Radio Shack | ET-531 | Owner`s manual | Radio Shack ET-531 Owner`s manual

43-1031.fm Page 1 Tuesday, August 17, 1999 9:24 AM
Cat. No. 43-1031
OWNER’S MANUAL
Please read before using this equipment.
ET-531
10-Channel Cordless Telephone
with 10-Memory Speed Dialing
43-1031.fm Page 2 Tuesday, August 17, 1999 9:24 AM
FEATURES
Your Radio Shack ET-531 10-Channel
Cordless Telephone with 10-Memory
Speed Dialing includes the latest advances in cordless phone technology.
Redial — quickly redials the last number dialed, with the touch of a button.
It includes the following features:
Touch Tone or Pulse (Rotary) Dialing — lets you connect your phone to
either type of service.
10-Channel Selector — lets you easily select the channel with the best performance and least interference.
Hearing-Aid Compatibility — lets
you use your phone with hearing aids
that have a T (telephone) switch.
Advanced Super CCT Circuitry —
provides clarity comparable to a corded phone, reduces background noise,
and increases effective operating distance.
For your records, we urge you to
record the serial number of your phone
in the space below. The serial number
is located on the bottom panel of the
base.
10-Number Memory — lets you store
10 phone numbers in memory for easy
dialing.
Serial Number:__________________
COM-LOK — ensures that other cordless phone users cannot use your
phone line while the handset is on the
base.
Automatic Security Access Code —
changes each time you return the
handset to the base to help prevent
other cordless phone users from using
your phone line while the handset is off
the base.
Flash — sends an electronic switchhook signal for use with special phone
services such as call waiting.
Please read this owner’s manual carefully so you can enjoy all of your telephone’s features.
Important: Cordless phones such as
this one require AC power to operate.
When the AC power is off, you cannot
dial out or receive incoming calls using
your cordless phone. For this reason,
the cordless phone should not be your
only telephone. To be safe, you should
also have a phone that does not require AC power to operate (not a cordless phone) so you can still make and
receive calls if there is an AC power
failure.
© 1995 Tandy Corporation.
All Rights Reserved.
COM-LOK and Radio Shack are registered trademarks used by Tandy Corporation.
2
43-1031.fm Page 3 Tuesday, August 17, 1999 9:24 AM
This telephone has been tested and
found to comply with all applicable
FCC and UL standards.
Note: Your 10-Channel Cordless Telephone with 10-Memory Speed Dialing
operates on standard radio frequencies, as allocated by the FCC. Therefore, it is possible for other radio units
operating on similar frequencies, within a certain area, to inadvertently intercept your conversa-tions and/or cause
interference on your cordless telephone. This lack of privacy can occur
with any cordless telephone.
Warning: To prevent fire or shock hazard, do not expose this product to rain
or moisture.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
!
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
This symbol is intended to alert you
to the presence of uninsulated dangerous voltage within the product’s
enclosure that might be of sufficient
magnitude to constitute a risk of
electric shock. Do not open the
product’s case.
!
This symbol is intended to inform
you that important operating and
maintenance instructions are included in the literature accompanying this product.
READ THIS BEFORE
INSTALLATION
We have designed your telephone to
conform to federal regulations, and
you can connect it to most telephone
lines. However, each device that you
connect to the phone line draws power
from the phone line. We refer to this
power draw as the device’s ringer
equivalence number, or REN. The
REN is shown on the bottom of your
phone.
If you are using more than one phone
or other device on the line, add up all
the RENs. If the total is more than five,
your phone might not ring. In rural areas, a total REN of three might impair
ringer operation. If ringer operation is
impaired, remove a device from the
line.
FCC STATEMENT
This telephone complies with Part 68
of FCC Rules. You must, upon request, provide the registration number
and the REN to your phone company.
These numbers are located on the bottom of your phone.
Note: You must not connect your
phone to any of the following:
• Coin-operated systems
• Party-line systems
• Most electronic key phone systems
3
43-1031.fm Page 4 Tuesday, August 17, 1999 9:24 AM
CONTENTS
Preparation ........................................................................................................... 5
Installing the Battery ........................................................................................ 5
Installing the Handset’s Antenna .......................................................................5
Selecting a Location ........................................................................................ 5
Placing the Base on a Desk Top ............................................................... 6
Mounting the Base on a Wall Plate ........................................................... 6
Mounting the Base Directly on the Wall .................................................... 7
Charging the Battery ........................................................................................ 9
Setting the Dialing Mode ................................................................................. 9
Setting the Ringer On/Off .............................................................................. 10
Operation ............................................................................................................
