Professional Power Amplifiers
more than 60 years of amplifiers experience
Mobile Audio | Concert Sound | Fixed Installation | Pro Entertainment
English
Contents
Contents
Introduction
Products
technical specifications
Contents
02
PowerH Series
12-17
Application
54
One Brand Fits All
03
Remote Control & IRIS-Net
18
PowerH Series
55
History
04-05
RCM-26 Controller Modul
19-21
Xa 4000
56
Milestones
06-07
LX Series
22-27
LX Series
57
Manufacturing
08-09
CL Series
28-33
CL Series
58-59
Bosch Production System
10-11
SL Series
34-37
SL Series
60-61
DSA Series - Multi-Channel
38-41
DSA Series
62-65
RCM-810 Controller Modul
42-43
PCL Series
66-67
DSA Serie - Dual-Channel
44-45
DPA Series
68-71
PCL Series
46-49
DPA Series
50-53
2
One Brand Fits All
One Brand Fits All
In our multimedia world, professional audio systems are
playing an ever more important role. For this, power amplifiers
are needed the characteristics and properties of which are
tailored precisely to the application in question.
The spectrum of these requirements—from live music to fixed
installation—has an extremely wide bandwidth and extends from
very high power output combined with minimum weight to remote
supervision and network capability. DYNACORD’s extensive power
amplifier portfolio offers an ideal and cost-effective solution for
every field of application.
3
History
German Engineering Excellence
For more than 60 years, DYNACORD has been one of the most innovative and successful manufacturers of professional audio equipment.
4
History
In 1945 Werner Pinternagel,
who was an engineer, founded a
workshop for the repair of radio
devices in the Lower Bavarian
town of Pilsting. The development
and manufacture of audio amplifiers,
which he began at the same time,
became a particular passion.
These pioneering experiences
formed the foundation for over 60
years of expertise in professional
power amplifier technology—
expertise upon which the brand
DYNACORD is able to draw today.
Early results included the KI cinema
amplifier with its output of 25 watts.
The devices of the company, which
in the meantime had moved to
Landau and by then boasted a
staff of four employees, still bore
the brand name ‘Dynaphon’.
From 1948 onwards, mixing and
portable amplifiers bearing the
name DYNACORD were being
sold to an ever expanding circle
of customers. Within a few years,
the rapidly growing company had
become one of the leading enterprises in the still young audio
technology industry. Already in
1954, the manual workshop have
given way to industrial production
as the product portfolio continued to
expand. The high-caliber, pioneering
and often visionary products have
been presented ever since at all
important international trade fairs
and marketed successfully throughout
the world. To make it possible to
satisfy the enormous demand,
DYNACORD moved to Straubing in
1958. The workforce, which at that
time numbered 80 employees, continued to expand rapidly. Several
times, the production facility was
renovated or expanded.
Finally, in 1986 a new plant was
opened in which more than 500
employees now develop, produce
and dispatch the company’s products to all corners of the globe.
5
Milestones
Milestones
The constantly expanding product
range yielded many pro audio milestones.
6
Milestones
A high degree of innovation, uncompromising
quality, exceptional user-friendliness and truely
legendary reliability and value retention have for
over 60 years defined the brand DYNACORD.
• the first generations of professional mixing amplifiers [Eminent, Gigant]
• the first tape-echo/reverb devices [Echochord]
• the first ‘affordable’ digital reverb device [DRS 78]
Echocord
• the most advanced digital drums
[ADDone, ADDtwo]
• the first professional digital reverb device based
on 32-bit floating-point processing [DRP-20]
• the first processor power amplifiers
with LPN filters [PCA series]
DRS-78
• one of the most successful power amplifiers
in concert sound [L2400 / EV P3000]
• the first processor-controlled complete audio system [P3, P5]
• the first digital loudspeaker controller with graphic display of the acoustic system frequency
response in the editing software [DSP 224/244
with CrossMax and EV Dx34/38 with RACE]
PowerMate
• the Planar Waveguide bass horns [F 18, Alpha B3 and many others]
• the world’s most powerful disco system [Alpha]
• the world’s most successful powered mixer [PowerMate]
• the first stackable compact line array system [Cobra]
• the first Class H grounded bridge high-performance power amplifiers [PowerH]
Cobra
• the unique IRIS-Net network software [incl. remote supervision, remote control of
power amplifiers and digital audio matrices]
• the first digital power amplifiers with VLD-variable load drive [DSA Multi-Channel]
PowerH
7
Bosch Production System
8
Bosch Production System
Bosch Production
System
Quality with system
With the introduction of the Bosch Production System
(BPS) at the Straubing works, the brand DYNACORD is
further enhancing its already legendary reputation for
the highest production quality and reliability.
Quality with system is assured by the BPS worldwide in
all Bosch production centres, since absolutely identical
indicators, equipment and processes are applied
systematically throughout the enterprise. Decisions
about which products to produce in which plant are
primarily based on core areas of competence.
The same goes for the development. The first measures to
guarantee quality are applied as early as the development phase of a product, where the ‘thermal and
mechanical stability’, the ‘secure functioning of the
circuitry’ and the demands of quality such as the
acoustic performance and the product functions
themselves are all ascertained in advance and rigorous
tests conducted before any final decisions are taken
about the design.
Decades of experience and the most modern quality
management systems guarantee the extraordinary quality
and legendary reliability of DYNACORD products.
9
Manufacturing
Measurement Hall
Part of the new investment involved the construction and
commissioning of what at 600 square metres is one of the
world’s largest audio measurement halls.
Manufacturing
Since September 2006, DYNACORD has belonged
to the BOSCH concern’s Security Technology
department.
The production facility in Straubing has been considerably
expanded and the work reorganized along the lines of
the Bosch Production System (BPS). Part of the new
investment involved the construction and commissioning
of what at 600 square metres is one of the world’s
10
Manufacturing in Straubing, Germany
Manufacturing
largest audio measurement halls. One of the particular
strengths of the brand DYNACORD is the fact that
over the many years of its history profound know-how,
covering the entire signal chain from the mixer to the
loudspeakers has been acquired.
This advantage, coupled with its traditionally close
relationship with users, has yielded many unique solutions to once-vexing problems and helped DYNACORD to
develop a reputation the world over as a manufacturer
of top-flight audio equipment on the absolute cutting
edge of development.
Additional capacity is available at the Bosch
plant in Zhuhai, China, where the production also
conforms to the BPS and quality controls are
conducted using identical procedures and equipment.
Manufacturing in Zhuhai, China
11
recommended applications
ConcertSound, Touring, Club/Disco, ProSound, Network
“All the measured data and the stability
under continuous output are—as expected—
of the highest order”
PowerH 5000 test in `Production Partner` 10/2007
12
PowerH Series
The PowerH power amp series represents a further milestone in the 60-year
pro audio tradition of DYNACORD.
·· H 2500
·· H 5000
DYNACORD has long been established worldwide as a manufacturer of
professional high-performance amplifiers and by virtue of numerous
innovations and the downright legendary reliability of its products has
secured for itself a firm place in the elite segment. No small contribution
to this success has been made by the firm’s largest OEM customer: its
sister company, Electro-Voice.
For years now, countless large and very large sound reinforcement
systems installed or on tour throughout the world have been relying on
DYNACORD/Electro-Voice power amps. Thousands of amplifiers made
by DYNACORD have been deployed on every continent and performed
with distinction at many of the truly major productions of recent years.
13
PowerH Series
PowerH Series
HI-end remote controllable power amplifiers
The demands placed on modern
power amplifiers are enormous:
maximum output, minimum
weight, the highest possible
degree of efficiency, outstanding
audio characteristics, absolute
reliability, remote supervision
and remote control as well as
network capability.
To realize stable outputs of 2500 W /
4 Ω and 3500 W / 2 Ω per channel,
power amplifiers must be capable
of making available peak output
voltages of 180 V to 200 V. This
requirement limits the number of
14
topologies meriting consideration
to two concepts only: Class D and
DYNACORD’s Linear Grounded
Bridge Class H. Linear Push-Pull
concepts with Class H topology
are proven solutions for power
levels up to 1500 W / 4 Ω.
This is the approach adopted by
many DYNACORD power amplifiers.
The limitation of the Class H push-pull
approach is the 250 V specification
of typical audio power transistors
and their second breakdown
restrictions. Even exceeding the
specified peak voltage or the
second breakdown limit for short
periods leads directly to a failure
of the power transistors and the
power amplifier. The use of exotic
350V-specified transistors affords
no reliable solution in view of their
second breakdown behaviour,
their performance and also their
availability.
Higher power classes require
different solutions! DYNACORD‘s
linear Grounded Bridge designs
(e.g. L2400 / P3000) have proved
extremely reliable over many years
as well as outstanding in terms
PowerH Series
of audio performance. One of
the key advantages of Grounded
Bridge solutions is the considerable
reduction in ‚voltage stress‘ for the
power transistors. This permits
the design of high-powered power
amplifiers with peak output voltages
in excess even of 200 V.
A logical step in the direction of
lowering power dissipation whilst
at the same time increasing the
output power was the development
of a linear Grounded Bridge topology using Class H technology with
a multi-stage switching ‚floating‘ po-
wer supply. The use of an extremely
stable switching power supply
makes a decisive contribution to
the very low weight of these power
amplifiers: 7 kW packed into a device
a mere 2 rack units in height and
weighing less than 15 kg!
PowerH power amplifiers are ready
for integration into IRIS-Net-based
audio systems and networks.
Remote control modules (e.g. the
RCM-26) that can be retrofitted
offer complete system supervision
and remote control combined with
digital controller functions.
Features
• stable, very high power output
• very high efficiency
• very lightweight
• multi-stage Grounded Bridge
Class H topology
• ‚floating‘ switching power supply
• large liquid crystal display
• integrated micro-controller
for internal control
• remote control module can be retrofitted for integration into the
IRIS-Net bringing supervision, remote control, digital controller
functions and digital audio inputs
15
PowerH Series
“All in all, a perfect combination, in which it is evident from
every detail that the developers knew exactly what a high-end
power amplifier for the professional touring and installation
market needs.”
PowerH 5000 test in `Production Partner` 10/2007
The power amplifiers of the
PowerH series represent a
milestone in the design and
production of high-performance
power amplifiers.
Their innovative multi-stage Grounded
Bridge Class H topology with its
floating switching power supply
offers very high and stable output
power, very high efficiency, an extremely high level of audio
performance and extremely low
weight.
They are therefore the ideal drivers
for professional touring and highend concert sound, as well as pro
sound, applications. Through the
use of IRIS-Net-compatible remote
control modules, they also offer
extensive remote supervision and
control functions as well as a universal two-channel digital controller
including ultra-precise FIR filtering
and digital algorithms to protect
16
the loudspeakers. DYNACORD power
amplifiers are known for their
absolute reliability under the most
arduous of conditions on the road.
Naturally this is also true of the
PowerH models.
In addition to the legendary manufacturing quality that comes with
the ‚Made in Germany‘ label, the
comprehensive set of protective
circuits plays an important role
here: an integrated micro-controller
coordinates tried-and-tested
protections against short-circuit,
HF or DC at the output, back EMF,
overheating and open-circuit operation, the power-up current limitation
and dynamic audio limiters as well
as making additional new and highly intelligent protective functions
possible: for example, the temperature in the power amplifiers is
monitored at no fewer than six different points and the front-to-rear
ventilator governed accordingly.
Under abnormal thermal ‚worst
case‘ conditions, the CPU activates
a voltage limiter or gain reduction
depending upon the requirements of
the situation, so as to obviate the
need for a thermal shutdown of
the power amplifiers. All corrective
measures are indicated by LEDs on
the front panel and detailed clearly
on the liquid crystal display. In
addition, a report is created making
it possible to enquire later as to all
such ‚interventions‘, each of which
is time-stamped.
The mains voltage is monitored
and displayed continuously, with
the devices adapting automatically
to 230 V, for example, or 120 V. At
the same time, the mains current
consumption is also monitored and
displayed. The trip value of the automatic circuit breakers can be set
by the user via the display of the
power amplifier to prevent the circuit breakers tripping. Any short-
PowerH Series
circuits at the output of the power
amplifier are detected early on,
even at low levels. The protective
circuit is activated and a report on
the fault in question appears simultaneously on the front display. In the
event of excessive high-frequency
overload, there is an automatic level
reduction to protect the power
amplifier itself and also the loudspeaker components connected.
The large, background-lit liquid
crystal display delivers comprehensive
status information, error reports
and measurements as well as
allowing you to control the basic
settings and (with the IRIS-Net
module integrated) select presets
as well.
In addition to extreme reliability
and forward-looking operating
security, the PowerH power amplifiers
are impressive for their outstanding
audio performance. The THD,
intermodulation distortion (IMDSMPTE) and dynamic intermodulation
(DIM) are well below 0.05% and
therefore well below the limit of
audibility. All the components of
the switching power supply are so
safely dimensioned that they are
capable of delivering the maximum
peak output current of 70 A continuously (H 5000), thereby allowing
the power amplifier to operate
as a stable voltage source even
with extremely low loads. PowerH
power amplifiers therefore have
a significant amount of headroom
at their disposal, which results in
superlative dynamics even with
low loads.
PowerH power amplifiers leave
nothing to be desired in terms of
connectivity. For the inputs, XLR
IN/parallel OUT sockets are provided
along with additional Phoenix
connectors. The input sensitivity is
switchable between 0dBu, +6dBu
and 32dB Constant Gain. In addition,
there are switches for Bridged
Mode and Parallel / Dual as well,
naturally, as a Ground Lift switch.
A latching PowerCon connector
is provided for the mains power
line, which prevents the plug
being yanked out accidentally. The
power outputs are implemented
as Speakon sockets. The signal of
Output B is additionally available on
pins ±2 of Output A, so that with
4-pin wiring a two-way system can
be driven. Parallel to these, additional binding posts are provided. In
terms of connectivity, therefore,
PowerH power amplifiers satisfy
all the demands of both mobile
applications and pro audio fixed
installations.
German engineering. Manufactured
in accordance with the Bosch Production System (BPS) in Straubing,
Germany.
17
Remote Control and IRIS-Net
Remote Control and IRIS-Net
IRIS-Net is the integrated software platform for all remote-
controllable devices and systems from DYNACORD and Electro-Voice.
Using IRIS-Net, complete audio
systems with a large number of
devices of the same or different
types can be configured, supervised
and controlled centrally from a
single user interface.
IRIS-Net supports Ethernet, CobraNet, CAN-Bus and USB as well as
being open to additional future
implementations. IRIS-Net makes
possible the complete supervision
of power amplifiers and loudspeakers
including their connecting cables
and interfaces.
System conditions are polled
continuously. Faults are detected
immediately and reported, with
all problems and events of other
18
kinds logged along with the date
and time at which they occurred.
All the parameters and settings
of all system components can be
saved and reloaded at the push of
a button (Total Recall). Depending
upon the application, users can
design their own control panels,
program automatic sequences,
and create groups of devices or
functions.
IRIS-Net has for several years already
been used in hundreds of audio
installations and systems and has
proved its value in a variety of
applications. IRIS-Net has also for
years been the platform for amplifiers
belonging to EV’s Precision series,
Netmax 8000 and the DYNACORD
P64 Digital Audio Matrix Manager.
The P64 is a modular, network-
capable audio system controller
with which structures of any kind
up to 32 audio channels can be
configured freely. As well as FIR
filters, a large number of DSP
functions with outstanding audio
quality (SNR > 115 dB) are available.
Its modular hardware and expandable
DSP capacity make the P64 the
perfect partner for all audio applications.
The RCM 810 (DSA series) and
RCM 26 (Power H) remote control
modules are also integrated into
the IRIS-Net platform.
RCM-26
RCM-26
Digital Controller Modul for Power H
The RCM-26 is a dual-channel digital controller
module for live sound, PA and fixed installation. It
offers all conventional signal processing functions
such as parametric equalizers, crossovers, delays,
compressors and limiters.
It also makes available linear phase FIR filters, zero-latency
FIR filters and digital loudspeaker protection algorithms
to permit the dynamic range of the amplifier to be
exploited to the full. In addition to the electronically
balanced analogue inputs of the power amplifier, digital
inputs in AES3 (AES/EBU) format are on board.
Using the CAN buss, networks of up to 250 power
amplifiers can be realized. Additional interfaces include
the RS-232 interface for medium control and the Control
Port with freely-programmable control inputs and
outputs (GPIO). Despite its compact dimensions,
the RCM-26 is unmatched in terms of its capabilities
and audio performance. The IRIS-Net Remote Control
Module RCM-26 extends the functionality of PowerH
power amplifiers by providing:
Remote Control
• AES3 (AES/EBU) digital inputs
• digital signal processing
• loudspeaker protection algorithms
• system integration and networking
• linear 24-bit AD/DA converters
• sigma-delta 128 x oversampling
• dynamic range > 116 dB
• 96 kHz sample rate, 48 kHz optional
• THD+N < 0.005%
• 2 DSPs 150 MHz / 300 MIPS computational power
• 48-bit double-precision algorithms
19
RCM-26
Supervision and diagnosis
The RCM-26 transmits all relevant amplifier data to
the IRIS-Net user interface, supervising the operating
status of the power amplifiers, the temperature in the
power blocks and in the power supply, voltages and
currents at the outputs, all protections, the mains
voltage and current consumption, pilot tone and network
status.
The impedance measurement with a 20Hz to 20 kHz
sine wave sweep and the comparison with the stored
reference data make it possible to diagnose with precision
the condition of the connected loudspeakers and
even of their individual components and cable connections. Problems are therefore detected early and the
system is able to respond in good time.
It is even easy to examine the state of loudspeakers
that are difficult to access, such as those in stadiums
or large entertainment venues. The System Check
20
function allows you to measure comprehensively,
and conduct a full examination of, a very large audio
system at the push of a button.
Even in live performance, the connected load is monitored continuously. Any undershooting (short-circuit)
or overshooting (interruption) of the set tolerance
limits is automatically detected and reported immediately.
FIR filters
Although FIR filters require a massive amount of processing and are complex, they are realized in the RCM-26 in
addition to the classical filtering and signal processing
functions. Both linear-phase FIR filters and ‚zero latency‘
FIR filters, which add no further delay to the time signals
take to pass through the device, are available.
Users can create their own linear phase ‚brick-wall
X-over‘ and edit them in real time. For DYNACORD
RCM-26
loudspeaker cabinets and systems, factory presets are
available with linear phase ‚brick-wall‘ FIR crossovers.
These provide users wishing to tune the system themselves
with a completely linearized frequency and phase response
upon which to build.
system frequency response in Display
For DYNACORD loudspeaker cabinets, measurements
of the frequency and phase response are already
provided in the IRIS-Net. This data together with the
filter, crossover and delay settings conducted in the
RCM-26 can be displayed and taken into account by
IRIS-Net. The superposition shows the actual frequency
response of the loudspeaker cabinet.
Remote functions
Remote control of the power amplifier under IRIS-Net
provides Power On / Standby switching and the
programming of power-up sequences for the power
amplifiers as well as level settings and the muting of
individual channels or channel groups. In the RCM-26,
all parameters can be controlled in real time as well
as stored in user memories, from which they can be
retrieved and reloaded subsequently.
DSP functions
• X-over: Linkwitz-Riley, Butterworth, Bessel
• FIR Filters: zero latency processing, linear phase X-over
• Master EQ: 6 filters per channel; PEQ, lo-shelf, hi-shelf, hi-pass, lo-pass selectable
• Channel EQ: 6 filters per channel; PEQ, lo-shelf,
hi-shelf, hi-pass, lo-pass, all-pass selectable
• Master delay : 2ms - 2000ms per channel
• Channel delay: speaker alignment
• Dynamics: compressor, limiter per channel
• Protection: Advanced Digital Voice Coil Protection algorithms
• Others: input routing, level, mute, polarity, sine and noise generators, VU meter
21
recommended applications
Live Music, ConcertSound, Touring
|
Pro Sound
Ultra Lightweight Premium
Audio Performance.
22
LX Series
LX
Power Amplifiers
··
··
··
··
LX 1600
LX 2200
LX 3000
XA 4000
23
LX Series
LX Series
ultra light weight power amplifiers
LX1600 • LX2200 • LX3000
Xa 4000
•
•
•
•
•
•
•
•
•
high-efficiency Class-H design
switching power supply
extremely light and compact
30% dynamic headroom
very high 2 ohm stability
complete package of protective circuits
dynamic audio limiter
precise raster pots on front panel
constant gain with 32dB
SWITCHING POWER SUPPLY TECHNOLOGY
The combination of an analogue
class-H design with a state-ofthe-art switching power supply
has made possible the creation
of a professional power amplifier
delivering up to 2 x 1500 watts
into 4 ohms with excellent audio
specifications but weighing only
8.7 kg. Even complex loads as low as
2 ohms can be driven safely. Amp
racks containing several LX power
amplifiers for active multi-way use
are therefore ultra-compact and
lightweight.
CLASS - H TECHNOLOGY
With this technology, two different
power supply rails are permanently
available internally to the power
24
amplifier blocks. For most of the
program material, the lower operating voltage is able to reproduce
the audio signal flawlessly; however,
as soon as there are dynamic
peaks, the amplifier switches
internally and at high speed to the
higher supply voltage.
Since for long periods the power
amplifier blocks are operating with
the lower supply voltage, there is
considerably less power dissipation
than with conventional class AB
power amplifiers, which also means
considerably less waste heat.
SAFETY CIRCUITS
The complete LX series is equipped
with protections against overheating,
overloading, short-circuits, DC and
HF as well as a Back-EMF protection.
With the Soft Start system, the power
outputs are switched on via a relay
when a safe operational state has
been reached and a power-up delay
prevents the mains fuses being
triggered.
German engineering. Manufactured
in accordance with the Bosch Production System (BPS) in Straubing,
Germany.
LX Series
25
LX Series
Were they to appear in a high-end hi-fi magazine, the measured values of the LX1600 would no doubt have the audiophiles
drooling. From every single discipline it’s evident that the people working in Dynacord’s development department in
Straubing are perfectionists in the best sense of the word.
LX 1600 Test in `Production Partner` 11/2008
FRONT PANEL
The dB-calibrated level controls are implemented as
ultra-precise detent potentiometers that are recessed
in the front panel to protect them from accidental
contact. Power, Protect, Signal and Limit LEDs provide
a quick overview of the operating status.
REAR PANEL
The electronically balanced XLR IN / OUT sockets are
provided for direct operation with professional mixing
consoles and signal processors. All the models in the
LX series are designed for a Constant Gain of 32 dB.
The power outputs for Channels A and B as well as
the Bridged Out are on Speakon connectors.
The signal of Output B is additionally available on pins
±2 of Output A, so that with 4-pin wiring a two-way
system can be driven. A Ground Lift switch is also provided to separate the chassis ground from the signal
ground in order to eliminate ground loop hum.
26
DYNAMIC LIMITERS
Dynamic limiters are general components in all
DYNACORD power amplifiers. High-speed audio
processors are continuously comparing the input signal
to the output signal, and in the event of any nonlinearity, the processors send control signals to the
limiters, which operate dynamically upon the input
level. As a result, the THD all the way up to 21 dBu is
limited to an inaudible 1% max. at the output.
LPN + LO-CUT
The retrofittable NRS 90268 kit, which is available
as an option for all LX power amplifiers, combines
the LPN (low-pass notch) filter with a low-cut filter.
These eliminate transient non-linearities in the low
frequency range in small to medium-sized full-range
speakers and thereby considerably extend the reproducible range at the bottom end. The acoustic result
is bass reproduction with more punch and greater
substance.
LX Series
LX 1600
With an output rated at 2 x 1300 watts into 2 ohms
and 2 x 800 watts into 4 ohms, this is the ideal power
amplifier for small to medium-sized full-range cabinets
and MF/HF components in active multi-way systems.
LX 2200
With a stable output of 2 x 1600 watts into 2 ohms
and 2 x 1100 watts into 4 ohms, this is the ideal
amplifier for professional multi-way components as
well as medium-sized subwoofers in concert sound
systems.
LX 3000
The flagship of the LX series delivers a mighty 2 x
2100 watts into 2 ohms and 2 x 1500 watts into 4 ohms
and therefore has plenty of headroom for large subwoofer arrays.
Xa 4000
Universally applicable system power amplifier for active
2-way systems. 1 x 1100 watts / 4 ohms (Lo) and 1 x
900 watts / 4 ohms (Hi). Crossover frequency 140 Hz
27
recommended applications
Live Music
|
Concert Sound, Club/Disco, Commercial
Superior Audio Performance, highest reliability and operational safety.
28
CL Series
Power Amplifiers
··
··
··
··
CL
CL
CL
CL
800
1200
1600
2000
29
CL Series
30
CL Series
CL Series
Thoroughbred workhorses for the most demanding audio tasks
TECHNOLOGY
Through the use of optimized power supplies with toroidal transformers
(on account of their low stray fields) and the intelligent application of
class H technology (CL 800: class AB), headroom way above the declared
nominal power has been achieved as well as a notable reduction in
weight and waste heat. CL power amplifiers satisfy the extreme demands
of life on the road and deliver between a nominal 2 x 400 watts and 2 x
1000 watts into 4 ohms. Even complex loads as low as 2 ohms can be
driven very saafely. Ranging in weight from only 13 kg to 18 kg, two or
more CL power amplifiers can be combined in racks that remain easy to
transport.
CLASS-H TECHNOLOGY
With this technology, two different power supply rails are permanently available
internally to the power amplifier blocks. For most of the program material, the
lower operating voltage is able to reproduce the audio signal flawlessly;
however, as soon as there are dynamic peaks, the amplifier switches
internally and at high speed to the higher supply voltage.
Since for long periods the power amplifier blocks are operating with
the lower supply voltage, there is considerably less power dissipation than
with conventional class AB power amplifiers, which also means considerably
less waste heat.
31
CL Series
FRONT PANEL
The dB-calibrated level controls are implemented as
ultra-precise detent potentiometers that are recessed
in the front panel to protect them from accidental
contact. Power, Protect, Signal and Limit LEDs provide
a quick overview of the operating status.
REAR PANEL
The electronically balanced XLR IN / OUT sockets
are provided for direct operation with professional
mixing consoles and signal processors. All the models
in the CL series are designed for a Constant Gain of
32 dB.
The power outputs for Channels A and B are on
Speakon connectors. The signal of Output B is additionally available on pins ±2 of Output A, so that
with 4-pin wiring a two-way system can be driven.
A Ground Lift switch is also provided to separate the
chassis ground from the signal ground in order to
eliminate ground loop hum.
SAFETY CIRCUITS
The complete CL series is equipped with protections
against overheating, overloading, short-circuits, DC
and HF as well as a Back-EMF protection. With the
Soft Start system, the power outputs are switched
on via a relay when a safe operational state has been
reached and a power-up delay prevents the mains
fuses being activated.
German engineering. Manufactured in accordance
with the Bosch Production System (BPS) in Straubing,
Germany.
32
CL Series
LPN + LO-CUT
The retrofittable NRS 90268 kit, which is available as
an option for all CL power amplifiers, combines the
patented LPN (low-pass notch) filter with a low-cut
filter.
+15
+10
+5
%
These eliminate transient non-linearity in the low
frequency range in small to medium-sized full-range
speakers and thereby considerably extend the reproducible range at the bottom end. The acoustic result
is bass reproduction with more punch and greater
substance.
DYNAMIC LIMITERS
Dynamic limiters are general components in all DYNACORD
power amplifiers. High-speed audio processors are
continuously comparing the input signal to the output signal, and in the event of any non-linearity, the
processors send control signals to the limiters, which
operate dynamically upon the input level.
+0
-5
-10
-15
20
50
100
200
500
1k
2k
5k
10k
20k
Hz
10
5
2
1
THD=1%
0.5
0.2
%
0.1
0.05
0.02
0.001
As a result, the THD all the way up to 21 dBU is limited to an inaudible 1% at the output.
0.005
21 dBu
0.002
-5
-3
-1
+1
+3
+5
+7
+9
+11
+13
+15
+17
+19
+21
+23
+25
dBu
CL 800
Rated at 2 x 600 watts into 2 ohms and 2 x 400 watts
into 4 ohms, the smallest power amplifier in the CL
series, which uses class AB technology, weighs in at
a mere 13 kg and is therefore the ideal amp for fairly
small full-range cabinets.
CL 1200
Delivering a reliable 2 x 900 watts into 2 ohms and
2 x 600 watts into 4 ohms, this is the ideal amplifier
for a wide variety of full-range cabinets and MF/HF
components in multi-way systems.
CL 1600
Rated at 2 x 1100 watts into 2 ohms and 2 x 800
watts into 4 ohms, this amplifier is ideal for use with
professional full-range cabinets and also passive
TOP/SUB combinations.
CL 2000
The flagship of the CL series delivers a beefy 2 x 1400
watts into 2 ohms and 2 x 1000 watts into 4 ohms,
whilst weighing a mere 18 kg. Ideal for driving large
subwoofer arrays as well as full-range and MID-HIGH
components with high power handling.
33
recommended applications
Live Music
|
Concert Sound, Commercial
Stable power output and a high
efficiency factor on the high
performance level.
34
SL Series
SL
Power Amplifiers
··
··
··
··
SL
SL
SL
SL
900
1200
1800
2400
35
SL Series
Solid DYNACORD technology
for universal application at highly
competitive prices was the
maxims for the development of
the SL series of power amplifiers.
They offer high, stable power
output and a high efficiency factor
on the high performance level and
are therefore the ideal choice for
driving a multitude of mobile and club
systems, such as e.g. loudspeakers
of the D-Lite, VariLine or Forum
Line families.
SL series power amplifiers are
equipped with protection against
overheating, overload, short-circuits, high frequencies and DC at
the output.
Damage to the end transistors
through the feedback of electrical
energy is prevented by the back
EMF protective circuitry.
When powering up, a relay delays
the switching on of the power outputs. In addition, a power-up current limiter prevents the blowing
of the mains fuses.
Fast audio processors continuously compare the input and output
signals. In the event of any nonlinearity, the processors send control signals to the limiters, which
dynamically reduce the input gain
of the power amplifier.
36
SL Series
SL Series
Solid all-rounders at a competitive price
The level controls on the front are calibrated in dB
and recessed into the front panel to guard against
mechanical damage. The easy-to-read LED display with
its Power, Protect, Signal and Limit indicators offers
a quick overview of the operating state of the power
amplifiers.
+12
+9
+6
transient behaviour of loudspeakers. The resulting
dynamization cannot be achieved with any graphic
or parametric equalizer or ‘bass booster’, since the
way the LPN operates is based to an important extent
upon a dynamic optimization of the slew rate of the
signal. The switch allows you to compare the acoustic
difference with and without the LPN. The whole
signal becomes much more powerful and voluminous.
The effect is particularly noticeable with small to
medium-sized full-range loudspeakers but also with
applications featuring subwoofers.
+3
+0
d
B
r
A
-3
-6
-9
-12
10
20
50
100
200
500
1k
2k
5k
10k
20k
50k
100k
Hz
LPN-Filter
The switchable Low-Pass Notch (LPN) filter is a typical DYNACORD special feature. This filter circuitry
corrects the frequency response and optimizes the
The electronically balanced XLR IN / OUT sockets are
provided for direct operation with professional mixing
consoles and signal processors. All the models in the
SL series are designed for a Constant Gain of 32 dB.
The power outputs for Channels A and B as well as
the Bridged Out are on Speakon connectors. The signal
of Output B is additionally available on pins ±2 of
Output A, so that with 4-pin wiring a two-way system
can be driven. A Ground Lift switch is also provided to
separate the chassis ground from the signal ground in
order to eliminate ground loop hum.
German engineering. Manufactured in accordance
with the Bosch Production System (BPS) in Zhuhai,
China
37
recommended applications
Multi Media, Club/Disco, Pro Sound, Commercial
|
Network
Universal installation power amplifiers with
optional network capability (IRIS-Net).
38
DSA Series
DSA
Power Amplifiers
··
··
··
··
··
··
··
DSA
DSA
DSA
DSA
DSA
DSA
DSA
8405
8410
8805
8204
8206
8209
8212
39
DSA Series - Multi-Channel
DSA Series - Multi-Channel
can drive any load between 2 and 10 ohms with their rated maximum outputs of 500 W and 1000 W respectively per channel
or directly drive 70 Vrms or 100 Vrms loudspeaker lines.
Innovative DYNACORD technology,
exemplary flexibility, very high
output with an extremely good
efficiency and integration into
IRIS-Net networks: a thumbnail
sketch of the DSA multi-channel
power amplifiers that provide a
multitude of solutions to the
problems posed by fixed installations.
German engineering. Manufactured
in accordance with the Bosch Production System (BPS) in Straubing,
Germany.
The multi-channel DSA 8405 / 8410 /
8805 power amplifiers are a milestone in the design and production of
high-powered power amplifiers. The
unique combination of Class D power
amplifier blocks and synchronized
switching power supplies offers to
this date unmatched power density
combined with excellent audio performance.
OUTPUT
2Ω : 500W/2Ω, VLD
4Ω : 500W/4Ω, 250W/8Ω
70V : 500W/10Ω
100V : 500W/20Ω
Unique flexibility through VLD
The ability to switch individually
the mode of each power amp channel helps the DSA multi-channel
power amplifiers to achieve a degree of flexibility never before possible. In low impedance operation
(2 Ω, 4 Ω, 8 Ω), each channel can
drive up to four 8-ohm loudspeaker
cabinets. The output channels can
also be paired in bridged mode.
40
DSA Series - Multi-Channel
Depending upon the application,
each channel can be switched individually even in high-impedance
mode (HZ) in order to drive 70
Vrms or 100 Vrms loudspeaker
lines directly without an output
transformer (Direct Drive).
The power output by the DSA
multi-channel power amplifiers is
(along with its thermal capacity)
limited only by their maximum
output voltage and maximum
output current, which means they
can drive any load between 2 and
10 ohms with their rated maximum
outputs of 500 W and 1000 W respectively per channel.
A corresponding encoder-circuit
is provided on the rear panel. In
addition, through VLD (Variable
Load Drive) in combination with
a RCM-810 remote control module,
it is possible to define freely
which output power should be
made available at which load in
the frame described above in the
channel in question: e.g. Channel
A = 350 W into 2.6 Ω; Channel B =
500 W into 8 Ω; Channel C = 200 W /
100V etc.
The fact that an output transformer has been dispensed with
the highly efficient Class-D power
amplifiers and switching power
supply yields an extremely attractive,
environment- and resource sparing
amplifier. For applications involving
mandatory galvanic separation of
the connected loudspeakers in
accordance with EN 60849 and
IEC 60364 separate transformer
modules are available, optionally.
Input level controls on the rear
panel as well as LED meters and
control indicators on the front
panel offer a high degree of user
comfort. It goes without saying
that all protective circuits and dynamic limiters (as is the case with
in all DYNACORD power amplifiers)
are available in every channel. Using
the ON DELAY selector switch
on the rear panel of the power
amplifier, you can set the interval
of time by which the switching
on process should be delayed. In
Standby mode, the power consumption of the device is reduced to a
minimum. Standby mode can be
activated via IRIS-Net or the POWER
REMOTE socket.
The Phoenix inputs marked INPUT are electronically balanced.
Phoenix connectors are also provided for the power outputs.
The POWER REMOTE connector
makes the task of remote controlling
the power amplifier as well as
switching it on and off simple. For
further remote-supervision and
–control possibilities and integration
into IRIS-Net networks, an optional
remote control module (RCM-810)
is available.
41
RCM-810
42
RCM-810
RCM-810
digital controller module
The RCM-810 remote control
module is a digital controller
module for PA and fixed installation
and permits the integration of
DSA amplifiers in a remote control
network with up to 250 devices.
With it, a complete PA system can
be controlled and supervised from
one or several PCs with the help
of IRIS-Net software. Data on all
operating states – e.g. switch-on
status, temperature, response
of protective circuits, load impedance etc. – is collected and
displayed centrally in IRIS-Net.
This makes it possible to react
with targeted intervention should
critical operating states ever occur.
It is also possible to program an
automatic reaction in the event
of certain threshold limits being
under- or overstepped. All parameters (e.g. Power On/Off, Mute etc.)
can be controlled in real time and
saved in the amplifier. Independently
of network control, all the settings
are saved in the event of a breakdown. The RCM-810 also offers a
Control Port with freely programmable
control inputs and outputs.
Switches can be connected to the
control inputs (GPIs). Within IRIS-Net,
you can program any desired logic
functions for the inputs.
External elements can be connected
to the control outputs (GPOs) in
order, for example, to signal particular
states. As a consequence, an amplifier
equipped with an RCM-810 module
satisfies the highest safety requirements.
German engineering. Manufactured
in accordance with the Bosch Production System (BPS) in Straubing,
Germany
43
DSA Series - Dual-Channel
44
DSA Series - Dual-Channel
DSA Series - Dual-Channel
amplifiers that provide a multitude of highly economic
solutions to the problems posed by fixed installations.
Solid DYNACORD technology
for fixed installations at very
competitive prices was the
maxims for the development of
the DSA power amplifier series.
They offer a very high, stable output with high efficiency at a high
performance level. DSA power
amplifiers are therefore the ideal
choice for typical fixed installation
applications.
They are protected against overheating, short circuit and both
high frequencies and DC at the
output. Damage to the end transistors
through the feedback of electrical
energy is prevented by the back
EMF protective circuitry. During
a soft start, a relay delays the
switching on of the power outputs.
In addition, a power-up current
limiter prevents the blowing of the
mains fuses. Fast audio processors
continuously compare the input
and output signals. In the event of
any non-linearity, the processors
send control signals to the limiters,
which dynamically reduce the input gain of the power amplifier.
Input level controls on the rear panel
and level and control displays on
the front panel offer a high degree
of user comfort, and a quick overview of the operating state of the
power amplifiers is provided by
the easily read LED display with its
Power, Protect, Signal Display and
Limit indicators.
A switchable high-pass filter (HPF)
(50 Hz, 18 dB/oct) can be used
to suppress low frequency signals,
which otherwise could lead to saturation of the transformers when output transformers are connected. A
Ground Lift switch is also provided
to separate the chassis ground
from the signal ground in order to
eliminate ground loop hum.
The POWER REMOTE connector
makes the task of remote controlling
the power amplifier as well as
switching it on and off simple.
For further remote-supervision and
–control possibilities and integration
into IRIS-Net networks, an optional
remote control module (RCM-810)
is available. (see pages 42-43)
German engineering. Manufactured
in accordance with the Bosch Production System (BPS) in Zhuhai,
China.
45
recommended applications
Commercial
Power amplifiers for challenging sound reinforcement.
46
PCL Series
PCL Series
··
··
··
··
··
PCL
PCL
PCL
PCL
PCL
1125T
1225T
1240T
1245
1415
47
PCL Series
PCL Series
contractor line power amplifiers
With the PCL series, DYNACORD
is adding to its extensive power
amplifier range in the fixed
installation segment a number of
models with fairly low to medium
output levels.
The power amplifiers are particularly
designed for challenging sound
reinforcement tasks, background
music / paging and public address
system installations. Long term reliability, operational safety, flexibility
and versatility are guaranteed.
The five models in the PCL series
offer a variety of system design
and implementation possibilities.
The PCL 1225T and PCL 1240T
are equipped with distortionfree
high performance output transformers and low-impedance outputs
48
at 8 / 4 ohms. Just like the PCL
1125T, they also provide floating
loudspeaker outputs for 50 V, 70 V
and 100 V installations. PCL 1245
and PCL 1415 are low-impedance
amplifiers with no output transformers. Premium Phoenix style
screw-lock connectors ensure a
more secure connection of audio
signal and speaker cables. The
independent rear level controls
allow setting the according power
amp channel’s overall amplification.
All PCL power amps feature different
hi-pass filters with switch selectable
cut-off frequency to attenuate
unwanted low frequency signals.
Provided by each of the PARAMUS
amplifier types are numerous
protection circuits (short circuit,
thermal overload, power on delay,
peak current limiters, to name a
few), which not only prevent the
power amplifier itself from being
damaged but protect the connected loudspeaker systems as well.
All PCL models offer excellent headroom for a wide dynamic range on
music signals.
They are equipped with voltage
limiters to protect the loudspeaker
outputs against high distortion
resulting in an output signal which
never exceeds a THD (total harmonic
distortion) of 1 %.
Multi-stage cooling fans additionally
guarantee absolute operational
reliability even at increased operating
temperatures.
German engineering. Manufactured
in Asia.
PCL Series
Features
• five models from 160 W to 450 W per
channel; 4 ohm or 50 / 70 / 100 V
• compact 2U housing
• Phoenix input plugs for simple setting-up
• single block plug for all output signals
• bridged mode for all multi-channel models
• switchable high-pass filter in each
channel; 50 Hz or 300 Hz
• level controller for each channel on the rear panel
• front-to-rear cooling
• numerous protective circuits
49
recommended applications
Network, Live Safety
|
ProSound
|
Multi Media, Commercial
Fixed installation power amplifiers with emergency
power capability and IRIS-Net integration.
50
DPA Series
DPA Series
··
··
··
··
··
··
··
··
··
DPA
DPA
DPA
DPA
DPA
DPA
DPA
DPA
DPA
4120
4140
4410
4411
4245
4260
8150
8225
8412
51
DPA Series
DPA Series
FINEST AUDIO QUALITY FOR ALARM SOUND REINFORCEMENT
Power amplifiers of the highest quality and
legendary reliability have for decades been a core
element of the DYNACORD fixed installation range.
Thousands upon thousands of DPA 4000 series
power amplifiers for example are proving their worth
every day in countless installations throughout the
globe—invariably leading in terms of performance,
equipment and flexibility and always conforming to
the safety regulations in force such as EN 60849,
DIN VDE 0828. Naturally these power amplifiers offer
ideal solutions for networking, remote supervision,
remote control, emergency power and all the other
imperatives of life safety projects.
The power amplifiers of the DPA 4000 series can be
operated either from the mains or from an emergency
power supply (e.g. battery). Power consumption is
minimal in Stand By mode—as little as 2.5 mA in some
cases. All the devices in the series boast outstanding
audio performance, with signal-to-noise ratios, for
example, in excess of 100 dB.
The DPA 4120 / DPA 4140 power amplifiers can be
fitted with either the standard input module or a remote
control module. Thus equipped, the amplifiers can be
both controlled and supervised remotely.
Thanks to the intelligent output circuitry of the DPA
4411 and DPA 4410, the power outputs can be configured
individually to deliver 4 x 100 W, 2 x 200 W or 1 x 200 W
plus 2 x 100 W, according to choice.
For power amplifiers to used also in alarm sound reinforcement systems it is necessary for them to report
any malfunctions. The flawless functioning of power
amplifiers in the DPA series is therefore permanently
supervised.
German development. Manufactured using the BPS
(Bosch Production System) in Straubing, Germany.
Features DPA 4000 Series:
• 6 models with 4 x 100 W, 1 x 200 W, 1 x 400 W, 2 x 450 W and 2 x 600 W
• 4 ohm or 50 / 70 / 100V
• Mains and 24V operation
• Power up current limiting
• Protective circuits
• Status LEDs
52
DPA Series
The new models of the DPA
8000 series are based on highly
efficient Class D platforms and
offer in addition to outstanding
audio performance features such
as integrated automatic breakdown switchover, integrated
electronics for the connection of
multiple loudspeaker lines per
amplifier channel, an additional
audio input, etc.
The Promatrix 8000 system, to
which the DPA 8000 amplifiers
also belong, sets new standards in
the integration of event, information
and evacuation sound reinforcement.
In the development of the DPA
8000 series, the emphasis was
upon the following primary characteristics: smaller dimensions coupled
with greater power, lower power
consumption, higher integration
of functions, and better audio performance. The outcome is a series
of models that meet the highest
demands of modern sound reinforce-
ment systems including evacuation
conformity. With a signal-to-noise
ratio of over 102 dB, the amplifiers
can be used without compromise
for pro sound applications.
Thanks to the permanent integrated
supervision, faults not only in the
amplifiers themselves but also in
the loudspeaker lines connected
are detected and reported immediately. For the supervision of the
loudspeaker lines, a choice is offered
of various methods, which can be
used singly or in combination.
The total power of 500 W in two
rack units is achieved with minimal
power dissipation, which means
savings, too, on external air conditioning.
Each of the amplifiers possesses
an additional audio input for the
playing of background music or
use as an emergency input. For the
connection of multiple loudspeaker
lines to a single amplifier channel,
the control electronics are already
integrated into the amplifier and
can be extended through the DCS
400 modular system.
It goes without saying that power
can be drawn either from the
mains or a battery and that all
devices offer power up current
limiting as well as additional protective circuitry.
German development. Manufactured using the BPS (Bosch
Production System) in Straubing,
Germany.
Features DPA 8000 Series:
• 3 models with 1 x 500 W,
2 x 250 W, 4 x 125 W
• Mains and 24V battery operation
• Lower power consumption
• Compact 2U format
• Power up current limiting
• Integrated breakdown switchover
• Integrated zone switching
• Protective circuits
• Status LEDs
53
Recommended Products / Application
Recommended Products / Application
RECOMMENDED PRODUCTS / APPLICATION
Mobile Audio
Live Music
Concert Sound
Fixed Installation
Touring
Multi Media
Boardrooms
Large Live
Corporate
Club-Gigs
Productions Conferencing
Rental
Dance Bands
Hotels
Mobile DJ Top 40 Events Small - Medium
Festival
Club/Disco
ProSound
Network
Commercial
Life Safety
Clubs
Lounges
Discotheques
Poolbars
Casinos
Theaters
Concert Halls
HOW
Stadiums
Cruise LIners
Multifunctional
Halls
Conference
Centers
Hotels
Business
Buildings
Arenas
Expo-Halls
Shops
Malls
Bistros
BGM
Voice-EVAC
Industry
Railway
Offshore
PowerH Series
LX Series
CL Series
SL Series
DSA Series
Multi Channel
Dual Channel
PCL Series
DPA Series
4000 Series
8000 Series
Perfect Solution
Excellent Choice
Suitable
In our multimedia world, professional audio systems are
playing an ever more important role. For this, power amplifiers
are needed the characteristics and properties of which are
tailored precisely to the application in question.
The spectrum of these requirements—from live music to fixed
installation—has an extremely wide bandwidth and extends from
very high power output combined with minimum weight to remote
supervision and network capability. DYNACORD’s extensive power
amplifier portfolio offers an ideal and cost-effective solution for
every field of application.
54
PowerH Series
PowerH 5000
PowerH Series
technical specifications
General
H 2500
2Ω
Load Impedance
H 5000
4Ω
8Ω
2Ω
4Ω
8Ω
Maximum Midband Output Power, 1 kHz, THD=1%
2000 W
1450 W
850 W
3500 W
2500 W
1500 W
Rated Output Power, 20 Hz ... 20 kHz, THD <0.1%
-
1200 W
600 W
-
2100 W
1050 W
Max. Single Channel Output Power Dynamic-Headroom, IHF-A
2400 W
1700 W
940 W
4500 W
3200 W
1800 W
Max. Single Channel Output Power Continuous, 1kHz
2050 W
1600 W
900 W
4100 W
2700 W
1600 W
-
3800 W
2900 W
-
7000 W
5000 W
Maximum Bridged Output Power 1 kHz, THD=1%
95 V
Maximum RMS Voltage Swing 1 kHz, THD=1%
125 V
10 Hz ... 50 kHz
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω
Voltage Gain ref. 1 kHz
Input Sensitivity at rated output power @ 8Ω, 1 kHz
39 dB / 35 dB / 32 dB (switchable)
41dB / 35 dB / 32 dB (switchable)
0 dBu / +4 dBu / +7 dBu (switchable)
0 dBu / +6 dBu / +9 dBu (switchable)
THD at rated output power MBW=80kHz, 1 kHz
< 0.05 %
IMD-SMPTE, 60 Hz, 7 kHz
< 0.05 %
DIM 30, 3.15 kHz, 15 kHz
< 0.02 %
+22 dBu (9,76 Vrms)
Max. Input Level
< -80 dB
Crosstalk, ref. 1 kHz at rated output power
Frequency Response, ref. 1 kHz
< 10 Hz ... 30 kHz (± 1dB)
Input Inpedance, active balanced
20 kΩ
Damping Factor ,1kHz
> 400
Slew Rate
30 V/µs
35V/µs
Signal to Noise Ratio Amplifier A-weighted, 32 dB constant gain
109 dB
111 dB
< -70 dBu
Output Noise , A-weighted
Class-H Grounded Bridge
Output Stage Topology
Power Requirements
100 V - 240 V, 50 Hz - 60 Hz; 100 V, 50 Hz - 60 Hz
Power Consumption at 1/8 maximum output power @ 4 Ω
1000 W
Protections
1450 W
Audio limiters, High temperature, DC, HF, Short Circuit, Back-EMF, Peak current
limiters, Inrush current limiters,Turn-on Delay, Mains Circuit Breaker Protection,
Mains Over / Undervoltage Protection
Cooling
Ambient Temperature Limits
Front-to-Rear, 5-stage-fans
+5°C ... +40°C (40°F ... 105°F)
I
Safety Class
483 x 88.1 x 498
Dimensions (WxHxD), mm
Weight
14.2 kg (31.1 lbs)
14.5 kg (32.0 lbs)
Amplifier at rated conditions, both channels driven with 8 Ω loads, unless otherwise specified
55
Xa 4000
Xa 4000
technical specifications
General
Load Impedance
Maximum Midband Output Power, THD=1%, 80Hz SUB, 1 kHz
TOP, Single Channel
Rated Output Power,
THD <0.1%, 20 Hz-140 Hz SUB, 140 Hz-20 kHz TOP Single
Channel
Maximum RMS Voltage Swing,
THD=1%, 80 Hz SUB, 1 kHz TOP
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω
Voltage Gain ref. 1 kHz
Input Sensitivity
at rated output power, 1 kHz
THD at rated output power, MBW=80kHz, 1 kHz
Max. Input Level
SUB
TOP
2Ω
4Ω
8Ω
2Ω
4Ω
8Ω
1800 W
1100 W
600 W
1600 W
900 W
500 W
-
1000 W
500 W
-
800 W
400 W
78 V
10 Hz ... 50 kHz
37.3 dB
0 dBu (0.775 V rms)
< 0.05 %
+22 dBu (9.76 Vrms)
Input Inpedance, active balanced
20 kΩ
Damping Factor ,1kHz
> 300
Slew Rate
30 V/µs
Signal to Noise Ratio, A-weighted
102 dB
Output Stage Topology
Power Requirements
Power Consumption at 1/8 maximum output power @ 4 Ω
Protections
Cooling
Ambient Temperature Limits
Safety Class
Class-H
240 V, 230 V, 220 V, 120 V or 100 V, 50 Hz... 60 Hz (factory configured)
850 W
Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush current
limiters,Turn-on delay
Front-to-Rear, 3-stage-fans
+5°C ... +40°C (40°F ... 105°F)
I
Dimensions (WxHxD), mm
483 x 88.1 x 384
Weight
8.25 kg (18.2 lbs)
Optional Accesories:
Rear Rackmount 15.5“: D112 930 (RMS15-CL)
Rear Rackmount 18.0“: D112 933 (RMS18-CL)
Xa 4000
56
LX Series
LX 2200
LX Series
technical specifications
General
LX 1600
LX 2200
LX 3000
2Ω
4Ω
8Ω
2Ω
4Ω
8Ω
2Ω
4Ω
8Ω
1300 W
800 W
500 W
1600 W
1100 W
600 W
2100 W
1500 W
900 W
-
700 W
350 W
-
900 W
450 W
-
1200 W
600 W
Max. Single Channel Output
Power Dynamic-Headroom, IHF-A
2200 W
1200 W
625 W
2600 W
1400 W
720 W
2900 W
1800 W
1000 W
Max. Single Channel Output
Power Continuous, 1kHz
1700 W
1000 W
550 W
2100 W
1300 W
660 W
2600 W
1700 W
950 W
-
2600 W
1600 W
-
3200 W
2200 W
-
4200 W
3000 W
Load Impedance
Maximum Midband Output Power,
1 kHz, THD=1%
Rated Output Power,
20 Hz ... 20 kHz, THD <0.1%
Maximum Bridged Output Power
1 kHz, THD=1%
Maximum RMS Voltage Swing
1 kHz, THD=1%
72 V
78 V
10 Hz ... 60 kHz
Power Bandwidth, THD=1%, ref.
1kHz, half power @ 4Ω
32 dB
Voltage Gain ref. 1 kHz
Input Sensitivity at rated
output power @ 8Ω, 1 kHz
+4.7 dBu (1.33 V rms)
+5.8 dBu (1.51 V rms)
THD at rated
output power MBW=80kHz, 1 kHz
< 0.05 %
IMD-SMPTE, 60 Hz, 7 kHz
< 0.02 %
DIM 30, 3.15 kHz, 15 kHz
< 0.05 %
< -80 dB
Crosstalk, ref. 1 kHz at
rated output power
Frequency Response, ref. 1 kHz
15 Hz ... 40 kHz (- 1dB)
Input Inpedance, active balanced
20 kΩ
> 300
Damping Factor ,1kHz
Slew Rate
30 V/µs
Signal to Noise Ratio, A-weighted
107 dB
38V/µs
107 dB
108 dB
100 V, 120V, 220V, 230V, 240V, 50 Hz... 60 Hz (factory configured)
Power Requirements
625 W
850 W
1070 W
Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush current limiters,Turn-on delay
Front-to-Rear, 3-stage-fans
Cooling
+5°C ... +40°C (40°F ... 105°F)
Ambient Temperature Limits
I
Safety Class
483 x 88.1 x 384
Dimensions (WxHxD), mm
Weight
35V/µs
Class-H
Output Stage Topology
Protections
+7.0 dBu (1.74 V rms)
+22 dBu (9.76 Vrms)
Max. Input Level
Power Consumption at 1/8 maximum output power @ 4 Ω
95 V
7.8 kg (17.2 lbs)
8.15 kg (18.0 lbs)
8.7 kg (19.2 lbs)
Optional Accesories:
Rear Rackmount 15.5“: D112 930 (RMS15-CL)
Rear Rackmount 18.0“: D112 933 (RMS18-CL)
LPN + Lo-Cut Filter: D112963 (NRS 90268)
57
CL Series
CL Series
technical specifications
General
Load Impedance
CL 800
2Ω
CL 1200
4Ω
8Ω
2Ω
4Ω
8Ω
Maximum Midband Output Power, 1 kHz, THD=1%
600 W
400 W
240 W
900 W
600 W
350 W
Rated Output Power, 20 Hz ... 20 kHz, THD <0.1%
-
300 W
150 W
-
500 W
250 W
Max. Single Channel Output Power
Dynamic-Headroom, IHF-A
1100 W
580 W
300 W
1450 W
850 W
450 W
Max. Single Channel Output Power Continuous, 1kHz
800 W
480 W
270 W
1200 W
720 W
410 W
-
1200 W
800 W
-
1800 W
1200 W
Maximum Bridged Output Power 1 kHz, THD=1%
Maximum RMS Voltage Swing 1 kHz, THD=1%
50 V
62 V
10 Hz ... 60 kHz
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω
32 dB
Voltage Gain ref. 1 kHz
Input Sensitivity at rated output power @ 8Ω, 1 kHz
+1.15 dBu (0.88 V rms)
+3.2 dBu (1.12 V rms)
THD at rated output power MBW=80kHz, 1 kHz
< 0.05 %
IMD-SMPTE, 60 Hz, 7 kHz
< 0.02 %
DIM 30, 3.15 kHz, 15 kHz
< 0.01 %
+22 dBu (9,76 Vrms)
Max. Input Level
< -80 dB
Crosstalk, ref. 1 kHz at rated output power
Frequency Response, ref. 1 kHz
15 Hz ... 40 kHz (- 1dB)
Input Inpedance, active balanced
20 kΩ
> 300
Damping Factor, 1kHz
25 V/µs
30 V/µs
Signal to Noise Ratio, A-weighted
103.5 dB
105.5 dB
Output Stage Topology
Class-AB
Class-H
Slew Rate
Power Requirements
Power Consumption at 1/8 maximum output power @ 4 Ω
Protections
100 V, 120V, 220V, 230V, 240V, 50 Hz... 60 Hz (factory configured)
600 W
Front-to-Rear, 3-stage-fans
Cooling
+5°C ... +40°C (40°F ... 105°F)
Ambient Temperature Limits
I
Safety Class
483 x 88.1 x 386.8
Dimensions (WxHxD), mm
Weight
Optional Accesories:
Rear Rackmount 15.5“: D112 930 (NRS90262)
Rear Rackmount 18.0“: D112 933 (NRS90264)
LPN + Lo-Cut Filter: D112963 (NRS 90268)
58
500 W
Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush current limiters,
Turn-on delay
13.5 kg (29.8 lbs)
15 kg (33.0 lbs)
CL Series
CL 1600
General
CL 1600
CL 2000
2Ω
4Ω
8Ω
2Ω
4Ω
Maximum Midband Output Power, 1 kHz, THD=1%
1100 W
800 W
500 W
1500 W
1000 W
600 W
Rated Output Power, 20 Hz ... 20 kHz, THD <0.1%
-
700 W
350 W
-
850 W
450 W
Max. Single Channel Output Power
Dynamic-Headroom, IHF-A
2200 W
1200 W
625 W
2700 W
1450 W
750 W
Max. Single Channel Output Power Continuous, 1kHz
1500 W
950 W
550 W
1900 W
1150 W
650 W
-
2200 W
1600 W
-
3000 W
2000 W
Load Impedance
Maximum Bridged Output Power 1 kHz, THD=1%
Maximum RMS Voltage Swing 1 kHz, THD=1%
72 V
80 V
10 Hz ... 60 kHz
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω
32 dB
Voltage Gain ref. 1 kHz
Input Sensitivity at rated output power @ 8Ω, 1 kHz
+4.7 dBu (1.33 V rms)
+5.5 dBu (1.46 V rms)
THD at rated output power MBW=80kHz, 1 kHz
< 0.05 %
IMD-SMPTE, 60 Hz, 7 kHz
< 0.02 %
DIM 30, 3.15 kHz, 15 kHz
< 0.01 %
+22 dBu (9.76 Vrms)
Max. Input Level
< -80 dB
Crosstalk, ref. 1 kHz at rated output power
Frequency Response, ref. 1 kHz
15 Hz ... 40 kHz (- 1dB)
Input Inpedance, active balanced
20 kΩ
> 300
Damping Factor, 1kHz
Slew Rate
35 V/µs
Signal to Noise Ratio, A-weighted
107 dB
Power Consumption at 1/8 maximum output power @ 4 Ω
Protections
109 dB
100 V, 120V, 220V, 230V, 240V, 50 Hz... 60 Hz (factory configured)
660 W
725 W
Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush current limiters,
Turn-on Delay
Front-to-Rear, 3-stage-fans
Cooling
+5°C ... +40°C (40°F ... 105°F)
Ambient Temperature Limits
I
Safety Class
483 x 88.1 x 386.8
Dimensions (WxHxD), mm
Weight
35 V/µs
Class-H
Output Stage Topology
Power Requirements
8Ω
16 kg (35.3 lbs)
18.2 kg (39.7 lbs)
Optional Accesories:
Rear Rackmount 15.5“: D112 930 (NRS90262)
Rear Rackmount 18.0“: D112 933 (NRS90264)
LPN + Lo-Cut Filter: D112963 (NRS 90268)
59
SL Series
SL Series
technical specifications
General
SL 900
SL 1200
2Ω
4Ω
8Ω
2Ω
4Ω
8Ω
650 W
450 W
270 W
900 W
600 W
380 W
-
400 W
200 W
-
500 W
250 W
Max. Single Channel Output Power Dynamic-Headroom, IHF-A
1150 W
660 W
350 W
1700 W
950 W
480 W
Max. Single Channel Output Power Continuous, 1kHz
850 W
540 W
310 W
1200 W
750 W
420 W
1300 W
900 W
-
1800 W
1200 W
Load Impedance
Maximum Midband Output Power, 1 kHz, THD=1%, Dual Channel
Rated Output Power, 20 Hz ... 20 kHz, THD <0.1%
Maximum Bridged Output Power 1 kHz, THD=1%
Maximum RMS Voltage Swing 1 kHz, THD=1%
-
55.3 V
65.1 V
10 Hz ... 30 kHz
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω
32 dB
Voltage Gain ref. 1 kHz
Input Sensitivity at rated output power @ 8Ω, 1 kHz
+2.2 dBu (1.0 V rms)
+3.1 dBu (1.11 V rms)
< 0.03 %
THD at rated output power MBW=80kHz, 1 kHz
IMD-SMPTE, 60 Hz, 7 kHz
< 0.1 %
DIM 30, 3.15 kHz, 15 kHz
< 0.05 %
+21 dBu (8.69 Vrms)
Max. Input Level
< -80 dB
Crosstalk, ref. 1 kHz at rated output power
Frequency Response, ref. 1 kHz
10 Hz ... 40 kHz (± 1dB)
Input Inpedance, active balanced
20 kΩ
Damping Factor, 1kHz
> 300
Slew Rate
25 V/µs
26 V/µs
Signal to Noise Ratio, A-weighted
106 dB
107 dB
Output Noise, A-weighted
< -71 dBu
Output Stage Topology
Class-AB
Power Requirements
Power Consumption at 1/8 maximum output power @ 4 Ω
Mains Fuse
Protections
Cooling
Ambient Temperature Limits
100 V, 120V, 230V, 240V, 50 Hz... 60 Hz (factory configured)
550 W
700 W
240V / 230V: T10AH,
120V / 100V: T20AH
240V / 230V: T12AH,
120V / 100V: T25AH
Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush
current limiters,Turn-on delay
Front-to-Rear, 3-stage-fans
+5°C ... +40°C (40°F ... 105°F)
I
Safety Class
483 x 88.1 x 421.5
Dimensions (WxHxD), mm
Weight
Optional Accesories:
2-Way crossover, internal filter card, 24dB, LR
330Hz (NRS 90249), 500Hz (NRS 90250)
800Hz (NRS 90251), 1200Hz (NRS 90252)
60
12.6 kg (27.8 lbs)
14.8 kg (32.6 lbs)
SL Series
SL 1200
General
SL 1800
SL 2400
2Ω
4Ω
8Ω
2Ω
4Ω
8Ω
1250 W
900 W
550 W
1800 W
1200 W
750 W
-
800 W
400 W
-
1100 W
550 W
Max. Single Channel Output Power Dynamic-Headroom, IHF-A
2450 W
1400 W
700 W
3400 W
1800 W
950 W
Max. Single Channel Output Power Continuous, 1kHz
1700 W
1100 W
630 W
2400 W
1500 W
850 W
2800 W
1800 W
-
3600 W
2400 W
Load Impedance
Maximum Midband Output Power, 1 kHz, THD=1%, Dual Channel
Rated Output Power, 20 Hz ... 20 kHz, THD <0.1%
Maximum Bridged Output Power 1 kHz, THD=1%
Maximum RMS Voltage Swing 1 kHz, THD=1%
-
78.8 V
90.6 V
10 Hz ... 30 kHz
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω
32 dB
Voltage Gain ref. 1 kHz
Input Sensitivity at rated output power @ 8Ω, 1 kHz
+5.1 dBu (1.39 Vrms)
+6.6 dBu (1.66 Vrms)
< 0.03 %
THD at rated output power MBW=80kHz, 1 kHz
IMD-SMPTE, 60 Hz, 7 kHz
< 0.1 %
DIM 30, 3.15 kHz, 15 kHz
< 0.05 %
+21 dBu (8.69 Vrms)
Max. Input Level
< -80 dB
Crosstalk, ref. 1 kHz at rated output power
Frequency Response, ref. 1 kHz
10 Hz ... 40 kHz (± 1dB)
Input Inpedance, active balanced
20 kΩ
Damping Factor, 1kHz
> 300
Slew Rate
27 V/µs
30 V/µs
Signal to Noise Ratio, A-weighted
109 dB
110 dB
< -71 dBu
Output Noise, A-weighted
Class-H
Output Stage Topology
Power Requirements
Power Consumption at 1/8 maximum output power @ 4 Ω
Mains Fuse
Protections
Cooling
Ambient Temperature Limits
100 V, 120V, 230V, 240V, 50 Hz... 60 Hz (factory configured)
700 W
850 W
240V / 230V: T15AH,
120V / 100V: T25AH
240V / 230V: T15AH,
120V / 100V: T30AH
Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush
current limiters,Turn-on delay
Front-to-Rear, 3-stage-fans
+5°C ... +40°C (40°F ... 105°F)
I
Safety Class
483 x 88.1 x 421.5
Dimensions (WxHxD), mm
Weight
16.3 kg (35.9 lbs)
17.7 kg (39.0 lbs)
Optional Accesories:
2-Way crossover, internal filter card, 24dB, LR
330Hz (NRS 90249), 500Hz (NRS 90250)
800Hz (NRS 90251), 1200Hz (NRS 90252)
61
DSA Series - Multi-Channel
DSA Series - Multi-Channel
technical specifications
General
DSA 8405
DSA 8805
2Ω
4Ω
8Ω
70 V /
10Ω
100 V /
20Ω
2Ω
4Ω
8Ω
70 V /
10Ω
100 V /
20Ω
Maximum Midband Output
Power, 1 kHz, THD=1%,
4 channels driven
500 W
500 W
250 W
VLD:500 W
500 W
500 W
500 W
500 W
250 W
VLD:500 W
500 W
500 W
Rated Output Power,
20 Hz ... 20 kHz, THD <0.3%, 4
channels driven
450 W
450 W
225 W
VLD:450 W
450 W
450 W
450 W
450 W
225 W
VLD:450 W
450 W
450 W
-
1000 W
1000 W
1000 W /
20 Ω
1000 W /
40 Ω
-
1000 W
1000 W
1000 W
/ 20 Ω
1000 W
/ 40 Ω
70 V
100 V
32 V
45 V
70 V
100 V
0.775 V
(+0.0 dBu)
1.1 V
(+3.0 dBu)
Load Impedance
Maximum Bridged Output Power
1 kHz, THD=1%
Maximum RMS Voltage Swing
1 kHz, THD=1%
Input Sensitivity,
rated power, 1 kHz
32 V
45 V
0.775 V
(+0.0 dBu)
1.1 V
(+3.0 dBu)
1.55 V
(+6.0 dBu)
10 Hz ... 25 kHz
Power Bandwidth, THD=1%,
ref. 1kHz, half power @ rated load
50 Hz ... 25 kHz
32 dB
Voltage Gain ref. 1 kHz
33 dB
10 Hz ... 25 kHz
36 dB
< 0.05 %
IMD-SMPTE, 60 Hz, 7 kHz
< 0.05 %
DIM 30, 3.15 kHz, 15 kHz
< 0.02 %
15 Hz ... 30 kHz (± 1dB)
Frequency Response,
ref. 1 kHz, 8 Ω load
Input Inpedance, active balanced
20 kΩ
Damping Factor, 1kHz, 8 Ω
> 240
28 V/µs
Slew Rate
98 dB
100 dB
104 dB
106 dB
98 dB
100 dB
104 dB
106 dB
< -66 dBu
< -65 dBu
< -65 dBu
< -64 dBu
< -66 dBu
< -65 dBu
< -65
dBu
< -64
dBu
Class-D
Output Stage Topology
Power Requirements
Power Consumption
at 1/8 maximum output
Protections
220-240V, 50-60 Hz or 120 V, 50-60 Hz or 100 V, 50-60 Hz
490 W
Front-to-Rear, temperature controlled fans
+5 °C...+40 °C (40 °F...105 °F)
Ambient Temperature Limits
I
Safety Class
481 x 88.0 x 421
Dimensions (WxHxD), mm
62
930 W
Audio Limiters, High Temperature, DC, HF, Short Circuit, Peak Current Limiters, Inrush Current Limiters, Turn-on Delay, Mains
Circuit Breaker Protection, Mains Over/Undervoltage Protection
Cooling
Weight
36 dB
< -80 dB
Crosstalk,
ref. 1 kHz at rated output power
Output Noise, A-weighted
33 dB
+22 dBu (9.76 Vrms)
Max. Input Level
Signal to Noise Ratio, A-weighted
50 Hz ... 25 kHz
32 dB
THD at rated output power
MBW=80kHz, 1 kHz
1.55 V
(+6.0 dBu)
11.1 kg (24.3 lbs)
13.9 kg (28.7 lbs)
DSA Series - Multi-Channel
DSA 8805
General
DSA 8410
2Ω
4Ω
8Ω
70 V /
5Ω
100 V /
10Ω
Maximum Midband Output Power, 1 kHz, THD=1%, 4 channels driven
1000 W
1000 W
500 W
VLD:1000 W
1000 W
1000 W
Rated Output Power, 20 Hz ... 20 kHz, THD <0.3%, 4 channels driven
900 W
900 W
450 W
VLD:900 W
900 W
900 W
-
2000 W
2000 W
2000 W / 10 Ω
2000 W /20 Ω
70 V
100 V
Load Impedance
Maximum Bridged Output Power
1 kHz, THD=1%
Maximum RMS Voltage Swing
1 kHz, THD=1%
Input Sensitivity, rated power, 1 kHz
45 V
63 V
1.1 V
(+3.0 dBu)
1.55 V
(+6.0 dBu)
1.55 V
(+6.0 dBu)
10 Hz ... 25 kHz
Power Bandwidth, THD=1%, ref. 1kHz, half power @ rated load
50 Hz ... 25 kHz
32 dB
Voltage Gain ref. 1 kHz
33 dB
THD at rated output power
MBW=80kHz, 1 kHz
< 0.05 %
IMD-SMPTE, 60 Hz, 7 kHz
< 0.05 %
< 0.02 %
DIM 30, 3.15 kHz, 15 kHz
+22 dBu (9.76 Vrms)
Max. Input Level
Crosstalk, ref. 1 kHz at rated output power
< -80 dB
Frequency Response, ref. 1 kHz, 8 Ω load
15 Hz ... 30 kHz (± 1dB)
20 kΩ
Input Inpedance, active balanced
> 240
Damping Factor, 1kHz, 8 Ω
28 V/µs
Slew Rate
Signal to Noise Ratio, A-weighted
Output Noise, A-weighted
Output Stage Topology
101 dB
103 dB
104 dB
106 dB
< -66 dBu
< -65 dBu
< -65 dBu
< -64 dBu
Class-D
Power Requirements
220-240V, 50-60 Hz or 120 V, 50-60 Hz or 100 V, 50-60 Hz
Power Consumption
at 1/8 maximum output
840 W
Protections
Cooling
Ambient Temperature Limits
Safety Class
36 dB
Audio Limiters, High Temperature, DC, HF, Short Circuit, Peak Current Limiters, Inrush Current
Limiters, Turn-on Delay, Mains Circuit Breaker Protection, Mains Over/Undervoltage Protection
Front-to-Rear, temperature controlled fans
+5 °C...+40 °C (40 °F...105 °F)
I
Dimensions (WxHxD), mm
481 x 88.0 x 421
Weight
11.1 kg (24.3 lbs)
63
DSA Series - Dual-Channel
DSA Series - Dual-Channel
technical specifications
General
DSA 8204
DSA 8206
2Ω
4Ω
8Ω
2Ω
4Ω
8Ω
650 W
450 W
270 W
900 W
600 W
380 W
-
400 W
200 W
-
500 W
250 W
Max. Single Channel Output Power Dynamic-Headroom, IHF-A
1150 W
660 W
350 W
1700 W
950 W
480 W
Max. Single Channel Output Power Continuous, 1kHz
850 W
540 W
310 W
1200 W
750 W
420 W
-
1300 W
900 W
-
1800 W
1200 W
Load Impedance
Maximum Midband Output Power, 1 kHz, THD=1%, Dual Channel
Rated Output Power, 20 Hz ... 20 kHz, THD <0.1%
Maximum Bridged Output Power 1 kHz, THD=1%
Maximum RMS Voltage Swing 1 kHz, THD=1%
55.3 V
65.1 V
10 Hz ... 30 kHz
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω
32 dB
Voltage Gain ref. 1 kHz
Input Sensitivity at rated output power @ 8Ω, 1 kHz
+2.2 dBu (1.0 V rms)
+3.1 dBu (1.11 V rms)
< 0.03 %
THD at rated output power MBW=80kHz, 1 kHz
IMD-SMPTE, 60 Hz, 7 kHz
< 0.1 %
DIM 30, 3.15 kHz, 15 kHz
< 0.05 %
+21 dBu (8.69 Vrms)
Max. Input Level
< -80 dB
Crosstalk, ref. 1 kHz at rated output power
Frequency Response, ref. 1 kHz
10 Hz ... 40 kHz (± 1dB)
Input Inpedance, active balanced
20 kΩ
Damping Factor, 1kHz
> 300
Slew Rate
25 V/µs
26 V/µs
Signal to Noise Ratio, A-weighted
106 dB
107 dB
Output Noise, A-weighted
< -71 dBu
Output Stage Topology
Class-AB
Power Requirements
Power Consumption at 1/8 maximum output power @ 4 Ω
Mains Fuse
Protections
100 V, 120V, 230V, 240V, 50 Hz... 60 Hz (factory configured)
550 W
700 W
240V / 230V: T10AH,
120V / 100V: T20AH
240V / 230V: T12AH,
120V / 100V: T25AH
Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters,
Inrush current limiters,Turn-on delay
Front-to-Rear, 3-stage-fans
Cooling
Ambient Temperature Limits
+5°C ... +40°C (40°F ... 105°F)
I
Safety Class
483 x 88.1 x 421.5
Dimensions (WxHxD), mm
Weight
12.6 kg (27.8 lbs)
14.8 kg (32.6 lbs)
Remote Power On
Power remote via switch, delay time selectable
Signal Processing
Lo-Cut 50Hz / 18dB, switchable
Optional Accesories:
2-Way crossover, internal filter card, 24dB, LR
330Hz (NRS 90249), 500Hz (NRS 90250)
800Hz (NRS 90251), 1200Hz (NRS 90252)
64
DSA Series - Dual-Channel
DSA 8212
General
DSA 8209
DSA 8212
2Ω
4Ω
8Ω
2Ω
4Ω
8Ω
1250 W
900 W
550 W
1800 W
1200 W
750 W
-
800 W
400 W
-
1100 W
550 W
Max. Single Channel Output Power Dynamic-Headroom, IHF-A
2450 W
1400 W
700 W
3400 W
1800 W
950 W
Max. Single Channel Output Power Continuous, 1kHz
1700 W
1100 W
630 W
2400 W
1500 W
850 W
-
2800 W
1800 W
-
3600 W
2400 W
Load Impedance
Maximum Midband Output Power, 1 kHz, THD=1%, Dual Channel
Rated Output Power, 20 Hz ... 20 kHz, THD <0.1%
Maximum Bridged Output Power 1 kHz, THD=1%
Maximum RMS Voltage Swing 1 kHz, THD=1%
78.8 V
90.6 V
10 Hz ... 30 kHz
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω
32 dB
Voltage Gain ref. 1 kHz
Input Sensitivity at rated output power @ 8Ω, 1 kHz
+5.1 dBu (1.39 Vrms)
+6.6 dBu (1.66 Vrms)
< 0.03 %
THD at rated output power MBW=80kHz, 1 kHz
IMD-SMPTE, 60 Hz, 7 kHz
< 0.1 %
DIM 30, 3.15 kHz, 15 kHz
< 0.05 %
+21 dBu (8.69 Vrms)
Max. Input Level
< -80 dB
Crosstalk, ref. 1 kHz at rated output power
Frequency Response, ref. 1 kHz
10 Hz ... 40 kHz (± 1dB)
Input Inpedance, active balanced
20 kΩ
Damping Factor, 1kHz
> 300
Slew Rate
27 V/µs
30 V/µs
Signal to Noise Ratio, A-weighted
109 dB
110 dB
< -71 dBu
Output Noise, A-weighted
Class-H
Output Stage Topology
Power Requirements
Power Consumption at 1/8 maximum output power @ 4 Ω
Mains Fuse
Protections
100 V, 120V, 230V, 240V, 50 Hz... 60 Hz (factory configured)
700 W
850 W
240V / 230V: T15AH,
120V / 100V: T25AH
240V / 230V: T15AH,
120V / 100V: T30AH
Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters,
Inrush current limiters,Turn-on delay
Front-to-Rear, 3-stage-fans
Cooling
Ambient Temperature Limits
+5°C ... +40°C (40°F ... 105°F)
I
Safety Class
483 x 88.1 x 421.5
Dimensions (WxHxD), mm
Weight
16.3 kg (35.9 lbs)
17.7 kg (39.0 lbs)
Remote Power On
Power remote via switch, delay time selectable
Signal Processing
Lo-Cut 50Hz / 18dB, switchable
Optional Accesories:
2-Way crossover, internal filter card, 24dB, LR
330Hz (NRS 90249), 500Hz (NRS 90250)
800Hz (NRS 90251), 1200Hz (NRS 90252)
65
PCL Series
PCL Series
technical specifications
PCL 1125T
General
PCL 1415
PCL 1245
PCL 1240T
8Ω
4Ω
8Ω
4Ω
8Ω
4Ω
Max. Midband Output
(THD < 0.2 %, 20 Hz…20 kHz)
100 W
160 W
300 W
480 W
215 W
430 W
430 W
Rated Output Power
(THD < 0.2 %, 20 Hz…20 kHz)
75 W
150 W
225 W
450 W
200 W
400 W
400W
Load Impedance
100 V
70 V
50 V
4
2
Max. RMS Voltage Swing
(THD = 1 %, 1 kHz)
32.1 V
44.7 V
44.7 V
117 V
82 V
59 V
Voltage Gain (at 1 kHz)
30 dB
34.3 dB
34.3 dB
42.2 dB
39.1 dB
36.2 dB
545 W
-
-
Channels
Power Handling (at 1/8 max. output power, limited pink)
-
385 W
-
2
530W
< 10 Hz – 40 kHz
65 Hz – 40 kHz
> 20 kΩ
Input Impedance
(20 Hz…20 kHz symmetr.)
> 250
Damping Factor
(at 100 Hz / 1 kHz, 4 Ω)
Signal to Noise Ratio S/N (A-weighted)
101 dB
> 250
104 dB
103 dB
audio limiters, thermal overload, peak current limiters, power-on delay
Protection
front to rear
Cooling
I
Safety Class
483 x 88 x 405 mm, 19” / 2 HU
Dimensions (WxHxD), mm
66
-
230 V / 50 Hz – 60 Hz
Power Requirements
Weight
-
< 0.1 %
THD (MBW = 80 kHz, 1 kHz)
Frequency Response
(-1 dB, ref. 1 kHz)
0 dBu (775 mV)
Input Sensitivity
(at ROP or Voltage, 1 kHz)
18 kg
16.5 kg
26 kg
PCL Series
PCL 1415
General
PCL 1225T
8Ω
4Ω
Max. Midband Output
(THD < 0.2 %, 20 Hz…20 kHz)
135 W
270 W
Rated Output Power
(THD < 0.2 %, 20 Hz…20 kHz)
125 W
250 W
Load Impedance
100 V
PCL 1125T
70 V
50 V
100 V
270 W
250 W
40 Ω
50 V
270 W
250 W
19.6 Ω
250 W
10 Ω
250 W
40 Ω
250 W
19.6 Ω
2
Channels
70 V
250 W
40 Ω
1
Max. RMS Voltage Swing
(THD = 1 %, 1 kHz)
35.4 V
117 V
82 V
59 V
117 V
82 V
59 V
Voltage Gain (at 1 kHz)
32.2 dB
42.2 dB
39.1 dB
36.2 dB
42.2 dB
39.1 dB
36.2 dB
-
-
170 W
-
-
Power Handling (at 1/8 max. output power, limited pink)
-
-
330 W
0 dBu (775 mV)
Input Sensitivity
(at ROP or Voltage, 1 kHz)
< 0.1 %
THD (MBW = 80 kHz, 1 kHz)
65 Hz – 40 kHz
Frequency Response
(-1 dB, ref. 1 kHz)
> 20 kΩ
Input Impedance
(20 Hz…20 kHz symmetr.)
Damping Factor
(at 100 Hz / 1 kHz, 4 Ω)
Signal to Noise Ratio S/N (A-weighted)
> 250
103 dB
audio limiters, thermal overload, peak current limiters, power-on delay
front to rear
Cooling
I
Safety Class
Dimensions (WxHxD), mm
Weight
103 dB
230 V / 50 Hz – 60 Hz
Power Requirements
Protection
-
483 x 88 x 405 mm, 19” / 2 HU
23.5 kg
16.5 kg
67
DPA 4000 Series
DPA 4000 Series
technical specifications
General
Load Impedance
Rated Output Power (Mains)
DPA 4410
DPA 4120
DPA 4140
100 Ω / 100 V, 50 Ω / 70 V
25 Ω / 50 V, 4 Ω / 20 V
DPA 4411
50 Ω / 100 V, 25 Ω / 70 V
12.5 Ω / 50 V, 4 Ω / 28 V
25 Ω / 100 V, 12.5 Ω / 70 V
6.25 Ω / 50 V, 4 Ω / 40 V
4 x 100 W
(acc. to IEC 268-3 / 19.4)
2 x 200 W configurable
1 x 200 W + 2 x 100 W configurable
200 W
(acc. to IEC 268-3 / 19.4)
400 W
(acc. to IEC 268-3 / 19.4)
balanced, floating
Power Output Characteristics
balanced
Input Characteristics
Input Sensitivity
775 mV / 0 dBu
Input Impedance
≥ 10 kΩ
≤1%
Distortion @ 1 kHz and Nom. Outp. Power
≤ 1.2 mV / -56 dBu
Interference Voltage (A)
60 Hz .. 20 kHz
Frequency Response
600 Ω
Load Impedance (monitor)
2 V / + 8.2 dBu
Nominal Output Voltage (monitor)
Output Characteristics (monitor)
unbalanced
electronically balanced
Class-AB, Transformer, Floating
Output Stage Topology
115 V / 230 V AC, ±10 % / 50 - 60 Hz or 24 V DC, -10 / +30 %
Power Requirements
Mains Power Consumption
1010 VA at nominal output
520 VA at nominal output
1020 VA at nominal output
377 VA driven at -10 dB
200 VA driven at -10 dB
380 VA driven at -10 dB
30 VA no signal
44 VA no signal
18 A at nominal output
9.1 A at nominal output
17.3 A at nominal output
7.5 A driven at -10 dB
3.7 A driven at -10 dB
7.1 A driven at -10 dB
0.4 A no signal / 2.5 mA in
stand-by
0.6 A no signal / 2.5 mA in
stand-by
62 VA no signal
24 V DC Power Consumption
1.0 A no signal / 2.5 mA in
stand-by
67 VA no signal
1.1 A no signal / 2.5 mA in
stand-by
High Temperature, Inrush Current Limiters, Short Circuit
Protection
Front-to-Rear, temperature controlled
Cooling
+5° C ... +40° C (40° F... 105° F)
Ambient Temperature Limits
I
Safety Class
483 x 132 x 345 mm, 19” / 3 HU
Dimensions (WxHxD), mm
340 mm
Installation Depth without Connectors
max. 410 mm
Installation Depth including Connectors
Weight
22.3 kg
22.5 kg
Optional
13.2 kg
16.7 kg
anthracite
Color
Extension-kits for the DPA 4410 / DPA 4411:
NRS 90206 Pilot Tone Monitoring (for four amplifiers)
NRS 90207 Ground-Fault Monitoring (for four amplifiers)
NRS 90227 Output Transformer (floating, balanced monitor
outputs) for DPA 4411
Additional Version DPA 4411:
DPA 4411N: DPA 4411 + NRS 90206 + NRS 90207
Extension-kits for the DPA 4120 / DPA 4140:
NRS 90222 Remote module (note: not supplied with the DPA
4120/DPA 4140)
NRS 90224 Pilot tone & ground-fault monitoring (note: not
supplied with the DPA 4120/DPA 4140)
NRS 90225 Standard input module (note: not supplied with the
DPA 4120/DPA 4140)
NRS 90227 Output transformer (floating, balanced monitor
output)
Additional Version DPA 4140:
DPA 4140N: DPA 4140 + NRS 90222 + NRS 90224
68
DPA 4000 Series
DPA 4411
General
Load Impedance
Rated Output Power
Maximum Output Power
Output Power in Bridged-Operation
DPA 4245
DPA 4260
28.5 Ω / 100V
20 Ω / 100V
14 Ω / 70 V
9.8 Ω / 70 V
1.8 Ω / 25 V
1.25 Ω / 25 V
4 Ω / 37.4 V
4 Ω / 44.7 V
350 W (acc. to IEC 268-3 / 19.4)
500 W (acc. to IEC 268-3 / 19.4)
450 W into 4 Ω
600 W into 4 Ω
700 W (acc. to IEC 268-3)
1000 W (acc. to IEC 268-3)
balanced, floating
Power Output Characteristics:
electronically balanced
Input Characteristics:
775 mV / 0 dBu
Input Sensitivity
Input Impedance
20 kΩ
Distortion @ 1kHz and Nom. Outp. Power
≤ 0.1 %
Frequency Response
45 Hz .. 22 kHz (-3 dB)
Signal to Noise Ratio
> 100 dB
Class-AB, Transformer, Floating
Output Stage Topology
230 V AC / 50 - 60 Hz
Power Requirements Mains
Mains Power Consumption
Protection
Cooling
1714 VA at nominal output
2268 VA at nominal output
635 VA driven at -10 dB
842 VA driven at -10 dB
78 VA no signal
131 VA no signal
audio limiter, thermal overload, DC, HF, Back-EMF, peak current limiter, initial
current inrush limiter, power-on delay,
saturation limitation for output transformers
Front-to-Rear, temperature controlled
+5° C ... +40° C (40° F... 105° F)
Ambient Temperature Limits
I
Safety Class
Dimensions (WxHxD), mm
483 x 132.5 x 384 mm, 19” / 3 HU
377 mm
Installation Depth without Connectors
max. 437 mm
Installation Depth including Connectors
Weight
Color
Optional
20.5 kg
22.5 kg
anthracite
Extension-kits for the DPA 4245 / DPA 4260:
NRS 90208 Input transformer (for one input)
69
DPA 8000 Series
DPA 8000 Series
technical specifications
General
Load Impedance
DPA 8150
50 V / 5 Ω
50 V
70 V
30.2 dB
33.1 dB
THD at rated output power MBW=80kHz, 1kHz
< 0.5 %
IMD-SMPTE, 60Hz, 7kHz
< 2.0 %
DIM 30, 3,15kHz, 15kHz
Max. Input Level
< 0.2 %
< -80 dB
Frequency Response, ref. 1 kHz, rated load
50 Hz...20kHz
Input Impedance, active balanced
20 k Ω
Signal to Noise Ratio, A-weighted
> 102 dB
Power Requirements
Power Consumption, at rated Output Power
Monitor
- rated Output Voltage
- rated Load Impedance
CAN
Control Port
Protection
Cooling
Ambient Temperature Limits
Safety Class
Dimensions (WxHxD), mm
Weight
70
36.2 dB
6.15 V (18 dBu)
Crosstalk, ref. 1 kHz at rated output power
Output Stage Topology
100 V
1.55 V (6 dBu)
Input Sensitivity, rated power @ rated load, 1kHz
Voltage Gain ref. 1kHz
100 V / 20 Ω
500 W
Rated Output Power, 1kHz, THD < 0.5%
Rated RMS Voltage Swing, 1kHz, THD=1%
70 V / 9.8 Ω
Class-D, Transformer, Floating
115 V / 230 V AC (-10% / +6%), 50-60 Hz or 24 V DC (-10% / +30%)
990 W (Mains) / 900 W (Battery)
1.3 V (4.5 dBu)
600 Ω
10...500 kBit/s, 2 x RJ-45
1 x 8-pole Euro Block, 3 Control Inputs/Outputs
2 Reference Outputs (15 V, 100 mA/GND), 1 Ready/Fault Output
Audio Limiters, High Temperature, DC, Short Circuit, Mains Over / Undervoltage Protection,
DC Supply Undervoltage Protection, Inrush Current Limiter, Ground Fault
Front-to-Rear, temperature controlled fans
-5 °C .. +45 °C
Class I
483 x 88 x 376 mm, 19” / 2 HE
16 kg
DPA 8000 Series
DPA 8412
General
Load Impedance
DPA 8225
50 V / 10 Ω
70 V / 19.6 Ω
50 V
50 V / 20 Ω
70 V
100 V
50 V
30.2 dB
33.1 dB
36.2 dB
< 2.0 %
DIM 30, 3,15kHz, 15kHz
< 0.2 %
30.2 dB
36.2 dB
< 1.0 %
< 0.1 %
Crosstalk, ref. 1 kHz at rated output power
< -80 dB
Frequency Response, ref. 1 kHz, rated load
50 Hz...20kHz
Input Impedance, active balanced
20 k Ω
Signal to Noise Ratio, A-weighted
> 102 dB
Class-D, Transformer, Floating
Output Stage Topology
115 V / 230 V AC (-10% / +6%), 50-60 Hz or 24 V DC (-10% / +30%)
990 W (Mains) / 900 W (Battery)
Power Consumption, at rated Output Power
Monitor
- rated Output Voltage
- rated Load Impedance
1.3 V (4.5 dBu)
600 Ω
10...500 kBit/s, 2 x RJ-45
CAN
1 x 8-pole Euro Block, 3 Control Inputs/Outputs
2 Reference Outputs (15 V, 100 mA/GND), 1 Ready/Fault Output
Audio Limiters, High Temperature, DC, Short Circuit, Mains Over / Undervoltage Protection,
DC Supply Undervoltage Protection, Inrush Current Limiter, Ground Fault
Front-to-Rear, temperature controlled fans
Cooling
-5 °C .. +45 °C
Ambient Temperature Limits
Class I
Safety Class
483 x 88 x 376 mm, 19” / 2 HE
Dimensions (WxHxD), mm
Weight
33.1 dB
6.15 V (18 dBu)
Max. Input Level
Protection
100 V
< 0.5 %
IMD-SMPTE, 60Hz, 7kHz
Control Port
70 V
1.55 V (6 dBu)
THD at rated output power MBW=80kHz, 1kHz
Power Requirements
100 V / 80 Ω
125 W
Input Sensitivity, rated power @ rated load, 1kHz
Voltage Gain ref. 1kHz
70 V / 39,2 Ω
250 W
Rated Output Power, 1kHz, THD < 0.5%
Rated RMS Voltage Swing, 1kHz, THD=1%
DPA 8412
100 V / 40 Ω
16 kg
18 kg
71
Americas
EMEA
Asia & Pacific Rim
Headquarters Americas
Bosch Security Systems, Inc.
12000 Portland Ave South
Burnsville, MN 55337, USA
USA— Phone: 1-800-392-3497
Fax: 1-800-955-6831
Canada— Phone: 1-866-505-5551
Fax: 1-866-336-8467
Latin America— Phone:
1-952-887-5532
Fax: 1-952-736-4212
Headquarters Europe,
Africa & Middle -East
Bosch Sicherheitssysteme GmbH
Robert-Koch-Strasse 100
D-85521 Ottobrunn, Germany
Headquarters Asia
Singapore: Telex Pte. Ltd.
3015A Ubi Road 1
05-10 Kampong Ubi Industrial Estate
Singapore 408705
Phone: +65 6746-8760
Fax: +65 6746-1206
Contact & Visitor Address
EVI Audio GmbH
Hirschberger Ring 45
D-94315 Straubing, Germany
Phone: +49 9421 706-0
Fax: +49 9421 706-265
France
EVI Audio France S.A.
Parc de Courcerin
Allée Lech Walesa
F 77185 Lognes, France
Phone: +33 1-6480-0090
Fax: +33 1-6006-5103
Japan
EVI Audio Japan Ltd.
5-3-8 Funabashi, Setagaya-Ku
Tokyo, Japan 156-0055
Phone: +81 3-5316-5020
Fax: +81 3-5316-5031
Hong Kong
Telex EVI Audio (HK) Ltd.
Unit 5,1/F, Topsail Plaza
11 On Shum Street
Shek Mun,Shatin HK
Phone: +852 2351-3628
Fax: +852 2351-3329
China
Telex EVI Audio (Shanghai) Ltd.
Room 2210-2215, Tower B
Far East International Plaza
No. 317, Xianxia Road Shanghai, China
PC: 200051
Phone: +86 21-6235-1677
© Bosch Sicherheitssysteme GmbH · Art.Nr. D164669 · Printed in Germany (F&W/DR) · 12000/01/09 · Subject to change without prior notice!
www.dynacord.com
Download PDF