Vitek | VTM-LCD194P | Instruction manual | Vitek VTM-LCD194P Instruction manual

VTC-IRE30/2810
Day/Night IR Bullet Camera
with 100’ Range
VITEK
• High Density 1/3” Sony EX-VIEW CCD & Effio-E DSP
• 700 TV Lines of Resolution
• Advanced IR Optimizer helps reduce over saturation of IR illuminated video without
engaging the Image Signal Processor chip
• E-WDR by Adaptive Tone Reproduction
• 30 850nm Infrared LEDs with up to 100’ Range
• 0.003 Lux (F1.2 @ 40IRE) / 0 Lux with IR LEDs On
• IR Corrected 2.8-10mm Varifocal DC Auto Iris IR Lens
• 2DNR Noise Reduction
• Motion Detection, Privacy Masking & Highlight Masking
• OSD (On Screen Display) menu and Camera ID
• IP-66 Rated Water Resistance
• Heavy Duty Mount with Cable Feed Through
• 24VAC/12VDC Dual Voltage
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
This symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the unit.
This symbol is intended to alert the user to the presence of
uninsulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock.
Caution
To prevent electric shocks
and risk of fire hazards, do
NOT use other than specified
power source.
Warning (NTSC version) -- This equipment has been tested and found to comply with the limits for a
Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation
of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at their own expense.
Caution -- Any changes or modifications in construction of this device that are not approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Notice -- The images used in this manual are processed to help comprehension
and may differ from the actual video of the camera.
WARNING
NEVER USE THIS CAMERA IN WATER.
2
1. Safety Instructions and Notes
• Please read these safety and operating instructions before putting the camera into operation.
• Keep the manual in a safe place for later reference.
• Pay attention to safety when laying the connection cable and observe that the cable is not subjected to
heavy loads, kinks, damage or moisture.
• Never open the device to expose boards or lenses.
The warranty becomes void if repairs are undertaken by unauthorized persons.
• Only authorized service centers may perform maintenance or repairs.
• Use only a mild detergent to clean the housing.
• Keep the window surface clean of dirt or dust, which may reflect infrared light into the lens at night.
• The camera should never be operated beyond the technical specifications. This can lead to destruction.
2. General Descriptions
This camera is an ultra clear resolution camera that realizes over 700TVL resolution and a crisp color
reproduction with Sony 960H EX-view CCD and Effio-E image signal processor.
Effio-E digital imaging system:
• Delivers crystal clear images with over 700TVL resolution that accurately captures every aspect of
any scene
• Color signal processing provides optimum balance between luminance and chroma signals for
high color reproducibility, even for the detail scene which contains very high spatial frequency
• Incorporates 2-D noise reduction signal processing
24VAC/12VDC dual power design:
• Offers flexibility of installation
• Ensures reliability
Main features:
• High Density 1/3" Sony EX-view CCD (960H)
• Resolution 700 Horizontal Lines
• E-WDR by ATR (Adaptive Tone Reproduction)
• 2-D noise reduction
• Motion Detection
• Privacy Mask function
• OSD menu and camera ID
• Switches to B/W and able to accept the infrared spectrum at night mode
• Very low noise and superior picture quality
• Sensitivity of 0.003Lux (F1.2@40IRE)
• Automatic White Balance (ATW)
• Support C/CS mount DC Drive auto iris lens
• Supply voltage: 24Vac/12Vdc Dual voltage
3
3. Supplied Items
①
②
③
④
⑤
1 x Weatherproof D & N Bullet Camera
3 x Mounting screws
3 x anchors
1 x 2.5mm L-Wrench
1 x Installation and Operating Instructions
②
③
④
4. Part names
4.1 External (Below model is only used for understanding. Color or Design can be different.)
ⓐ
ⓑ
ⓒⓓ
ⓔ
ⓕ ⓖ ⓗ ⓘ
ⓐ
ⓑ
ⓒ
ⓓ
ⓔ
ⓕ
ⓖ
ⓗ
ⓘ
ⓙ
ⓙ
Glass Window
Sunshield
Thumb screw for Sunshield
Lens/IR LED Access Cover
Camera Body
Mount Rotation Adjustment
Mount Tilt Adjustment
Mount Pan Adjustment
Mounting bracket
Rubber gasket
4.2 Internal
ⓚ
ⓛ
ⓜ
ⓝ
ⓚ
ⓛ
ⓜ
ⓝ
Infrared LEDs (X30)
Lens Hood
OSD board
Focus Ring
ⓞ Zoom Knob
ⓞ
4
5. Installation Instructions
• Make sure the power is not applied before the installation.
• Once the camera is installed, you may first connect the low voltage (AC24V or DC12V) wire to the
camera power connector, then plug the AC adapter to the AC outlets to avoid an improper reset from
power jitter and possible damage from voltage surge.
