Barco | ImagePro-HD | Installation manual | Barco ImagePro-HD Installation manual

ImagePRO, ImagePRO-SDI, ImagePRO-HD
Installation Manual
Model IP-2003
Barco Events USA
11101 Trade Center Drive
Rancho Cordova , CA 95670
Folsom
www.barco.com
www.folsom.com
Manual# 26-0302000-00 / Rev E
RECORD OF CHANGES
REV #
A
DATE
11/14/03
ECO #
1171
B
12/15/03
1188
Updated Save system State description to
include saving input channel (s/w rev 1.01).
Miscellaneous spelling corrections.
Added Ethernet functionality.
Added Save messages when exiting input,
output and system menus.
Released SDI/HD functionality (s/w rev 1.02).
A. Yerocostas
C
4/1/04
1255
Added Serial Commands.
Added Logo operation
Ching Ho
D
9/04
1318
Moved In Auto Acquire to the top menu
Added Hsync & Vsync adjustments to the
output timing adjustments menu.
Added Remote commands for Hsync & Vsync
adjustments.
Added Remote command for loading logo.
Added Remote command for edge
adjustments in oversample mode.
Updated limits on various remote commands.
A. Yerocostas
E
3/05
1406
Added EDID submenu to System menus
Updated Input timing adjustment serial
commands
A. Yerocostas
DESCRIPTION
Approved By
A. Yerocostas
Released
Manual # 26-0302000-00/Rev E
Operators Safety Summary
The general safety information in this summary is for operating personnel.
Do Not Remove Covers or Panels
There are no user-serviceable parts within the unit. Removal of the top
cover will expose dangerous voltages. To avoid personal injury, do not
remove the top cover. Do not operate the unit without the cover installed.
Power Source
This product is intended to operate from a power source that will not
apply more than 230 volts rms between the supply conductors or
between both supply conductor and ground. A protective ground
connection by way of grounding conductor in the power cord is essential
for safe operation.
Grounding the Product
This product is grounded through the grounding conductor of the power
cord. To avoid electrical shock, plug the power cord into a properly wired
receptacle before connecting to the product input or output terminals.
A protective-ground connection by way of the grounding conductor in the
power cord is essential for safe operation.
Use the Proper Power Cord
Use only the power cord and connector specified for your product. Use
only a power cord that is in good condition. Refer cord and connector
changes to qualified service personnel.
Use the Proper Fuse
To avoid fire hazard, use only the fuse having identical type, voltage
rating, and current rating characteristics. Refer fuse replacement to
qualified service personnel.
Do Not Operate in Explosive Atmospheres
To avoid explosion, do not operate this product in an explosive
atmosphere.
Terms In This Manual and Equipment Marking
VORSICHT
WARNING
NOTE
Highlights an operating procedure, practice,
condition, statement, etc., which, if not strictly
observed, could result in injury to or death of
personnel.
Highlights an essential operating procedure,
condition or statement.
CAUTION
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
AVERTISSEMENT!
Le point d´exclamation dans un triangle equilatéral signale
à alerter l´utilisateur qu´il y a des instructions d´operation
et d´entretien tres importantes dans la litérature qui
accompagne l´appareil
ein Ausrufungszeichen innerhalb eines gleichwinkeligen
Dreiecks dient dazu,
den Benutzer auf wichtige Bedienungs-und
Wartungsanweisungen in der Dem
Great beiliegenden Literatur aufmerksam zu machen.
ImagePRO™ Quick Start Guide
Step 1: Connect Input Sources to ImagePRO™
1.
2.
3.
Connect analog video source to the ImagePRO™ using the three universal video inputs.
Connect any SDI video source to the SDI video input (ImagePRO-SDI™ and ImagePRO-HD™ only).
Connect DVI video source to the DVI video input (ImagePRO-HD™ only).
Step 2: Connect ImagePRO™ to Output Devices
1.
2.
3.
4.
Connect Hi-res video output devices to the ImagePRO™ using the 5 BNC or HD-15 output connectors.
Connect NTSC or PAL monitor using the Composite or S-Video Output connectors
Connect SDI video devices to the SDI video output (ImagePRO-SDI™ and ImagePRO-HD™ only).
Connect DVI Digital Flat panel display to the DVI video output (ImagePRO-HD™ only).
Step 3: Power Up
Connect ImagePRO™ to AC power using the power cord supplied with the unit. Locate the power switch on the power entry module
at the rear of the unit and turn the power on. When initialization is complete, the front panel display will indicate that the unit has
powered up successfully. The Status screen is displayed when the initialization process is complete.
Step 4: Select and Save the desired Output Format
Press the SETUP button and then using the ADJUST knob, scroll down to “Output” and press the SEL key to enter the Output Setup
menu. Press SEL key to select the Output Format field and then use the ADJUST knob to locate the desired output format. Press
the SEL key again to select this output format. Now scroll down to Save Config and press the SEL key to save this format as the
default.
Press the ESC key to leave the Output Setup menu.
Step 5: Configure Input Sources
ImagePRO™ will automatically lock to video applied to the inputs and will make a attempt to match the Video format in the following
search order: Last configuration saved for the selected input channel, One of 64 stored configurations, any custom formats stored by the
user, library formats and finally using a “best guess” algorithm matching to the closest library format. While this approach generally leads
to an acceptable output image, it is strongly recommended that the user sets up a configuration file to precisely define the video
parameters associated with each input. The use of configuration files provides consistent, repeatable operation and allows the user to
adjust video parameters for each source to optimize image quality. Each time a source is selected with the Source Selection keys, the
configuration file associated with that source is automatically reloaded.
Setting up input configuration files is simple. Proceed as follows for each input.
1.
Select the source you wish to work by pressing the INPUT select key.
2.
Enter the INPUT SETUP menu by pressing the SETUP button and then pressing SEL to select the “Input” menu.
Examine the image on the display device and adjust the input parameters as desired. The Input Setup menu is
described in detail in chapter 3 of the ImagePRO™ manual. Many of the parameters may require no adjustment,
however, be sure that the “Input Format” and “Input Type” menu items are selected to match the incoming source video.
3.
When the input setup parameters have been set as desired, scroll down to “Save Config” using the ADJUST knob and
press the SEL button to save the current setup. The setup information is automatically assigned to the source used for
the input setup process. The input configuration file will automatically be recalled for use each time the source is
selected.
NOTE: Whenever a modification is made to a configuration, you must resave the changes following the procedure above.
This is a quick reference guide. For detailed information on the ImagePRO™, please refer to the
Installation and Operating Manual supplied with your unit.
Folsom Research, Inc. • 11101-A Trade Center Drive, Rancho Cordova CA 95670 • (916) 859-2500 • www.folsom.com
Table of Contents
IMAGEPRO™ QUICK START GUIDE ____________________________________________________________________I
TABLE OF CONTENTS _________________________________________________________________________________I
CHAPTER ONE _______________________________________________________________________________________ 1
IMAGEPROTM OVERVIEW ____________________________________________________________________________ 3
DESCRIPTION __________________________________________________________________________________________
IMAGEPRO™ FEATURES _________________________________________________________________________________
ADDITIONAL IMAGEPRO-SDI™ FEATURES __________________________________________________________________
ADDITIONAL IMAGEPRO-HD™ FEATURES ___________________________________________________________________
3
3
4
4
CHAPTER TWO ______________________________________________________________________________________ 5
INSTALLATION ______________________________________________________________________________________ 7
IMAGEPRO™ REAR PANEL CONNECTORS ___________________________________________________________________ 7
IMAGEPRO-SDI™ REAR PANEL CONNECTORS _______________________________________________________________ 8
IMAGEPRO-HD™ REAR PANEL CONNECTORS ________________________________________________________________ 9
RACK-MOUNT INSTALLATION ____________________________________________________________________________ 10
VIDEO INPUT CONNECTIONS _____________________________________________________________________________ 11
VIDEO OUTPUT CONNECTIONS ____________________________________________________________________________ 12
DVI-I VIDEO IN AND LOOP-THROUGH CONNECTORS (UNIVERSAL INPUT 1-IMAGEPRO-HD™)_________________________ 14
RS-232 REMOTE CONTROL CONNECTIONS __________________________________________________________________ 15
CONNECTION TO AC POWER _____________________________________________________________________________ 16
POWER CORD/LINE VOLTAGE SELECTION ____________________________________________________________________ 16
CHAPTER THREE ___________________________________________________________________________________ 19
OPERATION ________________________________________________________________________________________ 21
IMAGEPRO™ FRONT PANEL CONTROLS ____________________________________________________________________
IMAGEPRO-SDI™ FRONT PANEL CONTROLS ________________________________________________________________
IMAGEPRO-HD™ FRONT PANEL CONTROLS ________________________________________________________________
POWER UP INITIALIZATION ______________________________________________________________________________
STATUS DISPLAY _______________________________________________________________________________________
MENU CONTROL _______________________________________________________________________________________
MENU OPERATION _____________________________________________________________________________________
SETUP _______________________________________________________________________________________________
INPUT SETUP SUBMENU _________________________________________________________________________________
TYPE SELECTION _______________________________________________________________________________________
YPBPR COLORSPACE SELECTION ___________________________________________________________________________
SAMPLING ____________________________________________________________________________________________
TIMING ADJUST SUBMENU _______________________________________________________________________________
OVERSAMPLED TIMING EDGE SELECTIONS ____________________________________________________________________
1:1 SAMPLING OVERVIEW ________________________________________________________________________________
1:1 SAMPLING OPERATION ________________________________________________________________________________
AUTO CONFIG _________________________________________________________________________________________
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
21
22
23
24
26
26
28
28
28
29
29
30
30
30
31
31
31
i
SAMPLE PHASE _________________________________________________________________________________________
ACTIVE AREA__________________________________________________________________________________________
CONTRAST AND BRIGHTNESS ______________________________________________________________________________
COLOR BALANCE SUBMENU ______________________________________________________________________________
GAMMA ______________________________________________________________________________________________
ASPECT RATIO SUBMENU ________________________________________________________________________________
LETTERBOX SELECTION __________________________________________________________________________________
PROCESSING SUBMENU __________________________________________________________________________________
DE-INTERLACING ______________________________________________________________________________________
VIDEO PROCESSING DELAY ______________________________________________________________________________
VIDEO PROCESSING DELAY FOR IMAGEPRO __________________________________________________________________
VIDEO PROCESSING DELAY FOR IMAGEPRO-SDI AND IMAGEPRO-HD______________________________________________
SAVE CONFIG __________________________________________________________________________________________
RESET CONFIG _________________________________________________________________________________________
RECALL CONFIG ________________________________________________________________________________________
DELETE CONFIG ________________________________________________________________________________________
OUTPUT SETUP SUBMENU ________________________________________________________________________________
[OUTPUT FORMAT] _____________________________________________________________________________________
TIMING ADJUST SUBMENU _______________________________________________________________________________
COMP/S-VID ADJUSTMENTS SUBMENU _____________________________________________________________________
SYNC SETTINGS SUBMENU _______________________________________________________________________________
UNDERSCAN ___________________________________________________________________________________________
COLORSPACE __________________________________________________________________________________________
GAMMA ______________________________________________________________________________________________
SHARPNESS ___________________________________________________________________________________________
FLICKER REDUCE _______________________________________________________________________________________
GENLOCK SUBMENU ____________________________________________________________________________________
SOURCE ______________________________________________________________________________________________
GENLOCK TYPE SUBMENU ________________________________________________________________________________
H PHASE _____________________________________________________________________________________________
SC PHASE ____________________________________________________________________________________________
SAVE CONFIG __________________________________________________________________________________________
RESET CONFIG _________________________________________________________________________________________
IN AUTO ACQUIRE ______________________________________________________________________________________
FORMATS SUBMENU ____________________________________________________________________________________
SAVE AS SUBMENU _____________________________________________________________________________________
DELETE SUBMENU _____________________________________________________________________________________
H,V Parameters ________________________________________________________________________________________
V Rate _______________________________________________________________________________________________
Computed_H_Rate _____________________________________________________________________________________
Interlaced_____________________________________________________________________________________________
VIEWS SUBMENU _______________________________________________________________________________________
RECALL VIEWS SUBMENU _______________________________________________________________________________
SAVE VIEWS SUBMENU __________________________________________________________________________________
DELETE VIEWS SUBMENU ________________________________________________________________________________
EFFECTS SUBMENU _____________________________________________________________________________________
TECH SUPPORT SUBMENU _______________________________________________________________________________
SYSTEM SUBMENU _____________________________________________________________________________________
VFD BRIGHTNESS ______________________________________________________________________________________
RS232 SUBMENU_______________________________________________________________________________________
ETHERNET SUBMENU ___________________________________________________________________________________
SET STATIC IP SUBMENU ________________________________________________________________________________
EDID DVI INPUT FORMAT SUBMENU ______________________________________________________________________
PROGRAM EDID _______________________________________________________________________________________
SAVE SYSTEM STATE ____________________________________________________________________________________
FACTORY RESET ________________________________________________________________________________________
TEST PATTERN MENU ___________________________________________________________________________________
ZOOM MENU __________________________________________________________________________________________
PAN MENU ___________________________________________________________________________________________
PAN AND ZOOM RESET ___________________________________________________________________________________
ii
ImagePRO – Multi Format Image Processor
31
31
32
32
32
32
33
33
34
34
34
34
34
35
36
36
37
37
37
38
39
39
39
39
39
40
40
40
40
41
41
41
41
41
43
43
45
46
46
46
46
47
47
47
47
49
50
51
51
51
52
52
54
54
56
56
57
58
58
58
Manual # 26-0302000-00 / Revision E
CHAPTER FOUR_____________________________________________________________________________________ 61
SERIAL COMMAND SYNTAX _________________________________________________________________________ 63
SERIAL PARAMETERS ___________________________________________________________________________________ 63
RS232 MODE _________________________________________________________________________________________ 63
IMAGEPROTM REMOTE COMMANDS _________________________________________________________________ 64
IMAGEPROTM COMMAND LIST/DESCRIPTION ________________________________________________________ 68
CHAPTER FIVE _____________________________________________________________________________________ 95
SOFTWARE UPGRADE INSTRUCTIONS _______________________________________________________________ 97
OVERVIEW ___________________________________________________________________________________________
HARDWARE REQUIREMENTS _____________________________________________________________________________
SOFTWARE REQUIREMENTS ______________________________________________________________________________
CONNECTING TO FOLSOM RESEARCH ______________________________________________________________________
DOWNLOADING NECESSARY FILES ________________________________________________________________________
INSTALLING IMAGEPRO’S SOFTWARE FILES AND FLASH FILE LOADER ___________________________________________
STARTING THE IMAGEPRO FLASH FILE LOADER UTILITY ________________________________________________________
PREPARING TO UPGRADE THE IMAGEPRO UNIT ________________________________________________________________
UPLOADING FILES TO THE IMAGEPRO UNIT __________________________________________________________________
97
97
97
97
97
97
97
98
98
CHAPTER SIX _______________________________________________________________________________________ 99
BARCO FOLSOM INFORMATION ____________________________________________________________________ 101
BARCO FOLSOM WARRANTY ____________________________________________________________________________ 101
RETURN MATERIAL AUTHORIZATION (RMA) ______________________________________________________________ 101
BARCO FOLSOM CONTACT INFORMATION__________________________________________________________________ 101
APPENDIX _________________________________________________________________________________________ 103
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
iii
iv
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
1
CHAPTER ONE
Introduction
What you will find in this chapter…
‰
About ImagePROTM
‰
Features
Model IP-2003
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
1
2
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
ImagePROTM Overview
Description
The Folsom ImagePRO™ is a powerful all-in-one signal processor that accepts a wide range of video input signals
and processes them into a number of different output signal formats to meet the video requirements of virtually any
application. The ImagePRO™ line allows you to scale visual sources, mix and match them in any way while still
maintaining a high quality picture.
The unit is a high performance digital video scaler, scan converter, standards converter, switcher and transcoder in
one. The ImagePRO™ line is the ideal solution for converting RGB, HDTV, component, S-video, composite (NTSC,
PAL and SECAM), SDI, DVI, and HDSDI into a user-selectable format. ImagePRO™ output formats include a wide
variety that support popular computer video, standard video, plasma, DVI, and HDTV rates.
The ImagePRO™ has an advanced feature set that includes:
universal inputs, aspect ratio conversion, memory presets, test patterns, Genlock, picture adjustments, motion
adaptive de-interlacing, and 3:2 and 2:2 pull-down detection.
ImagePRO™ Features
•
Three universal inputs accept RGBHV/RGBCs/RGsB computer video, component video (STD or HDTV), SVideo, or composite video with loop-through
•
Input Video detection and Auto-acquisition. ImagePRO will auto detect and match input video to stored
formats or user configurations.
•
Four video outputs; (2) RGB or component video, (1) composite video, and (1) S-video
•
Aspect ratio conversion and adjustments
•
Pan and zoom
•
Freeze
•
10-Bit processing
•
De-interlacing modes: Motion Adaptive and Field to Frame
•
3:2 pulldown detection for NTSC and 2:2 film detection for PAL video sources
•
Decodes NTSC, PAL, and SECAM
•
Ethernet connector for real-time control
•
Encodes NTSC and PAL
•
Vertical lock (Genlock) eliminates image tears and other artifacts in scaled motion video by eliminating frame
rate conversion
•
Executive mode: protects system configuration settings during use
•
64 independent input configuration memory presets
•
Backed by three-year warranty
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
3
Additional ImagePRO-SDI™ Features
•
One SD SDI input and output
•
Can be later upgraded to ImagePRO-HD
•
Motion adaptive de-interlacing for HDTV inputs
•
Low Video Delay
•
Logo image capture and recall feature
•
Dissolve to/from stored logo
Additional ImagePRO-HD™ Features
4
•
SD SDI/HD SDI input and output
•
DVI-I connectors support both universal analog and DVI input with loop-through
•
DVI output
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
2
CHAPTER TWO
INSTALLATION
What you will find in this chapter…
‰
Rear Panel Connectors
‰
Rack-Mount Installation
‰
Video Input & Output Connections
‰
Remote Control Connections
‰
Power Cord/Line Voltage Selection
Model IP-2003
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
5
6
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Installation
ImagePRO™ Rear Panel Connectors
UNIVERSAL INPUT 1
R/R-Y/C
G/Y/COMPOSITE
IN
UNIVERSAL INPUT 3
B/B-Y
IN
H/C
COMPOSITE
OUTPUT
V
IN
IN
OUTPUT 2
H/C
V
GENLOCK IN
H/C/BURST
IN
LOOP
IN
REMOTE CONTROL
LOOP
LOOP
IN
UNIVERSAL INPUT 2
R/R-Y/C
LOOP
G/Y/COMPOSITE
LOOP
LOOP
B/B-Y
UNIVERSAL INPUT 3
H/C
LOOP
V
S-VIDEO
OUTPUT
R/R-Y
G/Y/COMPOSITE
B/B-Y
V
ETHERNET
OUTPUT 1
RS-232
Figure 2-1: ImagePRO™ Rear Panel
Video Input BNC connectors with loop-through (Universal Input 3)
Video Input HD-15 connectors with loop-through (Universal Inputs 1 & 2)
Video Output BNC connectors (Output 2)
Video Output HD-15 connectors (Output 1)
S-video on 4-pin mini-DIN connector
Composite Output BNC
Genlock BNCs
Remote Control RJ-45 Ethernet Connector
Remote Control RS-232 DB-9 Connector
AC Power connector
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
7
ImagePRO-SDI™ Rear Panel Connectors
UNIVERSAL INPUT 1
G/Y/COMPOSITE
R/R-Y/C
IN
UNIVERSAL INPUT 3
B/B-Y
SDI INPUT
SDI OUTPUT
V
H/C
IN
IN
COMPOSITE
OUTPUT
OUTPUT 2
H/C
V
GENLOCK IN
H/C/BURST
IN
IN
LOOP
IN
REMOTE CONTROL
LOOP
LOOP
IN
UNIVERSAL INPUT 2
R/R-Y/C
LOOP
G/Y/COMPOSITE
LOOP
B/B-Y
UNIVERSAL INPUT 3
LOOP
LOOP
H/C
V
S-VIDEO
OUTPUT
R/R-Y
G/Y/COMPOSITE
B/B-Y
V
ETHERNET
OUTPUT 1
RS-232
Figure 2-2: ImagePRO-SDI™ Rear Panel
Video Input BNC connectors with loop-through (Universal input 3)
Video Input HD-15 connectors with loop-through (Universal inputs 1 & 2)
Standard Definition SDI Digital Video Input BNC
Video Output BNC connectors (Output 2)
Video Output HD-15 connectors (Output 1)
S-video on 4-pin mini-DIN connector
Composite Output BNC
Genlock BNCs
Standard Definition SDI Digital Video Output BNC
Remote Control RJ-45 Ethernet Connector
Remote Control RS-232 DB-9 Connector
AC Power connector
8
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
ImagePRO-HD™ Rear Panel Connectors
UNIVERSAL INPUT 1
R/R-Y/C
G/Y/COMPOSITE
IN
UNIVERSAL INPUT 3
B/B-Y
SDI INPUT
SDI OUTPUT
V
H/C
IN
IN
IN
COMPOSITE
OUTPUT
OUTPUT 2
H/C
V
GENLOCK IN
H/C/BURST
DVI-D OUTPUT
IN
LOOP
IN
REMOTE CONTROL
LOOP
LOOP
IN
UNIVERSAL INPUT 2
R/R-Y/C
LOOP
G/Y/COMPOSITE
LOOP
B/B-Y
UNIVERSAL INPUT 3
LOOP
H/C
LOOP
V
S-VIDEO
OUTPUT
R/R-Y
OUTPUT 1
G/Y/COMPOSITE
B/B-Y
V
ETHERNET
RS-232
Figure 2-3: ImagePRO-HD™ Rear Panel
Video Input BNC connectors with loop-through (Universal input 3)
Video Input HD-15 connectors with loop-through (Universal input 2)
Digital / Analog Video Input on DVI-I Connector with loop-through (Universal input 1)
Standard Definition/High Definition SDI Digital Video Input BNC
Video Output BNC connectors (Output 2)
Video Output HD-15 connectors (Output 1)
DVI Digital Video Output on DVI-D Connector
S-video on 4-pin mini-DIN connector
Composite Output BNC
Genlock BNCs
Standard Definition/High Definition SDI Digital Video Output BNC
Remote Control RJ-45 Ethernet Connector
Remote Control RS-232 DB-9 Connector
AC Power connector
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
9
Rack-Mount Installation
ImagePROTM units are designed to be rack mounted and are supplied with front rack-mount hardware. Rear rackmount brackets are available as a kit and are recommended for use when units are mounted in transit cases. When
rack mounting the unit, remember that the maximum ambient operating temperature for the unit is 40 degrees C.
Leave at least one inch of space front and rear to make sure that the airflow through the fan and vent holes is not
restricted. When installing equipment into a rack, distribute the units evenly to prevent hazardous conditions that may
be created by uneven weight distribution. Connect the unit only to a properly rated supply circuit. Reliable grounding
(earthing) of rack-mounted equipment should be maintained.
10
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Video Input Connections
Universal Input Connectors
The video input section on the ImagePROTM rear panel provides three universal inputs. Each input can accept RGB,
YUV, S-Video (Y/C), or composite (NTSC, PAL or SECAM) video signals. On ImagePRO™ and ImagePRO-SDI™
Universal Inputs 1 & 2 are provided with HD-15 female connectors. On ImagePRO-HD™ Universal input 2 is provided
with an HD-15 connector. Universal input 1 is provided with a DVI-I connector, which can be converted to an HD-15
via the DVI-I to HD-15 adaptor provided with the unit. Universal Input 3 is provided with BNC connectors on all
models. All inputs are provided with a corresponding buffered loop-through. Connection pins for each video signal are
specified below.
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
Pin 15
RGBHV
RED
GREEN
BLUE
RED return
GREEN return
BLUE return
GND
Hsync or Csync
Vsync
5
1
15
11
6
HD-15 Input Connector Pinout
(as viewed from rear of unit)
Format – RGB
(Typical Devices: Computers)
R
G
B
H
V
Source to ImagePROTM
R/R-Y/C
G/Y/COMPOSITE
B/B-Y
H/C
V
Format – S-Video (Y/C)
(Typical Devices: S-Video DVD or VCR)
Y
C
Source to ImagePROTM
G/Y/COMPOSITE
B/B-Y
Format – YUV or Y Pr Pb (Betacam)
(Typical Devices: DVD Player or Betacam Deck)
Y
Pr
Pb
Y
U
V
Source to ImagePROTM
G/Y/COMPOSITE
R/R-Y
B/B-Y
or
G/Y/COMPOSITE
R/R-Y
B/B-Y
Format – Composite (Typical Devices: NTSC/PAL DVD or VCR)
Source to ImagePROTM
NTSC/PAL/SECAM
G/Y/COMPOSITE
*NOTE: Composite sync or separate Hsync and Vsync signals are accepted. Sync on Green is also supported.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
11
Video Output Connections
Four independently buffered outputs (one five wire BNC connection, one HD-15, one S-Video, and one Composite
video BNC) are provided. Both 5-wire and HD-15 outputs provide the same Video in RGB or YPbPr format. Outputs
are available depending on the resolution selected. For example, RGB video at 1024x768@60Hz will be available
both on the 5-wire BNC and HD-15 outputs. Likewise, NTSC Video will be available on the Composite, S-Video and
SDI output connectors.
The operator can select the type of output sync to match application requirements. Separate C (Composite) or
separate H/V (Horizontal/Vertical) as well as sync on Green Video sync modes are supported.
HD-15 Output Connector Pinout
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
Pin 15
RGB Output
RED
GREEN
BLUE
RED return
GREEN return
BLUE return
GND
Hsync or Csync
Vsync
5
1
15
11
6
HD-15 Output Connector Pinout
(as viewed from rear of unit)
Format – RGB
(Typical Devices: Monitor/Plasma/Projector)
R
G
B
H
V
Sourced from ImagePROTM
R/R-Y/C
G/Y/COMPOSITE
B/B-Y
H/C
V
Format – S-Video (Y/C)
(Typical Devices: S-Video VCR,Monitor)
Y
C
Sourced from ImagePROTM
G/Y/COMPOSITE
B/B-Y
Format – YUV or Y Pr Pb (Betacam)
(Typical Devices: Betacam Deck)
Y
Pr
Pb
Y
U
V
Sourced from ImagePROTM
G/Y/COMPOSITE
R/R-Y
B/B-Y
or
G/Y/COMPOSITE
R/R-Y
B/B-Y
Format – Composite (Typical Devices: NTSC/PAL VCR,Monitor)
Sourced from ImagePROTM
NTSC/PAL/SECAM
G/Y/COMPOSITE
*NOTE: Composite sync or separate Hsync and Vsync signals as well as Sync on Green are supported.
12
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
RGB/YPbPr Video Output
Connect the output device to the set of BNC connectors marked R/R-Y, G/Y and B/B-Y on the output section of the
ImagePRO™ rear panel
S-Video (Y/C) Video Output
The Y/C video output connector is a 4-Pin Mini DIN located on the rear panel of the ImagePRO™. Using a
commercial S-VHS cable, connect the Y/C video output to the input of the S-VHS device (monitor, video recorder,
etc.).
Composite Video Output
Connect the composite input of the monitor to the composite output BNC of the ImagePRO™ using a 75-ohm coaxial
cable.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
13
DVI-I Video In and Loop-Through Connectors (Universal Input 1-ImagePro-HD™)
Two DVI-I female connectors are located on the rear panel of the ImagePRO-HD™. One is used for Video input and
the other one is used for the buffered DVI-I Loop-Through. This Connector can be used with Analog inputs using the
DVI-I to HD-15 adaptor provided with ImagePRO-HD™.
Pin
Function
Pin
Function
1
T.M.D.S. Data2-
13
T.M.D.S. Data3+
2
T.M.D.S. Data2+
14
+5V Power
3
T.M.D.S. Data2/4 Shield
15
ground (for +5V)
4
T.M.D.S. Data4-
16
Hot Plug Detect
5
T.M.D.S. Data4+
17
T.M.D.S. Data0-
6
DDC Clock
18
T.M.D.S. Data0+
7
DDC Data
19
T.M.D.S. Data0/5 Shield
8
Analog Vertical Sync
20
T.M.D.S. Data5-
9
T.M.D.S. Data1-
21
T.M.D.S. Data5+
10
T.M.D.S. Data1+
22
T.M.D.S. Clock Shield
T.M.D.S Data1/3 Shield 23
T.M.D.S. Clock+
11
12
T.M.D.S. Data3-
24
T.M.D.S. Clock-
MicroCross Pins
Pin
Function
C1
Analog Red Video
C2
Analog Green Video
C3
Analog Blue Video
C4
Analog Horizontal Sync
C5
Analog Common Ground Return
Legend
DDC = Display Data Channel
T.M.D.S. = Transition Minimized Differential Signal
14
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
RS-232 Remote Control Connections
The Remote serial port can be connected to a PC or other Remote Controller to support remote control of the
TM
ImagePRO unit. Pinouts for the remote port are shown below.
1
2
6
3
7
4
8
5
9
DB-9
RS-232 Signal
Description
1
CD
Carrier Detect
2
RXD
Received Data
3
TXD
Transmitted Data
4
DTR
Data Terminal Ready
5
GND
Signal Ground
6
DSR
Data Set Ready
7
RTS
Request To Send
8
CTS
Clear To Send
9
RI
Unused
Refer to Section 3, SYSTEM: RS-232 Menu, for configuring the hardware handshake.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
15
Connection to AC Power
Power Cord/Line Voltage Selection
ImagePROTM is rated to operate with the following supplies:
Input Power:
100-240 VAC, 47-63 Hz
Power Consumption :
150 watts maximum
TM
The ImagePRO Wide Screen Image Processor performs line voltage selection automatically. No user controls are
required for line voltage selection.
WARNING
TM
When the ImagePRO is used with 230-volt supplies, a UL listed line cord rated for
250 volts at 15 amps must be used. This cord will be fitted with a tandem prong-type
plug.
Tandem Plug
TM
La choix de la ligne de voltage se realize automatiquement par I’ImagePRO
Transformateur Graphique On n’apas besoin du controller usager pour la choix de la ligne
de voltage.
AVERTISSEMENT
TM
Das ImagePRO -Gerät mu beim Anschlu an 240V ~ mit einer vom VDE auf
250V/10A geprüften Netzleitung mit einem Schukostecker ausgestattet sein.
AVERTISSEMENT
16
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Connect ImagePROTM to 115 VAC power using the power cord supplied with the unit. Locate the power switch on the
power entry module at the rear of the unit and turn the power on. While the main board is initializing, “please wait” will
be displayed and the front panel keys will be turned on and off. When initialization is complete, the Setup Menu will
be displayed.
VORSICHT
ein Ausrufungszeichen innerhalb eines gleichwinkeligen
Dreiecks dient dazu,
den Benutzer auf wichtige Bedienungs-und
Wartungsanweisungen in der Dem
Great beiliegenden Literatur aufmerksam zu machen.
WARNING
The rear panel ON/OFF switch does not
disconnect the unit from input AC power. To facilitate disconnection of
AC power, the power cord must be connected to an accessible outlet
near the unit. Building Branch Circuit Protection: For 115 V use 20 A,
for 230 V use 8 A.
WARNING
When the ImagePRO™ is used in the 230-volt mode, a UL
listed line cord rated for 250 volts at 15 amps must be used
and must conform to IEC-227 and IEC-245 standards. This
cord will be fitted with a tandem prong-type plug.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
17
18
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
3
CHAPTER THREE
Operation
What you will find in this chapter…
‰
Front Panel Controls
‰
Status Display
‰
Menu Control
‰
Setup Menus
‰
Input Setup Menu
‰
Output Setup Menu
‰
System Options Menu
‰
Test Pattern Menu
‰
Zoom Menu
‰
Pan Menu
Model IP-2003
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
19
20
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Operation
ImagePRO™ can be controlled by using the front panel menu controls or remotely via RS-232 or Ethernet interface.
The front panel menu controls are described in detail in this section. Remote control commands are described in
detail in section 4.
ImagePRO™ Front Panel Controls
MENU KEYS
R E S E A
SEL
R C H
SETUP
INPUTS
TEST
PAT
1
ESC
PAN
2
3
BLACK
FREEZE
ZOOM
ADJUST
Figure 3-1 ImagePRO™ Front Panel
SEL
Used to select a menu option, control setting, or configuration change.
ESC
Current operation in progress is cancelled. Control returns to the previous menu or the system status display. Any
changes made within a control function are undone.
SETUP, TEST PAT, ZOOM, PAN
These four buttons allow entry into the menu system. Pressing any of these four buttons causes that button to light
up, and the display goes to the top-level of that particular menu system. Pressing the button again darkens the
button and changes the display to the Status Display mode. Pressing a different menu button will cause the system
to immediately switch to the new menu. The test pattern light also acts as an indicator that a test pattern is on.
1, 2, 3
The input source buttons are used to select the input, which will be routed to the output using the transition type
specified in the Effects menu.
BLACK
The Black button can be thought of as an additional input video source. When selected the Black button LED will be
lit and the output will be black. The Black input can be de-selected by selecting one of the other three input sources.
When Black Input is selected the Status Display indicates “INTERNAL BLACK” as the input format and the Pan and
Zoom buttons are not operational.
FREEZE
Turns the Freeze feature on or off. When turned on the Led will be illuminated. Allows a displayed image to be
temporarily frozen. When Freeze is selected the Pan and Zoom buttons are not operational and the Input Setup and
View menus are inaccessible since these adjustments cannot be applied to a frozen image. If another input is
selected Freeze will be turned off.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
21
ImagePRO-SDI™ Front Panel Controls
MENU KEYS
R E S E A
SEL
R C H
SETUP
INPUTS
TEST
PAT
1
ESC
PAN
2
3
SDI
LOGO
---------BLACK
FREEZE
ZOOM
ADJUST
Figure 3-2 ImagePRO-SDI™ Front Panel
SEL
Used to select a menu option, control setting, or configuration change.
ESC
Current operation in progress is cancelled. Control returns to the previous menu or the system status display. Any
changes made within a control function are undone.
SETUP, TEST PAT, ZOOM, PAN
These four buttons allow entry into the menu system. Pressing any of these four buttons causes that button to light
up, and the display goes to the top-level of that particular menu system. Pressing the button again darkens the
button and changes the display to the Status Display mode. Pressing a different menu button will cause the system
to immediately switch to the new menu. The test pattern light also acts as an indicator that a test pattern in on.
1, 2, 3, SDI
The input source buttons are used to select the input, which will be routed to the output using the transition type
specified in the Effects menu.
LOGO / BLACK
The Logo/Black button can be thought of as an additional input video source and allows the operator to capture and
display a stored image. When selected the Logo/Black button LED will be lit and the output will display either a
stored image (typically a company logo) or black.
To capture an image, the operator presses and holds the input source button to select the desired input source and
then presses the Logo/Black button. ImagePRO-SDI™ will freeze the output image and capture an output frame from
the selected input source and store the image in non-volatile memory. A progress bar and related messages will be
shown on the VFD display during this capture process to notify the operator that the image is being captured and
saved.
The Logo/Black input can be de-selected by selecting one of the other four input sources. When Logo/Black Input is
selected and no logo is stored, the output will display black and the Status Display indicates “INTERNAL BLACK” as
the input format and the Pan and Zoom buttons are not operational. When Logo/Black Input is selected and there is a
logo stored, the output will display the logo and the Status Display indicates “LOGO” as the input format and the Pan
and Zoom buttons are not operational.
Once an image has been stored, the operator can use the LOGO/BLACK key to select the stored image. If an image
has not been stored, the default image is a black frame.
FREEZE
Turns the Freeze feature on or off. When turned on the LED will be illuminated. Allows a displayed image to be
temporarily frozen. When Freeze is selected the Pan and Zoom buttons are not operational and the Input Setup and
View menus are inaccessible since these adjustments cannot be applied to a frozen image. If another input is
selected Freeze will be turned off.
22
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
ImagePRO-HD™ Front Panel Controls
MENU KEYS
R E S E A
SEL
R C H
SETUP
INPUTS
TEST
PAT
1
ESC
PAN
2
3
SDI
LOGO
---------BLACK
FREEZE
ZOOM
ADJUST
Figure 3-3 ImagePRO-HD™ Front Panel
SEL
Used to select a menu option, control setting, or configuration change.
ESC
Current operation in progress is cancelled. Control returns to the previous menu or the system status display. Any
changes made within a control function are undone.
SETUP, TEST PAT, ZOOM, PAN
These four buttons allow entry into the menu system. Pressing any of these four buttons causes that button to light
up, and the display goes to the top-level of that particular menu system. Pressing the button again darkens the
button and changes the display to the Status Display mode. Pressing a different menu button will cause the system
to immediately switch to the new menu. The test pattern light also acts as an indicator that a test pattern is on.
1, 2, 3, SDI
The input source buttons are used to select the input, which will be routed to the output using the transition type
specified in the Effects menu.
LOGO / BLACK
The Logo/Black button can be thought of as an additional input video source and allows the operator to capture and
display a stored image. When selected the Logo/Black button LED will be lit and the output will display either a stored
image (typically a company logo) or black.
To capture an image, the operator presses and holds the input source button to select the desired input source and
then presses the Logo/Black button. ImagePRO-HD™ will freeze the output image and capture an output frame from
the selected input source and store the image in non-volatile memory. A progress bar and related messages will be
shown on the VFD display during this capture process to notify the operator that the image is being captured and
saved.
The Logo/Black input can be de-selected by selecting one of the other four input sources. When Logo/Black Input is
selected and no logo is stored, the output will display black and the Status Display indicates “INTERNAL BLACK” as
the input format and the Pan and Zoom buttons are not operational. When Logo/Black Input is selected and there is a
logo stored, the output will display the logo and the Status Display indicates “LOGO” as the input format and the Pan
and Zoom buttons are not operational.
Once an image has been stored, the operator can use the LOGO/BLACK key to select the stored image. If an image
has not been stored, the default image is a black frame.
FREEZE
Turns the Freeze feature on or off. When turned on the LED will be illuminated. Allows a displayed image to be
temporarily frozen. When Freeze is selected the Pan and Zoom buttons are not operational and the Input Setup and
View menus are inaccessible since these adjustments cannot be applied to a frozen image. If another input is
selected Freeze will be turned off.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
23
In addition to the twelve illuminated push buttons, the Front Panel controls also include a Vacuum Fluorescent
Display (VFD) and an adjustment knob.
The operation of each menu displayed on the VFD is described in detail in the following sections of this document.
Power Up Initialization
Locate the power switch on the rear panel and turn the ImagePROTM ON. While ImagePROTM is initializing, the
following messages will be displayed on the VFD display:
Program Loading
Please wait
Transferring to
main program
ImagePRO
Folsom Research
Version 2.00
Initializing...
The third line of the menu above displays the version of the software that is currently being executed. The software
version number will change as software upgrades are released.
If an Ethernet mode is saved, it will be set at this time. If DHCP is On, ImagePRO will attempt to contact the DHCP
server for an IP address. During this process, the following message will be displayed on the VFD display (it takes
approximately 40 seconds to connect):
Searching for
DHCP server
Please wait…
If DHCP is off and a static IP address was saved (i.e. IP address set to anything other than 000.000.000.000),
ImagePRO will attempt to set the Ethernet port with the IP address selected. During this process, the following
message will be displayed on the VFD display (it takes approximately 40 seconds to connect):
24
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Setting Ethernet
with static IP addr
Please wait…
For ImagePRO-SDI and ImagePRO-HD units, when there is a logo image stored in non-volatile memory, the logo will
be loaded into memory at this time. During this loading process, the following message will be displayed on the VFD
display:
Loading Logo
Please wait
A progress bar will be displayed on the third line of the VFD display indicating the progress of loading the logo image.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
25
Status Display
IN:
OUT:
<type>
<in_format>
<genl_mode+src>
<out_format>
After power-up or anytime none of the four menu buttons are selected, the display will show a basic status. This
screen gives information about the currently selected system inputs and outputs. The input section always reflects the
currently selected input channel, as determined by the input buttons. If the input channel is changed, then the input
fields of this screen may change. Most other changes will be caused by menu selections and will therefore become
visible when returning to this display. In this display, the variable fields are as follows:
<type>
Specifies the type of input signal being processed, and is one of NTSC/PAL/SECAM, SDI, HD-SDI, RGB, YPbPr, or
DVI.
<in_format>
Indicates the current input video format in the form, Hact x Vact @ Vr Hz (i.e 1280x1024@60 Hz). If a user input
configuration is used for the current input video, the <in_format> field will show the name of the user input
configuration instead. If the currently selected input channel and source do not have a valid input signal, the
<in_format> field will display “Invalid Signal”.
<genl_mode+src>
Indicates the current genlock mode and source (if locked.) The possible entries for this field are:
Freerun
(Not locked. Freerun timing)
HVScLock, Brst (Genlocked to an external Black Burst signal)
HVScLock, InVid (Genlocked to input video)
HV Lock, Csync (Horizontal and Vertical lock to external Composite Sync)
HV Lock, H+V In (Horizontal and Vertical lock to external separate H and V signals)
HV Lock, InVid
(Horizontal and Vertical lock to input video)
V Lock, Brst
(Vertical lock to external Blacl Burst signal)
V Lock, V In
(Vertical lock to external V sync)
V Lock, InVid
(Vertical lock to input video)
If the unit is set for a particular genlock mode and source, but that source is missing or lock can not be achieved, then
the unit will automatically revert to freerun mode, the display will change to “No Lock”, and the source field will remain
unchanged.
<out_format>
Indicates the current output video format in the form, Hact x Vact @ Vr Hz (i.e 1920x1080i@59.94 Hz).
Menu Control
The adjustment knob and the SEL and ESC keys are used to navigate through a series of menus displayed on the
VFD display. The menus are used to enter setup parameters. Pressing one of the four hot keys will call up the
corresponding menu on the VFD.
26
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
The user can scroll through the menu items by turning the ADJUST control knob. A pointer (>) at the left of a menu
item indicates the current position of the scroll bar. When the desired menu item is reached, the user presses the
SEL key to select that menu item. The sub-menu pointer (>>) at the right of a menu item indicates that a sub-menu
will be displayed if that menu item is selected. The pointer at the left hand side of the display changes to a pound sign
(#) indicating that a parameter is selected. After a parameter has been selected, the user can modify the associated
parameter values by turning the ADJUST control knob. The operator can accept the changes with SEL or press ESC
to exit the current menu item without modifying current settings.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
27
Menu Operation
Setup
This is the top-level menu accessed by pressing the SETUP button. Setup information can be stored in non-volatile
memory within ImagePROTM and will be automatically recalled each time the unit is turned on. The contents of this
menu are:
SETUP
> Input
Output
In Auto Acquire
Formats
Views
Effects
Tech Support
System
Factory Reset
>>
>>
On
>>
>>
>>
>>
>>
>>
Input Setup Submenu
This menu sets all the configuration options for the selected input channel. The Input Setup Menu is illustrated
below. This menu can be accessed from the SETUP MENU. Changing the menu entries of one input channel will not
affect the configuration of the other channels.
NOTE:
Configuration parameters entered in this menu are saved in non-volatile memory for each input source using
the SAVE CONFIG menu item. If the SAVE CONFIG menu item is not selected, the information will not be
restored upon the next system power up sequence. If the user performed changes and did not save them the
following message will be displayed upon exiting the Input menu by pressing ESC, SETUP, PAN, TEST PAT
and ZOOM.
Save Input Cfg?
<SEL> = Yes
<ESC> = No
The user may select Yes to save the changes or No to continue operation without saving the changes. If the
user exits the Input setup menu by selecting another input any changes made will not be saved in nonvolatile memory.
28
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
INPUT
<in_format>
> Type
ColorSpace
Sampling
Timing Adjust
Contrast
Brightness
Color Balance
Gamma
Aspect Ratio
Letterbox
Processing
Save Config
Reset Config
Recall Config
Delete Config
<type>
[val]
[val]
>>
<val>
<val>
>>
<val>
>>
<val>
>>
>>
>>
>>
<in_format>
Indicates the current input video format in the form, Hact x Vact @ Vr Hz (i.e 1024x768@75 Hz). If the currently
selected input channel and source do not have a valid input signal, the <in_format> field will display “Invalid Signal”.
When In Auto Acquire is on the input video format will be detected in the following search order: last used
configuration for the selected input channel, any saved input configurations, custom library formats
created by the user, standard library formats or best guessed to the closest video format in library. If the
video format is best guessed it will be displayed enclosed within asterisks in the Status Display. (i.e
*1024x768@60.11*). If the video format is recalled from a saved input configuration, a ‘c’ character is
displayed as the right most character. (i.e. 1024x768@59.94
c).
When Auto Acquire is off the ImagePRO™ will attempt to lock to the signal with the input video format
selected by the user. If the currently selected format does not match the input signal for the selected
channel the display will remain black and the Status Display will indicate “Invalid Signal”.
Type selection
Values for this item are: RGB, YPbPr, NTSC/PAL/SECAM, SDI, and DVI.
The type selection allows the user to select among the possible signal types available at the current input channel.
When Auto Acquire is on the type selections will be limited depending on the signal on the currently selected input
channel. For example, if channel 1 of an ImagePRO-HD™ is connected to a DVI source, DVI will be the only choice
and it could not be changed. Also SDI will be the only choice whenever the SDI input is selected on ImagePRO-SDI™
and ImagePRO-HD™.
When Auto Acquire is off the type selections are expanded to allow the user to manually select the Video type.
If a source type is chosen and a correct signal cannot be detected for that source, the <in_format> field in the INPUT
SETUP menu, and in the status display, will indicate Invalid Signal.
YPbPr Colorspace selection
Values for this item are: RGB, SMPTE, BETA, M-II.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
29
The Color space value allows the user to select among the possible Component Video Standards for YPbPr. For all
other video types the color space is RGB and cannot be selected or changed. The default selection for YPbPr is
SMPTE. The user may change this setting to BETA or M-II to allow the ImagePRO™ to correctly sample the Y, Pb
and Pr components across their full dynamic range.
Sampling
Values for this item are: OverSample and 1:1. 1:1 is the default setting.
The Oversample option is only available for RGB and YPbPr analog inputs. All other input types have defined sample
clocks that are inherently 1:1. If the input is set to one of the other types, the value for this selection will be n/a.
Timing Adjust Submenu
This menu allows for exact positioning of the input signal's active area.
There are two forms for this menu, depending on the current sampling mode. For oversampling, the menu is:
OVRSMP TIMING ADJUST
> Right Edge
<val>
Left Edge
<val>
Top Edge
<val>
Bottom Edge
<val>
When the sample mode is 1:1, the menu is:
1:1 TIMING ADJUST
> Auto Config
Sample Phase
<val>
H Total
<val>
H Position
<val>
H Active
<val>
V Total
<val>
V Position
<val>
V Active
<val>
Oversampled Timing Edge selections
These four menu items are available only when the Sample Mode is Oversample. They are used to define the exact
locations of the active video edges. For the right and left edges, these values set the edge locations, in pixels, relative
to the start of H Sync. For top and bottom, the values are in lines, relative to the start of V Sync.
NOTE: It is recommended that the user turns on the Output Raster Box on ImagePRO™ when making active
area adjustments. The input image should be adjusted to align with all four edges of the raster box. The
raster box is intentionally “broken” to allow the user to view the input video behind it and align the input
video to the raster box precisely.
30
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
1:1 Sampling Overview
In order to scale an image it must first be digitized. This is the process of changing the analog graphics signals (Red,
TM
Green, and Blue for example) into pixels stored in the ImagePRO image memory. The default mode of the
TM
ImagePRO is to over sample the input image producing more samples than there are in the original source
material. The over sampled image is then scaled to the final output resolution.
An approach called 1:1 Sampling produces a superior image by sampling the analog video signal at exactly the same
rate as that of the original source. This allows the image to be re-constructed with reduced digitizing artifacts. This
1:1 Sampling approach requires very accurate settings and even a small sampling error causes noise on the output
image. Both the sample clock frequency and phase must be correct to obtain a properly sampled image.
ImagePROTM incorporates automatic adjustments in the 1:1 Sampling mode.
1:1 Sampling Operation
NOTE:
To automatically set-up for 1:1 Pixel Sampling the input image must have non-black data with 50% gray or
brighter pixels around all four edges of the active area.
The standard Windows GUI is a good example. With an appropriate image displayed on the output Monitor, scroll to
the Auto Config menu item and press Select. In a couple of seconds, the image should return properly adjusted.
The sample clock phase can be further fine tuned by adjusting it. The functions of the menu items that are unique to
1:1 sampling operation are described below.
Auto Config
This menu item is only available when Sample Mode is 1:1 and the input is analog RGB or YPbPr. Pressing SEL to
execute this command causes the system to go through a 1:1 active area acquisition process.
NOTE:
In order for Auto Config to function correctly, the input source for the currently selected channel must have
50% gray or brighter pixels around all four edges of the active area.
Sample Phase
The adjustment range is -16 to 15. Zero is the default setting for Sample Phase.
This selection is only available when Sample Mode is 1:1 and the input is analog RGB or YPbPr. The value is initially
filled in by the Auto Config command, or set to the default. The user can then further fine-tune the image by adjusting
the sample clock phase directly.
Active Area
These menu items are only available when Sample Mode is 1:1 and the input is analog RGB or YPbPr. The values
are initially filled in by the Auto Config command, or set to defaults. The user can then adjust the active area definition
directly.
For the Horizontal entries, the unit of measure is pixels. H Total indicates the total pixel count per line. H Position sets
the offset of start of active area from H sync. H Active sets the size of the active area. H Total cannot be adjusted if
input type is DVI / SDI.
For the vertical entries, the unit of measure is lines. V Total indicates the total line count per frame. V Position sets
the offset of start of active area from V sync. V Active sets the size of the active area.
NOTE: It is recommended that the user turns on the Output Raster Box on ImagePRO™ when making active
area adjustments. The input image should be adjusted to align with all four edges of the raster box. The
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
31
raster box is intentionally “broken” to allow the user to view the input video behind it and align the input
video to the raster box precisely.
Contrast And Brightness
The adjustment range is 75.0% to 125.0%. 100% is the default setting for both contrast and brightness.
The Contrast and Brightness controls allow the operator to adjust the overall contrast and brightness of the image.
Color Balance Submenu
The menu entries depend on the current input type. For RGB input, the menu is:
COLOR BALANCE
> Red Contrast
Red Bright
Grn Contrast
Grn Bright
Blue Contrast
Blue Bright
Reset All
<val>
<val>
<val>
<val>
<val>
<val>
The adjustment range is -25.0% to +25.0%. 0.0% is the default setting for both contrast and brightness.
Each of the contrast and brightness settings operates in conjunction with the global contrast and brightness settings,
above.
For Composite, S-video, YpbPr, or SDI input, the menu is:
COLOR BALANCE
> Hue
Saturation
Reset All
<val>
<val>
The Hue value is measured in degrees, and the range is -180 to +180. Hue is n/a for YPbPr inputs.
The saturation value is in percentage, and for composite and S-Video inputs ranges from 0% to 150%, with 100%
being the nominal value. For YPbPr and SDI inputs, the range is 75.0% to 125.0%.
The Reset All item is a command that sets all values back to their defaults.
Gamma
This selection allows the user to specify the Gamma associated with the current input. The value range is 1.0 to 3.0,
in steps of 0.1. Default gamma values are stored with each video format.
Aspect Ratio Submenu
32
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
This menu allows the user to set the input signal aspect ratio. The menu is:
INPUT ASPECT RATIO
> Mode
<val>
Ratio
<val>
The Mode value is selected among the following choices: 1:1, 3:2, 4:3, 5:4, 16:9, Custom
The ImagePRO will select and display the input video aspect ratio according to the input format detected. For
example, computer video at 1280x1024@60Hz will default to 5:4 aspect ratio, NTSC video will default to 4:3 aspect
ratio, and HDTV1080i video will default to 16:9 aspect ratio.
The Ratio line is only visible when the selected mode is Custom. It is a decimal number ranging from 0.750 to 3.000.
The default value is dependent on the last Mode aspect ratio value before Custom is selected.
Letterbox selection
The value selections are: Off, On.
When Off is selected, the image will be allowed to fill the entire output raster. If On is selected, the top and bottom of
the output raster are cropped to a 16:9 Aspect Ratio. This feature is especially useful when used with Wide-Screen
DVD sources. It allows the user to process this type of source without seeing the Black Bars at the top and bottom of
the image.
Processing Submenu
PROCESSING
> Sync Sel
DeIntlc
Pulldown Comp
Sync Slice (mV)
[val]
[val]
[val]
[val]
The Sync Sel menu item applies only to analog RGB inputs. The digital input sources have embedded syncs, and the
composite, S-video, and YPbPr inputs always will take the sync from the Y (or composite) channel. For these inputs,
the value field will indicate n/a. The sync choices are Auto, H/V, CSync, and SOG. In Auto mode, the system will find
the sync in any of the three possible sources. If one of the sources is explicitly chosen, the system uses only that
input as a sync source, unless it finds there is no sync input at that source. In which case it will act as if it is in Auto
mode.
The Sync Slice menu item selects the sync comparator threshold for RGsB (RGB with Sync on Green) or YPbPr
analog component video sources. The value can range from 20mV to 280mV and is adjustable in steps of 10mV. The
default value is 160mV. When ImagePRO detects Macrovision copy protection on the incoming YPbPr NTSC/PAL
video, the Sync Slice value is automatically repositioned to 60mV to account for the reduced amplitude sync pulse.
NOTE: The default Sync Slice level has been optimized for virtually all sources that will be encountered and
should rarely, if ever, require adjustment. However, the ability to adjust the Sync Slice level is provided to
improve sync detection/synchronization in cases of extremely noisy RGsB or YPbPr video signals.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
33
De-interlacing
In order to process an interlaced video source, the ImagePRO circuits must first de-interlace the image. Deinterlacing is the process by which interlaced video (video where even lines are scanned during one field and odd
lines are scanned during the next field) are converted to progressive format (where lines in the frame are sequentially
scanned).
ImagePRO utilizes Motion Adaptive De-interlacing (MAD) techniques to de-interlace most video sources. An alternate
mode, Field to Frame (Fld->Frm), avoids motion artifacts by converting individual input fields to progressive output
frames. While vertical resolution will be reduced in this mode, a significant reduction in video processing delay is
achieved.
Video Processing Delay
In order to eliminate video processing delay associated with frame rate conversion, it is recommended that the
ImagePRO output be locked to the input source frame rate. Video delays provided below assume that the input and
output frame rates are locked.
Video Processing Delay for ImagePRO
ImagePRO utilizes a MAD processor capable of processing interlaced NTSC and PAL inputs. Interlaced inputs at
other rates (such as 1920 x 1080i) are processed in Field to Frame mode (Fld->Frm).
When the MAD de-interlacing mode is selected, maximum video processing delay is 4 input fields (5 fields if the
output is not frame locked to the input).
If Field to Frame mode (Fld->Frm) is selected, maximum video processing delay is 1 input field. (2 fields if the output
is not frame locked to the input).
Video Processing Delay for ImagePRO-SDI and ImagePRO-HD
ImagePRO-SDI and ImagePRO-HD utilize an advance MAD processor capable of processing interlaced inputs up to
HDTV (1920 x 1080i) rates.
When the MAD de-interlacing mode is selected, maximum video processing delay is 2 input fields (3 fields if output
not frame locked to input).
The Pulldown Detect menu item selects between On and Off. This menu item is applicable only for standard video
(component, s-video, composite) video inputs. The default mode is off. The 3:2 Sequence Detect feature should be
turned on to process video derived from film source material.
Save Config
SAVE CONFIG AS
> File1
Save Config
This menu item allows the user to save and name up to 64 input configurations that can be matched as part of the
ImagePRO auto acquisition process.
34
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
NOTE:
Configuration parameters entered in the input setup menu are saved in non-volatile memory for each input
source by using the SAVE CONFIG menu item. If the SAVE CONFIG menu item is not selected, the
information will not be restored upon the next system power up sequence.
A filename may include up to 19 characters. In order to change the filename, scroll to the filename field and press
SEL. The > sign will change to a # sign and the first character will be selected for editing. You may choose a
character by turning the encoder knob. To select a character press SEL. The next character will automatically be
selected for editing. When you are done entering the filename press SEL again. The filename will be truncated up to
the current character position. In order to save the input configuration under the filename selected scroll down to
Save Config and press SEL.
If the selected filename has never been used, the line “—Config Saved –“ will appear below the SAVE CONFIG menu
item as shown below.
SAVE CONFIG AS
> File1
Save Config
-- Config Saved --
If the selected filename has already been used, the following menu is displayed.
Overwrite File1
?
<SEL> = Yes
<ESC> = No
Pressing SEL will overwrite the saved file with the current configuration. Pressing ESC will display the Save Config
menu and allow you to change the filename.
If all 64 input configurations have been used the following menu is displayed.
SAVE CONFIG AS
LIBRARY FULL
<ESC> = Continue
You may press ESC and then select the Delete Config menu to delete some old configurations and allow room for
new configurations to be stored.
Reset Config
This command removes all user-entered configuration settings from the current input. This causes the system to
restore the format parameters from the library values for the current input format. If the current format was derived as
a “best guess” then those best guess values are restored.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
35
Recall Config
RECALL CONFIG
> File1
Recall Config
This menu allows the user to recall input configurations that were previously saved for the currently selected input
format and type. Only configurations that match the current format and type will be displayed. In order to recall a
configuration, press SEL. The > sign will change to #. Use the encoder knob to browse the file list. Press SEL to
choose the file you wish to recall. Scroll down to Recall Config and press SEL.
Delete Config
DELETE CONFIG
> File1
Delete Config
This menu allows the user to delete any input configurations that were previously saved. In order to delete a
configuration, press SEL. The > sign will change to #. Use the encoder knob to browse the file list. Press SEL to
choose the file you wish to delete. Scroll down to Delete Config and press SEL. The following submenu will be
displayed asking you to confirm your choice.
Delete File1
?
<SEL> = Yes
<ESC> = No
Ensure that the selected file is the one you wish to delete and press SEL, otherwise press ESC.
NOTE: If the deleted input configuration is currently used by any input channel, the system will restore the
format parameters to the default library values for those channels.
36
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Output Setup Submenu
This menu is used to configure the outputs of the ImagePRO. The Output Setup Menu is illustrated below. This menu
can be accessed from the SETUP MENU.
OUTPUT
[out_format]
> Timing Adjust
>>
Comp/S-Vid Adj
>>
Sync Settings
>>
Underscan
<val>
Colorspace
<val>
Gamma
<val>
Sharpness
<val>
Flicker Reduce
<val>
Genlock
>>
Save Config
Reset Config
NOTE:
Configuration parameters entered in this menu are saved in non-volatile memory by using the SAVE CONFIG
menu item. If the SAVE CONFIG menu item is not selected, the information will not be restored upon the next
system power up sequence. If the user performed changes and did not save them the following message will
be displayed upon exiting the Output menu by pressing ESC, SETUP, PAN, TEST PAT and ZOOM.
Save Output Cfg?
<SEL> = Yes
<ESC> = No
The user may select Yes to save the changes or No to continue operation without saving the changes. If the
user exits the Output setup menu by selecting another input any changes made will not be saved in nonvolatile memory.
[Output Format]
The user may select the desired Output format from a list of standard formats as well as custom format saved by the
user. Note that the unit’s outputs are not updated until the SEL button is pressed.
NOTE: The Digital Cinema Projector resolutions at 2048x1080p@59.94Hz and 2048x1080p@60Hz are only
supported on the ImagePRO-SDI and ImagePRO-HD.
Timing Adjust Submenu
The Timing Adjust sub-menu allows the user to make adjustments to the currently selected output format timing
parameters. This menu is illustrated below.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
37
TIMING ADJUST
> H Total
H Position
H Active
H Sync
V Total
V Position
V Active
V Sync
[val]
[val]
[val]
[val]
[val]
[val]
[val]
[val]
For the Horizontal entries, the unit of measure is pixels. H Total indicates the total pixel count per line. H Position sets
the offset of start of active area from H sync. H Active sets the size of the active area. H Sync sets the H sync width.
For the vertical entries, the unit of measure is lines. V Total indicates the total line count per frame. V Position sets
the offset of start of active area from V sync. V Active sets the size of the active area. V sync sets the V sync width.
When the output format is NTSC or PAL, H Total and V Total cannot be changed.
Comp/S-Vid Adjustments Submenu
NOTE:
This sub-menu is not available if the selected output format does not support Composite and S-Video
outputs.
This sub-menu allows adjustments specifically to the output encoder, which produces composite and S-Video outputs
as illustrated below:
COMP/S-VID ADJ
> Brightness
Contrast
Hue
Saturation
Pedestal
<val>
<val>
<val>
<val>
<val>
Brightness values correspond to a percentage of the output format’s standard brightness level. Adjusting this up or
down will cause the output encoder to shift the Y (luminance) value correspondingly. The range is 100% to 114%,
with 100% being nominal.
Contrast values correspond to a percentage of the output format’s standard contrast level. The range for this is
limited to 75.0% to 125.0%, with 100.0% being nominal. Steps are 0.1%.
Hue is n/a if the output format is PAL. For NTSC, the Hue is measured in degrees, and is adjustable from -22.0 to
+22.0 degrees. Steps are in 0.1 degree increments.
Saturation values are given as a percentage of the output format’s standard saturation level. The range for this is
limited to 75.0% to 125.0%, with 100.0% being nominal. Steps are 0.1%.
Pedestal is used to enable or disable the 7.5 IRE pedestal on NTSC output. Turn the knob to highlight On or Off and
press SEL. The default is On for NTSC. This control is not available for PAL. When PAL is selected, pedestal is
disabled.
38
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Sync Settings Submenu
This menu allows the user to specify the sync types for the current output. The submenu is illustrated below:
SYNC SETTINGS
> Sync Out
SOG/Y
Serrations
Equalization
[val]
[val]
[val]
[val]
The Sync Out menu item selects among the five possible output sync types:
CSync, +H+V, +H-V, -H+V, -H-V. The default setting is -H-V for most formats. For NTSC, PAL, RS-170 and RS-343
the default is Csync with equalizations on.
The SOG/Y item selects among: Off, Standard and Tri-Level for RGB color space. If the Output color space is YPbPr
the Off selection is not available since sync information is always part of the Y output.
The Serrations menu item sets serrations in the output composite sync pattern during V Sync time. Values are On or
Off. The default setting is On.
The Equalization menu item sets equalization pulses in the output composite sync pattern around V Sync time.
Values are On or Off. This menu is n/a if the output is not interlaced.
Underscan
Underscan reduces the output image area by the specified percentage. Range is 0% to 15%.
Colorspace
The Colorspace selection sets the output mode for analog component outputs. Choices are: RGB, YPbPr.
Gamma
This selection allows the user to specify the Gamma associated with the current output. The value range is 1.0 to
3.0, in steps of 0.1. Default gamma values are stored with each video format.
Sharpness
The Sharpness selection sets the scaler’s sharpening (or softening) amount. This setting has a default value of 0,
and sets the scaler to its optimum sharpness level. The sharpening range extends from -10 (most softening) to
+10(most sharpening).
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
39
Flicker Reduce
The Flicker Reduce value is n/a when the output format is non-interlaced. For interlaced formats, the range is Off
(no flicker reduction) or +1 (minimum flicker reduction) through +20 (maximum flicker reduction).
Genlock Submenu
This sub-menu sets up the genlock operation:
GENLOCK
> Source
Type
H Phase
SC Phase
[val]
>>
<val>
<val>
Source
Source selects the genlock source from among the following:
Freerun
Input Video (Genlock source is the currently selected input Video)
H+V Sync (Lock source are external H & V sync pulses)
Csync
(Lock source is an external Composite sync input)
Blk Burst (Genlock source is an external Black Burst Signal)
Genlock Type Submenu
This sub-menu allows the user to selects the different types of genlock:
GENLOCK TYPE
> Type
[val]
Type selects the genlock mode. The selections depend on the selected genlock source and possibly the input/output
configurations. If the source is Freerun, the type is n/a. The available types are:
V Lock
(Vertical lock only)
HV Lock
(Both Horizontal and Vertical lock)
HVSc Lock (Full genlock)
Type V is available for all genlock sources.
Type HV is available for all sources, but only if the input and output V Totals are the same.
Type HVSc is only available when the output format is PAL or NTSC. The source must be the Black Burst external
genlock source or Input Video. As in the HV type, the V total of the source must equal the V total of the output
format.
When Genlock type HVSc is selected, the message “FOR COMPOSITE OUT” is displayed as shown below:
40
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
GENLOCK TYPE
> Type
HVScLock
FOR COMPOSITE OUT
With ImagePRO-SDI or ImagePRO-HD units, when Genlock type HV is selected, and the ImagePRO output is
interlaced, the message “FOR SDI OUT” is displayed as shown below:
GENLOCK TYPE
> Type
FOR SDI OUT
HVScLock
H Phase
The H Phase setting allows the output H timing to be adjusted relative to the genlock source. This selection is n/a
when the genlock is V lock only. The range for H Phase is +/- one-half the H Total.
SC Phase
The SC Phase sets the output subcarrier phase, relative to the genlock source. This selection is only valid when the
source is Blk Burst, or input decoded video. In other cases, the value field indicates n/a. The range for this setting is
-180 to +180 degrees.
Save Config
This command saves all current output configuration settings. This save will persist across power cycles.
NOTE:
Configuration parameters entered in the output setup menu are saved in non-volatile memory by using the
SAVE CONFIG menu item. If the SAVE CONFIG menu item is not selected, the information will not be
restored upon the next system power up sequence.
Reset Config
This command removes all user-entered configuration settings and restores the default values for the current output
format. This command also clears the saved configuration (if any) so that the system will not restore the unwanted
configuration at power up.
In Auto Acquire
Values for this item are: On and Off. On is the default setting for Auto Acquire.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
41
When Input Auto Acquire is On, the system will always perform a full sync acquisition on the input signal anytime the
input channel is selected, the input type is changed, or the input signal changes sync rates.
When Auto Acquire is Off, the system will use the last known configuration for each input channel, to the greatest
extent possible. At some point, the input signal may be too far away from the saved configuration, in which case a
good input lock may not be possible. If the input signal is too different from the saved configuration to be usable, then
the <in_format> field in the Status Display will read “Invalid Signal”.
NOTE: It is recommended that In Auto Acquire is left on for most users. The ImagePRO™ will automatically
detect and acquire the input video type and resolution in most cases and limit menu selections as applicable
to the detected Video type. Advance users that know the input video timing parameters may choose to turn
In Auto Acquire off and select them manually. In Auto Acquire must be turned off in switching applications
where the user already configured and saved the unit’s input setup. Turning auto acquisition off will provide
the fastest transition times for switching applications. When auto-acquisition is on the transition time will be
greater due to the additional time required to analyze the input video timing.
42
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Formats Submenu
This menu is used to define and save a new video format, or to edit and save a previously-defined format.
These saved formats are stored in a user library, which is searched during the auto-acquisition process
before the standard system library. All saved formats are available as input formats on any input channel
and as output formats. A maximum of 32 custom formats may be stored.
FORMATS
>
[format_name]
Save As
>>
Delete
>>
H Total
[val]
H Active
[val]
H Front Porch
[val]
H Sync
[val]
H Rate (KHz)
[val]
V Total
[val]
V Active
[val]
V Front Porch
[val]
V Sync
[val]
V Rate (Hz)
[val]
Interlaced
[val]
NOTE:
Format parameters entered in the edit format menu are saved in non-volatile memory by using the Save As
menu item. If the Save As menu item is not selected, the information will not be restored upon the next
system power up sequence. If the user performed changes and did not save them the following message will
be displayed upon exiting the System menu by pressing ESC, SETUP, PAN, TEST PAT and ZOOM.
Save Custom Format?
<SEL> = Yes
<ESC> = No
The user may select Yes to save the changes or No to continue operation without saving the changes.
<format_name> Selection
This unlabeled menu selection allows the user to select the format to edit. The choices consist of the names of the
standard formats library (excluding TV standard formats) plus any previously-defined formats. The initial value is
720x480p.
Save As Submenu
This menu allows the user to save the current format settings to an existing or new name.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
43
SAVE FORMAT AS
> <editable_string>
Save
The <editable_string> field can be selected with the SEL button. The content of the field will initially be “Format1”.
Editing the string is initiated by pressing SEL with the > cursor on the editable line. At this point, the >
changes to #, and a cursor will appear at the first character position of the string. Turning the knob will change the
character at the cursor position. When the desired character is found, the SEL button may be pressed, and the cursor
will move to the next position. Successive characters are selected in this manner.
Rotating the knob past the end of the character set will wrap around to the other end. When the string is completed,
press the ESC key to leave the string editing function. At this point, the user may select the Save command to save
the format and continue.
If the selected filename has never been used, the line “— Format Saved –-“ will appear below the SAVE menu item
as shown below.
SAVE FORMAT AS
> <format_name>
Save
-- Format Saved --
If the format library is full, the following message will be displayed:
SAVE FORMAT AS
LIBRARY FULL
<ESC>=Continue
After pressing ESC, the user may scroll through the names already in the user library, and replace one of them.
If the user attempts to save a new format with a reserved name (one that is already used in the standard library), the
following message will be displayed:
Save Format As:
<editable_string>
Reserved Name
The user can now go back and re-edit the name.
44
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
If the user picks a name that's already in use in the user library, a confirmation menu is displayed when the user
invokes the Save command:
<format_name>
Overwrite Format?
<SEL> = Yes
<ESC> = No
Pressing the SEL key will cause the existing library format to be overwritten with the new format.
Pressing the ESC key will cancel the save operation and return to the previous menu.
Delete Submenu
This menu allows the user to delete any saved user formats from the user format library.
DELETE FORMAT
> <saved format name>
Delete
In order to delete a saved user format, press SEL. The > sign will change to #. Use the encoder knob to browse the
user format list. Press SEL to choose the format you wish to delete. Scroll down to DELETE menu item and press
SEL. The following confirmation screen appears:
<format_name>
Delete Format?
<SEL> = Yes
<ESC> = No
Pressing the SEL key will cause the currently selected library format to be deleted. Pressing the ESC key will cancel
the delete operation and return to the previous menu.
If the format selected for deletion is currently the Output format used or is the Output format that is saved in the
output configuration, the following screen will be displayed:
DELETE FORMAT FAIL
FORMAT IN USE/SAVED
IN OUT CHNL/CONFIG
<ESC> = Continue
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
45
If the format selected for deletion is currently an Input format used by any of the input channels or is the Input format
that is saved in an input configuration, the following screen will be displayed:
DELETE FORMAT FAIL
FORMAT IN USE/SAVED
IN INPUT CHNL/CFG
<ESC> = Continue
H,V Parameters
These selections set the H and V parameters (Total, Active, Front Porch, and Sync Width). The units are in pixels for
H and lines for V.
The possible range for any one is determined in part by the values of the others. Changing one value will not change
any other values, but it will limit the range available for other values. (Total = Front Porch + Sync Width + Back Porch
+ Active)
V Rate
This item sets the vertical sync rate of the format in Hz.
Computed_H_Rate
This line is updated to indicate the horizontal rate in KHz, computed from other parameters.
Interlaced
The value for this selection is either On or Off. When set to on, the V Total value will be forced to an odd number.
46
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Views Submenu
The Views menu allows management of up to 16 stored “Views”. A View is a combination of zoom and pan settings.
For example, the user may define a view that maps the entire input image to the upper left quarter of the output
image. A view is defined by actually creating the settings with the Pan and Zoom buttons. Once a view is created, it
may be saved (and named) in this menu. A stored view can later be recalled and applied to the currently selected
input channel.
VIEWS
> Recall
Save
Delete
>>
>>
>>
Recall Views Submenu
The Recall selection allows the user to choose a stored View, by name, and assign it to the currently selected input
channel. The value field is the list of stored view names plus Default. The default view displays the input image with
default pan (0%) and zoom (100%) settings.
RECALL VIEW
> View
Recall
[ViewX]
Save Views Submenu
This menu allows the user to save the current view setting to a named view. Press SEL and scroll through the list of
available Views (View1 … View15). Choose a name and press SEL. Scroll down to Save and press SEL.
SAVE VIEW
> View
Save
[ViewX]
As confirmation, when the operator selects Save to save the view, the line “— View Saved –-“ will appear below the
SAVE menu item as shown below.
SAVE VIEW
> View
[ViewX]
Save
-- View Saved --
Delete Views
Manual # 26-0302000-00 / Revision E
Submenu
ImagePRO – Multi Format Image Processor
47
The view to delete is selected from the list of available views. Deleting a view simply resets its pan and zoom
settings to their default values. A confirmation screen will appear when SEL is pressed.
DELETE VIEW
> View
Delete
48
ImagePRO – Multi Format Image Processor
[val]
Manual # 26-0302000-00 / Revision E
Effects Submenu
EFFECTS
> Trans With
Trans Time
[val]
[val]
The effects menu selects the transition effect when switching between input channels. The user may select form the
following selections:
- Transition with Image Cut; The currently selected channel will be frozen, the new channel’s video will be acquired
and cut to the Output display.
- Transition with Black; The currently selected channel will fade to Black and then the new channel’s video will
transition in. The transition time will depend on the Transition time selected (1.0-5.0 seconds).
Note: Transition times provided are for switching applications with auto-acquisition turned off. When autoacquisition is on the transition time will be greater due to the additional time required to analyze the input
video timing.
- Transition with Logo; (ImagePRO-SDI & ImagePRO-HD only). This mode is only selectable if there is stored Logo
image in non-volatile memory. The currently selected channel will dissolve to the stored Logo image and then the
new channel’s video will dissolve in from the Logo. The transition time will depend on the Transition time selected
(1.0-5.0 seconds).
Note: Transition times provided are for switching applications with auto-acquisition turned off. When autoacquisition is on the transition time will be greater due to the additional time required to analyze the input
video timing.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
49
Tech Support Submenu
TECH SUPPORT
Version
<fw_ver>
Phone
866-FRI-SUPT
The version displayed is the installed operating firmware version number.
50
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
System Submenu
This menu allows the user to adjust the VFD Brightness and remote control setting for RS-232 or Ethernet Interfaces
as illustrated below.
SYSTEM
> VFD Brightness <val>
RS232
>>
Ethernet
>>
EDID DVI In Frmt
>>
Save System State
NOTE:
Configuration parameters entered in the system menu are saved in non-volatile memory by using the SAVE
SYSTEM STATE menu item. If the SAVE SYSTEM STATE menu item is not selected, the information will not
be restored upon the next system power up sequence. If the user performed changes and did not save them
the following message will be displayed upon exiting the System menu by pressing ESC, SETUP, PAN, TEST
PAT and ZOOM.
Save System Cfg?
<SEL> = Yes
<ESC> = No
The user may select Yes to save the changes or No to continue operation without saving the changes.
VFD Brightness
The VFD Brightness menu selections control the intensity of the front panel vacuum fluorescent display (VFD). The
adjustment range is -7 to 8. -7 is the dimmest setting and 8 is the brightest. The factory default setting is 8.
NOTE:
Whenever possible it is recommend using a low intensity setting to avoid “burn-in” of the display.
RS232 Submenu
RS232
> Baud
Parameters
Handshake
Reset
[val]
[val]
[val]
The Baud value is selected from the following values: 1200, 2400, 9600, 19200, 38400.
The parameters value is selected from the following values: N81, E71, O71, E72, O72.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
51
The handshake value is selected from the following values: Off or On (CTS/RTS).
The reset command restores the RS232 settings to defaults: 38400, N81, Handshake On.
After connecting the PC COM port to the ImagePRO RS-232 connector the user may open a serial terminal session
(Hyper-terminal, Procomm etc) and configure it to match the ImagePRO serial port settings as they are configured in
this menu. At this point the ImagePRO command prompt (#) will be displayed at the terminal. The user may type
“Help” to see a list of remote commands supported. For a complete list of commands and descriptions please see
section 4.
Ethernet Submenu
ETHERNET
> DHCP
[val]
Set Static IP
>>
IP
xxx.xxx.xxx.xxx
M
xx:xx:xx:xx:xx:xx
DHCP can be set to Off or On. When DHCP is set as Off, the operator can manually enter a static IP address (with
valid Subnet mask and Gateway) for Ethernet communication to function. Consult the network administrator for valid
IP address, Subnet mask and Gateway.
When DHCP is on, the ImagePRO queries the DHCP server for a valid IP address. If the ImagePRO finds a DHCP
server and receives an IP address, the IP address is displayed. If a server is not found, then the unit does not get an
IP address allotted to it.
NOTE:
It takes several seconds for the unit to query the Ethernet port and obtain the IP address. During this time the
SEL key will remain lit.
The Set Static IP submenu selection is used to manually select a static IP address when a DHCP server is not
available. This submenu is only accessible if DHCP is set to Off.
The IP line is an informational line indicating the current IP address. If an IP address hasn't been established (no
DHCP server found, or the network cable is not connected), then the IP address will read "000.000.000.000".
The M line is an informational line showing the MAC (hardware) address of the unit’s Ethernet port.
Set Static IP Submenu
This menu invokes a special editor that allows the user to edit the IP address. This is only available when the DHCP
mode is off.
The menu starts out in the form:
52
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
SET IP
SUB
GW
IP
nnn.nnn.nnn.nnn
nnn.nnn.nnn.nnn
nnn.nnn.nnn.nnn
Valid "nnn" fields can range from 000 to 255. As with any selection line, the user must press the SEL button to begin
editing the IP values. At this point, the first value is highlighted. Turning the knob moves the value through the range
0 to 9. When the desired value is found, the user presses SEL. This moves the highlight to the next value, and the
process repeats. After every 3 digits, a ‘.’ will automatically be placed. The final SEL (at the last value) completes the
edit, turning off edit mode. Pressing ESC at any point before the final SEL press will abort the edits and leave the
address value unchanged. It is necessary to set the Subnet mask and Gateway address before setting the IP address
field. Only after setting the IP address will ImagePRO attempt to set the Ethernet port. An IP address of
000.000.000.000 indicates that the user is not interested in Ethernet communication and the Ethernet port will be
ignored.
NOTE:
It takes several seconds for the unit to communicate with the Ethernet port and set the IP address. During
this time the SEL key will remain lit.
When all the Ethernet setup is done, the operator can communicate with the ImagePRO via the Ethernet. Use the IP
address and port 10001. On a Microsoft Windows PC, open a command prompt window and type the following on the
prompt and press ENTER:
> telnet xxx.xxx.xxx.xxx 10001
Once Ethernet communication is established, the telnet window functions in a similar fashion to a serial COM port
communication. Consult the network administrator to make sure the ImagePRO can communicate with the PC.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
53
EDID DVI Input Format submenu
This menu allows the user to update the ImagePRO-HD™’s EDID’s preferred resolution.
NOTE: This menu is for advanced users only. Do not reprogram the EDID unless it is necessary. This menu
is only available on ImagePRO-HD™.
Extended Display Identification Data or EDID is a VESA standard data format that contains information about a
display device and its capabilities, including the preferred as well as the allowed resolutions of the device.
ImagePRO-HD™ EDID file is stored in a non-volatile memory. This file is read by a computer’s DVI graphic card
when the DVI output is connected to ImagePRO-HD™’s channel 1 DVI-I input connector during boot-up. ImagePRO
must be powered on first for the EDID information to be read.
EDID DVI IN FORMAT
<EDID_format>
Program EDID
<EDID_format>
The user may select the preferred DVI video format to program to ImagePRO-HD™’s EDID non-volatile memory
using this menu item.
Program EDID
Select this menu item to program the resolution defined on the <EDID_format> menu item as the preferred DVI
resolution.
NOTE: Make sure there are no cables connected to ImagePRO’s DVI-I input and loop through connectors. If
there is a DVI input connected to the ImagePRO-HD™ it will interfere with the programming operation causing
it to fail. If a Flat Panel monitor is connected on the loop through, it’s own EDID information will also be
changed. For these reasons ImagePRO will display the following message before attempting to program the
new EDID information in non-volatile memory.
WARNING! MAKE SURE
DVI IN & LOOP THRU
ARE NOT CONNECTED
SEL=Cont, ESC=Abort
Press the SEL key to proceed with the non-volatile memory programming. Press the ESC key to abort this operation.
As an additional precaution the ImagePRO will verify that indeed no cables are connected to the DVI-I input and loop
through connectors. If a DVI source or Display device are detected the following message will be displayed.
54
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
ERROR! DVI INPUT AND
LOOP THRU CONNS MUST
BE DISCONNECTED!
<ESC> = Continue
Press the ESC key to proceed with the non-volatile memory programming. Once no DVI source or display Device are
detected, ImagePRO will proceed with programming the non-volatile memory while the following message is briefly
displayed.
Programming EDID
Please wait . . . .
If the non-volatile memory programming is successful, the following message will be displayed:
EDID Prog Done
Connect DVI input
and reboot the PC
<ESC> = Continue
NOTE: At this point you must reboot the computer in order for the new EDID information to be read and the
new preferred resolution to become available.
If the EDID programming failed, the following message will be displayed:
EDID Prog failed!
Disconnect DVI in
& loop thru conns
<ESC> = Continue
It this message persists and there is no DVI source or display device connected to ImagePRO, please contact our
customer service for technical support.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
55
Save System State
This command explicitly saves all settings in the system state submenu so they may be restored at power up. This
command will also save the currently selected input channel as the default input selection upon power up. If the user
wants the ImagePRO to always power up and acquire and convert an input other than input one, the user must
perform a save system state command while the desired input is selected.
NOTE:
Configuration parameters entered in the system menu are saved in non-volatile memory by using the SAVE
SYSTEM STATE menu item. If the SAVE SYSTEM STATE menu item is not selected, the information will not
be restored upon the next system power up sequence.
Factory Reset
This command allows the user to reset the unit into its “from the factory” condition – deleting all saved user
information, input configurations, custom formats and views. When the command is executed, a confirmation menu
is displayed:
Clear all config,
formats, and views?
<SEL> = Yes
<ESC> = No
Pressing SEL causes the command to be executed, followed by a complete system reset. Pressing ESC returns to
the "Setup" menu.
NOTE:
Performing a Factory Reset will erase all user saved input configuration files, Views, Custom formats and
restores ImagePRO memory to its “from the factory” condition.
56
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Test Pattern Menu
This menu is invoked by pressing the TEST PAT button.
TEST PATTERNS
> Type
Raster Box
<val>
<val>
The type selection enables a test pattern or turns them off. The value choices are:
Off
H Ramp
V Ramp
100% Col Bars
75% Col bars
16x16 Grid
32x32 Grid
Burst
50% Gray
Gray Steps 1
Gray Steps 2
The raster box values are On or Off. Turning this value on causes the system to turn on a one-pixel border around
the output active area. This raster box includes gaps to allow the user to precisely align the input video to fill the
output raster.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
57
Zoom Menu
This menu is invoked by pressing the ZOOM button. The default zoom amount is 100%. By selecting Amount and
pressing SEL the user may increase zoom above 100% (zoom into the input Video) or decrease zoom below 100%
(zoom out). Independent zoom values are maintained for each input channel.
ZOOM
> Amount
Save View
Recall View
<val>
A View (certain zoom and pan settings) associated with the currently selected input channel may be saved from this
menu. After the desired zoom setting is selected use the encoder knob to scroll to Save View and press SEL. The
current zoom setting will be saved. This View will be restored on power up for the corresponding input channel. The
user may also change/save the View Pan settings for the currently selected input channel from the Pan Menu. Recall
view allows the user to recall the saved view for the selected input channel.
Pan Menu
This menu is invoked by pressing the PAN button.
PAN
> Horizontal
Vertical
Diag \
Diag /
Save View
Recall View
<hVal>
<vVal>
<h/vVal>
<h/vVal>
There are four selections available for panning, as shown in the menu diagram. The values range from -100% to
+100%. 0% pan means that the center of the input image coincides with the center of the output image for the given
pan direction. For vertical pan, an increasing value moves the image downward. For horizontal pan, an increasing
value moves the image to the right. The screen will be properly updated when SEL is pressed in any selection line.
Independent pan (and zoom) values are maintained for each input channel.
A View (certain zoom and pan settings) associated with the currently selected input channel may also be saved from
this menu. After the desired pan settings are selected use the encoder knob to scroll to Save View and press SEL.
The current pan settings will be saved. This View will be restored on power up for the corresponding input channel.
The user may also change/save the Zoom settings for the currently selected input channel from the Zoom Menu.
Recall view allows the user to recall the saved view for the selected input channel.
Pan and Zoom Reset
Pressing and holding the PAN and ZOOM buttons simultaneously will restore the pan values to 0% and zoom value
to 100% for the currently selected input channel.
58
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
59
4
CHAPTER FOUR
Remote Commands
What you will find in this chapter…
‰
‰
‰
Serial Command Syntax
Remote Commands
ImagePROTM Command List/Description
Model IP-2003
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
61
62
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Serial Command Syntax
Serial Parameters
The following are the default parameter settings for serial communication.
Baud Rate is 38.4K.
Parity is NONE.
Stop Bit is 1.
Data Bit is 8.
For RS-232 signal connections, refer to Chapter 2 – Installation.
RS232 Mode
The ImagePRO will respond with a '#' prompt when the command processor is ready for a command.
The command syntax is shown below
cmd arg1 arg2 … argn<CR>
cmd
arg
<CR>
cmd is any valid Graphics Board command, typically 2 to 6 alphabetic (non numeric) characters.
arg1, arg2, … argn are required or optional parameters depending on the command used.
carriage return (ASCII 13) terminates the command
A space (ASCII 32) must be inserted between the command and any arguments that follow. A space must also be
inserted between all argument parameters except for the last argument in the chain.
All commands in RS232 mode must be terminated with a carriage return (ASCII 13). The carriage return will tell the
command processor to begin execution of the command. See below for a decription of error codes.
Query commands will return the following:
=result
#
The '=' indicates a result from a command is following. The 'result' will follow directly after the '='. The value of the
result will vary depending on the query command used. A new line will be generated and the prompt will indicate the
system is ready for a new command.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
63
ImagePROTM Remote Commands
Resolution Remote Commands
RESH
RESI nn
RESI?
RESO nn
RESO?
Query list of available Resolutions
Set current Input Resolution
Query Input Resolution
Set Output Resolution
Query Output Resolution
Input Remote Commands
ACQ mode
ACQ?
DINT in mode
DINT? in
PCOMP in mode
PCOMP? in
FREEZ mode
FREEZ?
IAR in n cn
IAR? in
IAUTOC
IBRT in nnn.n
IBRT? in
ICNT in nnn.n
ICNT? in
ICPHO in nn
ICPHO? in
ICLIST
ICDEL filename
ICREC in filename
ICRST in
ICSAV in filename
ICSP in mode
ICSP? in
ICUSE in
IEDGE in edge nnnn
IEDGE? In edge
IGM in
IGM? In
IHATV nnnn
IHATV?
IHPOS nnnn
IHPOS?
IHTOTAL nnnn
IHTOTAL?
IHUE in nnn
IHUE? in
ILB in mode
ILB? In
IRBRT in c nn.n
IRBRT? in c
IRCNT in c nn.n
IRCNT? in c
ISAT in nnn
ISAT? in
ISMP in n
64
Disable/Enable Auto acquisition mode
Query Auto acquisition mode
Sets De-interlacer mode
Query De-interlacer mode
Set Pulldown Compensation mode
Query Pulldown Compensation mode
Enables/disables freeze
Query freeze mode
Adjust Input Aspect Ratio
Query Input Aspect Ratio
Automatically Configure the Input
Set Input Brightness
Query Input Brightness
Set Input Contrast
Query Input Contrast
Set Input Sample Phase
Query Input Sample Phase
List all saved Input Configurations
Delete saved Input Configuration
Recall saved Input Configuration
Reset Input Configuration
Saves Input Configuration
Set Input Colorspace
Query Input Colorspace
Query Input Configuration Name used for a channel
Adjust Input Video top/bottom/left or right edge in Oversample mode
Query Input Video edge adjustment
Sets Input Gamma
Query Input Gamma for a channel
Set Input Horiz Active
Query Input Horiz Active
Set Input Horiz Position
Query Input Horiz Position
Set Input Horiz Total
Query Input Horiz Total
Adjust Input Hue
Query Input Hue
Set LetterBox mode
Query LetterBox mode
Set RGB Input Brightness
Query RGB Input Brightness
Set RGB Input Contrast
Query RGB Input Contrast
Adjust Input Saturation
Query Input Saturation
Adjust Input Sample mode
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
ISMP? in
ISYNC in mode
ISYNC? in
ISYNCSLICE in nnn
ISYNCSLICE? in
ITYPE in mode
ITYPE? in
IVATV nnnn
IVATV?
IVPOS nnnn
IVPOS?
IVTOTAL?
IVREC in
IVSAV in
LCK? in
RTE in
RTE?
Query Input Sample mode
Set Input Sync
Query Input Sync
Set Input Sync Slice Threshold
Query Input Sync Slice Threshold
Set Input Type
Query Input Type
Set Input Vert Active
Query Input Vert Active
Set Input Vert Position
Query Input Vert Position
Query Input Vert Total
Input Channel View Recall
Input Channel View Save
Query Lock status
Routes Input source
Query currently routed Input source
Output Remote Commands
GLMODE src type
GLMODE?
GLPHASE h sc
GLPHASE?
OBRT nnn.n
OBRT?
OCNT nnn.n
OCNT?
OCRST
OCSAV
OCSP mode
OCSP?
OEQ mode
OEQ?
OFR mode
OFR?
OGM n
OGM?
OHATV nnnn
OHATV?
OHPOS nnnn
OHPOS?
OHSYNC nnnn
OHSYNC?
OHTOTAL nnnn
OHTOTAL?
OHUE nnn
OHUE?
OPDL mode
OPDL?
OSAT nnn.n
OSAT?
OSER mode
OSER?
OSHRP n
OSHRP?
OSOG n
OSOG?
OSYNC n
OSYNC?
OUSCN nn
Set Genlock Source and Type
Query Genlock Source and Type
Set Genlock H Phase and SC Phase
Query Genlock H Phase and SC Phase
Adjust Output Brightness
Query Output Brightness
Adjust Output Contrast
Query Output Contrast
Reset Output Configuration
Save Output Configuration
Set Output Colorspace
Query Output Colorspace
Set Output Equalization mode
Query Output Equalization mode
Set Output Flicker Reduce mode
Query Output Flicker Reduce mode
Set Output Gamma
Query Output Gamma
Set Output Horiz Active
Query Output Horiz Active
Set Output Horiz Position
Query Output Horiz Position
Set Output Horiz Sync
Query Output Horiz Sync
Set Output Horiz Total
Query Output Horiz Total
Adjust Output Hue
Query Output Hue
Set Output Pedestal mode
Query Output Pedestal mode
Adjust Output Saturation
Query Output Saturation
Set Output Serrations mode
Query Output Serrations mode
Set Output Sharpness
Query Output Sharpness
Output Sync On Green mode
Query Output Sync On Green mode
Set Output Sync type
Query Output Sync type
Set Output Underscan
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
65
OUSCN?
OTPM type raster
OTPM?
OVATV nnnn
OVATV?
OVPOS nnnn
OVPOS?
OVSYNC nnnn
OVSYNC?
OVTOTAL nnnn
OVTOTAL?
Query Output Underscan
Enables/disables Output test pattern and raster box
Query Output test pattern and raster box mode
Set Output Vert Active
Query Output Vert Active
Set Output Vert Position
Query Output Vert Position
Set Output Vert Sync
Query Output Vert Sync
Set Output Vert Total
Query Output Vert Total
Edit Custom Format Remote Commands
EFLIST
EFRES nn
EFRES?
EFRESH
EFHTOTAL nnnn
EFHTOTAL?
EFHATV nnnn
EFHATV?
EFHFP nn
EFHFP?
EFHSYNC nn
EFHSYNC?
EFHRATE?
EFVTOTAL nnnn
EFVTOTAL?
EFVATV nnnn
EFVATV?
EFVFP nn
EFVFP?
EFVSYNC nn
EFVSYNC?
EFVRATE nnn.n
EFVRATE?
EFINT mode
EFINT?
EFSAV
EFDEL
List all saved custom formats
Set base resolution for custom format settings
Query base resolution for custom format settings
Query list of available Resolutions for custom format
Set Horiz Total for custom format
Query Horiz Total for custom format
Set Horiz Active for custom format
Query Horiz Active for custom format
Set Horiz Front Porch for custom format
Query Horiz Front Porch for custom format
Set Horiz Sync for custom format
Query Horiz Sync for custom format
Query Horiz Rate for custom format
Set Vert Total for custom format
Query Vert Total for custom format
Set Vert Active for custom format
Query Vert Active for custom format
Set Vert Front Porch for custom format
Query Vert Front Porch for custom format
Set Vert Sync for custom format
Query Vert Sync for custom format
Query Vert Rate for custom format
Query Vert Rate for custom format
Set Interlace mode for custom format
Query Interlace mode for custom format
Save custom format
Delete saved custom format
System and Ethernet Remote Commands
DMSG mode
Disable/Enable Debug messages
DMSG ?
Query Debug message mode
EDHCP
Set Ethernet DHCP mode
EDHCP?
Query Ethernet DHCP mode
EECHO mode
Disable/Enable echo on Ethernet telnet window
EIP xxx.xxx.xxx.xxx yyy.yyy.yyy.yyy zzz.zzz.zzz.zzz
Sets Ethernet IP address, Subnet mask and default Gateway IP
EIP?
Query Ethernet IP address
EMAC?
Query Ethernet MAC address
SBAUD n
Adjust Serial Baud Rate
SBAUD?
Query Serial Baud Rate
SYSAV
Save System State
HELP [op]
Displays command list: op[A..Z]
LOADR
Run Loader Program
RESET
Factory Reset ImagePRO
66
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Logo Remote Commands
LOGOD
LOGOL
LOGOS
LOGOI
Delete currently saved Logo image from Flash
Load currently saved Logo image from Flash to Logo Frame store buffer
Save current output image as Logo image to Flash
Query Logo resolution
Effects Related Commands
TRN type n
TRN?
Selects transition type and time
Query transition type and time
Pan / Zoom / View Remote Commands
PANH nnn.n
PANH?
PANHV hhh.h vvv.v
PANHV?
PANV nnn.n
PANV?
VIEW? nn
VIEWD nn
VIEWR nn
VIEWS nn
VIEWI? in
VIEWIR
VIEWIS in
ZOOM nnn.n
ZOOM?
Set Output Horizontal Pan
Query Output Horizontal Pan Setting
Set Output Diagonal Pan
Query Output Diagonal Pan
Set Output Vertical Pan
Query Output Vertical Pan Setting
Query View settings
Delete View
Recall View
Save View
Query Input channel View settings
Recall current Input channel View
Save Input channel View
Selects zoom factor
Query zoom factor
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
67
ImagePROTM Command List/Description
Resolution Remote Commands
Command:
RESH
Description:
Parameters:
Returns:
Example:
Query the available resolution list for the ImagePRO.
None
All available resolutions in the format:
n : HxV @F (example: 20 : 1024x768 @59.94)
RESH (Query all available resolutions)
Command:
RESI nn
Description:
Set current channel’s Input Resolution. If Auto Acquire is On, setting Input resolution with this
command may be overridden.
nn - Input Resolution (use RESH command for resolution list)
Parameters:
Query:
RESI? in
Returns the Input Resolution for the specified channel in the format
= nn
Example:
RESI 1 (Set Input Resolution of currently selected input channel to resolution index 1 (NTSC(480i))
RESI? 1 (Queries Input Resolution for channel 1)
Command:
RESO nn
Description:
Set Output Resolution.
Parameters:
nn - Output Resolution (use RESH command for resolution list)
Query:
RESO?
Returns the Output Resolution in the format
= nn
Example:
RESO 1(Set Output Resolution to resolution index 1 (NTSC(480i))
RESO? (Queries Output Resolution)
68
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Input Remote Commands
Command:
ACQ mode
Description:
Turns Auto acquisition mode off/on.
Parameters:
mode [0 | 1] Off | On
Query:
ACQ?
Returns Auto acquisition mode in the format
= mode
Example:
ACQ 0 (Turns auto acquisition mode off)
ACQ? (Queries for auto acquisition mode)
Command:
DINT in mode
Description:
Parameters:
Sets De-interlacer mode. Motion de-interlacer mode is only available for Interlaced inputs
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
mode - De-interlacer mode [0-1] Motion | Fld->Frm
Query
DINT? in
Returns De-interlacer mode in the format
= mode
Example:
DINT 1 1 (Set De-interlacer mode to Fld->Frm)
DINT? 1 (Queries De-interlacer mode for channel 1)
Command:
PCOMP in mode
Description:
Parameters:
Sets the de-interlacer’s Pulldown Compensation mode.
in - Input chnl [1-4] chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
mode - [0 | 1] Disable | Enable
Query:
PCOMP? in
Returns the de-interlacer’s Pulldown Compensation mode in the format
= mode
Example:
PCOMP 1 0
(Disables Pulldown Compensation mode for channel 1.)
PCOMP? 2
(Queries Pulldown Compensation mode of channel 2.)
Command:
FREEZ mode
Description:
Enables/disables output Freeze
Parameters:
mode - [0 | 1] Disable | Enable
Query:
FREEZ?
Returns the Freeze mode in the format
= mode
Example:
FREEZ 1 (Freezes Image)
FREEZ? (Queries Freeze mode)
Command:
IAR in n cn
Description:
Parameters:
Adjust Input Aspect Ratio.
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
69
n - Input Aspect Ratio: n[0-5], 1:1 | 3:2 | 4:3 | 5:4 | 16:9 | Custom
cn - (Optional) Custom Input Aspect Ratio: (0.75 – 3.00)
NOTE: cn parameter is not required unless user selects Custom Input Aspect Ratio (i.e. n = 5)
Query:
IAR? in
Returns the Input Aspect Ratio of specified source in the format
= n cn
Example:
IAR 1 5 2.0 (Sets aspect ratio of channel 1 to Custom and sets the custom aspect ratio to 2.0)
IAR? 1 (Queries Input aspect ratio of channel 1)
Command:
IAUTOC
Description:
Parameters:
Example:
Auto Configure currently routed input. Only available if Input Sample mode is 1:1
None
IAUTOC (Auto Configures current input source)
Command:
IBRT in nnn.n
Description:
Parameters:
Adjusts the Input Brightness value of the specified source.
in - Input chnl [1-3]
nnn.n - Brightness value; Range 75 to 125%
Query:
IBRT? in
Returns the Input Brightness value of the specified source in the format
= nnn.n
Example:
IBRT 2 110
(Adjusts input 2 Brightness to be 110%.)
IBRT? 2
(Queries Input Brightness of channel 2.)
Command:
ICNT in nnn.n
Description:
Adjusts the Input Contrast values of the specified source.
Parameters:
in - Input chnl [1-3]
nnn.n - Contrast value; Range 75 - 125%
Query:
ICNT? in
Returns the Input Contrast values of the specified source in the format
= nnn.n
Example:
ICNT 1 100
(Adjusts input 1 Contrast to be 100%.)
ICNT? 1
(Queries Input Contrast of channel 1.)
Command:
ICPHO in nn
Description:
Parameters:
Adjusts the Input Clock Phase Offset.
in - Input chnl [1-3]
nn Phase value; [-16..15]
Query:
ICPHO? in
Returns the Input Clock Phase Offset in the format
= nn
Example:
ICPHO 1 15
(Adjusts the Input clock phase offset manually to 15 on input 1.)
ICPHO? 1
(Queries the Input clock phase offset of channel 1.)
Command:
70
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
ICLIST
Description:
Parameters:
Returns:
Example:
Lists the names of all saved Input configurations.
None
List the names of saved Input configurations, one name per line.
ICLIST (Lists all saved Input configurations.)
Command:
ICDEL filename
Description:
Parameters:
Example:
Delete saved Input configuration.
filename – name of configuration to be deleted (not case sensitive).
ICDEL file1 (Deletes Input configuration stored as FILE1.)
Command:
ICREC in filename
Description:
Parameters:
Example:
Recalls saved Input Configuration.
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
filename – configuration that is being recalled (not case sensitive).
ICREC 3 file1 (Recalls Input configuration stored as file1 for channel 3.)
Command:
ICRST in
Description:
Parameters:
Example:
Reset Input Configuration for the specified channel.
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
ICRST 1 (Resets Input Configuration for channel 1)
Command:
ICSAV in filename
Description:
Parameters:
Example:
Saves Input configuration to non-volatile memory.
filename – name given to configuration when it is stored. This filename is translated to all upper
case characters. If same input configuration name exist, it will be overwritten.
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
ICSAV 3 file1 (saves Input configuration as FILE1 for channel 3.)
Command:
ICUSE in
Description:
Parameters:
Returns:
Example:
Query the name of the Input configuration used for the specified channel.
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
Name of the Input configuration used (if any)
ICUSE 1 (Lists the name of the saved Input configurations used by channel 1.)
Command:
ICSP in mode
Description:
Parameters:
Sets Input Colorspace for the selected input channel. SMPTE, BETA, and M-II colorspace available
only if input type is YPbPr
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
mode - [0-3] RGB | SMPTE | BETA | M-II
Query:
ICSP? in
Returns the Input Colorspace for the specified input channel in the format
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
71
= mode
Example:
ICSP 1 2 (Sets YPbPr input colorspace to Beta for channel 1)
ICSP? 2 (Queries channel 2 for Input Colorspace.)
Command:
IEDGE in edge nnnn
Description:
Parameters:
Set Input Edge in oversample mode. The minimum and maximum limit is dependent on the input
resolution.
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
edge (L|R|T|B)
nnnn - Input edge: nnnn
if edge=L [Input H Sync-( Input H Sync + (Input H total X 0.25))]
if edge=R [((H Total – H Front Porch))X0.9 -(H total)]
if edge= T [ Vsync – (Vsync +128)]
if edge= B [ (V total –64) – Vtotal)]
Query:
IEDGE? in edge
Returns the Input Edge value in the format
= nnnn
Example:
IEDGE 1 R 1024 (Set Input Right Edge to 1024)
IEDGE? 1 L
(Queries Input Left Edge value)
Command:
IGM in n
Description:
Parameters:
Sets Input Gamma for the selected input channel
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
n - [1.0-3.0] increment 0.1
Query:
IGM? in
Returns the Input Gamma for the specified input channel in the format
=n
Example:
IGM 1 2.2 (Set Input gamma value to 2.2 for channel 1)
IGM? 2
(Queries channel 2’s Input gamma value.)
Command:
IHATV in nnnn
Description:
Parameters:
Set Input Horizontal Active. The minimum and maximum limit is dependent on the input
resolution.
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
nnnn - Input Horizontal Active: nnnn[(Actual Input H Active * 2/10, minimum of 150) - +(Actual Input
H Active * 6/5, maximum of Input H Total – Input H Sync)]
Query:
IHATV? in
Returns the Input Horizontal Active in the format
= nnnn
Example:
IHATV 1 1024 (Set Input Horizontal Active for channel 1 to 1024)
IHATV? 1
(Queries Input Horizontal Active for channel 1)
Command:
IHPOS in nnnn
Description:
Parameters:
72
Set Input Horizontal Position. The minimum and maximum limit is dependent on the input
resolution.
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
nnnn - Input Horizontal Position: nnnn[(Input H Sync) - +(H Total - H Active)]
Query:
IHPOS? in
Returns the Input Horizontal Position in the format
= nnnn
Example:
IHPOS 1 296 (Set Input Horizontal Position for channel 1 to 296)
IHPOS? 1
(Queries Input Horizontal Position for channel 1)
Command:
IHTOTAL in nnnn
Description:
Parameters:
Set Input Horizontal Total. The minimum and maximum limit is dependent on the input resolution.
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
nnnn - Input Horizontal Total: nnnn[(Actual Input H Total * 2/5) - +(Actual Input H Total * 9/5)]
Query:
IHTOTAL? in
Returns the Input Horizontal Total in the format= nnnn
Example:
IHTOTAL 1 1344 (Set Input Horizontal Total for channel 1 to 1344)
IHTOTAL? 1
(Queries Input Horizontal Total for channel 1)
Command:
IHUE in nnn
Description:
Parameters:
Adjusts Input Hue. Only applicable for non RGB source.
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
nnn - Input Hue (-180 - +180)
Query:
IHUE? in
Returns the Input Hue in the format
= nnn
Example:
IHUE 1 170 (Adjusts input hue of channel 1 to 170)
IHUE? 1
(Queries Input Hue of channel 1)
Command:
ILB in mode
Description:
Parameters:
LetterBox Mode
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
mode - Disable/Enable letterbox mode (0 / 1)
Query:
ILB? in
Returns the LetterBox Mode in the format
= mode
Example:
ILB 1 1 (Enables Letterbox mode of channel 1)
ILB? 1 (Queries LetterBox mode of channel 1)
Command:
IRBRT in c nnn.n
Description:
Parameters:
Adjusts the Input RGB Brightness value.
in Input chnl [1-3]
cColor [R|G|B]
nnn.n - Brightness value; Range –25% to +25%
Query:
IRBRT? in c
Returns the Input RGB Brightness value of the specified source in the format
= nnn.n
Example:
IRBRT 1 R 10
(Adjusts input 1 Red Brightness to be +10%.)
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
73
IRBRT? 1 R
(Queries input Red Brightness of channel 1.)
Command:
IRCNT in c nnn.n
Description:
Parameters:
Adjusts the Input RGB Contrast values.
in Input chnl [1-3]
cColor [R|G|B]
nnn.n - Contrast value; Range –25% to +25%
Query:
IRCNT? in c
Returns the Input RGB Contrast values of the specified source in the format
= nnn.n
Example:
IRCNT 1 B -15 (Adjusts input 1 Blue Contrast to be -15%.)
IRCNT? 1 B
(Queries input Blue Contrast of Channel 1.)
Command:
ISAT in nnn
Description:
Parameters:
Adjust Input Saturation.
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
nnn - Input Saturation (75 – 125 if input is YPbPr, 0 – 150 otherwise)
Query:
ISAT? in
Returns the Input Saturation in the format
= nnn
Example:
ISAT 1 100 (Adjusts Input Saturation of channel 1 to 100)
ISAT? 1
(Queries Input Saturation of channel 1)
Command:
ISMP in n
Description:
Parameters:
Adjust Input Sample Mode.
in - Input chnl (1-3)
n - Input Sample Mode: n[0-1], Oversample | 1:1
NOTE: Some input’s sample mode can only be oversample, some can
only be 1:1.
Query:
ISMP? in
Returns the Input Sample Mode in the format
=n
Example:
ISMP 1 0 (Adjusts Input Sample mode of channel 1 to OverSample)
ISMP? 1 (Queries Input Sample Mode of channel 1)
Command:
ISYNC in mode
Description:
Adjusts the Input Sync selection.
Parameters:
in - Input chnl [1-3]
mode - Mode [0|1|2|3], Auto|H/V|CSync|SOG
Query:
ISYNC? in
Returns the Input Sync selected for the specified input channel in the format
= mode
Example:
ISYNC 1 1 (Sets Scaler to expect H/V sync on input channel 1.)
ISYNC? 1 (Queries Input Sync selected for channel 1)
Command:
74
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
ISYNCSLICE in nnn
Description:
Adjusts the Input Sync Slice Threshold selection.
Parameters:
in - Input chnl [1-3]
nnn Sync Slice Threshold [20 – 280mV (in steps of 10)]
Query:
ISYNCSLICE? in
Returns the Input Sync Slice Threshold selected for the specified input channel in the format
= nnn
Example:
ISYNCSLICE 1 60 (Sets Sync Slicer threshold to 60mV for channel 1.)
ISYNCSLICE? 1
(Queries Input Sync Slicer threshold for channel 1)
Command:
ITYPE in mode
Description:
Sets the Input Type. Note: If Auto Acquire is On, setting Input type with this command may be
overridden. Input Type DVI is only available on input channel 1 for ImagePRO-SDI and ImagePROHD units.
Parameters:
in - Input chnl [1-3]
mode - Mode [0|1|2|3], RGB | YPbPr | NTSC/PAL/SECAM | DVI (DVI available only on chnl 1 for
ImagePRO-SDI and ImagePRO-HD units)
Query:
ITYPE? in
Returns the Input Type selected for the specified input channel in the format
= mode
Example:
ITYPE 1 2 (Sets Input type to YPbPr on input channel 1.)
ITYPE? 1 (Queries Input type for channel 1)
Command:
IVATV nnnn
Description:
Parameters:
Set Input Vertical Active. The minimum and maximum limit is dependent on the input resolution.
nnnn - Input Vertical Active: nnnn[(Actual Input V Active * 2/10, absolute minimum of 150) –
+(Actual Input V Active *6/5, absolute maximum of Input V Total – Input V Sync)]
Query:
IVATV?
Returns the Input’s Vertical Active value in the format
= nnnn.
Example:
IVATV 768 (Set Input Vertical Active to 768)
IVATV?
(Queries Input Vertical Active)
Command:
IVPOS nnnn
Description:
Set Input Vertical Position. The minimum and maximum limit is dependent on the input
resolution.
nnnn - Input Vertical Position: nnnn[(Input V Sync) - +(Input V Total – Input V Active)]
Parameters:
Query:
IVPOS?
Returns the Input’s Vertical Position value in the format
= nnnn
Example:
IVPOS 35 (Set Input Vertical Position to 35)
IVPOS? (Queries Input Vertical Position)
Command:
IVTOTAL?
Description:
Parameters:
Returns:
Query Input Vertical Total.
None
nnnn - Input Vertical Total
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
75
Example:
IVTOTAL? (Queries Input Vertical Total)
Command:
IVREC in
Description:
Parameters:
Example:
Input Channel View Recall.
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
IVREC 1 (Recalls Input Channel View of channel 1)
Command:
IVSAV in
Description:
Parameters:
Example:
Input Channel View Save.
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
IVSAV 1 (Saves the Input Channel View for channel 1)
Command:
LCK? in
Description:
Parameters:
Returns:
Example:
Queries Lock Status for specified input channel.
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
n - Lock Status (0 – 3) Not Locked | Locked (Match Format) | Locked (Best Guessed) | Locked
(using saved Input Configuration)
LCK? 1 (Queries Lock status for channel 1)
Command:
RTE in
Description:
Selects and routes input to be processed. Chnl 4 is only available on ImagePRO-SDI
and ImagePRO-HD.
in Input [1-5] 1,2,3, 4=SDI, 5=Black or Logo
Parameters:
Query:
RTE?
Returns the input channel that is routed in the format
= in
Example:
RTE 2 (Selects input 2 for processing.)
Example:
RTE? (Queries the input channel that is routed.)
76
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Output Remote Commands
Command:
GLMODE src type
Description:
Parameters:
Sets Genlock Source and Genlock Type
src [0-4], Freerun | Input Video | H+V Sync | C Sync | Black Burst
type [1-3], V Lock | HV Lock | HVScLock(Full lock)
Query:
GLMODE?
Returns the Genlock Source and Genlock Type in the format
= src type
Example:
GLMODE 1 2 (Set Genlock Source to Input Video and Type to HV Lock)
GLMODE? (Queries Genlock Source and Genlock Type)
Command:
GLPHASE h sc
Description:
Parameters:
Sets Genlock Horizontal Phase and SubCarrier Phase
h – H Phase [ (-Input H Total/2) – (+Input H Total/2) ]
sc – SC Phase [-180 - +180]
Query:
GLPHASE?
Returns the Genlock Horizontal Phase and SubCarrier Phase in the format
= h sc
Example:
GLPHASE 150 -100 (Set Genlock H Phase to 150 and SC Phase to -100)
GLPHASE?
(Queries Genlock H Phase and SC Phase)
Command:
OBRT nnn.n
Description:
Adjust Output Brightness. Only applicable if output is NTSC/PAL
Parameters:
nnn.n - Output Brightness (100.0 – 114.0)
Query:
OBRT?
Returns the Output Brightness in the format
= nnn.n
Example:
OBRT 100 (Adjusts Output Brightness to 100)
OBRT?
(Queries Output Brightness)
Command:
OCNT nnn.n
Description:
Adjust Output Contrast. Only applicable if output is NTSC/PAL
Parameters:
nnn.n - Output Contrast (75.0 – 125.0)
Query:
OCNT?
Returns the Output Contrast in the format
= nnn.n
Example:
OCNT 100 (Adjusts Output Contrast to 100)
OCNT?
(Queries Output Contrast)
Command:
OCRST
Description:
Reset Output Configuration.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
77
Parameters:
Example:
None
OCRST (Reset Output Configuration)
Command:
OCSAV
Description:
Parameters:
Example:
Save Output Configuration to non-volatile memory.
None
OCSAV (Save Output Configuration)
Command:
OCSP mode
Description:
Sets Output Colorspace mode.
Parameters:
mode - [0-1] RGB | YPbPr
Query:
OCSP?
Returns the Output Colorspace mode in the format
= mode
Example:
OCSP 1 (Sets Output colorspace to YPbPr)
OCSP? (Queries Output Colorspace.)
Command:
OEQ mode
Description:
Output Equalization mode. Only applicable if output is interlaced.
Parameters:
mode – Disable/ Enable equalization mode (0 / 1)
Query:
OEQ?
Returns the Output Equalization mode in the format
= mode
Example:
OEQ 0 (Enables Output Equalization mode)
OEQ? (Queries Output Equalization mode)
Command:
OFR mode
Description:
Output Flicker Reduce mode. Only applicable if output is interlaced.
Parameters:
mode – Disable/Enable flicker reduce mode (0 / 1)
Query:
OFR?
Returns the Output Flicker Reduce mode in the format
= mode
Example:
OFR 0 (Enables Output Flicker Reduce mode)
OFR? (Queries Output Flicker Reduce mode)
Command:
OGM n
Description:
Set Output Gamma.
Parameters:
n - Output Gamma: n[1.0 – 3.0]
Query:
OGM?
Returns the Output Gamma value in the format
=n
Example:
OGM 1.0 (Set Output Gamma to 1.0)
OGM? (Queries Output Gamma)
78
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Command:
OHATV nnnn
Description:
Parameters:
Set Output Horizontal Active. The minimum and maximum limit is dependent on the output
resolution.
nnnn - Output Horizontal Active: nnnn[ (Actual Output H Active * 2/10, with absolute minimum
value of 150) - +(Actual Output H Active * 6/5, with absolute maximum of Output H Total – Output H
Sync)]
Query:
OHATV?
Returns the Output Horizontal Active value in the format
= nnnn
Example:
OHATV 1024 (Set Output Horizontal Active to 1024)
OHATV?
(Queries Output Horizontal Active)
Command:
OHPOS nnnn
Description:
Set Output Horizontal Position. The minimum and maximum limit is dependent on the output
resolution.
nnnn - Output Horizontal Position: nnnn[(Output H Sync) - +(Output H Active )]
Parameters:
Query:
OHPOS?
Returns the Output Horizontal Position value in the format
= nnnn
Example:
OHPOS 296 (Set Output Horizontal Position to 296)
OHPOS?
(Queries Output Horizontal Position)
Command:
OHSYNC nnnn
Description:
Parameters:
Set Output Horizontal Sync Width. The minimum limit is 4 and maximum limit is dependent on the
output resolution.
nnnn - Output Horizontal Sync Width: nnnn[4 - (Output H Total -Output H Active – Output
Horizontal Front Porch –4)]
Query:
OHSYNC?
Returns the Output Horizontal Sync Width value in the format
= nnnn
Example:
OHSYNC 120 (Set Output Horizontal Sync Width to 120)
OHSYNC?
(Queries Output Horizontal Sync Width)
Command:
OHTOTAL nnnn
Description:
Parameters:
Set Output Horizontal Total. The minimum and maximum limit is dependent on the output
resolution.
nnnn - Output Horizontal Total: nnnn[(Output Hsync + Output Hactive + (Output Hpos – Output
Hsync)) - +(Actual Output H Total * 9/5)]
Query:
OHTOTAL?
Returns the Output Horizontal Total value in the format
= nnnn
Example:
OHTOTAL 1344 (Set Output Horizontal Total to 1344)
OHTOTAL?
(Queries Output Horizontal Total)
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
79
Command:
OHUE nnn
Description:
Adjust Output Hue. Only applicable if output is NTSC. n/a if PAL
Parameters:
nnn - Output Hue (-22.0 - +22.0)
Query:
OHUE?
Returns the Output Hue value in the format
= nnn
Example:
OHUE 20 (Adjust Output Hue to 20)
OHUE? (Queries Output Hue)
Command:
OPDL mode
Description:
Adjust Output Pedestal mode. Only applicable if output is NTSC. n/a if PAL
Parameters:
mode - Disable/Enable pedestal mode (0 / 1)
Query:
OPDL?
Returns the Output Pedestal mode in the format
= mode
Example:
OPDL 0 (Disable Output Pedestal mode)
OPDL? (Queries Output Pedestal mode)
Command:
OSAT nnn.n
Description:
Adjust Output Saturation. Only applicable if output is NTSC/PAL
Parameters:
nnn.n - Output Saturation (-75.0 - +125.0)
Query:
OSAT?
Returns the Output Saturation value in the format
= nnn.n
Example:
OSAT 100 (Adjust Output Saturation to 100)
OSAT?
(Queries Output Saturation)
Command:
OSER mode
Description:
Output Serrations mode
Parameters:
mode - Disable/Enable serrations mode (0 / 1)
Query:
OSER?
Returns the Output Serrations mode in the format
= mode
Example:
OSER 0 (Disable Output Serrations mode)
Example:
OSER? (Queries Output Serrations mode)
Command:
OSHRP nnn
Description:
Set Output Sharpness
Parameters:
nnn - Sharpness: nnn[-10 - +10]
Query:
OSHRP?
Returns the Output Sharpness value in the format
= nnn
Example:
OSHRP 10 (Set Output Sharpness value to 10)
80
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
OSHRP?
(Queries Output Sharpness)
Command:
OSOG n
Description:
Output Sync On Green mode.
Parameters:
n - Output SOG: n[0-2] Off | Standard | Tri-level
Query:
OSOG?
Returns the Output Sync On Green mode in the format
=n
Example:
OSOG 0 (Turns off Output Sync On Green mode)
OSOG? (Queries Output Sync On Green mode)
Command:
OSYNC n
Description:
Set Output Sync type.
Parameters:
n - Output Sync: n[0-4], Csync| +H+V | +H-V | -H+V | -H-V
Query:
OSYNC?
Returns the Output Sync type in the format
=n
Example:
OSYNC 0 (Set Output Sync type to Csync)
OSYNC? (Queries Output Sync type)
Command:
OUSCN nn
Description:
Set Output Underscan.
Parameters:
nn - Output Underscan: nn[0% - 15%]
Query:
OUSCN?
Returns the Output Underscan value in the format
= nn
Example:
OUSCN 10 (Set Output Underscan to 10%)
OUSCN? (Queries Output Underscan)
Command:
OTPM type rast
Description:
Parameters:
Sets Internal Test pattern mode and raster box mode.
type - Test Pattern type: type[0..10] 0=Off, 1=H Ramp, 2=V Ramp, 3=100% Col Bars, 4=75% Col
bars,5=16x16 Grid, 6=32x32 Grid, 7=Burst, 8=50% Gray, 9=Gray Steps 1, 10=Gray Steps 2
rast - Raster Box: rast[0-1] On | Off
Query:
OTPM?
Returns the Test pattern mode and raster box mode in the format
= type rast
Example:
OTPM 9 0 (Selects Gray Steps 1 test pattern with raster off)
OTPM? (Query test pattern mode and with raster box mode)
Command:
OVATV nnnn
Description:
Parameters:
Set Output Vertical Active. The minimum and maximum limit is dependent on the output resolution.
nnnn - Output Vertical Active: nnnn[ (Actual Output V Active * 2/10, with absolute minimum value
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
81
of 150) - +(Actual Output V Active *6/5, with absolute maximum value of Output V Total – Output V
Sync)]
Query:
OVATV?
Returns the Output Vertical Active value in the format
= nnnn
Example:
OVATV 768 (Set Output Vertical Active to 768)
OVATV?
(Queries Output Vertical Active)
Command:
OVPOS nnnn
Description:
Set Output Vertical Position. The minimum and maximum limit is dependent on the output
resolution.
nnnn - Output Vertical Position: nnnn[ (Output V Sync) - +(Output V Active)]
Parameters:
Query:
OVPOS?
Returns the Output Vertical Position value in the format
= nnnn
Example:
OVPOS 35 (Set Output Vertical Position to 35)
OVPOS? (Queries Output Vertical Position)
Command:
OVSYNC nnnn
Description:
Parameters:
Set Output Vertical Sync Width. The minimum limit is 2 and maximum limit is dependent on the
output resolution.
nnnn - Output Vertical Sync Width: nnnn[2-(Output V Total -Output V Active – Output Vertical Front
Porch –2)]
Query:
OVSYNC?
Returns the Output Vertical Sync Width value in the format
= nnnn
Example:
OVSYNC 6 (Set Output Vertical Sync Width to 6)
OVSYNC?
(Queries Output Vertical Sync Width)
Command:
OVTOTAL nnnn
Description:
Parameters:
Set Output Vertical Active. The minimum and maximum limit is dependent on the output
resolution.
nnnn - Output Vertical Total: nnnn[ (Output Vsync + Output Vactive + (Output Vpos – Output
Vsync)) - +(Actual Output V Total * 9/5)]
Query:
OVTOTAL?
Returns the Output Vertical Total value in the format
= nnnn
Example:
OVTOTAL 806 (Set Output Vertical Total to 806)
OVTOTAL?
(Queries Output Vertical Total)
82
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Edit Custom Format Remote Commands
Command:
EFLIST
Description:
Parameters:
Returns:
Example:
Lists the names of all saved custom formats.
None
List the names of saved custom formats, one name per line.
EFLIST (Lists all saved custom formats.)
Command:
EFRES nn
Description:
Set base resolution for custom formats. All parameters for custom format will be loaded using the
specified resolution.
nn - Resolution (use RESH command for resolution list)
Parameters:
Query:
EFRES?
Returns the base resolution used for custom formats settings in the format
= nn
Example:
EFRES 1 (Load custom format settings with resolution index 1 values)
EFRES? (Query the base resolution for custom format settings)
Command:
EFRESH
Description:
Parameters:
Returns:
Example:
Query the available resolution list for custom format.
None
All available resolutions in the following format:
n : HxV @F (example: 18 : 1024x768 @59.94)
EFRESH (Query all available resolutions)
Command:
EFINT mode
Description:
Set custom format to be non-interlaced or interlaced format.
Parameters:
mode - [0 | 1] Non-Interlaced | Interlaced
Query:
EFINT?
Returns the interlace mode of the custom format in the format
= mode
Example:
EFINT 1 (Set custom format to be interlaced)
EFINT? (Query the interlace mode for the custom format)
Command:
EFHTOTAL nnnn
Description:
Set custom format’s Horizontal Total value.
Parameters:
nnnn - H Total [640 - +(162000 / H Rate)]
Query:
EFHTOTAL?
Returns the custom format’s Horizontal Total value in the format
= nnnn
Example:
EFHTOTAL 1344 (Set custom format H Total as 1344)
EFHTOTAL?
(Query the custom format’s H Total value)
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
83
Command:
EFHATV nnnn
Description:
Set custom format’s Horizontal Active value.
Parameters:
nnnn - H Active [500 - +(H Total - H Sync - H Front Porch)]
Query:
EFHATV?
Returns the custom format’s Horizontal Active value in the format
= nnnn
Example:
EFHATV 1024 (Set custom format H Active as 1024)
EFHATV?
(Query the custom format’s H Active value)
Command:
EFHFP nn
Description:
Set custom format’s Horizontal Front Porch value.
Parameters:
nn - H Front Porch [4 - +( H Total - H Active - H Sync - 4)]
Query:
EFHFP?
Returns the custom format’s Horizontal Front Porch value in the format
= nn
Example:
EFHFP 5 (Set custom format H Front Porch as 5)
EFHFP? (Query the custom format’s H Front Porch value)
Command:
EFHSYNC nn
Description:
Set custom format’s Horizontal Sync value.
Parameters:
nn - H Sync [4 - +( H Total - H Active - H Front Porch - 4)]
Query:
EFHSYNC?
Returns the custom format’s Horizontal Sync value in the format
= nn
Example:
EFHSYNC 5 (Set custom format H Sync as 5)
EFHSYNC? (Query the custom format’s H Sync value)
Command:
EFHRATE?
Description:
Parameters:
Returns:
Example:
Query custom format’s Horizontal Rate value (kHz).
None
nn.nn - H Rate
EFHRATE? (Query custom format’s H Rate value)
Command:
EFVTOTAL nnnn
Description:
Set custom format’s Vertical Total value.
Parameters:
nnnn - V Total [480 - 4096]
Query:
EFVTOTAL?
Returns the custom format’s Vertical Total value in the format
= nnnn
Example:
EFVTOTAL 512 (Set custom format V Total as 512)
EFVTOTAL?
(Query the custom format’s V Total value)
84
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Command:
EFVATV nnnn
Description:
Set custom format’s Vertical Active value.
Parameters:
nnnn - V Active [400 - +( V Total - V Sync - V Front Porch)]
Query:
EFVATV?
Returns the custom format’s Vertical Active value in the format
= nnnn
Example:
EFVATV 768 (Set custom format V Active as 768)
EFVATV?
(Query the custom format’s V Active value)
Command:
EFVFP nn
Description:
Set custom format’s Vertical Front Porch value.
Parameters:
nn - V Front Porch [1 - +( V Total - V Active - V Sync - 1)]
Query:
EFVFP?
Returns the custom format’s Vertical Front Porch value in the format
= nn
Example:
EFVFP 5 (Set custom format V Front Porch as 5)
EFVFP? (Query the custom format’s V Front Porch value)
Command:
EFVSYNC nn
Description:
Set custom format’s Vertical Sync value.