Making/Answering a Call ...............................................................................
Using the Handset at the Base ...............................................................
Using the Handset Away from the Base .................................................
Reducing Interference ...................................................................................
Redial ............................................................................................................
Using Flash ....................................................................................................
Using Tone Services with a Service Number..................................................
Using Page ....................................................................................................
Memory Dialing ..............................................................................................
Storing a Number in Memory ..................................................................
Entering a Pause in a Memory Number ..................................................
Dialing a Stored Number .........................................................................
Chain Dialing Service Numbers ..............................................................
Testing Stored Emergency Numbers ......................................................
11
11
11
11
12
12
12
13
13
14
14
15
15
15
15
Troubleshooting ................................................................................................. 16
Care and Maintenance .......................................................................................
Replacing the Battery ....................................................................................
The FCC Wants You to Know ........................................................................
Lightning ........................................................................................................
4
18
19
19
20
43-1031.fm Page 5 Tuesday, August 17, 1999 9:24 AM
PREPARATION
INSTALLING THE
BATTERY
Before you use your phone for the first
time, you must install and connect the
battery, then charge it for about 12-15
hours.
To install the battery, slide off the battery compartment cover on the back of
the handset. Place the battery in the
compartment, then connect the battery
to the pins inside the battery compartment.
SELECTING A LOCATION
You can place your phone on a desk,
shelf, or table, or mount it on a wall.
Select a location that is:
• Near an AC outlet
• Near a telephone line jack
• Out of the way of normal activities
• Away from fluorescent lights, electrical machinery, electrical appliances, and metal walls or filing
cabinets
• Away from computers, remote
control toys, wireless intercoms,
alarms, and room monitors.
Then install the handset’s antenna, replace the cover, mount the phone (see
“Selecting a Location”), and follow the
instructions under “Charging the Battery.”
INSTALLING THE
HANDSET’S ANTENNA
Insert the antenna into the hole at the
top of the handset, then rotate the antenna clockwise until it is secure.
The base’s location affects the phone’s
range. If you have a choice of several
locations, try each to see which provides the best performance.
Notes:
• If the phone line jack is not a modular jack, you must update the wiring. You can do this yourself,
using jacks and adapters available at your local Radio Shack
store, or you can let the phone
company update the wiring for
you.
• The phone company will charge
you for the installation of the necessary jacks.
5
43-1031.fm Page 6 Tuesday, August 17, 1999 9:24 AM
• The USOC number of the jack to
be installed is RJ11W for a wall
jack or RJ11C for a baseboard
jack.
Caution: You must use a 120 VAC/12
VDC adapter that delivers at least 200
milliamps. Its plug must correctly fit the
phone’s 12VDC jack. The supplied
adapter meets these requirements.
Using an adapter that does not meet
these requirements could damage the
phone or the adapter.
Placing the Base on a Desk
Top
5. Place the handset upright over the
charging contacts on the top of
the base (see “Charging the Battery”).
Note: The phone will not charge if
you try to use the charging contacts on the side of the base while
it is flat on a desk top.
6. Fully extend the base’s antenna
and place it in a vertical position.
Mounting the Base on a Wall
Plate
You need a short modular cord (such
as Radio Shack Cat. No. 279-390, not
supplied) and a standard wall plate for
this mounting method.
1. Plug one end of the short modular
cord into the TEL. LINE jack on the
back of the base.
Follow these steps when you place the
base on a desk, shelf, or table.
1. Plug one end of the supplied modular cord into the TEL. LINE jack
on the back of the base.
2. Plug the modular cord’s other end
into a modular phone line jack.
3. Insert the supplied AC adapter’s
barrel plug into the 12VDC jack on
the back of the base.
4. Plug the adapter into a standard
AC outlet.
6
2. Route the short cord downward
through the slot on the base’s bottom and under the clips as shown.
43-1031.fm Page 7 Tuesday, August 17, 1999 9:24 AM
3. Route the other end of the short
cord through the hole in the
bracket’s center.
7. Align the bracket’s keyhole slots
with the wall plate studs and slide
the base downward to secure it.
4. Attach the supplied bracket to the
bottom of the base by inserting
the tabs on the bracket into the
slots on the base, then sliding the
bracket up.
8. Carefully place the handset in the
cradle at the top of the base and
make sure it is secure.
5. Insert the supplied AC adapter’s
barrel plug into the 12VDC jack on
the back of the base. Then plug
the adapter into a standard AC
outlet.
Note: If you later want to mount
the base on a desktop, press
PUSH on the bracket and pull it off
to remove it.
9. Fully extend the base’s antenna
and place it in a vertical position.
Mounting the Base Directly
on the Wall
You need two wood screws (not supplied) for this mounting method.
6. Plug the modular cord into the
wall plate’s jack.
1. Drill two holes 315/16 inches apart.
Then thread a screw into each
hole, letting the heads extend 1/4
inch from the wall.
7
43-1031.fm Page 8 Tuesday, August 17, 1999 9:24 AM
2. Plug one end of the supplied modular cord into the TEL. LINE jack
on the back of the base.
6. Plug the modular cord into a modular phone line jack.
3. On the bottom of the base, route
the modular cord downward and
under the slot’s clips as shown.
7. Align the keyhole slots with the
mounting screws and slide the
base downward to secure it.
4. Attach the supplied bracket to the
bottom of the base by inserting
the tabs on the bracket into the
slots on the base, then sliding the
bracket up.
8. Carefully place the handset in the
cradle at the top of the base and
make sure it is secure.
Note: If you later want to mount
the base on a desktop, press
PUSH on the bracket and pull it off
to remove it from the base’s bottom.
5. Insert the supplied AC adapter’s
barrel plug into the 12VDC jack on
the back of the base. Then plug
the adapter into a standard AC
outlet.
8
9. Fully extend the base’s antenna
and place it in a vertical position.
43-1031.fm Page 9 Tuesday, August 17, 1999 9:24 AM
CHARGING THE
BATTERY
Before you use your phone for the first
time or when you install a new battery,
make sure RINGER ON/OFF on the
handset is set to OFF, then charge the
battery for about 12-15 hours by placing the handset on the cradle so the
POWER and CHARGE indicators
light.
The phone charges whenever the
handset is on the base. You can recharge the battery at any time, but be
sure to recharge it when BATT LOW
lights on the handset.
Notes:
• Continuing to use the battery after
BATT LOW lights could shorten
overall battery life.
• The first time you use your phone
after installing a new battery, the
handset might not work or might
sound an error tone when you
press TALK. This might also occur
when you recharge a battery that
has been completely discharged.
• If the CHARGE indicator does not
light when you place the handset
on the cradle, be sure the battery
is connected to the pins inside the
battery compartment, and the AC
adapter is securely connected to
the base.
Also, check the charging contacts
on the handset and base. If the
contacts are dirty or tarnished,
gently clean them with a pencil
eraser.
• About once a month, fully discharge the battery. Keep the
handset off the cradle until BATT
LOW lights. Then return the handset to the cradle and recharge the
battery for about 10 hours.
SETTING THE DIALING
MODE
Set TONE/PULSE on the base for the
type of service you have. If you are not
sure which type you have, do this test.
1. Set TONE/PULSE to TONE.
If this happens, be sure RINGER
ON/OFF is set to ON. Then return
the handset to the cradle for 5
seconds. This resets the security
access code.
9
43-1031.fm Page 10 Tuesday, August 17, 1999 9:24 AM
2. Lift the handset, press TALK, and
listen for a dial tone.
SETTING THE RINGER
ON/OFF
3. Press any number other than 0.
If the dial tone stops, you have touchtone service. Leave TONE/PULSE set
to TONE.
To turn off the ringer, set RINGER ON/
OFF on the handset to OFF. To turn on
the ringer, set it to ON.
If the dial tone continues, you have
pulse (rotary) service. Set TONE/
PULSE to PULSE.
Note: With the handset’s ringer off,
you can still make and receive calls using the cordless phone. Telephones on
the same line still ring when there is an
incoming call, the handset’s IN USE indicator flashes, and the POWER and
CHARGE indicators on the base flash
until you answer the call.
10
43-1031.fm Page 11 Tuesday, August 17, 1999 9:24 AM
OPERATION
To disconnect a call, replace the handset on the base.
Before using your cordless telephone,
you must install and charge its battery
(see “Installing the Battery” and
“Charging the Battery”). For the best
operation, make sure the base’s antenna is fully extended.
Using the Handset Away from
the Base
MAKING/ANSWERING A
CALL
To use the handset away from the
base, press TALK to make or answer a
call. The IN USE indicator on the handset lights.
You can use your cordless telephone
in two ways: at the base or away from
the base.
To disconnect a call, press TALK so
the IN USE indicator on the handset
turns off.
Using the Handset at the
Base
Notes:
You can use the handset at the base
like a regular corded telephone. Place
the handset in the cradle. The base
rings whether RINGER ON/OFF on the
handset is set to ON or OFF.
To answer a call, just lift the handset
from the base.
• Press TALK so the IN USE indicator turns off when you are not
making or answering a call, to
conserve battery power and leave
the phone line available.
• You can make or answer a call on
another phone on the same
phone line, even if the handset is
away from the base.
To make a call, lift the handset from
the base and press TALK so the IN
USE indicator lights.
11
43-1031.fm Page 12 Tuesday, August 17, 1999 9:24 AM
REDUCING
INTERFERENCE
To reduce interference between the
handset and the base, press CHANNEL
to switch to the next channel (10 in all)
until you receive the best reception.
REDIAL
USING FLASH
Use FLASH on the handset to perform
the switchhook operation for special
services, such as call waiting.
For example, if you have call waiting,
press FLASH to take an incoming call
without disconnecting the current call.
Press FLASH again to return to the first
call.
To quickly redial the last number dialed, simply lift the handset from the
cradle or press TALK so the IN USE indicator lights. Then press REDIAL.
Notes:
Note: We recommend you not use REDIAL to dial numbers that include a
TONE entry (see “Using Tone Services
with a Service Number”).
12
• If you do not have a special phone
service, pressing FLASH might
disconnect the current call.
• The redial memory does not store
a FLASH entry or any digits
entered after you press FLASH.
43-1031.fm Page 13 Tuesday, August 17, 1999 9:24 AM
USING TONE SERVICES
WITH A SERVICE
NUMBER
Some special services, such as bank
by phone, require tone signals. If you
have pulse service, you can still use
these special tone services by following these steps.
USING PAGE
PAGE lets you locate the handset if you
misplaced it, or alert the person holding the handset. The handset sounds
four beeps when someone presses
PAGE on the base. The IN USE indicator and the selected channel appear on
the base’s display.
1. Set TONE/PULSE on the base to
PULSE.
Note: The handset will not beep during
a call, or if the ringer is off.
2. Dial the service’s main number.
3. When the service answers, press
(S). Then dial the additional numbers. The phone sends these
numbers as tone signals.
4. When you complete the call, place
the handset on the cradle or press
TALK to disconnect the call. The
phone automatically resets to the
pulse mode.
Note: We recommend you not use REDIAL to dial numbers that include a
TONE entry.
13
43-1031.fm Page 14 Tuesday, August 17, 1999 9:24 AM
MEMORY DIALING
4. Press MEMORY again.
You can store up to 10 phone numbers
for single-button dialing. Each stored
number can be up to 16 digits long.
5. Press the memory location number (0 to 9) where you want to
store the number. A long beep
sounds. The phone number is
now stored in memory.
Notes:
• If TONE/PULSE is set to PULSE
and you want to use tone dialing
for a memory number, you must
store the tone entry (S) along with
the number.
• To keep your accounts secure, we
recommend you not store your
personal access code for services
such as bank-by-phone in a memory location.
6. Remove the plastic covering from
the handset’s index card with a
small pointed object, such as the
end of a straightened paper clip.
Write the person’s or company’s
name and memory location number on the card in pencil (in case
you want to change it later).
7. Repeat Steps 2-6 to store and
record other telephone numbers.
Notes:
Storing a Number in Memory
1. If necessary, press TALK on the
handset so the IN USE indicator
turns off.
2. Press MEMORY.
Note: While you are storing a
number in memory, if you do not
press any button within 10 seconds, you must repeat Step 2 and
try again.
3. Dial the number you want to store.
14
• If you receive a call while you are
storing a number in memory,
press TALK to answer the call.
After the call, begin again at Step
1 to store the number.
• To change a phone number stored
in memory, simply store a new
phone number in that position.
• To clear a memory position so no
number is stored in it, press MEMORY twice, then press the memory
location number. A long beep
sounds. The phone number is
now cleared from memory.
Note: A fast beeping pattern indicates
that your clearing was unsuccessful.
Try the process again.
43-1031.fm Page 15 Tuesday, August 17, 1999 9:24 AM
Entering a Pause in a Memory
Number
Chain Dialing Service
Numbers
In some telephone systems, you must
dial an access code (9, for example)
and wait for a second dial tone before
you can dial an outside number. If your
phone is connected to one of these
systems, you might want to enter a
pause at the appropriate point when
you store a phone number in memory.
When calling special services (such as
alternate long distance or bank by
phone), dial the service’s main number
first. Then, at the appropriate place in
the call, press MEMORY and the number for the location where the additional information is stored.
When storing a number, press PAUSE
to enter a 3-second pause. For a longer pause, press PAUSE again (each
press enters a 3-second pause).
Testing Stored Emergency
Numbers
If you store an emergency service’s
number (police department, fire department, ambulance) and you choose
to test the stored number, make the
test call during the late evening or early
morning hours to avoid peak demand
periods. Also, remain on the line to explain the reason for your call.
Dialing a Stored Number
Follow these steps to dial a number
stored in memory.
• Lift the handset from the cradle
and press TALK so the IN USE
indicator lights.
• When you hear a dial tone, press
MEMORY and then press the
memory location number where
the phone number is stored. The
phone dials the stored number.
15
43-1031.fm Page 16 Tuesday, August 17, 1999 9:24 AM
TROUBLESHOOTING
We do not expect you to have any problems with your telephone, but if you do, these
suggestions might help. If you still have problems, check other phones on the same
line to see if they work properly. If they do and the problem does not seem to be with
your phone service, take your phone to your local Radio Shack store for assistance.
Problem
The handset does not
work.
Solution
• Press TALK on the handset.
• Move the handset closer to the base.
• Be sure the phone line cord and AC adapter
are correctly and securely connected.
• Be sure the battery is charged.
• Fully extend the base’s antenna vertically.
• Return the handset to the cradle for 5 seconds, and then try again.
• Check the handset and base’s charging contacts. If they are dirty, clean them with a pencil
eraser.
Volume drops or you hear
unusual sounds on the
line.
Call is noisy.
Someone has picked up another phone on the
same line. Hang up the other phone.
• Press CHANNEL to switch to another channel.
• Do not mount the base near appliances or
large metal objects.
• Hang up and redial the number.
• Keep the handset away from interference
sources such as computers; remote control
toys; wireless microphones, alarm systems,
intercoms and room monitors; fluorescent
lights; and electrical appliances. If the interference is severe, turn off the interfering device.
• Fully extend the base’s antenna vertically.
16
43-1031.fm Page 17 Tuesday, August 17, 1999 9:24 AM
Problem
The handset’s range
decreases.
Solution
• Fully extend the base’s antenna vertically.
• Be sure the antenna is not touching a metal
surface.
• Return the handset to the cradle, and recharge
the battery.
Receiver sound flutters or
fades.
• Be sure the battery is charged.
• Fully extend the base’s antenna vertically.
• Be sure the battery is charged.
• Move the handset closer to the base.
Can make calls, but telephone does not ring.
• Handset’s RINGER must be set to ON to ring.
Can receive calls, but cannot make calls.
Set the TONE/PULSE switch correctly for the type of
service.
You cannot answer/make a
call and the handset
sounds an error tone when
you lift it from the base or
press TALK.
The phone might be receiving interference from another RF signal; or, if the handset is away from the
base during a long period of AC power failure, the
phone might lose its access protection code. Return the handset to the base for a few seconds.
• Telephone company might be using unusual
ringing methods. Your telephone is designed
for standard straight line bridged ringing.
17
43-1031.fm Page 18 Tuesday, August 17, 1999 9:24 AM
CARE AND MAINTENANCE
Your Radio Shack ET-531 10-Channel Cordless Telephone with 10-Memory Speed
Dialing is an example of superior design and craftsmanship. The following suggestions will help you care for your phones so you can enjoy it for years.
Keep the phone dry. If it gets wet, wipe it dry immediately. Liquids can
contain minerals that corrode the electronic circuits.
Handle the phone gently and carefully. Dropping it can damage circuit boards and cases and cause the phone to work improperly.
Use and store the phone only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices and
distort or melt plastic parts.
Keep the phone away from dust and dirt which can cause premature
wear of parts.
CLEANER
Wipe the phone with a damp cloth occasionally to keep it looking
new. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean your phone.
Modifying or tampering with the phone’s internal components can cause a malfunction and might invalidate its warranty and void your FCC authorization to operate it.
If your phone is not performing as it should, take it to your local Radio Shack store
for assistance. If the trouble is affecting the phone lines, the phone company might
ask you to disconnect your phone until you have resolved the problem.
18
43-1031.fm Page 19 Tuesday, August 17, 1999 9:24 AM
REPLACING THE
BATTERY
If you follow the instructions in “Charging the Battery,” the supplied battery
should last about one year. When the
battery loses its ability to fully charge,
order a 3.6 volt, 300 milliamp battery
with a connector that fits the connector
in the battery compartment. You can
order a replacement battery through
your local Radio Shack store.
Install the new battery as described
below, then charge the battery (see
“Charging the Battery”).
1. Slide off the battery compartment
cover on the back of the handset
as shown.
2. Gently pull on the battery wires to
disconnect the plug, then remove
the battery.
3. Insert a fresh battery and connect
its plug to the pins inside the battery compartment.
4. Replace the cover.
Caution: Your telephone contains a
rechargeable nickel cadmium battery.
At the end of the battery’s useful life, it
must be recycled or disposed of properly. Contact your local, county, or
state hazardous waste management
authorities for information on recycling
or disposal programs in your area.
Some options that might be available
are: municipal curb-side collection,
drop off boxes at retailers, recycling
collection centers, and mail back programs.
THE FCC WANTS YOU
TO KNOW
In the unlikely event that your phone
causes problems on the phone line,
the phone company can temporarily
discontinue your service. If this happens, the phone company attempts to
notify you in advance. If advance notice is not practical, the phone company notifies you as soon as possible and
advises you of your right to file a complaint with the FCC.
Also, the phone company can make
changes to its lines, equipment, operations, or procedures that could affect
the operation of the phone. The phone
company notifies you of these changes
in advance, so you can take the necessary steps to prevent interruption of
your phone service.
19
43-1031.fm Page 20 Tuesday, August 17, 1999 9:24 AM
Your phone might cause TV or radio
interference even when it is operating
properly. To determine whether your
phone is causing the interference, turn
off your phone. If the interference goes
away, your phone is causing the interference. Try to eliminate the interference by:
• Moving your phone away from the
receiver
• Connecting your phone to an AC
outlet that is on a different electrical circuit from the receiver
• Contacting your local
Shack store for help
Radio
LIGHTNING
Your phone has built-in protection circuits to reduce the risk of damage from
surges in phone line current. These
protection circuits meet or exceed FCC
requirements. However, lightning striking the phone lines can damage your
phone.
Lighting damage is not common. Nevertheless, if you live an area that has
severe electrical storms, we suggest
that you unplug your phone during
storms to reduce the possibility of
damage.
If you cannot eliminate the interference, the FCC requires that you stop
using your phone.
RADIO SHACK LIMITED WARRANTY
This telephone product is warranted against manufacturing defects in material and workmanship for one (1) year
from the date of purchase from Radio Shack company owned stores and authorized Radio Shack franchisees and
dealers. Within this period bring your Radio Shack sales slip as proof-of-purchase date to any Radio Shack
store.
This warranty does not cover damage or failure caused by or attributable to Acts of God, abuse, misuse, improper
or abnormal usage, faulty installation, improper maintenance, lightning or other incidence of excess voltage, or
any repairs other than those provided by a Radio Shack Authorized Service Facility, or transportation costs. Radio
Shack is not responsible or liable for indirect, special, or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to loss of property,
loss of revenue or profit, or costs of removal, installation or reinstallation.
EXCEPT AS PROVIDED HEREIN, RADIO SHACK MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED
WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES
CONTAINED HEREIN. Some states do not allow the limitation or exclusion of incidental or consequential damages and some states do not allow limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser. There will be charges rendered for repairs to the product
made after the expiration of the aforesaid one (1) year warranty period.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
We Service What We Sell
9/94
RADIO SHACK
A Division of Tandy Corporation
Fort Worth, Texas 76102
8A5
Printed in Hong Kong
Download PDF