5.1 Mounting the Camera
1) Drill 3 holes into the wall or ceiling using the supplied template
2) Insert the supplied anchors into the drilled holes
3) Route the power/ video cable through the camera mount.
4) Match foot mount holes to the drilled holes
5) Affix the mounting bracket by using supplied screws
6) Adjust the camera direction as below steps.
Direction I: Adjust the camera direction with
ⓗscrew for Pan-direction.
Direction II: Adjust the camera direction with
ⓖscrew for Tilt-direction.
Direction III: Adjust the camera direction with
ⓕscrew for rolling.
5
5.2 Setup of ZOOM and FOCUS
• Adjust zoom and focus in order.
1)
2)
3)
4)
5)
6)
7)
Open ⓓFront cover for adjustment.
Place the separated ⓓFront cover on the safe place from water & dust.
Turn ⓞZoom knob counter clockwise a little to unlock the knob.
Move ⓞZoom knob to fit the zoom. (Wide
Tele)
Turn ⓞZoom knob clockwise a little to lock the knob.
Using thumb and index finger, turn ⓝFocus ring to fit the focus. (Far
Close and tighten ⓓFront cover. (See CAUTION below)
Near)
ⓝ Focus Ring
ⓞ Zoom Knob
3) & 5)
4) & 6)
* IMPORTANT TIP for good focus adjustment
Step 1. Turn Iris Level adjustment VR clockwise to max position.
Step 2. Set ELC switch to ON at DIP switches.
Step 3. Adjust zoom knob and focus ring of lens.
Step 4. Set ELC switch to OFF at DIP switches.
Step 5. Adjust Iris Level VR to get the proper video level.
CAUTION
ⓓ Front cover
When assembling ⓓ Front cover, be sure
that ⓙRubber sealing is not protrusive.
If ⓓ Front cover is tightened excessively,
sealing may not be ensured.
6
5.3 Sunshield
Camera can be protected from the strong sun light by its own Sun shield.
Sunshield must be tightened enough to the body to avoid detaching of it by the wind.
When the sunshield is fixed on camera body, usually
ⓒ Fix screw for Sunshield is located in center of
screw hole.
Adjust the sunshield back or forth according to the
wide or tele position of the lens.
If shades by the sunshield are seen on the image,
reverse the sunshield direction backside to front.
5.4 Power connector
The VTC-IRE30/2810 can operate on either 24AC or 12VDC, dual voltage power.
Polarity free connection is acceptable, but follow the indication if possible.
6. SETUP Menu
6.1 In the menu
Setup menu can be accessed and controlled by OSD control joy stick on the side of the camera.
Five commands are available with the joy stick.
SYMBOL descriptions for joystick operation;
Joy stick
1. ▲,▼,◀,▶ - Denotes the direction of
Joystick lever operation.
2. ● - Denotes pressing down on the
Joystick lever
VIDEO
SUB-OUT
connector
In the menu, use ▲,▼ to move menu, ◀,▶ to change the settings and press ● to select or enter.
The FACTORY DEFAULT in this manual may NOT be the same as the default values
set by the
FACTORY due to feature improvements or customer requirements.
To enter the menu, press ●.
7
6.2 MAIN menu
Follow the chart below for submenu settings.
MAIN Menu-1
MAIN Menu-2
6.2.1 MAIN menu-1
MAIN menu-1
Default
SHUTTER
/AGC
AUTO
Sets the parameters related to the shutter mode and AGC for AUTO and
MANUAL settings. See '6.3 SHUTTER/AGC menu' for details.
LENS
AUTO
Selects the lens type, AUTO or MANUAL. AUTO supports DC auto-iris lens
only. See '6.4 LENS menu' for details.
EXT1
(w/ IR
LED)
DAY/NIGHT
AUTO
(w/o IR
LED)
Descriptions
Can set DAY/NIGHT to AUTO, COLOR, BW, EXT1 and EXT2.
AU TO – Must be used only for a camera with NO IR LEDs.
Camera switches DAY from/to NIGHT automatically along with the
amount of light through the lens..
BURST, DELAY CNT, DAYàNIGHT, NIGHTàDAY can be set.
See ‘DAY/NIGHT menu’ for details.
C OL O R – DAY/NIGHT is disabled and forces to DAY mode only.
BW – DAY/NIGHT is disabled and forces to NIGHT mode only.
Camera switches its IR cut filter out and outputs BW video.
EX T1 – Must be used only for a camera equipped with IR LEDs.
DAY/NIGHT is switched by the external light sensor.
EX T2 – NEVER USE this mode.
Sets MIRROR, BRIGHTNESS, CONTRAST, SHARPNESS, HUE or GAIN.
See '6.6 PICT ADJUST menu' for details.
