ADTRAN | Vanta 1335 | Installation guide | ADTRAN Vanta 1335 Installation guide

NetVanta 1335 Series
Hardware Installation Guide
1700515G2#120
NetVanta 1335 with 120 VDC Power Supply
1700515G2#240
NetVanta 1335 with 240 VDC Power Supply
1700525E2
NetVanta 1335 PoE
1200861L1
NetVanta 56K/64K Network Interface Module
1202862L1
NetVanta T1/FT1 Network Interface Module
1202863L1
NetVanta T1/FT1 + DSX-1 Network Interface Module
1200872L1/1202872L1
NetVanta Dual T1 Network Interface Module
1200868E1/L1
NetVanta E1/FE1 Network Interface Module
1200878E1/L1
NetVanta E1/FE1 + G.703 Drop Network Interface Module
1200866E1
NetVanta Serial Network Interface Module
1200936E1
NetVanta SHDSL Network Interface Module, Annex A
1200937E1
NetVanta SHDSL Network Interface Module, Annex B
1202869E1
NetVanta ADSL Network Interface Module, Annex A
1202889E1
NetVanta ADSL Network Interface Module, Annex B
1200864L1
NetVanta Analog Modem Dial Backup Interface Module
1200865L1
NetVanta ISDN BRI Dial Backup Interface Module
1200875L1
NetVanta ISDN S/T Dial Backup Interface Module
1200819E1
CompactFlash®, 1 GB
61700515E2-34D
November 2012
Trademarks
NetVanta 1335 Series Hardware Installation Guide
Trademarks
Any brand names and product names included in this manual are trademarks, registered trademarks, or
trade names of their respective holders.
To the Holder of the Manual
The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change
the contents without prior notice.
In no event will ADTRAN be liable for any special, incidental, or consequential damages or for
commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication.
Software Licensing Agreement
Each ADTRAN product contains a single license for ADTRAN-supplied software. Pursuant to the
Licensing Agreement, you may: (a) use the software on the purchased ADTRAN device only and (b) keep
a copy of the software for backup purposes. This Agreement covers all software installed on the system, as
well as any software available on the ADTRAN website. In addition, certain ADTRAN systems may
contain additional conditions for obtaining software upgrades.
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
Phone: (256) 963-8000
Copyright © 2012 ADTRAN, Inc.
All Rights Reserved.
Printed in U.S.A.
2
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
Conventions
Conventions
Notes provide additional useful information.
Cautions signify information that could prevent service interruption or damage to the
equipment.
Warnings provide information that could prevent injury or endangerment to human
life.
61700515E2-34D
Copyright © 2012 ADTRAN, Inc.
3
Safety Instructions
NetVanta 1335 Series Hardware Installation Guide
Safety Instructions
When using your telephone equipment, please follow these basic safety precautions to reduce the risk of
fire, electrical shock, or personal injury:
1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in a
wet basement, or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There is a remote
risk of shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord, power supply, and batteries indicated in the manual. Do not dispose of
batteries in a fire. They may explode. Check with local codes for special disposal instructions.
5. The socket-outlet shall be installed near the equipment and shall be easily accessible.
If any of the following conditions occur, unplug the product from the electrical outlet and replace the part
or contact your qualified service personnel:
1. The power cable, extension cable, or plug is damaged.
2. An object has fallen into the product.
3. The product has been exposed to water.
4. The product has been dropped or damaged.
5. The product does not operate correctly when you follow the operating instructions.
This equipment incorporates double pole/neutral fusing. If the neutral fuse opens and the
line fuse does not open, voltage could still be present in the unit.
These units contain no user-serviceable parts. They should only be serviced by qualified
service personnel.
Additional safety guidelines, such as Waste Electrical and Electronic Equipment (WEEE),
are given in the document NetVanta Safety and Regulatory Information available at https:/
/supportforums.adtran.com.
Save These Important Safety Instructions
4
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
FCC-Required Information
FCC-Required Information
FCC regulations require that the following information be provided in this manual:
1. This equipment complies with Part 68 of Federal Communications Commission (FCC) rules and
requirements adopted by America’s Carriers Telecommunications Association (ACTA). Each
registered interface has a label that contains, among other information, a product identifier in the
format US:AAAEQ##TXXXX. If requested, provide this information to the telephone company.
2. If this equipment causes harm to the telephone network, the telephone company may temporarily
discontinue service. If possible, advance notification is given; otherwise, notification is given as
soon as possible. The telephone company will advise the customer of the right to file a complaint
with the FCC.
3. The telephone company may make changes in its facilities, equipment, operations, or procedures
that could affect the proper operation of this equipment. Advance notification and the opportunity
to maintain uninterrupted service are given.
4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty
information. The telephone company may require this equipment to be disconnected from the
network until the problem is corrected, or it is certain the equipment is not malfunctioning.
5. This unit contains no user-serviceable parts.
6. This equipment is designed to connect to the telephone network or premises wiring using an
FCC-compatible modular jack, which is compliant with Part 68 and requirements adopted by
ACTA.
7. The following information may be required when applying to the local telephone company for
leased line facilities:
Part Number
1200861L1
1202862L1
1202863L1
Registration
Number
US: HDCDENAN1200861L1
US: HDCDENAN1202863L1
1200872L1
1202872L1
US: HDCDENAN1200872L1
1200864L1
US: HDCMM04A1200864L1
Service Type
56 kbps Digital Interface
64 kbps Digital Interface
1.544 Mbps - SF
1.544 Mbps - SF and B8ZS
1.544 Mbps - ESF
1.544 Mbps - ESF and B8ZS
Analog Loop Start
REN/SOC
FIC
USOC
6.0F
04DU5-56
04DU5-64
RJ-48S
6.0N
04DU9-BN
04DU9-DN
04DU9-1KN
04DU9-1SN
RJ-48C
0.4A/9.0Y
02LS2
RJ-11C
1200865L1
US: HDCDENAN1200865L1
Basic Rate ISDN
6.0F
02LS5
RJ-49C
1202869E1
US: HDCDL01A1200869L1
ADSL Modem
0.1A
Metallic
RJ-11C
8. The ringer equivalency number (REN) is useful in determining the quantity of devices you may
connect to your telephone line and still have all of those devices ring when your number is called.
In most areas, the sum of the RENs of all devices should not exceed five. To be certain of the
number of devices you may connect to your line as determined by the REN, call your telephone
company to determine the maximum REN for your calling area.
9. This equipment may not be used on coin service provided by the telephone company. Connection
to party lines is subject to state tariffs. Contact your state public utility commission or corporation
commission for information.
61700515E2-34D
Copyright © 2012 ADTRAN, Inc.
5
FCC Radio Frequency Interference Statement
NetVanta 1335 Series Hardware Installation Guide
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Electromagnetic Compatibility (EMC) Table
NetVanta Module P/N and Name
NetVanta 1335
1200861L1
56K/64K NIM
FCC Part 15 Class A
EN 55022 Class A
1202862L1
1202863L1
1200872L1
1202872L1
T1/FT1 NIM
T1/FT1 + DSX-1 NIM
Dual T1 NIM (First Generation)
Dual T1 NIM (Second Generation)
FCC Part 15 Class A
EN 55022 Class A
1200868E1/L1
1200878E1/L1
E1/FE1 NIM
E1/FE1 + G.703 Drop NIM
FCC Part 15 Class A
EN 55022 Class A
EN 55024
1200866E1
Serial NIM
FCC Part 15 Class A
EN 55022 Class A
EN 55024
1200936E1
1200937E1
SHDSL NIM, Annex A
SHDSL NIM, Annex B
FCC Part 15 Class A
EN 55022 Class A
EN 55024
1202869E1
1202889E1
ADSL NIM, Annex A
ADSL NIM, Annex B
FCC Part 15 Class A
EN 55022 Class A
EN 55024
1200864L1
1200865L1
1200875L1
Analog Modem DIM
ISDN BRI DIM
ISDN S/T DIM
FCC Part 15 Class A
EN 55022 Class A
EN 55024
1202368L1
VPN Accelerator Card (included in P/N
4200368L1)
FCC Part 15 Class A
EN 55022 Class A
EN 55024
EN 61000-3-2
EN 61000-3-3
6
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
Industry Canada Compliance Information
Industry Canada Compliance Information
Notice: The Industry Canada label applied to the product (identified by the Industry Canada logo or the
“IC:” in front of the certification/registration number) signifies that the Industry Canada technical
specifications were met.
Notice: The REN for this terminal equipment is supplied in the documentation or on the product labeling/
markings. The REN assigned to each terminal device indicates the maximum number of terminals that can
be connected to a telephone interface. The termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the RENs of all the devices should not exceed five
(5).
Canadian Emissions Requirements
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the
Department of Communications.
Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques
de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee
par le ministre des Communications.
oll Fraud Liability
Be advised that certain security risks are inherent in the use of any telecommunications or networking
equipment, including but not limited to, toll fraud, Denial of Service (DoS) attacks, loss or theft of data, and the
unauthorized or illegal use of said equipment. ADTRAN OFFERS NO WARRANTIES, EITHER
EXPRESSED OR IMPLIED, REGARDING THE PREVENTION, DETECTION, OR DETERRENCE OF
TOLL FRAUD, NETWORKING ATTACKS, OR UNAUTHORIZED, ILLEGAL, OR IMPROPER USE OF
ADTRAN EQUIPMENT OR SOFTWARE. THEREFORE, ADTRAN IS NOT LIABLE FOR ANY LOSSES
OR DAMAGES RESULTING FROM SUCH FRAUD, ATTACK, OR IMPROPER USE, INCLUDING, BUT
NOT LIMITED TO, HUMAN AND DATA PRIVACY, INTELLECTUAL PROPERTY, MATERIAL
ASSETS, FINANCIAL RESOURCES, LABOR AND LEGAL COSTS. Ultimately, the responsibility for
securing your telecommunication and networking equipment rests with you, and you are encouraged to review
documentation regarding available security measures, their configuration and implementation, and to test such
features as is necessary for your network.
Service and Warranty
For information on the service and warranty of ADTRAN products, visit the Support section of the
ADTRAN website at http://www.adtran.com.
61700515E2-34D
Copyright © 2012 ADTRAN, Inc.
7
Service and Warranty
8
NetVanta 1335 Series Hardware Installation Guide
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SFP Module Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Option Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Power over Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
NetVanta 1335 Shipping Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
NetVanta 1335 Series Front Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
NetVanta 1335 Series Rear Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Option Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Network Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Dial Backup Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Unit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Mounting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Supplying Power to the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Installing Dial Backup and Network Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Installing a CompactFlash Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Appendix A.
61700515E2-34D
Connector Pin Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Copyright © 2012 ADTRAN, Inc.
9
Table of Contents
10
NetVanta 1335 Series Hardware Installation Guide
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
List of Figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
NetVanta 1335 Front Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta 1335 PoE Front Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta 1335 Rear Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta 56K/64K NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta T1/FT1 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta T1/FT1 + DSX-1 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta Dual T1 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta E1/FE1 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta E1/FE1 + G.703 Drop NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta Serial NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta SHDSL NIM, Annex A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta SHDSL NIM, Annex B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta ADSL NIM, Annex A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta ADSL NIM, Annex B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wallmount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing DIMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NIM and DIM Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CompactFlash Card Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61700515E2-34D
Copyright © 2012 ADTRAN, Inc.
17
17
19
22
23
24
25
26
27
28
29
30
31
32
38
39
40
41
11
List of Figures
12
NetVanta 1335 Series Hardware Installation Guide
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
List of Tables
Table 1.
Front Panel LED Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table A-1. CONSOLE Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table A-2. SFP Slot Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table A-3. 10/100Base-T Ethernet Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table A-4. 1000Base-T Gigabit Ethernet Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table A-5. WAN-T1 Connector Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table A-6. WAN-E1 Connector Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table A-7. DSX-1 Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table A-9. WAN-SHDSL Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table A-10. WAN-ADSL Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table A-8. G.703 Connector Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table A-11. Serial to Cable Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table A-12. Analog Modem and ISDN BRI DBU Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Table A-13. ISDN S/T DBU Connector Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
61700515E2-34D
Copyright © 2012 ADTRAN, Inc.
13
List of Tables
14
NetVanta 1335 Series Hardware Installation Guide
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
1.
INTRODUCTION
The NetVanta 1335 Series includes the NetVanta 1335 and NetVanta 1335 Power over Ethernet (PoE).
In this document, the term NetVanta means all NetVanta 1335 Series products. If a statement
only applies to one particular unit, the text refers to the unit individually. Additionally,
unless otherwise specified, descriptions for a NetVanta 1335 Series device also applies to
the PoE version of that device.
This hardware installation guide lists the NetVanta 1335 Series units’ physical characteristics, product
specifications, introduces basic functionality, and provides installation instructions.
•
•
•
•
Physical Description on page 16
Product Specifications on page 20
Option Modules on page 21
Unit Installation on page 36
For additional information on mounting options, powering the unit, and installing option modules, refer to the
following sections:
•
•
•
•
Mounting Options on page 37
Supplying Power to the Unit on page 38
Installing Dial Backup and Network Interface Modules on page 39
Installing a CompactFlash Card on page 41
For information on switch configuration for a specific application, refer to the configuration guides provided on
the ADTRAN Support Community. For details on the command line interface (CLI), refer to the AOS
Command Reference Guide. All other related documents are also available online at
http://supportforums.adtran.com.
61700515E2-34D
Copyright © 2012 ADTRAN, Inc.
15
Physical Description
2.
NetVanta 1335 Series Hardware Installation Guide
PHYSICAL DESCRIPTION
All NetVanta 1335 Series units are managed switches, plus multiservice routers housed in a 1U-high,
rack-mountable metal enclosure. The NetVanta 1335 Series front panels contain 24 10/100Base-T Ethernet
interfaces and two Gigabit Ethernet interfaces accessed via a fixed RJ-45 connector or small form-factor
pluggable (SFP) slots for fiber connectivity. All NetVanta 1335 Series units include IPsec virtual private network
(VPN) support (without further software upgrades) and expandable memory via CompactFlash. The NetVanta
1335 includes either a 120 VDC or 240 VDC power supply and the NetVanta 1335P includes an auto-ranging
AC power supply. All NetVanta 1335 Series units run the ADTRAN Operating System (AOS), and are
managed through an EIA-232 CONSOLE port (DB-9) located on the rear panel.
SFP Module Slots
The NetVanta 1335 Series supports two small SFP slots that accept a number of industry standard SFP modules.
The SFP modules provide Gigabit Ethernet fiber connectivity for high-speed uplinks or switch stacking. For a
list of supported SFP modules, visit the ADTRAN website at http://www.adtran.com.
Option Modules
NetVanta 1335 Series units also contain one network interface module (NIM) slot on the rear panel to support
the following modules in data applications:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1200861L1
1202862L1
1202863L1
1200872L1/1202872L1
1200868E1/L1
1200878E1/L1
1200866E1
1200936E1
1200937E1
1202869E1
1202889E1
1200864L1
1200865L1
1200875L1
56K/64K NIM
T1/FT1 NIM
T1/FT1 + DSX-1 NIM
Dual T1 NIM
E1/FE1 NIM
E1/FE1 + G.703 Drop NIM
Serial NIM
SHDSL NIM, Annex A
SHDSL NIM, Annex B
ADSL NIM, Annex A
ADSL NIM, Annex B
Analog Modem DIM
ISDN BRI DIM
ISDN S/T DIM
Power over Ethernet
The NetVanta 1335 Series PoE devices provide the same basic functionality as the other NetVanta 1335 Series
products. PoE provides the ability to detect attached powered devices (PDs), and deliver 48 VDC to the PD via
existing cabling. The PoE devices are fully compliant with the IEEE 802.3af PoE standard. By default, the PoE
switches discover and provide power to IEEE-compliant PDs.
NetVanta 1335 Shipping Contents
Each NetVanta 1335 unit is shipped in its own cardboard shipping carton. Open each carton carefully, and avoid
deep penetration into the carton with sharp objects.
16
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
Physical Description
After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in transit,
immediately file a claim with the carrier and contact ADTRAN Customer Service (refer to the Support page on
the ADTRAN website at http://www.adtran.com/support).
Domestic shipments of the NetVanta 1335 include the following items:
•
•
•
NetVanta 1335 base unit
Quick start guide
A detachable power cable with a grounded, three-prong plug
International shipments of the NetVanta 1335 include the following items:
•
•
•
NetVanta 1335 base unit
Quick start guide
All necessary power cords
NetVanta 1335 Series Front Panel Design
The NetVanta 1335 Series front panels are shown in Figure 1 below and Figure 2 on page 17. Table 1 on page
18 describes all of the LEDs, and Appendix A on page 43 shows the connector pinouts.
NetVanta 1335 Front Panel Features
10/100Base-T Ethernet Interfaces
The NetVanta 1335 Series units contain 24 10/100Base-T Ethernet interfaces (RJ-45). These interfaces
are consecutively numbered 1 through 24, from left to right, with the numbers screened directly above
each port. Status LEDs for each of these interfaces are located directly over these numbers.
Gigabit Ethernet Interfaces/SFP Slots
The NetVanta 1335 and NetVanta 1335 PoE contain two Gigabit Ethernet interfaces that provide two
fixed RJ-45 connectors and two standard SFP slots for fiber connectivity. These interfaces are labeled
G1 and G2, and the status LEDs are located above the SFP slots.
Status LEDs
The status LEDs are located to the lower left of RJ-45 port 1. The WAN LED reflects the status of an
installed NIM. The DBU LED reflects the status of an installed dial backup interface module (DIM).
The STAT LED indicates the unit’s status.
Figure 1. NetVanta 1335 Front Panel Layout
NetVanta 1335
Figure 2. NetVanta 1335 PoE Front Panel Layout
61700515E2-34D
Copyright © 2012 ADTRAN, Inc.
17
Physical Description
NetVanta 1335 Series Hardware Installation Guide
Table 1. Front Panel LED Descriptions
LED
STAT
Port LEDs
(i.e., 1 through 24, G1,
G2, etc.)
DBU
WAN
Power over Ethernet
Status LEDs
(PoE units only)
18
Color
Indication
Off
Unit is not receiving power.
Green (solid)
Power is on and self-test passed.
Green (flashing)
On power up, the STAT LED flashes rapidly for five
seconds, during which time the user may escape to boot
mode from the CONSOLE port.
Red (solid)
Power is on, but the self-test failed or the boot code could
not be booted.
Off
Port is administratively disabled or does not have a
connection.
Green (solid)
Port is enabled and has a connection.
Amber (flashing)
Port has activity (transmit or receive).
Off
No DIM is installed.
Green (solid)
DIM is ready. For the ISDN BRI DIM, green solid indicates
that the negotiation with the switch is complete.
Green (flashing)
Unit is in dial backup.
Amber (solid)
Unit is in test.
Red (solid)
Alarm condition is occurring on the DBU interface, or there
is a self-test failure.
Off
No NIM is installed, or interface is administratively down.
Green (solid)
NIM is up and everything is operational.
Green (flashing)
Port has activity (transmit or receive).
Amber (solid)
Unit is in test.
Red (solid)
Alarm condition is occurring on the WAN interface, or there
is a self-test failure.
Green (solid)
Power is being applied (48 V) to the interface.
Red (solid)
Fault is detected on the interface.
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
Physical Description
NetVanta 1335 Series Rear Panel Design
The NetVanta 1335 Series rear panels are shown below. Refer to Appendix A on page 43 for pinouts.
AC Power
WAN-T1
DSX-1
DBU
Figure 3. NetVanta 1335 Rear Panel Layout
NetVanta 1335 Rear Panel Features
NIM Option Slot
The NIM option slot accepts a variety of NIM option modules (refer to Option Modules on page 21).
CompactFlash
The CompactFlash slot supplies nonvolatile configuration and compressed code storage. The
NetVanta 1335 supports only ADTRAN-provided CompactFlash (1 GB) (refer to the part number on
the front cover of this manual).
CONSOLE Interface
The CONSOLE interface is an EIA-232 serial port (DCE) that provides for local management and
configuration (via a DB-9 female connector).
Connection directly to an external modem requires a cross-over cable.
Power Connection
The rear panel has a power input to the AC universal power supply. Please refer to Supplying Power to
the Unit on page 38 for connection details.
61700515E2-34D
Copyright © 2012 ADTRAN, Inc.
19
Product Specifications
3.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
20
NetVanta 1335 Series Hardware Installation Guide
PRODUCT SPECIFICATIONS
Multiservice access router with integrated Layer 2/3 PoE switch
Support for 24 10/100Base-T Ethernet interfaces on the front panel
Supports up to two 1000Base-T Gigabit Ethernet interfaces on the front panel (SFP slots for fiber
connectivity/RJ-45 connectors for copper connectivity)
RapidRoute technology for greater performance
Supports up to two T1s worth of bandwidth
Expandable flash memory storage via CompactFlash slot on the rear panel
Link aggregation, GARP VLAN Registration Protocol (GVRP), and Link Layer Discovery Protocol
(LLDP)
MAC-based port security
Voice quality monitoring (VQM) and mean opinion score (MOS) prediction
Network address translation (NAT) compatible Session Initiation Protocol (SIP) application layer
gateway (ALG) for Voice over IP (VoIP)
Inherent URL filtering
IPsec VPN for secure corporate connectivity across the Internet
Cable diagnostics identifies a short or open twisted pair
Recognizable CLI and intuitive Web-based graphical user interface (GUI)
Integrated DB-9, EIA-232 console port (DCE) on the rear panel
Console port, Telnet, secure shell (SSH), Simple Network Management protocol version 2 (SNMP V2),
or port mirroring management options
Modular network interface on the rear panel
Spanning tree support (802.1D and 802.1w)
Link aggregation (802.3ad)
Virtual local area network (VLAN) support (802.1Q), up to 255 active VLANs
Quality of service (QoS) with class-based weighted fair queuing (CBWFQ), low latency queuing
(LLQ), weighted fair queuing (WFQ), DiffServ marking, Frame Relay fragmentation (FRF.12), and
traffic monitoring (NetFlow 9)
Internal power supply (non-PoE versions): Either 120 or 240 VAC, 50/60 Hz, 36 watts
Internal power supply (PoE versions): 110 to 250 VAC, 50/60 Hz, 450 watts
Chassis: 1U-high, rack mountable metal enclosure
Dimensions (non-PoE versions): 1.73-inch H x 17.24-inch W x 9.49-inches D
Dimensions (PoE versions): 1.73-inch H x 17.24-inch W x 12.91-inches D
Operating temperature: 32°F (0°C) to +122°F (+50°C)
RoHS compliant, telecommunications exemption
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
4.
Option Modules
OPTION MODULES
The NetVanta 1335 Series support several option modules designed to meet a variety of networking
requirements. The option modules include plug-in NIMs and plug-on DIMs.
NIMs are cards that plug directly into the option module slot located on the rear of the base unit. These cards
provide the following types of interfaces:
•
•
•
•
•
•
•
•
•
•
•
NetVanta 56K/64K NIM (P/N 1200861L1) on page 22
NetVanta T1/FT1 NIM (P/N 1202862L1) on page 23
NetVanta T1/FT1 + DSX-1 NIM (P/N 1202863L1) on page 24
NetVanta Dual T1 NIM (P/N 1200872L1/1202872L1) on page 25
NetVanta E1/FE1 NIM (P/N 1200868E1/L1) on page 26
NetVanta E1/FE1 + G.703 Drop NIM (P/N 1200878E1/L1) on page 27
NetVanta Serial NIM (P/N 1200866E1) on page 28
NetVanta SHDSL NIM, Annex A (P/N 1200936E1) on page 29
NetVanta SHDSL NIM, Annex B (P/N 1200937E1) on page 30
NetVanta ADSL NIM, Annex A (P/N 1202869E1) on page 31
NetVanta ADSL NIM, Annex B (P/N 1202889E1) on page 32
DIMs are plug-on cards that plug directly on to the NIM prior to installation into the base unit. A DIM must be
plugged on to a NIM in order for the interfaces on the NIM to be active. The NetVanta supports the following
DIMs:
•
•
•
NetVanta Analog Modem DIM (P/N 1200864L1) on page 33
NetVanta ISDN BRI DIM (P/N 1200865L1) on page 34
NetVanta ISDN S/T DIM (P/N 1200875L1) on page 35
This section describes each module, providing individual card specifications and features. Refer to Appendix A
on page 43 for pinouts. Installing Dial Backup and Network Interface Modules on page 39 provides information
on card installation.
61700515E2-34D
Copyright © 2012 ADTRAN, Inc.
21
Option Modules
NetVanta 1335 Series Hardware Installation Guide
Network Interface Modules
NetVanta 56K/64K NIM (P/N 1200861L1)
The NetVanta 56K/64K NIM (see Figure 4) provides a digital data service (DDS) WAN interface for the
NetVanta. This module provides a single 56K or 64K DDS network interface. Refer to Appendix A on page 43
for WAN-DDS and DBU connector pinouts. An optional DIM is required for dial backup applications.
Figure 4. NetVanta 56K/64K NIM
Features and Specifications
Operating Modes
Compliance
•
•
Dedicated DDS (leased line)
DDS Interface
•
•
•
•
•
Supported Standards: AT&T TR 62310
4-wire, full-duplex
Receiver Sensitivity: -45 dB, all rates
Data Rates: 56K, 64K, and auto
Connector: RJ-48S
Clock Source
•
•
Network
Internal
Diagnostics
•
22
CSU and DSU Loopbacks
•
•
•
EMC - see Electromagnetic Compatibility
(EMC) Table on page 6.
ACTA/FCC Part 68
IC CS-03
UL/CUL 60950
Environmental
•
•
•
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent,
noncondensing
Physical
•
Dimensions: 2.75-inch W x 4.25-inch D
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
Option Modules
NetVanta T1/FT1 NIM (P/N 1202862L1)
The NetVanta T1/FT1 NIM (see Figure 5) provides a T1 WAN interface for the NetVanta. This module provides
a full T1 or fractional T1 network interface. Refer to Appendix A on page 43 for WAN-T1 and DBU connector
pinouts. An optional DIM is required for dial backup applications.
WAN-T1
DBU
Figure 5. NetVanta T1/FT1 NIM
Features and Specifications
Operating Modes
Diagnostics
•
•
•
•
Frame Relay, Multilink Frame Relay
PPP, Multilink PPP
HDLC
•
T1/FT1 Interface
•
•
•
•
•
•
•
•
•
Supported Standards: AT&T TR 62411,
AT&T TR 65016, ANSI T1.403,
Bellcore TR 194
Line Rate: 1.544 Mbps +75 bps
Line Code: AMI or B8ZS
Framing: D4 (SF) or ESF
FT1 Line Rate: DS0 channelized (multiples
of 64 kbps)
Input Signal: 0 to -36 dB (DS1)
Line Build-Out: 0, -7.5, -15, -22.5 dB
(long), 0 to 655 ft (short)
DS0 Assignment: Programmable
Connector: RJ-48C
Clock Source
•
•
Network
Internal
•
•
Compliance
•
•
•
•
EMC - see Electromagnetic Compatibility
(EMC) Table on page 6.
ACTA/FCC Part 68
IC CS-03
UL/CUL 60950
Environmental
•
•
•
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent,
noncondensing
Physical
•
61700515E2-34D
Test Pattern Generation and Detection:
511, QRSS, all ones, all zeros
Network loopbacks (local and remote);
responds to both inband and FDL loop
codes
Alarm generation and detection
Network and user sets of performance data
(15 minutes and 24 hours)
Dimensions: 2.75-inch W x 4.25-inch D
Copyright © 2012 ADTRAN, Inc.
23
Option Modules
NetVanta 1335 Series Hardware Installation Guide
NetVanta T1/FT1 + DSX-1 NIM (P/N 1202863L1)
The NetVanta T1/FT1 + DSX-1 NIM (see Figure 6) provides a T1 WAN interface for the NetVanta, a full or
fractional T1 network interface, and a DSX-1 interface. Refer to Appendix A on page 43 for WAN-T1, DSX-1,
and DBU connector pinouts. An optional DIM is required for dial backup applications.
WAN-T1
DSX-1
DBU
Figure 6. NetVanta T1/FT1 + DSX-1 NIM
Features and Specifications
Operating Modes
Clock Source
•
•
•
•
•
•
Frame Relay, Multilink Frame Relay
PPP, Multilink PPP
HDLC
T1/FT1 Interface
Diagnostics
•
•
•
•
•
•
•
•
•
•
Supported Standards: AT&T TR 62411,
AT&T TR 65016, ANSI T1.403,
Bellcore TR 194
Line Rate: 1.544 Mbps +75 bps
Line Code: AMI or B8ZS
Framing: D4 (SF) or ESF
FT1 Line Rate: DS0 channelized (multiples
of 56/64 kbps)
Input Signal: 0 to -36 dB (DS1)
Line Build-Out: 0, -7.5, -15, -22.5 dB
(long), 0 to 655 ft (short)
DS0 Assignment: Programmable
Connector: RJ-48C
DSX-1 Interface
•
•
•
•
•
•
•
•
•
24
Network
Internal
Through
Line Interface: DSX-1 per ANSI T1.102
DSX Receiver Input Range: -10 dBdsx to
+6 dBdsx
Line Rate: 1.544 Mbps
Capacity: 1 to 24 DS0s
Line Codes: AMI, B8ZS
DSX-1 Interface to PBX
Framing: D4 (SF) or ESF
Line Length: 0 to 655 feet and -7.5 dB
Connector: RJ-48C
•
•
•
Test Pattern Generation and Detection:
511, QRSS, all ones, all zeros
Network loopbacks (local and remote);
responds to inband and FDL loop codes (T1
interface only)
Alarm generation and detection
Network and user sets of performance data
(15 minutes and 24 hours)
Compliance
•
•
•
•
EMC - see Electromagnetic Compatibility
(EMC) Table on page 6.
ACTA/FCC Part 68
IC CS-03
UL/CUL 60950
Environmental
•
•
•
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent,
noncondensing
Physical
•
Dimensions: 2.75-inch W x 4.25-inch D
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
Option Modules
NetVanta Dual T1 NIM (P/N 1200872L1/1202872L1)
The NetVanta Dual T1 NIM (see Figure 7) provides two T1 WAN interfaces for the NetVanta. Refer to
Appendix A on page 43 for WAN-T1 and DBU connector pinouts. An optional DIM is required for dial backup
applications.
WAN T1/1 WAN T1/2
DBU
Figure 7. NetVanta Dual T1 NIM
Features and Specifications
Operating Modes
Diagnostics
•
•
•
•
Frame Relay, Multilink Frame Relay
PPP, Multilink PPP
HDLC
•
T1 Interface
•
•
•
•
•
•
•
•
•
Supported Standards: AT&T TR 62411,
AT&T TR 65016, ANSI T1.403,
Bellcore TR 194
Line Rate: 1.544 Mbps +75 bps
Line Code: AMI or B8ZS
Framing: D4 (SF) or ESF
FT1 Line Rate: DS0 channelized
(multiples of 64 kbps)
Input Signal: 0 to -36 dB (DS1)
Line Build-Out: 0, -7.5, -15, -22.5 dB
(long), 0 to 655 ft (short)
DS0 Assignment: Programmable
Connector: RJ-48C
Clock Source
•
•
•
Network
Internal
Through
•
•
Test Pattern Generation and Detection:
QRSS, 511, 215 - 1, 220 - 1, all ones,
all zeros
Network loopbacks (local and remote);
responds to both inband and FDL loop
codes
Alarm generation detection
Network performance data (15 minutes
and 24 hours)
Compliance
•
•
•
•
EMC - see Electromagnetic
Compatibility (EMC) Table on page 6.
ACTA/FCC Part 68
IC CS-03
UL/CUL 60950
Environmental
•
•
•
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent,
noncondensing
Physical
•
Dimensions: 2.75-inch W x 4.25-inch D
The 1200872L1 Dual T1 module supports the analog modem (1200864L1), ISDN BRI
(1200865L1), and ISDN S/T (1200875L1) DIMs for dial backup applications. The
1202872L1 Dual T1 module supports only the analog modem (1200864L1) DIM for dial
backup applications.
61700515E2-34D
Copyright © 2012 ADTRAN, Inc.
25
Option Modules
NetVanta 1335 Series Hardware Installation Guide
NetVanta E1/FE1 NIM (P/N 1200868E1/L1)
The NetVanta E1/FE1 NIM (see Figure 8) provides a WAN-E1 interface for the NetVanta meeting the
requirements of ITU-T G.703/G.704. The module provides a single 2.048 Mbps network interface. Refer to
Appendix A on page 43 for WAN-E1 and DBU connector pinouts. An optional DIM is required for dial backup
applications.
WAN-E1
DBU
Figure 8. NetVanta E1/FE1 NIM
Features and Specifications
Operating Modes
Diagnostics
•
•
•
•
Frame Relay, Multilink Frame Relay
PPP, Multilink PPP
HDLC
WAN-E1 Interface
•
•
•
•
•
•
•
Supported Standards: ITU G.703,
ITU-T G.704 (CRC-4), ITU-T G.823,
ITU-T G.797
Line Rate: 2.048 Mbps +50 PPM
Line Code: AMI or HDB3
Framing: FAS with optional CRC-4
FE1 Line Rate: Channelized timeslot (in
multiples of 64 kbps)
Receiver Sensitivity: -30 dB
Connector: RJ-48C
Clock Source
•
•
Network
Internal
•
•
•
Test Pattern Generation and Detection:
QRSS, 511, all ones, all zeros
Network loopbacks
Network performance data (15 minutes and
24 hours)
Alarm generation and detection
Compliance
•
•
•
•
•
•
•
EMC - see Electromagnetic Compatibility
(EMC) Table on page 6.
AS/ACIF S016
ETSI TBR 12/TBR 13
EN 60950
IEC 60950
AS/NZS 60950
RoHS compliant (Telecommunications
exemption)
Environmental
•
•
•
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent,
noncondensing
Physical
•
26
Dimensions: 2.75-inch W x 4.25-inch D
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
Option Modules
NetVanta E1/FE1 + G.703 Drop NIM (P/N 1200878E1/L1)
The NetVanta E1/FE1 + G.703 Drop NIM (see Figure 9) provides a single WAN-E1 interface (2.043 Mbps)
with user-selectable TS0 assignment, and a G.703 drop port that may be used to drop and insert traffic to an E1
private branch exchange (PBX). Refer to Appendix A on page 43 for WAN-E1, G.703, and DBU connector
pinouts. An optional DIM is required for dial backup applications.
WAN-E1
G.703
DBU
Figure 9. NetVanta E1/FE1 + G.703 Drop NIM
Features and Specifications
Operating Modes
Diagnostics
•
•
•
•
Frame Relay, Multilink Frame Relay
PPP, Multilink PPP
HDLC
WAN-E1 Interface
•
•
•
•
•
•
•
Supported Standards: ITU G.703,
ITU-T G.704 (CRC-4), ITU-T G.823,
ITU-T G.797
Line Rate: 2.048 Mbps +50 PPM
Line Code: AMI or HDB3
Framing: FAS with optional CRC-4
FE1 Line Rate: Channelized timeslot (in
multiples of 64 kbps)
Receiver Sensitivity: -30 dB
Connector: RJ-48C
G.703 Interface
•
•
•
•
•
•
Receiver Sensitivity: -30 dB
Line Rate: 2.048 Mbps +50 PPM
Line Code: AMI or HDB3
Framing: FAS with optional CRC-4
Capacity: 1 to 31 timeslots
Connector: RJ-48C
•
•
•
Test Pattern Generation and Detection:
QRSS, 511, all ones, all zeros
Network loopbacks
Network performance data (15 minutes
and 24 hours)
Alarm generation and detection
Compliance
•
•
•
•
•
•
•
EMC - see Electromagnetic
Compatibility (EMC) Table on page 6.
AS/ACIF S016
ETSI TBR 12/TBR 13
EN 60950
IEC 60950
AS/NZS 60950
RoHS compliant (Telecommunications
exemption)
Environmental
•
•
•
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent,
noncondensing
Clock Source
Physical
•
•
•
•
Network
Internal
Through
61700515E2-34D
Dimensions: 2.75-inch W x 4.25-inch D
Copyright © 2012 ADTRAN, Inc.
27
Option Modules
NetVanta 1335 Series Hardware Installation Guide
NetVanta Serial NIM (P/N 1200866E1)
The NetVanta Serial NIM (see Figure 10) can be configured by the user as a V.35, X.21 (V.11), or EIA 530
interface. This module supports rates up to a maximum of 10 Mbps. An additional V.35 (ADTRAN
P/N 1200873L1), X.21 (ADTRAN P/N 1200874L1), or EIA 530 (ADTRAN P/N 1200883L1) cable is required
(refer to Caution, below). Refer to Appendix A on page 43 for serial connector and DBU connector pinouts. An
optional DIM is required for dial backup applications.
Cable length for the Serial NIM should not exceed 25 feet.
SERIAL
DBU
Figure 10. NetVanta Serial NIM
Features and Specifications
Operating Mode
Environmental
•
•
•
•
DTE only
Serial Interface
•
•
•
Supported Standards: ISO 4903 (X.21),
CCITT V.35 Synchronous (V.35),
EIA 530 Synchronous
Provides V.35, X.21 (V.11), or EIA 530
electrical interface
Connector: 26-pin smart serial (DTE)
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent,
noncondensing
Physical
•
Dimensions: 2.75-inch W x 4.25-inch D
Compliance
•
•
•
•
•
•
•
•
28
EMC - see Electromagnetic
Compatibility (EMC) Table on page 6.
ETSI TBR1
ETSI TBR2
EN 60950
IEC 60950
UL/CUL 60950
AS/NZS 60950
RoHS compliant (Telecommunications
exemption)
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
Option Modules
NetVanta SHDSL NIM, Annex A (P/N 1200936E1)
The NetVanta SHDSL NIM, Annex A (see Figure 11) provides a WAN SHDSL interface for the NetVanta.
Refer to Appendix A on page 43 for WAN-SHDSL connector pinouts.
WAN-SHDSL
ANNEX A
Figure 11. NetVanta SHDSL NIM, Annex A
Features and Specifications
Operating Mode
Diagnostics
•
•
•
•
•
Line termination (CO)
Network termination (CPE)
SHDSL Interface
•
•
•
•
•
•
Supported Standards: ITU-T G.991.2
SHDSL, Annex A
M-pair bonding of 2 pairs - ITU.T
G.991.2
Line Rate (2-wire mode): 192 to
2304 kbps in 64k increments
Line Rate (4-wire mode): 384 to
4608 kbps in 128k increments
Payload: ATM (AAL5)
Line Code: TC-PAM
Connector: RJ-45
Clock Source
•
•
CPE Operating Mode: Network
CO Operating Mode: Internal
Compliance
•
•
•
•
EMC - see Electromagnetic
Compatibility (EMC) Table on page 6.
ACTA/FCC Part 68
UL/CUL 60950
RoHS compliant (Telecommunications
exemption)
Environmental
•
•
•
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent,
noncondensing
Physical
•
61700515E2-34D
Network loopbacks (local and remote)
Alarm generation and detection
Programmable alarm threshold setting for
loop attenuation and signal-to-noise ratio
Dimensions: 2.75-inch W x 4.25-inch D
Copyright © 2012 ADTRAN, Inc.
29
Option Modules
NetVanta 1335 Series Hardware Installation Guide
NetVanta SHDSL NIM, Annex B (P/N 1200937E1)
The NetVanta SHDSL NIM, Annex B (see Figure 12) provides a WAN SHDSL interface for the NetVanta.
Refer to Appendix A on page 43 for WAN-SHDSL connector pinouts.
WAN-SHDSL
ANNEX B
Figure 12. NetVanta SHDSL NIM, Annex B
Features and Specifications
Operating Mode
Diagnostics
•
•
•
•
•
Line termination (CO)
Network termination (CPE)
SHDSL Interface
•
•
•
•
•
•
Supported Standards: ITU-T G.991.2
SHDSL, Annex B
M-pair bonding of 2 pairs - ITU.T
G.991.2
Line Rate (2-wire mode): 192 to
2304 kbps in 64k increments
Line Rate (4-wire mode): 384 to
4608 kbps in 128k increments
Payload: ATM (AAL5)
Line Code: TC-PAM
Connector: RJ-45
Clock Source
•
•
CPE Operating Mode: Network
CO Operating Mode: Internal
Network loopbacks (local and remote)
Alarm generation and detection
Programmable alarm threshold setting for
loop attenuation and signal-to-noise ratio
Compliance
•
•
•
•
•
EMC - see Electromagnetic
Compatibility (EMC) Table on page 6.
AS/ACIF S043
EN 60950
AS/NZS 60950
RoHS compliant (Telecommunications
exemption)
Environmental
•
•
•
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent,
noncondensing
Physical
•
30
Dimensions: 2.75-inch W x 4.25-inch D
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
Option Modules
NetVanta ADSL NIM, Annex A (P/N 1202869E1)
The NetVanta ADSL NIM, Annex A (see Figure 13) adds ADSL capability to the NetVanta. The module
provides a single ADSL, ADSL2, or ADSL2+ network interface to support rates up to 25 Mbps. Refer to
Appendix A on page 43 for WAN-ADSL and DBU connector pinouts. An optional DIM is required for dial
backup applications.
WAN-ADSL
DBU
Figure 13. NetVanta ADSL NIM, Annex A
Features and Specifications
ADSL Interface
Compliance
•
•
•
•
ADSL over POTS, Annex A
Supported Standards:
– ITU G.992.1 (G.dmt)
– ITU G.992.2 (G.lite)
– ITU G.992.3 ADSL2 (G.dmt.bis)
– ITU G.992.5 ADSL2+
– ANSI T1.413 Issue 2
– Reach Extended ADSL (READSL2)
Connector: RJ-11C (6-pin jack, inner
pair)
•
•
•
•
•
•
•
•
•
ATM
•
•
•
•
•
•
•
Multiple Protocol over AAL5
(RFC 2684)
PPP over ATM (RFC 2364)
PPP over Ethernet (RFC 2516)
ATM Forum UNI 3.1/4.0 PVC
ATM Class of Service (UBR)
ATM F5 OAM
Up to 16 Virtual Circuits
61700515E2-34D
EMC - see Electromagnetic
Compatibility (EMC) Table on page 6.
ACTA/FCC Part 68
AS/ACIF S043
AS/ACIF S002
IC CS-03
EN 60950
IEC 60950
UL/CUL 60950
AS/NZS 60950
RoHS compliant (Telecommunications
exemption)
Environmental
•
•
•
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent,
noncondensing
Physical
•
Dimensions: 2.75-inch W x 4.25-inch D
Copyright © 2012 ADTRAN, Inc.
31
Option Modules
NetVanta 1335 Series Hardware Installation Guide
NetVanta ADSL NIM, Annex B (P/N 1202889E1)
The NetVanta ADSL NIM, Annex B (see Figure 14) adds ADSL capability to the NetVanta. Refer to
Appendix A on page 43 for WAN-ADSL and DBU connector pinouts. An optional DIM is required for dial
backup applications.
WAN-ADSL
DBU
Figure 14. NetVanta ADSL NIM, Annex B
Features and Specifications
ADSL Interface
Compliance
•
•
•
•
ADSL over ISDN, Annex B
Supported Standards: ITU G.992.1
(G.dmt)
Connector: RJ-11C (6-pin jack,
inner pair)
ATM
•
•
•
•
•
•
•
Multiple Protocol over AAL5
(RFC 2684)
PPP over ATM (RFC 2364)
PPP over Ethernet (RFC 2516)
ATM Forum UNI 3.1/4.0 PVC
ATM Class of Service (UBR)
ATM F5 OAM
Up to 16 Virtual Circuits
•
•
•
•
•
Environmental
•
•
•
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent,
noncondensing
Physical
•
32
EMC - see Electromagnetic
Compatibility (EMC) Table on page 6.
AS/ACIF S043
EN 60950
IEC 60950
AS/NZS 60950
RoHS compliant (Telecommunications
exemption)
Dimensions: 2.75-inch W x 4.25-inch D
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
Option Modules
Dial Backup Interface Modules
NetVanta Analog Modem DIM (P/N 1200864L1)
The Analog Modem DIM provides a modem with data rates up to 33.6 kbps for the NetVanta. This DIM is a
plug-on card that connects to the NIM. For installation instructions, refer to Installing Dial Backup and Network
Interface Modules on page 39.
Features and Specifications
Features
•
•
Supported Standards: ITU V.90
Async
Compliance
•
•
•
•
EMC - see Electromagnetic Compatibility (EMC) Table on page 6.
ACTA/FCC Part 68
IC CS-03
UL/CUL 60950
Environmental
•
•
•
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent, noncondensing
Physical
•
Dimensions: 2.5-inch W x 3.75-inch D
The Analog Modem DIM can be used in two different modes:
1. Backup interface for a primary connection.
2. CONSOLE port for remote dial-in access.
61700515E2-34D
Copyright © 2012 ADTRAN, Inc.
33
Option Modules
NetVanta 1335 Series Hardware Installation Guide
NetVanta ISDN BRI DIM (P/N 1200865L1)
The NetVanta ISDN BRI DIM provides dial backup access to the public switched telephone network (PSTN)
via Basic Rate ISDN for the NetVanta. This DIM is a plug-on module that connects to the NIM. For installation
instructions, refer to Installing Dial Backup and Network Interface Modules on page 39.
Features and Specifications
Features
•
•
•
•
Clear channel and bonding mode 1 call protocols
Network support for 64 kbps (1 B-channel) or 128 kbps (2 B-channels)
D-channel switch compatibility with AT&T 5ESS, Northern Telecom DMS-100, and National
ISDN-1
V.54 network loopback support
Compliance
•
•
•
•
EMC - see Electromagnetic Compatibility (EMC) Table on page 6.
ACTA/FCC Part 68
IC CS-03
UL/CUL 60950
Environmental
•
•
•
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent, noncondensing
Physical
•
34
Dimensions: 2.5-inch W x 3.75-inch D
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
Option Modules
NetVanta ISDN S/T DIM (P/N 1200875L1)
The NetVanta ISDN S/T DIM provides dial backup access to the PSTN via Basic Rate ISDN for the NetVanta.
This DIM is a plug-on module that connects to the NIM. For installation instructions, refer to Installing Dial
Backup and Network Interface Modules on page 39.
Features and Specifications
Features
•
•
•
•
Clear channel and bonding mode 1 call protocols
Network support for 64 kbps (1 B-channel) or 128 kbps (2 B-channels)
D-channel switch compatibility with AT&T 5ESS, Northern Telecom DMS-100, National ISDN-1,
and Euro-ISDN
V.54 network loopback support
Compliance
•
•
•
•
•
•
EMC - see Electromagnetic Compatibility (EMC) Table on page 6.
AS/ACIF S031
ETSI TBR 3
EN 60950
IEC 60950
AS/NZS 60950
Environmental
•
•
•
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent, noncondensing
Physical
•
Dimensions: 2.5-inch W x 3.75-inch D
61700515E2-34D
Copyright © 2012 ADTRAN, Inc.
35
Unit Installation
5.
NetVanta 1335 Series Hardware Installation Guide
UNIT INSTALLATION
The instructions and guidelines provided in this section cover hardware installation topics, such as mounting
options, supplying power to the unit, and installing option cards. These instructions are presented as follows:
•
•
•
•
•
Tools Required on page 36
Mounting Options on page 37
Supplying Power to the Unit on page 38
Installing Dial Backup and Network Interface Modules on page 39
Installing a CompactFlash Card on page 41
For information on switch configuration for a specific application, refer to the configuration guides provided on
the ADTRAN Support Community. For details on the command line interface (CLI), refer to the AOS
Command Reference Guide. All other related documents are also available online at
http://supportforums.adtran.com.
To prevent electrical shock, do not install equipment in a wet location or during a
lightning storm.
The NetVanta 1335 Series is intended to be installed, maintained, and serviced by qualified
service personnel only and should be installed in a restricted access location as described
in UL/IEC 60950-1.
• PoE cables are intended for intrabuilding use only. Connecting an ADTRAN PoE unit
directly to PoE cables that run outside the building in which the unit is housed will void
the user's warranty and could create a fire or shock hazard.
• Ethernet cables are intended for intrabuilding use only. Connecting an ADTRAN unit
directly to Ethernet cables that run outside the building in which the unit is housed will
void the user's warranty and could create a fire or shock hazard. To connect an
ADTRAN unit to Ethernet cables that run outside the building, ADTRAN's Ethernet
Port Protection Device (EPPD) (P/N 1700502G1) must be connected between the unit
and the outside plant cable. Use of any Ethernet protector other than ADTRAN's for this
purpose will void the user's warranty.
Tools Required
The customer-provided tools required for the hardware installation of the NetVanta are:
•
•
•
•
•
Ethernet cables
Network cables (module dependent)
DSX-1 cable (T1/FT1 + DSX-1 module only)
DBU cable (dial backup functions require an optional DIM)
Phillips-head screwdriver
To access the CLI of the NetVanta, you will also need a PC with VT100 terminal emulation
software and a console port cable. Instructions on how to access the CLI are available in
the quick start guide shipped with your unit or online on the ADTRAN Support Community.
36
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
Unit Installation
Mounting Options
The unit may be installed in rackmount, wallmount, or tabletop configurations. The following sections provide
step-by-step instructions for rack mounting and wall mounting.
Rack Mounting the NetVanta
The NetVanta is a 1U-high, rack-mountable unit that can be installed into a 19-inch equipment rack. The
following steps guide you in mounting the NetVanta into a rack.
•
•
•
•
•
If installed in a closed or multi-unit rack assembly, the operating ambient temperature
of the rack environment may be greater than room ambient temperature. Therefore,
consideration should be given to installing the equipment in an environment compatible
with the maximum ambient temperature specified by the manufacturer.
Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised.
Be careful not to compromise the stability of the equipment mounting rack when
installing this product.
Consideration should be given to the connection of the equipment to the supply circuit
and the effect that overloading the circuit might have on overcurrent protection and
supply wiring. Appropriate consideration of equipment nameplate ratings should be
used when addressing this concern.
Reliable grounding of rack-mounted equipment should be maintained. Particular
attention should be given to supply connections other than direct connections to the
branch circuit (e.g., use of power strips).
Instructions for Rack Mounting the NetVanta
Step
Action
1
To allow proper grounding, scrape the paint from the rack around the mounting holes where the
NetVanta will be positioned.
2
Position the NetVanta in a stationary equipment rack. This unit occupies 1U of space.
3
Have an assistant hold the unit in position as you install two mounting bolts through the unit’s
brackets and into the equipment rack using a #2 Phillips-head screwdriver.
4
Apply power to the unit (refer to Supplying Power to the Unit on page 38).
Wall Mounting the NetVanta
By following these instructions exactly, the NetVanta can be safely mounted on the wall.
•
•
•
61700515E2-34D
To avoid damaging the unit, use only the screws included in the shipment when
attaching mounting ears to the chassis.
When wall mounting the NetVanta, care must be taken not to damage the power cord.
Do not attach the power cord to the building surface or run it through walls, ceilings,
floors, or openings in the building structure.
The socket-outlet must be installed near the equipment and must be easily accessible.
Copyright © 2012 ADTRAN, Inc.
37
Unit Installation
NetVanta 1335 Series Hardware Installation Guide
Instructions for Wall Mounting the NetVanta
Step
Action
1
Remove the mounting ears. Rotate them 90 degrees so that the portion of the bracket with the
mounting holes is flush with the bottom of the chassis. Reattach the mounting ears to the
chassis (see Figure 15).
2
Decide on a location for the NetVanta. All NetVanta 1335 Series units are mounted with the
front panel facing down (see Figure 15). Keep in mind that the unit needs to be mounted at or
below eye level so that the LEDs are viewable.
3
Prepare the mounting surface by attaching a board (typically plywood, 3/4-inch to 1-inch thick)
to a wall stud using #6 to #10 (2.5-inch or greater in length) wood screws.
Important! Mounting to a stud ensures stability. Using sheetrock anchors may not provide
sufficient long-term stability.
4
Have an assistant hold the unit in position as you install two #6 to #10 (1-inch or greater in
length) wood screws through the unit’s brackets and into the mounted board (see Figure 15).
5
Proceed to the steps given in Supplying Power to the Unit below.
SLOT 1 NIM/VIM
CONSOLE
100-250 VAC
50-60Hz
Figure 15. Wallmount Installation
Supplying Power to the Unit
The NetVanta 1335 Series units come equipped with an either a 120 VDC 50/60 Hz or 240 VDC 50/60 Hz
power supply for connecting to a properly grounded power receptacle. (All appropriate power cords are
included in the shipment of the unit.) To power these units, connect the power cable to an appropriately
grounded power source.
38
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
Unit Installation
Installing Dial Backup and Network Interface Modules
The DIM plugs on to the NIM. The NIM is then installed into the rear panel option module slot. The following
tables list the installation steps. Also, see Figure 16 below and Figure 17 on page 40.
For NetVanta modules with outside plant connections, ensure that all cables are
removed from the module before installing or removing it from the NetVanta chassis.
Electronic modules can be damaged by static electrical discharge. Before handling
modules, put on an antistatic discharge wrist strap to prevent damage to electrical
components. Place modules in antistatic packing material when transporting or storing.
When working on modules, always place them on an approved antistatic mat that is
electrically grounded.
Instructions for Installing the DIMs
Step
Action
1
Remove power from the unit.
2
If the NIM is already in the NetVanta chassis, remove all cables, release the pins at both edges
of the NIM front panel, and slide the module out of the chassis.
3
Carefully align the P1 connector on the NIM with the J1 connector on the DIM. Using only fingertip
pressure so that neither circuit board bends or flexes, ensure that the connectors are firmly seated.
Secure the DIM to the NIM using the screws and standoff posts supplied. See Figure 16.
4
Slide the NIM with the DIM attached into the NetVanta chassis, continuing with the normal NIM
installation (refer to Instructions for Installing the NIMs on page 40).
Figure 16. Installing DIMs
61700515E2-34D
Copyright © 2012 ADTRAN, Inc.
39
Unit Installation
NetVanta 1335 Series Hardware Installation Guide
Instructions for Installing the NIMs
Step
Action
1
Remove power from the unit.
2
Use a screwdriver to remove the cover plate from the appropriate option slot in the NetVanta
base unit.
3
Slide the option module into the option slot until the module is firmly seated against the chassis.
4
Secure the pins at both edges of the module.
5
Connect the cables to the associated device(s).
6
Restore power to the unit.
AC Power
WAN-T1
DSX-1
DBU
Figure 17. NIM and DIM Installation
40
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
Unit Installation
Installing a CompactFlash Card
The CompactFlash slot supports only ADTRAN-provided 1 GB CompactFlash cards. Follow these
instructions when installing a card
The CompactFlash card is hot-swappable and can be inserted or removed while power is
applied to the unit.
Instructions for Installing a CompactFlash Card
Step
Action
Slide the module into the CompactFlash slot until the card is firmly seated against the chassis.
2
The CompactFlash options will now be available in the GUI and the AOS CLI.
Com
pac
tFla
sh
1
Figure 18. CompactFlash Card Installation
Your NetVanta unit is now ready to be configured and connected to the network. For information on
configuration for a specific application, refer to the configuration guides provided on the ADTRAN Support
Community. For details on the command line interface (CLI), refer to the AOS Command Reference Guide. All
other related documents are also available online at http://supportforums.adtran.com.
61700515E2-34D
Copyright © 2012 ADTRAN, Inc.
41
Unit Installation
42
NetVanta 1335 Series Hardware Installation Guide
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
APPENDIX A.
CONNECTOR PIN DEFINITIONS
The following tables provide the pin assignments for the base unit, NIMs, and DIMs.
Base Unit Pinouts
Table A-1. CONSOLE Port Pinouts
Pin
Name
Description
1
DCD
2
RD
Receive Data (output)
3
TD
Transmit Data (input)
4
DTR
5
SG
6
DSR
7
—
8
CTS
9
—
Data Carrier Detect (output)
Data Terminal Ready (input)
Signal Ground
Data Set Ready Tied to pin 1 (output)
Unused
Clear to Send Tied to pin 1 (output)
Unused
Table A-2. SFP Slot Pinouts
Pin
Name
Pin
Name
1
TGND
11
RGND
2
TX FAULT
12
RX-
3
TX DISABLE
13
RX+
4
MOD DEF(2)
14
RGND
5
MOD DEF(1)
15
VccR
6
MOD DEF(0)
16
VccT
7
RATE SELECT
17
TGND
8
LOS
18
TX+
9
RGND
19
TX-
10
RGND
20
TGND
61700515E2-34D
Copyright © 2012 ADTRAN, Inc.
43
Appendix A. Connector Pin Definitions
NetVanta 1335 Series Hardware Installation Guide
Table A-3. 10/100Base-T Ethernet Port Pinouts
Pin
Name
Description
1
TX1
Transmit Positive
2
TX2
Transmit Negative
3
RX1
Receive Positive
4, 5
—
6
RX2
7, 8
—
Unused
Receive Negative
Unused
Table A-4. 1000Base-T Gigabit Ethernet Port Pinouts
44
Pin
Name
Description
1
TRD0+
Transmit/Receive Positive
2
TRD0-
Transmit/Receive Negative
3
TRD1+
Transmit/Receive Positive
4
TRD2+
Transmit/Receive Positive
5
TRD2-
Transmit/Receive Negative
6
TRD1-
Transmit/Receive Negative
7
TRD3+
Transmit/Receive Positive
8
TRD3-
Transmit/Receive Negative
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
Appendix A. Connector Pin Definitions
Network Interface Module Pinouts
Table A-5. WAN-T1 Connector Pinouts
Pin
Name
Description
1
R1
Receive data from the network–Ring 1
2
T1
Receive data from the network–Tip 1
3
—
Unused
4
R
Transmit data toward the network–Ring
5
T
Transmit data toward the network–Tip
6-8
—
Unused
Table A-6. WAN-E1 Connector Pinouts
Pin
Name
Description
1
R1
Receive data from the network–Ring 1
2
T1
Receive data from the network–Tip 1
3
—
Unused
4
R
Transmit data toward the network–Ring
5
T
Transmit data toward the network–Tip
6-8
—
Unused
Table A-7. DSX-1 Connector Pinouts
Pin
Name
1
R
Transmit data toward the DTE–Ring
2
T
Transmit data toward the DTE–Tip
3
—
Unused
4
R1
Receive data from the DTE–Ring 1
5
T1
Receive data from the DTE–Tip 1
6-8
—
Unused
61700515E2-34D
Description
Copyright © 2012 ADTRAN, Inc.
45
Appendix A. Connector Pin Definitions
NetVanta 1335 Series Hardware Installation Guide
Table A-8. G.703 Connector Pinouts
Pin
Name
Description
1
R
Transmit data toward the DTE–Ring
2
T
Transmit data toward the DTE–Tip
3
—
Unused
4
R1
Receive data from the DTE–Ring 1
5
T1
Receive data from the DTE–Tip 1
6-8
—
Unused
Table A-9. WAN-SHDSL Connector Pinouts
Pin
Name
Description
1
T2
Loop 2–Tip
2
R2
Loop 2–Ring
3
—
Unused
4
T1
Loop 1–Tip
5
R1
Loop 1–Ring
6-8
—
Unused
Table A-10. WAN-ADSL Connector Pinouts
46
Pin
Name
Description
1, 2
—
Unused
3
R
ADSL Ring
4
T
ADSL Tip
5, 6
—
Unused
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
NetVanta 1335 Series Hardware Installation Guide
Appendix A. Connector Pin Definitions
Table A-11. Serial to Cable Connector Pinouts
Serial
Pin
V.35
Pin
X.21
Pin
EIA 530
Pin
Name
1
P
2
2
TD_A
2
U
N/A
24
ETC_A
3
Y
N/A
15
TCLK_A
4
V
6
17
RCLK_A
5
R
4
3
RD_A
6
F
N/A
8
DCD_A
7
H
N/A
20
DTR_A
8
C
3
4
RTS_A
9
N/A
10
19
RTS_B (V.11 only)
10
N/A
12
13
CTS_B (V.11 only)
11
D
5
5
CTS_A
12
E
N/A
6
DSR_A
13
K
N/A
25
TM_A
14
S
9
14
TD_B
15
W
N/A
11
ETC_B
16
AA
N/A
12
TCLK_B
17
X
13
9
RCLK_B
18
T
11
16
RD_B
19-25
N/A
N/A
N/A
Unused
26
B
8
7
Ground
61700515E2-34D
Copyright © 2012 ADTRAN, Inc.
47
Appendix A. Connector Pin Definitions
NetVanta 1335 Series Hardware Installation Guide
Dial Backup Interface Module Pinouts (DBU Connector)
An optional DIM is required for dial backup applications.
Table A-12. Analog Modem and ISDN BRI DBU Connector Pinouts
Pin
Name
Description
1-3
—
Unused
4
R
Network–Ring
5
T
Network–Tip
6-8
—
Unused
Table A-13. ISDN S/T DBU Connector Pinouts
48
Pin
Name
Description
1, 2
—
Unused
3
R1
Network Receive–Ring 1
4
R
Network Transmit–Ring
5
T
Network Transmit–Tip
6
T1
Network Transmit–Tip 1
7, 8
—
Unused
Copyright © 2012 ADTRAN, Inc.
61700515E2-34D
Download PDF