Packaging – 1 quart plastic bottle
Application Characteristics:
Drying Time – 1 hour
Application Tools – Bona® Microfiber Application Pad
Coverage – 500 sq. ft. per quart
Clarity – Clear when dry
Leveling – Excellent
Percent Cured After 24 hours – 90%
Defoaming – Excellent
Max. cure – 100% after 1 week
Recommended Use
All types of unwaxed, residential and commercial polyurethane finished wood floors that are dull, worn,
scratched, or show signs of wear
Can be used on most “aluminum oxide” and “ceramic” type UV finishes
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
1. Remove furniture, rugs, etc. Vacuum, sweep or dust mop, then thoroughly clean with Bona Hardwood
Floor Cleaner and the green Microfiber Cleaning Pad on your Bona Mop. Allow the floor to dry. 2. Gently
rock product back and forth to mix. Slightly dampen the cream Microfiber Applicator Pad with water and
attach to mop. Squirt product onto the floor and spread. Work in sections small enough to keep the
Applicator Pad wet. Smooth with the grain. Continue working in sections until the entire floor is finished.
Rinse Applicator Pad with water. 3. Allow to dry at least 1 hour before walking on the floor. For a glossier
look, a second coat may be applied after 2 hours. Allow 24 hours before heavy foot traffic.
Maintenance
Clean-Up: Clean all tools and equipment with warm water.
Order Information
Item#: WT760051163
#/Case: 8
Rev 8/10
This data sheet replaces all previous versions
page 1/1
Floor Care
Bona® Pro Series Hardwood
Floor Mop
Technical data sheet
The Bona Hardwood Floor Mop takes easy cleaning to the next level. This ultimate hardwood floor
mop combines Bona’s high quality, no residue professional cleaner with a durable, premium spray
mop (with washable microfiber pad). Quick and easy to use. Non-toxic and leaves no dulling
residue.
Safe for wood
No dulling residue
Quick and easy
Durable, ergonomic design
Bona Hardwood Floor Mop includes:
Premium spray mop
Micro fiber cleaning pad
28.75 oz. Professional Series hardwood floor cleaning cartridge
ur meter
Technical data
Physical Characteristics of Bona Professional Series Hardwood Cleaner:
Ingredients – Water, Glycol Ether Solvents, Non-ionic and Anionic Surfactants
Color – Light purple (wet)
pH – 7.0 - 8.0
Solids – <1%
Density – 8.34 lbs./gallon (1.0 S.G.)
VOC – <1%
Gloss Level – N/A
Odor – Non-Offending
Stability – 1 year shelf life
Packaging – 32 oz. Spray · Gallon Refill
Recommended Use
All types of unwaxed, residential and commercial polyurethane finished wood floors
Pre-finished, aluminum-oxide floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
1. Spray
2. Clean
3. Enjoy the natural beauty of your hardwood floor.
Maintenance
Clean-Up: Clean all tools and equipment with warm water.
Order Information
Item #: WM710013397
#/Case: 4
Rev 05/11
This data sheet replaces all previous versions
page 1/1
Floor Care
Bona® Pro Series 18”
Hardwood Floor Care Kit
Floor Care
Technical data sheet
This system includes everything needed for easy and safe cleaning of hardwood floors on a
professional level.
Quick connect pole & base
100% adjustable
Locking sleeve
360º dynamic swivel action
Heavy duty aluminum construction
72” telescoping pole
32 oz. Bona Professional Series Hardwood Cleaner
18” microfiber cleaning pad
18” microfiber dusting pad
our ter
Technical data
Physical Characteristics of Bona Professional Series Hardwood Cleaner:
Ingredients – Water, Glycol Ether Solvents, Non-ionic and Anionic Surfactants
Color – Light purple (wet)
pH – 7.0 - 8.0
Solids – <1%
Density – 8.34 lbs./gallon (1.0 S.G.)
VOC - <1%
Odor – Non-Offending
Stability – 1 year shelf life
Packaging – 32 oz. Spray · Gallon Refill
Recommended Use
All types of unwaxed, residential and commercial polyurethane finished wood floors
Pre-finished, aluminum-oxide floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
1. Vacuum, sweep or dust mop
2. Mist
3. Clean. Rinse cleaning pad often to avoid streaking
Order Information
Item #: WM710013367
#/Case: 4
Rev 04/11
This data sheet replaces all previous versions
page 1/1
Bona® Pro Series 15”
Hardwood Floor Care System
Technical data sheet
This system includes everything needed for easy and safe cleaning of hardwood floors on a
professional level.
4 piece pole
15” plastic base
32 oz. Bona Professional Series Hardwood Cleaner
15” microfiber cleaning pad
15” microfiber dusting pad
r ter
Technical data
Physical Characteristics of Bona Professional Series Hardwood Cleaner:
Ingredients – Water, Glycol Ether Solvents, Non-ionic and Anionic Surfactants
Color – Light purple (wet)
pH – 7.0 - 8.0
Solids – <1%
Density – 8.34 lbs./gallon (1.0 S.G.)
VOC - <1%
Odor – Non-Offending
Stability – 1 year shelf life
Packaging – 32 oz. Spray · Gallon Refill
Recommended Use
All types of unwaxed, residential and commercial polyurethane finished wood floors
Pre-finished, aluminum-oxide floors
Safe for wood
No dulling residue
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
1. Vacuum, sweep or dust mop
2. Mist
3. Clean. Rinse cleaning pad often to avoid streaking
Order Information
Item #: WM710013398
#/Case: 6
Rev 05/11
This data sheet replaces all previous versions
page 1/1
Floor Care
Bona® Professional Series
Natural Oil Floor Cleaner
Floor Care
Technical data sheet
A professional strength, non-toxic, waterborne cleaner formulated for natural penetrating oiled floors. This
environmentally responsible cleaner cleans and nourishes the floor.
Professional formula
Specially formulated for use on hardwood floors treated with a penetrating oil
pH neutral
Nonflammable
Non-toxic
GREENGUARD Children and SchoolsSM Certified
Biodegradable
hour meter
Technical data
Physical Characteristics:
Ingredients – Water, glycol ether solvents, anionic and nonionic surfactants
Color – Beige (wet)
pH – 6.0 - 8.0
Solids - <1%
Density – 8.34 lbs./gallon (1.0 S.G.)
VOC – < 1%
Odor – Non-Offending
Stability – 1 year shelf life in an unopened container
Packaging – 32oz. bottle
Application Characteristics:
Drying Time – 15-20 minutes
Application Tools – Bona® Mop or soft cloth
Recommended Use
All types of unwaxed, residential and commercial natural penetrating oiled floors. Not for use on
polyurethane treated floors, please refer to the Bona Professional Series Hardwood Floor Cleaner for
cleaning.
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
For regular maintenance of finished floors:
1.
Vacuum, sweep or dust mop
2.
Mist
3.
Clean. Rinse cleaning pad often to avoid streaking
Maintenance
Clean-Up: Clean all tools and equipment with warm water.
Order Information
Item#
32oz:
WM701151001
#/Case:
32oz:
8
Rev 03/12
This data sheet replaces all previous versions
page 1/1
Bona® Professional Series
Natural Oil Floor Cleaner
System
Floor Care
Technical data sheet
This system includes everything needed for easy and safe cleaning of natural oil treated hardwood
floors on a professional level.
4 piece pole
15” plastic base
32 oz. Bona Professional Series Natural Oil Floor Cleaner
15” microfiber cleaning pad
15” microfiber dusting pad
r ter
Technical data
Physical Characteristics of Bona Professional Series Natural Oil Floor Cleaner:
Ingredients – Water, glycol ether solvents, anionic and nonionic surfactants
Color – Beige (wet)
pH – 6.0 - 8.0
Solids - <1%
Density – 8.34 lbs./gallon (1.0 S.G.)
VOC – < 1%
Odor – Non-Offending
Stability – 1 year shelf life in an unopened container
Packaging – 32oz. bottle
Application Characteristics:
Drying Time – 15-20 minutes
®
Application Tools – Bona Mop or soft cloth
Recommended Use
All types of unwaxed, residential and commercial natural penetrating oiled floors. Not for use on
polyurethane treated floors, please refer to the Bona Professional Series Hardwood Floor
Cleaner for cleaning.
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
For regular maintenance of finished floors:
1. Vacuum, sweep or dust mop
2. Mist
3. Clean. Rinse cleaning pad often to avoid streaking
Maintenance
Clean-Up: Clean all tools and equipment with warm water.
Order Information
Item #: WM710013417
#/Case: 6
Rev 03/12
This data sheet replaces all previous versions
page 1/1
Bona® Pro Series Stone, Tile &
Laminate Floor Cleaner
Technical data sheet
A professional strength waterborne, environmentally responsible cleaner specifically formulated to clean
all laminate flooring, ceramic tile, vinyl, LVT (luxury vinyl tile) sealed marble, and sealed granite floors
without dulling the finish or leaving any residue.
Professional formula
For periodic maintenance
For spot cleaning of food spills and other stains
Leaves no oily residue
Fresh and clean scent
pH neutral
Non-flammable
Non-toxic
GREENGUARD Children & SchoolsSM Certified
hour meter
Technical data
Physical Characteristics:
Ingredients – Water, Glycol Ether Solvents, Non-ionic and Anionic Surfactants
Color – Light purple (wet)
pH – 7.0 - 8.0
Solids – <1%
Density – 8.34 lbs./gallon (1.0 S.G.)
VOC – <1%
Odor – Non-Offending
Stability – 1 year shelf life
Packaging – 32 oz. Spray · Gallon Refill
Application Characteristics:
Drying Time – 15-20 minutes
Application Tools – Bona® Mop or soft cloth
Recommended Use
All types of residential and commcercial laminate flooring, ceramic, tile, vinyl, LVT (luxury vinyl tile)
sealed marble, and sealed granite floors
Also great for sealed countertops and stainless steel surfaces.
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
1. Vacuum, sweep or dust mop
2. Mist
3. Clean. Rinse cleaning pad often to avoid streaking.
Maintenance
Clean-Up: Clean all tools and equipment with warm water.
Order Information
Item #:
32 oz: WM700051188
Gallon: WM700018175
#/Case:
32 oz: 8
Gallon: 4
Rev 01/12
This data sheet replaces all previous versions
page 1/1
Floor Care
Bona® Pro Series Stone, Tile &
Laminate Refill Cartridge
Technical data sheet
Bona’s Professional Series Stone, Tile & Laminate refill cartridge contains Bona’s professional
strength, no-residue floor cleaner in a ready-to-use cartridge for the floor spray mop.
No dulling residue
Quick and easy
®
Use with Bona Hardwood floor mop
meter
Technical data
Physical Characteristics:
Ingredients – Water, Glycol Ether Solvents, Non-ionic and Anionic Surfactants
Color – Light purple (wet)
pH – 7.0 - 8.0
Solids - <1%
Density – 8.34 lbs./gallon (1.0 S.G.)
VOC – <1%
Odor – Non-Offending
Stability – 1 year shelf life
Packaging – 28.75 oz. plastic bottle
Application Characteristics:
Drying Time – 15-20 minutes
®
Application Tools – Bona Hardwood Floor Mop
Recommended Use
All types of residential and commercial laminate flooring, ceramic, tile, vinyl, LVT (luxury vinyl
tile) sealed marble, and sealed granite floors
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
Remove cap from hardwood floor cleaner and click into place on mop.
Maintenance
Always store mop with the bottle inserted.
Order Information
Item #: WM700058006
#/Case: 8
Rev 01/12
This data sheet replaces all previous versions
page 1/1
Floor Care
Bona® Pro Series Stone, Tile &
Laminate Floor Refresher
Technical data sheet
Professional formula refresher provides a clear, highly durable gloss to all sealed hard surface flooring including:
laminate flooring, vinyl, no-wax linoleum, terrazzo, unglazed tile (ceramic, Mexical Saltillo, quarry), stone, and
sealed porous marble. Waterborne acrylic formula fortified with urethane.
Professional formula
Keeps floors looking new
Quick and easy application
Dries in one hour
Waterborne acrylic formula with urethane
Non-toxic
GREENGUARD certified for indoor air quality
hour meter
Technical data
Physical Characteristics:
Ingredients – Water, acrylic polymer, urethane, wax, Diethylene Glycol Monoethyl Ether
Color – Milky white (wet)
pH –8.0
Solids – 10% - 12%
Viscosity – (#4 Ford cup @ 25º C) 10-12 seconds
Density – 8.39 lbs./gallon (1.01 S.G.)
Packaging – 1 quart plastic bottle
Gloss Level – (60º)>85
Odor – Non-Offending
Flash Point – None
Stability – 1 year shelf life
VOC – Does not exceed 2%
Application Characteristics:
Drying Time – 1 hour
Application Tools – Bona® Microfiber Applicator Pad
Coverage – 500 sq. ft. per bottle
Clarity – Clear when dry
Leveling – Excellent
Percent Cured After 24 hours – 90%
Defoaming – Excellent
Max. Cure – 100% after 1 week
Recommended Use
Use every 2-3 months on all sealed hard surface flooring
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
1. Remove furniture, rugs, etc. Vacuum, sweep or dust mop, then thoroughly clean with Bona Stone, Tile &
Laminate Floor Cleaner and the green Microfiber Cleaning Pad on your Bona Mop. Allow the floor to dry. 2.
Gently rock product back and forth to mix. Slightly dampen the cream Microfiber Applicator Pad with water and
attach to mop. Squirt Stone, Tile & Laminate Floor Refresher onto the floor and spread. Work in sections small
enough to keep the Applicator Pad wet. Continue working in sections until the entire floor is finished. Rinse
Applicator Pad with water. 3. Allow to dry at least 1 hour before walking on the floor. For a glossier floor, a
second coat may be applied after 2 hours. Allow 24 hours before heavy traffic.
For best results: Always test in an inconspicuous section of the floor before use. Coverage should be 500
square feet per bottle. Do not apply the product too thin or streaking will occur. Coat the entire floor to ensure an
even appearance.
1. Clean
2. Squirt and Spread
3. Allow to Dry
Maintenance
Clean-Up: Clean all tools and equipment with warm water.
Order Information
Item #: WT760051164
#/Case: 8
Rev 8/10
This data sheet replaces all previous versions
page 1/1
Floor Care
Bona Pro Series Floor Care
Accessories
Technical data sheet
Professional grade microfiber cleaning, applicator, and dususting pads for use with the Bona
Professional Series Hardwood and Stone, Tile & Laminate floor care products.
Professional grade
Special microfiber material will not scratch floors
Machine washable and reusable over 300 times
Fits 15” and 18” aluminum mop base
hour meter
Order Information
18” Microfiber Cleaning Pad
Item #
AX0003436
#Case
8
18” Microfiber Applicator Pad
Item #
AX0003435
#/Case
8
18” Microfiber Dusting Pad
Item #
AX0003437
#/Case
8
15” Microfiber Cleaning Pad
Item#
AX0003439
#/Case
8
Recommended Use
For use with the Bona Professional Series Hardwood and Stone, Tile & Laminate floor care
products.
aintenance
Directions
Rev 11/10
This data sheet replaces all previous versions
page 1/1
Floor Care
Bona® Atomic 300 DCS™
Sanding
Technical data sheet
®
TM
The Bona Atomic 300 DCS combines high performance HEPA filtration and portability providing
superior dust containment for all your sanding equipment. The large non-marking wheels, compact
®
chassis, narrow profile and 120v 15amp power requirements make the Bona Atomic 300 DCS™
easy to maneuver in and out of any jobsite. Our focus on design and function deliver the
performance and efficiency you expect, and the dust containment floor owners demand.
•
•
•
•
•
•
•
•
Powered by a 120v, 15amp circuit.
300 cfm ideal for one belt machine plus one edger or buffer.
Comes standard with 125’ of non-marking, smooth bore, vacuum hose.
Sand up to 1,200 sq. ft. before emptying 30 gallon dust barrel.
Light weight and easy to transport.
Quick disconnect cyclone reservoir.
Lined with 4ml plastic bags makes it easy for one person to empty.
Single, individually tested & certified HEPA filter for high vacuum efficiency.
Technical data
Motor: 2.1 HP Tangential bypass
Power: 1560 watts
Voltage: 120v 50/60hz
Amperage: 13 amps
Water lift: 70 in
CFM: 312 CFM w 3" orifice
Peak / amps: 13 amps. 15.5 peak
Watts: 1753
Noise level: 79 DB
Stage Motor: 1 stage motor 120V
Filter: 31.19 SQFT
Efficiency Rating: 99.97% Efficient @ 0.3 Micron
Filtration: Certified HEPA rated 99.97% @ .3 micron
Wheels: Non-marking, grey
Order Information
Item#
AD0003430
Rev 03/12
This data sheet replaces all previous versions
Lbs.
180
page 1/1
Bona® Atomic 600 DCS™
Sanding
Technical data sheet
®
The Bona Atomic 600 DCS™ combines high performance HEPA filtration and flexibility to deliver
the ultimate in dust evacuation technology to your jobsite. With over 600 cfm, there is enough
power to operate the unit outside the jobsite or even docked in a trailer. The flexible power source
allows for maximum power on jobsites where 240v power can be hard to come by. Simply plug the
two 120v plugs into two separate 15amp circuits. A green indicator light lets you know the two
power cords are on separate circuits, taking the guess work out of it. Our focus on design and
function deliver the performance and efficiency you expect, and the dust containment floor owners
demand.
•
•
•
•
•
•
•
•
•
®
Comparable performance to the Bona Atomic Trailer.
®
Twice the vacuum power over the Bona Atomic 300 DCS™.
Versatile power option – run unit on 120v or 240v.
600 cfm can collect dust from two belt sanders.
Comes standard with 125’ of non-marking, smooth bore, vacuum hose.
Sand up to 1,200 sq. ft. before emptying 30 gallon dust barrel.
Quick disconnect cyclone reservoir lined with 4ml plastic bags makes it easy
for one person to empty.
Trailer docking station for safe, secure transport in any trailer.
Dual, individually tested & certified HEPA filters provide maximum vacuum efficiency.
Technical data
Motor: Dual 2.1 HP Tangential bypass
Power: 3120 watts
Voltage: Dual 120v 50/60hz input or 240v single phase 50/60hz with neutral. Cords not included.
Amperage: 120v 13 amps each input
240v 13 amps single input
Water lift: 70 in
CFM: 624
Peak / amps: 13 amps. 15.5 peak
Watts: 1753
Noise level: 79 DB
Filter: 31.19 SQFT
Efficiency Rating: 99.97% Efficient @ 0.3 Micron
Filtration: Certified HEPA rated 99.97% @ .3 micron
Wheels: Non-marking, grey
Order Information
Item#
AD0003460
Rev 03/12
This data sheet replaces all previous versions
Lbs.
290
page 1/1
®
Bona Portable DCS
Sanding
Technical data sheet
The Bona Portable DCS is the most advanced dust containment system available. By combining a
Bona exclusive two step cyclonic intake system with a hospital-grade HEPA filter, the
Portable DCS delivers the dust containment results you need and your customers will demand.
®
The Portable DCS uses a Longopac system (continuous bag), to collect the dust. This system
eliminates the need to expose the collected dust to the job site when emptying the bag. The Bona
Portable DCS is GREENGUARD certified for indoor air quality.
Extremely portable and easy to use
Complete unit weighs less than 100 pounds.
Large, non-marking, locking wheels
The clear dust collection barrel and filter guage make it easy to know when the unit is full and/or
when it is time to clean the filter
A robust dolly system, allows easy loading of the unit by one person
Flexible, non-marking, crush proof, anti-static hose equipped with positive locking adaptors are
standard
hour meter
Technical data
1800 watt vacuum motor
115 volt
14 amp
18.5 gallon dust capacity
140 CFM
132” of water lift
10 sq. ft. primary filter
16 sq. ft. HEPA secondary filter
Machine weight: 95 lbs.
Dimensions: 45.5” H x 31” L x 23” W
Item #AD0003402
Order Information
Item#
Size
Lbs.
AD0003402
45.5”Hx31”Lx23”W
95 lbs.
Rev 11/10
This data sheet replaces all previous versions
page 1/1
Bona® Power Station Plus
Sanding
Technical data sheet
®
The Bona Power Station Plus is the safe, inexpensive and convenient way to protect your
valuable floor sanding equipment from high or low-voltage power situations. Use it as a power
center to centrally connect your installation and floor sanding equipment. Use it to effectively run
your floor sanding and vacuuming equipment, and adjust the power for your 230V units if your
power supply drifts from the desired voltage range. Downtime is money out of your pocket. Your
equipment is at tremendous risk for burnout during common job site situations such as when it is
necessary to use extra long power cords; when the local utility gets hit with excessive demands for
electricity; when you are forced to draw your power from a temporary power pole on a construction
site; or when you assume a 230V source is delivering 230 volts. Play it safe and smart. With the
Bona Power Station Plus there is no guessing about the power available to you. Once you are
safely connected to your power source, the easy-to-read voltage meter will tell you how many volts
of power are going to the box. Since the Power Station Plus has multiple voltage settings it can be
easily adjusted to accommodate different jobsite power needs. You have the choice of using the
Power Station Plus as a static power center for your 230V and 115V equipment or as a
buck/booster for the 230V equipment when the circumstances dictate. Simply read the LED meter
occasionally to see if the voltage feed from your main power source has changed enough to
warrant a boost or decrease in power. The 115 volt (non-boosted) outlet offers a convenient 25
Amp power source protected internally via a circuit breaker with an external reset button (This
circuit breaker offers equipment protection from power surges). The Bona Power Station Plus
comes out of the box ready to use on a 4-wire setup. It satisfies GFI requirements on 4-wire
systems so you can go right to work on any jobsite. We have included a pigtail to allow you to hook
up to 4-wire setups quickly and conveniently. Other user-friendly features include the comfortable
carry handle, lightweight compact design, and floor protective rubber feet. The sealed windings and
durable heavy gauge steel housing make it a long lasting tool.
Digital Volt Meter
Voltage Adjustment Switch with Multiple Settings
Protective Rubber Feet
25 AMP Circuit Breaker
Two 110 outlets
Convenient Carry Handle
our meter
Technical data
Electrical Capacity: 7.2 KVA
Working Capacity: 30 AMPS via the 230 volt output receptacle; 20 AMPS via the twin outlet
receptacle (all outlets may be used simultaneously, see special instructions)
Input: (1) 4-wire, GFI, 230 volt 30 AMP twistlock
Output: (1) 230 volt 30 AMP twistlock (1) 115 volt 20 AMP duplex, straight leg receptacle
Pigtail: 230 volt 30 AMP twistlock with 10-4 cable to connect Power Station Plus to power supply
Weight: 29 lbs.
Dimensions: 5-78”W x 12-7/8”H x 5”D
Order Information
Item#
AM0002417
Lbs.
29
Rev 05/11
This data sheet replaces all previous versions
#/Case
1
page 1/1
®
Bona Belt
Sanding
Technical data sheet
The Bona Belt definitely stands out from any other belt sander, boasting a powerful motor with the
new Poly-V drive belt. This stateof-the-art feature brings even more power to the drive belt and
efficiency to the motor. Weighing in at 182.5 or 175 pounds depending on drum size, the Bona
Belt has plenty of weight to put the power where you want it—on the floor. Still, it’s easy to handle,
and separates in seconds for easy carrying. A nose weight is included to make the belt more
aggressive when additional drum pressure is desired on the first cut. The Bona Belt is also Atomic
DCS® compatible, meaning healthier working conditions for you, better finish results, and more
satisfaction from your customers. The Bona Belt comes complete with 50 feet of 10/3 yellow
nonmarking cable; quick release, high-profile waist belt, dust bag, tool kit,
1-year warranty, and owner’s manual. The Bona Belt is GREENGUARD certified for indoor air
quality.
GREENGUARD certified
Innovative compact chassis for easy manuevering
Transport wheels
Poly-V drive belt increases power and is even more efficient than normal drive belts.
Adjustable, double feather handle and lever operation
®
Atomic DCS compatible
6” height adjustable handle
Technical data
Motor (single phase) 4HP, 60Hz, 230 Volt, Thermal Overload Protection
Machine Weight 10”: 182.5 lbs.; 8”: 175 lbs.
Sanding Drum Speed: 2,300 RPM
Sanding Drum Width 8” or 10”
Abrasive Sleeve Size 7-7/8” x 29-1/2” or 9-7/8” x 29- ½”
Dimensions 37-4/5” L x 14-1/5”W x 39-1/3” H
On-Line Digital Volt Meter
30 Amp 230 Volt Twist Lock Connector
Order Information
Item#
AM000314S
AM0003150S
Size
10” Belt Sander
with Sander Travel Base
8” Belt Sander
With Sander Travel Base
Rev 11/10
This data sheet replaces all previous versions
Lbs.
187.5
175
page 1/1
Bona Edge XL
Sanding
Technical data sheet
®
The Bona Edge XL’s state-of-the-art design is engineered for performance, convenience and
durability, unequaled power, superb balance and superior dust pick-up. Sanding edges and toe
®
kicks is a hard job, but with the Bona Edge XL you can make the job easier and faster. With its
®
adjustable, ergonomic handles, the Bona Edge XL is less tiring for your hands and arms. One
unique feature of the Edge is the “open-throat” design. The drive belt is located above the sanding
disc in a separate enclosure to create unobstructed air flow in the vacuum. This unimpeded airflow
®
®
results in exceptional dust pick-up. When operated with a Bona Atomic DCS (Dust Containment
System), it is virtually dust free, meaning healthier working conditions for you, less clean-up, better
®
finish results, and more satisfaction from your customers. The Bona Edge XL is GREENGUARD
certified for indoor air quality.
GREENGUARD certified
Access toe kicks and other hard to reach places
The unique “open throat” design allows unobstructed air flow in the vacuum chamber
Cast aluminum body
Adjustable ergonomic handles
Built-in 20w halogen work light
®
Atomic DCS compatible
Non-marking urethane wheels
hour meter
Technical data
Motor (single phase) 1.8 HP, 60Hz, 115 Volt
Machine weight 32 lbs.
Sanding disc size 7”
Sanding disc speed 3,000 RPM at normal load
Combination sanding disc siafast backed or standard
Illumination 20w halogen light
Adjustable ergonomic handles
Item # AM0003135
Order Information
Item#
AM0003135
Size
7”
Rev 11/10
This data sheet replaces all previous versions
Lbs.
32
page 1/1
Bona Edge
Sanding
Technical data sheet
®
®
The Bona Edge combines all the performance and features of the Bona Edge XL, with the
ergonomics and feel of a more traditional edger. By reducing the sanding arm length, the Edge
has attained a level of smoothness and balance unmatched in the industry. The Edge also has an
industry first, built in hour meter. The hour meter will help identify when it’s time for
routine maintenance, such as changing the brushes, to insure optimal performance and trouble®
free running for years to come. With its adjustable, ergonomic handles, the Bona Edge is less
tiring for your hands and arms. One unique feature of the Edge Quick-changing discs save time
and money is the “open-throat” design. The drive belt is located above the sanding disc in a
separate enclosure to create unobstructed air flow in the vacuum. This unimpeded airflow results in
®
®
exceptional dust pick-up. When operated with a Bona Atomic DCS (Dust Containment System),
it is virtually dust free, meaning healthier working conditions for you, less clean-up,
®
better finish results, and more satisfaction from your customers. The Bona Edge is
GREENGUARD certified for indoor air quality.
GREENGUARD certified
Access toe kicks and other hard to reach places
The unique “open throat” design allows unobstructed air flow in the vacuum chamber
Cast aluminum body
Adjustable ergonomic handles
Built-in 20w halogen work light
®
Atomic DCS compatible
Non-marking urethane wheels
Built-in hour meter
hour meter
Technical data
Motor (single phase) 1.8 HP, 60Hz, 115 Volt
Machine weight 31 lbs.
Sanding disc size 7”
Sanding disc speed 3,000 RPM at normal load
Combination sanding disc siafast backed or standard
Illumination 20w halogen light
Adjustable ergonomic handles
Access toe kicks and other hard to reach places
Order Information
Item#
AM0003196
Size
7”
Rev 11/10
This data sheet replaces all previous versions
Lbs.
31
page 1/1
Bona® Mini Edge
Sanding
Technical data sheet
®
The Bona Mini Edge is a completely new edge sander from Bona. The innovative design is
engineered for top rate performance, durability, comfort, superb balance and dust pickup. If you
hate edges, thresholds and stairs, you’ll love this machine. One of the unique features of the Mini
Edge is its stair sanding support. Normally when sanding stairs, the wheels may slide off the edges
of the staircase while the edge sander continues sanding. With the Bona Mini Edge, just click the
Stair Sanding Support in place and it will be perfectly balanced. Other great features of this edger
are its adjustable ergonomic handles which are designed to be less tiring for your hands and adjust
to suit your individual working position. You’ll always have great working light with the Bona Mini
Edger as the bright halogen spotlight is tucked in neatly behind an unbreakable glass cover. Fully
protected, the work light will never get in your way or collect dust. From the performance of the belt
driven motor to the ergonomic design, the Bona Mini Edge will make hard jobs easier and take you
to places
you have never been.
GREENGUARD certified
Access toe kicks and other hard to reach places
The unique “open throat” design allows unobstructed air flow in the vacuum chamber
Cast aluminum body
Adjustable ergonomic handles
Built-in 20w halogen work light
®
Atomic DCS compatible
Non-marking urethane wheels
hour meter
Technical data
Motor (single phase) 1-3/4 HP, 60Hz, 110 Volt
Machine weight 20 lbs.
Sanding disc size 6”
Sanding disc speed 4,400 RPM at normal load
Combination sanding disc siafast backed or standard
Illumination 20w halogen light
Vibration Resistant Halogen Light
Adjustable ergonomic handles
Access toe Kicks, stairs and other hard to reach places
Order Information
Item#
AM0003148
Size
6”
Rev 11/10
This data sheet replaces all previous versions
Lbs.
20
page 1/1
Bona® FlexiSand DCS Buffer
Technical data sheet
®
The Bona FlexiSand DCS Buffer’s technologically-advanced design is engineered for
performance, convenience, durability, unequaled power, superb balance and superior dust pick-up.
The new low deck design combined with the adjustable illuminator light make working in hard-toreach places easier than ever before. In addition, the FlexiSand has a unique adjustable handle.
The push button activated handle is easy to use and is adjustable to meet the needs of any user.
®
When operated with one of Bona’s DCS systems, the FlexiSand is virtually dust free, meaning
healthier working conditions for you, and better finish results leading to complete satisfaction of
your customers.
Innovative vacuum chamber for superior dust pick-up
Low deck height for access to toe kicks and other hard-to-reach places
Floating dust skirt adjust automatically
Large wheels for easy maneuverability when transporting
Hydraulically adjustable handle height at the push of a button
Technical data
Motor: 1.5 HP Heavy Duty, Dual Capacitor 115 Volt/175 RPM, 15 AMP, 60HZ
Gear Box: 10-1, All-Steel, Permanently Sealed & Lubricated
Switch: Dual Control Safety Lock Trigger Mechanism
Machine Weight: 102 Lbs. With Pad Driver
Pad Driver Size: Net 16” for 16” Pads, Discs and Screens
Illumination: Two long-life, high-output LED Bulbs
Order Information
Item#
AM0310010
Lbs.
102
FlexiSand Drive Plate
AS0312501
7
Accessories
Bona Multidisc
Innovative - 6 Disc drive plate creates the perfect surface for a Bona Finish System. The six, 5”
disc’s spin independently of each other, all but eliminating swirls and scratch marks, leaving the
floor smooth and flat.
Perfect for patterned and dark stained floors
Great for removing chatter marks
Uses 5” Velcro backed abrasives
Item#
AS0312520
Rev 02/12
This data sheet replaces all previous versions
Lbs.
9
page 1/1
Sanding
Bona DCS Super Vac
Sanding
Technical data sheet
®
The Bona DCS Super Vac is a high-powered heavy-duty commercial vacuum with a polished
®
chrome motor head and molded 15-gallon poly tank. The central heart of the Bona DCS Dust
Containment System, the Bona
®
DCS Super Vac is designed for maximum dust collection, balance and convenience. The high
quality filtration system offers the largest filter surface area available and greater vacuum cleaning
power along with a totally enclosed disposable bag system. The Super Vac maneuvers easily
using the chrome-plated steel handle and 8” diameter heavy-duty rear wheels with the 2-1/2”
diameter ball bearing front swivel casters. The tool caddie and floor accessories make this a
®
complete machine. The Bona DCS Super Vac also comes with a 1-year warranty and owner’s
manual.
our meter
Technical data
Motor: 2 HP Bypass, 120 Volt, 12.5 AMP, 60HZ
Machine Weight: 48 Lbs.
CFM: 112
Water Lift: 106”
Filtration Surface: 1775 Sq. In.
Order Information
Item#
AM0001480
Lbs.
48
Rev 11/10
This data sheet replaces all previous versions
page 1/1
Bona® DCS® Back Vac
Sanding
Technical data sheet
®
Power, versatility and rugged performance make the Bona DCS Back Vac a unique component in
®
the Bona DCS family of machines. The Bona DCS Back Vac can be used with an enclosed-top
disposable bag made of certified HEPA filter material to capture particles down to 0.3 micron and
comply with EPA RRP regulations. This one-time-use bag features a peel-and-stick flap to seal the
contents quickly and easily. This bag achieves the first step in the double-bagging process required
by the EPA for RRP work.
®
Designed primarily to work with the Bona FlexiSand DCS Buffer, this high-powered, heavy-duty
commercial backpack vacuum delivers 1394 watts of power with an air flow of 124 CFM and a 2.5
gallon tank. All this in a comfortable, streamlined, lightweight vacuum that rests snugly on your
back with padded shoulder and waist straps and a convenient fingertip off/on switch. Whether
working on wide open floors, tight kitchen areas with the buffer, or when just using vacuuming
tools, you have the flexibility to maneuver without a trailing hose/cord assembly. Nothing compares
®
to the speed, power, and efficiency provided by the Bona DCS Back Vac.
our meter
Technical data
Motor: 1394 Watts, 115 Volt, 12 Amps
Machine Weight: 13 lbs.
Machine Height: 30”
Airflow: 124 CFM
Capacity: 10 Qt. Micro-lined
Static Lift: 101”
Filtration Surface: 357 sq inches
Filtration Rating: Standard disposable bag or 99.97% efficient HEPA disposable bag
Order Information
®
Bona DCS Back Vac
Item#
Lbs.
AM0003510
13
Disposable HEPA filters
Item#
#/pack
AS3815521
3
Paper Filter Bags
Item#
#/pack
AS16100954
10
Rev 05/12
This data sheet replaces all previous versions
page 1/1
®
Bona BLUE Anti-Static
Abrasives
Sanding
Technical data sheet
The new Bona BLUE Anti-Static abrasives consist of an innovative combination of grit materials
and anti-static properties, designed to give you aggressive performance without sacrificing
smoothness, at a tremendous value. The addition of anti-static properties helps prevent dust from
clinging to the belt, which leads to a more consistent cut, less dust on the floor, and will keep
your machine cleaner. When other belts stop cutting, Bona BLUE keeps on working with high
efficiency and smooth results. BLUE. Powerful. Smooth. You’ve never experienced an abrasive like
this. New Anti-static abrasives available in 24-120 grit.
Order Information
8" Sanding Belt ( 77/8" X 291/2")
ITEM NO.
GRIT
AAS834000163* 16
AAS467700243 24
AAS467700363 36
AAS467700403 40
AAS467700503 50
AAS467700603 60
AAS467700803 80
AAS467701003 100
AAS467701203 120
*16-grit not Anti-Static
NO./CASE
10
10
10
10
10
10
10
10
10
LBS./CASE
7
7
6.5
5.5
5
4.5
4
4
4
10" Sanding Belt ( 97/8" X 291/2")
ITEM NO.
GRIT
NO./CASE
LBS./CASE
AAS834100163*
AAS467800243
AAS467800363
AAS467800403
AAS467800503
AAS467800603
AAS467800803
AAS467801003
AAS467801203
16
24
36
40
50
60
80
100
120
10
10
10
10
10
10
10
10
10
8
8
7.5
6.5
5.5
5.5
4.5
4
4
12" Sanding Belt (H) ( 117/8" X 311/2")
ITEM NO.
GRIT
NO./CASE
LBS./CASE
AAS834200163*
AAS470100243
AAS470100363
AAS470100403
AAS470100503
AAS470100603
AAS470100803
AAS470101003
AAS470101203
16
24
36
40
50
60
80
100
120
10
10
10
10
10
10
10
10
10
11
10
10
8.5
8
6.5
6
6
6
12" Sanding Belt (G) ( 117/8" X 291/2")
ITEM NO.
GRIT
NO./CASE
LBS./CASE
AAS861000163*
AAS470000243
AAS470000363
AAS470000403
AAS470000503
AAS470000603
AAS470000803
AAS470001003
AAS470001203
16
24
36
40
50
60
80
100
120
10
10
10
10
10
10
10
10
10
11
10.5
10
8.5
8
6.5
6
6
6
Rev 11/10
This data sheet replaces all previous versions
page 1/1
®
Bona Blue Edger Discs
Sanding
Technical data sheet
The Bona Blue Anti-Static edger discs consist of an innovative combination of grit materials and
anti-static properties, designed to give you aggressive performance without sacrificing smoothness,
at a tremendous value. The addition of anti-static properties helps prevent dust from clinging to the
disc, which leads to a more consistent cut, less dust on the floor and will keep your machine
cleaner. When discs stop cutting, Bona BLUE keeps on working with high efficiency and smooth
results. The cloth backing helps in minimizing friction caused by the revolutions of the edger thus
providing longer life in the disc.
Siafast quick-changing discs that may also be used with bolt-on systems
More aggressive, consistent cut
Less dust on the floor
Keeps machine cleaner
Cloth backing
Less clogging
Technical data
7" Bona Blue Anti-static Edger Discs
Grit
24
36
40
50
60
80
100
120
No./Pkg
25
25
50
50
50
50
50
50
Directions
1. For edgers with conversion disc, simply center disc and press onto plate. For bolt on use,
remove bolt, apply disc to edger and fasten bolt securely.
2. The siafast backing will work with 7/8” and 5/16” bolt hole patterns.
Order Information
Item#
AAS470500245
AAS470500365
AAS470500406
AAS470500506
AAS470500606
AAS470500806
AAS470501006
AAS470501206
Grit
24
36
40
50
60
80
100
120
Rev 11/10
This data sheet replaces all previous versions
#/Box
25
25
50
50
50
50
50
50
#/Case
100
100
100
200
200
200
200
200
Lbs./Case
10
10
10
15
13
12
11
11
page 1/1
siafast Edger Discs
Sanding
Technical data sheet
The SIAFAST system is the modern, quick-change edger disc system. Discs have a Velcro®like (hook and loop) fastening system. With the Conversion Disc mounted on your edger disc
pad, discs press into place and peel to remove in just seconds.
Quick-changing discs save time and money
Easy to use – No more edger wrenches. Change your disc in 5 seconds.
Cooler sanding means less clogging – discs last longer
High-quality abrasive for durability and performance
Guaranteed not to slip up to 8,900 RPM (most edgers run at 3,600 RPM)
Fits all 7” edgers
Directions
1. Clean edger disc pad surface thoroughly and allow to dry. A good grade of mineral spirits
works well.
2. Remove backing from Conversion Disc and center exactly on edger pad. Press over entire
surface to ensure full contact.
If you want to retain your bolt-on/off paper option, remove bolt and washer, cut a 7/8” diameter hole in the center of the
Conversion Disc before mountin on edger pad to give you access to your bolt and washer. Replace bolt and washer
after Conversion Disc is installed.
On rubber edger pads, cut hole as above in order to bolt Conversion Disc to pad. A little contact cement around the
outer edge of the Conversion Disc and pad will also help to secure Conversion Disc.
3. Attach SIAFAST edger sanding disc by pressing into place on Conversion Disc.
Order Information
7" Bona Edger Discs
ITEM NO.
AAS24850301
AAS24850401
AAS24850501
AAS24850601
AAS22450701
AAS24850801
AAS24850901
AAS24851001
AAS24851101
*16-grit not Anti-Static
GRIT
16
24
36
40
50
60
80
100
120
NO./CASE
250
250
250
500
500
500
500
500
500
LBS./CASE
35
20
20
30
25
20
20
20
20
7" x 7/8” Bona Edger Discs
ITEM NO.
GRIT
AAS19164506
16
AAS19164606
24
AAS19164706
36
AAS19164806
40
AAS19164906
50
AAS19165006
60
AAS19165106
80
AAS19165206
100
AAS19165306
120
NO./CASE
250
250
250
500
500
500
500
500
500
LBS./CASE
35
20
20
30
25
20
20
20
20
7” x 5/16” Bona Edger Discs
ITEM NO.
GRIT
AAS22497506
16
AAS22497706
24
AAS22497906
36
AAS22498006
40
AAS22498106
50
AAS22498206
60
AAS22498306
80
AAS22498406
100
AAS22498506
120
NO./CASE
250
250
250
500
500
500
500
500
500
LBS./CASE
35
20
20
30
25
20
20
20
20
6-7/8” Bona Edger Discs
ITEM NO.
GRIT
AAS467000365
36
AAS467000406
40
AAS467000506
50
AAS467000606
60
AAS467000806
80
AAS467001006
100
NO./CASE
250
500
500
500
500
500
LBS./CASE
20
30
25
20
20
20
6” Bona Edger Discs
ITEM NO.
AAS46700365
AAS46850036
AAS46850040
AAS46850050
AAS46850060
AAS46850080
AAS46850100
AAS46850120
NO./CASE
250
250
500
500
500
500
500
500
LBS./CASE
20
20
30
25
20
20
20
20
GRIT
36
36
40
50
60
80
100
120
Rev 11/10
This data sheet replaces all previous versions
page 1/1
Double Sided Sanding Discs
Sanding
Technical data sheet
For exceptionally flat sanding on all wood floors with a buffer, Double-sided sanding discs
provide more aggressive and cleaner cutting than traditional screens or single-sided discs.
The unique design eliminates the need for an extra hardplate.
Unique 16” disc is coated on both sides for maximum efficiency
Double-sided discs are rigid – will not tear, wrinkle or waffle like single-sided discs
No “dish-out” of soft grain like a screen
More durable and longer life than screens or single-sided discs
Sands exceptionally flat. Idea for parquet, inlays, borders, and multi-specie floors, as well as
traditional strip and plank
Ideal for scarifying concrete and abrading slab leveling materials to achieve a flat and smooth
surface
®
Simply use the Double-sided disc as you would a screen, driving it under a Bona Conditioning
Pad – No hardplate needed!
Fits all 16” buffers
Technical data
Grit Type
Grit
No./Pkg/
16
10
24
10
36
10
60
10
Silicone Carbide
80
100
120
10
10
10
150
10
180
10
220
10
Order Information
Item#
AAS19163602
AAS19163802
AAS19163902
AAS19164202
AAS19164302
AAS19164402
AAS19167601
AAS20317601
AAS19330401
AAS26547801
AAS26547901
Grit
16
24
36
60
80
100
120
120
150
180
220
Rev 11/10
This data sheet replaces all previous versions
#/Case
10
10
10
10
10
10
10
10
10
10
10
Lbs./Case
7.5
7.5
7.5
4
4
4
4
4
4
4
4
page 1/1
Screens
Sanding
Technical data sheet
Consistent, open mesh construction reduces loading. Improved grit retention extends life of screen
and decreases sanding times by not having to change your screens as often. Provides a consistent
scratch throughout the wood surface, resulting in a more uniform look.
Full Resin Bond
More consistant scratch pattern
Excellent grain retention
Reclosable box for protection
Shrinkwrapped to prevent grit loss
Available in 16” ~ 60, 80, 100, 120, 150, 180 and 220 grit
Technical data
Grit Type
Grit
No./Pkg/
60
10
80
10
100
10
Silicone Carbide
120
150
10
10
180
10
220
10
Order Information
Item#
AAS16637002
AAS16637102
AAS16637202
AAS16637302
AAS16637402
AAS16637502
AAS16637602
Grit
60
80
100
120
150
180
220
Rev 11/10
This data sheet replaces all previous versions
#/Case
10
10
10
10
10
10
10
Lbs./Case
3.8
3.5
3.0
2.5
2.5
2.5
2.5
page 1/1
®
Bona Conditioning Pad
Sanding
Technical data sheet
This unique Pad out-performs any abrasive or conditioning material used in the wood flooring
industry today for abrading wood floors between finish coats. The Conditioning Pad is designed
for use on waterborne finishes but works equally well on solvent-based finishes. The conforming
nature of the pads makes them ideal for most wood floor finish surfaces insuring optimum
bonding and the smoothest possible final coat. Conditioning Pads are used with siafast Delta
Sheets for additional abrasion to eliminate grain raise.
Will not leave unslightly scratches
Abrades finish surfaces thoroughly for uniform appearance and good adhesion.
Conforms to uneven surfaces – no shiny seams or low areas.
Will not mar or burn the finish surface.
Cleans easily by vacuuming.
Long wear life compared with other abrasives.
Glides smoothly over finish surfaces.
Technical data
Available in 16” or 20” diamaters.
10 pads per package.
Recommended Use
Intercoat abrasion for sealers and finishes.
Excellent for cleaning floor prior to recoat.
Directions
This Conditioning Pad from Bona is the new standard for surface conditioning of waterborne
and solvent-based sealers and finishes. It is ideal for deburring, cleaning and smoothing wood floor
sealers and finishes prior to the application of additional coats. When used on waterborne sealers
with siafast Delta Sheets, a smooth surface is prepared for finish coats while controlling grain raise.
Two Pads can be used under the buffer. This allows air to circulate and helps eliminate friction
heat that contributes to gumming and loading of the Conditioning Pad and the Delta Sheets.
Order Information
Item#
AAS19522203
AAS19522101
Size/Grit
16”/320
20”/320
Rev 11/10
This data sheet replaces all previous versions
#/Case
10
10
Lbs./Case
4
4
page 1/1
siafast Delta Sheet
Sanding
Technical data sheet
siafast Delta Sheets are designed for abrading Bonaseal® sealer to eliminate grain raise. Delta
Sheets are used attached to Bona® Conditioning Pads as shown in the photo above. The unique
“delta” shape and nature of the abrasive compound provide superior performance with a minimum
of loading.
®
Eliminates grain raise when used to smooth Bonaseal
Superior non-loading characteristics and contoured delta shape means increased production
capacity per sheet.
Easy to use! Just press into position. No bolts, screws or ties. No cutting or measuring.
Technical data
10 sheets per package
100 sheets per case (loose)
Recommended Use
®
siafast Delta Sheets are designed to be used attached to Bona Conditioning Pads for
®
smoothing Bonaseal prior to applying the first finish coat.
Removes raised wood fiber and ridges that create a rough surface.
Intercoat abrasion of solvent-based sealers and finishes when more aggressive abrading is
required than the Conditioning Pad can provide alone.
Directions
®
1. It is recommended that 2 Delta Sheets be placed on the buffer’s drive Pad (Bona Conditioning
Pad) arranged according to the illustration on the front of this sheet. This provides optimum cutting
at a faster walking speed.
2. When operating a buffer with the Pad and Delta Sheets it is important to walk and move the
machine quickly along the floor. When abrading, heat resulting from moving too slowly may cause
the sealer to “gum” and collect too quickly on the Sheets or the Pad. (Screens or other stiff
abrasives generate too much heat and work poorly for this purpose.)
