T-Series Sensor Data Sheet

Product Data Sheet
PS-00371, Rev. I
August 2015
Micro Motion® T-Series
Coriolis Flow and Density Meters
Micro Motion® T-Series meters offer the best performance of any straighttube Coriolis meter. The single straight-tube design is self-draining, and
allows the meter to be cleaned or sterilized in place (CIP/SIP). The straight
flow path also resists plugging, and can be pigged.
ELITE®
ELITE HC
Peak performance
high capacity
meter
F-Series
High performance
compact drainable
Coriolis meter
H-Series
Hygienic compact
drainable Coriolis
meter
Superior flow measurement in a single straight tube flow meter
•
Built-in balance bar provides the best single straight tube mass flow
measurement to reduce variability in process control
Comprehensive hygienic application coverage
•
Easy to CIP and SIP with EHEDG certified, 3-A authorized,
ASME BPE design
•
Diameter matches standard process tubing for draining in any
orientation
•
Fast product change-over with self-draining design and no profile
effects
•
Single flow path is easy to clean mechanically
•
Highly-polished surface finish for ultra-pure fluids
Superior reliability
•
Peak
performance
Coriolis meter
No moving parts to wear or replace minimizes maintenance for
long-term reliability
T-Series
R-Series
LF-Series
Straight tube
full-bore
Coriolis meter
General purpose
flow-only
Coriolis meter
Extreme lowflow Coriolis
meter
Micro Motion T-Series straight-tube flow and density meters
Micro Motion Coriolis meters meet a vast range of application needs, ranging from extreme low-flow up to
high-flow, high-capacity lines. Cryogenic, hygienic, high-temperature, and high-pressure— Micro Motion
meters can handle them all. Micro Motion meters are available with a variety of wetted parts to ensure the
best material compatibility.
Coriolis meters. Coriolis meters offer dramatic
benefits over traditional volumetric measurement
technologies. Coriolis meters:
•
Deliver accurate and repeatable process data
over a wide range of flow rates and process
conditions.
•
Provide direct inline measurement of mass flow
and density, and also measure volume flow and
temperature—all from a single device.
•
Have no moving parts, so maintenance costs
are minimal.
•
Have no requirements for flow conditioning or
straight pipe runs, so installation is simplified
and less expensive.
•
Provide advanced diagnostic tools for both the
meter and the process.
T-Series Coriolis meters. Our straighttube meter design is based on the ASME
Bioprocessing Equipment Standard. With
optional sanitary fittings, Micro Motion
T-Series meters meet 3-A Sanitary
Standards for Milk and Milk Products, are
EHEDG clean-in-place approved, and
feature a standard surface finish of
32 µ-inch Ra (0.8 µ-meter)—and
15 µ-inch Ra (0.38 µ-meter) is an available option.
TYPE
EL
JANUARY 2002
The Micro Motion T-Series single straight-tube
design makes these meters self-draining, and
allows them to be cleaned or sterilized in place
(CIP/SIP). The straight flow path also resists
plugging, and can be pigged.
Contents
Flow performance . . . . . . . . . . . . . . . . . . . . . . . . . 3
Density performance (liquid only) . . . . . . . . . . . . . 4
Temperature specifications . . . . . . . . . . . . . . . . . . 5
Pressure ratings . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Environmental effects . . . . . . . . . . . . . . . . . . . . . 11
Vibration limits . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Sanitary standards . . . . . . . . . . . . . . . . . . . . . . . 11
2
T-Series Straight-Tube Coriolis Flow and Density Meters
Meter approvals and certifications. . . . . . . . . . . .
Materials of construction . . . . . . . . . . . . . . . . . . .
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fitting options . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ordering information . . . . . . . . . . . . . . . . . . . . . .
12
12
13
14
17
25
Flow performance
Maximum flow rate
T025
T050
T075
T100
T150
Mass flow accuracy (2)
±0.15% of rate (3)
Volume flow accuracy (2)
±0.25% of rate (4)
Gas flow accuracy (2)
±0.50% of rate (5)
Repeatability
±0.05% of rate
Zero stability
T025
T050
T075
T100
T150
kg/h
Volume (1)
gal/min
l/h
25
140
500
1100
3200
680
3800
14,000
30,000
87,000
3
17
62
132
383
680
3800
14,000
30,000
87,000
lb/min
kg/h
gal/min
l/h
0.0038
0.021
0.075
0.165
0.48
0.10
0.57
2.0
4.50
13.0
0.0005
0.0025
0.009
0.02
0.06
0.10
0.57
2.0
4.50
13.0
Mass
lb/min
(1) Specifications for volumetric flow rate are based on a process-fluid density of 1 g/cc (1000 kg/m3). For fluids with density other than
1 g/cc (1000 kg/m3), the volumetric flow rate equals the maximum mass flow rate divided by the fluid’s density.
(2) Flow accuracy includes the combined effects of repeatability, linearity, and hysteresis. All specifications for liquids are based on
reference conditions of water at 68 to 77 °F (20 to 25 °C) and 15 to 30 psig (1 to 2 bar), unless otherwise noted.
(3) When flow rate < (zero stability / 0.0015), then mass flow accuracy = ±[(zero stability / flow rate) × 100]% of rate and
repeatability = ±[½(zero stability / flow rate) × 100]% of rate.
(4) When flow rate < (zero stability / 0.0025), then volume flow accuracy = ±[1.667 × (zero stability / flow rate) × 100]% of rate, and
repeatability = ±[½(zero stability / flow rate) × 100]% of rate.
(5) When flow rate < (zero stability / 0.005), then gas flow accuracy = ±[(zero stability / flow rate) × 100]% of rate, and
repeatability = ±[½(zero stability / flow rate) × 100]% of rate.
T-Series Straight-Tube Coriolis Flow and Density Meters
3
Flow performance continued
Typical accuracy, turndown, and pressure drop
Pressure drop is dependent on process conditions. To determine accuracy, turndown, and pressure drop with your process
variables, use Micro Motion’s product selector, available at www.micromotion.com.
2.5
100:1
2.0
1:1
20:1
10:1
1.5
Accuracy (%)
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
–2.5
0
10
20
30
40
50
60
70
80
90
100
Maximum flow rate (%)
Turndown from maximum
flow rate
100:1
20:1
10:1
1:1
Accuracy (± %)
1.60
0.31
0.15
0.15
Pressure drop
psi
bar
~0
0.06
0.22
14.3
~0
0.02
0.05
0.99
Density performance (liquid only)
Accuracy (1)
±0.002 g/cc
±2.0 kg/m3
Repeatability
±0.0005 g/cc
±0.5 kg/m3
0–5000 kg/m3
Range
(1) Density accuracy includes the combined effects of repeatability, linearity, and hysteresis. All specifications for liquids are based on
reference conditions of water at 68 to 77 °F (20 to 25 °C) and 15 to 30 psig (1 to 2 bar), unless otherwise noted.
4
T-Series Straight-Tube Coriolis Flow and Density Meters
Temperature specifications
±1.0 °C ±0.5% of reading in °C
Repeatability
±0.2 °C
Mount transmitter remotely; use junction box
125.5
(52)
140 (60)
122
(50)
100 (38)
60 (16)
20 (7)
Below –40 °F (–40 °C),
mount transmitter remotely;
use junction box
–20 (–29)
–40 (–40)
300 (149)
320 (160)
280 (138)
240 (116)
200 (93)
140 (60)
100 (38)
60 (16)
20 (7)
–20 (–29)
–60 (–51)
–60 (–51)
Temperature limits (1) (2) (3)
Ambient temperature of core processor or transmitter in °F (°C)
Accuracy
Maximum process temperature in °F (°C)
(1) Temperature limits may be further restricted by hazardous area approvals. See page 12.
(2) When ambient temperature is below –40 °F (–40 °C), a core processor must be heated to bring its local ambient temperature to
between –40 °F (–40 °C) and +140 °F (+60 °C). Long-term storage of electronics at ambient temperatures below –40 °F (–40 °C) is not
recommended.
(3) For the purposes of selecting electronics options, this graph should be used only as a general guide. If your process conditions are
close to the gray areas, it may be inappropriate to use electronics options other than a junction box. Consult with your Micro Motion
representative.
T-Series Straight-Tube Coriolis Flow and Density Meters
5
Pressure ratings
All pressure ratings are based on ASME B31.3.
PED compliance
Sensors comply with council directive 97/23/EC of 29 May 1997 on Pressure Equipment.
Models without purge fittings
Models with purge fittings
ASME B31.3 secondary
containment rating (1)
psig
bar
1450
725
100
50
(1) Housing is not rated for pressure containment below –20 °F (–29 °C).
Sensor pressure/temperature rating with ASME B16.5 F316/316L socket weld flanges
Models T025T through T150T; Models T075F through T150F
Pressure (psig)
Temperature (°F)
6
T-Series Straight-Tube Coriolis Flow and Density Meters
Pressure ratings continued
Sensor pressure/temperature rating with Tri-Clamp compatible
Ti Grade 1/304L clad hygienic fittings
Models T025T through T150T; Models T025F through T150F
Pressure (psig)
Temperature (°F)
Sensor pressure/temperature rating with VCO Ti Grade 1/304L clad fittings
Models T025T and T050T
Pressure (psig)
Temperature (°F)
T-Series Straight-Tube Coriolis Flow and Density Meters
7
Pressure ratings continued
Sensor pressure/temperature rating with JIS 2220 F316/316L socket weld flanges
Models T025T through T150T; Models T075F through T150F
Pressure (bar)
Temperature (°C)
Sensor pressure/temperature rating with DIN 11851 Ti Grade 1/304L clad hygienic coupling
Models T025T through T150T; Models T025F through T150F
Pressure (bar)
Temperature (°C)
8
T-Series Straight-Tube Coriolis Flow and Density Meters
Pressure ratings continued
Sensor pressure/temperature rating with DIN 11864-1 Ti Grade 1/304L clad hygienic coupling
Models T025T through T150T; Models T025F through T150F
Pressure (bar)
Temperature (°C)
Sensor pressure/temperature rating with SMS 1145 316L hygienic coupling
Models T075T, T150T, T075F, and T150F
Pressure (bar)
Temperature (°C)
T-Series Straight-Tube Coriolis Flow and Density Meters
9
Pressure ratings continued
Sensor pressure/temperature rating with ISO 2853 (IDF) 316L process fittings
Models T075T, T150T, T075F, and T150F
Pressure (bar)
Temperature (°C)
Sensor pressure/temperature rating with EN1092-1 & DIN F316/316L socket weld flanges
Models T025T through T150T; Models T075F through T150F
Pressure (bar)
Temperature (°C)
10
T-Series Straight-Tube Coriolis Flow and Density Meters
Environmental effects
Process temperature effect
Process temperature effect is defined as the worst-case zero offset due to process fluid
temperature change away from the zeroing temperature.
All models
Pressure effect
0.002% of maximum flow rate per °C
Pressure effect is defined as the change in sensor flow sensitivity due to process pressure
change away from the calibration pressure. Pressure effect can be corrected.
All models
None
Vibration limits
Meets IEC 68.2.6, endurance sweep, 5 to 2000 Hz, 50 sweep cycles at 1.0 g
Sanitary standards
For sanitary applications, Micro Motion T-Series sensors with sanitary fittings feature a standard 32 µ-inch Ra (0.8 µ-meter) tube
surface finish, with 15 µ-inch Ra (0.38 µ-meter) surface finish available as an option.
ASME
The Micro Motion T-Series sensor design is based on the ASME Bioprocessing Equipment
Standard – 1997. With sanitary fittings, these sensors meet the ASME Bioprocessing
Equipment Standard.
3-A
Micro Motion T-Series sensors with sanitary fittings meet 3-A Sanitary Standards for Milk
and Dairy Products.
USDA
Micro Motion T-Series sensors with sanitary fittings are acceptable for use in dairy plants
and are approved for USDA grading service.
EHEDG
Micro Motion T-Series sensors with sanitary fittings are approved by the European Hygienic
Equipment Design Group. Sensors comply with the hygienic criteria of Machinery Directive
98/37/EC, annex 1 (additional essential health and safety requirements for certain
categories of machinery), section 2.1 (agri-foodstuffs machinery). Test results show that
Micro Motion T-Series sensors can be cleaned in place at least as well as the reference pipe.
T-Series Straight-Tube Coriolis Flow and Density Meters
11
Meter approvals and certifications
Type
CSA and CSA C-US
ATEX
IECEx
Ingress protection rating
EMC effects
Approval or certification (typical)
Ambient temperature: –40 to +140°F (–40 to +60°C)
Class I, Div. 1, Groups C and D.
Class I, Div. 2, Groups A, B, C, and D.
II 2G Ex ib IIB/IIC T1–T4/T5/T6 Gb
0575
II 2D Ex ib IIIC T(1)°C Db IP66
II 3G Ex nA IIC T1–T4/T5 Gc
II 3D Ex tc IIIC T(1) °C Dc IP66
Ex ib IIB/IIC T1–T4/T5/T6 Gb
Ex nA IIC T1-T4/T5 Gc
IP66 for sensors; IP 66/67 for transmitters
Complies with EMC directive 2004/108/EC per EN 61326 Industrial
Complies with NAMUR NE-21 (09.05.2012)
•
Approvals shown are for T-Series meters configured with a model 2400S transmitter. Meters with integral
electronics may have more restrictive approvals. Refer to the product data sheet for each transmitter for
details.
•
When a meter is ordered with hazardous area approvals, detailed information is shipped along with the
product.
•
You can find more information about hazardous approvals, including detailed specifications and
temperature graphs for all meter configurations on the T-Series product page at the Micro Motion web
site (www.micromotion.com).
Materials of construction
Wetted parts (1)
Flow tubes
Sanitary fittings (2)
Socket-weld flanges (2)
Titanium ASTM Grade 9
304L stainless steel and titanium ASTM Grade 1
F316/316L stainless steel and titanium ASTM Grade 5 (6AL-4V)
Sensor housing
Sensor
304L stainless steel
Core processor
316L stainless steel or polyurethane-coated aluminum;
NEMA 4X (IP66)
Polyurethane-coated aluminum; NEMA 4X (IP66)
Junction box
(1) General corrosion guides do not account for cyclical stress, and therefore should not be relied upon when choosing a wetted material
for your Micro Motion sensor. Please refer to Micro Motion’s corrosion guide for material compatibility information.
(2) Flanges are stainless steel; wetted parts are titanium. Only titanium is in contact with process flow.
12
T-Series Straight-Tube Coriolis Flow and Density Meters
Weight
Approximate weight with ANSI CL150 socket weld raised face flange
Sensor with core processor (1)
Sensor with extended core processor (1)
Sensor with integrally mounted
Model 1700/2700 transmitter
Sensor with junction box
Sensor with extended junction box
T025
lb
kg
T050
lb
kg
T075
lb
kg
T100
lb
kg
T150
lb
kg
14
15
20
7
7
9
16
17
22
7
8
10
33
34
39
15
16
18
58
59
64
27
27
29
137
138
143
63
63
65
–
–
–
–
–
–
–
–
32
33
15
15
57
58
26
27
136
137
62
63
Approximate weight with 1/2-inch or 1-inch sanitary fitting (Tri-Clamp compatible)
Sensor with core processor (1)
Sensor with extended core processor (1)
Sensor with integrally mounted
Model 1700/2700 transmitter
Sensor with junction box
Sensor with extended junction box
T025
lb
kg
T050
lb
kg
T075
lb
kg
T100
lb
kg
T150
lb
kg
12
13
18
6
6
8
14
15
20
7
7
9
33
34
39
15
16
18
55
56
60
25
25
28
131
132
137
60
60
62
–
–
–
–
–
–
–
–
32
33
15
15
54
55
25
25
130
131
59
60
(1) Add 4 lbs (2 kg) for stainless steel core processor housing option (electronics interface codes A, B, D, and E).
T-Series Straight-Tube Coriolis Flow and Density Meters
13
Dimensions
Sensor with core processor
Dimensions in
inches
(mm)
Optional 2 × 1/2”–14 NPT
female purge connection
with male hex plug
Extended mount option
Ø4 3/8
(111)
1/2”–14 NPT
or M20 × 1.5
female
2 5/8
(67)
Dim. P
Dim. Q
Ø1 1/4
(32)
5.66
(144)
Dim. M
Dim. N
Dim. ØC
Dim. ØB
Dim. R
Dim. E
Dim. A
±1/8” (3 mm)
Dimensions in inches (mm) (1)
Sensor model
No. of
flow tubes Tube ID
ØC (case
diameter)
E
M
N
P
Q
R
T025
1
T050
1
T075
1
T100
1
T150
1
3 1/8
(79)
3 1/8
(79)
4 1/8
(105)
5 1/8
(130)
7 1/8
(181)
4 1/8
(105)
5 1/2
(140)
6 1/8
(156)
11
(279)
11
(279)
5 1/4
(133)
5 1/4
(133)
5 3/4
(147)
6 1/4
(159)
7 1/4
(185)
3 1/2
(89)
3 1/2
(89)
4 1/16
(103)
4 9/16
(116)
5 9/16
(141)
10 5/8
(269)
10 5/8
(269)
11 1/8
(283)
11 5/8
(296)
12 5/8
(321)
8.88
(225)
8.88
(225)
9.44
(240)
9.94
(252)
10.94
(278)
2 11/16
(68)
2 11/16
(68)
3 3/16
(81)
3 11/16
(93)
4 11/16
(119)
0.180
(4.57)
0.360
(9.14)
0.619
(15.72)
0.870
(22.10)
1.360
(34.54)
(1) For dimensions A and B, see process fittings tables, pages 17–24.
14
T-Series Straight-Tube Coriolis Flow and Density Meters
Dimensions continued
Sensor with integrally mounted Model 1700/2700 transmitter
Dimensions in
inches
(mm)
6 13/16
(174)
2 × 1/2”–14 NPT or
M20 × 1.5 female
Ø4 11/16
(119)
2.69
(68)
Optional 2 × 1/2”–14 NPT
female purge connection
with male hex plug
Dim. F
Dim. N
Dim. ØC
Dim. ØB
Dim. R
Dim. E
Dim. A
±1/8” (3 mm)
THUM adapter detail
2.0
(51)
7.27
(185)
1/2”–14 NPT female
Dimensions in inches (mm) (1)
Sensor
model
No. of
flow tubes
Tube ID
ØC (case
diameter)
E
F
N
R
T025
T050
T075
T100
T150
1
1
1
1
1
0.180 (4.57)
0.360 (9.14)
0.619 (15.72)
0.870 (22.10)
1.360 (34.54)
3 1/8 (79)
3 1/8 (79)
4 1/8 (105)
5 1/8 (130)
7 1/8 (181)
4 1/8 (105)
5 1/2 (140)
6 1/8 (156)
11 (279)
11 (279)
9 3/16 (233)
9 3/16 (233)
9 3/4 (247)
10 1/4 (260)
11 1/4 (285)
5.5 (139)
5.5 (139)
6.03 (153)
6.54 (166)
7.53 (191)
2 11/16 (68)
2 11/16 (68)
3 3/16 (81)
3 11/16 (93)
4 11/16 (119)
(1) For dimensions A and B, see process fittings tables, pages 17–24.
T-Series Straight-Tube Coriolis Flow and Density Meters
15
Dimensions continued
Sensor with junction box
Dimensions in
inches
(mm)
Extended
mount option
Optional 2 × 1/2”–14
NPT female purge
connection with male
hex plug
3 3/4
(95)
3/4”–14 NPT
female
3 1/2
(89)
Ø1 1/4
(32)
Dim. Q
Dim. H
5.66
(144)
Dim. F
Dim. N
Dim. ØC
Dim. ØB
Dim. R
Dim. E
Dim. A
±1/8” (3 mm)
Dimensions in inches (mm) (2)
Sensor
model (1)
No. of
flow tubes Tube ID
ØC (case
diameter)
E
F
H
J
N
Q
R
T075
1
T100
1
T150
1
4 1/8
(105)
5 1/8
(130)
7 1/8
(181)
6 1/8
(156)
11
(279)
11
(279)
4 1/2
(114)
5
(127)
6
(152)
9 7/8
(251)
10 3/8
(264)
11 3/8
(289)
8 9/16
(217)
9 1/16
(230)
10 1/16
(256)
3.19
(81)
3.69
(94)
4.69
(119)
8.56
(217)
9.06
(230)
10.06
(256)
3 3/16
(81)
3 11/16
(93)
4 11/16
(119)
0.619
(15.72)
0.870
(22.10)
1.360
(34.54)
(1) Models T025 and T050 are not available with junction box.
(2) For dimensions A and B, see process fittings tables, pages 17–24.
16
T-Series Straight-Tube Coriolis Flow and Density Meters
Fitting options
Fittings listed here are standard options. Other types of fittings are available. The face to face dimensions for any custom fittings
ordered using a 998 or 999 fitting code are not represented in this table. It is necessary to confirm face to face dimensions of these
fittings at time of ordering. Contact your local Micro Motion representative.
Model T025T
Code
525
526
613
Description
DN15
PN40 EN 1092-1
DN15
PN100 EN 1092-1
1/2-inch CL150 ASME B16.5
614
1/2-inch
CL300
ASME B16.5
615
1/2-inch
CL600
ASME B16.5
616
DN15
PN40
DIN 2526
617
DN15
PN100 DIN 2526
621
1/2-inch
636
#8
Tri-Clamp
compatible
VCO
637
#8
VCO
650
DN15
PN40
DIN 2512
654
670
DN15
DN10
PN40
EN 1092-1
DIN11851
671
DN15
676
DN15
781
15mm
20K
Form B1
Form B2
Raised face
Dim. A
13.65 (347)
13.97 (355)
13.31 (338)
Dim. B
3 3/4 (95)
4 1/8 (105)
3 1/2 (89)
Raised face
13.83 (351)
3 3/4 (95)
Raised face
13.95 (351)
3 3/4 (95)
Type C face
13.65 (347)
3 3/4 (95)
Type E face
13.97 (355)
4 1/8 (105)
13.92 (354)
1 (25)
18.67 (474)
—
15.13 (384)
—
13.65 (347)
3 3/4 (95)
13.65 (347)
13.93 (354)
3 3/4 (95)
Rd 28 × 1/8
13.93 (354)
Rd 34 × 1/8
13.89 (353)
Rd 34 × 1/8
13.64 (346)
3 3/4 (95)
Dim. A
13.92 (354)
Dim. B
1 (25)
Hygienic
coupling
Hygienic
coupling
13.93 (354)
Rd 28 × 1/8
13.93 (354)
Rd 34 × 1/8
13.89 (353)
Rd 34 × 1/8
F316/F316L
F316/F316L
F316/F316L
Weld neck flange
Weld neck flange
Socket weld
flange
F316/F316L
Socket weld
flange
F316/F316L
Socket weld
flange
F316/F316L
Socket weld
flange
F316/F316L
Socket weld
flange
Ti grade 1 clad to Hygienic fitting
304L backing
Ti grade 1 clad to Swagelok
304L backing
compatible fitting
Ti grade 1 clad to Swagelok
304L backing
compatible fitting
F316/F316L
Socket weld
flange
1/2-inch NPT
female adapter
Type N grooved
face
F316/F316L
Ti grade 1 clad to
304L backing
DIN11851
Ti grade 1 clad to
304L backing
DIN11864-1A Ti grade 1 clad to
304L backing
JIS B 2220
F316/F316L
Weld neck flange Form D
Hygienic
coupling
Hygienic
coupling
Hygienic
coupling
Socket weld
flange
Hygienic fitting
Model T025F
Code Description
621
1/2-inch
670
DN10
Tri-Clamp
compatible
DIN11851
Ti grade 1 clad to
304L backing
Ti grade 1 clad to
304L backing
Ti grade 1 clad to
304L backing
671
DN15
DIN11851
676
DN15
DIN11864-1A Ti grade 1 clad to Hygienic
304L backing
coupling
T-Series Straight-Tube Coriolis Flow and Density Meters
17
Fitting options continued
Model T050T
Code
525
526
613
Description
DN15
PN40 EN 1092-1
DN15
PN100 EN 1092-1
1/2-inch CL150 ASME B16.5
614
1/2-inch
CL300
ASME B16.5
615
1/2-inch
CL600
ASME B16.5
616
DN15
PN40
DIN 2526
617
DN15
PN100 DIN 2526
621
1/2-inch
638
#12
Tri-Clamp
compatible
VCO
639
#12
VCO
650
DN15
PN40
DIN 2512
654
671
DN15
DN15
PN40
EN 1092-1
DIN11851
676
DN15
781
15mm
20K
F316/F316L
F316/F316L
F316/F316L
Weld neck flange
Weld neck flange
Socket weld
flange
F316/F316L
Socket weld
flange
F316/F316L
Socket weld
flange
F316/F316L
Socket weld
flange
F316/F316L
Socket weld
flange
Ti grade 1 clad to Hygienic fitting
304L backing
Ti grade 1 clad to Swagelok
304L backing
compatible fitting
Ti grade 1 clad to Swagelok
304L backing
compatible fitting
F316/F316L
Socket weld
flange
Form B1
Form B2
Raised face
Dim. A
16.09 (409)
16.41 (417)
15.75 (400)
Dim. B
3 3/4 (95)
4 1/8 (105)
3 1/2 (89)
Raised face
16.27 (413)
3 3/4 (95)
Raised face
16.39 (417)
3 3/4 (95)
Type C face
16.09 (409)
3 3/4 (95)
Type E face
16.41 (417)
4 1/8 (105)
16.37 (416)
1 (25)
21.60 (549)
—
17.74 (451)
—
16.09 (409)
3 3/4 (95)
16.09 (409)
16.37 (416)
3 3/4 (95)
Rd 34 × 1/8
16.37 (416)
Rd 34 × 1/8
16.08 (409)
3 3/4 (95)
Dim. A
16.37 (416)
Dim. B
1 (25)
16.37 (416)
Rd 34 × 1/8
16.37 (416)
Rd 34 × 1/8
3/4-inch NPT
female adapter
Type N grooved
face
F316/F316L
Ti grade 1 clad to
304L backing
DIN11864-1A Ti grade 1 clad to
304L backing
JIS B 2220
F316/F316L
Weld neck flange Form D
Hygienic
coupling
Hygienic
coupling
Socket weld
flange
Tri-Clamp
compatible
DIN11851
Hygienic fitting
Model T050F
Code Description
621
1/2-inch
671
DN15
676
DN15
18
Ti grade 1 clad to
304L backing
Ti grade 1 clad to
304L backing
DIN11864-1A Ti grade 1 clad to
304L backing
Hygienic
coupling
Hygienic
coupling
T-Series Straight-Tube Coriolis Flow and Density Meters
Fitting options continued
Model T075T
Code
525
526
527
528
613
Description
DN15
PN40
DN15
PN100
DN25
PN40
DN25
PN100
1/2-inch CL150
614
1/2-inch
CL300
615
1/2-inch
CL600
616
DN15
PN40
617
DN15
PN100
618
DN25
PN40
619
DN25
PN100
622
3/4-inch
623
1-inch
628
1-inch
CL150
629
1-inch
CL300
630
1-inch
CL600
650
DN15
PN40
651
DN25
PN40
654
655
662
DN15
DN25
DN25
PN40
PN40
672
DN25
677
DN25
692
DN25
781
15mm
20K
782
25mm
20K
EN 1092-1
EN 1092-1
EN 1092-1
EN 1092-1
ASME B16.5
F316/F316L
F316/F316L
F316/F316L
F316/F316L
F316/F316L
Weld neck flange
Weld neck flange
Weld neck flange
Weld neck flange
Socket weld
flange
ASME B16.5 F316/F316L
Socket weld
flange
ASME B16.5 F316/F316L
Socket weld
flange
DIN 2526
F316/F316L
Socket weld
flange
DIN 2526
F316/F316L
Socket weld
flange
DIN 2526
F316/F316L
Socket weld
flange
DIN 2526
F316/F316L
Socket weld
flange
Tri-Clamp
Ti grade 1 clad to Hygienic fitting
compatible
304L backing
Tri-Clamp
Ti grade 1 clad to Hygienic fitting
compatible
304L backing
ASME B16.5 F316/F316L
Socket weld
flange
ASME B16.5 F316/F316L
Socket weld
flange
ASME B16.5 F316/F316L
Socket weld
flange
DIN 2512
F316/F316L
Socket weld
flange
DIN 2512
F316/F316L
Socket weld
flange
EN 1092-1
F316/F316L
Weld neck flange
EN 1092-1
F316/F316L
Weld neck flange
ISO 2853
Ti grade 1 clad to Hygienic
(IDF)
304L backing
coupling
DIN11851
Ti grade 1 clad to Hygienic
304L backing
coupling
DIN11864-1A Ti grade 1 clad to Hygienic
304L backing
coupling
SMS 1145
Ti grade 1 clad to Hygienic
304L backing
coupling
JIS B 2220
F316/F316L
Socket weld
flange
JIS B 2220
F316/F316L
Socket weld
flange
Form B1
Form B2
Form B1
Form B2
Raised face
Dim. A
21.15 (537)
21.47 (545)
21.75 (552)
22.23 (565)
20.81 (529)
Dim. B
3 3/4 (95)
4 1/8 (105)
4 1/2 (115)
5 1/2 (140)
3 1/2 (89)
Raised face
21.33 (542)
3 3/4 (95)
Raised face
21.45 (545)
3 3/4 (95)
Type C face
21.15 (537)
3 3/4 (95)
Type E face
21.47 (545)
4 1/8 (105)
Type C face
21.75 (552)
4 1/2 (115)
Type E face
22.23 (565)
5 1/2 (140)
21.57 (548)
1 (25)
21.43 (544)
2 (50)
Raised face
21.07 (535)
4 1/4 (108)
Raised face
21.81 (554)
4 7/8 (124)
Raised face
21.81 (554)
4 7/8 (124)
Type N grooved
face
Type N grooved
face
Form D
Form D
21.15 (537)
3 3/4 (95)
21.75 (552)
4 1/2 (115)
21.15 (537)
21.75 (552)
21.47 (545)
3 3/4 (95)
4 1/2 (115)
DN25
21.47 (545)
Rd 52 × 1/6
21.47 (545)
Rd 52 × 1/6
21.47 (545)
Rd 40 × 1/6
21.14 (537)
3 3/4 (95)
21.57 (548)
4 15/16 (125)
T-Series Straight-Tube Coriolis Flow and Density Meters
19
Fitting options continued
Model T075F
Code Description
613
1/2-inch CL150
614
1/2-inch
CL300
615
1/2-inch
CL600
616
DN15
PN40
617
DN15
PN100
618
DN25
PN40
619
DN25
PN100
622
3/4-inch
623
1-inch
628
1-inch
CL150
629
1-inch
CL300
630
1-inch
CL600
650
DN15
PN40
651
DN25
PN40
662
DN25
672
DN25
677
DN25
692
DN25
781
15mm
20K
782
25mm
20K
20
ASME B16.5
F316/F316L
Socket weld
flange
ASME B16.5 F316/F316L
Socket weld
flange
ASME B16.5 F316/F316L
Socket weld
flange
DIN 2526
F316/F316L
Socket weld
flange
DIN 2526
F316/F316L
Socket weld
flange
DIN 2526
F316/F316L
Socket weld
flange
DIN 2526
F316/F316L
Socket weld
flange
Tri-Clamp
Ti grade 1 clad to Hygienic fitting
compatible
304L backing
Tri-Clamp
Ti grade 1 clad to Hygienic fitting
compatible
304L backing
ASME B16.5 F316/F316L
Socket weld
flange
ASME B16.5 F316/F316L
Socket weld
flange
ASME B16.5 F316/F316L
Socket weld
flange
DIN 2512
F316/F316L
Socket weld
flange
DIN 2512
F316/F316L
Socket weld
flange
ISO 2853
Ti grade 1 clad to Hygienic
(IDF)
304L backing
coupling
DIN11851
Ti grade 1 clad to Hygienic
304L backing
coupling
DIN11864-1A Ti grade 1 clad to Hygienic
304L backing
coupling
SMS 1145
Ti grade 1 clad to Hygienic
304L backing
coupling
JIS B 2220
F316/F316L
Socket weld
flange
JIS B 2220
F316/F316L
Socket weld
flange
T-Series Straight-Tube Coriolis Flow and Density Meters
Raised face
Dim. A
20.81 (529)
Dim. B
3 1/2 (89)
Raised face
21.33 (542)
3 3/4 (95)
Raised face
21.45 (545)
3 3/4 (95)
Type C face
21.15 (537)
3 3/4 (95)
Type E face
21.47 (545)
4 1/8 (105)
Type C face
21.75 (552)
4 1/2 (115)
Type E face
22.23 (565)
5 1/2 (140)
21.57 (548)
1 (25)
21.43 (544)
2 (50)
Raised face
21.07 (535)
4 1/4 (108)
Raised face
21.81 (554)
4 7/8 (124)
Raised face
21.81 (554)
4 7/8 (124)
Type N grooved
face
Type N grooved
face
21.15 (537)
3 3/4 (95)
21.75 (552)
4 1/2 (115)
21.47 (545)
DN25
21.47 (545)
Rd 52 × 1/6
21.47 (545)
Rd 52 × 1/6
21.47 (545)
Rd 40 × 1/6
21.14 (537)
3 3/4 (95)
21.57 (548)
4 15/16 (125)
Fitting options continued
Model T100T
Code
527
528
618
Description
DN25
PN40 EN 1092-1
DN25
PN100 EN 1092-1
DN25
PN40 DIN 2526
619
DN25
PN100 DIN 2526
623
1-inch
624
628
1-1/2inch
1-inch
Tri-Clamp
compatible
Tri-Clamp
compatible
CL150 ASME B16.5
629
1-inch
CL300
ASME B16.5
630
1-inch
CL600
ASME B16.5
641
1-1/2inch
1-1/2inch
CL150
ASME B16.5
CL300
ASME B16.5
CL600
ASME B16.5
651
1-1/2inch
DN25
652
DN40
655
656
658
659
672
DN25
DN40
DN40
DN40
DN25
677
DN25
681
DN40
682
DN40
782
25mm
783
40mm
642
643
Weld neck flange
Weld neck flange
Socket weld
flange
F316/F316L
Socket weld
flange
Ti grade 1 clad to Hygienic fitting
304L backing
Ti grade 1 clad to Hygienic fitting
304L backing
F316/F316L
Socket weld
flange
F316/F316L
Socket weld
flange
F316/F316L
Socket weld
flange
F316/F316L
Socket weld
flange
F316/F316L
Socket weld
flange
Form B1
Form B2
Type C face
Dim. A
26.19 (665)
26.67 (677)
26.19 (665)
Type E face
26.55 (674)
5 1/2 (140)
26.23 (666)
2 (50)
26.23 (666)
2 (50)
Raised face
25.51 (648)
4 1/4 (108)
Raised face
26.25 (667)
4 7/8 (124)
Raised face
26.37 (670)
4 7/8 (124)
Raised face
25.77 (655)
5 (127)
Raised face
26.39 (670)
6 1/8 (155)
F316/F316L
Raised face
26.51 (673)
6 1/8 (155)
Type N grooved
face
Type N grooved
face
Form D
Form D
Form B1
Form B2
26.19 (665)
4 1/2 (115)
26.29 (668)
5 15/16 (150)
26.19 (665)
26.29 (668)
26.29 (668)
27.11 (689)
26.23 (666)
4 1/2 (115)
5 15/16 (150)
5 15/16 (150)
6 11/16 (170)
Rd 52 × 1/6
26.23 (666)
Rd 52 × 1/6
Type C face
26.29 (668)
5 15/16 (150)
Type E face
26.69 (678)
6 11/16 (170)
26.13 (664)
4 15/16 (125)
26.19 (665)
5 1/2 (140)
F316/F316L
F316/F316L
F316/F316L
Socket weld
flange
PN40 DIN 2512
F316/F316L
Socket weld
flange
PN40 DIN 2512
F316/F316L
Socket weld
flange
PN40 EN 1092-1
F316/F316L
Weld neck flange
PN40 EN 1092-1
F316/F316L
Weld neck flange
PN40 EN 1092-1
F316/F316L
Weld neck flange
PN100 EN 1092-1
F316/F316L
Weld neck flange
DIN11851
Ti grade 1 clad to Hygienic
304L backing
coupling
DIN11864-1A Ti grade 1 clad to Hygienic
304L backing
coupling
PN40 DIN 2526
F316/F316L
Socket weld
flange
PN100 DIN 2526
F316/F316L
Socket weld
flange
20K
JIS B 2220
F316/F316L
Socket weld
flange
20K
JIS B 2220
F316/F316L
Socket weld
flange
Dim. B
4 1/2 (115)
5 1/2 (140)
4 1/2 (115)
T-Series Straight-Tube Coriolis Flow and Density Meters
21
Fitting options continued
Model T100F
Code Description
618
DN25
PN40
DIN 2526
F316/F316L
Socket weld
flange
PN100 DIN 2526
F316/F316L
Socket weld
flange
Tri-Clamp
Ti grade 1 clad to Hygienic fitting
compatible
304L backing
Tri-Clamp
Ti grade 1 clad to Hygienic fitting
compatible
304L backing
CL150 ASME B16.5 F316/F316L
Socket weld
flange
CL300 ASME B16.5 F316/F316L
Socket weld
flange
CL600 ASME B16.5 F316/F316L
Socket weld
flange
CL150 ASME B16.5 F316/F316L
Socket weld
flange
CL300 ASME B16.5 F316/F316L
Socket weld
flange
PN40 DIN 2512
F316/F316L
Socket weld
flange
PN40 DIN 2512
F316/F316L
Socket weld
flange
DIN11851
Ti grade 1 clad to Hygienic
304L backing
coupling
DIN11864-1A Ti grade 1 clad to Hygienic
304L backing
coupling
PN40 DIN 2526
F316/F316L
Socket weld
flange
PN100 DIN 2526
F316/F316L
Socket weld
flange
619
DN25
623
1-inch
624
628
1-1/2inch
1-inch
629
1-inch
630
1-inch
641
651
1-1/2inch
1-1/2inch
DN25
652
DN40
672
DN25
677
DN25
681
DN40
682
DN40
782
25mm
20K
JIS B 2220
F316/F316L
783
40mm
20K
JIS B 2220
F316/F316L
642
22
Socket weld
flange
Socket weld
flange
T-Series Straight-Tube Coriolis Flow and Density Meters
Type C face
Dim. A
Dim. B
26 3/16 (665) 4 1/2 (115)
Type E face
26 9/16 (674) 5 1/2 (140)
26 1/4 (668)
2 (50)
26 1/4 (666)
2 (50)
Raised face
25 1/2 (648)
4 1/4 (108)
Raised face
26 1/4 (667)
4 7/8 (124)
Raised face
26 3/8 (670)
4 7/8 (124)
Raised face
25 3/4 (655)
5 (127)
Raised face
26 3/8 (670)
6 1/8 (155)
Type N grooved
face
Type N grooved
face
26 3/16 (665) 4 1/2 (115)
26 5/16 (668) 5 15/16 (150)
26 1/4 (666)
Rd 52 × 1/6
26 1/4 (667)
Rd 52 × 1/6
Type C face
26 5/16 (668) 5 15/16 (150)
Type E face
26 11/16 (678) 6 11/16 (170)
26 1/8 (664)
4 15/16 (125)
26 3/16 (665) 5 1/2 (140)
Fitting options continued
Model T150T
Code Description
624
1-1/2inch
625
2-inch
641
644
1-1/2inch
1-1/2inch
1-1/2inch
2-inch
645
2-inch
646
2-inch
652
DN40
653
DN50
656
657
658
659
660
661
663
DN40
DN50
DN40
DN40
DN50
DN50
DN51
673
DN40
674
DN50
678
DN50
681
DN40
682
DN40
683
DN50
684
DN50
693
DN51
783
40mm
784
50mm
642
643
Tri-Clamp
compatible
Tri-Clamp
compatible
CL150 ASME B16.5
Ti grade 1 clad to Hygienic fitting
304L backing
Ti grade 1 clad to Hygienic fitting
304L backing
F316/F316L
Socket weld
flange
CL300 ASME B16.5 F316/F316L
Socket weld
flange
CL600 ASME B16.5 F316/F316L
Socket weld
flange
CL150 ASME B16.5 F316/F316L
Socket weld
flange
CL300 ASME B16.5 F316/F316L
Socket weld
flange
CL600 ASME B16.5 F316/F316L
Socket weld
flange
PN40 DIN 2512
F316/F316L
Socket weld
flange
PN40 DIN 2512
F316/F316L
Socket weld
flange
PN40 EN 1092-1
F316/F316L
Weld neck flange
PN40 EN 1092-1
F316/F316L
Weld neck flange
PN40 EN 1092-1
F316/F316L
Weld neck flange
PN100 EN 1092-1
F316/F316L
Weld neck flange
PN40 EN 1092-1
F316/F316L
Weld neck flange
PN100 EN 1092-1
F316/F316L
Weld neck flange
ISO 2853
Ti grade 1 clad to Hygienic
(IDF)
304L backing
coupling
DIN11851
Ti grade 1 clad to Hygienic
304L backing
coupling
DIN11851
Ti grade 1 clad to Hygienic
304L backing
coupling
DIN11864-1A Ti grade 1 clad to Hygienic
304L backing
coupling
PN40 DIN 2526
F316/F316L
Socket weld
flange
PN100 DIN 2526
F316/F316L
Socket weld
flange
PN40 DIN 2526
F316/F316L
Socket weld
flange
PN100 DIN 2526
F316/F316L
Socket weld
flange
SMS 1145
Ti grade 1 clad to Hygienic
304L backing
coupling
20K
JIS B 2220
F316/F316L
Socket weld
flange
20K
JIS B 2220
F316/F316L
Socket weld
flange
Dim. A
32.04 (814)
Dim. B
2 (50)
32.04 (814)
2 1/2 (64)
Raised face
31.46 (799)
5 (127)
Raised face
32.08 (815)
6 1/8 (155)
Raised face
32.32 (821)
6 1/8 (155)
Raised face
31.68 (805)
6 (152)
Raised face
32.30 (820)
6 1/2 (165)
Raised face
32.56 (827)
6 1/2 (165)
Type N grooved
face
Type N grooved
face
Form D
Form D
Form B1
Form B2
Form B1
Form B2
31.74 (806)
5 7/8 (150)
32.02 (813)
6 1/2 (165)
31.74 (806)
32.02 (813)
31.74 (806)
32.56 (827)
32.02 (813)
32.84 (834)
32.04 (814)
5 7/8 (150)
6 1/2 (165)
5 7/8 (150)
6 11/16 (170)
6 1/2 (165)
7 11/16 (195)
DN51
32.60 (828)
Rd 65 × 1/6
32.04 (814)
Rd 78 × 1/6
32.04 (814)
Rd 78 × 1/6
Type C face
31.74 (806)
5 7/8 (150)
Type E face
32.38 (822)
6 11/16 (170)
Type C face
32.02 (813)
6 1/2 (165)
Type E face
32.66 (829)
7 11/16 (195)
32.04 (814)
Rd 70 × 1/6
31.88 (810)
5 1/2 (140)
31.89 (810)
6 1/8 (155)
T-Series Straight-Tube Coriolis Flow and Density Meters
23
Fitting options continued
Model T150F
Code Description
624
1-1/2inch
625
2-inch
641
644
1-1/2inch
1-1/2inch
1-1/2inch
2-inch
645
2-inch
646
2-inch
652
DN40
653
DN50
663
DN51
673
DN40
674
DN50
678
DN50
681
DN40
682
DN40
683
DN50
684
DN50
693
DN51
783
40mm
784
50mm
642
643
24
Tri-Clamp
compatible
Tri-Clamp
compatible
CL150 ASME B16.5
Ti grade 1 clad to Hygienic fitting
304L backing
Ti grade 1 clad to Hygienic fitting
304L backing
F316/F316L
Socket weld
flange
CL300 ASME B16.5 F316/F316L
Socket weld
flange
CL600 ASME B16.5 F316/F316L
Socket weld
flange
CL150 ASME B16.5 F316/F316L
Socket weld
flange
CL300 ASME B16.5 F316/F316L
Socket weld
flange
CL600 ASME B16.5 F316/F316L
Socket weld
flange
PN40 DIN 2512
F316/F316L
Socket weld
flange
PN40 DIN 2512
F316/F316L
Socket weld
flange
ISO 2853
Ti grade 1 clad to Hygienic
(IDF)
304L backing
coupling
DIN11851
Ti grade 1 clad to Hygienic
304L backing
coupling
DIN11851
Ti grade 1 clad to Hygienic
304L backing
coupling
DIN11864-1A Ti grade 1 clad to Hygienic
304L backing
coupling
PN40 DIN 2526
F316/F316L
Socket weld
flange
PN100 DIN 2526
F316/F316L
Socket weld
flange
PN40 DIN 2526
F316/F316L
Socket weld
flange
PN100 DIN 2526
F316/F316L
Socket weld
flange
SMS 1145
Ti grade 1 clad to Hygienic
304L backing
coupling
20K
JIS B 2220
F316/F316L
Socket weld
flange
20K
JIS B 2220
F316/F316L
Socket weld
flange
T-Series Straight-Tube Coriolis Flow and Density Meters
Dim. A
32.04 (814)
Dim. B
2 (50)
32.04 (814)
2 1/2 (64)
Raised face
31.46 (799)
5 (127)
Raised face
32.08 (815)
6 1/8 (155)
Raised face
32.32 (821)
6 1/8 (155)
Raised face
31.68 (805)
6 (152)
Raised face
32.30 (820)
6 1/2 (165)
Raised face
32.56 (827)
6 1/2 (165)
Type N grooved
face
Type N grooved
face
31.74 (806)
5 7/8 (150)
32.02 (813)
6 1/2 (165)
32.04 (814)
DN51
32.60 (828)
Rd 65 × 1/6
32.04 (814)
Rd 78 × 1/6
32.04 (814)
Rd 78 × 1/6
Type C face
31.74 (806)
5 7/8 (150)
Type E face
32.38 (822)
6 11/16 (170)
Type C face
32.02 (813)
6 1/2 (165)
Type E face
32.66 (829)
7 11/16 (195)
32.04 (814)
Rd 70 × 1/6
31.88 (810)
5 1/2 (140)
31.89 (810)
6 1/8 (155)
Ordering information
Model
Product description
Standard sensor models
T025T
Micro Motion Coriolis T-Series sensor; 1/4-inch; straight tube; titanium; 32 Ra (0.8 m) surface finish
T050T
Micro Motion Coriolis T-Series sensor; 1/2-inch; straight tube; titanium; 32 Ra (0.8 m) surface finish
T075T
Micro Motion Coriolis T-Series sensor; 3/4-inch; straight tube; titanium; 32 Ra (0.8 m) surface finish
T100T
Micro Motion Coriolis T-Series sensor; 1-inch; straight tube; titanium; 32 Ra (0.8 m) surface finish
T150T
Micro Motion Coriolis T-Series sensor; 1 1/2-inch; straight tube; titanium; 32 Ra (0.8 m) surface finish
Improved surface finish sensor models
T025F
Micro Motion Coriolis T-Series sensor; 1/4-inch; straight tube; titanium; 15 Ra (0.38 m) surface finish
T050F
Micro Motion Coriolis T-Series sensor; 1/2-inch; straight tube; titanium; 15 Ra (0.38 m) surface finish
T075F
Micro Motion Coriolis T-Series sensor; 3/4-inch; straight tube; titanium; 15 Ra (0.38 m) surface finish
T100F
Micro Motion Coriolis T-Series sensor; 1-inch; straight tube; titanium; 15 Ra (0.38 m) surface finish
T150F
Micro Motion Coriolis T-Series sensor; 1 1/2-inch; straight tube; titanium; 15 Ra (0.38 m) surface finish
Code
Fitting options
###
See fittings tables on pages 17–24.
Code
Case options
S
1450 psig (100 bar) containment
P
(1)
Purge fittings (two 1/2-inch NPT female); 725 psig (50 bar) containment
Code
Electronics interface
Q
4-wire polyurethane-painted aluminum integral core processor for remotely mounted transmitter with MVD Technology
A
4-wire stainless steel integral core processor for remotely mounted transmitter with MVD Technology
V
4-wire polyurethane-painted aluminum integral core processor with extended mount for remotely mounted transmitter with
MVD Technology
B
4-wire stainless steel integral core processor with extended mount for remotely mounted transmitter with MVD Technology
C
Integrally mounted Model 1700 or 2700 transmitter
R
9-wire polyurethane-painted junction box — not available with Models T025 or T050
H
9-wire polyurethane-painted junction box with extended mount — not available with Models T025 or T050
Code
Conduit connections
Electronics interface codes Q, A, V, and B
B
1/2-inch NPT — no gland
E
M20 — no gland
F
Brass/nickel cable gland (cable diameter 0.335 to 0.394 inches [8.5 to 10 mm])
G
Stainless steel cable gland (cable diameter 0.335 to 0.394 inches [8.5 to 10 mm])
Electronics interface codes R and H (9-wire junction box)
A
3/4-inch NPT — no gland
H
3/4-inch NPT with brass/nickel cable gland
J
3/4-inch NPT with stainless steel cable gland
Electronics interface code C (integrally mounted transmitter)
A
No gland
Continued on next page
(1) Not available with sensors with improved surface finish option.
T-Series Straight-Tube Coriolis Flow and Density Meters
25
Ordering information continued
Available with electronics interface codes:
Code
Approval
M
N
U
(2)
Q, A, V, B, R, H
C
W, D, Y, E
Micro Motion standard (no approval, without CE/EAC markings)
•
•
• (1)
Micro Motion standard / PED compliant (with CE/EAC markings)
•
•
• (1)
UL
•
•
•
C
CSA (Canada only)
•
•
•
A
CSA (U.S.A. and Canada)
•
•
•
Z
ATEX — Equipment Category 2 (Zone 1) / PED compliant
•
•
•
•
I
IECEx Zone 1
•
•
T
TIIS — T4 temperature classification (not available for quote outside Japan)
•
•
J (3)
Hardware ready for TIIS approval (EPM Japan only)
•
•
V (4)
ATEX — Equipment Category 3 (Zone 2) / PED compliant
3 (4)
IECEx Zone 2
•
2 (4)
CSA Class I Div. 2 (U.S.A. and Canada)
•
G
Country specific approval — Requires a selection from the Approvals
section of the “Certificate, Tests, Calibrations and Services” model code
option
Code
Language
A
Danish installation manual
C
Czech installation manual
D
Dutch installation manual
E
English installation manual
F
French installation manual
G
German installation manual
H
Finnish installation manual
I
Italian installation manual
J
Japanese installation manual
M
Chinese installation manual
N
Norwegian installation manual
O
Polish installation manual
S
Spanish installation manual
W
Swedish installation manual
B
Hungarian CE requirements and English installation manual
K
Slovak CE requirements and English installation manual
T
Estonian CE requirements and English installation manual
U
Greek CE requirements and English installation manual
L
Latvian CE requirements and English installation manual
V
Lithuanian CE requirements and English installation manual
Y
Slovenian CE requirements and English installation manual
•
•
Continued on next page
(1)
(2)
(3)
(4)
26
No barrier included.
Not available with models T025F or T050F.
Approval code J Requires conduit connection code E if electronics interface option Q, A or H are used.
Available only with electronics interface option C.
T-Series Straight-Tube Coriolis Flow and Density Meters
•
•
Ordering information continued
Code
Future option 1
Z
Reserved for future use
Code
Future option 2
Z
Reserved for future use
Code
Measurement application software
Z
No measurement application software
Code
Factory options
Z
Standard product
X
ETO product
Code
Certificat, Tests, Calibrations and Services (not required, all are optional)
Material Quality Examination Test and Certificate
MC
Material Inspection Certificate 3.1 (Supplier Lot Traceability per EN 10204)
HT
Hydrostatic Test Certificate 3.1
PN
Pneumatic Test Certificate 3.1
Pressure Testing (select any from this group)
Dye Penetrant Examination (select any from this group)
D1
Dye Penetrant Test Package 3.1 (Process Connection only; Liquid Dye Penetration NDE Qualification)
D2
Dye Penetrant Test Package 3.1 (Case only; Liquid Dye Penetration NDE Qualification)
Weld Examination
WP
Weld Procedure Package (Weld Map, Weld Procedure Specification, Weld Procedure Qualification Record, Welder
Performance Qualification)
O2
Declaration of Compliance Oxygen Service 2.1
GR
Russian GOST Calibration Verification Certificate
Special Cleaning
Metrology Compliance
Accredited Calibration
IC
ISO17025 Accredited Calibration and Certificates (9 points total)
Special Calibration Options (Select either none, CV, or CV with one of the additional verification point options)
CV
Custom verification (after original verification points)
01
Add 1 additional verification point
02
Add 2 additional verification points
03
Add 3 additional verification points
06
Add up to 6 additional verification points
08
Add 8 additional verification points
16
Add up to 16 additional verification points
Sensor Completion Options (select any from this group)
WG
Witness General
SP
Special Packaging
R1
EAC Zone 1 - Hazardous Area Approval
B1
INMETRO Zone 1 - Hazardous Area Approval
Country Specific Approvals (must select only one when approval option G selected)
Typical model number: T025T 613 S Q B M E Z Z Z Z
T-Series Straight-Tube Coriolis Flow and Density Meters
27
T-Series Flow and Density Meters
Product Data Sheet
PS-00371, Rev. I
Emerson Process Management
Americas
7070 Winchester Circle
Boulder, Colorado USA 80301
www.MicroMotion.com
www.Rosemount.com
T: +1 800 522 6277
T: +1 (303) 527 5200
F: +1 (303) 530 8459
Mexico
Argentina
Brazil
Venezuela
Chile
T: 52 55 5809 5300
T: 54 11 4837 7000
T: 55 15 3413 8000
T: 58 26 1300 8100
T: 56 2 2928 4800
August 2015
Emerson Process Management
Europe/Middle East
Emerson Process Management
Central & Eastern Europe T: +41 41 7686 111
Dubai
T: +971 4 811 8100
Abu Dhabi
T: +971 2 697 2000
France
T: 0800 917 901
Germany
T: 0800 182 5347
Italy
T: 8008 77334
The Netherlands
T: +31 (0) 70 413 6666
Belgium
T: +32 2 716 77 11
Spain
T: +34 913 586 000
U.K.
T: 0870 240 1978
Russia/CIS
T: +7 495 981 9811
Australia
China
India
Japan
South Korea
Singapore
Asia Pacific
T: (61) 3 9721 0200
T: (86) 21 2892 9000
T: (91) 22 6662 0566
T: (81) 3 5769 6803
T: (82) 2 3438 4600
T: (65) 6 777 8211
© 201Micro Motion, Inc. All rights reserved.
The Emerson logo is a trademark and service mark of Emerson Electric Co. Micro Motion, ELITE, ProLink, MVD and MVD Direct Connect marks are
marks of one of the Emerson Process Management family of companies. All other marks are property of their respective owners.
Micro Motion supplies this publication for informational purposes only. While every effort has been made to ensure accuracy, this publication is not
intended to make performance claims or process recommendations. Micro Motion does not warrant, guarantee, or assume any legal liability for the
accuracy, completeness, timeliness, reliability, or usefulness of any information, product, or process described herein. We reserve the right to
modify or improve the designs or specifications of our products at any time wihout notice. For actual product information and recommendations,
please contact your local Micro Motion representative.