PICT ADJUST
-
WHITE BAL
ATW
Sets ATW, PUSH, USER1, USER2, ANTI CR, MANUAL or PUSH LOCK.
See '6.7 WHITE BAL menu' for details.
ATR
OFF
Sets ON/OFF for enabling/disabling ATR (Adaptive Tone Reproduction)
compensation for the better dynamic range (E-WDR) of the image.
See '6.8 ATR menu' to adjust the dynamic ranges.
BACKLIGHT
OFF
Selects BACKLIGHT mode out of OFF, HLC or BLC. Areas and gains for
HLC and BLC are factory preset and not user adjustable.
NEXT
Moves to MAIN menu-2.
EXIT
Exits the setup menu. To save the changes, move cursor to 'SAVE ALL'
and press ● button before exiting the setup menu
SAVE ALL
Saves all parameters by pressing ● button when cursor is on 'SAVE ALL'
8
6.2.1 MAIN menu-2
MAIN menu-2
Default
NR
-
MOTION DET
OFF
Sets ON/OFF for enabling/disabling MOTION DET.
See '6.11 MOTION DET menu' for the parameter settings.
PRIVACY
OFF
Sets ON/OFF for enabling/disabling PRIVACY.
See '6.12 PRIVACY menu' for the parameter settings.
LANGUAGE
ENGLISH
CAMERA ID
OFF
CAMERA
RESET
Descriptions
Sets the noise reduction parameters for NR MODE and Y LEVEL,
C LEVEL. See '6.10 NR menu' for details.
Selects the language out of 7 languages.
Sets ON/OFF for enabling/disabling of ID display.
Factory default ID is Software version of camera.
User programmed camera ID will be lost and restored with Factory default
ID by CAMERA RESET. See '6.13 ID menu' for editing ID.
Restores FACTORY DEFAULT.
To save the restored parameters, move cursor to 'SAVE ALL' and press
● button before exiting the setup menu.
BACK
Returns to MAIN menu-1.
EXIT
Exits the setup menu.
To save the changes, move cursor to 'SAVE ALL' and press ● button
before exiting the setup menu
SAVE ALL
Saves all settings by pressing ● button when cursor is on 'SAVEALL'
6.3 SHUTTER/AGC menu
This menu shows how to control/select SHUTTER, AUTO IRIS and AGC to get the optimum image for
high luminance and the low luminance according to the scene.
For example, to reduce the “wash out” and extend the dynamic range for a highlighted scene, you will
use SHUTTER+AUTO IRIS in outdoor daylight. This mode may show color rolling or video level
hunting problems in a certain lighting condition such as fluorescent lights.
For Flickerless mode which reduces flicker by NTSC cameras under 50Hz light or PAL camera under
60Hz light, MAIN>SHUTTER/AGC>MANUAL>SHUTTER must be set to 1/100(NTSC), 1/120(PAL)
and MAIN>SHUTTER/AGC>AUTO>MODE to AUTO IRIS. Normal shutter speed with an auto iris lens
should be set to 1/60(NTSC) and 1/50(PAL) for the optimum sensitivity.
This is a complicated menu so please proceed with care when handling the Shutter.
To enter SHUTTER/AGC menu, press ● button at MAIN menu-1>SHUTTER/AGC.
9
6.3.1 SHUTTER/AGC>AUTO SETUP menu
AUTO SETUP
Default
Descriptions
Sets the shutter mode from AUTO IRIS or SHUT+AUTO IRIS when in
MAIN>LENS>AUTO menu, but it is fixed to SHUT if in the
MAIN>LENS>MANUAL menu.
AU TO IR IS - Light level is controlled by an auto iris lens only.
For proper auto iris operation, the auto iris operation mode in MAIN>
LENS>AUTO>MODE must be set to AUTO.
HIGH
LUMINANCE
MODE
AUTO
IRIS
The shutter speed is fixed to the setting at MAIN>SHUTTER/AGC>
MANUAL>SHUTTER in this mode.
Set SHUTTER to 1/60(NTSC) or 1/50(PAL) for the best sensitivity
unless it is in Flickerless mode.
To set Flickerless mode, MAIN>SHUTTER/AGC>MANUAL>SHUTTER
must be set to 1/100(NTSC), 1/120(PAL) and MAIN>SHUTTER/AGC>
AUTO>MODE to AUTO IRIS.
SH UT+AU TO IR IS- Light level is controlled by the combination of an
auto iris lens and a shutter control to improve the highlight from washout and extend the dynamic range. Shutter speed can vary between
1/60 (1/50) ~ 1/10,000 sec.
This mode can enhance the overall video quality of daylight but may
show a smear in a bright spot light or may show color rolling or video
level hunting under a certain lighting condition such as fluorescent lights.
LOW
LUMINANCE
BRIGHTNESS
032
Adjusts the brightness of the image with an auto iris lens or a shutter
speed control + an auto iris lens.
MODE
AGC
Sets AGC to compensate the video level when the scene is dim.
x0.50
Sets the brightness level which starts AGC from x0.25, x0.50, x0.75 and
x1.0 of full video level.
If set to x0.50, the camera will start AGC when the video level goes
down below the 50% level.
BRIGHTNESS
NOTICE : The setting AUTO IRIS at SHUTTER/AGC>AUTO SETUP>HIGH LUMINANCE MODE will
be changed to SHUT+AUTO IRIS if MAIN menu-1>LENS is changed to MANUAL.
As a result of this, the lens iris can NOT be fully opened when MAIN menu-1>LENS>
AUTO IRIS> MODE is OPEN.
This can be recovered by setting SHUTTER/AGC>AUTO SETUP>HIGH LUMINANCE
MODE to AUTO IRIS.
10
6.3.2 SHUTTER/AGC>MANUAL SETUP menu
MANUAL
SETUP
Default
MODE
SHUT
+AGC
Compensates the video level by the manual shutter control and AGC.
SHUTTER
1/60
(1/50)
Sets the manual shutter to 1/60(1/50), 1/100(1/120), 1/250,1/500,1/1000,
1/2000,1/4000 or 1/10000.
Manual shutter is only useful for scenes where luminance is unchanged.
AGC
6.00
Sets AGC gain in dB. Higher gain compensates brighter but noise
increases.
Manual AGC can be set to 6, 12, 18, 24, 30, 36, 42 or 44.8 dB.
Descriptions
6.4 LENS menu
To enter LENS menu, press ● button at MAIN menu-1>LENS>AUTO.
AUTO IRIS
Default
TYPE
DC
MODE
AUTO
SPEED
080
Descriptions
M U ST B E SE T TO D C ON LY .
This camera does NOT support video type auto iris lens.
AU TO – Lens iris is automatically controlled according to the scene’s
light level.
O PEN – Lens is fully opened regardless of the light level.
C LO SE – Lens is fully closed.
Adjusts the iris control speed.
The lower the value, the faster the speed.
If the speed is too slow or fast, the iris control may be unstable.
11
6.5 DAY/NIGHT menu
To enter DAY/NIGHT menu, press ● button at MAIN menu-1>DAY/NIGHT.
DAY/NIGHT
IR
OPTIMIZER
MODE
LEVEL
Default
Descriptions
OFF
IR OPTIMIZER feature can reduce the over-saturation in video caused by the
narrow emitting IR LEDs
O FF – Disables IR OPTMIZER.
O N – Enables IR OPTIMIZER.
AUTO
There are two modes available by how to manage IR OPTIMIZER.
AU TO – Reducing the over-saturation is automatically adjusted along with the
location of the subject.
C ENTE R – Center area is prioritized to reduce the over-saturation.
Over-saturation in the side area could be ignored.
015
Overall brightness is adjusted when IR OPTIMIZER is working.
High value in LEVEL increases the brightness but the over-saturation could
occur.
Low value in LEVEL decreases the brightness and the dim area could be
darker.
6.6 PICT ADJUST menu
To enter PICT ADJUST menu, press ● button at MAIN menu-1>PICT ADJUST.
12
PICT ADJUST
Default
Descriptions
MIRROR
OFF
Picture will be flipped horizontally if it turns ON.
BRIGHTNESS
000
Increases or decreases the brightness of the picture.
This is different from that of DC iris lens and simply increases or decreases
the digital gain of the video.
Do not increase this too much, the dynamic range for the highlight area will
decrease.
CONTRAST
120
Increases or decreases the contrast of the picture.
SHARPNESS
128
Increases or decreases the sharpness of the picture.
Too much sharpness can make the image appear harsh and will show
more noise. It may also show line flicker at the edge of object in the picture.
HUE
128
Adjusts hue for NTSC version only.
GAIN
128
Increases or decreases the color gain of the picture.
6.7 WHITE BAL menu
White balance can be set to ATW, PUSH, USER1, USER2, ANTI CR, MANUAL or PUSH
LOCK.
ATW (Auto Tracking White balance) and PUSH (Full pull-in) is continuously monitoring/analyzing the
color
temperature of the incoming light and correcting the white balance.
ATW limits the color temperature range to about 2,500˚K~8,500˚K to reduce the excessive compensation
for a large object that has a single color.
PUSH has no limits between about 1,800˚K~10,500˚K, but it may over-compensate the white balance for
a large object that has a single color.
In cases under 2,500˚K such as halogen light, ATW may stop and if so, PUSH mode is recommended.
USER1 and USER2 are a fixed white balance which is user-programmable by R-GAIN and B-GAIN and
useful only for consistent/steady lighting.
ANTI CR (Anti Color Rolling) can reduce color rolling under fluorescent lighting when the camera
operates in shutter control mode without an auto iris lens. (NTSC version only).
MANUAL white balance is a kind of fixed white balance that is user-programmable by B-GAIN, (R-GAIN
will be automatically adjusted in accordance with B-GAIN) and useful only with consistent/steady lighting.
PUSH LOCK is a fixed white balance where the white balance is compensated only while ● button is
pressed at MAIN>WHITE BAL>PUSH LOCK and finishes the white balance when ● button is released.
To enter ATW (MANUAL) menu, press ● button at MAIN menu-1>WHITE BAL>ATW(MANUAL).
13
ATW
Default
Descriptions
SPEED
250
Sets the AWB compensating speed. Lower value makes AWB faster.
C AUTIO N If AWB is too fast, it may produce color oscillation.
DELAY CNT
001
Adjusts the AWB compensation period to next update of AWB.
The smaller value will update AWB more frequently.
ATW FRAME
X2.00
Determines the ATW range with respect to the fundamental range.
A higher value than x1.00 will extend the ATW range at lower and higher
color temperature.
ENVIRONMENT
INDOOR
Selects INDOOR or OUTDOOR.
The ATW is optimized for limited applications.
IN DOOR - Optimized for Indoor installation and it compensates ATW for
low color temperature such as incandescent lights.
O UTD O OR - Optimized for outdoor sunlit applications and compensates
ATW for high color temperature such as daylight.
MANUAL WB
Default
Descriptions
LEVEL
064
Adjusts the manual white balance by LEVEL, where is B-GAIN.
6.8 ATR (Adaptive Tone Reproduction) Menu
The ATR feature improves the dynamic range and the visibility of the image by providing optimal
gradation compensation of the image in one field. This is achieved by two ways of image processing,
luminance compression and contrast enhancement, so that the tone can be enhanced in highlight and
dark areas.
To enter ATR menu, press ● button at MAIN menu-1>ATR.
ATR
Default
Descriptions
LUMINANCE
MID
Compresses the highlight area and enhances the dark area so that the
entire image can converge toward the medium level.
LOW will compensate minimally and HIGH will be level out the image
more. With a HIGH setting, the image may look less contrastive and
noise may increase in the dark area.
CONTRAST
MID
Adjusts the strength of the image contrast.
If set to too high, the dark area may loss detail and the high luminance
area may saturate.14
6.9 BACKLIGHT menu
To enter BACKLIGHT menu, press ● button in MAIN menu-1>BACKLIGHT.
The Backlight Compensation – BLC – function is used to brighten an image in the foreground with a
highly lit area behind it such as sunlight, limiting the affect of silhouetting.
BLC ON
BLC OFF
The Highlight Compensation – HLC – function is used to black out highlighted areas that may blind the
camera, in order to enable a clear visual image of objects, such as the license plates of an oncoming
vehicle or other objects that may be obstructed by headlamps.
HLC ON
HLC OFF
6.10 NR menu
To enter NR menu, press ● button at MAIN menu-2>NR.
15
NR
Default
NR MODE
Y/C
Selects OFF, Y, C or Y/C, which noise reduction is performed with.
006
Indicates the noise reduction strength for the luminance signal.
A higher value performs a stronger noise reduction, which makes the
image less sharp. Due to the limitation of 2D NR, noise reduction may not
be effective enough.
004
Indicates the noise reduction strength for the chrominance signal.
A higher value performs a stronger noise reduction and makes the image
less sharp. Due to the limitation of 2D NR, noise reduction may not be
effective enough.
Y LEVEL
C LEVEL
Descriptions
6.11 MOTION DET menu
Up to 4 motion detection areas are available and each area is programmable in size and location.
The motion is displayed by means of blocks when MAIN menu-2>MOTION DET and MOTION
DET>BLOCK DISP are ON.
To enter MOTION DET menu, press ● button at MAIN menu-2>MOTION DET>ON.
MOTION DET
Default
DETECT
SENSE
080
Adjusts the sensitivity for detecting motion. Higher value is more sensitive.
BLOCK DISP
ON
Enables or disables display blocks for the area where motion is detected.
MONITOR
AREA
OFF
Displays four motion windows as programmed in sizes and positions.
1/4
Selects one of AREA1~AREA4 to be adjusted.
TOP (BOTTOM) - ◀ button moves up and ▶ button moves down the top
(bottom) border of the selected window at AREA SEL.
LEFT (RIGHT) - ◀ button moves left and ▶ button moves right the left
(right) border of the selected window at AREA SEL
AREA SEL
Descriptions
16
6.12 PRIVACY menu
Up to 8 privacy areas are available and each area is programmable in size and location.
The number of privacy areas is limited to four when MOTION DET>MONITOR AREA is ON.
The privacy areas are masked with the color selected by PRIVACY>COLOR.
To enter PRIVACY menu, press ● button at MAIN menu-2>PRIVACY>ON.
PRIVACY
AREA SEL
Default
Descriptions
1/8
Selects one of AREA1~AREA8 to be adjusted.
TOP (BOTTOM) - ◀ button moves up and ▶ button moves down the top
(bottom) border of the selected window at AREA SEL.
LEFT (RIGHT) - ◀ button moves left and ▶ button moves right the left
(right) border of the selected window at AREA SEL
COLOR
1
Sets one of 8 colors for the selected mask window at AREA SEL.
TRANSP
1.00
Transparency rate for the mask can be adjusted.
0.00 - Mask is fully transparent and not visible.
0.50 - Mask is 50% transparent.
0.75 - Mask is 25% transparent.
1.00 - Mask is not transparent.
MOSAIC
OFF
Enables or disables the mosaic effect for the selected mask window at
AREA SEL
6.13 LANGUAGE menu
ENGLISH, JAPANESE, DEUTCH, FRANCAIS, RUSSIAN, PORTUGUES and ESPANOL
17
6.14 CAMERA ID menu
Up to 40 characters can be input for camera ID.
To enter CAMERA ID menu, press ● button at MAIN menu-2>CAMERA ID.
CAMERA ID input line
COMMAND LINE
Use ▲,▼,◀,▶ buttons to move a block cursor over the character table and press ● button to input the
selected character.
To move the character input position on CAMERA ID input line, move a cursor to ←→ on COMMAND
LINE and press ● button on ← or →.
To clear CAMERA ID input line, move a cursor to CLR on COMMAND LINE and press ● button.
To set the location of CAM TITLE to be displayed on the monitor, move a cursor to POS and press ●
button
and then menu disappears and CAMERA ID will be displayed on the monitor.
Move CAMERA ID by using ▲,▼,◀,▶ buttons and press ● button to fix.
Menu will appear again.
To finish CAM TITLE menu, press ● button on RET on command line.
6.15 CAMERA RESET
Camera loads Factory defaults.
To save them, go to SAVE ALL and press ● button.
6.16 EXIT
Exits SETUP MENU and returns to the normal display
18
7. Specifications
VTC-IRE30/2810
Image Device
1/3” High Density Sony EX-VIEW CCD & Effio-E DSP (960H)
Resolution
Minimum illumination
700 TV lines
0.003Lux / F1.2 (0 Lux with IR LEDs ON)
Effective Pixels
S/N Ratio
976(H) x 494(V)
More than 52dB with AGC OFF at 50IRE
Electronic Iris
1/60 to 1/100,000 sec.
Infrared LEDs
30 850nm IR LEDs
IR Distance
Over 100 Feet
Day/Night
Built-In Lens
Iris Mode
White Balance
Auto
IR Corrected 2.8-10mm DC Auto Iris Lens
DC Drive Iris Control (Internally Fixed)
1,800~10,500ºK Automatic Tracking
Gain Control
Auto
Flicker Reduction
Yes
Video Output
VBS 1 Vpp +/- 10%, 75ohm
TV System
2:1 Interlace
Scan Frequency
59.94Hz(V), 15.734Khz(V)
Synchronization
Internal/Line Lock (Default: Internal)
Light Compensation
HLC (Highlight Compensation) / BLC (Backlight Compensation)
Noise Reduction
E-WDR
2DNR
YES by ATR (Adaptive Tone Reproduction)
Motion Detection
Privacy Mask
OSD Language
YES
Up to 8 Programmable Mask Areas
English, Japanese, German, French, Russian, Portuguese, Spanish
Water Resistance
IP66
Construction
Aluminum Housing
Power Source
12VDC/24VAC (Dual Voltage)
Power Consumption (12VDC)
110mA / 455mA (IR OFF/ON)
Power Consumption (24VAC)
120mA / 400mA (IR OFF/ON)
Operating Conditions
-4ºF ~ 122ºF (-20ºC ~ 50ºC) / 85% RH Max
Length
Ceiling Mounted: 7.25" (184mm) / Wall Mounted: 8.9" (226mm)
Width
Camera: 2.5" (64mm) / Camera w/Sun Shield: 3.5" (89mm)
Height
Ceiling Mounted: 4.5” (114mm)
Weight
1.21 lbs (550g)
● Design and specifications are subject to change for product improvements without prior notice.
19
8. Dimensional Drawings
20
VT-EHL
4 & 8 Channel H.264
FEATURES:
• 4 or 8 Video Inputs with 1 Main, 1 Spot Monitor Output and 1 VGA output.
• Real Time Recording with Up to 120 IPS at HD1 Recording / Live Display (VT-EHL4)
Digital Video Recorders
Simplicity and reliability is the basis upon
which the EH L Digital Video Recorder
was conceived. With almost every
powerful feature of its predecessor the
“EH”, the EHL offers an economical
option for providing the most advanced
recording solution available. As part of
the EH family, the EHL is completely
compatible with all VITEK EH Platform
application software.
Video Input
IPS (Display / Recording)
Video Output
BNC Output
Audio In/Out
Storage
Archive
USB Port
System Control
Network
RJ-45 Ethernet Port
Playback Rate
PTZ
Point of Sale (POS)
Motion Area Setting
Recording Resolution Setting
Recording Quality Control
E-mail notification
System Configuration
Bandwidth limit
Two-Way Audio
Case Form Factor
VT-EHL4 Rear Connections
•
•
•
•
•
•
•
•
•
•
•
/ 240 IPS at CIF (VT-EHL8)
H.264 Compression
Supports Static & Dynamic IP Addresses
4 Alarm & Audio Inputs / 1 Output
500GB to 2TB Internal Storage Options
Remote Viewing over the Internet, LAN, Explorer, Safari, Firefox, Opera and Chrome
Applications for iPhone, iPad, iTouch and Droid Devices
“Quick Search” Function for automatic review
Mac OSX Client & CMS Central Management Software Included
Automatic sending of Health & Event notifications via email
Control locally via Front Panel, USB Mouse or with the Included IR Remote control
PTZ Control over RS-485
VT-EHL4VT-EHL8
4 Channels
120 / 120 (HD1)
8 Channels
240 / 240 (CIF)
VGA - 1 SXGA (1280 X1024)
Monitor: 1 Composite(BNC) / Spot: 1 Composite(BNC)
4 Line In (RCA) / 1 Line Out (RCA), CODEC : G.711 (64Kbps)
Up to 1 Internal HDD (SATA)
USB Device & Network
1 Front +1 Rear
Front Panel, USB Mouse, Included IR Remote Control
TCP/IP, HTTP, DHCP (DDNS)
10M/100M
240 fps @ 352x240
120 fps @ 704x240
60 fps @ 704x480
1 - RS-485 - Supports most of PTZ protocols with up to 255 Presets
N/A
Adjustable GRID(16X16), 10 Steps Sensitivity Level
By each camera for different resolution setting(CIF/2CIF/D1)
4 Levels (Low/Standard/High/Highest)
E-mails to specific users to notify events
Full setup configuration over network
YES: Adjustable by User
YES
1.3U
Remote Viewing Apps for iPhone, iPad
& Android
120 fps @ 704x240
60 fps @ 704x480
VT-EHL8 Rear Connections
Included VT-EH CMS Software allows
remote viewing and control of multiple
VT-EH Series DVR’s even when
located at multiple locations!
Remote Viewing from anywhere using
Internet Explorer
PROFESSIONAL LCD SERIES
Full Featured Security Monitors.
VTM-LCD
Series
15”, 17” & 19” Professional LCD Monitors
FEATURES:
Vitek Professional Grade LCD Monitors are designed for constant use
in a surveillance application. They combine sharp brilliant colors along
with easy to use OSD functions and built in speakers, 3.5mm PC Audio
and stereo RCA In/Out connections are provided for versatility and
convenience. The VTM-LCD174P and 194P also feature Dual Composite
Looping BNC Video and HDMI input along with 800:1 Contrast Ratio
delivering Industry Leading Performance and Picture Reproduction. An
Easily removable stand and VESA Mounting Capability allow for use
in Wall Mounting Applications and optional Swivel Rack Mounts are
available: Model VI-LCD174SRM/VI-LCD194SRM.
Panel Type
Display Colors
Pixel Pitch
Recommended Resolution
Contrast Ratio
Brightness
Viewing Angle
Response Time
Scanning Frequency
Video Inputs/Outputs
S-Video Input
PC Inputs
HDMI Inputs
Audio Inputs
Screen Control
LCD Lamp
VESA Mountable
Rack Mount Available
Weight
Power Supply
Dimensions (w/o Stand)
VTM-LCD154P Rear Inputs
• 15”, 17“, and 19” Professional LCD Display Panels
• Designed for continuous 24/7 operation
• VGA, Looping BNC Composite, and S-Video Video
Inputs. HDMI Inputs on 17“ & 19” Versions
• Resolution up to 1280 X 1024 (17” & 19”)
• Rated for up to a 50,000 Hour Panel Life (17” &
19”)
• Stereo Audio Input/Output
• Multi-Language OSD (On Screen Display) with
Front Panel Controls
• VESA Standard Mounting
• Optional Swivel Rack Mounts (17” & 19”)
VTM-LCD154PVTM-LCD174PVTM-LCD194P
15” TFT Color LCD
16.2 Million Colors
0.297 mm
XGA (1024x768)
700:1
260 cd/m2
H: 80 degrees V: 80 degrees
<8ms
H: 31~65kHz V: 56~75Hz
Looping BNC Composite
YES
15 pin D-Sub (Analog RGB)
N/A
Stereo RCA In / 3.5mm In/Out
OSD (On Screen Display Menu)
30,000 hours
YES
N/A
5.3lbs. (2.4kg)
AC 100~240V 50/60Hz
13.4” x 11.2” x 1.97” (340 x 284 x 50mm)
17” TFT Color LCD
16.2 Million Colors
0.264 mm
SXGA (1280 x 1024)
800:1
300 cd/m2
H: 160 degrees V: 135 degrees
<5ms
H: 31~65kHz V: 56~75Hz
Dual Looping BNC Composite
N/A
15 pin D-Sub (Analog RGB)
YES
Stereo RCA In / 3.5mm
OSD (On Screen Display Menu)
50,000 hours
YES
YES - Model VT-LCD174SRM
7.7lbs. (3.49kg)
AC 100~240V 50/60Hz
14.57” x 12.7” x 1.97” (370 x 322 x 50mm)
19” TFT Color LCD
16.2 Million Colors
0.294 mm
SXGA (1280 x 1024)
800:1
300 cd/m2
H: 160 degrees V: 135 degrees
<5ms
H: 31~65kHz V: 56~75Hz
Dual Looping BNC Composite
N/A
15 pin D-Sub (Analog RGB)
YES
Stereo RCA In / 3.5mm
OSD (On Screen Display Menu)
50,000 hours
YES
YES - Model VT-LCD194SRM
9.9lbs. (4.49kg)
AC 100~240V 50/60Hz
16.5” x 14.2” x 2.2” (419 x 360 x 56mm)
VTM-LCD174P & VTM-LCD194P Rear Inputs
VITEK LIMITED PRODUCT WARRANTY
VITEK products carry a three (3) year limited warranty. Digital recording and storage products are also warranted for 3 years except for the hard drives which carry their own independent factory warranty from the hard drive
manufacturer. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful
claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and
workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end
user. This warranty is non-transferable and extends only to the original buyer or end user customer of a Vitek
Authorized Reseller.
“Alpha Series by VITEK” products carry a three (3) year limited warranty. All other factors of the standard VITEK
warranty will apply as stated above. ** Three Year “Alpha Series by VITEK” Warranty effective September 1st
2010. “Alpha Series by VITEK” products purchased prior to September 1st 2010 carry a one (1) year warranty.
** Three Year Warranty on all products except Alpha Series became effective on April 1st 2009. Legacy Products purchased prior to April 1st 2009 carry a two (2) year warranty.
This warranty shall not apply to repairs or replacements necessitated by any cause beyond the control of
VITEK, including but not limited to, acts of nature, improper installation, excess moisture, misuse, lack of proper
maintenance, accident, voltage fluctuations, or any unauthorized tampering, repairs or modifications. This warranty becomes VOID in the event of alteration, defacement, or removal of serial numbers.
Within the first 6 months of purchase, VITEK will replace or credit any defective product at the request of the
customer (subject to availability) with a new product that equals or exceeds the performance of the original
product purchased.
Within the first 6 months of purchase, at its sole discretion, VITEK may issue an advance replacement for a
defective product; however, all related costs including, but not limited to shipping and/or delivery charges will
be the responsibility of the customer. If upon return inspection a product is determined to be in good working
order or shows evidence of misuse, the customer will be responsible for full payment of the original product
purchased as well as the replacement product.
Beyond the first 6 month period for the remainder of the warranty, VITEK’S responsibility shall be limited to
repairing the defective product, including all necessary parts and related labor costs. At its sole discretion,
VITEK may choose to either exchange a defective product or issue a merchandise credit towards future product
purchases. Any replacement parts furnished in connection with this warranty shall be warranted for a period not
to exceed the remaining balance of the original equipment warranty.
A Return Authorization number or “RA” number must be obtained prior to the return of any item for repair, replacement, or credit. VITEK requires that this “RA” number be clearly printed on the outside of the shipping carton to avoid refusal of said shipment. The Return Authorization number expires after 30 days. Products returned
after the 30 day period will be subject to refusal. Shipping charges, if any, must be prepaid. A copy of the bill of
sale (or invoice of purchase), together with a complete written explanation of the problem must accompany all
returns.
Vitek makes no warranty or guarantee whatsoever with respect to products sold or purchased through unauthorized sales channels. Warranty support is available only if product is purchased through a Vitek Authorized
Reseller.
28492 Constellation Road Valencia, ca 91355
WWW.VITEKCCTV.COM | 888-VITEK-70
Download PDF