Parameters:
nn - V Sync [1 - +( V Total - V Active - V Front Porch - 1)]
Query:
EFVSYNC?
Returns the custom format’s Vertical Sync value in the format
= nn
Example:
EFVSYNC 2 (Set custom format V Sync as 2)
EFVSYNC? (Query the custom format’s V Sync value)
Command:
EFVRATE nnn.n
Description:
Set custom format’s Vertical Rate value.
Parameters:
nnn.nn - V Rate [20.00 – 120.00]
Query:
EFVRATE?
Returns the custom format’s Vertical Rate value in the format
= nnn.n
Example:
EFVRATE 59.94 (Set custom format V Rate as 59.94)
EFVRATE? (Query the custom format’s V Rate value)
Command:
EFSAV filename
Description:
Parameters:
Example:
Saves currently defined custom format to non-volatile memory.
filename – name given to custom format when it is stored. This filename is translated to all upper
case characters. If same custom format name exist, it will be overwritten.
EFSAV format1 (saves custom format as FORMAT1.)
Command:
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
85
EFDEL filename
Description:
Parameters:
Example:
86
Deletes saved custom format. This filename is translated to all upper case characters
filename – name of custom format to be deleted (translated to upper case).
EFDEL FORMAT1 (Deletes custom format with the name “FORMAT1”.)
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
System and Ethernet Remote Commands
Command:
DMSG mode
Description:
Sets Debug message display mode.
Parameters:
mode - DMSG mode [0-1] Off | On
Query:
DMSG?
Returns the Debug message display mode in the format
= mode
Example:
DMSG 1 (Sets Debug message mode to On)
DMSG? (Queries the DMSG mode)
Command:
EDHCP mode
Description:
Sets DHCP mode.
Parameters:
mode - DHCP mode [0-1] Off | On
Query:
EDHCP?
Returns the DHCP mode in the format
= mode
Example:
EDHCP 1 (Sets DHCP mode to On)
EDHCP? (Queries the DHCP mode)
Command:
EECHO mode
Description:
Parameters:
Example:
Disable/Enable echo on telnet window (for Microsoft Windows XP telnet window, echo must be
disabled.)
mode - Disable/Enable telnet echo (0 / 1)
EECHO 0 (Disable echo on telnet window)
Command:
EIP xxx.xxx.xxx.xxx yyy.yyy.yyy.yyy zzz.zzz.zzz.zzz
Description:
Parameters:
Set static Ethernet IP address, subnet mask and default Gateway IP
IP address – xxx.xxx.xxx.xxx (xxx: [0-255])
Subnet mask – yyy.yyy.yyy.yyy (yyy: [0-255])
Gateway IP – zzz.zzz.zzz.zzz (zzz: [0-255])
Query:
EIP?
Returns the Ethernet IP address, Subnet mask and Gateway IP in the format (Note that if DHCP is used,
Subnet mask and Gateway IP is not used by the ImagePRO.)
= xxx.xxx.xxx.xxx yyy.yyy.yyy.yyy zzz.zzz.zzz.zzz
Example:
EIP 192.168.000.200 255.255.255.000 192.168.000.001 (Sets IP address to 192.168.0.200, subnet
mask to 255.255.255.0, and default Gateway IP to 192.168.0.1)
EIP? (Returns IP address, subnet mask and Gateway IP)
Command:
EMAC?
Description:
Parameters:
Returns:
Query Ethernet MAC address for the ImagePRO. Note that each ImagePRO unit will have a
different MAC address.
None
MAC address. xx:xx:xx:xx:xx:xx
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
87
Example:
EMAC? (Queries for Ethernet MAC address)
Command:
SBAUD n
Description:
Adjust the Serial Baud Rate.
Parameters:
n - Serial baud rate: n[0-4] 1200 | 2400 | 9600 | 19200 | 38400
Query:
SBAUD?
Returns the Serial Baud Rate in the format
=n
Example:
SBAUD 0 (Adjusts Serial Baud Rate to 1200)
SBAUD? (Queries Serial Baud Rate.)
Command:
SYSAV
Description:
Parameters:
Example:
Saves the System State into non-volatile memory
None
SYSAV (Saves System State.)
Command:
HELP [op]
Description:
Parameters:
Example:
Displays Command List
op[A..Z] optional command
Help (Displays command list)
Help Freez (Displays syntax/parameters for the Freeze command)
Command:
LOADR
Description:
Parameters:
Example:
Places unit into loader mode. This mode is used to perform field upgrades
None.
LOADR
(Puts unit into loader mode.)
Command:
RESET
Description:
Parameters:
Example:
88
Factory resets the system and sets all settings to factory defaults.
None
RESET (Factory reset the ImagePRO)
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Logo Remote Commands
Command:
LOGOD
Description:
Parameters:
Example:
Delete Logo image from non-volatile memory. Selecting Black/Logo channel will now display black.
Logo feature only available on ImagePRO-SDI and ImagePRO-HD.
None
LOGOD (Delete saved Logo image.)
Command:
LOGOL
Description:
Parameters:
Example:
Load current output image from non-volatile memory as Logo image. Logo feature only available on
ImagePRO-SDI and ImagePRO-HD.
None
LOGOL (Load current output image as Logo image.)
Command:
LOGOS
Description:
Parameters:
Example:
Save current output image in non-volatile memory as Logo image. Logo feature only available on
ImagePRO-SDI and ImagePRO-HD.
None
LOGOS (Save current output image as Logo image.)
Command:
LOGOI
Description:
Parameters:
Example:
Query the stored Logo image resolution. Logo feature only available on ImagePRO-SDI and
ImagePRO-HD.
None
LOGOI (Query Logo resolution.)
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
89
Effects Remote Commands
Command:
TRN type in
Description:
Parameters:
Selects transition type when switching between inputs. Transition delay is only applicable if the
transition type selected is Fade to black / Fade to logo. Fade to logo transition type only available
on ImagePRO-SDI and ImagePRO-HD units, and is only selectable if Logo has been stored in nonvolatile memory.
type – Transition type [0-2] 0= Fade to black, 1=Freeze image and Cut, 2= Fade to logo
in – Transition delay (in seconds) [1.0s - 5.0s]
Query:
TRN?
Returns the current transition type and transition delay in the format
= type in
Example:
TRN 1 2.0 (Selects fade to black transition in 2 seconds.)
TRN? (Queries transition type and transition delay.)
90
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Pan / Zoom / View Remote Commands
Command:
PANH nnn.n
Description:
Set Output Horizontal Pan.
Parameters:
nnn.n - Horizontal Pan (-100.0% - +100.0%)
Query:
PANH?
Returns the Output Horizontal Pan value in the format
= nnn.n
Example:
PANH 50(Set Output Horizontal Pan to 50%)
PANH? (Queries Output Horizontal Pan)
Command:
PANHV hhh.h vvv.v
Description:
Parameters:
Set Output Diagonal Pan.
hhh.h - Horizontal Pan (-100.0% - +100.0%)
vvv.v - Vertical Pan (-100.0% - +100.0%)
Query:
PANHV?
Returns the Output Diagonal Pan value in the format
= hhh.h vvv.v
Example:
PANHV 50 50 (Set Output Horizontal Pan to 50%, and Vertical Pan to 50%)
PANHV?
(Query Output Horizontal Pan)
Command:
PANV nnn.n
Description:
Set Output Vertical Pan.
Parameters:
nnn.n - Vertical Pan (-100.0% - +100.0%)
Query:
PANV?
Returns the Output Vertical Pan value in the format
= nnn.n
Example:
PANV 50 (Set Output Vertical Pan to 50%)
PANV? (Queries Output Vertical Pan)
Command:
VIEW? nn
Description:
Parameters:
Returns:
Query saved View settings (i.e. Zoom setting, Pan H setting, Pan V setting)
nn – View Index [1 - 15]
nnn.n - Zoom value [min-max] depends on scale factor
hhh.h - Horizontal Pan (-100.0% - +100.0%)
vvv.v - Vertical Pan (-100.0% - +100.0%)
Command:
VIEWD nn
Description:
Parameters:
Example:
Delete saved View
nn – View Index [1 - 15]
VIEWD 1 (Delete View 1.)
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
91
Command:
VIEWR nn
Description:
Parameters:
Example:
Recall View
nn – View Index [0 - 15]. Index 0 is default view (i.e. Zoom = 100%, Pan H = 0%, Pan V = 0%)
VIEWR 1 (Recall saved View 1.)
Command:
VIEWS nn
Description:
Parameters:
Example:
Save current View to non-volatile memory
nn – View Index [1 - 15]
VIEWS 1 (Save current View to Index 1.)
Command:
VIEWI? in
Description:
Parameters:
Returns:
Example:
Query saved Input channel View settings (i.e. Zoom setting, Pan H setting, Pan V setting)
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
nnn.n - Zoom value [min-max] depends on scale factor
hhh.h - Horizontal Pan (-100.0% - +100.0%)
vvv.v - Vertical Pan (-100.0% - +100.0%)
VIEW? 1 (Query View settings for channel 1.)
Command:
VIEWIR
Description:
Parameters:
Example:
Recall currently routed Input channel’s View
None
VIEWR (Recall saved Input channel View for currently routed channel.)
Command:
VIEWIS in
Description:
Parameters:
Example:
Save current View to non-volatile memory for selected Input channel
in - Input chnl (1-4) chnl 4 only for ImagePRO-SDI and ImagePRO-HD units
VIEWIS 1 (Save current View for channel 1.)
Command:
ZOOM nnn.n
Description:
Selects zoom scale factor (applied both horizontally and vertically.
Parameters:
nnn.n - Zoom value [min-max] depends on scale factor
Query:
ZOOM?
Returns the current zoom scale factor in the format
= nnn.n
Example:
ZOOM 200.0
(Zoom into the image using a 200.0% scale factor)
ZOOM?
(Queries current zoom scale factor.)
92
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
93
5
CHAPTER FIVE
Software Upgrade Instructions
What you will find in this chapter…
‰
Software Upgrade Instructions
Model IP-2003
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
95
96
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Software Upgrade Instructions
Overview
The ImagePRO units incorporate the system software in a Flash memory component. Flash memory allows easy field
upgrades without the need to send the unit back to the factory.
The loader utility provides the capability to update the system Flash module with the latest revision of software. The
upgrade utility can be run from a hard drive (recommended) or a floppy drive. Running the loader from a floppy drive
is discouraged though due to the slow speeds associated with disk access.
Hardware Requirements
* IBM compatible computer with an available COM port
* Serial cable conforming to EIA RS-232 specifications (i.e. Standard Modem cable)
(The cable should have a DB-9 male connector on one end)
Software Requirements
* Windows NT/2000/XP
* Flash File Loader
* ImagePRO Software files
The Flash File Loader with the Software files can be downloaded from our FTP site as described below.
Connecting to Folsom Research
Folsom Research's FTP site address is: ftp.folsom.com
If you are using an FTP client, logon to our site using "anonymous" for the user
name and your email address as the password (ex. johndoe@somecompany.com).
However, if you are using a web browser to access our FTP site, point the browser to: ftp://ftp.folsom.com.
Downloading Necessary Files
ImagePRO Software Files and Flash File Loader
Directory Location: ftp://ftp.folsom.com\ Products \ Video \ IP2003 \
File to download: "ImagePro_Rev#####_###.exe"
Installing ImagePRO’s Software Files and Flash File Loader
Before installing the files, it is recommended that all running programs be properly shut down.
1.
2.
3.
4.
Click on the Start button and select Run.
Click on the Browse button and locate the "ImagePro_Rev#####_###.exe" file on your hard drive.
Double click on this file and then click OK to start the installation process.
Follow the on screen instructions to complete the install.
Starting the ImagePRO Flash File Loader Utility
After the files have been installed the ImagePRO Flash File Loader can be selected to run.
1. Click on the Start button and select Programs.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
97
2.
Find the Folsom Research folder and select ImagePRO Flash File Loader.
Preparing to Upgrade the ImagePRO Unit
1.
Plug the DB-9 male connector into the port labeled “RS-232 on the back of the ImagePRO unit.
2.
Make sure the other end of the cable is attached to the available COM port on the back of the computer
performing the upgrade.
3.
In the loader program, click on the RS232 Config menu and select COM Port.
4.
In the Communication Settings window, select the COM port the ImagePRO Remote port is attached to by
clicking on the appropriate COM # choice.
5.
The ImagePRO Remote port defaults to a baud rate of 38400 baud (38.4K).
Uploading Files to the ImagePRO Unit
98
1.
Once communications have been established and verified, click on the “Open script file to read and upload”
button to begin the upgrade process.
2.
Browse to the location where the “CompleteLoad.sld” file is located and click on it. Then click on “Open” to
start transferring the files to the ImagePRO.
3.
A TRANSFER STATUS box will open and show the status of the upload as it progresses.
4.
After a few minutes, the loader utility will inform the user that the process is complete.
5.
Once this is done, it is recommended that the entire system be powered cycled. You can also close the
loader utility at this time.
6.
Verify the new software is in the system by looking for the version number in the SetupÆTech Support
menu.
7.
Once you have verified the version number, it is recommended that a factory reset be performed. This is
done by going to the Setup Menu and selecting Factory Reset.
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
6
CHAPTER SIX
Barco Folsom Information
What you will find in this chapter…
‰
Warranty
‰
RMA Information
‰
Technical Support/General Contact Information
Model IP-2003
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
99
100
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Barco Folsom Information
Barco Folsom Warranty
All video products are designed and tested to the highest quality standards and are backed by a full 3-year parts and
labor warranty. Warranties are effective upon delivery date to customer and are non-transferable. Folsom Research,
Inc. warranties are only valid to the original purchaser/owner. Warranty related repairs include parts and labor, but do
not include faults resulting from user negligence, special modifications, lightning strikes, abuse (drop/crush), and/or
other unusual damages.
The customer shall pay shipping charges when unit is returned for repair. Barco Folsom will cover shipping charges
for return shipments to customers.
Return Material Authorization (RMA)
In the unlikely event that a product is required to return for repair, please call 888-414-7226 and ask for a Sales
Engineer to receive a Return Merchandise Authorization number (RMA).
RMA Conditions:
a) Prior to returning any item, you must receive a Return Merchandise Authorization (RMA) number.
b) All RMA numbers must appear on their return-shipping label.
c) RMA numbers are valid for ten (10) days from issue date.
d) All shipping and insurance charges on all RMA's must be prepaid by the customer
Barco Folsom Contact Information
Sales Contact Information
Direct Sales Line: 916-859-2505
Toll Free Line: 888-414-7226
E-mail: sales@folsom.com
Technical Support Information
Tech Line: 866-374-7878 (24hours/7days)
E-mail: support@folsom.com
General Company Information
Barco Folsom, LLC
11101 Trade Center Drive
Rancho Cordova, CA 95670
Toll Free: 888-414-7226
Tel: 916-859-2500
Fax: 916-859-2515
Web Address: www.folsom.com
Barco Folsom Europe
Barco N.V.
Noordlaan 5
B-8520 Kuurne
Belgium
T: +32 56 368798
F: +32 56 368824
Hours of operation are Monday through Friday 0900 to 1800 (GMT)
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
101
102
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
A
APPENDIX
‰
Technical Specifications
Model IP-2003
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
103
104
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
Technical Specifications
Video Input
Inputs:
Universal Inputs: (3) high bandwidth video channels support, RGBHV/RGBS/RGsB computer video, component video
(STD or HDTV), S-video, or Composite video
Connectors: Input 1 and 2 on 15-pin HD connectors with buffered loop-through. Input 3 on five BNC connectors with
buffered loop-through. On ImagePRO-HD input 1 on DVI-I connectors.
Serial Digital Video Input: (1) SDI input on ImagePRO-SDI model, or SDI/HDSDI input on ImagePRO-HD
Connectors: BNC
Digital Video (DVI) Input: (1) Input on DVI-I connector supports both universal analog and DVI input with loop-through
Input Resolution Range: VGA (640x480), SVGA(800x600), XGA(1024x768), SXGA(1280x1024), UXGA(1600x1200),
HDTV 480p, 720p, 1080p, 1080i, 875 RS-343, 525 RS-170
Standard Resolution Video Input: NTSC, PAL or SECAM
Horizontal Frequency: 15 kHz to 120 kHz
Vertical Frequency: 25 Hz to 120 Hz
Input Termination: 75 Ohm
Input Sync: Sync-on-Video, Separate C or H/V
External Sync (Genlock) Input: Blackburst, Computer H/V Sync or C-sync.
Connectors: BNC
Video Output
Outputs:
RGB or component video (STD or HDTV) on HD-15, RGB or component video (STD or HDTV) or composite video on
BNC, S-video on 4-pin mini-DIN connector
SDI on BNC, ImagePRO with SDI and ImagePRO-HD models only, or SDI/HDSDI input on ImagePRO-HD
DVI output on DVI-D connector on ImagePRO-HD model only
Standard resolution video output: NTSC, PAL
High resolution output supported: VGA (640x480), SVGA(800x600), XGA(1024x768), SXGA(1280x1024),
UXGA(1600x1200). For Plasma Displays 1280x768, 1365x768, 1365x1024. HDTV 480p, 720p,
1080p, 1080i. 875 RS-343, 525 RS-170
Sync: RGBHV, RGBS, RGsB, TTL level, Polarity selectable, HDTV, Tri-level Sync supported
75 ohm Output Impedance
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
105
User Control
Local: User-friendly front panel interface
Ethernet connection (with TCP/IP) or RS-232 serial port for real-time control
Physical
Height: 1.5"; Width: 17" (43.2 cm) or 19" (48.3 cm) with rack-mount option;
Depth: 13"; Weight: 9lbs. ; Shipping Weight: 13 lbs.
Input Power
100-240 VAC, 47-63 Hz
Environmental
Temperature: 0-40 degrees C; Humidity: 0-95% non-condensing.
Warranty
All video products are designed and tested to the highest quality standards
and are backed by a full three-year parts and labor warranty.
106
ImagePRO – Multi Format Image Processor
Manual # 26-0302000-00 / Revision E
FCC Classification
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user
will be required to correct the interference at the users own expense.
Manual # 26-0302000-00 / Revision E
ImagePRO – Multi Format Image Processor
107
Download PDF