3. Check the Delta Sheets and Pad frequently, perhaps every 50 square feet or so, for residue
build-up. If they are allowed to collect cut residue, floor surface scratches may result. If cut residue
is loading on the Sheets or Pad, it can be removed by tapping or scraping the surfaces with a piece
of cardboard or a plastic scraper.
4. It is very important to overlap buffing lanes completely, making sure the abrasion pattern is
uniform. This is especially true when changing Delta Sheets or Pads or turning the Pads over to
the clean side. (Uneven abrasion technique may result in an uneven look when the finish is
®
applied.) NOTE: Bona Conditioning Pads are approximately 3/8” thick when new and compress
when used. They provide very aggressive abrading when used to drive a screen on raw wood.
®
However, when used for intercoat conditioning of Bonaseal , consider using two Conditioning
Pads, sandwiched together, to drive the Delta Sheets. This provides additional cushioning and
allows more air to flow through the Pads, which helps to reduce heat buildup and keeps the loading
of the Pad and Delta Sheets to a minimum.
5. Have several Pads available when doing larger jobs. It is more convenient to change Pads on
the buffer every three or four hundred feet, and then vacuum them all at one time at the end of the
buffing procedure.
Order Information
Item#
AA0001027
AA0001028
Grit
150
150
Rev 11/10
This data sheet replaces all previous versions
#/Case
10 pk.
50 ea.
Lbs./Case
1.5 oz.
9.4 oz.
page 1/1
Bona R848
Adhesives
Technical data sheet
Bona R848 is a one-component, moisture curing, water and solvent free, silane-based adhesive for
engineered wood floors. Bona R848 provides outstanding adhesion to a variety of surfaces, and allows
for the natural movement of wood flooring.
Excellent “green grab” means the flooring stays in place
No “memory” – Floor seams will not move apart
Rapid shear strength development – Flooring is ready for furniture and foot traffic in one day
Easy to clean – Will not harm the finish on pre-finished floors; will not stain hands
Easy to apply – No arm fatigue
Exceptional ridge stability provides maximum adhesive transfer
GREENGUARD Indoor Air Quality Certified®
Moisture protection up to 6lbs or 80% RH
Very low VOC – Meets the criteria for LEED EQc 4.1 (v. 2.1, 2.2, 3.0)
California Proposition 65 Compliant
Can be used with radiant heat systems
Technical data
Physical Characteristics:
Ingredients – Calcium carbonate, plasticizers, silane-modified prepolymer, amorphous silica
Base – Silane Modified-Prepolymer
Color – Grey
Density – 13.2 lbs./gallon
VOC Content – maximum content of 20
Shear Strength – 245psi (at final cure; lap shear test, 1mm gap)
Elongation – 300%
Odor – Non-offending
Flash Point – >100º C (212ºF) (Pensky-Martens)
Stability – 12 months from date of manufacture in unopened, original packaging
Packaging – 2.5 gallon (15 kg) containers
Application Characteristics:
Spread Rating – Easy to spread, maintains excellent ridge stability
Open Time- 30 minutes
Coverage – See “Trowel Notch Requirements” for spread rate
Curing – Light foot traffic - 8-10 hours
Furniture, fixtures - 12-24 hours
Unfinished floor sanding - after 24 hours
Recommended Use
Commercial and residential. Use with engineered prefinished and unfinished flooring; on, above or below
grade1. May be used on both wood and concrete substrates2.
1
Read and follow flooring manufacturer instructions, recommendations and limitations as to the suitability
of a particular flooring product to certain jobsite conditions and installation methods.
2
After proper site conditions, moisture testing results and substrate preparation have been met. See
“Directions for Use” for acceptable jobsite conditions.
Directions
DIRECTIONS FOR USE:
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
APPLICATION: Use notched trowel (available from Bona)
Drying time: 24 hours under normal conditions
Coverage: 90 square feet per gallon when used for adhesion with moisture content below 3 lbs/24
hours/1000 square feet or 75% RH. 50-55 square feet per gallon when used for adhesion and moisture
control up to 6 lbs/24 hours/1000 square feet or 80% RH. 100% COVERAGE/TRANSFER RATE IS
REQUIRED FOR MOISTURE PROTECTION. To achieve 100% coverage rate, skim coat the floor
utilizing the flat side of the Bona 1250G trowel to create a smooth surface free of voids. While skim coat is
still wet, apply a second layer of Bona R848 with the Bona 1250G trowel using normal trowel on
application.
ACCLIMATION AND SITE CONDITIONS: Acclimate adhesive and flooring to room temperature at the
jobsite 72 hours before installation. Building climate control system must be functioning with a
temperature of 65ºF - 80ºF and maximum relative humidity of 70% for 72 hours before flooring is
installed, during installation, and for 72 hours after installation.
Rev 10/12
This data sheet replaces all previous versions
page 1/2
Bona R848
Adhesives
Technical data sheet
MOISTURE TESTING: For concrete slabs, using standard application, conduct moisture testing per
ASTM test methods F1869 Test for Measuring Moisture Vapor Emission Rate (MVER) of Concrete
Subfloor Using Anhydrous Calcium Chloride and/or F2170 Test Method for Determining Relative Humidity
in Concrete Floor Slabs Using In Situ Probes. Contact ASTM International to obtain copies of the test
methods before proceeding. MVER using ASTM F1869 (Calcium chloride test) must not exceed 6
lbs/24 hours/1000 square feet. Relative Humidity using ASTM F2170 (RH Probe test) must not
exceed 80%. If readings exceed limits, use Bona R580 Moisture Barrier according to label
directions prior to application of Bona 848, or use Bona R851 in place of Bona R580 and Bona
R848.
SUBSTRATE PREPARATION: Substrate must be clean, smooth, dry, free of loose material and
structurally sound, with the surface slightly textured for best adhesion (similar to a light broom finished
concrete). Remove adhesive residue, paint, concrete curing compounds or other contaminants that may
affect adhesive bond. Surface cracks, grooves, depressions, control joints or other non-moving joints, and
other irregularities must be filled or smoothed with a Portland Cement based patching and levelling
compound. Substrate must be level to 3/16” in a 10 foot span. Do not install wood flooring before the
compound has fully cured. Do not install over expansion joints or other moving joints in a concrete slab.
Slab temperatures must be between 55º and 95ºF. Suitable substrates include concrete, plywood, cork,
particle or chip board, stone, ceramic, terrazzo, radiant heat flooring (refer to manufacturer’s
recommended installation instructions) and dry above-grade gypsum underlayments.
PRODUCT LIMITATIONS: Bona R848 will not prevent moisture-related damages to wood flooring
originating from the top, sides or ends of flooring (water leaks, puddles, hydrostatic head, etc.) nor does it
eliminate other moisture or installation related issues such as improper acclimation of flooring or the
effects of jobsite temperature and humidity.
DO NOT USE BONA R848:
On solid floor installations – for use with engineered flooring only
On wet, contaminated or friable surfaces
Over concrete curing compounds, sealers or other surface treatments that could affect adhesion
On areas subject to hydrostatic head
On cutback residue, or over vinyl/VCT
On chemically treated woods (stain, preservatives, etc.)
As a leveling compound
TROWEL NOTCH REQUIREMENTS (Spread rates are approximate):
Replace as needed to achieve proper spread rate.
SPREADING ADHESIVE AND LAYING FLOORING: Spread adhesive on the substrate while holding the
Bona trowel at a 90º angle, using a smooth semicircular motion. Do not leave any puddles of adhesive.
Set the flooring into adhesive while the adhesive is still wet. Do not allow more than 30 minutes of open
time before setting flooring into the adhesive. Higher humidity can decrease open time. DO NOT SET
FLOORING INTO ADHESIVE THAT HAS SKINNED OVER. REMOVE ADHESIVE AND REAPPLY.
Maintenance
CLEAN-UP: Clean adhesive from the surface of the floor immediately, while wet. Use mineral spirits on a
clean white cloth.
STORAGE: Store in a climate controlled environment. Keep from freezing. Do not store for extended
periods in excess of 90ºF.
Order Information
Item#
Size
BR84806100USBO 2.5 gallon
Rev 10/12
This data sheet replaces all previous versions
#/Case
1
Lbs./Case
34
page 2/2
Bona R580
Adhesives
Technical data sheet
®
Bona R580 moisture barrier sealer optimizes adheasion to, and provides a protective membrane
1
over substrates where the moisture content exceeds 12 lbs or 85% relative humidity. It is a
moisture cured, solvent and water free, silane-based compound. It can be used as either a 1 or 2component product.
1 or 2-component system: 2-component system includes a catalyst to accelerate setting time.
Easy application
1
Moisture barrier protection above 12 lbs or 85% relative humidity
Very low VOC – Meets the criteria for LEED EQc 4.1 (v. 2.1, 2.2, 3.0)
Single coat application
Self-leveling
Easy tool clean-up
®
GREENGUARD Indoor Air Quality Certified
California Proposition 65 Compliant
1
Use on concrete, cementitious or wood substrates where moisture is a known or potential issue;
where the moisture content is greater than 12 lbs (Calcium Chloride test) or 85% relative humidity
(RH probe test) but not greater than 18 lbs or 95% relative humidity.
Technical data
Physical Characteristics:
Ingredients – Silane-based polymer, Calcium Carbonate, Triethoxypropylsilane, Amine, and
Amorphous Silica.
Base – Silane Modified-Prepolymer
Color – Off-white
Viscosity – 10 Pa.s at a shear rate of 10 1/sec (cone-plate rheometer)
Density – 10.43 lbs/gallon
VOC Content – <40 grams per liter
Odor – Non-offending
Flash Point – >100º C (212ºF) (Pensky-Martens)
Stability – 1 year from date of manufacture in unopened, original packaging
Packaging – 2.5 gallon pail (includes foil packet containing catalyst)
Application Characteristics:
Spreadability – Easy to spread, self-leveling
Open Time- 20 minutes (2 component) / 40 minutes (1 component)
Cure Time – 24 hours
Coverage – See “Trowel Notch Requirements” for spread rate
Dry Time – 4 hours (2 Component system) / 6 hours (1 component system)
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEET.
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
MOISTURE TESTING: For concrete slabs, conduct moisture testing per ASTM test methods
F1869 “Test Method for Measuring Moisture Vapor Emission Rate (MVER) of Concrete Subfloor
Using Anhydrous Calcium Chloride”, and/or F2170 “Test Method for Determining Relative Humidity
in Concrete Floor Slabs Using In Situ Probes”. Contact ASTM International to obtain copies of the
test methods before proceeding. Use Bona R580 Moisture Barrier Sealer prior to installation of
hardwood flooring with a Bona adhesive when MVER using ASTM F1869 (Calcium Chloride test)
exceeds 12 lbs/24 hours/1000 square feet or when using ASTM F2170 (RH probe test) exceeds
85% relative humidity. The maximum moisture content should not exceed 18 lbs/24 hours/1000
square feet or 95% relative humidity.
ACCLIMATION AND SITE CONDITIONS: Building climate control system must be functioning with
a temperature of 65°- 80°F and maximum relative humidity of 70% for 72 hours before flooring is
installed, during installation, and for 72 hours after installation. Acclimate flooring according to
manufacturer's instructions. Acclimate Bona R580 Moisture Barrier Sealer and Bona R851
Adhesive to the room temperature of installation; usually overnight.
SUBSTRATE PREPARATION: Substrate must be clean, smooth, dry, free of loose material and
structurally sound, with the surface slightly textured for best adhesion (similar to a light broom
finished concrete). Remove adhesive residue, paint, concrete curing compounds or other
contaminants that may affect adhesive bond. Sandblasting, shotblasting or scarifying may be
Rev 01/12
This data sheet replaces all previous versions
page 1/2
Bona R580
Adhesives
Technical data sheet
necessary to completely remove some of these residues. Surface cracks, grooves, depressions,
control joints or other non-moving joints, and other irregularities must be filled or smoothed with a
Portland Cement-based patching and/or leveling compound. Substrate must be level to 3/16” in a
10 foot span. Slab temperatures must be between 55° and 95°F. NOTE: If a concrete slab needs
to be leveled, Bona R580 Moisture Barrier Sealer must be applied to the slab prior to application of
the leveling compound. See detailed instructions below. Other suitable substrates include wood
and radiant heat flooring (refer to manufacturer’s recommended installation instructions).
PRODUCT LIMITATIONS: Bona R580 is designed to reduce moisture vapor emissions that
originate from below the membrane only. It does not affect other issues originating from the top,
sides or ends of flooring (water leaks, puddles, hydrostatic head, etc.) nor does it eliminate other
moisture or installation related issues such as improper acclimation of flooring or the effects of
jobsite temperature and humidity.
DO NOT USE BONA R580:
Over concrete curing compounds, sealers or other surface treatments that could affect
adhesion
On areas subject to hydrostatic head
On cutback residue, or over vinyl/VCT
On chemically treated woods (stain, preservatives, etc.)
As a leveling compound
As an adhesive
TROWEL NOTCH REQUIREMENTS (Spread rate is approximate):
Replace as needed to achieve proper spread rate.
Bona Spreader Trowel 500F / 1/16” x 1/16” fine V-notch / 130 sq. ft/gallon
APPLICATION: 2 Component system (4 hour dry time) – R580 comes with a foil packet containing
a pre-measured catalyst (water) that accelerates the setting time when mixed together with the
sealer. 1. Add the entire contents of the foil pouch to the sealer and mix well using a mix paddle
and drill. After the catalyst is added you will have 20 minutes of open time to spread the sealer
before it begins to set. 2. Spread sealer evenly on the substrate with the Bona spreader trowel
using a snowplow application method. Bona R580 is designed to self-level and create a continuous
membrane without the need for flat troweling. Note: If using a leveling compound, you will need to
broadcast quartz sand into the wet sealer within 40 minutes of application. See instructions below.
1 Component system (6 hour dry time) – R580 can also be used as a single component system
without the catalyst. Mix well using a mix paddle and drill. Follow the instructions above beginning
with #2. Flooring should be installed or leveling compound applied within 72 hours. If no leveling is
needed, to protect membrane from possible job-site contamination, once dry, cover with 1 mil poly
sheeting. Peel back sheeting in working sections as R851 adhesive and flooring is installed.
LEVELING COMPOUND: The substrate must be level to 3/16” in a 10 foot span. If not, you must
use a Portland Cement-based leveling compound. The Bona R580 Moisture Barrier Sealer is
applied to the slab prior to the application of the leveling compound. 1. When the sealer is still fresh
and wet (no longer than 40 minutes), broadcast quartz sand (36-60 grit / 30-50 USS mesh or .3 .8mm grain size) into the R580 sealer until rejection. 2. After the sealer has dried (4 to 6 hours),
sweep and vacuum the excess sand from the entire surface. The sand provides a strong,
mechanical bond for the leveling compound. 3. Apply leveling compound following manufacturer
instructions and required dry times prior to applying Bona R851 Adhesive and installing floor.
Maintenance
CLEAN-UP: Replace foil liner on top of any unused sealer in pail prior to storage. Clean sealer
from tools and surfaces using mineral spirits (best removed when sealer is still wet).
STORAGE: Store in a climate controlled environment. Keep from freezing. Do not store for
extended periods above 90°F (32°C).
Order Information
Item#
BR580025US
Size
2.5 Gallon
Rev 01/12
This data sheet replaces all previous versions
#/Case
1
Lbs./Case
28
page 2/2
Bona R851
Adhesives
Technical data sheet
Bona R851 is a one-component, moisture curing, water and solvent free, silane-based adhesive for
wood floors. Bona R851 provides outstanding adhesion to a variety of surfaces, and allows for the
natural movement of wood flooring.
Excellent “green grab” means the flooring stays in place
No “memory” – Floor seams will not move apart
Rapid shear strength development – Flooring is ready for furniture and foot traffic in one day
Easy to clean – Will not harm the finish on pre-finished floors; will not stain hands
Easy to apply – No arm fatigue
Exceptional ridge stability provides maximum adhesive transfer
®
GREENGUARD Indoor Air Quality Certified
Moisture protection up to 15lbs or 85% RH
Very low VOC – Meets the criteria for LEED EQc 4.1 (v. 2.1, 2.2, 3.0)
California Proposition 65 Compliant
Technical data
Physical Characteristics:
Ingredients – Calcium carbonate, silane modified prepolymer, plasticizers, amorphous silica
Base – Silane Modified-Prepolymer
Color – Cream
Viscosity – 38 Pa.s at a shear rate of 10 1/sec (cone-plate rheometer)
Density – 12.5 lbs./gallon
VOC Content – Negligible
Shear Strength – 335psi (at final cure; lap shear test, 1mm gap)
Elongation – 250%
Water Vapor Permeability - < .07 per ASTM E-96 Standard Test Methods for Water Vapor
Transmission of materials. Ratings are g/m2-24 hour-mmHG.
Sound Reduction Rating – 53dB per ASTM E492-04 IIC (6” concrete slab with no ceiling)
Odor – Non-offending
Flash Point – >100º C (212ºF) (Pensky-Martens)
Stability – 12 months from date of manufacture in unopened, original packaging
Packaging – 3 gallon (17.14 kg) containers
Application Characteristics:
Spread Rating – Easy to spread, maintains excellent ridge stability
Open Time- 40 minutes
Coverage – See “Trowel Notch Requirements” for spread rate
Curing – Light foot traffic - 8-10 hours
Furniture, fixtures - 12-24 hours
Unfinished floor sanding - after 24 hours
Recommended Use
Commercial and residential. Use with solid or engineered prefinished and unfinished flooring; on,
above or below grade1. May be used on both wood and concrete substrates2.
1
Read and follow flooring manufacturer instructions, recommendations and limitations as to the
suitability of a particular flooring product to certain jobsite conditions and installation methods.
2
After proper site conditions, moisture testing results and substrate preparation have been met.
See “Directions for Use” for acceptable jobsite conditions.
Directions
DIRECTIONS FOR USE:
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800/872-5515
ACCLIMATION AND SITE CONDITIONS: Acclimate adhesive and flooring to room temperature at
the jobsite 72 hours before installation. Building climate control system must be functioning with a
temperature of 65ºF - 80ºF and maximum relative humidity of 70% for 72 hours before flooring is
installed, during installation, and for 72 hours after installation.
MOISTURE TESTING: For concrete slabs, using standard application, conduct moisture testing
per ASTM test methods F1869 Test for Measuring Moisture Vapor Emission Rate (MVER) of
Concrete Subfloor Using Anhydrous Calcium Chloride and/or F2170 Test Method for Determining
Rev 01/12
This data sheet replaces all previous versions
page 1/2
Bona R851
Adhesives
Technical data sheet
Relative Humidity in Concrete Floor Slabs Using In Situ Probes. Contact ASTM International to
obtain copies of the test methods before proceeding. MVER using ASTM F1869 (Calcium
chloride test) must not exceed 12 lbs/24 hours/1000 square feet. Relative Humidity using
ASTM F2170 (RH Probe test) must not exceed 85%. If MVER readings exceed 12 lbs. but are
less than 15 lbs., the following procedure may be used. UTILIZING THE FLAT SIDE OF THE
®
BONA 1500G TROWEL, SKIM COAT R851 ONTO SUBFLOOR CREATING A SMOOTH
SURFACE FREE OF VOIDS. WHILE THE SKIM COAT OF ADHESIVE IS STILL WET, APPLY
R851 WITH THE 1500G TROWEL. For wood substrates, follow flooring manufacturer’s guidelines
including moisture content and required moisture measuring methods.
SUBSTRATE PREPARATION: Substrate must be clean, smooth, dry, free of loose material and
structurally sound, with the surface slightly textured for best adhesion (similar to a light broom
finished concrete). Remove adhesive residue, paint, concrete curing compounds or other
contaminants that may affect adhesive bond. Surface cracks, grooves, depressions, control joints
or other non-moving joints, and other irregularities must be filled or smoothed with a Portland
Cement based patching and levelling compound. Substrate must be level to 3/16” in a 10 foot
span. Do not install wood flooring before the compound has fully cured. Do not install over
expansion joints or other moving joints in a concrete slab. Slab temperatures must be between 55º
and 95ºF. Suitable substrates include concrete, plywood, cork, particle or chip board, stone,
ceramic, terrazzo, radiant heat flooring (refer to manufacturer’s recommended installation
instructions) and dry above-grade gypsum underlayments.
PRODUCT LIMITATIONS: Bona R851 will not prevent moisture-related damages to wood flooring
originating from the top, sides or ends of flooring (water leaks, puddles, hydrostatic head, etc.) nor
does it eliminate other moisture or installation related issues such as improper acclimation of
flooring or the effects of jobsite temperature and humidity.
DO NOT USE BONA R851:
On wet, contaminated or friable surfaces
Over concrete curing compounds, sealers or other surface treatments that could affect adhesion
On areas subject to hydrostatic head
On cutback residue, or over vinyl/VCT
On chemically treated woods (stain, preservatives, etc.)
As a leveling compound
TROWEL NOTCH REQUIREMENTS (Spread rates are approximate):
Replace as needed to achieve proper spread rate.
Parquet (12” x 12”) over smooth substrates – Bona 1000F Trowel 5/32” x 5/32” x 5/32” V-notch
/ 80-85 sq. ft/gallon.
Engineered or solid plank – maximum 3/4” thick and 5” width – Bona 1250G Trowel 1/4” x 1/4” x
7/16” V-notch / 60-65 sq. ft/gallon.
Engineered or solid plank – over 3/4” thick and over 5” width, maximum 8” width – Bona 1500G
Trowel 5/16” x 5/16” x 7/16” V-notch / 50-55 sq. ft/gallon.
SPREADING ADHESIVE AND LAYING FLOORING: Spread adhesive on the substrate while
holding the Bona trowel at a 90º angle, using a smooth semicircular motion. Do not leave any
puddles of adhesive. Set the flooring into adhesive while the adhesive is still wet. Do not allow
more than 40 minutes of open time before setting flooring into the adhesive. Higher humidity can
decrease open time. DO NOT SET FLOORING INTO ADHESIVE THAT HAS SKINNED OVER.
REMOVE ADHESIVE AND REAPPLY.
Maintenance
CLEAN-UP: Clean adhesive from the surface of the floor immediately, while wet. Use mineral
spirits on a clean white cloth.
STORAGE: Store in a climate controlled environment. Keep from freezing. Do not store for
extended periods in excess of 90ºF.
Order Information
Item#
BR851061US
Size
3 Gallon
Rev 01/12
This data sheet replaces all previous versions
#/Case
1
Lbs./Case
38.6
page 2/2
Bona R850T
Adhesives
Technical data sheet
Bona R850T is a one-component, moisture curing, water and solvent free, silane-based adhesive
for wood floors. Bona R850T provides outstanding adhesion to a variety of surfaces, and allows for
the natural movement of wood flooring.
Perfect alternative to face nailing close-out rows, board replacements and trim applications
Excellent initial “green grab” means the flooring stays in place
Rapid shear strength development – Flooring is ready for furniture and foot traffic in one day
Easy to clean – Will not harm the finish on pre-finished trim and floors; will not stain hands
Easy to apply – Clean, No Waste, Ergonomical design
Exceptional ridge stability provides maximum adhesive transfer
®
GREENGUARD Indoor Air Quality Certified
Very low VOC – Meets the criteria for LEED EQc 4.1 (v. 2.1, 2.2, 3.0)
Moisture protection up to 15lbs or 85% RH
California Proposition 65 Compliant
Technical data
Physical Characteristics:
Ingredients – Calcium carbonate, silane modified prepolymer, plasticizers, amorphous silica
Base – Silane Modified-Prepolymer
Color – Cream
Density – 12.5 lbs./gallon
VOC Content – Negligible
Sheer Strength – 335 psi (at final cure; lap sheer test, 1 mm gap)
Elongation – 250%
Water Vapor Permeability – < .07 per ASTM E-96 Standard Test Methods for Water Vapor
Transmission of materials. Ratings are g/m2-24 hour-mmHG.
Sound Reduction Rating – 53dB per ASTM E492-04 IIC (6” concrete slab with no ceiling)
Odor – Non-offending
Flash Point – >100º C (212ºF) (Pensky-Martens)
Stability – 12 months from date of manufacture in unopened, original packaging
Application Characteristics:
Open Time - 40 minutes
Coverage – 60 L’ per tube with ¼” bead
Curing – Light foot traffic - 8-10 hours
Furniture, fixtures - 12-24 hours
Unfinished floor sanding - after 24 hours
Recommended Use
Replaces top nailing on close-out rows and board replacements.
Supplemental fastening for wide plank boards when nailing and gluing are needed
Idea for projects where traditional fastening isn’t practical – hard to reach areas, radiant heat
floors…
Commercial and residential. Use with solid or engineered prefinished and unfinished flooring; on,
1
2
above or below grade . May be used on both wood and concrete substrates .
1
Read and follow flooring manufacturer instructions, recommendations and limitations as to the
suitability of a particular flooring product to certain jobsite conditions and installation methods.
2
After proper site conditions, moisture testing results and substrate preparation have been met.
See “Directions for Use” for acceptable jobsite conditions.
Directions
BEFORE USING, READ ALL DIRECTIONS AND MATERIAL SAFETY DATA SHEETS.
FOR TECHNICAL ADVICE: Call Bona US at 800-872-5515
ACCLIMATION AND SITE CONDITIONS: Acclimate adhesive and flooring to room temperature at
the jobsite 72 hours before installation. Building climate control system must be functioning with a
temperature of 65ºF - 80ºF and maximum relative humidity of 70% for 72 hours before flooring is
installed, during installation, and for 72 hours after installation.
Rev 01/12
This data sheet replaces all previous versions
page 1/2
Bona R850T
Adhesives
Technical data sheet
MOISTURE TESTING: For concrete slabs, conduct moisture testing per ASTM test methods
F1869 Test for Measuring Moisture Vapor Emission Rate (MVER) of Concrete Subfloor Using
Anhydrous Calcium Chloride and/or F2170 Test Method for Determining Relative Humidity in
Concrete Floor Slabs Using In Situ Probes. Contact ASTM International to obtain copies of the test
methods before proceeding. MVER using ASTM F1869 (Calcium chloride test) must not
exceed 15 lbs/24 hours/1000 square feet. Relative Humidity using ASTM F2170 (RH Probe
test) must not exceed 85%. If readings exceed these limits, DO NOT USE BONA R850T. For
wood substrates, follow flooring manufacturer’s guidelines including moisture content and required
moisture measuring methods.
SUBSTRATE PREPARATION: Substrate must be clean, smooth, dry, free of loose material and
structurally sound, with the surface slightly textured for best adhesion (similar to a light broom
finished concrete). Remove adhesive residue, paint, concrete curing compounds or other
contaminants that may affect adhesive bond. Surface cracks, grooves, depressions, control joints
or other non-moving joints, and other irregularities must be filled or smoothed with a Portland
Cement based patching and levelling compound. Substrate must be level to 3/16” in a 10 foot
span. Do not install wood flooring before the compound has fully cured. Do not install over
expansion joints or other moving joints in a concrete slab. Slab temperatures must be between 55º
and 95ºF. Suitable substrates include concrete, plywood, particle or chip board, stone, ceramic,
terrazzo, radiant heat flooring (refer to manufacturer’s recommended installation instructions) and
dry above-grade gypsum underlayments.
PRODUCT LIMITATIONS: Bona R850T will not prevent moisture-related damages to wood
flooring originating from the top, sides or ends of flooring (water leaks, puddles, hydrostatic head,
etc.) nor does it eliminate other moisture or installation related issues such as improper acclimation
of flooring or the effects of jobsite temperature and humidity.
DO NOT USE BONA R850T:
On wet, contaminated or friable surfaces
Over concrete curing compounds, sealers or other surface treatments that could affect adhesion
On areas subject to hydrostatic head
On cutback residue, or over vinyl/VCT
On chemically treated woods (stain, preservatives, etc.)
As a leveling compound
APPLICATION:
Remove end cap of applicator gun and pull back piston.
Insert R850T tube into applicator gun, cut the exposed end of the R850T tube.
Replace end cap – make sure to use the supplied applicator cone.
Apply by pulling applicator gun trigger.
Apply adhesive in a “s” pattern for best results.
Maintenance
CLEAN-UP: Clean adhesive from the surface of the floor immediately, while wet. Use mineral
spirits on a clean white cloth.
STORAGE: Store in a climate controlled environment. Keep from freezing. Do not store for
extended periods in excess of 90º.
Ordering Information
Bona R850T
Item#: BR850T5600USBO
#/Case: 12
Bona Applicator Gun
Item#: AT32042000
#/Case: 1
Rev 01/12
This data sheet replaces all previous versions
page 2/2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement