fingerprint door lock
QUICK START GUIDE FOR F7
QUICK START GUIDE FOR F7
Items included when your package arrives;
•
•
•
Fingerprint terminal (F7).
Screwdriver Tool
Quick start Guide
Important Notes
•
•
•
•
Do not place the F7 outdoors without adequate protection from weather.
Do not place the F7 under strong light.
Use regulated 12V DC 1.5A power source (supplied from door control panel or separately
purchased power supply).
Do not place the F7 in a vulnerable location where it might be subjected to weather, vandalism,
etc.
QUICK START GUIDE FOR F7
Mounting the Unit
•
•
•
•
•
•
Locate the appropriate area for the unit. Place the unit approximately 5 ½ feet above
the ground level so that the users are comfortable in using the unit with fewer chances
of errors.
Create conduits for the power and network cable on the wall so that the unit receives
the connections from the back of the wall.
Remove the screw at the bottom of the unit when held vertically as shown in the
picture below:
This will remove the back plate of the unit.
Install the back plate of the unit on to the wall and connect the power and network
cables from behind the back plate.
Secure the front of the unit on the back plate by reinstalling the removed screw from
the bottom of the unit earlier.
Hardware Setup
•
Power on the unit by supplying 12V DC to the PWR and GND pins on the back of the unit.
The power supply is not supplied with the unit. Please make sure that the power requirements
are strictly met to avoid permanent damage to the unit.
12V DC
Power
supply
GND
+12V
Power
Lock
COM
Lock NO
Lock NC
GND
Alarm+
Alarm—
Button
GND
Bell+
Bell—
•
GND
RS232
RXD
RS232
TXD
GND
RS485 A
RS485 B
GND
DATA0
DATA1
+5V
Output
Door
Sensor
GND
After the Power on self test the ACT FP will show the date, day and time.
QUICK START GUIDE FOR F7
Date and Time Setup
To change the date and time, press the M (Menu) key;
.
The Menu will then display.
Menu
User Manage
Scroll with the ▲/▼ keys and place the cursor ( ) alongside “Options”. Press the OK key.
Scroll with the ▲/▼ keys and place the cursor ( ) alongside “System Opt”. Press the OK key.
Scroll with the ▲/▼ keys and place the cursor ( ) alongside “Date Time”. Press the OK key.
Once in the YYYY-MM-DD 24H screen, use the scroll ▲/▼ keys to move between data fields.
Set the date and time.
Press the OK key to accept changes.
Press the C (cancel) key to cancel changes.
QUICK START GUIDE FOR F7
Fingerprint Enrollment:
Users (not including Admins, Supervisors or Enrollers) have NO “administrative” access to the F7, but
can gain door access and have his/her attendance recorded.
Note:
Until an actual “Administrator” is enrolled in the F7, ALL “users” enrolled on the F7 have
“temporarily” have administrative access. Therefore it is important to enroll an “administrator”
on the F7 soon after initial installation.
“Users” can enroll with three methods;
•
•
•
Fingerprints
Passwords
Fingerprints and Passwords
Enroll Fingerprint (for Users)
To start Fingerprint enrollment, press the M (Menu) key on the F7.
Scroll with the ▲/▼ keys and place the cursor ( ) alongside “User Manage”
Menu
▼
►User Manage
Options
PenDrive Mng
QUICK START GUIDE FOR F7
Press the OK key.
Scroll with the ▲/▼ keys and place the cursor ( ) alongside “Enroll User”.
User Manage
▼
►Enroll User
FPCard Mng
Enroll Admin
Press the OK key.
Scroll with the ▲/▼ keys and place the cursor ( ) alongside “Enroll FP”.
Enroll User
►Enroll FP
Enroll Pwd
FP & Pwd
▼
Press the OK key.
The F7 will prompt you;
Enroll FP
New Enroll?
ESC
OK
If this is a NEW User, then press OK
The F7 will then prompt you with the next available User ID
New Enroll
UserID 00001-0
ESC
OK
QUICK START GUIDE FOR F7
If no user has yet been enrolled on the F7, the next available User ID# will be 00001.
Press the OK key to accept 00001, or manually key in a different number if desired.
The F7 will then prompt;
New Enroll
00001-0
Place Finger . . .
ESC/Exit
Remember the rules for proper finger placement;
The user’s finger should completely cover the sensor. The finger should be placed flat and in the
center of the sensor. The finger should cover at least 80% of the sensor as shown below:
The finger should NOT be placed in the following positions:
QUICK START GUIDE FOR F7
Place your finger on the sensor for a full 2 seconds.
After the F7 scans your fingerprint successfully, it will “beep” and then prompt you briefly with;
New Enroll
00001-1
Remove Finger
ESC/Exit
Then you’ll be prompted;
New Enroll
00001-1
Second Press
ESC/Exit
Remove your finger, and then place your finger on the sensor a 2nd time. Again, you’ll be prompted
briefly;
New Enroll
00001-1
Remove Finger
ESC/Exit
Remove your finger, and then place your finger on the sensor a 3rd and final time. You’ll then be
prompted;
New Enroll
00001-0
ESC
OK (Save)
Press the OK key to accept the newly enrolled finger.
UserID 0001 has now been successfully enrolled with one fingerprint.
QUICK START GUIDE FOR F7
The F7 will then prompt you with;
New Enroll
Continue?
ESC
OK
If you wish to continue enrolling additional users, press the OK key and follow the same procedures.
If you’re finished enrolling additional users, press the C (Cancel/ESC) key.
When pressing C (Cancel/ESC) key, the F7 will prompt you;
Backup Enroll
Continue?
UserID 0001
ESC
OK
If you wish to add a “backup finger” for UserID 00001 press the OK key.
Note:
Ideally, we recommend enrolling two fingers of each hand so that in case of injury of one hand the
user can use the finger of the other hand as a backup. It is recommended to enroll left or right
index finger and left middle or right middle fingers.
After enrolling one or more fingerprints to UserID 00001 press the C (Cancel/ESC) key.
You’ll note pressing the C (Cancel/ESC) key takes you back to the previous menu;
Enroll User
►Enroll FP
Enroll Pwd
FP & Pwd
▼
Press C (Cancel/ESC)
User Manage
►Enroll User
FPCard Mng
Enroll Admin
▼
Press C (Cancel/ESC)
Menu
▼
►User Manage
Options
PenDrive Mng
QUICK START GUIDE FOR F7
Continue pressing the C (Cancel/ESC) key until you return to the Start-Up window;
Welcome Check-In
HH:MM
MM/DD/YY DAY
Note:
The actual current date/time will appear.
Test the newly enrolled fingerprint by having UserID 0001 place his/her finger on the sensor.
If successful, the F7 will prompt with an audible “Thank you”, and the screen will display;
Verify
Pin: 00001
Verified.
Note:
The F7 will make a note in its transaction log that User ID 0001 accessed the F7. This
information can be used for Time & Attendance software applications and/or for door access.
Note:
If the fingerprints of certain users are unable to be enrolled successfully, you may use the Enroll
Pwd (instead of Enroll FP) option for those users.
This will allow the user to choose a password/PIN# (up to 4 digits) instead of his/her fingerprint
(similar to how a cash machine/ATM works).
Once all the users are enrolled, it’s advised to enroll a system Administrator.
Once an Administrator is enrolled, normal users will no longer be able to access the Menu and
make unauthorized changes.
The enrollment procedure for Admin(s) is the same as for user(s). But instead of selecting Enroll
User, scroll down and select Enroll Admin, instead.
Press the M (Menu) key to begin;
Scroll with the ▲/▼ keys and place the cursor ( ) alongside “User Manage”. Press OK.
Scroll with the ▲/▼ keys and place the cursor ( ) alongside “Enroll Admin”. Press OK.
Scroll with the ▲/▼ keys and place the cursor ( ) alongside “Enroll FP”. Press OK
Press OK to accept the default User ID, or manually enter a preferred User ID and press OK
QUICK START GUIDE FOR F7
Remove Enrolled User
Press the M (Menu) key to begin;
Scroll with the ▲/▼ keys and place the cursor ( ) alongside “User Manage”. Press OK.
Scroll with the ▲/▼ keys and place the cursor ( ) alongside “Delete”. Press OK.
Enter the User ID of the user you wish to delete. Press OK
The F7 will prompt you to confirm you wish to delete the fingerprint(s). Press OK
The F7 will prompt you to confirm you wish to delete the User. Press OK
The F7 will prompt you to confirm you wish to delete the User again. Press OK
Set Communications Options:
Press the M (Menu) key to begin
Scroll with the ▲/▼ keys and place the cursor ( ) alongside “Options”. Press OK.
Scroll with the ▲/▼ keys and place the cursor ( ) alongside “Comm Opt”. Press OK.
Available communication options will display;
•
•
•
•
•
•
•
•
•
IP Address
NetMask
Gateway
Net Speed
Baud Rate
Dev Num
RS232
RS 485
COMM Key
Scroll with the ▲/▼ keys and place the cursor ( ) alongside the desired Comm option.
Press OK.
Enter additional Communication settings, each time pressing OK to accept.
QUICK START GUIDE FOR F7
Note:
Set the Dev num as 1
If you have more than one terminal being installed, make sure each terminal has a
unique device number.
Set the IP Addr for the F7 if you are using TCP/IP connectivity.
Record the IP address of each F7 you’ve installed.
These IP addresses are used to identify the F7s.
If using Serial communication then match the F7’s Baud Rate with the serial port of the
connecting computer.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement