FIMCO LG-25 P, SS Lawn & Garden Spot Sprayer ASSEMBLY / OPERATION INSTRUCTIONS / PARTS

Below you will find brief information for Lawn & Garden Spot Sprayer LG-25-P, Lawn & Garden Spot Sprayer LG-25-SS. This instruction manual will help you to understand the basic set up, operation and maintenance of your sprayer. The sprayer has a 25 gallon tank and is equipped with a 12 volt diaphragm pump with a pressure switch that is factory set at a maximum of 60 psi. The sprayer has an adjustable nozzle that allows the spray to be adjusted from a cone shaped fine mist to a straight stream.

PDF Download

Document

5301146
MODEL NO. LG-25-P
5301147
MODEL NO. LG-25-SS
25 Gallon Lawn &amp; Garden Spot Sprayers
ASSEMBLY / OPERATION INSTRUCTIONS / PARTS
GENERAL INFORMATION
The purpose of this manual is to assist you in operating and
maintaining your lawn and garden sprayer. Please read it
carefully as it furnishes information which will help you
achieve years of dependable trouble free operation.
WARRANTY / PARTS / SERVICE
Products are warranted for one year from date of purchase
against manufacturer or workmanship defects.
Your authorized dealer is the best source of replacement
parts and service. To obtain prompt, efficient service, always
remember to give the following information:
1. Correct part description and part number.
2. Model Number of your sprayer.
3. Serial Number of your sprayer.
Part description and part numbers can be obtained from the
illustrated parts list section of this manual.
Whenever you need parts or repair service, contact your
distributor / dealer first. For warranty work always take your
original sales slip, or other evidence of purchase date, to your
distributor / dealer.
CAUTION: Always check the vehicle load rating before using
this sprayer. The loaded weight of the sprayer and boom
assembly is about 170 lbs. when the tank is full for a 15 gallon
unit and 250 lbs. for a 25 gallon unit.
It is important to test the sprayer with plain water before actual
spraying is attempted. This will enable you to check the
sprayer for leaks in the plumbing system.
ASSEMBLY
The sprayer is assembled at the factory, and the only assembly necessary is to hook up the wiring to an existing 12 volt
power source. The red wire of the two wire set must be
connected to the positive post on the battery or the “Hot”
connection on a switch or to the ammeter. The dark wire may
be grounded or connected to the negative battery post.
The pressure gauge is shipped in a parts bag located in the
tank. Thread the gauge into the open port of the tee fitting
which is located near the pump outlet port. Use thread sealant
on the gauge threads.
OPERATION
The pump on the sprayer is equipped with a pressure switch
that is factory set at a maximum of 60 PSI. Pressure may be
decreased by opening the regulating valve. The more it is
opened, the lower the pressure will be.
TECHNICAL SPECIFICATIONS
• Corrosion Resistant Polyethylene Tank.
• 12 Volt Diaphragm Pump.
• Pressure Gauge-Adjustable Pressure Range.
• 15 Foot Handgun Hose.
W W W. F I M C O I N D U S T R I E S . C O M
1000 FIMCO LANE • P.O. BOX 1700 • NO. SIOUX CITY, SD 57049
TOLL FREE: 800-831-0027 • TOLL FREE FAX: 800-494-0440
Form No. 1083
(5004689 5/06)
Printed In U.S.A.
Page 1
The handgun has an adjustable nozzle which allows the
spray to be adjusted from a cone shaped fine mist to a straight
stream. It is normal for the pump to cycle when spraying with
a fine mist spray.
Regularly clean the strainer which is located on the bottom of
the intake tube. Remove the strainer from the tube and clean
with water.
WARNING: Some chemicals will damage the pump valves if
allowed to soak untreated for a length of time. Always flush
the pump with water after use. Do not allow chemicals to sit
in pump for extended times of idleness. Follow the chemical
manufactures instructions on disposal of all waste water from
the sprayer.
AFTER SPRAYING
After use fill the sprayer part way with water, start the sprayer
and allow clear water to be pumped through the plumbing
Page 2
system and out through the handgun. Use the handgun on
the sprayer to thoroughly wash all internal parts of the tank
and tank cover.
Refill the tank about half full with plain water and use a
chemical neutralizer such as Nutra-Sol or equivalent and
repeat cleaning instructions above. Flush the entire sprayer
with the neutralizing agent. Follow the chemical manufacturers disposal instructions of all wash or rinsing water.
WINTER STORAGE
Drain all water out of sprayer paying special attention to
pump, valves, and handgun. These items are especially
prone to damage from chemicals and freezing weather.
The sprayer should be winterized before storage by pumping a solution of R.V. anti-freeze through the entire plumbing.
Proper care and maintenance will prolong the life of the
sprayer.
Page 3
Page 4
">

Hello! I am an AI chatbot specifically trained to assist you with the LG-25 P SS Lawn & Garden Spot Sprayer ASSEMBLY / OPERATION INSTRUCTIONS / PARTS. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key features

25 Gallon Tank
12 Volt Diaphragm Pump
Pressure Gauge-Adjustable Pressure Range
15 Foot Handgun Hose
Adjustable Nozzle
Corrosion Resistant Polyethylene Tank

Frequently asked questions

The pump on the sprayer is equipped with a pressure switch that is factory set at a maximum of 60 PSI. Pressure may be decreased by opening the regulating valve. The more it is opened, the lower the pressure will be.

The sprayer should be winterized before storage by pumping a solution of R.V. anti-freeze through the entire plumbing.

After use fill the sprayer part way with water, start the sprayer and allow clear water to be pumped through the plumbing system and out through the handgun. Use the handgun on the sprayer to thoroughly wash all internal parts of the tank and tank cover. Refill the tank about half full with plain water and use a chemical neutralizer such as Nutra-Sol or equivalent and repeat cleaning instructions above. Flush the entire sprayer with the neutralizing agent. Follow the chemical manufacturers disposal instructions of all wash or rinsing water.