ACROSSER

ACROSSER
AR-ES0631ET Installation Guide
ACROSSER®
AR-ES0631ET (Extended Temperature)
powered by AMD Geode LX800, EPIC SBC with
CRT, LCD, LAN, USB2.0, PCI/104
Installation Guide
Edition: 1.0
1
AR-ES0631ET Installation Guide
Contents
1
2
Introduction of AR-ES0631ET………..……………………………… 3
1.1 Product Outlines
4
1.2 Packing List
5
Procedure of Assembly/Disassembly cables from the board…….. 6
2-1 Installing the 2.5”Hard Disk Drive(HDD)………………………... 6
2-2 Installing an memory card to AR-ES0631……………………… 8
2-3 Inserting a Compact Flash Card………………………………… 12
Appendix…………………………………
14
LVDS connector pin assignment…………………………………….. 14
Power connector pin assignment……………………………………. 15
COM1 to COM4 connector pin assignment………………………… 15
2
AR-ES0631ET Installation Guide
1. Introduction of AR-ES0631ET
Welcome to the AR-ES0631ET wide-range temperature product, in which a Single Board
Computer with low power AMD Geode LX800 processor designed-in. The system is
designed for extreme environment with of operating range from -40℃ to +75℃. For this
product feature, AR-ES0631ET can make a lot of outdoor applications available, such as
Traffic Control, Vehicle Computer, Remote Workstation, Outdoor Data Acquisition,
Aviation or Military industries.
ACROSSER’s Extended temperature products are almost choosing the wide operating
temperature components (compliance with Industrial standard in operating temperature)
onboard. This platform has fully loaded and pass robust thermal cycling tested. It is a
reliable, long life time and cost effective extended temperature solution for diverse
applications.
In addition, the AR-ES0631ET provides on chip VGA. The VGA, which provides up to
1920x1440x32bpp at 85Hz and 1600x1200x32bpp at 100HZ resolutions. The VGA
memory is shared with the main memory (2M, 4M, or 8M). AR-ES0631ET also has
18-bit LVDS function in the system, which the resolution up to 1600x1200x32bpp at
60Hz.
The AR-ES01631ET is loaded with special on-board features that rival full-size systems.
It has one network controller on board, uses Realtek RTL8100BL LAN controller, a fully
integrated 10/100BASE-TX solution with high performance networking functions.
Supports Compact Flash™ Type II interface. Plus optional support for AC97 sound with
CD-input. The AR-ES0631ET also includes one 200-pin SO-DIMM DDR sockets for up
to 1GB total on-board memory. The AR-ES0631ET has four on-board serial ports; COM1
with RS232C, COM2, COM3 and COM4 with RS232C, 4 USB ports, and tough
industrial grade construction. All these features make the AR-ES0631ET a very "system
integrator friendly" solution, perfect for handling applications in the harshest unmanned
environments.
3
AR-ES0631ET Installation Guide
1.1 Product Outlines
Description
AR-ES0631ET Serial
CPU Board
AR-B1631ET series
Dimensions
250×117×59 (mm)
AR-ES1631ET product outlines
4
AR-ES0631ET Installation Guide
1.2 Packing List
Description
Q’ty
AR-ES0631ET
1
Power Core/ Adapter
1
IDE Cable
1
Others Screws
4
Mounting Bracket (+screw)
2
5
AR-ES0631ET Installation Guide
2. Procedure of Assembly/Disassembly
2-1 Installing the 2.5”Hard Disk Drive (HDD)
The following are step-by-step installation
1. Insert the anti-vibration rubbers into the four edge of HDD bracket bay
2. Connect the IDE cable to the 44-pin header of HDD
3. Put the HDD on the HDD bracket and screw them together via four
screws
4. Remove the CPU board out from the AR-ES0631ET for installing the HDD
module later
Fig.1 HDD bracket bay
5. Remove the back cover of AR-ES0631ET by unlocking the two screws
Unlock the
screws
Fig.2 Back cover
6
AR-ES0631ET Installation Guide
6. Place the HDD module into the space as shown in Fig. 3 and assemble
them together with the case via the fire screws
Fig 3 Install HDD module into AR-ES0631ET
7
AR-ES0631ET Installation Guide
2-2 Installing an memory card to AR-ES0631ET
The following are step-by-step installation
1.
Remove the power cord out from the AR-ES0631ET
2.
Unlock the four screws on the top case of AR-ES0631ET, as shown in
Fig.4
Fig. 4 Unlock the top case
3.
Unlock the four screws from the front panel and back panel as shown in
Fig.5
Fig.5 Unlock screws from the front/rear panel
8
AR-ES0631ET Installation Guide
4.
Remove the IDE cable out front the CPU board (if you had a HDD
module installed)
5.
Unlock the four screws of CPU board out from the AR-ES0631ET as
shown in Fig. 6
Fig.6 Remove the HDD cable out from the CPU board
6.
Remove the CPU board out from the AR-ES0631ET as shown in Fig. 7
Fig. 7 Remove the CPU board
9
AR-ES0631ET Installation Guide
7.
Plug the memory card into the socket as shown in Fig. 8
Memory card
Fig.8 Install the memory card into the memory socket
8.
Put the CPU board back and screw it on the AR-ES0631ET bottom case
as shown in Fig. 9
Fig.9 Back CPU board into the AR-ES0631ET
10
AR-ES0631ET Installation Guide
9.
Re-connect the IDE cable to CPU board as shown in Fig. 10
Fig. 10 Re-connect IDE cable to the CPU board
10.
Back the top cover to the AR-ES0631ET and tight-up with four screws
Fig. 15 back the top cover
11. Tight the four screws on front panel and back panel as shown in Fig.11
Fig. 11 Tight the screw on the front panel
11
AR-ES0631ET Installation Guide
2-3 Installing a Compact Flash Card
The following are step-by-step installation
1. Remove the power Cord out from the AR-ES0631ET
2. Unlock the two screws from the CF door located on the front panel of
AR-ES0631ET as shown in Fig. 12
Fig.12 Unlock the screw from the CF door
3. Remove the CF holder
4. Place a Compact Flash card with OS or application program inside into
the CF holder as shown in Fig. 13
Fig.13 Inset the CF card into the CF holder
12
AR-ES0631ET Installation Guide
5. Back the CF module to the CF door and lock the CF door with 2 screws to
the front panel as shown in Fig 14
Fig. 14 Back the CF module to AR-ES0631ET
13
AR-ES0631ET Installation Guide
Appendix
LVDS connector pin assignment
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
LVDS connector Pin Assignment
Pin
Description
Description
14
CLKVCC
15
CLK+
VCC
16
GND
NC
17
NC
NC
18
NC
Y019
NC
Y0+
20
VCC12
GND
21
VCC12
Y122
GND
Y1+
23
BKLEN
GND
24
GND
Y225
BKLTCTL
Y2+
GND
14
AR-ES0631ET Installation Guide
Power connector pin assignment
Pin
1
2
LVDS connector Pin Assignment
Description
Pin
Description
12V
3
GND
12V
4
GND
COM1 to COM4 connector pin assignment
COM1 to COM4 connector pin assignment
Pin
Description
Pin
Description
NDCD
NRX
1
6
NTX
NDTR
2
7
GND
NDSR
3
8
NRTS
NCTS
4
9
NRIA_12V
NC
5
10
* NRIA_12V: Please see AR-B1631 manual for detail data.
15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement